BA IVDM-7003 Teil 1 GB

Transcription

In Car Entertainment Multimedia
7 607 003 531
Aspen IVDM-7003
Chicago IVDM-7003
7 607 004 504
Operating Instructions
1
www.blaupunkt.com
03.02.2006, 8:32 Uhr
2
Remote control – General functions
1
31
2
29
6
8
27
10
11
12
25
13
15
23
18
2
03.02.2006, 8:32 Uhr
Remote control – General functions
1
MUTE button
Press once to mute the car sound system
Press again to cancel mute
G
TILT - / + buttons
Tilt monitor forward with - button
Tilt monitor backward with + button
2
OPEN/CLOSE button
Open or close the monitor
I
LCD button
Select the colour of the display illumination
6
DISP / WALLPAPER button
Monitor closed: Toggle between time display and display
of active signal source
Monitor open: Change the wallpaper
K
SRC button
Select the signal source
On the setup menu: Select among the setup menus
(DVD > AUDIO > SCREEN > USER)
8
VOL
/
buttons
Increase the volume by pressing the
Decrease the volume by pressing the
M
SOUND / DSP button
Call up the menu for the sound settings
O
/ POWER button
Switch the unit on/off
button
button
:
NAVI button
Select the navigation mode (only with connected navigation system, e.g. TravelPilot EX-V)
;
/
and / buttons
Select menu entries
<
ENTER button
Confirm the selected menu entry
=
SETUP button
Call and exit the setup menu
?
DOWNMIX button
Change the multi-channel surround signal to stereo signal
B
REAR button
Display the image of a connected back-up camera
(optional equipment)
3
3
03.02.2006, 8:32 Uhr
4
Remote control – DVD operation
3
30
4
5
6
7
28
9
11
12
14
24
16
17
21
4
19
03.02.2006, 8:32 Uhr
Remote control – DVD operation
3
TA / AUDIO button
Select playback language
E
REPEAT button
Repeat a chapter or title
4
AF / SUBTITLE button
Select the language of the subtitles or hide the subtitles
H
RDS / MENU button
Call and exit the DVD main menu
5
Number buttons 0 - 9
Enter the title and chapter number
L
/ button
Select a chapter up/down
6
DISP / WALLPAPER button
Call and exit the DVD menu
N
7
/ PLAY/PAUSE button
Pause and restart playback
REG / ANGLE button
Select the camera perspective if different camera perspectives are stored on the DVD
9
/ RETURN button
Stop playback
;
/
and / buttons
Select menu entries in the DVD main menu
<
ENTER button
Confirm the selection in the DVD main menu
>
/
button
Fast scan forward/back
@
PTY / ZOOM button
Enlarge the image area
A
WIDE button
Change image format
C
GOTO button
Call DVD menu for direct selection of a title or chapter
5
5
03.02.2006, 8:32 Uhr
6
Remote control – Radio operation
3
30
3
TA / AUDIO button
Switch priority for traffic announcements on/off
4
AF / SUBTITLE button
Switch AF function (Alternate Frequency) on/off
5
Number buttons 1 - 6
Call up stored stations
>
/
buttons
Manual station search up/down
@
PTY / ZOOM button
Call up a list with available programme types
H
RDS / MENU button
Call up the menu for RDS settings
J
BAND button
Select the waveband/memory bank
(FM1 > FM2 > FM3 > MW)
L
/ buttons
Automatic station search up/down
N
REG / ANGLE button
Switch REG function (regional programmes) on/off
4
5
28
26
14
24
16
6
03.02.2006, 8:32 Uhr
Remote control – CD/CD changer/MP3 mode
7
/ PLAY/PAUSE button
Pause and restart playback
9
button
Stop playback
;
/
buttons
Scroll file list up/down
/
buttons
Select CD or folder up/down
28
7
<
ENTER button
Call up the file selected in the file list via scrolling
9
>
/
buttons
D
SCAN button
Scan and play tracks or files for approx. 10 seconds
12
E
REPEAT button
Repeat track or CD and file or folder
14
F
MIX button
Random playback of tracks or files
L
/ button
Select title of file up/down
11
22
20
21
21
7
7
03.02.2006, 8:32 Uhr
8
Controls – Device
32 33
48 47 46 45
8
34
42
44 43
35 36 37
42
41 40
03.02.2006, 8:32 Uhr
39
38
Controls – Device
P
SRC button
Select the signal source
Q
NAVI button
Select the navigation mode (only with connected navigation system, e.g. TravelPilot EX-V)
R
LCD display
S
DIS / FLIP button
Monitor closed
Press short: Switching between time display and display
of active signal source
Press long: Select colour of display illumination
Monitor open
Tilt monitor horizontally to the front
T
/ CLOSE button
Open or close the monitor
U
Retractable TFT monitor
V
button
Unlock the detachable control panel
W
TUNE / button
Radio operation: Automatic station search
DVD operation: Select chapter
CD/CD changer/MP3 mode: Select track/file
X
Y
BND / BSM button
Press short: Select waveband/memory bank
Press long: Store station automatically
Z
Station button 1 / -DISC
CD changer/MP3 mode: Select CD/folder downward
Station button 2 / DISC+
CD changer/MP3 mode: Select CD/folder upward
Station button 3 / ZOOM
DVD operation: Enlarge the image area
Station button 4 / RPT
DVD/CD/CD changer/MP3 mode: Repeat chapter
or title/track or CD/file or folder
Station button 5 / MIX
CD/CD changer/MP3 mode: Play tracks/files in
random order
Station button 6 / SCAN
CD/CD changer/MP3 mode: Play each track/file for
approx. 10 seconds
[
button
Press short: Mute the car sound system
Press long: Switch the device on/off
\
CD/DVD tray
]
button
Interrupt and restart CD/DVD playback
a
button
Eject CD/DVD
b
VOL - / + buttons
Adjust the volume
c
Infrared receiver for remote control
Reset button
9
9
03.02.2006, 8:32 Uhr
10
Safety notes
Road safety
Failure to observe traffic may result in serious accidents.
To avoid any distraction from the traffic, observe the following items:
•
Familiarise yourself with the operation of the Aspen/Chicago IVDM-7003 before driving.
•
Operate the Aspen/Chicago IVDM-7003 while driving only if the traffic situation allows it. In case of doubt, stop at a
suitable location and operate the Aspen/Chicago IVDM-7003 while the vehicle is standing.
•
Insert or eject a CD/DVD only while the vehicle is standing.
•
For safety reasons, the image playback of DVD only occurs while the vehicle is standing.
•
You should always be able to hear police, fire and ambulance sirens in good time from inside your vehicle. Listen to
your car sound system at a suitable volume level during your journey.
Laser product
The internal CD/DVD drive is a class 1 laser product with a visible/invisible laser beam that may pose a dangerous
radiation to humans. The CD/DVD drive may only be operated according to the specified instructions. Never open the
housing and do not attempt to perform any repairs yourself. Service should always be performed by trained personnel.
10
03.02.2006, 8:32 Uhr
Contents
Controls – Remote control ............................................ 2
Controls – Device ........................................................... 8
Safety notes .................................................................. 10
User notes ..................................................................... 14
Safety precautions .................................................................
Care instructions for CDs/DVDs ...........................................
Usable media ..........................................................................
Region code ............................................................................
License ....................................................................................
Inserting batteries in the remote control .............................
14
15
15
16
16
16
Notes about these instructions .................................. 17
Theft protection ............................................................ 18
Detachable control panel ...................................................... 18
Removing the control panel .................................................................. 18
Attaching the control panel ................................................................... 18
Activating the device code .................................................... 19
Switching on coded devices after a voltage interruption ....................... 19
Introduction .................................................................. 20
Operating options .................................................................................. 20
Switching the device on/off ................................................................... 20
Inserting a CD/DVD .............................................................................. 21
Ejecting a CD/DVD ............................................................................... 21
Adjusting the volume ............................................................................. 22
Activating mute ..................................................................................... 22
Cancelling mute .................................................................................... 22
Closing/opening the monitor ................................................................. 23
Setting the monitor tilt ........................................................................... 23
Selecting the signal source ................................................................... 23
Sound settings ...................................................................................... 24
Switching the Downmix mode on/off ..................................................... 25
Selecting the display illumination colour ............................................... 25
Show/hide the image of a back-up camera ........................................... 26
Automatic through connection of telephone calls ................................. 26
Radio mode ................................................................... 27
Radio menu ........................................................................................... 27
Touch screen menu in radio mode ........................................................ 27
Switching to radio mode ........................................................................ 28
Switching RDS (Radio Data System) on/off .......................................... 28
Switching the RDS function AF (Alternate Frequency) on/off ............... 29
Switching the RDS function REG (Regional Programmes) on/off ......... 29
Selecting the waveband/memory bank ................................................. 30
Automatic station search ....................................................................... 30
Manual station search ........................................................................... 30
Storing stations manually ...................................................................... 31
Automatically storing stations ............................................................... 31
Calling up stored stations ...................................................................... 31
Station search by programme type ....................................................... 32
Traffic information stations .................................................................... 33
Switching traffic announcement priority on/off ...................................... 33
Setting the volume for traffic announcements ....................................... 34
Cancelling the current traffic announcement ......................................... 34
11
11
03.02.2006, 8:32 Uhr
12
Contents
DVD operation .............................................................. 35
CD-changer mode ........................................................ 46
DVD menu ............................................................................................ 35
Touch screen menu in DVD mode ........................................................ 35
Switching to DVD mode ........................................................................ 36
Starting playback .................................................................................. 36
Interrupting playback (freeze frame) ..................................................... 36
Exiting playback .................................................................................... 36
Selecting a chapter ............................................................................... 37
Direct selection of a title or chapter ....................................................... 37
Fast search ........................................................................................... 38
Selecting the playback language .......................................................... 38
Selecting the subtitle language ............................................................. 39
Repeating a chapter or title ................................................................... 39
Switching the image format ................................................................... 39
Enlarging an image area (Zoom) .......................................................... 39
Image settings ....................................................................................... 40
Selecting the camera perspective (Angle) ............................................ 40
Calling the DVD main menu .................................................................. 41
CD changer menu ................................................................................. 46
Touch screen menu in CD changer mode ............................................. 46
CD changers ......................................................................................... 47
Activating the CD changer mode .......................................................... 47
Interrupting playback (pause) ............................................................... 47
Selecting CDs ....................................................................................... 47
Selecting tracks on the currently playing CD ........................................ 48
Fast search ........................................................................................... 48
Repeating tracks (Repeat) .................................................................... 48
Random track play (MIX) ...................................................................... 49
Scanning all tracks (Scan) .................................................................... 49
Audio CD mode ............................................................ 42
Audio CD menu ..................................................................................... 42
Touch screen menu in Audio CD mode ................................................. 42
Activating the audio CD mode .............................................................. 43
Selecting tracks ..................................................................................... 43
Fast search ........................................................................................... 44
Repeating tracks (Repeat) .................................................................... 44
Random track play (MIX) ...................................................................... 45
Scanning all tracks (Scan) .................................................................... 45
MP3 CD mode ............................................................... 50
MP3 CD menu ...................................................................................... 50
Touch screen menu in MP3 CD mode .................................................. 50
Activating the MP3 CD mode ................................................................ 51
Selecting folders ................................................................................... 51
Selecting files ........................................................................................ 51
Fast search ........................................................................................... 52
Repeating files (Repeat) ....................................................................... 52
Random play of files (MIX) .................................................................... 53
Scanning all files (Scan) ....................................................................... 53
External sources .......................................................... 54
Add-on equipment ................................................................. 54
Navigation system ................................................................. 55
Voice output during navigation mode .................................................... 55
12
03.02.2006, 8:32 Uhr
Contents
Setup menu ................................................................... 56
User setup ............................................................................... 74
Setup menu ........................................................................................... 56
Selecting the setup menu ..................................................................... 56
Performing settings in the setup menu ................................................. 57
Changing the password ........................................................................ 74
Wallpapers ............................................................................................ 74
Selecting the wallpaper ......................................................................... 75
Automatic image change ...................................................................... 76
Deleting wallpapers ............................................................................... 76
Loading wallpapers ............................................................................... 77
Setting date and time ............................................................................ 79
Selecting the external signal source ..................................................... 79
Factory settings ..................................................................................... 80
Restart of the device software .............................................................. 81
DVD setup ............................................................................... 57
Selecting a language ............................................................................ 57
Selecting the screen display mode ....................................................... 58
Setting the parental control level ........................................................... 59
Audio setup ............................................................................ 60
Setting the input level for external audio sources ................................. 60
Setting Dolby ProLogic 2 (Chicago IVDM-7003 only) ........................... 60
Setting environment audio effects (Chicago IVDM-7003 only) ............. 61
Setting bass and treble (Aspen IVDM-7003 only) ................................. 61
Setting the speaker balance ................................................................. 62
Downmix function (Aspen IVDM-7003) ................................................. 62
Downmix function (Chicago IVDM-7003) .............................................. 63
7-band equaliser (Chicago IVDM-7003 only) ........................................ 64
Speaker setup (Aspen IVDM-7003) ...................................................... 65
Speaker setup (Chicago IVDM-7003) ................................................... 66
Setting a delay time .............................................................................. 67
Adjusting the speaker level ................................................................... 67
Setting the dynamic range .................................................................... 68
Setting volume decrease for voice output ............................................. 69
Sending a test sound to the speakers ................................................... 69
Glossary ........................................................................ 82
Specifications ............................................................... 83
DVD language code table ............................................ 84
Monitor setup ......................................................................... 70
Setting the monitor position .................................................................. 70
Image settings ....................................................................................... 71
Activating/deactivating the touch screen monitor .................................. 72
Setting the touch position ...................................................................... 73
13
13
03.02.2006, 8:32 Uhr
14
User notes
Thank you for choosing a Blaupunkt product. We hope you enjoy
using this new piece of equipment.
