Test + Measurement Equipment

Transcription

Test + Measurement Equipment
Test + Measurement
Equipment
G
R
O
U
VEHICLES
P
In line with our stated purpose of becoming the ONE commissioning completions
group, Powertech has been transformed into a new differentiated entity known as
the Present Group. When we have a PASSION for what we do and TRUST in one
another, only then do we become both naturally ALIGNED and fully ENABLED.
Over the years we have aspired to become our
clients most trusted servants and many have
gone on to become our friends. These friendships
have grown out of mutual trust and collaborative
understanding. It is one of our greatest rewards and
we continue to promote this friendly cooperation
in all our relationships, within and throughout our
Group of Companies.
In some ways the Present Group has emerged
ready formed and each of the four new domains;
Consulting, Resourcing, Services & Facilities
thoroughly complement one another. This degree
of differentiation is an essential transformation if
we are to realise our overriding purpose to become
the ONE Commissioning Completions Group. Our
WHY drives an acute sense of purpose to remove
and reduce the chronic waste of our all too finite
natural resources. To this end we believe we can
make the most impact in the world’s largest industry
sectors which are currently engaged in major
energy, resource and infrastructure projects. This
is where the stakes are not only the highest from
an economic standpoint but more importantly an
environmental one.
Chronic waste abounds not only in the resource
sense but also as the waste of life purpose,
OCTAVE CONSULTING is focused on providing
complete solutions to the most complex and
costly asset problems using its tools and expertise
to ensure that projects deliver assets to ‘name
plate’ performance, on time and budget. Octave
also provides effective governance of projects,
eliminating costly tail end overruns and optimising
the performance of assets through life.
Powertech
R
V
I
C
E
S
POWERTECH SERVICES provides world class
technical specialists across all engineering
disciplines to ensure the customer gets the
desired result in commissioning, testing, startup, maintenance and operations. Its technical
specialists are highly trained, experienced,
autonomous, reliable and tenacious.
F A C I L I T I E S
Precise
Our Full Mine Spec 2012 Toyota Hilux SR Dual
Cab Diesel vehicles are fitted with a steel tray, ARB
Bullbar, internal and external roll over bars, 77ch
Uniden UHF fitted with Bluetooth, GPS tracking
device which provides accurate location and a
detailed status of your fleet 24hrs a day, high
mounted LED lights, LED amber beacons, reverse
buzzers, clutch depression interlock, headlights on
kit, handbrake alarms, battery isolators, all of the
required OH&S safety equipment plus many extras.
These vehicles meet the highest of standards and
will pass any ‘Mine Spec’ compliance test.
With an ever growing demand of precision test
equipment and a means to power it in remote
or un-powered locations, Precise Facilities have
approached many of the leading manufacturers
of high quality diesel generators with Inverter
Technology to power even the most demanding
pieces of equipment safely and efficiently.
The Present Group encompasses four
complementary areas of expertise – Consulting,
Resourcing, Services and Facilities.
SEAMLESS RESOURCING provides large or small
multi-disciplined teams tailored to client needs,
whether it be testing or commissioning, validation,
verification, audit or hazard assessment. With
world class employee retention, it is able to rapidly
mobilise highly motivated individuals to deliver the
required client outcomes.
Precise
F A C I L I T I E S
PRECISE FACILITIES provides unrivalled
experience in the rental, sale and management of
inspection test and measurement equipment and
now Fleet Services. With a network of branches
Precise can provide sales, service, calibration and
support to meet all client needs. Precise has built a
reputation for excellence and reliability to become a
trusted OEM agent and advocate.
At Precise Facilities we pride ourselves on not
only supplying the highest standard of equipment
but also quality customer support that is second
to none.
GENERATORS
Headquartered in Perth Western Australia, the
Present Group comprises a national network with
offices and branches stemming into QLD, VIC
and NSW. With a client base comprising BHP
Billiton, Rio Tinto, Xstrata, Woodside, Chevron,
Santos, Origin and a project portfolio that includes
renewables, power stations, desalination, platforms,
refineries, mines, ports and rail, the Present Group’s
collective experience is without parallel.
R E S O U R C I N G
C O N S U LT I N G
E
Again and again on projects we have witnessed
both people and project serving the system, rather
than the system serving the greater good. This
results in massive waste, low morale and cost and
time overruns. At the Present Group we truly believe
that we can remedy this to the benefit of our clients
and our society.
Seamless
Octave
S
especially when we find it so very hard to find
personal meaning in a material world seemingly
headed for oblivion. And so instead our passion
remains dormant and we seldom experience the
sheer exhilaration of discovering our maximum
potential and releasing our full discretionary effort.
FLEET
PRESENT GROUP
Present
Precise Facilities now offers a full range of
Inverter Technology Generator Sets to complement
our already exemplary range of high quality Test
and Measurement Equipment and Fleet range
of services.
We stock generators ranging from 2KVA up to
100KVA and optional extras such as earth stakes
and multi combination power outlets. The larger
units are supplied with lockable, sound attenuated,
weatherproofed enclosures and will be servicing
all major mine sites around Australia. The smaller
units will be coupled with our mobile stores and
calibration labs and are more customised to suit
smaller technician teams needing an off grid
power supply.
CONTAINERS
Precise Facilities can provide tailored site
construction and commissioning facilities to meet
your requirements with containerised solutions for
permit offices, workshops, instrument calibration,
stores and security check points and offices.
All of our containerised options are built to the
highest standards and meet the most stringent
site requirements. In addition to the list above
we can custom build any container to suit your
business needs.
