Gas Heating Controls

Transcription

Table of Contents
Categorized Listing
REFRIGERATION & AIR CONDITIONING
Compressors
Refrigerant Handling Equipment
AIR CONDITIONING & HEATING CONTROLS
Thermostats
Air Conditioning & Refrigeration Controls
Electric Heating Controls
Oil Heating Controls
Hydronic Heating Controls & Gas Water Heater Valves
HVAC Components
VENTILATION & INDOOR AIR QUALITY
Indoor Air Quality
Indoor Air Quality Products
Indoor Air Quality
Indoor Air Quality
Zoning, Venting & Economizer Controls
Duct Connectors
Insulation Fasteners
MOTORS & MOTOR ACCESSORIES
Source 1 Motors
Timesaver Multi-HP PSC Motors
Timesaver Multi-HP PSC Motors Capacitor Guide
AO Smith Motors
Century Electric Motors
Dayton Motors
Genteq Motors
Capacitors
Fan Blades
Blower Wheels
Rainshields
Bearings
Mounting Brackets
Sheaves
Bushings
Source 1 V-Belts
INSTALLATION & MAINTENANCE SUPPLIES
Installation Accessories
Water Heater Installation Accessories
Screws & Fasteners
Linesets, Fittings & Copper Tubing
Minisplit Installation Accessories
Black Pipe & Fittings
PVC Pipe & Fittings
Welding Equipment & Supplies
HVAC Sundries
Markers
CHEMICALS
HVAC System Hygiene
1
1
20
41
41
68
78
103
105
107
109
145
145
149
149
150
151
158
172
172
173
177
177
179
181
182
188
193
195
196
196
199
199
200
200
202
204
212
212
225
225
248
248
252
254
256
259
260
260
268
273
276
291
296
300
305
305
Table of Contents
Categorized Listing
Air-Cooled Equipment & Filter Cleaning
HVAC System Hygiene
Super Concentrated Coil Cleaners
HVAC System Hygiene
Sprayers
Leak Detector & Insecticide
Specialty Products & Aerosols
Gas Leak Detectors
HVAC System Hygiene
Coil Protection
Corrosion Protection Products
IAQ Assurance
IAQ Assurance
Condensate Drain Pan Strips, Tabs & Lubricants
Condensate Drain Strips, Tabs & Lubricants
Drain Tabs & Lubricants
IAQ Assurance
Lubricants & Flushing Solvents
System Flushing
System Protection
Acid Test Kit & PVC Sealants
Lubricant Products
Refrigeration Oils
Vacuum Pump Oil
Lubricant Products
Lubricants
Oatey Cutting Oil
Caulk, Caulk Guns & Pipe Joint Compound
Furnace Cement
Furnace Cement, Smoke Cartridges, Insulation Tape & Gum
Insulation Products
Insulation Products
Pipe Joint Compound, Foam Sealant & Firestop Products
Solvent Based Duct Adhesives
Solvent Based Duct Sealant
Solvent Based Insulation Adhesive
Water Based & Solvent-Free Duct Adhesives
Water Based Duct Sealants
Water Based Insulation Adhesive
Solvent Based Duct Sealants
Water Based & Solvent-Free Duct Sealants
Sealants, Epoxies & Glues
306
306
306
307
307
307
308
308
311
311
312
312
312
313
313
314
314
315
315
318
319
320
321
321
321
322
323
324
324
325
326
326
327
327
329
329
329
330
330
333
333
335
336
336
336
337
337
340
340
341
342
342
343
345
346
347
347
348
350
351
352
352
Table of Contents
Categorized Listing
Elastomeric Tape/Rolled Sealant
Insulation Products
Tape & Tape Dispensers
Tapes
HVAC System Hygiene
Paints & Primers
Contact Cleaners
Degreasing Solvents
Galvanizing Compound Sprays
Hand Cleaners
Personal Hygiene
Closed System & Glycol Water Treatment
Cooling Tower Water Treatment
Everpure Products
Feeding Equipment
Ice Machine Cleaning & Filtration
Scale Removal/Descaling
Windshield Washer Fluid
ELECTRICAL ACCESSORIES
Cable Clamps & Ties
Compressor Terminals & Alligator Clips
Connectors
Connectors & Fittings
Connectors, Fittings, Cable Staples, Switches & Plugs
Disconnects
Disconnects & High Temperature Terminals
Disconnects & Rings
Electrical Outlet Boxes, Extensions & Covers
Fuses, Electrical Outlet Boxes, Extensions & Covers
Fuses
High Temperature Solderless Terminals
Hook Terminals
Leads & Compressor Repair Kits
Monitors
Pigtails
Receptacles & Circuit Breakers
Rings
Slip-Ons
Spade Terminals
Spade Terminals & Slip-Ons
Special Purpose Solderless Terminals
Square D Air Conditioning Disconnects
Storage Boxes
Waterproof Solderless Terminals
Whips
Wire
Wire Ties
353
353
354
354
356
356
357
358
359
360
360
361
362
362
363
364
364
364
365
366
368
368
368
369
370
371
371
372
373
373
377
377
378
379
380
382
385
387
389
390
391
392
392
396
397
398
398
399
399
400
403
405
407
409
410
411
411
412
413
413
415
Table of Contents
Categorized Listing
TEST INSTRUMENTS & TOOLS
Test Instruments
Tools
417
417
429
Compressors
BRISTOL COMPRESSORS
1
Compressors
BRISTOL COMPRESSORS
H2EB Series
SOURCE 1 PART NO.
BRISTOL
MODEL NO.
CAPACITY
BTUH
S1-H2EB18SABCB
S1-H2EB24SABCB
S1-H2EB283ABCB
H2EB18SABCB
H2EB24SABCB
H2EB283ABCB
17600
23600
28100
V-PH-HZ
RLA LRA EER SUCT DISCH SUCT DISCH OVALL CCH
ID (IN.) ID (IN.) HT (IN.) HT (IN.) HT (IN.)
230-208/1/60 10.2
230-208/1/60 13
230-208/1/60 13.5
60
72
85
9.1
9.4
9.1
5/8 E
5/8 E
5/8 E
2
3/8 E
3/8 E
3/8 E
12.094
12.719
12.719
2.859
2.859
2.859
12.516
13.141
13.141
RUN START CAP SHIP
CAP
WT.
(LBS.)
NO 25/370 145-175/250 59.58
NO 30/370 145-175/250 63.08
NO 45/370 145-175/25 70.68
MLP $
658.32
790.50
828.75
Compressors
BRISTOL COMPRESSORS
H22A Series
SOURCE 1 PART NO.
BRISTOL
MODEL NO.
CAPACITY
BTUH
V-PH-HZ
S1-H22A503ABCA
S1-H22A503DBEA
S1-H22A503DBFA
S1-H22A503DBLA
S1-H22A543ABCA
S1-H22A543DBEA
S1-H22A543DBFA
S1-H22A543DBLA
S1-H22A563DBLA
S1-H22A583ABCA
S1-H22A583DBEA
S1-H22A623ABCA
S1-H22A623DBEA
S1-H22A623DBFA
S1-H22A623DBLA
H22A503ABCA
H22A503DBEA
H22A503DBFA
H22A503DBLA
H22A543ABCA
H22A543DBEA
H22A543DBFA
H22A543DBLA
H22A563DBLA
H22A583ABCA
H22A583DBEA
H22A623ABCA
H22A623DBEA
H22A623DBFA
H22A623DBLA
49000
49000
49000
49000
53419
55000
53419
53419
55600
57122
58083
60795
58885
60795
60795
208/230-1-60
460-3-60
575-3-60
230/200-3-60
208/230-1-60
460-3-60
575-3-60
230/200-3-60
230/200-3-60
208/230-1-60
460-3-60
208/230-1-60
460-3-60
575-3-60
230/200-3-60
RLA LRA EER SUCT DISCH SUCT DISCH OVALL CCH *RUN START CAP SHIP
CAP
WT.
(LBS.)
22.3 138 10.0
7/8
1/2
14.00 3.312 16.406 YES 40/440 135-155/330 92.0
6.8 53 10.0
7/8
1/2
14.00 3.312 16.406 YES N/A
N/A
84.0
5.5 43 10.0
7/8
1/2
14.00 3.312 16.406 YES N/A
N/A
84.0
13.7 106 10.0
7/8
1/2
14.00 3.312 16.406 YES N/A
N/A
84.0
24.1 138 10.3
7/8
1/2
14
3.312
16.4 YES 45/440 135-155/330 92.0
7.3 53 10.5
7/8
1/2
14
3.312
16.4 YES N/A
N/A
84.0
5.8 43 10.5
7/8
1/2
14
3.312
16.4 YES N/A
N/A
84.0
14.5 106 10.5
7/8
1/2
14
3.312
16.4 YES N/A
N/A
84.0
15.3 124 10.4 7/8 S
1/2 E
14
3.312 16.125 YES N/A
N/A
93.29
26.6 178 10.19 7/8
1/2
14
3.312
16.4 YES 60/370 270-324/330 97.5
7.9 62 10.81 7/8
1/2
14
3.312
16.4 YES N/A
N/A
87.5
28.2 178 10.3
7/8
1/2
14
3.312
16.4 YES 55/440 135-155/330 97.5
8.5 62 9.78
7/8
1/2
14
3.312
16.4 YES N/A
N/A
87. 5
6.8 50 10.5
7/8
1/2
14
3.312
16.4 YES N/A
N/A
87.5
17 124 10.5
7/8
1/2
14
3.312
16.4 YES N/A
N/A
87.5
* NOTE: When substituting compressors always check the capacitor MFD and voltage (when required) and
replace if necessary. The capacitor MUST be the proper MFD and voltage for the compressor.
3
MLP $
1152.04
1335.89
1371.46
1335.89
1143.07
1354.21
1390.25
1354.21
1363.18
1235.96
1372.11
1196.04
1442.46
1442.46
1442.46
Compressors
BRISTOL COMPRESSORS
H22G Series
SOURCE 1 PART NO.
BRISTOL
MODEL NO.
CAPACITY
BTUH
S1-H22G094DBDE
H22G094DBDE,
ROTOLOCK
H22G094DBEE,
ROTOLOCK
H22G094GPEE,
ROTOLOCK
H22G104DBDE,
ROTOLOCK
H22G124DBDE,
ROTOLOCK
H22G124DBEE,
ROTOLOCK
H22G124GPDE,
ROTOLOCK
H22G124GPEE,
ROTOLOCK
H22G144DBDE,
ROTOLOCK
H22G144DBEE,
ROTOLOCK
H22G184DPEF,
ROTOLOCK
H22G184GPDF,
ROTOLOCK
H22G184GPEF,
ROTOLOCK
H22G204DREF,
ROTOLOCK
H22G244DREF,
ROTOLOCK
H22G244GPDF,
ROTOLOCK
H22G244GPEF,
ROTOLOCK
H22G294DPEF,
ROTOLOCK
88700
S1-H22G094DBEE
S1-H22G094GPEE
S1-H22G104DBDE
S1-H22G124DBDE
S1-H22G124DBEE
S1-H22G124GPDE
S1-H22G124GPEE
S1-H22G144DBDE
S1-H22G144DBEE
S1-H22G184DPEF
S1-H22G184GPDF
S1-H22G184GPEF
S1-H22G204DREF
S1-H22G244DREF
S1-H22G244GPDF
S1-H22G244GPEF
S1-H22G294DPEF
V-PH-HZ
RLA LRA EER SUCT ID DISCH ID SUCT DISCH OVALL CCH *RUN START SHIP
(IN.)
(IN.)
HT (IN.) HT (IN.) HT (IN.)
CAP
CAP
WT.
(LBS.)
230/208-3-60 24 145 10.3 1-3/4 x 12 1-1/4 x 12
9
9
17.594 YES N/A
N/A 155.09
MLP $
3855.86
88700
460-3-60
12.3
72
10.3 1-3/4 x 12 1-1/4 x 12
9
9
17.594 YES
N/A
N/A
155.09
3662.61
87700
460-3-60
12.7
70
10.1 1-3/4 x 12 1-1/4 x 12
9
9
17.094 YES
N/A
N/A
177.3
5992.68
103900
230/208-3-60 29.3 166 10.4 1-3/4 x 12 1-1/4 x 12
9
9
18.344 YES
N/A
N/A
171.39
4380.96
121500
230/208-3-60 36
205 10.1 1-3/4 x 12 1-1/4 x 12
9
9
18.344 YES
N/A
N/A
167.09
4615.71
85
9.9 1-3/4 x 12 1-1/4 x 12
9
9
18.344 YES
N/A
N/A
167.09
4615.71
230/208-3-60 36.2 192
9.6 1-3/4 x 12 1-1/4 x 12
9
9
17.844 YES
N/A
N/A
187.3
6454.82
9.6 1-3/4 x 12 1-1/4 x 12
9
9
17.844 YES
N/A
N/A
187.3
6549.79
9
20.584 YES
9
119000
119400
119400
140000
460-3-60
460-3-60
17
18.1
96
N/A
N/A
189.99
4945.79
140000
460-3-60
21.6 126 10.1 1-3/4 x 12 1-1/4 x 12 18.198
20.584 YES
N/A
N/A
189.99
5066.60
183200
460-3-60
25.9 117 10.3 1-3/4 x 12 1-1/4 x 12 11.297 11.797 21.750 YES
N/A
N/A
266.1
8526.79
230/208-3-60 51.3 248 10.3 1-3/4 x 12 1-1/4 x 12 11.297 11.797 21.750 YES
N/A
N/A
266.1
9064.64
N/A
N/A
266.1
8964.25
182300
230/208-3-60 43.1 252 10.1 1-3/4 x 12 1-1/4 x 12 18.198
182300
460-3-60
212400
460/3/60
252900
460/3/60
253500
25.6 124 10.3 1-3/4 x 12 1-1/4 x 12 11.297 11.797 21.750 YES
N/A
N/A
273.1
9214.14
36.6 180
30
141 10.2 1-3/4 x 12 1-1/4 x 12 11.297 11.797 21.750 YES
10 1-3/4 x 12 1-1/4 x 12 11.297 11.797 21.750 YES
N/A
N/A
282.1
9166.50
230/208-3-60 73.1 362
9.9 1-3/4 x 12 1-1/4 x 12 11.297 11.797 21.750 YES
N/A
N/A
282.1
9166.86
253500
460/3/60
36.6 181
9.9 1-3/4 x 12 1-1/4 x 12 11.297 11.797 21.750 YES
N/A
N/A
282.1
9456.14
287400
460/3/60
43.9 200
9.5 1-3/4 x 12 1-1/4 x 12 11.297 11.797 21.750 YES
N/A
N/A
293.1
9440.89
4
Compressors
BRISTOL COMPRESSORS
H22J Series
SOURCE 1 PART NO.
BRISTOL
MODEL NO.
CAPACITY
BTUH
V-PH-HZ
S1-H22J13BABCA
S1-H22J15BABCA
S1-H22J18BABCA
S1-H22J18BABHA
S1-H22J20BABCA
S1-H22J22BABCA
S1-H22J22BABHA
S1-H22J253DBLA
S1-H22J253DBVA
S1-H22J25BABCA
S1-H22J25BABHA
S1-H22J293DBFA
S1-H22J293DBLA
S1-H22J293DBVA
S1-H22J29BABCA
S1-H22J333DBFA
S1-H22J333DBLA
S1-H22J333DBVA
S1-H22J33BABCA
S1-H22J363DBFA
S1-H22J363DBLA
S1-H22J363DBVA
S1-H22J36BABCA
S1-H22J36BABHA
S1-H22J383DBFA
S1-H22J383DBLA
S1-H22J383DBVA
S1-H22J38BABCA
S1-H22J413DBEA
S1-H22J413DBFA
S1-H22J413DBLA
S1-H22J41BABCA
S1-H22J443DBDA
S1-H22J443DBEA
S1-H22J443DBFA
S1-H22J44BABCA
H22J13BABCA
H22J15BABCA
H22J18BABCA
H22J18BABHA
H22J20BABCA
H22J22BABCA
H22J22BABHA
H22J253DBLA
H22J253DBVA
H22J25BABCA
H22J25BABHA
H22J293DBFA
H22J293DBLA
H22J293DBVA
H22J29BABCA
H22J333DBFA
H22J333DBLA
H22J333DBVA
H22J33BABCA
H22J363DBFA
H22J363DBLA
H22J363DBVA
H22J36BABCA
H22J36BABHA
H22J383DBFA
H22J383DBLA
H22J383DBVA
H22J38BABCA
H22J413DBEA
H22J413DBFA
H22J413DBLA
H22J41BABCA
H22J443DBDA
H22J443DBEA
H22J443DBFA
H22J44BABCA
13300
15485
18265
18100
22500
22622
22700
23530
23613
24214
23600
28800
27964
27769
28833
33032
32352
31600
31946
34093
35049
34352
35681
35500
37517
37517
37517
37829
41570
40428
40546
40929
44126
44126
44126
44325
230-208/1/60
208/230-1-60
208/230-1-60
265/1/60
230-208/1/60
208/230-1-60
265/1/60
230/200-3-60
460/380-3-60
208/230-1-60
265/1/60
575/3/60
230/200-3-60
460/380-3-60
208/230-1-60
575-3-60
230/200-3-60
460/380-3-60
208/230-1-60
575-3-60
230/200-3-60
460/380-3-60
208/230-1-60
265/1/60
575-3-60
230/200-3-60
460/380-3-60
208/230-1-60
460-3-60
575-3-60
230/200-3-60
208/230-1-60
230/208-3-60
460-3-60
575-3-60
208/230-1-60
RLA LRA EER SUCT DISCH SUCT DISCH OVALL CCH *RUN START CAP SHIP
CAP
WT.
(LBS.)
6
48 10.4 3/4 S
1/2 E 11.234 2.875 13.25 YES 30/370 161-193/250 72.98
6.7 48 10.81 3/4
1/2
11.234 2.875
13.5 YES 30/370 161-193/250 63.0
7.4 48 11.02 3/4
1/2
11.234 2.875
13.5 YES 30/370 161-193/250 63.0
6.5 44 10.7 3/4 S
1/2 E 11.234 2.875 13.25 YES 25/440 88-108/330 73.08
8.6 60 10.8 3/4 S
1/2 E 11.734 2.875 13.75 YES 30/370 145-175/250 71.58
9.6 48 11.02 3/4
1/2
11.234 2.875 14.03 YES 30/370 145-175/250 64.5
8.2 58
11
3/4 S
1/2 E 11.734 2.875 13.75 YES 30/440 88-108/330 73.58
3.2 58 11.12 3/4
1/2
11.734 2.875
14
YES N/A
N/A
63.0
3.4 30 11.12 3/4
1/2
11.734 2.875
14
YES N/A
N/A
64.5
9.6 60 11.23 3/4
1/2
11.734 2.875
14
YES 35/370 145-175/250 67.0
8.3 58 11.2 3/4 S
1/2 E 11.734 2.875 13.75 YES 30/440 88-108/330 75.58
3.7 32
11
3/4 S
1/2 E
12.2
2.9
14.20 YES
NA
NA
77.48
7.8 68 11.23 3/4
1/2
11.734 2.875
14
YES N/A
N/A
66.5
4.1 38 10.91 3/4
1/2
11.734 2.875
14
YES N/A
N/A
66.0
11.8 73 11.23 3/4
1/2
11.734 2.875
14
YES 35/370 161-193/250 67.5
3.7 32 11.02 3/4
1/2
12.234 2.875
14.5 YES N/A
N/A
70.5
9
78 11.33 3/4
1/2
12.234 2.875
14.5 YES N/A
N/A
71.0
4.5 40 11.12 3/4
1/2
12.234 2.875
14.5 YES N/A
N/A
71.0
13
62 11.23 3/4
1/2
12.234 2.875
14.5 YES 40/370 145-175/250 72.0
3.9 32 10.81 3/4
1/2
12.234 2.875
14.5 YES N/A
N/A
71.0
9.6 78 11.02 3/4
1/2
12.234 2.875
14.5 YES N/A
N/A
71.0
4.9 40 10.81 3/4
1/2
12.234 2.875
14.5 YES N/A
N/A
71.0
14.4 86 11.23 3/4
1/2
12.234 2.875
14.5 YES 45/370 145-175/250 73.5
13
90 10.8 3/4 S
1/2 E 12.234 2.875 14.25 YES 35/440 88-108/330 80.08
4
36 11.7
3/4
1/2
13.969 4.125
15.8 YES N/A
N/A
80.0
10.2 88 11.5
3/4
1/2
13.969 4.125
15.8 YES N/A
N/A
80.0
5
42 11.7
3/4
1/2
13.969 4.125
15.8 YES N/A
N/A
80.0
14.9 86 11.54 3/4
1/2
13.969 4.125
15.8 YES 45/370 189-227/250 84.0
5.4 42 11.4
3/4
1/2
13.969 4.125
15.8 YES N/A
N/A
80.0
4.3 36 11.63 3/4
1/2
13.969 4.125
15.8 YES N/A
N/A
80.0
11
88 11.84 3/4
1/2
13.969 4.125
15.8 YES N/A
N/A
80.0
17.1 102 11.4
3/4
1/2
13.969 4.125
15.8 YES 50/370 216-259/330 84.0
11.7 88 11.4
3/4
1/2
13.969 4.125
15.8 YES N/A
N/A
80.0
5.8 42 11.74 3/4
1/2
13.969 4.125
15.8 YES N/A
N/A
80.0
4.6 36 11.74 3/4
1/2
13.969 4.125
15.8 YES N/A
N/A
80.0
17.8 102 11.4
3/4
1/2
13.969 4.125
15.8 YES 65/370 216-259/330 84.0
MLP $
836.39
841.36
880.64
923.32
883.89
887.14
832.14
1019.86
1019.86
904.86
851.93
1204.04
1204.04
1204.04
922.50
1223.93
1171.86
1203.11
942.36
1074.96
1197.11
1229.00
919.89
907.96
1302.82
1260.61
1294.14
1072.29
1274.82
1274.82
1274.82
1039.46
1292.86
1292.86
1292.86
1049.04
* NOTE: When substituting compressors always check the capacitor MFD and voltage (when required) and replace if necessary. The capacitor MUST be the
proper MFD and voltage for the compressor.
5
Compressors
BRISTOL COMPRESSORS
HCRB Series
"Like for Like" Replacement for Copeland CR Series
SOURCE 1 PART NO.
S1-HCRB143ABCA
S1-HCRB183ABCA
S1-HCRB203ABCA
S1-HCRB223ABCA
S1-HCRB243ABCA
S1-HCRB283ABCA
S1-HCRB303ABCA
S1-HCRB323ABCA
S1-HCRB353ABCA
BRISTOL MODEL
NO.
HCRB143ABCA
HCRB183ABCA
HCRB203ABCA
HCRB223ABCA
HCRB243ABCA
HCRB283ABCA
HCRB303ABCA
HCRB323ABCA
HCRB353ABCA
CAPACITY BTHU
V-PH-HZ
RLA
LRA
EER
14100
18300
20500
22600
24200
28800
29900
30855
35700
230/208-1-60
230/208-1-60
230/208-1-60
230/208-1-60
230/208-1-60
230/208-1-60
230/208-1-60
230/208-1-60
230/208-1-60
5.8
7.4
8.6
9.4
9.6
12.1
12.1
13.1
15
48
48
60
60
61
73
82
82
86
10.4
10.7
10.7
10.7
10.9
10.9
11
10.9
10.9
SUCT ID (IN.) DISC ID (IN.)
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
MLP $
805.29
805.29
816.46
825.82
831.89
837.36
896.00
900.57
901.61
BRISTOL COMPRESSOR ACCESSORIES
Crankcase Heaters (CCH)
For Bristol Application
SOURCE 1 PART NO.
TYPE
S1-02515525702
S1-02517043700
S1-02519961701
S1-02531958000
S1-02531959000
S1-02531960000
S1-02532895000
S1-02533326000
S1-02533474240
S1-02533474480
S1-02541000000
WRAP AROUND
WRAP AROUND
WRAP AROUND
WRAP AROUND
WRAP AROUND
WRAP AROUND
INSERTION
INSERTION
WRAP AROUND
WRAP AROUND
WRAP AROUND
FIG. LENGTH OF VOLTS WATTS
ELEMENT
2
27 - 33
240
54
2
41 - 47
240
75
2
24 - 30
240
45
3
22 - 26
575
70
2
22 - 26
240
70
3
22 - 26
480
80
1
N/A
100 - 600
47*
1
N/A
100 - 600
30*
2
29 - 36
240
90
2
29 - 36
480
90
2
19 - 22
240
40
USED WITH COMPRESSOR
MLP $
MEASURE CIRCUMFERENCE OF COMPRESSOR
ALL H20 & H21 UP TO 5 TONS
ALL EXCEPT H20, H21 & H29
ALL EXCEPT H20 & H21
ALL H20 & H21 OVER 5 TONS
28.71
27.18
33.29
62.07
104.00
104.18
32.46
29.82
48.32
41.50
28.50
*If in doubt, use 47 watts
NOTE: For proper application of insertion type CCH, heat conductive com pound S1-01301502000 (available from SOURCE 1) or equivalent must be used.
6
Compressors
BRISTOL COMPRESSOR ACCESSORIES
Premier Compressor Blankets
For Noise Suppression
Features:
• Vinyl w/1/2 inch foam backing
• 1 inch wide velcro fasteners
• Die cut for proper fit
• UL recognized materials
SOURCE 1 PART NO.
FITS COMPRESSOR MODEL NO.
MLP $
S1-01004620000
S1-01004621000
S1-01004664000
S1-01005499000
S1-01005669000
S1-01005827000
S1-01006662000
H23 & H24B – ALL MODELS
H29B – ALL MODELS
H20, H21C & R – 4 TO 6-1/3 TONS
H20, H21C & R – UP TO 3-1/2 TONS
H23 & H24A 383 AND SMALLER
H23 & H24A 423 AND LARGER
H29A – ALL MODELS
70.11
72.89
69.89
65.61
74.64
73.82
193.82
SOURCE 1 PART NO.
MLP $
S1-01005977000
S1-01005979000
S1-01005980000
H23, H24, H25, 27A & 87A – ALL MODELS
H20 & H21C – ALL MODELS / H20 & H21R 483 AND SMALLER
H23, H24, H25 & H26B – ALL MODELS
82.11
75.89
73.79
Scott Mfg. “Acousticap” Compressor Blankets
Features:
• Superior noise reduction (NRC = 85)
• Molded closed cell foam shell w/acoustical liner
• Snap fasteners for ease of installation (some modification may be required)
High Torque Start Components
Note:
Compressor starting characteristics are definite. These high torque starting components are listed for Bristol compressors only. Do not attempt to cross
reference to other manufacturers.
Start Capacitor
SOURCE 1 PART NO.
COMPRESSOR MODEL NO.
MFD/VAC
MLP $
S1-02425071700
S1-02425071700
S1-02425071700
S1-02425071700
S1-02425071700
S1-02425071700
S1-02425071700
S1-02425071700
S1-02425075700
S1-02425075700
S1-02425191700
S1-02425191700
S1-02425191700
S1-02425191700
S1-02425191700
S1-02425191700
H24A423ABCA
H23A303ABCA
H23A323ABCA
H23A353ABHA
H23A423ABCA
H24A383ABCA
H23A383ABCA
H23A353ABCA
H23B18SABCA
H23B17SABCA
H23B243ABCA
H23B303ABCA
H23B19QABKA
H23B283ABHA
H23B28SABCA
H23B223ABHA
145-175/250
145-175/250
145-175/250
145-175/250
145-175/250
145-175/250
145-175/250
145-175/250
161-193/250
161-193/250
88-108/250
88-108/250
88-108/250
88-108/250
88-108/250
88-108/250
19.71
19.71
19.71
19.71
19.71
19.71
19.71
19.71
19.75
19.75
20.79
20.79
20.79
20.79
20.79
20.79
S1-02425191700
S1-02425191700
S1-02425191700
S1-02425191700
S1-02425191700
S1-02425191700
S1-02425191700
S1-02425191700
S1-02425191700
H23B263ABCA
H24B20QABKA
H23B26QABKA
H23B153ABHA
H24B26QABHA
H23B22SABCA
H23B35QABKA
H23B223ABCA
H23B173ABCA
88-108/330
88-108/250
88-108/250
88-108/250
88-108/250
88-108/250
88-108/250
88-108/330
88-108/330
20.79
20.79
20.79
20.79
20.79
20.79
20.79
20.79
20.79
*NOTE: When substituting compressors always check the capacitor M FD and voltage (when required) and
replace if necessary. T he capacitor M UST be the proper M FD and voltage for the com pressor.
7
Compressors
COPELAND A/C SCROLL MODELS
8
Compressors
COPELAND CRKQ, CIKQ MODELS
9
Compressors
COPELAND CR7, CR6, CRKF, CS, CF MODELS
10
Compressors
COPELAND RECIPROCATING COMPRESSORS
CR5 Series
For Air Conditioning & Heat Pump Application
Features:
• Internal line break motor protection
• Baked enamel finish
• Low vibration & noise
• Centrifugal oil pump
• High efficiency - 10.3 EER
• Refrigerant - HCFC-22
• Foot print - 7.5 x 7.5
• Quick connect wire connections
• Suitable for 50 Hz. operation
SUCTION
SOURCE 1 PART NO.
CAPACITY
BTUH
62,700
57,000
57,000
54500
56500
V-PH-HZ
RLA
LRA
EER
ID
S1-CRNQ-050EPFV970
S1-CRNQ-050ETF5970
S1-CRNQ-050ETFD970
S1-CRPQ-045EPFV970
S1-CRPQ-045ETF5970
COPELAND MODEL /
B/M NO.
CRNQ-050E-PFV970
CRNQ-050E-TF5-970
CRNQ-050E-TFD-970
CRPQ-045E-PFV-970
CRPQ-045E-TF5-970
208/230-1-60
200/230-3-60
460-3-60
208/230-1-60
200/230-3-60
34.3
19.2
8.7
27.6
17.6
142.0
130
65
135
105
10.3
9.8
9.8
10
9.8
7/8
7/8
7/8
7/8
7/8
HT (S) DISCH ID OVERALL HT
(IN)
(H) (IN)
16.0
1/2
16.5
15.29
1/2
16.13
15.29
1/2
16.13
15.04
1/2
16.13
15.04
1/2
16.13
S1-CRPQ-045ETFD970
CRPQ-045E-TFD-970
56500
460-3-60
9.4
55
10
7/8
15.04
1/2
16.13
CCH
YES
*RUN SHIP WT.
CAP
(LBS.)
55/440
88
90
82
87
82
91
MLP $
1848.11
2104.54
2104.54
1938.27
2055.82
2055.82
*NOTE: When substituting com pressors always check the capacitor M FD and voltage (when required) and replace if necessary T he capacitor M UST be the
proper M FD and voltage for the compressor.
11
Compressors
CR6 Series
Features:
• High efficiency - up to 11.0
SUCTION
SOURCE 1 PART NO.
CAPACITY
BTUH
16300
18000
19600
24500
28200
30000
32000
31900
29300
35000
34900
34900
38200
V-PH-HZ
RLA
LRA
EER
ID
HT (S)
S1-CR16K6E-PFV-875
S1-CR18K6E-PFV-875
S1-CR20K6E-PFV-875
S1-CR24K6E-PFV-875
S1-CR28K6E-PFV-875
S1-CR30K6E-PFV-875
S1-CR32K6E-PFV-875
S1-CR32K6E-TF5-875
S1-CR32K6E-TFD-875
S1-CR35K6E-PFV-875
S1-CR35K6E-TF5-875
S1-CR35K6E-TFD-875
S1-CR38K6E-PFV-875
COPELAND
MODEL/BOM NO.
CR16K6E-PFV-875
CR18K6E-PFV-875
CR20K6E-PFV-875
CR24K6E-PFV-875
CR28K6E-PFV-875
CR30K6E-PFV-875
CR32K6E-PFV-875
CR32K6E-TF5-875
CR32K6E-TFD-875
CR35K6E-PFV-875
CR35K6E-TF5-875
CR35K6E-TFD-875
CR38K6E-PFV-875
CCH
11.26
11.25
11.25
11.51
11.63
11.88
11.88
11.88
11.56
12.13
12.13
12.13
12.38
DISCH OVALL HT
ID
(H)
1/2 ID
10.228
0.38
13.19
0.38
13.19
1/2 ID
10.228
1/2 ID
10.228
1/2 ID
10.228
1/2 ID
10.228
1/2 ID
10.228
1/2 ID
13.81
1/2 ID
10.228
1/2 ID
10.228
1/2 ID
10.228
1/2 ID
10.228
208/230-1-60
208/230-1-60
208/230-1-60
208/230-1-60
208/230-1-60
208/230-1-60
208/230-1-60
208/230-1-60
460-3-60
208/230-1-60
230/200-3-60
460-3-60
208/230-1-60
9.6
10.4
10.6
12.4
15.3
16
16.1
10
4.6
18
11.4
4.8
19
49
49
50
61
75
82
82
72
33
96
75
41
105
10.6
10.6
10.7
10.9
10.8
10.9
10.8
11
10.5
10.9
11
11
10.9
3/4 ID
0.75
0.75
3/4 ID
3/4 ID
3/4 ID
3/4 ID
3/4 ID
3/4 ID
3/4 ID
3/4 ID
3/4 ID
3/4 ID
S1-CR38K6E-TF5-875
CR38K6E-TF5-875
37900
230/200-3-60
11.9
85
11
3/4 ID
12.38
1/2 ID
10.228
YES
N/A
67
1524.64
S1-CR38K6E-TFD-875
S1-CR38K6E-TFE-875
CR38K6E-TFD-875
CR38K6E-TFE-875
37900
3500
460-3-60
575-3-60
5.9
4.3
42
34
11
10.6
3/4 ID
3/4 ID
12.38
12.06
1/2 ID
1/2 ID
10.228
14.31
YES
N/A
67
67
1569.39
1603.00
S1-CR42K6E-PFV-875
S1-CR42K6E-TF5-875
S1-CR42K6E-TFD-875
CR42K6E-PFV-875
CR42K6E-TF5-875
CR42K6E-TFD-875
41900
41700
39500
208/230-1-60
230/200-3-60
460-3-60
20.4
14
5.7
102
91
42
10.9
10.9
11.1
3/4 ID
3/4 ID
3/4 ID
12.63
12.63
12.31
1/2 ID
1/2 ID
1/2 ID
10.228
10.228
14.56
YES
YES
N/A
74
69
69
1189.18
1593.82
1593.82
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
*RUN
CAP
SHIP WT.
(LBS.)
61
25 / 370
61
45 / 440
61
63
64
66
66
63
63
67
N/A
65
N/A
65
70
MLP $
994.29
1009.82
1021.68
1033.71
1048.61
1100.61
1155.18
1489.75
1489.75
1164.61
1492.18
1492.18
1172.04
12
Compressors
CRKQ Series
Features:
• Suitable for 50 Hz. Operation, High efficiency - up to 10.4
SUCTION
SOURCE 1 PART NO.
S1-CR18K6E-TF5-875
S1-CR18K6E-TFD-875
S1-CR24K6E-TF5-875
S1-CR24K6E-TFD-875
S1-CR28K6E-TF5-875
S1-CR28K6E-TFD-875
S1-CR47KQE-PFV-970
S1-CR47KQE-TF5-970
S1-CR47KQE-TFD-970
S1-CR53KQE-PFV-970
S1-CR53KQE-TF5-970
S1-CR53KQE-TFD-970
COPELAND MODEL / CAPACITY
B/M NO.
BTUH
CR18K6E-TF5-875
18400
CR18K6E-TFD-875
23300
CR24K6E-TF5-875
23300
CR24K6E-TFD-875
23200
CR28K6E-TF5-875
27300
CR28K6E-TFD-875
27500
CR47KQE-PFV-970
47500
CR47KQE-TF5-970
47,200
CR47KQE-TFD-970
47,200
CR53KQE-PFV-970
53,300
CR53KQE-TF5-970
53,200
CR53KQE-TFD-970
53,200
V-PH-HZ
RLA
LRA
EER
200/230-3-60
460-3-60
200/230-3-60
460-3-60
200/230-3-60
460-3-60
208/230-1-60
230/200-3-60
460-3-60
208/230-1-60
230/200-3-60
460-3-60
6.1
3.1
7.5
3.7
8.9
4.4
24.6
16
8.2
29
18
9.1
49
23
51
25
60.5
30
132
97
50
140
107
55
10.4
10.2
10.1
10.2
10.4
10.5
10.4
10.4
10.4
10.1
10.1
10.2
ID
HT (S)
DISCH
ID
0.63
11.375
0.38
0.63
11.375
0.38
0.63
11.375
0.38
0.63
11.875
0.38
0.63
11.375
0.38
0.63
11.375
0.38
0.88 14.11-14.49
0.5
7/8 ID
14.68
1/2 ID
7/8 ID
14.68
1/2 ID
7/8 ID
14.68
1/2 ID
7/8 ID
14.68
1/2 ID
7/8 ID
14.68
1/2 ID
OVALL
HT (H)
13.38
13.38
13.38
13.38
13.38
13.38
14.81
10.375
10.375
10.375
10.375
10.375
CCH *RUN CAP SHIP WT.
(LBS.)
YES
61
YES
61
YES
60
YES
60
YES
59
YES
59
YES
45 / 440
77
YES
N/A
77
YES
N/A
77
YES
77
YES
N/A
77
YES
N/A
77
MLP $
1193.54
1193.54
1300.75
1300.75
1322.64
1322.64
1285.25
1805.21
1834.43
1619.86
2160.36
2160.36
13
Compressors
COPELAND SCROLL COMPRESSORS
ZP Series for R410A
Features:
•
•
•
•
•
•
ZP Copeland Scroll compressors, for R410A, for comfort and process/precision cooling applications
Copeland Scroll axial and radial compliance for superior reliability and efficiency
Extended 5K operating envelope suitable for HP applications
Low TEWI (Total Equivalent-Warming Impact)
Low sounds and vibration level
Low oil circulation rate
SUCTION
SOURCE 1 PART NO. COPELAND MODEL CAPACITY
V-PH-HZ
/ B/M NO.
BTUH
S1-ZP154KCE-TW5950 ZP154KCE-TW5-950
155000
200/230-3-60
S1-ZP154KCE-TWD950 ZP154KCE-TWD-950
155000
460-3-60
S1-ZP180KCE-TWC961 ZP180KCE-TWC-961
180000
208/230-3-60
180000
460-3-60
183000
460-3-60
S1-ZP235KCE-TWC951 ZP235KCE-TWC-951
235000
208/230-3-60
235000
460-3-60
278000
460-3-60
294000
460-3-60
S1-ZP36K5E-PFV-830 ZP36K5E-PFV-830
360000
208/230-1-60
RLA
LRA
51.3
25.7
59.1
26.4
30
82.4
33.9
47.9
46.7
20
15.1
ID
300
150
425
187
173
505
225
250
272
112
1 3/8 S
1 3/8 S
2 1/4 RT
2 1/4 RT
1 3/8 S
1 5/8 S
1 5/8 S
2 1/8 S
1 5/8 S
7/8 S
88
10.3
7/8 S
11.61
S1-ZP36K5E-TF5-830
ZP36K5E-TF5-830
360000
200/230-3-60
S1-ZP36K5E-TFD-830
ZP36K5E-TFD-830
360000
208/230-1-60
6.6
44
10.3
7/8 S
385000
57000
460-3-60
208/230-1-60
60.7
33.6
310
158
11.1
10.1
1 5/8 S
7/8 S
S1-ZP57K3E-PFV-930 ZP57K3E-PFV-930
HT (S) DISCH HT OVALL HT COMP.
(D)
(H)
DIAM.
5.53
7/8 S
21.72
9.14
5.53
7/8 S
21.72
9.14
12.54 1 3/4 RT
23.3
11.14
12.54 1 3/4 RT
23.3
11.14
5.53
7/8 S
21.71
9.14
13.13
1 3/8 S
28.6
11.38
13.13
1 3/8 S
28.6
11.38
14.77
1 3/8 S
28.5
13.03
14.77
1 3/8 S
28.5
13.03
11.61
1/2 S
19.94
6.58
ARI
EER
11.1
11.1
11.2
11.2
11.2
11.1
11.1
11.2
11.1
10.2
1/2 S
19.94
11.61
1/2 S
14.77
11.73
1 3/8 S
1/2 S
*RUN CAP
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
6.58
N/A
19.94
6.58
N/A
28.5
17.91
13.03
7.3
N/A
S1-ZP57K3E-TF5-930
ZP57K3E-TF5-930
58000
200/230-3-60
22.9
155
10.6
7/8 S
11.73
1/2 S
17.91
7.3
N/A
S1-ZP57K3E-TFD-930
ZP57K3E-TFD-930
58000
460-3-60
10.7
75
10.6
7/8 S
11.73
1/2 S
17.91
7.3
N/A
S1-ZP61K5E-PFV-800
ZP61K5E-PFV-800
61500
208/230-1-60
34.3
178
10.5
7/8 S
11.61
1/2 S
17.36
6.58
S1-ZP61K5E-TFD-800
ZP61K5E-TFD-800
61500
460-3-60
9.1
66.1
10.7
7/8 S
11.61
1/2 S
17.5
6.58
N/A
S1-ZP61KCE-TF5-830
ZP61KCE-TF5-830
61500
200/230-3-60
21.2
123
10.8
7/8 S
11.73
1/2 S
17.91
7.3
N/A
S1-ZP67KCE-TF5-950
S1-ZP67KCE-TFD-950
S1-ZP72KCE-TF5-950
S1-ZP90KCE-TF5-950
S1-ZP90KCE-TFD-950
ZP67KCE-TF5-950
ZP67KCE-TFD-950
ZP72KCE-TF5-950
ZP90KCE-TF5-950
ZP90KCE-TFD-950
67500
67000
72000
90500
90500
200/230-3-60
460-3-60
200/230-3-60
200/230-3-60
460-3-60
25
11.8
25.9
32.9
16.4
149
75
164
195
95
10.8
10.8
10.7
10.8
10.8
7/8 S
7/8 S
7/8 S
1.125
1.125
11.73
11.73
11.73
3.69
3.69
1/2 S
1/2 S
1/2 S
7/8 S
7/8 S
17.91
17.91
17.91
18.75
18.75
7.3
7.3
7.3
9.14
9.14
N/A
N/A
N/A
N/A
N/A
14
WIRE SHIP WT.
CONN.
(LBS.)
Screw
146
Screw
143
Screw
235
Screw
235
Screw
146
Screw
310
Screw
310
Screw
391
Screw
353
Molded
71.2
Plug
Molded
63.7
Plug
Molded
64.3
Plug
Screw
390
Quick
98
Connect
Quick
92
Connect
Quick
92
Connect
Molded
77.2
Plug
Molded
77.2
Plug
Molded
88.8
Plug
Screw
88
Screw
88
Screw
88
Screw
127
Screw
127
MLP $
4596.29
4596.29
7472.79
5940.21
5555.04
10035.96
10035.96
11229.36
10341.50
1499.25
1745.57
1745.57
14829.57
2288.96
2470.50
2470.50
2377.68
2594.39
2468.43
2649.00
2649.00
2899.86
4209.39
4209.39
ZR16K thru ZR300K Series
Features:
• High efficiency & reliability
• Internal line break motor protection, Baked enamel finish
• High efficiency - up to 11.5 EER
• Foot print 7.5 x 7.5
• Wire connections:
– Q = Quick connect
– S = Screw
– P = Molded Plug
SOURCE 1 PART NO.
V-PH-HZ
B/M NO.
BTUH
ZR125KCE-TF5-950
125000
200/230-3-60
ZR125KCE-TFD-950
125000
460-3-60
RLA LRA
37.2
17.2
S1-01504334004
S1-01504342004
S1-01504479004
S1-ZR108KCE-TF5950
S1-ZR108KCE-TFE950
S1-ZR125KCE-TF7950
ZR144KCE-TFD-950
ZR108KCE-TFD-950
ZR160KCE-TWD-950
ZR108KCE-TF5-950
ZR108KCE-TFE-950
ZR125KCE-TF7-950
142000
106000
154000
106000
106000
125000
460-3-60
460-3-60
460-3-60
200/230-3-60
575-3-60
380-3-60
S1-ZR125KCE-TFE950
S1-ZR144KCE-TF5950
S1-ZR144KCE-TFE950
S1-ZR16K5E-PFV-800
S1-ZR18K5E-PFV-800
S1-ZR190KCE-TWD950
S1-ZR21K5E-PFV-800
S1-ZR21K5E-TF5-800
S1-ZR21K5E-TFD-800
S1-ZR25K5E-PFV-800
S1-ZR25K5E-TF5-800
S1-ZR25K5E-TFD-800
S1-ZR28K5E-PFV-800
S1-ZR28K5E-TF5-800
S1-ZR28K5E-TFD-800
S1-ZR300KCE-TWD965
S1-ZR32K5E-PFV-800
S1-ZR32K5E-TF5-800
S1-ZR32K5E-TFD-800
S1-ZR32K5E-TFE-800
S1-ZR38K5E-PFV-800
ZR125KCE-TFE-950
ZR144KCE-TF5-950
ZR144KCE-TFE-950
ZR16K5E-PFV-800
ZR18K5E-PFV-800
ZR190KCE-TWD-950
ZR21K5E-PFV-800
ZR21K5E-TF5-800
ZR21K5E-TFD-800
ZR25K5E-PFV-800
ZR25K5E-TF5-800
ZR25K5E-TFD-800
ZR28K5E-PFV-800
ZR28K5E-TF5-800
ZR28K5E-TFD-800
ZR300KCE-TWD-965
ZR32K5E-PFV-800
ZR32K5E-TF5-800
ZR32K5E-TFD-800
ZR32K5E-TFE-800
ZR38K5E-PFV-800
125000
142000
142000
15500
18000
181000
21000
21000
21000
25300
25300
25300
28400
28400
28400
293000
32600
32600
32600
32600
38000
S1-ZR38K5E-TF5-800
S1-ZR38K5E-TFD-800
S1-ZR38K5E-TFE-800
S1-ZR42K5E-PFV-800
S1-ZR42K5E-TF5-800
S1-ZR42K5E-TFD-800
S1-ZR42K5E-TFE-800
S1-ZR48K5E-PFV-800
S1-ZR48K5E-TF5-800
S1-ZR48K5E-TFD-800
ZR38K5E-TF5-800
ZR38K5E-TFD-800
ZR38K5E-TFE-800
ZR42K5E-PFV-800
ZR42K5E-TF5-800
ZR42K5E-TFD-800
ZR42K5E-TFE-800
ZR48K5E-PFV-800
ZR48K5E-TF5-800
ZR48K5E-TFD-800
S1-ZR48K5E-TFE-800
S1-01504475005
S1-ZR54K5E-TF5-800
S1-ZR54K5E-TFD-800
S1-ZR54K5E-TFE-800
S1-ZR57KCE-TF5-830
S1-ZR61KCE-PFV-930
S1-ZR61KCE-TF5-930
S1-ZR61KCE-TF5-950
S1-ZR61KCE-TFD-930
ZR48K5E-TFE-800
ZR54K5E-PFV-800
ZR54K5E-TF5-800
ZR54K5E-TFD-800
ZR54K5E-TFE-800
ZR57KCE-TF5-830
ZR61KCE-PFV-930
ZR61KCE-TF5-930
ZR61KCE-TF5-950
ZR61KCE-TFD-930
S1-01503482004
S1-01504203004
239
125
ARI
EER
11.6
11.6
HT (S) DISCH OVALL HT COMP.
HT (D)
(H)
DIAM.
1 3/8 4.81
19.73
21
9.14
1 3/8 4.81
19.73
21
9.14
18.6
15.5
23.1
30.1
12.1
21.2
125
114
150
225
80
145
11.6
11.5
11.2
11.5
11.5
11.6
1 3/8
1 3/8
1 3/8
1 3/8
1 3/8
1 3/8
4.81
4.81
5.33
4.81
4.81
4.81
19.73
19.73
20.45
19.73
19.73
19.73
21
21
21.72
21
21
21
9.14
9.14
9.14
9.14
9.14
9.14
135
132
143
132
131
135
5030.47
4198.05
4709.23
4273.96
4359.46
4579.32
575-3-60
200/230-3-60
575-3-60
208/230-1-60
208/230-1-60
460-3-60
208/230-1-60
230/200-3-60
460-3-60
208/230-1-60
230/200-3-60
460-3-60
208/230-1-60
230/200-3-60
460-3-60
460-3-60
208/230-1-60
230/200-3-60
460-3-60
575-3-60
208/230-1-60
12.4
42.3
14.2
9.3
10.7
28.2
12
8.6
4.3
15
8.9
4.6
15.7
11.1
5.7
43.6
17.1
12
6.4
4.6
21.4
80
245
100
40.3
55
173
56
58
29
68
58
29
75
73
38
250
87
73
38
28
112
11.6
11.6
11.6
10.6
10.6
10.9
10.7
10.7
10.7
10.9
10.9
10.9
11.0
11.0
11.0
11.4
11.2
11.4
11.4
11.4
11.2
1 3/8
1 3/8
1 3/8
3/4
3/4
1 3/8
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
2 1/8
3/4
3/4
3/4
3/4
7/8
4.81
4.81
4.81
10.1
10.1
5.33
10.1
10.1
10.1
10.1
10.1
10.1
10.1
10.1
10.1
14.77
10.1
10.1
10.1
10.1
11.1
19.73
19.73
19.73
14.2
14.2
20.45
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
25.97
14.2
14.2
14.2
14.2
15.4
21
21
21
16.1
16.1
21.72
16.1
15.1
15.1
16.1
16.1
16.1
16.1
16.1
16.1
28.5
16.1
16.1
16.1
16.1
17.2
9.14
9.14
9.14
5.5
5.5
9.14
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
13.03
5.5
5.5
5.5
5.5
6.5
4758.00
4897.96
4995.89
1090.54
1127.14
6413.07
1145.86
1577.18
1577.18
1193.82
1660.14
1660.14
1205.14
1644.32
1644.32
12173.07
1285.89
1667.86
1667.86
1694.89
1339.68
38000
38000
38000
42200
42200
42200
42200
48200
48200
48200
230/200-3-60
460-3-60
575-3-60
208/230-1-60
230/200-3-60
460-3-60
575-3-60
208/230-1-60
230/200-3-60
460-3-60
13.6
6.4
4.8
22.1
14.3
6.4
5.3
21.4
93
48
33
104
93
48
38
135
7.9
58
11.2
11.2
11.2
11.3
11.3
11.3
11.3
11.3
11.4
11.4
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
11.1
11.1
11.1
11.1
11.1
11.1
11.1
11.1
11.1
11.1
15.4
15.4
15.4
15.4
15.4
15.4
15.4
15.4
15.4
15.4
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
48200
53500
53500
53500
53500
57,200
62000
62000
61,000
62000
575-3-60
208/230-1-60
230/200-3-60
460-3-60
575-3-60
200/230-3-60
208/230-1-60
208/230-3-60
230/200-3-60
460-3-60
11.4
11.3
11.3
11.3
11.3
11.5
11.4
11.6
11.5
11.6
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
11.1
11.1
11.1
11.1
11.1
11.7
11.68
11.68
13.3
11.68
15.4
15.4
15.4
15.4
15.4
16.1
16.13
16.13
17.8
16.13
17.2
17.2
17.2
17.2
17.2
17.2
17.75
17.24
18.9
17.24
28.2 146
17.1 114
7.9
52
5.9 39.5
19.3 123.0
32.1 148
19.3 137
19.3 123.0
9.1
62
15
ID
*RUN WIRE SHIP WT.
CAP CONN. (LBS.)
135
135
MLP $
4621.27
4621.27
30/370
35/370
P
P
35/370
N/A
N/A
40/370
N/A
N/A
45/370
N/A
N/A
P
P
P
P
P
P
P
P
P
50/370
N/A
N/A
N/A
55/370
P
P
P
P
P
133
135
135
47
47
146
47
45
45
50
48
48
50
48
48
406
50
49
49
49
64
6.5
6.5
6.5
6.5
6.5
6.5
6.5
6.5
6.5
6.5
N/A
N/A
N/A
55/370
N/A
N/A
N/A
60/440
N/A
N/A
P
P
P
P
P
P
P
P
P
P
60
60
60
68
61
61
61
72
68
68
1738.54
1738.54
1765.61
1425.04
1773.71
1773.71
1800.82
1556.68
1839.07
1839.07
6.5
6.5
6.5
6.5
6.5
7.3
N/A
80/370
N/A
N/A
N/A
N/A
80 / 370
P
P
P
P
P
S
7.3
N/A
S
68
73
69
69
69
92
90
84
94
84
1949.50
1760.46
1998.07
1998.07
2048.36
2008.25
1936.54
2062.36
2043.96
2062.36
Compressors
COPELAND SCROLL COMPRESSORS
ZR16K thru ZR300K Series
SOURCE 1 PART NO.
S1-ZR61KCE-TFD-950
S1-ZR61KCE-TFE-930
S1-ZR68KCE-TF5-930
S1-ZR68KCE-TFD-930
S1-ZR68KCE-TFE-930
S1-ZR72KCE-TF5-950
S1-ZR72KCE-TFD-930
S1-ZR72KCE-TFD-950
S1-ZR72KCE-TFE-930
V-PH-HZ
B/M NO.
BTUH
ZR61KCE-TFD-950
61,000
460-3-60
ZR61KCE-TFE-930
58500
575-3-60
ZR68KCE-TF5-930
65500
200/230-3-60
ZR68KCE-TFD-930
65500
460-3-60
ZR68KCE-TFE-930
65500
575-3-60
ZR72KCE-TF5-950
72,100
230/200-3-60
ZR72KCE-TFD-930
72,100
460-3-60
ZR72KCE-TFD-950
73500
460-3-60
ZR72KCE-TFE-930
69500
575-3-60
RLA LRA
10.0 62.0
6.6
49
18.6 156
9
75
7.4
54
20.7 156.0
10.0 70.0
10
75
7.4
54
ARI
EER
11.5
11.1
10.9
10.9
10.9
11.5
11.5
11.7
11.2
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
ID
HT (S) DISCH OVALL HT COMP.
HT (D)
(H)
DIAM.
13.3
17.8
18.9
7.3
11.68 16.13
17.75
7.3
11.68 16.13
17.75
7.3
11.68 16.13
17.75
7.3
11.68 16.13
17.75
7.3
12.5
16.9
18.0
7.3
12.5
16.9
18.0
7.3
11.68 16.13
17.75
11.68 16.13
17.75
7.3
*RUN WIRE SHIP WT.
CAP CONN. (LBS.)
N/A
S
94
80
86
86
85
N/A
S
86
N/A
S
86
85
86
MLP $
2043.96
2081.07
2124.00
2130.93
2130.93
2163.50
2170.87
2163.50
N/A
S1-ZR81KCE-TF5-950
ZR81KCE-TF5-950
77000
200/230-3-60
22.4
164
10.8
7/8
11.68
16.13
17.95
7.3
86
2737.07
S1-ZR81KCE-TFE-930
ZR81KCE-TFE-950
77000
575-3-60
8.3
78
10.8
7/8
11.68
16.13
17.95
7.3
86
N/A
S1-ZR84KCE-TF5-950
ZR84KCE-TF5-950
81500
200/230-3-60
25.6
196
11.2
1 1/8
3.69
17.49
18.75
9.14
126
4085.18
S1-ZR84KCE-TFD-950
ZR84KCE-TFD-950
81500
460-3-60
12.8
100
11.2
1 1/8
3.69
17.49
18.75
9.14
126
4085.18
S1-ZR94KCE-TFE-950
ZR94KCE-TFE-950
94000
575-3-60
10.8
80
11.4
1 1/8
3.69
17.49
18.75
9.14
126
4284.96
*NOT E: When substituting com pressors always check the capacitor M FD and voltage (when required) and replace if necessary T he capacitor M UST be the
COPELAND COMPRESSOR ACCESSORIES
Capacity Control (Unloading) Valve With Gasket
SOURCE 1 PART NO.
DESCRIPTION
COMPRESSOR USED WITH
MLP $
S1-02208704000
VALVE,CAPACITY CONTROL UNLOADING SPORLAN
2D, 3D, 4R, 6R, 4D, 6D
372.33
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-02527939000
S1-057341
120 VOLT, EMERSON CLIMATE TECHNOLOGIES
24 VOLT, EMERSON CLIMATE TECHNOLOGIES
2D, 3D, 4R, 6R, 4D, 6D
2D, 3D, 4R, 6R, 4D, 6D
416.99
69.18
Coil, Solenoid (Unloading)
Control Module (Motor Protector) And Terminal Board
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-02533277000
S1-02535318000
MOTOR PROTECTOR CONTROL MODULE 24V
MOTOR PROTECTOR CONTROL MODULE 120/240V
2D, 3D, 4R, 6R, 4D, 6D
2D, 3D, 4R, 6R, 4D, 6D
576.48
614.49
16
Compressors
Crankcase Heaters (CCH)
For Copeland Application
SOURCE 1 PART NO.
TYPE
FIG.
LENGTH OF ELEMENT
VOLTS
WATTS
USED WITH COMPRESSOR
MLP $
S1-02515525702
S1-02517043700
S1-02519961701
S1-02527413000
S1-02528381700
S1-02531958000
S1-02531959000
S1-02531960000
S1-02532895000
S1-02533474240
S1-02533474480
S1-02541000000
WRAP AROUND
WRAP AROUND
WRAP AROUND
WRAP AROUND
INSERTION (D TYPE)
WRAP AROUND
WRAP AROUND
WRAP AROUND
INSERTION (ROUND)
WRAP AROUND
WRAP AROUND
WRAP AROUND
2
2
2
2
1
3
2
3
1
2
2
2
27 - 33
41 - 47
24 - 30
22 - 26
N/A
22 - 26
22 - 26
22 - 26
N/A
29 - 36
29 - 36
19 - 22
240
240
240
240
240 - 600
575
240
480
100 - 600
240
480
240
54
75
45
42
40
70
70
80
47
90
90
40
ALL CR
ALL CR
ALL RE
ALL WITH “D” SHAPED WELL
ZR UP TO 6-1/3 TONS
ZR UP TO 6-1/3 TONS
ZR UP TO 6-1/3 TONS
ALL WITH ROUND WELL
ZR94
ZR94
ZR94
28.71
27.18
33.29
38.68
58.68
62.07
104.00
104.18
32.46
48.32
41.50
28.50
NOTE: For proper appl ication of insertion type CCH heat conducti ve compound S1-01301502000 (avai labl e from SOURCE 1) or equivalent M UST be used.
Premier Mfg. Compressor Blankets
Features:
• Vinyl w/1/2 inch foam backing
• 1 inch wide velcro fasteners
• Die cut for proper fit
SOURCE 1 PART NO.
MLP $
S1-01004621000
CR38K6 & SMALLER
72.89
S1-01005499000
ZR UP TO 3-1/2 TONS
65.61
S1-01005669000-B
S1-01005827000
S1-01004580000
S1-01004664000
CRM & LARGER
BR, ZR94
CR42K6 & LARGER
ZR - 4 TO 6-1/3 TONS
74.64
73.82
85.36
69.89
SOURCE 1 PART NO.
MLP $
S1-01005977000
S1-01005979000
CRN & LARGER
CRK THRU CRM, ZR40 & SMALLER
82.11
75.89
S1-01005980000
CRH & SMALLER, RE
73.79
Scott Mfg. “Acousticap” Compressor Blankets
Features:
• Superior noise reduction (NRC = 85)
• Molded closed cell foam shell w/ acoustical liner
• Snap fasteners for ease of installation (some modification may be required)
Terminal Box, Parts And Accessories
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-02531493000
TERMINAL PARTS KIT
2D, 3D, 4R, 6R, 4D, 6D
553.76
17
Compressors
High Torque Start Components
Note:
Compressor Starting Characteristics Are Definite These High Torque Starting
Components Are Listed For Copeland Compressors Only.
Start Capacitor
SOURCE 1 PART NO.
COMPRESSOR MODEL NO.
*MFD/VAC
MLP $
S1-02425191700
S1-02425191700
S1-02425191700
S1-02425191700
S1-02425191700
S1-02425191700
S1-02425191700
S1-02425191700
S1-02425191700
S1-02425191700
S1-02425075700
S1-02425215700
S1-02425215700
S1-02425215700
S1-02425215700
S1-02425215700
S1-02425215700
S1-02425215700
S1-02425215700
S1-02425215700
S1-02425390700
S1-02425390700
S1-02425390700
S1-02425390700
S1-02425390700
S1-02425390700
ZR28K3-PFV
ZR40K3-PFV
ZR34K3-PFV
ZR36K3-PFV
ZR22K3-PFV
ZR42K3-PFV
CR28K6-PFV
CR32KF-PFV
ZR26K3-PFV
ZR30K3-PFV
CRG3-0250-PFV
CRM3-0400-PFV
CR35K6-PFV
CR38K6-PFV
CR42K6-PFV
CRP5-0450-PFV
CRL3-0350-PFV
CRK3-0325-PFV
CRJ3-0300-PFV
CRH3-0275-PFV
ZR57K3-PFV
ZR61Z3-PFV
ZR46K3-PFV
ZR47KC-PFV
ZR49K3-PFV
ZR54K3-PFV
88-108/330
88-108/330
88-108/330
88-108/330
88-108/330
88-108/330
88-108/330
88-108/330
88-108/330
88-108/330
161-193/250
189-227/330
189-227/330
189-227/330
189-227/330
189-227/330
189-227/330
189-227/330
189-227/330
189-227/330
270-324/330
270-324/330
270-324/330
270-324/330
270-324/330
270-324/330
20.79
20.79
20.79
20.79
20.79
20.79
20.79
20.79
20.79
20.79
19.75
28.82
28.82
28.82
28.82
28.82
28.82
28.82
28.82
28.82
35.64
35.64
35.64
35.64
35.64
35.64
Roto-Lock Adapters
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-998-0034-02
S1-998-0034-04
ADAPTER, 7/8 STUB TO 1.25-12 ROTALOCK
ADAPTER, 1-3/8 STUB TO 1.75-12 ROTALOCK
43.36
223.82
COMPRESSOR SOUND BLANKETS
Brinmar Sound Blankets
Brinmar Sound Blankets are a popular solution for reducing compressor noise, from air conditioners or heat pumps. The sound
blanket fits inside the cabinet and wraps around the compressor -- the noisiest component of an air conditioner or heat pump.
Brinmar's universal design accommodates hundreds of different styles and shapes of compressors. The two-piece design allows quick
installation in tight cabinets where space is a consideration and where the compressor is close to the coil or the fan. The sound
blanket is securely attached with hook and loop closures, which are durable and make installation quick and efficient.
Features:
• Minimum 5db (40%+) reduction of compressor noise
• Fits over 200 different compressor models, either recip or scroll
• Convenient, easy-to-install, universal-fit design
SOURCE 1 PART NO.
DESCRIPTION
LENGTH
WIDTH
HEIGHT
MLP $
S1-SBLHD
S1-SBRHD
BLANKET,COMPR,UNIV,12X12X19
12
10
12
10
19
15
98.32
82.18
S1-SBSHD
S1-SBUHD
8
10
8
10
15
19
72.54
84.57
18
Compressors
COMPRESSOR SOUND BLANKETS
SCOTT Acousticap® Compressor Blankets
Features:
• Superior noise reduction
• UL recognized
• Lightweight
• Easy installation
• Weatherability
• Cost-effective
ACOUSTICAL PERFORMANCE (SOUND ABSORPTION COEFFICIENTS)
FREQUENCY (HZ) ABSORPTION AT 1/3 OCTAVE FREQUENCY
ACOUSTICAP ®
125
.19
250
.49
500
.88
1000
1.02
2000
1.02
4000
1.03
NRC *
.85
* Noise Reduction Coefficient
Testing was in accordance with ASTM C-423 and performed by an outside laboratory accredited by the Department of Commerce.
ACOUSTICAL PERFORMANCE (SOUND TRANSMISSION LOSS)
FREQUENCY HERTZ
SOURCE DB
RECEIVE DB
TL DB
STC CONTOUR
125
91.7
78.1
2.2
-5
250
91.4
79.6
2.7
4
500
93.3
79.6
5.8
11
1000
97.6
79.3
10.8
14
2000
97.3
69.8
17.6
15
4000
97.4
61.0
24.4
15
Sound Transmission Class (STC) = 11
Testing was in accordance with ASTM E-90 and performed by an outside laboratory accredited by the Department of
Commerce.
SOURCE 1 PART NO.
SCOTT MFG. MODEL NO.
DIAMETER
HEIGHT
FOR USED WITH COMPRESSOR
MLP $
S1-01005977000
SC9301A
9-1/2 - 11
15 - 17
82.11
S1-01005979000
SC9520A
7 - 8-1/2
15 - 17
S1-01005980000
SC9521A
7 - 8-1/2
12 - 15
H23A, H24A, H25A, H26A, H27A, H87A ALL MODELS CRN AND LARGER
H20 AND H21C - ALL MODELS, H20 AND
21R - 483 AND SMALLER CRK - CRM,
ZR40 AND SMALLER
H23B, H24B, H25B, H26B - ALL MODELS
CRH AND SMALLER, RE ALL AW AND AV
19
75.89
73.79
AccuTrak Ultrasonic Leak Detector
Superior Signal - Model VPE - Now w ith Touchprobe Included!
Patented Technology Detects the Ultrasonic SOUND of a Leak!
AccuTrak offers high sensitivity & great sound quality in a compact package designed for one hand operation. Instrument, flexible
waveguide, headset, touchprobe and battery included in a hardshell case.
The important features of the AccuTrak model VPE is that it is low cost and highly sensitive, small and simple to use, runs on a 9 volt
battery, patented technology, classic heterodyne detector, designed for use in areas of low to moderate background noise.
•
•
•
•
•
•
•
Most sensitive ultrasonic detector available to the trade
Exact translation of leak sounds, (NO Beeps or Squeals)
NOT affected by wind or fans
Detects ANY pressurized gas
Detects vacuum leaks
No false alarms from residues or other stray gasses
No sensors to clean or replace
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-NC-61307
AccuTrak Ultrasonic Leak Detector
1146.00
CPS PRODUCTS REFRIGERANT CHARGING EQUIPMENT
CPS Products Leak Detectors
CPS Products proudly introduces the all new Leak-Seeker featuring E_MOS technology. Packed with unique design features the new
Leak-Seeker from CPS is the best leak detector you can find, anywhere in the world at any price, truly an Innovation in Design™.
Features:
• Microprocessor controlled sensor electronics utilizing a multi channel signal detection method, improves sensitivity while reducing
false alarm
• Software managed sensor rejuvenation mode, automatically initiated at each start up ensures the highest level of sensitivity every
use, for up to 500 hours of detecting leaks of less than .1 oz per year
• Sensitivity remains constant over the life of the sensor
• Sensitivity to 35 parts per million (less than .01 oz per year)
• Senses all refrigerants including those with hydrocarbon components
• 500 hours sensor life
• 50 hour battery life (3 C batteries)
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CP-LS1
S1-CP-LS2
S1-CP-EMOS2
LEAK DETECTOR,REFRIGERANT,LEAK-SEEKER I
LEAK DETECTOR,REFRIGERANT,LEAK-SEEKER II
SENSOR,REPLACEMENT,LEAK-SEEKER I AND II
435.11
662.14
79.14
CPS Products Charging Hoses
SOURCE 1 PART NO.
DESCRIPTION
COLOR
LENGTH (IN INCHES)
MLP $
S1-CP-HP5
HOSE,CHARGING SET PREMIUM 5',3 PK
COLOR-CODED SET
60
116.75
S1-CP-HP5A
S1-CP-HP5B
S1-CP-HP5E
S1-CP-HP5L
S1-CP-HP5R
S1-CP-HP5Y
HOSE,CHARGING SET PREMIUM 5' ABB,3 PK
HOSE,CHARGING SET PREMIUM 5'
HOSE,CHARGING SET PREMIUM 5' BV,3 PK
HOSE,CHARGING SET PREMIUM 5' INL BV,3 PK
COLOR-CODED SET
BLUE
COLOR-CODED SET
COLOR-CODED SET
RED
YELLOW
60
60
60
60
60
60
172.61
38.89
183.71
194.93
38.89
38.89
20
CPS Products Charging Hoses Accessories
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CP-AB
S1-CP-AB90
S1-CP-HTE
S1-CP-HXG
HOSE END FTG,1/4" SAE M X 1/4" SAE F,ABB
HOSE END FTG,1/4" SAE M X 1/4" SAE F,90
HOSE,CHARGING,6" BV EXT,1/4" SAE,3 PK
HOSE GASKET,1/4" SAE REPLACE B426,10 PK
26.93
28.46
99.29
4.93
JB INDUSTRIES INC. REFRIGERANT CHARGING EQUIPMENT
JB CL Series Charging Hoses
Features:
• Blowout resistant depressor and barrel gasket
• Depressor set to ARI Standard for access valve core
• Slotted Coupler prevents back spray
SOURCE 1 PART NO.
DESCRIPTION
COLOR
LENGTH (IN INCHES)
MLP $
S1-CCL-36
S1-CCL-48
S1-CCL-60
S1-CCL-72
S1-CL-36B
S1-CL-36R
S1-CL-36Y
S1-CL-48B
S1-CL-48R
S1-CL-48Y
S1-CL-60B
S1-CL-60R
S1-CL-60Y
S1-CL-72B
S1-CL-72R
S1-CL-72Y
CL SERIES CHARGING HOSES
CL SERIES CHARGING HOSE
COLOR-CODED SETS
COLOR-CODED SETS
COLOR-CODED SETS
COLOR-CODED SETS
BLUE
RED
YELLOW
BLUE
RED
YELLOW
BLUE
RED
YELLOW
BLUE
RED
YELLOW
36
48
60
72
36"
36"
36"
48"
48"
48"
60"
60"
60"
72"
72"
72"
90.29
106.82
123.29
145.43
31.57
31.57
31.57
37.36
37.36
37.36
43.14
43.14
43.14
48.93
48.93
48.93
Replacement Parts for CL Series Charging Hoses
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-P509
S1-P90513
1/4” GASKET
DEPRESSOR
7.54
8.21
21
JB Enviro-Safe CLE Series Charging Hoses with Gasket Seal Fitting
Features:
• Blowout resistant depressor and barrel gasket
SOURCE 1 PART NO.
DESCRIPTION
COLOR
LENGTH (IN INCHES)
MLP $
S1-CCLE-36
S1-CCLE-48
S1-CCLE-60
S1-CCLE-72
S1-CLE-36B
S1-CLE-36R
S1-CLE-36Y
S1-CLE-48B
S1-CLE-48R
S1-CLE-48Y
S1-CLE-60B
S1-CLE-60R
S1-CLE-60Y
S1-CLE-72B
S1-CLE-72R
S1-CLE-72Y
CLE SERIES CHARGING HOSES
CLE CHARGING HOSE
CLE CHARGING HOSE
CLE CHARGING HOSE
CLE CHARGING HOSE
CLE CHARGING HOSE
CLE CHARGING HOSE
CLE CHARGING HOSE
CLE CHARGING HOSE
CLE CHARGING HOSE
CLE CHARGING HOSE
CLE CHARGING HOSE
CLE CHARGING HOSE
COLOR-CODED SET
COLOR-CODED SET
COLOR-CODED SET
COLOR-CODED SET
BLUE
RED
YELLOW
BLUE
RED
YELLOW
BLUE
RED
YELLOW
BLUE
RED
YELLOW
36
48
60
72
36
36
36
48
48
48
60
60
60
72
72
72
110.46
129.00
153.32
168.46
38.71
38.71
38.71
45.21
45.21
45.21
51.68
51.68
51.68
58.18
58.14
58.14
Replacement Parts for CLE Series Charging Hoses
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-P509
S1-P90513
1/4” GASKET
DEPRESSOR
7.54
8.21
JB Enviro-Safe CLS Series Charging Hoses with Secure-Seal Fitting
Features:
• Opens to Full Flow
• Automatically traps refrigerant discharge in hose
SOURCE 1 PART NO.
DESCRIPTION
COLOR
LENGTH (IN INCHES)
MLP $
S1-CCLS-36
S1-CCLS-48
S1-CCLS-60
S1-CCLS-72
S1-CLS-36B
S1-CLS-36R
S1-CLS-36Y
S1-CLS-48B
S1-CLS-48R
S1-CLS-48Y
S1-CLS-60B
S1-CLS-60R
S1-CLS-60Y
S1-CLS-72B
S1-CLS-72R
S1-CLS-72Y
CLS SERIES CHARGING HOSES
CLS CHARGING HOSE
CLS CHARGING HOSE
CLS CHARGING HOSE
CLS CHARGING HOSE
CLS CHARGING HOSE
CLS CHARGING HOSE
CLS CHARGING HOSE
CLS CHARGING HOSE
CLS CHARGING HOSE
CLS CHARGING HOSE
CLS CHARGING HOSE
CLS CHARGING HOSE
COLOR-CODED SET
COLOR-CODED SET
COLOR-CODED SET
COLOR-CODED SET
BLUE
RED
YELLOW
BLUE
RED
YELLOW
BLUE
RED
YELLOW
BLUE
RED
YELLOW
36
48
60
72
36
36
36
48
48
48
60
60
60
72
72
72
168.93
190.43
220.43
242.79
61.50
59.14
59.14
69.36
69.36
69.36
77.25
77.25
77.25
81.86
85.14
81.86
Replacement Parts for CLS Series Charging Hoses
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-P90022
REPLACEMENT O-RING
11.11
22
JB Enviro-Safe CLV Series Charging Hoses with Secure-Seal Fitting
Features:
• Blowout Resistant Depressor and Barrel Gasket
• Quarter turn On/Off
• UL approved Shut-Off ball valve
SOURCE 1 PART NO.
DESCRIPTION
COLOR
LENGTH (IN INCHES)
MLP $
S1-CCLV-36
S1-CCLV-48
S1-CCLV-60
S1-CCLV-72
S1-CLV-36B
S1-CLV-36R
S1-CLV-36Y
S1-CLV-48B
S1-CLV-48R
S1-CLV-48Y
S1-CLV-60B
S1-CLV-60R
S1-CLV-60Y
S1-CLV-72B
S1-CLV-72R
S1-CLV-72Y
CLV SERIES CHARGING HOSES
CLV CHARGING HOSE
CLV CHARGING HOSE
CLV CHARGING HOSE
CLV CHARGING HOSE
CLV CHARGING HOSE
CLV CHARGING HOSE
CLV CHARGING HOSE
CLV CHARGING HOSE
CLV CHARGING HOSE
CLV CHARGING HOSE
CLV CHARGING HOSE
CLV CHARGING HOSE
COLORCODED SET
COLORCODED SET
COLORCODED SET
COLORCODED SET
BLUE
RED
YELLOW
BLUE
RED
YELLOW
BLUE
RED
YELLOW
BLUE
RED
YELLOW
36*
48*
60*
72*
36*
36*
36*
48*
48*
48*
60*
60*
60*
72*
72*
72*
251.71
273.64
307.39
330.14
88.18
88.18
88.18
53.57
96.04
96.04
103.89
103.89
108.07
111.75
111.75
111.75
* Hoses com e with 6” Whip End
Replacement Parts for CLV Series Charging Hoses
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-P90022
REPLACEMENT O-RING
11.11
CPS Products Charging Manifolds
The CPS Products manifolds feature the Piston series 2 valve anodized aluminum block body with ¼" SAE 45° fittings, Triple Seal™
piston valves, easy-to-read accuracy gauges, extra access port in center with Schrader® valve and hanging hook. MADE IN USA
Features:
•
•
•
•
•
•
2 valve anodized aluminum body with ¼" SAE fittings
Triple Seal™ piston valves
Accuracy gauges with internal silicon dampening cup for Flutter-Free operation
Pressure Scales: PSI
Temperature Scales: °F
Premium 5ft Pro-Set® hose set with ¼" SAE fittings
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CP-MBCP5
S1-CP-MBHP5
S1-CP-MT2H7P5
MANIFOLD,CHG R-12/22/502,5' HOSES
MANIFOLD,CHG R-22/404A/410A,5' HOSES
MANIFOLD,CHG R-22/404A/410A,2V ALUM,5' H
171.07
171.07
257.93
23
JB R22 & R410a Charging Manifolds
Forged Bar R410a Manifolds
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-23500
S1-23506
S1-23513
S1-24225
S1-25225
NO HOSE SET
ENVIRO-SAFE HOSE SETS 5’ (60”)
ENVIRO-SAFE HOSE SETS WITH BALL VALVE SHUT-OFF 5’ (60”)
2-VALVE ALUMINUM MANIFOLD W/O HOSES, 80MM ILUMINATING GAUGES
4-VALVE ALUMINUM MANIFOLD W/60” CCLE HOSES, 80MM ILLUMINATING GAUGES
150.07
286.82
412.61
233.68
352.96
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-M2-12
S1-M2-22225
S1-M2-36
S1-M2-5
S1-M2-5-410A
S1-M2-6
S1-M2-8
S1-M2-8-410A
STANDARD MANIFOLD BODY ONLY
STANDARD MANIFOLD W/O HOSES, 80MM GAUGES
WITH 36” STANDARD HOSE SET
WITH 60” STANDARD HOSE SET
STANDARD MANIFOLD W/60” CCL HOSE SET, R410a
3’ (36”) RED & BLUE AND 5’ (60”) YELLOW
STANDARD R22 MANIFOLD ONLY (W/O HOSES)
STANDARD MANIFOLD W/O HOSES, R410a
85.39
174.50
213.07
259.18
271.32
209.96
133.96
140.04
Standard Manifolds
CPS Products Charging Manifold Gauges
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CP-MXPV
S1-CP-RGCH
S1-CP-RGCL
S1-CP-RGH7H
S1-CP-RGH7L
S1-CP-VG200
VLV,COMPLETE ASSEMBLY,TRIPLE-SEAL
GAUGE,REPLACE,HI R-12/22/502 68MM PSI/F
GAUGE,REPLACE,LO R-12/22/502 68MM PSI/F
GAUGE,HI SIDE,R-134a/22/404A/410A, PSI/F
GAUGE,LO SIDE,R-134a/22/404A/410A, PSI/F
GAUGE,VACUUM,DIGITAL LCD DISPLAY
15.79
32.36
32.36
47.46
47.46
416.67
R22 & R410a Charging Manifold Gauges
Compound Gauges (°F)
Specifications:
Compound Gauges: 30” Vacuum to 120 PSI, Retard to 350 PSI (R410a gauges 250/500 PSI)
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-M2-250
S1-M2-250LF
S1-M2-410
S1-M2-410LF
S1-M2-415LF
S1-M2-460
S1-M2-820
BLUE PLASTIC CASE
LIQUID FILLED METAL COMPOUND GAUGE-BLUE (M5)
R410A COMPOUND GAUGE
LIQUID FILLED 410A COMPOUND GAUGE-BLUE
LIQUID FILLED R410A PRESSURE GAUGE-RED
2-1/2 BLUE COMPOUND GAUGE
80MM ILLUMINATING BLUE COMPOUND GAUGE
38.46
57.93
37.50
57.07
54.32
38.46
64.25
Pressure Gauges
Specifications:
Pressure Gauges: 0 to 500 PSI (R410a gauges 0 to 800 PSI)
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-M2-415
S1-M2-465
S1-M2-500
S1-M2-825
R410A PRESSURE GAUGE
2-1/2 RED PRESSURE GAUGE
RED PLASTIC CASE
80MM ILLUMINATING RED PRESSURE GAUGE
37.50
37.50
38.46
64.32
24
SH-35N Superheat Subcooling Gauge
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-SH-35N
SUPERHEAT/SUBCOOLING GAUGE WITH MEMORY (F) IN CASE
723.82
CPS Products Refrigerant Recovery Machine
Fastest, Smallest, Lightest, Best looking and Most reliable heavy duty recovery machine in the world. Revolutionary "vacuum pump"
style design. Designed and Manufactured in the USA.
Features:
•
•
•
•
•
•
•
•
•
Compressor Type: 2 Cylinder Oil-less Reciprocating Compressor
Dimensions: 15cm (6") Wide x 30cm (12") Long x 23cm (9") High
Weight: 24.5 lb
Operating Temperature Range: 0?C (32?F) to 49?C (120?F)
Power Source: 115 V 50/60 Hz
Filtration: Cleanable 100 - mesh screen integrated into Suction Port
Ov erload Protection: Motor Thermally Protected
High Pressure Shut-Off: 550 psig
Refrigerants: R-12, R-134a, R-401C, R-406A, R-500, R-401A, R-409A, R-401B, R-412A, R-411A, R-407D, R-22, R-411B, R-502,
R-407C, R-402B, R408A, R-509, R-407A, R-404A, R-402A, R-507, R-407B, R-410A
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CP-TR21
MACHINE,REFR RECOVERY,TWIN CYL,PRO-SET
1919.25
CPS Products Refrigerant Recovery
The effects of high ambient temperatures and elevated tank pressure s on the recovery process are well known. As the temperature /
pressure of the recovery cylinder increases, the speed of the recovery process decreases until it is finally halted by a high pressure
shut down. The Pro-Set® MT69 Molecular Transformator provides valuable assistance in the transformation of high temperature /
pressure vapor refrigerant into low temperature / pressure liquid refrigerant, dramatically improving recovery speed and efficiency.
The Molecular Transformator is a patent pending "Innovation in Design™" from CPS, intended for use with all commercially available
brands of refrigerant recovery equipment. It is extremely easy to use, saves time and money and provides the missing link in high
ambient performance that exists in all commercially available recovery machines on the market today.
Features:
•
•
•
•
•
•
•
Dimensions: 4" D x 12" H
Weight: 5 lbs
Heat Sink Temperature: 100° F
Maximum Operation Pressure: 500 PSIG
Discharge Pressure Gauge: 0 to 600 PSIG
Inlet / Outlet: 1/4" SAE Male
Made in USA
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CP-MT69
TRANSFORMATOR,REFR RECOVERY,HI AMBIENT TMP
352.50
25
Micron Gauge Hookup Kit
Used in conjunction with JB digital micron gauges DV-40 or DV-22N, the DV-29 kit ensures a leak-proof setup by creating a closed
sy stem, eliminating any leakage under deep vacuum.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-DV-29
KIT, HOOKUP, MICRON AND SUPERHEAT GAUGE
324.61
CPS Products Vacuum Pumps
The VP6D Pro-Set® Premium Series vacuum pump is a 6 CFM, 2 stage unit with a versatile dual voltage 1 / 2 HP motor. The unit
boasts the same high quality; high value features engineered into all of our Pro-Set® vacuum pumps providing performance
excellence and years of reliable service.
The VP8D Pro-Set® Premium Series vacuum pump is a 8 CFM, 2 stage unit with a versatile dual voltage 2 / 3 HP motor. The unit
boasts the same high quality; high value features engineered into all of our Pro-Set® vacuum pumps providing performance
excellence and years of reliable service.
Features:
•
•
•
•
•
•
•
•
•
Dual voltage operation 110-120V / 220V 50 / 60Hz
Exceptional ultimate vacuum rating as low as 10 microns
Advanced air cooled motor design for operation in high ambient temperatures
Proprietary oil mist free exhaust port cap for clean, safe job environment
Gas ballast valve speeds achievement of deep vacuum
Multiple port connections for 1 / 4", 3 / 8" and 1 / 2" ACME
Easy maintenance with large oil sight glass and fill port with easily accessible oil drain port
Solid rubber base provides extreme shock resistance
Sure grip handle ergonomically designed for superior comfort and portability
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CP-VP6D
S1-CP-VP8D
S1-CP-VPXJ220
PUMP,VACUUM,6 CFM,2 STAGE,DV,115/230V
PUMP,VACUUM,8 CFM,2 STAGE,DV,115/230V
JUMPER CORD KIT,VACUUM PUMP,IEC-ALG CLIP
775.29
1019.43
102.78
JB Eliminator Vacuum Pump
Features:
• 3CFM with 1/2 HP motor
• 25 micron field tested (thermistor gauge reading)
• Wide stance feet for stability
• 2-stage direct drive design, O-ring seal drain valve
• Check valve prevents oil backflow during power failure
• Low-profile rocker switch helps prevent damage and accidental shut off
• 16-ounce oil capacity for good contaminant absorption and easy oil changes Completely field repairable
SOURCE 1 PART NO.
DESCRIPTION
FREE AIR DISPLACEMENT
SPECIFICATIONS
MLP $
S1-DV-4E
ELIMINATOR VACUUM PUMP
4 CFM
1/2 HP, 115 V, 60 HZ, 1725 RPM
843.79
S1-DV-6E
ELIMINATOR VACUUM PUMP
6 CFM
1/2 HP, 115 V, 60 HZ, 1725 RPM
971.14
26
JB Platinum Series Vacuum Pumps
Features:
• 2 stage Direct Drive
• 25 micron field tested (Thermistor Gauge reading)
• Check Valve prevents oil backflow during power failure
• Low profile rocker switch
• Completely field repairable
• One micron on a U-tube manometer; 25,400 microns = “1”
Shipping Container Dimensions = 14-7/8”H x 9-5/16”W x 16-1/2”L
SOURCE 1 PART NO.
DESCRIPTION
S1-DV-142N
S1-DV-200N
S1-DV-85N
1/2 HP, 115 V, 60 HZ, 1725 RPM
1/2 HP, 115 V, 60 HZ, 1725 RPM
1/2 HP, 115 V, 60 HZ, 1725 RPM
FREE AIR DISPLACEMENT
(L/MIN.)
5 CFM (142)
7 CFM (200)
3 CFM (85)
INTAKE PORTS (MALE
FLARE)
3/8” X 1/4” X 3/8”
3/8” X 1/4” X 3/8”
1/4” X 3/8”
OIL CAPACITY
SHIP WEIGHT
MLP $
23 OZ. (660 CC)
23 OZ. (660 CC)
27 OZ. (785 CC)
32 LBS.
30 LBS.
30 LBS.
1358.96
1558.64
1216.82
JB Digital Vacuum Gauges
JB’s Digital Vacuum Gauge reads vacuum in 7 international units: Microns, PSIA, In Hg, mBars, Pascals, Torr, and mTorr. The DV- N
has a micron range of 0 to 9,000 Microns. It is a good idea to attach the micron gauge to the vacuum pump before evacuation to make
sure the pump pulls down to at least 50 microns. If it doesn't, your pump is contaminated and the oil should be changed A compound
gauge only indicates that a vacuum is being produced, but does not tell you if moisture or acids are still in the system The DV- N,
however, is the only tool to accurately read the low pressure produced when evacuation/ dehydration is complete.
Note: The DV-22N is not recommended for connection to vacuum pump when blanking off isolation valve.
Features:
• Simple two button operation for convenience
• Sealed touch buttons protect unit against dust and spills
• Low battery indicator lets you know when to replace the 9 volt battery (not included)
• Powers off after 10 minutes to save battery life
• Retractable hanging hook so the DV- N can hang or lie flat
• NIST Traceable
• Leak-proof with O-ring coupler to ensure proper register of vacuum in system
• Digital display with solid state circuitry so there is no adjustment necessary for fluctuating temperatures.
• Saves last vacuum readout after shut down for added convenience
Specifications:
Effectiv e Range: 20–9,000 microns
Ambient Temperature: +32°F to +120°F (0°C to 48.9°C)
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-DV-24N
DV-22N WITH PROTECTIVE CARRYING CASE
586.93
27
CPS Products Refrigerant Scale
With accuracy specifications exceeding all OEM requirements for charging accuracy, that is twice as good as any competitive unit on
the market, the Standard Series of Compute-A- Charge® scales are Performance Leaders in accuracy and reliability and the Standard
by which all others are measured. The competition simply doesn't measure up!
Features:
• Calibrated to strict NIST Standards at the CPS manufacturing facility in Hialeah, Fl.
• Accuracy specification exceeds all OEM requirements for charging accuracy and is twice as good as any competitive unit on the
market.
• Temperature compensated over the entire operating temperature range to maintain charging accuracy under all ambient conditions.
• Selectable measurements in Imperial or Metric units.
• Environmentally sealed strain gage beam load cell technology first introduced by CPS in 1985.
• Designed to withstand overloads of 150%.
• High contrast wide angle LCD Display for ease of viewing.
• Platform can be removed from carrying case.
• Magnetic back on handheld unit.
• Hanging hook.
• Powered by two (9V) batteries providing 60 hours of continuous usage.
• User selectable automatic power off to conserve batteries.
• Designed and Manufactured in the USA.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CP-CC220
SCALE,REFRIGERANT CHG,220 LB,HI-RES ELEC
496.04
Refrigerant Scale
The award-winning Atlas refrigerant charging scale is designed for the HVAC/R industry. Everyday users will appreciate the
advanced solid state load cell for superior sensitivity (0.25 oz/10g) and accuracy. 220-lb (100 kg) capacity. All metal construction.
Heavy duty carrying case. Easy-to-read display.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-DS20000
SCALE, REFRIGERANT CHARGING, 220 LB, ATLAS
609.71
HVAC Calculator
WinLine HVAC Pocket Calculator
Features:
• Converts pressure to temperature and temperature to pressure for refrigerant gases; 11,12, 22, 500, 502 and 717
• Clocks BTU/HR input of natural gas through a gas meter
• Determines % of relative humidity by entering dry and wet bulb temperature
• Converts °F to °C and °C to °F
• Full four function calculator
• Use s two CR2016 lithium batteries
SOURCE 1 PART NO.
DESCRIPTION
MFG NO.
MLP $
S1-52635014000
HVAC POCKET CALCULATOR
100
112.00
28
REFRIGERANT RECOVERY PRODUCTS
Refrigerant Recovery Cylinders
DOT Classified for recovery, recycling, service and reclaim. Liquid and vapor valves (“Y” valve or separate valve configurations) are
installed in all cylinders. Painted yellow/gray per ARI guidelines. Float switches have 3-pin Bra Harrison connectors.
Caution: Never overfill cylinders. Maximum refrigerant capacity is limited to 80% of the water capacity of the cylinder in lbs. (see table
below). DOT requires cylinders to be retested every five years. Some recovery equipment uses weight scales to cut off refrigerant fill
at 80% of capacity. Be sure cylinder tare weight is correct for this type of equipment.
DOT Classification Example: 4BA400: 400 psi working pressure; 800 psi test pressure (double the working pressure); 1,600 psi
minimum burst pressure (double the test pressure). Pressure relief/safety valve is set to release at between 75-100% of the test
pressure. For example, in the 4BA400 tanks which have a 800 psi test pressure, the relief valve opens at between 600 psi and 800
psi.
SOURCE 1 PART NO.
DESCRIPTION
DOT CLASS
3/4” NPT PLUG
FLOAT SWITCH
WATER CAP.
TARE WT.
MLP $
S1-02033
S1-02035
S1-02053
S1-02055
S1-02100
S1-02255
30 LB.
30 LB.
50 LB.
50 LB.
100 LB.
250 LB.
4BA400
4BA400
4BA400
4BA400
4BW400
4BW260
YES
NO
YES
NO
NO
YES
NO
YES
NO
YES
NO
NO
26.2 LBS.
26.2 LBS.
47.7 LBS.
47.7 LBS.
123 LBS.
239 LBS.
17 LBS.
17 LBS.
28 LBS.
28 LBS.
48 LBS.
85 LBS.
338.89
554.93
367.21
589.50
917.21
1200.96
REFRIGERANT CHARGING PRODUCTS
Cushion Clamps
An industry standard universal clamp that mounts to standard strut. Steel with electro-dichromate finish to resist corrosion. T he lock
nut has a nylon insert for a positive lock. The polymeric grommet withstands temperatures from -25°C to 125°C and resists the effects
of most oils, chemicals, and industrial cleaning compounds.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-538-1/2
S1-538-1/4
S1-538-1-1/8
S1-538-1-3/8
S1-538-1-5/8
S1-538-2-1/8
S1-538-2-5/8
S1-538-2-5/8-JP
S1-538-3/4
S1-538-3/8
S1-538-3-1/8
S1-538-3-1/8-JP
S1-538-3-5/8
S1-538-3-5/8-JP
S1-538-4-1/8
S1-538-4-1/8-JP
S1-538-5/8
S1-538-7/8
CUSHION CLAMP – 1/2”
CUSHION CLAMP – 1-1/8”
CUSHION CLAMP - 2-5/8"
25/BOX
25/BOX
10/BOX
10/BOX
10/BOX
10/BOX
10/BOX
5/BOX
25/BOX
25/BOX
10/BOX
5/BOX
10/BOX
5/BOX
10/BOX
5/BOX
25/BOX
25/BOX
4.54
4.54
6.82
8.29
9.57
15.36
17.86
156.07
5.29
4.54
22.89
180.93
56.68
184.46
75.04
405.54
4.79
5.57
*Sol d by box / MLP per each.
Insta-Charge
Faster, safer and more economical method for charging LIQUID refrigerant through the low pressure side of an air
conditioning or refrigeration system, without damaging the compressor. Insta- Charge’s unique internal restrictor reduces liquid flow to
a level below the capacity of the compressor. Converts liquid refrigerant to a saturated vapor for fast entry. Insta-Charge connects
directly to the refrigerant can or cylinder valve. Adds liquid tracing dye faster. Eliminates heating of refrigerant cylinder. Made of light
weight aluminum. Sold at a fraction of the cost of other fast charging devices.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-RC-1
INSTA-CHARGE
15.96
29
CPS Products Access Fittings
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CP-AD87
S1-CP-AD87S
FITTING,1/4" SAE M X F 1/2"-20 UNF ADPT
FITTING,R-410A 1/4" SAE X 5/16" ANG/SWVL
9.60
11.11
30
JB INDUSTRIES, INC. ACCESS FITTINGS
Adapter
• 1/4in. Male Flare x 1/2in. - 20 UNF Female
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-MSA-45
ADAPTER, 1/4" MALE FLARE x 20 UNF FEMALE
20.14
Adapters - Swivel Flare X Solder
Swivel flare X solder adapter. Double deep solder cups. High tensile strength. Corrosion resistant.
SOURCE 1 PART NO.
DESCRIPTION
DIA
MLP $
S1-A32700
S1-A32701
S1-A32702
S1-A32703
ADAPTER, SWIVEL x FLARE, PK OF 4
1/4"
3/8"
1/2"
5/8"
39.43
41.89
45.61
28.89
Copper Saddle Tappers
JB A32800 series saddles offer the best protection from leaks. Once brazed on, you can check for leaks before piercing the tube.
The steel pin is inserted and the cap is tightened down to pierce the tube. Body sizes are contoured to match specific tubs sizes.
Hardened steel piercing needle. Cap included
SOURCE 1 PART NO.
DESCRIPTION
DIA
MLP $
S1-A32804
S1-A32806
S1-A32812
S1-A32814
VALVE, SADDLE, TAP, PK OF 5
1/4"
3/8"
3/4"
7/8"
46.50
47.54
45.07
52.82
Copper Tube Extensions
Install through the side of the larger line to extend length approximately two inches. Includes a cap and valve core. High tensile
strength. Corrosion resistant.
SOURCE 1 PART NO.
DESCRIPTION
OD
MLP $
S1-A31002
S1-A31003
S1-A31005
S1-A31006
S1-A31008
TUBE, EXTENSION, COPPER, PK OF 5
TUBE EXTENSION, COPPER, PK OF 5
1/8"
3/16"
5/16"
3/8"
1/2"
25.39
25.36
28.96
28.57
43.11
Copper Tubing Cutters and Replacement Wheels
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-RT70007X
WHEEL,CUTTER,REPLACEMENT,PKG=10
129.96
Finger Tight Flare Cap
Neoprene O-Ring Seal
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-NFT5-4
1/4" FLARE REFRIGERANT CAP, PK OF 10
11.68
31
Flared Caps
SOURCE 1 PART NO.
DESCRIPTION
DIA
PACKAGE QTY
MLP $
S1-N5-10
S1-N5-12
S1-N5-4
S1-N5-5
S1-N5-6
S1-N5-8
FLARE REFRIGERANT CAP
5/8"
3/4"
1/4"
5/16"
3/8"
1/2"
10
2
25
5
25
10
6.32
18.25
1.29
3.21
1.93
2.75
Flared Tube Fittings
SOURCE 1 PART NO.
DESCRIPTION
DIA
MLP $
S1-A32600
S1-A32601
S1-A32602
S1-A32603
S1-A32604
SAE 45-DEGREE BRASS FLARED TUBE FITTINGS, PK OF 5
1/4"
5/16"
3/8"
1/2"
5/8"
19.07
19.29
23.82
15.96
23.54
Straight Quick Coupler
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-QC-S5
COUPLER,QUICK,5/16"QC x 1/4"SAE
18.43
Swaged Copper Braze Tees
Swaged copper braze tees allow for simple installation anywhere along the line. Braze cups on both
SOURCE 1 PART NO.
DESCRIPTION
OD
MLP $
S1-A31134
S1-A31135
S1-A31136
S1-A31138
S1-A31140
S1-A31142
S1-A31144
S1-A31334
S1-A31336
S1-A31338
S1-A31340
S1-A31342
S1-A31344
S1-A31348
TEE, COPPER, W/ ACCESS FTG, UNSWAGED, PK OF 3
TEE, COPPER, W/ ACCESS FTG, SWAGED, PK OF 3
TEE, COPPER, W/ACCESS FTG, PK OF 3
1/4"
5/16"
3/8"
1/2"
5/8"
3/4"
7/8"
1/4"
3/8"
1/2"
5/8"
3/4"
7/8"
1-1/8"
29.89
31.93
31.18
33.25
16.11
17.07
21.29
35.00
38.50
37.82
19.36
20.68
24.36
32.25
Swivel Cross
Add multiple ports with just one fitting
SOURCE 1 PART NO.
DESCRIPTION
OD
MLP $
S1-A31520
TEE, COPPER, W/ ACCESS FTG, SWAGED, PK OF 3
1/4"
46.50
32
Swivel Tees
Add multiple ports with just one fitting. The swivel flare connections offer a safe, simple installation without the need for brazing. All of
the flare ends are tapped to receive access core s. One core and one cap are packaged with each valve.
SOURCE 1 PART NO.
DESCRIPTION
S1-A31851
S1-A31852
S1-A31853
S1-A31854
S1-A31856
TEE,1/4",W/DEPRESSOR,PKG=3
TEE,1/4",W/DEPRESSOR,PKG=3
TEE, 3/8" SAE x 3/8" FE SAE SWIVEL x 1/4" ACCESS, PK OF 1
TEE,1/4",PKG=3
TEE, 3/8" SAE x 1/4" ACCESS x 3/8" FE SAE SWIVEL, PK OF 1
DEPRESSOR NUT ON
Yes
Yes
NO
Yes
NO
MLP $
Run
Branch
45.36
43.89
37.14
42.21
63.68
Branch
Tube Flaring Tool
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-RT222402
45-DEG ADJUSTABLE FLARING TOOL, 3/16 - 5/8"
414.29
Valve Core Removal Tool
• 1/4” valve core removal tool. Complete with a hollow handle for storing up to six extra valve cores. Made in the USA.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-A32004
TOOL, VALVE CORE REMOVAL
18.54
Valve Cores
PT FE/Neoprene seal replacement valve cores. Maximum 800 PSI and 220 degrees Fahrenheit (104 C). Made in the USA.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-A31999
S1-A31999-100
CORE, VALVE, 1/4", PK OF 5
CORE, VALVE, 1/4", PK OF 100
6.89
126.64
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-VA-46
S1-VAU-24
S1-VAU-45
S1-VAX-2
S1-VAX-3
S1-VAX-4
S1-VAX-5
S1-VAX-6
S1-VS-4
S1-VST-4
S1-VST-44
FTG,ACCESS,1/4",HALF UNION,BX OF 6
FTG, ACCESS,1/8" MPT, BX OF 6
FTG, ACCESS, 1/4" MPT, BX OF 6
FTG, ACCESS, 1/8", EXTENDED END, PK OF 6
FTG, ACCESS, 3/16",EXTENDED END, PK OF 6
FTG, ACCESS, 1/4" EXTENDED END
FTG, ACCESS, 5/16 IN. OD, EXTENDED END, 3-PK
FTG, ACCESS, 3/8" EXTENDED END
FTG, ACCESS, 1/4", SWIVEL NUT W/DEPR, PK 6
FTG, ACCESS, 1/4", SWIVEL T W/DEPR, PK
FTG, ACCESS, 1/4", SWIVEL T W/DEPR, PK 3
21.69
30.93
32.39
29.93
29.93
18.29
18.79
19.96
87.50
45.68
53.64
S1-VST-44B
FTG,ACCESS,1/4",SWIVEL T W/DEPR,BULK
17.86
S1-VST-44X
S1-VST-4X
S1-VTS-56
S1-VVC-1
FTG,ACCESS,1/4",SWIVEL T W/O DEPR,PK 3
FTG,ACCESS,1/4",SWIVEL T W/O DEPR,PK 3
FTG, ACCESS, 5/16" ODS TEE, PK OF 3
FTG, ACCESS ,REPL VALVE CORE, PK OF 6
53.64
41.50
38.00
4.18
LINE PIERCING VALVES AND TOOLS
Access Fittings
33
Copper Saddle Valve
For copper-to-copper brazing. Penetrates line in one easy operation with no holes to drill. Steel pin with valve core pierces line and is
locked into valve body by tightening cap. Teflon ring assure s positive seal. Available in sizes from 1/4” to 1-1/8”.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-VLC-10
S1-VLC-12
S1-VLC-18
S1-VLC-25
S1-VLC-4
S1-VLC-5
S1-VLC-6
S1-VLC-8
COPPER SADDLE VALVE – 5/8” O.D. TUBE SIZE
COPPER SADDLE VALVE – 1-1/8” O.D. TUBE SIZE
ADDITIONAL TEFLON RINGS
3
2
2
25
6
6
6
4
26.71
20.00
20.00
16.32
45.00
45.00
45.00
32.43
*Sold by pack / M LP per each
Core Removal Tool
Designed to remove and replace valve cores without losing the refrigerant charge. Connects to any 1/4” male flare fitting. Saves time,
saves refrigerant.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-VCRT-1
S1-VCRT-1R
S1-VCRT-1RK
S1-VCRT-1S
CORE REMOVAL TOOL
REPLACEMENT ROD ASSEMBLY
REPLACEMENT O-RING KIT
REPLACEMENT SHUT-OFF STEM
80.39
20.21
2.54
21.21
Core Storer
All steel valve core remover and storage container. Completely knurled for easier grip, eliminating slippage when using with oily or
greasy hands. Core Storer features a compartment for storing extra valve cores. Four replacement cores are included with each tool.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-VCR-1
CORE REMOVER AND STORER
15.36
Insta-Tap Refrigerant Recovery Tool
The fastest, easiest way to evacuate refrigerant before disposal of a unit. Snaps onto refrigerant line for full and immediate flow.
Punctures super large hole for maximum full flow discharge to recovery unit. One tool fits all sizes from 3/16” to 7/8” O.D. hard tubing.