Please read these operating instructions before using the
equipment for the first time.
The Blaupunkt editors are constantly working on making the operating instructions clearer and easier to understand. However, if
you still have any questions on how to operate the device, please
contact your dealer or the telephone hotline for your country. You
will find the telephone number printed at the back of this booklet.
We provide a manufacturer guarantee for our products bought
within the European Union. Devices purchased outside the European Union are subject to the warranty terms published by our
respective regional agency.
You can view the guarantee conditions at www.blaupunkt.de or
ask for them directly at:
Blaupunkt GmbH
Hotline
Robert-Bosch-Str. 200
D-31139 Hildesheim
Please note that changes or modifications to the device that are
not explicitly authorised by the manufacturer void any warranty
claims.
14
Safety precautions
Observe all warnings, safety precautions and notes for service in
these operating instructions to extend the useful life of the device.
●
The device may only be operated with the recommended power supply of 12 V DC voltage.
●
Do not attempt to open or dismantle the device – danger of
electrical shock.
●
If the device is defective, return it to a local dealer or send it to
our customer service department.
●
Avoid using the device in an environment in which it is exposed to dust, dirt or humidity.
Risk of severe damage to the CD/DVD drive!
CD/DVD singles with a diameter of 8 cm and noncircular contoured CDs/DVDs (shape CDs) must not
be used. We accept no responsibility for any damage
to the CD/DVD drive that may occur as a result of the
use of unsuitable CDs.
To avoid damaging the drive, do not affix any labels
to the surface of the CD/DVD and do not use any protective film or stabiliser (commercially available as
accessory).
03.02.2006, 8:32 Uhr
User notes
Care instructions for CDs/DVDs
Not the following comments with respect to the read quality:
If a CD/DVD becomes soiled, never clean it in a circular motion;
instead, use a soft, lint-free cloth and wipe from the inside to the
outside. For extreme soiling, we recommend immersing the CD/
DVD in a solution with commercial liquid detergent. Once again,
please do not wipe the CD/DVD in a circular motion; instead,
always clean from the inside to the outside and let it dry.
Any soiling or damage of a CD/DVD can lead to read problems.
The severity of the read error is dependent upon the soiling as
well as the severity of the mechanical damage. Heavy scratches
cause read errors (data errors), which may cause the CD/DVD to
skip or hang. For this reason, always handle a CD/DVD with care
and always store it in its case.
Usable media
The Aspen/Chicago IVDM-7003 can be used to play DVDs, video CDs (VCD), super-video CDs (SVCD) and commercial audio
CDs and MP3 CDs with a diameter of 12 cm.
We also recommend treating the CD/DVD with care on either
side since the information layer of the CD/DVD is located immediately below the print layer (label side).
If possible, only grasp the CD/DVD at the edge.
Self-burnt storage media such as CD-Rs, CD-RWs and CD-Rs
with MP3 music files, VCDs, SVCDs and DVD-Rs can generally
be played. The various combinations of burners, burning software, blanks and ambient temperature inside the vehicle may
lead to problems with the device’s ability to play certain media.
Blaupunkt does not provide any guarantee for faultfree playback.
To ensure proper functioning of audio CDs, use only CDs with
the Compact-Disc logo. Copy-protected CDs can cause playback
problems. Blaupunkt cannot guarantee the proper functioning of
copy-protected CDs!
15
15
03.02.2006, 8:32 Uhr
16
User notes
Region code
License
The Aspen/Chicago IVDM-7003 and the DVDs are labelled with
the region code that is applicable for the pertinent country.
Manufactured under license of Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks of
Dolby Laboratories.
This product contains technologies that are copyright-protected
under certain US-American patents. The copyrights are property
of Macrovision Corporation and other copyright owners. The use
of this copyright-protected technology must be approved by Macrovision Corporation and is intended exclusively for private use
and other presentations in a limited scope, unless Macrovision
Corporation first issued a respective permission.
This device is permanently set to the region code that is valid for
the country in which it was sold.
Playing a DVD with a different region code is not possible.
Code
Region
1
North America, incl. the US and Canada
2
Japan, Europe (excl. Eastern Europe), Middle East,
South Africa
3
Korea and South-East Asia
Inserting batteries in the remote control
4
Oceania incl. Australia, New Zealand, Central and
South America
The remote control requires two AAA batteries for operation which
are part of the scope of delivery.
5
India, Eastern Europe, Africa, Russia
1.
Open the battery compartment at the back of the remote
control.
2.
Insert the battery with the correct polarity as displayed in
the battery compartment.
3.
Close the battery compartment.
6
China
All
regions
Used batteries do not belong in the household trash! Dispose of
used batteries in accordance with the legal regulations.
16
03.02.2006, 8:32 Uhr
Notes about these instructions
These instructions describe the functions of the Aspen/Chicago
IVDM-7003 and are intended to familiarise you with its operation.
Read these instructions before starting up the device.
To help you in quickly locating information, the following symbols
are used in these instructions:
Safety and warning notes contain important information
concerning the safe usage and point to accident sources.
1.
Marks instructional steps to be performed to reach the
goal of an action.
✔
Devise responses that must follow an action are marked
like this.
Note: Text marked by “Note” provides additional
information about a topic.
The monitor views shown in these instructions are intended to
support the explanation. The actual monitor displays may differ.
If required, the corresponding illustrations of the device display
are shown with retracted monitor.
17
17
03.02.2006, 8:32 Uhr
18
Theft protection
The device is equipped with a detachable control panel (fliprelease panel) as theft protection and a four-digit device code.
✔
Detachable control panel
Protect your device against theft by taking the control panel with
you whenever you leave your vehicle. Do not leave the control
panel inside the vehicle - not even in a hiding place. The device
is worthless to a thief without this control panel.
After removing the control panel from the device, device
switches off after approx. 30 seconds. All the current
settings are saved. Any inserted CD/DVD remains in
the device.
Attaching the control panel
1.
Push the control panel into the guides of the device from
the right to the left.
The structural design of the control panel allows for simple handling of the control panel during removal and attaching.
SR
C
NA
VI
Removing the control panel
button.
1.
Press the
✔
The locking mechanism of the control panel is unlocked.
2.
Pull the control panel straight out of the device and to
the right.
DIS
VO
L
CH
ICA
GO
IV
1
-D
IS
C
2
DI
SC
+
3
ZO
DM
-700
2
OM
4
RP
T
5
MIX
6
SCAN
BS
BN
SR
M
D
TU
NE
C
NA
VI
2.
Notes: If the device was switched on while removing
the control panel, it does not automatically switch back
on after attaching it.
DIS
VO
L
CH
ICA
GO
1
-D
IS
C
2
DI
SC
IVD
M-7
00
+
2
3
ZO
OM
4
RP
T
5
MIX
6
SCAN
BS
BN
Push the right side of the control panel into the device until
it clicks into place.
18
M
D
TU
NE
Never drop the control panel. Never expose the control panel to direct sunlight or other heat sources.
Store the control panel in the supplied case.
03.02.2006, 8:32 Uhr
Theft protection
Activating the device code
Switching on coded devices after a voltage interruption
In addition to a detachable control panel, the device is equipped
with a four-digit device code. The device code is set to 0000 at
the factory. With this setting, the coding is not active and the device can be switched on without code query after a voltage interruption.
If a coded device is switched on after disconnecting the battery
voltage, e.g. in case of a repair to the vehicle, the code query
appears.
To activate the coding of your device, you must enter a freely
selectable code. How to change the code is described in the chapter “Setup menu” under “Changing the password”.
Note: Record your personal code and keep it in a safe
place. If you ever forget the code, the device cannot
be switched back on after a voltage interruption. In
this case, the device must be decoded by returning it
to a local dealer or sending it to our customer service
department.
PASSWORD
1.
Enter the four-digit code using the number buttons 0 to 9
on the remote control.
button to correct any incorrect entries.
2.
Press the
3.
Confirm the entry with the ENTER button.
✔
The device switches on.
19
19
03.02.2006, 8:32 Uhr
20
Introduction
This chapter contains a description of the most important basic
functions.
Note: The monitor is automatically opened at switchon if this function was activated in the setup menu.
For further details, read the section “Configuring the
monitor position” in the chapter “Setup menu”. If the
monitor was closed at switch-off, it remains in this
position after switch-on.
Operating options
Several options are available to operate the Aspen/Chicago IVDM7003.
The buttons of the remote control allow you to operate all the
functions of the device. The buttons on the front of the device
allow you to operate the most important functions.
92 94 100 104
RADIO
STATIOn
R·D·S AF TA REG
1. Radio 21
In addition, the Aspen/Chicago IVDM-7003 features a touch
screen monitor that responds to touch. Operating the device is
done by using the visible buttons in the individual operating modes
and via the buttons on the touch screen menu. Touch the center
of the screen to call up the touch screen menu. If no additional
operation is performed, the touch screen menu is hidden again
after approx. 30 seconds.
FM1
2. NDR 2
TP
Radio 21
3. Antenne
4. ffn
5. 89.0 RTL
6. N–JOY
Note: Operating the device by means of the touch
screen monitor is only possible if this function was
activated in the setup menu. For further details, read
the section “Activating/deactivating the touch screen
monitor” in the chapter “Setup menu”.
13:05
R• D• S
AF TP
RADIO 21
TP
P
1
Radio display with closed monitor
Switching the device on/off
1.
To switch the Aspen/Chicago IVDM-7003 on, press the
button on the device or the
/ POWER button on the
remote control.
✔
The devices switches on and the playback of the previously set operating mode starts.
20
1.
To switch it off, press and hold the
button on the device
/ POWER button
for more than 2 seconds or press the
of the remote control.
✔
The device switches off.
03.02.2006, 8:32 Uhr
Introduction
Inserting a CD/DVD
Ejecting a CD/DVD
1.
Push the CD/DVD into the CD/DVD tray with the printed
side facing up.
1.
✔
The drive automatically pulls in the CD/DVD.
Press the
button on the device.
Note: You must not hinder or assist the drive as it
draws in the media.
EJECT
LOADING
EJECT
Eject display with closed monitor
LOADING
Load display with closed monitor
✔
✔
2.
The CD/DVD is ejected.
Carefully remove the CD/DVD.
Note: If the CD/DVD is not removed, it is automatically
drawn in again after approx. 10 seconds.
The CD/DVD is loaded and playback starts.
21
21
03.02.2006, 8:32 Uhr
22
Introduction
Adjusting the volume
Activating mute
1.
On the device: To increase the volume, press the
VOL + button.
To decrease the volume, press the VOL - button.
1.
On the remote control: To increase the volume, press the
button.
VOL
button.
To decrease the volume, press the VOL
✔
Playback is muted.
✔
button on the device flashes and the bottom of the
The
monitor displays “MUTE” B.
✔
On the device: Briefly press the
During the adjustment, the current value is displayed at
the bottom of the monitor A.
92 94 100 104
RADIO
STATIOn
R·D·S AF TA REG
1. Radio 21
92 94 100 104
RADIO
FM1
STATIOn
2. NDR 2
R·D·S AF TA REG
1. Radio 21
button.
On the remote control: Press the MUTE button.
TP
Radio 21
4. ffn
3. Antenne
5. 89.0 RTL
4. ffn
6. N–JOY
B
5. 89.0 RTL
6. N–JOY
VOL
AF TP
VOL 12
TP
A
Cancelling mute
button again to cancel mute.
1.
Press the
✔
Mute is cancelled.
Volume display with closed monitor
Radio 21
3. Antenne
FM1
2. NDR 2
R•D•S
TP
22
03.02.2006, 8:32 Uhr
Introduction
Closing/opening the monitor
1.
On the device: Press the
Selecting the signal source
/ CLOSE button.
1.
On the remote control: Press the OPEN/CLOSE button.
✔
The monitor is closed or opened.
Setting the monitor tilt
1.
On the monitor: Touch the center of the monitor to call up
the touch screen menu. Touch the button of the desired
signal source A.
DVD
On the remote control: Press the TILT - button to tilt the
monitor forward by one increment.
Press the TILT + button to tilt the monitor backward by
one increment.
RADIO
CD - C
A
AUX
UX 1
1. Radio 21
FM1
2. NDR 2
RADIO
NAVI
NA
A
TP
Radio 21
3. Antenne
BAND
4. ffn
92 94 100 104
A
AUX
UX 2
R·D·S AF TA REG
BSM
STATIOn
5. 89.0 RTL
R·D·S AF TA REG
1. Radio 21
TP
6. N–JOY
FM1
2. NDR 2
Radio 21
Sound
Setup
Rear
Disp
PTY
R·D·S
MONITOR TILT
–2 –1
3. Antenne
0
+1 +2
On the device and on the remote control: Press the
SRC button until the desired signal source appears
on the monitor.
4. ffn
5. 89.0 RTL
Available signal sources:
6. N–JOY
13:05
Note: To tilt the monitor horizontally to the front, press
the DIS / FLIP button on the device. Press the button
again to return the monitor to its original position.
CD/MP3/DVD > RADIO > CD-C > AUX1 > AUX2 > (IVSC) > NAVI
Note: The selectable signal sources are dependent
upon the connected devices and the settings in the
setup menu.
23
23
03.02.2006, 8:32 Uhr
24
Introduction
Sound settings
Selecting and setting sound effects:
The following sound settings are possible:
On the monitor:
Aspen IVDM-7003
1.
Bass
-7 … -1 < 0 > +1 … +7
Touch the center of the monitor to call up the touch screen
menu.
2.