Pr
F A
Seaward Primetest 300 PAT Tester
APPLIANCE TESTERS
Seaward Primetest 300 PAT Tester
05
05
OIL TESTERS
Megger OTS80PB 80KV Oil Test Set with Roadcase
08
08
CT TEST EQUIPMENT
Omicron CT Analyser
05
05
CURRENT CLAMPS
Fluke 1010 600A AC/1000A DC Current Probe
05
05
POWER ANALYSER
Fluke 1735 Power Quality Analyser
Fluke 435 Power Quality Analyser
Yokogawa CW240 Power Quality Analyser
08
08
08
09
CURRENT CLAMP METERS
Hioki 3283 200A AC Leakage Clamp Meter
05
05
CURRENT INJECTION SETS
T&R 750ADM Current Injection Set
05
05
PROTECTION RELAY TEST SETS
Omicron CMC256-6 Plus
Omicron CMC356
09
09
09
05
05
09
09
CT TEST EQUIPMENT
DC POWER SUPPLIES
Chroma 62024P 100V 50A DC Power Supply
CIRCUIT BREAKER TEST SETS
Programma EGIL Circuit Breaker Analyser
06
06
09
09
Omicron CT Analyser
EARTH TESTERS
Fluke 1625 Earth Tester
SUBSTATION/PRIMARY INJECTION TEST SETS
Omicron CPC100 Substation Test Set
10
HI POTENTIAL TESTERS
HV Inc ALT-120/60 Hipot Tester 120KVAC/60KVAC
06
06
TAN DELTA TEST SETS
HV Diagnostics TD60 Portable 60KV
Tan Delta Measurement
INSULATION RESISTANCE TESTERS
Megger MIT1020 10KV Insulation Tester
06
06
10
LOAD BANKS
Programma Torkel 860 Battery Load Unit
06
06
TRANSFORMER TESTERS
DV Power RMO60TD Winding Ohmmeter
and Tap Changer
Megger TTR100 Turns Ratio Tester
Omicron Dirana DRA2 Standard Package
MICRO OHMMETERS
Megger DLRO10HD 10A Micro Ohmmeter
Megger DLRO200 200A Micro Ohmmeter
DV Power RMO600 600A Micro Ohmmeter
07
07
07
07
VLF TEST SETS
Baur Frida VLF Test Set 23KVAC
HV Diagnostics HVA60 VLF Test Set
44KVAC RMS/60KVDC
HV Diagnostics HVA90 VLF Test Set
64KVAC RMS/90KVDC
11
11
CURRENT CLAMPS
CURRENT CLAMP METERS
11
Fluke 1010 600A AC/1000A
DC Current Probe
Hioki 3283 200A AC Leakage
Clamp Meter
EARTH INJECTOR TEST SET
Mitton LCI 2058 Earth Injection Test Set
11
11
LINE IMPEDANCE
Omicron CU1
11
11
Battery Powered
1-1000A Hall Effect
Clamp. Output is 1mv
per Amp. Measure up
to 600A AC & 1000A
DC current. Minimum
current measurement
is 500ma.
Easily monitor leak current
fluctuations. Wide bandwidth,
5Hz to 15KHz (Waveform
output). High-sensitivity with a
full scale of 10mA (resolution:
10µA). High-accuracy at ±1%.
True RMS measurement. Analyser
functions for filtering and output
signals.
MULTIMETERS07
Fluke 289 True-RMS Industrial Logging Multimeter
with TrendCapture
07
PROCESS METER
Fluke 789 Process Meter
08
08
10
11
LIGHT METERS
ISO-TECH 1335 Digital Light Meter
12
12
VIBRATION CALIBRATOR
Modal Shop 9100D Portable Vibration Calibrator
12
12
SOUND METERS
TES 1350A Sound Meter (Digital)
12
12
PROXIMITY SENSOR CALIBRATOR
Bentley Navada TK-3e Proximity Sensor Calibrator
12
12
GAS DETECTOR
Dräger X-AM 2000 with External Pump
12
12
Primary current injection up to 750A. 2.8V output (750ADM)
4V output (750ADM-H). 16V 40A output for secondary injection. True RMS
digital metering. Memory ammeter. Multi-function timing system. Large back-lit
liquid crystal display. Thermal and over-current Protection. Automatic switch-off
at end of test. Compact and portable. Automatic mains voltage selection.
CABLE LOCATORS
Cscope SG-V Cable Locator
Cscope MXL/MXT Cable Locator
Fluke 2042 Cable Locator/Tracer
13
13
13
13
VIBRATION ANALYSERS
Commtest VB7 Vibration Analyser
CABLE FAULT LOCATION
Megger TDR2000/2R Time Domain Reflectometer
13
13
MANOMETERS16
Digitron 2021P Digital Manometer 130mbar
16
COMMUNICATORS14
Emerson Rosemount 375 Field Communicator
HART & Fieldbus
14
Emerson 475 Field Communicator HART & Fieldbus
14
OSCILLOSCOPES14
Fluke 123 Digital 20Mhz 600V Scopemeter
14
Fluke 199C Digital Colour 200Mhz 1000V Scopemeter 14
Tektronix TPS2014 Digital Colour 100Mhz Scopemeter 15
F A C LASER
I L I TALIGNMENT
I E S
Pruftechnik AG ALI5.200 Optalign Plus
CURRENT INJECTION SETS
T&R 750ADM Current Injection Set
GENERAL INDUSTRIAL
Precise
The CT Analyser automatically determines all relevant current transformer
values and compares the results with the selected standard. The device
evaluates the current transformer as per the IEC or IEEE standard within
seconds with the push of a button. It facilitates fast and economical on-site
testing and calibration of metering and protection current transformers.
10
10
10
ENVIRONMENTAL
PROCESS CALIBRATORS
Beamex MC5-E-ET-RJ Multifunction Calibrator
with Fieldbus
Fluke 726 Process Calibrator
Fluke 744 Logging Process Calibrator
Lightweight PT300 weighs less than 1kg. Battery powered portable appliance tester.
Test to AS3760 with ease. Includes built in Bluetooth. This unit fully supports the
Patguard Elite software.
ELECTRICAL
APPLIANCE TESTERS
15
15
15
15
16
16
16
16
VIDEOSCOPE16
Olympus IV7630X2 Videoscope
16
PRESSURE CALIBRATORS
Crystal XP2i Pressure Calibrator
Druck DPI620 Advanced Pressure Calibrator 1000bar
17
17
17
TEMPERATURE CALIBRATORS
17
Fluke 9009 Dry Well Calibrator -15 Deg C to 350 Deg C 17
Fluke 9173 Dry Well Calibrator 50 Deg C to 700 Deg C 17
THERMOGRAPHIC CAMERAS
Flir Thermacam T360 Thermographic Camera
Fluke Ti32 Thermo Camera with 2x Lenses
Flir E45 Thermographic Camera
18
18
18
18
WAVEFORM RECORDERS
Hioki 8847 Waveform Recorder
18
18
DC POWER SUPPLIES
Chroma 62024P 100V 50A DC Power Supply
2400W, 0 to 80V, 0 to 60A. Digital encoder knobs, keypad and function
keys. Power Factor Correction (0.95) High-speed Programming
Precision Voltage and Current Measurements. Current sharing for
parallel operation with Master/Slave Control. Voltage ramp function:
Time Range (10ms to 99 hours). Auto Sequencing Programming: 10
Programs/100 Sequences/8-bit TTL. Voltage & Current Slew Rate
Control OVP, Current Limit, Thermal protection. Remote sense, 5V line
loss compensation. APG (Analog Programmable Interface) with Isolated
Analog Interface Card. Standard RS-232 and USB interface.
05.