Replaceable needle.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-QT-100
S1-QT-100G
S1-QT-100N
QUICK-TAP-2 – 1/4”, 5/16”, 3/8” O.D. TUBE SIZE
REPLACEMENT GASKET ONLY
REPLACEABLE HARDENED STEEL NEEDLE AND GASKET
1
3
1
102.64
9.32
11.18
*Sold by pack / MLP per each
34
Line Tap & Swivel Valves
The quick, safe and easy option to charge, discharge and test a line. Simply clamp on the DLT valve, attach the DCV-1G control
valve, and pierce the line. The control valve features a port for connecting charging lines or gauges. The valve can swivel to any
position and also be removed and re-used. These line tap valves are also difficult to tamper with as the line can only be accessed by
using the special DCV- 1G valve. They feature a specially formulated gasket which can withstand heat up to 302ºF. Available in four
sizes from 3/16” OD tube size to 3/8”. The DCV- 1G is designed for use with all four sizes. DLT series line taps are also compatible
with existing A-1 Components CV-1G valves and likewise DCV-1G valves are compatible with A-1 Components LT-series line taps.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-DCV-1G
S1-DLT-3G
S1-DLT-4G
S1-DLT-5G
S1-DLT-6G
VALVE FOR DLT LINE TAPS
LINE TAP VALVE – 3/16” OD TUBE
12.79
7.00
7.96
7.00
7.96
MAC - The Ultimate in Line Piercing Valves
Install valve. Connect charging hose. Service. That’s all there is to it MAC features uniport: 1 connection for piercing and servicing.
Sealed with refrigerant resistant “O” rings. Needle automatically back seats after servicing, leaving line free of restriction. Connect to
tubing with 2 socket-head screws. (Hex wrench is included with each valve.) Needle depressor is inserted into head of needle. Wing
cap is turned down easily by hand until line is pierced. Wing cap is removed and system may be serviced with any charging hose with
built-in depressor. When hose is removed, spring loaded needle backseats forming a leak proof seal. Needle depressor is discarded
and wing cap forms extra precautionary seal.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-QTM-1
S1-QTM-1B
S1-QTM-2
S1-QTM-2B
S1-QTM-3
MAC LINE PIERCING VALVE – 1/4”, 5/16”, 3/8” O.D. TUBE SIZE
MAC LINE PIERCING VALVE – 1/4”, 5/16”, 3/8” O.D. TUBE SIZE
MAC LINE PIERCING VALVE – 1/2”, 5/8” O.D. TUBE SIZE
36
100
36
100
36
8.14
7.39
8.82
8.71
10.00
*Sold by pack / MLP per each
Quick-Tap
Features Valve core in the 1/4” male port . Simply pierce the line and back seat the needle. Flow starts when depressor type charging
hose is connected. Flow shuts off automatically when hose is removed. If valve core is not desired, it may be removed. Connect hose,
pierce line and back seat needle. This method offers full unrestricted flow. Valve core can be removed or changed at any time without
loss of refrigerant if needle is front seated.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-QT-1
S1-QT-2
QUICK-TAP – 1/4”, 5/16”, 3/8” O.D. TUBE SIZE
QUICK-TAP – 1/2”, 5/8” O.D. TUBE SIZE
10.93
11.79
Quick-Tap-2
Identical to Quick-T ap except that a nylon handle replaces the hex wrench. Phillips-head screws are used.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-QTH-1
S1-QTH-2
QUICK-TAP-2 – 1/4”, 5/16”, 3/8” O.D. TUBE SIZE
QUICK-TAP-2 – 1/2”, 5/8” O.D. TUBE SIZE
17.43
18.61
35
REFRIGERANT LABELS
Identification Labels
Refrigerant ID Labels (3" X 4")
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-04010
S1-04011
S1-04012
S1-04022
S1-04056
S1-04123
S1-04134
S1-04401
S1-04402
S1-04404
S1-04407
S1-04410
S1-04414
S1-04451
S1-04500
S1-04507
R-408A (FX10) REFRIGERANT ID LABELS
R-11 REFRIGERANT ID LABELS
R-409A (FX56) REFRIGERANT ID LABELS
R-134A REFRIGERANT ID LABELS
R-401A (MP39) REFRIGERANT ID LABELS
R-402A (HP80) REFRIGERANT ID LABELS
R-404A (HP62/FX70) REFRIGERANT ID LABELS
R-407C (SUVA 9000/KLEA 66) REFRIGERANT ID LABELS
R-410A (AZ20) REFRIGERANT ID LABELS
R-414B REFRIGERANT ID LABELS
R-401B (MP66) REFRIGERANT ID LABELS
R-507 (AZ50) REFRIGERANT ID LABELS
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10.11
10.11
9.54
10.11
10.11
10.11
10.11
10.11
10.11
10.11
10.11
10.11
10.11
10.11
10.11
10.11
Non-Flammable Gas Labels (4" X 4")
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-04700
NON FLAMMABLE GAS LABELS
10
10.11
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-04850
S1-04852
REFRIGERANT REMOVED LABELS
SYSTEM REFRIGERANT/OIL LABELS
10
10
10.11
10.11
System Refrigerant/Oil Labels (3" X 4")
System Lubricant Identification Labels (2" X 3")
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-04870
S1-04871
S1-04872
POLYOL ESTER OIL LABELS
MINERAL OIL LABELS
ALKYLBENZINE OIL LABELS
10
10
10
10.11
10.11
10.11
36
—NOTES—
37
—NOTES—
38
—NOTES—
39
—NOTES—
40
Thermostats
RESIDENTIAL & COMMERCIAL ACCESSORY THERMOSTATS
Source 1 CTS-Series Color Touchscreen Thermostats
Source 1 CTS-Series thermostats are suitable for residential gas/electric, heat pump, or multistage systems. Additional models,
including for commercial applications, will be introduced soon. They feature a high-resolution color touchscreen user interface that can
be customized to provide simple thermostat operation or to take advantage of a full range of programmability and display options,
including personalized screen savers and wallpaper.*
Features:
• 8.1 sq. in. (4.3 in. diagonal) high-resolution color display with touchscreen control
• Simple, plain text menus guide through setup and programming steps
• Personalized screensavers and wallpaper*
• Meets California Title 24 specifications
• Up to 4 stages heating and 2 stages cooling
• Up to 7-day installer selectable programming
• Auto changeover (switchable to manual)
• Built-in compressor protection (defeatable for zoning applications)
• Adjustable timers and deadbands
• Setpoint limiting
• Programmable fan
• Auxiliary heat indicator
• Auxiliary heat lockout
• Fahrenheit/Celsius display
• Choice of English, Spanish, or French
• Service filter reminder
• UV lamp replacement reminder
• Energy usage information
• Remote (hardwired) outdoor temperature sensor ready
• Dual fuel capable
Specifications:
Power Method
: Hardwired
Electrical Ratings
: 24 VAC +/-15%
Frequency
: 60Hz; 50Hz
Terminal Load
: Y1, Y2, G 1.5A per terminal, all others 0.5A per terminal
Setpoint Temperature Range (heating)
: 35-99F (1.5-37C)
Setpoint Temperature Range (cooling)
: 35-99F (1.5-37C)
Deadband Differential
: 1-6F (0.5-3C)
Operating Ambient
: 35-105F (1.5-41C)
Operating Humidity
: 5-90% RH, non-condensing
Dimensions
: 5.375” W x 4.0” H
Mounting
: Horizontal
STAGES
SOURCE 1 PART NO.
HEAT
COOL
PROGRAMMING OPTIONS
S1-TBPU32HP7S
3 (4 FOR
HEATPUMP)
2
365-DAY, 7-DAY, 5+2 DAY,
1-DAY, NONE
S1-TBPU32P7S
3 (4 FOR
HEATPUMP)
2
S1-THPU32HP7S
3 (4 FOR
HEATPUMP)
2
S1-THPU32P7S
3 (4 FOR
HEATPUMP)
2
CONTROL
COMMERCIAL MULTI-STAGE
HEATPUMP, GAS/ELECTRIC, AND
DUAL FUEL WITH HUMIDITY
CONTROL
365-DAY, 7-DAY, 5+2 DAY,
COMMERCIAL MULTI-STAGE
1-DAY, NONE
DUAL FUEL
RESIDENTIAL MULTI-STAGE
7-DAY, 5+2 DAY, 1-DAY, NONE
DUAL FUEL WITH HUMIDITY
CONTROL
RESIDENTIAL MULTI-STAGE
7-DAY, 5+2 DAY, 1-DAY, NONE
DUAL FUEL
TERMINALS
MLP $
W3, W2, W1/O/B, Y2, Y1, G,
R, C, OUTDOOR (2
POSITION)
417.86
W3, W2, W1/O/B, Y2, Y1, G,
R, C, OUTDOOR (2
POSITION)
W3, W2, W1/O/B, Y2, Y1, G,
R, C, OUTDOOR (2
POSITION)
375.00
W3, W2, W1/O/B, Y2, Y1, G,
R, C, OUTDOOR (2
POSITION)
375.00
417.86
*Requi res optional SD card for setup
CTS Series Thermostat Accessories
Indoor/Outdoor Hardwired Temperature Sensor for CTS Series Thermostats
• Use for either indoor or outdoor temperature sensing
• Hardwired
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CTSHTS
INDOOR/OUTDOOR HARDWIRED TEMPERATURE SENSOR FOR CTS SERIES
THERMOSTATS
24.11
41
Thermostats
CTS Series Thermostat Accessories
Wall Plate For CTS Series Thermostats
• Easily cover paint discrepancies or wall blemishes left after removal of old thermostats.
• Slim, attractive design.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CTSPLATE
WALL PLATE FOR CTS SERIES THERMOSTATS
12.50
Internet Access Module for CTS Series Thermostats
Compatible with Apple iPhone®, iPod Touch®, iPad®, Blackberry®, Android®, Mac and PC devices
Benefits:
• Monitor thermostat information, including system run time and current usage
• View incoming alerts based on pre-configured notifications, such as important updates on the health of the system or simply if the
home's inside temperature has gone above or below pre-set limits
• View a pictorial display of the current weather and weather forecast for all thermostat locations
• Send text messages from the mobile device to the thermostat display, such as reminders and notes to family members
• Receive vital updates from their HVAC professionals on the health of their systems right on the thermostat display
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CTSIAM
INTERNET ACCESS MODULE FOR CTS SERIES THERMOSTATS
125.00
Source 1 LX-Series Thermostats
Residential Models
STAGES
SOURCE 1 PART NO.
HEAT
COOL PROGRAMMING
OPTIONS
1
1-DAY, NONE
S1-THSU21P1S
2
S1-THSU32HP7S
3 (4 FOR
HEATPUMP)
2
S1-THSU32P7S
3 (4 FOR
HEATPUMP)
2
CONTROL
TERMINALS
R, C, G, W1/O/B, W2, Y1, OUTDOOR SENSOR,
DRY CONTACT, FAULT
7-DAY, 5+2 DAY, MULTI-STAGE HEAT PUMP, GAS/ELECTRIC, R, C, G, W1/O/B, W2, W3, Y1, Y2, HUM, DEHUM,
1-DAY, NONE
HUMIDIFICATION, DEHUMIDIFICATION,
AUX, OUTDOOR SENSOR, REMOTE SENSOR,
REHEAT, AND DUAL FUEL
DRY CONTACT, FAULT
7-DAY, 5+2 DAY, MULTI-STAGE HEAT PUMP, GAS/ELECTRIC R, C, G, W1/O/B, W2, W3, Y1, Y2, OUTDOOR
1-DAY, NONE
SENSOR, REMOTE SENSOR, DRY CONTACT,
FAULT
HEAT PUMP, GAS/ELECTRIC
MLP $
116.96
221.43
176.79
LX-Series Thermostat Accessories
Comfort Call Accessory For LX-Series Thermostats
•
•
•
•
•
•
•
•
Requires wireless transceiver module.
Allows simple remote control of the thermostat from any phone.
Voice recognition or touch-tone entry.
Announces indoor and outdoor temperatures/indoor humidity.
Announces sy stem status.
Controls up to four thermostats.
Can control one auxiliary output.
Easy to install.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-LXCC
COMFORT CALL ACCESSORY FOR LX-SERIES THERMOSTATS
187.50
Plug-In Usb Port Programmer For LX-Series Thermostats
•
•
•
•
•
•
Program on your computer with intuitive software.
Works with pc or mac.
Customize messages to appear on thermostat display.
Quick and easy copying from one thermostat to the next.
Battery backup maintains current time and day of the week.
Stores data from several models simultaneously.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-LXPROG
PLUG-IN USB PORT PROGRAMMER FOR LX-SERIES THERMOSTATS
85.71
42
Thermostats
900 Mhz Wireless Transceiver Module For LX-Series Thermostats
•
•
•
•
Two way wireless communication.
Links multiple sensors and accessories to the thermostat.
Frequency hopper to avoid interference.
Easy two minute installation.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-LXRFM
900 MHZ WIRELESS TRANSCEIVER MODULE FOR LX-SERIES THERMOSTATS
57.14
Indoor/Outdoor Wireless Temperature Sensor For LX-Series Thermostats
•
•
•
•
Requires wireless transceiver module.
Automatic remote sensor averaging when using more than one (indoor) sensor.
Can link with up to four thermostats.
Long battery life.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-LXRFTS
INDOOR/OUTDOOR WIRELESS TEMPERATURE SENSOR FOR LX-SERIES
THERMOSTATS
81.25
Source 1 LX-Series Thermostats
Commercial Models
STAGES
SOURCE 1 PART NO.
HEAT
COOL
PROGRAMMING
OPTIONS
NON-PROGRAMMABLE
S1-TBSU22HNS
2
2
S1-TBSU32HP7S
3 (4 FOR
HEATPUMP)
2
7-DAY, 5+1+1 DAY,
1-DAY, NONE
S1-TBSU32P7S
3 (4 FOR
HEATPUMP)
2
7-DAY, 5+1+1 DAY,
1-DAY, NONE
CONTROL
TERMINALS
MLP $
MULTI-STAGE HEAT PUMP,
GAS/ELECTRIC HUMIDIFICATION,
DEHUMIDIFICATION
GAS/ELECTRIC, HUMIDIFICATION,
DEHUMIDIFICATION, AND REHEAT
GAS/ELECTRIC
R, C, G, W1/O/B, W2, Y1, Y2, HUM, DEHUM,
OUTDOOR SENSOR, DRY CONTACT, FAULT
182.14
R, C, G, W1/O/B, W2, W3, Y1, Y2, AUX, HUM,
DEHUM, OUTDOOR SENSOR, REMOTE
SENSOR, DRY CONTACT, FAULT
R, C, G, W1/O/B, W2, W3, Y1, Y2, OUTDOOR
SENSOR, REMOTE SENSOR, DRY
CONTACT, FAULT
228.57
305.43
Hardwired Outdoor Temperature Sensor
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-8052
HARDWIRED OUTDOOR TEMPERATURE SENSOR
14.82
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-8053
HARDWIRED INDOOR TEMPERATURE SENSOR
28.46
Hardwired Indoor Temperature Sensor
Locking Ring For LX-Series Thermostats
•
•
•
•
•
Designed for easy tool-less slip-on installation and slip-off removal.
Thermostat removal or wiring disconnection not required for installation.
Can be combined with keypad lockout or setpoint limits.
Locks both front and back thermostat housings to the wall.
Elegant style and security at an affordable price.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-LXLOCK
LOCKING RING FOR LX-SERIES THERMOSTATS
26.79
Wall Plate For LX-Series Thermostats
• Easily cover paint discrepancies or wall blemishes left after removal of old thermostats.
• Slim, attractive design.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-LXPLATE
WALL PLATE FOR LX-SERIES THERMOSTATS
14.29
43
Thermostats
Add-A-Wire Accessory For All Conventional Thermostats
• One wire to run two wires worth of comm unication in applications Where additional wire cannot be run.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ADDWIRE
ADD-A-WIRE ACCESSORY FOR ALL CONVENTIONAL THERMOSTATS
39.29
RESIDENTIAL ACCESSORY THERMOSTATS
Source 1 Value Series Thermostats
Features:
• Large digital display; programmable models are backlit
• Up to 2 stages heating and 2 stages cooling
• Battery or system powered
• Auxiliary heat indicator for heat pump models
• Fahrenheit or Celsius
• Separate mounting plate
• Manual changeover (except S1-THEM22P7S)
• Custom contractor logo available on battery covers for battery-powered models. Order S1-THEBATTCVR.
• Commercial model includes auto changeover, clock backup, up to 4-hour override, and keypad lockout
Accessories:
• Locking cover ring (S1-THELOCK)
• Decorative wall mounting backplate (S1- THEPLATE)
• Add-a-Wire Accessory (S1-ADDWIRE)
STAGES
SOURCE 1 PART NO.
S1-TBEU22P7S
S1-THEC11NS
S1-THEC11P5S
S1-THEH21NS
S1-THEH21P5S
S1-THEU21P7S
S1-THEU22P7S
HEAT COOL PROGRAM
2
1
1
2
2
2
2
2
1
1
1
1
1
2
7 DAY
N/A
5-2 DAY
N/A
5-2 DAY
7 DAY
7 DAY
APPLICATIONS
POWER SOURCE
MLP $
COMMERCIAL MULTI-STAGE HEAT PUMP, GAS/OIL/ELECTRIC
SINGLE-STAGE HEAT PUMP, GAS/OIL/ELECTRIC, MILLIVOLT
HEAT PUMP
HEAT PUMP
HEAT PUMP OR CONVENTIONAL
MULTI-STAGE HEAT PUMP, GAS/OIL/ELECTRIC
HARDWIRED
HARDWIRED OR BATTERY
HARDWIRED
HARDWIRED
160.71
60.71
76.79
80.36
98.21
116.96
139.29
Value Series Thermostat Accessories
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ADDWIRE
S1-THELOCK
S1-THEPLATE
ADD-A-WIRE ACCESSORY FOR ALL CONVENTIONAL THERMOSTATS
LOCKING COVER FOR S1-THE SERIES THERMOSTATS
WALL MOUNTING PLATE FOR S1-THE SERIES THERMOSTATS
39.29
26.79
7.14
44
Thermostats
Universal 4-Wire Thermostat Solution
Features:
• Upgrade single stage applications to premium high-efficiency systems (staging, heat pump or heat pump with dual fuel) – using
existing 4 wires
• Dual fuel heat pump control (requires outdoor remote sensor)
STAGE
SOURCE 1 PART NO.
DISPLAY SIZE
SINGLE
MULTI
HEAT PUMP
PROGRAM
APPLICATIONS
POWER
MLP $
S1-1F98EZ-1421
12
1/1
2/2
4/2
7-DAY, NO
GAS/OIL/ELECTRIC
HARDWIRED
552.36
Emerson BlueTM Universal Touchscreen Thermostats
Features:
• Automatic heat/cool changeover option
• Installer-selectable system applications and programs
• 12-square-inch lighted display is the largest in the industry
• 4 time and 4 temperature settings per program (2 setbacks) heat and cool, or selectable— 2 time and 2 temperature settings (1
setback)
• Selectable Energy Management Recovery
• Permanent program retention during power outages
• Compressor lockout protection
• Maintains room temperature to within ±1°
• Programmable Fan and Remote Sensing available for S1-1F95-1277 and S1-1F97- 1277
Specifications:
Dimensions: 4.6”H x 5.9”W x 1.2”D
Setpoint Temperature Range: 45°–99°F (7–32°C)
Rated Differential: Heat 0.6°F; Cool 1.2°F
Operating Ambient Temperature: 32°–105°F (0°–41°C)
Operating Humidity Range: 90% non-condensing maximum
Electrical:
Battery: mV to 30 VAC, NEC Class II, 50/60 Hz or DC
Input-Hardw ire: 20–30 VAC 1.5A load per terminal; 2.5A maximum load (all terminals combined)
SYSTEM/STAGES
(HEAT/COOL)
SOURCE 1 PART NO.
S1-1F95-1277
S1-1F95-1280
DISPLAY
SIZE (SQ.
IN.)
12.0
12.0
S1-1F95-1291
12.0
S1-1F97-1277
12.0
APPLICATIONS
SINGLE MULTI HEAT PROGRAM
STAGE STAGE PUMP
GAS/OIL/ELECTRIC, MILLIVOLT 3-WIRE ZONE VALVE
COMMERCIAL GAS/OIL/ELECTRIC, MILLIVOLT 3-WIRE ZONE
VALVE
GAS/OIL/ELECTRIC, MILLIVOLT 3-WIRE ZONE VALVE,
HUMIDIFY/DEHUMIDIFY
MLP $
1/1
1/1
2/2
2/2
3/2
4/2
7, 5/1/1, 0
7, 5/1/1, 0
417.71
495.57
1/1
2/2
4/2
7, 5/1/1, 0
454.00
1/1
—
1/1
7, 5/1/1, 0
373.96
Indoor Temperature Sensor
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-F145-1328
INDOOR TEMPERATURE SENSOR
67.39
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-F145-1378
OUTDOOR TEMPERATURE SENSOR
78.54
Outdoor Temperature Sensor
45
Thermostats
EMERSON DIGITAL THERMOSTATS
Emerson BlueTM 4-Inch & 6-Inch Thermostats
Features:
• Configures as manual heat/cool, auto changeover, heat only or cool only
• Exclusive Cool Savings feature saves energy during peak A/C demand periods
• Hydronic 2- or 3-wire applications
• Three anticipation settings
• Exclusive battery power monitor
• Easy access battery compartment
• Permanent program retention during power loss
Specifications:
Dimensions: 4.5”W x 3.5”H x 1.1”D
Electrical: Rating 0–30 VAC, 50/60 Hz or DC
Load (per terminal): 0.05–1.0 A
Load (all terminals combined): 1.5 A maximum
Setpoint Temperature Range: 45°–90°F (7°– 32°C)
Differential: 0.4°–1.7°F with adjustable anticipation
Accessories: Wall plate, 6.5”W x 5”H (vendor part number F61-2634) included with S1-1F80- 0471
SYSTEM/STAGES
SOURCE 1 PART NO.
S1-1F80-0471
DISPLAY SINGLE STAGE
SIZE (SQ.
IN.)
4.0
1/1
MULTI
STAGE
HEAT
PUMP
-
1/1
S1-1F80ST-0471
4.0
1/1
-
1/1
S1-1F83-0422
4.0
1/1
2/2
2/1
S1-1F85-0422
4.0
1/1
2/2
2/1
S1-1F85-0477
4.0
1/1
2/2
3/2
S1-1F85CA-0471
4.0
1/1
2/2
3/2
S1-1F85ST-0422
4.0
1/1
2/2
2/1
S1-1F86-0471
4.0
1/1
-
1/1
S1-1F86ST-0471
4.0
1/1
-
1/1
S1-1F95-0671
6.0
1/1
2/2
4/2
S1-1F95EZ-0671
6.0
1/1
2/2
4/2
PROGRAM
APPLICATIONS
POWER
5/1/1, 5/2, 0 GAS/OIL/ELECTRIC, MILLIVOLT 3-WIRE
BATTERY,HARDWIRED
ZONE VALVE
BATTERY,HARDWIRED
ZONE VALVE
GAS/OIL/ELECTRIC, MILLIVOLT 3-WIRE
BATTERY,HARDWIRED
ZONE VALVE
BATTERY,HARDWIRED
ZONE VALVE
GAS/OIL/ELECTRIC,SINGLE
STAGE
7.5/1/1, 5/2
BATTERY,HARDWIRED
HEAT PUMP, MULTI STAGE HEAT
PUMP,MILLIVOLT, 3-WIRE ZONE VALVE
BATTERY,HARDWIRED
ZONE VALVE
BATTERY,HARDWIRED
ZONE VALVE
BATTERY,HARDWIRED
ZONE VALVE
BATTERY,HARDWIRED
ZONE VALVE
7, 5/1/1, 0 GAS/OIL/ELECTRIC, MILLIVOLT 3-WIRE BATTERY,HARDWIRED POWER ASSIST
ZONE VALVE
GAS/OIL/ELECTRIC, MILLIVOLT 3-WIRE BATTERY,HARDWIRED POWER ASSIST
0, 7
ZONE VALVE
46
MLP $
156.43
161.29
143.96
196.64
228.82
247.57
190.86
107.04
118.82
297.14
258.89
Thermostats
EMERSON DIGITAL THERMOSTATS
Emerson BlueTM 2-Inch Thermostats
For Single-Stage & Heat Pump Applications
Features:
• Easy-to-read lighted LCD display
• Dual-powered—choice of battery-powered or hardwired for all applications
• Fast (FA) or slow (SL) heating cycle anticipation
• Easy-to-wire push-connect color-coded terminals
• Compressor lockout protection
• Millivolt compatible
• Electric heat option
Programmable Model Features:
• 4 time and 4 temperature settings per program (heat and cool)
• Energy savings up to 33%
• Permanent program retention during power loss
• Setpoint Hold
• Temporary temperature override two-hour minimum or until next program period
• Selectable Energy Management Recovery
• Meet Energy Star specifications (S1-1F82- 0261 & S1-1F80-0261)
• Meets California Building Code, Title 24
Specifications:
Dimensions: 4.8”W x 3.8”H x 1.5”D
Electrical Rating: 0–30 VAC, 50/60 Hz or DC, 0.05–1.5 Amps (load per terminal), 1.5 Amps maximum load (all terminals combined)
Standard Systems: gas, oil, electric, single stage/heat pump, millivolt
Setpoint Temperature Range: 45°F–90°F (7°–32°C)
Rated Differential: 0.6°–1.7°F with adjustable anticipation
Shipping Temperature Range: –40°–150°F (–40°–65°C)
STAGES
SOURCE 1 PART NO. DISPLAY
SIZE (SQ.
IN.)
S1-1F80-0224
2.0
S1-1F80-0261
2.0
S1-1F82-0261
2.0
S1-1F86-0244
2.0
S1-1F86EZ-0251
2.0
S1-1F89-0211
2.0
APPLICATIONS
GAS/OIL/ELECTRIC,MILLIVOLT
HEAT PUMP
GAS/OIL/ELECTRIC, MILLIVOLT
HEAT PUMP
HEAT COOL
1
1
2
1
1
2
1
1
1
1
1
1
PRGM
POWER
ENERGY MANAGEMENT
RECOVERY
TERMINATIONS
MLP $
24-HOUR
5/1/1
5/1/1
—
NO
—
BATTERY,HARDWIRED
BATTERY,HARDWIRED
BATTERY,HARDWIRED
BATTERY,HARDWIRED
BATTERY,HARDWIRED
BATTERY,HARDWIRED
YES
YES
YES
NO
NO
NO
R, C, Y, W, G, O/B
R, C, Y, W, G, O/B
R, C, Y, W2, G, O/B, L
R, C, Y, W, G, O/B
R, C, Y, W, G, O/B
R, C, Y, W2, G, O/B, L
107.61
139.61
154.89
98.43
121.32
128.57
47
Thermostats
HONEYWELL DIGITAL THERMOSTATS
Prestige SD Comfort System Kit
TM
Honeywell’s Prestige is a high-definition, full-color thermostat that redefines how a thermostat can look and what a thermostat can do.
Programming is easy with Prestige’s patented, interview-based setup and touchscreen interaction. The RedLINKT M wireless technology
built in provides endless possibilities for controlling and monitoring comfort inside your home. There’s simply nothing else like it.
Features:
• High-Definition, Full Color Display
• Precise Temperature Control
• Simple Touchscreen Technology
• Interview based programming up to 7 days
• Wireless remote and sensor ready
• All-In-One Control
Application:
Up to 2 Heat/2 Cool Conventional Systems and up to 3 Heat/2Cool Heatpumps
Programmability:
7-day or Non-programmable
Changeov er:
Auto or Manual
Electrical Ratings:
18 to 30 VAC
System Sw itch Positions:
HEAT-OFF-COOL-AUTO-EM.HEAT
Fan Sw itch Positions:
AUTO-ON-CIRC
Terminal Designations:
C,R,RC,W-0/B,W2-AUX/E,Y2,G,L,K,HUM,DHM,DHM
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-YTHX9321R1000
STANDARD DEFINITION TOUCHSCREEN THERMOSTAT WITH REM5000R1001 PORTABLE
COMFORT CONTROL AND C7089R1013 WIRELESS OUTDOOR SENSOR
HIGH DEFINITION COLOR TOUCHSCREEN THERMOSTAT WITH REM5000R1001
PORTABLE COMFORT CONTROL AND C7089R1013 WIRELESS OUTDOOR SENSOR
HIGH DEFINITION COLOR TOUCHSCREEN THERMOSTAT WITH C7089R1013 WIRELESS
OUTDOOR SENSOR
PRESTIGE IAQ 2.0 SYSTEM KIT INCLUDING: PRESTIGE IAQ 2.0 HD THERMOSTAT,
EQUIPMENT INTERFACE MODULE (EIM), PORTABLE COMFORT CONTROL,
WIRELESSOUTDOOR TEMPERATURE SENSOR AND TWO DUCT SENSORS FOR ALERTS
AND DIAGNOSTICS.
994.00
S1-YTHX9321R5003
S1-YTHX9321R5012
S1-YTHX9421R5077
48
1003.64
799.04
1076.79
Thermostats
VisionPRO® IAQ Total Home Comfort System
The VisionPro IAQ Total Home Comfort System features an effortless, 7- day programmable touchscreen thermostat that provides
control of temperature, humidification, dehumidification, and ventilation.
Features:
• Large, clear display with backlight shows the current and set temperature and time—even in the dark
• Touchscreen interaction
• Real-time clock keeps time during power failures and automatically updates to daylight savings
• Change/check reminders let you know when to service or replace filters
• Various Hold options allow you to override the program schedule, as desired
• Controls dehumidification using air conditioner with high or low speed fan or a whole house dehumidifier
• Controls ventilation with other HRV, ERV or Fresh air damper. Vent on demand and automatically using patented advanced
ventilation control
• Advanced heat pump control featuring balance point plus 2-5°F adjustable to increase homeowner comfort
Specifications:
Electrical Ratings: Voltage 20–30 VAC at 50/60 Hz; Running Current 0.02–1.0A
Temperature Setting Range: Heating: 40°–90°F (4.5°–32°C); Cooling: 50°–99°F (10°–37°C)
Humidification Setting Range: Heating, 10%–60% RH
Dehumidification Setting Range:
Heating: 40%–80% RH
Humidity Display Range: 0%–99%
STAGES
SOURCE 1 PART NO.
APPLICATIONS
HEAT
COOL
POWER SOURCE
MLP $
S1-YTH9421C1002
GAS/OIL/ELECTRIC HEAT WITH AIR CONDITIONING WARM AIR, HOT
WATER, HIGH-EFFICIENCY FURNACES HEAT PUMPS STEAM AND
GRAVITY HEAT ONLY WITH FAN, COOL ONLY
GAS/OIL/ELECTRIC HEAT WITH AIR CONDITIONING WARM AIR, HOT
WATER, HIGH-EFFICIENCY FURNACES HEAT PUMPS STEAM AND
GRAVITY HEAT ONLY WITH FAN, COOL ONLY OUTDOOR
TEMPERATURE SENSOR INCLUDED
4
2
COMMON WIRE ONLY
648.64
4
2
COMMON WIRE ONLY
698.57
S1-YTH9421C1010
49
Thermostats
VisionPRO® Universal Programmable Thermostat
The TH8110U Universal Programmable Thermostats provide electronic control of 24 VAC heating and cooling systems or 750 mV
heating systems.
Features:
• Large, Clear Display with Backlighting current temperature, set temperature and time are easy-to-read and all are displayed on the
home screen.
• Menu Driven Programming Guides you through the scheduling process, showing only necessary information and choices on each
screen.
• Ability to Select Multiple Days allows you to easily customize the thermostat for your unique schedule.
• Real-Time Clock keeps time during power failure; automatically updates for daylight savings.
• Armchair Programming allows you to remove thermostat from wall to set the schedule.
• Precise Temperature Control (+/- 1 F) reliable, consistent comfort.
• Multiple HOLD options allows you to modify schedule indefinitely or for a specific time.
• Change Reminders reminds you to service or replace the air filter, humidifier pad, ultraviolet lamp or thermostat batteries.
• Programmable fan with auto, on, and circulate options.
• Outdoor Temperature Indication (Select Models) shows current outdoor temperature on the display to help you plan outdoor
activities.
Specifications:
Application: Heating and Cooling systems
Programmability: Universal Programming from 7 Day to Non-Programmable
Changeov er: Automatic
Color: Premier White®
Sw itch Positions (System): HEAT-OFFCOOL-AUTO
Sw itch Positions (Fan): AUTO-ON
Power Method: Battery or Hardwired
Dimensions (in.): 4-9/16”H x 6”W x 1-1/4”D
Mounting: Horizontal
Electrical Ratings: 20 to 30 VAC
Frequency: 60 Hz; 50 Hz
Setting Temperature Range (F): Heat: 40°F to 90°F; Cool: 50°F to 99°F
Setting Temperature Range (C): Heat: 4.5°C to 32°C; Cool: 10°C to 37°C
Differential Temperature (F): 1°F
Differential Temperature (C): 0.5°C
Stages: Up to 3 Heat/2 Cool
Outdoor Sensor: Yes, optional outdoor remote (S1-C7089U1006).
Remote Sensor: Yes, optional indoor remote (S1-C7189U1005).
Sensor Element: Thermistor
Currents (Heating): 1.0 A running
Currents (Cooling): 1.0 A running
Currents (Fan): 0.6A running
Humidity Ratings (%RH): 5 to 90% RH, noncondensing
STAGES
SOURCE 1 PART NO.
S1-TH8110U1003
S1-TH8320U1008
DESCRIPTION
TERMINAL DESIGNATIONS
DOWN SELECTABLE TO HEAT ONLY OR COOL ONLY
R,RC,C,W,(O/B),Y,G,S1,S2
WORKS WITH CONVENTIONAL AND HEAT PUMP SYSTEMS. R, RC, W(O/B), W2(Aux), Y, Y2, L, E,
EMERGENCY HEAT SWITCH POSITION VAILABLE WHEN
G, C, S1, S2
SETUP FOR HEAT PUMP SYSTEMS. THE L TERMINAL IS AN
INPUT OR OUTPUT
WORKS WITH CONVENTIONAL AND HEAT PUMP SYSTEMS. R, RC, W(O/B), W2(Aux), Y, Y2, L, E,
EMERGENCY HEAT SWITCH POSITION VAILABLE WHEN
G, C, S1, S2
SETUP FOR HEAT PUMP SYSTEMS. THE L TERMINAL IS AN
INPUT OR OUTPUT
S1-TH8321U1006
HEAT
COOL
MLP $
UP TO 1
UP TO 3
1
UP TO 2
382.79
430.68
UP TO 3
UP TO 2
487.57
THM5320R1000 Equipment Interface Module
Easily relocate thermostat or upgrade equipment without running new wires using this module and a wireless FocusPRO® thermostat.
Features:
• Powered by RedLINK™ reliability
• No interference with other wireless devices in the home
• Works with TH6320R1004 or TH5320R1002 Wireless FocusPRO ® thermostats
• Input for Return Air Sensor
• Quick-connect terminal blocks
• LEDs for power and system status
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-THM5320R1000
RF EQUIPMENT INTERFACE MODULE
308.82
50
Thermostats
THM6000R1002 RedLINK Internet Gateway
Product Specifications:
• Application - Internet control of RedLINK thermostats; Up to 4 Heat/2 Cool Heat Pumps
• Dimensions (in.) - 3 15/16 in. High, 6 7/8 in. Wide, 1 1/2 in. Deep; 6 in. long X 5 in. tall X 2 1/2 in. wide
• Includes 3 Foot Ethernet Cable and Plug in Power Adapter
• Used With RedLINK™ enabled thermostats and accessories
• Electrical Ratings - 20 to 30 Vac
• Stages - See Equipment Interface Module
• Electrical Connections - Screw terminals; 24 Volt plug in transformer
• Operating Humidity Range (% RH) - 5 to 90% RH, non-condensing
• Supply Voltage - 18 to 30 Vac
• Switch Positions (System) - HEAT-OFF-COOL-AUTO-EM.HEAT
• Operating Temperature Range (F) - 32 F to 120 F
• Operating Temperature Range © - 0 C to 48.9 C
• Power Method - 24 Volt Plug In Transformer; Hardwired
• Terminal Designations - R, C then RedLINK to Equipment Interface Module
• External Sensors Available - Outdoor (optional)
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-THM6000R1002
RF EQUIPMENT INTERFACE MODULE
250.93
C7089 Outdoor Sensor for TH8000 Thermostats
Specifications:
Display Range: –40° to 127°F (–40° to 53°C)
Sensor Accuracy: ±1.5°F at 70°F (±0.84°C at 21°C)
Dimensions: 2-1/4” x 3/8” with 60” leadwires (57mm x 10mm with 1524mm leadwires)
SOURCE 1
PART NO.
APPLICATIONS
OPERATING RELATIVE
HUMIDITY
S1-C7089U1006 USED WITH TH9000 AND TH8000 THERMOSTAT FAMILIES ALSO SUITABLE FOR USE WITH SOURCE 1
COLOR TOUCHSCREEN THERMOSTAT S1-THPU32P7S.
5% TO 95%
NON-CONDENSING
OPERATING
MLP $
TEMPERATURE RANGE
(AMBIENT)
–40° TO 120°F (–40° TO 57.21
49°C)
C7089R Wireless Outdoor Temperature Sensor
Senses outdoor temperature and humidity to display on RedLINK™ enabled thermostats and accessories
Features:
• Reliable performance in all climates
• Installs in minutes
• Up to 5 year battery life
• 2 month low battery warning
• Battery warning displayed on RedLINK™ enabled thermostats
• Includes 2 AA Lithium batteries and mounting hardware
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-C7089R1013
WIRELESS OUTDOOR TEMP/HUM SENSOR
135.07
C7189 Indoor Remote Temperature Sensor
Specifications:
Operating Ambient Temperature Range: 45° to 88°F (7.2° to 32°C)
Display Range: 0° to 99°F (–18° to 37°C)
Sensor Accuracy: ±1.5°F at 70°F (±0.84° at 21°C)
Operating Relative Humidity: 5% to 95% non-condensing
Finish: White
Resistance Characteristics: Negative temperature coefficient (NTC). Resistance decreases as the temperature increases.
Dimensions in inches (mm): 1-1/2 (38) wide x 2-1/4 (57) high x 3/4 (19) deep.
Distance: Maximum distance between thermostat and sensor is 200 feet.
SOURCE 1 PART
NO.
S1-C7189U1005
APPLICATIONS
INDOOR REMOTE TEMPERATURE SENSORS FOR USE WITH TH9000 AND TH8000 THERMOSTAT FAMILIES
51
OPERATING TEMPERATURE
RANGE
45° TO 88°F (7.2° TO 32°C)
MLP $
70.79
Thermostats
C7189R Wireless Indoor Temperature Sensor
Used to sense indoor temperature remotely
Features:
• Used to sense temperature if the thermostat is installed in a poor temperature sensing location.
• Small remote temperature sensor to match any room decor.
• Easy to install and use.
• Factory calibrated; no field calibration required.
• Works with a maximum 200 foot wire run.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-C7189R1004
WIRELESS INDOOR TEMPERATURE SENSOR
96.46
Digital Non-Programmable VisionPRO® TH5110, TH5220 & TH5320 Thermostats
FocusPRO non-programmable digital thermostats provide electronic control of 24 VAC conventional and heat pump systems or 750
mV heating systems.
Features:
• Non-programmable digital thermostat.
• Large, clear, backlit display - easy to read in various lighting conditions.
• Display size options - available in large screen or standard.
• Precise comfort control (±1°F) – maintains consistent comfort to the highest level of accuracy.
• Easy change battery door - flip out door allows for easy battery replacement without removing or disassembling the thermostat.
Specifications:
Mounting: Horizontal
Changeov er: Automatic/Manual Selectable
Color: Premier White
Power Method: Battery or Hardwired
Fan Sw itch Positions: AUTO-ON
Sw itch Type: Relay
Setting Temperature Range: Heat: 40°F– 90°F; Cool: 50°F–99°F (Heat: 4.5°C–32°C; Cool: 10°C–37°C)
Sensor Element: Thermistor
Ambient Temperature Range: 32°F–120°F (0°C–48.9°C
Operating Humidity Range: 5 to 90% RH, non-condensing
STAGES
SOURCE 1 PART
APPLICATIONS
TERMINAL
SWITCH POSITIONS (SYSTEM)
DIMENSIONS
HEAT COOL MLP $
NO.
DESIGNATIONS
3-7/16”H X 4-1/2”W X 1-5/16”D (88MM H X
S1-TH5110D1022 24 VAC CONVENTIONAL & HEAT PUMP
R, RC, C,W (O/B), Y, G
HEAT-OFF COOL-AUTO
1
1
131.79
SYSTEMS;750 MV HEATING SYSTEMS
114MM W X 33MM D)
HEAT-OFF-COOL AUTO3-9/16”H X 5-13/16”W X 1-1/2”D (99MM H
S1-TH5220D1029 24 VAC CONVENTIONAL & HEAT PUMP RC, R, W (O/B),W2 (AUX),
2
2
182.43
Y,Y2 (E), G, L, C
EM.HEAT
X 147MM W X 38MM D)
HEAT-OFF-COOL AUTO3-9/16”H X 5-13/16”W X 1-1/2”D (99MM H
S1-TH5320U1001 24 VAC CONVENTIONAL & HEAT PUMP R, RC, W(O/B), W2(Aux/E),
2
2
196.11
Y, Y2, G, L, C
EM.HEAT
X 147MM W X 38MM D)
52
Thermostats
Digital Round Thermostat
Provides single-stage temperature control for 24V heating-cooling systems with manual changeover from heat to cool.
Features:
• Attractive styling complements any decor.
• Large easy-to-read display.
• Backlit display. On-demand backlighting makes it easy to read the display in a dark room or hallway.
• No batteries required.
• The temperature setting is held permanently in memory in the event of a power failure.
• Powered through heating-cooling system controls.
• System and Fan switches, Manual changeover from heat to cool.
• Easy installation, set up and 5-minute compressor bypass saves time and increases installer productivity.
• Easily configurable by the use of DIP switches, F or C temperature display.
• Selectable heating cycle rates (1, 3, 6, 9 cph) for a variety of applications.
• Cooling cycle rate is fixed at 3 cph. This is the standard compressor setting for quick installations.
• Minimum off-time for compressors in the cooling mode. Protects and extends the life of the equipment.
Specifications:
Mounting: Front wired
Changeov er: Manual
Color: Premier White
Power Method: Powered through heatingcooling system controls
Sw itch Type: Electronic
Accuracy (F): 0.5°C
Accuracy (C): 1°F
Dimensions (in.): 3-11/16” diameter x 1-7/16”D
Dimensions (mm): 94 mm diameter x 37 mm D
Setting Temperature Range (F): 40°F to 90°F in heating; 45°F to 99°F in cooling
Setting Temperature Range (C): 4.5°C to 32°C in heating; 7°C to 37°C in cooling
Cycles per Hour Adj.: 1,3,6,9
Ambient Temperature Range (F): 40°F to 110°F
Ambient Temperature Range (C): 4.5°C to 43.3°C
Humidity Ratings (%RH): 5 to 90% RH Includes Wallplate, 4074FAB resistor, mounting screws and wall anchors
STAGES
SWITCH POSITIONS
SOURCE 1 PART NO.
APPLICATIONS
HEAT
COOL
FAN
SYSTEM
MLP $
S1-T8775C1005
24 VAC GAS, OIL AND ELECTRIC HEATING
WITH COOLING,INCLUDING 1 HEAT/1
COOL HEAT PUMPS
1
1
R, RC, O, B, G, Y, W
AUTO-ON
OFF-HEAT-COOL
128.43
FocusPRO TH6110, TH6220 & TH6320 Thermostats
Features:
• Selectable 5+1+1 or 5/2 day programming.
• One-touch temperature control overrides program schedule at any time
• Built-in instructions
• Removable battery holder for fast, easy replacement
• Built-in compressor protection
Specifications:
Temperature Ranges: Heat 40°–90°F (4.5°– 32°C), Cool 50°–99°F (10°–37°C)
Operating Ambient Temperature: 32°–120°F (0°–48.9°C)
Operating Relative Humidity: 5%–90% (noncondensing)
Dimensions: 3-9/16”H x 5-13/16”W x 1-1/2”D (91mmH x 147mmW x 38mmD)
STAGES
SOURCE 1 PART NO.
APPLICATIONS
PROGRAM
HEAT
COOL
POWER SOURCE
MLP $
S1-TH6110D1021
24 VAC SINGLE-STAGE AND MULTI-STAGE
HEATING AND COOLING SYSTEMS,OR 750
MV HEATING SYSTEMS
MV HEATING SYSTEMS
MV HEATING SYSTEMS
5+1+1 or 5+2
1
1
182.96
5+1+1 or 5+2
2
2
226.32
5+1+1 or 5+2
3
2
249.64
S1-TH6220D1028
S1-TH6320U1000
53
Thermostats
Honeywell 2-Wire IAQ HD Color Touchscreen white front/white side thermostat with RedLINK™
technology
The Prestige® IAQ thermostat is a 2 wire high definition color touch screen thermostat, 7 day programmable and selectable for
residential or light commercial use. Controls up to 4-stages of heat and 2-stages of cool in a heat pump system and up to 3-stages of
heat and 2-stages of cool in a conventional system. Three sets of Universal IAQ contacts to control humidification, dehumidification,
and ventilation. Four sensor inputs for wired sensors or dry contact devices. Works with the Equipment Interface Module and
RedLINK® accessories including the RedLINK® Internet Gateway, Portable Comfort Control, Wireless Outdoor Sensor and Wireless
Indoor Sensor.
Features:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Control heating, cooling and IAQ equipment with only 2 wires at the thermostat. Heating, cooling and IAQ equipment wires to the
Equipment Interface Module.
Smart Schedule - programs in seconds for any lifestyle
Patented interview based programming and installer setup.
RedLINK™ wireless communication.
Increase profit per job by including RedLINK™ accessories that provide comfort and convenience. RedLINK™ accessories
include the RedLINK™ Internet Gateway, Portable Comfort Control (PCC), Wireless Outdoor Sensor, Wireless Indoor Sensor,
Wireless Entry/Exit Remote, Wireless Vent and Filter Boost Remote, TrueSTEAM™ humidifier with Wireless Adapter and
TrueZONE® zoning panel with Wireless Adapter.
Selectable for residential and light commercial applications. Meets commercial code and is title 24 compliant.
Light commercial - commercial language (occupied and unoccupied), schedule holidays and custom events, remote setback,
economizer and time of day.
Delta T Alerts and Diagnostics informs customers when their system is not performing as expected with instructions to contact
the dealer. Provides a sense of security and greater comfort while generating repeat business.
All Prestige® IAQ kits come standard with a return and discharge air temperature sensor to measure Delta T.
Alerts and User Interactions Log - Keeps a searchable history of alerts and setting changes to the thermostat to determine if
there is a system malfunction or if the issue was caused by user error. Saves time in troubleshooting and points the technician in
the right direction.
Performance Logs - Keeps a history of heating and cooling performance. The performance log includes Minimum and Maximum
Delta T, Minimum and Maximum Discharge Temperature, Minimum and Maximum Return Temperature, Minimum and Maximum
Indoor Temperature/Humidity, Minimum and Maximum Outdoor Temperature/Humidity and Run Time. Quickly determine if the
sy stem is performing as expected and reduces service time on the job.
Customizable Service Reminders allow dealers to remind their customers when its time to call for service, when their warranty is
expiring and to provide customized alerts.
USB port for transferring Installer Setup, Customizable Reminders, Custom Events and Holidays to multiple thermostats.
USB port for adding the dealer's full color business logo on the screen.
3 assignable outputs to control humidification, dehumidification, ventilation and a stage of heating or cooling.
4 assignable inputs on the Equipment Interface Module can be used with wired outdoor, indoor or discharge sensors, occupancy
sensor for remote setback and dry contact devices to trip pre-packaged or custom alerts such as a full drain pan or water leak.
Extend wireless range of the Equipment Interface Module by connecting a THM4000R1000 Wireless Adapter to the ABCD
terminals.
Tri-lingual - English, French and Spanish display options.
Precise temperature control (+/- 1° F) for reliable and consistent temperature.
Multiple staging options to provide comfort or energy savings
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-THX9421R5021WW
2-Wire IAQ High Definition Color Touchscreen
650.11
54
Thermostats
Honeywell C7772 Temperature Sensors
C7772 Temperature Sensors are designed for the Excel 5000 family and other Honeywell controllers. They provide a resistive output
signal and are well suited for low profile wall mounted applications.
Features:
•
•
•
•
•
Low profile when mounted on industry standard utility conduit box
Rugged, brushed stainless steel wallplate
Integral foam pad isolates wallplate sensor from conduit box
Insulated screw terminals ensure reliable field wiring connection
Models available with a variety of resistive temperature sensor elements
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-C7772A1004
20 K ohm NTC Flush Wall Mount Temperature Sensor
46.21
Honeywell Mount on return duct for backup control
Mount on return duct for backup control of non-zoned RedLINK™ enabled Wireless Systems and Thermostats.
Features:
• Works with THM5320R1000 Equipment Interface Module to maintain safe indoor temperatures if power is lost at the wireless
thermostat
• Takes control of the equipment by turning on the blower fan and sensing the indoor temperature of the home
• Controls heating at 62 F and cooling at 82 F
• Provides homeowners with peace of mind
• Includes mounting hardware
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-C7735A1000
Mount on return duct for backup control
101.71
Honeywell Premier White® Universal Programmable Thermostat
VisionPRO® 8000 has responsive programming for optimal comfort and energy savings. It offers you features like touch screen
interaction, a real-time clock, and a backlit display. If you value comfort, choose VisionPRO and enjoy it for years to come.
•
•
•
•
•
•
•
•
•
Hazmat Information - UN 3091 Lithium metal batteries packed in/with equipment
Application - Heat/Cool or Heat Pump with Auxiliary Heat
Dimensions (in.) - 4 9/16 in. high x 6 in. wide x 1 1/4 in. deep
Dimensions (mm) - 116 mm high x 152 mm wide x 32 mm deep
Comments - Includes a set of Universal IAQ contacts to control humidification, dehumidification or ventilation. Also has advanced
Dual Fuel control. Selectable Programmable or Non-Programmable. The L terminal is an input or an output.
Mounting – Horizontal
Electrical Ratings - 20 to 30 Vac or 750 mV
Frequency - 50 Hz; 60 Hz
Stages - Up to 3 Heat/2 Cool Heat Pump; Up to 2 Heat/2 Cool Conventional
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-TH8321U1097
Premier White® Universal Programmable Thermostat with 3 Heat / 2 Cool stages
463.21
55
Thermostats
Honeywell Prestige® 2.0 HD Color Touchscreen Thermostat, RedLINK™ enabled
Honeywell's Prestige redefines how a thermostat can look and function and is the easiest-to-use programmable thermostat available.
This RedLINK enabled line includes a: 7 Day Programming wizard, Multi-Language Options & USB setup, Customizable Service
Reminders.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Hazmat Information - UN 3091 Lithium metal batteries packed in/with equipment
Application - Up to 2 Heat/2 Cool Conventional Systems, Up to 3 Heat/2 Cool Heat Pumps
Dimensions (in.) - 3 15/16 in. High, 6 7/8 in. Wide, 1 1/2 in. Deep
Dimensions (mm) - 100 mm. High, 175 mm. Wide, 38 mm. Deep
Includes - Prestige 2.0 High Definition Color Touchscreen Thermostat
Used With - RedLINK™ enabled thermostats and accessories
Comments - Tri-Lingual Display (selectable for English, French or Spanish)
Electrical Ratings - 18 to 30 Vac
Frequency - 60 Hz,50 Hz
Stages - Up to 3 Heat / 2 Cool Heat Pump or Up to 2 Heat / 2 Cool Conventional
Electrical Connections - Screw terminals
Operating Humidity Range (% RH) - 0 to 90% RH, non-condensing
Supply Voltage - 18 to 30 Vac
Switch Positions (System) - HEAT-OFF-COOL-AUTO-EM.HEAT
Switch Positions (Fan) - AUTO-ON-CIRC
Operating Temperature Range (F) - 32 F to 120 F
Operating Temperature Range (C) - 0 C to 48.9 C
Color - Arctic White
Programmability - 7-Day Multiple Day Programming or Non-Programmable
Power Method – Hardwired
Terminal Designations - R, RC, C, W-O/B, W2-AUX/E, Y, Y2, G, A-L/A, K, U1 U1, U2 U2
Display Size - 8.06 sq in.
Changeover - Auto or Manual
Setting Temperature Range (F) - Heat: 40 F to 90 F; Cool 60 F to 99F
Setting Temperature Range (C) - Heat: 4.5 C to 32.0 C; Cool: 15.5 C to 37.0 C
Humidification Setting Range - Cooling: 40 to 80% RH. Heating: 10 to 60% RH.
Dehumidification Setting Range - 40 to 80% RH.
External Sensors Available - Outdoor -- Yes, optional
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-THX9321R5030
Honeywell Prestige® 2.0 HD
711.07
Honeywell R8182D Protectorelay® and Hydronic Heating Controllers
Immersion type Aquastat controller and oil burner primary control provides high limit and low limit/circulator control for oil-fired
hydronic heating systems.
Features:
• Use in intermittent ignition applications.
• Capable of zone control with zone valves.
• Circulator zone control with ZC and ZR terminals on R8182D,E,H,J. 8*Flame failure during the running cycle results in a 45 second
attempt to restart.
• If unsuccessful, safety shutoff occurs, requiring manual reset before burner can be restarted.
• R8182D,E,F mount directly on burner; R8182H,J mount on 4 x 4 in. junction box and include 5 ft (1.5 m) armored capillary with
remote sensor.
• C554A Cadmium Sulfide Flame Detector and a 24 Vac thermostat required.
SOURCE 1 PART NO.
DIFFERENTIAL
MOUNTING
MLP $
S1-R8182D1079
S1-R8182D1111
HI LIMIT 10F FIXED, LO LIMIT 10F-25F ADJUSTABLE
HI LIMIT 10F FIXED, LO LIMIT 10F-25F ADJUSTABLE
VERTICAL
HORIZONTAL
990.21
864.93
Honeywell RedLINK Wireless Entry/Exit Remote
Hazmat Information:
Application:
Dimensions (in.):
Used With:
Operating Humidity Range (% RH):
Operating Temperature Range (F):
Operating Temperature Range (C):
Sensor Element:
Color:
Power Method:
UN 3091 Lithium metal batteries packed in/with equipment
Heating and Cooling systems,RedLINK Thermostat Accessory
6 1/4 in. high x 3 1/8 in. wide x 1 5/8 in. deep
RedLINK™ enabled thermostats and accessories
5 to 90% RH, non-condensing
35 F to 114 F for optimal battery life
1.7 C to 45.6 C for optimal battery life
Thermistor
White
Battery, Lithium Coin Cell
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-REM1000R1003
RedLINK Wireless Entry/Exit Remote
77.18
56
Thermostats
Honeywell REM5000R Portable Comfort Control
Use the Portable Comfort Control anywhere in the home to experience a new level of comfort and convenience. Works in both zoned
and non-zoned applications.
Features:
• Works with compatible RedLINK™ enabled thermostats and accessories
• Touchscreen interface with backlit display
• Can display outdoor temperature and humidity
• Built-in pager with an audible noise helps locate the device in the home
• Screen-lock feature helps prevent accidental changes
• 1 year battery life
• 2 month low battery warning In Non-Zoned Applications:
• Bring it with you anywhere in the home to sense and control temperature from the room that you are in. In Zoned Applications:
• View and adjust all RedLINK™ enabled thermostats from a single control.
• Controls up to 16 thermostats
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-REM5000R1001
PORTABLE COMFORT CONTROL FOR REDLINK TSTATS
231.57
57
Thermostats
Honeywell VisionPRO® 8000 with RedLINK™ technology for residential or commercial use
VisionPRO® 8000 with RedLINK™ is a 7 day programmable touchscreen thermostat that is selectable for residential or light
commercial use. The thermostat can be wired directly to the equipment, used with the THM5421R1021 Equipment Interface Module
or used with the THM4000R1000 TrueZONE Wireless Adapter. Works with the RedLINK™ accessories including the RedLINK™
Internet Gateway, Portable Comfort Control, Wireless Outdoor Sensor, Wireless Indoor Sensor, Wireless Entry/Exit Remote and
Wireless Vent and Filter Boost Remote.
Features:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Thermostat works standalone or with the THM5421R1021 Equipment Interface Module or with the TrueZONE Wireless Adapter.
Smart Schedule - programs in seconds for any lifestyle.
Increase profit per job by including RedLINK™ accessories that provide comfort and convenience. RedLINK™ accessories include
the RedLINK™ Internet Gateway, Portable Comfort Control (PCC), Wireless Outdoor Sensor, Wireless Indoor Sensor, Wireless
Entry/Exit Remote, Wireless Vent and Filter Boost Remote, TrueSTEAM™ humidifier with Wireless Adapter and TrueZONE®
zoning panel with Wireless Adapter.
economizer and time of day. Remote Setback requires the THM5421R1021 Equipment Interface Module.
Plain language setup, no manual needed.
Alerts and User Interactions Log - Keeps a searchable history of alerts and setting changes to the thermostat to determine if there
is a system malfunction or if the issue was caused by a user error. Saves time in troubleshooting and points the technician in the
right direction. The Alert and User Interaction Logs are viewable on a computer after you download them from the thermostat to a
microSD card.
MicroSD port for copying the Installer Setup, Customizable Reminders, Custom Events and Holidays to multiple thermostats.
MicroSD port for adding the dealer's contact information on the screen.
1 assignable output on the TH8321 model to control humidification, dehumidification, ventilation or a stage of heating/cooling.
3 assignable outputs on the Equipment Interface Module to control humidification, dehumidification, ventilation or a stage of
heating/cooling. The TH8110 and TH8320 models require the use of a Wireless Indoor Sensor to control humidification and
dehumidification.
1 assignable input can be used with a wired outdoor, indoor or discharge sensor.
terminals.
Dual powered - battery or hardwired (C wire).
Multiple staging options to provide comfort or energy savings.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-TH8110R1008
S1-TH8320R1003
S1-TH8321R1001
VisionPRO® 8000 with RedLINK - Stages up to 1 Heat / 1 Cool
402.25
446.93
487.57
58
Thermostats
Honeywell Wi-Fi FocusPRO® 6000
Honeywell's Wi-Fi FocusPRO® 6000 allows remote access to the thermostat through a computer, tablet, or smart phone with
Honeywell's Total Connect Comfort Service
Features:
•
•
•
•
•
•
•
•
•
•
Homeowners can monitor and control their home's comfort settings from anywhere at anytime
Connect using a regular computer, tablet or smartphone
Automatic software updates through Wi-Fi
Selectable to 7-Day or Non-programmable thermostat
Large, clear, backlit display - easy to read in various lighting conditions
Precise comfort control (±1 F) - maintains consistent comfort to the highest level of accuracy
Simplified programming and operation
Built in instructions - simple, pull out instruction manual
Adaptive Intelligent Recovery™ - ensures programmed temperature is reached by programmed time
Temperature range stops - prevents user from setting the temperature too high or too low
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-TH6320WF1005
Honeywell Wi-Fi FocusPRO® 6000
308.82
59
Thermostats
Honeywell WiFi VisionPRO Thermostat, Heat/Cool or Heat Pump with Auxiliary Heat
The Prestige® IAQ thermostat is a 2 wire high definition color touch screen thermostat, 7 day programmable and selectable for
residential or light commercial use. Controls up to 4-stages of heat and 2-stages of cool in a heat pump system and up to 3-stages of
heat and 2-stages of cool in a conventional system. Three sets of Universal IAQ contacts to control humidification, dehumidification,
and ventilation. Four sensor inputs for wired sensors or dry contact devices. Works with the Equipment Interface Module and
RedLINK® accessories including the RedLINK® Internet Gateway, Portable Comfort Control, Wireless Outdoor Sensor and Wireless
Indoor Sensor.
Features:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Control heating, cooling and IAQ equipment with only 2 wires at the thermostat. Heating, cooling and IAQ equipment wires to the
Equipment Interface Module.
Smart Schedule - programs in seconds for any lifestyle
Increase profit per job by including RedLINK™ accessories that provide comfort and convenience. RedLINK™ accessories
include the RedLINK™ Internet Gateway, Portable Comfort Control (PCC), Wireless Outdoor Sensor, Wireless Indoor Sensor,
Wireless Entry/Exit Remote, Wireless Vent and Filter Boost Remote, TrueSTEAM™ humidifier with Wireless Adapter and
TrueZONE® zoning panel with Wireless Adapter.
economizer and time of day.
Delta T Alerts and Diagnostics informs customers when their system is not performing as expected with instructions to contact
the dealer. Provides a sense of security and greater comfort while generating repeat business.
All Prestige® IAQ kits come standard with a return and discharge air temperature sensor to measure Delta T.
Alerts and User Interactions Log - Keeps a searchable history of alerts and setting changes to the thermostat to determine if
there is a system malfunction or if the issue was caused by user error. Saves time in troubleshooting and points the technician in
the right direction.
Performance Logs - Keeps a history of heating and cooling performance. The performance log includes Minimum and Maximum
Delta T, Minimum and Maximum Discharge Temperature, Minimum and Maximum Return Temperature, Minimum and Maximum
Indoor Temperature/Humidity, Minimum and Maximum Outdoor Temperature/Humidity and Run Time. Quickly determine if the
sy stem is performing as expected and reduces service time on the job.
USB port for transferring Installer Setup, Customizable Reminders, Custom Events and Holidays to multiple thermostats.
USB port for adding the dealer's full color business logo on the screen.
3 assignable outputs to control humidification, dehumidification, ventilation and a stage of heating or cooling.
terminals.
Tri-lingual - English, French and Spanish display options.
Multiple staging options to provide comfort or energy savings
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-TH8320WF1029
WiFi VisionPRO Thermostat
446.93
60
Thermostats
Honeywell Wireless FocusPro® System Kits
Everything you need to relocate thermostat or upgrade equipment without running new wires!
Features:
• Same great features of the FocusPRO thermostats—now wireless
• Can display outdoor temperature and humidity
• 1-year battery life; 2-month low battery warning
SOURCE 1 PART NO.
DESCRIPTION
INCLUDES
MLP $
S1-YTH5320R1000
WIRELESS THERMOSTAT
KIT-NON-PROGRAMMABLE
WIRELESS ZONING ADAPTER
KIT-NON-PROGRAMMABLE
WIRELESS THERMOSTAT KIT-5-1-1
PROGRAMMABLE
WIRELESS SYSTEM KIT-5-1-1 PROGRAMMABLE
TH5320R1002 WIRELESS FOCUSPRO THERMOSTAT, THM5320R1000
EQUIPMENT INTERFACE MODULE, AND C7735A1000 RETURN AIR SENSOR
THM4000R1000 WIRELESS ADAPTER, TH5320R1002 WIRELESS FOCUSPRO
THERMOSTAT
TH6320R1004 WIRELESS FOCUSPRO THERMOSTAT, THM5320R1000
EQUIPMENT INTERFACE MODULE, AND C7735A1000 RETURN AIR SENSOR
REM5000R1001 PERSONAL COMFORT STATION, TH6320R1004 WIRELESS
FOCUSPRO THERMOSTAT, C7089R1013 WIRELESS OUTDOOR SENSOR,
THM5320R1000 EQUIPMENT INTERFACE MODULE, AND C7735A1000 RETURN
AIR SENSOR
THM4000R1000 WIRELESS ADAPTER, TH6320R1004 WIRELESS FOCUSPRO
THERMOSTAT
564.07
S1-YTH5320R1025
S1-YTH6320R1001
S1-YTH6320R1015
WIRELESS ZONING ADAPTER KIT-5-1-1
PROGRAMMABLE
S1-YTH6320R1023
372.14
607.25
889.00
413.46
TH6320R1004 FocusPRO® Wireless Programmable Thermostat
The FocusPRO™ programmable thermostat provides electronic control of 24 Vac conventional and heat pump systems or 750 mV
heating systems.
Features:
• Selectable to 5-1-1 (Weekdays, Saturday, Sunday) or 5-2 (Weekdays, Weekend) programmable thermostat.
• Large, clear, backlit display - easy to read in various lighting conditions.
• Display size options - available in large screen or standard.
• Precise comfort control (+/-1 F) - maintains consistent comfort to the highest level of accuracy.
• Simplified programming and operation.
• Easy change battery door - flip out door allows for easy battery replacement without removing or disassembling the thermostat.
• Built in instructions - simple, pull out instruction manual.
• Adaptive Intelligent Recovery™ - ensures programmed temperature is reached by programmed time.
• Temperature range stops - prevents user from setting the temperature too high or too low.
• Application - Gas, oil, electric, heat pump, forced warm air, hot water, steam or gravity
• Dimensions (in.) 3 9/16 in. High X 5 13/16 in. Wide X 1 1/2 in. Deep
• Thermostat is also available in kits for zoned and non-zoned systems
• Stages - Up to 3 Heat / 2 Cool Heat Pump or Up to 2 Heat / 2 Cool Conventional
• Operating Humidity Range (% RH) 5 to 90% RH, non-condensing
• Switch Positions (System) - HEAT-OFF-COOL-AUTO-EM.HEAT
• Switch Positions (Fan) - AUTO-ON
• Operating Temperature Range (F) - 32 F to 120 F
• Sensor Element - Thermistor
• Differential Temperature (F) - ± 1 F
• Differential Temperature © - ±0.5 C
• Programmability - 5-1-1 Day Program or 5-2 Day Program
• Power Method - Battery
• Changeover - Auto/Manual Selectable
• Setting Temperature Range (F) - Heat: 40 F to 90 F; Cool: 50 F to 99 F
• Parts Needed for Operation (not included) - TrueZONE™ System - HZ432 or HZ322 TrueZONE™ panel; THM4000R1000 Wireless
Adapter
• Parts Needed for Operation (not included) - Non-Zoned System - THM5320R1000 Equipment Interface Module
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-TH6320R1004
WIRELESS PROGRAMMABLE THERMOSTAT
380.32
61
Thermostats
TH3000 Series Digital Thermostats
Honeywell’s PRO 3000 Series offers a basic, non-programmable thermostat with the convenience of an easy-to-read digital display.
STAGES
SOURCE 1 PART NO.
APPLICATIONS
POWER SOURCE
HEAT
COOL
MLP $
S1-TH3110D1008
24 VAC SINGLE-STAGE
HEATING AND COOLING
SYSTEMS OR 750MV HEATING
SYSTEM
24 VAC HEAT PUMP SYSTEMS
WITH AUXILIARY HEAT
R, RC, C, W, Y. G, O, B
2
1
86.00
R, C, Y, AUX, E, G, O, B, L
1
1
119.96
S1-TH3210D1004
TH4000 Series Digital Thermostats
Features:
• Separately programmable weekday/weekend schedules
• One-touch temperature control overrides program schedule at any time
• Built-in compressor protection
Specifications:
Temperature Ranges: Heat 40°–90°F (4.5°– 32°C), Cool 50°–99°F (10°–37°C)
Operating Ambient Temperature: 32°–120°F (0°–48.9°C)
Operating Relative Humidity: 5%–90% (noncondensing)
Dimensions: 3-13/16”H x 5-3/8”W x 1-1/4”D (97mmH x 137mmW x 32mmD)
Electrical Ratings: 20–30 VAC, 0.02–1.0 A running current
STAGES
SOURCE 1 PART NO.
APPLICATIONS
TERMINAL
DESIGNATIONS
R, RC, C, W, Y, G, O, B
POWER SOURCE
PROGRAM HEAT COOL
24 VAC SINGLE-STAGE HEATING AND
COOLING SYSTEMS,OR 750 MV HEATING
SYSTEMS.
24 VAC HEAT PUMP SYSTEMS WITH AUXILIARY R, C, Y, Aux, E, G, O, B, L HARDWIRED OR BATTERY
HEAT (2 HEAT/1 COOL)
S1-TH4110D1007
S1-TH4210D1005
MLP $
5+2
1
1
103.11
5+2
2
1
134.54
HONEYWELL MECHANICAL THERMOSTATS
The Round Mercury-Free Thermostat
This thermostat features a precision electronic switch that completely eliminates the need for mercury, for environmentally-friendly
performance. Precision, accuracy and reliability continue to be hallmarks of this popular, classic design
STAGES
SOURCE 1 PART NO.
DESCRIPTION
HEAT
COOL
MLP $
S1-T87K1007
S1-T87N1000
THE ROUND® MERCURY-FREE THERMOSTAT
THE ROUND® MERCURY-FREE THERMOSTAT
1
1
0
1
80.32
117.54
62
Thermostats
T7350 Commercial Programmable Thermostat
For Single- or Multi-Stage Conventional/Heat Pump Systems
The T7350 controls 24 VAC commercial single zone heating, ventilating and air conditioning equipment. The T7350 consists of a
thermostat and subbase. The thermostat includes the keypad and display for 7-day programming. The subbase includes equipment
control connections.
Features:
• Typically used in buildings under 55,000 square feet.
• For single zone rooftop units, split systems, heat pumps or hot/chilled water systems.
• 7-day programming includes 2 Occupied and 2 Not Occupied periods per day.
• Individual heat and cool setpoints available for Occupied and Not Occupied periods.
• Recovery ramp control automatically optimizes equipment start times based on building load.
• Convenient overrides allow temporary setpoint changes.
• Keypad multi-level lockout available with all models.
• The thermostat maintains programmed times and temperatures for the life of the product. Clock and day information is retained for
a minimum of 48 hours in the event of a power outage.
Specifications:
Electrical Power: 24 VAC, 50/60 Hz; 20–30 VAC, 50/60 Hz
Setpoint Ranges:
Heating: 40°–90°F (4°–32°C)
Operating Humidity: 5%–90% RH, noncondensing
Cooling: 45°–99°F (7°–37°C)
Operating Ambient Temperatures: 30°– 110°F (-1°–43°C)
Display Accuracy: ±1°F (±1°C)
MAXIMUM STAGES*
SOURCE 1 PART NO.
APPLICATIONS
HEAT
COOL
FEATURES
AUXILIARY RELAY
MLP $
S1-T7350B1002
CONVENTIONAL OR HEAT
PUMP
CONVENTIONAL OR HEAT
PUMP
2†
2†
YES
542.25
3 (2) **
3 (4) **
OUTDOOR, DISCHARGE AIR
CAPABILITY
HUMIDITY, OCCUPANCY,
OUTDOOR,
DISCHARGE AIR CAPABILITY
ISOLATED NORMALLY
OPEN
912.00
S1-T7350H1009
* All models are down-selectable; can be configured to control fewer stages than the maximum allowed.
† One extra stage (of either heat or cool) can be configured using the auxiliary relay.
** Heat pump applications for this model have a maximum of 2 heat stages and 2 cool stages.
VisionPRO® Commercial Programmable Thermostat
®
The TB8220 Commercial Vision Pro 8000 Touchscreen Programmable Thermostat is an effortless, seven-day programmable
thermostat that provides universal system compatibility, precise comfort control and is easy to program.
The TB8220 provides temperature control for gas, oil, electric and heat pumps for up to 2 heat, 2 cool systems.
Features:
• Large, clear display with backlight shows the current and set temperature and time—even in the dark
• Menu-driven programming makes setup effortless
• Beautiful ergonomic design is smart and sophisticated to match your customers’ lifestyles
• Touchscreen interaction
• Real-time clock keeps time during power failures and automatically updates to daylight savings
• “Saving Changes” notification lets you know when the schedule changes have been saved
• Change reminders let you know when to replace the batteries
• Holiday Override options allow you to override the program schedule, as desired
• Speedy same-schedule programming—no need to copy multiple days
• Armchair programming allows you to remove the thermostat from the wall for programming
Specifications:
Electrical Ratings:
Voltage: 20–30 VAC at 50/60 Hz;
Running Current: 0.02–1.0A (Fan 0.02– 0.60A)
Temperature Setting Ranges:
Heating: 40°–90°F (4°–32°C)
Cooling: 50°–99°F (10°–37°C)
Humidity Ratings: 5%–90% RH non-condensing
SOURCE 1 PART NO.
DESCRIPTION
APPLICATION
S1-TB8220U1003
COMMERCIAL VISION PRO® 8000
GAS OR ELECTRIC HEAT WITH AIR CONDITIONING
WARM AIR, HOT WATER, HIGH-EFFICIENCY FURNACES,
AND HEAT PUMPS HEAT ONLY HEAT ONLY WITH FAN
COOL ONLY
63
TERMINAL
DESIGNATIONS
R, RC, W(O/B), W2(W1), Y,
Y2, L, A, G, C, S1, S2
STAGES
MLP $
2H/2C (CONV)
3H/2C
(HEATPUMP)
506.21
Thermostats
L4006A1678 Aquastat Controller
High or Low Limit
Ov erview
Aquastat® Controllers are immersion type devices for limiting or regulating the temperature of liquids in boilers, storage tanks, and
other applications where temperature control is required.
Features:
• Totally enclosed Micro Switch™ snap-acting switches operate on temperature rise to setpoint.
• Visible control point scale and external adjustment screw permit easy setting.
• Horizontal or vertical insertion of the sensing element.
• Direct or well immersion of the sensing element.
• Models available for strap-on mounting.
• Remote bulb model may be used to sense air temperature in ducts and in outside air sensing applications.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-L4006A1678
HIGH OR LOW LIMIT AQUASTAT CONTROLLER
230.64
L4064B Fan/Limit Controllers
For control of high limit and fan motor in all types of forced air heating systems.
Features:
• Three wiring terminal options available for easy installation:
• Push-in receptacles for stripped wire.
• Female receptacles for 1/4 in. male flag connectors.
• Field add-on screw terminals.
• Controls adapt to many competitive mounting holes in replacement applications.
• Available in a variety of fan and high limit setting ranges.
• Manual fan switch overrides fan control to keep fan running continuously.
• Mounting adapters for easy installation and strain relief bushings to protect wiring from field abuse.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-L4064B2210
S1-L4064B2228
FAN/LIMIT CONTROLLER
FAN/LIMIT CONTROLLER W/ 5" INSERTION
208.68
208.68
L6006C1018 High/Low Limit Aquastat Controller for Residential Combustion
Aquastat® Controllers are immersion type devices for limiting or regulating the temperature of liquids in boilers, storage tanks, and
other applications where temperature control is required.
Features:
• Horizontal or vertical insertion of the sensing element.
• Direct or well immersion of the sensing element.
• TRADELINE models include heat-conductive compound.
• Select models have wells.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-L6006C1018
HIGH/LOW LIMIT AQUASTAT CONTROLLER
203.61
L7224U1002 Aquastat Controller for Oil
120 Vac oil electronic Aquastat Controller with EnviraCOM ™ com munication
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-L7224U1002
120 VAC OIL ELECTRONIC AQUASTAT CONTROLLER
359.96
64
Thermostats
L8124 Triple Aquastat Relay
Immersion-type controllers that combine high limit protection with low limit and circulator control in forced hydronic heating systems,
including domestic hot water service.
Features:
• Immersion-type controllers that combine high limit protection with low limit and circulator control in forced hydronic heating systems.
• Provide multizone control by using a separate circulator and R845 Relay for each zone.
• Include diaphragm powerhead and Micro Switch™ assembly that respond to temperature changes in boiler water.
• Mount directly to boiler.
• Select models include large transformers and extra terminals for supplying power to low voltage zone valves.
• Require 24 Vac thermostat with heat anticipator set at 0.2 A (plus current draw of gas valve on L8124E).
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-L8124A1015
S1-L8124C1003
S1-L8124E1016
TRIPLE AQUASTAT RELAY
350.21
463.89
477.25
L8148E1265 High limit Aquastat Relay, 15 F Fixed Differential
Immersion-type controller that combines high limit protection with switching relay control of burner and circulator motors.
Features:
• High limit opens burner circuit only.
• Include transformer and accessory terminals for adding a remote low limit controller.
• Case available for horizontal or vertical mounting.
• Requires a 24 Vac thermostat with heat anticipator set at 0.2A.
• TRADELINE models include well adapter, tube of heat conductive compound and range stops.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-L8148E1265
HIGH LIMIT AQUASTAT RELAY
394.18
65
Thermostats
BEKO THERMOSTAT GUARDS
Classic Series
Medium Size
Inside Dimensions
BASE TYPE
SOLID
RING
HEIGHT
4-3/8”
4-5/8”
WIDTH
5-1/4”
5-1/4”
DEPTH
3"
3-14"
SOURCE 1 PART NO.
DESCRIPTION
CTN. QTY.
MLP $
S1-BTGB
S1-BTGK
S1-BTGKM
S1-BTGKWM
S1-BTGO
BRONZE PLASTIC (2 BASES)
CLEAR PLASTIC DUAL (2 BASES)
BEIGE METAL, SOLID BASE
BEIGE METAL, RING BASE
OPAQUE PLASTIC (2 BASES)
12
12
12
12
12
22.39
15.29
39.57
37.57
29.50
*M LP Per Each
Designer Series
Low Profile Style
Inside Dimensions
BASE TYPE
DUAL SOLID
DUAL RING
HEIGHT
4-1/4”
4-1/8”
WIDTH
7-5/8”
7-1/16
DEPTH
2-1/8"
2-1/4"
SOURCE 1 PART NO.
DESCRIPTION
CTN. QTY.
MLP $
S1-BTGDB
S1-BTGDK
S1-BTGDK1
S1-BTGDK2
CLEAR PLASTIC (2 BASES)
CLEAR PLASTIC (2 BASES) WITH OVAL/ROUND HOLES
CLEAR PLASTIC (2 BASES) WITH OVAL/ROUND HOLES, FOR CS90
12
12
12
12
40.25
24.50
28.25
26.82
SOURCE 1 PART NO.
DESCRIPTION
CTN. QTY.
MLP $
S1-BTGEB
S1-BTGEK
S1-BTGEO
BRONZE PLASTIC (SOLID BASE)
CLEAR PLASTIC (SOLID BASE)
OPAQUE PLASTIC (SOLID BASE)
12
12
23.71
15.68
16.50
*M LP Per Each
Elite Series
*M LP Per Each
Regal Series
IDEAL FOR HORIZONTAL AND VERTICAL STANDARD SIZE WALL THERMOSTATS
Inside Dimensions
BASE T YPE
SOLID
RING
HEIGHT
6-3/8”
6-3/8”
WIDTH
3-1/2”
3-1/2”
DEPT H
3"
3-1/4"
SOURCE 1 PART NO.
DESCRIPTION
CTN. QTY.
MLP $
S1-BTGRB
S1-BTGRK
S1-BTGRM
S1-BTGRO
BEIGE METAL, SOLID
12
12
12
12
22.36
18.86
37.57
21.46
S1-BTGRWM
BEIGE METAL, RING
12
39.57
*M LP Per Each
66
Thermostats
BEKO THERMOSTAT GUARDS
Sentinal Series
THIS STRONG THERMOSTAT GUARD, CAN BE MOUNTED HORIZONTAL OR VERTICAL AND IS
COMPLETELY TAMPER PROOF.
Inside Dimensions
.
BASE TYPE
SOLID
RING
HEIGHT
6-1/4”
6”
WIDTH
4-3/4”
3-13/16”
DEPTH
3"
3-1/8"
SOURCE 1 PART NO.
DESCRIPTION
CTN. QTY.
MLP $
S1-BTG54VL
S1-BTG54VLW
BEIGE METAL, SOLID
BEIGE METAL, RING
12
12
39.61
33.93
*M LP Per Each
Universal Series
Plastic Inside Dimensions
BASE TYPE
HEIGHT
SOLID
8-1/4”
RING
8-1/8”
WIDTH
5-3/8”
4-5/8”
DEPTH
3-1/2"
3-5/8"
WIDTH
5-3/8”
4-1/4”
DEPTH
3-1/2"
3-9/16"
Metal Inside Dimensions
BASE TYPE
SOLID
RING
HEIGHT
7-1/4”
6-3/4”
SOURCE 1 PART NO.
DESCRIPTION
CTN. QTY.
MLP $
S1-BTGUB2
S1-BTGUK2
S1-BTGUM
S1-BTGUM2
S1-BTGUO2
S1-BTGUWM
S1-BTGUWM1DOWR
BEIGE METAL, SOLID
WHITE METAL, COMBO BASE
BEIGE METAL, RING
WHITE METAL, RING BASE WITH OVAL/ROUND DISP. HOLE, FOR 1F90
12
12
12
12
12
12
12
22.36
15.68
71.11
42.39
23.25
71.11
40.25
*M LP Per Each
ICM Temporary Construction Thermostats
The SC045 to SC075 series thermostats are low-cost, single setpoint thermostats intended for use as temporary devices to provide
heating or cooling to allow drywall to dry during construction. They also can be used as a low ambient cutoff switc
Features:
• Two-wire installation
• Six fixed setpoint models to choose from: 45oF to 75oF
• Temporary use for dryout applications
• Can be used as a low ambient cutoff switch
Specifications:
Input: 18-30 VAC
Output: 2 amp maximum
Temperature Control Range: 45°F to 75°F (±5°F)
Mode Of Operation
Heat/Cool Thermostat- The heating models will close when the ambient temperature drops below the respective setpoint and open
when the ambient temperature is above the respective setpoint. The cooling models will close when the ambient temperature is above
the respective setpoint and open when the ambient temperature drops below the respective setpoint.
Low Ambient Cutoff: Condenser Fan Motor- The SC045 and SC055 models can be used as a low ambient cutoff switch for a
condensor fan motor. When the ambient temperature drops below the setpoint, the unit will open the fan signal and turn the fan motor
off. It will not allow the fan to turn back on until the temperature rises above the setpoint.
Low Ambient Cutoff: Compressor- The SC045 and SC055 models can also be used as a low ambient cutoff switch for the
compressor when wired in series with the Y circuit from the thermostat. When using with the compressor circuit, an anti-short cycle
timer is recommended to prevent possible damage to the compressor from short cycling.
SOURCE 1 PART NO.
TEMPERATURE RANGE*
2-WIRE
HEAT
COOL
MLP $
S1-SC045
S1-SC055
S1-SC060
S1-SC065
S1-SC070
S1-SC075
45°F ±5°
55°F ±5°
60°F ±5°
65°F ±5°
70°F ±5°
75°F ±5°
YES
YES
YES
YES
YES
YES
NO
NO
YES
YES
YES
NO
YES
YES
NO
NO
NO
YES
19.89
19.89
19.96
19.96
19.96
19.89
67
Thermostats
ICM Temporary Construction Thermostats
* Consul t factory for other set points
SIGHT GLASSES & MOISTURE INDICATORS
Source 1 Sight Glasses
Sight glass and moisture indicator provides a quick visual indication of refrigerant and moisture levels within a system. The sight glass
indicates if the system has the proper refrigerant level, a restricted dryer, or excessive pressure- drop. The moisture indicator
recognizes moisture within the system, which may indicate a problem that could result in corrosion, chemical damage, restricted flow,
or even compressor failure. Etch-resistant glass with a simple color comparison provides easy viewing and quick diagnostics. Sweat
models feature copper fittings to permit solder installation without disassembly. Leak-proof design is compact and short in length to
easily fit within a unit.
SOURCE 1 PART NO.
CONNECTIONS (INCHES)
MLP $
S1-SG-3S
S1-SG-4S
SWEAT 3/8
SWEAT 1/2
21.00
27.68
FILTERS
Sporlan See-All Moisture and Liquid Indicator
Features:
• Extremely accurate
• Full view sight glass
• Indicator protected by filter pad and screen
• Replaceable indicator element
SOURCE 1 PART NO.
SPORLAN PART NO.
DWG. NO.
CONNECTION SIZE AND TYPE
S1-700026
S1-700052
S1-700078
S1-700091
S1-700130
S1-700260
S1-700299
S1-700416
S1-700507
S1-700546
SA-12FM
SA-12S
SA-13
SA-13FM
SA-13S
SA-14FM
SA-14S
SA-15S
SA-17S
SA-19S
SA-1
SA-2
1/4 SAE M X 1/4 SAE F
1/4 ODF
3/8 SAE
3/8 ODF
1/2 ODF
5/8 ODF
7/8 ODF
1-1/8 ODF
SEE- ALL
SHOWS
Green DRY
Chartreuse CAUTION
Y ellow WET
R-22
25°C
BELOW 30
30–90
ABOVE 90
40°C
BELOW 45
45–130
ABOVE 130
SA-1
SA-2
SA-1
SA-2
SA-2
SA-2
SA-2
MOIS TURE CONTENT PP M
R-134a
R-404 A & R-507
LIQUID LINE TEMP
25°C
40°C
25°C
40°C
BELOW 50
BELOW 80
BELOW 15
BELOW 30
50–200
15–90
80–225
30–140
ABOVE 200
ABOVE 225
ABOVE 90
ABOVE 140
OVERALL
LENGTH
2.56
4.62
3.37
2.97
4.62
3.44
4.87
4.87
6.31
6.31
SHIPPING
WT. (LBS.)
.50
.50
.50
.50
.63
1.00
1.00
1.50
1.50
R-407C
25°C
BELOW 120
120–280
ABOVE 280
MLP $
37.07
37.07
37.86
37.86
37.86
45.32
45.32
46.93
69.29
74.89
R-410 A
25°C
BELOW 75
75–150
ABOVE 150
NOTE: Change or add Catch-All Filter-Drier when paper turns from green to chartreuse.
Bold figures are for the average design conditions of refrigerant liquid lines operating at 100°F. Since the actual temperature is not critical, a
satisfactory estimate can be made by comparing it to body temperature. If it feels cool to the touch, use 75°F; if it feels warm, use 125°F column figures.
68
DRIERS
Source 1 Liquid Line Filter Driers (Solid Core)
Features:
• Solid Core Design for increased service life
• XH-11 molecular sieve with activated Alumina
• Compatible with all refrigerants, including 134a, 401 A/B, 402 A/B, 404A, 407 A/B/C, 410A, 502, 507A
• Solid copper sweat connection fittings, Steel tube body
• Drier meets ANSI 63.1-1995
• Desiccant meets ANSI 35-1992
• Max Working Pressure = 680 psi, Min Burst Pressure = 3400 psi
• Powder Coat meets 500hr salt spray
• UL Listed
SOURCE 1 PART NO.
TYPE
ODF
CU IN
MLP $
S1-SLFD053S
S1-SLFD083S
S1-SLFD163S
S1-SLFD164S
S1-SLFD305S
LIQUID
LIQUID
LIQUID
LIQUID
LIQUID
3/8
3/8
3/8
1/2
5/8
5
8
16
16
30
21.25
23.21
24.11
24.82
42.68
Source 1 Liquid Line Filter-Driers
Features:
• High moisture and acid capacity
• Maximum filtration capacity
• Exceptional compatibility with new polyester oils
• Compatible with all existing and new refrigerants and blends including 134a, 401A/B, 402A/B, 404A, 407A/B/C, 410A, 502, and
507A
• Spring-loaded, molecular sieve and activated alumina, Solid copper sweat fittings
• Corrosion-resistant powder coated exterior surpasses 500-hr ASTM salt spray test
Specifications:
Maximum w orking pressure: 680 psi*
*Note: Above pressure rating is valid for Source 1 driers manufactured after June, 2009. These driers can be identified by the UL mark
on the box and drier label.
SOURCE 1 PART NO.
TYPE
ODF
CU IN.
MLP $
S1-LFD083S
S1-LFD163S
LIQUID
LIQUID
3/8
3/8
8
16
18.86
19.57
69
DRIERS
Sporlan Catch-All Liquid Line Filter-Driers
Features:
• Leakproof shell
• Solid copper sweat fittings
• Outlet safety filter
• A blend of desiccants for maximum moisture removal
• Lower end point dryness levels, Maximum working pressure: 650 psi
• Compatible with refrigerants 12, 22, 134a, 404A, 407C, 410A, 502, 507
DIMENSIONS
SOURCE 1 PART NO.
SPORLAN MODEL
NO.
S1-400000
C-032
S1-400001
S1-400016
S1-400032
S1-400052
S1-400072
S1-400200
S1-400210
S1-400249
S1-400288
S1-400329
S1-400416
S1-400429
S1-400435
S1-400437
S1-400472
S1-400503
S1-400536
S1-401000
S1-401018
S1-401021
S1-401022
S1-401023
S1-401025
S1-401031
S1-401035
S1-401048
S1-401080
S1-401128
S1-401216
S1-401305
S1-401307
S1-401313
S1-401317
S1-401360
S1-401408
S1-401449
S1-401505
S1-401609
S1-401610
S1-401618
S1-401656
S1-401865
S1-52636217000
C-033S
C-032-F
C-032-FM
C-032S
C-032-CAPT
C-052
C-0525S
C-052S
C-053
C-053S
C-082
C-082S
C-083-S-HH
C-084S
C-083
C-083-S
C-084
C-162
C-162S
C-163-S
C-163-S-HH
C-164-S
C-164-S-HH
C-167-S
C-165-S
C-163
C-163-HH
C-164
C-165
C-303S
C-304-S
C-306S
C-309S
C-304
C-305
C-305S
C-307S
C-414S
C-415-S
C-419S
C-415
C-609-S
C-417S
HCFC-22
CONNECTION SIZE
BODY
LENGTH(IN.) SURFACE WATER WATER
& TYPE
DIAMETER
A
FILTERING CAP.
CAP.
(IN.) B
AREA SQ. DROPS DROPS
CM
AT 60 AT 60
PPM
PPM
25°C
50°C
1/4 SAE
1.75
4.19
58
61
50
3/8 ODF
1/4 SAE
1/4 SAE
1/4 ODF
1/4 SAE
1/4 SAE
5/16 ODF
1/4 ODF
3/8 SAE
3/8 ODF
1/4 SAE
1/4 ODF
3/8 ODF
1/2 ODF
3/8 SAE
3/8 ODF
1/2 SAE
1/4 SAE
1/4 ODF
3/8 ODF
3/8 ODF
1/2 ODF
1/2 ODF
7/8 ODF
5/8 ODF
3/8 SAE
3/8 SAE
1/2 SAE
5/8 SAE
3/8 ODF
1/2 ODF
3/4 ODF
1-1/8 ODF
1/2 SAE
5/8 SAE
5/8 ODF
7/8 ODF
1/2 ODF
5/8 ODF
1-1/8 ODF
5/8 SAE
1-1/8 ODF
7/8 ODF
1.75
1.75
1.75
1.75
1.75
2.44
2.44
2.44
2.44
2.44
2.62
2.62
2.62
2.62
2.62
2.62
2.62
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.50
3.50
3.50
3.50
3.00
3.50
3.88
4.19
4.19
3.81
4.19
4.75
4.38
4.75
4.19
4.31
5.62
5.12
5.25
5.44
6.06
5.25
6.31
6.25
5.75
5.88
5.88
6.00
6.00
6.93
6.31
6.75
6.75
6.94
7.25
8.88
9.00
9.65
9.75
9.88
10.19
9.25
9.80
9.05
9.35
9.75
10.25
16.00
9.81
70
58
58
58
58
58
97
97
97
97
97
188
135
188
135
188
135
188
213
213
213
213
213
213
213
213
213
213
213
213
342
342
342
342
342
342
342
342
432
432
432
432
684
432
3.1
61
61
3.1
61
149
7.3
7.3
149
7.3
240
12.0
240
12.0
240
12
240
364
17.3
17.3
364
17.3
364
364
17.3
364
364
364
364
34.8
696
34.8
34.8
696
696
34.8
34.8
46.8
936
46.8
936
69.6
46.8
2.5
50
50
2.5
50
119
6.0
6.0
119
6.0
196
9.8
196
9.8
196
9.8
196
297
14.9
14.9
297
14.9
297
297
14.9
297
297
297
297
28.4
567
28.4
28.4
567
567
28.4
28.4
35.7
763
35.7
763
56.7
35.7
R410A
REFRIG. WATER WATER
FLOW
CAP.
CAP.
CAP KW DROPS DROPS
AT 0.07 AT 50 AT 50
BAR DP PPM
PPM
25°C
50°C
5.3
27
20
13.4
5.3
5.3
5.28
5.3
7.4
12.0
7.39
14.4
16.5
7.4
7.39
18.3
33.8
15.8
18.3
28.4
7.4
7.39
18.3
18.3
38.7
38.6
55.9
15.8
15.8
35.5
42.5
38.7
38.6
35.5
52.3
59.4
76.0
43.6
61.4
85.5
55.5
102.0
77.7
1.4
27
27
1.4
27
63
3.2
3.2
63
3.2
104
5.2
104
5.2
104
5.2
104
158
7.9
7.9
158
7.9
158
158
7.9
158
158
158
158
15.1
302
15.1
15.1
302
302
15.1
15.1
20.4
407
20.4
407
30.2
20.4
1.0
20
20
1.0
20
48
2.4
2.4
48
2.4
78
3.9
78
3.9
78
3.9
78
119
6.0
6
119
6
119
119
6
119
119
119
119
11.4
227
11.4
11.4
227
227
11.4
11.4
15.3
305
15.3
305
22.7
15.3
REFRIG. SHIP
FLOW
WT
CAP KW (LBS.)
AT 0.07
BAR DP
MLP $
4.9
1.75
23.93
13.0
4.9
4.9
4.92
4.9
7.0
11.6
7.03
14.0
15.8
7.0
7.03
17.6
33.1
15.4
17.6
27.7
7.0
7.03
17.6
17.6
37.6
37.6
.50
1.75
1.75
.50
1.75
2.44
.75
.75
2.44
.75
2.62
1.25
2.62
1.25
2.62
1.25
2.62
3.00
1.75
1.75
3.00
1.75
3.00
3.00
1.75
3.00
3.00
3.00
3.00
3.50
3.00
3.50
3.50
3.00
3.00
3.50
3.50
4.50
3.50
4.50
3.50
6.00
4.50
25.93
24.89
24.89
23.93
40.39
30.18
33.00
30.14
30.18
30.14
37.11
38.21
42.64
38.71
37.11
37.11
38.75
47.57
48.75
47.57
54.14
51.89
59.18
59.18
53.75
47.57
54.14
51.89
53.75
86.11
85.04
94.11
100.64
85.04
85.04
85.00
92.89
120.50
120.50
130.57
120.50
185.79
134.68
54.5
15.4
15.4
34.4
41.1
37.6
37.6
34.4
50.9
57.7
73.9
42.6
60.0
83.4
54.1
114.0
25.6
DRIERS
Sporlan Replaceable Core Filter-Driers
Features:
• Molded porous core maximum water capacity
• Nut and bolt attachment at end plate allows for simple installation
• Tie-rod construction for easy core replacement
• All internal parts are plated steel
• Exterior shell painted to prevent corrosion
SOURCE 1 PART NO.
SPORLAN CONNECTION
PART NO. SIZE & TYPE
NO. OF
CORES
CORE PART NO.
RCW-48, RCW-4864, or
RCW-4864-HH
RCW-48, RCW-4864, or
RCW-4864-HH
RC-4864, RC-4864-HH OR
RCW-48
RC-4864, RC-4864-HH OR
RCW-48
S1-402082
C-485-G
5/8 ODF
1
S1-402109
C-487-G
7/8 ODF
1
S1-402152
C-489-G
1-1/8 ODF
1
S1-402159
C-4811-G
1-3/8 ODF
1
VOLUME OF
DESICCANT
CU. IN.
48
A
B
C
D
E
F
G
P*
SHIP
WT.
MLP $
9.15
6.00
5.00
5.92
3.50
4.75
0.50
7.50
12.00
453.86
48
9.30
6.00
5.00
6.07
3.72
4.75
.75
7.50
12.00
453.86
48
9.50
6.00
5.00
6.37
3.78
4.75
.91
7.50
12.00
481.10
48
9.60
6.00
5.00
6.37
3.94
4.75
.97
7.50
12.00
489.61
* P Indicates pull space required to change core.
Sporlan Filter Cores
Replaceable Cores
Features:
• Individually packaged in metal cans
• Fully activated
• Hermetically sealed
• Instructions on each can for easy installation
• Includes a triple gasket
RC-4864 – Activated Core - order as separate item - fits types C-480 thru C-19200 series shells. This is the standard core suitable for
most installations in the liquid line or suction line.
RC-4864-HH – Activated Charcoal Core – order as separate item - fits types C-480 thru C-19200 series shells. This core should be
used for wax removal on low temperature R-22 and R-502 systems, and for clean-up after hermetic motor burnout on all types of
sy stems.
RCW-42 — High Water Capacity Core — Order as separate item — Fits ONLY shell types C-R424, C-R425, and CR427.
Designed specially for use w ith POE oils. This core should be used on systems that have a ruptured water cooled condenser, or
that have been exposed to the atmosphere, or for some reason have a high amount of moisture in the system.
SOURCE 1 PART NO.
SPORLAN PART NO.
S1-404360
S1-404380
S1-404400
S1-404401
S1-404403
S1-404404
S1-404420
RC-4864
RC-4864-HH
RC-10098
RCW-48
RCW-100
RCW-42
RC-10098-HH
CORE DIMENSIONS O.D. SHIPPING
X LENGTH
WEIGHT
(LBS.)
3.74” X 5.50”
2.33
3.74” X 5.50”
2.33
4.80 X 6.47
4.67
3.74 X 5.5
28
4.80 X 6.47
4.67
3.18” X 6.00”
2.20
4.80 X 6.47
4.67
FOR USE WITH REPLACEABLE FILTER DRIER
MLP $
C-480 THRU C-19200
C-480 THRU C-19200
C-30000 AND C-40000
C-480 THRU C-19200
C-30000 AND C-40000
C-R424, C-R425 AND C-R427
C-30000 AND C-40000
53.64
83.36
148.50
89.11
193.39
59.00
183.04
Source 1 Bi-Flow Filter-Driers
Features:
• Specifically designed for heat pump or reverse cycle application
• External check valves are not required since they are incorporated within the filter drier shell
• The core design filters out contaminant particles down to 25 microns, 100% copper sweat fittings
• Desiccant core provides three times the filtration as the standard bi-flow
• Core is cushioned in fiber gaskets to protect core and to insure trouble-free performance
• Corrosion-resistant powder coated exterior surpasses 500-hr ASTM salt spray test
Specifications:
Maximum w orking pressure: 680 psi*
*Note: Above pressure rating is valid for Source 1 driers manufactured after June, 2009. These driers can be identified by the UL mark
on the box and drier label.
SOURCE 1 PART NO.
TYPE
ODF
CU IN.
MLP $
S1-BFD083S
S1-BFD163S
BI-FLOW
BI-FLOW
3/8
3/8
8
16
27.68
33.04
71
DRIERS
Sporlan Catch-All Suction Line Filter-Driers
Sporlan Suction Line Filter-Driers are designed specifically for CLEAN-UP after BURNOUT using the HH TYPE CHARCOAL CORE.
Features:
• Positive protection for the compressor, Most economical method of clean-up
• Minimum down time — system operates during clean-up.
• Method is applicable to almost any size system
• Removes all contaminants — moisture, acid, sludges, dirt…
• Recommended by the leading equipment manufacturers
SOURCE 1 PART NO.
SPORLAN PART NO.
CONNECTION SIZE & TYPE
S1-401026
S1-401029
S1-401030
S1-401033
S1-401316
S1-401318
C-164-S-T-HH
C-165-S-T-HH
C-166-S-T-HH
C-167-S-T-HH
C-307-S-T-HH
C-309-S-T-HH
1/2 ODF
5/8 ODF
3/4 ODF
7/8 ODF
7/8 ODF
1-1/8 ODF
BODY
LENGTH A SURFACE SHIP WT.
DIAMETER
(Inches) FILTERING
(Inches)
AREA (Sq
Cm)
3.00
6.00
213
1.75
3.00
6.31
213
1.75
3.00
6.75
213
1.75
3.00
6.93
213
1.75
3.00
9.80
342
3.5
3.00
9.75
342
3.5
MLP $
74.50
77.18
82.82
82.82
128.04
136.96
Sporlan Reversible Heat Pump Filter-Driers
Features:
• A short overall length for easy installation.
• Proven metal check valves used in construction – no synthetic materials.
• The Sporlan dependable molded core used for maximum filtration ability. When the flow direction reverses, dirt already collected
remains in the filter-drier, Drier operates in either flow direction with low pressure drop.
• A carefully engineered blend of desiccants for maximum water capacity and acid removal ability.
• The HPC-160-HH Series also has the HH style core with activated charcoal which offers maximum ability to remove oleoresin and
other reactive chemical constituents in the oil.
• Same rugged construction as used in the Catch-All, Maximum working pressure: 650 psi
• Compatible with refrigerants 12, 22, 134a, 404A, 407C,410A, 502, 507
DIMENSIONS
SOURCE 1 PART NO.
SPORLAN
MODEL NO.
CONN
S1-401372
S1-401373
S1-404101
S1-404161
S1-404180
S1-404201
HPC-305-S-HH
HPC-307-S-HH
HPC-103-S
HPC-104-S
HPC-163-HH
HPC-163-S-HH
5/8 ODF
7/8 ODF
3/8 ODF
1/2 ODF
3/8 SAE
3/8 ODF
S1-404241
S1-404281
HPC-164-S-HH
HPC-165-S-HH
1/2 ODF
5/8 ODF
FLOW WATER
CAP
CAP
TONS@ R-22
1PSI DROPS
@60PPM
FLOW WATER
WATER CAP
LIQUID CAP
CAP CAP R-22
R-410A
OUNCES@100F
TONS DROPS@ DROPS@50PPM
@1PSI 60PPM
BODY LENGTH SURFACE WATER WATER REFRIG SHIP
DIAM B
A
FILTERING
CAP
CAP
FLOW
WT
AREA SQ. DROPS DROPS CAP @ (LBS.)
IN.
(125°) (125°) AT 2 PSI
AT 60 60 PPM PRESS.
PPM
125°F DROP
75°F
(TONS)
3.00
10.42
9.8
167
10.8
3.00
11.02
10.6
167
10.8
3.00
5.88
18
215
176
4.7
1.75
3.00
6.00
18
215
176
6.3
1.75
3.00
7.78
4.7
93
4.8
3.00
6.92
26
93
81
3.7
3.00
3.00
7.07
7.35
26
26
93
93
81
81
4
6.8
R-22
125F
75F
125F
R-22
R-410A
MLP $
10.8
10.8
119
119
123
123
109
109
19.7
19.7
17.2
17.2
4.8
81
69
100
14.5
12.6
144.96
147.86
64.89
66.00
95.29
95.29
96.79
99.14
1.75
Sporlan Compact Style Suction Line Filter-Driers
Features:
• Short overall length
• Suitable for cramped piping situations
SOURCE 1 PART NO.
SPORLAN MODEL NO.
S1-400806
S1-400811
C-146-S-TT-HH
C-147-S-TT-HH
72
CONNECTION SIZE
AND TYPE
3/4 ODF
7/8 ODF
BODY
DIAMETER
4.44
4.44
LENGTH
4.83
4.97
SHIP
WT
2
2
MLP $
93.68
96.36
FILTERS
Sporlan SF – Suction Filter
Types With Bypass Relief Valve (Bi-Directional Flow)
SPORLAN PART NO.
RATINGS AT ARI STANDARD 730
CONDITIONS
SOURCE 1 PART NO.
W/O
ACCESS
VALVE
W/ACCESS
VALVE
CONN
FILTER
AREA
SQ. IN.
OVERALL
LENGTH
SHELL
DIA
SHIP WT
(LBS.)
S1-800001
S1-800002
S1-800006
S1-800008
S1-800037
S1-800120
—
—
—
—
—
—
SF-286-T
SF-287-T
SF-289-T
SF-4811-T
SF-285-T
SF-489-T
3/4 ODF
7/8 ODF
1-1/8 ODF
1-3/8 ODF
5/8 ODF
1-1/8 ODF
28
28
28
48
28
48
8.79
8.93
9.51
13.10
8.34
12.42
3.0
3.0
3.0
3.0
3.0
3.0
2.25
2.25
2.25
3.0
2.25
3.0
WATER
WATER
REFRIG
CAP
CAP
FLOW CAP
DROPS @ DROPS @ TONS @ 3
60 PPM
60 PPM
PSI
75°F
125°F
N/A
N/A
8.6
N/A
N/A
11.1
N/A
N/A
14.8
N/A
N/A
18.4
N/A
N/A
6.4
N/A
N/A
16
MLP $
101.61
101.61
108.04
157.04
94.07
157.04
Types Without Bypass Relief Valve (Single Flow Direction)
SPORLAN PART NO.