Touch the
✔
The sound effects menu appears on the display.
Treble
-7 … -1 < 0 > +1 … +7
Balance (left/right volume distribution)
L15 … L1 < 0 > R1 … R15
Downmix
OFF > Stereo > Lt/Rt
Chicago IVDM-7003
ProLogic 2
OFF > ProLogic > Music > Movie > Matrix
Fader (front/rear volume distribution)
R15 … R1 < 0 > F1 … F15
Note: For additional details about sound settings, refer
to the section “Audio setup” in the chapter “Setup
menu”.
24
ProLogic2
OFF
SFC
OFF
DownMIX
OFF
ProLogic
Studio
Music
Hall
Stereo
Church
Lt/Rt
BALANCE
+0
FADER
+0
NEXT
EXIT
SFC (environment audio effects)
OFF > Studio > Hall > Church > Stadium > Movie > Club
Balance (left/right volume distribution)
L15 … L1 < 0 > R1 … R15
button.
Audio Effect Control
Fader (front/rear volume distribution)
R15 … R1 < 0 > F1 … F15
Downmix
OFF > Stereo > Lt/Rt
Sound
Chicago IVDM-7003
3.
Select the sound effect to be set by touching it.
4.
Perform the setting by repeatedly touching the left or right
area of the scale or by touching the desired setting.
or
button displays additional setTouching the
ting options.
5.
Touch the
6.
To perform additional settings, repeat steps 3 - 5.
7.
Touch the
EXIT
EXIT
button to confirm the setting.
button to hide the sound effects menu.
03.02.2006, 8:32 Uhr
Introduction
On the remote control:
Switching the Downmix mode on/off
1.
Press the SOUND / DSP button.
✔
The sound effects menu appears on the display.
If the Downmix mode is activated, the multi-channel surround signal is transferred into a conventional stereo signal.
ProLogic2
OFF
SFC
OFF
DownMIX
OFF
ProLogic
Studio
1.
On the remote control: Press the DOWNMIX button to activate the downmix mode.
2.
Press the button again to deactivate the downmix mode.
Music
Hall
Stereo
Selecting the display illumination colour
Church
The following colours are available for the display illumination of
the device:
Lt/Rt
BALANCE
+0
FADER
+0
Turquoise > Red > Violet > Yellow > White > Blue > Green >
1.
NEXT
EXIT
On the device: Hold the DIS / FLIP button pressed until
the colour changes. Repeat the process until the desired
colour is set.
On the remote control: Press the LCD button repeatedly
until the desired colour is set.
Chicago IVDM-7003
2.
Press the ENTER button.
3.
Select the sound effect to be set with the
4.
Select the desired setting with the
5.
To perform additional settings, repeat steps 3 - 4.
or
or
button.
button.
6.
Touch the SETUP button to hide the sound effects menu.
✔
The settings are automatically saved.
25
25
03.02.2006, 8:32 Uhr
26
Introduction
Show/hide the image of a back-up camera
Automatic through connection of telephone calls
A back-up camera (optional equipment) can be connected to the
Aspen/Chicago IVDM-7003. The camera image is automatically
displayed when the reverse gear is selected if the back-up camera was connected to the device as described in the installation
instructions. In the setup menu you can configure whether you
want to display the image of the back-up camera as horizontal
mirror. That gives the same impression as a rear-view mirror. For
further details, read the section “Selecting the external signal
source” in the chapter “Setup menu”.
If your Aspen/Chicago IVDM-7003 is connected to a hands-free
system for cell phones, the active signal source is muted if a telephone call arrives and the call is played back using the car sound
system. For this purpose, the hands-free system must be connected to the device as described in the installation instructions.
Note: To manually display the camera image, press
the REAR button of the remote control or touch the
Rear
button on the touch screen menu. Press the
button again or touch the center of the monitor to hide
the camera image again.
26
Traffic announcements and acoustic driving suggestions from a
connected navigation system are not connected through during a
telephone call.
You can change the volume during a telephone call.
1.
On the device: Use the VOL - / + buttons.
On the remote control: Use the VOL
/
buttons.
If the volume is changed during a call, this value remains valid
until the volume is changed again during a call.
03.02.2006, 8:32 Uhr
Radio mode
Radio menu
92 94 100 104
Touch screen menu in radio mode
RADIO
STATIOn
Info
R·D·S AF TA REG PTY TP
1. Radio 21
FM1
2. NDR 2
Radio 21
A
DVD
B
C
RADIO
CD - C
A
AUX
UX 1
A
AUX
UX 2
NAVI
NA
R·D·S AF TA REG
1. Radio 21
FM1
2. NDR 2
A
TP
Radio 21
B
3. Antenne
3. Antenne
4. ffn
4. ffn
5. 89.0 RTL
5. 89.0 RTL
D
6. N–JOY
6. N–JOY
E
E
13:05
A
Display: programme type, if selected
B
Display: RDS functions
Button: call up the menu for RDS settings
C
Display: waveband/memory bank and station name/
frequency
Button: Select waveband/memory bank
D
Display: time
E
Display: list of stored stations
Button: call up stored stations
D
Sound
M
BAND
Setup
Rear
L
K
Disp
J
PTY
H
BSM
C
R·D·S
G
F
A
B
Selecting the waveband/memory bank
C
Automatically storing stations
D
Automatic station search up/down
E
Manual station search up/down
F
Exit the touch screen menu
G
Call up the menu for RDS settings
H
Call up a list with programme types
I
Change the wallpaper
K
L
Call up the setup menu
M
Call up the menu for sound settings
27
27
03.02.2006, 8:32 Uhr
28
Radio mode
Switching to radio mode
On the monitor:
1.
1.
Touch the
✔
The RDS menu is displayed at the bottom of the monitor.
button to switch
the touch screen menu. Touch the
to radio mode.
RADIO
On the device or on the remote control: Press the SRC
button until the radio menu is displayed.
✔
92 94 100 104
AF TP
RADIO 21
F1 10580
button on the touch screen menu.
RADIO
STATIOn
R·D·S AF TA REG
1. Radio 21
The station selected last is playing.
R•D•S
R·D·S
FM1
2. NDR 2
TP
P
1
P
1
TP
Radio 21
3. Antenne
4. ffn
OK
5. 89.0 RTL
Display with closed monitor: RDS functions, station
name or waveband/memory bank and frequency, memory location
6. N–JOY
RDS Set
Flip Item
Change Value
ON
Switching RDS (Radio Data System) on/off
RDS is a service of the radio stations that offers more comfort for
listening to the radio on the FM waveband. The radio stations
broadcast additional information to the programme, such as the
station name. The station name is displayed on the monitor or
the device display as soon as it is received.
Note: The RDS function must be activated before the
advantages of RDS can be used.
28
2.
Select the “RDS Set” menu entry with the
3.
Touch the
(OFF) RDS.
or
4.
Touch the
button to hide the RDS menu.
OK
or
button.
button to activate (ON) or deactivate
1.
Press the RDS / MENU button.
✔
2.
Select the “RDS Set” menu entry with the
3.
Press the or
(OFF) RDS.
4.
Press the RDS / MENU button to hide the RDS menu.
or
button.
03.02.2006, 8:32 Uhr
Radio mode
Switching the RDS function AF (Alternate Frequency) on/off
If the RDS function AF (Alternate Frequency) is activated, the
device automatically tunes into the best receivable frequency for
the station that is currently set.
On the monitor:
1.
Touch the R·D·S button or touch the
touch screen menu.
✔
2.
Select the “AF Set” menu entry with the
3.
or
Touch the
(OFF) the AF function.
4.
Touch the
OK
R·D·S
button on the
or
button.
1.
✔
2.
Select the “AF Set” menu entry with the
3.
Press the or button to activate (ON) or deactivate
(OFF) the AF function.
4.
or
button.
Note: The AF function can also be switched on/off by
using the AF / SUBTITLE button. If the function is
activated, the monitor displays the AF symbol.
Switching the RDS function REG (Regional Programmes)
on/off
At certain times, some RDS stations divide their programme into
regional programmes providing different content. If the RDS function REG (Regional Programmes) is activated, it prevents the
device from switching to a different regional programme when it
is searching for the best receivable frequency.
On the monitor:
1.
touch screen menu.
✔
2.
Select the “REG Set” menu entry with the
3.
or
Touch the
(OFF) the REG function.
4.
Touch the
OK
R·D·S
button on the
or
button.
1.
✔
or
button.
2.
Select the “REG Set” menu entry with the
3.
(OFF) the REG function.
4.
Note: The REG function can also be switched on/off
by using the REG / ANGLE button. If the function is
activated, the monitor displays the REG symbol.
29
29
03.02.2006, 8:32 Uhr
30
Radio mode
Selecting the waveband/memory bank
Automatic station search
This device can receive programmes broadcast over the FM and
AM wavebands. Three memory banks are available for the FM
waveband and one memory bank for the AM waveband. Six
stations can be stored in each memory bank.
1.
Selecting the memory bank or waveband:
✔
1.
On the monitor: Touch the
or
button repeatedly or
touch the BAND button repeatedly on the touch screen
menu.
On the device or on the remote control: Press the
button.
1.
The current memory bank or the current waveband and
the station set last are displayed on the monitor A.
RADIO
or
The radio tunes into the next receivable station.
on the touch screen menu.
or
On the remote control: Press the
edly.
✔
STATIOn
button repeatedly
or
button repeat-
The frequency is changed in increments.
This allows you to set a station with a known frequency:
R·D·S AF TA REG
1. Radio 21
FM1
2. NDR 2
TP
Radio 21
3. Antenne
4. ffn
1.
On the device: For coarse tuning, hold the or button
pressed until the frequency of the desired station is
reached.
2.
For fine tuning, press the
of the station is displayed.
A
5. 89.0 RTL
6. N–JOY
13:05
button on the
You can also search for stations manually.
On the remote control: Press the BAND button repeatedly.
92 94 100 104
or
Manual station search
On the device: Press the BND / BSM button repeatedly.
✔
touch screen menu.
30
03.02.2006, 8:32 Uhr
or
until the exact frequency
Radio mode
Storing stations manually
✔
18 memory locations are available in the FM waveband (6 on
each memory bank) and 6 memory locations in the AM waveband.
The device changes to memory bank FM3, if necessary,
and automatic storing of stations starts.
✔
After the process is completed, each stored station is
played for approx. 3 seconds. The station name is also
stored if the RDS function is activated.
1.
Select the memory bank FM1, FM2, FM3 or the waveband
MW.
2.
Tune into the desired station.
3.
On the monitor: Touch the button of the station list for approx. 2 seconds where you want to store the tuned station.
On the device: Hold the station button (1 to 6) of the memory location pressed for approx. 2 seconds where you
want to store the tuned station.
✔
Note: For stations with changing RDS displays, it is
possible that currently transmitted commercials or
other information is stored instead of the station name.
Calling up stored stations
1.
Select the memory bank or waveband.
2.
On the monitor: Touch the memory location of the desired
station in the station list.
If the station is stored, the frequency or the station name is
displayed next to the selected number in the station list.
Any existing entry is overwritten.
On the device or on the remote control: Select the desired
memory location by using the station buttons 1 to 6.
✔
The desired station is playing.
Automatically storing stations
You can automatically store the six FM stations offering the strongest reception in the region. These stations are stored on memory
bank FM3.
Note: Any stations that were previously stored in this
memory bank are replaced in the process.
1.
screen menu.
BSM
button on the touch
On the device: Hold the BND / BSM button pressed for
longer than 2 seconds.
31
31
03.02.2006, 8:32 Uhr
32
Radio mode
Station search by programme type
Some RDS stations broadcast information about the type of programme broadcast (e.g. news, sports, rock, pop). By using this
information, the device perform a directed search for stations of
a certain programme type.
Selecting the programme type:
1.
screen menu.
✔
Seek tuning starts and the next station with the selected
programme type is tuned.
✔
The PTY symbol and the selected programme type are
displayed on the monitor A.
button on the touch
PTY
92 94 100 104
On the remote control: Press the PTY / ZOOM button.
✔
Note: If “All” is selected, the PTY function is deactivated.
RADIO
STATIOn
Info
R·D·S AF TA REG PTY TP
1. Radio 21
The available programme types appear on the monitor.
FM1
2. NDR 2
NDR Info
3. Antenne
DVD
RADIO
CD - C
AUX
AUX 1
A
AUX
UX 2
NAVI
NA
R·D·S AF TA REG
PTY Search
FM1
All
TP
Radio 21
4. ffn
5. 89.0 RTL
6. N–JOY
News
BAND
Current Affairs
Information
Sport
Sound
2.
Setup
Rear
Disp
PTY
13:05
BSM
R·D·S
Note: If the device does not locate a corresponding
station, the PTY function is deactivated and the station set last is played.
On the monitor: Select the desired programme type with
or
button and touch the button of the selected
the
programme type.
On the remote control: Select the desired programme type
or
button and press the ENTER button.
with the
32
03.02.2006, 8:32 Uhr
A
A
Radio mode
Traffic information stations
Switching traffic announcement priority on/off
Traffic information stations are RDS stations broadcasting traffic
announcements. If you are listening to a traffic information station,
the TP symbol is displayed on the monitor A.
The priority for traffic announcements is activated if the display
shows the TA symbol B.
92 94 100 104
92 94 100 104
RADIO
RADIO
STATIOn
STATIOn
R·D·S AF TA REG
1. Radio 21
R·D·S AF TA REG
1. Radio 21
TP
A
FM1
2. NDR 2
FM1
2. NDR 2
TP
B
Radio 21
Radio 21
3. Antenne
3. Antenne
4. ffn
4. ffn
5. 89.0 RTL
5. 89.0 RTL
6. N–JOY
6. N–JOY
13:05
13:05
On the monitor:
The Aspen/Chicago IVDM-7003 is equipped with a RDS-EON
receiving unit. EON stands for Enhanced Other Network.