CONTENTS
ELECTRICAL
Pr
F A
Email [email protected] for additional information
MICRO OHMMETERS
Fluke 1625 Earth Tester
Megger DLRO10HD 10A Micro Ohmmeter
3- and 4-pole earth ground measurement. 4-pole soil resistivity
testing. 2-pole resistance measurement AC. Selective testing, no
disconnection of ground conductor (1 clamp). Stakeless testing, quick
ground loop testing (2 clamps). Earth impedance measurement at
55Hz. Automatic frequency control (AFC) (94, 105, 111 and 128Hz).
‘R’ measurement, calculates earth ground impedance at 55Hz to more
accurately reflect the earth ground resistance that a fault-to-earth
ground would see. Adjustable limits, for quick test result verification.
Measuring voltage switchable 20/48V. Programmable limits and
settings. Continuity with buzzer.
ƒƒ High or low output power selection for condition diagnosis.
Rechargeable battery or line power supply, continuous operation,
even with dead battery.
ƒƒ 10A for 60 seconds, less time waiting to cool, great for charging
inductance.
ƒƒ High input protection to 600V, inadvertent connection to line or UPS
voltage will not blow a fuse. Heavy duty case: IP 65 lid closed, IP54
operational (battery operation only). Rotary switch selects one of five test
modes, including auto start on connection, giving ease of use.
ELECTRICAL
ELECTRICAL
EARTH TESTERS
MICRO OHMMETERS
HI POTENTIAL TESTERS
HV Inc ALT-120/60 Hipot Tester 120KVAC/60KVAC
7KVA of output power. 120/230 volt, 25/15 amp input power requirements. 1hr @
7KVA and continuous duty @ 4KVA. 250µA current meter range. Transit protection
meter circuits. Optional Capacitive load current cancellation circuit which allows
the user to read resistive currents. Guard/Ground Return for isolating ground
currents to measure leakage current or total current. Zero start high voltage and
external safety interlock provision. Cable storage area. Internal kilovolt meter
divider resistors (no external voltmeter divider). Test timer circuit. Ruggedized
meters with glass windows that eliminate static build-up.
Megger DLRO200 200A Micro Ohmmeter
ƒƒ Small and weighs less than 15kg. Test currents from 10A to 200A DC.
ƒƒ 0.1µΩ best resolution. On board memory for up to 300 test results
and notes.
ƒƒ RS232 port to download stored results or for real time output to a printer.
ƒƒ Supplied complete with 5m test leads and download software.
MICRO OHMMETERS
DV Power RMO600 600A Micro Ohmmeter
INSULATION RESISTANCE TESTERS
Megger MIT1020 10KV Insulation Tester
ƒƒ
ƒƒ
ƒƒ
ƒƒ
10KV Insulation Resistance Tester. Rated CAT IV 600V.
Mains or battery powered.
Digital/analogue backlit display.
Variable test voltage from 50 to 5000V, automatic IR, PI, DAR, SV and
DD tests Measures to 35TΩ. RS232 and USB download of results.
RMO600G is a Micro Ohmmeter based on state of the art technology,
using the most advanced switch mode technique available today.
RMO600G generates true DC ripple free current with automatically
regulated test ramps. During the test RMO600G ramps with increasing
current before measuring and decreasing current after the measurement.
This eliminates magnetic transients. After the test current has been set,
the automatic test procedure is started by pressing the Ω-button.
The RMO600G instrument can store up to 500 measurements.
All measurements are time and date stamped.
MULTIMETERS
Fluke 289 True-RMS Industrial Logging Multimeter with TrendCapture
LOAD BANKS
Programma Torkel 860 Battery Load Unit
07.
Large 50,000 count 320x240 (1/4 VGA) dot matrix display. 0.025% Basic DC accuracy
Multiple readings per display provide more information at a glance. “i” – info button for
convenient on-board help. PC interface for easy data transfer. Log multiple sessions or
log data continuously for over 200 hours. 100KHz AC bandwidth. Low input impedance
function (LoZ). Motor winding & low ohm measurement range. Low pass filter. CAT III
1000 V/CAT IV 600V safety rated.
06.
Batteries can be tested “in service”. Unit adjusts to include load currents in the
test parameters. User adjustable alarm and shutdown points to avoid excessive
discharge. Easily expandable for larger battery banks using TXL extra load units
(option). Computerized test operation using TorkelWin software (option).
The new Fluke 289 True-RMS Industrial Logging Multimeter with TrendCapture is the
next generation high performance industrial logging multimeter designed to solve
complex problems in electronics, plant automation, power distribution, and electromechanical equipment. With the ability to log data and review it graphically on-screen,
you can solve problems faster and help minimize downtime.
Precise
Pr
F A C I L I T I E S
F A
Call 1300 736 292 for assistance and advice
Email [email protected] for additional information
POWER ANALYSER
Fluke 789 Process Meter
Yokogawa CW240 Power Quality Analyser
24V Loop power supply. Very large dual display with enhanced backlight with 2 brightness
settings. 1200ohm drive capability on mA source. HART mode setting with loop power and
a built-in 250ohm resistor. 0% and 100% buttons to toggle between 4 and 20mA sourcing
for a quick span check. Externally accessible fuses for easy replacement. Infrared-port to
process data in FlukeView Forms (V2.1) software.
Electric power analysis and power supply quality control in a single unit.
Simultaneous measurement of loads in four systems (common to voltage). Wide
measurement range. Leakage current measurement in four channels. Wiring and
Settings check function. Supplied with 700A clamp, others also available.
0.1% DC voltage accuracy 0.05% DC current accuracy. Frequency measurement to
20KHz, Min/Max/Average/Hold/Relative modes, Diode Test and Continuity Beeper,
Simultaneous mA and % of scale readout. 20mA DC current source/loop calibrator/
simulator. Manual Step (100%, 25%, Coarse, Fine) plus Auto Step and Auto Ramp.
OIL TESTERS
Megger OTS80PB 80KV Oil Test Set with Roadcase
Megger’s automatic portable oil test sets perform accurate breakdown
voltage tests on mineral, ester and silicon insulating liquids. Moulded
test vessels give repeatable results in the field and laboratory with lock
in precision electrode gap setting adjustment wheels. The transparent,
shielded lid is a key feature enabling users to see what is happening within
the test chamber. Lock in precision – oil vessel with lockable adjustment.
Bright 3.5 inch colour display visible outdoors. Trip detection circuit with
direct measurement of voltage and current. Ultra-fast (<10μs) HV switch
off time.
PROTECTION RELAY TEST SETS
PROTECTION RELAY TEST SETS
Omicron CMC256-6 Plus
Omicron CMC356
The CMC 256plus is the first choice for
applications requiring very high accuracy. This
unit is not only an excellent test set for protection
devices of all kinds but also a universal calibrator.