SOURCE 1 PART NO.
W/O
ACCESS
VALVE
S1-800013
S1-800182
SF-115
—
RATINGS AT ARI STANDARD
730 CONDITIONS
W/ACCESS
VALVE
SF-6417-T
CONN
FILTER
AREA SQ.
IN.
OVERALL
LENGTH
5/8 ODF
2-1/8 ODF
11
388*
4.60
10.94
40° F.
SF-114
SF-115
–
–
–
–
–
–
–
–
–
2.00
4.75
.75
7.50
WATER WATER
REFRIG
CAP
CAP
FLOW CAP
DROPS @ DROPS @ TONS @ 3
60 PPM
60 PPM
PSI P
75°F
125°F
N/A
N/A
4.1
N/A
N/A
91.1
MLP $
47.57
377.11
SELECTION RECOMMENDATIONS
** FLOW CAPACITY IN TONS EVAPOR ATOR TEMPER ATURE
TYPE NUMBER
W ITHOUT
ACCESS
VALVE
SHELL DIA SHIP WT
(LBS.)
W ITH
ACCESS
VALVE
CONNECTIONS
INCHES
–
–
SF-285-T
SF-286-T
SF-287-T
SF-289-T
SF-489-T
SF-4811-T
SF-4813-T
SF-6417-T
SF-6421-T
1/2 ODF
5/8 ODF
5/8 ODF
3/4 ODF
7/8 ODF
1-1/8 ODF
1-1/8 ODF
1-3/8 ODF
1-5/8 ODF
2-1/8 ODF
2-5/8 ODF
20° F.
2
12
1.3
2.3
3.5
4.3
6.3
8.2
8.7
9.9
11.7
46.7
50.5
3
134A
1.5
2.6
4.0
5.1
7.0
9.2
9.9
11.2
13.3
50.9
62.9
22
2.4
4.1
6.4
8.6
11.1
14.8
16.0
18.4
21.6
91.1
119.0
0° F.
PRESSURE DROP
1-1/2
2
1
REFRIGERANT
12
134A
22
12
134
0.9
1.0
1.5
0.6
0.6
1.6
1.7
2.7
1.0
1.1
2.5
2.7
4.0
1.6
1.7
3.1
3.4
5.0
2.0
2.1
4.4
4.6
7.2
2.7
2.8
5.7
6.0
9.4
3.5
3.7
6.1
6.5
10. 0
3.7
3.9
6.8
7.3
11. 4
4.2
4.4
8.1
8.7
13. 5
4.9
5.2
28. 7
31.0
56. 9
15.8
16.4
36. 8
38.6
70. 2
20.2
20.6
–20° F.
–40°
F.
1-1/2
1/2
1
1/2
22
1.1
1.8
2.9
3.6
5.1
6.6
7.0
7.9
9.4
31. 8
44. 0
12
0.3
0.5
0.9
1.1
1.4
1.8
1.9
2.2
2.6
7.2
9.1
22
0.7
1.2
1.8
2.2
3.1
4.0
4.3
4.8
5.6
20.3
25. 6
22
0.3
0.6
1.0
1.2
1.5
2.1
2.2
2.5
2.9
9.3
11.8
NOMINAL SYSTEM
HORSEPOW ER
REFRIGERANT
22 12, 134A, 502
1
1/2
2
1
4
1-1/2
5
1-1/2
7-1/2
3
7-1/2
5
10
5
12
5
15
7
55
20
60
30
**Refrigerant 502 flow capacity is 80% of the values shown for Refrigerant 22, when expressed in TONS. When expressed in horsepower, the proper
refrigerant selection is the same as for R-12.
* The SF-6400 series uses a pleated filter that greatly increases the square inch filter area.
THERMOSTATIC EXPANSION VALVES
Danfoss Universal TR 6 Expansion Valve Kits
The Danfoss Universal TR 6 thermostatic expansion valve (TXV) is available in seven models that cover original equipment
manufacturer (OEM) air-conditioner and heat pump designs, from 11/2 to 6 tons in R-22 and R-410A systems.
Kit Includes:
• Valve with 3/8” x 3/8” ODF connections, 24” equalization line and 311/2” capillary tube
• Chatleff and Aeroquip adapters
• Built-in check valve for heat pumps
• 35” foam insulating tape
• Patented easy secure copper bulb strap Instructions
SOURCE 1 PART NO.
SYSTEM CAPACITY
DANFOSS MODEL
REFRIGERANT
MLP $
S1-067L5856
S1-067L5857
S1-067L5858
1-1/2 - 2 Tons
2-1/2 - 3 Tons
3-1/2 - 4 Tons
067L5856
067L5857
067L5858
R22
R22
R22
176.79
196.25
196.25
S1-067L5859
S1-067L5955
S1-067L5956
S1-067L5957
5 - 6 Tons
1-1/2 - 2 Tons
3-1/2 - 4 Tons
4-1/2 - 5 Tons
067L5859
067L5955
067L5956
067L5957
R22
R410A
R410A
R410A
176.79
176.79
176.79
176.79
73
Sporlan “O” Series Expansion Valves
Sporlan Type O valve is a brass bar body, externally adjustable valve with ODF solder connections. The thermostatic element is
replaceable, and the inlet connection has a permanent 12 mesh strainer. This valve type features a balanced port construction, and it
is designed for both air conditioning and refrigeration applications. A synthetic seating surface provides tight shut-off during system off
periods. This valve type has two body styles: a small body which provides capacities up to 30 tons R-22, and a large body which
extends capacities to 70 tons R-22.
Features:
• Balanced port construction
• External equalizer with 1/4” ODF connection
• Connections in straight through flow configuration
• Remote bulb tubing length 60” (152 cm)
• Standard factory air test superheat setting at 7° F
CONNECTION SIZE
SOURCE 1 PART NO.
SPORLAN PART NO.
REFRIGERANT
INLET
OUTLET
R22
R22
R22
R22
R22
CAPACITY
RANGE TONS
15
20
30
40
55
S1-124226
S1-124233
S1-124240
S1-124247
S1-124261
OVE-15-GA-7/8 X 1-1/8 X 1/4 X 5’
OVE-20-GA-7/8 X 1-3/8 X 1/4 X 5’
OVE-30-GA-1-1/8 X 1-3/8 X 1/4 X 5’
OVE-40-GA-1-1/8 X 1-3/8 X 1/4 X 5’
OVE-55-GA-1-1/8 X 1-3/8 X 1/4 X 5’
7/8 ODF
7/8 ODF
1-1/8 ODF
1-1/8 ODF
1-1/8 ODF
S1-125396
OZE-20-GA, 7 X 9 ODF, 60"
R410A
20
7/8 ODF
MLP $
1-1/8 ODF
1-3/8 ODF
1-3/8 ODF
1-3/8 ODF
1-3/8 ODF
SHIP WT.
(LBS.)
3.00
3.00
3.00
5.00
5.00
399.07
399.07
399.07
720.57
720.57
1-1/8 ODF
3.00
570.36
Sporlan “S” Series Expansion Valves
Sporlan Type S valve is a brass bar body, externally adjustable valve with ODF solder connections. The thermostatic element is
replaceable and the inlet connection has a permanent 12 mesh strainer. This valve is designed for both air conditioning and
refrigeration applications.
Features:
• External equalizer with 1/4” ODF connection
• Connections in straight through flow configuration
• Remote bulb tubing length 60” (152 cm)
• Standard factory air test superheat setting at 7° F
CONNECTION SIZE
SOURCE 1 PART NO.
SPORLAN PART NO.
REFRIGERANT
S1-129054
S1-129118
S1-129201
S1-129334
S1-129383
SVE-2-GA-1/2 X 5/8 X 1/4 X 5’
SVE-3-GA-1/2 X 5/8 X 1/4 X 5’
SVE-4-GA-1/2 X 7/8 X 1/4 X 5’
SVE-8-GA-5/8 X 7/8 X 1/4 X 5’
SVE-10-GA-5/8 X 7/8 X 1/4 X 5’
R22
R22
R22
R22
R22
CAPACITY RANGE
TONS
2
3
4
8
10
INLET
OUTLET
1/2 ODF
1/2 ODF
1/2 ODF
5/8 ODF
5/8 ODF
5/8 ODF
5/8 ODF
7/8 ODF
7/8 ODF
7/8 ODF
SHIP WT.
(LBS.)
3.00
3.00
3.00
3.00
3.00
MLP $
358.66
341.11
341.11
266.39
341.11
Sporlan EBSVE Series Expansion Valves
Features:
• Brass body
• Balanced port construction
• Extended ODF solder connections
• Suitable for large A/C applications which operate over widely-varying conditions
• Long-lasting stainless steel diaphragm
• Externally adjustable siperheat
CONNECTION SIZE
SOURCE 1 PART NO.
SPORLAN PART NO.
REFRIGERANT
CAPACITY RANGE TONS
INLET
OUTLET
S1-163556
S1-163773
EBSVE-8-GA,5/8 X 7/8 ODF,60"
EBSVE-11-GA,5/8 X 7/8 ODF,60"
R-22
R-22
8
11
5/8
5/8
7/8
7/8
74
SHIP WT.
(LBS.)
1.5
1.5
MLP $
306.46
306.46
Sporlan ERZE Series Expansion Valves
Sporlan RZE Series Expansion Valves The RZE valve is an externally adjustable balance ported TEV designed for R-410A air
conditioning applications. This makes the RZE valve an excellent replacement for all OEM BI and BBI valves as well as other
applications requiring a R-410A expansion valve such as I and RI valves. The RZE valve utilizes the KT-45 element design for the
higher pressure s of R-410A. T his valve may also be applied in bi-directional applications.
CONNECTION SIZE
SOURCE 1 PART NO.
SPORLAN PART NO.
REFRIGERANT
S1-168719
S1-168720
S1-168794
S1-168802
ERZE-8-GA, 5 X 7 ODF
ERZE-15-GA, 5 X 7 ODF
ERZE-6-GA
ERZE-12.5-GA, 5 X 9 ODF
R410A
R410A
R410A
R410A
CAPACITY
RANGE
TONS
8
15
6
12.5
INLET
OUTLET
SHIP WT.
(LBS.)
MLP $
5/8
5/8
1/2
5/8
7/8
7/8
5/8
1-1/8
1.5
1.5
310.39
310.39
215.46
310.39
1.5
Sporlan RC Series Expansion Valves
Small brass body, externally adjustable valve available for R-22 and R-410 air conditioning and heat pump applications. The valve
contains an internal check valve to eliminate the need for external bypass check valve on heat pump applications. Suitable for
replacing OEM type TEVs with or without internal check valve on these applications.
CONNECTION SIZE
SOURCE 1 PART NO.
SPORLAN PART NO.
REFRIGERANT
CAPACITY RANGE TONS
INLET
S1-151245
S1-151252
S1-151253
S1-151258
S1-151265
S1-151270
S1-151277
S1-151365
S1-151366
S1-151368
S1-151492
RCVE-3-GA,3/8 X 1/2 ODF,30"
RCVE-4-GA,1/2 X 1/2 ODF,30"
RCVE-2-GA,3/8 X 1/2 SAE,30"
RCVE-5-GA,1/2 X 1/2 ODF,30"
RCVE-2-GA,3/8 X 1/2 ODF,30"
RCVE-5-GA,1/2 X 1/2 SAE,30"
RCVE-3-GA,3/8 X 1/2 SAE,30"
RCZE-2-GA,3/8 X 1/2 ODF,30"
RCZE-3-GA,3/8 X 1/2 ODF,30"
RCZE-4-GA,1/2 X 1/2 ODF,30"
RCZE-5-GA,1/2 X 1/2 ODF,30"
R-22
R-22
R-22
R-22
R-22
R-22
R-22
R410A
R410A
R410A
R410A
3
4
2
5
2
5
3
2
3
4
5
3/8
1/2
3/8
1/2
3/8
1/2
3/8
3/8
3/8
1/2
1/2
75
OUTLET SHIP WT.
(LBS.)
1/2
1.5
1/2
1.5
1/2
1.5
1/2
1.5
1/2
1.5
1/2
1.5
1/2
1.5
1/2
1.5
1/2
1.5
1/2
1.5
1/2
1.5
MLP $
217.46
217.46
284.21
217.46
217.46
278.46
278.46
266.07
266.07
266.07
340.71
SOLENOID VALVES AND COILS
Sporlan “E” Series Solenoid Valves
Features:
• Solenoid Valve Coil not included
• Extended connections
• Normally closed
Application:
• Mounted vertical, horizontal, or side
• Installation without disassembly
DIM
SOURCE 1 PART NO.
S1-3217-00
S1-3227-00
S1-3233-00
S1-3246-00
S1-3284-00
S1-3291-00
S1-3368-00
S1-3402-00
S1-3441-00
S1-3505-00
S1-3525-00
S1-3576-00
S1-4033-00
S1-4077-00
S1-4079-00
S1-4100-00
S1-4101-00
SPORLAN PART NO. REFRIGERANT
E3S120
E3S130
E6S130-HP
E5S130
E6S130
E6S140
E9S240
E9S250-HP
E10S250
E14S250
E10S240-HP
E19S270
E9S240-HP
E19S270-HP
E5S130-HP
E14S250-HP
E2S120-HP
R-22
R-22
R410A
R-22
R-22
R-22
R-22
R410A
R-22
R-22
R410A
R-22
R410A
R410A
R410A
R410A
R410A
CONN
PORT
SIZE
1/4 ODF
3/8 ODF
3/8 ODF
3/8 ODF
3/8 ODF
1/2 ODF
1/2 ODF
5/8 ODF
5/8 ODF
5/8 ODF
1/2 ODF
7/8 ODF
1/2 ODF
7/8 ODF
3/8 ODF
5/8 ODF
1/4 ODF
0.094
0.094
0.188
0.156
0.188
0.188
0.281
0.281
0.313
0.438
0.313
0.594
0.281
0.594
0.156
0.438
0.075
NOMINAL
CAPACITY @
2 PSI
1.3
1.3
4.0
2.8
4.0
4.0
6.6
6.6
9.1
12.9
9.1
19.8
6.6
19.8
2.8
12.9
0.95
A
B
C
D
SHIP USE COIL KIT
WT
4.63
4.56
4.63
4.56
4.63
5.0
5.0
6.5
6.5
6.88
5.0
7.13
5.0
7.13
4.56
6.88
4.63
0.55
0.49
0.75
0.53
0.75
0.75
0.75
0.69
0.86
0.47
0.86
0.81
0.75
0.81
0.53
0.47
0.55
2.04
2.1
2.44
2.48
2.44
2.44
2.7
2.24
3.13
3.25
3.13
3.41
2.7
3.41
2.48
3.25
1.96
0.29
0.19
0.31
0.23
0.31
0.31
0.31
0.31
0.39
—
0.39
—
0.31
—
0.23
—
0.31
1.0
2.0
1.2
1.2
1.2
1.2
1.7
1.7
2.3
2.3
2.3
2.6
1.7
2.6
1.2
2.3
1
MKC-1
MKC-1
MKC-1
MKC-1
MKC-1
MKC-1
MKC-2
MKC-2
MKC-2
MKC-2
MKC-2
MKC-2
MKC-2
MKC-2
MKC-1
MKC-2
MKC-1
MLP $
110.43
110.43
130.96
110.43
130.96
130.96
169.61
169.61
200.71
217.82
200.71
354.57
169.61
354.57
110.43
217.82
156.19
Sporlan “ME” Series Solenoid Valves
Features:
• With manual lift stem
• Solenoid Valve Coil not included
• Normally closed, Extended connections
• Application:
• Mounted vertical, horizontal or side
• Installation without disassembly
SOURCE 1 PART NO.
SPORLAN PART NO.
REFRIGERANT
CONN
PORT SIZE
S1-3310-00
S1-3315-00
S1-3322-00
S1-3390-00
S1-3394-00
S1-3396-00
S1-3460-00
S1-3466-00
S1-3524-00
S1-3528-00
S1-3590-00
S1-3591-00
S1-3596-00
S1-3666-00
S1-3672-00
S1-4036-00
S1-4076-00
ME6S130-HP
ME6S130
ME6S140
ME9S230
ME9S240-HP
ME9S240
ME10S240
ME10S250
ME14S250-HP
ME14S250
ME19S250
ME19S270-HP
ME19S270
ME25S270
ME25S290
ME25S290-HP
ME6S140-HP
R410A
R-22
R-22
R-22
R410A
R-22
R-22
R-22
R410A
R-22
R-22
R410A
R-22
R-22
R-22
R410A
R410A
3/8 ODF
3/8 ODF
1/2 ODF
3/8 ODF
1/2 ODF
1/2 ODF
1/2 ODF
5/8 ODF
5/8 ODF
5/8 ODF
5/8 ODF
7/8 ODF
7/8 ODF
7/8 ODF
1-1/8 ODF
1-1/8 ODF
1/2 ODF
0.188
0.188
0.188
0.281
0.281
0.281
0.313
0.313
0.458
0.438
0.594
0.594
0.594
0.781
0.781
0.781
0.188
76
NOMINAL
CAPACITY @ 2 PSI
(TONS) (R-22)
4.0
4.0
4.0
6.6
6.6
6.6
9.1
9.1
12.9
12.9
17.2
19.8
19.8
33.7
33.7
33.7
4.0
DIM A
4.63
4.63
5.00
4.63
5.00
5.00
5.00
6.50
6.88
6.88
6.88
7.13
7.13
7.50
8.50
8.50
5.00
SHIP WT USE COIL KIT
(LBS.)
1.25
1.25
1.25
1.75
1.75
1.75
2.00
2.00
2.25
2.25
3.75
3.75
3.75
6.00
6.00
6.00
1.25
MKC-1
MKC-1
MKC-1
MKC-2
MKC-2
MKC-2
MKC-2
MKC-2
MKC-2
MKC-2
MKC-2
MKC-2
MKC-2
MKC-2
MKC-2
MKC-2
MKC-1
MLP $
174.21
174.21
174.21
215.39
215.39
215.39
245.14
245.14
262.50
262.50
399.11
399.11
399.11
559.25
559.25
559.25
174.21
SOLENOID VALVES AND COILS
Sporlan Replacement Solenoid Valve Coil Kit
MKC-1 & MKC-2
Features:
• Designed for continuous duty
• Supplied with junction box
• Electrical specifications listed on coil & nameplate
• Blue lead wire
VA
SOURCE 1 PART NO.
SPORLAN MODEL NO.
VOLTS / HZ
WATTS
HOLDING
INRUSH
MLP $
S1-310000
S1-310156
S1-310286
S1-310325
S1-311424
S1-311515
MKC-1,120V/50-60HZ,10W
MKC-1,208-240V/50-60HZ,10W
MKC-1,DUAL JAU *
MKC-1,24V/50-60HZ,10W
MKC-2,120V/50-60HZ,10W
MKC-2,208-240V/50-60HZ,10W
120 VOLT 50/60 HZ
208-240 VOLT 50/60 HZ
120/208-240 50/60HZ
24 VOLT 50/60 HZ
120 VOLT 50/60 HZ
208-240 VOLT 50/60 HZ
10
10
10
10
15
15
0.14
0.09
.14/.09
0.63
0.26
0.13
0.39
0.19
.39/.19
1.9
0.6
0.31
81.82
81.82
106.32
81.82
98.14
98.14
S1-311671
S1-311710
MKC-2,DUAL JAU *
MKC-2,24V/50-60HZ,10W
120/208-240 50/60HZ
24 VOLT 50/60 HZ
15
15
.23/.13
1.4
.60/.31
3.1
127.61
98.14
* J = Junction Box, A = 1/32" Insulation
CHECK VALVES
Parker Check Valves
SOURCE 1 PART NO.
CONNECTION SIZE
MLP $
S1-274001-10
S1-274003-10
S1-274004-10
S1-274005-10
S1-274006-10
3/8 SWEAT
1/2 SWEAT
5/8 SWEAT
7/8 SWEAT
1-1/8 SWEAT
11.36
14.11
25.25
44.36
58.29
REFRIGERATION BALL VALVES
Sporlan EBV Refrigeration Ball Valves
Features:
• Forged brass body construction with extended copper fittings
• Full-size ports for unrestricted flow on most sizes (1/4” through 3-1/8”)
• Dual Teflon seals surround the polished, brass ball with a secondary seal to prevent leakage due to foreign material
• Dual Teflon stem seals with internal packing nut for the primary seal; no synthetic “O” rings
• Fully open to fully closed with a 1/4-turn
• Positive movement ensured with internal, forged mechanical stops
• No need to remove the seal cap to open or close the valve
• Ball internal relief port design ensures positive shut-off in either flow direction—even during system evacuation
• Full refrigeration service temperature range: –40°F to 325°F (–40°C to 149°C)
• Design working pressure: 700 psig
SOURCE 1 PART NO.
SPORLAN MODEL NO.
CONNECTION SIZE
MLP $
S1-502031
S1-502033
S1-502035
S1-502039
S1-502041
EBV-1030
EBV-1040
EBV-1050
EBV-1070
EBV-1090
3/8 SWEAT
1/2 SWEAT
5/8 SWEAT
7/8 SWEAT
1-1/8 SWEAT
67.64
67.21
74.11
96.43
146.18
77
WHITE RODGERS GAS VALVES
36H Series Universal Fast Open High Capacity Gas Valves
36H valves are used for proven pilot applications, and can replace more than 93 valves in the 36C68/36C76 series. Improvements
over the 36C series include: field convertible from Natural to LP, independently field adjustable two-stage regulators and electric on/off
switch.
Features:
• 320K BTU at 1” pressure drop versus 280K BTU at 1” for the 36C series
• Diaphragm size increased 15% over 36C series resulting in improved regulation set point stability
• Quiet design, DC rectified
• Independently adjustable high/low two stage
• Direct ignition or proven pilot
• 24 volt, 50/60 Hz
• 0.75” x 0.75”; 0.25” press tap in and out
• 50k–400k BTU range of regulation
• Straight through design
SOURCE 1 PART NO.
STAGES
MLP $
S1-36H32-304
S1-36H32-423
S1-36H33-412
S1-36H64-463
S1-36H65-401
SINGLE
SINGLE
SINGLE
TWO
TWO
272.29
266.11
282.14
355.96
359.89
SOURCE 1PART NO.
S1-36H32-304
S1-36H33-412
S1-36H65-401
S1-36H32-423
S1-36H64-463
36C81 410S1
36C81 451B1
36C81 451P1
36C81 451S1
36E24 202B1
36E24 202P1
36E24 202S1
36E24 203S1
36E96 227P1
36E96 227B1
36C68-200
36C68-202
36C68-205
36C68-209
36C68-212
36C68-217
1RC52
36C76-205
36C76-210
36E24 203P1
36E24 203B1
36E24 204B1
36E24 204P1
36E24 205S1
36E24 205P1
36E24 205B1
36E24 206B1
36E96 231S1
36E96 231P1
36C68-218
36C68-243
36C68-261
36C68-262
36C68-266
36C68-301
36C76-214
36C76-225
36C76-227
36E24 206P1
36E24 206S1
36E24 207B1
36E24 207P1
36E24 207S1
36E24 208S1
36E24 208P1
36E24 208B1
36E96 231B1
36E96 234P1
36C68-303
36C68-324
36C68-325
36C68-326
36C68-327
36C68-330
36C76-230
36C76-401
36C76-406
REPLACES
36E36-304
36E24 209B1 36E24 211B1
36E24 209P1 36E24 211S1
36E24 210B1 36E24 212B1
36E24 210P1 36E24 214JS
36E24 211P1 36E24 214B1
36E24 211S1 36E24 214S1
36E24 211P1 36E24 218P1
36E24 211B1 36E52 214S1
36E96 234B1 36E96 238B1
36E96 238P1 36E96 257B1
36C68-419
36C68-400
36C68-423
36C68-403
36C68-434
36C68-404
36C68-441
36C68-405
36C68-442
36C68-415
36C68-448
36C68-418
36C76-407
36C76-412
36C76-408
36C76-417
36C76-411
36C76-420
36E52 214JS
36E92 201S1
36E92 201B1
36E98 201P1
36E98 201B1
36E98 201S1
36E98 202S1
36E98 202P1
36E96 314JS
36E96 314S1
36C68-452
36C68-457
36C68-464
36C68-472
36C68-473
36C68-477
36C76-445
36C76-459
36C76-463
36E98 202B1
36E98 204S1
36E98 206B1
36E98 206S1
36E98 206P1
36E98 301B1
36E98 304S1
36E98 304JS
36H55-201B1
36H55-202B1
36C68-601
36C68-602
36C68-606
36C68-607
36C68-806
700-418
36C76-467
36D13-208
36D13-405
36E98 304GR
36H23-401B1
36H23-402P1
36H33 313B1
36H33 314B1
36H33 415B1
36H33 416B1
36H55-403B1
36H55-404P1
700-420
V845A1109
VR8304M4507
VR8345M4302
36D13-208
36H64-463
700-413
36J Series Universal Gas Valves
The 36J combination gas control valve is a versatile multifunction control designed to meet the requirements for use with non-piloted
intermittent ignition systems (Direct Spark Ignition, Hot Surface Ignition). Models include fast and slow open single and two stage
valves. These valves are also convertible for natural/LP gases. Along with its reduced size, all control adjustments and features, as
well as the system interface-wiring panel, have been designed on the top surface of the control for simplified application and easy
accessibility. The 36J gas control is designed to meet today’s requirement for maximum capacity, smaller size and highly effici ent gas
sy stems.
Features:
• Patented coaxial solenoid design.
• Inlet and optional outlet screens help protect from debris.
• Controlled gasket compression.
• Tamper resistant screws.
• Built-in hose connections for simplified field service or Std. 1/8” NPT (optional).
• Conveniently located electric on-off switch.
• Versatile mounting.
SOURCE 1 PART NO.
STAGES
REPLACES
MLP $
S1-36J22-214
S1-36J24-214
S1-36J24-614
S1-36J54-214
S1-36J55-214
S1-36J55-614
SINGLE
SINGLE
SINGLE
TWO
TWO
TWO
36G22-214
36G24-214
CARRIER 36G24-618P1 & 36J24-618P1
36G54-214
36G55-214
CARRIER 36G55-618P1 & 36J55-618P1
154.89
150.46
144.00
218.68
227.39
232.86
78
WHITE RODGERS GAS VALVES
36C Replacement Gas Controls
Features:
• Valve may be mounted in any position, except upside down.
• Both main valve seat and line-interrupter seal with line pressure, assuring positive gas seal-off.
• Inlet screen, pilot gas filter and top operated main valve provide maximum protection against chips and dirt.
• Gas cock knob, pilot adjust screw and regulator adjustment are on top of control.
• Thermocouple connection on models with line interrupter and combination tab/screw terminals on 24 VAC models.
• Easy grip pipe boss simplifies installation. Built-in regulator system provides constant outlet pressure throughout entire usable
capacity of valve, regardless of inlet pressure fluctuations.
• For use with all gases. (All models include LP Conversion kits.)
• Model 36C03 (24V) is for use with thermocouple (H06E Series, p. 99).
• Model 36C03U is for use with 750 millivolt power generator (S1-G01A-332, p. 99) and may be used with 250 millivolt system if
nonanticipated room thermostat is used. Must be used in vented application.
Specifications
Regulator Setting: Natural gas, 3-1/2” W.C.
Regulator Adj ustment Range: 2-1/2” to 5” W.C.
Ambient Operating Range: –40 to +175° F (–40 to +79° C)
Maximum Pressure Rating: 1/2 PSI (14.0” W.C.)
Pilot Gas Connection: 1/4” compression fitting furnished.
Pressure Tap: 1/8” NPT.
Body Pattern: Straight through.
SOURCE 1 PART NO.
COIL VOLTAGE
S1-36C03-300
S1-36C03-333
S1-36C03-400
S1-36C03-433
S1-36C03U-333
24 VAC, 60 HZ
24 VAC, 60 HZ
24 VAC, 60 HZ
24 VAC, 60 HZ
750 MV
INLET-OUTLET CAPACITY AGA
SIZE
STANDARD
GAS*
1/2 X 3/4
230,000
1/2 X 3/4
230,000
3/4 X 3/4
280,000
3/4 X 3/4
280,000
1/2 X 3/4
230,000
GAS
NAT
NAT
NAT
NAT
NAT
LP
REDUCER
CONVERSION BUSHING
KIT
KIT
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
SIDE
TAPS
NO
YES
NO
YES
YES
LINE
INLET
INTERRUPTER PRESSURE
TAP
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
MLP $
189.57
206.14
205.07
261.07
296.79
Conversion Kits for White-Rodgers Gas Valves
SOURCE 1 PART NO.
TYPE OF CONVERSION
USED WITH VALVE TYPE
MLP $
S1-F92-0656
PROPANE TO NATURAL
36C & 36E VALVES W/REGULATOR RANGE OF 2.5" TO 5.0" W.C.
14.00
79
HONEYWELL GAS VALVES
V800 Standing Pilot Gas Valve
Used on gas fired standing pilot appliances with 30 mV thermocouple. These gas controls include a manual gas
valve, safety shutoff, single millivoltage automatic operator, and pressure regulator, pilot gas filter and
flowadjustment, pressure tapping, and thermocouple connector. V800 is used on 24V systems.
Features:
• Include pilot flow adjustment screw.
• Easy to install, adjust and service; all adjustments and connections are accessible from top of control.
• Add separate energy cutoff (ECO) where codes call for dual safety shutoff.
• Complete safety shutoff on pilot flame failure.
• LITE-RITE (OFF-PILOT-ON) lighting sequence.
• ECO connector for V800 models. Part No. 392451-1.
Specifications:
Type: Single Stage
Ignition Type: Standing Pilot
Type of Gas: Natural or LP
Body Pattern: Straight-through, multi-tapped with 1/2" right and left outlets plugged
Note: No side outlets on S1-VA800A1476.
Pressure Ratings (psi): 1/2 psi
Pressure Ratings (kPa): 3.5 kPa
Pilot Gas Outlet: Compression fitting for 1/4” OD tubing
Pressure Tapping: 1/8” NPT with plug
Electrical Ratings: 24 VAC
Frequency: 60 Hz
Anticipator Setting: .2 A
Temperature Range (F): 32°F to 175°F
Temperature Range (C): 0°C to 79°C
Mounting: 0 to 90 degrees in any direction from the upright position of the gas control knob, including vertically.
Dimensions (in.): 4-3/4”H x 4-1/16”W x 3-3/16”D
Dimensions (mm): 121 mm H x 103 mm W x 81 mm D
Approv als: American Gas Association IAS AGA Design Certified; File No. L2025003, CGA Design Certified;
File No. L2025003, UL Component Recognized; Underwriters Laboratories Inc UL Component Recognized.
PRESSURE
REGULATOR SETTING
SOURCE 1 PART INLET-OUTLET
NO.
SIZE
S1-V800A1070
1/2 IN. x 3/4 IN.
OPENING
STANDARD
CAP @ 1 IN
P.D.
250,000
BTU/HR
S1-V800A1088
3/4 IN. x 3/4 IN.
STANDARD
335,000
BTU/HR
S1-V800A1476
1/2 IN. x 3/4 IN.
STANDARD
S1-V800C1052
3/4 IN. x 3/4 IN.
STEP
OPENING
250,000
BTU/HR
335,000
BTU/HR
PSI
3.5 IN. WC
3.5 IN. WC
3.5 IN. WC
FULL RATE:
3.5 IN. WC;
STEP
SETTING:
0.9 IN. WC
KPA
ELECTRIACAL CONNECTIONS
ACCESSORIES INCLUDED
COMBINATION SCREW AND 1/4 ONE Q340 THERMOCOUPLE, ONE 3/4 x 1/2 IN
IN. MALE QUICK CONNECTS
REDUCER BUSHING, ONE 1/2 x 3/8 IN
REDUCER BUSHING, AND NATURAL TO LP
CONVERSION KIT
COMBINATION SCREW AND 1/4 ONE Q340 THERMOCOUPLE, TWO 3/4 x 1/2 IN
0.87 KPA
REDUCER BUSHINGS, ONE 1/2 x 3/8 IN
REDUCER BUSHING, AND NATURAL TO LP
CONVERSION KIT
COMBINATION SCREW AND 1/4
ONE 3/4 x 1/2 IN REDUCER BUSHING AND
0.87 KPA
NATURAL TO LP CONVERSION KIT.
FULL RATE: COMBINATION SCREW AND 1/4 TWO 3/4 x 1/2 IN; ONE 1/2 x 3/8 IN. REDUCER
0.87 KPA;
BUSHINGS/ADAPTERS
STEP
SETTING:
0.22 KPA
0.87 KPA
80
MLP $
306.64
405.39
405.39
815.21
VR8200 Continuous Pilot Dual Automatic Combination Gas Valves
Combination gas controls for use in 24 VAC, gas-fired, standing pilot appliances with capacities from 20 to 200 cfh. Both include: 1/2”
x 3/8” reducer bushing; 39369014 bag assembly—3/4” straight flange with O ring, screws and wrench; Q340 (39”) thermocouple with
adapters; and 393691 Natural to LP gas conversion kit. VR8200A2132 does not contain the thermocouple. The VR8200A2124 does.
•
•
•
•
•
•
•
•
Control includes safety shutoff, a manual valve, two automatic operators, servo pressure regulator and pilot adjustment.
Compact size.
Provide two automatic valves.
Solenoid-operated first automatic valve opens on thermostat call for heat; closes when call for heat ends.
Diaphragm-operated second automatic valve opens under control of regulator; closes if gas or power supply is interrupted.
Meet codes requiring dual safety shutoff.
All adjustments, wiring connections and pilot outlet are accessible from top of control.
Adjustable servo regulator effectively maintains almost constant gas output pressure under wide fluctuations in
gas supply pressure.
• Compatible with ECO connector.
• VR8200 controls replace the following Honeywell and competitive combination gas controls for applications requiring a minimum
capacity of 20 cfh and a maximum capacity of 200 cfh.
— Honeywell V800A and VR800A models
— White Rodgers 36C03/01 series
— Robertshaw 7000BER (700-400) series
— Robertshaw 7200BER (720-400) series
— ITT B57 and B59 series
— Essex SX242N
Approv al Bodies:
American Gas Association Design certified: File No. L2025006.
Canadian Gas Association Design certified: File No. L2025006.
Underwriters Laboratories Inc. component recognized: File No. MH5323.
Lite-Rite (Off-Pilot-On) lighting sequence.
Mounting: 0° to 90° in any direction from the upright position of gas control knob, including vertically.
Body Pattern: Straight-through with 1/2" inlets and outlets.
Pilot Gas Outlet: Compression fitting for 1/4” OD tubing.
Pressure Tapping: 1/8" NPT with plug
Pressure Rating: 1/2 PSI [3.5 kPa] inlet pressure.
Ambient Temperature Range: VR8200A: 0°F to 175°F [-18°C to +79°C].
Electrical Data:
Supply Voltage: 24 VAC, 60 Hz.
Wiring Connections: Combination screw and 1/4" male quick-connects.
Thermostat Heat Anticipator Setting: 0.5 A.
SOURCE 1 PART NO.
GAS TYPE
S1-VR8200A2124
NAT
S1-VR8200A2132
NAT
AMPS @
PRESSURE
24 VAC/60 SETTING MAIN
HZ MAIN
0.5
3.5
0.5
3.5
CAPACITY
INLET
NPTI
OUTLET
NPTI
PIPE IN DIM
MLP $
130,000 BTU/HR; 20,000 BTU/HR
MINIMUM
130,000 BTU/HR; 20,000 BTU/HR
MINIMUM
1/2
1/2
4.125
208.00
1/2
1/2
4.125
185.93
81
VR8204 Intermittent Pilot Dual Automatic Combination Gas Valves
Combination gas controls for use in 24 VAC, gas-fired intermittent pilot appliances with capacities from 20 to 200 cfh.
• Controls include manual valve, two automatic operators, servo pressure regulator and pilot adjustment.
• Use with S86F,H; S8600F,H and S8610 control modules.
• Compact size.
• Provide two automatic valves.
• Solenoid operated first automatic valve opens on thermostat call for heat; closes when call for heat ends.
• Diaphragm operated second automatic valve opens under control of regulator; closes if gas or power supply is interrupted.
• Meet codes requiring dual safety shutoff.
• Natural to LP gas conversion kits are available, but not included.
• All adjustments and wiring connections are accessible from top of control.
• VR8204 controls replace the following Honeywell and competitive combination gas controls for applications requiring a minimum
capacity of 20 cfh and a maximum capacity of 200 cfh.
— Honeywell VR8440
— White Rodgers 36E36/38
— Robertshaw 7100DER (700-070)
Approv al Bodies:
American Gas Association Design certified: File No. L2025006.
Canadian Gas Association Design certified: File No. L2025006.
Mounting: 0° to 90° from the upright position of gas control knob, including vertically.
Body Pattern: Straight-through with 1/2" inlets and outlets.
Pressure Tapping: 1/8" NPT with plug.
Pressure Rating: 1/2 PSI [3.5 kPa] inlet pressure.
Pilot Gas Outlet: Compression fitting for 1/4" OD tubing.
Ambient Temperature Range:
VR8204A,C: 0°F to 175°F [-18°C to +79°C].
VR8204M: -40°F to +175°F [-40°C to +79°C].
Electrical Data:
Supply Voltage: 24 VAC, 60 Hz.
Wiring Connections: 1/4" male quick-connects.
Thermostat Heat Anticipator Setting: 0.5A.
On-Off lighting sequence.
PRESSURE
REGULATOR
SETTING
SOURCE 1 PART NO.
GAS TYPE
S1-VR8204C1019
NAT
AMPS @ 24 STEP
VAC/60 HZ
MAIN
0.5
.9
FULL
3.5
CAPACITY AT 1 IN. P.D. INLET NPTI OUTLET
NPTI
150,000
1/2
PIPE IN
DIM.
MLP $
4.1
267.36
1/2
VR8205A Direct Ignition Dual Automatic Combination Gas Valves
Combination gas control for use with hot surface/ direct spark sy stems in 24 VAC, gas-fired appliances with
capacities from 20 to 200 cfh. Control includes manual valve, two automatic operators, and servo pressure regulator. Used with
S89E,F and S87C,D Control Modules. Provides dual-seated safety shutoff. Solenoid operated first automatic valve opens on
thermostat call for heat; closes when call for heat ends. Diaphragm operated second automatic valve opens under control of the
regulator; closes if gas or power supply is interrupted. Meets codes requiring dual safety shutoff. Adjustments and wiring connections
are accessible from top of the control. American Gas Association and Canadian Gas Association design certified.
On-Off lighting sequence.
Mounting: 0° to 90° in any direction from the upright position of the gas control knob, including vertically.
Body Pattern: Straight-through.
Includes: 1/2” x 3/8” reducer bushing; 39369014 bag assembly—3/4” straight flange with O ring, screws and
wrench; and 393691 Natural to LP gas conversion kit.
SOURCE 1 PART NO.
GAS TYPE
S1-VR8205A2024
NAT
AMPS @ PRESSURE RATING
24
MAIN
VAC/60
HZ MAIN
0.5
3.5 KPA
82
CAPACITY AT 1 IN. P.D.
INLET
NPTI
OUTLET
NPTI
PIPE IN
DIM.
MLP $
150,000 BTU/HR MAX
1/2
1/2
4.1
203.29
VR8300A Dual Standing Pilot Gas Valve
Combination gas control for use in 24 VAC, gas-fired, standing pilot appliances with capacities from 30 to 300 cfh.
Features:
• Controls include safety shutoff, manual valve, two automatic operators, pressure regulator and pilot adjustment.
• Compact size.
• Diaphragm-operated second automatic valve opens under control of regulator; closes if gas or power supply is interrupted.
• Meets codes requiring dual safety shutoff.
• Standard and slow opening natural gas models include natural to LP gas conversion kit; LP to natural gas conversion kit also
available.
• All adjustments, wiring connections and pilot outlet are accessible from top of control.
• Adjustable servo regulator effectively maintains almost constant gas output pressure under wide fluctuations in
gas supply pressure.
• LITE-RITE (OFF-PILOT-ON) lighting sequence.
Specifications:
Type: Single Stage
Ignition Type: Standing Pilot
Type of Gas: Natural
Body Pattern: Straight through with integral tapping; with flange
Opening Characteristics (standard, step): Standard
Pressure Regulator setting (psi): 3.5” W.C.
Pressure Regulator setting (kPa): 0.87 kPa
Electrical Connections: 1/4” male quick-connects
Frequency: 60 Hz
Anticipator Setting: 0.7 A
Temperature Range (F): 0°F to 175°F
Temperature Range (C): -18°C to +79°C
Approv als: American Gas Association IAS AGA Design Certified: File No. L2025006; Canadian Gas Association CGA Design
Certified: File No. L2025006; Underwriters Laboratories Inc UL Component Recognized.
NO.
SIZE
S1-VR8300A3500 1/2 IN. x 3/4 IN.
S1-VR8300A4508 3/4 IN. x 3/4 IN.
CAPACITY @ 1 IN P.D.
MLP $
190,000 BTU/HR; 30,000 BTU/HR MINIMUM
ONE 3/4 x 1/2 IN. REDUCER BUSHING 393691 NATURAL TO LP GAS CONVERSION KIT
TWO 3/4 x 1/2 IN. REDUCER BUSHING 393691 NATURAL TO LP GAS CONVERSION KIT
233.07
254.79
83
VR8304 Dual Intermittent Pilot Gas Valve
Combination gas control for use in 24 VAC, gas-fired, intermittent pilot appliances with capacities from 30 to 415 cfh.
Features:
• Controls include safety shutoff, manual valve, two automatic operators, pressure regulator and pilot adjustment.
• Use with S86F,H; S860D; S8600F,H; S8610 and S90A,B Control Modules.
• Compact size.
• Diaphragm-operated second automatic valve opens under control of regulator; closes if gas or power supply is interrupted.
• Meet codes requiring dual safety shutoff.
• Standard and slow opening natural gas models include natural to LP gas conversion kit; LP to natural gas conversion kit also
available.
• All adjustments, wiring connections and pilot outlet are accessible from top of control.
• Adjustable servo regulator effectively maintains almost constant gas output pressure under wide fluctuations in gas supply
pressure.
• ON-OFF lighting sequence.
Specifications:
Type: Single Stage
Ignition Type: Intermittent Pilot
Body Pattern: Straight-through
Opening Characteristics (standard, step): Standard
Pressure Regulator setting (psi): 3.5” W.C.
Pressure Regulator setting (kPa): 0.87 kPa
Electrical Connections: 1/4” male quick-connects
Frequency: 60 Hz
Temperature Range (F): -40°F to +175°F
Temperature Range (C): -40°C to +79°C
Approvals: American Gas Association IAS AGA Design Certified: File No. L2025007; Canadian Gas Association CGA Design
Certified: File No. L2025007; Underwriters Laboratories Inc UL Component Recognized.
NO.
SIZE
S1-VR8304M3509 1/2 IN. x 3/4 IN.
S1-VR8304M4507 3/4 IN. x 3/4 IN.
CAPACITY @ 1 IN. P.D.
MLP $
ONE 3/4 x 1/2 IN. REDUCER BUSHING 393691 NATURAL TO LP GAS CONVERSION KIT
TWO 3/4 x 1/2 IN. REDUCER BUSHING 393691 NATURAL TO LP GAS CONVERSION KIT
264.89
270.57
VR8345 Universal Electronic Ignition Combination Gas Control
Features:
• For use with direct spark ignition, hot surface ignition or intermittent pilot ignition in 24 VAC, gas-fired appliances, with capacities
from 30 to 415 cfh.
• For use with natural or manufactured gas or LP gas. Includes converter kit to adapt from natural to LP gas.
• Control includes: manual valve, two automatic operators, pressure regulator (3.5" WC), pilot adjustment, pilot plug and ignition
adapter, two 3/4” x 1/2” NPT reducer bushings and one 1/2” x 3/8” NPT bushing.
• Replaces virtually any IP, HSI or DSI gas control.
• Clearly marked, keyed terminal block allows quick attachment of wires and IP/DSI/HIS jumper.
• Internal inlet screen blocks contaminants in gas line from entering valve.
Body Pattern: Straight-through with 3/4” x 3/4” inlet and outlet.
Dimensions: 5-3/8” H, 4-1/16” W, 2-11/16” D (135 mm H, 104 mm W, 69 mm D)
Approv als: AGA Design Certified: File number L2025007; CGA Design Certified: File number L2025007.
SOURCE 1 PART NO.
IGNITION
VOLT
OPENING
INLET-OUTLET SIZE
FUEL
MLP $
S1-VR8345M4302
DIRECT/ INTERMITTENT PILOT
24
STANDARD
3/4 IN. x 3/4 IN.
NAT/LP
268.79
84
Conversion Kits
SOURCE 1 PART NO.
DESCRIPTION
S1-391936
LP TO NATURAL GAS CONVERSION KIT;
INCLUDES REGULATOR SPRING,
O-RING, SCREW AND CAP.
NATURAL GAS TO LP CONVERSION KIT,
INCLUDING REGULATOR SPRING,
O-RING, SCREW AND CAP
S1-391937
MLP $
V800 FAMILY, V400 FAMILY, VS820, VS821 STANDARD AND SLOW.
20.96
V400 FAMILY, V800 FAMILY, VS820, VS821 STANDARD AND SLOW
13.11
SV9501 SmartValveTM System Gas Valve
TM
The SmartValve System Controls provide intermittent pilot gas ignition sequencing, pilot flame sensing, and both pilot and main gas
control functions in a single control. They are directly compatible with the Q3450 or Q3480 intermittent pilot burners used with the
original controls on many gas fired heating appliances.
Features:
• Suitable for a wide range of gas-fired appliances including residential furnaces, rooftop furnaces, residential boilers, unit heaters,
infrared heaters, space heaters and commercial cooking units.
• Replaces some SV9500, SV9501 and SV9502 SmartValve™ System models.
• Ignition sequence includes timed trial for ignition.
• Pilot gas outlet
Specifications:
Flame Sense: Electrode
Ignition System Type: Intermittent hot surface pilot ignition
Ignition Sequence: Intermittent pilot
Ignition Source: Pilot
Ignition Trials to Lockout: Continuous retry
Ignition Trial Time: 90 sec.
Flame Failure Response Time: 1.6 sec. @ 3 μA
Prepurge: None
Body Pattern: Straight-through
Opening Characteristics: Standard opening
Ambient Temperature Range: –40° to +175°F (–40° to +79°C)
Frequency: 60 Hz/50 Hz
Approv als: American Gas Association IAS, IAS Design Certified: C2030017
CAPACITY
SOURCE 1 PART NO.
S1-SV9501M2528
GAS
TYPE
NAT
PRESSURE REGULATOR
SETTING
3.5” WC (0.87 KPA)
PRESSURE RATINGS
MAXIMUM
MINIMUM
1/2 PSI (3.45 KPA)
3
0.6 M3/HR
200 FT /HR (5.7
M3/HR) 150 FT3/HR AT
1” P.D. (20 M3/HR AT
INLET
NPT
1/2”
OUTLET
NPT
1/2”
MLP $
485.61
1” P.D.)
SV9502H2522 System Control
The SmartValve® System Controls provide easy field replacement of a wide range of SV9500, SV9501, SV9502 and SV9602
SmartValve System models. Gas appliance manufacturers use these models in many types of gas fired heating appliances including
central furnaces, residential boilers, rooftop furnaces, commercial cooking appliances, and unit heaters. These controls provide
intermittent pilot gas ignition sequencing, pilot flame sensing, and both pilot and main gas control functions in a single control. They
are directly compatible with the Q3450 or Q3480 Intermittent Pilot burners used with the original controls on the appliance.
Features:
• Suitable for a wide range of gas-fired appliances including residential furnaces, roof-top furnaces, residential boilers, unit heaters,
infrared heaters, space heaters and commercial cooking units.
• Replaces SV9500, SV9501 and SV9502 controls as noted below.
• Ignition sequence includes timed trial for ignition.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-SV9502H2522
SMART VALVE SYSTEM CONTROL
514.14
85
GAS PRESSURE REGULATORS
Maxitrol Gas Pressure Regulator
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-325-3-1/2
S1-325-5A-1/2
S1-325-5A-3/4
MAXITROL 1/2" GAS PRESSURE REGULATOR - 10 PSI
MAXITROL 1/2" GAS PRESSURE REGULATOR USE WITH R325E1
MAXITROL 3/4" GAS PRESSURE REGULATOR - 10 PSI
43.14
116.39
113.89
POWER GENERATORS, THERMOCOUPLES, HOT SURFACE IGNITERS
Honeywell Q340A Thermocouples
Q340A thermocouples sense the pilot flame on gas-fired heating systems. T he pilot flame heats the tip of the thermocouple,
producing a temperature differential between it and the base to generate a small amount of DC power, measured in millivolts.
Features:
• Push-in clip, split nut, and adapter assembly for easy pilot burner installation.
• Spade or quick-connect terminals available for millivolt gas control connections.
• Male nut connector for Pilotstat® safety control power units.
• Available in a variety of lead lengths.
• Adapter and Push In clip included
SOURCE 1 PART NO.
S1-Q340A1066
S1-Q340A1074
S1-Q340A1090
S1-Q340A1108
LEAD
LENGTH
18 IN.
24 IN.
36 IN.
48 IN.
CONNECTION TYPE
RESISTANCE
MLP $
11/32 32 MALE CONNECTOR NUT
11/32 32 MALE CONNECTOR NUT; PUSH IN KIT
0.02 OHMS
0.02 OHMS
0.02 OHMS
0.02 OHMS
18.29
19.89
21.29
23.07
White Rodgers Universal Replacement Thermocouples
High temperature stainless steel element specially designed for universal replacement.
Features:
• Stainless steel element construction for prolonged thermocouple life.
• Each kit individually enclosed in plastic.
• Universal adapter fittings included with each kit for replacing thermocouple in most types of pilot burners.
• Visible instructions for quick, easy installation.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-H06E-18
S1-H06E-24
S1-H06E-30
S1-H06E-36
S1-H06E-48
S1-H06E-72
UNIVERSAL 18” THERMOCOUPLE
10.68
11.29
11.93
12.36
14.36
21.71
White Rodgers 750 Millivolt Power Generator
Provides power for 750 millivolt self-generation control systems.
Features:
• For replacement of similar screw-in type generators now in field or for use with type E31- 12 pilot burner.
• G01A-332 has 36 inch armored cable leads with split-spade terminals.
• PG9 Adapter included with each G01A-332.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-G01A-332
S1-G01A-512
750 MV W/36” LEADS (ARMORED CABLE) AND PG9 ADAPTER
750 MV W/36” LEADS (FIBERGLASS) WITH F SPADE CLIPS
97.21
81.82
86
Source 1 Silicon Carbide Igniters
Source 1's Norton hot surface igniters are made of high purity recrystallized silicon carbide to provide reliable ignition in a variety of
heating systems.
• Replaces Carrier, Lennox, Rheem, T rane,and others
• Can reach ignition temperature(s) in 17 seconds
• 18-gauge nickel chrome lead wires enclosed with high-temperature fiberglass insulation
• Compare to Robertshaw R 41-400 Series
See following table for cross-reference information.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-HSI-401
S1-HSI-402
S1-HSI-403
S1-HSI-404
S1-HSI-405
S1-HSI-406
S1-HSI-407
S1-HSI-408
S1-HSI-409
S1-HSI-410
S1-HSI-411
S1-HSI-412
S1-HSI-414
S1-HSI-418
KIT,IGNITER,HOT SURFACE, 271A, 4-1/2" LEADS
KIT,IGNITER,HOT SURFACE, 271W, 19" LEADS
KIT,IGNITER,HOT SURFACE, 271M, 5-1/2" LEADS
KIT,IGNITER,HOT SURFACE, 271D, 10-1/2" LEADS
KIT,IGNITER,HOT SURFACE, 271Y, 4-1/2" LEADS
KIT,IGNITER,HOT SURFACE, 271N, 4-1/2" LEADS
KIT,IGNITER,HOT SURFACE, 271NM, 4-1/2" LEADS
KIT,IGNITER,HOT SURFACE, 271NM, 5-1/4" LEADS
KIT,IGNITER, HOT SURFACE, 271NM, 5.25" LEADS
42.71
41.46
40.89
42.07
42.71
40.89
40.89
40.89
40.89
40.89
41.29
41.46
43.68
42.71
HOT SURFACE IGNITER CROSS REFERENCE
Exact replacements are designated by an *. All other igniters are f unctional replacements.
OEM
P ART NO.
AMAN A
B133610 2
D99182
1004160 1
AMERIC AN APPLI ANCE
271B
AMERIC AN RO AD EQUIPMEN T
201W
AR MS TRONG AIR
38322B0 01
CARRIER CORPOR ATION
LH33ZS001A
LH33ZS002
COLEMAN/EVCON
1474-051
1474-052
COMFORT ZONE
150114-0 4-01
DETROIT R ADI AN T
201D
DMO INDUSTRIES
20834
DORNBACK FURNACE
271W
DUCANE
2001520 1
ENERCO TECH
10399
GOODMAN
B140100 9
B140101 5S
B140101 8S
B140101 5
HUPP INDUSTRIES
9050
INTERCITY
1009604
MAJES TIC
75-92-10 4
75-92-10 5
ME TZGER
201N
201W
SOURCE 1
P ART NO.
S1-HSI-401
S1-HSI-401*
S1-HSI-401*
S1-HSI-406*
S1-HSI-402
S1-HSI-402
S1-HSI-409*
S1-HSI-409*
S1-HSI-402
S1-HSI-402
S1-HSI-406
S1-HSI-405
S1-HSI-402
S1-HSI-402
S1-HSI-409*
S1-HSI-402
S1-HSI-412*
N/A
S1-HSI-418
S1-HSI-418
S1-HSI-402
S1-HSI-412*
S1-HSI-402
S1-HSI-402
S1-HSI-402
S1-HSI-402
OEM
P ART NO.
MODINE
5H75032
MOR-FLO
3200580
3200618
3210401
NORDYNE
1051410 00
632-0880
632-0770
FC007
902661
FC047K
903110
NORTON
201
201A
201D
201J
201K
201L
201N
201R
201W
201Y
271
271A
271P
271M
271N
271NM
271W
271Y
PERFECTION SCHWANK
108803- G1
RAYP AK
600915
RHEEM
62-22441 -01
62-22441 -01
62-22868 -82
SP-1097 2
87
SOURCE 1
P ART NO.
N/A
S1-HSI-406*
S1-HSI-402
S1-HSI-406
S1-HSI-402
S1-HSI-402
S1-HSI-402
N/A
N/A
N/A
N/A
S1-HSI-403
S1-HSI-401
S1-HSI-405
S1-HSI-406
S1-HSI-402
S1-HSI-402
S1-HSI-402
S1-HSI-402
S1-HSI-402
S1-HSI-406
S1-HSI-403
S1-HSI-401
S1-HSI-405
S1-HSI-406
S1-HSI-402
S1-HSI-412
S1-HSI-402
S1-HSI-406
S1-HSI-406
S1-HSI-403
S1-HSI-408
S1-HSI-402
S1-HSI-411*
N/A
OEM
P ART NO.
ROBERTS GORDON
9043430 0
9043660 0
SMITH HB
50018
SNYDER GENER AL
1380672
1380680
1380654
TR ANE CO MP AN Y
B138196 P01
B144676 P02
B340039 P01
340039P 01
IGN21
IGN23
IGN26
IGN26
IGN30
IGN30
3033 KIT
VIESSMAN
9302-094
W AYNE HOME EQUIP MENT
62821-00 1
62821-00 2
WELL MCLAIN
511-330- 139
511-330- 188
511-330- 193
WILLIAMSON
9050
YORK INTERN ATION AL
025-2776 6-000
025-2777 4-000
025-2904 3-000
025-2905 0-000
SOURCE 1
P ART NO.
S1-HSI-409
S1-HSI-402
S1-HSI-405*
S1-HSI-409*
S1-HSI-409*
S1-HSI-403
S1-HSI-403
S1-HSI-407*
S1-HSI-408*
S1-HSI-402
S1-HSI-402
S1-HSI-409*
S1-HSI-403
S1-HSI-407*
S1-HSI-403
N/A
S1-HSI-405*
S1-HSI-402
S1-HSI-402
S1-HSI-409*
S1-HSI-406*
S1-HSI-403
S1-HSI-402
S1-HSI-405*
S1-HSI-405*
S1-HSI-405*
S1-HSI-405*
Source 1 Timesaver Silicon Nitride Igniters
Compare to White-Rodgers 21D64-2 and Honeywell Q3200U1004, Replaces over 100 Silicon Carbide igniters
Kit Includes:
Features:
• Robust Ignitor Design—for Longer Life and Fewer
• Silicon Nitride Igniter with 15.5" Leads
Callbacks
• One “Universal” Mounting Bracket and Screw
• Mounting Adaptor Bracket
• Universal Bracket Fits Most Furnaces—
• Reduces Inventory, Easy to Install
• 2 Ceramic Wire Nuts
• 3-Year Warranty
• Updated Manufacturer Cross-Reference
Specifications
• Instruction Booklet
• Electrical Rating
Input 102-132 VAC, 60Hz
Max. Load Current 3.0 A @ 132 VAC, 25 degrees C
• Timing Rating 17 Seconds Minimum
SOURCE 1 PART NO.
DESCRIPTION
S1-HSI-SN1
Manufacturer
Amana
American Road
Equipment
Arco Air
Armstrong Air
Carlin
Carrier/Bryant/
Payne*
Claire Bros.
Coleman
Comfort Maker
Detroit Radiant
DMO Ind.
Dornback Furnace
Ducane
Enerco Tech
Evcon
Evcon Coleman
Goodman
HB Smith
Heil
Honeywell
Hupp Industries
OEM Part Number
10735003A, 20165703S,
20165703, 201657-03,
Model 601
201W
1096048, 1380680
38322B001
87197S
LH33ZS001, LH33ZS001A,
LH33ZS004
C-238, C-242
1474-051, 1474-052
1096048
201D
20834
271W
20015201
10399
1474-051, 1474-052
025-32625-000
0230K00001, B1401009,
B140109S, B1401015S,
B1401018, B1401018S
50018
1096048
Glowfly (Q3200U)
9050
MLP $
UNIVERSAL NITRIDE HOT SURFACE UPGRADE KIT
Manufacturer
Intercity
Majestic
OEM Part Number
1009604, 1096048
75-92-104, 75-92-105
Metzger
Modine
Mor-Flo
Nordyne
201N, 201W
5H76032A
3200618, 511-330-193
105141000, 632-0770,
632-0880
Norton/
201, 201D, 201J, 201K,
St. Gobain
201L, 201M, 201N, 201R,
201W, 271, 271M, 271N,
271NM, 271P, 271W
Raypak
600915
Rheem/RUUD 62-22441-01, 62-22868-02,
Roberts Gordon 62-22868-82, 62-22868-93
90434300, 90436600
Robertshaw
41-402, 41-403, 41-404,
41-405, 41-407, 41-408,
41-409, 41-410, 41-411,
41-412, 41-413, 41-414,
41-418
Snyder General
1380654, 1380672,
1380680
Superior
94851
Fireplace
Tempstar
1096048
Trane
340039P01, B138196P01,
B144676P01, B144676P02,
B340039P01, IGN00023,
IGN00026, IGN00030,
IGN00034
Universal Brackets Included to Replace These Ceramic Block-Style Silicon Carbide Igniters
88
Manufacturer
Viessman
Wayne Home
Equipment
Weil McLain
White LB
White-Rodgers
Williamson
York/Luxaire
47.36
OEM Part Number
9302-094
62821-001, 62821-002
511-330-139, 511-330-188,
511-330-190, 511-330-193
120-07549
767A-301, 767A-303,
767A-306, 767A-310,
767A-311, 767A-350,
767A-353, 767A-354,
767A-357, 767A-361,
767A-364, 767A-365,
767A-366, 767A-370,
767A-371, 767A-372,
767A-373, 767A-375,
767A-376, 767A-377,
767A-378, 767A-382,
767A-383, 767A-384
9050
025-27766-000,
025-27774-000,
025-29043-000,
025-29050-000
2532625000
* For Carrier sealed combustion f urnaces, y ou must
use
Assembly 6 and reuse the existing orange gasket
POWER GENERATORS, PILOT BURNERS & PILOT CONTROLS
Honeywell Pilot Burner for Natural Gas
Nonprimary-aerated combination pilot burner and igniter. Used with the S86, S860, S8610, or S8670 in intermittent pilot systems.
Features:
• Includes pilot burner with bracket, ceramic insulated Kanthal flame rod/spark igniter and ground strap.
Specifications:
Direction of Front Tip: (F) Front
Tip Style: Single
Aeration: Non-primary
Leadw ire Temperature Ratings (C): Max. at electrode tip: 968°C
Includes: 1/4" cc inlet fitting and mounting adapter
SOURCE 1 PART NO.
MOUNTING BRACKET COMPRESSION FITTING
LENGTH
B
0.78 IN.
S1-Q345A1305
ORIFICE
MLP $
BCR-18 (0.018 IN.)
66.43
Honeywell Q313 Thermopile Generator
Q313 Thermopile Generator contains multiple thermocouples connected in series to increase the millivoltage output. The power
generated is sufficient to operate an automatic millivolt gas control system, independent of any outside power source.
Features:
• Push-in clip, split nut, and adapter assembly for easy pilot burner installation.
• Spade or quick-connect terminals available for millivolt gas control connections.
• Male nut connector for Pilotstat® safety control power units.
• Available in a variety of lead lengths.
Specifications:
Voltage 750 mV
Connection Type Spade Terminals
Open Circuit Output (mV) 600 mV to 750 mV
Temperature Ratings (F) Hot Junction 1400 F
Temperature Ratings (C) Hot Junction 760 C
Temperature Ratings (F) Cold Junction 780 F
Temperature Ratings (C) Cold Junction 416 C
Used With Q314, Q324, Q327, Q377, Q379,
Q382 Pilot Burners
SOURCE 1 PART NO.
LEAD LENGTH
RESISTANCE
MLP $
S1-Q313A1055
S1-Q313A1139
S1-Q313A1170
47 IN. (1194 MM)
35 IN. (889 MM)
35 IN (889 MM)
2.90 OHM
2.89 OHM
2.89 OHMS
1/2 IN. THERMOPILE ATTACHING NUT
PUSH-IN CLIP
PG9 ADAPTER AND 1/2 IN. THERMOPILE ATTACHING NUT
112.61
104.14
114.86
Honeywell Q314A Pilot Burners
Non primary-aerated, insert orifice type pilot burner for main burner ignition. Used with Q309, Q340, Q340 thermocouples or Q313
thermopiles.
Features:
• 1/4" Compression fitting.
• B style mounting bracket.
• Single tip style.
• Includes special mounting bracket with screws to convert B bracket to A bracket
SOURCE 1 PART NO.
FRONT TIP DIRECTION
MLP $
S1-Q314A4586
S1-Q314A6094
S1-Q314A6102
FRONT
LEFT
RIGHT
59.43
59.43
59.43
89
IGNITION MODULES & INTEGRATED FURNACE CONTROLS
Honeywell S8610U Universal Intermittent Pilot Module
Provides electronic control of most intermittent pilot ignition systems used on gas-fired furnaces, boilers and other heating
appliances.Provides ignition sequence, flame monitoring and safety shutoff (max. 90 sec.) for intermittent pilot central furnaces and
heating appliances.
Provides 100 percent pilot gas shutoff if pilot fails to light; after 6-minute delay, trial for ignition is repeated. Ignition trial/delay
sequence is repeated until the appliance lights or call for heat is removed.
For use with natural or LP gas.
For use in single rod or dual rod/remote sense applications.
Includes relay contacts for use with any intermittent pilot gas control string with maximum 1.0A pilot or 2.0A main valve rating;
Honeywell VR8204, VR8304 or VR8345M combination gas control recommended.
Functional equivalent of S86, S90, S8600 and S8610 modules.
Includes cable adapters to allow field replacement of both Honeywell and competitive controls without replacing existing cable.
Improved enclosure design protects internal circuitry from moisture or dust accumulation. Includes remote reset, and automatic vent
damper plug. Replaces most of the following intermittent pilot modules:
— Honeywell S86, S90, S8600 and S8610
— Robertshaw SP715, SP715A, SP735, SP735A, SP735L
— Johnson GSA, G60, G65, G67, G600, G770 Refer to S8610 specification sheet for a complete list of model numbers.
APPROVAL BODIES:
American Gas Association Design certified.
Canadian Gas Association Design certified.
Underw riters Laboratories Inc. Component recognized.
AMBIENT TEMPERATURE RATING: –40°F to +165°F [–40°C to +74°C].
FLAME FAILURE RESPONSE TIME: 0.8 sec. At 1.0 mA flame current.
WIRING CONNECTIONS: 1/4" male quick connect terminals, including ignition terminal (3/16" male quick-connect sense terminal).
ELECTRICAL RATINGS: Voltage and Frequency – 24V (nominal), 60Hz. Current rating – 0.2A
RUNNING
INRUSH
PILOT
1.0A
10.0A
MAIN
2.0A
20.0A
NOTE: Maximum ambient temperature is 175°F [79°C] if main valve relay load is 1.0A or less.
THERMOSTAT HEAT ANTICIPATOR SETTING: 0.2A plus pilot valve rating plus main valve rating. Spark Generator Output – 13 kV
peak at 25 pf load.
SOURCE 1 PART NO.
MLP $
S1-S8610U3009
300.07
White Rodgers Mercury Flame Sensors
The mercury flame sensor is a mechanical device that proves the existence of an acceptable pilot flame. It converts the heat of a pilot
flame to motion which is used to open and close a set of electrical contacts, and consists of a bulb, capillary, diaphragm, snap-switch
mechanism, and mercury-fill. When the bulb is heated by a pilot flame, the mercury is vaporized causing pressure in the capillary and
diaphragm. Movement of the diaphragm causes the snap-switch to open one set of contacts, and close a second set. These contacts
control the pilot valve and the main valve.
Features:
• Bulb styles are designed to fit with various OEM applications.
• Adapter fittings to allow use of these mercury flame sensors with competitive burners are packed with controls identified with an
asterisk(*).
• A.G.A. Design certified and C.G.A. Certified.
• Maximum temp. 1450°F at bulb tip.
SOURCE 1 PART NO.
DESCRIPTION
S1-3049-115*
S1-3049-18
S1-3049-64*
S1-3098-134*
S1-3098-156*
REPLACES BULB STYLES #17 OR #18.
ELEMENT PANEL
LENGTH
TYPE
48”
D
33”
D
48”
D
48”
E
48”
E
BULB
STYLE
#20
#7
#19
#19
#20
MLP $
299.04
299.04
299.04
311.07
299.07
*Adapter fitti ngs packed wi th control.
White Rodgers Pilot Relite Control
Ignition control generates spark pulses to ignite pilot gas. The relite control generates sparks until a pilot flame is sensed between the
electrode and ground. The relite control detects a flame through “flame conduction” (ability of a flame to conduct a current). When
flame current is sensed between the electrode and pilot burner ground, the relite control stops sparking. If the flame is extinguished
during the heat call, the relite control will begin sparking the instant the flame goes out.
Features:
• A.G.A. Design certified and C.G.A. certified.
SOURCE 1 PART NO.
DESCRIPTION
INPUT VOLTAGE
ELECTRICAL RATING
MLP $
S1-5059-23
SPARK PLUG AND 1/4” SPADE CONNECTORS
24 VAC
0.03 AMPS
192.46
90
Honeywell Switching Relay
Provide intermediate switching of a line voltage device from a low voltage controller.
Features:
• Integral transformer provides low voltage power for control circuit.
Specifications:
Application: For switching one line voltage load
Temperature Range (F): 115°F Max. Ambient for 60 Hz
Temperature Range (C): 46°C Max. Ambient for 60 Hz
Electrical Ratings -Primary Voltage: 120V
Electrical Connections (Control Circuit): 2-Wire
Approv als: Underwriters Laboratories Inc UL Listed: File no. E4436, Guide no. XAPX; Canadian Standards Association CSA
Certified.
Includes: Integral transformer, enclosure.
Contacts Electrical Ratings (240 VAC): 5.1AFL, 30.6 ALR, 6.0A resistive.
CONTACTS ELECTRICAL RATINGS
SOURCE 1 PART NO.
S1-RA89A1074
SWITCHING
ACTION
SPST
COIL RATINGS
AFL
ALR
RESISTIVE
CURRENT
VOLTAGE
MLP $
10.2
61.2
10.0A
0.4A
24 VAC
160.75
S9200U1000 Hot Surface Ignition Integrated Furnace Control
Universal integrated furnace control replaces multiple single stage field installed hot surface ignition IFC supplied by White Rodgers
and UTEC. Uses 120 VAC igniter. Includes instructions special wire harnesses for easy replacement.
Features:
• Main burner ignition using a 120V hot surface igniter.
• Flame rectification circuit to monitor flame presence.
• Monitoring of system pressure switch, high temperature limit, and rollout functions.
• Appliance operation/safety requirements controlled via microprocessor.
• Control of a standard induction-type circulating fan motor (based on appliance requirements), in response to a conventional low
voltage or EnviraCOM™ thermostat.
• LED system status, performance and diagnostic indication.
• Wire harnesse s provided for simple replacement of most IFCs and integration with most heating and cooling appliances.
• Twinning capability
• EnviraCOM™ communication capability to enable local and/or remote system status, diagnostics, troubleshooting, and HVAC
sy stem control.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-S9200U1000
INTEGRATED FURNACE CONTROL
276.21
S8910U1000 Universal Hot Surface Ignition Module
Universal hot surface ignition module replaces multiple field installed hot surface ignition modules supplied by Honeywell, WhiteRodgers, Robertshaw and Johnson. Uses a 120 VAC igniter. Includes instructions and accessories for easy replacement.
Features:
• Replaces many White-Rodgers, Robertshaw and Honeywell hot surface ignition models.
• For 120 Vac (up to 5.0A) surface igniter (Norton 201/271 or equivalent).
• For local (single rod) or remote (dual rod) rectification type flame sensing.
• Contains easy-to-use instructions plus the accessories required to adapt the existing hot surface ignition module.
• Provides one or three ignition trials (four-second or seven-second trials) per call for heat; prepurge of 32 seconds or less; up to 96
seconds between purge trial times.
• Temperature range is -40 to +175 F (-40 to +79 C).
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-S8910U1000
UNIVERSAL HOT SURFACE IGNITION MODULE
281.36
Universal Silicon Carbide Integrated Ignition Module
The 50A55-843 employs a microprocessor to continually monitor, analyze and control the proper operation of the gas burner, inducer
and fan.
Electrical Ratings at 77°F (25°C):
Input Voltage: 25 VAC 50/60 Hz
Maximum Input Current: at 25 VAC 0.45 amp
Operating Temperature: –40° to 176°F (–40° to 80°C)
Humidity: 5% to 93% relative humidity (non condensing)
SOURCE 1 PART NO.
DESCRIPTION
REPLACES
MLP $
S1-50A55-843
UNIVERSAL SILICON CARBIDE INTEGRATED
IGNITION MODULE
50A55-143, 50A55-285, 50A55-286, 50A55-438
272.89
91
50A65-843 Carbide Non-Integrated Hot Surface Ignition Module
Gas-Fired Non-Integrated Forced-Air Furnaces and Boilers
Features:
• Program Keys for Easy Customization
• Tri-Color LED Indicator for Diagnostics
• Direct and Indirect Flame Sense
Specifications:
Electrical Rating
• Input 18 to 30 VAC, 25 VAC nominal
• Max. Input Current @ 25 VAC; 200mA @ 25°C
Relay Load Settings
• Valve Relay: 1.5 amps @ 25 VAC 60 Hz .6pf
• Ignitor Relay: 6.0 amps @ 120 VAC 60 Hz resistive
Kit Includes:
• Program Keys
• Mounting Hardware
• Double-Sided Foam Back Tape (for ease of installation)
• Extensive Cross-Reference Guide
• Color-Coded Timing Label
• Pre-Printed Hanging Carton
• Instructions in English/Instrucciones en Espanol
SOURCE 1 PART NO.
DESCRIPTION
DIMENSIONS
MLP $
S1-50A65-843
CARBIDE NON-INTEGRATED IGNITION MODULE
4.13 X 4.13 X 1.5
289.79
For Silicon Carbide, Non-Integrated HSI Systems
Replaces ALL White-Rodgers 50E47-xxx modules and virtually all competitive silicon carbide, non-integrated modules.
Features:
• Program Keys for Easy Customization
• Tri-Color LED Indicator for Diagnostics
Electrical Rating
• Max. Input Current @ 25 VAC; 200mA @ 25°C
Relay Load Settings
Valve Relay: 1.5 amps @ 25 VAC 60 Hz .6pf
Ignitor Relay: 6.0 amps @ 120 VAC 60 Hz resistive
SOURCE 1 PART NO.
DESCRIPTION
DIMENSIONS
MLP $
S1-50E47-843
FOR SILICON CARBIDE, NON-INTEGRATED HSI SYSTEMS
4.13" W X 4.13" H X 1.5" D
287.71
Single Stage Carbide and Nitride HSI Systems
Replaces: Virtually All White-Rodgers and Competitive Single Stage Carbide and Nitride HSI Systems – Including Carrier Systems.*
Specifications
Includes:
• Electrical Rating [@ 77°F (25°C)]
• Ignition Control Module – 50M56-843
• Input Voltage: 25 VAC 50/60 Hz
• 12 Quick-Select/Quick-Connect Wiring Harnesses
• Max. Input Current @ 25 VAC: 0.45 amp
• Universal Nitride Ignitor Kit – 21D64-2
Relay Load Ratings
• Installation Instructions and OEM Cross-Reference
• Valve Relay: 1.5 amp @ 25 VAC 50/60 Hz 0.6 pf
• Igniter Relay: 6.0 amp @ 120 VAC 50/60 Hz (resistive)
Features:
• 3 Fan Speeds – Cool, Low Heat & High Heat Speeds • Circulator Relay: 14.5 FLA—25.0 LRA @ 120 VAC
• Color-Coded (Labeled) Thermostat Connection
Flame Current Requirements
• Minimum current to insure flame detection: 1 μa DC*
• System Diagnostics, with Fault Recall (Stored)
• Maximum current for non-detection: 0.1 μa DC*
• Cover Label – Displays Diagnostic Table
• *Measured w/ DC microammeter in flame probe lead
• Red LED Light – Used for Diagnostic Flash Codes
• Low Voltage – Fuse Protection – 3A automotive type Operating Temperature Range
• -40° to 176°F (-40° to 80°C)
• Humidifier & Electronic Air Cleaner Connections
Mounting
• Color LED Indicator for Diagnostics
• Surface mount multi-poise
• Surface mount multi-poise
Timing Specifications (@ 60 Hz)
• Max. Flame Establishing Time: 0.8 sec
• Max. Flame Failure Response Time: 2.0 sec
Gases Approved: Natural, Manufactured, Mixed,
• Liquified Petroleum, and LP Gas-Air Mixtures are
• all approved for use.
Relay Load Rating
• Main Valve Relay: 1.5A @ 25 VAC 60 Hz
Hot Surface Ignition
• 120 VAC
Dimensions
• 5.25" W x 7" H x 1.25" D
SOURCE 1 PART NO.
DESCRIPTION
DIMENSIONS
MLP $
S1-50M56U-843
SINGLE STAGE CARBIDE AND NITRIDE HSI SYSTEMS
5.25" W X 7" H X 1.25" D
319.86
92
FAN & LIMIT CONTROLS
White Rodgers Fan & Limit Controls for Universal Replacement
Single element type for applications with narrow space limitations. Regulates fan or blower operation and acts as high limit safety
control.
Features:
• Designed to be interchangeable with other flush mounted, single element fan and limits.
• Slotted mounting holes for easy installation.
• Long Terminal screws for wiring—Junctions can be made on terminal block.
• Limit switch has “universal” contact structure capable of handling millivolts to 240 VAC.
• Limit switch has adjustable stop to limit maximum setting—Shipped at 200° F (94° C).
• Dial has individual pointers for fan cut-in and cut-out settings.
• Removable solid copper jumper between fan and limit switches.
• Summer fan switch for ventilation without changing control settings. Has same fan and limit switch mechanism.
• C.S.A. Certified and U.L. Recognized.
Specifications and Cross Reference:
VENDOR DESCRIPTIO
TYPE
N
NO.
FAN
5D51
SERIES
LIMIT
RANGE
SWITCH
DIFFERENTIAL
ACTION
FULL
ELECTRICA
L
RATING
50 TO 265° F
CLOSE
ADJUSTABLE
(10 TO 129° 15° F MINIMUM
ON
C)
RISE
100 TO 300° F
OPEN
FIXED 25° F
(38 TO 149°
ON
C)
RISE
SOURCE 1 PART NO.
DESCRIPTION
S1-5D51-35
S1-5D51-78
S1-5D51-90
WITH STANDARD ENCLOSURE
MOTOR
VALVES AND
RATING
RELAYS
(FULL LOAD)
120
240
24 0.3-12V
VAC VAC VAC
DC
HT
14.0A
7.0A
—
—
HTV
10.0A
6.0A
6.0A
1.0A
ELEMENT
LENGTH
5”
11”
8”
MLP $
205.36
205.36
205.36
Direct Spark Non-Integrated Spark Ignition Module
Features:
Electrical Rating
• Max. Input Current: @ 25 VAC: 0.2A + MV @ 25°C
Relay Load Ratings
Main Valve Relay: 25 VAC, 1.5 Amp Max.
Pilot Valve Relay: 25 VAC, 1.5 Amp Max.
SOURCE 1 PART NO.
DESCRIPTION
DIMENSIONS
MLP $
S1-50D50-842
DIRECT SPARK NON-INTEGRATED SPARK IGNITION MODULE
4.13" W X 4.13" H X 1.5" D
285.04
Intermittent Pilot Non-Integrated Spark Ignition Module
Features:
Electrical Rating
• Max. Input Current: @ 25 VAC: 0.2A + MV + PV @ 25°C
Relay Load Ratings
Main Valve Relay: 25 VAC, 1.5 Amp Max.
Pilot Valve Relay: 25 VAC, 1.5 Amp Max.
SOURCE 1 PART NO.
DESCRIPTION
DIMENSIONS
MLP $
S1-50D50-843
INTERMITTENT PILOT NON-INTEGRATED SPARK IGNITION
MODULE
4.13" W X 4.13" H X 1.5" D
285.04
93
Y8610U4001 Intermittent Pilot Retrofit Kit
Intermittent Pilot Retrofit Kit are complete kits converting conventional standing pilot system to intermittent pilot system. For use with
24 Vac gas-fired atmospheric furnaces, boiler and heating appliances.
Features:
• Y8610U kits are for use with natural or LP gas: provides 100 percent pilot gas shutoff if pilot fails to light; after 6-minute delay, trial
for ignition is repeated.
• Ignition trail/delay sequence is repeated until the appliance lights or call for heat is removed
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-Y8610U4001
INTERMITTENT PILOT RETROFIT KIT
546.39
FAN & LIMIT CONTROLS
Honeywell L4064 Fan & Limit Controls
Features:
• Three wiring terminal options available for easy installation: push-in receptacles for stripped wire, female receptacles for 1/4” male
flag connectors, and field add-on screw terminals.
• Super Tradeline models include deluxe case with mounting adapters for easy installation and strain relief bushings to protect wiring
from field abuse.
Specifications:
Application: Turns fan on and off according to plenum temperature. With helical bimetal sensing element. High limit stop
factory set at 200ºF (93ºC). Replaces L4064A,B,E.
Fan-on Range: 65ºF to 215ºF (18ºC to 102ºC
Fan-off Range: 50ºF to 200ºF (10ºC to 96ºC)
Pilot duty: 0.25 A @ 0.25 to 12 Vdc, 2 A @ 24 VAC
Dimensions: 5-3/8”H x 3”W x 2”D (137 mm H x 76 mm W x 51 mm D) excluding element.
Mounting: Rigid bracket
Differential Temperature: 25ºF (14ºC), fixed.
Approv als: UL Listed; CSA Certified.
MAX. AMBIENT TEMPERATURE
RATINGS
SOURCE 1 PART
NO.
HIGH LIMIT TEMPERATURE RANGE
S1-L4064B1451*
ELECTRICAL RATING FAN
ELECTRICAL RATING LIMIT
SWITCH
SENSING
ELEMENT
(AFL)
(ALR)
(AFL)
(ALR)
MLP $
100ºF TO 250ºF (38ºC TO 121ºC)
ELEMENT
INSERTION
LENGTH
11-1/2” (292 MM)
190ºF (88ºC)
350ºF (177ºC)
5” (127 MM)
190ºF (88ºC)
350ºF (177ºC)
S1-L4064B2236
8” (203 MM)
190ºF (88ºC)
350ºF (177ºC)
42 A @ 240
VAC, 84 A @
120 VAC
42 A @ 240
VAC, 84 A @
120 VAC
42 A @ 240
VAC, 84 A @
120 VAC
4 A @ 240
VAC, 8 A @
120 VAC
4 A @ 240
VAC, 8 A @
120 VAC
4 A @ 240
VAC, 8 A @
120 VAC
24 A @ 240
VAC, 48 A @
120 VAC
24 A @ 240
VAC, 48 A @
120 VAC
24 A @ 240
VAC, 48 A @
120 VAC
220.29
S1-L4064B1469*
7 A @ 240
VAC, 14 A @
120 VAC
7 A @ 240
VAC, 14 A @
120 VAC
7 A @ 240
VAC, 14 A @
120 VAC
215.11
208.14
*L4064B models have m anual fan swi tch that overri des fan control to keep fan running continuously.
Honeywell L4064W Fan & Limit Controls
Features:
• Three wiring terminal options available for easy installation:
• push-in receptacles for stripped wire, female receptacles for 1/4-in. male flag connectors, and field add-on screw terminals.
• SUPER TRADELINE models include deluxe case with mounting adapters for easy installation and strain relief bushings to rotect
wiring from field abuse.
APPLICATION
Bimetal heater switch turns fan on Approximately 20 to
90 seconds after Thermostat calls for heat at a cold start.
High limit stop factory-set at 200°f [93°c]. Replaced
L4064T,Y
INCLUDES
Two lead wires with ¼ in. [6 mm] male flag Terminals
attached, two ¼ in. [6 mm] female Quick-connect terminals
for low volt heater Terminal connection, four add-on screw
Terminals, and two jumpers for line voltage Fan and limit
interconnect
INSERTION
SOURCE 1 PART NO.
IN.
MM
MOUNTING
MLP $
S1-L4064W1080*
S1-L4064W1098*
S1-L4064W1106*
5
8
11-1/2
127
203
292
SURFACE OR RIGID BRACKET
326.46
320.57
331.75
*Wi th m anual fan switch to override fan set points and keep fan running continuously.
94
ICM Gas Ignition Modules
ICM293
Features:
• Intermittent Pilot Gas Ignition Control Module
• For use with intermittent pilot boilers, furnaces and other
heating appliances
• Microprocessor-based
• Monitors timing, trial for ignition, flame sensing and
lockout
• Remote flame sensing
• 100% lockout safety feature
• Compatible with LP or Natural Gas
• Status LED for fault codes to aid in troubleshooting
• Replaces: Lennox 30W33 ignition control, Robertshaw
735L (18G91) or 745 (95H04) ignition controls, Johnson
Controls G776 (63K2401, 41K8701, 69J3601) ignition
controls
Specifications:
• Control Voltage: Line 24 VAC (18-30 VAC) 50/60 Hz
• Anticipator Setting: 0.2A plus valve load @ 24 VAC
• Prepurge: 15 seconds
• Trial for Ignition: 85 seconds
• Lockout: 60 minutes
• Flame Failure Response Time: 0.5 seconds
• Status LED: See product label for error codes
• Operating Temperature:
Minimum ambient temperature rating is -40°F (-40°C)
Maximum ambient rating when used with 2.0A main
valve is
165°F (74°C)
• Relative Humidity: 0% to 95% non-condensing
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ICM293
LOW COST, INTERMITTENT PILOT GAS IGNITION CONTROL
372.71
ICM Furnace Control Modules
Features:
• Twinning compatible with another ICM board-identical model
Furnace Fan Blower Control
SOURCE 1 PART NO.
DESCRIPTION
OUTPUTS
TIME DELAYS
MLP $
S1-ICM280
INDUCER FAN OUTPUTS, HOT SURFACE
IGNITOR OUTPUT FLAME SENSOR INPUT
GAS VALVE OUTPUT 18–30 VAC
FAN: 2 HP @ 240 VAC INDUCER FAN: 7A @
250 VAC GAS VALVE: 1A @ 24 VAC IGNITOR:
5A @ 120 VAC
HEAT ON: 30 SEC. HEAT OFF: 90, 120, 150
SEC. COOL OFF: 60 SEC.
214.46
Replaces:
SOURCE 1 PART NO.
S1-ICM280
GOODMAN
B1809906/08/10/13/135
UTEC
1012-933D
TEXAS INSTRUMENTS
41F-5
95
WHI TE RODGERS
50T 35-730, 50T 35-743
CARRIER
—
Gas Valve, Ignitor, Blower Motor, Inducer, Humidifier & Air Cleaner Controls
SOURCE 1 PART NO.
DESCRIPTION
VOLTAGE
TIME DELAYS
MLP $
S1-ICM281
MODEL SELECTION OF 80+ AND 90+
FURNACE OPERATION
HEAT BLOWER ON: 40 SEC. HEAT BLOWER
OFF: 90, 135, 180, 225 SEC. FAN (LOW)
ON/OFF: 1 SEC. COOL ON: 5 SEC. COOL OFF:
90 SEC.
234.43
S1-ICM282
INCLUDES ADAPTER HARNESS
LINE RANGE: 98–132 VAC @ 60 HZ IGNITER:
5A @ 120 VAC COOL BLOWER: 10A, 2HP, 240
VAC HEAT: 5A 1/2HP, 240 VAC NDUCER
MOTOR: 4A, FLA-8.0 LRA @ 120 VAC GAS
VALVE: 1.5A @ 30 VAC
LINE RANGE: 98–132 VAC @ 60 HZ IGNITER:
5A @ 120 VAC COOL BLOWER: 10A, 2HP, 240
VAC HEAT: 5A 1/2HP, 240 VAC NDUCER
MOTOR: 4A, FLA-8.0 LRA @ 120 VAC GAS
VALVE: 1.5A @ 30 VAC
HEAT BLOWER ON: 60 SEC. HEAT BLOWER
OFF: 90, 120, 150, 180 SEC. FAN (HEAT)
ON/OFF: 1 SEC. COOL ON: 2 SEC. COOL OFF:
90 SEC. JUMPER JW2 UNCUT; 5 SEC.,
JUMPER JW2 CUT
339.46
Replaces:
SOURCE 1 PART NO.
S1-ICM281
GOODMAN
—
UTEC
—
TEXAS INSTRUMENTS
—
WHI TE RODGERS
—
—
—
—
—
S1-ICM282
CARRIER
CESO110057-00/01/02
HK42FZ004/007/
008/009/011/013/016, 325878-751
ICM284
Features:
• Controls vent motor, blower control, hot surface ignitor and gas valve
• Microprocessor based, Designed for 100% gas shutoff in case of ignition failure
• Monitors timing, trial for ignition, flame sensing and lockout
• Diagnostic LEDs aid in testing/troubleshooting
Specifications:
Electrical
Env ironmental
• Line Voltage Range: 208 VAC @ 60Hz
• Ambient Temperature: Operating: -40°C to 80°C
Storage: -40°C to 85°C
• Ignitor: 5A resistive @ 208 VAC
• Humidity: 5% - 95% R.H. (non-condensing) at +55°C
• Cool Blower: 30 A, 2 HP, 240 VAC
• Heat Blower: 10 A, ½ HP, 250 VAC
Replaces:
• York: S1-03101280000
• Inducer Motor: 4A, 208 VAC
• Gas Valve: 4A @ 24 VAC
• Compressor: 5A resistive @ 24 VAC
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ICM284
S1-ICM286
LOW COST, DIRECT REPLACEMENT FURNACE CONTROL BOARD
MODULE,CNTRL,FURNACE,GOODMAN
717.71
107.71
ICM Furnace Control Board
ICM288
Replacement for Rheem 62-24084-82 control boards
Specifications:
Voltage Range: Line 98-132 VAC @ 60HZ
Ignitor: 5A, 120 VAC
Cool Blower: 10A, 2HP, 240 VAC
Heat: 5A, 1/2 HP, 250 VAC
Inducer Blower: 4A, 120 VAC
Gas Valve: 1A, 24 VAC
Humidifier Motor: 0.5A, 24 VAC
Electronic Air Cleaner: 1A, 120 VAC
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ICM288
FURNACE CONTROL BOARD
277.14
96
Features:
ICM287
Features:
• Controls inducer and blower control
• Microprocessor based
• Designed for 100% gas shutoff in case of ignition failure
• Monitors timing and gas valve
• Diagnostic LEDs aid in testing/ troubleshooting
Specifications:
Electrical
Env ironmental
• Line Voltage Range: 120 VAC @ 60Hz
• Ambient Temperature: Operating: -40°C to 80°C
Storage: -40°C to 85°C
• Control Voltage: 24 VAC @ 60 Hz
• Humidity: 5% - 95% R.H. (non-condensing) at +55°C
• Cool Blower: 30A resistive @ 120 VAC
• Heat Blower: 10A resistive @ 120 VAC
• Inducer Blower: 10A resistive @ 120 VAC
Replaces:
• Goodman: B18099-04
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ICM287
253.79
ICM289
Features:
• Low cost, direct replacement board for Lennox
• Microprocessor based design
• Controls inducer fan motor, blower fan and monitors limit switches
• Functions with all 24 VAC thermostats
Specifications:
• Voltage Range: Line (98 to 132 VAC) @ 60 Hz
• Cool Blower: 20A @ 120 VAC
• Heat Blower: 20A @ 120 VAC
• Inducer Motor: 5A @ 120 VAC
• Cool Blower On Delay: 1 second
• Cool Blower Off Delay: 1 second
• Heat Blower On Delay: 45 seconds
• Heat Blower Off Delay: 90, 150, 210, 270 seconds
Replaces:
• Lennox: Replaces all BCC1, BCC2 and BCC3 circuit boards, including models LB-53622A, BCC2-2REV8, 35K77, 35K7701, LB90089A, 65K29, 65K2901, LB-50709BD, LB-65126A, LB-89859, LB-87086A, LB-87086, LB-63622AA, LB-90676A, 40L8801,
30H6701, 48K98, 48K9801, 45K48, 45K4801, 78J61, 78J6101, 68H08.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ICM289
282.04
Continuous Retry Ignition Control
ICM290A
Replacement for popular models, including Honeywell S8610U-3009
Specifications:
Control Voltage: Line 24V (18-30 VAC), 50/60Hz
Anticipator Setting: 0.3A plus valve load @ 24VAC
Trial for Ignition: 15 or 90 sec (switch selectable)
LEDs:
- Green Status LED provides sy stem status and error codes
- Yellow Flame LED indicates flame presence and flame strength
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ICM290A
CONTINUOUS RETRY IGNITION CONTROL
274.96
97
Features:
ICM291
Features:
• Low cost, direct replacement for Carrier: LH33WP003A
• Direct Spark Ignition (DSI) control board
• Controls combustion, blower and indorr fan motors; spark ignitor; and the gas valve
• Monitors timing, trial for ignition, flame sensing and lockout
• 100% lockout safety feature
• Status LED for fault codes to aid in troubleshooting
Specifications:
• Control Voltage: 24 VAC (18-30 VAC), 60Hz
• Line Voltage: 208/230 VAC, 60Hz
Timing:
• Pre-Purge
• Trial for
Ignition
• Retry Period
• Lockout
• Post-Purge
:
:
:
:
:
45 seconds
5+2 seconds
Every 20 seconds for 15 minutes
Manual reset
45 seconds
Input:
• Power: RT and C
• Thermostat Interface: R,W, and G
• Safety Switches: RS, LS, and CS
• Combustion Motor Hall Effect Sensor
• Flame Sensing
Outputs:
• Spark
• Gas Valve: GV
• Combustion Motor: CM
• Blower Motor: BM
• Indoor Fan Motor: IFO
LED Indicators:
Red LED: Steady ON-normal operation; Flashing-fault codes
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ICM291
LOW COST, DIRECT REPLACEMENT FOR CARRIER: LH33WP003A
355.82
ICM Furnace Control Board
ICM2801
Replacement for York/Evcon 7990-319P control boards
Specifications:
• Line Voltage Range: 98 to 132 VAC @ 60Hz
• Ignitor: 5A @ 120 VAC
• Cool Blower: 10A, 2 HP, 240 VAC
• Heat: 5A, 1/2 HP, 250 VAC
• Inducer Motor: 4A FLA, 8A LRA @ 120 VAC
• Gas Valve: 1A @ 24 VAC
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ICM2801
FURNACE CONTROL BOARD
259.96
98
Features:
ICM292
Features:
• Low cost, direct replacement for Rheem: 62-24140-04
• Direct Spark Ignition (DSI) control
• Controls inducer motors, air cleaner (if equipped), humidifier (if equipped), spark ignitor, and the gas valve
• Monitors timing, trial for ignition, system switches, flame sesning, and lockout
• 100-percent lockout safety feature , Compatible with LP or Natural gas
• LED indication for status and fault codes to aid in troubleshooting
Specifications:
• Control Voltage: 24 VAC (18-30 VAC), 60Hz
• Line Voltage: 115 VAC, 60Hz
Timing:
Pre-Purge:
Trial for Ignition:
Retries:
Lockout:
Post-Purge:
30 seconds
7 seconds
Two groups of two, 30 second delay within the group, and 3 minute delay between groups
1-hour
90, 120, 160 and 180 seconds
Inputs:
• Power: 24 VAC and COM
• Thermostat Interface: R,W, Y, and G
• System Switches: Vent pressure and limit switches
• (main and over-temperature switches in series)
• Flame Sensing
• Heat Blower OFF Delay (miniature slide switch set)
Outputs:
• Spark
• Gas Valve: GV
• Inducer Draft Motor: IDM
• Blower Motor: FAN, COOL and HEAT speeds
• Electric air Cleaner: EAC
• Humidifier Relay: HUM , Heat/Cool Relay: H/C
LED Indicators:
• Power, Green LED: PWR
• Status, Green LED: OK
• Flame Status, Yellow LED: FLAME
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ICM292
LOW COST, DIRECT REPLACEMENT FOR RHEEM: 62-24140-04
301.50
ICM2804
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ICM2804
236.00
Note: This board functions identically as the CES0110074-00 and the CES0110074-01. It is a direct replacement of the CES0110074-01. When replacing the
CES0110074-00 some quick connectors have to be changed or added. EAC-1 and EAC-2 must have 1/4” connectors. COM, SEC-1 and SEC-2 must have
3/16” connectors.
99
ICM2805
Features:
• Controls gas valve, inducer draft motor, circulating blower and hot surface ignitor
• Monitors timing, trial for ignition, flame sensing, lockout, plus pressure, rollout and limit switches.
• Microprocessor-based precision, Twinning compatible with another ICM2805A furnace control
• Diagnostic LEDs aid in testing and troubleshooting
• Replaces: Nordyne 903106-Kit (for use with G3, G4, G5, G6, M2 and M3 furnace modules)
Specifications:
• Voltage Range: Line (98 to 132 VAC) @ 60Hz
• Ignitor: 5A, 120 VAC
• Cool Blower: 10A, 2HP, 240 VAC
• Heat: 5A, ½ HP, 250 VAC
• Inducer Blower: 4A, 120 VAC
• Gas Valve: 1A, 24 VAC
• Humidifier Motor: 0.5A, 24 VAC
• Electronic Air Cleaner: 1A, 120 VAC
Replaces:
Nordyne 903106-KIT (for use with G3, G4,
G5, G6, M2,and M3 furnace modules)
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ICM2805
LOW COST, FORM, FIT,AND FUNCTIONAL REPLACEMENT
246.96
ICM Spark Ignition Controls
ICM295
Features:
• For use with intermittent pilot boilers, furnaces or other heating appliances
• Microprocessor-based precision, Compatible with LP or Natural Gas
• Continuous spark until pilot flame established
• Replaces Carrier LH33WZ510 and comparable ignition controls
Specifications:
• Control Voltage: Line 24 VAC (18-30 VAC) @ 50/60Hz
• Prepurge: 0 or 10 seconds (sy stem dependent)
• Retries: Continuous
• Operating Temperature: -40°F (-40°C) to 75°C (176°F)
• Spark Frequency: 15Hz for 90 seconds, 10Hz thereafter
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ICM295
LOW COST, FORM FIT FUNCTION REPLACEMENT
127.14
Intermittent Pilot Ignition Control
ICM2901
Replacement for popular models, including York 025-27762-700 and JCI G770RJA-1 series controls
Specifications:
Prepurge: None
Trial for Ignition: 85 seconds
Flame Failure Response Time: 0.5 seconds
Retry: None
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ICM2901
INTERMITTENT PILOT IGNITION CONTROL
252.36
ICM2902
Replacement for popular models, including Lennox 30W33 and JCI G776RGD-14 series controls
Specifications:
Prepurge: 15 seconds
Lockout: 60 minutes
Flame Failure Response Time: 2 seconds
LED: See product label for error codes
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ICM2902
257.46
100
Intermittent Pilot Ignition Control
ICM294
Replacement for popular models, including York 025-27762-700 and JCI G770RJA-1 series controls
Specifications:
Prepurge: None
Flame Failure Response Time: 0.5 seconds
Retry: None
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ICM294
282.14
ICM Spark Ignition Controls
ICM296
Features:
• For use with intermittent pilot boilers, furnaces or other heating appliances
• Microprocessor-based precision
• 100% safety lockout
• Replaces Carrier LH33WZ512 and comparable ignition controls requiring 100% safety lockout
Specifications:
• Control Voltage: Line 24 VAC (18-30 VAC) @ 50/60Hz
• Prepurge: None
• Lockout: 5-6 minutes
• Retries: None
• Operating Temp.: -40°F (-40°C) to 75°C (176°F)
• Relay Contact Rating: 1 amp @ 24 VAC
• Trail for Ignition: 90 seconds
• Flame Failure Response Time: 0.8 sec. max.
• Spark Frequency: 60 Hz
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ICM296
LOW COST, FORM FIT FUNCTION REPLACEMENT
214.79
101
Multi-Stage Carbide and Nitride HSI Systems
21M51U-843 For 3-Speed PSC Motors
Replaces: White-Rodgers 50M51-242 and All 50M61-XXX’s Two-Stage HSI Systems with 80V or 120V Ignitor.
Includes:
• Ignition Control Module
• Universal 120V Nitride Ignitor Kit – 21D64-2
Features:
• 120 VAC Ignitor Output
• 120 VAC Two-Speed Inducer Output
• 120 VAC Humidifier Output
• 120 VAC Electronic Air Cleaner Output
• 120 VAC 3-Speed PSC Circulator Output
• 2-Stage Gas Valve Output
• Fuse Protection – 3 Amp
• Furnace Status LED – Tri-Color (Green, Red and Amber)
• Heat Fan OFF Delay (Dipswitch Selectable)
• Fan ON Delay for Cooling
• Auto Second Stage Delay (Dipswitch Selectable Mode)
• Historical Fault Retrieval by Pushbutton
• YLO, Y, W1, W2, R, G, C, TWIN Terminals
• Pressure Switch Inputs and Monitoring
• Flash Microprocessor with Non-Volatile Memory
• Flame Current Measurement Points
Specifications:
Electrical Ratings [@ 77°F (25°C)]
Input Voltage: 24 VAC, 60 Hz (Class II transformer req’d)
Nom. Input Current @ 24 VAC: 530 mA + MV
Relay Load Ratings
Gas Valve Relays: 1.5 amps @ 24 VAC, 60 Hz
Inducer Relays: 2.2 FLA – 3.5 LRA @ 120 VAC
Circulator Relays: 14.5 FLA – 25.0 LRA @ 120 VAC
Humidifier Load: 1.0 amp max. @ 120 VAC
Electronic Air Cleaner Load: 1.0 amp max. @ 120 VAC
Ignitor Relay: 4.0 amps max. @ 132 VAC, 60 Hz
Minimum current to insure flame detection: 0.3 μa DC*
Maximum current for non-detection: 0.1 μa DC*
Maximum allowable leakage resistance: 100 M ohms
*Measured w/ DC microammeter in the flame probe lead
Operating Temperature Range
-40° to 175°F (-40° to 80°C)
Humidity Range
5% to 93% relative humidity (non-condensing)
Flame Failure Response Time: 2.0 sec. max.
Gases Approved
Natural, Manufactured, Mixed, LP, and LP/Air Mixtures
Dimensions
5.25" W x 8" H x 1.25" D
SOURCE 1 PART NO.
DESCRIPTION
DIMENSIONS
MLP $
S1-21M51U-843
MULTI STAGE CARBIDE AND NITRIDE HSI SYSTEMS
5.25" W X 8" H X 1.25" D
457.11
21V51U-843 For Variable Speed Motors
Replaces: All White-Rodgers 50V51-XXX’s and 50V61-XXX’s Two-Stage HSI Systems with 80V or 120V Ignitor.
Includes:
• Ignition Control Module
• Wiring Harnesse s for Amana/Goodman
• Universal 120V Nitride Ignitor Kit – 21D64-2
Features:
• 120 VAC Ignitor Output
• 120 VAC Two-Speed Inducer Output
• 120 VAC Humidifier Output
• 120 VAC Electronic Air Cleaner Output
• 2-Stage Gas Valve Output
• 16-Pin Variable Speed Circulator Output
• OEM Application – Dipswitch Selectable
• Fuse Protection – 3 Amp
• Furnace Status LED – Tri-Color (Green, Red and
Amber)
• CFM LED – (Green)
• Heat Fan OFF Delay (Dipswitch Selectable)
• Fan ON Delay for Cooling
• Auto Second Stage Delay (Dipswitch Selectable Mode)
• Historical Fault Retrieval by Pushbutton
• YLO, Y, W, W2, R, G, C, O, BK/DS/Dehum Terminals
• Pressure Switch Inputs and Monitoring
• Flash Microprocessor with Non-Volatile Memory
• Flame Current Measurement Points
Specifications:
Electrical Ratings [@ 77°F (25°C)]
Input Voltage: 24 VAC, 60 Hz (Class II transformer req’d)
Nom. Input Current @ 24 VAC: 595 mA + MV
Relay Load Ratings
Gas Valve Relays: 1.5 amps @ 24 VAC, 60 Hz
Inducer Relays: 2.2 FLA – 3.5 LRA @ 120 VAC, 60 Hz
Humidifier Load: 1.0 amp max. @ 120 VAC, 60 Hz
Elect. Air Cleaner Load: 1.0 amp max. @ 120 VAC, 60 Hz
Ignitor Relay: 4.0 amps max. @ 132 VAC, 60 Hz
Minimum current to insure flame detection: 0.3 µa DC*
Maximum current for non-detection: 0.1 µa DC*
Maximum allowable leakage resistance: 100 M ohms
*Measured w/ DC microammeter in the flame probe lead
Operating Temperature Range
-40° to 175°F (-40° to 80°C)
Humidity Range
5% to 93% relative humidity (non-condensing)
Flame Failure Response Time: 2.0 sec. max.