1.
touch screen menu.
EON allows for listening to traffic announcements even if the tuned
station does not broadcast traffic information. In the event of a
traffic announcement, the device switches within a station chain
to the traffic information station of station chain that is connected
via EON.
✔
2.
Select the “TA Set” menu entry with the
3.
Touch the
or
(OFF) the priority for traffic announcements.
After the traffic announcement, the device switches back to the
previously played station.
4.
Touch the
OK
R·D·S
button on the
or
button.
33
33
03.02.2006, 8:32 Uhr
34
Radio mode
Cancelling the current traffic announcement
1.
✔
A current traffic announcement can be cancelled if you do not
want to listen to it.
2.
Select the “TA Set” menu entry with the
3.
(OFF) the priority for traffic announcements.
4.
or
button.
Note: The priority for traffic announcements can also
be switched on/off by using the TA / AUDIO button.
If he priority is activated, the monitor displays the TA
symbol.
1.
On the device: During a traffic announcement, press the
button.
✔
The current announcement is cancelled. The priority for
traffic announcement remains activated.
Note: A traffic announcement, during which the device
switched to the traffic information station connected
via EON, cannot be cancelled.
Setting the volume for traffic announcements
In radio mode, the traffic announcement is played with the volume
set for traffic announcements.
In other operating modes, the playback is muted during a traffic
announcement and the announcement is played with the set value.
Note: Traffic announcements are not played if mute is
activated or during a telephone call.
You can change the volume during a traffic announcement.
1.
/
buttons.
If the volume is changed during a traffic announcement, this value
remains valid until the volume is changed again during a traffic
announcement.
34
03.02.2006, 8:32 Uhr
DVD operation
DVD menu
A
B
Touch screen menu in DVD mode
C
DVD
DVD
TITLE
02
CHAP
007
TImE
RADIO
CD - C
A
AUX
UX 1
A
AUX
UX 2
NAVI
NA
A
00:16’35
B
C
D
E
Sound
Angle
OFF
2 English
F
E
M
G
A
B
C
D
E
F
G
Display: Current title
Button: Direct selection of title
Display: Current chapter
Button: Direct selection of chapter
Display: Expired playing time
Button: Exit DVD menu
Display: Playback language
Button: Select playback language
Display: Subtitle language
Button: Select subtitle language
Display: Camera perspective
Button: Change camera perspective
Setup
Rear
L
K
Track
J
H
Pict
G
F
D
A
B
C
D
E
F
G
H
I
K
L
M
Start/interrupt playback
Exit playback
Chapter selection up/down
Call up the menu for image format, zoom, repeat and
image settings
Call up the DVD menu
Call up the controls for the DVD main menu
35
35
03.02.2006, 8:33 Uhr
36
DVD operation
Switching to DVD mode
1.
Starting playback
button.
DVD
button until the DVD mode is displayed as the signal
source.
✔
After an inserted DVD is loaded, either the DVD main menu is
displayed or the playback starts. This action is dependent upon
the DVD.
1.
The DVD menu is briefly displayed.
Note: When you insert a DVD, the device automatically switches to DVD mode. For safety reasons, the
image playback of a DVD only operates if the vehicle
is standing and the hand brake is applied. While
driving, only the sound playback is possible. The
monitor displays a warning. The image playback for
passengers in the rear seats continues while driving
if a monitor is connected.
screen menu.
button on the touch
button.
✔
/ PLAY/PAUSE button.
The DVD starts playing.
Interrupting playback (freeze frame)
Playback can be interrupted and restarted.
1.
T02 C007
button on the touch
screen menu. To continue playback, touch the button
again.
press the button again.
Display with closed monitor: Dolby digital, title, chapter.
Press the DIS / FLIP button repeatedly to display
additional information.
button. To continue playback,
To continue playback, press the button again.
Exiting playback
1.
screen menu.
button on the touch
36
03.02.2006, 8:33 Uhr
button.
DVD operation
Selecting a chapter
DVD
A DVD title can be divided into several chapters.
TITLE
_
CHAP
007
TImE
00:16’35
Selecting the next chapter:
1.
touch screen menu.
button repeatedly on the
repeatedly.
button
Selecting the previous chapter:
1.
touch screen menu.
repeatedly.
Angle
button
or
Note: For a fast chapter selection, hold the
button of the remote control pressed until the fast
selection for the next or previous chapter starts.
OFF
1
2
3
4
5
6
7
8
9
Menu
Men
0
OK
2 English
3.
Touch the
4.
Enter the desired title or chapter number with the buttons
0 to 9 and confirm the entry with the OK button.
✔
Playback is continued at the selected position.
CHAP
button for direct selection of a chapter.
Direct selection of a title or chapter
A DVD is divided into different titles and chapters which can be
directly selected.
1.
Press the GOTO button.
✔
The DVD menu is displayed. A cursor is displayed instead
of the title number.
2.
Press the GOTO button again for the direct selection of a
chapter.
3.
Enter the desired title or chapter number with the number
buttons 0 to 9 and confirm the entry with the ENTER button.
✔
Playback is continued at the selected position.
On the monitor:
1.
Touch the
✔
The DVD menu is displayed.
2.
Touch the
✔
A cursor is displayed instead of the title number and buttons with numbers are displayed.
Track
TITLE
button.
37
37
03.02.2006, 8:33 Uhr
38
DVD operation
Fast search
To search for a specific section during the playback of a DVD,
you can use the fast search function.
1.
✔
1.
or
button on the
touch screen menu repeatedly for fast forward or reverse
search.
forward or reverse search.
2.
You found the desired position and want to continue the playback with regular speed.
or
button for fast
screen menu.
button on the touch
Selecting the playback language
On the monitor:
Repeatedly touching the button or pressing the button
changes the search speed (2x, 4x, 6x, 8x).
The selected speed is displayed on the monitor A.
1.
Touch the
✔
2.
To select the desired playback language, touch the
button once or several times.
✔
The playback language is changed.
Track
x2
A
1.
To select the desired playback language, press the
TA / AUDIO button once or several times.
✔
The playback language is changed.
Note: Sound and subtitle are not being while fast
searching forward or back.
38
03.02.2006, 8:33 Uhr
DVD operation
Selecting the subtitle language
Switching the image format
On the monitor:
1.
1.
Touch the
✔
2.
To select the desired language of the subtitles or to combutton once or
pletely hide the subtitles, touch the
several times.
Track
Pict
button on the touch
screen menu. To toggle between wide image 16:9 (WIDE)
Wide butand normal image 4:3 (NORMAL), touch the
ton.
On the remote control: To toggle between wide image 16:9
(WIDE) and normal image 4:3 (NORMAL), press the WIDE
button.
1.
To select the desired language of the subtitles or to
completely hide the subtitles, press the AF / SUBTITLE
button once or several times.
Enlarging an image area (Zoom)
An image area can be enlarged using different zoom levels.
1.
Repeating a chapter or title
The Repeat function is used to repeatedly play the current chapter or the current title.
On the device: Press the 3 / ZOOM button once or several
times.
The selected Repeat function is displayed on the monitor.
1.
REPEAT
(repeat a chapter)
REPEAT
(repeat a title)
Pict
button on the touch
screen menu and then touch the Repeat button once or
several times.
On the device: Press the 4 / RPT button once or several
times.
Pict
button on the touch
Zoom button once or
screen menu and then touch the
several times.
On the remote control: Press the PTY / ZOOM button once
or several times.
✔
Every time you touch or press the button, the central image area is enlarged by one level (1.5x, 2x, 3x, normal).
The selected zoom level is displayed on the monitor.
2.
On the remote control: After setting the desired zoom,
/
you can move the image area with the buttons
and / .
On the remote control: Press the REPEAT button once or
several times.
39
39
03.02.2006, 8:33 Uhr
40
DVD operation
Image settings
5.
During playback, you can adjust brightness, colour, contrast, tint
and dimmer.
EXIT button to end the setting and call up the
Use the
menu for the image settings again.
6.
Touch the
1.
Pict
button on the touch
Scrn button.
✔
The menu for the image settings is displayed.
2.
Select “Brightness”, “Colour”, “Contrast”, “Tint” or “Dimmer”
by touching it.
✔
The image of the DVD and a scale for the setting are
displayed.
EXIT
button to exit the menu.
Selecting the camera perspective (Angle)
If scenes with different camera perspectives are stored on the
DVD, you can change the camera perspective during playback.
On the monitor:
1.
Touch the
✔
2.
To select from the available camera perspectives, touch
the Angle button once or several times.
Track
1.
Brightness
To select from the available camera perspectives, touch
the REG / ANGLE button once or several times.
+0
EXIT
3.
Repeatedly touch the left or right area of the scale to
perform the setting.
4.
Use the
settings.
Brightness
button to perform additional image
40
03.02.2006, 8:33 Uhr
DVD operation
Calling the DVD main menu
The main menu is stored on the DVD. The selection options offered by the main menu are dependent upon the respective DVD.
The main menu of a DVD can offer the following:
●
You can select from different languages for the playback or
for the subtitles.
●
A movie is divided into several sequential chapters. You can
select a chapter and directly start the playback.
On the monitor:
1.
✔
Touch the
then touch the
Menu
button on the touch screen menu and
button.
The DVD main menu is displayed.
Note: If the buttons cover menu entries of the main
or
button to change the position
menu, use the
of the buttons.
2.
/
/
/
Use the
individual menu entries.
buttons to select from the
3.
To confirm a menu entry, touch the
4.
To hide the buttons, touch the
OK
button.
button.
1.
✔
The DVD main menu is displayed.
2.
/
/ / buttons to select from the
Use the
individual menu entries.
3.
To confirm a menu entry, press the ENTER button.
41
41
03.02.2006, 8:33 Uhr
42
Audio CD mode
Audio CD menu
Touch screen menu in Audio CD mode
A
AUDIO
- CD
Audio–CD
K
TRACK
01
TImE
00:02’35
NORMAL
No Title
1 Track 1
B
A
AUX
UX 1
A
AUX
UX 2
NAVI
NA
NORMAL
B
2 Track 2
3 Track 3
5 Track 5
TEXT
13:05
C
3 Track 3
E
F
G
4 Track 4
D
5 Track 5
E
Sound
L
Setup
Rear
K
J
Disp
H
Func
G
F
A
Display: Currently playing track
B
A
C
Display: Playback mode (Normal, Repeat, Scan, Mix)
B
D
Display: Playback, pause, fast scan
Button: Interrupt/start playback
C
Exit playback
D
Track selection up/down
E
Button: Forward/reverse track selection
E
F
Display: Graphical equaliser (Chicago IVDM-7003 only)
F
G
Display: Time
G
Call up the menu for Mix, Repeat, Scan function
H
Display: CD text information (if available)
H
J
Display: Track list
I
K
Display: Name of CD (if CD text is available)
K
L
A
1 Track 1
4 Track 4
H
CD - C
No Title
C
D
2 Track 2
J
RADIO
42
03.02.2006, 8:33 Uhr
Audio CD mode
Activating the audio CD mode
1.
Exiting playback
button.
1.
AUDIO
- CD
button until the Audio CD menu is displayed.
✔
The track selected last is playing.
Note: When you insert an audio CD, the device automatically switches to Audio CD mode. Track 1 of the
inserted CD is playing.
Selecting the next track:
1.
1.
button or touch the
button on the touch screen menu. To continue playback,
touch the button again.
/ PLAY/PAUSE
button. To continue playback, press the button again.
button repeatedly or touch
button repeatedly on the touch screen menu.
the
repeatedly.
-
button.
Selecting tracks
button
Selecting the previous track:
1.
Interrupting playback (pause)
button on the touch
T02-0248
Display with closed monitor: Track, playing time
screen menu.
button repeatedly on the touch screen menu. If
the
you touch the button once, the current track will be played
again from the beginning.
button repeatedly. If you press the button once, the current
track will be played again from the beginning.
Note: For a fast track selection, hold the or button
of the remote control pressed until the fast selection
for the next or previous track starts.
43
43
03.02.2006, 8:33 Uhr
44
Audio CD mode
Fast search
To search for a specific section during the playback of a track,
you can use the fast scan function.
1.
✔
1.
or
button on the
search.
2.
or
TRACK
01
TImE
/ PLAY/PAUSE
Note: When the start/end of the track is reached, the
fast scan automatically ends.
Repeating tracks (Repeat)
The selected speed is displayed on the monitor A.
Audio–CD
button on the touch
button.
button for fast
changes the search speed (1.5x, 2x, 3x, 4x).
screen menu.
The Repeat function repeats the current track until this function
is deactivated.
1.
00:02’35
Func button on the touch
screen menu and then touch the Repeat button.
NORMAL
No Title
x2
1 Track 1
On the device: Press the 4 / RPT button.
A
On the remote control: Press the REPEAT button.
✔
2 Track 2
Display on the monitor:
REPEAT
.
3 Track 3
-
T02-0248
4 Track 4
Repeat display with closed monitor
5 Track 5
TEXT
RPT
13:05
44
If you want to cancel the repeat function,
1.
Touch the button again or press the button again.
✔
03.02.2006, 8:33 Uhr
NORMAL
.
Audio CD mode
Random track play (MIX)
Scanning all tracks (Scan)
The Mix function plays the tracks of a CD in random order.
The Scan function plays all the tracks of the CD in sequential
order for approx. 10 seconds each.
1.
Mix
button.
+
1.
On the device: Press the 5 / MIX button.
On the device: Press the 6 / SCAN button.
On the remote control: Press the MIX button.
✔
MIX
Scan button.