Its high precision allows the calibration of a wide
range of measuring devices, including: energy
meters of class 0.2, measuring transducers,
power quality measurement devices and phasor
measurement units (PMU). Its unique accuracy
and flexibility makes the CMC 256plus ideal
for protection and measurement equipment
manufacturers, for research and development,
production and type testing.
The CMC356 is the universal solution for testing
all generations and types of protection relays.
Its powerful six current sources (three-phase
mode: up to 64A/860VA per channel) with a great
dynamic range, make the unit capable of testing
even high-burden electromechanical relays with
very high power demands.
ELECTRICAL
ELECTRICAL
PROCESS METER
The CMC356 is the first choice for applications
requiring the highest versatility, amplitude and
power. Commissioning engineers will particularly
appreciate its ability to perform wiring and
plausibility checks of current transformers by
using primary injection of high currents from the
test set.
POWER ANALYSER
Fluke 1735 Power Quality Analyser
POWER ANALYSER
Fluke 435 Power Quality Analyser
Capture fast RMS data, show half-cycle and waveforms to
characterize electrical system dynamics (generator startups, UPS switching etc.). Classic active and reactive power
measurements, unbalance and harmonic power, are quantified
to pinpoint the fiscal costs of energy losses.
08.
Troubleshoot real-time & analyse the trends using the cursors and
zoom tools.
600V CAT IV/1000 V CAT III rated for use at the service entrance. The Fluke
435 can measure all three phases and neutral with included four flexible
current probes with enhanced thin flex design to fit into the tightest places.
Automatic Trending means every measurement is always automatically recorded, without any set-up.
Ten power quality parameters on one screen according to EN50160 power quality standard.
Using the logger function you can configure for any test condition with memory for up to 600 parameters
at user defined intervals. View graphs and generate reports, with included analysis software. Battery life is
seven hours operating time per charge.
CIRCUIT BREAKER TEST SETS
Programma EGIL Circuit Breaker Analyser
The Programma EGIL is an automatic timer and motion analyser for mediumand high-voltage substation circuit breakers. It is intended for use on circuit
breakers with one contact per phase. EGIL incorporates features commonly
found on more complex test systems, but is designed to be smaller, simpler to
use and less expensive than other similar test sets. Its price makes it attractive
to smaller utilities and it is an ideal supplementary product for maintenance
departments at larger power companies and for testing contractors.
SUBSTATION/PRIMARY INJECTION TEST SETS
Omicron CPC100 Substation Test Set
Electrical tests on transformers, current transformers, voltage
transformers, grounding systems, lines and cables, and circuit
breakers can be performed with the CPC100. The CPC100 is the
base for multiple accessories. These facilitate further applications,
such as tan delta measurements, as well as line and ground
impedance measurements. Up to 800A or 2000V with up to
5KVA over a frequency range of 15-400Hz or 400A DC. Excellent
interference suppression facilitates measurement of small signals. Easy to transport – Ideal for on-site
testing. Testing templates automatically generated testing procedures and test reports. Up to 2000A or
12KV through use of current or voltage amplifiers.
09.
Record power and associated parameters for up to 45 days. Monitor maximum
power demand over user-defined averaging periods. Prove the benefit of efficiency
improvements with energy consumption tests. Measure harmonic distortion
caused by electronic loads. Improve reliability by capturing voltage dips and
swells from load switching. Easily confirm instrument setup with colour display of
waveforms and trends. Measure all three phases and neutral with included current
rating on flexible current probes. View graphs and generate reports with included
Power Log software. Compact, rugged design with IP65 case, 600V CAT III.
Precise
Pr
F A C I L I T I E S
F A
Call 1300 736 292 for assistance and advice
Email [email protected] for additional information
VLF TEST SETS
HV Diagnostics TD60 Portable 60KV Tan Delta Measurement
Baur Frida VLF Test Set 23KVAC
Tan Delta (also referred to as “Power Factor”) is the ratio of the
Resistive Power versus the Capacitor Power of the dielectric
material. It is the measure of the quality of the insulation medium.
The TD60 provides the testing and commissioning engineer with a
high voltage tan delta measuring system suitable for testing cables:
XLPE, PE, EPR, PILC and other electrical equipment: capacitors,
switchgear, transformers and rotating machines.
On-site testing of medium voltage cables according to VDE DIN 0276-620/621
(CENELEC HD 620/621), IEEE P 400-2-2004, IEEE 400-2001. Cable Sheath
testing/Sheath fault location. Insulation tests on electrical equipment, such as
rotating machines (motors and generators) according to IEEE 433. Compact,
easy portable testing equipment. VLF truesinus® high voltage source.
Tan Delta testing enables the cable test engineer to detect insulation defects before the cable fails in service.
The TD60 is a versatile tan delta measuring system that is directly connected to the HV Diagnostics and HVA
Series of VLF Test Systems. The tan delta of the test object can be measured quickly and the results stored,
thus providing a “signature” of the cable being tested. This enables the cable engineer to make tan delta a
routine test and combine this diagnostic test with the normal over voltage pressure “testing” to provide a
smart VLF test.
Fully automatic programmable test sequences. Data communication and saving
via USB-interface. Integrated cable case with connection cable. Automatic,
integrated discharging device. Extendable to diagnosis system for tan delta and
partial discharge measurement.
ELECTRICAL
ELECTRICAL
TAN DELTA TEST SETS
VLF TEST SETS
HV Diagnostics HVA60 VLF Test Set 44KVAC RMS/60KVDC
TRANSFORMER TESTERS
DV Power RMO60TD Winding Ohmmeter and Tap Changer
The Tap Changer Analyser & Winding Ohmmeter RMO60TD is designed
for tap changer analysis and for resistance measurement of inductive test
objects. RMO60TD generates true DC ripple free current. Both injection
of current and discharge of energy from the inductance are automatically
regulated.
RMO60TD injects current with a voltage as high as 60V. This ensures that
the duration of test is as short as possible, and that the desired test current
is reached faster. Two independent channels enable testing of two series
windings, or primary and secondary windings. There is enough memory within
RMO60TD instrument to store 500 measurements (EEPROM memory).
The HVA60 model is capable of testing 1µF (Approx. 10,000ft/3,000m of cable)
at 0.1Hz and 62KV peak. The frequency or voltage of the output can also
be reduced allowing even larger capacitance loads to be tested – at 0.02Hz,
approx 50,000ft/15,000m of cable can be tested. Test results are stored in the
instrument’s onboard memory allowing easy retrieval and download to a PC/
Laptop for review and analysis.
VLF TEST SETS
HV Diagnostics HVA90 VLF Test Set 64KVAC RMS/90KVDC
Apart from the variable frequency VLF output, the operator can also select dual
polarity DC and cable jacket or sheath testing output modes.