Gases Approved
Natural, Manufactured, Mixed, LP, and LP/Air Mixtures
Dimensions
5.25" W x 8" H x 1.25" D
SOURCE 1 PART NO.
DESCRIPTION
DIMENSIONS
MLP $
S1-21V51U-843
MULTI STAGE CARBIDE AND NITRIDE HSI SYSTEMS
5.25" W X 8" H X 1.25" D
457.11
102
ELECTRIC HEATING COILS
Supco Electric Heat Coil Kit
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-DH500
S1-DH506
S1-DH534
ELECTRIC HEATING COIL KIT, 5KW, 240V
20.82
24.39
30.50
HEAT SEQUENCERS
Model 24A34 Electric Heat Sequencers
Direct replacement for most fan/heat sequencind functions. Terminal markings are equivalent to competitive types and allow
one wiring method for various sources of sequencers.
Features:
• Replaces Honeywell, Klixon (Texas Instruments), MARS, TOD, GEMLINE types.
• Solid-state reliability.
• Ambient rated from -50 to +165°F.
• 24V input control.
• Multi-poise mounting.
• Any contacts (except M1 and M2) can be used as auxiliary contacts.
• Double quick-connect terminals for combination loads.
• U.L. Component recognized.
24A34-15
Normally Open Contacts 1-3
• Used in heat pump air handler applications.
• Provides a delay off to the blower motor in cooling mode.
• Single pole double throw.
Specifications:
Electrical Ratings
Single Load Contact Ratings (All Models):
RESISTIVE (NON-INDUCTIVE)
VAC
WATTS
AMPS
120
3000
25.0
MOTOR RATINGS (INDUCTIVE)
FULL LOAD
10.0A (14.0A FOR 24A3415)
5.0A (7 FOR 24A34-15)
3.0A
PILOT DUTY
LOCKED ROTOR
60.0A (72 FOR 24A34-15)
125 VA
240
6000
25.0
30.0A (42 FOR 24A34-15)
480
6000
12.5
18.0A
Combined Load Rating (All Models):
30A @ 240 VAC — TOTAL; 23 A Non-inductive + 7 FLA/42 LRA Inductive.
ON TIME — Elapsed time to make contacts after heater is energized (Min. to Max.).
OFF TIME — Elapsed time to break contacts after heater is de-energized (Min. to Max.).
125 VA
480 VA
SOURCE 1 PART NO.
TIMINGS
SWITCHES
MLP $
S1-24A34-1
S1-24A34-14
S1-24A34-15
S1-24A34-2
S1-24A34-3
S1-24A34-4
S1-24A34-5
S1-24A34-6
1
4
1
1
1
1
2
2
1
5
1
1
2
2
3
4
12.61
39.18
31.64
12.61
14.86
14.86
22.71
25.07
TIMINGS
ON
SOURCE 1
P ART NO.
S1-24A3 4-1
S1-24A3 4-2
S1-24A3 4-3
S1-24A3 4-4
S1-24A3 4-5
S1-24A3 4-6
S1-24A3 4-14
S1-24A3 4-15
OFF
M1- M2
M3- M4
M5- M6
M7- M8
M9- M10
1-20
—
—
—
—
30-90
—
—
—
—
—
—
—
—
—
—
1-20**
—
—
1-110**
30-90**
1-110
1-110**
1-160**
—
1-160
M1- M2
M3- M4
40-110
—
—
—
40-110**
—
—
1-110**
M5- M6
M7- M8
M9- M10
—
1-30
—
—
—
—
—
—
—
—
—
—
1-30**
1-110
1-110**
1-160**
1-60 (ON 1-3)
—
1-160
75-95 (OFF 1-3)
*M1-M2 and M3-M4 are always first switches to turn ON and last to turn OFF. All other switches are random ON and random OFF.
†24A34-14 Switch contacts designated F1-F2 instead of M1-M2.
**These contacts switch simultaneously.
Note: Underwriters Laboratories requires a fan interlock circuit to insure the blower remains operating whenever more than one sequencer is used.
The fan interlock should be the M1-M2 contacts of the second or third sequencer. All M1-M2 contacts are wired to the blower motor so that any
sequencer that is energized will keep the blower ON.
103
SNAP DISC LIMIT SWITCHES
White Rodgers Adjustable Snap Disc Fan & Limit Controls
This adjustable Snap Disc Thermostat allows you to set the temperature set point to match your specific needs which simplifies
inventory.
Features:
• 1/4” quick connect terminals are standard.
• Reduces inventory while providing coverage for a wide range of temperature applications.
• Replaces the majority of fixed disc thermostats now on heating equipment and various appliances.
• 2 adjustable fan control models replace 7 fixed snap disc models.
• 4 adjustable limit control models replace 10 fixed snap disc models.
Accessories: Adapter plates (order separately.): F6-1798 1 per pack.
Typical Electrical Ratings
RESISTIVE
MOTOR RATING
PILOT
VAC
NON-INDUCTIVE)
DUTY
FULL LOAD
LOCKED ROTOR
120
240
SOURCE 1 PART NO.
25.0 A
25.0 A
14.0 A
10.0 A
DIFFERENTIAL
S1-3F05-1
TEMPERATURE
RANGE
90 TO 130° F
S1-3F05-2
72.0 A
60.0 A
125 VA
125 VA
FUNCTION
ACCESSORIES
20° F
SWITCH
ACTION
SPST
FAN CONTROLS (CLOSE ON RISE)
140 TO 180° F
20° F
SPST
FAN CONTROLS (CLOSE ON RISE)
S1-3L05-1
135 TO 175° F
40° F
SPST
LIMIT CONTROLS (OPEN ON RISE)
S1-3L05-10
135 TO 175° F
20° F
SPST
S1-3L05-13
250 TO 290° F
40° F
SPST
S1-3L05-2
175 TO 215° F
40° F
SPST
S1-3L05-3
210 TO 250° F
40° F
SPST
INCLUDES
THERMOSTAT AND
TAB-TO-SCREW
TERMINALS
INCLUDES
THERMOSTAT AND
TAB-TO-SCREW
TERMINALS
INCLUDES
THERMOSTAT AND
TAB-TO-SCREW
TERMINALS
INCLUDES
THERMOSTAT AND
TAB-TO-SCREW
TERMINALS
INCLUDES
THERMOSTAT AND
TAB-TO-SCREW
TERMINALS
INCLUDES
THERMOSTAT AND
TAB-TO-SCREW
TERMINALS
INCLUDES
THERMOSTAT AND
TAB-TO-SCREW
TERMINALS
“THERM-O-DISC”
NUMBER
74T12-310708
MLP $
74T12-310709
34.86
74T11-310710
34.86
74T11-310724
33.96
74T11-310730
34.86
74T11-310711
34.86
74T11-310712
34.86
34.86
Limit Controls - Manual Reset
FIXED TEMPERATURE SETTINGS
SOURCE 1 PART NO.
CUT-IN
CUT-OUT
SWITCH ACTION
S1-3L02-160
S1-3L02-170
S1-3L02-180
S1-3L02-190
S1-3L02-200
MANUAL RESET
MANUAL RESET
MANUAL RESET
MANUAL RESET
MANUAL RESET
160° F (71° C)
170° F (77° C)
180° F (82° C)
190° F (88° C)
200° F (93° C)
OPEN ON RISE
OPEN ON RISE
OPEN ON RISE
OPEN ON RISE
OPEN ON RISE
“THERM-O-DISC” PART
NO.
60T15-330534
60T15-330535
60T15-330536
60T15-330537
60T15-330538
MLP $
21.46
21.46
21.46
21.46
22.00
Spdt Controls
TERMINAL 1 & 3
TERMINAL 1 & 2
SOURCE 1 PART NO.
CUT-OUT
CUT-IN
CUT-IN
CUT-OUT
S1-3L03-140
S1-3L03-190
140° F (60° C)
190° F (88° C)
120° F (49° C)
170° F (77° C)
140° F (60° C)
190° F (88° C)
120° F (49° C)
170° F (77° C)
SWITCH
ACTION
SPDT
SPDT
“THERM-O-DISC”
PART NO.
60T13-611015
60T13-611014
Electrical Ratings
ELECTRICAL R ATING ( AC)
FOR TYP E NUMBERS
3L01
3L02
1 & 2 CLOSE ON RISE
3L03
1 & 3 OPEN ON RISE
MO TOR R ATING (FULL LOAD)
120 V AC
240 V AC
10.0 A
5.0 A
10.0 A
5.0 A
5.8 A
2.9 A
10.0 A
5.0 A
104
120/240 V AC
277 V AC
25.0 A
21.6 A
25.0 A
21.6 A
—
—
25.0 A
21.6 A
PILOT DUTY
120/240/277 V AC
125 VA
125 VA
125 VA
125 VA
MLP $
20.57
20.57
SNAP DISC LIMIT SWITCHES
White Rodgers Snap Disc Fan Controls
Fan Controls
SOURCE 1 PART NO.
CUT-IN
CUT-OUT
SWITCH ACTION
“THERM-O-DISC” PART NO.
MLP $
S1-3F01-110
S1-3F01-120
S1-3F01-130
S1-3F01-140
S1-3F01-150
S1-3F01-160
S1-3F01-180
S1-3F01-200
S1-3F01-350
110° F (43° C)
120° F (49° C)
130° F (54° C)
140° F (60° C)
150° F (66° C)
160° F (71° C)
180° F (82° C)
200° F (93° C)
350° F (177° C)
90° F (32° C)
110° F (43° C)
115° F (46° C)
120° F (49° C)
130° F (54° C)
140° F (60° C)
160° F (71° C)
180° F (82° C)
320° F (160° C)
CLOSE ON RISE
CLOSE ON RISE
CLOSE ON RISE
CLOSE ON RISE
CLOSE ON RISE
CLOSE ON RISE
CLOSE ON RISE
CLOSE ON RISE
CLOSE ON RISE
60T12-610044
60T12-610046
60T12-610047
60T12-610049
60T12-610050
60T12-610064
60T12-610065
60T12-610066
60T12-610067
13.43
13.43
13.11
13.43
13.43
13.11
13.11
13.11
13.11
Limit Controls-Manual Reset
SOURCE 1 PART NO.
CUT-IN
CUT-OUT
SWITCH ACTION
“THERM-O-DISC” PART NO.
MLP $
S1-3L01-120
S1-3L01-130
S1-3L01-140
S1-3L01-150
S1-3L01-165
S1-3L01-170
S1-3L01-180
S1-3L01-190
S1-3L01-200
S1-3L01-230
S1-3L01-250
S1-3L01-300
S1-3L01-350
110° F (43° C)
115° F (46° C)
100° F (38° C)
110° F (43° C)
125° F (52° C)
130° F (54° C)
140° F (60° C)
150° F (66° C)
160° F (71° C)
190° F (88° C)
210° F (99° C)
250° F (121° C)
310° F (154° C)
120° F (49° C)
130° F (54° C)
140° F (60° C)
150° F (66° C)
165° F (74° C)
170° F (77° C)
180° F (82° C)
190° F (88° C)
200° F (93° C)
230° F (110° C)
250° F (121° C)
300° F (149° C)
350° F (177° C)
OPEN ON RISE
OPEN ON RISE
OPEN ON RISE
OPEN ON RISE
OPEN ON RISE
OPEN ON RISE
OPEN ON RISE
OPEN ON RISE
OPEN ON RISE
OPEN ON RISE
OPEN ON RISE
OPEN ON RISE
OPEN ON RISE
60T11-610000
60T11-61002
60T11-610006
60T11-610009
60T11-610069
60T11-610012
60T11-610013
60T11-610015
60T11-610016
60T11-610021
60T11-610023
60T11-610026
60T11-610068
13.11
13.43
13.43
13.43
13.11
13.43
13.43
13.11
13.43
13.11
13.43
13.11
13.11
SPECIFICATIONS
Electrical Ratings
MODEL
3F01, 3F02
MO TOR R ATING (FULL LOAD)
120V AC
240V AC
10.0A
5.0A
120/240V AC
277V AC
25.0A
21.6A
PILOT DUTY
120/240/277V AC
125 VA
OIL BURNER PROTECTORELAYS
Honeywell R8184G Protectorelay Oil Burner Control
Provides automatic, nonrecycling control of an intermittent ignition oil burner system.
APPROVAL BODIES: Component recognized by Underwriters Laboratories Inc. Certified by Canadian Standards Association.
APPROXIMATE DIMENSIONS: 4 in. [108 mm] wide, 4 in. [111 mm] high, 2 in. [64 mm] deep.
AMBIENT TEMPERATURE RANGE: -40 F to 130 F [-40 C to 54 C].
THERMOSTAT ANTICIPATOR SETTING: 0.2 A.
ELECTRICAL RATINGS: Voltage and Frequency – 120 V, 60 Hz.
• Controls oil burner, oil valve (if desired) and the ignition transformer in response to a call for heat.
• Solid state flame sensing circuit.
• LED on terminal strip indicates system lockout. Remote lockout indication available on some models.
• External button to manually reset safety switch after lockout.
• Manual trip lever opens safety switch for system maintenance. Mounts on standard 4 x 4 in. junction box or directly on burner
housing.
• C554A Cadmium Sulfide Flame Detector and 24 VAC thermostat required.
Load Relay Contacts (A)
MOTOR RATING 120 VAC 240 VAC
FULL LOAD
7.4
3.7
LOCKED ROTOR
44.4
22.2
Ignition Rating – 360 VA (in addition to above motor rating).
SOURCE 1 PART NO.
SAFETY SWITCH TIMING
MLP $
S1-R8184G4009
45 SECONDS
192.46
105
OIL BURNERS & FUEL PUMPS
Parts For Beckett AFG Oil Burners
SOURCE 1 PART NO.
DESCRIPTION
ITEM
BONNET CAPACITY
MLP $
S1-52633074001
SINGLE STAGE PUMP
10
55,000 BTU to 125,000 BTU
177.39
* Includes Gasket
OIL NOZZLES
Danfoss Nozzles For AFG Oil Burners
Features:
• Meets ISO 9001 International standards
• Atomizes fuel oil in burners with capacities from .40 GPH to 3.0 GPH
• Nozzles stamped with spray pattern, capacity and angle
• Atomization pressure is 100 psi
SOURCE 1 PART NO.
DANFOSS PART NO.
S1-52635399000
S1-52635624000
S1-52635628000
S1-52635629000
S1-52635630000
S1-52635631000
S1-52635632000
S1-52635633000
030H6523
030F7529
030H8514
030H6516
030H8516
030H8518
030H6520
030H8528
CAPACITY
GPH
1.20
1.65
.65
.75
.75
.85
1.00
1.50
SPRAY
ANGLE
60°
70°
80°
60°
80°
80°
60°
80°
CONE SHAPE
MLP $
HOLLOW
SOLID
HOLLOW
HOLLOW
HOLLOW
HOLLOW
HOLLOW
HOLLOW
8.18
8.18
12.82
12.82
12.82
7.86
7.14
12.82
CAD CELL RELAYS & FLAME DETECTORS
White Rodgers 668 Series Kwik-Sensor Cad Cell Relays
Replaces intermittent ignition Kwik-Sensor Cad cell relays on oil burner systems with 15, 30 or 45 second safety timing. Certain types
have unique Signal-Lite feature which glows whenever safety lockout occurs.
Features:
• Grey enclosure.
• 120 VAC, 60 Hz standard input voltage.
• 24 VAC control voltage.
• Full 10 FLA, 60 LRA, 120 VAC rating on motor relay contacts.
• Ignition transformer rating 360 VA (3.0A).
• 10” useable leads.
• Mounts to 4” x 4” junction box.
• Line voltage safety switch eliminates burner run-on in event motor relay contacts weld closed.
• Solid state flame detection circuitry is not affected by vibration or high or low ambient temperatures. Suitable for use from -40 to
150° F (-40 to 66° C).
• Screw terminals for low voltage connections provide positive contact.
• Recycles upon momentary flame failure or power interruption.
SOURCE 1 PART NO.
SAFETY
TIMING
THERMOSTAT
TYPE
S1-668-401
S1-668-430
S1-668-451
S1-668-501
S1-668-601
45 SEC.
45 SEC.
45 SEC.
30 SEC.
15 SEC.
2-WIRE
2 OR 3 WIRE *
2-WIRE
2-WIRE
2-WIRE
THERMOSTAT
SAFETY
ANTICIPATOR LOCK-OUT LIGHT
SETTING
0.4A
0.4A
0.4A
0.4A
0.4A
NO
YES
NO
NO
NO
MANUAL
LOCK-OUT
LEVER
INTEGRAL
TRANSFORMER
NO
YES
NO
NO
NO
NO
NO
40VA
NO
NO
TIME
START
FAN
SWITCH
NO
F*-B
C-W
NO
NO
MLP $
176.57
266.57
292.71
240.71
240.71
* 3-w ir e series 10.
† Models w ith external transformer have safety sw itch contacts in motor relay (low voltage) circuit.
White Rodgers Flame Detectors
Solid state el ectronic fl am e detector which util i zes li ght i ntensi ty to sense the presence of a fl am e in oil burni ng heating equipm ent.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-956-154
UNIVERSAL FLAME DETECTOR WITH 6 BRACKETS. 60” LEADS.
41.00
106
OIL BURNER PROTECTORELAYS
R8184M Protectorelay Oil Burner Control
Provides control of an intermittent ignition oil burner and power for a low voltage cooling control circuit.
APPROVAL BODIES: Component recognized by Underwriters Laboratories Inc.
APPROXIMATE DIMENSIONS: 6” [152 mm] H, 4” [121 mm] W, 2” [64 mm] D.
AMBIENT TEMPERATURE RANGE: 32°F to 115°F [0°C to 46°C].
ELECTRICAL RATINGS: Transformer – 40 VA.
• Primary voltage – 120 V, 60 Hz; secondary voltage (open circuit) – 27 V, 60 Hz
• Ignition is on whenever the burner is on (intermittent ignition — also called constant ignition), Solid state flame sensing circuit.
• External button to manually reset safety switch after lockout.
• Enclosed safety switch must be manually reset after safety shutdown.
• Y and G terminals for connection of cooling equipment.
• Integral 40 VA transformers.
• Mounts on standard 4” x 4" junction box.
• C554A Cadmium Sulfide Flame Detector and a 24 VAC thermostat required.
Load Contacts (A)
MOTOR RATING
120 VAC
240 VAC
FULL LOAD
7.4
3.7
LOCKED ROTOR
44.4
22.2
Ignition rating – 360 VA (in addition to above motor rating).
Power Consumption – 6.5 W running.
SOURCE 1 PART NO.
SAFETY SWITCH TIMING
S1-R8184M1002
45 SECONDS
MLP $
THERMOSTAT ANTICIPATOR
SETTING
0.2 AMPS
310.29
HONEYWELL AQUASTAT® CONTROLS
Immersion type controls for limiting or regulating temperatures of liquids in boilers or tanks.
Features:
• Horizontal or vertical insertion of the sensing element, Direct or well immersion of the sensing element.
• Tradeline models include well adapter and tube of heat-conductive compound.
• Select models have wells.
Specifications:
Approv als: UL Component Recognized: File number
Electric Ratings (full load): 8.0 A @ 120 VAC;5.1 A @
MP466, Vol. Sec. 1, Guide number MBPR2; CSA
240 VAC
Certified: File number LR95329-1; AGA Certified: L4006A
Electrical Ratings (locked rotor): 48.0 A @ 120
Case Dimensions: 5-5/8”H x 2”W x 2-1/8”D (143 mm H x
VAC;30.6 A @ 240 VAC
51 mm W x 54 mm D)
Electrical Ratings (milliv olt): 0.25 A @ 0.25 to 12 Vdc
Insulation Depth: 1-1/2" to 3" (38 mm to 76 mm)
Mounting: L4008E1156—Horizontal or vertical;
Bulb Size: 3/8" X 2-7/8" (10 mm x 73 mm) copper
L6006A1145—horizontal
SOURCE 1 PART NO.
APPLICATION
S1-L6006A1145
CIRCULATOR CONTROL AND HIGH LIMIT
OR LOW LIMIT
TEMPERATURE
RATINGS
(OPERATING RANGE)
DIFFERENTIAL
SWITCH
ACTION
MLP $
5ºF TO 30ºF ADJ. (3ºC TO 17ºC ADJ.)
SPDT
243.46
HONEYWELL ZONE VALVES
Sweat less end switch zone valve, necessary for temperature control of a single zone in a hydronic heating system.
Features:
• Use with thermostat with special heat anticipator designed for best performance when used with the V8043 Zone Valve.
• Require 24 V power source.
Specifications:
Valve Dimensions (mm): Valve: 101 mm H x 90 mm W x
Body Pattern: 2-Way
60 mm D
Pipe Connections: Sweat
Approv als, Underw riters Laboratories Inc
Valve Electrical Rating (Voltage,
UL Listed: Models V8043A,B,E,J & V8044A,B,E; UL
Frequency): 24 VAC, 50/60 Hz
Component Recognized: V8043F
Valve Electrical Connections (in.): 18" leads
Valve action: Spring return to close
Approv als, Canadian Standards Association
CSA Certified: File no. LR95329-1
Valve Dimensions (in.): Valve: 4”H, 3-1/2”W, 2-3/8”D
MAXIMUM CLOSE-OFF
PRESSURE
CAPACITY
SOURCE 1 PART NO.
PIPE SIZE
PSI
KPA
CV
KV
MLP $
S1-V8043A1029
S1-V8043E1020
3/4"
1"
20
20
138
138
3.5
3.5
3
3
164.14
207.14
107
HONEYWELL AQUASTAT® RELAYS
Immersion-type controllers that combine high limit protection with switching relay control of burner and circulator motors.
Features:
• High limit opens burner circuit only.
• Include transformer and accessory terminals for adding a remote low limit controller.
• Case available for horizontal or vertical mounting.
Requires a 24 VAC thermostat with heat anticipator set at 0.2A.
• TRADELINE models include well adapter, tube of heat conductive compound and range stops.
Specifications:
Application: High Limit
Voltage: 120 VAC
Operating Range, High Limit (F): 120°F to 240°F
Frequency: 60 Hz
Operating Range, High Limit (C): 54°C to 116°C
Capillary Length (in.): 4-1/2"
Differential Temperature (F): 8°F fixed
Capillary Length (mm): 114 mm
Setpoint Temperature Range (F): 240°F
Insulation Depth (in.): 1-1/2" to 3" less well.
Setpoint Temperature Range (C): 116°C
Insulation Depth (mm): 38 mm to 76 mm less well
Sw itching Action SPST: High Limit & Circulator
Humidity Ratings (%RH): 0 to 95% RH, noncondensing
Maximum Ambient Temperature (F): 150°F with 1.2 A
Maximum Operating Pressure (psi): Immersion Well: 255 psi 24 V load; 77 F with 1.4 A 24 V load
Maximum Operating Pressure (kPa): Immersion Well: 1757
Maximum Ambient Temperature (C): 66°C with 1.2 A
kPa
24 V load; 25 C with 1.4 A 24 V load
Electrical Ratings (burner AFL): Line Voltage: 7.4 A @ 120
Electrical Connections: Quick-Connect / Screw
VAC; 3.7 A @ 240 VAC
Approv als, Underw riters Laboratories Inc
Electrical Ratings (burner ALR): Line Voltage: 44.4 A @ 120 UL Listed: File No. MP466, Vol. 13, Sec. 2, Guide
VAC; 22.7 A @ 240 VAC
No.MBPR2.
Electrical Ratings (burner millivolt): 0.25 A @ 1/4 to 12 Vdc Approv als, Canadian Standards
Electrical Ratings (circulator AFL): 7.4 A @ 120 VAC; 3.7 A Association Certified: File No. LR1620, Guide No.
@ 240 VAC
400-E-O
Electrical Ratings (circulator ALR): 44.4 A @ 120 VAC; 22.2
A @ 240 VAC
DIMENSIONS
SOURCE 1
PART NO.
S1-L8148A1017
APPLICATION
S1-L8148J1009
AQUASTAT
RELAY
HIGH LIMIT
MOUNTING TYPE
HORIZ. MOUNT
4-5/16”H X 6-1/8”W X 3-1/8”D (110 MM H X 156 MM W X 79
MM D)
VERTICAL/HORIZONTA 4-5/16”H X 6-1/8”W X 3-1/8”D (110 MM H X 156 MM W X 79
L
MM D)
HORIZONTAL
VERT. MOUNT
MLP $
-
391.75
6-1/8”H X 4-5/16”W X 3-1/8”D (156 MM H X 110 MM W X 79 445.46
MM D)
WR GAS WATER HEATER VALVES
For replacement of standard gas water heater controls with built-in E.C.O. (Energy Cut Off).
Specification:
Features:
Inlet Size: — 1/2” NPT.
• Automatic shut-off of main and pilot gas in.
Outlet Size: — 1/2” Inverted Flare
• the event of pilot failure.
Outlet Adapter Fittings (furnished with controls
• Pilot gas cock with safe lighting feature.
noted below ): 1/2” inverted flare x 3/8” NPT reducer adapter.
• Pilot gas filter.
1/2” x 1/2” inverted flare outlet extension adapter (F26-0021)
• Temperature adjustment.
Mounting: 3/4” NPT, 1-1/4”, shank length, 4-1/2” bulb insertion
• Manifold pressure tap.
length
• Built-in E.C.O. (Energy Cut Off) non-cycling high limit.
Pilot Connection: 1/4” compression fitting for use with Natural
• A.G.A. Certified.
Gas
PRESSURE REGULATION
SOURCE 1 PART NO.
Description
MAIN BURNER
PILOT
TEMPERATURE RANGE
S1-37C73U-168
Gas Water Heater Valves 1-1/4” Shank Length
3.5” W.C.
FIXED
70 TO 160° F (21 TO 71° C)
* Outl et adapter fi ttings included.
108
SHANK
LENGTH
1-1/4”
MLP $
235.14
HVAC Components
CONTACTORS
Source 1 Definite Purpose Contactors
SOURCE 1 PART NO.
POLES
AMPS
VOLTAGE
MLP $
S1-DP130024
S1-DP230024
S1-DP230120
S1-DP230240
S1-DP240024
S1-DP240120
S1-DP240240
S1-DP330024
S1-DP330120
S1-DP330240
S1-DP340024
S1-DP340120
S1-DP340240
1
2
2
2
2
2
2
3
3
3
3
3
3
30
30
30
30
40
40
40
30
30
30
40
40
40
24
24
120
240
24
120
240
24
120
240
24
120
240
11.36
14.71
14.61
14.61
16.68
16.79
16.79
27.39
27.71
27.71
28.46
28.43
28.43
Type 3100 and 3186 Contactors
Features:
• Application - power and pilot duty
• Insulation class B
• All terminals are combination screw & push-on
• 50/60 Hz
• Meets device specifications up to 600 VAC per bulletin 508
• Panel mounted
• Dimensions are maximum
• Box lug power terminal (L)
CONTACT
RATINGS FLA
SOURCE 1 PART NO.
VENDOR PART
NO.
S1-02425839700
S1-02425841700
S1-02425842701
S1-02425843700
S1-02425845700
S1-02425852700
3100Y20T615
3100Y20T1815CL
3100Y30Q915HT
3100Y30T915
3100Y30T1015CL
3186Y30T9015CL
POLE
CONFIG.
(NORM.
OPEN)
2P
2P
3P *
3P
3P
3P
CONTACT
RATINGS LRA
COIL DATA
CONTACT
RATINGS R
RTG.
240 V480 V600 V240 V480 V600 V240 V 480/600 VTS. HZ
V
30
40
30
30
40
90
30
40
30
30
40
90
30
40
30
30
40
90
150
240
180
180
240
540
125
200
150
150
200
450
100
160
120
120
160
360
40
50
40
40
50
120
40
50
40
40
50
120
120
120
24
120
120
120
50/60
50/60
50/60
50/60
50/60
50/60
MAX MIN DWG. NO.
INS.
MAX
MAX
CLASS INRUSH SEALED
VA 50/60 VA 50/60
B
B
B
B
B
B
40/37
40/37
55/52
55/52
55/52
325/270
* Indi cates Auxili ary Contacts (1) Normally Open (NO), (1) Normal ly Closed (NC), Rated 10A @ 115 - 600 Vol ts.
109
WIRE SIZE
10/8
10/8
11/9
11/9
11/9
38/25
8
4
8
8
4
1/0
16
14
16
16
14
14
2
3
4
4
4
6
MLP $
20.39
25.61
78.46
39.57
45.25
291.11
HVAC Components
CONTACTORS
Honeywell Deluxe PowerPro DP-Series Definite Purpose Contactors
Definite purpose one (25A, 30A, 40A) and two (20A, 30A, 40A) pole contactors provide switching for across-the-line starting of inductive motors.
Features:
• Meets ARI-780 Standard at started ratings (500,000 cycle mechanical life, 200,000 cycle electrical life and 10,000 cycle recycle life); the most demanding
ARI requirement.
• Silver cadmium oxide contacts provide long life under demanding duty cycles.
• Low profile design allows for more wiring room.
• Multiple mounting holes and slots for convenient, interchangeable mounting with most competitive devices.
Specifications:
Approv als: UL Component Recognized: File number E597 Guide number NLDX2 CSA Certified: File number LR95329-A224
Electrical Connections (main): sems screws
Contact Connections (coil): 1/4” quick-connects
Electrical Ratings, Contacts (AFL @ 240 VAC & 277 VAC): 30 A @ 240/277 VAC
Poles: 2
Temperature Ratings: –4° to +149° F (–20° to +65° C)
SOURCE 1 PART NO.
S1-DP1030A5013
S1-DP2030A5012
S1-DP2030B5011
S1-DP2030C5010
S1-DP2030D5001
S1-DP2040A5003
S1-DP3030A5003
S1-DP3040A5002
COIL RATINGS
VOLTAGE (V)
24 VAC
24 V
120 V
208/240 V
24 VAC
24 VAC
24 VAC
24 VAC
ELECTRICAL RATINGS, CONTACTS (RESISTIVE @ 240 VAC & 277 VAC)
H
W
D
MLP $
48 A @ 240/277 VAC
48 A @ 240/277 VAC
48 A @ 240/277 VAC, 480 VAC, 600 VAC
48 A @ 240/277 VAC, 480 VAC, 600 VAC
48 A @ 240/277, 480, 600 VAC
50 A @240/277 VAC
40 A @240/277, 480, 600 VAC
50 A @240/277, 480, 600 VAC
2-3/16
3-1/4
2-3/16
2-3/16
2-3/16
2-3/16
3-1/8
3-1/8
2-1/2
2-5/8
3-5/16
2-1/2
2-1/2
3-3/16
3-5/8
3-5/8
3-5/16
3-3/4
2-5/32
3-5/16
3-5/16
2
2-3/8
2-3/8
31.86
52.79
46.07
46.36
42.29
73.71
68.07
80.86
Honeywell Economy DP-Series Definite Purpose Contactors
•
•
•
•
These electromechanically-operated definite purpose contactors provide switching for starting induction motors.
Silver cadmium oxide terminals provide long life under demanding duty cycles
Low profile design allows for more wiring room
Multiple mounting holes and slots for convenient, interchangeable mounting with most competetive devices
SOURCE 1 PART NO.
S1-DP1030A1000
S1-DP2030A1003
S1-DP2040A1002
COIL RATINGS ELECTRICAL RATINGS, CONTACTS (RESISTIVE @ 240 VAC & 277 VAC)
VOLTAGE (V)
24 VAC
48 A @ 240, 277, 480, 600 VAC
24 VAC
48 A @ 240, 277, 480, 600 VAC
24 VAC
40 A @ 240/277 VAC, 480 VAC, 600 VAC
H
W
D
MLP $
3-1/4
2-10/27
3-5/8
3-3/10
3-13/16
2
18.68
22.86
42.25
Square D, Replacement Auxiliary Contact
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-D10
S1-D11
1- N.O., 50-90 AMP
1- N.O., 1 N.C., 50-90 AMP
28.25
52.86
110
HVAC Components
CONDENSATION CONTROLS & COMPRESSOR PROTECTION MODULES
ICM Condensation Controls
ICM’s condensate control systems protect cooling and refrigeration equipment by detecting and preventing overflows in the evaporator condensation pan due
to slow and/or blocked drains or pump failure.
Specifications:
Input: 18–30 VAC, 50–60 Hz
SOURCE 1 PART
NO.
S1-ACH55
S1-ICM340
S1-ICM342
S1-ICM345
ADDITIONAL FEATURES
OUTPUT
DELAY
DIMS (IN)
Optional Overflo W Alarm Led Kit for Use with
S1-ICM340 or S1-ICM342 Cable Length: 6 Ft.
2 SENSORS MAX. OPERATING/STORAGE RH 24 VAC TO THERMOSTAT/ COOLING CONTROL
1–3 MIN.
—
95% NON-CONDENSING STORAGE
24 VAC TO OPTIONAL OVERFLOW LED 2 AMPS
TEMPERATURE: -40° TO 85°C REPLACES
WATER GUARD: 401475
ALARM OUTPUT DURING LOCKOUT
TYPE: RELAY N.O.: 10A @ 120 VAC N.C.: 10 A @ ON MAKE CUSTOM AVAILABLE, FIXED OR 2.75 X 3.25
CONFORMAL COATING FOR MOISTURE
120 VAC
ADJUSTABLE
PROTECTION
AUDIBLE/VISIBLE CONDENSATION ALARM ASC
4.5 X 2.75 X
TYPE: RELAY N.O.: 1A @ 30 VAC
ANTI-SHORT CYCLE: 5 MIN. FIXED
COMPRESSOR PROTECTION WORKS WITH
0.875
ANY EXISTING THERMOSTAT OR
CONDENSATION CONTROL
111
MLP $
27.32
56.39
31.57
46.46
HVAC Components
CONDENSATION CONTROLS & COMPRESSOR PROTECTION MODULES
ICM Lockout Protection
The S1-ICM221 is a low-cost compressor protection module that monitors safety switch inputs and provides anti-short cycle protection. S1-ICM220 and
S1-ICM222 are low-cost lockout protection modules that monitor various switch inputs to help protect the compressor.
Specifications:
Voltage: 18–30 VAC
Frequency: 50–60 Hz
SOURCE 1 PART NO.
DESCRIPTION
DIMENSIONS (INCHES)
MLP $
S1-ICM220
COMPRESSOR CONTROLLER, LOCKOUT RELAY IDEAL FOR USE WITH
SAFETY/INTERLOCK SWITCHES 2 WATTS MAX. POWER CONSUMPTION
@ LOCKOUT RELAY: 1 FORM C, CONTACTS: 2A @ 30 VAC RESISTIVE
COMPRESSOR PROTECTION MODULE WITH 1-SECOND
INTERROGATION SAFETY SWITCH MONITORING 3 OR 6 SEC. DELAY ON
MAKE, SELECTABLE 10 SEC. OR 5 MIN. ANTI-SHORT CYCLE TIME
LOCKOUT PROTECTION MODULE WITH PRESSURE/FLOW SWITCH
MONITORING FAULT TYPE: RELAY (SPDT) N.O., FAULT RATING: 1A @ 30
VAC 5 MIN. FIXED ANTI-SHORT CYCLE TIME ±20% (5 SEC. TEST MODE)
2X2
36.39
3.25 X 3 X 1
56.89
3.5 X 3.25 X 1
56.89
S1-ICM221
S1-ICM222
COMPRESSOR PROTECTION
CPS Products 5-2-1 Compressor Saver
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CP-CSRU-1
S1-CP-CSRU-2
S1-CP-CSRU-3
HARD START KIT,5-2-1 COMPRESSOR SAVER,1-3 TON
HARD START KIT,5-2-1 COMPRESSOR SAVER,3.5-5 TON
HARD START KIT,5-2-1 COMPRESSOR SAVER,4-5 TON
N/A
N/A
N/A
112
HVAC Components
COMPRESSOR PROTECTION
CPS Products 5-2-1 Compressor Saver Surge Protector
The 5-2-1 Compressor Saver introduces the SPD150 surge protection device that incorporates the latest in protection technology and
ease of installation. These devices are designed to protect your equipment by suppressing the harmful energy produced by lightning
strike s and other power line transients commonly found in HVAC installations. The voltage surges or spikes can be very damaging to
HVAC equipment, shortening the life of the compressor and reducing its efficiency.
Features:
•
•
•
•
•
•
•
•
Device built with Patented MOV protection parts
Green LED indicates surge protection is present
Red LED indicates that power is present
INDEPENDENT of the surge protection status
TUV / 1449 3rd Edition approval
Weatherproof housing
Easy installation
Low cost, high performance
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CP-SPD150
SURGE PROTECTOR,5-2-1 COMPRESSOR SAVER
127.00
HARD START DEVICES
ICM Current Sensing Hardstarts
By monitoring the compressor current upon startup, ICM RapidStart® is able to engage the hard start capacitor for precisely the
correct amount of time, ensuring maximum starting torque without the risk of supplying too much current into the start winding. A
timed safety circuit is provided in the event the motor fails to start within 2 seconds.
Features:
• Operates from 95–288 VAC
• Patented current sensing circuitry
• Easy, 2-wire installation
• OEM-approved, Solid-state circuitry
• Boosts starting torque, Disengages upon start
• Recycles instantly (less than 1 second)
• Fuse protection
• Not affected by voltage or current fluctuations
• Not affected by ambient temperatures
Specifications:
Maximum Input Voltage: 502 VAC
Operating Temperature Range: -40°C to +65°C
SOURCE 1 PART NO.
APPLICATION
CAPACITOR
REPLACES
MLP $
S1-ICM803
S1-ICM805
S1-ICM810
1/2–3 HP
2–5 HP
3-1/2 - 10 HP
88–106 MFD. 330 V
145–175 MFD. 330 V
243-292 MFD, 330V
KICKSTART: T05, T0-5 SUPCO: SPP-8 SPP-8E
KICKSTART: KS1
75.04
82.75
98.93
Wiring Diagram Legend:
C = Common Terminal, R = Run Terminal, S = Start Terminal,
RC = Run Capacitor, RS = Rapid Start, SC = Start Capacitor
Maximum Input Voltage = 502 VAC RMS (maximum run capacitor volts)
Input Voltage = Run winding volts + Start winding volts
Note: Run capacitor voltage is higher than line voltage.
113
HVAC Components
HARD START DEVICES
ICM 3-in-1 Hardstarts
Features:
• For single-phase commercial and domestic capillary refrigeration systems and freezers
• Pre-wired for fast installation
MAXIMUM
SOURCE 1 PART NO.
APPLICATION RANGE
OPERATING VOLTAGE
S1-ICM857
S1-ICM858
S1-ICM859
1/12 - 1/5 HP
1/4 - 1/3 HP
1/3 - 1/2 HP
120V
120V
120V
VOLTAGE CURRENT
180V
180V
180V
12A
12A
12A
RETRY TIME
MLP $
WITHIN 90 SECONDS
WITHIN 90 SECONDS
WITHIN 90 SECONDS
29.07
29.07
56.96
ICM PTCR Hardstart Capacitors
Features:
• Increases starting torque
• Positive Temperature Coefficient (PTC) Technology
• Easy to install
• Low cost motor starting device
SOURCE 1 PART NO.
VOLTAGE
RANGE
CAPACITOR
MLP $
S1-ICM855
S1-ICM856
115-288 VAC
115-288 VAC
0.5 - 1.5 HP
2.0 - 5.0 HP
43 to 52 MFD, 330V
88 to 106 MFD, 330V
15.93
25.39
ICM Voltage Sensing Hardstarts
Features:
• Differential voltage sensing
• The best technology competitively priced
• Reduces inventory
• Ensures precise starts
• Increases starting torque
• Not effected by ambient temperature
• Recycles instantly (less than 1 second)
• Multi-voltage operation either 115 or 230 VAC motors
SOURCE 1 PART NO.
VOLTAGE
S1-ICM850
S1-ICM860
90 TO 277 VAC
90 TO 277 VAC
MAXIMUM
INPUT
VOLTAGE
390 VAC
390 VAC
RANGE
UP TO 1 1/2 HP
2 TO 5 HP
OPERATING
TEMPERATURE
RANGE
-40°C TO +65°C
-40°C TO +65°C
CAPACITOR
REPLACES
MLP $
43 TO 52 MFD. 330V
88 TO 106 MFD. 330V
SUPCO SPP-5, MARS 32701, A-1 WXS-5
SUPCO SPP-6, MARS 32702, A-1 WXS-6
40.71
47.29
FREEZE PROTECTION & DEFROST CONTROLS
ICM Freeze Protection Modules
Low-cost, fixed, single setpoint temperature controls that provide freeze protection.
Features:
Specifications:
Input Voltage: 18–30 VAC
• Epoxy encapsulated for moisture protection
Input Frequency: 50–60 Hz
• Temperature sensor included
Output: Solid state (triac), 1.5A @ 30 VAC
Dimensions: 2” x 2” x 1-1/4”
SOURCE 1 PART NO.
S1-ICM308
S1-ICM309
S1-ICM310
TEMPERATURE CUT-OUT
(OFF)
43°F
28°F
44°F
114
TEMPERATURE CUT-IN
(ON)
45°F
55°F
48°F
MLP $
23.18
23.18
22.82
HVAC Components
FREEZE PROTECTION & DEFROST CONTROLS
ICM Timers & Controls
Specifications:
Input Frequency: 50/60 Hz
Power Consumption: 1 watt maximum
Output Type: Relay
Defrost Time Delay: Fixed 10 minutes ±5%
Power on Reset Time: 500 milliseconds
Test Time: Short across test terminals reduces test time 256x
SOURCE 1
PART NO.
S1-ICM300
S1-ICM301
S1-ICM302
APPLICATION
S1-ICM303
HEAT PUMP DEFROST TIMER
DEFROST TIMER WITH HIGH POWER
FAN RELAY OUTPUT
HEAT PUMP DEFROST CONTROL
S1-ICM304
S1-ICM307
S1-ICM315
SOLID STATE DEFROST CONTROL
S1-ICM316
SOLID STATE DEFROST TIMER
S1-ICM317
S1-ICM318
S1-ICM319
S1-ICM320
SOLID STATE DEFROST CONTROL
S1-ICM321
S1-ICM322
S1-ICM323
S1-ICM330
HEAT PUMP DEFROST CONTROL
HEAD PRESSURE CONTROL
INPUT
VOLTAGE
18–30 VAC
18–30 VAC
18–30 VAC
OUTPUTS
RELAY, SPST, N.O., 1A
RELAY, SPST, N.O, 1A
RATING: 1 AMP @ 30VAC
1HP FAN @ 240 VAC; 24 VAC 2A STRIP HEAT/REVERSING
VALVE
W: RELAY, SPST, N.O., 10A @ 24 VAC RVS,CC: TRIAC, SPST,
18–30 VAC
N.O., 10A @ 240 VAC FAN: RELAY, SPST, N.O., 10A @ 240 VAC
18–30 VAC COMPRESSOR CONTACTS: TRIAC, 1A DEFROST RELAY: TRIAC,
1A
24, 120 OR
N.O.: 20A N.C.: 10A @ 240 VAC
240 VAC
18–30 VAC O, X2: DPST, N.O., 1A @ 30 VAC ODF: SPDT, N.C., 1A @ 230 VAC
EDR: DPDT, N.C., 1A @ 30 VAC
18–30 VAC
RELAY, SPST, N.O, 1A
18–30 VAC 1/2 HP 240 VAC OUTDOOR FAN RELAY 24 VAC 1A STRIP HEAT
REVERSING VALVE O, X2: DPST, N.O., 1A @ 30 VAC DF1, DF2:
SPST, N.O., 1/2 HP @ 240 VAC
18–30 VAC 1/2 HP 240 VAC OUTDOOR FAN RELAY 24 VAC 1A STRIP HEAT
REVERSING VALVE O, W2: DPST, N.O., 1A @ 30 VAC RESISTIVE
T1, T2: SPST, N.O., 10A @ 24 VAC DF1, DF2: SPST, N.O., 1/2 HP
@ 240 VAC
18–30 VAC O, W2: DPST, N.O., 2A @ 24 VAC DF1, DF2: SPST, N.O., 10A @
240 VAC
18–30 VAC O, W2: DPST, N.O., 1A @30 VAC RESISTIVE T1, T2: SPST, N.O.,
1A @ 30 VAC OF1, OF2: SPST, N.O., 1/2HP @ 240 VAC
O, W2: DPST, N.O., 1A @ 30 VAC T1, T2: SPST, N.O., 1A @ 30
18–30 VAC
VAC OF1, OF2: SPST, N.O., 1/2 HP @ 240 VAC
18–30 VAC
24 VAC, 1A STRIP HEAT REVERSING VALVES
18–30 VAC
MAX: 4 AMPS, MIN: 100mA
18-30 VAC
115
MLP $
INTERVAL TIME BETWEEN
DEFROSTS (PIN-SELECTABLE)
30/60/90 MIN
30/60/90 MIN
30/60/90 MIN
47.64
48.00
120.86
30/60/90 MIN
133.50
30/60/90 MIN
110.96
30/60/90 MIN
57.00
30/60/90 MIN
185.39
50/70/90 MIN
150.75
50/70/90 MIN
30/60/90 MIN
66.64
77.68
30/60/90 MIN
90.32
30/50/90 MIN
129.50
30/50/90 MIN
114.54
30/50/90 MIN
102.57
30/60/90 MIN
30/60/90 MIN
125.89
333.61
HVAC Components
MOTOR PROTECTION
ICM Single Phase Surge Protector
Features:
• Service Voltage: 120/240 Volt Single Phase
• Maximum Surge Current: 24000 Amps
• Maximum Energy Dissipation: 200 Joules
• Installation Point: Electrical Panel, Electrical Disconnect
• AC Protection Modes: L-L, L-G
Maximum
SOURCE 1 PART NO.
DESCRIPTION
S1-ICM515
SINGLE PHASE SURGE
PROTECTOR
Service Voltage Surge Current
120/240 Volt
Single Phase
24000 Amps
Energy
Dissipation
Installation
Point
200 Joules
Electrical Panel,
Electrical
Disconnect
AC
Protection
Modes
L-L, L-G
SIZE
WEIGHT
MLP $
1.75” X 1.62” X 0.75”
0.20 lbs.
37.54
ICM516 Single-Phase Surge Protector
Single-phase surge protector to protect against lightning power surges and equipment voltage surges; 100,000 amps / 1,400 joules
protection; 120-240 VAC
Specifications:
Service Voltage: 120/240 volt, single phase
Maximum Surge Current: 100,000 amps
Maximum Energy Dissipation: 1,400 joules
Installation Point:
- Electrical panel
- Electrical disconnect
AC Protection Modes: Line-line, line-ground
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ICM516
1-PHASE SURGE PROTECTOR
93.25
ICM 3-Phase Motor Protection
Protects Against:
• Under voltage
• Over temperature
• Power interruptions
• Rapid short cycling
• Shorted temperature sensor
• Open temperature sensor
• Control duty, SPST relay layout
• Anti-short cycle time delay, 4 min. (nominal)
• 1-second manual bypass
Specifications:
Voltage: 120 or 208/240 VAC
Output: Relay: SPDT N.O. 6A resistive
Dimensions: 3.25” x 3” x 1.25”
SOURCE 1 PART NO.
REPLACES
MLP $
S1-ICM441
BRISTOL: 241680,
COPELAND: 071-0376-01, 071-0376-02, 071-0397-00, 071-0397-01.071-0424-00, 071-0424-01.071-9800-00, 071-9800-01
MARS: 37300, 37302, 37304, 37306, 37322
TEXAS INSTRUMENTS: 15AA 1600 B, 15AA 1600 C, 15AA 1603 B, 15AA 1603C, 31AA 1600 E, 3
181.46
116
HVAC Components
MOTOR PROTECTION
ICM Universal Motor Starting Relays
Features:
• Replacement for all standard potential relays
• Patented differential voltage sensing
• No user adjustments required
• Non-positional mounting configuration
• 30A and 50A switching capabilities
• Universal mounting bracket for easy installation
• 0.250” quick-connect termination
• Safety timer
• Approvals: UL, CSA, cUL pending
Specifications:
Input:
Voltage Rating: 110–270 VAC, Single Phase
Maximum Voltage Contact Rating: 502 VAC (absolute)
Motor Pow er Rating: Up to 10 HP
Operating Position: Non-positional
Safety Time Out: Approximately 1 second per 100 microfarads
Consumption: 5VA max.
Insulation: Class B (130°C); Conforms to IEC 1000 standards
(6kV impulse / 6kV contact)
Life Expectancy (minimum operations):
Mechanical: 1 x 106
Electrical: 1 x 106 at 16A 400VAC
5 x 105 at 35A 400VAC (break only)
5 x 105 at 50A 400VAC (break only)
Contact Rating:
30A (break only), 400VAC cos Ø = 0.7 to 0.8
50A (break only), 400VAC cos Ø = 0.7 to 0.8
SOURCE 1 PART NO.
ICM PART NO.
MLP $
S1-UMSR-50
UMSR-50
38.75
CC750 Comfort Control Center
ICM’s award-winning CC750 Comfort Control Center works with your existing air conditioning system or heat
pump to improve its effectiveness at air moisture removal, while creating greater system efficiencies that help
promote energy
Ratings:
• Nominal 24 VAC inputs (±25%): 18-30 VAC RMS absolute
• Operating temperature: -40°F to +167°F (-40°C to +75°C)
• Power consumption: 10 watts typical
Line Ratings – Nominal 115 VAC RMS:
• Inverter operation: 95-135 VAC RMS absolute
• Bypass operation: 85-145 VAC RMS absolute
• Maximum inverter amps: 10 amps RMS
• Maximum bypass amps: 20 amps (60 Hz)
Line Ratings – Nominal 208-230 VAC RMS:
• Inverter operation: 180-264 VAC RMS absolute
• Bypass operation: 170-264 VAC RMS absolute
• Maximum inverter amps: 8.5 amps RMS
• Maximum bypass amps: 10 amps (60 Hz)
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CC750-115
S1-CC750-230
S1-PTB47
S1-RSN20
CC750 COMFORT CONTROL CENTER, 115VAC
CC750 COMFORT CONTROL CENTER, 230VAC
COIL SENSOR FOR USE W/CC750
RETURN SENSOR FOR USE W/CC750
752.93
752.93
65.54
65.54
117
HVAC Components
RELAY
Emerson SureSwitch Relay
SureSwitch™ Relay is a universal electronic upgrade and a superior replacement for mechanical compressor contactors.
5 Reasons to Install SureSwitch relay:
1. Pest Protection: Totally sealed relay to keep out ants and debris; no pest control treatments needed.
2. 5x Life vs. Traditional Contactor: Microprocessor control nearly eliminates contact damage.
3. No Noise: Latching internal relay won’t hum or buzz.
4. Time Delays: Protects sy stem when re-starting between regular cycles or after power interruptions.
5. Low Voltage Brow nout Protection: Detects and protects system from low voltage events that can cause compressor
and fan motors to overheat and fail prematurely.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-49P11-843
SURESWITCH RELAY FOR UP TO 40A, 208/240V. 1 OR 1.5 POLE
APPLICATIONS
119.96
FAN RELAYS
Source 1 Enclosed Fan Relays - 90-290Q thru 90-295Q WR/RBM Type 84
Single Pole Single Throw Normally Open (SPST-NO)
SOURCE 1 PART NO.
COIL VOLTAGE (50/60 HZ)
MLP $
S1-S90-290Q
S1-S90-291Q
S1-S90-292Q
24
120
240
12.21
12.18
12.18
SOURCE 1 PART NO.
MLP $
S1-S90-293Q
S1-S90-294Q
S1-S90-295Q
24
120
240
12.61
12.57
12.57
*Can be used as an isolation relay for digital thermostats when required.
Single Pole Double Throw (SPDT)
CONTACT RATING
125/250 VAC
INDUCTIVE
8 AMPS CONTINUOUS
25 AMPS INRUSH
RESISTIVE
16 AMPS
CONTINUOUS
Wiring Diagrams
Cross Reference Guide
MARS NO.
90290
90291
90292
90293
90294
90295
SOURCE 1
PART NO.
S1-S90-290Q
S1-S90-291Q
S1-S90-292Q
S1-S90-293Q
S1-S90-294Q
S1-S90-295Q
ALTERNATE
SOURCE 1 NO.
S1-S90-360
S1-90-362
S1-90-364
S1-S90-370
S1-90-372
S1-90-374
Source 1 Heavy-Duty Enclosed Fan Relays - 90-360 Thru 90-484 WR/RBM Type 184
Single Pole Normally Open (S.P.N.O.)
COIL DATA
SOURCE 1 PART NO.
RES.
S1-90-362
S1-90-364
S1-S90-360
120
208/240
24
1,800
7,000
77
118
NOM CURRENT
MA
25
12.5
125
NOM. VA
SEALED
3
3
3
INRUSH VA
MLP $
4
4
4
17.29
10.57
12.18
HVAC Components
FAN RELAYS
Source 1 Heavy-Duty Enclosed Fan Relays - 90-360 Thru 90-484 WR/RBM Type 184
Single Pole Double Throw (S.P.D.T.)
COIL DATA
SOURCE 1 PART NO.
RES.
S1-90-372
S1-90-374
S1-S90-370
120
208/240
24
1,800
7,000
77
SOURCE 1 PART NO.
RES.
S1-90-382
S1-S90-380
S1-S90-384
120
24
208/240
1,800
77
7,000
NOM. CURRENT
MA
25
12.5
125
NOM. VA
SEALED
3
3
3
INRUSH VA
MLP $
4
4
4
11.04
14.32
12.57
INRUSH VA
MLP $
4
4
4
10.11
12.57
12.57
Isolated Contacts (S.P.N.O./S.P.N.C.)
COIL DATA
NOM. CURRENT
MA
25
125
12.5
NOM. VA
SEALED
3
3
3
Wiring Diagrams
Source 1 2 Pole Switching Relays - S1-90-340 Thru S1-90-342 WR/RBM Type 91
Two Pole Double Throw (2P.D.T.) Fits Receptacles
A two pole double throw semi-enclosed relay. Easy to install and wire. Relay available for power or pilot duty. Suited for vending
machines, appliances, fan controls, heating and air conditioning applications and general purpose switching.
Features:
• Temperature Range:–40°F to 130°F
• Mechanical Life (no load): 750,000 operations, 30 operations per minute
• Electrical Life (rated load):
—100,000 operations, 6 operations per minute
—Load test making inrush ratings (0.4 to 0.5 P.F.); breaking 100% continuous rating-(0.65 to 0.8 P.F.)
• Weight (approximate): 6 oz.
Coils
• Frequency: 50/60 Hz
• Class Insulation: B
• Termination: 1/4” quick connect
• Operate: 85% of nominal coil voltage; 110% maximum safe operate
• Duty Cycle: continuous
COIL DATA
SOURCE 1 PART NO.
S1-S90-340
S1-S90-341
S1-S90-342
COIL VOLTAGE (50/60
HZ)
24
110/120
208/240
CONTACT RATING (PER POLE)
POWER
A.C.
VOLTAGE
125
250
277
INDUCTIVE
13.8 A 1/2 H.P.
13.8 A FULL LOAD
82.8 A INRUSH
1/2 H.P.
6 A FULL LOAD
35 A INRUSH 15 A
@ 75% P.F.
(POWER
FACTOR)
TERMINALS 1-2-3
TERMINALS 4-5-6
DC RES.
MA
POWER
POWER
POWER
POWER
POWER
POWER
15
400
1415
334
66
38
NOM. INRUSH
VA
VA
8
22
8
22
8
22
MLP $
14.75
14.86
14.86
CONTACT TERMINAL ARRANGEMENT
MOUNTING HOLE SIDE
COIL TERMINALS SIDE
PILOT
RESISTIVE
INDUCTIVE
RESISTIVE
15 A
1/10 H.P.
125 V.A.
3A
15 A
1/10 H.P.
125 V.A.
3A
15 A
—
3A
N.C. = Normally Closed
119
N.O. = Normally Open
HVAC Components
FAN COIL RELAY CONTROLS
ICM6200 Fan Coil Relay Control
Fan coil relay control center for operating line voltage, 3-speed fan motor with low voltage controls; For 2- or 4-pipe, heat pump, autochangeover applications.
Specifications:
Input:
- Transformer Primary: 115 VAC, 50-60 Hz
- Fan Inputs HI, MED, LOW: Nominal 17mA @ 24 VAC
- Heat & Cool: 1.5A @ 24 VAC
Output:
- Transformer Secondary: 24 VAC; 20 VA
- Relay Outputs HI, MED, LOW: 1/8 HP @ 115 VAC; 10A @ 240 VAC resistive max.
- Heat & Cool Valves: 1.5A @ 24 VAC
SOURCE 1 PART NO.
DESCRIPTION
S1-ICM6200
STD.
PACK
10
MLP $
171.57
Fan coil and electric heat control center for operating line voltage, 3-speed fan motor with low voltage controls; For 2- or 4-pipe,
aquastat auto-changeover, heat pump applications.
Specifications:
Input:
- Transformer Primary (L1 & L2): 115 VAC, 50-60 Hz
- HI, MED, LOW (8, 7, 6): Nominal 17mA @ 24 VAC
- Inputs 1-5, Aqua Heat & Cool: 1.5A @ 24 VAC
Output:
- Transformer Secondary: 24 VAC; 20 VA
- Relay Outputs HI, MED, LOW: 1/8 HP @ 115 VAC; 10A @ 240 VAC resistive
- HTR Output: 30A @ 240 VAC resistive
- Heat & Cool Valves: 1.5A @ 24 VAC
SOURCE 1 PART NO.
DESCRIPTION
S1-ICM6201
STD.
PACK
10
MLP $
186.89
TIME DELAYS
ICM Fixed Delay Time Delays
Features:
• Works with anticipator type thermostats
• Higher 1.5 amp power rating
• Simple, 2 wire hookup
• Compact 2” x 2” package
Input:
• Control Voltage: 18–30 VAC
• Power Consumption: 2 watts max. during timing
Output:
• Ratings: max. 1.5 amps, min. 40 µa, inrush 15 amps
• Voltage Drop: 2.5 VAC max @ 1.5 amps on make timers; 4.5 VAC max @ 1.5 amp, 3 amps typical on break
timers
• Bypass resi stor: <1 K @ 24 VAC
Mechanical:
• Mounting: surface mount using (1) #8 or #10 screw
Env ironmental:
• Operating temperature: –40° to +75°C, –40° to +167°F
• Transient protection: meets IEEE 587 standards for categories A & B without false output or degradation.
(6kv 0.5 µs x 100 Khz ring wave, 6kv 1.2 x 50 µs impulse wave)
SOURCE 1 PART NO.
MFG. NUMBER
TIME DELAYS
S1-ICM100
S1-ICM100F
S1-ICM101
S1-ICM101F
ICM100
ICM100F
ICM101
ICM101F
3 MIN.
3 MIN.
5 MIN.
5 MIN.
* F suff ix denotes 6” w ire leads
120
DELAY
ON MAKE
ON MAKE
MLP $
16.57
16.46
16.57
16.46
HVAC Components
TIME DELAYS
ICM Adjustable Delay Time Delays
Features:
• Knob-adjustable time delays
• Higher 1.5 amp power rating
• Simple, 2 wire hookup
• Works with anticipator type thermostats
• Spin proof knob
• 6” wire leads
Input:
• Control Voltage: 18–240 VAC
• Power Consumption: 2 watts max. during timing
Output:
• Ratings: max. 1.5 amps, min. 40 µa, inrush 15 amps
• Voltage Drop: 2.5 v max @ 1.5 amps on make timers; 4.5
v max @ 1.5 amp, 3 amps typical on break timers
• Bypass resi stor: <1 K @ 24 VAC
Mechanical:
• Mounting: surface mount using (1) #8 or #10 screw
Env ironmental:
• Operating temperature: –40° to +75°C, –40° to +167°F
(6 Kv 0.5 µs x 100 Khz ring wave, 6 Kv 1.2 x 50 µs impulse wave)
SOURCE 1 PART NO.
MFG. NUMBER
TIME DELAYS
S1-ICM102
S1-ICM102F
S1-ICM103
S1-ICM104
S1-ICM105
ICM102
ICM102F
ICM103
ICM104
ICM105
0.03–10 MIN. (1.8–600 SEC.)
0.03–10 MIN. (1.8–600 SEC.)
1–1023 SEC.
10–1000 SEC.
1.8–600 SEC.
* F suff ix denotes 6” w ire leads
121
DELAY
ON MAKE
MLP $
12.25
13.14
34.32
67.14
28.14
HVAC Components
TIME DELAYS
ICM Bypass Timers Series 175
Low pressure or oil switch bypass during startup, ideal for low ambient startups, integral component for “w inter start” kits...
The Series 175 may be used as an integral component in “winter start kits”, ideal for bypassing switches and for low ambient startups.
• 18-240 VAC operation
• Extends on-time switch closures
• Knob-adjustable delays: .01-1,000 sec.
• Precise digital timing circuitry
• One model replaces several in field
• Epoxy-encapsulated circuitry
•
recognized: E53944
certified: LR 30320
• Used to bypass a control or device during startup. Typically used to bypass a low pressure switch during compressor heat pump
startup or to bypass an oil pressure switch upon startup. Ideal in low ambient conditions. Integral component for “winter start’ kits.
Helps to eliminate nuisance lockouts.
With power applied to the input, the load is energized immediately and remains energized for the length of the time delay. At the
end of the time delay, the condition of the load is determined by the state of the bypassed switch.
Specifications:
Input
Output
• Control voltage: 18-240 VAC
• Ratings: max. 1 amp, min. 40 µa, inrush 10 amps
• Voltage drop: 2.5 V max. @ 1 amp
• Power consumption: 3 watts max.
• Leakage current: 5 µa max. @ 240 VAC
Time Delay
• Type: knob adjustable
• Range: 10-1,000 sec.
• Tolerance: 20% of selected time
Mechanical Mounting: surface mount using (1) #8 or #10 screw
Env ironmental
• Operating temperature: -40° to +75°C, -40° to +167°F
(6Kv 0.5 µs x 100 KHz ring wave)(6Kv 1.2 x 50 µs impulse wave)
SOURCE 1 PART NO.
ICM PART NO/PRODUCT CODE
MLP $
S1-ICM175
ICM175B/GPS00C2X1000P
30.86
ICM Delay On Break Timers
Features:
ICM's Delay on Break (DOB) Timers are low cost, direct OEM replacements that offer reliable, lasting protection for your
HVACR equipment. Provide anti-short cycle protection for your air conditioning, refrigeration and heat pump equipment. Each
unit features rugged, compact packaging and high power relays. UL listed. Choose from our extensive product selection to
best meet the needs of your application.
S1-ICM200, S1-ICM200F, S1-ICM201, S1-ICM201F
•
•
•
•
•
•
Compressor lockout/anti-short cycle timer
Helps to protect compressors from damage
Caused by rapid short cycling
Simple, 2-wire hookup
Fixed timing
18-30 vac
SOURCE 1 PART NO.
S1-ICM200
S1-ICM200F
S1-ICM201
S1-ICM201F
TIME
DELAYS
3 MIN.
3 MIN.
5 MIN.
5 MIN.
REPLACES
MLP $
A-1: EAC-501-180-W DIVERSIFIED: AC-100-3 SUPCO: TD733
A-1: EAC-500 SUPCO: TD733W
A-1: EAC-500, EAC-501-300-W DIVERSIFIED: ACS-500-5 SUPCO: TD735
A-1: EAC-500, EAC-501-300-W DIVERSIFIED: AC-505-5 SUPCO: TD735W
16.57
17.43
16.57
17.43
122
HVAC Components
TIME DELAYS
ICM Delay On Break Timers
S1-ICM203, S1-ICM203F
•
•
•
•
•
•
Helps to protect compressors from damage
Caused by rapid short cycling
Simple, 2-wire hookup
Adjustable timing
Universal voltage
SOURCE 1
PART NO.
S1-ICM203
S1-ICM203F
TIME DELAYS
REPLACES
0.03–10 MIN. (1.8–600 SEC.)
KNOB-ADJUSTABLE
0.03–10 MIN. (1.8–600 SEC.)
KNOB-ADJUSTABLE
A-1: EAC-501-ADJ DIVERSIFIED: AC-503 MARS: 32092, 32392 ROBERTSHAW: 3310-072 SUPCO:
TD-73 WAGNER/DIVERSITECH: ADB-1
SUPCO: TD73W WAGNER/DIVERSITECH: ADB-2
MLP
$
13.14
13.14
S1-ICM204, S1-ICM205, S1-ICM206
•
•
•
•
•
Brownout protection
Ul 873 recognition as compressor controller
Helps prevent scroll compressor reversal
18-30 vac
TIME DELAYS
REPLACES
SOURCE 1 PART
NO.
S1-ICM204
3 MIN.
A-1: EAC-426-180 DIVERSIFIED: AC-100-3 MARS: 32381, 32565 ROBERTSHAW: 3310-183 SUPCO: TL243
S1-ICM205
5 MIN.
A-1: EAC-426-300 DIVERSIFIED: AC-100-5 MARS: 32382 ROBERTSHAW: 3310-305 SUPCO: TL245
S1-ICM206
3–10 MIN. ADJUSTABLE
A-1: EAC-426-ADJ
MLP $
18.61
18.61
20.18
S1-ICM207, S1-ICM208 S1-ICM209
•
•
•
•
•
Compressor lockout/anti-short cycle timer.
Helps prevent scroll compressor reversal.
Works with anticipator-type thermostats.
Fixed or adjustable timing.
Universal voltage operation.
TIME DELAYS
SOURCE 1 PART
NO.
S1-ICM207
3 MIN.
S1-ICM208
5 MIN.
S1-ICM209
0.03–10 MIN. ADJUSTABLE
REPLACES
MLP $
A-1: EAC-426-ADJ
21.46
21.46
23.64
S1-ICM211
•
•
•
•
•
•
Low cost, open board package
Conformally coated for added protection
Fixed timing
18-30 vac
SOURCE 1 PART NO.
TIME DELAYS
REPLACES
MLP $
S1-ICM211
5 MIN.
N/A
21.18
S1-ICM210, S1-ICM212
•
•
•
•
•
•
•
•
•
Compressor lockout anti-short cycle timer plus
Random start function
Dual function delay on make/break
Random start delay is ideal for stagger-starting
Multiple units
Fixed timing
18-30 vac
Plastic standoffs (S1-ICM212)
SOURCE 1 PART NO.
TIME DELAYS
REPLACES
MLP $
S1-ICM210
S1-ICM212
5 MIN.
5 MIN.
A-1: EAC 650
A-1: EAC 650
25.07
25.07
123
HVAC Components
TIME DELAYS
ICM Random Start Timers
Ideal for use in compressor staging and to stagger-start multiple rooftop units. Helps to reduce power surges.
Features:
• Delay on make/delay on break
• UL 873 recognition as compressor controller
• Compressor lockout/anti-short cycle timer
• Integral random start capability
• Knob-adjustable time delay
Specifications:
Current: 1A maximum; 40mA minimum
Inrush: 10A
SOURCE 1 PART
NO.
S1-ICM150
S1-ICM151
ADDITIONAL FEATURES
TIME DELAYS
SPST, N.O.
SAFETY SWITCH LOCKOUT; REMOTE
THERMOSTAT RESET
6–600 SEC. VOLTAGE DROP 1.5V @ 1A
–0.1 THRU 600 SEC.
REPLACES
MLP $
DIMENSIONS
(INCHES)
2x2
DIVERSIFIED: ASC-200
38.64
BARD: 8201-088 CARRIER: HN67KZ002 YORK: 67.07
2x3
031-01204-000
ICM Duty Cycle Timers
Features:
• Duty cycle timer ideal for defrost applications
• Suitable for process equipment or applications requiring intermittent delays
• Switch-settable time delays
• Epoxy-encapsulated for greater reliability
• On time starts at power up.
Specifications:
Voltage: 18–240 VAC 1A
Inrush: 10A
Dimensions: 2” x 3”
SOURCE 1 PART NO.
TIME DELAYS
MLP $
S1-ICM305
S1-ICM306
SWITCH-SETTABLE FROM 1–1023 MIN. IN 1-MIN. INTERVALS
SWITCH-SETTABLE FROM 1–1023 SEC. IN 1-SEC. INTERVALS
73.07
73.07
124
HVAC Components
TIME DELAYS
ICM Post-Purge Fan Delay Timers Series 251, 252, 253, 254 & 255
Adj ustable OFF delay timer, controls the circulating fan in heat pump, and AC forced air systems...
The Series 253 provides reliable OFF delay timing in a rugged package. The OFF delay is knob-adjustable from 12-390 sec.
• Knob-adjustable OFF delay: 12-390 sec.
• OFF delay purges ducts of residual air at the end of the heating/cooling cycle
• Helps increase overall system efficiency
• Epoxy-encapsulated circuitry
• Solid state reliability
• Low cost
recognized: E118867
certified: LR 30320
•
• Controls the circulating fan in heat pump, air conditioning & forced air systems. OFF delay timing function continues to run the fan
at the end of the heating/cooling cycle, thereby purging ducts of residual air and increasing system efficiency.
• Power must be applied before and during the time delay period. When the initiate contact closes, the load energizes and remains
energized as long as the initiate contact is closed. The time delay begins when the initiate contact opens. At the end of the time
delay period, the load is turned off. If the initiate contact recloses during the time delay period the load remains energized and the
time delay is reset to zero. Removal of input power during the delay turns off the load and resets the time delay to zero. A one
second interrogation delay is provided to avoid nuisance trips due to thermostat bounce or tampering.
Specifications:
Input
• Control voltage: 18-30 VAC
• Power consumption: 2 watts max.
Output
• Ratings: max. 1 amp, min. 40 µa, inrush 10 amps
• Voltage drop: 1.25 V max. @ 1 amp
Time Delay
• Type: knob-adjustable only
• Range: OFF delay: 12-390 sec.
Mechanical Mounting: surface mount using (1) #8 or #10 screw
Env ironmental
• Transient protection: meets IEEE 587 standards for categories A & B without false output or degradation (6Kv 0.5 µs x
100 KHz ring wave)(6Kv 1.2 x 50 µs impulse wave)
SOURCE 1 PART NO.
S1-ICM251
S1-ICM253
S1-ICM254
S1-ICM255
ICM PART NO./PRODUCT
CODE
ICM251
ICM253
ICM254
ICM255
REPLACES
MLP $
MARS: 32377, 32378, 32379
FIELD CONTROLS: 46144700 GEMLINE: 1C216 MARS: 32393
HONEYWELL: S876A1016 WATSCO: PSTD-000-005W, PSTD-000-060W
A-1: 5893 BARD: 8201-056 MARS: 32393 RHEEM: 42-22515-01, 42,22515-02, 42-22515-03 SNYDER
GENERAL/ICP: 1395336
41.82
42.11
37.00
36.00
FAN BLOWER CONTROLS
ICM Fan Safety Alarm Circuit Control
Fan safety alarm circuit for air handling unit safety-shutdown
Specifications:
•
Input: 24 VAC; 50-60 Hz (4A max.)
•
Output:
- Relay Outputs (6): 2A @ 24 VAC/DC per output
- Master Relay 24 VAC (2): 1.5A @ 24 VAC per output
- Master Relay Dry Contacts: 10A @ 250 VAC
•
Alarm Status:
- Green LED ON = Activated
- Red LED ON = Not activated
SOURCE 1 PART NO.
DESCRIPTION
S1-ICM6100
Fan Safety Alarm Circuit Control
125
STD.
PACK
10
MLP $
236.93
HVAC Components
FAN BLOWER CONTROLS & FAN CONTROL CENTERS
ICM Fan Blower Control
Specifications:
SOURCE 1
PART NO.
S1-ICM270
S1-ICM272
S1-ICM273
S1-ICM274
S1-ICM276
S1-ICM277
DESCRIPTION
CONTACT RATINGS OR OUTPUT
TIME DELAYS
MLP $
DUAL FUNCTION FAN
HEAT/COOL SPEED N.O.: 20A @ 240 VAC N.C.: 10A @ 240 VAC
BLOWER ON: 30 SEC. BLOWER OFF: 90, 120, 150, 180 SEC.
128.39
DELAY TIMER
COOLING CONTROL
N.O. 20A, N.C.: 10A
BLOWER OFF: 60 SEC.
96.43
MODULE WITH FAN
DELAY
CIRCULATING FAN
OUTPUT: 2A @ 240 VAC
BLOWER OFF: 60 SEC.
49.32
CONTROL FOR HEAT
PUMP, A/C AND
FORCED AIR SYSTEMS
MICROPROCESSOR-BA OUTPUT: Y OUT: 1.5A FAN: 2A ELECTRIC HEAT RELAY: 30A @ 240
BLOWER OFF: 60 SEC.
111.00
SED FAN BLOWER
VAC
CONTROL
MICROPROCESSOR-BA
HEAT ON: 60 SEC. HEAT OFF: 120, 150, 180 SEC. COOL OFF: 60 133.18
OUTPUT: FAN: 20A @ 240 VAC INDUCER FAN: 2A
SED CIRCULATION FAN
SEC.
CONTROL IN GAS/HEAT
AND A/C SYSTEMS
MICROPROCESSOR-BA
N.O.: 20A, N.C.: 10A
BLOWER ON: 7 SEC. BLOWER OFF: 65 SEC.
73.18
SED CIRCULATING FAN
CONTROL IN HEAT
PUMP, A/C AND
FORCED AIR SYSTEMS
Replaces:
SOURCE 1
PART NO.
RHEEM
CARRIER
TEXAS
INSTRUMENTS
EMI
ROBERTSHAW
GOODMAN
S1-ICM270
47-22827-01
47,22827-81/82
47-22828-01/02
—
—
—
—
—
S1-ICM272
—
S1-ICM273
S1-ICM274
—
—
47-23619-02
47-23619-03
—
S1-ICM276
S1-ICM277
HK61GA001
HK61GA003
—
—
2FD-1
—
—
—
—
—
240000-969
240-1764
—
—
HK51GA003
—
—
—
—
—
—
—
457-23619-03
RS100-833-02
—
126
—
B13707355
HVAC Components
FAN BLOWER CONTROLS & FAN CONTROL CENTERS
ICM Fan Control Center ICM271
Features:
• Solid state fan blower
• Specifically designed to replace popular gas furnace centers
• Pin selectable blower delays
• High power, relay output
• Dual function fan delay timer
• Controls the circulating fan in heat pump, A/C and forced air systems
• OFF delay purges ducts for residual air
• ON delay allows air to reach the proper comfort level prior to energizing the fan
INPUT
SOURCE 1 PART NO.
S1-ICM271
DESCRIPTION
VOLTAGE
FAN CONTROL CENTER
Replaces:
ROBERTSHAW
695-100
FREQUENCY
18–30 VAC
50/60 HZ
CONTACT
RATINGS
N.O.: 20A
N.C.: 10A
FIXED TIME DELAYS
MLP $
ON: 75 SEC.
OFF: 105 SEC.
128.96
CARRIER
302075-3, CES0110017, CES0110018, HH84AA010, HH84AA011, HH84AA012,
HH84AA013, HH84AA020, P771-7002
ICM Fan Control Center ICM275
Features:
• Microprocessor-based fan blower control
• Built in humidity relay
• Manually adjustable post-purge off delay from 60–240 seconds
• Electronic air cleaner output
Replaces: Robertshaw 695-101
INPUT
SOURCE 1 PART NO.
DESCRIPTION
VOLTAGE
FREQUENCY
OUTPUT CONTACT RATINGS
TIME DELAYS
MLP $
S1-ICM275
FAN CONTROL CENTER
18–30 VAC
50/60 HZ
20A @ 240 VAC ON HIGH
10A @ 240 VAC ON LOW
ON: 60 SEC. FIXED
OFF: 60–240 SEC. ADJUSTABLE
131.61
127
HVAC Components
HEAD PRESSURE CONTROLS
ICM Head Pressure Controls with Heat Pump Bypass
Features:
Specifications:
• Integral Heat Pump Bypass Circuitry
Allows you to electronically bypass the speed control during heat pump
• Power Consumption: 4VA @ 24 VAC
operation
Output
• Solid state 10 amp load carrying capability
• Type: Solid State
• Single unit controls up to 3 refrigerant circuits
• Form: Triac
• Multiple Voltage Ranges
• Output Current: (maximum: 10 amps) (minimum: 100 mA)
• Hard Start
Adjustable from .1-5 seconds; provides full torque to the motor during
• Voltage Drop: 3.0 volts maximum
startup to help ensure proper fan rotation and lubrication of bearings
• Leakage Current: 5 mA maximum
• Low Speed Cutoff
Protection
Field-adjustable; user may set the minimum RPM level
• Dielectric Breakdown: 2,500 volts maximum
at which the condenser fan should operate
• Insulation Resistance: 100 M
• High Temperature Bypass
Control Operating Temperature
Applies full voltage to the condenser fan under normal conditions
• Operating Temperature: -40°C to +75°C (-40°F to +176°F)
• Integral Transformer *(ICM326HN/327HN models) Simplifies installation, reduces • Storage Temperature: -40°C to +85°C (-40°F to +185°F)
cost; direct setup from the line voltage
Dimensions
• RoHs Compliant/Lead Free Design For global us
• ICM325HN: 43/4”L X 33/16”W X 11/8”H
Applications
• ICM326HN and ICM327HN: 43/4”L X 33/16”W X 13/4”H
• Ideal for “Low Ambient” Conditions Found in:
Ordering Information
-Supermarkets, frozen food storage
• Standard Model ICM325HN: 120-480 VAC
-Computer rooms, cooling tower fans
• Models with Integral Transformers: CM326HN: 120/208/240 VAC
-Temperature/humidity-sensitive environment
ICM327HN: 480 VAC
SOURCE 1 PART NO.
DESCRIPTION
INPUT/OUTPUT VOLTAGE
MLP $
S1-ICM325HN
S1-ICM325HNV-LF
S1-ICM326HM2
S1-ICM326HN
S1-ICM327HN
ICM HEAD PRESSURE CONTROLS WITH HEAT PUMP BYPASS
120/208/240/480 VAC
600 VAC
120 OR 208/240 VAC
120/208/240 VAC
480 VAC
243.36
285.96
355.96
288.89
292.54
128
HVAC Components
ICM Head Pressure Controls with Temperature & Pressure Inputs and Optional Heat Pump Bypass
Features:
• Single (ICM332) or Dual (ICM333)Temperature or Pressure
Input
• Integral Heat Pump Bypass Circuitry: Allows you to electronically bypass the speed control during heat pump operation
• Solid state 10 amp Load Carrying Capability
• Heat Start: Adjustable from .1-5 seconds; provides full torque
to the motor during startup to help ensure proper fan rotation
and lubrication of bearings
• 120-600VAC
• Low Speed Cutoff: Field-adjustable; user may set the
minimum RPM level at which the condenser fan should operate
• High Temperature Bypass
Applies full voltage to the condenser fan under normal
conditions
• RoHs Compliant/Load Free Design: For global use
Specifications:
Input/Output Voltage
• Line: 120, 208, 240, 277, 480 and 600 VAC
• Output: 18-30 VAC • Frequency: 50-60 Hz
• Heat Pump Override: 24 VAC, N.C./N.O.
Probes:
• Temperature: Thermistor, 10K ohm at 77°F
• Pressure: ICM380 (ordered separately)
• Operating Temperature: -40°C to +75°C (-40°F to +176°F)
• Storage Temperature: -40°C to +85°C (-40°F to +185°F)
Dimensions:
• ICM332 and ICM333: 4 3/4”L x 3 3/16”W x 1 3/4”H
• Mounting: Surface mount using (2) #8 screws
SOURCE 1 PART NO.
DESCRIPTION
PROBE CONNECTIONS
MLP $
S1-ICM333
ICM HEAD PRESSURE CONTROLS WITH
TEMPERATURE AND PRESSURE INPUTS AND
OPTIONAL HEAT PUMP BYPASS
2 TEMPERATURE PROBES, 2 PRESSURE PROBES
259.11
ENCLOSURE
ICM Controls Enclosure
Features:
• Rugged steel construction
• Easy to mount
• Helps to protect controls from harsh environmental conditions such as temperature, shock, humidity and vibration
• For use with ICM325HN, ICM326HN, ICM327HN, ICM332, and ICM333HN head pressure controls.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ACC-OE-03
ENCLOSURE,WEATHERPROOF,FOR ICM325-ICM327
65.39
ICM 3-Phase Head Pressure Controls
Accessories for ICM 3-Phase Head Pressure Controls
SOURCE 1 PART NO.
DESCRIPTION
FOR USE WITH
LENGTH (IN.)
PSI
MLP $
S1-ICM380
OPTIONAL PRESSURE
TRANSDUCER *
TEMPERATURE PROBE
S1-ICM336, S1-ICM337, S1-ICM330
72
0–500
167.86
S1-ICM336, S1-ICM337
79
N/A
50.86
S1-ICM381
* 1/4” SAE fem ale fl are wi th Schraeder deflator (6’ long)
Probe for Head Pressure Controls with Optional Heat Pump Bypass Feature
SOURCE 1 PART NO.
FOR USE WITH
LENGTH
TEMPERATURE
MLP $
S1-ICM379
S1-ICM325H, S1-ICM326H, S1-ICM327H
6’ 7”
70°–100°F, 21°–38°C
57.39
129
HVAC Components
LINE MONITORS
ICM 3-Phase Monitor ICM401
The ICM401 is a low cost 3-phase line monitor that protects against phase loss, phase reversal and phase unbalance. Ideally sui ted
to protect scroll & screw compressors from reverse rotation.
Features:
• Low cost, single side 3-phase protection
• Bright LED indicators for fault and load energized
• Easy to install, no adjustments
• Wide operating range: 190-600 VAC
• Less than 1-second phase loss re sponse
• Automatic reset from a fault condition
• Compact packaging: fits almost anywhere
• Rugged, epoxy-encapsulation for extreme conditions
• Works great with the ICM450 for load side monitoring of part winding start motors and multiple compressor sy stems
INPUT
SOURCE 1 PART NO.
DESCRIPTION
VOLTAGE
FREQUENCY
S1-ICM401
3-PHASE LINE MONITOR
190-600 VAC
50/60 Hz
CONTROL
VOLTAGE
18-30 VAC
OUTPUTS
MLP $
SPDT N.O. 10A
71.43
ICM 3-Phase Monitor ICM402
The ICM402 is a low cost 3-phase line monitor, with a 30 amp output that protects against phase loss, phase reversal and phase
unbalance. Ideally suited to protect scroll and screw compressors from reverse rotation. If all three phases are relatively equal and in
proper sequence, the normally open contacts (Y/Y-OUT) will close when 115/230 volts is applied between C and 115/230 VAC
terminals. If the phases are out of sequence, or if one is missing, the contacts will never close.
Features:
• Low cost, single side 3-phase protection
• 30 amp output
• Bright LED indicators for fault and load energized
• Easy to install; no adjustments
• Wide operating range: 190–600 VAC
• Less than 1 second phase loss re sponse
• Automatic reset from a fault condition
• Compact packaging: fits almost anywhere
• Rugged, epoxy-encapsulation for extreme conditions
• Works well with the ICM450 for load side monitoring of part winding start motors and multiple compressor sy stems
Dimensions: 3.0” x 3.25” x 1.25”
INPUT
SOURCE 1 PART NO.
DESCRIPTION
LINE VOLTAGE
FREQUENCY
CONTROL VOLTAGE
OUTPUTS
MLP $
S1-ICM402
3-PHASE LINE MONITOR
190–600 VAC
50/60 HZ
115 OR 230/240 VAC
SPST N.O. 30A
74.86
130
HVAC Components
LINE MONITORS
ICM 3-Phase Voltage Monitor-Programmable ICM450
LCD Operating Temperature
Operating temperature: -20° to +75°C, -4° to 167°F
Phase Unbalance Protection
Voltage unbalance: 2-20% adjustable
Ov er/under protection
• Under voltage: 2-25% adjustable
• Over voltage: 2-25% adjustable
Phase Loss Protection
Phase loss condition= <25% of nominal for any given phase.
System will shut down and a fault will be recorded should this
Features:
• Reliable, high temperature LCD display simplifies sy stem condition occur.
Delay on Break Timer
setup and diagnostics. Indicates condition of incoming
line voltage, fault conditions, system setpoints and other • Control voltage: 18-240 VAC
• Time delay: 0-10 min. adjustable
user adjustments. Temp.: -20° to +75°C (-4° to +167°F)
Fault Interrogation Delay
• Simultaneous voltage display...an ICM exclusive!
• Time delay: 0-15 sec. adjustable
View all 3 phases, no need to scroll through readouts.
• Fully adjustable variables...user may easily set and adjust • Provides a delay between fault detection & system shut-down eliminating nuisance trips/unnecessary Shutdowns.
variables when in SETUP mode:
Mechanical
• Line voltage: 190-600 VAC
• Mounting: surface mount using (2) #8 screws
• Voltage unbalance: 2-20%
• Termination: screw terminals
• Delay on break period: 0-10 min.
• Weight: 12 ounces (341 grams)
• Fault interrogation: 0-15 sec.
• Easy to install and configure...wiring diagram on unit, simple
• Over/under voltage: 2-25%
7-step push-button setup, guide included.
• Reset modes: AUTO or 0-10 Retries
• 25-Fault memory and storage...clearly displayed in LCD
• Control modes: ON or OFF
• Ultra bright LED indicators...shows current mode:
Specifications:
Setup LED
Input
Load energized LED
• Line voltage: universal- 190-630 VAC
Control voltage LED
Fault LED
Output
Dimensions: 6.5” x 4.25” x 1.4”
• Type: relay, SPDT
Exclusive ICM Features
• Voltage range: Up to 240 VAC (Max: 10 amps)
1. View all 3 voltages at once.
2. Front and back side fault identification.
3. Independent over/under voltage % adjustment.
• Operating temperature: -40° to +75°C, -40° to 167°F
4. ICM450 wiring diagram printed right on cover.
• Storage temperature: -40° to +85°C, -40° to 185°F
5. High-temperature LCD: –20° to +75°C, -4° to 167°F.
6. Line voltage programmable - (no step-up transformer needed).
Stop Motor Burnouts!
3-Phase line v oltage monitor w ith 25-fault memory, hightemperature LCD display, easy setup & clear diagnostic
display of system faults, 190-630 VAC operation...
The ICM450 was specifically designed to protect motors and
other 3-phase loads from premature failure and damage due
to common voltage faults such as voltage unbalance,
over/under voltage, phase loss, reversal, incorrect
sequencing and rapid short cycling.
SOURCE 1 PART NO.
S1-ICM450
ICM PART NO./PRODUCT
CODE
ICM450
REPLACES
MLP $
S1-52531424000
281.82
Spanish-Language Model
SOURCE 1 PART NO.
ICM PART NO/PRODUCT CODE
REPLACES
MLP $
S1-ICM450-S
ICM450S
A-1: EAC-800, EAC-8000, EAC-8002 COPELAND:
085-0160-00 DIVERSIFIED: AC-2020, AC-301, AC-302
MOTORSAVER: 455 SSAC: QLM, QLV TIMEMARK: 265
WAGNER/DIVERSITECH: DPT-3, WPC-800
372.43
131
HVAC Components
LINE MONITORS
ICM 3-Phase Loss & Reversal Protection
Features:
• Reliable 3-phase protection for single side
• Monitors for phase reversal, phase loss, unbalance percentage as a function of input voltage
• Bright LED indicators for On and Fault
• Highly reliable passive electronics
• Phase reversal detection on power up
Specifications:
High Voltage Cut-Out Setpoint: +12%
Low Voltage Cut-Out Setpoint: –12%
Power/Phase Loss Detection: Within 100 ms
User Selectable Unbalance Voltage: 2%–8%
Adj ustable Delay on Break: 1–5 min.
Relay Output: N.O./N.C. contacts: 10A resistive @ 250
VAC
SOURCE 1 PART NO.
MOUNT
DELAY ON MAKE
MLP $
S1-ICM408
S1-ICM409
8-PIN PLUG-IN
DIN RAIL
1–5 MIN.
HEAVY-DUTY SPDT
143.14
174.79
ICM 3-Phase Voltage Monitor ICM400
Stop Motor Burnouts!
High performance, low cost model, front and back side
protection, 7 bright fault LEDs, integral short-cycle
protection, easy setup, fully adj ustable features, 190-630
VAC...
The ICM400 was specifically designed to protect motors and
other 3-phase loads from premature failure and damage due
to common voltage faults such as voltage unbalance,
over/under voltage, phase loss, reversal, incorrect
sequencing and rapid short cycling.
3-Position Reset Switch, 50/60 Hz
• Choose from 3 easy-to-select reset modes:
• Full manual
• Full automatic
• Auto front/manual back
Features:
• Bright LED’s show modes and identify faults:
Load energized LED
Control voltage LED
Lockout LED
Front fault LED
Back fault LED
High voltage LED
Low voltage LED
• Knob-adjustable variables...user may easily
• select and adjust setpoints on unit:
• Voltage unbalance: 2–25%
• Delay on break period: 1–5 min.
• Fault interrogation: 1–15 sec.
Specifications:
Input
Contactor Load Side (Back)
Load side monitoring is optional.
Output
• Type: relay
• Voltage range: 240 VAC (max: 10 amps)
• Operating temperature: -40° to +75°C, -40° to 167°F
• Storage temperature: -40° to +85°C, -40° to 185°F
Phase Unbalance Protection Voltage unbalance: 2-25%
adjustable
Ov er/Under Voltage Protection
• Under/over voltage: fixed at 12%
• Hysteresi s: 6%
• Low cost, high performance...full line protection and fault
identification without costly LCD readout
• Integral delay on break timer...knob-adjustable from 1-5 min.,
helps prevent rapid system recycling
• Easy to install and configure... wiring diagram on unit,
installation and application guide included
Phase Loss Protection Phase loss condition
= <25% of nominal for any given phase. System will shut down
and a fault will be recorded should this condition occur.
Delay on Break Timer: Time delay: 1–5 min. adjustable
Fault Interrogation Delay
• Time delay: 1-15 sec. Adjustable
• Provides a delay between fault detection and system
shutdown, eliminating nuisance trips/ unnecessary shutdowns.
Mechanical
• Terminations: screw terminals
• Weight: 12 ounces (341 grams)
• Dimensions: 6.5” x 4.25” x 1.4”
INPUT
SOURCE 1 PART NO.
DESCRIPTION
S1-ICM400
3-PHASE VOLTAGE MONITOR
LINE VOLTAGE FREQUENCY
ICM PART
NO/PRODUCT CODE
ICM400
190–600 VAC
50/60 HZ
132
CONTROL
VOLTAGE
18–240
VAC/VDC
OUTPUTS
MLP $
SPDT FREQUENCY:
50/60 HZ
294.21
HVAC Components
LINE MONITORS
ICM Relay Sockets
Features:
• For use with ICM408, ICM410-427, and ICM500-505
• Relay socket
• 8-pin octal plug-in base
• Locating key ensures proper orientation
• Order ACS-11 for 11-pin base
• 10 amps up to 480 VAC
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ACS-11
S1-ACS-8
ICM RELAY SOCKETS
ICM RELAY SOCKETS
17.25
17.25
ICM Single Phase Line Monitors Series 491
High/low v oltage protection for single phase systems, 95-270 VAC operation, adj ustable anti-short cycle timer, ultra low
cost...
The Series 490 was specifically designed guard equipment against damage caused under/over voltage and rapid system recycling.
Low cost single phase equipment protection
Protects against:
-Over/under voltage conditions
-Rapid system recycling
LED Indication (continuous under normal conditions)
Heav y Duty SPDT 8 amp Relay Output (isolated contacts)
Interrogation Delay helps prevent nuisance tripping
Integral, adj ustable anti-short cycle protection
Mode of Operation
Upon application of power to the monitor, and provided all voltages are acceptable, the LED indicator light will glow, indicating that the
output contacts have transferred.
Should a voltage unbalance or high/low voltage condition exist for longer than the 5 sec. interrogation delay, the relay and LED shall
be deenergized. Re-energization is automatic upon correction of the fault condition and after the anti-short cycle time delay period is
complete. Should a fault condition exist upon application of power, the output relay will not energize.
Adjustment: Select the proper operating line voltage. Apply power. If the relay fails to energize, check wiring. Adjust lockout time delay
to desired setting. Each unit is shipped with a detailed Installation guide.
Specifications:
Ov ervoltage Protection
Input
• Voltage dropout: +12.5%
• Line voltage: 95-270 VAC
• Voltage pickup: +7.5%
• Control voltage: 18-240 VAC/VDC
Mechanical
• Line frequency: 50 or 60 Hz
Output
• Terminations: .25” male quick-connect terminals
• Type: relay energized upon acceptable line conditions
Response Times
• Form: single pole double throw (SPDT)
• Line dropout: .05 sec. (typical)
• Ratings: n.o.-5 amps, n.c.-5 amps
• Control voltage dropout: .07 sec. (typical)
Underv oltage Protection
• Line voltage sag (20%): .5 sec (typical)
• Voltage dropout: -12.5%
• Turn-on: 5 sec. (typical)
• Voltage pickup: -7.5%
Lockout Delay Timer Time delay: adj. 6-600 sec. (+/- 20%)
Env ironmental
• Transient protection: meets IEEE 587 standards for categories A & B without false output or degradation
(6Kv 0.5 µs x 100 KHz ring wave)(6Kv 1.2 x 50 ms impulse wave)
Dimensions: 3.25” x 3” x 1.25”
SOURCE 1 PART NO.
REPLACES
MLP $
S1-ICM491
A-1: EAC-401, 402, 403, 404 DIVERSIFIED: CV-100-RS, CV-200-RS15, CV-200-RS20 MARS: 32522, 32524, 32526
WAGNER/DIVERSITECH: DSP-1
75.86
133
HVAC Components
LINE MONITORS
ICM Single Phase Digital Line Monitors Series 492
Features:
• Protects Against Over and Under Voltage, and Rapid
Short Cycling caused by Transient Faults and Power
Interruptions
• Easy-view, Backlit Digital Display
• RMS Voltage Monitoring
• Adjustable Voltage Set Point
• Adjustable Over Voltage Setting
• Adjustable Under Voltage Setting
Specifications:
User Adj ustable Settings:
• Voltage set point: 95-280V
• Anti-short cycle time delay: 0-720 seconds
• Over voltage setting: 5-25%
• Under voltage setting: 5-25%
• Control mode: On and Off
• Response time: 0.1 to 10 seconds
Inputs:
• Line Voltage: 80 to 300 VAC
• Accuracy: ±2%
• Low Power Consumption: max 50 mA @ 120V,
max 100 mA @ 240V
• Control Voltage: 24 to 240 VAC
•
•
•
•
•
•
•
Adjustable Anti-Short Cycle Time Delay
Adjustable Response Time
Control Mode
5-Fault Memory
Universal Line voltage Input
Heavy Duty SPDT Relay Output
Universal Control Voltage Input (for integrating a
thermostat)
Output:
• Type: dry relay contacts
• Form: SPDT
• Relay Contact Ratings:
– N.C. Contacts: 10A resistive @ 277 VAC
– N.O. Contacts: 10A resistive @ 277 VAC
• Connection Terminals: 0.25” male fast-on
Mechanical:
• Case Dimensions: 3”L x 3.2”W x 1.35”H
• Unit Weight: 0.36 lbs.
Env ironmental:
• Operating temperature range: -30°C to +70°C
• Storage temperature range: -40°C to +85°C
• Max. Oper./Storage Relative Humidity: 95% noncondensing
SOURCE 1 PART NO.
DESCRIPTION
Description
MLP $
S1-ICM492
SINGLE PHASE, DIGITAL LINE VOLTAGE MONITOR
Single Phase Digital Line Monitors
127.75
ICM431 3-Phase Voltage Monitor
Three-phase line voltage monitor offering protection against phase loss/reversal, and unbalance; 50/60 Hz, 190-600 VAC (18-30
control VAC) - 8-pin plug in mount (base sold separately)
Specifications:
Voltage: 190-600 VAC
Frequency: 50/60 Hz
Control: 18-30 VAC
Output:
- Relay, SPST
- N.O. 10 amps
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ICM431
3-PHASE VOLTAGE MONITOR, PLUG IN MOUNT
85.11
ICM465 3-Phase Voltage Monitor
Three-phase line voltage monitor offering protection against phase loss/reversal, and unbalance; 50/60 Hz, 190-600 VAC (115 or
208/240 control VAC) - DIN rail mount
Specifications:
Voltage: 190-600 VAC
Frequency: 50/60 Hz
Control: 115 and 208/240 VAC
Output:
- Relay, SPST
- N.O. 10 amps
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ICM462
3-PHASE VOLTAGE MONITOR, DIN RAIL MOUNT
77.57
134
HVAC Components
TRANSFORMERS
Honeywell Voltage Control
Provide low voltage control of line voltage fan motors and auxiliary circuits in heating, cooling or heating-cooling circuits.
Features:
• NEMA standard Type D transformer (included) powers low voltage control systems.
• Provide overload protection for transformer.
• Convenient connections for thermostat, and heating-cooling equipment wiring.
• Mount on standard 4 x 4 junction box.
• Can be mounted in any indoor location without additional enclosure.
• Relay is easily replaced without disturbing wiring.
Specifications:
Application: For system with F50 Electronic Air Cleaner humidifier and blower motor.
Voltage: 120 VAC; 240 VAC; 208 VAC
Sw itching Action: DPDT
Horsepow er: 3/4 HP
Dimensions (in.): 4-1/2”H, 4-3/16”W, 3-3/32”D
Dimensions (mm): 114 mm H, 106 mm W, 79 mm D
Approv als, Underw riters Laboratories Inc: UL Listed
Approv als, Canadian Standards Association: Certified
Approv als, NEMA Standard: NEMA Standard DC20-1992
ELECTRICAL
RATINGS FULL
LOAD
SOURCE 1 PART NO.
ELECTRICAL RATINGS W
S1-R8239B1076
12 W MAXIMUM
120 VAC 240 VAC 120 VAC
12 A
6.9 A
COIL RATINGS
INRUSH
COIL RATINGS
SEALED
POWER SUPPLY
240 VAC
MAX
NOM
MAX
NOM
VAC
SECONDARY
MLP $
41.4 A
20 VA
17 VA
10 VA
9 VA
50 VA
26.5 V
129.68
ELECTRICAL
RATINGS LOCKED
ROTOR
72 A
Source 1 Class 2 Transformers - 90-T40S1 thru 90-T75C3 24 Volt Secondary Class 2 Transformers
Energy Limiting
Air conditioning, heating and refrigeration replacements.
Foot mounted-4" x 4" plate-conduit hub.
Source 1 multi-mounting control transformers are designed especially for the air conditioning market. The 24 volt output of the transformer assures the
operation of valves, relays and contactors under most low voltage conditions, eliminating call backs due to brown outs.
Class 2 transformers are used for industrial, heating and air conditioning controls applications.
Foot-Mount (Open Construction)
SOURCE 1 PART NO.
S1-T2404F
MARS PART JARD PART
NO.
NO.
50354
4031F
VA
HZ
PRIMARY
CONN
SEC.
CONN
MLP $
40
60
120/208/240V
LEADS
24V
LEADS
21.21
* M anual reset
Multi-Mount (Closed Construction) Universal Mounting With Plate
SOURCE 1 PART NO.
S1-T3501M
S1-T6753
S1-T7752
MARS
JARD PART
PART NO.
NO.
50304
4031M
50314
5031M
VA
HZ
50
75
75
50/60
50/60
Source 1 Transformer Lead Color Coding
PRIMARY SIDE
COMMON
120V
208V
240V
WHITE
BLACK RED
ORANGE
135
PRIMARY
CONN
SEC.
CONN
MLP $
120/208/240V
LEADS
24V
LEADS
24.82
120/208/240/480V
120/208/240/480V
LEADS
24V
24V
LEADS
37.32
40.18
SECONDARY SIDE
COMMON
24V
YELLOW
YELLOW
HVAC Components
TRANSFORMERS
Steveco Fan Control Centers
A one package transformer and relay combination, for remote mounting. They incorporate the over/under bobbin wound energylimiting class 2 transformer and fan relay on a common plate for mounting on a standard four inch junction box.
For use in remote control circuits:
• Furnace and air conditioners
• Operation of relays, contactors and solenoids
• Temperature indicating and regulation equipment
Ease of installation
• Line voltage connections pre-wired
• Color coded pre-stripped leads
• Low voltage connections on terminal board
TRANSFORMER PRIMARY
SOURCE 1 PART NO.
TRANSFORMER SECONDARY
CONTACT
RATINGS 120
VAC (AMPS)
VOLT
CONN.
VOLT
CONN.
RELAY
S1-90-112
MARS
NO.
24010
120V
24V
24013
120V
S1-90-118E
24012
120V
TERMINAL BOARD WITH 5
SCREW TERMINALS
SCREW TERMINALS
SCREW TERMINALS
DPDT
S1-90-113
COLOR CODED LEADS,
PRE-STRIPPED
COLOR CODED LEADS,
PRE-STRIPPED
COLOR CODED LEADS,
PRE-STRIPPED
24V
24V
CONTACT
RATINGS 240
VAC (AMPS)
FULL LOCKED FULL LOCKED
LOAD ROTOR LOAD ROTOR
13.8
82.8
6.9
41.4
MLP $
81.00
SPDT
13.8
82.8
6.9
41.4
57.39
SPNO/SPNC
13.8
82.8
6.9
41.4
57.96
* Can be used as an isolation relay/transformer for multi-stage digital thermostats when required.
White Rodgers Transformers
SOURCE 1 PART NO.
DESCRIPTION
VA
Hz
PRIMARY
CONN.
SEC.
CONN.
MLP $
S1-90-T40M2
MULTI-MOUNT (CLOSED CONSTRUCTION)
UNIVERSAL MOUNTING WITH PLATE:
90-T40M2
FOOT-MOUNT (MANUAL RESET, OPEN
CONSTRUCTION): 90-T50C3
40
60
120V
Leads
24V
Leads
32.11
50
50/60
120/208/240V
Leads
24V
Leads
62.75
60
50/60
120/208/240V
Leads
24V
Leads
72.71
75
50/60
120/208/240V
Leads
24V
Leads
94.89
S1-90-T50C3
S1-90-T60C3
S1-90-T75C3
Honeywell AT150 General Purpose Transformers
With 9" Lead Wires and Plastic End Caps
Honeywell AT150 general purpose transformers power 24Vac circuits.
Features:
• Color-coded lead wires for primary connections and screw terminals for secondary connections
• Includes fixed 1/4 inch (6mm) male quick-connects (AT150A models only) or color-coded lead wires for primary and secondary
connections
• Meets Underwriters Laboratories Standard UL 1585
• Identified Class 2 not wet, Class 3 wet
ELECTRICAL RATINGS
SOURCE 1 PART
NO.
S1-AT150B1252
PRIMARY FREQ (HZ) OUTPUT
SEC
VOLTAGE
VOLTAGE
24 V AT 50 27.5 V.O.C.
277 VAC
50/60
VA
DIMENSIONS
TEMPERATURE RATINGS
MLP $
1-11/16” H X 3-1/2” W X 1-3/4” D (43 MM H X 89 MM W X 75
MM D)
–20ºF TO +105ºF –29ºC TO +41ºC
37.25
136
HVAC Components
TRANSFORMERS
Honeywell Foot Mounted 120 VAC Transformer
With 9" Lead Wires
Honeywell AT20 transformers power 24V systems including thermostats, gas valves and relays.