On the remote control: Press the SCAN button.
.
✔
MIX
SCAN
.
T01-0002
-
-
T02-0248
Mix display with closed monitor
SCAN
Scan display with closed monitor
If you want to cancel the Mix function,
1.
✔
NORMAL
.
If you want to cancel the Scan function,
1.
✔
NORMAL
.
45
45
03.02.2006, 8:34 Uhr
46
CD-changer mode
CD changer menu
Touch screen menu in CD changer mode
A
DVD
CD–C
TRACK
TImE
01
00:00’35
NORMAL
1. TRACK 1
CD1
2. TRACK 2
B
RADIO
CD - C
A
AUX
UX 1
A
AUX
UX 2
CD1
2. TRACK 2
B
3. TRACK 3
E
F
3. TRACK 3
H
5. TRACK 5
6. TRACK 6
5
5. TRACK 5
D
6. TRACK 6
5
E
Sound
13:05
C
4. TRACK 4
4. TRACK 4
Setup
Rear
K
J
Disp
Func
G
L
H
G
F
A
Display: Currently playing track
B
A
C
B
D
C
Exit playback
D
Track selection up/down
E
Display: Currently playing CD
Button: Select CD
E
F
F
Button: Forward/reverse track selection
G
G
Display: Time
H
H
Display: Track list of currently playing CD
I
K
L
A
NORMAL
1. TRACK 1
C
D
NAVI
NA
46
03.02.2006, 8:34 Uhr
CD-changer mode
CD changers
The following Blaupunkt CD changers can be connected: CDC A03, CDC - A08 and IDC - A09.
1.
Notes: How to fill the magazine with CDs and insert
the magazine in the changer is described in the instructions of your CD changer.
If the magazine was newly inserted, all CDs in the
magazine are loaded once (magazine scan). Playback
is not possible during this time.
Activating the CD changer mode
1.
/ PLAY/PAUSE
Exiting playback
button.
1.
CD - C
button until the CD changer menu is displayed.
✔
button or touch the
The track selected last is playing.
-
T02-0248
screen menu.
button on the touch
button.
Selecting CDs
DISC
8
Selecting the next or previous CD:
1.
Display with closed monitor: Track, playing time,
CD number
times.
or
button once or several
On the device: Press the 1 / -DISC or 2 / DISC+ button
once or several times.
several times.
✔
or
button once or
The selected CD is loaded and playback starts with track 1.
47
47
03.02.2006, 8:34 Uhr
48
CD-changer mode
Selecting tracks on the currently playing CD
Repeating tracks (Repeat)
Selecting the next track:
The Repeat function is used to repeatedly play the current track
or the current CD.
the
repeatedly.
button
Selecting the previous track:
1.
REPEAT
(repeat a track)
REPEAT
(repeat a CD)
NORMAL
the
If you touch the button once, the current track will be
played again from the beginning.
button repeatedly. If you press the button once, the
current track will be played again from the beginning.
Note: For a fast track selection, hold the or button
of the remote control pressed until the fast selection
for the next or previous track starts.
Fast search
(repeat function ended)
T02-0248
-
1.
on the touch screen menu.
or
1.
or
times.
several times.
button.
The track is audibly scanned forward or back.
2.
Touch the button again or press the button again to
continue playback at regular speed.
48
RPT
several times.
button repeatedly
✔
8
Repeat display with closed monitor
To search for a specific section during the playback of a track,
you can use the fast scan function.
1.
DISC
03.02.2006, 8:34 Uhr
CD-changer mode
Random track play (MIX)
Scanning all tracks (Scan)
The Mix function plays the tracks of the current CD or all CDs in
the magazine in random order.
The Scan function plays all the tracks of the current CD or all
CDs in the magazine in sequential order for approx. 10 seconds
each.
The selected Mix function is displayed on the monitor.
The selected Scan function is displayed on the monitor.
MIX
(random playback of current CD)
MIX
(random playback of all CDs)
SCAN
(play track of current CD)
(random playback ended)
SCAN
(play track of all CDs)
NORMAL
(scan function ended)
NORMAL
8
MIX
T01-0002
-
-
T02-0248
DISC
Mix display with closed monitor
DISC
SCAN
8
Scan display with closed monitor
1.
Mix
button once or
several times.
+
On the device: Press the 5 / MIX button once or several
times.
On the remote control: Press the MIX button once or
several times.
1.
Scan button once or
several times.
On the device: Press the 6 / SCAN button once or several
times.
On the remote control: Press the SCAN button once or
several times.
49
49
03.02.2006, 8:34 Uhr
50
MP3 CD mode
MP3 CD menu
Touch screen menu in MP3 CD mode
A
MP3
CD–MP3
K
FILE
001
TImE
00:02’44
NORMAL
Kuschelrock
1 Abba - I have a
B
A
AUX
UX 2
NAVI
NA
NORMAL
B
13:05
I have a dream
C
3 Art Garfunkel
3 Art Garfunkel
5 B.O.N - Take my
F
G
4 Austria 3 - Weu
D
5 B.O.N - Take my
E
Sound
L
Setup
Rear
K
J
Disp
H
Func
G
F
A
Display: Currently playing file
B
A
C
B
D
C
Exit playback
D
File selection up/down
E
Button: Scroll up/down in file list
E
F
Display: Graphical equaliser (Chicago IVDM-7003 only)
F
G
Display: Time
G
H
Display: ID3 tag information (if available)
H
J
Display: File list of currently playing folder
Button: Call file
I
K
Display: Currently playing folder
Button: Select folder up/down
L
K
A
2 America _ The L
E
ID3
A
AUX
UX 1
1 Abba - I have a
4 Austria 3 - Weu
H
CD - C
Kuschelrock
C
D
2 America _ The L
J
RADIO
50
03.02.2006, 8:34 Uhr
MP3 CD mode
Activating the MP3 CD mode
1.
Exiting playback
button.
1.
MP3
button until the MP3 CD menu is displayed.
✔
button on the touch
button.
Selecting folders
The file played last is playing.
Note: When you insert an MP3 CD, the device automatically switches to MP3 CD mode.
Selecting the next or previous folder:
1.
Note: Umlauts and special characters should not be
used while burning a folder and files since they are
not correctly displayed.
T02-0248
-
MP3
screen menu.
times.
or
button once or several
On the device: Press the 1 / -DISC or 2 / DISC+ button
once or several times.
several times.
1
or
button once or
Display with closed monitor: File, playing time, folder
Selecting files
1.
button or touch the
/ PLAY/PAUSE
Selecting the next file:
1.
touch screen menu.
repeatedly.
button
Selecting the previous file:
1.
touch screen menu. If you touch the button once, the current file will be played again from the beginning.
button repeatedly. If you press the button once, the
current file will be played again from the beginning.
51
51
03.02.2006, 8:34 Uhr
52
MP3 CD mode
Scrolling up/down in file list:
Repeating files (Repeat)
1.
The Repeat function is used to repeatedly play the current file or
the current folder.
or
button repeatedly.
To confirm the selected file, press the ENTER button.
REPEAT
REPEAT
NORMAL
Fast search
To search for a specific section during the playback of a file, you
can use the fast search function.
MP3
T02-0248
or
button on the
search.
Display with closed monitor: Repeat file
Display with closed monitor: Repeat folder
or
changes the search speed (2x, 4x, 6x, 8x).
✔
The selected speed is displayed on the monitor.
screen menu.
button on the touch
button.
MP3
button for fast
2.
1.
(repeat a folder)
(repeat function ended)
1.
T02-0248
-
1.
(repeat a file)
-
or
button repeatedly. To
confirm the selected file, touch the button of the file in the
list.
52
DISC
1
RPT
RPT
several times.
times.
several times.
/ PLAY/PAUSE
Note: When the start/end of the file is reached, the fast
scan automatically ends.
1
03.02.2006, 8:34 Uhr
MP3 CD mode
Random play of files (MIX)
Scanning all files (Scan)
The Mix function plays the files of the current folder or all folders
on the CD in random order.
The Scan function plays all the files of the current folder or all
folders on the CD in sequential order for approx. 10 seconds each.
The selected Mix function is displayed on the monitor.
The selected Scan function is displayed on the monitor.
MIX
(random playback of current folder)
SCAN
(scanning files of current folder)
MIX
(random playback of all folders)
SCAN
(scanning files of all folders)
T02-0248
1
MIX
MP3
Display with closed monitor: Random playback of
current folder
T02-0248
-
MP3
DISC
1
T01-0002
SCAN
1
Display with closed monitor: scanning files of current
folder
MIX
MP3
Display with closed monitor: Random playback of all
folders
Mix
button once or
several times.
+
On the device: Press the 5 / MIX button once or several
times.
On the remote control: Press the MIX button once or
several times.
T01-0002
DISC
SCAN
1
Display with closed monitor: scanning files of all folders
1.
1.
(scan function ended)
-
MP3
NORMAL
-
(random playback ended)
-
NORMAL
Scan button once or
several times.
On the device: Press the 6 / SCAN button once or several
times.
On the remote control: Press the SCAN button once or
several times.
53
53
03.02.2006, 8:34 Uhr
54
External sources
Add-on equipment
Selecting a connected device as signal source.
Two external audio/video sources can be connected to the AUX
inputs of the Aspen/Chicago IVDM-7003. If the AUX inputs are
activated in the setup menu, they can be selected as signal source.
For further details, please read the section “Selecting the external signal source” in the chapter “Setup menu”.
1.
Alternatively, the signal converter IVSC-3302 or IVSC-5502
can also be connected to the Aspen/Chicago IVDM-7003. The
IVSC signal source can be used to display all the sources
connected to the signal converter on the monitor of the Aspen/
Chicago IVDM-7003.
✔
Note: If a signal converter is connected to the device,
the buttons of the signal sources AUX 1 and AUX 2
are no longer available on the touch screen menu. In
this case, it is meaningful to connect all external sources to the signal converter and selected them via the
signal converter. However, if a device should be connected to the AUX inputs, you ca select it with the SRC
button on the device or on the remote control.
54
On the monitor: Touch the button of the desired signal
source on the touch screen menu.
On the device and on the remote control: Press the SRC
button until the desired signal source appears on the
monitor.
The selected AUX source is briefly displayed at the top of
the monitor.
AUX1
Brief AUX display with closed monitor, then display of
the time.
03.02.2006, 8:34 Uhr
External sources
Navigation system
2.
If a navigation system (e.g. TravelPilot EX-V) is connected to the
Aspen/Chicago IVDM-7003, you can display the navigation screen
on the monitor.
Note: To allow for dynamic destination guidance
(automatic traffic jam detours), the navigation system
must be connected to a suitable TMC source.
1.
screen menu.
NAVI
button on the touch
On the device or on the remote control: Press the NAVI
button.
✔
The navigation screen is displayed on the monitor.
On the monitor: Touch the center of the monitor to return
to the previous operating mode.
On the device or on the remote control: Press the NAVI
button again to return to the previous operating mode.
Voice output during navigation mode
If the navigation system is connected to the Aspen/Chicago IVDM7003 as described in the installation instructions, its voice output
for the driving suggestions are played back over the car sound
system. For this purpose, the volume of the currently set signal
source is decreased. The percentage decrease of the volume
can be set in the setup menu. For further details, read the section
“Volume decrease for voice output” in the chapter “Setup menu”.
You can change the volume of the driving suggestions during a
voice output.
1.
/
buttons.
If the volume is changed during a voice output, this value remains
valid until the volume is changed again during a voice output.
Note: If the setting range is insufficient, you can also
increase the volume of the TravelPilot EX-V. For this
purpose, read the operating instructions of the
TravelPilot EX-V.
Note: Touch screen operation is not possible during
navigation mode.
55
55
03.02.2006, 8:34 Uhr
56
Setup menu
Setup menu
Selecting the setup menu
A
Language
E
The setup menu of the Aspen/Chicago IVDM-7003 offers a
variety of options to customise the device.
1.
AUDIO
ENG
FRE
SPA
OTHERS
SUB–TITLE
ENG
FRE
SPA
OTHERS
MENU
ENG
GER
FRE
ITA
OFF
✔
SPA
Setup
button on the touch
On the remote control: Press the SETUP button.
B
D
screen menu.
The DVD setup menu is displayed.
Note: When you call up the setup menu, the DVD
setup menu is always displayed first.
You can select the following setup menus:
DVD > AUDIO > SCREEN > USER.
EXIT
A
Display: Selected submenu
B
Display: Menu entries of selected submenu
Button: Select menu entries
C
Button: Exit setup menu
D
Display: Submenus of selected setup menu
Button: Select submenu
E
Display: Selected setup menu
Button: Select setup menu
C
2.
On the monitor: Touch the button of setup menu E
repeatedly.
On the remote control: Press the SRC button repeatedly.
Each setup menu is divided into several submenus.
3.
On the monitor: Touch the button of the desired submenu D.
On the remote control: Select the desired submenu using
or
button.
the
Exiting the setup menu
4.
EXIT
button.
On the remote control: Press the SETUP button.
More detailed information is available in the descriptions of the
individual menus.
56
03.02.2006, 8:34 Uhr
DVD setup menu
Performing settings in the setup menu
DVD setup
The settings in the setup menu can be performed using the buttons of the setup menu or the buttons of the remote control.
Selecting a language
The detailed information about the individual menus contain only
descriptions of the operation via buttons.
The following overview features a description of the principal
operation using the buttons of the remote control. It allows you to
perform all the settings in the setup menu.
●
To call up the setup menu,
press the SETUP button.
●
To select between the setup menus,
press the SRC button repeatedly.
●
To select between the submenus,
or
button repeatedly.
press the
●
To activate menu entries,
press the ENTER button.