The applied test voltage, current, capacitance, resistance and time are displayed
and recorded. The instrument is easily programmable allowing the operator to
setup or select test sequences in either automatic or manual mode.
TRANSFORMER TESTERS
Megger TTR100 Turns Ratio Tester
Omicron Dirana DRA2 Standard Package
Tests turns ratio, phase
displacement, excitation
current, vector group, winding
resistance and polarity. Fully
automatic; fast; easy-to-use;
handheld; robust; lightweight
Battery powered with powersaving and shutdown function.
The DIRANA can determine the condition
of high-voltage insulation systems in power
transformers, bushings, cables and generators
with dielectric response analysis. On the basis
of the dielectric frequency response (DFR) the
DIRANA can determine the moisture content in
oil-paper insulations. The measurement results
are compared against values from an integrated
database and the moisture content is graded
between “dry” and “very wet” as per IEC 60422.
The DIRANA reduces the required measurement
time to 50%, as the device uses a combination
of the time and frequency range method
(Polarization Depolarization Current [PDC] and
Frequency Domain Spectroscopy [FDS]).
10.
Alphanumeric keyboard,
RS232 for data transfer and
printing. Stores 200 test
results and 100 user-defined
transformer test settings.
Precise
The HVA90 is capable of testing 1μF (Approx. 3,300m/11,000ft of cable) at 0.1Hz
and 64KV rms. The frequency of the output can also be reduced allowing even
larger capacitance loads to be tested. At 0.01Hz, approx. 33,000m/100,000ft of
cable can be tested.
EARTH INJECTOR TEST SET
LINE IMPEDANCE
Mitton LCI 2058 Earth Injection Test Set
Omicron CU1
The Low Current Injector (LCI) provides a reliable
method for testing earth/grounding systems,
particularly those with low impedance (<2ohms)
or which are extensive and where noise is
present on the earthing system. Portable earth
testers are often unsuited to testing such earth/
grounding systems due to limited test current and
inadequate noise rejection.
The CPC 100 + CP CU1
measure line impedances
and k-factors on
overhead lines
and power
cables. Ground
impedances
can also be
determined on large systems with the CP CU1,
as well as touch and step voltages.
The LCI 2058 provides a reliable and simple
means to test power system earthing/grounding
systems. The
LCI 2052 is an
off-frequency
constant current
source used to
inject current
into the earthing/
grounding system
under test.
Mains frequency malfunctions do not influence
the measurements, as the CPC 100 + CP CU1
use variable output frequencies. This enables
extremely precise and reproducible results.
To increase safety for the test engineer, the CP
CU1 is supplied with the CP GB1 grounding
unit. This can divert currents of up to 30KA if its
voltage limit value is exceeded.
F A C I L I T I E S
Call 1300 736 292 for assistance and advice
11.
TRANSFORMER TESTERS
Pr
F A
Email [email protected] for additional information
CABLE LOCATORS
ISO-TECH 1335 Digital Light Meter
TES 1350A Sound Meter (Digital)
Cscope SG-V Cable Locator
ƒƒ Measurement range:
0 to 400,000 lux.
ƒƒ 4 ranges/times covered.
ƒƒ Data hold max/min
function.
ƒƒ Relative readings.
ƒƒ Auto power off.
ƒƒ 4000 count reading
with instant bar
graph indication.
ƒƒ Large, easy to read LCD display.
ƒƒ 0.1dB Resolution, Maximum
hold function, AUX OUTPUT
JACKS.
ƒƒ Specification: Standard applied
IEC 651 Type2.
ƒƒ Range A LO (Low) – Weighting:
35-100dB, A HI (High) –
Weighting: 65-130dB, C LO
(Low) – Weighting: 35-100dB, C
HI (High) – Weighting: 65-130dB,
Resolution 0.1dB Frequency Range 31.5Hz
to 8KHz, Accuracy ±2dB, Dynamic Range
65dB, Frequency Weighting A, C, Time
Weighting Slow & Fast. Maximum Hold
Decay <1dB/3min.
ƒƒ Microphone Electret condenser microphone.
Calibration, Electrical calibration by using the
internal oscillator (1KHz sine Wave at 94dB).
The CScope Cable Avoidance Tool is the classic, industry standard Locator
to use to determine the exact location of buried pipes and cables immediately
prior to any form of excavation work taking place. Hitting and damaging buried
services when excavating is costly and potentially very dangerous. The CScope
Cable Avoidance Tool is the ideal ‘pick-up-and-go’ Locator, to use to locate
buried pipes and cables, quickly and reliably, time after time.
Better by design, the CScope Cable Avoidance Tool is a rugged tool, easily able
to withstand the rigours of life on construction and civil engineering sites and for
utility maintenance work. When combined with a CScope SGA or SGV Signal
Generator and accessories, the Cable Avoidance Tool becomes a versatile,
all round pipe and cable locating and tracing package. Robustly made and
equipped with LCD meter, detachable loudspeaker and easy-to-operate fingertip
controls the CScope Cable Avoidance Tool is the ideal Locator for all levels of
staff who need to be able to detect buried services quickly and with confidence.
CABLE LOCATORS
Cscope MXL/MXT Cable Locator
The new CScope MXL Locator is a high performance locator specifically designed
to detect, identify and trace specific buried pipes and cables reliably and accurately,
even in the most congested areas. It is especially useful for those that wish to
identify the route of a particular pipe or cable.
GAS DETECTOR
Dräger X-AM 2000 with External Pump
The Dräger X-am 2000’s low weight and practical mobile phone design
provides users a high level of comfort and convenience. Thanks to the
practical two-button operation and straightforward menu, the instrument
can be used intuitively.
Used alone, the MXL Locator offers high speed and accurate detection of
most buried services. When used in conjunction with the MXT Transmitter and
accessories, the MXL Locator becomes a high performance pipe and cable locating
and tracing package that will allow long distance and highly selective tracing to
be achieved. It is the ideal locator for those who have to tackle multiple locating
applications in the course of their work.
VIBRATION CALIBRATOR
PROXIMITY SENSOR
CALIBRATOR
CABLE LOCATORS
Bentley Navada TK-3e Proximity Sensor
Calibrator
Used for all applications (live or dead cables) without additional instruments. Set includes
a transmitter and a receiver. Proven digitally coded sender signal guarantees clear
signal identification. Transmitter with LC-display for transmitting level, transmitting code
and external voltage. Receiver with a backlight LC-display for level of receiving signal,
code of receiving signal and live voltage indication. Automatic or manual adjustment of
receiving signal sensitivity. An additional torch/lamp function is useful for working in dark
environments. Additional transmitters are available for extension to distinguish between
several signals.