Features:
•
•
•
•
•
Channel frame mounting feet and slots allow for three mounting positions
Features color-coded leadwires for primary connections
Overload protection provided
Energy limiting, meet NEMA DC20-1992 Standard
Meet NEC Class 2 not wet, Class 3 wet and UL 1585 requirements
ELECTRICAL RATINGS
SOURCE 1 PART NO.
FREQUENCY
PRIMARY VOLTAGE
SECONDARY VOLTAGE
OUTPUT
MLP $
S1-AT20A1123
S1-AT40A1121
60 HZ; 50 HZ
60 HZ; 50 HZ
120 VAC
120 VAC
26.5 V.O.C.
26.5 V.O.C.
24 VAC AT 19 VA
24 VAC AT 19 VA
49.86
52.79
Honeywell Foot Mounted 120/208/240 VAC Transformer
With 9" Lead Wires and Metal End Bells
Provide power to 24 VAC circuits in heating/ cooling control systems. Intended for use in systems with predictable, uniform loads Can
be used in any application that does not exceed the listed ratings.
Features:
• Rated at 40 VA.
• Color-coded leadwires for primary connections and screw terminals for secondary connections, fixed 1/4 inch
(6 mm) male quick-connects or color-coded leadwires for both primary and secondary, are standard.
• Meet NEC Class 2 requirements. Meet Underwriters Laboratories Inc. Standard UL 1585 and are identified. Class 2 not wet, Class
3 wet.
Specifications:
Mounting Foot mounted, plate mounted on 2” x 4" or 4” x 4" outlet box, clamp mounted using outlet box knockout, or panel mounted.
Temperature Ratings (F): –20°F to +105°F
Temperature Ratings (C): –29°C to +41°C
Approv als, Underw riters Laboratories Inc UL Listed: A,C,F models. File # E14881
Approv als, Canadian Standards Association CSA Certified: A & B models.
ELECTRICAL RATINGS
SOURCE 1 PART
NO.
S1-AT140A1018
ELECTRICAL CONNECTIONS
FREQ
PRIMARY VOLTAGE
SECONDARY VOLTAGE
OUTPUT
PRIMARY
SECONDARY
MLP $
60 HZ
120 VAC, 208 VAC, 240 VAC
27 V.O.C.
24 VAC AT 40 VA
9 IN. LEADWIRES (229 MM)
2 SCREW TERMINALS
37.50
Honeywell Foot Mounted 277 VAC Transformer
With 12" Lead Wires
Honeywell AT87 powers 24V air conditioning circuits and other applications that do not exceed the listed ratings.
Features:
•
•
•
•
Meets NEC Class 2 not wet, Class 3 wet and UL 1585 requirements
Transformer marked NEMA Type E
Overload protection provided
Color-coded leadwires for primary connections
ELECTRICAL RATINGS
SOURCE 1 PART NO.
FREQUENCY
PRIMARY VOLTAGE
SECONDARY VOLTAGE
OUTPUT
MLP $
S1-AT87A1189
60 HZ; 50 HZ
277 VAC
26.5 V.O.C.
24 VAC AT 48 VA
82.79
137
HVAC Components
TRANSFORMERS
Honeywell R8239 Control Center
Include NEMA standard transformer for excellent voltage control. Provide low voltage control of line voltage fan motors and auxiliary
circuits in heating, cooling or heating-cooling circuits.
Features:
• NEMA standard Type D transformer (included) powers low voltage control systems.
• Provide overload protection for transformer.
• Convenient connections for thermostat, and heating-cooling equipment wiring.
• Mount on standard 4 x 4 junction box.
• Can be mounted in any indoor location without additional enclosure.
• Relay is easily replaced without disturbing wiring.
• Includes relay enclosures.
Specifications:
Applications: For system with F50 Electronic Air Cleaner humidifier and blower motor.
Includes: R8222D
Approv als: NEMA Standard DC20-1992, UL listed, CSA Certified.
Dimensions: 4-1/2”H x 4-3/16”W x 3-3/32”D (114 mm H x 106 mm W x 79 mm D)
Electrical Ratings (W): 12 W maximum
Horsepow er: 3/4 hp @ 120 VAC, 3/4 hp @ 240 VAC
POWER SUPPLY
SOURCE 1 PART
NO.
S1-R8239B1076
S1-R8239B1043
PRIMARY
FULL LOAD
VAC
120 VAC, 208 VAC, 240 VAC
120 V
COIL RATINGS
LOCKED
ROTOR
SEC
120 240 120
240 SWITCH
VAC VAC VAC VAC ACTION
50 VA 26.5 V 12 A 6.9 A 72 A 41.4 A DPDT
40 VA 26.5 V 12 A 6.9 A 72 A 41.4 A DPDT
INRUSH
SEALED
MLP $
20 VA MAXIMUM, 17 VA NOMINAL
20 VA MAXIMUM 17 VA NOMINAL
129.68
107.50
Honeywell Standard Transformer
24V control circuit step-down transformer designed to power any 24V control system, including thermostats, gas valves and relays.
Features:
• Energy limiting, meets NEMA Standard DC20-1992. Transformer is marked “NEMA Type D.”
• Meets “NEC Class 2 not wet, Class 3 wet” and U.L. 1585 requirements.
• Mount within proper enclosure.
Specifications:
Electrical Connections (Primary): 9” (229 mm) lead wires.
Electrical Connections (Secondary): (2) screw terminals.
Mounting: can be foot-mounted; plate-mounted on 4”x4”, 4” octagon, or 2”x4” electrical boxes (transformer all above plate or 3/4
above plate); or clamp-mounted via a junction box knockout.
Approv als: UL Component Recognized. CS Certified, N.E.C. Approved.
ELECTRICAL RATINGS
SOURCE 1 PART
NO.
S1-AT72D1683
PRIMARY VOLTAGE
S1-AT72D1691
208 V, 240 V W/40 VA
OUTPUT RATING
120 V
FREQ
(HZ)
50/60
50/60
OUTPUT
24 V AT
40 VA
24 V AT
40 VA
SEC
VOLT
26.5
V.O.C.
26.5
V.O.C.
DIMENSIONS
TEMPERATURE RATINGS
MLP $
3-7/32” H X 2-7/32” W X 3-1/16” D (81.8 MM H X 56.4 MM W X 77.8
MM D)
3-7/32” H X 2-7/32” W X 3-1/16” D (81.8 MM H X 56.4 MM W X 77.8
MM D)
53.18
61.21
138
—NOTES—
139
—NOTES—
140
—NOTES—
141
—NOTES—
142
—NOTES—
143
—NOTES—
144
Indoor Air Quality
RESIDENTIAL AIR FILTRATION SYSTEMS
Premium Hybrid Media/Electronic Air Cleaners
Features:
• Whole home electronic air cleaner utilizes both the electrostatic attraction and filter media to provide a more consistent, higher level
of performance.
• Equivalent to MERV16 efficiency
• System matching appearance
• When new:
- 97.8% effective at removing particles from 3-10 microns
- 95.7% effective at removing particles from 1-3 microns
- 92.0% effective at removing particles from 0.3-1.0 microns
• Rated to 2000CFM
• Support up to 400 lbs
• Low airflow resistance:
- 0.10" w.g. @1000 cfm
- 0.29" w.g. @ 2000 cfm
• Easy maintenance:
• Replace filter media once per year.
- No washing of cells required; only wiping down of ionizing wires
• Power usage does not exceed 60 watts
• UL Listed
• Silent operation; no snapping from the electronic charge of particles
SOURCE 1 PART NO.
BRAND
MLP $
S1-HEAC3000T
SOURCE 1, YORK, COLEMAN, LUXAIRE, FRASER-JOHNSTON
1318.39
Media
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-FM501
HEAC3000 ELECT-HYBRID MEDIA
71.71
Source 1 High Efficiency Expandable Media Air Cleaners
Features:
• The whole home media air cleaner permanently traps particles, including airborne contaminants, down to 1 micron (1 millionth of a
meter) in size. Particles of less than 6 microns are invisible to the naked eye, and allergy-causing particles and mold spores range
from 0.5 microns to 1 micron.
• Helps minimize the risk of asthma and allergy attacks
• Up to 2 year filter media life
• Low static pressure drop
• MERV 10 or MERV 13 efficiency rating
• 5-year limited warranty
SOURCE 1 PART NO.
DESCRIPTION
BRAND
MERV RATING
MLP $
S1-TM11PAC16252
16” x 25” WHOLE HOME EXPANDABLE MEDIA AIR CLEANER
11
205.36
S1-TM11PAC20202
11
205.36
S1-TM11PAC20252
11
205.36
S1-TM13PAC16252
13
266.07
S1-TM13PAC20202
13
266.07
S1-TM13PAC20252
SOURCE 1, YORK, COLEMAN,
LUXAIRE, FRASER-JOHNSTON
13
266.07
Replacement Media for Expandable Media Air Cleaners
SOURCE 1 PART NO.
FOR MODEL NO.
STD. PKG.
MASTER CARTON QTY.
MLP $
S1-FM11162506
S1-FM11202506
S1-FM201
S1-FM210
S1-FM213
S1-FM310
S1-FM313
S1-FM401
S1-FM410
S1-FM413
S1-FM613
S1-MAC11162506, AC24, APRILAIRE 2400
S1-MAC11202506, AC22
S1-WHM10202505, APRILAIRE 2200
S1-TM11PAC20252, APRILAIRE 1210
S1-TM13PAC20252, APRILAIRE 4200, 3210, 2210
S1-WHM10162505, APRILAIRE 2400
16 x 25 COMPETITORS' UNITS WITH S1-4897
ADAPTER KIT
20 x 25 COMPETITORS' UNITS WITH S1-4897
ADAPTER KIT
1
1
1
1
1
1
1
1
1
1
1
9
9
10
8
8
8
8
10
8
8
8
65.89
65.89
56.14
75.36
89.46
70.64
84.75
53.57
70.64
84.75
87.50
1
8
87.50
S1-FM813
145
Indoor Air Quality
Source 1 High Efficiency Expandable Media Air Cleaners
Media Upgrade Kits for Source 1 and Competitors Air Cleaners
SOURCE 1 PART NO.
FOR MODEL NO.
STD. PKG.
MASTER CARTON QTY.
MLP $
S1-FRKIT1213
CONVERTS S1-WHM10202506 AND APRILAIRE 2200
TO ACCEPT S1-FM213 MEDIA
CONVERTS S1-WHM10162506 AND APRILAIRE 2400
TO ACCEPT S1-FM413 MEDIA
CONVERTS S1-*M*PAC2025 TO ACCEPT S1-FM210
OR S1-FM213 MEDIA
OR S1-FM313 MEDIA
OR S1-FM413 MEDIA
CONVERTS COMPETITORS' UNITS TO ACCEPT
S1-FM613 OR S1-FM813 MEDIA
1
6
114.29
1
6
114.29
1
8
24.36
1
8
24.36
1
8
24.36
1
8
24.36
S1-FRKIT1413
S1-FRKIT213
S1-FRKIT313
S1-FRKIT413
S1-FRKIT4897
Source 1 MERV10 High Efficiency Media Air Cleaners
Replacement Media For Honeywell F50 Series Electronic Air Cleaners
SOURCE 1 PART NO.
LENGTH
USE IN AIR CLEANER MODELS
MLP $
S1-136434AA
S1-136434BA
20 IN.
16 IN.
F50A, F50E, F50F, F57A, B, F58F AND F70C
F50A, F50E, F50F, F59A
24.75
24.75
Replacement Cartridges for MAC10Series MERV10 Media Air Cleaners
SOURCE 1 PART NO.
DESCRIPTION
S1-FM10162505
S1-FM10202005
S1-FM10202505
MERV10 REPLACEMENT CARTRIDGE MEDIA
SIZE
(INCHES)
16 X 25 X 5
20 X 20 X 5
20 X 25 X 5
REPLACES
STD.
PKG.
6
6
6
PALLET
QTY.
54
54
54
MLP $
SIZE
(INCHES)
16 X 20
REPLACES
PALLET
QTY.
80
MLP $
HONEYWELL FC100A1003
STD.
PKG.
5
16 X 25
5
60
44.14
20 X 20
5
80
44.14
20 X 25
5
60
46.00
—
—
—
40.57
42.39
42.39
Replacement Media For Honeywell Air Cleaners
SOURCE 1 PART NO.
DESCRIPTION
S1-FM10162005HW
MERV10 CARTRIDGE MEDIA FOR HONEYWELL AIR
CLEANERS
CLEANERS
CLEANERS
CLEANERS
S1-FM10162505HW
S1-FM10202005HW
S1-FM10202505HW
44.14
Replacement Media for Honeywell FH8000 Series TrueCLEANTM Air Cleaners
SOURCE 1 PART NO.
DESCRIPTION
CARTON MULTIPLE
MLP $
S1-FR8000A2020
S1-FR8000A2520
S1-FR8000F1625
S1-FR8000F2025
REPLACEMENT MEDIA FOR FH8000A2020
REPLACEMENT MEDIA FOR FH8000A2520
REPLACEMENT MEDIA FOR FH8000F1625
REPLACEMENT MEDIA FOR FH8000F2025
5
5
5
5
160.21
160.21
160.21
160.21
ClenAir Aprilaire & Spacegard Replacements
These Merv 11 filter media are direct replacement for the Aprilaire Spacegard 201 and 401. The new string-less, glued pleat spacing
design makes for an easier and faster installation. These replacement filters can be used in the hundreds of thousands of installed
Spacegard filters across the U.S., and compact package and repeat business make them a contractor favorite.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-NC-61256
S1-NC-61257
Use with Aprilaire & Spacegard 2200 & 2250
Use with Aprilaire & Spacegard 2400
6
6
61.61
61.68
146
Indoor Air Quality
Honeywell PopUP Replacement Filter Media
Honeywell PopUP filters store flat and pop into shape for installation.
Features:
• MERV 11 efficiency
• Save space on the truck.
• Less damage during storage, Save time on assembly.
• So easy you can sell over-the-counter to homeowners without worry of mistakes.
• Compact shape makes PopUP easy to ship.
• No combs, pleat spacers or end caps.
SOURCE 1 PART NO.
DESCRIPTION
SHIPPING MULTIPLE
MLP $
S1-POPUP1620
S1-POPUP1625
S1-POPUP2020
S1-POPUP2025
S1-POPUP2200
S1-POPUP2400
16 x 20
16 x 25
20 x 20
20 x 25
FITS APRILAIRE 2200
FITS APRILAIRE 2400
12
12
12
12
12
12
76.07
76.07
76.07
74.25
69.25
69.25
147
Pleated Filters
Purolator Key Pleat Filters
The Key Pleat® self supported pleated filter has a MERV 8 rating. The filter is made of 100% synthetic media. The media pack is contained in a single piece
beverage board. Self-supported Key Pleat filters eliminate the need for a metal backing to shape the pleats. They are fully incinerable, simplifying disposal.
Key Pleat is available in 1" and 2" Standard Capacity and 1", 2" and 4" High Capacity.
Features:
•
•
•
•
MERV 8 efficiency
Standard or High Capacity
Self-Support Pleat Filter
Key Pleat filters are classified U.L. Class 2 per U.L. Standard 900 for flammability only
SOURCE 1 PART NO.
SHIPPING MULTIPLE
DESCRIPTION
CAPACITY
MLP $
S1-PF8-1020-1
S1-PF8-1020-2
S1-PF8-1024-1
S1-PF8-1212-1
S1-PF8-1220-1
S1-PF8-1220-2
12
12
12
12
12
12
10X20X1
10X20X2
10X24X1
12X12X1
12X20X1
12X20X2
STANDARD
STANDARD
STANDARD
STANDARD
STANDARD
STANDARD
7.04
7.86
9.18
8.32
6.89
8.71
S1-PF8-1224-1
S1-PF8-1224-2
S1-PF8-1224-4
S1-PF8-1414-1
S1-PF8-1420-1
S1-PF8-1420-2
S1-PF8-1424-1
S1-PF8-1425-1
S1-PF8-1425-2
S1-PF8-1425-4
S1-PF8-1430-1
S1-PF8-1520-1
S1-PF8-1520-2
S1-PF8-1616-1
S1-PF8-1616-2
S1-PF8-1620-1
S1-PF8-1620-2
S1-PF8-1620-4
S1-PF8-1624-1
S1-PF8-1624-2
S1-PF8-1625-1
S1-PF8-1625-2
S1-PF8-1625-4
S1-PF8-1630-1
S1-PF8-1818-1
S1-PF8-1818-2
S1-PF8-1820-1
S1-PF8-1820-2
S1-PF8-1824-1
S1-PF8-1824-2
S1-PF8-1824-4
S1-PF8-1825-1
S1-PF8-1825-2
S1-PF8-2020-1
S1-PF8-2020-2
S1-PF8-2020-4
S1-PF8-2022-1
S1-PF8-2024-1
S1-PF8-2024-2
S1-PF8-2024-4
S1-PF8-2025-1
S1-PF8-2025-2
S1-PF8-2025-4
S1-PF8-2030-1
S1-PF8-2030-2
S1-PF8-2424-1
S1-PF8-2424-2
S1-PF8-2424-4
12
12
6
12
12
12
12
12
12
6
12
12
12
12
12
12
12
6
12
12
12
12
6
12
12
12
12
12
12
12
6
12
12
12
12
6
12
12
12
6
12
12
6
12
12
12
12
6
12X24X1
12X24X2
12X24X4
14X14X1
14X20X1
14X20X2
14X24X1
14X25X1
14X25X2
14X25X4
14X30X1
15X20X1
15X20X2
16X16X1
16X16X2
16X20X1
16X20X2
16X20X4
16X24X1
16X24X2
16X25X1
16X25X2
16X25X4
16X30X1
18X18X1
18X18X2
18X20X1
18X20X2
18X24X1
18X24X2
18X24X4
18X25X1
18X25X2
20X20X1
20X20X2
20X20X4
20X22X1
20X24X1
20X24X2
20X24X4
20X25X1
20X25X2
20X25X4
20X30X1
20X30X2
24X24X1
24X24X2
24X24X4
STANDARD
STANDARD
HIGH
STANDARD
STANDARD
STANDARD
STANDARD
STANDARD
STANDARD
HIGH
STANDARD
STANDARD
STANDARD
STANDARD
STANDARD
STANDARD
STANDARD
HIGH
STANDARD
STANDARD
STANDARD
STANDARD
HIGH
STANDARD
STANDARD
STANDARD
STANDARD
STANDARD
STANDARD
STANDARD
HIGH
STANDARD
STANDARD
STANDARD
STANDARD
HIGH
STANDARD
STANDARD
STANDARD
HIGH
STANDARD
STANDARD
HIGH
STANDARD
STANDARD
STANDARD
STANDARD
HIGH
7.36
7.82
12.93
9.07
7.00
8.25
9.61
7.79
9.29
43.00
11.68
7.61
8.21
8.82
10.14
6.86
7.18
13.86
9.71
9.18
7.50
8.14
15.46
12.29
9.89
11.14
9.36
11.36
10.43
10.07
20.07
11.11
10.93
7.46
8.11
16.68
10.86
10.96
10.43
17.93
8.64
9.36
18.43
11.32
12.43
10.57
10.61
19.75
148
Indoor Air Quality
Pleated Filters
Purolator Key Pleat Filters
SOURCE 1 PART NO.
SHIPPING MULTIPLE
DESCRIPTION
CAPACITY
MLP $
S1-PF8-2430-1
S1-PF8-2525-1
S1-PF8-2525-2
12
12
12
24X30X1
25X25X1
25X25X2
STANDARD
STANDARD
STANDARD
17.21
11.86
12.89
ClenAir HVAC Carbon Block
The HVAC Carbon Block can be added to any ducted HVAC System to immediately remove odor and provide
cleaner, healthier air to any indoor environment. Using a unique combination of carbon and minerals, the HVAC
Carbon Block absorbs many odors and harmful chemical pollutants found in the air inside homes, offices, and
other buildings. Simply install the HVAC Carbon Block in the air handler against the outlet side of the existing air
filter. A percentage of the system air will pass through the HVAC Carbon Block and over time, all of the system
air will be filtered by the HVAC Carbon Block.
HVAC Carbon Block removes many indoor air pollutants including: animal odors, food odors, ozone, tobacco
smoke, formaldehyde, body odors, paint fumes, auto exhaust, sewer gases, burnt odors, cleaning chemicals,
chlorine, turpentine, cosmetics, mercaptans, ammonia, solvents, alcohol, acetone, printer gases, VOC’s, smog,
mildew, and hospital odors.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-NC-61062
9½” x 10” x 1½” Carbon Block
6
102.50
Indoor Air Quality
RESIDENTIAL AIR PURIFIERS
Premium UV Air Purifiers with Status Indicator LED
Replacement Lamps
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-LAPS120A
S1-LAPS220A
REPLACEMENT UV LAMP WITH POWER SUPPLY, 115 V
REPLACEMENT UV LAMP WITH POWER SUPPLY, 230V
213.43
225.54
Source 1 UV Air Purifiers
Replacement Ultra Violet “C” Lamps
SOURCE 1 PART NO.
FOR MODEL NO.
STD. PKG.
MASTER CARTON QTY
MLP $
S1-UC100E1006
S1-UC100E1030
S1-UVLAMP22024
S1-UVLAMP36120
S1-UVLAMP36120HW
S1-UVLAMP50120
UV100E1001, UV100E1043
UV100E1035, UV100E3007
S1-UV22024
S1-UV36120
S1-UV100A1083
S1-UV50120
1
1
1
1
1
1
1
1
10
10
N/A
10
223.61
207.04
156.50
142.29
135.68
177.82
149
Indoor Air Quality
RESIDENTIAL HUMIDIFIERS
Premium Bypass and Flow-Through Humidifiers
Bypass and Flow-Through
SOURCE 1 PART NO.
DESCRIPTION
BRAND
S1-BP4000MT
S1-BP5000MT
S1-BP6000MT
S1-FP7000MT
DRAINLESS BYPASS HUMIDIFIER W/MANUAL H'STAT
BYPASS HUMIDIFIER WITH MANUAL HUMIDISTAT
BYPASS HUMIDIFIER WITH MANUAL HUMIDISTAT
POWER HUMIDIFIER WITH MANUAL HUMIDISTAT
LUXAIRE, COLEMAN
LUXAIRE, COLEMAN
LUXAIRE, COLEMAN
LUXAIRE, COLEMAN
ELECTRICAL
RATING
24 VAC
24 VAC
24 VAC
120 VAC
GPD
MLP $
17
12
17
18
392.86
303.57
339.29
517.86
Premium Humidifiers
Replacement Water Pads
SOURCE 1 PART NO.
DESCRIPTION
STD. PKG.
MASTER CARTON QTY.
MLP $
S1-HUPAD10
S1-HUPAD35
S1-HUPAD45
VAPOR PAD FOR S1-BP5000
VAPOR PAD FOR S1-BP6000 & S1-FP7000
VAPOR PAD FOR S1-BP4000
1
1
1
10
10
10
13.04
17.75
39.57
ClenAir Ultra Upgrade Humidifier Panel Replacements
Most home humidifiers waste a lot of water because the water panels do not absorb or hold any water. Most of the water flowing over
the metal panel goes right down the drain, costing homeowners money and wasting a precious resource. The ClenAir Ultra Upgrade
water panels are constructed of a special water absorbing material that allows more water to be evaporated into the heating system
and the home, and less water wasted down the drain. The result is a more efficient humidifier which will satisfy the humidity needs
more quickly with less wa ste, increasing the comfort level in the home, especially where the existing humidifier is undersized.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-NC-61254
S1-NC-61255
Ultra Upgrade Humidifier Panel Replacements - #10 Size
Ultra Upgrade Humidifier Panel Replacements - #35 Size
10
10
15.39
20.43
ClenAir Universal Humidifier Panels
ClenAir Universal Humidifier Panels provide optimum moisture output, performance, and durability. They replace
Aprilaire, Honeywell, Carrier, Bryant, Lennox, ICP, and others. Made from quality materials in the USA.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-NC-61250
S1-NC-61251
S1-NC-61252
ClenAir Universal Humidifier Panel - #10 Size
10
6
10
14.04
21.07
17.50
150
Indoor Air Quality
RESIDENTIAL HUMIDIFIERS
Icemaker Kit
Supplies water to most refrigerators with automatic icemakers, humidifiers and evaporative coolers. Contains self-tapping valve and
all necessary fittings.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-750-401
S1-750-402
ICEMAKER KIT – POLY TUBE – 25’
ICEMAKER KIT – COPPER – 25’
15.32
57.00
Polyethylene Tubing
F.D.A. approved, flexible, non-toxic tubing. Tasteless and odorless, lightweight, low density. Ideal for drinking water lines, evaporative
coolers, and radiant heating. I.D.: 11/64”, O.D.: 1/4”, Wall: 0.040, Max. W/P (in.) 150 PSI @ 70F.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-PE-104
POLYETHYLENE TUBING
100’/ROLL
35.43
Self Tapping Water Valve
Installs on all copper tube lines from 3/8” O.D. to 1-1/8” O.D. without shutting off water. No drilling required. Features 1/4”
compression fitting. Stainless steel piercing needle. Special molded gasket seals on both tubing and valve. Will not slip or turn on
tubing.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-QAV-2
SELF TAPPING WATER TAP VALVE
9.07
Source 1 Steam Humidifiers
Steam Humidifier Replacement Cylinders & Accessory Options
SOURCE 1 PART NO.
DESCRIPTION
STD. PKG.
MLP $
S1-HUCYL12
S1-HUCYL20
S1-HUCYL20LC
S1-HUCYL6
REPLACEMENT STEAM CYLINDERS FOR S1-HU12DS & S1-HU12RD
REPLACEMENT STEAM CYLINDER FOR S1-HU20DS
REPLACEMENT STEAM CYLINDER FOR S1-HU20DSLC
REPLACEMENT STEAM CYLINDERS FOR S1-HU6DS & S1-HU6RS
1
1
1
1
264.36
392.86
392.86
264.36
Steam Humidifiers
Residential Steam Humidifier - For applications when evaporative units are less practical (attics, crawl spaces,
closets, milder winter climates, non-forced air heating source).
SOURCE 1 PART NO.
DESCRIPTION
CAPACITY
ELECTRICAL DATA
DIMENSIONS
MLP $
S1-STEAM8000T01
HUMIDIFIER,STEAM,RESIDENTIAL
11.5,20.5, 23.5 GPD
120V, 208V,240V -60HZ 11.5A
10.13" X 18.0" X 7.13"
1853.57
RESIDENTIAL DEHUMIDIFIERS
Central Dehumidifiers
Provide dedicated moisture removal more efficiently than your air conditioner. Installed as part of your home’s heating and cooling
sy stem, a central dehumidifier pulls air from every room through the return ducts. Then it removes moisture and cycles dry air back
throughout your home.
SOURCE 1 PART NO.
DESCRIPTION
CAPACITY
VENTILATION OPTION
DIMENSIONS
MLP $
S1-CD065T01
S1-CVD090T01
S1-CVD135T01
CENTRAL DEHUMIDIFIER,NO-VENT,65PTS/DAY
CENTRAL VENTILATING DEHUMIDIFIERS,90 PTS/DAY
CENTRAL VENTILATING DEHUMIDIFIERS,135 PTS/DAY
65 PINTS/DAY
90 PINTS/DAY
135 PINTS/DAY
NO
YES
YES
12.5" X 14.5" X 22"
20.5" X 19.5" X 24"
20.5" X 19.5" X 24"
2688.00
3120.00
4176.00
151
Indoor Air Quality
RECOVERY VENTILATORS
Source 1 Energy Recovery Ventilators
Includes: Labels for Source 1, York, Luxaire and Coleman brands.
Specifications:
Heat Exchanger Type: Cro ss-flow (enthalpic)
Voltage: 120 VAC at 60 Hz
Amperage: 1.5 A
Defrost Type: Evacuation
Certification: ARI 1060, cCSAusa
DIMENSIONS (INCHES)
SOURCE 1 PART NO.
OVERALL
HEAT EXCHANGER
CFM
S1-ERV160
S1-ERV220
23-7/8”L x 21-1/2”H x 11-3/8”W
23-7/8”L x 21-1/2”H x 16-1/2”W
12”L x 12”H x 10”W
12”L x 12”H x 15”W
30–160
50–220
EXCHANGER SURFACE (SQ. FT.) STD. PKG. PALLET QTY.
85
127
1
1
12
9
MLP $
2570.07
2936.68
Energy Recovery Ventilator Accessory
SOURCE 1 PART NO.
DESCRIPTION
STD. PKG.
MLP $
S1-ERVCTRLDLX
S1-ERVTIMER
DELUXE CONTROL
CONTROL TIMER
1
1
286.04
74.96
SOURCE 1 PART NO.
DESCRIPTION
STD. PKG.
MLP $
S1-ERVCTRLDLX
S1-ERVTIMER
DELUXE CONTROL
CONTROL TIMER
1
1
286.04
74.96
Source 1 Heat Recovery Ventilators
Heat Recovery Ventilator Accessory
Includes: Labels for Source 1, York, Luxaire and Coleman brands.
Specifications:
Heat Exchanger Type: Cro ss-flow (polypropylene)
Voltage: 120 VAC at 60 Hz
Amperage: 1.5 A
Defrost Type: Evacuation
Certification: HVI, cCSAus
DIMENSIONS (INCHES)
SOURCE 1 PART NO.
OVERALL
HEAT EXCHANGER
CFM
S1-HRV160
S1-HRV220
23-7/8”L x 21-1/2”H x 11-3/8”W
23-7/8”L x 21-1/2”H x 16-1/2”W
12”L x 12”H x 10”W
12”L x 12”H x 15”W
30–160
50–220
EXCHANGER SURFACE (SQ. FT.) STD. PKG. PALLET QTY.
104
150
1
1
12
9
MLP $
2040.21
2322.82
System Sensor Innovair® Series Photoelectric Duct Smoke Detectors
Features:
• Photoelectric, integrated low-flow technology
• Air velocity rating from 100 ft./min. to 4000 ft./min. (0.5 m/sec. to 20.32 m/sec.)
• Versatile mounting options: square or rectangular configuration
• Plug-in sensor offers superb false alarm immunity and the latest sensor technology
• Broad ranges for operating temperature (4°F to 158°F) and humidity (0% to 95% non-condensing)
• Patented sampling tube installs from front or back of the detector with no tools required
• Increased wiring space with a newly added 3/4-inch conduit knockout
• One easy-access Test/Reset button and improved LED status
• Patented interconnect feature for multi-fan shutdown
• New high-contrast terminal designations
• Built-in short-circuit protection from operator wiring errors
• Field-selectable settings for configuring the detector
• Two DPDT Form-C relay contacts
• 24 VAC/DC or 120 VAC
• Backward compatibility with existing Innovair products, including remote accessories
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-D4120
S1-D4120W
4-WIRE PHOTOELECTRIC LOW-FLOW DUCT SMOKE DETECTOR
4-WIRE PHOTOELECTRIC LOW-FLOW DUCT SMOKE DETECTOR WITH WATERPROOF
ENCLOSURE
257.68
393.79
152
Indoor Air Quality
RECOVERY VENTILATORS
Photoelectric Duct Smoke Detector Accessories
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-AOS
S1-APA151
S1-D4P120
S1-D4S
S1-DST1
S1-DST1.5
S1-DST10
S1-DST3
S1-DST5
S1-ETX
S1-MHR
S1-MHW
S1-RA100Z
S1-RTS151
S1-RTS151KEY
S1-RTS2
MINI-ALERT ADD-ON STROBE (WHITE)
REMOTE ANNUNCIATOR WITH PIEZO ALARM
4-WIRE PHOTOELECTRIC POWER BOARD COMPONENT ONLY, 24 VAC/DC, 120 VAC
4-WIRE PHOTOELECTRIC SENSOR COMPONENT ONLY
METAL SAMPLING TUBE DUCT WIDTH UP TO 1 FT. (0.3 M)
METAL SAMPLING TUBE DUCT WIDTHS 1 FT. TO 2 FT. (0.3 TO 0.6 M)
METAL EXHAUST TUBE DUCT WIDTH 1 FT. (0.3 M)
MINI-HORN, RED
MINI-HORN, WHITE
REMOTE ANNUNCIATOR ALARM LED
REMOTE TEST STATION
REMOTE TEST STATION WITH KEY LOCK
MULTI-SIGNALING ACCESSORY
87.29
58.21
194.32
181.82
10.00
13.32
49.21
18.71
23.29
10.00
27.04
27.04
33.29
70.64
102.89
174.57
SMOKE & GAS DETECTORS
Photoelectric Duct Smoke Detector Accessories
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-2D51
PHOTOELECTRIC SMOKE DETECTOR HEAD
101.00
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-55000-225
S1-55000-328
S1-STN-XT
REPLACEMENT IONIZATION SMOKE DETECTOR HEAD FOR SL-2000-N
REPLACEMENT PHOTOELECTRIC SMOKE DETECTOR HEAD FOR SL-2000-P
REPLACEMENT EXHAUST TUBE
95.50
103.61
2.04
SL-2000 Series Duct Smoke Detectors
Replacement Parts
Available in both Ionization & Photoelectric Versions
Features:
• Designed to maximize efficiency of installation and maintenance
• “No-Tools Required” system allows for front or rear loading and removal of sampling tubes
• “No-Tools Required” thumbscrews make cover removal a snap
• Patent pending “test port” allows for aerosol smoke testing without cover removal
• “Low-Flow Technology” SL-2000 is listed for velocities between 100–4,000 ft. per minute
SOURCE 1 PART NO.
VERSION
SPECIFICATIONS
APPLICATION
MLP $
S1-SL-2000-N
S1-SL-2000-P
IONIZATION
PHOTOELECTRIC
4-WIRE, UNIVERSAL VOLTAGE
HIGH TEMPERATURE
LOW-FLOW TECHNOLOGY
248.61
248.61
Accessories
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-STN-10.0
S1-STN-2.5
S1-STN-5.0
S1-TG-2000
S1-WP-2000
10.0’ SAMPLING TUBE
TEST GAS WITH TEST PORT NOZZLE FOR DUCT DETECTORS
WEATHERPROOF ENCLOSURE
27.11
13.57
15.82
38.61
231.61
153
Indoor Air Quality
SM-501 Series Duct Smoke Detectors
Available in both Ionization & Photoelectric Versions
Features:
• Compact design allows for installation in the tightest spots
• Trusted performance, rugged steel construction
• Specifically designed to link up to 30 detectors
SOURCE 1 PART NO.
VERSION
SPECIFICATIONS
MLP $
S1-SM-501-N
IONIZATION
269.54
Accessories
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-STS-10.0
S1-STS-2.5
S1-STS-5.0
S1-TG-1000
S1-WP-1
STD. TEST GAS SPRAY NOZZLE FOR SM-501 SERIES & OPEN AREA DETECTORS
WEATHERPROOF ENCLOSURE
26.71
13.57
15.82
43.71
170.68
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-STS-XT
REPLACEMENT EXHAUST TUBE
2.04
Replacement Parts
Horns/Strobes
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-SHP24-1575O
S1-SHP24-1575W
WHITE HORN/STROBE WITH OPAQUE LENS
WHITE HORN/STROBE WITH CLEAR LENS
150.36
140.43
MS Series Remote Accessories
Features:
• Made of attractive and durable stainless steel
• Provides visual and/or audible status notification
• Remote test/reset option available
• 15 versions available to meet your needs
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-MS-KA/P/R
S1-MS-KA/P/R/T
REMOTE ALARM LED (RED), PILOT (GREEN) & KEY-OPERATED TEST/RESET SWITCH
REMOTE TROUBLE LED (YELLOW), PILOT LED (GREEN) & KEY-OPERATED TEST/RESET
SWITCH
REMOTE ALARM LED (RED) & KEY-OPERATED TEST/RESET SWITCH
REMOTE ALARM LED (RED)
REMOTE TROUBLE LED (YELLOW), PILOT LED (GREEN) & PUSH-BUTTON TEST/RESET
SWITCH
REMOTE ALARM LED (RED) & PILOT LED (GREEN)
REMOTE ALARM LED (RED), PILOT LED (GREEN) & PUSH BUTTON TEST/RESET SWITCH
REMOTE TROUBLE LED (YELLOW), PILOT LED (GREEN)
REMOTE ALARM LED (RED) & PUSH-BUTTON TEST/RESET SWITCH
REMOTE DUCT SMOKE DETECTOR LED (RED)
REMOTE TROUBLE LED (YELLOW) & PILOT LED (GREEN)
REMOTE ALARM HORN
REMOTE ALARM HORN, ALARM LED (RED), TROUBLE LED (YELLOW), PILOT LDED (GREEN)
& KEY-OPERATED TEST/RESET SWITCH
REMOTE ALARM HORN, ALARM LED (RED), PILOT LED (GREEN) & KEY-OPERATED
TEST/RESET SWITCH
REMOTE ALARM HORN, ALARM LED (RED) & PILOT LED (GREEN)
76.79
89.39
S1-MS-KA/R
S1-MS-RA
S1-MS-RA/FT/P
S1-MS-RA/P
S1-MS-RA/P/R
S1-MS-RA/P/T
S1-MS-RA/R
S1-MS-RD
S1-MS-RD
S1-MS-RH
S1-MS-RH/KA/P/A/T
S1-MS-RH/KA/P/R
S1-MS-RH/P/A
154
65.82
22.50
31.32
21.93
30.71
25.00
26.32
24.39
24.39
39.50
109.71
121.39
43.89
Indoor Air Quality
T-PB Series 24VAC Power Supplies
Features:
• 24VAC output switch with status LED
• 4.0A, 96VA (Class I) and 3.0A, 72VA (Class II) versions available
• 115VAC @ 5.0A convenience outlet located on the front panel
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-T-PB-202-0
S1-T-PB-202-1
POWER SUPPLY, 100VA, 24VAC @ 4.0A, CLASS 1 CHASSIS
POWER SUPPLY, 100VA, 24VAC @ 4.0A, CLASS 1 CHASSIS WITH ENCLOSURE
142.21
170.68
Audible/Visible Notification
System Sensor SpectrAlert Advance Series: HR-LF / HW-LF
The SpectrAlert Advance HR-LF is a two-wire, 12/24 volt, low frequency sounder for wall or ceiling installation.
Specifications:
•
•
•
•
•
•
Voltage: Regulated 12DC/FWR or regulated 24DC/FWR
Operating Voltage Range: 8 to 17.5 V (12V nominal) or 16 to 33 V (24 nominal)
Wiring Gauge: 12 to 18 AWG
Operating Temperature: –40°F to 151°F (–40°C to 66°C)
Humidity Range: 10 to 93% non-condensing
Dimensions: 5.6"L x 4.7"W x 1.3"D (142mm L x 119mm W x 33mm D)
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-HR-LF
S1-HW-LF
SOUNDER,LOW FRQ,RED
SOUNDER,LOW FRQ,WHITE
130.14
130.14
System Sensor SpectrAlert Advance Series: P2RH-LF / P2WH-LF
The SpectrAlert Advance P2RH-LF is a two-wire, 24 volt, low frequency sounder strobe with selectable high-candela strobe settings of
135, 150, 177 and 185 cd for wall or ceiling installation.
Specifications:
•
•
•
•
•
•
•
•
Voltage: Regulated 24DC/FWR
Candela: Selectable high-candela strobe settings of 135, 150, 177 and 185 cd
Operating Voltage Range: 16 to 33 V (24 nominal)
DC Max. Operating Current: 16 to 33 V (24 nominal)
Wiring Gauge: 12 to 18 AWG
Operating Temperature: –40°F to 151°F (–40°C to 66°C)
Humidity Range: 10 to 93% non-condensing
Wall mount dimensions (including lens): 6.4"L x 4.7"W x 2.5"D (162mm L x 119mm
W x 64mm D)
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-P2RH-LF
S1-P2WH-LF
SOUNDER STROBE,WALL,LOW FRQ,HIGH CD,RED
SOUNDER STROBE,WALL,LOW FRQ,HIGH CD,WHITE
239.36
239.36
BRK Electronics Carbon Monoxide and Smoke Alarms
9V Battery Electrochemical Carbon Monoxide Alarm with Silence
Features:
• Electrochemical CO sensor
• Silence feature
• End-of-life signal
• Tamper resistant locking pin
• 9V battery included
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CO250B
9V BATTERY ELECTROCHEMICAL CARBON MONOXIDE ALARM WITH SILENCE
60.96
155
Indoor Air Quality
BRK Electronics Carbon Monoxide and Smoke Alarms
120V AC/DC Carbon Monoxide Alarm
Features:
• Single button test/silence
• 9V alkaline battery backup
• Latching alarm indicator remembers which unit initiated an alarm
• Can silence the low-battery chirp for up to 8 hours or temporarily silence an unwanted nuisance alarm.
• Intelligent Sensing Technology(T M) helps reduce the number of nuisance alarms
• Easy installation and maintenance
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CO5120BN
120V AC/DC CARBON MONOXIDE ALARM
97.54
120V AC/DC Smoke/CO Combo Alarm
Features:
• 9V alkaline battery backup
• Latching alarm indicator remembers which unit initiated an alarm
• Can silence the low-battery chirp for up to 8 hours or temporarily silence an unwanted nuisance alarm.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-SC9120B
120V AC/DC SMOKE/CO COMBO ALARM
121.89
9V Alkaline Battery Powered Smoke/CO Combo Alarm
Features:
• 9V alkaline battery powered
• Latching alarm indicator indicates which unit initiated an alarm or has low battery power
• Can temporarily silence the low-battery chirp or an unwanted nuisance alarm.
• Easy installation and maintenance
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-SCO2B
9V ALKALINE BATTERY POWERED SMOKE/CO COMBO ALARM
89.39
156
Indoor Air Quality
Honeywell C7232 Carbon Dioxide (CO2) Sensor
The Carbon Dioxide (CO2) Sensors and Controllers are stand-alone carbon dioxide (CO2) sensors for use in determining ventilation
necessity with HVAC controllers. The sensor measures the CO2 concentration in the ventilated space. (These models are wall-mount
only.) The sensors are used in ventilation and air conditioning systems to control the amount of fresh outdoor air supplied to maintain
acceptable levels of CO2 in the space.
Features:
• Models available with LCD that provides sensor readings and status information.
• Non-Dispersion-Infrared (NDIR) technology used to measure carbon dioxide gas.
• Gold-plated sensor provides long-term calibration stability.
• C7232 provides voltage or current output based on CO2 levels.
• Models available with SPST relay output.
• Proportional plus Integral (P+I) control algorithm.
• Used for CO2 based ventilation control (Demand Control Ventilation (DCV)).
• Automatic Background Calibration (ABC) algorithm based on long-term evaluation reduces required typical zero-drift check
maintenance.
• Digital input with programmable delay time for occupancy function using a sensor, pushbutton, or switch.
Specifications:
Mounting: Wall
Display: Yes
Carbon Dioxide Range: 0 to 3000 ppm
Analog Output: 0/2 to 10 Vdc or 0/4 to 20mA w/ one relay output
Relay Output: One: Normally Open SPST
Accessories: 32002181-001: Zero Calibration Service
Accuracy: 5% full scale
Timing (response): 2 minutes
SOURCE 1 PART NO.
S1-C7232A1008
S1-C7232A1016
S1-C7232B1014
DIMENSIONS
POWER SUPPLY FREQUENCY (HZ) CONTACT RATING
OPERATING
(VOLT)
TEMPERATURE RANGE
24 VAC (+/– 20%)
50, 60
1 A @ 50 VAC/24 VDC 32ºF TO 122ºF (0ºC TO 50ºC) 5-1/16”H X 3-11/16”W X 2”D (128 MM H X
80 MM W X 25 MM D)
24 VAC (+/– 20%)
50, 60
1 A @ 50 VAC/24 VDC 32ºF TO 122ºF (0ºC TO 50ºC) 5-1/16”H X 3-5/32”W X 2”D (128 MM H X
80 MM W X 25 MM D)
24 VAC (+/– 20%)
50, 60
1 A @ 50 VAC/24 VDC 32ºF TO 122ºF (0ºC TO 50ºC) 5-5/8" H X 3-5/16" W X 3 7/16" D X plus 8"
long sensing tube (142 MM H X 84 MM W
X 87 MM D X plus 203 MM sensing tube)
157
MLP $
618.32
594.68
784.14
CONTROL PANELS
Source 1 Four-Zone Expandable Control Panels
Zone System, Model S1-MZS4
The S1-MZS4 can control various types of HVAC Equipment all from the same panel. The S1-MZS4 features allow the use of single
stage thermostats to control up to three stage heating and two stages cooling and simple heat pump thermostats to control heat
pumps. The S1-MZS4 has various features that make installation and checkout very simple for all of the board’s functionality. T he S1MZS4 panel is made of sturdy ABS plastic and can be mounted to any flat surface. It is recommended that the panel be mounted to a
wall or return plenum and NOT on the furnace or plenum where it will be in contact with the hot temperatures. The panel can be
located in an attic space or in an enclosed cabinet of a rooftop unit, in order for the panel to not be in direct exposure to the elements.
The S1-MZS4’s basic function is zone control. On a call for heating or cooling, the panel will accept the first call from any zone. Upon
accepting this call the S1-MZS4 will open the damper(s) to the zone(s) calling, close the damper(s) to those zones not calling, activate
the needed HVAC controls for heating or cooling, whichever is being called and not accept any calls for the opposite mode. Once all
zone thermostats are satisfied for heating and cooling, the S1-MZS4 will accept Fan calls allowing Continuous Air Circulation( CAC) in
those zones where the thermostat’s Fan Switch is set to ON. These zone dampers will be Open while the dampers to the zones
where the Fan Switch is set to AUTO will be CLOSED. When all zone thermostats are satisfied for both Heating and Cooling, and all
Fan switches are set to AUTO position, the HVAC unit will be off and all zone dampers will return to a normally open position. Once a
zone calls for heating, cooling or fan, the dampers to the calling zones remain open and the dampers to the zones not calling will
close. The S1-MZS4 is factory set for conventional fossil fuel (oil or gas) single and up to three stage heating and two stage cooling.
The panel only needs to be configured when using with an conventional electric furnace or hydro-air system in order to bring the fan
on with a call for heat, or when using with a heat pump equipment and thermostats.
Features:
• Color coded push-in wiring blocks
• LED indicator lights for system operation, Individual zone indicating lights
• Single stage, two stage, and heat pump compatible
• Expandable to any number of Zones, Use s any four-wire thermostat
• Leaving air sensor for capacity protection
• Staging by time or by number of zones calling, Intelligent changeover timing
SOURCE 1 PART NO.
DESCRIPTION
ZONES
STAGES
VOLTAGE
MLP $
S1-MZS4
S1-MZSK
ZONING CONTROL PANEL
ZONING CONTROL PANEL KIT
4
4
2H/2C
2H/2C
24
24
630.50
788.04
Note: S1-M ZSK includes S1-M ZS4 plus S1-ZMS l eaving ai r sensor and 24V transform er
Source 1 Three-Zone Single Stage Control Panels
The S1-MMZ3 Zoning Panel is a 2 and 3 zone, single stage heating and cooling control panel. This electronic panel provides the
simplest zoning functions and works with all standard heating and cooling thermostats.
The S1-MMZ3 panels are designed to use a minimum of wires to make zoning simple and affordable. Each zone uses a standard 4
wire (Y-G-R-W) thermostat. The panels also feature a separate C-common terminal for 24 Volt powered thermostats. All terminal
blocks are color coded for each wire and have push-in connections making wiring even simpler with no need for a small screwdriver,
as with all other zoning panels. The state of the art surface mount technology for all electronic components makes for a highly reliable
control panel.
The zoning operation is very simple and basic. Any zone can call for heating or cooling. Once the first zone calls, the panel will only
accept other calls for the same mode, either heating or cooling. Once all of these calls are satisfied, or a maximum of 20 minutes
elapses, the panel will cut off the HVAC Unit, purge the conditioned air in the duct system and then look for opposite calls. If opposite
calls exist the panel will switch over and supply that mode for the zones calling. When all zones are satisfied for both heating and
cooling, the panel will then accept Fan calls from each thermostat’s Fan switch. This will provide for zoned air circulation. Zones
where the thermostat’s fan switch is ON, will have their dampers open and the fan circulating air continuously. Zones where the Fan
switch is in AUTO, will close their damper until a call is needed for heating or cooling. If all thermostat Fan switches are in AUTO, the
fan will be off and all dampers return to a normally open position awaiting a call.
The S1-MMZ3 panels are compatible with any single stage heating and cooling system and is affordable enough that it can also be
used to zone heating only or cooling only systems as well. It can control any Gas-Oil or Electric Heating Furnace, with or without
Cooling and also zone Hydro-Air Systems using a hot water coil in a cooling air handler.
Panel Specifications:
Features:
• Economy two and three zone control panel Construction: ABS plastic
Number of Zones: 2 and 3 Zones, Single Stage Heating and
• LED indicator lights for system operation
Cooling
• Individual zone indicating lights
Dimensions: 7-5/8” x 7-1/4” x 1-3/8”
• Heating only or cooling only
Voltage: 24 VAC, 50/60 Hz
• Single stage heating and cooling
Temperature Rating: 0°F to 120°F Operating, –20°F to 140°F
Storage
Humidity: 5% to 95% Non-Condensing
Connection: Screwless push-in terminal Blocks
SOURCE 1 PART NO.
DESCRIPTION
ZONES
STAGES
VOLTAGE
MLP $
S1-MMZ3
S1-MMZK
3
3
SINGLE
SINGLE
24
24
244.14
326.43
Note: S1-MM ZK includes S1-MM Z3 pl us S1-ZMS leaving ai r sensor and 24V transformer
158
CONTROL PANELS
Source 1 Two-Zone Add-On Module
A two-zone expansion panel used to add zones onto an S1-MZS4 Zone Control Panel. The S1-MZA2 requires its own separate 24
Volt AC transformer. The panel also includes a modular jack cord which connects the S1-MZA2 with the main S1-MZS4 panel. The
S1- MZA2 is NOT a stand alone zoning panel and is used only as an expansion panel for one or two additional zones when using the
S1-MZS4 as the main zoning panel.When either zone thermostat calls, for either Cooling or Heating, the S1-MZA2 panel will take the
call and look at the S1-MZS4 status. If there are no other calls open the damper to that zone, if not already open, close the dampers
to the zones that are not calling for the same mode and activate the appropriate heating or cooling on the HVAC Unit. If other zones
call for the same mode, the S1-MZS4 panel will allow these calls and open these zone dampers until all zones are satisfied, unless
there are calls from other zones for the opposite mode.When there are opposing calls, the S1-MZS4 panel has a design of intelligent
changeover that can allow those zones to satisfy or eventually switch over to the opposite mode if there are calls for the opposite
mode, based on the number of those zones calling.The S1-MZS4 panel also can control two-stage and heat pump systems using
single stage thermostats. This substantially reduces the overall cost of the zone system by using less expensive conventional single
stage thermostats. The S1-MZS4 has a built-in timer that once a call is made the timer begins and if the demand is not satisfied within
that period of time the second stage will be activated until the call is satisfied. The second stage can also be activated based on the
number of zones calling in place of the timer. The only time a heat pump thermostat is necessary is when it is desired to control the
Emergency Heat from each zone’s thermostat.
Features:
• Two Zone Expansion Panel
• Modular Jacks for Easy Add-On Connection
• Color-Coded Screwless Terminal Blocks
• Individual Zone Indicating Lights
• Indicator LEDs for System Operation
• Expand Systems up to 10 Zones
Panel Specifications
Construction: ABS plastic
Number of Zones: 2 Expansion
Dimensions: 7-5/8”x 7-1/4” x 1-3/8”
Temperature Rating: 0°F to 120°F Operating, –20°F to 140°F Storage
Connection: Screwless push-in terminal Blocks
SOURCE 1 PART NO.
DESCRIPTION
ZONES
STAGES
VOLTAGE
MLP $
S1-MZA2
ADD-ON ZONING MODULE
2
-
-
321.43
Source 1 Three-Zone Multi-Stage Control Panels
The S1-MMH3 Panel can control up to 3 zones and is capable of controlling single stage and two stage heating and cooling, as well
as up to three stage heating, multi-speed and dual fuel heat pumps. This multi-function board uses any 4-wire thermostat. Two stage
and heat pump thermostats are NOT required, however Heat Pump thermostats can be used to remotely control the Emergency Heat.
The S1-MMH3 provides the basic function of zoning by being the central control panel where all zone thermostats, zone damper
motors and HVAC Equipment wire. A separate 24 Volt, 40VA Transformer powers the panel and a separate remote Leaving Air
Sensor is wired to the panel to provide protection and capacity control of the HVAC Equipment. When using dual fuel heat pumps an
outdoor sensor is also wired to control the changeover between heat pump and furnace mode. When any zone thermostat makes a
call, for either Cooling or Heating, the S1-MMH3 panel will take the first call, open the damper to that zone, if not already open, close
the dampers to the zones that are not calling for the same mode and activate the appropriate heating or cooling on the HVAC Unit. If
other zones call for the same mode, the S1- MMH3 panel will allow these calls and open these zone dampers until all zones are
satisfied. When there are opposing calls the S1-MMH3 panel has an exclusive design of intelligent changeover that can allow those
zones to satisfy or eventually switch over to the opposite mode.
The S1-MMH3 panel can control conventional two stage heating, two stage cooling and heat pump systems using single stage
thermostats. This substantially reduces the overall cost of the zone system by using less expensive conventional single stage
thermostats. The S1- MMH3 has a built-in timer that once a call is made the timer begins and if the demand is not satisfied within that
period of time the second and eventually third stage will be activated until the call is satisfied. The panel also has simple Light Emitting
Diodes (LED) indicator to easily monitor the sys-tem status. Two LEDs can be seen through the panel's front cover. These monitor the
basic system operation. By removing the cover, each zone has an indicator light to show when the zone damper is open or the zone is
calling.
Panel Specifications:
Features:
Construction: ABS plastic
• Color-Coded Push-In Wiring Blocks
Number of Zones: 2 and 3 Zones, SingleStage Heating and
• Use s Any Four Wire Thermostat
• Three Stage Heating, Two Stage Cooling & Cooling
Dimensions: 7-5/8" x 7-1/4" x 1-3/8"
Heat umps
• Two and Three Zone Panel
• Leaving Air Sensor for Capacity Protection Temperature Rating: 0°F to 120°F Operating, –20°F to 140°F
Storage
• Intelligent Changeover Timing
• Indicator Lights for System Operation
Connection: Screw less push-in terminal Block
SOURCE 1 PART NO.
DESCRIPTION
ZONES
STAGES
VOLTAGE
MLP $
S1-MMH3
S1-MMHK
3
3
2H/1C
2H/1C
24
24
289.39
371.68
Note: S1-MM HK includes S1-MM H3 plus S1-ZM S leaving ai r sensor and 24V transform e r
159
ZONING ACCESSORIES & DAMPERS
Source 1 Zoning Accessories
Static Pressure Sw itch Model S1-SPS
The Static Pressure Switch is used to sense the supply air duct’s static pressure and control the modulating by-pass damper (Models
S1- ZDM or S1-RDM) in order to maintain the duct system air pressure. When used on a zone control system, the supply air static
pressure increases as various zone dampers close down. The increase in static pressure can become noisy and reduce the volume of
air through the HVAC Unit, if the static overcomes the rating of the blower.
The S1-SPS controls this by sensing the increased static and signaling the modulating by-pass damper to open. As the by-pass
damper opens to relieve the excess static, the air pressure in the duct decreases. The damper responds to the control signal of the
SPS. When the static pressure rises above 0.3”W.C., the S1-SPS will power the motorized by-pass damper open. As the by-pass
damper opens the duct static should decrease below this higher setting of 0.3” and as it does the damper stops. If other zone
dampers open and the static continues to fall below the lower setting of 0.2” W.C., the by-pass damper will close. The two setpoints of
0.2” and 0.3” and the SPST contacts for each, provide the control for the by-pass damper to truly modulate to prevent excessive static
pressure in the system.
By-Pass Control Operation
Above 0.3” W.C. - Damper Opens
Between 0.2”W.C. and 0.3”W.C. – Damper Stops
Below 0.2” W.C. - Damper Closes
The S1-SPS design incorporates two pressure sensitive diaphragms and two single pole single throw snap action electrical switches.
Electrical Ratings:
SPST Snap Acting Electronic Switches
28VA Pilot Duty @ 24VAC
125VA @ 125VAC
SPST Electrical Load
3 A Resistive @ 120VA
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-SPC
S1-SPS
S1-ZMS
STATIC PRESSURE ZONING CONTROL
STATIC PRESSURE ZONING SWITCH
DISCHARGE AIR ZONING SENSOR
397.11
125.00
59.07
Source 1 Modulating Round Zoning Dampers
The S1-RDM can be used for zone control or as the motorized damper for by-pass air when controlled by the Static Pressure Switch,
Model S1-SPS. It is designed to also handle high pressure air conditioning systems up to 4”S.P. The motor actuator delivers up to 18
in/lbs of torque that powers the S1-RDM open and closed. This powerful motor allows the damper to handle higher static pressure s
and can be modulates using the SPS Static Pressure Switch or similar type control.
Features:
• 3-wire, power open and close
• LED damper position indicators
• Neoprene gasket seal
• 24 VAC
Damper Specifications:
Construction: 22 Ga. Galvanized Steel
Linkage: Direct Drive
Motor Voltage: 24 VAC, 50/60 Hz, 6.5 Watts, 7VA
Torque: 35 in-lbs.
Temperature Rating: –4°F to 140°F Operating, –20°F to 150°F Storage
Damper Timing: Nominal 30 Sec. Powered
Connection: Screw Terminals
Duct Pressure: Maximum 4.0” W.C.
SOURCE 1 PART NO.
SIZE (IN.)
MLP $
S1-RDM05
S1-RDM06
S1-RDM07
S1-RDM08
S1-RDM09
S1-RDM10
S1-RDM12
S1-RDM14
5
6
7
8
9
10
12
14
236.86
238.04
239.64
242.71
246.36
249.11
259.57
268.43
S1-RDM16
S1-RDM18
S1-RDM20
16
18
20
280.96
297.11
314.39
Note: S1-RDM dam pers can be used as m odulating powered bypass dam pers when applied with S1-SPS static pressure zoning switch.
160
ZONING ACCESSORIES & DAMPERS
Source 1 Retro-Round Zoning Dampers
A 24 Volt AC, power open, power closed damper. The damper is simply inserted into rigid metal branch ducts. The single blade is
powered open and close to control the flow of air to each outlet. The S1-RRM damper blade has a wide wiper seal to seal against the
inside of the ducts.
The S1-RDM can be used for zone control or as the motorized damper for by-pass air when controlled by the Static Pressure Switch,
Model S1-SPS. It is designed to also handle high pressure air conditioning systems up to 4”S.P.
The simple 3 wire motor has a Red motor release button that allows the damper blade to be manually rotated without harm to the
motor. It also has LED position indicators that illuminate GREEN when Open and RED when Closed.
The motor actuator delivers up to 18 in/lbs of torque that powers the S1-RRM open and closed. This powerful motor allows the
damper to handle higher than normal static pressure, up to 3”W.C.
Multiple dampers can be wired in parallel. Up to 12 dampers per 40VA transformer. When more than 12 dampers are required use a
larger VA transformer. Each motor requires 3VA.
Features:
• Plug-and-play wiring
• Power open and close
• LED damper position indicators
• Rubber gasket seal
• 24 VAC
• Temperature Rating: –4°F to 140°F Operating, –20°F to 150°F Storage
SOURCE 1 PART NO.
SIZE (IN.)
MLP $
S1-RRM04
S1-RRM05
S1-RRM06
S1-RRM07
S1-RRM08
4
5
6
7
8
217.36
217.36
222.04
222.04
223.07
161
ZONING DAMPERS
Source 1 Rectangular Zoning Dampers
Bottom Mount
SOURCE 1 PART NO.
SIZE (IN.)
MLP $
S1-ZDMB0810
S1-ZDMB0812
S1-ZDMB0814
8 x 10
8 x 12
8 x 14
305.64
310.71
331.04
S1-ZDMB0816
S1-ZDMB0818
S1-ZDMB0820
S1-ZDMB0822
S1-ZDMB0824
S1-ZDMB0826
S1-ZDMB0828
S1-ZDMB0830
S1-ZDMB0832
S1-ZDMB0834
S1-ZDMB0836
S1-ZDMB1012
S1-ZDMB1014
S1-ZDMB1016
S1-ZDMB1018
S1-ZDMB1020
S1-ZDMB1022
S1-ZDMB1024
S1-ZDMB1026
8 x 16
8 x 18
8 x 20
8 x 22
8 x 24
8 x 26
8 x 28
8 x 30
8 x 32
8 x 34
8 x 36
10 x 12
10 x 14
10 x 16
10 x 18
10 x 20
10 x 22
10 x 24
10 x 26
336.29
341.36
348.14
337.64
343.61
337.61
342.68
364.46
353.04
358.14
363.21
333.11
353.86
346.04
351.86
372.61
377.43
368.86
374.89
S1-ZDMB1028
S1-ZDMB1030
S1-ZDMB1032
S1-ZDMB1034
S1-ZDMB1036
S1-ZDMB1214
S1-ZDMB1216
S1-ZDMB1218
S1-ZDMB1220
S1-ZDMB1222
S1-ZDMB1224
S1-ZDMB1226
S1-ZDMB1228
S1-ZDMB1230
S1-ZDMB1232
S1-ZDMB1234
S1-ZDMB1236
S1-ZDMB1416
S1-ZDMB1418
S1-ZDMB1420
S1-ZDMB1422
S1-ZDMB1424
S1-ZDMB1426
S1-ZDMB1428
S1-ZDMB1430
S1-ZDMB1432
S1-ZDMB1434
S1-ZDMB1436
S1-ZDMB1618
S1-ZDMB1620
S1-ZDMB1622
S1-ZDMB1624
S1-ZDMB1626
S1-ZDMB1628
S1-ZDMB1630
S1-ZDMB1632
S1-ZDMB1634
S1-ZDMB1636
S1-ZDMB1820
S1-ZDMB1822
S1-ZDMB1824
S1-ZDMB1826
S1-ZDMB1828
S1-ZDMB1830
S1-ZDMB1832
S1-ZDMB1834
S1-ZDMB1836
S1-ZDMB2022
10 x 28
10 x 30
10 x 32
10 x 34
10 x 36
12 x 14
12 x 16
12 x 18
12 x 20
12 x 22
12 x 24
12 x 26
12 x 28
12 x 30
12 x 32
12 x 34
12 x 36
14 x 16
14 x 18
14 x 20
14 x 22
14 x 24
14 x 26
14 x 28
14 x 30
14 x 32
14 x 34
14 x 36
16 x 18
16 x 20
16 x 22
16 x 24
16 x 26
16 x 28
16 x 30
16 x 32
16 x 34
16 x 36
18 x 20
18 x 22
18 x 24
18 x 26
18 x 28
18 x 30
18 x 32
18 x 34
18 x 36
20 x 22
389.39
390.96
418.39
432.21
452.18
354.86
361.89
370.64
392.32
384.00
388.04
395.18
396.54
399.93
437.25
447.00
467.00
368.54
375.57
384.68
390.86
399.57
407.21
414.68
421.71
424.21
431.29
442.89
390.79
403.61
416.39
436.82
457.29
477.79
490.57
500.75
511.00
523.82
416.39
441.93
452.18
477.79
489.68
523.82
534.04
549.39
562.14
464.96
162
ZONING DAMPERS
Bottom Mount
SOURCE 1 PART NO.
SIZE (IN.)
MLP $
S1-ZDMB2024
S1-ZDMB2026
S1-ZDMB2028
S1-ZDMB2030
S1-ZDMB2032
S1-ZDMB2034
S1-ZDMB2036
S1-ZDMB2224
S1-ZDMB2226
S1-ZDMB2228
S1-ZDMB2230
S1-ZDMB2232
S1-ZDMB2234
S1-ZDMB2236
S1-ZDMB2426
S1-ZDMB2428
S1-ZDMB2430
S1-ZDMB2432
S1-ZDMB2434
S1-ZDMB2436
20 x 24
20 x 26
20 x 28
20 x 30
20 x 32
20 x 34
20 x 36
22 x 24
22 x 26
22 x 28
22 x 30
22 x 32
22 x 34
22 x 36
24 x 26
24 x 28
24 x 30
24 x 32
24 x 34
24 x 36
477.79
503.32
508.46
536.61
549.39
564.71
580.07
505.89
526.36
531.50
559.61
580.07
592.89
610.79
549.39
554.54
587.75
603.11
618.46
635.82
Note: S1-ZDM B dampers can be used as m odulating powered bypass
dam pers when applied with S1-SPS static pressure zoning switch.
163
ZONING DAMPERS
Side Mount
SOURCE 1 PART NO.
SIZE (IN.)
MLP $
S1-ZDMS0808
S1-ZDMS1008
S1-ZDMS1010
S1-ZDMS1208
S1-ZDMS1210
S1-ZDMS1212
S1-ZDMS1408
S1-ZDMS1410
S1-ZDMS1412
S1-ZDMS1414
S1-ZDMS1608
S1-ZDMS1610
S1-ZDMS1612
S1-ZDMS1614
S1-ZDMS1616
S1-ZDMS1808
S1-ZDMS1810
S1-ZDMS1812
S1-ZDMS1814
S1-ZDMS1816
S1-ZDMS1818
S1-ZDMS2008
S1-ZDMS2010
S1-ZDMS2012
S1-ZDMS2014
S1-ZDMS2016
S1-ZDMS2018
S1-ZDMS2020
S1-ZDMS2208
S1-ZDMS2210
S1-ZDMS2212
S1-ZDMS2214
S1-ZDMS2216
S1-ZDMS2218
S1-ZDMS2220
S1-ZDMS2222
S1-ZDMS2408
S1-ZDMS2410
S1-ZDMS2412
S1-ZDMS2414
8x8
10 x 8
10 x 10
12 x 8
12 x 10
12 x 12
14 x 8
14 x 10
14 x 12
14 x 14
16 x 8
16 x 10
16 x 12
16 x 14
16 x 16
18 x 8
18 x 10
18 x 12
18 x 14
18 x 16
18 x 18
20 x 8
20 x 10
20 x 12
20 x 14
20 x 16
20 x 18
20 x 20
22 x 8
22 x 10
22 x 12
22 x 14
22 x 16
22 x 18
22 x 20
22 x 22
24 x 8
24 x 10
24 x 12
24 x 14
315.29
320.25
340.18
325.32
347.75
347.68
331.04
353.86
369.46
376.00
336.29
360.64
376.54
383.18
402.86
341.21
366.50
385.25
390.21
405.43
410.54
348.14
372.61
392.32
399.32
418.21
431.04
446.32
352.29
377.43
398.64
405.46
431.04
456.57
479.61
512.82
358.25
383.46
402.64
414.21
S1-ZDMS2416
S1-ZDMS2418
S1-ZDMS2420
S1-ZDMS2422
S1-ZDMS2424
S1-ZDMS2608
S1-ZDMS2610
S1-ZDMS2612
S1-ZDMS2614
S1-ZDMS2616
S1-ZDMS2618
24 x 16
24 x 18
24 x 20
24 x 22
24 x 24
26 x 8
26 x 10
26 x 12
26 x 14
26 x 16
26 x 18
451.46
466.82
492.39
520.50
551.25
352.25
389.54
409.82
421.82
471.93
492.39
164
ZONING DAMPERS
Side Mount
SOURCE 1 PART NO.
SIZE (IN.)
MLP $
S1-ZDMS2620
S1-ZDMS2622
S1-ZDMS2624
S1-ZDMS2808
S1-ZDMS2810
S1-ZDMS2812
S1-ZDMS2814
S1-ZDMS2816
S1-ZDMS2818
S1-ZDMS2820
S1-ZDMS2822
S1-ZDMS2824
S1-ZDMS3008
S1-ZDMS3010
S1-ZDMS3012
S1-ZDMS3014
S1-ZDMS3016
S1-ZDMS3018
S1-ZDMS3020
S1-ZDMS3022
S1-ZDMS3024
S1-ZDMS3208
S1-ZDMS3210
S1-ZDMS3212
S1-ZDMS3214
S1-ZDMS3216
S1-ZDMS3218
S1-ZDMS3220
S1-ZDMS3222
S1-ZDMS3224
S1-ZDMS3408
S1-ZDMS3410
S1-ZDMS3412
S1-ZDMS3414
S1-ZDMS3416
S1-ZDMS3418
S1-ZDMS3420
S1-ZDMS3422
S1-ZDMS3424
S1-ZDMS3608
S1-ZDMS3610
S1-ZDMS3612
S1-ZDMS3614
S1-ZDMS3616
S1-ZDMS3618
S1-ZDMS3620
S1-ZDMS3622
S1-ZDMS3624
26 x 20
26 x 22
26 x 24
28 x 8
28 x 10
28 x 12
28 x 14
28 x 16
28 x 18
28 x 20
28 x 22
28 x 24
30 x 8
30 x 10
30 x 12
30 x 14
30 x 16
30 x 18
30 x 20
30 x 22
30 x 24
32 x 8
32 x 10
32 x 12
32 x 14
32 x 16
32 x 18
32 x 20
32 x 22
32 x 24
34 x 8
34 x 10
34 x 12
34 x 14
34 x 16
34 x 18
34 x 20
34 x 22
34 x 24
36 x 8
36 x 10
36 x 12
36 x 14
36 x 16
36 x 18
36 x 20
36 x 22
36 x 24
517.96
541.00
564.04
357.29
404.00
411.18
429.29
492.39
504.32
523.07
546.11
569.14
379.07
405.57
414.57
436.36
505.21
538.43
551.25
574.21
602.39
367.64
433.00
451.86
438.86
515.39
548.68
564.04
594.71
617.75
372.75
446.86
461.64
445.89
525.64
564.04
579.36
607.5
633.11
377.82
466.82
481.64
457.5
538.43
576.79
594.71
625.43
650.46
SOURCE 1 PART NO.
DIAMETER SIZE (IN.)
MLP $
S1-SPRD08
S1-SPRD09
S1-SPRD10
S1-SPRD12
S1-SPRD14
S1-SPRD16
S1-SPRD18
S1-SPRD20
8
9
10
12
14
16
18
20
78.39
83.54
87.07
100.43
110.64
122.32
139.89
179.21
Note: S1-ZDM S dampers can be used as m odulating powered bypass
dam pers when applied with S1-SPS static pressure zoning switch.
BY-PASS DAMPERS
Source 1 Barometric By-Pass Dampers
Source 1 Round Barometric Bypass Dampers
165
BY-PASS DAMPERS
Source 1 Barometric By-Pass Dampers
Source 1 Rectangular Barometric Bypass Dampers
SOURCE 1 PART NO.
SIZE (IN.)
MLP $
S1-SPRD1208
S1-SPRD1210
S1-SPRD1212
S1-SPRD2008
S1-SPRD2010
S1-SPRD2012
12 x 8
12 x 10
12 x 12
20 x 8
20 x 10
20 x 12
97.96
105.46
107.32
102.82
110.75
111.89
ECONOMIZER CONTROLS & ECONOMIZER LOGIC MODULES
Honeywell C7660 Selectable Temperature Sensor
Honeywell C7660 Selectable Temperature Sensor C7660 Selectable Temperature Sensor is used with the W7459, W7215, W7212,
W7213 and W7214 Economizer Controls. The economizer controls are mounted on an M7415/M7215 Actuator. They permit the use
of outdoor air as the first stage of cooling in heating, ventilating and air conditioning (HVAC) systems.
The C7660 Selectable Temperature Sensor is only to be used with single temperature change over with the sensor located in the
outdoor air.
Features:
• Senses temperature of outdoor air and provides a signal to economizer control with OK or not OK to economize.
• Selectable dip switch provides 8 change over temperature options.
• When temperature of outdoor air is below change over temperature, the outdoor air damper is opened to reduce the
cooling load in the building.
• Provides 4 OR 20 mA output signal to economizer control; At 4 mA not OK to economize, 20 mA OK to economize.
• Highly accurate microprocessor control.
• Sensor is enclosed in a rugged, corrosion-resistant plastic case.
• Replaces C7650 temperature sensors and the control function of temperature change over in the economizer control.
• Easy to set change real time temperature settings. The installer can change the temperature set point without cutting
power to the system.
Specifications:
Model: C7660 Selectable Temperature Sensor , Case: Duct mount
Temperature Sensing Element: Thermistor
Output Signal: 4mA not OK to economize, 20 mA OK to economize
Operating Ambient Temperature Range: -40° to 149° F (-40° to 65° C).
Shipping Temperature Range: -40° to 149° F (-40° to 65° C).
Supply Voltage: Power to sensor is supplied through economizer or if not used with an economizer, logic power
input is 21.6 vdc ± 1.5 vdc.
Electrical Connections: Two 1/4 in. (6.4 mm) quick connect terminals.
Approv al: Underwriters Laboratories Inc. Flammability Rating UL94-5V
Dimensions: 3-5/32" H x 3-7/8" W x 1" D
Hysteresis: Hysteresis +/- 1F; Economizer Cut-in 1F below setpoint, Cut-out 1F above setpoint ,
Accuracy: ± 1° F
SOURCE 1 PART NO.
APPLICATION TYPE
MOUNTING
USED WITH
MLP $
S1-C7660A1000
DUCT OUTSIDE (SUPPLY)
OR RETURN
IN ANY LOCATION WHERE IT IS EXPOSED
TO FREELY CIRCULATING AIR
W7210, W7212, W7213, W7214,
W7216, W7459, W7460
51.50
Honeywell Communicating discharge air temperature sensor
Duct-m ounted tem perature probe used to provide capacity control of heating and cooling equipment. Used with Honeywell Network
Zoning System and single unit zone applications.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-C7835A1009
Communicating discharge air temperature sensor
146.89
166
ECONOMIZER CONTROLS & ECONOMIZER LOGIC MODULES
Honeywell W7210D1005 Series 72 Economizer Logic Module
W7210A,D Solid State Economizer™ Logic Modules are used with solid state C7400 Enthalpy Sensors or C7660 Dry Bulb
Temperature Sensors and Honeywell Series 72 actuators to proportion outdoor and return air dampers for economizer control in
commercial HVAC equipment
Features:
• Operates from the commercial thermostat to provide a totally integrated control system.
• Includes enthalpy or dry bulb changeover control, minimum damper position potentiometer and compressor staging relay functions.
• Optional differential enthalpy control provides greater economizer savings than single enthalpy control by selecting the most
economical air for cooling.
• Differential enthalpy control uses two sensor inputs, one in return air and one in outdoor air then economizer control selects the air
with the lower enthalpy.
• Enthalpy setpoint (A-D) W7210 Solid State Economizer Logic Module controls the combination of air temperature and humidity
suitable for free cooling.
• LED indicates when free cooling is available.
• Mount on the sheet metal duct.
• Mounting screws included.
Specifications:
Use With: Honeywell Series 72 actuators
Comments: Economizer Logic Module operates Series 72 actuators. Optional remote minimum position potentiometer. High enthalpy
limit.
Underw riters Laboratories Inc.: Flammability Rating UL94V-5V
SOURCE 1 PART NO.
S1-W7210D1005
USE WITH SENSOR
C7660, C7046, C7150, C7400
OUTPUT
CONTACT RATING
TWO SPDT, ONE 2-10VDC
1.5 A RUN @ 24 VAC, 3.5 A
INRUSH @ 24 VAC
VOLTAGE FREQUENCY
(VAC)
(HZ)
24
50/60
MLP $
413.54
DAMPER ACTUATORS
Honeywell Foot Mounted Actuator
Spring return motors for two-position back draft, outdoor air changeover, zone, or minimum position damper control.
Features:
• Operate outdoor air dampers for combustion or makeup air in residential and light industrial applications.
• Operate changeover dampers for heating and cooling systems.
• Operate minimum position dampers for ventilation and similar applications.
• Include internal spdt switch for controlling auxiliary equipment, additional motors, or to provide a burner interlock switch.
• Spring returns motor to start position on power failure.
• Drive shafts located on both sides of motor.
• Adjustable auxiliary switch for cascading motors or operating auxiliary equipment.
• Thermal breaker for overload protection during lifting stroke or if motor stalls.
Specifications:
Fail Safe Mode: Spring Return
Torque Rating (lb-in.): 20 lb-in.
Torque Rating (Nm): 2.3 Nm
Timing Opening, Nominal (sec) Open: 30 sec
Run Time (Maximum (sec): 40 sec
Angle of Rotation (Stroke Min (deg): 75
Angle of Rotation (Stroke Max (deg): 75
Motor shafts: 2
Shaft Shape: Hexagonal
Electrical Connections: Screw terminals
Internal Auxiliary Switch: 1
External Auxiliary Sw itches Av ailable: Yes
Nominal Current Draw Opening (amps): 1.85 A
Nominal Current Draw Holding (amps): 0.6 A
Nominal Power Opening (watts): 40 W
Nominal Power Holding (w atts): 8.5 W
Weight (lb): 4 lbs, 10 oz
Weight (kg): 2.1 kg
Humidity Ratings (%RH): 5 to 95% RH
Approv als: Underwriters Laboratories Inc Listed File: E4436, Guide: XAPX
SOURCE 1 PART NO.
S1-M836A1042
VOLTAGE SPRING RETURN
TIMING
24 VAC
25 SEC
CONTROL SIGNAL TORQUE/RATING, FREQUENCY MOUNTING TYPE OPERATING TEMPERATURE
BREAKAWAY
RANGE
TWO POSITION,
30 LB-IN.
60 HZ
FOOT MOUNTED 32°F TO 125°F (0°C TO 52°C)
SPST
167
MLP $
614.29
DAMPER ACTUATORS
Honeywell ML6161 Direct-Coupled, Non-Spring Return Damper Actuators
Used to control dampers in applications such as variable air volume (VAV) terminal units, and for mounting on ball valves
Features:
• Superior A/C synchronous submotor for consistent timing and actuator longevity.
• Eliminate need for limit switches or mechanical stops by providing magnetic coupling.
• All models include manual declutch lever, and bag assembly with two minimum position setscrews.
• Mount directly on 3/8” or 1/2” square or round damper shaft.
• Selectable 45, 60, and 90 stroke in either clockwise or counterclockwise direction.
Specifications:
Description: Non-Spring Return Direct Coupled Actuator
Type of Control: Electric
Feedback: With accessory only
Electrical Connections: Screw terminals
Stroke Max (deg, in): Adjustable w/accessory (30, 60, or 90 deg)
External Aux. Sw itches Available: Yes
Power Consumption: 2.04 VA
Mounting: 3/8” to 1/2” square or round shaft (9 mm to 13 mm)
Approv als, Underw riters Laboratories Inc.: File E4436, Guide: XAPX2
Includes: 4074ENJ Bag Assembly
SOURCE 1 PART NO.
VOLTAGE
S1-ML6161A2009
S1-ML6161A2017
24 VAC
24 VAC
SPRING
RETURN
NO
NO
CONTROL SIGNAL
TORQUE/FORCE
SPDT, FLOATING
SPDT, FLOATING
35 LB.-IN. (4 NM)
35 LB.-IN. (4 NM)
TIMING FREQUENCY MOUNTING TYPE
AMBIENT TEMPERATURE
MAX
RANGE
90 SEC.
50/60 HZ
DIRECT COUPLED 20ºF TO 125ºF (–18ºC TO 50ºC)
7 MIN.
50/60 HZ
DIRECT COUPLED 21ºF TO 125ºF (–18ºC TO 50ºC)
MLP $
167.50
163.07
PROPORTIONAL MOTORS
Honeywell M9164 Modutrol IV Motors
Reversing, proportional motors used to operate dampers and valves.
Features:
• Replace M934 Motors.
• Electronic drive circuit.
• Can drive up to six Modutrol motors using 4074BYK Resistor Bag Assembly or 221508A Resistor Board Kit.
• Interface modules available for series 70 (electronic) control.
• Internal actuator motor and circuitry operate from 24 VAC. Line voltage models shipped with internal transformers. Separate
transformer may be required for 24V models for proper system operation.
• Double-ended, 3/8” (10 mm) square crankshaft.
Specifications:
Control Signal: Proportional Control, 135 ohm
Fixed Stroke: No
Stroke: 90 deg Minimum, 160 deg, in Maximum
Power Consumption: 15 VA
Electrical Connections: Quick connect terminals
Motor Shafts: 2
Shaft Dimensions: 9.5 mm
Shaft Shape: Square
Manual Operation: None
Weight: 7 Lbs.
Dimensions: 6.45”H x 5.5”W x 7.3”D (164 mm H x 140 mm W x 185 mm D)
Includes: 220738A Adapter Bracket
Approv als: Underwriters Laboratories Inc. File E4436, Guide XAPX; Canadian Standards Association File LR1620, Guide 400-E; CE
Standard EN55011 (Emission) EN50082-2 (Immunity) 73/23/EEC (LVD)
TIMING
SOURCE 1 PART NO.
VOLTAGE
S1-M9164D1009
24 VAC
SPRING
RETURN
NO
TORQUE/FORCE
MIN
MAX
35 LB.-IN. (4 NM)
30 SEC.
60
168
FREQUENCY MOUNTING AMBIENT TEMPERATURE
TYPE
RANGE
FOOT
–40ºF TO +150ºF
50/60 HZ
MOUNTED
(–40ºC TO +66ºC)
MLP $
714.29
PROPORTIONAL MOTORS
Honeywell M9185 Modutrol IV Motors
Reversing, proportional, spring-return motors used to operate dampers and valves when used in a series 90 control circuit.
Features:
• M9185 replaces M945A,D,F and M955 motors.
• Can be adapted to series 70 control with interface modules.
• Contain integral helical springs to return motor shafts to normal position (full closed for M9175 and M9185, full open for M9186) on
power interruption.
• Oil-immersed motor and gear train provide reliable performance and long life.
• Provide NEMA 3 weather protection with wiring box, when mounted upright.
• Up to six Modutrol motors can be driven by one series 90 controller using 4074BYK Resistor Bag Assembly or 221508A Resistor
Board.
• Internal actuator motor and circuitry operate from 24 VAC. Line voltage model shipped with internal transformer.
• Double-ended, 3/8” (10 mm) square crankshaft.
Specifications:
Control Signal: Proportional Control, 135 ohm
Feedback: No
Fixed Stroke: No
Stroke: 90 deg Minimum, 160 deg, in Maximum
Power Consumption: 24 VA
Electrical Connections: Quick connect terminals
Motor Shafts: 2
Shaft Dimensions: 9.5 mm
Shaft Shape: Square
Manual Operation: None
Weight: 9.562 Lbs.
Dimensions: 6.45”H x 5.5”W x 8.76”D (164 mm H x 140 mm W x 223 mm D)
Includes: 220738A Adapter Bracket
Approv als: Underwriters Laboratories Inc. File E4436, Guide XAPX; Canadian Standards Association File LR1620,
Guide 400-E; CE Standard EN55011 (Emission) EN50082-2 (Immunity) 73/23/EEC (LVD)
TIMING
SOURCE 1 PART NO.
VOLTAGE
SPRING
RETURN
S1-M9185D1004
24 VAC
YES
TORQUE/FORCE
MIN
MAX
60 LB.-IN. (6.8 NM) 30 SEC.
60
FREQUENCY MOUNTING
TYPE
50/60 HZ
AMBIENT
TEMPERATURE
RANGE
–40ºF TO +150ºF
(–40ºC TO +66ºC)
FOOT
MOUNTED
MLP $
1237.43
Honeywell Signal Interface Module
Interface module for Modutrol IV motor. For use with Series 91 Mod IV Motors.
Specifications:
Control Signal: Provides adjustable zero and span, voltage or current control (includes 2-10 Vdc or 4-20 mA). Adapts M91xx to
function as M72xx model.
Electrical Connections (in): T erminal board
Mounting Type: Mounts to quick-connects inside Mod Motor
Dimensions: Fits inside wiring junction box of Modutrol IV Motor
SOURCE 1 PART NO.
FREQUENCY
POWER CONSUMPTION
WEIGHT
AMBIENT TEMPERATURE RANGE
MLP $
S1-Q7230A1005
50/60 HZ
2 VA
0.3 LB.
–40ºF TO +150ºF (–40ºC TO +66ºC)
210.46
VENTS, VENT HOODS & DUCTWORK
Louvered Dryer Vent Hood
Deflecto’s SUpurr-Vent louvered vent hoods are available with aluminum pipe and collar or hood only. Ideal for dryer and bathroom
fan exhausts.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-650-014
S1-650-015
4” HOOD ONLY – WHITE
4” HOOD ONLY W/BIRD GUARD – WHITE
48
24
5.32
5.32
S1-650-016
S1-650-017
S1-650-036
4” HOOD, PIPE AND COLLAR – WHITE (ASSEMBLED)
4” HOOD, PIPE AND COLLAR – WHITE (UNASSEMBLED)
3” HOOD, PIPE AND COLLAR – WHITE (ASSEMBLED)
6
6
6
7.89
7.61
8.11
*Sold by Standard Pack / M LP per each
169
Metallic Duct—2 Ply
2 ply metallic duct — aluminum outside, polyester inside. Ideal for bath fan ducting and all purpose venting.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-FM0450
4” x 50’ METALLIC DUCT
80.96
Periscope Connection Kit
For tight space duct venting. Contains one male snap-lock fitting and one draw-band with clamp. Adjustable 17” to 28”.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-650-020
4” PERISCOPE KIT
9
45.86
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-650-012
S1-650-013
S1-650-023
S1-650-031
4” WHITE HOOD – ASSEMBLED
4” WHITE HOOD – UNASSEMBLED
4” BROWN HOOD – ASSEMBLED
3” WHITE HOOD – ASSEMBLED
6
6
6
6
8.18
7.21
8.11
9.25
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-650-011
S1-650-021
S1-650-074
4” x 8’ FLEXIBLE ALUMINUM DUCT
9
16
4
14.36
12.82
25.50
Plastic Wide Mouth Dryer Vent Hood
Hood, aluminum pipe and collar.
Semi-Rigid Aluminum Duct
8’ length compressed to 28”.
170
SUpurr-FLEX 5 Ply Duct
Pure aluminum 5 ply multi-layered flexible metallic duct. U.L. 181 Listed. Will “contain” a fire up to 265°F.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-FUL0325
S1-FUL0425
S1-FUL0625
3” x 25’ SUPURR-FLEX
51.54
62.04
87.89
171
Duct Connectors
NEOPRENE RESIDENTIAL DUCT CONNECTOR
NEOPRENE is the choice of specifying engineers. It is the industry standard, retaining its flexibility and aging
characteristics over a long period of time. NEOPRENE offers high resistance to a broad range of chemicals,
acids and alkalis.
Features:
• The Industry Standard for Air-Handling Systems
• Airtight, Waterproof, Resistant to Mildew
• Resistant to Many Acids, Oils, Alkalines, Toxic Fumes
• Used in High-Velocity, High-Pressure Systems
• Fabric is Tested in Accordance with ANSI/UL-214 for Flame Propagation of Fabrics and Films
SOURCE 1 PART NO.
DESCRIPTION
CODE
MLP $
S1-307892
CONNECTOR RESIDENTIAL NEOPRENEOPEN
BLACK 2-3-2 28G, 100' ROLL
RCPN-O8-100
426.43
VINYL-FLEX COMMERCIAL DUCT CONNECTOR
VINYL-FLEX can be used on both supply and return air ducts in most HVAC applications where an economical
flexible connection is required and can be used in damp locations, resisting bacterial attack. VINYL-FLEX is a
replacement for canvas, which is no longer considered acceptable.
Features:
• Low Cost
• Leak Proof
• Wide Temperature Range
• Good Abrasion Resistance
• Resistant to Moisture and Mildew
• Used in Heating and Cooling Applications
• Available Black or Yellow
• Great Strength and Tear Resistance
• Flame Resistant - Self Extinguishing ARL Listed and Tested in Accordance with ANSI/UL-214 for Flame
Propagation of Fabrics and Films
SOURCE 1 PART NO.
DESCRIPTION
CODE
MLP $
S1-307829
CONNECTOR TDC/TDF VINYLFLEX CLOSE BLACK
4-3-4 24G, 100' ROLL
CPDL-BV
453.93
VINYL-FLEX RESIDENTIAL DUCT CONNECTOR
VINYL-FLEX is a polyvinyl chloride-coated polyester woven fabric with tremendous tear resistance.
Features:
• Low Cost
• Leak Proof
• Wide Temperature Range
• Good Abrasion Resistance
• Resistant to Moisture and Mildew
• Used in Heating and Cooling Applications
• Available Black or Yellow
• Great Strength and Tear Resistance
• Flame Resistant - Self Extinguishing ARL Listed and Tested in Accordance with ANSI/UL-214 for Flame
Propagation of Fabrics and Films
SOURCE 1 PART NO.
DESCRIPTION
CODE
MLP $
S1-307899
CONNECTOR RESIDENTIAL VINYLFLEX CLOSE
BLACK 2-3-2 28G, 100' ROLL
RCPV-B8-100
240.14
TM
GRIP-ON
INSULATION FASTENERS
ST IK-ONS are 14-gauge steel insulation pins that are permanently staked through 2” x 2" galvanized steel base plates. A pressure
sensitive adhesive backing provides a permanent bond between the STIK-ONS and ductwork. Clips included. STIK-ONS can be used
to hold all low- and medium-density insulation and insulation board where the temperature will not exceed180°F (82°C.).
Product Technical Data:
• Temperature Range: -30°F (-35°C) - 180°F (82°C)
• Application Temperature: above 40°F (4°C)
• Holding Power: 3 lbs per unit
• Approximate Shelf Life: 2 years @ 70°F (21°C)
SOURCE 1 PART NO.
DESCRIPTION
CODE
MLP $
S1-308166
S1-308167
S1-308168
STIK-ONS, 3/4", 1000 PCS
STIK-ONS, 1 1/4", 1000 PCS
STIK-ONS, 1 3/4", 1000 PCS
SKM-75
SKM-125
SKM-175
292.25
314.93
307.54
172
TM
STIK-ON
INSULATION FASTENERS
GRIP-ON Pins are m ade with nail tips that have a double claw that grabs more m etal. T he hardened tip penetrates sheet m etal, yet is
soft enough to bend at the right moment of impact with an underlying harder surface. T he points will not shatter.
SOURCE 1 PART NO.
DESCRIPTION
CODE
MLP $
S1-308229
S1-308233
GRIP-ONS 1/2", 5000 PCS
GRIP-ONS, 1",1 LD, 5000 PCS
GOB-50
GOB-100LD
725.39
638.93
WELD-ONTM INSULATION FASTENERS, CUP HEAD
WELD-ONS are manufactured with consistently sharp points to ensure positive contact with the sheet metal to which they are to be
welded. Produced from special carbon alloy steel, the point of the welding pin is hardened in a unique cold form process. T his
hardens the points, giving them a steel temper, which, unlike other welding pins, will not blunt or flatten when applied. The sharper
point of contact results in a better weld and creates fewer sparks that ignite adhesives or burn substrates. WELD-ONS are easily
applied using any conventional portable or automatic resistance welding unit. Cup-style washer is designed to sufficiently depress the
insulation surface without tearing it.
SOURCE 1 PART NO.
DESCRIPTION
CODE
MLP $
S1-308122
WELD-ONS, CUP HEAD,1-1/8", 4000 PCS
DWB-118
404.00
WELD-ONTM INSULATION FASTENERS, FLAT HEAD
WELD-ONS are manufactured with consistently sharp points to ensure positive contact with the sheet metal to which they are to be
welded. Produced from special carbon alloy steel, the point of the welding pin is hardened in a unique cold form process. T his
hardens the points, giving them a steel temper, which, unlike other welding pins, will not blunt or flatten when applied. The sharper
point of contact results in a better weld and creates fewer sparks that ignite adhesives or burn substrates.
SOURCE 1 PART NO.
DESCRIPTION
CODE
MLP $
S1-308134
S1-308135
S1-308136
S1-308141
S1-308142
S1-308143
WELD-ONS, FLAT HEAD, 1/2", 1000 PCS
WELD-ONS, FLAT HEAD, 1", 1000 PCS
WELD-ONS, FLAT HEAD, 1", 5000 PCS
FWT-50
FWT-75
FWT-100
FWB-50
FWB-75
FWB-100
79.50
85.07
95.21
377.54
406.11
458.46
Aluminum Dryer Vent Hoods, Kits, and Fittings
Aluminum vent hood with flange plate. Kits include flexible vinyl tubing and two clamps.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-650-001
S1-650-002
4” ALUMINUM HOOD
3” ALUMINUM HOOD
24
24
8.25
8.25
S1-650-003
S1-650-004
S1-650-018
S1-650-038
4” HOOD / 8’ TUBING
4” HOOD / 5’ TUBING
4” 90º ELBOW
4” ALUMINUM WIDE MOUTH
24
24
24
12
19.36
16.04
13.18
10.43
Dryer Hose Clamps
Available for 3” or 4” dryer vent hose. Steel screw design or convenient spring action design.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-650-008
S1-650-010
STEEL SCREW CLAMP FOR 4” HOSE
SPRING CLAMP FOR 4” HOSE
25
100
2.54
1.18
173
Dryer Vent Hose
High quality flexible white vinyl tubing. Available in 3” or 4” diameters. One 50’ roll per box.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-650-005
S1-650-006
DRYER VENT HOSE – 3” x 50’
DRYER VENT HOSE – 4” x 50’
37.79
37.79
BOOSTER FANS & ROOF FLASHINGS
Booster Fans
For hard to heat or cool rooms. Easily installs in branch duct (round, square, or rectangular) which supplies air to the problem room.
Electrical hookup can be to a wall switch, auxiliary switch, thermostat or directly to the blower making it possible to use all the time or
only at certain times. Each booster fan individually boxed.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-625-AF10
S1-625-AF12
S1-625-AF14
S1-625-AF6
S1-625-AF8
BOOSTER FAN – 650 CFM – 10”
2
1
1
4
4
117.64
156.86
196.07
54.93
69.61
No-Caulk Roof Flashings
Exclusive one-piece construction insures a positive leakproof installation every time. Specially formulated elastomeric collar allows the
vent stack plenty of room for expansion and contraction. Easy to install, the no-caulk flashing slips over the vent stack and
automatically adjusts to pipe size and roof angle, and remains perfectly flat on the roof. Not designed for hot-mopped or built up roofs.
All flexible flashings are manufactured from a specially formulated elastomer material which is extremely flexible and durable. They
permit the vent stack to expand and contract freely without disrupting the seal between the pipe and flashing collar.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-11853
S1-11866
S1-11879
S1-5-11830
2" NO-CAULK GALVANIZED
20.36
22.15
19.68
11.89
Masterflash
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-14052
S1-14053
S1-14057
1/2" – 4"
3" – 6”
7" – 13”
34.68
54.57
170.11
DESCRIPTION
3” – 6”
7” – 13”
174
DIMENSIONS (IN INCHES)
A
B
C
2.5
3-6
10 X 10
6
7-13
17 X 17
FLUE CAPS & LOUVERS
Versa Cap® Flue and Hot Stack Caps
Non-clogging positive draft design, recommended for flue or hot stack installation. Clamp fitting adjustable for all standard sizes.
Aluminum model. U.L. Listed.
SOURCE 1 PART NO.
PIPE O.D.
DOUBLE WALL
SINGLE WALL
J-M TRANS. SITE
HEIGHT/OVERALL DIAMETER
STD. PACK
MLP $
S1-6-1200
S1-6-3050
S1-6-5070
S1-6-7090
S1-6-9011
11-7/8”–14-1/2”
2-7/8”–5”
4-7/8”–7”
6-7/8”–9”
8-7/8”–11”
12
3 AND 4
5 AND 6
7 AND 8
9 AND 10
12 AND 14
3 AND 4
5 AND 6
7 AND 8
9 AND 10
12
3 AND 4
5 AND 6
7 AND 8
9 AND 10
8-11/16” x 17-9/16”
4-1/2” x 6-5/8”
4-3/4” x 9-1/2”
5-7/8” x 11-5/8”
6-1/2” x 12-3/4”
2
12
12
12
6
220.79
43.32
57.64
82.57
116.04
E cap Flue Cap
The DiversiTech EC-1 Flue Cap is an affordable way to protect today's high efficiency furnaces & PVC vented equipment from dirt,
moisture and other debris.
Features:
•
•
•
•
•
•
Protection for high efficiency furnaces
Universal flue cap fits 1.5”, 2” and 3” PVC pipe
Reduces draft inducer motor rust
Helps to eliminate pressure switch service calls
Resistant to UV radiation and oxidative degradation
CSA approved for use in 90% AFUE heating applications
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-DT-EC-1
E cap Flue Cap
25.46
Egg Crate Louvers - Air Return Diffusers
White polystyrene 1/2” open cell grid.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-650-100
S1-650-200
S1-650-300
EGG CRATE LOUVERS – 2’ x 4’ x 1/2”
10
15
20
34.07
22.11
20.43
Slant Back Roof Louver
Easy to install. Aluminum construction. Fits all roof types.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-6-NSB50A
ALUMINUM SLANT BACK ROOF LOUVER
6
38.86
175
—NOTES—
176
Source 1 Motors
HIGH-AMBIENT CONDENSER FAN MOTORS
Features:
• NEW High Temp 70°C ambient design
• Installs with all standard 48 frame mounting brackets
• Standard shaft length, diameter, and flats
• Drain holes with plugs in both end plates
• Automatic thermal overload protector
• Use s standard 370V capacitor
• Standard motor casing size
• Low power consumption
• Electrically reversible
• Continuous duty air over
• Class B insulation
• Quiet operation
• Extended studs
• 30” leads
• 60Hz
RATED/
SOURCE 1 PART NO.
HP
VOLTS
FLA
LRA
SPEED
BEARINGS
370V CAPACITOR
DIM. A
WT. (LBS.)
MLP $
S1-FHM3728HT
S1-FHM3729HT
S1-FHM3730HT
S1-FHM3204HT
S1-FHM3205HT
S1-FHM3736HT
S1-FHM3737HT
S1-FHM3738HT
S1-FHM3739HT
S1-FHM3465HT
S1-FHM3469HT
1/4
1/3
1/2
1/4
1/3
1/4
1/3
1/2
3/4
1/3-1/6
1/3-1/6
208/230
208/230
208/230
208/230
208/230
460
460
460
460
208/230
208/230
2.2
2.8
4.2
1.5
2.2
0.8
1.5
2.3
2.6
2.8
1.9
3.80
5.40
7.80
2.40
3.30
1.65
2.85
4.30
5.30
1075/1
1075/1
1075/1
825/1
825/1
1075/1
1075/1
1075/1
1075/1
1075/2
825/2
SLEEVE*
SLEEVE*
SLEEVE*
BALL
BALL
BALL
BALL
BALL
BALL
BALL
BALL
S1-CAP37050F, S1-CAP37050R
S1-CAP37075F, S1-CAP37075R
S1-CAP37100F, S1-CAP37100R
S1-CAP37075F, S1-CAP37075R
S1-CAP37100F, S1-CAP37100R
S1-CAP37075F, S1-CAP37075R
S1-CAP37075F, S1-CAP37075R
S1-CAP37100F, S1-CAP37100R
S1-CAP37100F, S1-CAP37100R
S1-CAP37050F, S1-CAP37075F
S1-CAP37075F, S1-CAP37100F
4.25
4.52
5.29
4.25
4.53
4.25
5.32
5.75
6.1
5.0
5.25
12
12
16.28
12
12
12.1
12.1
16.28
22
13.6
14.5
153.39
174.82
201.61
183.75
208.75
183.36
213.86
246.82
281.46
192.43
192.39
Cross Reference
SOURCE 1 PAR T NO.
S1-FHM372 8HT
S1-FHM372 9HT
S1-FHM373 0HT
S1-FHM320 4HT
S1-FHM320 5HT
S1-FHM373 6HT
S1-FHM373 7HT
S1-FHM373 8HT
S1-FHM373 9HT
S1-FHM346 5HT
S1-FHM346 9HT
AO S MITH*
FSE1026S
FSE1036S
FSE1056S
FSE1028S
FSE1038S
FEH1026S
FEH1036S
FEH1056S
FEH1076
FE6000
FE6001
AO S MITH HE AT MAS TER
FSE1026SF
FSE1036SF
FSE1056SF
FE1028SF
FE1038SF
FEH1026SF
FEH1036SF
FEH1056SF
FEH1076SF
ORM545 8BF
ORM548 8BF
* Competitors’ motors are only rated for 60°C ambient.
* All produced after December 2012 will have ball bearings.
177
GE*
3728
3729
3730
3204
3205
3736
3737
3738
3739
3465
3469
FASCO*
D909
D908
D907
D743
D796
D980
D982
D802
D1914
D2827
D2826
EMERSON*
1860
1861
1862
1874
1875
3736
3737
3738
3742
5462
5464
Source 1 Motors
SINGLE HORSEPOWER CONDENSER FAN MOTORS
Features:
• Drain holes with plugs in both end plates
• Use s standard 370V capacitors
• 60°C ambient design
• Electrical reversing plug
• Continuous air over
•
•
•
•
•
•
•
Class B insulation
Quiet operation
Extended mounting bolts
30” leads
Rotation reversible
Single phase
2-year warranty!
Specifications:
Voltage: 208/230 VAC; 60 Hz
RATED
SOURCE 1 PART NO.
HP
RPM SPEED AMPS
S1-FHM3204
S1-FHM3205
S1-FHM3727
S1-FHM3728
S1-FHM3729
S1-FHM3730
S1-FHM3731
1/4
1/3
1/6
1/4
1/3
1/2
3/4
825
825
1075
1075
1075
1075
1075
1
1
1
1
1
1
1
2.4
3.3
1.2
1.9
3.2
3.8
4.6
LRA
FLA
2.2
3.8
6.4
8.1
8.5
1.5
2.2
1.5
2.4
4.0
5.3
5.9
BEARING
TYPE
BALL
BALL
SLEEVE*
SLEEVE*
SLEEVE*
SLEEVE*
SLEEVE*
RUN CAPACITOR
REPLACES
MLP $
S1-CAP37075F, S1-CAP37075R
S1-CAP37100F, S1-CAP37100R
S1-CAP37050F, S1-CAP37050R
S1-CAP37050F, S1-CAP37050R
S1-CAP37075F, S1-CAP37075R
S1-CAP37100F, S1-CAP37100R
S1-CAP37100F, S1-CAP37100R
EMERSON: 1874, AOS: FSE1028S, GE: 3204
164.11
187.32
124.82
130.18
153.39
180.18
201.61
178
Source 1 Motors
SINGLE HORSEPOWER BLOWER MOTORS
Features:
• 2.5” dia. hub rings included
• Continuous duty, air over
• Use s 370V capacitors
•
•
•
•
•
•
Electrical reversing plug
Class B insulation
Quiet operation
Rotation reversible
Single phase
2-year warranty!
Specifications:
60 Hz
RATED
SOURCE 1 PART NO.