●
To select menu entries,
or
button repeatedly.
press the
●
To perform settings,
press the or button repeatedly.
●
To confirm settings you made,
●
To cancel settings without saving them,
press the / RETURN button.
●
To exit the setup menu,
press the SETUP button.
You can preset your preferred playback language for the DVD
sound and whether and in which language subtitles are shown.
This requires that the selected language is stored on the DVD
and that the DVD supports this function. With some DVDs, the
standard language is preset.
In addition, you can select the language of the menu texts for the
setup menu.
Note: English is the selected language for the figures
used in these instructions.
1.
Touch the
✔
The DVD “Language” submenu is displayed.
Setup
Language
AUDIO
ENG
FRE
SPA
OTHERS
SUB–TITLE
ENG
FRE
SPA
OTHERS
MENU
ENG
GER
FRE
ITA
OFF
SPA
EXIT
57
57
03.02.2006, 8:34 Uhr
58
DVD setup menu
2.
3.
4.
Select by touching “AUDIO” (playback language),
“SUB-TITLE” (subtitle) or “MENU” (language of menu
texts).
Perform the setting by touching the desired menu entry.
Touch the
EXIT
Touch the
2.
Touch the
✔
The DVD “Display” submenu is displayed.
Repeat steps 2 - 4 to perform additional settings, or
5.
touch the
EXIT
Setup
button.
Display
Note: Use the “OTHERS” menu entry to select languages listed on the DVD language code table (see
page 83). Enter the four-digit code of the desired language using the buttons 0 to 9 and confirm the
entry with the OK button.
5.
1.
ASPECT
TYPE
WIDE 16:9
NARROW
PAN & SCAN
LETTER BOX
Selecting the screen display mode
You can select from the aspect ratios for wide-screen display
16:9 (WIDE) and normal screen display 4:3 (NARROW).
In the “PAN & SCAN” setting, the image fills the entire screen.
The left and right margin of wide images (16:9 aspect ratio) is cut
off. If you select the “LETTER BOX” setting, a black stripe
appears at the top and bottom edge of the screen during the playback of wide images.
58
EXIT
3.
Select by touching “ASPECT” (aspect ratio) or “TYPE”
(display format).
4.
Perform the setting by touching the desired menu entry.
5.
Touch the
6.
6.
touch the
EXIT
EXIT
03.02.2006, 8:34 Uhr
DVD setup menu
Setting the parental control level
1.
Touch the
You can set the parental control level so that children can view
only movies that are age appropriate. If a DVD features a higher
parental control level, it can be played only after entering the password.
2.
Touch the
✔
The DVD “Parental Control” submenu is displayed.
3.
Activate “LEVEL” by touching it.
Note: Not all DVDs support the parental control feature.
Setup
button.
Parental Control
The following options can be selected:
LEVEL
8.unrated
●
1. General (G) – Suitable for all ages
●
2. Most audiences – Suitable for most age levels
●
3. Mature young audience (PG) – With parental guidance
●
4. Teenage audience (PG-13) – For children under the
age of 13 with parental guidance
●
5. Mature teenage audience – For mature teenagers
●
6. Mature audience (R) – For children under the age of
17 with parental guidance
●
7. Adult audience (NC-17) – Not suitable for children
under the age of 17
4.
Select the desired parental control level using the
or
button and touch the selected parental control level.
8. Unrated – No defined guidance
✔
The password entry menu appears.
5.
Enter the four-digit password using the buttons 0 to 9
and confirm the entry with the OK button.
6.
Touch the
●
Note: A password is required to change the parental
control level. For instructions, please read the section “Changing the password” in this chapter.
EXIT
EXIT
59
59
03.02.2006, 8:34 Uhr
60
AUDIO setup menu
Audio setup
Setting Dolby ProLogic 2 (Chicago IVDM-7003 only)
Setting the input level for external audio sources
1.
Touch the Setup button on the touch screen menu and
button.
then touch the
button.
then touch the
2.
Touch the
The “Input Level” AUDIO submenu appears.
✔
The “Audio Effect Control” AUDIO submenu is displayed.
3.
Activate “ProLogic2” by touching it.
1.
✔
button.
Input Level
AUX1
2V
4V
AUX2
2V
4V
NEXT
EXIT
ProLogic2
OFF
SFC
OFF
DownMIX
OFF
ProLogic
Studio
Music
Hall
Stereo
Church
Lt/Rt
BALANCE
+0
FADER
+0
NEXT
EXIT
2.
Select “AUX1” or “AUX2” by touching it.
3.
Touch the desired input voltage.
4.
To confirm the setting, touch the
5.
5.
touch the
EXIT
The following settings are available:
EXIT
button.
OFF > ProLogic > Music > Movie > Matrix
4.
Touch the desired setting. Touching the
button displays additional setting options.
5.
Touch the
60
EXIT
or
button twice to exit the menu.
03.02.2006, 8:34 Uhr
AUDIO setup menu
Setting environment audio effects (Chicago IVDM-7003
only)
1.
button.
then touch the
2.
Touch the
✔
The „Audio Effect Control“ AUDIO submenu is displayed.
3.
Activate “SFC” (environment audio effects) by touching it.
button.
Setting bass and treble (Aspen IVDM-7003 only)
1.
button.
then touch the
2.
Touch the
✔
ProLogic2
OFF
SFC
OFF
DownMIX
OFF
ProLogic
Studio
button.
BASS
+0
TREBLE
+0
BALANCE
+0
FADER
+0
Music
Hall
Stereo
Church
Lt/Rt
DownMIX
BALANCE
+0
FADER
+0
OFF
Stereo
Lt/Rt
NEXT
EXIT
NEXT
EXIT
3.
Activate “BASS” or “TREBLE” by touching it.
4.
adjust bass or treble.
5.
6.
6.
touch the
The following settings are available:
OFF > Studio > Hall > Church > Stadium > Movie > Club
4.
button displays additional setting options.
5.
Touch the
EXIT
or
EXIT
EXIT
button.
61
61
03.02.2006, 8:34 Uhr
62
AUDIO setup menu
Setting the speaker balance
Downmix function (Aspen IVDM-7003)
1.
Touch the
then touch the
2.
Touch the
✔
The downmix function in the audio setup’s “Audio Effect Control”
submenu is used to control the downmix mode for the audio/video outputs (VIDEO 1 OUT, VIDEO 2 OUT) and loudspeaker/
preamp outputs.
Setup
button on the touch screen menu and
button.
button.
ProLogic2
OFF
SFC
OFF
DownMIX
OFF
ProLogic
Studio
Music
Hall
Stereo
Church
Lt/Rt
BALANCE
+0
FADER
+0
NEXT
EXIT
3.
Touch “BALANCE” (volume distribution left - right) or
“FADER” (volume distribution front - rear) to activate it.
4.
adjust the volume distribution.
5.
6.
6.
touch the
EXIT
EXIT
button.
The downmix function on the remote control is used to control
the downmix mode for the loudspeaker/preamp outputs. If the
downmix mode is activated using the DOWNMIX button on the
remote control, this will have the same effect as deactivating
(“OFF” setting) the centre loudspeaker and subwoofer in the audio setup’s “Speaker Setup” submenu.
Since the Aspen IVDM-7003 is equipped with only one digital
signal processor (DSP), the downmix function for the audio/video outputs and for the loudspeaker/preamp outputs cannot be
configured independently of one another.
Note: If the downmix function has been deactivated
(“OFF” setting) in the audio setup’s “Audio Effect
Control” submenu and a signal source is selected that
has been encoded using the Dolby Digital 5.1 or DTS
5.1 process, there will be no centre sound information present at the audio outputs of VIDEO 1 OUT and
VIDEO 2 OUT. In order to indicate that this configuration does not make sense, the system mutes the audio outputs of VIDEO 1 OUT and VIDEO 2 OUT. On the
Aspen IVDM-7003, it therefore only makes sense to
deactivate the downmix function if an external amplifier and a centre loudspeaker are being used with the
system.
Note: For the Aspen IVDM-7003, downmix can be set
only if you called the setup menu in DVD mode. The
setting affects only the DVD mode.
62
03.02.2006, 8:34 Uhr
AUDIO setup menu
1.
button.
then touch the
2.
Touch the
✔
3.
Activate “DownMIX” (tow-zone mode) by touching it.
button.
BASS
+0
TREBLE
+0
BALANCE
+0
FADER
+0
Downmix function (Chicago IVDM-7003)
The downmix function on the remote control is used to control
the downmix mode for the loudspeaker/preamp outputs. If the
downmix mode is activated using the DOWNMIX button on the
remote control, this will have the same effect as deactivating
(“NONE” or “NO” setting) the centre loudspeaker and subwoofer
in the audio setup’s “Speaker Setup” submenu.
Since the Chicago IVDM-7003 is equipped with a second digital
signal processor (DSP), the downmix function is always activated for the audio outputs of VIDEO 1 OUT and VIDEO 2 OUT.
Irrespective of this, the downmix function for the loudspeaker and
preamp outputs can be set by activating/deactivating the centre
loudspeaker and subwoofer. As a result, the “DownMIX” menu
item in the audio setup’s “Audio Effect Control” submenu is not
applicable and will not be displayed.
1.
button.
then touch the
2.
Touch the
The following settings are possible:
✔
OFF:
3.
Activate “DownMIX” (tow-zone mode) by touching it.
DownMIX
OFF
Stereo
Lt/Rt
NEXT
EXIT
Keep the surround signal, i.e. no downmix
button.
Stereo: Convert surround signal to stereo signal
Lt/Rt:
Mix surround signal for rear speakers into the signal for
the front speakers
4.
Touch the desired setting.
5.
Touch the
EXIT
63
63
03.02.2006, 8:34 Uhr
64
AUDIO setup menu
7-band equaliser (Chicago IVDM-7003 only)
ProLogic2
OFF
SFC
OFF
DownMIX
OFF
ProLogic
Studio
The Chicago IVDM-7003 model features a 7-band equaliser which
allows you to optimise the music sound to your vehicle or to optimise the music style. Six sound presettings and one customised
setting (USER) are available for this purpose. The linear setting
(FLAT), which cannot be changed, deactivates the equaliser.
Music
Hall
Stereo
Church
Sound presettings for the following music styles are available:
Lt/Rt
BALANCE
+0
FADER
+0
NEXT
EXIT
CLASSIC > JAZZ > ROCK > POPS > BALLAD > DANCE
The customised setting allows you to adjust the music playback
to your personal taste by decreasing or increasing the available
frequency bands.
Note: We recommend you use a familiar CD/DVD to
make changes to the settings.
OFF:
Keep the surround signal, i.e. no downmix
Stereo: Convert surround signal to stereo signal
Lt/Rt:
4.
5.
Mix surround signal for rear speakers into the signal for
the front speakers
Touch the
EXIT
64
1.
button.
then touch the
2.
Touch the
✔
The “7Band Equalizer” AUDIO submenu is displayed.
3.
Activate “7EQ ITEM” (music style) by touching it.
4.
Select the desired sound presetting with the
button.
5.
Select the frequency band to be changed by touching it.
button.
03.02.2006, 8:34 Uhr
or
AUDIO setup menu
1.
button.
then touch the
2.
Touch the
✔
The “Speaker Setup” AUDIO submenu is displayed.
7Band Equalizer
7EQ ITEM
BALLAD
button.
+6
Speaker Setup
0
–6
75
150
400
1K
2.4K 6K
15K
CENTER
ON
OFF
SUB WOOFER
ON
OFF
NEXT
EXIT
6.
Adjust the level of the frequency band to the desired value
/
buttons.
with the
7.
To change the level of additional frequency bands, move
/
buttons.
the selection mark with the
8.
To exit the setting, touch the
9.
You can now perform additional settings or exit the menu
EXIT button twice.
by touching the
EXIT
button.
Speaker setup (Aspen IVDM-7003)
If you connected a center speaker or subwoofer to the Aspen
IVDM-7003, you must activate the corresponding speaker output
(setting “ON”).
If the speakers are not connected, select the setting “OFF”.
NEXT
EXIT
3.
Select “CENTER” or “SUB WOOFER” by touching it.
4.
Perform the setting by touching the desired speaker
setting.
5.
6.
6.
Touch the
EXIT
EXIT
button.
Note: If the center speaker output is set to “OFF”, its
audio signal is evenly distributed to the left and right
front speaker.
The subwoofer signal is not distributed since the
other signals already contain bass.
65
65
03.02.2006, 8:34 Uhr
66
AUDIO setup menu
Speaker setup (Chicago IVDM-7003)
The Chicago IVDM-7003 can be set according to the playback
frequency ranges of the connected speakers. Before performing
the settings, check which speakers (except for the subwoofer)
can produce low frequencies.
3.
Select “FRONT” (front speaker), “REAR” (rear speaker),
“CENTER” (center speaker) or “SUB WOOFER” by
touching it.
4.
Perform the setting by touching the desired speaker
setting.
Select the setting “LARGE” if the connected speaker can
produce low frequencies.
Note: The settings for the front speaker do not feature
the entry “NONE” since all vehicles are equipped with
front speakers.
Select the setting “SMALL” if the connected speaker cannot
produce low frequencies.
5.
Select the setting “NONE” or “NO” if no speaker is connected.
6.
6.
touch the
1.
button.
then touch the
button.
2.
Touch the
✔
The “Speaker Setup” AUDIO submenu is displayed.
Note: The audio signals for non-connected speakers
(setting “NONE” or “NO”) are added to the audio
signals of the connected speakers.
The audio signals of the rear speakers are added to
the front speakers.
FRONT
LARGE
SMALL
REAR
LARGE
SMALL
NONE
CENTER
LARGE
SMALL
NONE
YES
NO
The subwoofer signal is not distributed since the other
signals already contain bass.