Modal Shop 9100D Portable Vibration Calibrator
12.
Ideal for checking accelerometers, velocity
transducers and proximity probes over a wide
frequency and amplitude operating range, the
9100D Portable Shaker Vibration Calibrator is
rugged throughout, with simple and elegant
usability and robust internal components. In
contrast to more elaborate laboratory style
systems, the 9100D is a portable vibration shaker
and calibrator, making it perfect for testing in the
field or at a customer’s site.
The unit is small and completely self-contained,
providing a known vibration reference source
from 7Hz (420 CPM) up to 10KHz (600k CPM), at
amplitudes up to 20g (196m/s2), shaker stroke
and sensor mass dependent.
Packaged in a lightweight,
durable Pelican® Case with
two press and pull latches
and padlockable caps, the
9100D is always ready for
travel to test sites.
The specialised
nature of proximity
probe measurements
requires a specialised
calibration instrument,
capable of introducing
fixed gap (i.e.,
position), changing
gap (i.e., vibration), and
rotative speed signals into
the transducer for verification
and testing purposes.
The fixed gap is provided
by clamping the probe into a
stationery position while a movable target on
a spindle micrometer is adjusted. Simulated
vibration is provided by clamping the probe into
a movable swing arm, observing a precision
machined wobble plate that rotates and
introducing a known amount of changing gap
with each rotation. Finally shaft rotative speed
is simulated by observing a Keyphasor notch on
the side of the rotating wobble plate.
Call 1300 736 292 for assistance and advice
GENERAL INDUSTRIAL
SOUND METERS
Fluke 2042 Cable Locator/Tracer
CABLE FAULT LOCATION
Megger TDR2000/2R Time Domain Reflectometer
The MEGGER TDR2000/2 is a state of the art, monochrome, dual channel Time
Domain Reflectometer, capable of identifying and locating a wide range of faults on
metallic cables. The TDR2000/2 has a minimum resolution of 0.1m and a maximum
range of 20km at VF=0.9 and 16kM at 0.65VF. The TDR2000/2 can perform single
or dual channel measurements on a wide range of metallic cables. Active channels
can be compared with each other or with previously stored traces from memory.
Differential channel measurements are possible and cross talk between channels
can also be identified. All results are displayed on a high resolution, QVGA display.
Full contrast adjustment provides optimum display contrast in a variety of ambient
light conditions. The TDR2000/2 can display either single or dual cursors. Single
cursor mode displays the distance from the start of the cable to the cursor. In dual cursor mode the distance
between faults can be measured. One press of the find key automatically adjusts the range and gain and
positions the cursor to the major event on the cable.
Email [email protected] for additional information
13.
ENVIRONMENTAL
LIGHT METERS
Emerson Rosemount 375 Field Communicator HART & Fieldbus
Tektronix TPS2014 Digital Colour 100Mhz Scopemeter
The Emerson Rosemount 375 field communicator has support for HART and
FOUNDATION fieldbus devices. Easy upgrade delivers the ability to keep your system
software and device drivers updated through the web. Enhanced graphics enable
you to view your diagnostics information in charts, graphs, gauges, and pictures for
quicker diagnosis. Increased battery life from the Lithium-Ion Power Module gives you
days of power. With over 1,200 devices supported, the 1GB system card gives you
the memory capacity to have all the Device Descriptions (DDs) you need.
ƒƒ
ƒƒ
ƒƒ
ƒƒ
COMMUNICATORS
Emerson 475 Field Communicator HART & Fieldbus
Full-colour graphical user interface supports graphs, charts, gauges, and pictures
for quicker diagnosis. Gain powerful device diagnostics in the field to enable
troubleshooting. Efficiently and consistently manage configurations through easy
transfer between the communicator and your PC. Long-lasting Lithium-Ion power
module delivers days – not hours – of power. The 475 has universal support
for HART, WirelessHART, and FOUNDATION fieldbus devices. It has localized
language support for English, German, and Russian. Easy Upgrade delivers the
ability to keep your system software and device drivers updated through the web.
Bluetooth communication speeds transfer of information.
OSCILLOSCOPES
Fluke 123 Digital 20Mhz 600V Scopemeter
In today’s complex systems, a meter measurement just doesn’t give enough
detail to determine the cause of a fault. Signal anomalies, dropouts and glitches
that might cause a machine to go down, are best displayed with an oscilloscope.
The Fluke 123 Scopemeter meets today need of simultaneously measuring and
checking waveforms. For industrial, electronic or electro mechanical applications,
the compact Fluke 123 Industrial Scopemeter is the rugged solution for industrial
troubleshooting and installation applications. It features 20MHz bandwidth,
Connect-and-View triggering automatically displaying stable waveforms of virtually
any signal with a dual DMM/paperless recorder to get virtually any job done.
OSCILLOSCOPES
Fluke 199C Digital Colour 200Mhz 1000V Scopemeter
14.
Whether you are performing routine maintenance and calibration, or troubleshooting
the hardest to solve problems like intermittent failures or sources of unwanted noise,
the Fluke 199C Colour Scopemeter has all the tools needed to get the job done. With
200MHz bandwidth, up to 2.5GS/s real-time sampling rate and 27500 points memory
for high resolution waveform per input they’re ideal for engineers who need the full
capabilities of a high-performance oscilloscope in a handheld, battery powered
instrument. This model has a high resolution colour display that has a fast update
rate, waveform pass/fail testing and a digital persistence mode – making the analysis
of complex and dynamic signals that much easier.
Call 1300 736 292 for assistance and advice
ƒƒ
ƒƒ
ƒƒ
ƒƒ
ƒƒ
ƒƒ
ƒƒ
100MHz Bandwidth.
1GS/s Real Time sample rate.
2.5K Record Length.
Has 4 Fully Isolated and Floating Channels,
plus Isolated External Trigger.
8 Hours of Continuous Battery Operation with Two Batteries Installed.
Hot-swappable for Virtually Unlimited Freedom from an AC Power Source.
Quickly Document and Analyse Measurement Results with OpenChoice® Software or Integrated
Compact Flash Mass Storage.
FFT is Standard. Includes Advanced Triggers to Quickly Capture the Event of Interest.
Easily Operate the Oscilloscope with Traditional, Analog-style Knobs and Multilanguage User Interface.
Simplify Setup and Operation with Autoset Menu, Autorange, Waveform and Setup Memories, and
Built-in, Context-sensitive Help.
Adjust the Oscilloscope to Your Operating Environment with Backlit Menu Buttons/Display and
Brightness/Contrast Controls.