HP
RPM SPEED AMPS LRA
FLA
S1-FHM3583
S1-FHM3584
S1-FHM3585
S1-FHM3586
S1-FHM3587
S1-FHM3588
S1-FHM3589
S1-FHM3590
S1-FHM3595
S1-FHM3596
1/4
1/4
1/3
1/3
1/2
1/2
3/4
3/4
1
1
1075
1075
1075
1075
1075
1075
1075
1075
1075
1075
6.3
2.7
8.2
3.9
12.7
6.8
13.7
7.3
12.6
5.59
3
3
3
3
3
3
3
3
3
3
4.9
2.1
6.7
3.1
9.7
5.2
11.2
5.3
12.6
5.59
10
4.3
13.1
6.4
20
10.6
22.7
11.1
24.5
10.5
VOLTS BEARING
TYPE
115
SLEEVE*
208/230 SLEEVE*
115
SLEEVE*
208/230 SLEEVE*
115
SLEEVE*
208/230 SLEEVE*
115
SLEEVE*
208/230 SLEEVE*
115
BALL
208/230
BALL
RUN CAPACITOR
REPLACES
MLP $
S1-CAP37050F, S1-CAP37050R
S1-CAP37050F, S1-CAP37050R
S1-CAP37050F, S1-CAP37050R
S1-CAP37050F, S1-CAP37050R
S1-CAP37050F, S1-CAP37050R
S1-CAP37050F, S1-CAP37050R
S1-CAP37150F
S1-CAP37100F, S1-CAP37100R
S1-CAP37200F
S1-CAP37150F
EMERSON: 1863, AOS: DL1026, GE: 3583
EMERSON: 1971, AOS: D1026, GE: 3584
EMERSON: 1864, AOS: DL1036, GE: 3585
EMERSON: 1972, AOS: D1036, GE: 3586
EMERSON: 1865, AOS: DL1056, GE: 3587
EMERSON: 1973, AOS: D1056, GE: 3588
EMERSON: 8904, AOS: DL1076, GE: 3589
EMERSON: 8905, AOS: D1076, GE: 3590
EMERSON: 8906, AOS: BDL1106, GE: 3595
AOS: BD1106, GE: 3596
132.25
132.96
148.82
148.89
185.54
185.54
190.18
194.14
264.93
264.93
BLOWER
SOURCE 1 PART NO.
VOLTAGE
HZ
RPM
MAX FLA
BEARINGS
LEADS
MLP $
S1-FHM3463
S1-FHM3464
S1-FHM3466
S1-FHM3467
115V
208/230V
115V
208/230V
60
60
60
60
1075
1075
1075
1075
8.9
4.5
13.7
8.0
BALL
BALL
BALL
BALL
36”
36”
36”
36”
173.54
177.57
200.43
205.64
SOURCE 1 PAR T NO.
MAX HP
1/2
1/3
1/4
1/5
1/6
1/2
1/3
1/4
1/5
1/6
3/4
1/2
1/3
1/4
1/5
3/4
1/2
1/3
1/4
1/5
S1-FHM346 3
S1-FHM346 4
S1-FHM346 6
S1-FHM346 7
COOLING
HE ATING
HI
MED-HI; MED-LO
MED-HI
MED-LO
LO
MED-HI; LO
ALL SPEEDS
MED-LO
MED-HI; MED-LO; LO
MED-LO; LO
LO
LO
CAP (MFD)
10
5 OR 7.5
LO
10
5 OR 7.5
MED-LO
ALL SPEEDS
20
LO
MED-HI; MED-LO; LO
MED-LO; LO
LO
10
MED-LO
LO
LO
LO
LO
ALL SPEEDS
MED-HI; MED-LO; LO
MED-LO; LO
LO
20
10
CONDENSER
SOURCE 1 PART NO.
VOLTAGE
HZ
RPM
MAX FLA
BEARINGS
LEADS
MLP $
S1-FHM3465
S1-FHM3469
S1-FHM3468
208/230V
208/230V
208/230V
60
60
60
1075
825
1075
3.5
2.6
4.6
BALL
BALL
BALL
36”
36”
36”
160.29
167.68
187.61
179
CONDENSER
SOURCE 1 PAR T NO.
S1-FHM346 5
S1-FHM346 9
S1-FHM346 8
MAX HP
1/3
1/4
1/5
1/6
1/3
1/4
1/5
1/6
1/2
1/3
1/4
1/5
SPEED TAP
CAP AT 208V LINE (MFD)
7.5
5
HI
LO
HI
10
LO
HI
12.5
LO
180
7.5
10
CAPACITOR SELECTION GUIDE FOR S1-FHM SERIES MULTI-HORSEPOWER MOTORS
MOTOR MODELS
HP
SPEED
1/2
ALL
CAPACITORS
MOTOR MODELS
ALL
SPEED
S1-CAP37100F
S1-CAP37100R
1/3
HI
230
S1-CAP37050R
S1-CAP37075F
208
S1-CAP37075R
1/4
S1-CAP37050F
1/4
MED-HI, MED-LO, LO
S1-FHM3463 AND
S1-FHM3464
S1-CAP37050R
S1-CAP37075F
208
1/5
S1-CAP37050R
S1-CAP37075F
208
1/6
S1-CAP37050F
1/6
LO
1/2
S1-FHM3466
AND
S1-FHM3467
1/3
1/4
1/5
ALL
ALL
MED-HI, MED-LO, LO
MED-LO, LO
LO
LO
230
S1-CAP37050R
S1-CAP37075F
S1-CAP37075R
3/4
LO
230
S1-CAP37075R
CAPACITORS
S1-CAP37075F
S1-CAP37075R
S1-CAP37050F
S1-CAP37050R
S1-CAP37075F
S1-CAP37075R
S1-CAP37050F
S1-CAP37050R
S1-FHM3465
S1-CAP37050F
MED-LO, LO
HI
230
S1-CAP37075R
1/5
VOLTAGE
208
S1-CAP37050F
1/3
HP
1/2
HI
208
1/3
HI
230
S1-CAP37200F
S1-CAP37075F
S1-CAP37075R
S1-CAP37050F
S1-CAP37050R
S1-CAP37075F
S1-CAP37075R
S1-CAP37050F
S1-CAP37050R
S1-CAP37125F
S1-CAP37100F
S1-CAP37100R
S1-CAP37100F
208
S1-FHM3468
S1-CAP37100R
1/4
LO
230
S1-CAP37100F
S1-CAP37125F
S1-CAP37100F
S1-CAP37100R
S1-CAP37100R
208
1/5
S1-CAP37100F
LO
S1-CAP37100R
230
S1-CAP37125F
S1-CAP37100F
S1-CAP37100R
S1-CAP37100F
208
S1-CAP37100R
1/3
S1-CAP37100F
S1-CAP37100R
HI
230
S1-CAP37075F
S1-CAP37075R
208
1/4
S1-CAP37100F
S1-CAP37100R
HI
230
S1-CAP37075F
S1-CAP37075R
S1-FHM3469
208
1/5
S1-CAP37100F
S1-CAP37100R
LO
230
S1-CAP37075F
S1-CAP37075R
208
1/6
S1-CAP37100F
S1-CAP37100R
LO
230
S1-CAP37075F
S1-CAP37075R
181
CAPACITOR SELECTION GUIDE FOR S1-FHM SERIES MULTI-HORSEPOWER MOTORS
DIRECT DRIVE BLOWER MOTORS
S1-FHM3463
Features:
• Reversible rotation
• Ambient: 40°C
• Open enclosure
• 2” x 4.5” shaft (flatted)
This Time Saver motor replaces all motors in the cross reference table below.
• Resilient rings
• Extended thru bolts
• Automatic protector
SOURCE 1 PART NO.
VOLTAGE
RPM
MAX FLA
BEARINGS
LEADS
MLP $
S1-FHM3463
115
1075
8.9
BALL
36”
173.54
182
S1-FHM3463
MAX HP
1/2
1/3
1/4
1/5
1/6
SOURCE 1 PART NO .
S1-FHM346 3
COOLING
HI
HI
MED-HI
MED-LO
LO
HE ATING
MED-LO
MED-LO
LO
LO
LO
CAP (MFD)
10
5
5
5
5
Cross Reference for Time Saver™ S1-FHM3463 - Blower, Direct Drive, 1/6 - 1/2 HP, 115V
SOURCE 1
P ART NO.
S1-1468- 425P
S1-2632 E3129
S1-2632 E3129
S1-7966- 311P
S1-02423 20970 1
S1-02423 22000 0
S1-02423 22070 0
S1-02423 23900 0
S1-02423 23970 0
S1-02425 10170 1
S1-02425 10770 1
S1-02425 87970 0
S1-02425 87970 1
S1-02630 51100 0
S1-2621 A3129
S1-2621 A3129
S1-52432 02600 0
S1-8638- 4129
S1-02417 90370 3
S1-02420 24470 1
S1-02421 62070 0
S1-02421 76770 0
S1-02423 21900 0
S1-02423 21970 0
S1-02424 15070 0
S1-02425 01000 0
S1-02425 01070 0
S1-02425 10570 2
S1-02425 10870 1
S1-02425 10870 2
S1-02425 10870 3
S1-02425 10970 1
S1-02425 10970 2
S1-02425 94270 0
S1-1468- 212P
S1-52432 026-0 00
S1-02417 79300 0
S1-02417 79370 0
S1-02423 21800 0
S1-02423 21870 0
S1-02423 24000 0
S1-02423 24070 0
S1-02423 24100 0
S1-02423 24170 0
S1-02424 15270 0
S1-02425 10370 2
S1-02425 11270 0
S1-02425 11470 0
S1-02431 96900 0
S1-52432 02600 0
S1-8631 A3239
APP
DRIVE
HP
RPM
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
1/6
1/6
1/6
1/6
1/5
1/5
1/5
1/5
1/5
1/5
1/5
1/5
1/5
1/5
1/5
1/5
1/5
1/5
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
860
2
950
MULTI
1050
MULTI
900
1
1075
3
1075
3
1075
3
1075
3
1075
3
1075
3
1075
3
1000
3
1000
2
1000
2
950
MULTI
1050
MULTI
1075 VARIABLE
1050
1050
3
1075
3
1050
2
900
3
1075
3
1075
3
1075
3
1075
3
1075
3
1075
3
1075
3
1075
3
1075
3
1075
3
1075
3
1075
3
1050
1
1075 VARIABLE
1075
3
1075
3
1075
3
1075
3
1075
3
1075
3
1075
3
1075
3
1075
3
1075
3
1075
3
1075
3
SPEED
1075 VARIABLE
1075
ROTATION VOLTS PH ASE
CCWEOS
CWLE
CWLE
CCWEOS
CCWEOS
CCWEOS
CCWEOS
CCWEOS
CCWEOS
CCWEOS
CCWEOS
CCWEOS
CCWEOS
CCW
CCWLE
CCWLE
REV
CCW
CCWEOS
CWEOS
CCWEOS
CCWEOS
CCWEOS
CCWEOS
REV
CCWEOS
CCWEOS
CCWEOS
CCWEOS
CCWEOS
CCWEOS
CCWEOS
CCWEOS
CCWEOS
CCWEOS
REV
CCWEOS
CCWEOS
CCWEOS
CCWEOS
CCWEOS
CCWEOS
CCWEOS
CCWEOS
REV
CCWEOS
CCWEOS
CCWEOS
CCWEOS
REV
CW
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
BE ARING
ENCLOSURE
ORIENT
1
HZ
60
FRAME
48
SLEEVE
OPEN
VSUDH
1
1
1
1
1
1
1
1
1
1
1
60
60
60
60
60
60
60
60
60
60
60
42
48
48
48
48
48
48
48
48
48
42
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
OPEN
OPEN
ODP
ODP
ODP
ODP
ODP
ODP
ODP
ODP
ODP
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
1
60
48
BALL
OPEN
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
42
48
48
42
48
48
48
48
48
48
48
48
48
48
48
42
48
48
48
48
48
48
48
48
48
48
48
48
48
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
BALL
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
OPEN
OPEN
OPEN
OPEN
ODP
ODP
OPEN
ODP
ODP
ODP
ODP
ODP
ODP
ODP
ODP
OPEN
OPEN
OPEN
ODP
ODP
ODP
ODP
ODP
ODP
ODP
ODP
OPEN
ODP
OPEN
ODP
1
60
48
BALL
OPEN
SOURCE 1 PART NO.
MLP $
S1-FHM3463
173.54
183
HORIZONTAL
HORIZONTAL
VSUDH
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
S1-FHM3464
Features:
• Ambient: 40°C
• Open enclosure
• 1/2” x 4.5” shaft (flatted)
• Resilient rings
SOURCE 1 PART NO.
VOLTAGE
RPM
MAX FLA
BEARINGS
LEADS
MLP $
S1-FHM3464
208/230
1075
4.5
BALL
36”
177.57
SOURCE 1 PAR T NO.
MAX HP
1/2
1/3
1/4
1/5
1/6
S1-FHM346 4
COOLING
HI
HI
MED-HI
MED-LO
LO
HE ATING
MED-LO
MED-LO
LO
LO
LO
CAP (MFD)
10
5
5
5
5
Cross Reference for Time Saver™ S1-FHM3464 - Blower, Direct Drive, 1/6 - 1/2 HP, 208-230V
SOURCE 1
P ART NO.
S1-02421 63400 0
S1-02421 63470 0
S1-02421 63800 0
S1-02421 63870 0
S1-02412 73670 0
S1-02416 69570 0
S1-02419 15070 0
S1-02423 22370 0
S1-02424 77300 0
S1-02424 77370 0
S1-52432 02500 0
S1-02421 52200 0
S1-02421 52670 0
S1-02424 15170 0
S1-02425 98200 0
S1-02427 86600 0
S1-52432 02500 0
S1-02415 64300 1
S1-02416 46170 0
S1-02420 35700 0
S1-02421 63900 0
S1-02421 63970 0
S1-02424 15370 0
S1-02424 50470 0
S1-02424 50470 0
S1-02424 77200 0
S1-02424 77270 0
S1-02425 10670 1
S1-02425 23700 0
S1-02425 23770 0
S1-02425 37470 0
S1-02425 82370 0
S1-02425 95200 1
S1-02425 98300 0
S1-02426 08600 0
S1-02427 60700 0
S1-02427 86800 0
S1-52432 02500 0
APP
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
DRIVE
HP
RPM
SPEED
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
1/6
1/6
1/6
1/6
1/5
1/5
1/5
1/5
1/5
1/5
1/5
1/4
1/4
1/4
1/4
1/4
1/4
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
925
925
1050
1050
1075
1050
1075
1075
1075
1075
1075
1075
1075
1075
1075
1075
1075
1075
825
1075
895
895
1075
1075
1075
1075
1075
1075
1075
1075
1075
925
900
1075
1075
925
1075
1075
1
1
1
1
3
2
3
4
3
3
VARIABLE
3
1
3
3
3
VARIABLE
3
1
3
1
1
3
3
3
3
3
3
3
3
3
3
3
3
3
4
3
VARIABLE
ROTATION
CWEOS
CWEOS
CCWEOS
CWEOS
CWEOS
CWEOS
CCWEOS
CCWEOS
REV
CCWEOS
CWEOS
REV
CCWEOS
CCWLE
REV
CCW
CWEOS
CCWEOS
CCWEOS
CCWEOS
REV
CWEOS
CWEOS
CCWEOS
CCWEOS
CWEOS
CWEOS
CWEOS
CWEOS
CWEOS
CCWEOS
CCWEOS
CCWEOS
CCWEOS
CCWLE
REV
184
VOLTS
PH ASE
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
HZ
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
50
60
60
60
60
60
60
60
60
60
60
60
60
60
60
FRAME BE ARING ENCLOSURE
42
42
48
48
48
42
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
BALL
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
BALL
BALL
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
BALL
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
BALL
TEAO
TEAO
OPEN
OPEN
OPEN
OPEN
ODP
ODP
OPEN
OPEN
OPEN
OPEN
OPEN
SE
OPEN
OPEN
OPEN
OPEN
ODP
OPEN
OPEN
OPEN
ODP
ODP
OPEN
ODP
ODP
OPEN
OPEN
OPEN
OPEN
OPEN
SE
OPEN
ORIENT
VSUD
VSUD
HORIZONTAL
VSUDH
HORIZONTAL
VSUDH
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
VSUD
HORIZONTAL
VSD
VSUD
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
VSD
VSD
VSD
HORIZONTAL
S1-FHM3466
Features:
• Ambient: 40°C
• Open enclosure
SOURCE 1 PART NO.
VOLTAGE
S1-FHM3466
115
SOURCE 1 PAR T NO.
RPM
1075
MAX HP
3/4
1/2
1/3
1/4
1/5
S1-FHM346 6
MAX FLA
• Resilient rings
BEARINGS
LEADS
BALL
36”
13.7
COOLING
HI
HI
MED-HI
MED-LO
LO
HE ATING
MED-LO
LO
LO
LO
LO
MLP $
200.43
CAP (MFD)
20
10
10
10
10
ross Reference for Time Saver™ S1-FHM3466 - Blower, Direct Drive, 1/5 - 3/4 HP, 115V
SOURCE 1P ART NO.
S1-02423 20970 1
S1-02423 22000 0
S1-02423 22070 0
S1-02423 23900 0
S1-02423 23970 0
S1-02425 10170 1
S1-02425 10770 1
S1-02425 87970 0
S1-02425 87970 1
S1-02630 51100 0
S1-2621 A3129
S1-2621 A3129
S1-52432 02200 0
S1-8638- 4129
S1-02417 90370 3
S1-02420 24470 1
S1-02421 62070 0
S1-02421 76770 0
S1-02423 21900 0
S1-02423 21970 0
S1-02424 15070 0
S1-02425 01000 0
S1-02425 01070 0
S1-02425 10570 2
S1-02425 10870 1
S1-02425 10-70 2
S1-02425 10870 3
S1-02425 10970 1
S1-02425 10-70 2
S1-02425 94270 0
S1-1468- 212P
S1-52432 02200 0
S1-02417 79300 0
S1-02417 79370 0
S1-02423 21800 0
S1-02423 21870 0
S1-02423 24-00 0
S1-02423 24070 0
S1-02423 24100 0
S1-02423 24170 0
S1-02424 15270 0
S1-02425 10370 2
S1-02425 11270 0
S1-02425 11470 0
S1-02431 96900 0
S1-52432 02200 0
S1-8631 A3239
S1-02423 21100 3
S1-02424 15670 0
S1-02424 15670 0
S1-02426 00200 0
S1-02427 60100 0
S1-02629 07400 0
S1-02632 25900 0
S1-2970 A3249
APP
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
DRIVE
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
HP
1/5
1/5
1/5
1/5
1/5
1/5
1/5
1/5
1/5
1/5
1/5
1/5
1/5
1/5
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
RPM
1075
1075
1075
1075
1075
1075
1075
1000
1000
1000
950
1050
1075
1050
1050
1075
1050
900
1075
1075
1075
1075
1075
1075
1075
1075
1075
1075
1075
1075
1050
1075
1075
1075
1075
1075
1075
1075
1075
1075
1075
1075
1075
1075
1075
1075
1060
1075
1100
1060
1080
1075
1075
1100
SPEED
ROTATION
3
CCWEOS
3
CCWEOS
3
CCWEOS
3
CCWEOS
3
CCWEOS
3
CCWEOS
3
CCWEOS
3
CCWEOS
2
CCWEOS
2
CCW
MULTI
CCWLE
MULTI
CCWLE
VARIABLE
REV
CCW
3
CCWEOS
3
CWEOS
2
CCWEOS
3
CCWEOS
3
CCWEOS
3
CCWEOS
3
REV
3
CCWEOS
3
CCWEOS
3
CCWEOS
3
CCWEOS
3
CCWEOS
3
CCWEOS
3
CCWEOS
3
CCWEOS
3
CCWEOS
1
CCWEOS
VARIABLE
REV
3
CCWEOS
3
CCWEOS
3
CCWEOS
3
CCWEOS
3
CCWEOS
3
CCWEOS
3
CCWEOS
3
CCWEOS
3
REV
3
CCWEOS
3
CCWEOS
3
CCWEOS
CCWEOS
VARIABLE
REV
CW
3
CCWEOS
3
REV
4
CWEOS
3
CCWEOS
3
CCWEOS
3
CCWEOS
3
REV
4
CCWEOS
185
VOLTS PH ASE
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
115
115
1
115
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
115
1
115
115
1
115
1
115
1
115
1
115
1
115
1
115
1
115
1
HZ FRAME
60
48
60
48
60
48
60
48
60
48
60
48
60
48
60
48
60
48
60
42
BE ARING ENCLOSURE ORIENT
SLEEVE
OPEN
HORIZONTAL
SLEEVE
ODP
HORIZONTAL
SLEEVE
ODP
HORIZONTAL
SLEEVE
ODP
HORIZONTAL
SLEEVE
ODP
HORIZONTAL
SLEEVE
ODP
HORIZONTAL
SLEEVE
ODP
HORIZONTAL
SLEEVE
ODP
HORIZONTAL
SLEEVE
ODP
HORIZONTAL
ODP
HORIZONTAL
60
48
SLEEVE
OPEN
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
42
48
48
42
48
48
48
48
48
48
48
48
48
48
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
OPEN
OPEN
OPEN
OPEN
ODP
ODP
OPEN
ODP
ODP
ODP
ODP
ODP
ODP
ODP
ODP
OPEN
OPEN
OPEN
ODP
ODP
ODP
ODP
ODP
ODP
ODP
ODP
OPEN
ODP
OPEN
ODP
60
48
SLEEVE
OPEN
60
60
60
60
60
60
60
60
48
48
48
48
48
56
48
48
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
OPEN
OPEN
OPEN
ODP
OPEN
AO
OPEN
OPEN
48
42
48
48
48
48
48
48
48
48
48
48
48
48
48
SLEEVE
SLEEVE
HORIZONTAL
HORIZONTAL
VSUDH
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
S1-FHM3467
Features:
• Resilient rings
• Ambient: 40°C
• Open enclosure
SOURCE 1 PART NO.
VOLTAGE
RPM
MAX FLA
BEARINGS
LEADS
S1-FHM3467
208/230
1075
8.0
BALL
36”
SOURCE 1 PART NO.
MAX HP
COOLING
3/4
HI
1/2
HI
S1-FHM3467
1/3
MED-HI
1/4
MED-LO
1/5
LO
Cross Reference for Time Saver™ S1-FHM3467 - Blower, Direct Drive, 1/5 - 3/4 HP, 208-230V
SOURCE 1
P ART NO.
S1-02412 73670 0
S1-02416 69570 0
S1-02419 15070 0
S1-02423 22370 0
S1-02424 77300 0
S1-02424 77370 0
S1-52432 02300 0
S1-02421 52200 0
S1-02421 52670 0
S1-02424 15170 0
S1-02425 98200 0
S1-02427 86600 0
S1-52432 02300 0
S1-02415 64300 1
S1-02416 46170 0
S1-02420 35700 0
S1-02421 63900 0
S1-02421 63970 0
S1-02424 15370 0
S1-02424 50470 0
S1-02424 50470 0
S1-02424 77200 0
S1-02424 77270 0
S1-02425 10670 1
S1-02425 23700 0
S1-02425 23770 0
S1-02425 37470 0
S1-02425 82370 0
S1-02425 95200 1
S1-02425 98300 0
S1-02426 08600 0
S1-02427 60700 0
S1-02427 86800 0
S1-52432 02300 0
S1-02421 67000 0
S1-02421 67070 0
S1-02424 15770 0
S1-02424 50670 0
S1-02424 50670 0
S1-02425 37170 0
S1-02425 97300 0
S1-02425 98500 0
S1-02426 09700 0
APP
DRIVE
HP
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
BLOWER
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
1/5
1/5
1/5
1/5
1/5
1/5
1/5
1/4
1/4
1/4
1/4
1/4
1/4
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
RPM
1075
1050
1075
1075
1075
1075
1075
1075
1075
1075
1075
1075
1075
1075
825
1075
895
895
1075
1075
1075
1075
1075
1075
1075
1075
1075
925
900
1075
1075
925
1075
1075
1050
1050
1075
1075
1075
1075
1075
1130
1050
HEATING
MED-LO
LO
LO
LO
LO
MLP $
205.64
CAP (MFD)
20
10
10
10
10
SPEED
ROTATION
VOLTS PH ASE HZ FRAME BE ARING ENCLOSURE
3
2
3
4
3
3
VARIABLE
3
1
3
3
3
VARIABLE
3
1
3
1
1
3
3
3
3
3
3
3
3
3
3
3
3
3
4
3
VARIABLE
3
3
3
3
3
3
3
3
3
CCWEOS
CWEOS
CWEOS
CWEOS
CCWEOS
CCWEOS
REV
CCWEOS
CWEOS
REV
CCWEOS
CCWLE
REV
CCW
CWEOS
CCWEOS
CCWEOS
CCWEOS
REV
CWEOS
CWEOS
CCWEOS
CCWEOS
CWEOS
CWEOS
CWEOS
CWEOS
CWEOS
CCWEOS
CCWEOS
CCWEOS
CCWEOS
CCWLE
REV
CCWEOS
CCWEOS
REV
CWEOS
CWEOS
CWEOS
CCWEOS
CCWEOS
CCWEOS
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
186
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
50
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
50
60
60
60
60
60
48
48
48
42
48
48
48Y
48
48
48
48
48
48Y
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48Y
48
48
48
48
48
48
48
48
48
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
BALL
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
BALL
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
OPEN
OPEN
OPEN
OPEN
ODP
ODP
OPEN
OPEN
OPEN
OPEN
OPEN
SE
OPEN
OPEN
OPEN
OPEN
ODP
OPEN
OPEN
OPEN
ODP
ODP
OPEN
ODP
ODP
OPEN
OPEN
OPEN
OPEN
OPEN
SE
OPEN
ODP
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
ODP
OE
ORIENT
HORIZONTAL
VSUDH
HORIZONTAL
VSUDH
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
VSUD
HORIZONTAL
VSD
VSUD
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
VSD
VSD
VSD
HORIZONTAL
VSD
VSD
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
HORIZONTAL
TOTALLY ENCLOSED CONDENSER FAN MOTOR
S1-FHM3465
Features:
• Ambient: 60°C
• Totally enclosed
• 1/2” x 6” shaft (double flat)
• Mounting holes in shell
SOURCE 1 PART NO.
VOLTAGE
RPM
MAX FLA
BEARINGS
LEADS
MLP $
S1-FHM3465
208/230
1075
2.8
BALL
36”
160.29
SOURCE 1 PART NO .
SPEED TAP
HI
HI
LO
LO
MAX HP
1/3
1/4
1/5
1/6
S1-FHM346 5
7.5
7.5
7.5
7.5
5
5
5
5
Cross Reference for Time Saver™ S1-FHM3465 - Condenser Fan, Direct Drive, 1/6 - 1/3 HP, 208/230V
SOURCE 1
PART NO.
S1-02421720700
S1-02423203700
S1-02424092000
S1-02424092700
S1-02426006000
S1-02426021000
S1-1468-216P/A
S1-02420795700
S1-02420795700
S1-02424769000
S1-02416076700
S1-02423294700
S1-02423965000
S1-02424158700
S1-02424160700
S1-02424170700
S1-02424189700
S1-02425070700
S1-02425119701
S1-02425119701
S1-02425829700
S1-02425829700
S1-02425831700
S1-02425831700
S1-02425962000
S1-02425962000
S1-02426020700
S1-02426022000
S1-02427500000
S1-02427596000
S1-02427885000
S1-02427889000
S1-1468-215P/B
S1-32425801002
S1-02419186700
S1-02420080700
S1-02421635000
S1-02421635000
S1-02421635700
S1-02421635700
S1-02424096000
S1-02424117001
S1-02424162700
S1-02424163700
S1-02424171700
S1-02424191700
S1-02424981000
S1-02424981700
S1-02425378700
S1-02425820700
S1-02427886000
S1-02434549000
S1-52434586000
S1-524-4587000
S1-52434588000
APP
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
CONDENSER
DRIVE
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
HP
RPM
SPEED
1/6
1/6
1/6
1/6
1/6
1/6
1/6
1/5
1/5
1/5
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/3
1/6-1/3
1/6-1/3
1/2-1/5
825
1100
1075
1075
1060
850
850
1075
1075
1075
1075
1075
1075
1075
1075
1075
1075
1120
850
850
1075
1075
850
850
850
850
1100
850
850
850
1075
1075
1100
1120
1075
1075
900
900
900
900
1075
1120
1075
1075
1075
1075
1100
1100
1075
1100
1075
1100
1075
825
1075
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
2
1
2
1
1
3
1
1
1
ROTATION VOLTS
CWEOS
CWEOS
REV
REV
CWEOS
CWEOS
CWEOS
CWLE
CWLE
CCWEOS
CWEOS
CWEOS
CWEOS
REV
REV
REV
REV
CWEOS
CWEOS
CWEOS
CWEOS
CWEOS
CWEOS
CWEOS
CWEOS
CWEOS
CWEOS
CWEOS
CWEOS
CWEOS
REV
REV
CWEOS
CWEOS
CWEOS
CWEOS
REV
CWEOS
REV
REV
REV
REV
CCWEOS
CCWEOS
CCWEOS
CWEOS
REV
CWEOS
187
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
208-230
PHASE
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
HZ FRAME BEARING ENCLOSURE
60
60
60
60
60
60
60
50
60
60
60
60
60
60
60
60
60
60
50
60
50
60
50
60
50
60
60
60
60
60
60
60
60
60
60
60
50
60
50
60
60
60
60
60
60
60
60
60
60
60
60
60
ORIENT
48
48
48
48
48
48
48
42
42
48
48
48
48
48
48
48
SLEEVE
SLEEVE
OEBOS
OEBOS
VSU
VSD
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
BALL
SLEEVE
SLEEVE
SLEEVE
BALL
SLEEVE
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
BALL
SLEEVE
SLEEVE
BALL
BALL
BALL
BALL
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
SLEEVE
ODP
TEAO
OPEN
ODP
ODP
TEAO
ODP
TEAO
TEAO
OA
OEBOS
AO
ODP
TEAO
OEBOS
OEBOS
OEBOS
OEBOS
OEBOS
OEBOS
OEBOS
OEBOS
TEAO
TEAO
TEAO
TEAO
OEBOS
OEBOS
OEBOS
TEAO
OEBOS
OEBOS
HORIZONTAL
VSD
VSU
HORIZONTAL
HORIZONTAL
VSU
VSUH
VSD
VSD
VSU
VSU
VSD
VSUDH
VSD
VSD
VSD
VSD
VSD
VSD
VSD
VSD
VSD
VSD
VSD
VSD
VSD
VSU
VSD
VSU
VSD
VSU
HORIZONTAL
48
48
48
48
SLEEVE
SLEEVE
BALL
SLEEVE
48
48
48
48
48
48
SLEEVE
SLEEVE
BALL
SLEEVE
SLEEVE
SLEEVE
TEAO
AO
OEBOS
AO
ODP
TEAO
TEAO
VSD
VSU
VSU
VSD
VSUDH
VSU
VSU
OEBOS
OEBOS
OEBOS
VSD
VSU
VSU
AO Smith Motors
AO SMITH BLOWER MOTORS
Features:
• Auto Protector
• Open Construction
• Standard Efficiency
• 26” Leads
• Class B Insulation
• PSC
• 2-1/4” Rings with 2-1/2” Adapters
• 48 Frame (5-5/8” dia.)
• Continuous Air Over
• 60 Hz only
• Lead Reversible
• Sleeve Bearing included
• 40°C Ambient
SOURCE 1 PART NO.
HP
RPM
SPEED
ROTATION
VOLTS
PHASE
HZ
MLP $
S1-D1026
S1-D1036
S1-D1056
S1-D1076
S1-DL1026
S1-DL1036
S1-DL1056
S1-DL1076
1/4
1/3
1/2
3/4
1/4
1/3
1/2
3/4
1075
1075
1075
1075
1075
1075
1075
1075
3
3
3
3
3
3
3
3
REV
REV
REV
REV
REV
REV
REV
REV
208/230
208/230
208/230
208/230
115
115
115
115
1
1
1
1
1
1
1
1
60
60
60
60
60
60
60
60
157.14
163.71
157.11
189.25
158.93
165.25
199.04
227.79
AO SMITH FAN MOTORS
Features:
• All Angle Mount
• Ext. Thru Bolts—Both Ends
• Sleeve Bearing
• 26” Leads
• Auto Protector
• 1/2” Dia. Shaft, Dbl. Flat
• 48 Frame (5-5/8” Dia.)
• Permanent Split Capacitor
• 60°C Ambient
• Energy Efficient
• 4, 6 & 8-Pole
• Reversing Plug
SOURCE 1 PART NO.
HP
RPM
SPEED
ROTATION
VOLTS
PHASE
HZ
MLP $
S1-FSE1016SV1
S1-FSE1026SV1
S1-FSE1036SV1
S1-FSE1038S
S1-FSE1056SV1
S1-FSE1076SV1
1/6
1/4
1/3
1/3
1/2
3/4
1075
1075
1075
825
1075
1075
1
1
1
1
1
1
REV
REV
REV
REV
REV
REV
208/230
208/230
208/230
208/230
208/230
208/230
1
1
1
1
1
1
60
60
60
60
60
60
142.93
146.54
156.36
223.93
176.89
190.43
188
AO Smith Motors
AO SMITH HEATMASTER CONDENSER FAN MOTORS
Features:
• Energy-efficient PSC design
• 3-year warranty from date of manufacture date code, or 2 years from the date of installation
• High-temperature UL/CSA-approved overload protector
• UL/CSA-approved Class F insulation
• 70°C (158°F) max. ambient
• Water-resistant reversing plug
• Double-sealed ball bearings, or dependable all-angle sleeve bearings
• All-angle mount
• Mounts by belly band, adjustable extended thru-bolts, or Rheem mounting holes, with screws supplied
• Lead length 36”
• 60 Hertz
• Continuous duty, air over
• UL and CSA approved
SOURCE 1 PART NO.
HP
RPM
ROTATION
SPEED
VOLTS
PHASE
HZ
S1-FE1008SF
S1-FE1018SF
S1-FE1028SF
S1-FE1038SF
S1-FE1058SF
S1-FSE1028SF
S1-ORM5458BF
S1-ORM5488BF
1/6
1/4
1/3
1/2
3/4
1/4
1/3–1/6
1/8–1/8
825
825
825
825
825
825
1075
825
REV
REV
REV
REV
REV
REV
REV
REV
1
1
1
1
1
1
1
1
208/230
208/230
208/230
208/230
208/230
208-230
208/230
208/230
1
1
1
1
1
60
60
60
60
60
60
60
60
1
1
NOTES
311,370,$
MLP $
246.86
282.86
298.54
342.39
410.86
201.43
210.14
274.89
Note:
$ Energy Efficient
311. 1/2” dia. shaft, single flat
370. 48” leads
AO SMITH MASTERFIT UNIVERSAL REPLACEMENT MOTORS
Features:
• Energy Efficient
• Different Capacitor/Speed Combinations
• Designed for 370V Capacitor (not furnished)
• Ball and Sleeve Bearing
• Rotation Reversible
• Resilient Rings on Blower Motors
• Extended Thru Bolts
• Automatic Protector
• 48 Frame
• Single Phase
• Continuous Duty Air Over
• Mounts by Belly Band, Thru Bolts or Shell Holes
• Rheem Mounting Holes in Shell
• Shaft length: all 1/2" x 5" except S1-FE6000 1/2" x 6"
• Blower motors: Ambient - 40°C; Open Dripproof
• Fan motors: Ambient - 60°C; Totally Enclosed Air Over
SOURCE 1 PART NO.
APPLICATION
HP
RPM
SPEED
VOLTS
HZ
S1-FD6000
S1-FD6001
S1-FDL6001
S1-FDL6002
S1-FE6000F
S1-FE6001
S1-FE6002
DIRECT DRIVE INDOOR BLOWER
1/2–1/6
3/4–1/5
1/2–1/6
3/4–1/5
1/3~1/5
1/3–1/6
1/2–1/5
1075
1075
1075
1075
1075
825
1075
4
4
4
4
2
2
2
208/230
208/230
115
115
208-230
208/230
208/230
60
60
60
60
60
60
60
TOTALLY ENCLOSED CONDENSER FAN
TOTALLY ENCLOSED CONDENSER FAN
Notes:
1. Item to be discontinued when stock is depleted
2. Ball bearing
189
NOTES
1,2,206
MLP $
205.39
230.07
202.82
228.89
205.00
270.57
254.64
AO Smith Motors
5" DIAMETER SINGLE SHAFT OPEN FAN/BLOWER MOTORS
Furnaces – Air Handlers – Fan Coils – Air Conditioning
Features:
• Auto Protector
• 1/2” Dia. Flatted Shaft
• 42 Frame
• 60 Hz
• Sleeve Bearing
OEM Replacements for: Reznor, Luxaire, Armstrong, Payne, Day & Night, Bryant, Bohn, Intertherm,
Kodair, Dole, Coleman, Janitrol, Steward Warner, International Heater Etc.
SOURCE 1 PART NO.
HP
RPM
SPEEDS
VOLTS
AMPS
ROTATION
CAPACITOR
DIM. REF.
NOTES
MLP $
S1-390
1.4~1.5~1.7
1050
3
115
3.7-3.1-2.4
REV
7.5MFD-370V
1
9,26
159.32
Notes:
9. Reversing plug
26. Extended thru bolts, shaft end
Ref.
1
BM
4.25
C
10.25
N
6.00
R
CAPACITOR START RESILIENT BASE MOTORS
Features:
• High Start Torque
• 2, 4 and 6 Pole
• 40° C Ambient
• Reversible
• 60 Hz
Applications: Compressors, pumps, conveyors, milking machines, blowers, fans
SOURCE 1 PART NO.
HP
S1-BK1054
S1-RB1074A
S1-RB1104AV1
1/2
3/4
1
RPM
VOLTS
FULL LOAD FRAME BEARINGS ENCLOSURE INSUL. OVERLOAD "C" "AG"
NOTES
AMPS
CLASS PROTECTOR DIM DIM
1725
115/208-230
8.8/4.4
56
Ball
ODP
B
Auto
11.6 9.6 55,61,66,78
1725
115/208-230
13.0/6.5
56
Ball
ODP
B
Auto
10.8 8.8
1725/1425 115/208-230 14.4/6.6-7.2
56
Ball
Open
B
Auto
11.8 9.8
6, New!
MLP $
459.32
472.64
495.93
Notes:
6. 50/60 HZ
55. Terminal board
61. Start capacitor inside
66. Sealed switch design
78. Moderate start torque
Shaft Dimensions
48 = 1/2” Flat x 1-5/8”
56 = 5/8” Keyed x 1-7/8”
THREE PHASE ODP RESILIENT BASE MOTORS
Pumps - Blowers - Conveyors - Industrial Duty
Features:
• Ball Bearing
• 40° C Ambient
• Continuous Duty
• 60 HZ
SOURCE 1 PART NO.
HP
RPM
VOLTS
S1-BK3074
S1-RB3104A
S1-RB3154AV1
3/4
1
1-1/2
1725
1725
1725
208-230/460
208-230/460
208-230/460
FULL LOAD SERVICE
AMPS
FACTOR
2.9/1.45
1.25
3.6/1.8
1.25
5.0/2.5
1.15
Notes:
6. 60/50 Hz
15. 56HZ = 7/8” key x 2-5/16” shaf t
48. 1.0 Serv ice f act or at 50 Hz
Shaft Dimensions
56 = 5/8” Keyed x 1-7/8”
56H = 5/8” Keyed x 1-7/8”
190
FRAME
56H
56H
56HZ
INSUL.
CLASS
B
B
B
OVERLOAD "C" DIM
PROTECTOR
Auto
11.9
Auto
11.8
Auto
12.3
"AG"
DIM
10.0
9.8
10.0
NOTES
MLP $
6
6,15,48
511.36
518.68
572.07
AO Smith Motors
6-1/2" DIAMETER STOCK MOTORS
56 Frame Vertical Condenser Fan Continuous Duty, Air Over
Features:
• Auto Protector
• Class B or F Moisture-Resistant Insulation
• Double Sealed Ball Bearing
• Three Phase
• Quick-Connect Design
• Reversible
• 5/8” Dia. Shaft with both Keyway and Flat
• 60 Hz
Three Phase - Electrically Reversible
SOURCE 1 PART NO.
HP
RPM
VOLTS
AMPS
S1-H667
S1-H686
S1-H697
S1-H767
1
1
1-1/2
1-1/2
1140
850
1140
1140
460/200-230
460/200-230
460/200-230
460/200-230
2.6/5.3-5.2
2.0/4.4-4.0
2.6/5.4-5.2
3.0/5.8-6.0
SERVICE FRAME
FACTOR
1.00
56Y
1.00
56Y
1.15
56Y
1.00
56Y
INSUL.
CLASS
B
B
B
B
AMBIENT °C ENCLOSURE
60
60
70
60
OAO
OAO
TEAO
ODP
DIM. REF.
4
2
8
4
NOTES
163
MLP $
502.11
426.39
523.71
513.57
Notes:
163. No keyway, double flat
Approximate Dimensions
Ref.
BM
C
N
2
9.36
14.24 4.88
4
10.81
16.81 6.00
8
11.25
17.44 6.19
Y
X
1.00
OUTDOOR BALL BEARING CONDENSER FAN MOTORS
Three-Phase
Features:
Important: Use amps as well as HP for replacement reference.
• Auto Protector
• Base Mounted
• Ball Bearing
• Capac. Mounted (Single Phase)
• Open Lead End Only
• Reversible
• Service Factor
• 60Hz
THREE-PHASE
SOURCE 1 PART NO.
HP
RPM
VOLTS
S1-H685
1
1140
460/200-230
MAX. AMPS FRAME
1.9/4.2-3.8
56Y
Approximate Dimensions
BM
8.86
C
12.86
N
4.00
H
3.50
BA
2.75
2F
3.00
191
SHAFT
5/8” Key & Flat
AMBIENT "C" ENCLOSURE ROTATION BASE
60
TEAO
RCC
RCC
MLP $
493.36
AO Smith Motors
3-IN-1™ 3.3” DIAMETER PSC MOTOR
Features:
• Easy-to-Read Connection Diagram Attached to White Lead Wire
• Now! Four Studs on Each End
• 40° C Ambient
• 60/50 HZ
• UL and CSA Recognized
• Replaces 1/12, 1/15, 1/20 HP PSC and Low Efficient Shaded Pole Designs
• Direct Drop-in Replacement for walk-in cooler evaporator fans
SOURCE 1 PART NO.
HP
VOLTS
AMPS
RPM
SPEEDS
BM DIM
S1-9721
1/12,1/15,1/20
115/208-230
1.1/0.5
1550
1
3.60
SHAFT DIA. & ROTATION
LENGTH
5/16 x 3-1/4
Rev.
WT.
MLP $
4.75
172.75
5" DIAMETER MULTIFIT® CONDENSER FAN MOTORS
Features:
• All angle mount
• Ball bearing
• Class B insulation
• Double sealed ball bearings
• Energy efficient PSC design $
• Reversing plug
• Single speed
• 60° C ambient
• 60 HZ
• 36” leads
• 1/2” Dia. flatted shaf
• Multi-horsepower,one simple connection
• Multi-mounting system
One simple connection eliminates having to select various speeds or change capacitor sizes.
SOURCE 1 PART NO.
HP
RPM
SPEEDS
VOLTS
AMPS
CAPACITOR
MLP $
S1-9722
S1-9723
1/12 - 1/8
1/4, 1/5, 1/6
1075
1075
1
1
208-230
208-230
0.9
2.0
2MDV4
7.5MFD/370V
216.50
171.18
O.E.M. - DIRECT REPLACEMENT
SOURCE 1 PART NO.
HP
RPM
SPEEDS
S1-H978
SPL
1140
1
VOLTS
AMPS
208-230/460/575 5.5/2.8-3.4
ROTATION
CAPACITOR
REV
3 Phase
Notes:
2. Ball bearing
192
SHAFT DIA. &
LENGTH
5.8" x 3-5/8"
MOTOR
DIA.
6-1/2”
"A" DIM. NOTES
11-3/8”
2
MLP $
597.07
5” Diameter Single Shaft Open Fan/Blower Motors
Furnaces – Air Handlers – Fan Coils – Air Conditioning Motors
OEM Replacements for: Reznor, Luxaire, Armstrong, Payne, Day & Night, Bryant, Bohn, Intertherm, Kodair, Dole, Coleman, Janitrol,
Steward Warner, International Heater Etc.
Features:
• Auto Protector
•
•
•
•
1/2” Dia. Flatted Shaft
42 Frame
60 Hz
Sleeve Bearing
SOURCE 1 PART NO.
HP
RPM
SPEEDS
VOLTS
AMPS
ROTATION
CAPACITOR
MLP $
S1-CE-391
1/4 - 1/5 - 1/7
1050
3
208-230
1.5-1.2-1.0
REV
7.5MFD-370
159.57
5-5/8” Diameter (Totally Enclosed) - Outdoor Ball and Sleeve Bearing Motors
Condensers – Heat Pump – Refrigeration Motors
Features:
• Energy Efficient $
• Class B or Class F Insulation
• Ball or Sleeve Bearing
• 1/2” Dia. Flatted Shaft
• 26” (Minimum) to 48” Leads
• 60 HZ
• All Angle Mount
• 60? or 70? C Ambient
• Auto Protector
• Reversible
• 6 and 8 Pole
• Extended Thru Bolts
SOURCE 1 PART NO.
HP
RPM
SPEEDS
VOLTS
AMPS
ROTATION
CAPACITOR
MLP $
S1-CE-629A
S1-FEH1076SF
1/6
3/4
825
1075
1
1
208-230
460
1
1
REV
REV
5MFD-370V
10MFD/370V
316.11
273.54
Capacitor Start Resilient Base Motors
Features:
• High Start Torque
• Reversible
• 2, 4 and 6 Pole
• 40?C Ambient
• 60 Hz
Applications: Compressors, pumps, conveyors, milking machines, blowers, fans
SOURCE 1 PART NO.
HP
RPM
SPEEDS
VOLTS
AMPS
ROTATION
MLP $
S1-CE-C654
3/4
1725
1
208-230/115
5.4-5.5/11.0
REV
679.71
193
Condenser Fan Motor Single-Phase, PSC
Deluxe Heatmaster Condenser Fan Motor Single-Phase, PSC
Features:
• Patented canopy design, fan blades move cooling air through the motor for extra performance and long life
• Suitable for use with solid state speed control devices
• Electrically reversible, 70°C ambient
• Heavy-duty ball bearings
• Diameter shafts have flat and key
SOURCE 1 PART NO.
HP
RPM
SPEEDS
VOLTS
AMPS
ROTATION
CAPACITOR
MLP $
S1-FC1086F
4/5
1075
1
200-230/460
4.6
REV
G21-909
404.36
Direct Drive Indoor Blower Motor
5-5/8" High Efficiency Indoor Blower Motor
SOURCE 1 PART NO.
HP
RPM
SPEEDS
VOLTS
AMPS
ROTATION
CAPACITOR
MLP $
S1-FD1056
1/2
1075
3
208-230
2.7
REV
2MDV6
214.68
High Temperature Condenser Fan Motor
HeatMaster™ High Temperature Condenser Fan Motor
Features:
• Replaces motors in units by Carrier/Bryant and others
• 48 frame, 1075 RPM
• 1-speed, all angle mount
SOURCE 1 PART NO.
HP
RPM
SPEEDS
VOLTS
AMPS
ROTATION
CAPACITOR
MLP $
S1-FE1056SF
1/2
1075
1
208-230
4
REV
POC10
219.79
O.E.M. – Direct Replacement Motors
Rheem-Ruud Direct Replacement Motors
SOURCE 1 PART NO.
HP
RPM
SPEEDS
VOLTS
AMPS
ROTATION
CAPACITOR
MLP $
S1-CE-ORM1008
S1-CE-ORM10206V1
1/8
1/5
825
1075
1
1
208-230
208-230
0.7
1.4
REV
REV
5MFD/370V
3MFD/370V
289.39
240.57
194
Dayton Motors
Direct Drive Blower Motors
SOURCE 1 PART NO.
HP
RPM
SPEEDS
VOLTS
AMPS
ROTATION
CAPACITOR
MLP $
S1-BDL1106
1
1075
4
115
14.7
CW/CCW
2MDW2
281.57
195
Genteq Motors
ECM Motors
Brushless Direct Drive Blower, ECM
SOURCE 1 PART NO.
HP
RPM
SPEEDS
VOLTS
AMPS
ROTATION
CAPACITOR
MLP $
S1-6005
S1-6010
0.5
1
1000-1380
1000-1380
1
1
115/230
115/230
6.7/4.0
11.0/6.7
CW/CCW
CW/CCW
N/A
N/A
650.11
820.82
Capacitors
Multi-Value Capacitors
SwitchCapTM Dual Multiple Value Capacitor
For HVAC applications including air handlers, heat pumps, condensing units, coolers, refrigeration systems, RTUs and PTACs.
Features:
• 1 unit covers most HVAC applications
FAN 3.0 to 10.5 MFD 450 VAC
HERM 15 to 60 MFD 450 VAC
• Capacitance value are selected by built-in switches, no jumpers to get lost or connected improperly
• Built-in hang tabs. Easy mounting with sheet metals screws
• Easy set-up, 8 switches select 128 values
• 3000 hour life expectancy
SOURCE 1 PART NO.
DESCRIPTION
Shipping Multiple
MLP $
S1-SCAP-60D
DUAL MULTIPLE VALUE CAPACITOR
6
131.86
TURBO CAPACITORS
Turbo® 200 Family of Products
A. TurboTester™—simultaneously test and display MFD values for fan and compressor.
B. The Original Turbo™200 —Technicians can now replace any one of the more than 200 dual capacitors used for HVAC and
maintenance work.
C. Turbo™200 MINI—A permanent replacement for up to 14 popular “fan-sized” values—2.5 mfd to 12.5 mfd
D. Turbo™200X —Replace any one of the higher range of capacitors used in scroll compressors and higher efficiency A/C units
requiring duals such as 70/5 to as high as 90/7.5.
E. Turbolytic™ 50 —the world’s first universal “Motor-Start” capacitor—can replace any one of the most popular values and
voltages.For your safety and performance, the Turbo®200 series has been tested and approved to the highest certification level of
UL Standard 810; 10,000 AFC; PROTECTED. (As required for all “original equipment” motor-run capacitors.)
SOURCE 1 PART NO.
DESCRIPTION
QTY. PER CASE
MLP $
S1-TURBO200
S1-TURBO200MINI
S1-TURBO200X
S1-TURBOLYTIC50
CAP,RUN,2.5-67.5 MFD,TURBO 200
CAP,RUN,2.5-12.5 MFD,TURBO 200 MINI
CAP,RUN,70/5-90/7.5 MFD,TURBO 200X
CAP,START,UNIV,TURBOLYTIC 50
20
50
16
16
137.54
19.89
180.00
158.50
* P ri ce per pi ece
196
Capacitors
SINGLE RUN CAPACITORS
Features:
• Continuous duty for single phase AC motors
• Non PCB liquid filled
• 50 & 60 Hz operation
• Tin plated 1/4 x .032 male terminals
• Internally protected by pressure sensitive interrupter device
• Aluminum case with terne plate steel cover
SOURCE 1 PART NO.
MFD
VOLTS
CAN STYLE
MLP $
S1-CAP37020F
S1-CAP37040F
S1-CAP37050F
S1-CAP37050R
S1-CAP37060F
S1-CAP37075F
S1-CAP37075R
S1-CAP37100F
S1-CAP37100R
S1-CAP37125F
S1-CAP37150F
S1-CAP37175F
S1-CAP37250F
S1-CAP37250R
S1-CAP37300F
S1-CAP37300R
S1-CAP37350F
S1-CAP37400F
S1-CAP37450F
S1-CAP37500F
S1-CAP37550R
S1-CAP37600R
S1-CAP37650R
S1-CAP37700F
S1-CAP37800F
S1-CAP44030F
S1-CAP44040F
S1-CAP44050F
S1-CAP44060F
S1-CAP44075F
S1-CAP44100F
S1-CAP44125F
S1-CAP44150F
S1-CAP44150R
S1-CAP44175F
S1-CAP44200F
S1-CAP44200R
S1-CAP44250F
S1-CAP44250R
S1-CAP44300F
S1-CAP44300R
S1-CAP44350F
S1-CAP44350R
S1-CAP44400F
S1-CAP44400R
S1-CAP44450F
S1-CAP44450R
2.0
4.0
5.0
5.0
6.0
7.5
7.5
10.0
10.0
12.5
15.0
17.5
25.0
25.0
30.0
30.0
35.0
40.0
45.0
50.0
55.0
60.0
65.0
70.0
80.0
3.0
4.0
5.0
6.0
7.5
10.0
12.5
15.0
15.0
17.5
20.0
20.0
25.0
25.0
30.0
30.0
35.0
35.0
40.0
40.0
45.0
45.0
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
440
440
440
440
440
440
440
440
440
440
440
440
440
440
440
440
440
440
440
440
440
440
FLAT
FLAT
FLAT
ROUND
FLAT
FLAT
ROUND
FLAT
ROUND
FLAT
FLAT
FLAT
FLAT
ROUND
FLAT
ROUND
FLAT
FLAT
FLAT
FLAT
ROUND
ROUND
ROUND
FLAT
FLAT
FLAT
FLAT
FLAT
FLAT
FLAT
FLAT
FLAT
FLAT
ROUND
FLAT
FLAT
ROUND
FLAT
ROUND
FLAT
ROUND
FLAT
ROUND
FLAT
ROUND
FLAT
ROUND
3.82
3.89
3.11
3.39
4.14
4.07
3.93
4.46
4.46
5.57
5.68
6.64
7.89
7.00
8.96
8.54
9.39
11.07
13.79
12.93
13.32
14.18
17.46
18.29
20.39
4.07
4.00
3.71
4.21
4.14
4.57
5.68
5.96
6.43
6.86
6.82
7.00
8.04
7.79
9.14
8.89
10.32
9.50
11.43
11.11
11.79
12.14
S1-CAP44500F
S1-CAP44500R
S1-CAP44550F
S1-CAP44600F
S1-CAP44600R
S1-CAP44650R
S1-CAP44700R
S1-CAP44800R
50.0
50.0
55.0
60.0
60.0
65.0
70.0
80.0
440
440
440
440
440
440
440
440
FLAT
ROUND
FLAT
FLAT
ROUND
ROUND
ROUND
ROUND
13.46
13.14
14.18
15.21
14.86
18.21
18.50
19.50
197
Capacitors
DUAL RUN CAPACITORS
MFD
SOURCE 1 PART NO.
COMPR.
FAN
VOLTS
CAN STYLE
MLP $
S1-CAP3704025DR
S1-CAP3705015DF
S1-CAP3705020DF
S1-CAP3705020DR
25.0
15.0
20.0
20.0
4.0
5.0
5.0
5.0
370
370
370
370
ROUND
FLAT
FLAT
ROUND
9.57
8.00
8.86
8.64
S1-CAP3705025DF
S1-CAP3705025DR
S1-CAP3705030DF
S1-CAP3705035DF
S1-CAP3705035DR
S1-CAP3705040DF
S1-CAP3705045DF
S1-CAP3705060DR
S1-CAP3705080DR
S1-CAP3707530DF
S1-CAP3707535DF
S1-CAP3707545DF
S1-CAP3707545DR
S1-CAP3707555DF
25.0
25.0
30.0
35.0
35.0
40.0
45.0
60.0
80.0
30.0
35.0
45.0
45.0
55.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.5
7.5
7.5
7.5
7.5
370
370
370
370
370
370
370
370
370
370
370
370
370
370
FLAT
ROUND
FLAT
FLAT
ROUND
FLAT
FLAT
ROUND
ROUND
FLAT
FLAT
FLAT
ROUND
FLAT
9.86
8.43
10.32
12.21
10.39
13.68
14.36
16.71
20.71
12.11
13.25
17.00
16.64
17.71
S1-CAP3710015DF
S1-CAP3710025DF
S1-CAP3715020DF
S1-CAP4403030DR
S1-CAP4403035DR
S1-CAP4403040DR
S1-CAP4403045DR
S1-CAP4405025DF
S1-CAP4405025DR
S1-CAP4405030DF
S1-CAP4405030DR
S1-CAP4405035DF
S1-CAP4405035DR
S1-CAP4405040DF
S1-CAP4405040DR
S1-CAP4405045DF
S1-CAP4405045DR
S1-CAP4405050DR
S1-CAP4405055DR
S1-CAP4405060DR
S1-CAP4407530DR
S1-CAP4407535DF
S1-CAP4407535DR
S1-CAP4407540DF
S1-CAP4407545DR
S1-CAP4407550DR
S1-CAP4407555DR
S1-CAP4407560DR
S1-CAP4407580DR
15.0
25.0
20.0
30.0
35.0
40.0
45.0
25.0
25.0
30.0
30.0
35.0
35.0
40.0
40.0
45.0
45.0
50.0
55.0
60.0
30.0
35.0
35.0
40.0
45.0
44.0
55.0
60.0
44.0
10.0
10.0
15.0
3.0
3.0
3.0
3.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.5
7.5
7.5
7.5
7.5
5.0
7.5
7.5
8.0
370
370
370
440
440
440
440
440
440
440
440
440
440
440
440
440
440
440
440
440
440
440
440
440
440
440
440
440
440
FLAT
FLAT
FLAT
ROUND
ROUND
ROUND
ROUND
FLAT
ROUND
FLAT
ROUND
FLAT
ROUND
FLAT
ROUND
FLAT
ROUND
ROUND
ROUND
ROUND
ROUND
FLAT
ROUND
FLAT
ROUND
ROUND
ROUND
ROUND
ROUND
9.14
11.39
11.36
10.57
12.07
13.50
14.79
8.89
8.46
10.71
9.29
11.82
10.50
12.68
11.61
14.64
12.46
13.71
14.14
15.07
11.82
13.14
12.89
14.86
16.25
15.36
18.82
18.39
27.18
S1-CAP4410040DR
S1-CAP4410045DR
S1-CAP4410055DR
40.0
45.0
55.0
10.0
10.0
10.0
440
440
440
ROUND
ROUND
ROUND
16.00
17.93
21.18
START CAPACITORS
Features:
• Molded plastic case
• Designed for 20 starts per hour duty cycle
• 50/60 Hz operation
• 4 x .032 male push on terminals
• 15,000 OHM / 2 watt resistor
DIMENSIONS
SOURCE 1 PART NO.
MFD
VOLTS
CAN STYLE
D
H
MLP $
S1-02425071700
S1-02425075700
S1-02426023000
S1-02425191700
S1-02425215700
S1-02425390700
145-175
161-193
297-356
88-108
189-227
270-324
250
250
250
330
330
330
ROUND
ROUND
ROUND
ROUND
ROUND
ROUND
2.06
2.06
2.06
2.06
2.56
2.56
4.38
4.38
4.38
4.38
4.38
4.38
19.71
19.75
35.11
20.79
28.82
35.64
198
Fan Blades
PROPELLER FANS
Features:
• Rotationally balanced
• 1/4 - 28 or 5/16 - 24 sq. hd. set screw (torque to 100 in. lb.)
• Steel hub and spider construction with corrosion protection
• (250 HR. of 5% salt spray)
• Steel blades are corrosion protected (250 HR. of 5% salt spray)
• Air Moving and Conditioning
• Association (AMCA) rated
BLADES
HUB
SOURCE 1 PART NO.
NOM. DIA.
NUMBER OF
PITCH (DEG)
TYPE
S1-02619367000
S1-02619368000
S1-02619369000
S1-02619370000
S1-02619372000
12”
12”
16”
16”
14”
4
4
4
4
4
36
36
43
43
40
ALUM
ALUM
ALUM
ALUM
ALUM
ROTATION
FACING AIR
DISCH.
CCW
CW
CCW
CW
CW
NOM BORE
LOCATION
FIG NO.
NO. OF SET
SCREWS
MLP $
1/2
1/2
1/2
1/2
1/2
INTAKE
INTAKE
INTAKE
INTAKE
INTAKE
1
2
1
2
2
1
1
1
1
1
52.21
48.57
62.93
63.14
63.86
Blower Wheels
DOUBLE INLET SINGLE HUB
Concave Center Plate
Features:
• Concentric to bore within .062 total indicator runout (TIR)
• Balanced for vibration free operation
• (1) set screw (except as noted)
• Concave center plate
• Max RPM = 1750
• NOTE: Torque set screw(s) to 14 to 20 ft. lbs.
NOMINAL
DIMENSIONS
SOURCE 1 PART NO.
MFG.
MFG. PART NO.
DIA.
WIDTH
D
W
NOM. BORE DIA.
S1-02619654012*
LAU
026941-25
11
10
12.25
10.62
.500
* (2) Set screw s, 90° apart.
199
NUMBER OF
BLADES
53
ROTATION
FACING HUB
CW
MATERIAL TYPE
MLP $
PTD STL
189.42
Blower Wheels
DOUBLE INLET SINGLE HUB
Convex Center Plate
Features:
• Concentric to bore within .062 total indicator runout (TIR)
• Balanced for vibration free operation
• (1) set screw (except as noted)
• Convex center plate
• Max RPM = 1750
• NOTE: Torque set screw(s) to 14 to 20 ft. lbs.
NOMINAL
DIMENSIONS
SOURCE 1 PART NO.
MFG.
MFG. PART NO.
DIA.
WIDTH
D
W
NOM. BORE DIA.
S1-02619654014 *
MORRISON
03-55041
11
10
11.93
10.68
.500
NUMBER OF
BLADES
54
ROTATION
FACING HUB
CW
MLP $
MATERIAL
TYPE
PTD STL
114.57
* (2) Set screw s, 90° apart
Rainshields
CONDENSER FAN MOTOR
Rainshields
An inexpensive means to reduce the potential of rain getting into motor bearings on
vertical shaft motor applications.
• Simple press fit on shafts
• 6.75” for closed motors to protect bearings
• 7” with interior cooling blades (effectively reduces motor winding temperature and
protects open motors)
• Primarily for vertical shaft motors on outdoor condensing units but can be used in any
position to keep water from migrating along the shaft
• Used as original equipment on many new air conditioners
• Sold only in standard packs
SOURCE 1 PART NO.
MANUFACTURER
MODEL NUMBER
SIZE
STD. PACK
MLP $
S1-52634349001
LAU
60-3795-02
7 DIA. X 5/8 SHAFT
10
11.96
*Sol d by Standard Pack / M LP per each
Bearings
LAU-PAK SEALED TYPE SLEEVE BEARINGS
Features:
• Self-aligning
• Durable construction
• Includes insulator
• Porous bronze sleeve
• Includes factory packed lubricant
• Sold in pairs
SOURCE 1 PART NO.
MODEL NO.
SHAFT DIA.
MLP $
S1-52634394001
S1-52634395001
S1-52634396001
38-2443-01
38-2443-02
38-2443-03
.625
.750
1.000
38.75
52.36
49.93
*Sol d in pairs / MLP per pair
200
Bearings
CARTRIDGE TYPE SLEEVE BEARINGS
Features:
• Bronze bushing, steel bearing caps
• Easy to interchange
• Neoprene conductive rubber cushion
• Includes factory packed lubricant
• Sold in pairs
SOURCE 1 PART NO.
MODEL NO.
SHAFT DIA.
INCLUDES
MLP $
S1-52634391001
38-2091-01
.750
THRUST COLLAR AND SPACER
57.07
*Sold in pai rs / MLP per pair
DIVERSITECH CUSHIONED PILLOW BLOCKS
SOURCE 1 PART NO.
DESCRIPTION
INDUSTRY NO.
LAU NO.
S1-535-BB1
S1-535-BB2
S1-535-BB3
S1-535-BB4
BRONZE BEARING PILLOW BLOCK
NAH8A
NAH10A
NAH12A
NAH16A
––
38-2204-01
38-2086-01
38-2087-01
BEARING SHAFT
SIZE
1/2”
5/8”
3/4”
1”
MLP $
11.04
12.11
13.64
13.86
DIVERSITECH SIDE FLANGE MOUNT PILLOW BLOCKS
SOURCE 1 PART NO.
DESCRIPTION
INDUSTRY NO.
BEARING SHAFT SIZE
MLP $
S1-535-BB5
S1-535-BB6
CUSHIONED FLANGE BLOCK
CUSHIONED FLANGE BLOCK
NVH12A
NVH10A
3/4”
5/8”
26.50
23.11
SEALED TYPE BALL BEARINGS
Features:
• Furnished with seals to avoid contaminants
• Includes insulator and interlocking thrust collar
• Prelubricated in factory
• Sold in pairs
SOURCE 1 PART NO.
MODEL NO.
SHAFT DIA.
MLP $
S1-52634397001
S1-52634398001
38-2588-01
38-2590-01
.750
1.000
124.32
134.86
*Sol d in pairs / MLP per pair
ADAPTER BUSHINGS (STEEL SHAFT)
Features:
• Zinc finish
• Sold only in standard packs
DIMENSIONS
SOURCE 1 PART NO.
MODEL NO.
O.D.
I.D.
LENGTH
STD. PACK
USED WITH
MLP $
S1-52634374000
027502-03
1.000
3/4
1-1/8
1
“A SERIES”
WHEELS
23.04
201
Bearings
VPB SERIES
Features:
• Normal duty two-bolt pillow block
• Shaft diameter 2-3/16"
SOURCE 1 PART NO.
IND. STD.
SHAFT DIA.
MLP $
S1-02924422000
S1-02924423000
VPB-235
VPB-239AH
2.4375
2.1875
532.18
646.21
Mounting Brackets
MOTOR MOUNT – FLEX BRACKET
Torsion Flex Bracket holds motor securely. Fits 5-1/2” motors. Typically used for Goodman equipment.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-DMB-3
5-1/2” MOTOR MOUNT TORSION FLEX BRACKET
42.79
MOTORS BRACKET
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-DMB-1
S1-DMB-2
FIXED LUG ASSEMBLY FOR 5-1/2” DIAMETER MOTORS
ADJUSTABLE LUG ASSEMBLY FOR 5-1/2” DIAMETER MOTORS
27.25
19.00
RHEEM MOTOR BRACKET
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-A60306K
MOUNTING PLATE FOR USE ON RHEEM CONDENSING UNITS
19.00
A.O. SMITH FLEXIMOUNT ADAPTER
Adapt standard frame m otor to Fleximount. Each adapter includes 3 gromm ets and 3 steel ferrules.
SOURCE 1 PART NO.
PART NO.
FRAME SIZE
MLP $
S1-02427878000
S1-02432032000
619432-174
619432-192
48
42
24.68
21.11
202
Mounting Brackets
BELT DRIVE BLOWER BEARING BRACKET
Features:
• Mounting hardware included
• Instructions included
• Must be ordered in standard pack
Knock Down Bracket Kit. For Easier Installation. Accommodates bearings that have 1-3/16" O.D.
SOURCE 1 PART NO.
MODEL NO.
O.D. SIZE
STD. PACK
MLP $
S1-52634381001
38-2699-01
1-13/16"
(2) SETS
41.71
203
Sheaves
AL/YB SERIES
Single Groove Sheaves for “4L” or “A” Belts
Features:
• Machined cast iron construction
• Equipped with hollow head set screws
• Light duty, no keyseat
• Do not use “A” cogged belt ratings with these sheaves
DIAMETERS
SOURCE 1 PART
NO.
S1-02804255700
S1-02807838700
S1-02810407700
S1-02810428700
S1-02812359700
INDUSTRY
STANDARD
SHEAVE NO.
YB5004
AL94X1
AL114X3/4
AL74X1
AL64X1
O.D.
BORE
PITCH
(P.D.)
KEYSEAT
5.93
8.93
10.93
6.93
5.93
.75
1
.75
1.0
1.0
5.78
8.78
10.78
6.78
5.78
Y
N
N
N
N
DIM. T WEIGHT
LBS.
1.06
1.06
1.06
1.06
1.06
1.2
2.35
3.1
1.5
1.2
MLP $
42.32
105.68
58.14
32.36
66.04
2MVP SERIES
Two Groove Sheaves for “A” & “B” Belts
Features:
• Machined cast iron construction
• Furnished with standard keyseats and 2 hollow head set screws
• Dynamically balanced
SOURCE 1 PART NO.
S1-02812369700
S1-02813931000
INDUSTRY STANDARD
SHEAVE NO.
2MVP60B74P
2MVP35B49
NO OF
GROOVES
2
2
O.D.
R.D.
OL
7.68
5.18
5.38
3.31
4.75
3.63
204
DATUM RANGE DATUM RANGE BORE DIA.
“A” BELT
“B” BELT
5.9-7.0
6.0-7.4
3.4 - 4.5
3.5 - 4.9
1-3/8
WT. (LBS.)
MLP $
29.3
9.8
1577.86
1221.86
Sheaves
AK SERIES
Single Groove Sheaves for “4L”, “A” or “3L” Belts
Features:
• Painted, machined cast iron construction
• Statically balanced
• Furnished with standard keyseats
• Furnished with hollow head set screws
SOURCE 1 PART NO.
S1-02807216700
S1-02808158700
S1-02808255700
S1-02809570700
S1-02809985700
S1-02812363700
S1-02812383700
S1-02812384700
S1-02812388700
S1-02812765700
S1-02812767700
S1-02814878000
INDUSTRY STANDARD
SHEAVE NO.
AK134X1
AK104X1-3/16
AK94X1-3/16
AK59X1
AK66X1
AK56X1
AK61X1
AK54X1
AK39X1
AK74X1
AK84X1
AK56H
O.D.
BORE
5.45
10.25
9.25
5.75
6.45
5.45
5.95
5.25
3.75
7.25
8.25
5.45
1
1.188
1.19
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1
PITCH (P.D.) “A” / “4L” BELT
10.00
5.50
6.20
5.20
5.70
5.00
3.50
7.00
8.00
PITCH (P.D.) “3L”
BELT
4.86
9.66
8.66
5.16
5.86
4.86
5.36
4.66
3.16
6.66
7.66
4.86
DIM. T
1.53
1.22
1.22
1.22
1.22
1.22
1.22
1.53
1.53
KEYSEAT
1/4" x 1/8"
1/4" x 1/8"
1/4" x 1/8"
1/4" x 1/8"
1/4" x 1/8"
1/4" x 1/8"
1/4" x 1/8"
1/4" x 1/8"
1/4" x 1/8"
1/4" x 1/8"
1/4" x 1/8"
1/4" x 1/8"
FIG.
3
3
3
3
3
3
2
3
3
WEIGHT
LBS.
7.5
5.1
4.5
2.0
2.3
1.9
2.1
1.8
1.4
3.4
3.8
MLP $
65.79
82.07
125.86
32.36
56.14
102.71
49.86
38.57
16.46
116.29
95.54
62.61
2AK SERIES
Two Groove Sheaves for “4L” or “A” Belts
Features:
• Furnished with hollow head screws
DIAMETERS
SOURCE 1 PART NO.
S1-02808256700
S1-02808257700
INDUSTRY STANDARD
SHEAVE NO.
2AK94X1-3/16
2AK114X1-3/16
O.D.
BORE
9.25
11.25
1.188
1.188
PITCH (P.D.) “A” / “4L”
BELT
9.00
11.00
205
PITCH (P.D.) “3L”
BELT
8.66
10.66
KEYSEAT
DIM. T
WEIGHT LBS.
MLP $
1/4 x 1/8
1/4 x 1/8
1.719
1.719
7.3
9.0
189.54
220.14
Sheaves
BK SERIES
Single Groove Sheaves for “4L”, “A”, “5L” & “B” Belts
Features:
SOURCE 1 PART NO.
S1-02804869700
S1-02807220700
S1-02807222700
S1-02810564700
S1-02810577700
S1-02812012700
S1-02812026700
S1-02812364700
S1-02815473000
S1-02815474000
INDUSTRY STANDARD
SHEAVE NO.
BK115X1
BK85X1
BK95X1
BK80X1
BK120X1-3/16
BK110X1-3/16
BK90X1
BK67X1
BK62H
BK57H
O.D.
BORE
11.25
8.25
9.25
7.75
11.75
10.75
8.75
6.45
5.95
5.45
1
1.000
1.000
1.000
1.188
1.188
1.000
1.000
PITCH (P.D.) “4L” / “A” BELT PITCH (P.D.) “5L” / “B”
BELT
7.50
8.50
7.00
11.00
10.00
8.00
5.70
7.90
8.90
7.40
11.40
10.40
8.40
6.10
DIM. T
WEIGHT LBS.
MLP $
1.53
1.53
1.53
1.53
1.53
1.53
1.28
5.0
5.4
4.4
7.4
6.4
5.0
2.8
2.4
2.3
144.14
107.64
111.71
76.36
120.00
101.75
184.18
67.61
77.46
28.21
2BK SERIES
Two Groove Sheaves for “4L” or “A” & “5L” or “B” Belts
Features:
DIAMETERS
SOURCE 1 PART NO.
S1-02805419700
S1-02805459700
S1-02808346000
S1-02809992700
INDUSTRY STANDARD
SHEAVE NO.
2BK70X1
2BK80X1
2BK130H
2BK100X1-7/16
O.D.
BORE
6.75
7.75
12.75
9.75
1.000
1.000
1.5
1.438
PITCH (P.D.) “A” / “4L”
BELT
6.00
7.00
12.2
9.00
206
PITCH (P.D.) “5L” /
“B” BELT
6.40
7.40
12.7
9.40
KEYSEAT
DIM. T
WEIGHT LBS.
MLP $
1/4 x 1/8
1/4 x 1/8
1/4 x 1/8
3/8 x 3/16
2.094
2.094
1.75
2.094
6.6
7.2
15.85
9.4
205.71
70.57
312.11
145.29
Sheaves
2BKH SERIES
Two Groove Sheaves for “4L” or “A” & “5L” or “B” Belts
Features:
• Furnished with special keys to fit standard keyseats
• Requires “H” split taper bushings
DIAMETERS
SOURCE 1 PART NO.
S1-02812368700
INDUSTRY STANDARD
SHEAVE NO.
2BK110H
O.D.
10.75
PITCH (P.D.) “4L” / “A”
BELT
10.00
DIM. T
PITCH (P.D.) “5L” / “B”
BELT
10.40
1.750
BUSHING
REQ’D.
H
WEIGHT LBS.
MLP $
9.3
107.18
BKH SERIES
Single Groove Sheaves for “4L” or “A” & “5L” or “B” Belts
Features:
• Furnished with special keys to fit standard keyseats
• Requires “H” split taper bushings
DIAMETERS
SOURCE 1 PART NO.
S1-02812773700
INDUSTRY STANDARD
SHEAVE NO.
BK80H
O.D.
7.75
PITCH (P.D.) “4L” / “A” BELT PITCH (P.D.) “5L” / “B”
BELT
7.00
7.40
BUSHING
REQ’D
H
DIM. T
WEIGHT LBS.
MLP $
1.56
3.4
98.79
TB SERIES
Two Groove Gripbelt Sheaves with Split Taper Bushings
for use w ith all “A” & “B” Section Belts
Features:
DIAMETERS
SOURCE 1 PART NO.
S1-02808525900
INDUSTRY STANDARD
SHEAVE NO.
2TB110
O.D.
11.35
PITCH (P.D.) “A” PITCH (P.D.) “B” BUSHING REQ’D
BELT
BELT
10.80
10.80
Q1
207
DIM. T
WEIGHT LBS.
MLP $
2.83
19.45
302.89
Sheaves
TC SERIES
DIAMETERS
SOURCE 1 PART NO.
S1-02808736700
S1-02808769700
INDUSTRY STANDARD
SHEAVE NO.
2TC72
2TC106
O.D.
7.60
11.00
BUSHING
REQ’D.
Q1
Q1
PITCH (P.D.)
“A” BELT
N/A
N/A
PITCH (P.D.)
“B” BELT
N/A
N/A
PITCH (P.D.)
“C” BELTS
7.60
11
DIM. O.L.
3.08
3.08
WEIGHT (LBS.)
LESS BUSHING
15.24
21.7
MLP $
450.14
730.43
B5V SERIES
Features:
• For use with “A”, “B” & “5V” belts
• Requires “B” split taper bushing
DIAMETERS
SOURCE 1 PART NO.
S1-02812070700
S1-02812307700
S1-02812308700
S1-02813269000
S1-02813270000
S1-02813271000
S1-02813272000
S1-02813358000
S1-02813359000
S1-02815946000
INDUSTRY STANDARD
SHEAVE NO.
2B5V58
2B5V124
2B5V68
2B5V50
2B5V52
2B5V60
2B5V64
2B5V46
2B5V54
2B5V40
O.D.
6.08
12.68
7.08
5.28
5.48
6.28
6.68
4.88
5.68
BUSHING
REQ’D.
B
B
B
B
B
B
B
B
B
PITCH (P.D.)
“A” BELT
5.4
12.0
6.4
4.6
4.8
5.6
6.0
4.2
5.0
208
PITCH (P.D.)
“B” BELT
5.8
12.4
6.8
5.0
5.2
6.0
6.4
4.6
5.4
PITCH (P.D.)
“5V” BELTS
5.9
12.5
6.9
5.1
5.3
6.1
6.5
4.7
5.5
DIM. T
FIG.
2.48
2.48
2.48
2.48
2.48
2.48
2.48
2.48
2.48
3
4
4
3
3
3
3
3
3
WEIGHT (LBS.)
LESS BUSHING
7.4
17.1
10.2
4.6
5.3
8.2
8.4
3.3
6.0
MLP $
202.29
346.71
221.18
178.07
184.11
208.32
274.71
206.82
135.07
191.96
Sheaves
TB SERIES
Three Groove Gripbelt Sheaves with Split Taper Bushings
for use w ith all “A” & “B” Section Belts
Features:
DIAMETERS
SOURCE 1 PART NO.
S1-02812061700
INDUSTRY STANDARD
SHEAVE NO.
3TB56
O.D.
5.95
PITCH (P.D.) “A” PITCH (P.D.) “B” BUSHING REQ’D
BELT
BELT
5.20
5.60
P1
DIM. T
WEIGHT LBS.
MLP $
2.750
9.0
91.86
1VP SERIES
Single Groove Variable Pitch Sheaves for “3L”, “4L”,“5L”, “A”, “B”, & “5V” Belts
Features:
• Painted, machined cast iron or steel construction
• Vibration free operation
DIAMETERS
SOURCE 1 PART NO.
INDUSTRY STANDARD SHEAVE NO.
O.D.
BORE DIA.
FIG.
DIM. T
WT. LBS.
MLP $
S1-02804761700
S1-02804763700
S1-02804765700
S1-02806405700
S1-02806434700
S1-02810436701
1VP56X1-1/8
1VP56X7/8
1VP62X1-1/8
1VP50X5/8
1VP40X5/8
1VP34X1/2
5.35
5.35
5.95
4.75
3.75
3.15
1.125
.875
1.125
0.625
.625
0.5
2
2
2
1
1
1
1.88
1.88
2.21875
1.94
1.88
1.88
4.4
4.4
6.1
1.9
1.9
1.2
125.36
128.36
157.04
29.11
61.00
56.87
S1-02810855700
S1-02812010700
S1-02812365700
S1-02812403700
S1-02812774700
S1-02812775700
S1-02812776700
S1-02812777700
S1-02804807700
1VP62X7/8
1VP68X1-3/8
1VP50X1-1/8
1VP75X1-3/8
1VP34X7/8
1VP44X7/8
1VP44X1-1/8
1VP60X1-1/8
1VP50X7/8
5.95
6.55
4.75
7.50
3.15
4.15
4.15
6.00
4.75
.875
1.375
1.125
1.375
.875
.875
1.125
1.125
0.875
2
2
2
2
1
2
2
2
2
2.21875
1.91
1.88
1.66
1.88
1.88
1.88
1.66
1.88
6.1
7.3
3.6
8.9
1.4
2.9
2.9
6.5
4.0
183.50
163.39
95.32
173.14
60.21
91.29
91.29
181.14
75.93
209
Sheaves
1VP SERIES
Single Groove Variable Pitch Sheaves for “3L”, “4L”,“5L”, “A”, “B”, & “5V” Belts
SOURCE 1
PART NO.
S1-02812774700
S1-02806434700
S1-02812775700
S1-02812776700
S1-02812365700
S1-02804763700
S1-02804761700
S1-02810855700
S1-02804765700
S1-02812777700
S1-02812010700
S1-02812778700
S1-02812403700
S1-02804807700
DIAMETERS
PITCH (P.D.)
“4L” OR “A” BELTS
“5L” OR “B” BELTS
“3L” BELTS
“5V” BELTS
MIN. TURNS MAX TURNS MIN. TURNS MAX TURNS MIN. TURNS MAX TURNS MIN. TURNS MAX TURNS
PITCH OPEN PITCH OPEN PITCH OPEN PITCH OPEN PITCH OPEN PITCH OPEN PITCH OPEN PITCH OPEN
1.7
2.3
2.7
2.7
3.3
3.9
3.9
———5.1
——3.3
4
4
4
4
4
4
4
———4
——4
2.5
3.1
3.5
3.5
4.1
4.7
4.7
———5.9
——4.1
0
0
0
0
0
0
0
———0
——0
1.9
2.4
2.8
2.8
3.4
4.0
4.0
4.4
4.4
4.2
5.2
5.3
5.7
3.4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
2.9
3.4
3.8
3.8
4.4
5.0
5.0
5.4
5.4
5.2
6.2
6.3
6.7
4.4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
2.4
2.7
3.1
3.1
3.7
4.3
4.3
4.7
4.7
4.3
5.5
5.4
5.8
3.7
5
6
6
6
6
6
6
6
6
6
6
6
6
6
3.2
3.7
4.1
4.1
4.7
5.3
5.3
5.9
5.9
5.5
6.5
6.6
7.0
4.7
1
1
1
1
1
1
1
0
0
0
1
0
0
7
———————4.7
4.7
—5.9
5.8
6.2
———————6
6
—6
6
6
———————5.9
6.9
—6.9
7.0
7.4
———————0
0
—1
0
0
2VP SERIES
Two Groove Variable Pitch Sheaves for “3L”, “4L”, “5L”, “A”, “B”, & “5V” Belts
Features:
• Vibration free operation
DIAMETERS
SOURCE 1 PART NO.
O.D.
BORE
KEYSEAT
DIM. T
FIG.
WT. LBS.
MLP $
S1-02804762700
S1-02805447700
S1-02807229700
S1-02808757700
S1-02808828700
S1-02809351700
S1-02809993700
2VP56X1-1/8
2VP62X1-3/8
2VP68X1-3/8
2VP75X1-3/8
2VP60X1-3/8
2VP62X1-1/8
2VP75X1-5/8
5.35
5.95
6.55
7.50
6.00
5.95
7.50
1.125
1.375
1.375
1.375
1.375
1.125
1.625
1/4 x 1/8
5/16 x 5/32
5/16 x 5/32
5/16 x 5/32
5/16 x 5/32
1/4 x 1/8
3/8 x 3/16
3.000
3.000
3.000
3.250
3.250
3.000
3.750
5
5
5
5
5
5
5
6.6
10.5
12.3
16.5
10.2
10.5
16.3
384.54
251.68
278.57
483.61
255.36
217.21
462.54
S1-02812780700
2VP71X1-5/8
7.10
1.625
3/8 x 3/16
3.750
5
14.4
312.32
210
Sheaves
2VP SERIES
Two Groove Variable Pitch Sheaves for “3L”, “4L”, “5L”, “A”, “B”, & “5V” Belts
DIAMETERS
PITCH (P.D.)
“3L” BELTS
SOURCE 1
PART NO.
“5V” BELTS
MIN. TURNS MAX TURNS MIN. TURNS MAX TURNS MIN. TURNS MAX TURNS MIN. TURNS MAX TURNS
PITCH OPEN PITCH OPEN PITCH OPEN PITCH OPEN PITCH OPEN PITCH OPEN PITCH OPEN PITCH OPEN
S1-02804762700
S1-02808828700
S1-02809351700
S1-02805447700
S1-02807229700
S1-02812780700
S1-02808757700
S1-02809993700
3.9
—
—
—
—
—
—
—
4
—
—
—
—
—
—
—
4.7
—
—
—
—
—
—
—
0
—
—
—
—
—
—
—
4.0
4.2
4.2
4.2
4.8
5.3
5.7
5.7
5
5
5
5
5
5
5
5
5.0
5.2
5.2
5.2
5.8
6.3
6.7
6.7
0
0
0
0
0
0
0
0
4.3
4.3
4.5
4.5
5.1
5.4
5.8
5.8
6
6
6
6
6
6
6
6
5.3
5.5
5.5
5.5
6.1
6.6
7.0
7.0
1
0
0
0
0
0
0
0
—
—
4.9
4.9
5.5
5.8
6.2
6.2
—
—
6
6
6
6
6
6
—
—
5.9
5.9
6.5
7.0
7.4
7.4
VL, VM SERIES
Single Groove Variable Pitch Sheaves for use with “3L”, “4L”, “5L”, “A” & “B” Belts
Features:
• Do not use “VL” & “VM” sheaves with gripnotch belts
DIAMETERS
SOURCE 1 PART NO.
O.D.
BORE
FIG.
WT. LBS.
MLP $
S1-02804764700
S1-02804807700
S1-02806564700
S1-02812361700
S1-02812385700
S1-02812781700
1VL44X7/8
1VM50X7/8
1VL44X5/8
1VL40X5/8
1VL40X7/8
1VL34X1/2
4.15
4.75
4.15
3.75
3.75
3.15
.875
.875
.625
.625
.875
.500
1
1
1
1
1
1
1.9
1.9
1.9
1.7
1.7
1.2
56.50
75.93
65.79
97.89
31.00
60.21
DIAMETERS
PITCH (P.D.)
“3L” BELTS
SOURCE 1
PART NO.
S1-02812781700
S1-02812361700
S1-02812385700
S1-02806564700
S1-02804764700
S1-02804807700
MIN. TURNS
PITCH OPEN
1.7
2.3
2.3
2.7
2.7
3.3
4
4
4
4
4
4
MAX TURNS MIN. TURNS MAX
PITCH OPEN PITCH OPEN PITCH
2.5
3.1
3.1
3.5
3.5
4.1
0
0
0
0
0
0
1.9
2.4
2.4
2.8
2.8
3.4
5
5
5
5
5
5
211
2.9
3.4
3.8
3.8
4.4
5.0
TURNS MIN.
OPEN PITCH
0
0
0
0
0
0
2.4
2.7
2.7
3.1
3.1
3.7
TURNS MAX
OPEN PITCH
5
6
6
6
6
6
3.2
3.7
3.7
4.1
4.1
4.7
TURNS
OPEN
1
1
1
1
1
1
—
—
0
0
0
0
0
0
Bushings
SPLIT TAPER BUSHINGS
Features:
M alleable iron, furnished with standard keyseat and hollow head set screw
DIMENSIONS
SOURCE 1 PART NO.
S1-02808617700
S1-02812064700
S1-02812082700
S1-02812306700
S1-02812338700
S1-02812374700
S1-02812785700
S1-02814752000
INDUSTRY STANDARD BORE
SHEAVE NO.
H X 1-3/16
P1 X 1-5/8
B X 1-5/8
B X 2-7/16
B X 2-3/16
H X 1-7/16
P1 X 1-1/8
H X 1-3/8
1.188
1.625
1.625
2.438
2.188
1.438
1.125
1.375
O.D.
T
“D” LG.
END
2.500
3.000
3.687
3.687
3.687
2.500
3.000
2.500
1.250
1.937
1.937
1.937
1.937
1.250
1.937
1.250
1.625
1.937
2.625
2.625
2.625
1.625
1.937
1.625
“D” SM. KEYSEAT
NO. OF
CAPSCREWS
END
CAPSCREWS
SIZE
1.570
1.855
2.557
2.557
2.557
1.570
1.855
1.570
1/4 x 1/8
3/8 x 3/16
3/8 x 3/16
5/8 x 5/16
1/2 x 1/4
3/8 x 3/16
1/4 x 1/8
5/16 x 5/32
2
3
3
3
3
2
3
2
1/4 x 3/4
5/16 x 1
5/16 x 1-1/4
5/16 x 1-1/4
5/16 x 1-1/4
1/4 x 3/4
5/16 x 1
1/4 x 3/4
WRENCH
TORQUE IN
LBS.
95
192
192
192
192
95
192
95
FIG.
WEIGHT
LBS.
MLP $
1
4
3
4
4
2
3
1
.8
1.3
1.8
1.8
1.8
.8
1.3
.8
25.14
34.17
40.13
40.13
40.13
20.50
36.43
25.18
Source 1 V-Belts
ACCU-LINK ADJUSTABLE V-BELTS
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-3L-LINK-5
S1-A-LINK-25
S1-A-LINK-5
S1-B-LINK-6
BELT,DRIVE,3L,ACCU-LINK,5 FOOT
BELT,DRIVE,A,ACCU-LINK,25 FOOT
BELT,DRIVE,A,ACCU-LINK,5 FOOT
BELT,DRIVE,B,ACCU-LINK,6 FOOT
82.68
332.71
86.29
120.64
212
MULTI-PLUS V-BELTS
New dual belt brand on MULTI-PLUS belts clearly identifies both RMA classical part
number and dimensionally equivalent FHP number. MULTI-PLUS allows consolidation of
existing classical and FHP belt sizes into a single line that will handle both drive
applications thus reducing inventory.
Dimensions: width x thickness.
Optimum blends of synthetic rubbers combined with a unique cord treating process re sults
in a belt able to serve a dual purpose while offering more versatility and value.
SOURCE 1 PART NO.
INDUSTRY STANDARD BELT NO.
OUTSIDE LENGTH (INCHES)
MLP $
S1-A15
S1-A16
S1-A17
S1-A18
S1-A19
S1-A20
S1-A21
S1-A22
S1-A23
S1-A24
S1-A25
S1-A26
S1-A27
S1-A28
S1-A29
S1-A30
S1-A31
S1-A32
S1-A33
S1-A34
S1-A35
S1-A36
S1-A37
S1-A38
S1-A39
S1-A40
S1-A41
S1-A42
S1-A43
S1-A44
S1-A45
S1-A46
S1-A47
S1-A48
S1-A49
S1-A50
S1-A51
S1-A52
A15/4L170
A16/4L180
A17/4L190
A18/4L200
A19/4L210
A20/4L220
A21/4L230
A22/4L240
A23/4L250
A24/4L260
A25/4L270
A26/4L280
A27/4L290
A28/4L300
A29/4L310
A30/4L320
A31/4L330
A32/4L340
A33/4L350
A34/4L360
A35/4L370
A36/4L380
A37/4L390
A38/4L400
A39/4L410
A40/4L420
A41/4L430
A42/4L440
A43/4L450
A44/4L460
A45/4L470
A46/4L480
A47/4L490
A48/4L500
A49/4L510
A50/4L520
A51/4L530
A52/4L540
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
5.61
5.61
5.61
5.61
5.68
5.68
5.75
5.75
5.82
5.86
5.89
5.89
6.00
6.11
6.21
6.36
6.36
6.43
6.57
6.68
6.82
6.82
6.82
7.25
7.54
7.57
7.61
7.71
7.93
8.00
8.07
8.18
8.29
8.39
8.46
8.54
8.61
8.68
S1-A53
S1-A54
S1-A55
S1-A56
S1-A57
S1-A58
S1-A59
S1-A60
S1-A61
S1-A62
A53/4L550
A54/4L560
A55/4L570
A56/4L580
A57/4L590
A58/4L600
A59/4L610
A60/4L620
A61/4L630
A62/4L640
55
56
57
58
59
60
61
62
63
64
8.86
9.07
9.07
9.29
9.36
9.39
9.43
9.54
9.68
9.75
S1-A63
S1-A64
S1-A65
S1-A66
S1-A67
S1-A68
S1-A69
S1-A70
S1-A71
A63/4L650
A64/4L660
A65/4L670
A66/4L680
A67/4L690
A68/4L700
A69/4L710
A70/4L720
A71/4L730
65
66
67
68
69
70
71
72
73
9.96
10.11
9.86
9.86
10.00
10.43
10.50
10.89
10.93
213
SOURCE 1 PART NO.
MLP $
S1-A72
S1-A73
S1-A74
S1-A75
S1-A76
S1-A77
S1-A78
S1-A79
S1-A80
S1-A81
S1-A82
S1-A83
S1-A84
S1-A85
S1-A86
S1-A87
S1-A88
S1-A89
S1-A90
S1-A91
S1-A92
S1-A93
S1-A94
S1-A95
A72/4L740
A73/4L750
A74/4L760
A75/4L770
A76/4L780
A77/4L790
A78/4L800
A79/4L810
A80/4L820
A81/4L830
A82/4L840
A83/4L850
A84/4L860
A85/4L870
A86/4L880
A87/4L890
A88/4L900
A89/4L910
A90/4L920
A91/4L930
A92/4L940
A93/4L950
A94/4L960
A95/4L970
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
10.64
10.71
10.79
10.96
11.14
11.61
11.79
11.57
12.25
12.00
12.14
12.36
12.46
12.68
12.86
13.04
13.18
13.89
13.57
13.75
13.86
14.50
14.14
14.29
S1-A96
S1-A97
S1-A98
S1-B21
S1-B22
S1-B23
S1-B24
S1-B25
S1-B26
S1-B27
S1-B28
S1-B29
S1-B30
S1-B31
S1-B32
S1-B33
S1-B34
S1-B35
S1-B36
S1-B37
S1-B38
S1-B39
S1-B40
S1-B41
S1-B42
S1-B43
S1-B44
A96/4L980
A97/4L990
A98/4L1000
B21/5L240
B22/5L250
B23/5L260
B24/5L270
B25/5L280
B26/5L290
B27/5L300
B28/5L310
B29/5L320
B30/5L330
B31/5L340
B32/5L350
B33/5L360
B34/5L370
B35/5L380
B36/5L390
B37/5L400
B38/5L410
B39/5L420
B40/5L430
B41/5L440
B42/5L450
B43/5L460
B44/5L470
98
99
100
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
14.43
14.57
14.75
6.64
7.43
7.93
8.18
8.14
8.25
8.29
8.32
8.39
8.43
8.54
8.57
9.04
8.71
9.07
9.29
9.75
9.68
9.96
10.39
10.07
10.89
11.04
11.04
S1-B45
S1-B46
S1-B47
S1-B48
S1-B49
S1-B50
S1-B51
S1-B52
S1-B53
S1-B54
S1-B55
S1-B56
S1-B57
S1-B58
S1-B59
S1-B60
S1-B61
S1-B62
B45/5L480
B46/5L490
B47/5L500
B48/5L510
B49/5L520
B50/5L530
B51/5L540
B52/5L550
B53/5L560
B54/5L570
B55/5L580
B56/5L590
B57/5L600
B58/5L610
B59/5L620
B60/5L630
B61/5L640
B62/5L650
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
11.36
11.79
11.86
12.25
12.32
12.46
12.71
12.75
12.93
13.07
13.14
13.25
13.29
13.32
13.57
13.14
13.82
14.07
S1-B63
S1-B64
S1-B65
S1-B66
S1-B67
S1-B68
S1-B69
B63/5L660
B64/5L670
B65/5L680
B66/5L690
B67/5L700
B68/5L710
B69/5L720
66
67
68
69
70
71
72
13.64
13.75
14.32
14.68
14.29
14.46
15.61
214
Source 1 V-Belts
MULTI-PLUS V-BELTS
SOURCE 1 PART NO.
MLP $
S1-B70
S1-B71
S1-B72
S1-B73
S1-B74
S1-B75
S1-B76
S1-B77
S1-B78
S1-B79
S1-B80
S1-B81
S1-B82
S1-B83
S1-B84
S1-B85
S1-B86
S1-B87
S1-B88
S1-B89
S1-B90
S1-B91
S1-B92
S1-B93
S1-B94
S1-B95
S1-B96
S1-B97
B70/5L730
B71/5L740
B72/5L750
B73/5L760
B74/5L770
B75/5L780
B76/5L790
B77/5L800
B78/5L810
B79/5L820
B80/5L830
B81/5L840
B82/5L850
B83/5L860
B84/5L870
B85/5L880
B86/5L890
B87/5L900
B88/5L910
B89/5L920
B90/5L930
B91/5L940
B92/5L950
B93/5L960
B94/5L970
B95/5L980
B96/5L990
B97/5L1000
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
15.89
15.43
15.54
16.18
16.29
16.32
16.11
16.39
16.43
17.29
17.54
17.07
17.29
18.29
18.36
17.93
18.11
18.32
18.50
18.61
18.79
19.00
19.14
19.32
20.29
20.46
20.64
20.57
215
MULTI-COGGED V-BELTS
Features:
• Raw edge, cogged construction
• More horsepower in less space
• Notches are molded extra deep
• Oil and heat resistant
SOURCE 1 PART NO.
INDUSTRY BELT NO.
MLP $
S1-AX22
S1-AX23
S1-AX24
S1-AX25
S1-AX26
S1-AX27
S1-AX28
S1-AX29
S1-AX30
S1-AX31
S1-AX32
S1-AX33
S1-AX34
S1-AX35
S1-AX36
S1-AX37
S1-AX38
S1-AX39
S1-AX40
S1-AX41
S1-AX42
S1-AX43
S1-AX44
S1-AX45
S1-AX46
S1-AX47
S1-AX48
S1-AX49
S1-AX50
S1-AX51
S1-AX52
S1-AX53
S1-AX54
S1-AX55
S1-AX56
S1-AX57
S1-AX58
S1-AX59
AX22
AX23
AX24
AX25
AX26
AX27
AX28
AX29
AX30
AX31
AX32
AX33
AX34
AX35
AX36
AX37
AX38
AX39
AX40
AX41
AX42
AX43
AX44
AX45
AX46
AX47
AX48
AX49
AX50
AX51
AX52
AX53
AX54
AX55
AX56
AX57
AX58
AX59
10.54
10.54
10.54
10.54
10.54
10.54
10.54
10.96
11.25
11.79
11.61
11.82
12.00
12.64
12.43
12.79
13.50
13.50
13.50
13.75
14.00
14.75
14.96
14.50
15.18
15.50
14.96
15.29
15.86
15.46
15.57
15.75
16.00
16.21
16.36
16.61
16.64
16.82
S1-AX60
S1-AX61
S1-AX62
S1-AX63
S1-AX64
S1-AX65
S1-AX66
S1-AX67
S1-AX68
S1-AX69
AX60
AX61
AX62
AX63
AX64
AX65
AX66
AX67
AX68
AX69
17.07
17.46
17.46
17.61
17.86
18.32
18.32
18.50
18.71
19.46
S1-AX70
S1-AX71
S1-AX72
S1-AX73
S1-AX75
S1-AX76
S1-AX78
S1-AX80
S1-AX84
AX70
AX71
AX72
AX73
AX75
AX76
AX78
AX80
AX84
19.50
19.68
19.93
19.96
20.32
20.54
21.29
21.96
23.36
216
SOURCE 1 PART NO.
INDUSTRY BELT NO.
MLP $
S1-AX85
S1-AX86
S1-AX90
S1-AX92
S1-AX96
S1-BX100
S1-BX103
S1-BX105
S1-BX108
S1-BX112
S1-BX113
S1-BX115
S1-BX116
S1-BX120
S1-BX124
S1-BX30
S1-BX31
S1-BX32
S1-BX33
S1-BX34
S1-BX35
S1-BX36
S1-BX37
S1-BX38
AX85
AX86
AX90
AX92
AX96
BX100
BX103
BX105
BX108
BX112
BX113
BX115
BX116
BX120
BX124
BX30
BX31
BX32
BX33
BX34
BX35
BX36
BX37
BX38
23.57
23.82
25.18
25.71
26.82
40.46
39.82
40.64
42.18
43.86
44.21
44.79
45.07
46.29
47.93
14.43
14.43
16.29
16.29
16.29
16.86
16.75
17.43
17.86
S1-BX39
S1-BX40
S1-BX41
S1-BX42
S1-BX43
S1-BX44
S1-BX45
S1-BX46
S1-BX47
S1-BX48
S1-BX49
S1-BX50
S1-BX51
S1-BX52
S1-BX53
S1-BX54
S1-BX55
S1-BX56
S1-BX57
S1-BX58
S1-BX59
S1-BX60
S1-BX61
S1-BX62
S1-BX63
S1-BX64
S1-BX65
BX39
BX40
BX41
BX42
BX43
BX44
BX45
BX46
BX47
BX48
BX49
BX50
BX51
BX52
BX53
BX54
BX55
BX56
BX57
BX58
BX59
BX60
BX61
BX62
BX63
BX64
BX65
17.86
18.71
19.11
20.21
19.96
20.25
21.14
21.93
21.29
22.57
22.43
23.25
23.61
23.00
24.04
24.29
24.43
24.61
24.96
24.96
25.11
25.29
25.61
25.96
25.32
26.64
26.00
S1-BX66
S1-BX67
S1-BX68
S1-BX69
S1-BX70
S1-BX71
S1-BX72
S1-BX73
S1-BX74
S1-BX75
S1-BX76
S1-BX77
S1-BX78
S1-BX79
S1-BX80
S1-BX81
S1-BX82
S1-BX83
BX66
BX67
BX68
BX69
BX70
BX71
BX72
BX73
BX74
BX75
BX76
BX77
BX78
BX79
BX80
BX81
BX82
BX83
26.36
26.57
27.82
27.57
28.57
28.89
27.89
29.25
29.29
30.36
30.07
30.07
31.61
30.86
31.29
32.86
32.46
33.96
S1-BX84
S1-BX85
S1-BX86
S1-BX87
S1-BX88
S1-BX89
S1-BX90
BX84
BX85
BX86
BX87
BX88
BX89
BX90
33.32
34.57
34.96
36.25
34.14
35.82
36.25
217
Source 1 V-Belts
MULTI-COGGED V-BELTS
SOURCE 1 PART NO.
INDUSTRY BELT NO.
MLP $
S1-BX91
S1-BX92
S1-BX93
S1-BX94
S1-BX95
S1-BX96
S1-BX97
S1-BX98
S1-BX99
BX91
BX92
BX93
BX94
BX95
BX96
BX97
BX98
BX99
35.75
36.04
36.61
36.96
37.36
39.18
38.18
38.32
38.79
218
NARROW, COGGED, RAW EDGE, DEEP WEDGE V-BELTS
Features:
• Raw edge, cogged construction increases power transmission
• Oil & heat resistant
• Dissipates static
SOURCE 1 PART NO.
INDUSTRY BELT NO.