NEXT
EXIT
66
button.
In the process, the audio signal of the center speaker
is evenly distributed to the left and right front speaker.
Speaker Setup
SUB WOOFER
EXIT
EXIT
03.02.2006, 8:34 Uhr
AUDIO setup menu
Setting a delay time
4.
You can set a delay time in milliseconds for the center and rear
speakers. This simulates a greater distance to the respective
speakers.
5.
6.
6.
Touch the
Note: For the Aspen IVDM-7003, the delay time can be
set only if you called the setup menu in DVD mode.
The setting affects only the DVD mode.
1.
button.
then touch the
2.
button. With the Chicago IVDM-7003,
Touch the
button.
first touch the
✔
The “Speaker Delay” (delay time) AUDIO submenu is
displayed.
Speaker Delay
CENTER
+0ms
REAR
+0ms
Repeatedly touch to the left or right of the scale to adjust
the desired delay.
EXIT
EXIT
button.
Adjusting the speaker level
You can adjust the volume distribution of the individual speakers.
Note: For the Aspen IVDM-7003, the speaker levels can
be adjusted only if you called the setup menu in DVD
mode. The setting affects only the DVD mode.
1.
button.
then touch the
2.
First, touch the
✔
The “Speaker Gain” (speaker level) AUDIO submenu is
displayed.
button, followed by the
button.
PREV
Speaker Gain
FRONT L
+0
FRONT R
+0
REAR L
+0
REAR R
+0
PREV
NEXT
EXIT
3.
Select “CENTER” (center speaker) or “REAR” (rear speaker)
by touching it.
NEXT
NEXT
EXIT
67
67
03.02.2006, 8:34 Uhr
68
AUDIO setup menu
3.
Select “FRONT L/R” (left/right front speaker), “REAR L/R”
(left/right rear speaker), “CENTER” (center speaker) or
/
buttons
“SUB WOOFER” by touching it. The
can be used to scroll back and forth in the menu.
Note: Deactivated speakers cannot be selected. For
instructions, please read the section “Speaker setup”
in this chapter.
4.
1.
2.
First, touch the
✔
The “Dynamic Range” AUDIO submenu is displayed.
6.
6.
Touch the
D.RANGE
OFF
PREV
Setting the dynamic range
NEXT
You can adjust the dynamic range between loud and soft
passages. For this purpose, the volume of soft passages is
increased and that of loud passages is decreased.
Note: The dynamic range can be set in increments from
“OFF” to “FULL” (maximum). Select the “FULL” setting for full dynamic adjustment.
EXIT
3.
Activate “D RANGE” (dynamic range) by touching it.
4.
Repeatedly touch to the left or right of the scale to
increase or decrease the dynamic range.
5.
Touch the
EXIT
Note: For the Aspen IVDM-7003, the dynamic range
can be adjusted only if you called the setup menu in
DVD mode. The setting affects only the DVD mode.
button.
button.
5.
EXIT
Dynamic Range
Repeatedly touch to the left or right of the scale to
increase or decrease the speaker level for the selected
speaker.
EXIT
button.
then touch the
68
03.02.2006, 8:34 Uhr
AUDIO setup menu
Setting volume decrease for voice output
3.
Activate “RESIDUAL” (residual value) by touching it.
If a navigation system is connected, the voice output of the navigation system is mixed with the sound of the currently set signal
source. In the process, the volume of the signal source is
decreased. The percentage decrease of the volume can be adjusted.
4.
Repeatedly touch to the left or right of the scale to adjust
the desired volume difference.
5.
Touch the
The setting “+0” mutes the sound of the signal source for the
duration of a voice output.
With the setting “+100”, the volume of the signal source is not
decreased during a voice output.
EXIT
button twice to exit the setting.
Sending a test sound to the speakers
This option allows you to send a test sound to the connected
speakers to test its proper function.
1.
button.
then touch the
1.
button.
then touch the
2.
2.
First, touch the
button.
button twice.
With the Chicago IVDM-7003, touch the
button.
First, touch the
button twice.
With the Chicago IVDM-7003, touch the
✔
The “TEST TONE” AUDIO submenu is displayed.
✔
The “Navigation” AUDIO submenu is displayed.
Test Tone
Navigation
FRONT L
FRONT R
PREV
RESIDUAL
+50
CENTER
PREV
REAR R
REAR L
SUB WOOFER
EXIT
EXIT
69
69
03.02.2006, 8:34 Uhr
70
SCREEN setup menu
3.
Touch the desired speaker.
Note: Deactivated speakers cannot be selected. For
instructions, please read the section “Speaker setup”
in this chapter.
✔
A test sound is emitted from the selected speaker for
approx. 3 seconds.
4.
Repeat the check for the other speakers.
5.
Touch the
EXIT
button twice to exit the test.
Monitor setup
Setting the monitor position
Set the monitor tilt so that you have the best possible view of the
screen.
The monitor can be set to two positions. The “BACKWARD” setting moves the monitor back and “FORWARD” moves it to the
front.
Setting the monitor for automatic opening/closing The setting
“Automatic” automatically opens or closes the monitor when the
ignition is turned on or off.
1.
Touch the
2.
Touch the
✔
The “Tilt” (monitor tilt) SCREEN submenu is displayed.
Setup
button.
Tilt
TILT
POSITION
OPEN/CLOSE
–2
–1
0
+1
BACKWARD
FORWARD
Automatic
Manual
+2
+1
EXIT
70
03.02.2006, 8:34 Uhr
SCREEN setup menu
3.
Select “TILT” (monitor tilt), “POSITION” or “OPEN/CLOSE”
by touching it.
4.
Control
Note: The setting “+2” for the monitor tilt cannot be
selected if “BACKWARD” was set for the position and
vice versa.
button.
5.
6.
6.
Touch the
EXIT
EXIT
Brightness
+0
Color
+0
Contrast
+0
Tint
+0
Dimmer
AUTO
1
2
3
Image settings
4
EXIT
The image quality of the monitor can be customised.
Note: We recommend to perform the image settings
while a DVD is inserted.
1.
Touch the
Setup
2.
Touch the
3.
Touch the
✔
The “Control” (image setting) SCREEN submenu is
displayed.
button.
button.
4.
Select “Brightness”, “Colour”, “Contrast”, “Tint” or
“Dimmer” by touching it.
✔
The image of the inserted DVD and a scale for the setting
are displayed.
5.
perform the setting.
6.
Use the
settings.
7.
EXIT button to end the setting and call up the
Use the
“Control” SCREEN submenu again.
8.
Touch the
Brightness
button to perform additional image
EXIT
71
71
03.02.2006, 8:34 Uhr
72
SCREEN setup menu
Activating/deactivating the touch screen monitor
Deactivating the touch screen monitor:
Before the screen can respond to the touch of a finger, the function must be activated (ON). With deactivated function (OFF),
the device can be operated only with the buttons of the remote
control and the buttons on the front of the device.
1.
Touch the
2.
Touch the
3.
Touch the
✔
The “Touch Screen” SCREEN submenu is displayed.
Activating the touch screen monitor:
1.
Press the SETUP button on the remote control and select
the SCREEN setup menu by repeatedly pressing the SRC
button.
2.
or
button to select the “Touch Screen”
Use the
submenu and press the ENTER button.
✔
The “Touch” menu entry is selected.
Setup
button.
button.
Touch Screen
Touch
ON
Adjust
OFF
INITIALIZING
Touch Screen
Touch
ON
OFF
EXIT
Adjust
INITIALIZING
EXIT
3.
Use the or button to select the entry “ON” and press
the ENTER button to confirm the setting.
4.
Press the SETUP button to exit the menu.
72
4.
Activate “Touch” by touching it.
5.
Touch the entry “OFF”, followed by the
confirm the setting.
6.
Exit the menu by pressing the SETUP button on the
remote control.
03.02.2006, 8:34 Uhr
EXIT
button, to
SCREEN setup menu
Setting the touch position
8.
This setting is required if the display position on the monitor and
the touch position on the monitor do no longer match. This may
be required after operating the device for several years.
Sequentially touch the fields at the bottom left and right on
the monitor.
✔
This concludes the setting and the “Touch Screen”
submenu is displayed again.
1.
Touch the
2.
Touch the
3.
Touch the
✔
The „Touch Screen“ SCREEN submenu is displayed.
Setup
Note: If you touch the entry “RETURN”, no setting is
performed and the “Touch Screen” submenu is
displayed again.
button.
button.
9.
Touch the
EXIT
Touch Screen
Touch
ON
Adjust
OFF
INITIALIZING
EXIT
4.
Activate “Adjust” by touching it.
5.
Touch the “INITIALIZING” entry.
✔
The settings menu is displayed.
6.
Touch the top left field on the monitor.
7.
Now touch the top right field on the monitor.
73
73
03.02.2006, 8:34 Uhr
74
USER setup menu
User setup
3.
Activate “OLD CODE” (old password) by touching it.
Changing the password
4.
You must change the password (0000 in the delivery state) to
protect your device against theft. The password is queried if the
device is to be operated again after an interruption of the supply
voltage.
To change the password, first enter the current password
using the buttons 0 to 9 and confirm the entry with the
OK button.
5.
Next, enter the new password in the “NEW CODE” (new
password) field.
6.
After entering the new password, you are asked to confirm
it by re-entering it in the “RE-CODE” (repeat new password) field.
7.
Touch the
In addition, the password is queried for the playback of DVDs
that are protected by parental control.
1.
Touch the
2.
Sequentially touch the
✔
The “ID Code” (password) USER submenu is displayed.
Setup
,
and
button.
EXIT
Wallpapers
The Aspen/Chicago IVDM-7003 allows for displaying seven different wallpapers. You can load your own images into the device
from a CD-ROM which can then be selected as wallpaper. In
addition, you can specify that the selected image is always displayed or that an automatic change of the stored images is performed.
ID Code
OLD CODE
NEW CODE
RE–CODE
EXIT
74
03.02.2006, 8:34 Uhr
USER setup menu
5.
Selecting the wallpaper
You can select the wallpaper to be displayed in radio, MP3,
audio CD and CD changer mode.
Touch a memory location (IMG1 - IMG7) to activate the
preview mode.
Note: The automatic image change should be deactivated for this operation. For instructions, please read
the section “Automatic image change” in this chapter.
1.
Touch the
2.
3.
Touch the
✔
The “Image Manager” USER submenu is displayed.
Setup
,
and
button.
button.
IMAGE1
RETURN
WALLPAPER
CLEAR
Image Manager
PREVIEW
IMG SWING
IMG1
ON
IMG2
IMG3
IMG4
OFF
EXIT
4.
Activate “PREVIEW” by touching it.
6.
Select the desired wallpaper with the
7.
Touch the “WALLPAPER” entry.
✔
The “Image Manager” submenu is displayed.
8.
Touch the
✔
The selected image is displayed as wallpaper.
EXIT
IMAGE
button.
Note: The wallpaper for the active audio source can
also be selected directly. For this purpose, touch the
Disp
button once or several times in the touch
screen menu or press the DISP / WALLPAPER button
on the remote control until the desired image is displayed.
75
75
03.02.2006, 8:35 Uhr
76
USER setup menu
Automatic image change
Deleting wallpapers
If image change is activated, the wallpaper changes with every
track played by an audio or MP3 CD. In radio mode, the wallpaper changes approx. every five minutes.
Proceed as follows to delete stored images:
1.
Touch the
2.
3.
Touch the
✔
Setup
,
and
button.
button.
1.
Touch the
2.
3.
Touch the
✔
IMG SWING
IMG1
IMG2
ON
OFF
IMG3
,
and
button.
button.
Image Manager
PREVIEW
Image Manager
PREVIEW
Setup
IMG SWING
IMG4
IMG1
IMG2
ON
OFF
IMG3
IMG4
EXIT
EXIT
4.
Activate “IMG SWING” (image change) by touching it.
5.
Touch “ON” or “OFF” to activate or deactivate the
automatic image change.
6.
Touch the
EXIT
4.
Activate “PREVIEW” by touching it.
5.
Touch a memory location (IMG1 - IMG7) to activate the
preview mode.
76
03.02.2006, 8:35 Uhr
USER setup menu
Loading wallpapers
You can also load your own wallpaper into the device from a CDROM. The software required for this purpose is located on the
enclosed CD-ROM.
IMAGE1
RETURN
WALLPAPER
1.
Create a download CD according to the programme
instructions. Use a CD-R blank for this purpose.
2.
Insert the download CD into the CD tray.
✔
The download menu appears after a few seconds.
CLEAR
Image Download
6.
Select the wallpaper to be deleted with the
7.
Touch the “CLEAR” entry.
✔
A confirmation dialogue appears.
8.
If you want to delete the image, touch “YES” and “OK”.
✔
The image is deleted and the monitor displays a black
area.
9.
If you want to delete additional images, repeat steps 6 - 8.
IMAGE
button.
EXIT
IMAGE 2
IMAGE 3
IMAGE 4
IMAGE 5
IMAGE 6
IMAGE 7
From this menu you can delete
a currently stored image,
or download a new image from your CD-ROM.
After you select the image file you would like to
edit (1–7). Hightlight file and press ENTER.
Choose "Clear" to delete stored image.
Choose "Update" to download new image from CD-ROM.
Press "SETUP" to exit when complete.
EXIT
10. If you want to exit the preview mode, touch the “RETURN”
entry.
11. Touch the
IMAGE 1
Note: The operating steps for loading images is
performed using the buttons on the remote control.
or
3.
Select the desired memory location using the
button and press the ENTER button.
✔
The content of the selected memory location is displayed.
77
77
03.02.2006, 8:35 Uhr
78
USER setup menu
You have the following options:
1.