PROCESS CALIBRATORS
GENERAL INDUSTRIAL
OSCILLOSCOPES
Beamex MC5-E-ET-RJ Multifunction Calibrator with Fieldbus
Due to its all-in-one functionality, the MC5 replaces several individual devices
and calibrators. This also reduces recalibration costs, as you only need
to maintain one device instead of several. Calibrate fieldbus transmitters:
Although modern fieldbus transmitters have been improved compared to
older transmitter models, it does not eliminate the need for calibration. The
MC5 Fieldbus Calibrator is a combination of a multifunction calibrator and
a fieldbus configurator. The MC5 is a high accuracy calibrator. Each MC5
calibrator is delivered with a traceable, accredited calibration certificate. The
MC5 has IP65-rated robust casing with integrated impact protectors. The
modular construction of the MC5 provides flexibility. Calibration results are
automatically stored in the memory of the MC5 and automatically transferred
from the memory to calibration software. This provides you with a complete
documenting system that produces calibration certificates automatically.
PROCESS CALIBRATORS
PROCESS CALIBRATORS
Fluke 726 Process Calibrator
Fluke 744 Logging Process Calibrator
The Fluke 726 Precision
Multifunction Process
Calibrator is designed
specifically for the Process
industry with broad workload
coverage, calibration
power and unsurpassed
accuracy in mind. The
Fluke 726 measures and
sources almost all process
parameters and can calibrate
almost anything. The Fluke
726 will also interpret results
without the help of a calculator and
store measurement data for later analysis.
The Fluke 744 is a power
multifunction documenting
calibrator that lets you
download procedures, lists,
and instructions created
with software-or upload data
for printing, archiving, and
analysis. The Fluke 744 also
features a powerful built in
HART interface capable of
performing nearly all the
day-to-day tasks you now
perform with a separate
communicator.
Email [email protected] for additional information
15.
GENERAL INDUSTRIAL
COMMUNICATORS
PRESSURE CALIBRATORS
Pruftechnik AG ALI5.200 Optalign Plus
Crystal XP2i Pressure Calibrator
The OPTALIGN PLUS Series control unit is built to rugged industrial standards of shock
and water resistance (IP65). It features an easy-to-read, energy-saving fixed segment
LCD display that shows all important measurement steps such as dimensions and
results. An intelligent power management system saves battery life by putting the
control unit to ‘sleep’ after several minutes of non-use. The built-in reserve battery
ensures that the job at hand can be completed. The control unit powers the transducer
and receives measurement data via cable. The robust flat keyboard is designed for
especially simple operation; those keys which are needed less often are located beneath
a sliding cover. A serial interface allows direct connection to a PC or printer, OPTALIGN
PLUS Explorer, is available to store and analyse results. An external PC program lets
you load the latest software version into the OPTALIGN PLUS Series to update the
transducer system at any time.
Ultra rugged, intrinsically safe, digital pressure test gauge with 0.1% of reading
accuracy. Marine grade enclosure resists corrosion. Accuracy not affected from
-10 to 50°C. Replaces 5 or more digital test gauges. Records 6000 points
with DataLoggerXP. Fast pressure safety valve (PSV) mode. Define custom
pressure units.
VIBRATION ANALYSERS
Commtest VB7 Vibration Analyser
The VB7 instrument is an all-in-one tool suitable for every level of vibration
analyst, from novice through to expert. The Ascent® software contains the
collective experience of over 25 years of expert in-depth machine fault analysis.
Just one of the VB7 instrument enhancements that must be experienced
first-hand is its amazing light weight. The VB7 instrument offers true twochannel on-route data collection with collection speed further maximized
by Commtest’s unique adaptive settling technology. In addition, the VB7
instrument offers a battery life of over ten hours, fast data transfer via USB
and Ethernet, and a massive 1GB of onboard memory.
Available in the following ranges, 100psi, 300psi, 5000psi, 10000psi.
PRESSURE CALIBRATORS
Druck DPI620 Advanced Pressure Calibrator 1000bar
The GE Druck DPI 620 uses three basic components to perform multiple
calibration functions that formerly required a wide range of different instruments.
The basic component of this system is the GE Druck DPI 620 multifunction
calibrator, an ultra-compact, electrical, frequency, and temperature calibrator,
which provides simultaneous measurement and source capabilities. Pressure
measurement is provided by interchangeable pressure modules that can
be attached to the calibrator by a pressure module carrier. Inside is a fully
functional HART field communicator, replacing the need for a stand-alone
HART communication unit. If pressure generation is required, the calibrator and
pressure module can be attached to one of three pressure generation stations,
to form a high performance, full-integrated pressure calibrator.
GENERAL INDUSTRIAL
GENERAL INDUSTRIAL
LASER ALIGNMENT
TEMPERATURE CALIBRATORS
VIDEOSCOPE
Olympus IV7630X2 Videoscope
The IPLEX MX R supplies a slim ø6.0mm outer diameter tube
with a short 21.4mm hard tip and a small curvature radius for
effortless insertion ease and convenient access to minute parts.
It’s especially effective for high-precision jobs in intricate spaces,
such as inspecting small gas turbines and heat exchanger tubes.
The Olympus-original “Tough Tapered Flex” insertion tube design
provides superior insertability, and excellent crush resistance
increases equipment reliability.
MANOMETERS
Fluke 9009 Dry Well Calibrator -15 Deg C to 350 Deg C
The Fluke 9009 includes two independently controlled temperature
blocks. The hot block provides temperatures from 50°C to 350°C,
while the cold block covers the range -15°C to 110°C. Each block is
controlled by a precision HART Scientific temperature controller. These
aren’t some off-the-shelf controllers glued into a box. These are HART
Scientific controllers from the leading temperature company in the world.
Each temperature block includes two wells with removable inserts. You
can calibrate four probes at once, or you can calibrate two probes at
the same time with an external reference (like HART’s Model 1521 LLK
Thermometer), or you can use the two temperature wells to get quick “zero” and “span” references for
transmitter calibrations. Need portability and durability? The 9009 is housed in a tough Pelican™ case that
is both airtight and watertight. It’s a small package weighing only 4.5kg, yet it fits everything you need,
including a power cord and four extra inserts. Inserts are available to accommodate sensors of any size
from 1/16” (1.6mm) to 7/16” (11.1mm). This rugged system can go anywhere.
Digitron 2021P Digital Manometer 130mbar
TEMPERATURE CALIBRATORS
Fluke 9173 Dry Well Calibrator 50 Deg C to 700 Deg C
For work between 50°C and 700°C, the HART Scientific Model 9173 metrology
well calibrator provides unmatched performance. The HART Scientific Model
9173 has a display accuracy of ±0.25°C at 700°C and an immersion depth of
203mm. Stability and uniformity performance of the HART Scientific Model 9173
metrology well calibrator are enough to dramatically reduce uncertainty budgets
for calibrations of thermometers at high temperatures. Temperature range from
50°C to 700°C.