MLP $
S1-3VX1000
S1-3VX1060
S1-3VX1120
S1-3VX1180
S1-3VX1250
S1-3VX1320
S1-3VX1400
S1-3VX250
S1-3VX265
S1-3VX280
S1-3VX290
S1-3VX300
S1-3VX315
S1-3VX335
S1-3VX355
S1-3VX375
S1-3VX390
S1-3VX400
S1-3VX425
S1-3VX450
S1-3VX475
S1-3VX500
S1-3VX530
S1-3VX560
S1-3VX600
S1-3VX630
S1-3VX670
S1-3VX710
S1-3VX750
S1-3VX800
S1-3VX850
S1-3VX900
S1-3VX950
S1-5VX1000
S1-5VX1030
S1-5VX1060
S1-5VX1080
S1-5VX1120
3VX1000
3VX1060
3VX1120
3VX1180
3VX1250
3VX1320
3VX1400
3VX250
3VX265
3VX280
3VX290
3VX300
3VX315
3VX335
3VX355
3VX375
3VX390
3VX400
3VX425
3VX450
3VX475
3VX500
3VX530
3VX560
3VX600
3VX630
3VX670
3VX710
3VX750
3VX800
3VX850
3VX900
3VX950
5VX1000
5VX1030
5VX1060
5VX1080
5VX1120
100
106
112
118
125
132
140
25
26.5
28
29
30
31.5
33.5
35.5
37.5
39
40
42.5
45
47.5
50
53
56
60
63
67
71
75
80
85
90
95
100
103
106
108
112
28.18
29.79
32.39
34.50
36.89
39.00
41.36
10.29
10.54
10.86
11.11
11.11
11.57
11.86
12.39
12.68
13.43
13.43
13.96
14.54
15.04
15.29
15.79
16.36
17.14
17.64
18.43
19.50
20.50
21.89
23.50
25.29
26.61
64.79
68.71
68.71
75.39
72.68
S1-5VX1150
S1-5VX1180
S1-5VX1230
S1-5VX1250
S1-5VX1320
S1-5VX1400
S1-5VX1500
S1-5VX1600
S1-5VX1700
S1-5VX1800
5VX1150
5VX1180
5VX1230
5VX1250
5VX1320
5VX1400
5VX1500
5VX1600
5VX1700
5VX1800
115
118
123
125
132
140
150
160
170
180
74.71
79.50
81.36
84.43
85.86
90.57
97.39
104.00
114.75
117.46
S1-5VX1900
S1-5VX2000
S1-5VX450
S1-5VX470
S1-5VX490
S1-5VX500
S1-5VX510
S1-5VX530
S1-5VX540
5VX1900
5VX2000
5VX450
5VX470
5VX490
5VX500
5VX510
5VX530
5VX540
190
200
45
47
47
50
51
53
54
124.29
131.14
32.39
33.61
32.39
33.61
33.71
34.96
35.29
219
Source 1 V-Belts
NARROW, COGGED, RAW EDGE, DEEP WEDGE V-BELTS
SOURCE 1 PART NO.
INDUSTRY BELT NO.
MLP $
S1-5VX550
S1-5VX560
S1-5VX570
S1-5VX580
S1-5VX590
S1-5VX600
S1-5VX610
S1-5VX630
S1-5VX650
S1-5VX660
S1-5VX670
S1-5VX680
S1-5VX690
S1-5VX710
S1-5VX730
S1-5VX740
S1-5VX750
S1-5VX780
S1-5VX800
S1-5VX810
S1-5VX825
S1-5VX830
S1-5VX840
S1-5VX850
S1-5VX860
S1-5VX880
S1-5VX900
S1-5VX950
S1-5VX960
5VX550
5VX560
5VX570
5VX580
5VX590
5VX600
5VX610
5VX630
5VX650
5VX660
5VX670
5VX680
5VX690
5VX710
5VX730
5VX740
5VX750
5VX780
5VX800
5VX810
5VX825
5VX830
5VX840
5VX850
5VX860
5VX880
5VX900
5VX950
5VX960
55
56
57
58
59
60
61
63
65
66
67
68
69
71
73
74
75
78
80
81
82.5
83
84
85
86
88
90
95
96
35.29
35.29
39.61
38.14
38.14
38.14
40.04
40.00
44.25
42.64
42.64
47.00
47.00
47.00
47.93
47.93
47.93
51.11
53.00
55.04
53.96
55.04
57.11
57.11
59.29
57.14
57.14
61.39
61.39
220
—NOTES—
221
—NOTES—
222
—NOTES—
223
—NOTES—
224
CONDENSATE PUMPS & ACCESSORIES
Source 1 Condensate Pumps
Source 1 condensate pumps provide great features at a value price. Suitable for use with condensate from high efficiency condensing
furnaces and boilers which produce acidic condensate. 20 ft. of lift. Features include vibration dampening feet and motor mounts,
metal hang tabs, four inlet holes, a clear indicator display, a float switch and removeable check valve, and a pan pill dispenser.
Integrating a Source 1 condensate pump into your system is easy, using 1/4-inch quick connect terminals that provide easy
connection to the built-in overflow switch. Three terminals are provided, allowing flexibility to connect air-handler shut-down and
optional alarm as needed. Suitable for use with condensate up to 160°F.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-CP20
S1-CP20T
CONDENSATE PUMP, 20’ LIFT, 120V, WITH SAFETY SWITCH
CONDENSATE PUMP, 20’ LIFT, 120V, WITH SAFETY SWITCH &
TUBING
REPLACEMENT CHECK VALVE FOR CP-SERIES CONDS PUMPS
6
6
94.46
99.82
S1-CP-CV
6.39
DiversiTech Clear-Vue Condensate Pumps
No Float, No Problems! ClearVue’s iQ Technology™ and Floatless Sensor™ make this the most advanced condensate pump ever. This new pump can
provide up to 22’ of lift if needed. ClearVue™ runs at the minimum speed needed, saving wear on the pump. The pump selects the lowest effective speed,
making it quieter than a regular pump. Its unique self-cleaning feature senses problems and automatically enters a self-cleaning mode using condensate water
to fix the issue. The ClearVue™ pump features a clear bottom tank to easily check the water level. Other features include: stainless steel mounting tabs,
silicone rubber feet, reversible deck, four inlet holes, and LED indicator lights.
SOURCE 1 PART NO.
DESCRIPTION
ORDER MULTIPLE
MLP $
S1-IQP-120
S1-IQP-120T
CLEARVUE PUMP, 120V, 0-22' LIFT
CLEARVUE PUMP, 120V, 0-22' LIFT, W/TUBING
6
6
145.46
154.43
DiversiTech Condensate Pumps
Suitable for use with condensate from high efficiency condensing furnaces and boilers which produce acidic condensate. 22’ of lift
compared to the typical 20’. Features include vibration dampening feet and motor mounts, metal hang tabs, four inlet holes, a clear
indicator display, a float switch and check valve, and pan pill dispenser. Integrating the CP-22 into your system is easy. 1/4” inch quick
connect terminals provide easy connection to the built in overflow switch. 3 terminals are provided allowing flexibility to connect airhandler shut-down and optional alarm as needed. The new CP-22LP comes packed with all the same great features found in the CP22, but now in a low profile package. This pump is only 4-3/8” tall so it’s a good fit for those instances where space is at a premium.
The shorter reservoir holds 1/3 gallon. Suitable for use with condensate up to 160ºF.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-CP-22
S1-CP-22-230
S1-CP-22-230T
S1-CP-22LP
S1-CP-22LP-230
S1-CP-22T
S1-CP-CV
CONDENSATE PUMP – 120V
CONDENSATE PUMP – 230V
CONDENSATE PUMP – 230V W/20’ 3/8” TUBE
CONDENSATE PUMP – 120V – LOW PROFILE
CONDENSATE PUMP – 2300V – LOW PROFILE
CONDENSATE PUMP – 120V W/20’ 3/8” TUBE
REPLACEMENT CHECK VALVE FOR CP-SERIES CONDS
PUMPS
6
6
6
6
6
6
99.68
120.93
125.11
114.54
125.00
105.04
6.39
*Sol d by pack / MLP per each
DiversiTech A/C Condensate Float Switch
Designed for use in condensate drain pan overflow. Easily installed on the side of the auxiliary drain pan. Single pole,
double throw normally OPEN or normally CLOSED.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-JMP
CONDENSATE FLOAT SWITCH
21.32
225
DiversiTech Condensate CopTM
Condensate Cop is a unique clamp on float switch intended for HVAC drain pan installation. The Condensate Cop features a large
over clamping area that fits easily over the edge of all types of drain pans; including formed plastic and galvanized sheet metal. A
separate float/ probe assembly swivels to accommodate drain pans having sloped sides. The swivel action allows the installer to
position the float switch for best operation and then clamp it into place. The probe features an inlet grill which prevents the float from
being blocked or damaged by insulation or other debris. Sealed inside the probe is a magnetically actuated normally closed switch.
The switch opens when rising water presents a potential flooding condition. Two wire connection for easy hook up to a thermostat “Y”
(compressor) circuit. Provided complete with 5’ (1.5 meter) leads, wire nuts, and clamping screws. Small size, 24V/1.5 amp NC reed
switch.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-CC-1
CONDENSATE COPTM DRAIN PAN SWITCH
12
20.00
DiversiTech Condensate Detection Switches
DiversiTech CS1200 AC Shutoff Switch
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-CS1200
SWITCH,SHUTOFF,CONDENSATE DETECT,AC
12
25.39
DiversiTech Flow-PlusTM Pump Treatment Tablets for Condensate Pumps
A unique polymer pan treatment in tablet form for use exclusively in DiversiTech’s condensate pump. The tablet dispensing drawer in
the pump holds 3 tablets. A dosage lasts up to 3 months depending on the volume of condensate generated. Even when fully
dissolved, the tablets provide a lasting treatment in the pump and downstream drain line. Provides long-lasting treatment that controls
slime growth over time and can extend the life of the pump.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-SCM-186-6
FLOW-PLUSTM FOR CONDENSATE PUMPS - 6
36 CLAMSHELLS/CASE
17.25
TABLETS/CLAMSHELL
DiversiTech Safety Overflow Switch (SOS)
Designed for use on 3/4” PVC condensate drain line. Snaps easily over existing drain line tubing and can be glued in place using PVC
cement if desired. The SOS works by electronically sensing water near the inside wall of the PVC drain tubing. By locating the SOS
with its body away from the normal flow, it can be used to detect a possible overflow condition when the PVC drain line becomes full
with water. Like a culvert, the condensate drain line is normally mostly empty with a small amount of water flowing in the lower parts of
the horizontal run. Since the sensor component of the SOS only covers part of the tubing, a low volume of flowing water does not
activate the switch. The pipe must be full or near full to activate the switch. The SOS can be mounted horizontally, vertically, or at any
angle.
Works with 24 VAC control circuits and typical contactors. When not detecting water, the SOS is normally closed and allows normal
air conditioner operation. When water approaches the SOS’s sensor, the switch triggers, and the control circuit is opened. The LED
indicator lights to show that there may be system trouble, and the SOS is doing its job.
Furnished complete with switch, 5’ (1.5 meter) 18 AWG, 2 wire lead, and a 3/4” PVC male fitting adapter for direct coupling to a
primary pan drain line connection. Now available with Push to Test button .
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-SOS-1
SAFETY OVERFLOW SWITCH
64.64
226
DiversiTech Wet Switch Flood Detector
A solid state control designed to help prevent flooding, damage to carpets, walls, furniture, ceilings, etc. Now has a built-in test and
reset button for easier installation. Turns system off when detecting moisture due to condensate or drain leaks. One or two drops will
cause Wet Switch to turn off a unit, alerting a serviceman to a moisture problem. A lit LED indicates the Wet Switch is activated and
has turned the unit off. Re-set simply by drying the absorbent pad with a paper towel and pressing the reset switch. Connects to 24
VAC. More than one unit may be connected to a system. 2 amp contact rating. Simple 5 wire installation.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-WS-1
WET SWITCH FLOOD DETECTOR
89.32
Little Giant Pumps & Accessories
VCC Series Low Profile
Features:
• Low profile for limited space applications
• 1/30-HP motor
• ABS tank, motor cover, and volute
• 3/10-gal tank capacity
•
•
•
•
Stainless steel shaft
Removable 3/8" barbed check valve
T hermal overload protection
Safety switch
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-554210
COMPACT CONDENSATE PUMP 230 VOLT 50/60 HZ 1/30 HP WITH
SAFETY SWITCH/NO TUBING/6' CORD/80 GPH @ 1'/20' SHUTOFF
COMPACT CONDENSATE PUMP 115 VOLT 60 HZ 1/30 HP WITH
SAFETY SWITCH/NO TUBING/ 6’ CORD/80 GPH @ 1’/20’ SHUTOFF
196.57
S1-VCC-20ULS 115V
162.46
VCL Series
Little Giant VCL Series is ideal for collecting, detecting and the automatic removal of condensate from air
conditioning equipment, de-humidifiers, high efficiency furnaces, condensing boilers and other equipment where
an automatic drain pump is required.
Features:
• 1/5 HP motor
• Galvanized steel tank cover
• ABS tank, volute and switch cover
• 1 gallon tank capacity
• Stainless steel shaft
• Snap-action switch
• Safety switch
• Thermal overload protection
• 3/8" discharge copper tube
• UL / CSA listed
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-553240
VCL-45ULS AUTOMATIC CONDENSATE REMOVAL PUMP 115V 60
HZ 1/5 HP WITH SAFETY SWITCH FLOAT & STEM/6' CORD/450
GPH @ 1'/45' SHUTOFF
592.93
227
VCMA Series
Features:
• 1/50-HP high performance motor
• ABS tank, motor cover, and volute
• 1/2-gal tank capacity
• Stainless steel shaft
•
•
•
•
Snap-action switch
Removable 3/8" barbed check valve
3 drain inlet holes
Thermal overload protection
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-VCMA-15UL 115V
CONDENSATE PUMP 115 VOLT 60 HZ 1/50 HP NO SAFETY
SWITCH/NO TUBING / 6’ CORD/65 GPH@1’/15’ SHUT OFF
CONDENSATE PUMP 115 VOLT 60 HZ 1/50 HP WITH SAFETY
SWITCH/WITH TUBING / 6’ CORD/65 GPH@1’/15’ SHUT OFF
CONDENSATE PUMP 115 VOLT 60 HZ 1/30 HP NO SAFETY
98.93
S1-VCMA-15ULS 115V
S1-VCMA-15ULST 115
S1-VCMA-20UL 115V
S1-VCMA-20ULS 115V
S1-VCMA-20ULS 230V
S1-VCMA-20ULST 115
S1-VCMA-20ULST 230
105.50
113.36
121.50
114.71
137.93
125.39
140.68
VCMX Series
Features:
• 1/4-turn check valve allows servicing without removal of tubing, eliminating water spills
• Patend-pending cooling design increases pump life
• External test/run lever for quick and easy drainage of tank for servicing
• Oil resistant tank and check valve eliminates the problem of cracked tanks with exposure to oil
• Rubber feet absorb vibration on hard surface installations
• Slimmer footprint size offers flexibility in tight spaces
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-554530
VCMX-20ULS, 20' LIFT, 115V, WITH SAFETY SWITCH, WITHOUT
TUBING
VCMX-20ULST, 20' LIFT, 115V, WITH SAFETY SWITCH, WITH
TUBING
VCMX-20ULST, 20' LIFT, 115V, WITH SAFETY SWITCH, WITH
TUBING
127.00
S1-554531
S1-554550
134.61
133.32
EC Series
The EC-OP is easily mounted below the air conditioner on the right, left or in the middle. The kit takes up less
space than other pumps and includes all components necessary for installation.
Features:
• Pump enclosure
• Mounting bracket for easy wall mounting
• Installation template for positioning
• Clear reservoir for visual inspection
• Safety overflow circuit
• cCSAus
• Float retainer
• Multi-fit inlet adapter
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-553712
EC-OP-K AUTOMATIC CONDENSATE REMOVAL PUMP 230V 50
HZ
314.04
228
Electronic Condensate Removal Pumps
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-EC-400 115V
ELECTRONIC CONDENSATE REMOVAL PUMP 115 VOLT/60 HZ/4
GPH @ 1’/CURUS CERT
ELECTRONIC CONDENSATE REMOVAL PUMP 230 VOLT/50/60
HZ/4 GPH @ 1’/CURUS CERT
273.11
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ACS2
CONDENSATE OVERFLOW SAFETY SWITCH 72” LEADS/48
VOLTS AC/DC/UR/C-CSA
19.25
S1-EC-400 230V
229.39
Little Giant Pump Accessories
6 Series Submersible Sump Pump
Typical applications include commercial, industrial, and home uses where liquid must be transferred or
recirculated.
Features:
• 1/3 hp shaded pole motor with overload protection
• Designed for continuous duty
• Epoxy coated cast iron housing
• 1-1/4" (31.7 mm) adapter and 3/4" (19 mm) garden hose adapter available
• Carbon/ceramic shaft seal
• Upper and lower sintered sleeve bearings
• cCSAus listed
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-CIA
6 SERIES SUBMERSIBLE SUMP PUMP
392.39
Rectorseal Safe-T-Switch® Condensate Overflow Controls
Detects clogged air conditioner condensate drains and shuts off the system to prevent water damage to floors, walls, and ceilings. While A/C flooding can
result from other problems, clogged A/C drain pans are the most common cause of water damage and mold growth from air conditioners. Model SS3 is
designed to fit in either primary or auxiliary drain pans. All switches UL Listed 508.
SOURCE 1 PART NO.
APPLICATION
MLP $
S1-SS1
S1-SS2
S1-SS3
S1-SS3-CT
RECTORSEAL PRODUCT
NO.
97630
97635
97645
97652
INLINE
SECONDARY LINE
DRAIN PAN
NORMALLY OPEN. WORKS WITH COMMUNICATING
40.57
34.96
20.32
21.21
S1-SS4
97625
PLASTIC, SLANT-SIDE, OR LIPPED-EDGE DRAIN PANS
26.64
229
CONDENSATE DRAINING
A/C Secondary Condensate Drain Pans
Rolled edges for durability, ribbed bottoms for rigidity, and reinforced corners for strength. 3/4” PVC fittings are included with each
pan. No seams, no rust, and no leakage. ABS materials will not put out toxic smoke. Available in over 20 convenient sizes. Five pans
per clip. Complies with Southern Building Code. For air handler applications only.
BOTTOM DIMENSION
OVERALL DIMENSION
DEPTH
SOURCE 1 PART NO.
IN.
CM.
IN.
CM.
IN.
CM.
NO. CLIP
MLP $
S1-6-1246L
S1-6-1246S
S1-6-1838L
S1-6-1838S
S1-6-1846L
S1-6-1846S
S1-6-2424L
S1-6-2626L
12” x 46”
12” x 46”
18” x 38”
18” x 38”
18” x 46”
18” x 46”
24” x 24”
26” x 26”
30 x 117
30 x 117
46 x 97
46 x 97
46 x 117
46 x 117
61 x 61
66 x 66
14” x 48”
14” x 48”
20” x 40”
20” x 40”
20” x 48”
20” x 48”
26” x 26”
28” x 28”
36 x 122
36 x 122
51 x 102
51 x 102
51 x 122
51 x 122
66 x 66
71 x 71
2
2
2
2
2
2
2
2
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
34.50
34.54
36.21
36.21
37.11
37.11
34.96
37.11
S1-6-2739L
S1-6-2748L
S1-6-2748S
S1-6-2763L
S1-6-2763S
S1-6-3030L
S1-6-3050L
S1-6-3050S
S1-6-3060L
S1-6-3060S
S1-6-3263L
S1-6-3263S
S1-6-3636L
S1-6-3660L
S1-6-3660S
27” x 39”
27” x 48”
27” x 48”
27” x 63”
27” x 63”
30” x 30”
30” x 50”
30” x 50”
30” x 60”
30” x 60”
32” x 63”
32” x 63”
36” x 36”
36” x 60”
36” x 60”
69 x 99
69 x 122
69 x 122
69 x 160
69 x 160
76 x 76
76 x 127
76 x 127
76 x 152
76 x 152
81 x 160
81 x 160
91 x 91
91 x 152
91 x 152
29” x 41”
29” x 50”
29” x 50”
29” x 65”
29” x 65”
32” x 32”
32” x 52”
32” x 52”
32” x 62”
32” x 62”
34” x 65”
34” x 65”
38” x 38”
38” x 62”
38” x 62”
74 x 104
74 x 127
74 x 127
74 x 165
74 x 165
81 x 81
81 x 132
81 x 132
81 x 157
81 x 157
86 x 165
86 x 165
97 x 97
97 x 157
97 x 157
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
52.07
53.57
61.21
66.68
75.86
38.61
57.11
66.00
62.86
75.43
63.86
76.75
48.14
64.89
79.79
† Source 1 Part Num bers ending in L = Drain Line Outlets in Long Side Source 1 Part Num bers ending in S = Drain Line Outlets in Short Side
*Sold by clip / MLP per each
Condensate Drain Pans
When a mini split system operates in heat pump mode, the outdoor coil becomes the evaporator coil. Typically, condensation
generates from the evaporator coil. In certain installations, the condenser coil may be mounted overhead on brackets affixed to a wall.
In these overhead applications, dripping condensation may be a nuisance. Condensate drain pans bolt onto the condenser mounting
brackets, and the drain line can be plumbed to a nearby drain location. Furnished complete with all mounting hardware and drain pan
outlet, condensate drain pans are available in either plastic or powder coated steel.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-230-DPML
S1-230-DPMM
S1-230-DPPL
S1-230-DPPM
METAL CONDENSATE DRAIN PAN (LARGE)
METAL CONDENSATE DRAIN PAN (MEDIUM)
POLY CONDENSATE DRAIN PAN (LARGE)
POLY CONDENSATE DRAIN PAN (MEDIUM)
271.43
276.86
103.93
94.04
230
CONDENSATE DRAINING
DiversiTech High Rise PansTM
The High Rise PanT M is an innovative new plastic drain pan design which allows placement of an air handler
2-3/4” above the outside lip of the pan without the need for separate, cumbersome mounting blocks. The pan has a molded-in network
of risers to give a 5“ lift. The risers are positioned to accept a wide variety of air handler sizes. Each riser has a specially shaped area
at each end to accommodate a 2” x 2” anti-vibration pad which allows for quiet operation at all times. Other features include heavy
duty reinforcement throughout to give plenty of support as well as rolled edges for durability. Onepiece plastic construction ensures no
rust, leaks, or seams to split. Each High Rise PanT M comes complete with a Condensate CopT M float switch (S1-CC-1, page 227), 6
EVAT M anti-vibration pads (S1-MP-2E, page 235), and 1-3/4” PVC male adapter (S1-6-1, page 232). Installation is straightforward and
hassle-free.
SOURCE 1 PART NO.
S1-6-HK2748
S1-6-HK2766
S1-6-HK3050
S1-6-HK3060
S1-6-HK3060-1
DESCRIPTION
STD. PACK
MLP $
HIGH RISE PAN 27” X48” WITH INSTALLATION KIT INCLUDING:
ONE CC-1 CONDENSATE COP, SIX MP-2E 2” X 2” EVATM PADS, ONE
5
141.29
5
166.04
5
151.07
5
164.57
1
172.79
TM
6-1 3/4” PVC MALE ADAPTER
HIGH RISE PANTM 27” X 66” WITH INSTALLATION KIT INCLUDING:
ONE CC-1 CONDENSATE COP, SIX MP-2E 2” X 2” EVATM PADS ONE
HIGH RISE PANTM 30” x 60” WITH INSTALLATION KIT INCLUDING:
ONE CC-1 CONDENSATE COP, SIX MP-2E 2” x 2” EVATM PADS ONE
Metal Drain Pan
The ultimate in drain pan design — tailored for easy distribution and installation. Full of features to make life easier on both the
distributor and the contractor. Seamless metal construction with nestable rolled edges for maximum safety and integrity — a stack of
70 pans is only a foot high! Once on site, you’ll never have to return to the distributor for missing parts. T he fittings are packaged with
the pan for simple and efficient installation. Choose between two possible drain outlet positions and install with confidence
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-6-M2748
S1-6-M2763
S1-6-M3030
S1-6-M3050
S1-6-M3060
S1-6-M3263
26 GAUGE METAL DRAIN PAN – 27” x 48”
5
5
5
5
5
5
76.68
93.79
60.68
81.11
92.00
97.36
Charles Gallo Brand Drain Gun & Swoosh CO2 Cartridges
Clears condensate drains with a SWOOSH! A lightweight (3 oz.) portable tool designed to blow out drain lines
instantly. New larger SWOOSH CO2 cartridges now deliver 1200 PSI of oil-free food grade air to clear the line.
Each unit comes equipped with a tapered fitting to work on 3/8”–3/4” drain openings. Flexible hose assembly
maneuvers through cabinets, coils and hard to reach drains. Cartridges are environmentally safe and recyclable.
No need for air or nitrogen tanks. Reduces labor costs and time on service calls.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-GG-1
CHARLES GALLO DRAIN GUN FOR A/C CONDENSATE
LINES
CHARLES GALLO DRAIN GUN ADAPTER KIT
CHARLES GALLO DRAIN GUN HOSE ASSEMBLY
SWOOSH CO2 CARTRIDGES - 12 PER PACK/6 PACKS
6
91.89
1
1
6
31.11
12.75
57.71
S1-GG-1A
S1-GG-1H
S1-GGC-12
PER CASE
*Sol d by pack / MLP per each **M LP per pack
231
CONDENSATE DRAINING
A/C Condensate Drain Pan Fittings
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-6-1
S1-6-2
S1-6-3
S1-6-5
3/4” SLIP
1” SLIP
3/4” SLIP WITH PLASTIC NUT
3/4” FEMALE PIPE THREAD
50
50
50
50
3.21
5.29
6.07
3.61
*Sold by pack / M LP per each
EZ Trap Condensate Traps
EZT rap manufactures condensate traps for residential and light commercial applications. EZT rap is the leading expert in condensate traps as used in central
air conditioning systems and specializes in the manufacture of a full range of traps and components to suit any requirements.
All EZTrap condensate traps incorporate an innovative and patented see through feature and are designed for easy installation, easy inspection and easy
cleaning. In addition, EZTrap offers the only trap available which incorporates an integral float switch to warn of blockages in the trap itself or the condensate
line downstream. EZTrap also offers the unique and patented cross trap which permits the contractor to clean the outlet of the drain pan without access to the
inside of the Air Conditioning unit. All models are currently available in 3/4” and 1” sizes as standard.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-EZT113
S1-EZT113B
S1-EZT119
S1-EZT150
S1-EZT205
S1-EZT207
S1-EZT210
3/4" ECONOMY BLOWMOLD CROSS TRAP KIT, NO BRUSH
3/4" ECONOMY BLOWMOLD CROSS TRAP KIT, WITH BRUSH
1" STANDARD CROSS TRAP KIT
ULTRATRAP WATERLESS TRAP KIT
3/4" SPECIAL 3" DEEP CROSS TRAP KIT WITH INTEGRAL FLOAT SWITCH
3/4" SIDE ENTRY CROSS TRAP KIT FOR A COILS WITH INTEGRAL FLOAT SWITCH
3/4" STANDARD CROSS TRAP KIT WITH INTEGRAL FLOAT SWITCH
15.96
22.32
45.14
48.36
69.18
63.50
61.68
S1-EZT224
S1-EZT225
COMPACT OVERFLOW SWITCH, 2/4" MALT THREADED INLET
INLINE PRIMARY /SECONDARY OVERFLOWSWITCH, 3/4" AND 1”
28.18
29.93
S1-EZT226
S1-EZT228
28.18
54.32
S1-EZT406
COMPACT OVERFLOW SWITCH, 3/4" FEMALE SLIP INLET
INLINE PRIMARY/SECONDARY OVERFLOW SWITCH 3/4" WITH CLEAR EXTENSION,
SCREW-IN PLUG AND CABLE
FLEXIBLE BRUSH
S1-EZT626
TRAP/OVERFLOW COMBO PACK
45.64
5.39
Clear Vinyl Tubing
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CVT12100
S1-CVT14100
S1-CVT34100
S1-CVT38100
S1-CVT58100
S1-CVT78050
CLEAR VINYL TUBING, 1/2”ID x 100’
CLEAR VINYL TUBING, 5/8"ID x 100’
35.71
22.43
67.75
23.96
47.61
54.36
232
CONDENSATE DRAINING
Gorilla TubeTM Clear Vinyl Tubing
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-7-12P
S1-7-34P
S1-7-38P
S1-7-58P
1/2" I.D. x 100'
3/4" I.D. x 100'
3/8" I.D. x 100'
5/8" I.D. x 100'
65.86
110.57
40.32
80.82
233
GAS ACCESSORIES
B-Vent, Metal-Fab Style "M" Round
Style "M" Round B-Vent
Metal-Fab's round Type-B vent is listed by Underwriters Laboratories for use with approved category 1 gas furnaces, heaters, and
boilers. A category 1 appliance operates with a non-positive vent static pressure. The double wall design of B-vent enables the
product to be used in homes and commercial buildings at close clearance to combustible. Metal-Fab's B-vent design incorporates
features that make installation quick, easy, and safe.
Features:
• Elimination of sharp edges by hemming the flue and casing
• Assembly & disassembly, without tools, using positive twist lock
• 360 degree rotation of small diameter fittings using swivel tees, wyes, and elbows
SOURCE 1 PART NO.
ORDER MULTIPLE
DIAMETER (IN)
LENGTH (FT)
MLP $
S1-MF-3M12
S1-MF-3M12A
S1-MF-3M24
S1-MF-3M3
S1-MF-3M5
S1-MF-4M12
S1-MF-4M12A
S1-MF-4M24
S1-MF-4M3
S1-MF-4M5
S1-MF-5M12
S1-MF-5M12A
S1-MF-5M18
S1-MF-5M18A
S1-MF-5M24
S1-MF-5M3
S1-MF-5M4
S1-MF-5M5
S1-MF-5M6
S1-MF-5M6A
S1-MF-6M12
S1-MF-6M12A
S1-MF-6M18
S1-MF-6M18A
S1-MF-6M24
S1-MF-6M3
S1-MF-6M4
S1-MF-6M5
S1-MF-6M6
S1-MF-6M6A
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
3
3
3
3
3
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
1
1 (ADJ)
2
3
5
1
1 (ADJ)
2
3
5
1
1 (ADJ)
1.5
1.5 (ADJ)
2
3
4
5
0.5
0.5 (ADJ)
1
1 (ADJ)
1.5
1.5 (ADJ)
2
3
4
5
0.5
0.5 (ADJ)
14.61
18.82
22.86
30.71
46.43
17.61
20.93
27.21
36.00
55.71
21.04
25.00
24.93
29.79
32.25
42.46
55.14
66.18
18.68
22.25
22.96
27.36
29.14
35.50
38.18
49.00
64.14
76.39
19.07
25.75
234
GAS ACCESSORIES
B-Vent, Metal-Fab Style "M" Round
Style "M" Round B-Vent Accessories
SOURCE 1 PART NO.
DESCRIPTION
ORDER MULTIPLE
DIAMETER (IN)
MLP $
S1-MF-3M90
S1-MF-3MCHP
S1-MF-3MF
S1-MF-3MFT
S1-MF-3MSC
S1-MF-4M90
S1-MF-4MCHP
S1-MF-4MF
S1-MF-4MFT
S1-MF-4MSC
S1-MF-5M45/60
S1-MF-5M90
S1-MF-5MCHP
S1-MF-5MCUHP
S1-MF-5MF
S1-MF-5MF-12
S1-MF-5MSC
S1-MF-6M45/60
S1-MF-6M90
S1-MF-6MCHP
S1-MF-6MCUHP
S1-MF-6MF
S1-MF-6MF-12
S1-MF-6MSC
90 DEG ELBOW
VENT CAP HP
FLASHING STD
FLAT TALL CONE
STORM COLLAR
90 DEG ELBOW
VENT CAP HP
FLASHING STD
FLAT TALL CONE
STORM COLLAR
60 DEG ELBOW
90 DEG ELBOW
VENT CAP HP
VENT CAP UNV
FLASHING STD
FLASHING 12/12 PITCH
STORM COLLAR
60 DEG ELBOW
90 DEG ELBOW
VENT CAP HP
VENT CAP UNV
FLASHING STD
FLASHING 12/12 PITCH
STORM COLLAR
6
12
12
6
24
6
12
12
6
24
6
6
12
8
12
6
24
6
6
12
12
12
6
24
3
3
3
3
3
4
4
4
4
4
5
5
5
5
5
5
5
6
6
6
6
6
6
6
39.43
21.00
16.11
25.79
4.21
46.64
23.57
18.32
28.93
4.25
32.86
55.61
32.50
33.46
25.07
49.71
9.25
40.71
66.68
41.82
42.61
35.43
9.86
9.86
Chimney Liner Kits
Continental Industries FlexJet Chimney Liner
FlexJet replaces rigid gas vent components with more versatile, flexible segments. The product is appropriate for use wherever
double-wall, Type B gas vent is required. Using these segments can greatly simplify installation by allowing an offset between rigid
sections of pipe.
Features:
•
•
•
•
Durable double-wall, air-insulated construction
Snap-Lock male and female ends
UL listed as a connection between an appliance and Type B gas vent or as a segment of the Type B gas vent
Safe for use in conditioned or unconditioned spaces
SOURCE 1 PART NO.
DESCRIPTION
DIAMETER (IN)
LENGTH (FT)
MLP $
S1-3FSK25
S1-3FSK35
S1-4FSK35
S1-5FSK25
S1-5FSK35
LINER KIT,CHIMNEY STD FLEX JET 3INX25FT
3
3
4
5
5
25
35
35
25
35
124.68
148.25
161.32
161.46
188.89
S1-6FSK25
S1-6FSK35
6
6
25
35
204.86
239.14
Condensing Furnace Concentric Vent Terminal Kits
The S1-1CT0302 and S1-1CT0303 concentric vent cap accessories are approved for application with UPG condensing furnaces.
Each kit consist s of a top cap, inner and outer flues, and a 45-degree mating connector. Kits with part numbers ending in “-636” are
ULC-636 certified, to comply with Canadian regulatory requirements.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-1CT0302
S1-1CT0302-636
S1-1CT0303
S1-1CT0303-636
2-INCH CONCENTRIC VENT TERMINAL KIT
2-INCH CONCENTRIC VENT TERMINAL KIT, ULC-363
3-INCH CONCENTRIC VENT TERMINAL KIT
3-INCH CONCENTRIC VENT TERMINAL KIT, ULC-636
67.86
89.29
95.32
112.50
235
GAS ACCESSORIES
Condensing Furnace Horizontal Vent Terminal Kits
Approved for use with UPG condensing furnaces. Each kit contains a vent base, vent cap, and four 2" screws. These kits are only for
use with sidewall venting of condensing furnaces. Kits with part numbers ending in "-636" are ULS-636 certified, to comply with
Canadian regulatory requirements.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-1HT0901
S1-1HT0902
3" HORIZONTAL VENT KIT
2" HORIZONTAL VENT KIT
36.39
33.93
DiversiTech Gas Ball Valve
Gas Ball Valves meet the stringent ISO 9000 quality standard. AGA and CGA certified.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-91-2032
S1-91-3042
S1-92-3232
S1-92-4242
1/2” O.D. FLARE x 1/2” FIP (FOR “20 SERIES” GAS CONN.)
5/8” O.D. FLARE x 3/4” FIP (FOR “30 SERIES” GAS CONN.)
1/2” FIP x 1/2” FIP
3/4” FIP x 3/4” FIP
10
10
10
10
17.43
24.43
9.82
15.50
*S ol d by pack / MLP per each
Gas Ball Valves (FIP x FIP)
Features:
• 175 WOG
• Lever handle
• Threaded ends
• Forged brass body
• CSA
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-GV12
S1-GV34
VLV, BALL, NAT GAS, 1/2 x 1/2 (M10)
VLV, BALL, NAT GAS, 3/4 x 3/4 (M10)
8.57
12.46
Dormont Manufacturing Co. Flexible Gas Connectors
Features:
• Annealed, 304 stainless steel (ASTM A240) flexible tubing
• Approved for indoor and outdoor use
• Temperature rating with adapters: –40° to 150°F
• Temperature rating with valves: –40° to 125°F
• 100% Factory leak tested
SOURCE 1 PART NO.
OUTSIDE DIAMETER (INCHES) INSIDE DIAMETER (INCHES)
LENGTH (INCHES)
MLP $
S1-20-3132-18
S1-20-3132-24
S1-20-3132-36
S1-20-3132-48
S1-30-3131-12
S1-30-3131-18
S1-30-3131-24
S1-30-3131-36
S1-30-3131-48
S1-30-3131-60
S1-30-3132-12
S1-30-3132-18
S1-30-3132-24
S1-30-3132-36
1/2
1/2
1/2
1/2
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
3/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
18
24
36
48
12
18
24
36
48
60
12
18
24
36
15.04
15.82
20.43
23.36
16.75
19.04
21.71
24.61
27.21
30.50
16.75
19.04
21.71
24.61
S1-30-3132-48
S1-30-3132-60
5/8
5/8
1/2
1/2
48
60
27.21
30.50
With Valve
SOURCE 1 PART NO.
OUTSIDE DIAMETER (INCHES)
INSIDE DIAMETER (INCHES)
LENGTH (INCHES)
MLP $
S1-20-3135-18
S1-20-3135-24
S1-20-3135-36
S1-20-3135-48
1/2
1/2
1/2
1/2
3/8
3/8
3/8
3/8
18
24
36
48
25.00
26.50
31.07
32.46
236
GAS ACCESSORIES
Yellow Coated Flexible Gas Connectors
T his durable, corrosion-resistant yellow coated stainless steel gas connector is configured with pipe threaded fittings for installation.
CSA approved.
SOURCE 1 PART NO.
OUTSIDE
INSIDE
LENGTH (INCHES)
MLP $
S1-30C-3131-24
S1-30C-3131-36
S1-30C-3131-48
S1-30C-3132-24
S1-30C-3132-36
S1-30C-3132-48
5/8
5/8
5/8
5/8
5/8
5/8
1/2
1/2
1/2
1/2
1/2
1/2
24
36
48
24
36
48
24.14
27.04
29.68
24.18
27.04
29.68
GRILLES AND REGISTERS
MV Series Ceiling Diffusers
Airtec's Model MV ceiling diffuser line is a snap to install in any ceiling. Quick tear off bands allow for easy size
changes and our swinging clips will fasten the assembly into the ceiling in seconds! Made from high impact
polymers and featuring a virtually airtight damper for winter shut off and/or volume control makes them a great fit
in any application.
Specifications:
• Duct Sizes - 6" 7" 8"
• Strap Included
• Integral Damper
• Max. Ceiling Thickness - 1.25"
• Required Hole Diameter - 9.25"
SOURCE 1 PART NO.
DESCRIPTION
AK FACTOR
MLP $
S1-MV3
S1-MV360
S1-MV4
CEILING DIFFUSER WITH 3-WAY GRILLE
CEILING DIFFUSER WITH ROUND GRILLE
CEILING DIFFUSER WITH 4-WAY GRILLE
0.29
0.33
0.30
42.32
42.32
42.32
GRILLES, REGISTERS, AND DIFFUSERS
Grilles
Continental Industries Grilles
Features:
•
•
•
•
•
•
•
Aluminum Construction
1/2" Spaced Fins
Lanced Face
White Finish
Ceiling and Sidewall Applications
One Piece Standard Face
Heads of Mounting Screws are Painted
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-AFBG60W1412
S1-AFBG60W3012
S1-AFBG60W3036
S1-G25W1406
S1-G25W3006
S1-G25W3008
GRILLE,ALUM,60 DEG DEF,14X12,WHITE
GRILLE,RETURN 14X6,WHITE
10
3
1
20
10
10
75.39
128.46
473.68
5.86
11.07
14.54
237
GRILLES, REGISTERS, AND DIFFUSERS
Registers
Continental Industries Registers
Features:
•
•
•
•
•
Steel Construction
Opposed Blade
Rolled Face
Golden Brown or White Finish
Reinforced for Strength
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-22W1004
S1-22W1204
S1-22W1206
S1-28B0410
S1-28B0412
S1-28W0410
S1-28W0412
S1-AVMW1206
REGISTER,SIDEWALL,2 WAY,10X4,WHITE
REGISTER,FLOOR,4X10,BROWN
REGISTER,FLOOR,4X12,BROWN
REGISTER,FLOOR,4X10,WHITE
REGISTER,FLOOR,4X12,WHITE
REGISTER,ADJ,WALL/CEILING,12X6,WHITE
24
24
24
24
24
24
24
24
8.43
9.39
11.07
6.00
8.07
6.00
8.07
49.29
238
MOUNTING ACCESSORIES
Carson Ecopad
Features:
• Lightweight—80% lighter than pre-cast concrete
• NO concrete forming or finishing
• NO heavy equipment, NO clean-up, NO hassles
• Solid wall construction won’t chip or crack
• Accepts bolts and screws for easy anchoring
• Chemical resistant
• UV stable, impervious to sunlight
Suitable for application in extremely hot or cold temperatures
SOURCE 1 PART NO.
MFR. PART NO.
LENGTH
WIDTH
THICKNESS
MLP $
S1-1836-2
S1-2424-2
S1-2424-3
S1-2436-2
S1-2436-3
S1-2448-3
S1-3030-2
S1-3030-3
S1-3036-3
S1-3040-2
S1-3333-2
S1-3333-3
S1-3338-2
S1-3345-2
S1-3345-3
S1-3348-2
S1-3636-2
S1-3636-3
S1-3642-2
S1-3642-3
S1-3648-2
S1-3648-3
S1-5042-3
S1-5042-3
S1-5050-3
S1-5060-3
S1-5070-3
92120001
92120002
93120021
92120003
93120022
93120004
92120007
93120006
93120007
92120009
92120011
93120010
92120012
92120013
93120012
92120014
92120015
93120014
92120016
93120015
92120017
93120016
93120017
93120017
93120018
93120019
93120020
18
24
24
24
24
24
30
30
30
30
33
33
33
33
33
33
36
36
36
36
36
36
50
50
50
50
50
36
24
24
36
36
48
30
30
36
40
33
33
38
45
45
48
36
36
42
42
48
48
42
42
50
60
70
2
2
3
2
3
3
2
3
3
2
2
3
2
2
3
2
2
3
2
3
2
3
3
3
3
3
3
37.54
37.54
43.71
52.66
58.54
70.43
48.18
61.18
71.50
57.36
54.89
62.46
58.93
70.96
83.36
82.93
63.54
76.04
76.21
100.64
91.46
99.61
144.96
144.96
198.64
212.07
317.36
239
Carson Plastic Duragrid Condenser Pads
SOURCE 1 PART NO.
LENGTH
WIDTH
HEIGHT
PALLET QUANTITY
MLP $
S1-ACP1836-2
S1-ACP2424-2
S1-ACP2424-3
S1-ACP2436-2
S1-ACP2436-3
S1-ACP3024-2
S1-ACP3030-2
S1-ACP3030-3
S1-ACP3036-2
S1-ACP3036-3
S1-ACP3040-2
18
24
24
24
24
30
30
30
30
30
30
36
24
24
36
36
24
30
30
36
36
40
2
2
3
2
3
2
2
3
2
3
2
50
50
32
50
32
50
25
16
25
16
25
52.96
46.32
58.61
63.86
83.43
61.75
68.89
87.25
81.39
99.14
83.14
S1-ACP3040-3
S1-ACP3333-2
S1-ACP3333-3
S1-ACP3338-2
S1-ACP3338-3
S1-ACP3345-2
S1-ACP3345-3
S1-ACP3636-2
S1-ACP3636-3
S1-ACP3642-2
S1-ACP3648-2
S1-ACP3648-3
S1-ACP5050-3
S1-ACP5060-3
S1-ACP5070-3
30
33
33
33
33
33
33
36
36
36
36
36
50
50
50
40
33
33
38
38
45
45
36
36
42
48
48
50
60
70
3
2
3
2
3
2
3
2
3
2
2
3
3
3
3
16
25
16
25
16
25
16
25
16
25
25
16
16
16
16
102.29
75.29
91.04
86.18
111.75
107.21
125.82
85.46
111.32
115.04
123.00
148.18
234.21
295.82
373.68
240
DiversiTech Elite® Plastic Equipment Pads
E Lite’s rugged design provides uniform and generous ribbing for optimum, self-leveling ground support without inserts. The result is a
pad that is lightweight, but not too light. A subtle texture prevents unit slide and presents a classic appearance, which is enhanced by
rounded edges and a concrete gray color. Each pad is molded with a size label and a symbol representing content of recycled
material.
SOURCE 1 PART NO.
LENGTH
WIDTH
THICKNESS
PALLET QUANTITY
MLP $
S1-EL1838-3
S1-EL2424-2
S1-EL2424-3
S1-EL2430-2
S1-EL2436-2
S1-EL2436-3
S1-EL2626-2
S1-EL3030-2
S1-EL3030-3
S1-EL3036-2
S1-EL3040-2
S1-EL3040-3
S1-EL3232-2
S1-EL3232-3
S1-EL3238-2
S1-EL3244-2
S1-EL3244-3
S1-EL3434-2
S1-EL3434-3
S1-EL3636-2
S1-EL3636-3
S1-EL3640-2
S1-EL3640-3
S1-EL3648-2
S1-EL3648-3
S1-EL3842-2
S1-EL3842-3
S1-EL3870-3
S1-EL4040-3
S1-EL4558-3
S1-EL4848-3
S1-EL4872-3
S1-EL5252-3
S1-EL5658-3
18
24
24
24
24
18
26
30
30
30
30
30
32
32
32
32
32
34
34
36
36
36
36
36
36
38
18
38
40
45
48
48
52
56
38
24
24
30
36
38
26
30
30
36
40
40
32
32
38
44
44
34
34
36
36
40
40
48
48
42
38
70
40
58
48
72
52
58
3
2
3
2
2
3
2
2
3
2
2
3
2
3
2
2
3
2
3
2
3
2
3
2
3
2
3
3
3
3
3
3
3
3
16
44
16
22
22
16
22
22
16
22
22
16
22
16
22
22
16
22
22
22
16
22
16
22
16
22
16
16
16
16
16
8
16
16
51.04
34.36
37.07
44.79
56.36
73.82
44.93
53.86
67.25
83.89
93.18
76.36
64.54
83.89
96.07
110.93
123.89
94.61
82.86
76.64
79.71
95.21
104.39
134.25
107.21
121.11
142.54
256.00
115.61
263.43
234.29
345.32
223.82
319.04
241
DiversiTech The Black Pad®
An innovative equipment Base, The Black Pad uses ground, recycled rubber in a co-injection process. The pad is extremely durable,
resistant to ultraviolet light, and heavier than a completely plastic pad. The Black Pad is suitable for use with pool pump, filters, and
heaters and complies with the 1997 Standard Swimming Pool Code sections 305.2 Mounting and section 405 Equipment
Foundations and Enclosures.
Features:
• No cracking and less breakage than concrete
• Extremely durable, yet lightweight
• UV resistant; unaffected by weather
• Generous ribbing for optimum, self-leveling ground support
• Textured surface prevents equipment slippage
• Drillable for securing equipment
• Made of recycled material
SOURCE 1 PART NO.
DESCRIPTION
LENGTH
WIDTH
THICKNESS
MLP $
S1-BP2424-2
S1-BP2424-3
S1-BP2436-2
S1-BP2436-3
S1-BP2838-3
S1-BP3030-2
S1-BP3030-3
S1-BP3036-3
S1-BP3232-2
S1-BP3232-3
S1-BP3244-2
S1-BP3244-3
S1-BP3636-2
S1-BP3636-3
S1-BP3648-3
S1-BP3842-2
S1-BP4040-3
S1-BP4550-3
S1-BP5252-3
BLACK EQUIPMENT PAD
BLACK EQUIPMENT PAD
BLACK EQUIPMENT PAD
BLACK EQUIPMENT PAD
BLACK EQUIPMENT PAD
BLACK EQUIPMENT PAD
BLACK EQUIPMENT PAD
BLACK EQUIPMENT PAD
BLACK EQUIPMENT PAD
BLACK EQUIPMENT PAD
BLACK EQUIPMENT PAD
BLACK EQUIPMENT PAD
BLACK EQUIPMENT PAD
BLACK EQUIPMENT PAD
BLACK EQUIPMENT PAD
BLACK EQUIPMENT PAD
BLACK EQUIPMENT PAD
BLACK EQUIPMENT PAD
BLACK EQUIPMENT PAD
24
24
24
24
28
30
30
30
32
32
32
32
36
36
36
38
40
45
52
24
24
36
36
28
30
30
36
32
32
44
44
36
36
48
42
40
50
52
2
3
2
3
3
2
3
3
2
3
2
3
2
3
3
2
3
3
3
40.32
51.46
63.93
61.00
61.61
61.18
68.43
87.14
70.64
86.43
101.82
105.89
85.75
93.25
148.21
114.75
135.50
228.61
237.82
242
DiversiTech UltraLite® Lightweight Equipment Pads
A true concrete equipment pad at the weight of plastic (about 2.5 lbs. per square foot). UltraLite® is strengthened by miles of fiber in
each square foot of fiber-cement coating. This fiber allows the pad to flex instead of cracking or breaking. The extured surface
prevents the condensing unit or portable generator from sliding, and allows water drainage, while the engineered encapsulated
polystyrene (EPS) core prevents warping and provides a solid bottom to resist settling. Unaffected by soil conditions, ultraviolet (UV)
light, temperature extremes, and other weather conditions.
SOURCE 1 PART NO.
LENGTH
WIDTH
THICKNESS
PALLET QTY.
MLP $
S1-U3678-3
S1-U4848-3
S1-U5056-3
S1-U5252-3
S1-UC1636-2
S1-UC1636-3
S1-UC2424-2
S1-UC2424-3
S1-UC2430-2
S1-UC2430-3
S1-UC2436-2
S1-UC2436-3
S1-UC2442-3
S1-UC2448-2
S1-UC2448-3
S1-UC2626-2
S1-UC2626-3
S1-UC2628-2
S1-UC3030-2
S1-UC3030-3
S1-UC3036-2
S1-UC3040-2
S1-UC3040-3
S1-UC3048-3
S1-UC3143-2
S1-UC3232-2
S1-UC3232-3
S1-UC3234-2
S1-UC3237-2
S1-UC3237-3
S1-UC3434-2
S1-UC3434-3
S1-UC3445-2
S1-UC3445-3
S1-UC3636-2
S1-UC3636-3
S1-UC3640-2
36
48
50
52
16
16
24
24
24
24
24
24
24
24
24
26
26
26
30
30
30
30
30
30
31
32
32
32
32
32
34
34
34
34
36
36
36
78
48
56
52
36
36
24
24
30
30
36
36
42
48
48
26
26
28
30
30
36
40
40
48
43
32
32
34
37
37
34
34
45
45
36
36
40
3
3
3
3
2
3
2
3
2
3
2
3
3
2
3
2
3
2
2
3
2
2
3
3
2
2
3
2
2
3
2
3
2
3
2
3
2
15
15
15
15
20
15
20
15
20
15
20
15
15
20
15
20
15
20
20
15
20
20
15
15
15
20
15
20
20
15
20
15
20
15
20
15
20
226.82
194.75
202.04
228.25
33.61
39.93
30.96
38.61
40.86
66.21
56.79
57.89
70.68
76.64
75.79
46.39
46.64
50.11
51.11
61.04
70.93
63.61
88.89
103.79
93.61
57.04
68.18
77.07
78.96
79.43
78.96
87.00
105.86
114.93
73.11
88.82
78.54
S1-UC3642-3
36
42
3
15
101.39
S1-UC3648-2
S1-UC3648-3
S1-UC3842-2
S1-UC3842-3
S1-UC4040-2
S1-UC4040-3
S1-UC4042-3
S1-UC4347-3
36
36
38
38
40
40
40
43
48
48
42
42
40
40
42
47
2
3
2
3
2
3
3
3
20
15
20
15
20
15
15
15
117.18
107.64
111.54
122.86
112.11
137.18
111.54
160.21
243
DiversiTech UltraLite® Earthquake Code Compliant Pads
Required nearly exclusively in Southern California, the UltraLite pad is available for compliance with strict attachment provisions
detailed in earthquake-prone local building codes. UltraLite earthquake code compliant pads are only available for sale in regions
where local codes mandate installation of pads with these particular characteristics. Currently these locales include most of Southern
California, portions of Washington, and portions of Oregon.
SOURCE 1 PART NO.
LENGTH
WIDTH
THICKNESS
PALLET QTY.
MLP $
S1-UC2424-3CA
S1-UC2436-3CA
S1-UC3030-3CA
S1-UC3036-3CA
S1-UC3040-3CA
S1-UC3232-3CA
S1-UC3445-3CA
S1-UC3636-3CA
S1-UC3642-3CA
S1-UC3648-3CA
S1-UC4040-3CA
24
24
30
30
30
32
34
36
36
36
40
24
36
30
36
40
32
45
36
42
48
40
3
3
3
3
3
3
3
3
3
3
3
15
15
15
15
15
15
15
15
15
15
15
45.21
71.89
64.36
100.25
88.89
78.00
114.93
96.93
109.21
129.04
137.18
DiversiTech CladLite® Equipment Pad
Available in more than 70 sizes, the pad’s durable cladding provides superior resistance to sun, moisture and freeze/thaw conditions.
The vibration-damping EPS foam core is unaffected by water, soil conditions, fungus or bacteria.
Specifications:
Allowable Load: 125 lbs. per 2” diameter foot Freeze/Thaw Testing: Flawless performance under the 25-cycle regimen specified by
ASTM C67.
Chemical Resistance: Does not craze, soften, delaminate or spall when tested per ASTM D2299 with the following: R-22 and R134a; compressor oil; synthetic canine urine; and salt solution, 20% by volume
Foam Core: ASTM Type 1 EPS
Flame Resistance: Cladding resists compressor heat and incidental torch contact. Not to be used under heating devices.
Code Approvals: ICBO No. PFC-5112, LA City RR No. 7570
SOURCE 1 PART NO.
DESCRIPTION
THICKNESS (IN INCHES)
MLP $
S1-52633854001
S1-52638626001
S1-52638627001
S1-52638628001
S1-52638629001
S1-52638630001
S1-52638632001
S1-52638634001
S1-52638636001
S1-52638637001
S1-52638638001
S1-52638639001
S1-52638640001
S1-52638641001
S1-52638642001
S1-52638644001
S1-52638646001
S1-52638648001
S1-52638652001
S1-52638654001
S1-52638655001
S1-52639536000
S1-52639537000
S1-52639538000
UNIT CLADLITE PAD
UNIT CLADLITE PAD
UNIT CLADLITE PAD
UNIT CLADLITE PAD
UNIT CLADLITE PAD
UNIT CLADLITE PAD
UNIT CLADLITE PAD
UNIT CLADLITE PAD
UNIT CLADLITE PAD
UNIT CLADLITE PAD
UNIT CLADLITE PAD
UNIT CLADLITE PAD
UNIT CLADLITE PAD
UNIT CLADLITE PAD
UNIT CLADLITE PAD
UNIT CLADLITE PAD
UNIT CLADLITE PAD
UNIT CLADLITE PAD
UNIT CLADLITE PAD
UNIT CLADLITE PAD
UNIT CLADLITE PAD
CLADLITE A/C SLAB
CLADLITE A/C SLAB
CLADLITE A/C SLAB
26 x 26
24 x 24
24 x 36
30 x 30
30 x 36
30 x 40
32 x 32
36 x 36
36 x 48
48 x 48
24 x 24
24 x 36
30 x 30
30 x 36
30 x 40
32 x 32
36 x 36
36 x 48
28 x 38
38 x 28
45 x 33
36 x 40
41 x 47
32 x 37
2
3
3
3
3
3
3
3
3
3
2
2
2
2
2
2
2
2
2
3
3
3
3
3
49.54
43.43
64.29
72.21
86.14
92.82
80.50
99.32
132.39
189.25
39.25
62.79
65.61
73.61
84.64
73.29
90.29
120.25
77.64
81.50
120.25
113.25
158.32
95.68
S1-52639540000
S1-52642206000
S1-52642269000
S1-52642348000
CLADLITE A/C SLAB
UNIT CLADLITE PAD
UNIT CLADLITE PAD
UNIT CLADLITE PAD
24 x 48
36 x 40
26 x 26
50 x 53
3
2
3
3
86.29
102.71
51.11
237.18
244
DiversiTech CladLite® Hurricane Equipment Pads
Designed specifically for the hurricane-prone regions of Florida and the Gulf Coast, the CladLite Hurricane pad meets stringent local
code requirements for wind resistance. Heavier than a normal concrete pad, this pad provides sufficient weight to meet code. These
pads have been designed specifically to meet the intent of the Florida Building Code, Chapter 16, with respect to wind resistance.
Method of attachment tested per ASCE 7. CladLite Hurricane pads are suitable for all 130-mph and most 150-mph installations. For
certain taller equipment, the CladLite Hurricane T pad is needed. CladLite Hurricane pads have been declared by the Florida Building
Commission to be an acceptable alternative material to solid concrete slabs for use in specific applications from Tallahassee to Miami.
Approval of the pad is within the discretion of the local building inspector. DCA02-DEC-183.
SOURCE 1 PART NO.
LENGTH
WIDTH
THICKNESS
PALLET QTY.
MLP $
S1-H2424-4
S1-H2436-4
S1-H3030-4
S1-H3060-4
S1-H3232-4
S1-H3345-4
S1-H3636-4
S1-H3642-4
S1-H3648-4
S1-H3652-4
S1-H3672-4
S1-H3842-4
S1-H3852-4
S1-H3865-4
S1-H4040-4
S1-H4242-4
S1-H4558-4
24
24
30
30
32
33
36
36
36
36
36
38
38
38
40
42
45
24
36
30
60
32
45
36
42
48
52
72
42
52
65
40
42
58
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
16
16
16
16
16
16
16
16
16
8
8
16
8
8
8
8
8
51.29
79.04
85.14
157.89
94.93
137.54
113.86
132.64
151.57
184.36
269.64
147.54
176.43
226.29
140.39
157.21
280.39
DiversiTech CladLite® Hurricane T Equipment Pads
The CladLite Hurricane T pad is even heavier than the CladLite Hurricane pad and is designed to meet the higher wind loads of taller
equipment. The taller the piece of equipment mounted to the pad, the greater the wind load on the pad. These pads provide sufficient
weight to meet code for these tall condensing units.CladLite Hurricane equipment pads have been designed specifically to meet the
intent of the Florida Building Code, Chapter 16, with respect to wind resistance. Method of attachment tested per ASCE 7. CladLite
Hurricane pads are suitable for all 130-mph and most 150-mph installations. For certain taller equipment, the CladLite Hurricane T
pad is needed. CladLite Hurricane pads have been declared by the Florida Building Commission to be an acceptable alternative
material to solid concrete slabs for use in specific applications from Tallahassee to Miami. Approval of the pad is within the discretion
of the local building inspector. DCA01-DEC-183.
SOURCE 1 PART NO.
LENGTH
WIDTH
THICKNESS
PALLET QTY.
MLP $
S1-HT1840-4
S1-HT2424-4
S1-HT2436-4
S1-HT3030-4
S1-HT3232-4
S1-HT3636-4
S1-HT3648-4
S1-HT4558-4
18
24
24
30
32
36
36
45
40
24
36
30
32
36
48
58
4
4
4
4
4
4
4
4
10
10
10
10
10
10
10
10
83.86
67.61
103.14
111.54
126.54
153.64
204.61
353.18
DiversiTech Hurricane Pad Attachment Bracket
• Pack of 4 pcs
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-HC-1
HURRICANE PAD BRACKET - PACK OF 4
10.11
245
E.V.A. Anti-Vibration Pad
The latest generation in vibration dampening technology. The most effective vibration dampening pad available on the market. The
EVA (Extreme Vibration Attenuation) Pad was tested against other pads at four different vibration settings. In the most severe
vibration extremes, the EVA Pad outperforms cork and rubber by a margin of greater than 3:1! This is due to the special composite
foam center which is much more structurally sound than cork. It is not affected by oils or chemicals that can break down cork and is
much more effective at vibration dampening than solid rubber. All this at a very competitive price. Designed to withstand 50 psi.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-MP-12E
S1-MP-18E
S1-MP-2E
S1-MP-3E
S1-MP-4E
S1-MP-6E
E.V.A. PAD
E.V.A. PAD
E.V.A. PAD
E.V.A. PAD
E.V.A. PAD
E.V.A. PAD
12 x 12
18 x 18
2x2
3x3
4x4
6x6
7/8
7/8
7/8
7/8
7/8
7/8
12
6
48
36
24
24
56.12
59.16
1.18
2.75
3.88
8.93
Iso-Cube Anti-Vibration Pad
Natural rubber pads, designed to reduce vibration and noise emanating from refrigeration and air conditioning equipment. The circular
design in each pad offers a suction cup effect, which eliminates the need to bolt the pads down. A standard 18” (46cm) pad is divided
into Eightyone 2” (5cm) segments, each of which may be cut or torn to provide smaller pads. These 50 durometer pads will withstand
a load of 180 psi with greater resiliency.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-ISO-18
S1-ISO-2
S1-ISO-4
ISO-CUBE
ISO-CUBE
ISO-CUBE
18 x 18
2x2
4x4
3/4
3/4
3/4
6
24
12
83.24
1.93
7.56
Rubber Anti-Vibration Pad
Highest quality elastomeric oil resistant padding. Designed to withstand 50 lbs. psi. The rubber pads are corrugated on both sides.
Ideal for air conditioners, compressors, cooling towers, presse s, machines, etc.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-MP-12
S1-MP-18
S1-MP-2
S1-MP-3
S1-MP-4
S1-MP-6
S1-MP-8
RUBBER
RUBBER
RUBBER
RUBBER
RUBBER
RUBBER
RUBBER
12 x 12
18 x 18
2x2
3x3
4x4
6x6
8x8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
12
6
48
36
24
24
12
29.52
31.69
0.50
1.07
1.50
3.29
14.02
*Sol d by pack / M LP per each
Rubber/Cork Anti-Vibration Pad
Highest quality elastomeric oil resistant padding. Designed to withstand 50 psi. T he rubber pads are corrugated on both sides. The
cork is laminated between two corrugated pads. Ideal for air conditioners, compressors, cooling towers, presses, machines, etc.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-MP-12C
S1-MP-18C
S1-MP-2C
S1-MP-3C
S1-MP-4C
S1-MP-6C
S1-MP-8C
RUBBER/CORK
RUBBER/CORK
RUBBER/CORK
RUBBER/CORK
RUBBER/CORK
RUBBER/CORK
RUBBER/CORK
12 x 12
18 x 18
2x2
3x3
4x4
6x6
8x8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
12
6
48
36
24
24
12
46.81
48.37
0.68
1.36
2.62
5.43
21.54
246
DiversiTech Heat Pump PadTM
The Heat Pump Pad™ provides 8” of lift and is ideal for snowy areas or where it is desirable to have the unit up off the ground.
SOURCE 1 PART NO.
DESCRIPTION
ORDER MULTIPLE
MLP $
S1-HP3636-8
HEAT PUMP PAD - 36" x 36" x 8"
16
111.93
Heat Pump Risers
Sturdy and stable, DiversiT ech’s Heat Pump Riser provides the desired elevation for condensers, heat pumps,
and air handlers. The one-piece, heavy-duty plastic unit is manufactured in three heights. Butyl mastic on the
top and bottom guarantees no slipping and reduced vibration and noise. Available in 1 or 2 piece risers.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-HPR-12
S1-HPR-3
S1-HPR-3-2P
S1-HPR-3-2PG
S1-HPR-6
S1-HPR-6-2P
S1-HPR-6-2PG
S1-HPR-EXT
RISER – 12”
RISER – 3”
TWO PIECE RISER – 3”
TWO PIECE DARK GRAY RISER – 3”
RISER – 6”
TWO PIECE RISER – 6”
TWO PIECE DARK GRAY RISER – 6”
4” EXTENSION
16
48
32
32
36
16
16
28
8.79
4.14
5.46
8.25
4.89
6.68
9.89
4.04
*Sol d by case / MLP per each
DiversiTech Air Conditioner Brackets
These heavy duty 1/8” thick steel AC brackets are perfect for hanging A/C condensers and heat pumps outside
the home. Mount at any height to allow for easy maintenance under units. No need to wait for finished grade or
landscaping prior to installation of AC unit. Pre-punched holes for easy installation. Powder coated gray finish.
Load rating 600 lbs. per pair.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ACB-30
S1-ACB-36
S1-ACB-42
S1-ACB-48
AC MOUNTING BRACKET, 30", PAIR
92.14
100.00
69.32
131.39
Furnace Mounting Blocks
Each furnace mounting block can support 40% more weight than competitive products – over 500 pounds! Easy peel and stick
installation. DiversiTech’s Furnace Mounting Blocks also feature rubber feet for vibration and noise elimination.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-FB-1
FURNACE MOUNTING BLOCK
72
6.89
Air Handler Block
Lightweight styrofoam block (concrete gray) provides A/C air handler support in attic installations.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-7-60
S1-7-64
AIR HANDLER 8” x 8” x 4”
AIR HANDLER 8” x 8” x 4” – 4/PACK
144/CASE
4 PACKS/CASE
4.68
24.25
**M LP per pack
247
Water Heater Installation Accessories
GAS WATER HEATER STAND
• Allows the placement of water heater tanks 18" above the ground as required by the National Fuel Gas Code
• Constructed of 18 gauge spangled galvanized sheet metal, holds up to 50 gallon water heaters
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-34057
GALVANIZED WATER HEATER STAND - 21" SQUARE X 18" HIGH
95.14
Down Flow Filter Housing
Features:
• Allows access to filters without interference from vent pipe
• Use s standard size filters in 1” thickness only
• Heavy gauge, embossed steel, fully insulated
• Filters positioned on angle for maximum surface area
OVERALL
DUCT OPENING
UNIT OPENING
SOURCE 1 PART NO.
MODEL NO.
A
B
C
D
E
F
G
FLTR. QTY.
FILTER SIZE
MLP $
S1-52636167000
S1-52636168000
S1-52636169000
CF1
CF2
CF3
15-3/4
18-3/4
23-1/4
21-3/8
21-3/8
21-3/8
12
12
12
13-3/4
16-3/4
21-1/4
19-7/8
19-7/8
19-7/8
12-5/8
16-1/8
20
20-1/8
20-1/8
20-1/8
2
3
3
10 x 20 x 1
10 x 20 x 1
10 x 20 x 1
187.50
217.64
232.14
Horizontal Filter Housing
•
•
•
•
•
Use s standard size filters in 1”, 2” and 4” thickness
Heavy gauge, embossed, galvanized steel construction
Fully insulated
HRB model is blocked off on both sides, cut to fit your furnace specifications and the existing plenum
HR model is open on one side and blocked off on the other side, cut blocked side to your furnace specifications
OVERALL
DUCT OPENING
SOURCE 1 PART NO.
MODEL NO.
A
B
C
D
E
FILTER SIZE
MLP $
S1-52636163000
S1-52636164000
S1-52636165000
S1-52636166000
HR20
HR25
HRB20
HRB25
6-5/8
6-5/8
6-5/8
6-5/8
25-1/2
20-1/2
25-1/2
20-1/2
22
27
22
27
19-3/4
19-3/4
—
—
19
19
—
—
20 x 25
20 x 25
20 x 25
20 x 25
112.71
112.71
123.89
123.89
McDaniel Metals Accomodator Filter Housing
Specifications For Electric Furnaces, Air Handlers and Coil Cabinets
OUTSIDE DIMENSION
TOP
DUCT
OPENING
SOURCE 1 PART NO.
MFG. PART NO.
A
B
C
D
E
F
G
FILTER SIZE
USE ON MODEL NO.
MLP $
S1-52636178001
ACE 1620-3
17-3/8
22
3-3/4
14-7/8
19
1-1/2
1
16 x 20
127.25
S1-52636178002
ACE 1620-6
17-3/8
22
5-3/4
14-7/8
19
1-1/2
1
16 x 20
S1-52636179001
ACE 2020-3
21-3/8
22
3-3/4
18-7/8
19
1-1/2
1
20 x 20
S1-52636179002
ACE 2020-6
21-3/8
22
5-3/4
18-7/8
19
1-1/2
1
20 x 20
S1-52636180001
ACE 2025-3
26-3/8
22
3-3/4
23-7/8
19
1-1/2
1
25 x 20
S1-52636180002
ACE 2025-6
26-3/8
22
5-3/4
23-7/8
19
1-1/2
1
25 x 20
F2RP018 F2RP036 (RP)
G2FD024S17 F2RP024 N1AHB08
F2RP018 F2RP036 (RP)
F2RP036 (RC) G2FD036S21
N1AHC16 G2FD046S17
G2FD042S21 G2FD036S17
G2FD048S21
F2RP036 (RC) G2FD036S21
N1AHC16 G2FD046S17
G2FD042S21 G2FD036S17
G2FD048S21
N1AHD20 G2FD048S24
G2FD060S24
N1AHD20 G2FD048S24
G2FD060S24
248
146.21
138.39
157.50
146.21
161.82
McDaniel Metals Accomodator Filter Housing
Specifications For Gas Furnaces
OUTSIDE DIMENSION
TOP
DUCT
OPENING
SOURCE 1 PART NO.
MFG. PART NO.
A
B
C
D
E
F
G
FILTER SIZE
USE ON MODEL NO.
MLP $
S1-52636173001
ACG 1425-3
15-3/8
28-3/8
3-3/4
12-7/8
26
1-1/2
1
14 x 25
127.25
S1-52636173002
ACG 1425-6
15-3/8
28-3/8
5-3/4
12-7/8
26
1-1/2
1
14 x 25
S1-52636174001
ACG 1625-3
17-3/8
28-3/8
3-3/4
14-7/8
26
1-1/2
1
16 x 25
S1-52636174002
ACG 1625-6
17-3/8
28-3/8
5-3/4
14-7/8
26
1-1/2
1
16 x 25
S1-52636175001
ACG 2025-3
21-3/8
28-3/8
3-3/4
18-7/8
26
1-1/2
1
20 x 25
S1-52636175002
ACG 2025-6
21-3/8
28-3/8
5-3/4
18-7/8
26
1-1/2
1
20 x 25
S1-52636176001
S1-52636176002
ACG 2424-3
ACG 2424-6
25-3/8
25-3/8
28-3/8
28-3/8
3-3/4
5-3/4
22-7/8
22-7/8
26
26
1-1/2
1-1/2
1
1
24 x 24
24 x 24
P3UHA08N03201 P3UH12N04801
P3UHA12N03201 P3UH12N06401
P3UHA08N04801
P3UHA08N03201 P3UH12N04801
P3UHA12N03201 P3UH12N06401
P3UHA08N04801
P3UHB16N06401
P3UHB12N08001
P3UHB16N08001
P3UHB16N06401
P3UHB12N08001
P3UHB16N08001
P3UC20N06401 P3UC20N09201
P3UC20N08001 P3UC16N09201
P3UC20N06401 P3UC20N09201
P3UC20N08001 P3UC16N09201
P3UD20N10401
P3UD20N10401
146.21
127.25
146.21
138.39
161.82
146.21
161.82
McDaniel Metals Labor Saver Filter Housing
McDaniel Metals, Inc.
•
•
•
•
•
•
•
•
Raises furnace to plenum for fast installation; overall height: 14”
Provides access to filter without entering the furnace compartment
Use s standard filter sizes and 1”, 2” or 4” filters
Available in 1 - 3 ton and 3.5 - 5 ton sizes. Heavy gauge steel construction
Easy access from both sides
Insulated on all sides
Filter is angled for maximum surface area. No hardware to remove for access
Usually eliminates dual side returns
SOURCE 1 PART NO.
MFG. MODEL NO.
A
B
C
D
E
F
G
H
FILTER SIZE STANDARD
MLP $
S1-52636171000
S1-52636172000
S1-LS2232
S1-LS2240
LS 2832
LS 2840
LS 2232
LS 2240
28-1/2
28-1/2
22-1/2
22-1/2
32
40
32
40
26-1/2
26-1/2
20-1/2
20-1/2
13-1/2
19
14-1/2
20
24
24
20-1/2
20-1/2
8
10
9-1/2
12
6-1/2
7
5
5
3
3
2
2
20 x 25
24 x 24
20 x 20
20 x 25
485.50
551.36
460.93
524.57
McDaniel Metals Supply Plenums
OVERALL
SOURCE 1 PART NO.
MODEL NO.
APPLICATION
DIMENSIONS
INSULATION
MLP $
S1-133/8X203/8X36R
S1-133/8X203/8X48R
S1-13X161/2X36R
S1-13X161/2X48R
S1-13X20X36R
S1-13X20X48R
S1-13X231/2X36R
S1-13X231/2X48R
S1-163/8X203/8X36R
S1-163/8X203/8X48R
S1-197/8X203/8X36R
S1-197/8X203/8X48R
S1-233/8X203/8X36R
S1-233/8X203/8X48R
133/8X203/8X36R
133/8X203/8X48R
13X161/2X36R
13X161/2X48R
13X20X36R
13X20X48R
13X23.5X36R
13X23.5X48R
163/8X203/8X36R
163/8X203/8X48R
197/8X203/8X36R
197/8X203/8X48R
233/8X203/8X36R
233/8X203/8X48R
EVAP
EVAP
AHU
AHU
AHU
AHU
AHU
AHU
EVAP
EVAP
EVAP
EVAP
EVAP
EVAP
13.38 x 20.38 x 36
13.38 x 20.38 x 48
13 x 16.5 x 36
13 x 16.5 x 48
13 x 20 x 36
13 x 20 x 48
13 x 23.5 x 36
13 x 23.5 x 48
16.38 x 20.38 x 36
16.38 x 20.38 x 48
19.88 x 20.38 x 36
19.88 x 20.38 x 48
23.38 x 20.38 x 36
23.38 x 20.38 x 48
R-6
R-6
R-6
R-6
R-6
R-6
R-6
R-6
R-6
R-6
R-6
R-6
R-6
R-6
129.46
166.29
116.07
148.43
126.11
162.96
138.39
176.36
139.5
178.57
151.79
194.21
162.96
208.71
Return Air Plenums by McDaniel Metals
SOURCE 1 PART NO.
WIDTH
LENGTH
MLP $
S1-RAFP1625
S1-RAFP2025
16
20
25
25
169.64
183.04
249
Welded Steel Drain Pans by McDaniel Metals
Features:
• 22 Gauge Galvanized Steel
• Welded Corners
• Welded 3/4MPT Fitting on Long Side
SOURCE 1 PART NO.
WIDTH
LENGTH
MLP $
S1-14X44W
S1-32X36W
S1-32X40W
S1-32X60W
S1-32X72W
14
32
32
32
32
44
36
40
60
72
33.50
53.57
58.04
78.14
85.93
McDaniel Metals Duct Access Doors
OVERALL
SOURCE 1 PART NO.
MODEL NO.
LATCH STYLE
S1-10X10AD
S1-10X10ADEF
S1-12X12AD
S1-12X12ADEF
S1-6X6AD
S1-6X6ADEF
S1-8X8AD
S1-8X8ADEF
10X10AD
10X10ADEF
12X12AD
12X12ADEF
6X6AD
6X6ADEF
8X8AD
8X8ADEF
TWIN CAM
TWIN CAM
TWIN CAM
TWIN CAM
TWIN CAM
TWIN CAM
TWIN CAM
TWIN CAM
SPECIAL
DUCT OPENING
DIMENSIONS
INSULATION
MLP $
10 x 10
10 x 10
12 x 12
12 x 12
6x6
6x6
8x8
8x8
R-6
R-6
R-6
R-6
R-6
R-6
R-6
R-6
37.96
42.43
46.89
51.36
26.79
29.04
31.25
35.71
EXT TABS
EXT TABS
EXT TABS
EXT TABS
Duct Strap, Ties, Clamps
Plastic Hanger Strap
SOURCE 1 PART NO.
DESCRIPTION
ORDER MULTIPLE
MLP $
S1-710-P100
STRAP,HANGER,3/4"W X 100' ROLL
20
20.39
Metallic Duct Hanging Strap
• 30-Gauge, 1-1/2" wide X 100' long
• 28-Gauge, Hole Punched
SOURCE 1 PART NO.
DESCRIPTION
S1-710-003
S1-710-A16100
METALLIC DUCT HANGER - 30 GA, 1-1/2" WIDE, 100' ROLL
METALLIC DUCT HANGER - 28 GA, HOLE PUNCHED, 100'
ROLL
ROLL
ROLL
S1-710-A1650
S1-710-A1710
SHIPPING
MULTIPLE
MLP $
10
39.75
25.82
10
13.00
50
3.29
Nylon Duct Hanging Strap
• Woven Polypropylene
SOURCE 1 PART NO.
DESCRIPTION
SHIPPING MULTIPLE
COLOR
MLP $
S1-710-100
S1-710-101
S1-710-102
1-3/4" x 100 YD
1-3/4" x 100 YD
3" x 100 YD
24
24
8
BLACK
SILVER
BLACK
12.86
12.50
38.21
250
Pipe Hangers
• DWV Swiveling J-Hooks
SOURCE 1 PART NO.
DESCRIPTION
SHIPPING MULTIPLE
MLP $
S1-515-J2000
S1-515-J3000
2" x 7-1/2"
3" x 7-1/2"
25
25
2.43
2.86
251
Screws & Fasteners
SHEET METAL SCREWS
Sheet Metal Schrews - Taper Point
Hex washer slotted head. Burr-free. Full 1/4” head will not strip out of hex driver opening. Heat treated tapered
pointwill not break or “walk”. Packaged in resealable plastic cartons.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-5-SCR101
S1-5-SCR101-2
S1-5-SCR101BULK
S1-5-SCR103-4
S1-5-SCR103-4BULK
S1-5-SCR63-8
S1-5-SCR63-8BULK
S1-5-SCR71-2
S1-5-SCR71-2BULK
S1-5-SCR81
S1-5-SCR81-12
S1-5-SCR81-12BULK
S1-5-SCR81-12W
S1-5-SCR81-2
S1-5-SCR81-2BULK
S1-5-SCR81BULK
S1-5-SCR82
S1-5-SCR82BULK
S1-5-SCR82W
S1-5-SCR83-4
S1-5-SCR83-4BULK
10 x 1 TAPER POINT
10 x 1/2 TAPER POINT
10 x 1 TAPER POINT – BULK
10 x 3/4 TAPER POINT
10 x 3/4 TAPER POINT – BULK
6 x 3/8 TAPER POINT
7 x 1/2 TAPER POINT
8 x 1 TAPER POINT
8 x 1-1/2 TAPER POINT
8 x 1-1/2 TAPER POINT – BULK
X 1-1/2 TAPER POINT WITH WHITE HEAD
8 x 1/2 TAPER POINT
8 x 2 TAPER POINT
8 x 2 TAPER POINT WITH WHITE HEAD
8 x 3/4 TAPER POINT
500
1,000
7,000
1,000
10,000
1,000
20,000
1,000
15,000
500
250
5,000
250
1,000
12,000
7,500
350
3,000
250
1,000
10,000
31.79
46.04
418.82
53.79
515.39
27.82
537.64
26.82
426.54
24.93
17.64
322.14
21.04
25.93
301.50
346.57
30.46
257.75
40.46
38.89
364.36
*Sol d by Standard Pack / M LP per Standard Pack
Sheet Metal Screws – Drill Point
Self-drilling, self-tapping. Hex washer head. Produces the optimum hole size, resulting in a tighter fit. Made from
special heat treated steel for extra strength. Packaged in resealable plastic cartons.
SOURCE 1 PART NO.
DESCRIPTION
HEAD SIZE
STD. PACK
MLP $
S1-5-SCR101-12DP
S1-5-SCR101-12DPBU
S1-5-SCR101-2DP
S1-5-SCR101-2DPBUL
S1-5-SCR101DP
S1-5-SCR101DPBULK
S1-5-SCR102DP
S1-5-SCR102DPBULK
S1-5-SCR103-4DP
S1-5-SCR103-4DPBUL
S1-5-SCR61-2DP
S1-5-SCR61-2DPBULK
S1-5-SCR81-12DP
S1-5-SCR81-12DPBUL
S1-5-SCR81-2DP
S1-5-SCR81-2DPBULK
S1-5-SCR81DP
S1-5-SCR81DPBULK
S1-5-SCR82DP
S1-5-SCR82DPBULK
S1-5-SCR83-4DP
S1-5-SCR83-4DPBULK
10 x 1-1/2 DRILL POINT
10 x 1-1/2 DRILL POINT – BULK
10 x 1/2 DRILL POINT
10 x 1/2 DRILL POINT – BULK
10 x 1 DRILL POINT
10 x 1 DRILL POINT – BULK
10 x 2 DRILL POINT
10 x 3/4 DRILL POINT
6 x 1/2 DRILL POINT
8 x 1-1/2 DRILL POI
8 x 1-1/2 DRILL POINT – BULK
8 x 1/2 DRILL POINT
8 x 1 DRILL POINT
8 x 2 DRILL POINT
8 x 3/4 DRILL POINT
5/16"
5/16"
5/16"
5/16"
5/16"
5/16"
5/16"
5/16"
5/16"
5/16"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
250
3,500
500
10,000
500
5,000
350
2,500
500
5,000
1,000
15,000
500
5,000
1,000
10,000
500
7,500
350
2,500
500
10,000
25.32
329.68
42.59
565.14
38.89
369.68
39.00
280.39
33.57
317.71
40.61
586.50
46.04
442.11
40.93
399.89
30.68
435.43
40.71
277.71
25.79
479.89
252
Screws & Fasteners
SHEET METAL SCREWS & ANCHOR KITS
Anchor Kit
Plastic anchor kit for sheet rock applications. Kit includes 100 anchors, screws and 1 masonry bit.
SOURCE 1 PART NO.
DESCRIPTION
HEAD SIZE
STD. PACK
MLP $
S1-540-AK100
ANCHOR SIZE 1/4 x 1, SCREW SIZE 10 x 1-1/4
HWH
5/16 HEX
100/BOX
14.32
Machine Nuts Assortment
• 23 pcs each of #6-32, #8-32, and #10-32
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6500A
MACHINE NUTS ASSORTMENT
5.43
Sheet Metal Screw Assortment Kit
The 7 most popular sizes in one multi-compartmented, resealable, plastic container. Perfect for the toolbox.
Contains:
• 7 x 1/2 Taper Point – 175 pieces
• 8 x 1/2 Drill Point – 100 pieces
• 8 x 1 Taper Point – 50 pieces
• 8 x 1-1/2 Taper Point – 50 pieces
• 8 x 2 Taper Point – 40 pieces
• 1/4” Nut Setter – 1 each
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-5-SCR-AK
SHEET METAL SCREW ASSORTMENT PACK
40.00
253
Source 1 Innerflow™ Condenser Covers
Innerflow™ Winter Covers for Affinity, Acclimate, and Echelon Condensing Units
FITS UNIT DIMENSIONS
SOURCE 1 PART NO.
L
W
H
S1-CCVRZL39
42
34
39.5
S1-CCVRZS29
37
31
29.5
S1-CCVRZS33
37
31
33.5
S1-CCVRZS39
37
31
39.5
FITS UNITS
YORK
LUXAIRE
COLEMAN
INCLUDES BRAND
LABELS
AFFINITY, ACCLIMATE,
ECHELON
CMB48, CMB60, CZF48, AL3A48, AL3A60, AL8B24,
CZF60, CZH24, CZH36, AL8B36, AL8B48, AL8B60
CZH48, CZH60
CMB18, CMB24, CZB18, AL3A18, AL3A24, AL3B18,
CZB24
AL3B24
CMB30, CMB36, CZB30, AL3A30, AL3A36, AL3B30,
CZB36, CZE024
AL3B36, AL5B024
CMB42, CZB42, CZB48,
CZB60, CZE36, CZE48,
CZE60, CZF36, CZF42
AC3A48, AC3A60,
AC8B24, AC8B36,
AC8B48, AC8B60
AC3A18, AC3A24,
AC3B18, AC3B24
ECHELON
AC3A30, AC3A36,
AC3B30, AC3B36,
ECHELON
AC5B024
AL3A42, AL3B42, AL3B48,
AC3A42, AC3B42,
AL3B60, AL5B36, AL5B48,
AC3B48, AC3B60,
ECHELON
AL5B60
AC5B36, AC5B48, AC5B60
MLP $
125.00
114.29
114.29
125.00
Innerflow™ Winter Covers for Microchannel Condensing Units
FITS UNIT DIMENSIONS
FITS UNITS
SOURCE 1 PART NO.
L
W
H
YORK
LUXAIRE
COLEMAN
GUARDIAN
S1-CCVRYL28
29
29
28
S1-CCVRYL30
29
29
30
S1-CCVRYL34
29
29
34
S1-CCVRYL36
29
29
36
S1-CCVRYL40
29
29
40
S1-CCVRYS24
23.5
23.5
24
S1-CCVRYS28
23.5
23.5
28
S1-CCVRYS32
23.5
23.5
32
TCGD18S2,
TCGD18S2,
TCGD18S2,
TCGD24S2,
TCGD24S2,
TCGD24S2,
TCGD18S4,
TCGD18S4,
TCGD18S4,
TCGD24S4,
TCGD24S4,
TCGD24S4,
TCGD30S4,
TCGD30S4, LCJD18S2,
TCGD30S4,
YCJD18S2, YCJD24S2, LCJD24S2, LCJD18S4, CCJD18S2, CCJD24S2,
YCJD18S4, YCJD24S4, LCJD24S4, LCJD30S4 CCJD18S4, CCJD24S4,
YCJD30S4
CCJD30S4
TCGD30S2, YCJD30S2 TCGD30S2, LCJD30S2 TCGD30S2, CCJD30S2
S1-CCVRYS34
23.5
23.5
34
S1-CCVRYX32
33.5
33.5
32
S1-CCVRYX34
33.5
33.5
34
TCGF42, YCJF42
TCGF42, LCJF42
TCGF42, CCJF42
S1-CCVRYX36
33.5
33.5
36
TCGF48, YCJF48
TCGF48, LCJF48
TCGF48, CCJF48
S1-CCVRYX40
33.5
33.5
40
TCGF60, YCJF60
TCGF60, LCJF60
TCGF60,CCJF60
TCGD36S4, TCGF24, TCGD36S4, TCGF24, TCGD36S4, TCGF24,
TCJF24, YCJD36S4,
LCJD36S4, LCJF24
CCJD36S4, CCJF24
YCJF24
TCGD42S4,
TCGD42S4,
TCGD42S4,
TCGD48S4,
TCGD48S4, LCJD42S4,
TCGD48S4,
YCJD42S4, YCJD48S4
LCJD48S4
CCJD42S4, CCJD48S4
TCGD42S2,
TCGD42S2,
TCGD42S2,
TCGD48S2,
TCGD48S2, LCJD42S2,
TCGD48S2,
YCJD42S2, YCJD48S2
LCJD48S2
CCJD42S2, CCJD48S2
TCGF30, TCGF36,
TCGF30, TCGF36,
TCGF30, TCGF36,
YCJF30, YCJF36
LCJF30, LCJF36
CCJF30, CCJF36
TCGD12S2
TCGD12S2
TCGD12S2
GCGD24
GCGD30
INCLUDES BRAND
LABELS
YORK, COLEMAN,
GUARDIAN, LUXAIRE
MLP $
107.14
YORK, COLEMAN,
GUARDIAN, LUXAIRE
107.14
YORK, COLEMAN,
GUARDIAN, LUXAIRE
107.14
YORK, COLEMAN,
GUARDIAN, LUXAIRE
YORK, COLEMAN,
GUARDIAN, LUXAIRE
YORK, COLEMAN,
GUARDIAN, LUXAIRE
YORK, COLEMAN,
GUARDIAN, LUXAIRE
107.14
YORK, COLEMAN,
GUARDIAN, LUXAIRE
YORK, COLEMAN,
GUARDIAN, LUXAIRE
YORK, COLEMAN,
GUARDIAN, LUXAIRE
YORK, COLEMAN,
GUARDIAN, LUXAIRE
YORK, COLEMAN,
GUARDIAN, LUXAIRE
YORK, COLEMAN,
GUARDIAN, LUXAIRE
96.43
107.14
85.71
96.43
96.43
114.29
114.29
114.29
125.00
Anaconda® Vibration Eliminators
Anaconda® Bronze Vibration Eliminators with Female Ends
TO FIT COPPER TUBE
DIMENSIONS
SOURCE 1 PART NO.
ACTUAL O.D. (IN.)
NOM. (IN.)
FLEXIBLE HOSE I.D.
(IN.)
H ±1/4 (IN.)
A MAX. (IN.)
B MAX. (IN.)
E ±1/8 (IN.)
S1-1212FY
S1-1258FY
S1-3838FZ
S1-5454FY
5/8
3/4
1/2
1-3/8
1/2
5/8
3/8
1-1/4
1/2
1/2
3/8
1-1/4
9-3/4
10
9
14-3/4
1
1
3/4
2-1/8
1-1/8
1-1/8
7/8
2-1/4
7/8
1
3/4
1-5/8
MAXIMUM
OPERATING
PRESSURE PSI
450
450
500
500
MLP $
77.43
62.79
50.32
131.36
Anaconda® Stainless Steel Vibration Eliminators with Female Ends
TO FIT COPPER TUBE
DIMENSIONS
SOURCE 1 PART NO.
ACTUAL O.D. (IN.)
NOM. (IN.)
FLEXIBLE HOSE I.D.
(IN.)
H ±1/4 (IN.)
A MAX. (IN.)
MAX. (IN.)
E ±1/8 (IN.)
S1-6464FS
1-5/8
1-1/2
1-1/2
17
2-1/4
2-3/8
2
254
MAXIMUM
OPERATING
PRESSURE PSI
400
MLP $
218.82
NOTES:
1. Maximum test pressure 1-1/2 x operating pressure shown.
2. Minimum burst pressure 5 x operating pressure shown.
3. I.D. of copper tube ends for depth "K" meets ANSI STD B16.18 1978 and ANSI B16.22 1973.
4. Copper tube ends to fit sizes above 3-1/8" O.D. are commercial parts and E&H may exceed tolerances shown.
5. Bagged and boxed. Size 5"–8" are bagged only.
Novent Multikey
T he m ul tikey fits all Novent locki ng refri gerant caps.
SOURCE 1 PART NO.
DESCRIPTION
S1-NVMULTIKEY
NOVENT CAPS, UNIVERSAL, 50-PK
USE WITH
REFRIGERANT
-
PKG. QTY.
MLP $
20
22.39
Novent Refrigerant Caps, Universal 50 Pack
Novents Tamper Resistant caps have become the standard in sealing and protecting Schraeder service valves. Safe guard your AC
sy stems efficiency and the environment from lost or accidental mixing of refrigerant gases.
Specifications:
T hread Size - 1/4"
Refrigerant - ANY
SOURCE 1 PART NO.
DESCRIPTION
S1-NSUNI50PK
NOVENT CAPS, UNIVERSAL, 50-PK
USE WITH
REFRIGERANT
-
PKG. QTY.
MLP $
-
604.79
®
Novent Refrigerant Locking Caps
Novent Caps fit the standard “Schraeder” service valve on all central AC units and Minisplits, and provide an innovative way to prevent access by unauthorized
persons. Patented Novent Caps are precision machined from high grade brass surrounded by a protective aluminum shroud and can only be fitted and
removed with a special tool. Novent Caps seal the service valve to prevent leaks, prevent excessive energy usage due to refrigerant loss, help prevent illegal
venting of refrigerant, and deter refrigerant theft at unsecured sites. Potential liability for inhalation-induced injury or death will be greatly reduced.
Features:
• Corrosion resistant
• Integral neoprene O-ring resists all oils
• R22 and R410 caps are color coded and embossed for easy identification of refrigerant.
• Integral torque limiter prevents over tightening
• Easy to identify pocket or screwdriver tools fit all cap types
• Caps resist cru shing and removal without key.
• Yellow warning label for AC unit is included
SOURCE 1 PART NO.
DESCRIPTION
USE WITH REFRIGERANT
PKG. QTY.
MLP $
S1-NG-R22 10PK
S1-NG-R22 2PK
S1-NG-R22 SDT
S1-NP-R410 10PK
S1-NP-R410 2PK
S1-NP-R410 SDT
REFRIGERANT LOCKING CAP, GREEN
REFRIGERANT LOCKING CAP, GREEN
SCREWDRIVER FOR REFRIGERANT LOCKING CAP, GREEN
REFRIGERANT LOCKING CAP, PINK
REFRIGERANT LOCKING CAP, PINK
SCREWDRIVER FOR REFRIGERANT LOCKING CAP, PINK
R-22
R-22
—
R-410
R-410
—
10
2
—
10
2
—
138.61
29.86
28.39
138.61
29.86
28.39
255
SOURCE 1 REFRIGERANT LINESETS
Insulated Copper Tube With EZ Pull Insulation
Features:
•
•
•
•
•
•
Currently in use in the US market
Meets ASTM E84 for smoke and fire (25/50)
Superior tear resistance
“Rugged” exterior allows for easier installation on the line set
UV Resistant
R410 A Approved
SOURCE 1 PART NO.
LIQUID
SUCTION
INSULATION
LENGTH
S1-52647150015H
S1-52647150020H
S1-52647150025H
S1-52647150030H
S1-52647150035H
S1-52647150050H
S1-52647150060H
S1-52647150100H
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
S1-52647151015H
S1-52647151020H
S1-52647151025H
S1-52647151030H
S1-52647151035H
S1-52647151050H
S1-52647151060H
S1-52647151100H
S1-52647152015H
S1-52647152020H
S1-52647152025H
S1-52647152030H
S1-52647152035H
S1-52647152050H
S1-52647152060H
S1-52647152100H
S1-52647153015H
S1-52647153020H
S1-52647153025H
S1-52647153030H
S1-52647153035H
S1-52647153050H
S1-52647153060H
S1-52647153100H
S1-52647154015H
S1-52647154020H
S1-52647154025H
S1-52647154030H
S1-52647154035H
S1-52647154050H
S1-52647154060H
S1-52647154100H
S1-52647155015H
S1-52647155020H
S1-52647155025H
S1-52647155030H
S1-52647155035H
S1-52647155050H
S1-52647155060H
S1-52647155100H
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
Note1: REFER T O WEEKLY COMMODITY PRICE SHEET FOR MLP
256
MLP $
15
20
25
30
35
50
60
100
QUANTITY PER
MASTER CARTON
12
12
12
12
12
8
6
8
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
15
20
25
30
35
50
60
100
15
20
25
30
35
50
60
100
15
20
25
30
35
50
60
100
15
20
25
30
35
50
60
100
15
20
25
30
35
50
60
100
12
12
12
12
12
8
8
8
12
12
12
12
12
8
8
8
8
8
8
8
8
8
8
8
12
12
12
12
12
8
6
8
6
6
6
6
6
8
8
8
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
Straight End Without Thermostat Wire
Factory produced linesets provide contractors with the advantage of an installation “kit” that is fast, efficient and economical to install
versus field fabrication of the lineset.
Materials:
Copper Tubing: The designation is alloy UNS 12200 and referred to as DHP. The DHP stands for a phosphorus deoxidized copper
with a high residual phosphorus range of .015% to .040%. The copper content is 99.9% copper. The copper tubing is produced in
compliance with specification ASTM B 280-98 as defined for the field installation of air conditioning and refrigeration service tube. The
tubing is fully annealed to the soft temper designation of 060.
Insulation: The insulation is a flexible, closed cell and lightweight elastomeric material designed for insulating cooling and heating
lines. The insulation is produced in compliance with specification ASTM C 534-88. The service temperature range is from –70°F to
257°F. The insulation has a thermal conductivity K value of .25 at the mean temperature of 75°F in accordance with test method
ASTM C 177. The insulation is weather and ultraviolet resistant.
SOURCE 1 PART NO.
LIQUID
SUCTION
INSULATION
LENGTH
S1-52639400020 *
S1-52639400025 *
S1-52639400030 *
S1-52639400035 *
S1-52639400040 *
S1-52639400050 *
S1-52639401020 *
S1-52639401025 *
S1-52639401030 *
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
5/8”
5/8”
5/8”
5/8”
5/8”
5/8”
3/4”
3/4”
3/4”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
20’
25’
30’
35’
40’
50’
20’
25’
30’
QUANTITY PER
MASTER CARTON
12
12
12
12
12
8
12
12
12
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
S1-52639401035 *
S1-52639401040 *
S1-52639401050 *
S1-52639402020 *
S1-52639402025 *
S1-52639402030 *
S1-52639402035 *
S1-52639402040 *
S1-52639402050 *
S1-52639403020 *
S1-52639403025 *
S1-52639403030 *
S1-52639403035 *
S1-52639403040 *
S1-52639403050 *
S1-52639404020 *
S1-52639404025 *
S1-52639404030 *
S1-52639404035 *
S1-52639404040 *
S1-52639404050 *
S1-52639405020 *
S1-52639405025 *
S1-52639405030 *
S1-52639405035 *
S1-52639405040 *
S1-52639405050 *
S1-52639406020 *
S1-52639406025 *
S1-52639406030 *
S1-52639406035 *
S1-52639406040 *
S1-52639406050 *
S1-52639407020 *
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/4”
3/4”
3/4”
7/8”
7/8”
7/8”
7/8”
7/8”
7/8”
1-1/8”
1-1/8”
1-1/8”
1-1/8”
1-1/8”
1-1/8”
5/8”
5/8”
5/8”
5/8”
5/8”
5/8”
3/4”
3/4”
3/4”
3/4”
3/4”
3/4”
7/8”
7/8”
7/8”
7/8”
7/8”
7/8”
1-1/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
1/2”
1/2”
1/2”
1/2”
1/2”
1/2”
1/2”
1/2”
1/2”
1/2”
1/2”
1/2”
1/2”
1/2”
1/2”
1/2”
1/2”
1/2”
1/2”
35’
40’
50’
20’
25’
30’
35’
40’
50’
20’
25’
30’
35’
40’
50’
20’
25’
30’
35’
40’
50’
20’
25’
30’
35’
40’
50’
20’
25’
30’
35’
40’
50’
20’
12
12
8
12
12
12
12
12
8
5
5
5
5
5
5
12
12
12
12
8
8
12
12
12
12
8
8
12
12
12
12
8
8
5
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
S1-52639407025 *
S1-52639407030 *
S1-52639407035 *
S1-52639407040 *
S1-52639407050 *
S1-52639486020
S1-52639486025
S1-52639486030
S1-52639486035
S1-52639486040
S1-52639486050
S1-52639487020
S1-52639487025
S1-52639487030
S1-52639487035
S1-52639487040
S1-52639487050
S1-52639488020
3/8”
3/8”
3/8”
3/8”
3/8”
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
1-1/8”
1-1/8”
1-1/8”
1-1/8”
1-1/8”
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
7/8"
1/2”
1/2”
1/2”
1/2”
1/2”
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
25’
30’
35’
40’
50’
20'
25'
30'
35'
40'
50'
20'
25'
30'
35'
40'
50'
20'
5
5
5
5
5
5
5
5
5
6
6
6
8
5
6
5
6
5
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
257
MLP $
SOURCE 1 REFRIGERANT LINESETS
Straight End Without Thermostat Wire
SOURCE 1 PART NO.
LIQUID
SUCTION
INSULATION
LENGTH
S1-52639488025
S1-52639488030
S1-52639488035
S1-52639488040
S1-52639488050
S1-52639489020
S1-52639489025
S1-52639489030
S1-52639489035
S1-52639489040
S1-52639489050
S1-52642344020 *
S1-52642344025 *
S1-52642344030 *
S1-52642344035 *
S1-52642344040 *
S1-52642344050 *
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8
3/8
3/8
3/8
3/8
3/8
7/8"
7/8"
7/8"
7/8"
7/8"
1-1/8"
1-1/8"
1-1/8"
1-1/8"
1-1/8"
1-1/8"
5/8
5/8
5/8
5/8
5/8
5/8
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
1
1
1
1
1
1
S1-52642345020 *
S1-52642345025 *
S1-52642345030 *
S1-52642345035 *
S1-52642345040 *
S1-52642345050 *
S1-52642346020 *
S1-52642346025 *
S1-52642346030 *
S1-52642346035 *
S1-52642346040 *
S1-52642346050 *
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/4
3/4
3/4
3/4
3/4
3/4
7/8
7/8
7/8
7/8
7/8
7/8
1
1
1
1
1
1
1
1
1
1
1
1
MLP $
25'
30'
35'
40'
50'
20'
25'
30'
35'
40'
50'
20
25
30
35
40
50
QUANTITY PER
MASTER CARTON
6
5
6
5
6
5
5
5
5
5
6
6
6
6
6
6
6
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
20
25
30
35
40
50
20
25
30
35
40
50
6
6
6
6
6
6
6
6
6
6
6
6
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
* Note: If a 90-degree bend in one end of the suction line is desired, add a B to the end of the part number when placing order (not available for linesets
with thermostat wire).
Note1: REFER TO WEEKLY COMMODITY PRICE SHEET FOR MLP
Lineset Han-Klips
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-52642278000
HAN-KLIP
See Note1 Below
Note1: REFER T O WEEKLY COM M ODITY PRICE SHEET FOR MLP
REFRIGERANT LINE COMPONENTS
Tubing Insulation
SOURCE 1 PART NO.
DESCRIPTION
ID
WALL
LENGTH
MLP $
S1-7-121-18
S1-7-1212
S1-7-121-38
S1-7-1234
S1-7-1238
S1-7-1258
S1-7-1278
S1-7-3858
Tubing Insulation
Tubing Insulation
Tubing Insulation
Tubing Insulation
Tubing Insulation
Tubing Insulation
Tubing Insulation
Tubing Insulation
1-1/8"
1/2"
1-3/8"
3/4"
3/8"
5/8"
7/8"
5/8"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
3/8"
150'
480'
120'
378'
594'
378'
288'
426'
246.36
479.25
217.86
321.57
505.68
388.96
308.61
353.96
258
MINISPLIT REFRIGERANT LINESETS
Source 1 Minisplit Refrigerant Linesets
Features:
• Both lines insulated
• With flare nuts
SOURCE 1 PART NO.
LIQUID
SUCTION
INSULATION
LENGTH
QUANTITY PER MASTER CARTON
MLP $
S1-52642437015
S1-52642437020
S1-52642437025
S1-52642437030
S1-52642437035
S1-52642437050
S1-52642438015
S1-52642438020
S1-52642438025
S1-52642438030
S1-52642438035
S1-52642438050
S1-52642439015
S1-52642439020
S1-52642439025
S1-52642439030
S1-52642439035
S1-52642439050
S1-52642440015
S1-52642440020
S1-52642440025
S1-52642440030
S1-52642440035
S1-52642440050
S1-52642441015
S1-52642441020
S1-52642441025
S1-52642441030
S1-52642441035
S1-52642441050
S1-52642442015
S1-52642442020
S1-52642442025
S1-52642442030
S1-52642442035
S1-52642442050
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
1/2”
1/2”
1/2”
1/2”
1/2”
1/2”
5/8”
5/8”
5/8”
5/8”
5/8”
5/8”
3/4”
3/4”
3/4”
3/4”
3/4”
3/4”
5/8”
5/8”
5/8”
5/8”
5/8”
5/8”
3/4”
3/4”
3/4”
3/4”
3/4”
3/4”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
15’
20’
25’
30’
35’
50’
15’
20’
25’
30’
35’
50’
15’
20’
25’
30’
35’
50’
15’
20’
25’
30’
35’
50’
15’
20’
25’
30’
35’
50’
15’
20’
25’
30’
35’
50’
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
259
TP Series
Designed to quietly remove condensate from ductless mini split air conditioning equipment
Features:
• Automatically operates when water fills its remote collection reservoir and activates a float operated switch
• Safety overflow switch with NO and NC option
• External test/run switch
• Double insulated
• Easy to replace pump tube - no tools required
• Clear, hinged pump head cover for easy inspection and servicing
• Compact, lightweight design
• IP52
• CE
• 2 m suction lift
• 14 m lift
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-553676
TPR AUTOMATIC CONDENSATE REMOVAL PUMP 230V 50 HZ
562.54
MINISPLIT CONDENSATE HANDLING
Aspen Maxi Orange 100-250V Condensate Pump
Need a lift? Our Aspen line is quiet, reliable and versatile. Available in 2 configurations our Maxi pumps can put
unwanted condensate in its place. The Maxi Orange comes with 2 different reservoir options and can be remote
mounted for easy access. Can be used with units up to 5 tons.