If you want to delete the displayed image, select the
“CLEAR” entry and press the ENTER button.
✔
2.
Confirm with “YES” and “OK” by pressing the ENTER
button.
Or
1.
If you want to replace the displayed image with a new
image, select the “UPDATE” entry and press the ENTER
button.
✔
A list with the images stored on the download CD is
displayed.
FILE–001
STORE
3.
If this is not the desired image, use the
or
button to
load additional images from the download CD.
4.
If you want to save the loaded image, select the “STORE”
entry and press the ENTER button.
IMAGE_1.jpg
✔
IMAGE_2.jpg
5.
Confirm with “YES” and “OK” by pressing the ENTER
button.
✔
The image is stored at the selected memory location.
6.
If you want to load additional images from the download
CD, select the “RETURN” entry and press the ENTER
button.
✔
The download menu is displayed again.
IMAGE LIST IN CD–ROM
ENTER
: Preview & Store
SETUP
: End
IMAGE_3.jpg
IMAGE_4.jpg
IMAGE_5.jpg
2.
Use the
or
button to select the desired image and
✔
The image is loaded and then displayed on the monitor.
RETURN
78
Or
6.
If you want to exit the download process, press the
SETUP button.
✔
The download CD is ejected.
03.02.2006, 8:35 Uhr
USER setup menu
Setting date and time
6.
Touch the
You can set the date, the time format (12/24 hours) and the time.
In audio sources, the time is displayed at the bottom right of the
monitor.
7.
7.
touch the
1.
Touch the
2.
3.
Touch the
✔
The “Adjust Date & Time” USER submenu is displayed.
Setup
,
and
button.
button.
2005
MONTH
4
DAY
14
FORMAT
24H Style
In the setup menu you can configure whether you want to display
the image of a connected back-up camera as horizontal mirror.
For this purpose, the back-up camera must be connected to the
device as described in the installation instructions.
Mirroring the camera image while backing up
REVERSE: ON > OFF
Select “YEAR”, “MONTH”, “DAY”, “FORMAT”, “HOUR” or
/
buttons can be used to
“MIN” by touching it. The
scroll back and forth in the menu.
Perform the setting by repeatedly touching the
button.
Selecting the external signal source
EXIT
5.
You have the option of selecting different signal source for the
front and the rear of the vehicle. This allows the driver to listen to
the radio or another audio source while the rear passengers can
view a DVD by means of additional connected monitors and headphones.
NEXT
4.
EXIT
Two external audio/video sources can be connected to the AUX
inputs of the Aspen/Chicago IVDM-7003. If the AUX inputs are
activated, they can be selected as signal source.
Adjust Date & Time
YEAR
EXIT
Switching AUX inputs on/off
AUX 1/2: ON > OFF
Selecting the signal source for additional monitors
MONITOR 1/2: AUTO > DISC > RADIO > CDC > AUX1 > AUX2
or
79
79
03.02.2006, 8:35 Uhr
80
USER setup menu
1.
Touch the
Setup
2.
3.
Touch the
✔
The “External Source Setup” USER submenu is displayed.
,
and
button.
button.
External Source Setup
REVERSE
ON
OFF
AUX1
ON
OFF
AUX2
ON
OFF
MONITOR1
AUTO
DISC
RADIO
CDC
MONITOR2
AUTO
DISC
RADIO
CDC
Factory settings
You can reset the Aspen/Chicago IVDM-7003 to the standard
values (factory setting).
Note: To return the settings to their original value, you
need a password. For instructions, please read the
section “Changing the password” in this chapter.
1.
Touch the
2.
Setup
,
and
button.
button.
3.
Touch the
✔
The “Protected Configuration” (factory settings) USER
submenu is displayed.
Protected Configuration
Reset
Load Default Config
EXIT
4.
Select “REVERSE” (mirroring the camera image), “AUX1”,
“AUX2”, “MONITOR1” or “MONITOR2” by touching it.
5.
or
button displays additional setting options for the monitors.
6.
touch the
7.
7.
touch the
EXIT
EXIT
EXIT
80
03.02.2006, 8:35 Uhr
USER setup menu
4.
Activate “RESET” by touching it.
5.
Touch the “Load Default Config” entry.
✔
The password entry menu appears.
6.
Enter the four-digit password using the buttons 0 to 9
and confirm the entry with the OK button.
7.
Switch the device off and on again.
✔
All settings performed by you (except for password, date
and time) are returned to the factory settings.
Restart of the device software
If the Aspen/Chicago IVDM-7003 should be blocked due to a malfunction or no longer be operable in all functions, you can press
the reset button, e.g. with the tip of a ball-point pen, to initiate a
restart of the device software. The reset button is located behind
the detachable control panel. If the problem should still exist, please
contact your authorised dealer.
81
81
03.02.2006, 8:35 Uhr
82
Glossary
CD text
ID3 tag
Information on an audio CD that may contain the following data:
Identification in an MP3 file that may contain the following data:
-
Name of track
-
Name of track
-
Name of artist
-
Name of artist
-
CD name
-
Name of volume on which the title was released
-
Year of release
Dolby Digital
-
Music type
The digital multi-channel technology Dolby Digital operates with
up to 6 channels, thereby offering a true impression of spatial
depth and close reality. This is ensured by separate channels for
the left, the right and the center speaker in the front of the vehicle
as well as two full-range surround speakers in the rear of the
vehicle and a subwoofer.
-
Comments
Downmix
The downmix function allows you to create a stereo signal from a
Dolby Prologic signal.
This information can be stored in the MP3 file via the PC.
MP3
MP3 is a process developed by the Fraunhofer Institute for compressing CD audio data. Compression allows data to be reduced
to around 10% of their original size without a noticeable loss in
quality (at a bit rate of 128 kbit/s). If a lower bit rate is used to
convert CD audio data to MP3, you will be able to create smaller
files but this will be accompanied by a loss in audio quality.
DVD video
DVD video is a software standard specifically defined for video
signals by the DVD forum. An application layer is required in
addition to the DVD which specifies standards such as playback
speed, forward/reverse, interactivity, up to 8 sound tracks with
up to 8 channels or change of camera perspective.
82
03.02.2006, 8:35 Uhr
Specifications
Control panel / Monitor
Output power:
System:
NTSC/PAL auto switch
Power supply:
10.8 - 16.0 volt
Current consumption max:
5A
Standby:
7.3 mA
Operating temperature:
-20 °C - +70 °C
4 x 16 watt sine according
to DIN 45 324 at 14.4 V
4 x 45 watt max. power
Center speaker (Chicago IVDM-7003 only):
1 x 12 watt sine according
to DIN 45 324 at 14.4 V
1 x 25 watt max. power
Storage temperature:
-30 °C - +80 °C
Screen size (diagonal):
7" (17.5 cm)
Resolution (pixel):
1440 (H) x 234 (W) =
336,960 Pixel
Signal-to-noise ratio:
Harmonic distortion:
< 0.01 %
Viewable screen size:
152 (W) x 86 (H) mm
Speaker bandwidth:
20 Hz - 20 kHz +/- 2 dB
Control panel dimensions (WxHxD): 180 x 50 x 26.7 mm
Bandwidth (subwoofer):
-3 dB at 100 Hz +/- 2 dB
Amplifier
DVD, CD, CDC
AUX 1, 2
> 85 dB
Dimensions (WxHxD):
175 x 50 x 235 mm
> 95 dB
Power supply:
10.8 - 16.0 volt
Harmonic distortion:
< 0.01 %
Max. current consumption:
10 A
Bandwidth:
20 Hz - 20 kHz +/- 2 dB
Standby:
< 1 mA
Video input level (typ.):
1 Vpp, 75 ohm
Tuner
Audio output level (typ.):
4 Vrms +/- 0.2 Vrms
Wavebands
Channel separation:
< 55 dB
FM :
87.5 - 108 MHz
< 75 dB
AM :
531 - 1,602 kHz
Bandwidth:
20 Hz - 20 kHz +/- 2 dB
Channel tracking:
> 0.5 dB
Harmonic distortion (RMS):
< 0.05 %
FM bandwidth:
20 - 16,000 Hz
Subject to change without notice!
83
83
03.02.2006, 8:35 Uhr
84
DVD language code table
6566 Abkhazian
7587 Cornish
7285 Hungarian
7684 Lithuanian
8073 Pali
8476 Tagalog
6565 Afar
6779 Corsican
7383 Icelandic
7775 Macedonian
8065 Panjabi
8489 Tahitian
6570 Afrikaans
7282 Croatian
7378 Indonesian
7771 Malagasy
7065 Persian
8471 Tajik
8381 Albanian
8372 Croatian
7365 Interlingua
7783 Malay
8076 Polish
8465 Tamil
6577 Amharic
6783 Czech
7369 Interlingue
7776 Malayalam
8084 Portuguese
8484 Tatar
6582 Arabic
6865 Danish
7385 Inuktitut
7784 Maltese
8083 Pushto
8469 Telugu
7289 Armenian
7876 Dutch
7375 Inupiaq
7186 Manx
8185 Quechua
8472 Thai
6583 Assamese
6890 Dzongkha
7165 Irish
7773 Maori
8277 Raeto-Romance
6679 Tibetan
6569 Avestan
6978 English
7384 Italian
7782 Marathi
8279 Romanian
8473 Tigrinya
6588 Aymara
6979 Esperanto
7465 Japanese
7772 Marshall
8278 Rundi
8479 Tonga
6590 Azerbaijani
6984 Estonian
7487 Javanese
7779 Moldavian
8285 Russian
8483 Tsonga
6665 Bashkir
7079 Faroese
7576 Kalaallisut
7778 Mongolian
8377 Samoan
8478 Tswana
6985 Basque
7074 Fijian
7578 Kannada
7865 Nauru
8371 Sango
8482 Turkish
6669 Belarussian
7073 Finnish
7583 Kashmiri
7886 Navajo
8365 Sanskrit
8475 Turkmen
6678 Bengali
7082 French
7575 Kazakh
7868 Ndebele, North
8367 Sardinian
8487 Twi
6672 Bihari
7089 Frisian
7577 Khmer
7882 Ndebele, South
8382 Serbian
8571 Uighur
6673 Bislama
7168 Gaelic
7573 Kikuyu
7871 Ndonga
8378 Shona
8575 Ukrainian
6683 Bosnian
7176 Gallegan
8287 Kinyarwanda
7869 Nepali
8368 Sindhi
8582 Urdu
6682 Breton
7565 Georgian
7589 Kirghiz
8369 Northern Sami
8373 Sinhalese
8590 Uzbek
6671 Bulgarian
6869 German
7586 Komi
7879 Norwegian
8375 Slovak
8673 Vietnamese
7789 Burmese
6976 Greek
7579 Korean
8376 Slovenian
8679 Volapumk
6765 Catalan
7178 Guarani
7574 Kuanyama
7866 Norwegian
Bokmål
8379 Somali
6789 Welsh
6772 Chamorro
7185 Gujarati
7585 Kurdish
8384 Sotho, Southern
8779 Wolof
6769 Chechen
7265 Hausa
7679 Lao
7878 Norwegian
Nynorsk
6983 Spanish
8872 Xhosa
7889 Chichewa
7387 Hebrew
7665 Latin
8385 Sundanese
7437 Yiddish
9072 Chinese
7290 Herero
7686 Latvian
8387 Swahili
8979 Yoruba
6785 Church Slavic
7273 Hindi
7666 Letzeburgesch
8383 Swati
9065 Zhuang
6786 Chuvash
7279 Hiri Motu
7678 Lingala
8386 Swedish
9085 Zulu
84
7967 Occitan
7982 Oriya
7977 Oromo
7983 Ossetian
03.02.2006, 8:35 Uhr
Country:
Germany
Austria
Belgium
Denmark
Finland
France
Great Britain
Greece
Ireland
Italy
Luxembourg
Netherlands
Norway
Portugal
Spain
Sweden
Switzerland
Czech. Rep.
Hungary
Poland
Turkey
(D)
(A)
(B)
(DK)
(FIN)
(F)
(GB)
(GR)
(IRL)
(I)
(L)
(NL)
(N)
(P)
(E)
(S)
(CH)
(CZ)
(H)
(PL)
(TR)
Phone:
Fax:
www:
0180-5000225
01-610 39 0
02-525 5444
44-898 360
09-435 991
01-4010 7007
01-89583 8880
210 94 27 337
01-46 66 700
02-369 62331
40 4078
0800 400 1010
66-817 000
2185 00144
902 52 77 70
08-7501850
01-8471644
02-6130 0446
76 511 803
0800-118922
0212-335 06 71
05121-49 4002
01-610 39 391
02-525 5263
44-898 644
09-435 99236
01-4010 7320
01-89583 8394
210 94 12 711
01-46 66 706
02-369 62464
40 2085
0800 400 1040
66-817 157
2185 00165
91 410 4078
08-7501810
01-8471650
02-6130 0514
76 511 809
022-8771260
0212-346 00 40
http://www.blaupunkt.com
Blaupunkt GmbH, Robert-Bosch-Straße 200, D-31139 Hildesheim
02/06 CM-AS/SCS1 (GB)
8 622 404 595 Index B
85
06.02.2006, 8:53 Uhr
/

BA IVDM-7003 Teil 1 GB

Transcription

Similar documents

Contents - Vu Televisions

Vu 102 cms (40”) LED TV Model: 40D6575

Contents - Vu Televisions

32” / 40” / 50” / 55”

GXT1000 Owner`s Manual.qxp

MX-450: Auxiliary Remote Macro Editing On Screen No PC Required

LMD-1420 Manual

NickToons Racer Video Game

IMxVCD Help