Best-performing industrial heat sources (accuracy, stability, uniformity) in the world.
Call 1300 736 292 for assistance and advice
Email [email protected] for additional information
17.
16.
Low pressure measurement to 130mbar. Measurements in Pa, in H20, m H20, in Hg,
m Hg & PSI. The 2000 Series of pressure instruments offer a wide range of handheld manometers. Easy to operate, reliable and built to last, the 2000 series has been
developed in order to meet the performance and cost demands of today’s markets.
New innovative functions designed to make the operator’s job easier set new standards
in pressure measurements. All units have a clear, backlit LCD display, data hold and a
typical battery life of 200 hours.
Flir Thermacam T360 Thermographic Camera
The new T-Series infrared camera from FLIR Systems is unlike anything you’ve
ever seen. It’s super compact and ultra light. It communicates with its software
and with the world around it in a way that’s truly outstanding. And, with unique
features like a touch screen, text- and sketch annotation, a tiltable lens unit
and application-specific alarm functions, it’s incredibly easy to use. We’ve also
included many other great features like an integrated digital camera, or an
infrared and visual image fusion function.
Precise Calibration is experienced in the calibration of test and measurement
equipment and instrumentation.
With laboratories in Perth and Brisbane, we offer
traceable calibrations to Australian National
Standards. All calibration reports are issued in
compliance with ISO/IEC 17025 and we are able
to offer fast turnaround times to our customers.
Our service covers the following fields:
THERMOGRAPHIC CAMERAS
THERMOGRAPHIC CAMERAS
ƒƒ Electrical Test & Measurement Equipment –
LV and HV.
Fluke Ti32 Thermo Camera with 2x Lenses
Flir E45 Thermographic Camera
The new Fluke Ti32 thermal
imager combines a powerful
320x240 FPA sensor with field
upgradeable lenses, removable
batteries, and many new features.
Built on the award winning design
of the Fluke Ti25 family, these
new imagers deliver amazingly
clear image quality in a package
that will withstand the toughest
environments. Intended for
industrial applications the Fluke
Ti32 allows customers to find, fix
and prove problems and repairs
fast. Includes wide and
telephoto lenses.
The camera has extremely
high thermal sensitivity.
Unparalleled image quality.
Useable in all weather
conditions (IP54). Records
images at a ‘frame rate’ of
50Hz. Standard JPEG image
storage (up to 200 images). A
wide range of accessories and
lenses are available. Short focus
distance.
ƒƒ Temperature – Direct & Infrared.
ƒƒ Pressure Calibrations – Pneumatic & Hydraulic.
With the latest up to date calibrators our experienced team delivers instrument
calibration services to customers in Oil & Gas, Mining and Industrial sectors.
Our scope includes calibration of the following instrumentation:
ƒƒ Analogue and Digital Multimeters up to 6½ digit
(1050V AC/DC and up to 1000A AC/DC)
ƒƒ IR Thermometry -15°C to 500°C
ƒƒ Chart Recorders
ƒƒ Optical Tachometers
ƒƒ Clamp Meters up to 5000A AC/DC
ƒƒ Portable Appliance Testers
ƒƒ CT Analysers
ƒƒ Data Loggers
ƒƒ Pressure Calibrators and Digital Test Gauges
from -1bar to 1200bar
ƒƒ Digital Temperature Meters
ƒƒ Power Quality Analysers Single and 3 Phase
ƒƒ High Voltage Test Sets to 150KV AC/DC
ƒƒ Process Instrumentation/Calibrators
Hioki 8847 Waveform Recorder
ƒƒ Hipot/VLF Testers to 150KV AC/DC
ƒƒ Relay Test Sets
ƒƒ
ƒƒ
ƒƒ
ƒƒ
ƒƒ HV PPE Testing & PPE Certification Equipment
ƒƒ Substation Test Sets
ƒƒ Injection Sets
ƒƒ Thermal Cameras
ƒƒ Installation Testers (Earth, Loop, RCD)
ƒƒ Transformer Turns Ratio Testers
ƒƒ Insulation Testers up to 10,000V
ƒƒ Dry Block Calibrators/Temperature Baths
Compatible with THERMACAM™
REPORTER™ Software.
THERMACAMQUICKVIEW™ included.
WAVEFORM RECORDERS
ƒƒ
ƒƒ
ƒƒ
ƒƒ
ƒƒ
ƒƒ
ƒƒ Micro-ohmmeters
If your equipment is not listed above do not hesitate to contact us directly to see
if it can be calibrated.
18.
ƒƒ
High-speed sampling up to 20MS/s with fully isolated inputs.
16 analog +16 logic channels to 64 logic +10 analog channels.
Large, tough handle makes carrying a snap.
Soil-resistant construction is strong against adverse working
environments.
Big buttons are coated to withstand industrial oil and residue.
Drop-in paper loading and one-touch setup, along with high 50mm/s
printing speed.
Built-in LAN and USB interfaces.
Supports instantaneous waveform observation and recording, for
example to monitor commercial power supply lines.
Transient waveform events such as caused by motor inrush current can also easily be recorded.
Start measurement without reading through the manual; The Help Wizard assists you to do exactly
what you want.
Print out results on the spot.
PRECISE CALIBRATION
GENERAL INDUSTRIAL
THERMOGRAPHIC CAMERAS
Precise
Pr
F A C I L I T I E S
F A
Call 1300 736 292 for assistance and advice
Email [email protected] for additional information
ALL OFFICES
Email: [email protected]
WESTERN AUSTRALIA
QUEENSLAND
VICTORIA
Perth Head Office
Present Group, Octave Consulting,
Seamless Resourcing
Brisbane
Present Group, Octave Consulting,
Seamless Resourcing, Powertech Services,
Precise Facilities
Melbourne
Address: 3 Scholar Drive,
Bundoora VIC 3083
Address: 507 Murray Street,
Perth WA 6000
Phone: +61 8 9244 4477
Osborne Park
Powertech Services, Precise Facilities
Address: 6/8 Hasler Road,
Osborne Park WA 6017
Powertech Services: +61 8 9244 4477
Precise Facilities: 1300 736 292 &
Address: 3-4 70 Fison Ave West,
Eagle Farm QLD 4009
Phone: +61 7 3268 1378
Gladstone
Address: 4 Helen Street,
Gladstone QLD 4680
Phone: +61 3 9036 0930
NEW SOUTH WALES
Newcastle
Address: 4/12 Channel Road,
Mayfield West NSW 2304