Specifications:
• Sound Level - 35dB(A)
• Pump Length - 4.875"
• Dry Contact Rating - 3A NO/NC
• Pump Width - 1.75"
• Voltage – 100-250v
• Pump Height - 2.625"
• Amperes - .15-.28
• Capacity - 10 GPH @ Zero Head / 3.8 GPH @
50' Head
• Watts - 21
• Max BTUs - 60000
• Remote Reservoir - Y
• Max Head in Feet - 50
• Plenum Rated – N
• Cable Length - 6'
• Max Temperature - N/A
• Max Suction Lift - 4'
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ASP-MAXO-UNI
Aspen Maxi Orange Univ Condensate Pump Kit
318.61
Aspen Mini Aqua 100-230V Condensate Pump
Need a lift? Our Aspen line is quiet, reliable and versatile. Available in all shapes and sizes our Mini pumps can
put unwanted condensate in its place. With it's ultra slim profile the Mini Aqua fits right inside the evaporator for
easy installation.
Specifications:
• Max Suction Lift - 3'
• Sound Level - 25dB(A)
• Dry Contact Rating - 3A NO/NC
• Capacity - 3.7 GPH @ Zero Head / 0.8 GPH @
• Voltage - 100-250
33' Head
• Amperes - .15 MAX
• Max BTUs - 24000
• Watts - 16
• Remote Reservoir - Y
• Plenum Rated - N
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ASP-MA-UNI
MINI AQUA CONDENSATE PUMP KIT
298.75
260
Aspen Mini Lime 100-250V Condensate Pump
put unwanted condensate in its place. Available in three lineset cover styles, the Mini Lime is perfect when
putting the pump in the ceiling or wall just isn''t possible.
Specifications:
33'' Head
• Max BTUs - 30000
• Max Suction Lift - N/A
•
•
•
•
•
•
•
•
Sound Level - 25.5dB(A)
Dry Contact Rating - 3A NO/NC
Voltage - 100-250
Amperes - .16
Watts - 13.5
Remote Reservoir - N
Plenum Rated - N
Cable Length - 6''
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ASP-MLF-UNI
MINI LIME CONDENSATE PUMP KIT
358.5
Aspen Mini White 100-250V Condensate Pump
put unwanted condensate in its place. The Mini White mounts directly below the evaporater making it great for
retrofit jobs and easy maintenance.
Specifications:
• Pump Width - 2"
33'' Head
• Max BTUs - 30000
• Max Suction Lift - N/A
•
•
•
•
•
•
•
•
Sound Level - 22dB(A)
Dry Contact Rating - 3A NO/NC
Voltage - 100-250
Amperes - .18
Watts - 15
Remote Reservoir - Y
Plenum Rated - N
Cable Length - 6''
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ASP-MW-UNI
MINI WHITE CONDENSATE PUMP KIT
298.75
Clearvue KubeTM Minisplit Condensate Pump
SOURCE 1 PART NO.
DESCRIPTION
ORDER MULTIPLE
MLP $
S1-IQP-KUBE
S1-IQP-KUBE-SHROUD
MINISPLIT CONDENSATE PUMP
MINISPLIT CONDENSATE PUMP WITH SHROUD
6
6
245.07
347.07
261
ClearvueTM Mini Ductless System Condensate Pump
SOURCE 1 PART NO.
DESCRIPTION
ORDER MULTIPLE
MLP $
S1-CVMINI
CLEARVUE MINI PUMP - 120/230V
6
253.68
ClearvueTM Tube
Cl ear, 3/4” I.D. schedul e 40 PVC ideal for installi ng as condensate drain lines i n other areas where seeing the i nside of the tubing i s hel pful .
SOURCE 1 PART NO.
DESCRIPTION
ORDER MULTIPLE
MLP $
S1-CV-TUBE
CLEARVUE 3/4" ID TUBE - 5 FT LENGTH
5
51.00
16mm (5/8") Drain Hose 20 Retail Pack
Standard weight drain hose in retail pack
Specifications:
• Inside Diameter - 5/8"
• Outside Diameter • Material • Length - 20'
• Insulated - N
• UV Protection - N
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-DH-16S
5/8" I.D. DRAIN HOSE, 20'
23.46
DiversiTech Minisplit Condensate Drain Line
A unique drain line for minisplit units. This large diameter drain line is typical for minisplit installations. Furnished
in 160 feet lengths with cut marks every 3.28 feet.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-230-DL16
S1-230-DL20
5/8” ID MINISPLIT DRAIN LINE
3/4” ID MINISPLIT DRAIN LINE
160’/ROLL
160’/ROLL
114.32
119.29
262
SS610E Overflow Switch for Mini Split Systems
SS610E is specially designed for use in Mini Split systems. Its small Sensor can easily fit in the confined internal
spaces of most units. It can also be installed directly in the Drain Pan or clipped to the unit’s Coils. SS610E’s
CPU unit is housed in an attractive casing that can be mounted directly to the side of the unit. Uses power from
A/C unit so no batteries are required. The Electronic Condensate Overflow Switch contains low power
consuming, state-of the-art microelectronics. SS610E’s logic circuit continuously samples the probes for water.
If water is detected, the circuit determines if the condition is transient or permanent. If permanent, the system
will be shutdown. Onboard LED’s indicate the condition of the unit.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-SS610E
OVERFLOW SWITCH FOR MINI SPLIT SYSTEMS
147.14
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-EZT180
TRAP,CONDENSATE,WATERLESS,5/8" (M10)
22.39
Trap,Condensate,Waterless,5/8" (M10)
MINISPLIT MOUNTING ACCESSORIES
DiversiTech 45º Flat Bend
45º flat bends are used to route the SpeediChannel ™ around an obstacle. Each bend is individually
packed, and is furnished complete with stainless steel screws.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-230-FB453
S1-230-FB454
S1-230-FB456
3” 45 DEGREE FLAT BEND
10
10
10
21.04
39.14
44.18
DiversiTech 90º Flat Bend
90º flat bends are used to route the SpeediChannel ™ around an obstacle. Each bend is individually
packed, and is furnished complete with stainless steel screws.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-230-FB3
S1-230-FB4
S1-230-FB6
3” 90 DEG FLAT BEND
10
10
10
21.04
39.14
44.18
DiversiTech 90º Inside Elbow
90º inside elbows are used to route the SpeediChannel ™ around an inside corner. Each elbow is individually packed, and is furnished
complete with stainless steel screws.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-230-EB3
S1-230-EB4
S1-230-EB6
3” 90 DEGREE INSIDE ELBOW
10
10
10
18.82
39.89
48.00
263
DiversiTech 90º Long Radius Bend
90º long radius flat bends are used to route the SpeediChannel ™ around an obstacle. T he long radius of the elbow allows a gentle
bending radius on the copper line set. Each elbow is individually packed, and is furnished complete with stainless steel screws.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-230-LFB3
S1-230-LFB4
S1-230-LFB6
3” 90 DEG LONG RADIUS BEND
10
10
10
26.43
31.79
45.39
DiversiTech 90º Outside Elbow
90º outside elbows are used to route the SpeediChannel ™ around an outside corner. Each elbow is individually packed, and is
furnished complete with stainless steel screws.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-230-EIN3
S1-230-EIN4
S1-230-EIN6
3” 90 DEGREE OUTSIDE ELBOW
10
10
10
18.82
39.89
48.00
DiversiTech Cap
Used to cap the end of a SpeediChannel ™ run. Easily snaps into the end of the SpeediChannel ™.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-230-DC3
S1-230-DC4
S1-230-DC6
3” CAP
4” CAP
6” CAP
10
10
10
10.57
12.21
12.43
DiversiTech Duct End
T he duct end is used to terminate a run of SpeediChannel ™ to a small opening – just large enough for the line set and condensate
drain line to pass through. Gives a neat/clean installation.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-230-DE3
S1-230-DE4
3” DUCT END
4” DUCT END
10
10
12.04
19.07
6” DUCT END
10
21.14
S1-230-DE6
DiversiTech Flat Wall Escutcheon
Typically used to cover a rough opening in a soffit, wall, or ceiling penetration. One side of the escutcheon is flat to allow for a
SpeediChannel ™ run going along a wall, and penetrating through an adjacent wall or ceiling. This is the most common type of wall
™
penetration. Furnished in two parts, the escutcheon easily snaps onto the SpeediChannel .
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-230-FR3
S1-230-FR4
S1-230-FR6
3” FLAT WALL ESCUTCHEON
10
10
10
9.86
11.64
12.71
264
DiversiTech Flex Joint
™
™
An accordion style piece of SpeediChannel , the flex joint can be extremely flexible routing a SpeediChannel system around
virtually any type of obstacle. Each joint is 20” long and can be combined together for longer flex runs. Unlike competitor systems, the
™
DiversiTech flex joint does NOT require the use of a union coupling.The DiversiTech flex joint slides tightly inside the SpeediChannel
sy stem.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-230-FJ3
S1-230-FJ4
3” FLEX JOINT
4” FLEX JOINT
10
10
14.68
29.18
DiversiTech Minisplit Drain Adapters
Minisplit fan units — either ceiling cassettes or wall cassettes — typically have a unique (metric) drain line fitting. DiversiT ech’s
adapters convert this metric fitting to standard drain line tubing sizes.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-230-DLF16
S1-230-DLF18
S1-230-DLF20
S1-230-DLF25
S1-230-DLF32
S1-230-DLFY
16 MM MINISPLIT DRAIN LINE ADAPTER (PACK OF 1)
MINISPLIT DRAIN LINE WYE (PACK OF 1)
10
10
10
10
10
10
9.89
9.89
9.89
8.86
8.86
2.46
DiversiTech Mounting Blocks
Used as mounting bases when condensing units must be bolted down. Available in three lengths. End caps are also available for
aesthetics. Furnished complete with mounting bolts. Maximum load capacity is 900 pounds per mounting block. Installation
temperature range from -4°F (-20°C) to 140°F (60°C). Mount Blocks fit all mini-split condensing units with a unique sliding rail feature.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-230-MB14W
S1-230-MB17W
S1-230-MB36W
S1-230-MBCW
14” MOUNTBLOCK (WHITE) PACK OF 2
MOUNTBLOCK END CAP (WHITE) PACK OF 4
6
6
1
25
27.14
31.50
72.50
11.89
*Sol d by Case / M LP per Pack
DiversiTech Reducer Coupling
Used for joining two pieces of SpeediChannel ™ — each cover being a different size. Each coupling is individually packed, and is
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-230-TC34
S1-230-TC46
3” x 4” REDUCER COUPLING
4” x 6” REDUCER COUPLING
10
10
14.14
18.61
DiversiTech SpeediChannel™
T he DiversiTech SpeediChannel ™ is available in three widths, all in 6-1/2 feet lengths.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-230-D3
S1-230-D4
S1-230-D6
3” SPEEDICHANNEL
4” SPEEDICHANNEL
6” SPEEDICHANNEL
6
6
5
50.71
72.36
96.07
265
DiversiTech SpeediChannel™ Accessories
A variety of accessories that are complementary or required for installing DiversiT ech’s SpeediChannel ™ system.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-230-DCLIP
S1-230-DSCREW
S1-WTB11C
SPEEDICLIP
SPEEDICHANNEL SCREW
BLACK WIRE TIES – 11”
50
100
100
24.71
35.86
21.21
DiversiTech T-Joint
Used for creating a tee connection between three pieces of SpeediChannel™ – all covers being the same size. The tee can be
combined with the reducing coupling to join different sizes of SpeediChannel ™. Each tee is individually packed, and is furnished
complete with stainless steel screws.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-230-TJ4
S1-230-TJ6
4” T-JOINT
6” T-JOINT
10
10
81.57
93.11
DiversiTech Union Coupling
Used for joining two pieces of SpeediChannel ™ — each cover being the same size. Each coupling is individually packed, and is
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-230-CP3
S1-230-CP4
S1-230-CP6
3” UNION COUPLING
4” UNION COUPLING
6” UNION COUPLING
10
10
10
7.79
15.39
18.61
DiversiTech Wall Escutcheon
Typically used to cover a rough opening in a wall or ceiling penetration. The hole in the escutcheon is centered to allow for a free
standing SpeediChannel ™ to penetrate through a wall or ceiling. This is the fairly un-common type of wall or ceiling penetration. Check
™
carefully, as you may need the Flat Wall Escutcheon Furnished in two parts, the escutcheon easily snaps onto the SpeediChannel .
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-230-WR3
S1-230-WR4
S1-230-WR6
3” WALL ESCUTCHEON
10
10
10
11.04
12.96
14.75
DiversiTech Wall Penetration
Wall sleeves and penetration covers are used to transition from the SpeediChannel™ system to a
through wall penetration. The wall sleeve creates a neat hole through the wall, and the line set is
covered by the wall cover. DiversiTech’s wall covers are designed to allow for easy installation even after the line set has been installed. A unique hooking and fastening arrangement allows for
quick and easy installation. Each wall cover is individually packed, and is furnished complete with
stainless steel screws to attach the wall cover to the base. Three screws (not included) are needed
to fasten the wall cover to whatever type of wall construction the system is being installed on.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-230-WC3
S1-230-WC4
S1-230-WC6
S1-230-WS2
3” WALL PENETRATION COVER
2-1/2” WALL SLEEVE
10
10
10
10
23.07
39.36
49.00
17.29
266
Fortress 12 Wall Duct Kit
Complete kit! The Fortress LDK Wall Duct Kit includes 12 feet of duct and essential fittings. Everything to quickly hide and protect the
lineset for a typical AC installation in one box
Specifications:
• Material – PVC
• Color – White
• Paintable - Y
• Temp Range - 0°-180°
SOURCE 1 PART NO.
DESCRIPTION
DUCT WIDTH
MLP $
S1-LDK-122-W
S1-LDK-92-W
12' LINESET COVER KIT, WHITE
12' LINESET COVER KIT, WHITE
4.5"
3.5"
148.86
114.50
Piping Riser
Provides simple and secure mounting for small and large piping systems, ductwork runs, cable trays and smaller equipment such as
condensers. Linear track offers adjustble mounting. Manufactured from exterior grade materials.
Specifications:
• Material - PVC
• Coating - N/A
• Capacity - 397lb.
• Length - 17.75"
• Width - 4"
• Height - 3.75"
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-PR-351N-M
POLYMER PIPING RISER
19.86
Telescoping Wall Sleeve, 2 1/2" x 5" - 7 3/4"
Used to provi de a seal when penetrating wall s. ID - 2 1/2" OD - 2 7/8"
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-NFP-75
TELESCOPING WALL SLEEVE
13.96
Underslab Condenser Bracket
Made from heavy duty steel with powdercoat finish. This stand raises the condenser up to 12" above a flat surface. Each leg is
independently adjustable for uneven surfaces and has anti slip rubber feet.
Specifications:
• Material - Steel
• Coating - Powdercoat
• Length - 31.75"
• Width - 15"
• Height - 12.5"
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CNG
UNDERSLAB CONDENSER BRACKET
171.39
Wall Condenser Bracket
Made from heavy duty steel with powdercoat finish. The WBB300 features a sliding cross bar for exceptional equiptment width range
and a level for added convenience.
Specifications:
• Material - Steel
• Coating - Powdercoat
• Length - 22"
• Width - 33.5"
• Height - 18"
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-WBB300
WALL MOUNT CONDENSER BRACKET
100.57
267
JMF COMPANY COPPER REFRIGERATION TUBING
Soft Refrigeration Coils
SOURCE 1 PART NO.
SIZE (INCHES)
LENGTH (FEET)
WEIGHT/COIL
WALL THICKNESS
MLP $
S1-00708121000
S1-00708122000
S1-00708123000
S1-00708124000
S1-00708125000
S1-00708126000
S1-00708127000
S1-00708128000
S1-00708129000
S1-00708130000
S1-00708131000
S1-00708132000
S1-00708147000
S1-00708148000
S1-00708149000
S1-00708150000
S1-00708151000
S1-00708152000
S1-00708153000
S1-00708154000
1/8
3/16
1/4
5/16
3/8
1/2
5/8
3/4
7/8
1-1/8
1-3/8
1-5/8
1/4
5/16
3/8
1/2
5/8
3/4
7/8
1-1/8
50
50
50
50
50
50
50
50
50
50
50
50
100
100
100
100
100
100
100
100
1.74
2.88
4.02
5.45
6.70
9.10
12.55
15.25
22.75
32.75
44.20
57.00
8.04
10.90
13.40
18.20
25.10
30.50
45.50
65.50
0.030
0.030
0.030
0.032
0.032
0.032
0.035
0.035
0.045
0.50
0.055
0.060
0.030
0.032
0.032
0.032
0.035
0.035
0.045
0.50
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
Type ACR Hard Refrigeration Copper Tubing
SOURCE 1 PART NO.
SIZE (INCHES)
LENGTH (FEET)
WEIGHT/COIL
WALL THICKNESS
MLP $
S1-00708133000
S1-00708134000
S1-00708135000
S1-00708136000
S1-00708137000
S1-00708138000
S1-00708139000
S1-00708140000
S1-00708141000
S1-00708142000
S1-00708143000
S1-00708144000
3/8
1/2
5/8
3/4
7/8
1-1/8
1-3/8
1-5/8
2-1/8
2-5/8
3-1/8
4-1/8
20
20
20
20
20
20
20
20
20
20
20
20
2.52
3.96
5.70
7.24
9.10
13.10
17.68
22.80
35.00
49.60
66.60
107.60
0.035
0.040
0.042
0.045
0.045
0.050
0.055
0.060
0.070
0.080
0.090
0.110
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
COPPER FITTINGS
45 Degree Elbow
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-W03005
S1-W03012
S1-W03021
S1-W03026
S1-W03030
S1-W03034
S1-W03044
S1-W03050
45 DEG ELBOW 1/4
45 DEG ELBOW 3/8
45 DEG ELBOW 1/2
45 DEG ELBOW 5/8
45 DEG ELBOW 3/4
45 DEG ELBOW 7/8
45 DEG ELBOW 1-1/8
45 DEG ELBOW 1-3/8
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
Note1: REFER T O WEE KLY COM MODIT Y P RICE SHEET FOR MLP
45 Degree Street Elbow
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-W03312
S1-W03321
S1-W03326
S1-W03330
S1-W03334
S1-W03344
S1-W03350
45 DEG STREET ELBOW 3/8
45 DEG STREET ELBOW 1-1/8
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
268
COPPER FITTINGS
90 Degree Elbow
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-W02003
S1-W02009
S1-W02017
S1-W02028
S1-W02034
S1-W02047
S1-W02084
S1-WB01622
90 DEG ELBOW 1/4
90 DEG ELBOW 3/8
90 DEG ELBOW 1/2
90 DEG ELBOW 3/4
90 DEG ELBOW 7/8
90 DEG ELBOW 1-1/8
90 DEG ELBOW 1-3/8
90 DEG ELBOW 5/8
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
1.37
90 Degree Long Rad Elbow
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-W02055
S1-W02715
S1-W02716
S1-W02717
S1-W02722
S1-W02728
S1-W02734
S1-W02747
90 DEG LONG RAD ELBOW 1-3/8
90 DEG LONG RAD ELBOW 1/4
90 DEG LONG RAD ELBOW 1-1/8
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
90 Degree Long Rad Street Elbow
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-W02350
S1-W02809
S1-W02817
S1-W02822
S1-W02828
S1-W02834
S1-W02847
S1-WE503L-1/4
90 DEG LONG RAD STREET ELBOW 1-3/8
90 DEG LONG RAD STREET ELBOW 3/8
90 DEG LONG RAD STREET ELBOW 1-1/8
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
90 Degree Street Elbow
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-W02312
S1-W02321
S1-W02326
S1-W02330
S1-W02344
S1-W02384
S1-WB01654
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
4.35
Bushing
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-W01712
S1-W01715
S1-W01725
S1-W01737
BUSHING 1/2 x 3/8
BUSHING 5/8 x 1/2
BUSHING 7/8 x 3/4
BUSHING 1-1/8 x 7/8
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
Cap Tube
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-W07007
S1-W07008
S1-W07009
CAP TUBE 5/8
CAP TUBE 3/4
CAP TUBE 7/8
See Note1 Below
See Note1 Below
See Note1 Below
269
COPPER FITTINGS
Copper Suction Line P-Traps
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-W60999
S1-W61000
S1-W61001
S1-W61008
P-TRAP, SUCTION LINE, COPPER, 5/8 INCH
P-TRAP, SUCTION LINE, COPPER, 7/8"
P-TRAP, SUCTION LINE, COPPER, 1-1/8"
P-TRAP, SUCTION LINE, COPPER, 3/4"
See Note1 Below
45.2
68.68
57.60
Female Adapter
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-W01231
FEMALE ADAPTER, 5/8 x 1/2
S1-W01246
S1-W01271
FEMALE ADAPTER 7/8 x 3/4
FEMALE ADAPTER 1-3/8 x 1-1/4
Refer to weekly commodity
sheet
See Note1 Below
See Note1 Below
Male Adapter
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-W01131
S1-W01146
S1-W01171
MALE ADAPTER 5/8 x 1/2
MALE ADAPTER 7/8 x 3/4
MALE ADAPTER 1-3/8 x 1-1/4
See Note1 Below
See Note1 Below
See Note1 Below
Reducing Coupling
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-W01011
S1-W01019
S1-W01023
S1-W01025
S1-W01029
S1-W01030
S1-W01035
S1-W01036
S1-W01049
S1-W01056
REDUCING COUPLING 3/8 x 1/4
REDUCING COUPLING 1-1/8 x 7/8
REDUCING COUPLING 1-3/8 x 1-1/8
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
Rolled Stop Coupling
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-W01003
S1-W01009
S1-W01017
S1-W01022
S1-W01028
S1-W01034
S1-W01047
S1-W01055
ROLLED STOP COUPLING 1/4
ROLLED STOP COUPLING 1-1/8
ROLLED STOP COUPLING 1-3/8
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
Tee
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-W04000
S1-W04001
S1-W04006
S1-W04017
TEE 3/8
TEE 1/2
TEE 5/8
TEE 3/4
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
S1-W04031
S1-W04048
S1-W04068
TEE 7/8
TEE 1-1/8
TEE 1-3/8
See Note1 Below
See Note1 Below
See Note1 Below
270
COPPER FITTINGS
Tube Strap
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-A01366
S1-A02574
S1-A02614
S1-A02708
TUBE STRAP 1/2
TUBE STRAP 7/8
TUBE STRAP 1-1/8
TUBE STRAP 2-1/8"
0.71
1.14
1.21
1.75
Union
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-W08002
S1-W08003
S1-W08004
UNION 1/2
UNION 5/8
UNION 7/8
See Note1 Below
See Note1 Below
See Note1 Below
271
COPPER FITTINGS
Union
JMF COMPANY COPPER REFRIGERATION TUBING
JMF COMPANY BRASS FLARE NUTS
Short Forged Nuts for Mini-Split Line Sets
SOURCE 1 PART NO.
DESCRIPTION
FLARE SIZE
STD. PACK
MLP $
S1-5219206989802
S1-5219208989802
S1-5219210989802
S1-5219204989802
NUT,FLARE,MINISPLT LINESET,3/8"
3/8"
1/2"
5/8"
1/4"
10
10
10
10
2.36
3.25
6.18
3.25
272
TEFLON TAPE
Made of pure white T eflon. Non-toxic. For use with chemicals, solvents, oxygen, and on food lines. Withstands up to 2000 psi of
pressure.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-6-733
S1-6-734
S1-6-735
S1-6-736
TEFLON TAPE – 1/2” x 520”
100
100
100
100
1.21
1.00
2.36
1.86
MALLEABLE BLACK IRON PIPE FITTINGS
Black Pipe Cut Lengths
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-02321587084
S1-02321587085
WITH THREAD, 1/2 x 36 (M5)
13.96
17.64
S1-02321587092
S1-02321587107
S1-02321587117
S1-02321587118
S1-02321587119
WIH THREAD, 1/2" X 60" (M5)
22.54
16.93
20.46
11.82
31.68
273
Black Pipe Nipples
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-02321587043
S1-02321587044
S1-02321587045
S1-02321587046
S1-02321587047
S1-02321587048
S1-02321587049
S1-02321587050
S1-02321587051
S1-02321587052
S1-02321587053
S1-02321587054
S1-02321587055
S1-02321587056
S1-02321587057
S1-02321587058
S1-02321587059
S1-02321587060
S1-02321587061
S1-02321587062
S1-02321587063
S1-02321587064
S1-02321587065
S1-02321587066
S1-02321587067
S1-02321587068
S1-02321587069
S1-02321587070
S1-02321587071
S1-02321587072
S1-02321587073
S1-02321587074
S1-02321587075
S1-02321587076
S1-02321587077
S1-02321587078
S1-02321587079
S1-02321587080
S1-02321587081
S1-02321587082
S1-02321587083
S1-02321587086
S1-02321587087
S1-02321587088
S1-02321587089
S1-02321587090
S1-02321587094
S1-02321587095
S1-02321587096
S1-02321587097
1/2 x CL
1/2 x 2
1/2 x 3
1/2 x 4
1/2 x 5
1/2 x 6
1/2 x 8
1/2 x 10
1/2 x 12
3/4 x CL
3/4 x 2
3/4 x 3
3/4 x 4
3/4 x 5
3/4 x 6
3/4 x 8
3/4 x 10
3/4 x 12
1 x CL
1x2
1x3
1x4
1x5
1x6
1x8
1 x 10
1 x 12
1-1/4 x CL
1-1/4 x 2
1-1/4 x 3
1-1/4 x 4
1-1/4 x 5
1-1/4 x 6
1-1/4 x 8
1-1/4 x 10
1-1/4 x 12
1/2 x 1.5 (M25)
1/2 x 2.5 (M25)
1/2 x 3.5 (M25)
1/2 x 4.5 (M25)
1/2 x 5.5 (M25)
3/4 x 1.5 (M25)
3/4 x 2.5 (M25)
3/4 x 3.5 (M25)
3/4 x 4.5 (M25)
3/4 x 5.5 (M25)
1 x 2.5 (M25)
1 x 3.5 (M25)
1 x 4.5 (M25)
1 x 5.5 (M25)
1.04
1.04
1.21
1.46
1.75
1.93
3.46
4.18
4.96
1.18
1.29
1.50
1.79
2.25
2.54
4.32
4.93
5.46
1.75
1.89
2.00
2.50
2.93
3.50
5.68
6.64
7.61
1.11
1.21
1.50
1.89
2.39
2.75
3.89
4.64
5.32
1.04
1.21
1.46
1.75
1.93
1.32
1.46
1.79
2.25
2.54
1.39
1.75
2.04
2.43
S1-02321587109
S1-02321587110
S1-02321587114
NIPPLE,BLK IRON,1/2" ASSORTMENT OF 66
NIPPLE,BLK IRON,3/4" ASSORTMENT OF 66
1/2 x 7 (M25)
116.89
142.18
3.25
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-02321587011
S1-02321587012
S1-02321587013
S1-02321587014
1/2
3/4
1
1-1/4
2.57
3.14
3.96
6.93
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-02321587020
S1-02321587021
S1-02321587022
S1-02321587023
1/2
3/4
1
1-1/4
3.32
5.11
2.29
3.79
Malleable Iron 45 Ells
Malleable Iron 45 Street Ell
274
Malleable Iron 90 Elbows
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-02321587001
S1-02321587002
S1-02321587003
S1-02321587004
S1-02321587005
S1-02321587006
S1-02321587007
S1-02321587008
S1-02321587009
S1-02321587010
1/2
3/4
1
1-1/4
3/4 x 1/2
1 x 3/4
1 x 1/2
1-1/4 x 1
1-1/4 x 3/4
1-1/2 x 1-1/4
1.75
1.89
3.32
5.39
2.96
3.82
4.04
6.18
2.71
3.32
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-02321587015
S1-02321587016
S1-02321587017
1/2
3/4
1
3.25
3.18
4.57
S1-02321587018
1-1/4
2.82
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-02321587105
S1-02321587106
HEX, 1 x 3/4 (M50)
HEX, 3/4 x 1/2 (M50)
2.61
2.54
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-02321587038
S1-02321587039
S1-02321587040
S1-02321587041
S1-02321587042
1/2
3/4
1
1-1/4
1-1/2
1.57
2.11
2.57
1.32
1.75
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-02321587029
S1-02321587030
S1-02321587031
S1-02321587032
S1-02321587033
S1-02321587034
S1-02321587035
S1-02321587036
S1-02321587037
1/2
3/4
1
1-1/4
3/4 x 1/2
1 x 3/4
1 x 1/2
1-1/4 x 1
1-1/4 x 3/4
2.11
2.50
3.82
4.86
2.50
3.89
3.89
4.86
1.79
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-02321587098
S1-02321587099
S1-02321587100
SQUARE HEAD, 1/2 (M50)
SQUARE HEAD, 3/4 (M30)
SQUARE HEAD, 1 (M20)
1.43
1.43
1.79
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-02321587024
S1-02321587025
S1-02321587026
S1-02321587027
S1-02321587028
S1-02321587104
S1-02321587108
S1-02321587111
S1-02321587112
S1-02321587113
S1-02321587115
S1-02321587116
1/2
3/4
1
1-1/4
1-1/2
REDUCING,3/4 x 1/2 x 1/2 (M30)
TEE,REDUCING,BLK,3/4 x 3/4 x 1/2 (M20)
TEE,REDUCING,BLK,1/2 x 1/2 x 3/4 (M30)
TEE,REDUCING,BLK,1 x 3/4 x 3/4 (M15)
TEE,REDUCING,BLK,1 x 3/4 x 1/2 (M20)
TEE,REDUCING,BLK,1 x 3/4 x 1 (M15)
TEE,REDUCING,BLK,1 x 1/2 x 1 (M15)
2.07
2.89
5.11
8.61
3.79
4.64
4.50
5.11
6.00
6.39
7.07
7.07
Malleable Iron 90 Street Ell
Malleable Iron Bushings
Malleable Iron Caps
Malleable Iron Couplings
Malleable Iron Plugs
Malleable Iron Tee
275
Malleable Iron Unions With Brass Seats
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-02321587101
S1-02321587102
S1-02321587103
1/2 x 1/2 (M50)
3/4 x 3/4 (M35)
1 x 1 (M20)
6.93
8.25
10.79
PVC Pipe & Fittings
NYLON FITTINGS
Male Adapter Elbow
Barb x MIPT
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-701-026
ELBOW – 3/8 BARB x 1/2 MIPT
2
2.36
PVC CLEANOUT TEE
SOURCE 1 PART NO.
DESCRIPTION
SHIPPING MULTIPLE
MLP $
S1-510-3400
3/4" PVC CLEANOUT TEE
50
2.46
PVC DWV FITTINGS
Coupling, Reducing
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-PVC-D102-338
3 IN. x 2 IN. COUPLINGS (HUB x HUB)
20
8.82
276
PVC Pipe & Fittings
SCHEDULE 40 PVC FITTINGS
90° Street Elbow MPT x FPT
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-M412-005
S1-PVC-M412-007
1/2 Poly
3/4 Poly
50
50
1.48
1.81
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-435-074
S1-PVC-435-101
S1-PVC-435-102
S1-PVC-435-131
S1-PVC-435-211
1/2 x 3/4
3/4 x 1/2
3/4 x 1
1 x 3/4
1 x 1-1/2
50
50
50
50
25
1.07
1.07
1.40
1.40
2.79
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-435-005
S1-PVC-435-007
S1-PVC-435-010
S1-PVC-435-012
S1-PVC-435-015
S1-PVC-435-020
S1-PVC-435-025
S1-PVC-435-030
S1-PVC-435-040
S1-PVC-435-050
S1-PVC-435-060
S1-PVC-435-080
1/2
3/4
1
1-1/4
1-1/2
2
2-1/2
3
4
5
6
8
100
50
50
25
25
25
10
10
5
5
4
4
0.62
0.74
0.86
1.31
1.52
2.01
5.13
6.86
11.37
29.47
41.87
78.98
Adapter, Female, Reducing, SOCKET X FIPT
*Sold by Standard Pack / MLP per each
Adapter, Female, SOCKET X FIPT
Adapter, INSERT X SOCKET
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-474-007
S1-PVC-474-010
S1-PVC-474-015
3/4
1
1-1/2
50
50
25
2.01
2.09
3.69
Adapter, Male, MIPT X SOCKET
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-436-005
S1-PVC-436-007
S1-PVC-436-010
S1-PVC-436-012
S1-PVC-436-015
S1-PVC-436-020
S1-PVC-436-025
S1-PVC-436-030
S1-PVC-436-040
S1-PVC-436-050
S1-PVC-436-060
S1-PVC-436-080
1/2
3/4
1
1-1/4
1-1/2
2
2-1/2 x 2-1/2
3
4
5
6
8
100
50
50
25
25
25
10
10
5
5
4
4
0.49
0.53
0.94
1.15
1.52
1.97
5.83
8.54
10.88
17.90
28.33
128.82
277
PVC Pipe & Fittings
Adapter, Reducing, Male, MIPT X SOCKET
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-436-073
S1-PVC-436-074
S1-PVC-436-101
S1-PVC-436-102
S1-PVC-436-131
S1-PVC-436-132
S1-PVC-436-168
S1-PVC-436-169
S1-PVC-436-212
S1-PVC-436-213
S1-PVC-436-251
S1-PVC-436-252
S1-PVC-436-293
S1-PVC-436-341
1/2 x 3/8
1/2 x 3/4
3/4 x 1/2
3/4 x 1
1 x 3/4
1 x 1-1/4
1-1/4 x 1
1-1/4 x 1-1/2
1-1/2 x 1-1/4
1-1/2 x 2
2 x 1-1/2
2 x 2-1/2
2-1/2 x 3
3x4
100
50
50
50
50
25
25
25
25
10
10
10
10
10
0.94
0.94
0.86
1.31
2.83
3.08
3.45
3.45
4.19
4.19
4.80
7.43
8.99
14.37
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-438-071
S1-PVC-438-072
S1-PVC-438-073
S1-PVC-438-098
S1-PVC-438-101
S1-PVC-438-130
S1-PVC-438-131
S1-PVC-438-166
S1-PVC-438-167
S1-PVC-438-168
S1-PVC-438-209
S1-PVC-438-210
S1-PVC-438-211
S1-PVC-438-212
S1-PVC-438-247
S1-PVC-438-248
S1-PVC-438-249
S1-PVC-438-250
S1-PVC-438-251
S1-PVC-438-289
S1-PVC-438-290
S1-PVC-438-291
S1-PVC-438-292
S1-PVC-438-335
S1-PVC-438-336
S1-PVC-438-337
S1-PVC-438-338
S1-PVC-438-339
S1-PVC-438-420
S1-PVC-438-421
S1-PVC-438-422
S1-PVC-438-490
S1-PVC-438-532
1/2 x 1/8
1/2 x 1/4
1/2 x 3/8
3/4 x 1/4
3/4 x 1/2
1 x 1/2
1 x 3/4
1-1/4 x 1/2
1-1/4 x 3/4
1-1/4 x 1
1-1/2 x 1/2
1-1/2 x 3/4
1-1/2 x 1
1-1/2 x 1-1/4
2 x 1/2
2 x 3/4
2x1
2 x 1-1/4
2 x 1-1/2
2-1/2 x 1
2-1/2 x 1-1/4
2-1/2 x 1-1/2
2-1/2 x 2
3x1
3 x 1-1/4
3 x 1-1/2
3x2
3 x 2-1/2
4x2
4 x 2-1/2
4x3
5x4
6x4
100
100
100
50
100
100
100
25
25
25
25
25
25
25
10
10
10
10
10
10
10
10
10
10
10
10
10
10
5
5
5
5
5
1.15
1.15
1.15
1.15
0.86
1.40
1.40
2.09
2.09
2.09
2.42
2.42
2.42
2.42
3.28
3.28
3.28
3.28
3.28
4.72
4.72
4.72
4.72
5.46
5.46
5.46
5.46
5.46
12.15
12.15
12.15
23.69
44.42
Bushing, Reducing, SPIGOT X FIPT
278
PVC Pipe & Fittings
Bushing, Reducing, SPIGOT X SOCKET
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-437-073
S1-PVC-437-101
S1-PVC-437-130
S1-PVC-437-131
S1-PVC-437-166
S1-PVC-437-167
S1-PVC-437-168
S1-PVC-437-209
S1-PVC-437-210
S1-PVC-437-211
S1-PVC-437-212
S1-PVC-437-247
S1-PVC-437-248
S1-PVC-437-249
S1-PVC-437-250
S1-PVC-437-251
S1-PVC-437-287
S1-PVC-437-288
S1-PVC-437-289
S1-PVC-437-290
S1-PVC-437-291
S1-PVC-437-292
S1-PVC-437-334
S1-PVC-437-334†
S1-PVC-437-335
S1-PVC-437-336
S1-PVC-437-337
S1-PVC-437-338
S1-PVC-437-339
S1-PVC-437-420
S1-PVC-437-421
S1-PVC-437-422
S1-PVC-437-488
S1-PVC-437-490
S1-PVC-437-528
S1-PVC-437-530
S1-PVC-437-532
S1-PVC-437-534
S1-PVC-437-582
S1-PVC-437-585
1/2 x 3/8
3/4 x 1/2
1 x 1/2
1 x 3/4
1-1/4 x 1/2
1-1/4 x 3/4
1-1/4 x 1
1-1/2 x 1/2
1-1/2 x 3/4
1-1/2 x 1
1-1/2 x 1-1/4
2 x 1/2
2 x 3/4
2x1
2 x 1-1/4
2 x 1-1/2
2-1/2 x 1/2
2-1/2 x 3/4
2-1/2 x 1
2-1/2 x 1-1/4
2-1/2 x 1-1/2
2-1/2 x 2
3 x 3/4
3 x 3/4
3x1
3 x 1-1/4
3 x 1-1/2
3x2
3 x 2-1/2
4x2
4 x 2-1/2
4x3
5x3
5x4
6x2
6x3
6x4
6x5
8x4
8x6
100
100
100
100
25
25
25
25
25
25
25
10
10
10
10
25
10
10
10
10
10
10
10
10
10
10
10
10
10
5
5
5
5
4
5
5
5
5
5
5
0.99
0.57
0.99
0.99
1.31
1.31
1.31
1.40
1.40
1.40
1.40
2.30
2.34
2.30
2.30
2.34
3.69
3.74
3.69
3.69
3.69
3.74
5.50
4.43
5.46
5.46
5.46
5.50
5.50
12.15
12.15
12.15
17.12
17.12
30.09
30.09
30.09
30.09
105.05
105.05
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-439-005
1/2 x 1/2
50
0.94
†Fabricated with M olded Pieces
Bushing, Threaded, 1-5/8 Long, MIPT X FIPT
279
PVC Pipe & Fittings
Bushing, Threaded, MIPT X FIPT
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-439-052
S1-PVC-439-072
S1-PVC-439-073
S1-PVC-439-098
S1-PVC-439-099
S1-PVC-439-101
S1-PVC-439-130
S1-PVC-439-131
S1-PVC-439-166
S1-PVC-439-167
S1-PVC-439-168
S1-PVC-439-209
S1-PVC-439-210
S1-PVC-439-211
S1-PVC-439-212
S1-PVC-439-249
S1-PVC-439-250
S1-PVC-439-251
S1-PVC-439-292
S1-PVC-439-338
3/8 x 1/4
1/2 x 1/4
1/2 x 3/8
3/4 x 1/4
3/4 x 3/8
3/4 x 1/2
1 x 1/2
1 x 3/4
1-1/4 x 1/2
1-1/4 x 3/4
1-1/4 x 1
1-1/2 x 1/2
1-1/2 x 3/4
1-1/2 x 1
1-1/2 x 1-1/4
2x1
2 x 1-1/4
2 x 1-1/2
2-1/2 x 2
3x2
50
50
50
50
50
50
50
50
25
25
25
25
25
25
25
10
10
10
10
5
2.42
2.42
2.42
1.52
1.52
1.52
2.09
2.09
3.16
3.16
3.16
3.78
3.78
3.78
3.78
4.06
4.06
4.06
14.20
16.79
Cap, FIPT
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-448-005
S1-PVC-448-007
S1-PVC-448-010
S1-PVC-448-012
S1-PVC-448-015
S1-PVC-448-020
S1-PVC-448-025
S1-PVC-448-030
S1-PVC-448-040
1/2
3/4
1
1-1/4
1-1/2
2
2-1/2
3
4
100
100
50
25
25
10
10
10
5
0.99
1.15
1.72
2.01
2.09
3.74
5.50
7.18
12.64
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-447-005
S1-PVC-447-007
S1-PVC-447-010
S1-PVC-447-012
S1-PVC-447-015
S1-PVC-447-020
S1-PVC-447-025
S1-PVC-447-030
S1-PVC-447-040
S1-PVC-447-050
S1-PVC-447-060
S1-PVC-447-080
1/2
3/4
1
1-1/4
1-1/2
2
2-1/2
3
4
5
6
8
100
100
50
25
25
25
10
10
5
5
5
4
0.49
0.57
0.86
1.23
1.31
1.60
5.05
5.54
12.52
21.02
30.01
75.37
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-482-015
S1-PVC-482-020
S1-PVC-482-025
1-1/2 (†2.169)
2 (†2.389)
2-1/2 (†3.385)
25
25
10
3.16
5.21
6.69
S1-PVC-482-030
S1-PVC-482-040
3 (†3.625)
4 (†3.625)
10
5
10.10
20.24
Cap, SOCKET
Coupling, Deep Socket, SOCKET
†Socket depth, each side.
280
PVC Pipe & Fittings
Coupling, FIPT X FIPT, Gray
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-430-005-45
S1-PVC-430-007-45
S1-PVC-430-101-45
S1-PVC-430-131-45
1/2
3/4
3/4 x 1/2
1 x 3/4
100
50
50
50
0.70
1.35
2.46
2.71
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-430-005
S1-PVC-430-007
S1-PVC-430-010
S1-PVC-430-101
S1-PVC-430-131
1/2
3/4
1
3/4 x 1/2
1 x 3/4
100
50
50
50
50
0.62
1.23
1.60
2.46
2.71
Coupling, FIPT X FIPT, White
Coupling, Nested, SOCKET
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-477-005†
S1-PVC-477-007
S1-PVC-477-010
1/2
3/4
1
100
50
50
0.41
0.49
0.78
†1/2" nested couplings do not meet AST M Standards for Sch. 40 fittings and
are not NSF listed.
Coupling, Reducer, SOCKET
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-429-101
S1-PVC-429-131
S1-PVC-429-168
S1-PVC-429-212
S1-PVC-429-251
S1-PVC-429-338
S1-PVC-429-422
S1-PVC-429-532
3/4 x 1/2
1 x 3/4
1-1/4 x 1
1-1/2 x 1-1/4
2 x 1-1/2
3x2
4x3
6x4
50
50
25
25
10
5
4
4
0.86
1.44
2.46
2.59
4.11
22.09
27.59
36.37
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-429-005
S1-PVC-429-007
S1-PVC-429-010
S1-PVC-429-012
S1-PVC-429-015
S1-PVC-429-020
S1-PVC-429-025
S1-PVC-429-030
S1-PVC-429-040
S1-PVC-429-050
S1-PVC-429-060
S1-PVC-429-080
S1-PVC-429-585
1/2
3/4
1
1-1/4
1-1/2
2
2-1/2
3
4
5
6
8
8X6
100
50
50
25
25
25
10
10
5
4
5
4
4
0.37
0.49
0.82
1.15
1.23
1.89
4.11
6.36
9.20
16.87
29.11
54.31
93.14
Coupling, SOCKET
281
PVC Pipe & Fittings
Coupling, SOCKET, Long, SLIP
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-428-015
S1-PVC-428-020
1-1/2 (†1.825)
2 (†1.945)
25
25
2.55
3.20
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-420-335
S1-PVC-420-337
S1-PVC-420-338
S1-PVC-420-419
S1-PVC-420-420
3x3x1x1
3 x 3 x 1-1/2 x 1-1/2
3x3x2x2
4 x 4 x 1-1/2 x 1-1/2
4x4x2x2
10
10
10
5
5
20.40
20.40
20.40
34.07
34.07
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-420-005
S1-PVC-420-007
S1-PVC-420-010
S1-PVC-420-012
S1-PVC-420-015
S1-PVC-420-020
S1-PVC-420-025
S1-PVC-420-030
S1-PVC-420-040
1/2
3/4
1
1-1/4
1-1/2
2
2-1/2
3
4
50
50
50
25
25
10
8
10
5
1.97
3.28
4.06
5.38
6.08
8.95
19.05
23.32
34.56
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-D321-020
S1-PVC-D321-030
2
3
50
20
3.41
10.02
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-D323-020
S1-PVC-D323-030
2
3
20
20
5.71
15.44
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-D309-020
S1-PVC-D309-030
2
3
25
20
14.17
42.12
†Socket depth, each side.
Cross, Reducing, SOCKET
Cross, SOCKET
DWV 1/8 BEND H x H
DWV 1/8 BEND, STREET H x SP
DWV LONG SWEEP 1/4 BEND, STREET H x SP
282
PVC Pipe & Fittings
Elbow, 45°, SOCKET
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-417-005
S1-PVC-417-007
S1-PVC-417-010
S1-PVC-417-012
S1-PVC-417-015
S1-PVC-417-020
S1-PVC-417-025
S1-PVC-417-030
S1-PVC-417-040
S1-PVC-417-050
S1-PVC-417-060
S1-PVC-417-080
1/2
3/4
1
1-1/4
1-1/2
2
2-1/2
3
4
5
6
8
50
50
50
25
25
25
10
10
5
5
4
4
0.86
1.31
1.60
2.22
2.79
3.65
9.40
14.57
26.11
51.81
64.49
155.13
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-408-005
S1-PVC-408-007
S1-PVC-408-010
S1-PVC-408-012
S1-PVC-408-015
S1-PVC-408-020
1/2
3/4
1
1-1/4
1-1/2
2
50
50
50
25
25
10
1.23
1.85
3.94
4.19
5.30
8.05
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-407-005
S1-PVC-407-007
S1-PVC-407-010
S1-PVC-407-012
S1-PVC-407-015
S1-PVC-407-020
S1-PVC-407-025
S1-PVC-407-030
S1-PVC-407-040
1/2
3/4
1
1-1/4
1-1/2
2
2-1/2
3
4
50
50
50
25
25
10
10
10
5
0.62
0.74
1.40
2.30
2.55
6.61
16.26
24.38
36.95
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-406-005
S1-PVC-406-007
S1-PVC-406-010
S1-PVC-406-012
S1-PVC-406-015
S1-PVC-406-020
S1-PVC-406-025
S1-PVC-406-030
S1-PVC-406-040
S1-PVC-406-050
S1-PVC-406-060
S1-PVC-406-080
1/2
3/4
1
1-1/4
1-1/2
2
2-1/2
3
4
5
6
8
50
50
50
25
25
25
10
10
5
5
4
3
0.53
0.62
1.07
1.89
2.01
3.08
9.40
11.25
20.03
51.81
63.71
164.12
Elbow, 90°, FIPT
Elbow, 90°, FIPT X SOCKET
Elbow, 90°, SOCKET
Elbow, 90-deg, Long Sweep, HUB X HUB
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
S1-PVC-D304-020
2
25
5.14
S1-PVC-D304-030
3
10
13.61
283
MLP $
PVC Pipe & Fittings
Elbow, Reducing, 90°, SOCKET X FIPT
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-407-074
S1-PVC-407-101
S1-PVC-407-130
S1-PVC-407-131
S1-PVC-407-168
S1-PVC-407-211
S1-PVC-407-212
S1-PVC-407-249
S1-PVC-407-250
S1-PVC-407-251
1/2 x 3/4
3/4 x 1/2
1 x 1/2
1 x 3/4
1-1/4 x 1
1-1/2 x 1
1-1/2 x 1-1/4
2x1
2 x 1-1/4
2 x 1-1/2
50
50
50
50
25
25
25
10
10
10
1.40
0.74
2.09
2.09
3.08
5.13
5.30
8.83
8.83
8.83
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-406-101
S1-PVC-406-130
S1-PVC-406-131
S1-PVC-406-168
S1-PVC-406-211
S1-PVC-406-212
S1-PVC-406-249
S1-PVC-406-250
S1-PVC-406-251
3/4 x 1/2
1 x 1/2
1 x 3/4
1-1/4 x 1
1-1/2 x 1
1-1/2 x 1-1/4
2x1
2 x 1-1/4
2 x 1-1/2
50
50
50
25
25
25
25
25
25
1.07
1.52
1.89
2.96
4.64
4.64
5.71
5.71
7.92
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-413-010
1
25
4.89
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-414-005
S1-PVC-414-010
S1-PVC-414-101
S1-PVC-414-130
1/2 x 1/2 x 1/2
1x1x1
3/4 x 3/4 x 1/2
1 x 1 x 1/2
50
25
50
25
2.75
4.89
3.53
4.60
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-412-005
S1-PVC-412-007
S1-PVC-412-010
S1-PVC-412-012
S1-PVC-412-015
1/2
3/4
1
1-1/4
1-1/2
50
50
50
25
25
1.52
1.89
3.16
3.9
4.23
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-410-005
S1-PVC-410-007
S1-PVC-410-010
S1-PVC-410-012
S1-PVC-410-015
S1-PVC-410-020
S1-PVC-410-101
1/2
3/4
1
1-1/4
1-1/2
2
3/4 x 1/2
50
50
50
25
25
10
50
1.15
1.31
2.22
3.08
3.24
7.92
1.60
Elbow, Reducing, 90°, SOCKET X SOCKET
Elbow, Side Outlet, 90°, SOCKET
Elbow, Side Outlet, 90°, SOCKET X SOCKET X FIPT
Elbow, Street, 90°, MIPT X FIPT
Elbow, Street, 90°, MIPT X SOCKET
284
PVC Pipe & Fittings
Elbow, Street, 90°, MIPT X SOCKET
Elbow, Street, 90°, Poly, MIPT X FIPT
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-M412-005†
S1-PVC-M412-007†
S1-PVC-M412-010
1/2
3/4
1
50
50
50
0.79
0.96
3.12
†Not Listed by NSF
Elbow, Street, 90°, SPIGOT X FIPT
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-411-005
S1-PVC-411-007
S1-PVC-411-010
S1-PVC-411-012
S1-PVC-411-015
1/2
3/4
1
1-1/4
1-1/2
50
50
50
25
25
1.40
1.68
2.96
3.53
3.98
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-409-005
S1-PVC-409-007
S1-PVC-409-010
S1-PVC-409-012
S1-PVC-409-015
S1-PVC-409-020
1/2
3/4
1
1-1/4
1-1/2
2
50
50
50
25
25
10
1.44
1.81
3.08
3.69
4.06
7.84
Elbow, Street, 90°, SPIGOT X SOCKET
O-Ring, Buna N 70 Shore
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-40213
S1-PVC-40216
S1-PVC-40220
S1-PVC-40225
S1-PVC-40231
1/2
3/4
1
1-1/4
2
1
1
1
1
1
1.60
1.72
2.18
3.69
4.97
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-450-005
S1-PVC-450-007
S1-PVC-450-010
S1-PVC-450-012
S1-PVC-450-015
S1-PVC-450-020
S1-PVC-450-025
S1-PVC-450-030
S1-PVC-450-040
1/2
3/4
1
1-1/4
1-1/2
2
2-1/2
3
4
50
50
50
25
25
10
10
10
5
1.40
1.52
2.46
2.55
2.75
3.53
4.93
7.43
16.83
Plug, MIPT
285
PVC Pipe & Fittings
Plug, SPIGOT
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-449-005
S1-PVC-449-007
S1-PVC-449-010
S1-PVC-449-012
S1-PVC-449-015
S1-PVC-449-020
S1-PVC-449-025
S1-PVC-449-030
S1-PVC-449-040
1/2
3/4
1
1-1/4
1-1/2
2
2-1/2
3
4
50
50
50
25
25
10
10
10
5
1.15
1.31
1.60
2.09
2.71
3.33
5.67
7.51
17.04
Riser Extender, MIPT X FIPT
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-434-005
S1-PVC-434-007
S1-PVC-434-008
S1-PVC-434-020
2-1/16 x 1/2 LONG
1-5/8 x 3/4 LONG
2-5/16 x 3/4 LONG
2-5/8 x 2 LONG
50
50
50
25
0.94
1.60
1.64
3.98
Snap-On Tee, SNAP-ON X FIPT
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-464-007
S1-PVC-464-101
S1-PVC-464-130
S1-PVC-464-131
3/4
3/4 x 1/2
1 x 1/2
1 x 3/4
25
25
50
25
2.34
2.01
3.53
3.53
Tee, Bullhead, SOCKET X SOCKET X SOCKET
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-401-074
S1-PVC-401-102
S1-PVC-401-132
S1-PVC-401-133
S1-PVC-401-213
S1-PVC-401-341
1/2 x 1/2 x 3/4
3/4 x 3/4 x 1
1 x 1 x 1-1/4
1 x 1 x 1-1/2
1-1/2 x 1-1/2 x 2
3x3x4
50
50
50
25
25
10
1.35
2.46
3.24
4.19
5.87
30.71
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-405-005
S1-PVC-405-007
S1-PVC-405-010
S1-PVC-405-012
S1-PVC-405-015
1/2
3/4
1
1-1/4
1-1/2
50
50
50
25
25
2.34
3.74
5.09
7.10
7.27
Tee, FIPT
286
PVC Pipe & Fittings
Tee, Reducing, SOCKET X SOCKET X FIPT
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-402-071
S1-PVC-402-072
S1-PVC-402-074
S1-PVC-402-094
S1-PVC-402-095
S1-PVC-402-101
S1-PVC-402-124
S1-PVC-402-125
S1-PVC-402-130
S1-PVC-402-131
S1-PVC-402-156
S1-PVC-402-157
S1-PVC-402-166
S1-PVC-402-167
S1-PVC-402-168
S1-PVC-402-199
S1-PVC-402-202
S1-PVC-402-209
S1-PVC-402-210
S1-PVC-402-211
S1-PVC-402-212
S1-PVC-402-239
S1-PVC-402-247
S1-PVC-402-248
S1-PVC-402-249
S1-PVC-402-250
S1-PVC-402-251
S1-PVC-402-287
S1-PVC-402-288
S1-PVC-402-289
S1-PVC-402-290
S1-PVC-402-291
S1-PVC-402-292
S1-PVC-402-333
S1-PVC-402-334
S1-PVC-402-335
S1-PVC-402-336
S1-PVC-402-337
S1-PVC-402-338
S1-PVC-402-416
S1-PVC-402-417
S1-PVC-402-418
S1-PVC-402-419
S1-PVC-402-420
S1-PVC-402-422
S1-PVC-402-490
S1-PVC-402-528
S1-PVC-402-530
S1-PVC-402-532
1/2 x 1/2 x 1/8
1/2 x 1/2 x 1/4
1/2 x 1/2 x 3/4
3/4 x 1/2 x 1/2
3/4 x 1/2 x 3/4
3/4 x 3/4 x 1/2
1 x 3/4 x 1/2
1 x 3/4 x 3/4
1 x 1 x 1/2
1 x 1 x 3/4
1-1/4 x 1 x 1/2
1-1/4 x 1 x 3/4
1-1/4 x 1-1/4 x 1/2
1-1/4 x 1-1/4 x 3/4
1-1/4 x 1-1/4 x 1
1-1/2 x 1-1/4 x 1/2
1-1/2 x 1-1/4 x 1
1-1/2 x 1-1/2 x 1/2
1-1/2 x 1-1/2 x 3/4
1 1/2 x 1-1/2 x 1
1-1/2 x 1-1/2 x 1-1/4
2 x 1-1/2 x 1
2 x 2 x 1/2
2 x 2 x 3/4
2x2x1
2 x 2 x 1-1/4
2 x 2 x 1-1/2
2-1/2 x 2-1/2 x 1/2
2-1/2 x 2-1/2 x 3/4
2-1/2 x 2-1/2 x 1
2-1/2 x 2-1 2 x 1-1/4
2-1/2 x 2-1/2 x 1-1/2
2-1/2 x 2-1/2 x 2
3 x 3 x 1/2
3 x 3 x 3/4
3x3x1
3 x 3 x 1-1/4
3 x 3 x 1-1/2
3x3x2
4 x 4 x 3/4
4x4x1
4 x 4 x 1-1/4
4 x 4 x 1-1/2
4x4x2
4x4x3
5x5x4
6x6x2
6x6x3
6x6x4
50
50
50
50
50
50
50
50
50
50
50
25
25
25
25
25
25
25
25
25
25
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
4
5
5
5
5
5
5
5
5
5
1.85
1.85
1.85
1.27
1.27
1.15
2.42
2.42
1.72
2.46
3.86
3.86
4.06
4.06
4.06
5.05
5.05
5.05
5.05
5.05
5.05
6.36
6.36
6.36
6.36
6.36
6.36
13.71
13.71
13.71
13.71
13.71
13.71
19.66
19.66
19.62
19.62
19.62
19.62
32.76
32.76
32.76
32.76
32.76
32.76
85.55
111.00
111.00
111.00
287
PVC Pipe & Fittings
Tee, Reducing, SOCKET X SOCKET X SOCKET
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-401-094
S1-PVC-401-095
S1-PVC-401-101
S1-PVC-401-122
S1-PVC-401-124
S1-PVC-401-125
S1-PVC-401-126
S1-PVC-401-130
S1-PVC-401-131
S1-PVC-401-156
S1-PVC-401-157
S1-PVC-401-158
S1-PVC-401-166
S1-PVC-401-167
S1-PVC-401-168
S1-PVC-401-199
S1-PVC-401-201
S1-PVC-401-202
S1-PVC-401-203
S1-PVC-401-209
S1-PVC-401-210
S1-PVC-401-211
S1-PVC-401-212
S1-PVC-401-238
S1-PVC-401-239
S1-PVC-401-241
S1-PVC-401-247
S1-PVC-401-248
S1-PVC-401-249
S1-PVC-401-250
S1-PVC-401-251
S1-PVC-401-287
S1-PVC-401-288
S1-PVC-401-289
S1-PVC-401-290
S1-PVC-401-291
S1-PVC-401-292
S1-PVC-401-333
S1-PVC-401-334
S1-PVC-401-335
S1-PVC-401-336
S1-PVC-401-337
S1-PVC-401-338
S1-PVC-401-416
S1-PVC-401-417
S1-PVC-401-418
S1-PVC-401-419
S1-PVC-401-420
S1-PVC-401-422
S1-PVC-401-486
3/4 x 1/2 x 1/2
3/4 x 1/2 x 3/4
3/4 x 3/4 x 1/2
1 x 1/2 x 1
1 x 3/4 x 1/2
1 x 3/4 x 3/4
1 x 3/4 x 1
1 x 1 x 1/2
1 x 1 x 3/4
1-1/4 x 1 x 1/2
1-1/4 x 1 x 3/4
1-1/4 x 1 x 1
1-1/4 x 1-1/4 x 1/2
1-1/4 x 1-1/4 x 3/4
1-1/4 x 1-1/4 x 1
1-1/2 x 1-1/4 x 1/2
1-1/2 x 1-1/4 x 3/4
1-1/2 x 1-1/4 x 1
1-1/2 x 1-1/4 x 1-1/4
1-1/2 x 1-1/2 x 1/2
1-1/2 x 1-1/2 x 3/4
1-1/2 x 1-1/2 x 1
1-1/2 x 1-1/2 x 1-1/4
2 x 1-1/2 x 3/4
2 x 1-1/2 x 1
2 x 1-1/2 x 1-1/2
2 x 2 x 1/2
2 x 2 x 3/4
2x2x1
2 x 2 x 1-1/4
2 x 2 x 1-1/2
2-1/2 x 2-1/2 x 1/2
2-1/2 x 2-1/2 x 3/4
2-1/2 x 2-1/2 x 1
2-1/2 x 2-1/2 x 1-1/4
2-1/2 x 2-1/2 x 1-1/2
2-1/2 x 2-1/2 x 2
3 x 3 x 1/2
3 x 3 x 3/4
3x3x1
3 x 3 x 1-1/4
3 x 3 x 1-1/2
3x3x2
4 x 4 x 3/4
4x4x1
4 x 4 x 1-1/4
4 x 4 x 1-1/2
4x4x2
4x4x3
5x5x2
50
50
50
50
50
50
50
50
50
25
25
25
25
25
25
25
25
25
25
25
25
25
25
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
4
4
5
5
5
5
5
1.23
1.23
0.82
2.42
2.42
2.42
2.42
1.44
1.60
3.33
3.33
3.33
2.34
2.34
2.38
4.11
4.11
4.11
4.11
4.11
4.11
4.15
4.11
5.87
5.87
5.87
4.06
4.06
4.06
4.06
4.06
12.48
12.48
12.48
12.48
12.48
12.48
17.90
17.90
17.90
17.90
17.90
17.86
29.76
29.76
29.76
29.76
29.76
29.76
69.75
S1-PVC-401-488
S1-PVC-401-490
S1-PVC-401-528
S1-PVC-401-530
S1-PVC-401-532
S1-PVC-401-582
S1-PVC-401-585
5x5x3
5x5x4
6x6x2
6x6x3
6x6x4
8x8x4
8x8x6
5
5
5
5
5
2
2
69.75
69.75
100.12
100.12
100.12
232.22
232.22
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-D400-020
2
4
10.10
Tee, Sanitary
288
PVC Pipe & Fittings
Tee, SOCKET
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-401-003
S1-PVC-401-005
S1-PVC-401-007
S1-PVC-401-010
S1-PVC-401-012
S1-PVC-401-015
S1-PVC-401-020
S1-PVC-401-025
S1-PVC-401-030
S1-PVC-401-040
S1-PVC-401-050
S1-PVC-401-060
S1-PVC-401-080
3/8
1/2
3/4
1
1-1/4
1-1/2
2
2-1/2
3
4
5
6
8
100
50
50
50
25
25
25
10
10
5
4
4
2
1.97
0.66
0.74
1.40
2.18
2.59
3.82
12.52
16.46
29.76
71.84
100.12
232.22
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-403-005
S1-PVC-403-007
1/2
3/4
50
50
0.86
1.31
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-402-005
S1-PVC-402-007
S1-PVC-402-010
S1-PVC-402-012
S1-PVC-402-015
S1-PVC-402-020
S1-PVC-402-030
S1-PVC-402-040
1/2
3/4
1
1-1/4
1-1/2
2
3
4
50
50
50
25
25
10
10
5
0.82
1.31
2.46
3.86
5.05
6.4
24.75
37.85
Tee, SOCKET X FIPT X SOCKET
Tee, SOCKET X SOCKET X FIPT
Trap, Running, SLIP X SLIP
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-5-408
S1-5-409
3/4
3/4
100
100
1.79
1.79
Union, O-Ring Type, FIPT X FIPT
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-458-005
S1-PVC-458-007
S1-PVC-458-010
S1-PVC-458-012
S1-PVC-458-015
S1-PVC-458-020
1/2
3/4
1
1-1/4
1-1/2
2
10
10
10
5
5
5
5.67
9.44
12.85
22.13
22.58
27.75
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-457-005
S1-PVC-457-007
S1-PVC-457-010
S1-PVC-457-012
S1-PVC-457-015
S1-PVC-457-020
1/2
3/4
1
1-1/4
1-1/2
2
10
10
10
5
5
5
5.05
5.75
5.87
19.01
19.79
26.68
Union, O-Ring Type, SOCKET X SOCKET
289
PVC Pipe & Fittings
Wye, Hub
SOURCE 1 PART NO.
DIM. (INCHES)
CTN QTY
MLP $
S1-PVC-D600-020
2
4
12.32
SCHEDULE 40 PVC PIPE
PVC Condensate Pipe
Straight End
SOURCE 1 PART NO.
DIA. (IN)
LENGTH (FT)
UOM/ORDER QTY
MLP $
S1-5-401
S1-5-404
S1-5-405
S1-5-407
3/4"
2"
3"
3/4"
10'
10'
10'
20'
500 PIECES
100 FEET
50 FEET
500 FEET
1.46
3.79
7.46
1.46
290
J.W. HARRIS BRAZING SOLDER
Brazing Rods & Solder
SOURCE 1 PART NO.
DESCRIPTION
VENDOR MFG. N0.
ALLOY
MELT
FLOW
MLP $
S1-00107138001
61035
BCuP-5; 15/80/5 (Ag/Cu/P)
1190
1475
See Note1 Below
51035
6/88/6 (Ag/Cu/P)
1190
1460
See Note1 Below
41035
BCuP-3; 5/89/6 (Ag/Cu/P)
1190
1495
See Note1 Below
31035
BCuP-6; 2/91/7 (Ag/Cu/P)
1190
1450
See Note1 Below
21035
BCuP-2; 0/92.75/7.2 (Ag/Cu/P)
1310
1460
See Note1 Below
S1-00107139001
15% SILVER BRAZING ALLOY; .125" x .050" x 20" RODS,
1-LB. TUBE
1-LB. TUBE
1-LB. TUBE
1-LB. TUBE
1-LB. TUBE
HIGH SILVER BRAZING ALLOY, 1-OZ. COIL
75310
1145
1205
See Note1 Below
S1-00107139002
80310
1220
1305
See Note1 Below
S1-00107139003
76310
1225
1370
See Note1 Below
S1-00107139004
S1-00107141001
S1-00107141002
S1-00107141003
S1-00107142001
SILVER BEARING, LEAD-FREE SOFT SOLDER
GENERAL PURPOSE LOW TEMP LEAD BEARING
SOLDER
SOLDER
SOLDER
LEAD-FREE SOLDER, 1/8" DIA x 1-LB ROLL
77310
10009
10001
10030
10028
BAg-7; 56/22/17/5
(Ag/Cu/Zn/Sn)
BAg-24; 50/20/28/0
(Ag/Cu/Zn/Sn) plus 2% Ni
BAg-5; 45/30/25/0
(Ag/Cu/Zn/Sn)
40/30/30/0 (Ag/Cu/Zn/Sn)
6/0/94 (Ag/Cu/Sn)
3.6/0/96.4 (Ag/Cu/Sn)
0/0/95 (Ag/Cu/Sn) plus 5 Sb
50/50 (Sn/Pb)
1245
431
431
450
361
1340
535
431
460
414
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
See Note1 Below
10035
40/60 (Sn/Pb)
361
460
See Note1 Below
10036
60/40 (Sn/Pb)
361
370
See Note1 Below
S1-00107138002
S1-00107138003
S1-00107138004
S1-00107138005
S1-00107142002
S1-00107142003
S1-16000
BRGT61
61.29
NOT E1 - REFE R T O WEEK LY COM M ODITY S HEET .
Flux & Miscellaneous
SOURCE 1 PART NO.
DESCRIPTION
VENDOR MFG. N0.
MLP $
S1-00107140001
S1-00107140002
40022
40050
See Note1 Below
See Note1 Below
40002
See Note1 Below
S1-00107143001
S1-00107144001
S1-40006
ALL-PURPOSE BRAZING FLUX AWS TYPE # 3A; O-F-499D (TYPE B); AMS-3410G
BLACK-BORON MODIFIED HIGH TEMP BRAZING FLUX AWS TYPE # 3A;
O-F-499D (TYPE B); AMS-3410G
ALL-PURPOSE LIQUID BRAZING FLUX AWS TYPE # 3A; O-F-499D (TYPE B);
AMS-3410G
GENERAL PURPOSE FLUX PASTE
LOW-TEMPERATURE ALUMINUM SOLDER KIT
SOLDERING FLUX,STAY-CLEAN ALUM,4-OZ
40027
10022
40006
S1-40051
BRAZING FLUX,STAY SILV BLK,1-LB
40051
S1-40057
BRIDGIT PASTE FLUX, 4-OZ JAR.
40057
See Note1 Below
See Note1 Below
Refer to weekly
commodity sheet
Refer to weekly
commodity sheet
8.88
S1-00107140003
NOT E1 - REFER T O WEEKLY COM M ODITY SHEET .
Blaze Barrier Cloth
• 18" X 18" Plain
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-16500
HEAT RESISTANT CLOTH
78.64
Hand Torch Fuel Cylinders
SOURCE 1 PART NO.
DESCRIPTION
SHIPPING MULTIPLE
MLP $
S1-525-MT1
MAP-PRO GAS, 16-OZ
12
27.82
S1-525-PT1
PROPANE GAS, 14.1-OZ
12
19.64
291
LUCAS-MILHAUPT BRAZING RINGS
Brazing Rings
SOURCE 1 PART NO.
DESCRIPTION
MLP $
RINGS,BRAZING,1/4" OD
OUTER DIAMETER
(INCHES)
1/4
STD. PACK
S1-98700
25
S1-98701
3/8
25
S1-98702
1/2
25
S1-98703
5/8
25
S1-98704
3/4
25
S1-98705
7/8
25
S1-98706
RINGS,BRAZING,1-1/8" OD,
1 - 1/8
10
Refer to weekly
commodity sheet
Refer to weekly
commodity sheet
Refer to weekly
commodity sheet
Refer to weekly
commodity sheet
Refer to weekly
commodity sheet
Refer to weekly
commodity sheet
Refer to weekly
commodity sheet
292
TURBOTORCH® WELDING EQUIPMENT
X-3B flexible kit brazes light to medium
gauge steel.
Components:
• AR-B (CGA 520) Regulator
• G-4 handle
• AH-12 hose
• A-3 and A-11 tips
• Soft solders to 3” (75 mm)
• Silver brazes to 1-5/8” (40 mm)
• “B” tank connection
• Instruction manual
X-5B flexible light-duty kit.
Components:
• AR-B (CGA 520) regulator
• G-4 handle
• AH-12 hose
• A-5 tip
• Soft solders to 1-1/2” (40 mm)
• Silver brazes to 3/4” (20 mm)
• “B” tank connection
• Instruction manual
SOURCE 1 PART NO.
DESCRIPTION
VENDOR MFG NUMBER
MLP $
S1-0386-0297
S1-0386-1345
S1-0386-1370
S1-1424-0018
S1-1424-0405
S1-1424-0407
S1-52639546000
S1-52639548000
S1-52639549000
S1-52639550000
S1-52639551000
S1-52639552000
S1-52639553000
S1-52639554000
S1-52639555000
S1-52639556000
S1-52639557000
S1-52639560000
S1-52639561000
S1-52639563000
S1-52639564000
S1-52639565000
S1-52639566000
S1-52639567000
S1-52639568000
S1-52639569000
S1-52639570000
S1-52639571000
S1-52639572000
S1-52639573000
S1-52639574000
S1-52639575000
S1-52639576000
S1-52639577000
S1-52639578000
S1-52639579000
S1-52639580000
S1-52639581000
LIGHTER,FLINT,TRIPLE
KIT,TOTE,OXY-ACETYL,W/O TANKS,TTV-J-ACP
KIT,PURGE,NITROGEN,NPK-TT
GAUGE 2" x 600 GOLD TINT
GAUGE 50MM 30PSIG/200 KP
GAUGE 50MM 400PSIG/2800
HOSE,BLOW GUN,BLUE 1/4" STD,#30272 BGH
TANK,MAPP,14.1 OZ,CGA600 HAZ MT-1
TANK,PROPANE,14.1 OZ,CGA600 HAZ PT-1
NOZZLE,WELDING,TIP SIZE 00, 00-W-1-CS
NOZZLE,WELDING,TIP SIZE 00, 00-W-J-CS
0-3-101 TURBOSKILL CUTTING TIP
0-W-J-CS WELDING NOZZLE-VICTOR CLAMSHELL
GAUGE,ACETYLENE,REPLCMNT 1.4" AIR/FUEL
HANDLE,FOR 110 SERIES 101-01FP
HANDLE,WELDING,J-28,FOR CWK 103-01FP
TIP END,ACETYLENE,3/8" 12A-TE
1-3-101CS CUTTING TIP (VICTOR CLAMSHELL)
TRUCK,CYLINDER,ACETYLENE/OXYGEN 143-01
CUTTING ATTACHMENT, CA-250 151-01FP
CUTTING ATTACHMENT,CA-1260 152-01FP
ADAPTER,CGA600/023 163-01T
NOZZLE,WELDING 191-02P
MULTI-FLAME EXPRESS UNWLD 198-01P
NOZZLE,WELDING,TIP SIZE 1, 1-W-J-CS
GAUGE,REPLACEMENT,2" x 4000 LB
GAUGE,REPLACEMENT,2" x 600 LB
REGULATOR,ACETYLENE,REAR MOUNT 201-05FP
REGULATOR,OXYGEN,REAR MOUNT 221-05FP
GAUGE,30 PSI 230-01P
TIP,CUTTING SIZE 2 2-3-101-CS
0386-0297
0386-1345
0386-1370
1424-0018
1424-0405
1424-0407
1412-0145
0916-0122
0916-0004
0387-0029
0387-0039
0387-0145
0387-0030
0387-0040
0426-8000
0386-0310
0386-0311
0386-1066
0387-0146
1421-0039
0386-0378
0386-0380
0386-0508
0386-0166
0386-0168
0386-0173
0386-0175
0386-0179
0387-0031
0387-0041
0426-8011
0426-8010
0386-0784
0386-0786
0386-1196
0387-0147
0386-1197
0386-1198
32.18
1325.61
513.18
44.07
24.50
31.21
93.68
17.86
12.11
78.57
67.86
23.07
80.04
42.86
39.29
221.43
255.25
50.61
23.07
250.00
228.57
307.14
68.32
64.29
35.71
64.29
82.14
178.57
80.04
100.43
51.36
43.21
207.14
310.29
47.25
25.00
47.25
47.25
S1-52639582000
S1-52639583000
S1-52639584000
S1-52639585000
S1-52639586000
S1-52639587000
S1-52639588000
S1-52639589000
S1-52639590000
S1-52639591000
245-02P REGULATOR (TURBO CLAMSHELL)
245-03P REGULATOR (TURBO CLAMSHELL)
HOSE,TWIN,OXY/ACETYLENE,A,12.5FT 252-03P
CLEANER,TIP 255-01P
NOZZLE,UN-J UNIVERSAL 257-01P
NOZZLE,WELDING,TIP SIZE 2,VC 2-W-1-CS
HOSE,DUAL FUEL 20' x 3/16"
0386-1199
0386-0813
0386-0814
0386-1094
0386-1213
0386-0182
0387-0032
0387-0042
1412-0108
0386-1059
60.71
220.61
277.18
93.43
19.07
118.61
122.64
39.29
135.71
50.00
S1-52639592000
S1-52639593000
S1-52639594000
S1-52639595000
S1-52639596000
S1-52639597000
S1-52639598000
S1-52639599000
S1-52639600000
TIP END,LP&MAPP,3/8" 3T-TE
NOZZLE,WELDING,TIP SIZE 3,VC 3-W-1-CS
TIP END,SELF-LIGHTING 44TL-TE
NOZZLE,WELDING,TIP SIZE 4 4-W-J
GAUGE,ACETYLENE,REPLCMNT 50MM 100 LB
GAUGE,LP ACETYLENE,REPLCMNT 50MM 30 LB
GAUGE,LP OXYGEN,REPLCMNT 50MM 400 LB
0386-1067
0387-0033
0387-0043
0386-1263
0386-1068
0387-0044
0426-8002
0426-8001
0426-8003
71.43
83.29
75.00
46.43
73.14
78.57
47.21
47.21
43.21
293
SOURCE 1 PART NO.
DESCRIPTION
VENDOR MFG NUMBER
MLP $
S1-52639601000
S1-52639602000
S1-52639603000
S1-52639604000
S1-52639605000
S1-52639606000
S1-52639607000
S1-52639608000
S1-52639609000
S1-52639610000
S1-52639611000
S1-52639612000
S1-52639613000
S1-52639614000
S1-52639615000
S1-52639616000
S1-52639617000
S1-52639618000
S1-52639619000
S1-52639620000
S1-52639621000
S1-52639622000
S1-52639623000
S1-52639624000
GAUGE,HP OXYGEN,REPLCMNT 50MM 4000 LB
NOZZLE,WELDING BOXED 5-W-J
NOZZLE,HEATING W/6.5" ELBOW 6 TYPE 55
A-11 ACETYLENE TIP
TIP,ACETYLENE,1/2" A-14
TIP,ACETYLENE TURBO 3/16" A-3
A-5 ACETYLENE TIP
A-8 ACETYLENE TIP
ADAPTOR,1/8 NPTM,3/8-24 RH(M),TURBOSNAKE
GAUGE,ACETYLENE AG-1
AH-12 HOSE ACETYLENE 12 FT.
HOSE,ACETYLENE,24' AH-24
AR-B ACETYLENE REGULATOR
REGULATOR,ACETYLENE AR-MC
0426-8004
0386-1064
0386-1069
0325-0088
0323-0357
0325-0089
0325-0090
0386-1065
0386-0104
0386-0105
0386-0100
0386-0101
0486-0001
0386-0106
0386-0102
0486-0002
0386-0103
0486-0003
0915-0046
0386-1200
0386-1090
0386-1091
0386-0725
0386-0726
51.32
74.00
79.96
100.00
350.00
114.29
132.14
47.36
221.75
273.21
103.57
174.43
125.00
264.29
184.79
146.43
179.93
161.79
50.00
89.32
100.57
122.07
219.68
169.36
S1-52639625000
S1-52639626000
S1-52639627000
S1-52639628000
S1-52639629000
S1-52639630000
S1-52639635000
S1-52639636000
S1-52639637000
S1-52639638000
S1-52639639000
S1-52639640000
S1-52639641000
S1-52639642000
S1-52639643000
S1-52639644000
S1-52639645000
S1-52639646000
S1-52639647000
S1-52639648000
S1-52639650000
S1-52639651000
S1-52639652000
S1-52639653000
S1-52639654000
S1-52639655000
S1-52639656000
ALLOY,BRAZING,BRONZEFLOW 1 LB BF-1
BG BLOW GUN ASSEMBLY
BTMCR ADAPTER ACETYLENE MC-B TANK
CUTTING ATTACHMENT 8" CA1260-CS
FITTING INLET MC ACETYLENE CGA-200
VALVE,CHECK FOR "A" HOSE
CYLINDER,ACETYLENE,B,40 CUFT,CGA520 AC-B
CYLINDER,ACETYLENE,10 CUFT,CGA200 AC-MC
CYLINDER,OXYGEN,R,20 CUFT,CGA540 OX-20
CYLINDER,NITROGEN,40 CUFT,CGA580 NT-40
D-1 DUAL TIP, PROVANTAGE
TIP,DUAL FLAME,1/2"-1-1/8"PROVANTAGE D-2
TIP,EXTENSION,10"FLEX PROVANTAGE E-10
TIP,EXTENSION,6"FLEX PROVANTAGE E-6
FLINT,LIGHTER,REPLACEMENT PKG=5 F-1 (M5)
G-4 HANDLE ACETYLENE W/VALVES
HOSE,PROPANE,12' H-12
HOSE,PROPANE,24' H-24
HANDLE,LP W/VALVE H-4
SWIVEL & NUT,INLET FOR CGA 520
L1- STRICKER
KIT,LP CONTRACTORS LP-1
KIT,LP SERVICE LP-2
KIT,LP STARTER LP-3
ADAPTER,ACETYLENE MC-B TANK MCT
TIP,ACETYLENE,MULTI-SWIRL 3/8" MSA-8
KIT,MULTI-SWIRL,MSKA-1
0386-0422
0660-0105
0386-0503
0387-0003
0386-1104
0650-0066
0916-0005
0916-0002
0916-0003
0916-0028
0386-0545
0386-0546
0386-0557
0386-0556
1423-0024
0386-0308
1412-0080
0386-1087
0386-0300
0386-1105
1423-0023
0386-0247
0386-0007
0386-0006
0386-0505
0386-0365
0386-0366
39.29
57.14
80.68
350.00
67.86
32.14
267.86
271.18
287.39
516.07
125.00
125.00
89.29
90.14
4.57
186.64
87.00
150.00
140.50
67.86
8.46
532.14
557.14
425.00
78.57
172.39
478.57
S1-52639657000
S1-52639658000
S1-52639660000
S1-52639661000
S1-52639662000
S1-52639663000
S1-52639664000
S1-52639665000
S1-52639666000
S1-52639667000
S1-52639668000
S1-52639669000
S1-52639670000
S1-52639671000
S1-52639672000
S1-52639673000
S1-52639674000
S1-52639675000
KIT,NITROGEN BLOWOFF/PURGE 20CUFT NPK-20
KIT,NITROGEN BLOWOFF/PURGE 40CUFT NPK-40
IGN,PIEZO W/1.8MM LEAD NTK SZ-595G-005E
ORIFICE,FOR TURBOTORCH TIP OR-A11
ORIFICE,FOR TURBOTORCH TIP OR-T3
ORIFICE,FOR TURBOTORCH TIP OR-T6
KIT,ORIFICE&FILTER REPLACEMENT ORTL-44
SYSTEM,PLASMA CUTTING PC 250
KIT,ACETYLENE,B,15 PSI PL-12ADLX-B
KIT,ACETYLENE STANDARD PL-12A STD 15 PSI
TIP,ACETYLENE,3/8" ASS'Y PL-12A PACKAGED
0386-1234
0386-1236
1414-0029
0386-1004
0386-1005
0386-1000
0386-1001
0386-1006
0386-1002
0386-1003
0386-1021
0386-1024
0386-1048
1445-0927
0386-0836
0386-0828
0386-0820
0386-0874
460.71
525.00
44.18
32.14
51.43
35.71
37.43
43.36
41.00
42.86
37.43
42.86
39.29
3985.71
557.14
303.57
281.32
139.29
S1-52639676000
S1-52639677000
S1-52639678000
S1-52639679000
S1-52639680000
S1-52639681000
S1-52639682000
KIT,DELUXE,LP&MAPP,PL-3TDLX
TIP,LP&MAPP,3/8" PL-3T
KIT,STANDARD,LP&MAPP,PL-4T
KIT,ACETYLENE,B,15 PSI PL-5ADLX-B
KIT,ACETYLENE,MC,15 PSI PL-5ADLX-MC
0386-0837
0386-0821
0386-0838
0386-0830
0386-0822
0386-0833
0386-0832
478.57
204.64
396.43
335.71
208.18
417.86
507.96
294
SOURCE 1 PART NO.
DESCRIPTION
VENDOR MFG NUMBER
MLP $
S1-52639683000
S1-52639684000
S1-52639685000
S1-52639686000
S1-52639687000
S1-52639688000
S1-52639689000
S1-52639690000
S1-52639691000
S1-52639692000
S1-52639693000
S1-52639694000
S1-52639695000
S1-52639696000
S1-52639697000
S1-52639698000
S1-52639699000
S1-52639700000
S1-52639701000
S1-52639702000
S1-52639703000
S1-52639704000
S1-52639705000
S1-52639706000
PL-812 PROLINE TORCH SHIELD
PL-8A DELUXE B KIT (15 PSI ACETYLENE)
KIT,ACETYLENE,MC,15 PSI PL-8ADLX-MC
KIT,ACETYLENE,15 PSI PLF-12A-DLX-B
KIT,ACETYLENE,15 PSI PLF-5A-DLX-MC
KIT,ACETYLENE,15 PSI PLF-8A-DLX-MC
HANDLE,ACETYLENE,PLF-A5 15 PSI
KIT,PRO SNAKE,SIZE 3,LP&MAPP PS-3T
KIT,PRO SNAKE,SIZE 4,LP&MAPP PS-4T
TUBE,REACTOR ANNEALED TT-LP
REGULATOR,LP&MAPP R-LP
TIP,SOF-FLAME,ACETYLENE 3/8-1/2" S-3
TIP,SOF-FLAME,ACETYLENE 1/2-1" S-4
TIP,SOF-FLAME,ACETYLENE 3/4- 1-1/2" S-5
TIP,SOF-FLAME,ACETYLENE 1"-4" S-6
ADAPTER,SNAPPY,ACETYLENE,SA
TIP,ACETYLENE,7/16 TIP QC SA-11
0386-0818
0386-0839
0386-0823
0386-0561
0386-0835
0386-0834
0386-0819
0386-0868
0386-0865
0386-0864
0386-0867
0386-0866
0386-0872
0386-0840
0386-0841
0337-0042
0386-0705
0386-0112
0386-0113
0386-0114
0386-0115
0386-0500
0426-6003
0426-6004
259.04
500.00
219.43
94.61
545.04
428.57
183.14
485.71
439.29
446.43
464.29
464.29
164.29
457.14
478.57
25.00
146.43
37.07
42.86
50.00
60.71
73.14
136.57
157.14
S1-52639707000
S1-52639708000
S1-52639709000
S1-52639711000
S1-52639712000
S1-52639713000
S1-52639714000
S1-52639715000
S1-52639716000
S1-52639717000
S1-52639718000
S1-52639719000
S1-52639720000
S1-52639721000
S1-52639729000
S1-52639730000
S1-52639731000
S1-52639732000
S1-52639733000
S1-52639734000
S1-52639735000
S1-52639736000
S1-52639737000
S1-52639738000
S1-52639739000
S1-52639741000
S1-52639742000
TIP,ACETYLENE,5/16 QC SA-8
TORCH,PENCIL,PROPANE SK-100
TORCH,HAND MAPP OR LP 360 SWIVEL SK-600
TORCH,HAND,SELF-LIGHTING DUAL SK-7000
KIT,ACETYLENE,TURBOSKILL SKB-3
TIP,CUTTING,3-3-101 STYLE SKC-3
SKCA CUTTING ATTACHMENT TURBOSKILL
SKCV TURBOSKILL ACCESSORY CHECK VALVE SET
HOSE,ACETYLENE 12' X 3/16" ASS'Y SKH-12A
HANDLE,ACETYLENE AIR/FUEL 3/16" SKH-1A
SKH-7A TURBOSKILL OXY-FUEL HANDLE
SKHT TURBOSKILL 12 1/2’ DUAL 3/16" OXY/ACETY HOSE
SKR-200R TURBOSKILL REAR ENTRY ACETYLENE REGULATOR
SKR-540R TURBOSKILL REAR ENTRY OXYGEN REGULATOR
REGULATOR,ACETYLENE AIR/FUEL SKR-B
REGULATOR,ACETYLENE AIR/FUEL SKR-MC
REGULATOR,PURGE,NITROGEN SKRP-125
REGULATOR,PURGE,NITROGEN SKRP-425
TIP,WELDING & BRAZING NOZZLE SKW-0
TIP,LP TURBOSKILL SLP-3
TIP,LP&MAPP 1/8-1/2"SOFT/MAPP ST-1
TIP,TURBOTORCH ST-11 PACKAGED
0426-6000
0426-6001
0426-6002
0426-4002
0426-4000
0426-4001
0426-0001
0426-6015
0426-5500
0426-8008
0426-8005
0426-5000
0426-5002
0426-8007
0426-2006
0426-2005
0426-2003
0426-2002
0426-2000
0426-2001
0426-6008
0426-6009
0426-6010
0426-6011
0426-6005
0386-0170
0386-1282
97.82
119.18
132.14
40.04
107.14
132.14
400.00
42.86
214.29
54.86
64.29
132.14
171.43
57.14
252.86
275.00
155.21
160.71
183.14
196.43
40.43
42.86
42.86
46.43
107.14
85.71
125.00
S1-52639743000
S1-52639744000
S1-52639745000
S1-52639746000
S1-52639747000
S1-52639748000
S1-52639749000
S1-52639750000
S1-52639751000
S1-52639752000
S1-52639753000
S1-52639754000
S1-52639755000
S1-52639756000
S1-52639757000
S1-52639758000
S1-52639759000
S1-52639760000
TIP,EXTREME,LP&MAPP ST-3
TIP,ASSEMBLY SELF-IGNITING ST-33
TIP,SNAKE,LP&MAPP ST-4
TIP,TURBO SNAKE,SMALL,LP&MAPP ST-5
TORCH,DUAL FUEL,LP&MAPP ST-1 TIP STK-1
KIT,TURBOTORCH STK-11
KIT,DUAL FUEL,TORCH W/CASE STK-8B
STK-9 DUAL FUEL TORCH
TORCH,DUAL FUEL,LP&MAPP ST-33 TIP STK-99
REGULATOR,LP&MAPP STK-R
ORIFICE,REPLACEMENT LP&MAPP STOR-1
ORIFICE,REPLACEMENT LP&MAPP STOR-3
TIP,LP NO. 2, 5/16" T-2
TIP,LP NO. 3, 7/16" T-3
TIP,LP NO. 4, 1/2" T-4
TIP ASSEMBLY PACKAGED T-44TL
TIP,LP NO. 5, 3/4" T-5
TIP ASSEMBLY PACKAGED T-503
0386-0171
0386-0850
0386-0183
0386-0184
0386-0408
0386-1283
0386-0404
0386-0403
0386-0851
0386-0687
0386-1030
0386-1031
0386-0150
0386-0151
0386-0152
0386-1266
0386-0153
0386-1298
104.86
126.57
132.14
96.43
125.00
167.86
314.29
196.43
132.14
103.57
42.86
37.21
126.46
130.11
157.14
89.29
164.29
62.25
S1-52639761000
S1-52639762000
S1-52639763000
S1-52639764000
S1-52639765000
S1-52639766000
S1-52639767000
TIP ASSEMBLY PACKAGED T-504
TIP,LP NO. 6, 1" T-6
RACK,TANK,45 DEG,FOR 1 LB TANK TSR
TANK,PROPANE,10LB,CGA510 POL T-10PS-MT
TIP,CUTTING,PLASMA (5) FOR TPC-25 TCT-25
ELECTRODE,AIR PLASMA PKG=5 TE-25
DISTRIBUTOR,GAS PLASMA TGD-25
0386-1296
0386-0154
0386-0528
0916-0029
1445-0902
1445-0904
1445-0905
89.29
200.00
82.89
225.00
93.71
104.39
67.86
295
®
TURBOTORCH WELDING EQUIPMENT
SOURCE 1 PART NO.
DESCRIPTION
VENDOR MFG NUMBER
MLP $
S1-52639768000
S1-52639769000
S1-52639770000
S1-52639771000
S1-52639772000
S1-52639773000
S1-52639774000
S1-52639775000
S1-52639776000
S1-52639777000
S1-52639778000
S1-52639779000
S1-52639780000
S1-52639781000
S1-52639782000
S1-52639783000
S1-52639784000
S1-52639785000
S1-52639786000
S1-52639787000
S1-52639789000
S1-52639790000
S1-52639791000
S1-52639792000
S1-52639793000
S1-52639794000
S1-52639795000
S1-52639796000
S1-52639797000
S1-52639798000
S1-52639799000
S1-52639800000
S1-52639801000
S1-52639802000
S1-52639803000
S1-52639804000
S1-52639805000
S1-52639806000
S1-52639807000
S1-52639808000
S1-52639809000
S1-52639810000
S1-52639811000
S1-52639812000
S1-52639813000
S1-52639814000
S1-52639815000
S1-52642164000
S1-52642165000
S1-52642166000
S1-52642167000
S1-52642168000
S1-52642169000
S1-52642170000
S1-52642171000
S1-52642172000
TK TANK KEY
TORCH,LP,PENCIL FLAME,TURBOTORCH TP-10
HOSE,TURBO SNAKE TS-12
KIT,SNAKE,TURBO,LP&MAPP TS-1B
CUP,SHIELD,PLASMA CUTTER TSC-25
TOTE,TANK,FOR B TANK TT-150
TT-40 PORTABLE CYLINDER RACK, 40 CU. FT. CYLINDER
TT-150 TANK TOTE B TANK
TIP,CUT,PLASMA (5) FOR TPC-18 T-TIP-18-5
TT-LP TURBOTEST LP
TT-MC TANK TOTE "MC" TANK
TOTE,TANK,MC & R TANKS TT-MCR
KIT,TURBO AIR ACETYLENE
KIT,STARTER,TURBO DAY AIR/FUEL
TURBO EXTREME TX503 PACKAGED
TURBO EXTREME TX504 PACKAGED
TURBO EXTREME TXK504 (FOR 1LBCYL)
TORCH,HAND,SELF-LIGHTING TURBO
PLASMA SYSTEM,1/8" CUTTING TPC-18
KIT,DISPLAY ACETYLENE TURBOTORCH #1 WPDA
KIT,DISPLAY LP TURBOTORCH #2 WPDLP
TX500 PRO PAK(TX-504/T-503 PACKAGED)
KIT,TORCH W/CASE TXC504
TIP,SINGLE FLAME,1/4-7/8" PROVANTAGE V-1
TIP,SINGLE FLAME,1/2"-1" PROVANTAGE V-2
TIP,SINGLE FLAME,5/8 1-1/8 PROVANTAGEV-3
VALVE BODY TURBOTORCH H-4
ADAPTER,MIXER,PROVANTAGE VM-1
TIP,MULTI-FLAME HEATING,PROVANTAGE VMA
NOZZLE,MULTI-FLAME FOR 100 HNDL VMA-1-15
VMA-J-15 MULTI-FLAME NOZZLE (KIT ONLY)
ADAPTER,MIXER,PROVANTAGE VM-J
TIP,WRAPPER,PROVANTAGE 1/2"-1" VW-1
TIP,WRAPPER,PROVANTAGE 5/8"-1-1/8" VW-2
TIP,WRAPPER,PROVANTAGE 7/8"-1-5/8" VW-3
HANDLE,SOF-FLAME,WA-400
KIT,SOF-FLAME,ACETYLENE,MC WSF-3
KIT,SOF-FLAME,ACETYLENE,B WSF-4
X-3B PLUMBING & REFRIGERATION KIT
KIT,ACETYLENE,A/C & REFRIG X-4B
X-5B STARTER KIT
KIT,STARTER X-5MC
X-6MC SERVICEMAN’S KIT-MC
TOTE,PORTABLE W/TANKS M DUTY TTV-100-CPT
KIT,OXY,TURBO W/TANKS LT DUTY TTV-J-APT
TOTE,PORTABLE W/O TANK M DUTY TTV-100-CP
KIT,OXY,TURBO W/O TANKS LT DUTY TTV-J-AP
KIT,OXY,CUTSKILL W/TANKS LT DUTY CST-PT
KIT,OXY,CUTSKILL W/CA & W/TANKS CST-CPT
KIT,OXY,CUTSKILL LESS TANKS CST-P
KIT,OXY,CUTSKILL W/CA LESS TANKS CST-CP
KIT,OXY,CUTSKILL W/CA LESS TOTE CST-150C
KIT,OXY,CUTSKILL LESS TOTE, LESS CA
TOTE, BLACK PLASTIC W/ACCY & ROD STORAGE
0386-1153
0386-1154
0386-1226
0386-0860
0386-1083
0386-0230
1445-0903
1421-0016
1421-0059
1421-0034
1445-0909
0386-0443
1421-0035
1421-0036
0486-0020
0426-0011
0386-1297
0386-1293
0386-1295
0486-0010
1445-0900
0386-0565
0386-0566
0386-1299
0386-1294
0386-0551
0386-0552
0386-0553
0661-0238
0386-0555
0386-0544
0324-0114
0325-0109
0386-0554
0386-0547
0386-0548
0386-0549
0386-0410
0386-0089
0386-0090
0386-0335
0386-0336
0386-0338
0386-0384
0386-0339
0386-1336
0386-1339
0386-1335
0386-1338
0386-1321
0386-1323
0386-1320
0386-1322
0386-1325
0386-1326
1421-0083
75.00
71.43
8.50
53.57
107.14
417.86
110.71
161.25
103.57
129.36
87.50
142.86
121.43
130.04
457.14
738.86
165.79
272.82
457.14
203.57
2735.71
4428.57
3950.00
273.21
246.43
53.57
53.57
53.57
85.71
53.57
75.00
139.29
100.00
64.29
150.00
157.14
160.71
89.29
271.43
239.29
737.79
769.04
592.75
453.57
796.89
1657.14
1125.00
1513.39
807.14
817.86
946.43
661.79
837.86
467.86
450.00
115.25
HVAC Sundries
ABRASIVE CLOTH
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-SC-10
S1-SC-25
ABRASIVE CLOTH - 1-1/2' x 10 YARDS
ABRASIVE CLOTH - 1-1/2' x 25 YARDS
9.14
18.46
296
HVAC Sundries
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-SCM-10
S1-SCM-25
S1-SCM-5
SCREEN,ABRASIVE,GRIP-CUT,1.5"X10YD (M24)
SAND CLOTH, OPEN MESH, 1.5" X 25YD (M12)
SCREEN, ABRASIVE, GRIP-CUT, 1.5"X5YD (M24)
22.07
53.07
13.18
PROTECTIVE GEAR & SUPPLIES
Box Handler Gloves
SOURCE 1 PART NO.
DESCRIPTION
CASE QTY.
MLP $
S1-540-BH1L
S1-540-BH1M
BOX HANDLER GLOVES, SIZE LARGE
BOX HANDLER GLOVES, SIZE MEDIUM
6
6
82.64
82.64
Dust Masks
Extremely lightweight, disposable, nuisance dust mask for non-toxic particles. Metal noseclips to fit individual facial contours.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-5-500
DUST MASKS
50/BOX
24.86
First Aid Kits
10 and 25-unit first aid kits packaged in economy plastic boxes to assist when industrial accidents occur.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-FAK-10
S1-FAK-25
10-UNIT FIRST AID KIT
25-UNIT FIRST AID KIT
51.07
67.71
Nitrile Gloves
Purple, foam control gloves for industrial use that provide a high level of wet and dry grip. Standard in applications where tactile
sensitivity is required.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-540-1005L
NITRILE GLOVES - LARGE
PAIR
15.36
Shoe Covers
Slip these shoe covers on in seconds to protect carpet, tile, or wood from dirt and scuff marks. Customers will appreciate your
professional appearance.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-SC-1
DARK BLUE SHOE COVERS
50 PAIR/BOX
41.57
*M LP per Standard Pack
297
HVAC Sundries
SHOP TOWELS & WIPES
All Purpose Cleaning Pads
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ACP-10
ALL PURPOSE CLEANING PADS - PACK OF 10 PCS
13.86
Boss 892 Industrial Wipes
BOSS ® Industrial Wipes remove the toughest grease, tar, grime, ink, paints, sealants, adhesives and other difficult soils. Each
premoistened wipe is ideal for cleaning heavy-duty soils from hands, tools and work areas. BOSS ® Industrial Wipes are ideal for
general purpose cleaning. Typical applications of BOSS ® Industrial Wipes include automotive service departments, agriculture, field
service trucks, industrial work stations, printing, manufacturing, plumbing and construction. They are ideal for most hard surfaces
including painted walls, tools, work surfaces, signs, siding and bathroom partitions.
Features:
• Pre-moistened
• Contains an advanced formula that removes:
– Silicone
– Acrylic
– Grease
– Enamel
– Glue
– Epoxy
– Ink
– Rubber cement
– Poly foam and much more . . .
– Oil
SOURCE 1 PART NO.
DESCRIPTION
BOSS PART NO
MLP $
S1-BOSS89200
WIPES, INDUSTRIAL, 8 x 12, 100 PCS
03875WH08
31.39
Boss 893 Dual-Sided Abrasive Wipes
BOSS ® Dual Sided Abrasive Wipes remove the toughest grease, tar, grime, ink, paints, sealants, adhesives and other difficult soils.
Each pre-moistened wipe has a textured surface on one side that is ideal for cleaning heavy-duty soils from hands, tools and work
areas. The wipes also have a smooth side for general purpose cleaning. Typical applications of BOSS ® Dual Sided Abrasive Wipes
include automotive service departments, agriculture, field service trucks, industrial work stations, printing, manufacturing, plumbing
and construction. They are ideal for use on most hard surfaces including painted walls, tools, work surfaces, signs, siding and
bathroom partitions.
• Pre-moistened
• Textured weave for added scrubbing power
• Contains an advanced formula and special dual-sided towel that removes:
– Acrylic
– Silicone
– Enamel
– Grease
– Epoxy
– Glue
– Rubber cement
– Ink
– Oil
SOURCE 1 PART NO.
DESCRIPTION
BOSS PART NO
MLP $
S1-BOSS89300
WIPES, INDUSTRIAL, ABRASIVE, 80 PCS
03911WH08
44.96
Boss 894 Biodegradable Wipes
BOSS ® Biodegradable Wipes remove the toughest grease, tar, grime, ink, paints, sealants, adhesives and other difficult soils. Each
premoistened wipe is made of all natural fabric that has been engineered for softness and absorbency to give it a superb towel like
feel. Typical applications of BOSS ® Biodegradable Wipes include automotive service departments, agriculture, field service trucks,
industrial work stations, printing, manufacturing, plumbing and construction. They are ideal for use on most hard surfaces including
painted walls, tools, work surfaces, signs, siding and bathroom partitions.
Features:
• All biodegradable ingredients that are 100% compostable and made without harmful chemicals
• Pre-moistened
• Contains an advanced formula that removes:
– Acrylic
– Silicone
– Enamel
– Grease
– Epoxy
– Glue
– Rubber cement
– Ink
– Oil
SOURCE 1 PART NO.
DESCRIPTION
BOSS PART NO
MLP $
S1-BOSS89400
WIPES, INDUSTRIAL, BIODEGRADABLE, 72 PCS
03981WH08
45.71
298
HVAC Sundries
SHOP TOWELS & WIPES
Kimtex® Towels
Long lasting Kim tex® stands up to oils, chem icals and solvents better than ordinary shop towels. Cloth-like feel and perform ance.
T owel size is 9-3/4” x 16-3/4”. 100 towels/box. 5 boxes/case ®.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-5-33570
KIMTEX SHOP TOWELS
100/BOX
60.46
Shop Towels
Heavy duty reusable towels. For wipe ups of grease, oil, water, etc. 100% cotton material is preshrunk and hemmed. Each towel
measures 13” x 16”.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-ST-10
S1-ST-24
S1-ST-4
SHOP TOWELS
SHOP TOWELS
SHOP TOWELS
10/BAG
24/BAG
4/BAG
22.21
42.43
9.71
Teri Towels
The Teri ® reinforced towels feature multi-ply tissue reinforced with nylon webbing for added strength on the job.
Made from 100% recycled paper. Towel size is 9-3/4” x 16-3/4”. Towel color is white. Comes in a convenient pop up box. 126
towels/box. 10 boxes/case.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-5-34790
TERI REINFORCED TOWELS
126/BOX
25.79
Terry Towels
100% cotton. Minimum of 14” x 17”. Pre-washed for absorbency, fully-hemmed, all-white, and reusable.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-DTT-10
S1-DTT-24
TERRY TOWELS
TERRY TOWELS
10/BAG
24/BAG
15.11
23.79
Workhorse® Manufactured Rags
The economical alternative to scrap rags. Workhorse ® Manufactured Rags is the first product to be made from
®
Kimberly-Clark’s advanced new material – Hydroknit . Durable, rag tough construction stands up to any task. Can be re-used time
and time again. Available in white or blue.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-5-41411
S1-5-41455
9-3/4” x 16-3/4” BLUE
9-3/4” x 16-3/4” WHITE
100/BOX
100/BOX
55.61
50.68
WypAll Plus
Absorbs grease, oil, water and solvents from floors, hands, parts, tools and machinery. T ough enough for extra heavy jobs. Com es in
a convenient pop-up box of 100 towels.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-5-05790
WYPALL PLUS TOWELS—WHITE
100/BOX
28.11
299
HVAC Sundries
SHOP TOWELS & WIPES
WypAll ShopPro X 80 Towels
Like a rental shop towel, only more consistent. Engineered to feel like cloth and work even better. Absorbs more oil and water faster
pound for pound than laundered shop towels. The ShopPro X80 is simply the heaviest duty towel in the Kimberly Clark line. 160
towels/box.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-5-41041
WYPALL SHOPPRO X80 TOWELS
100/BOX
103.14
Markers
VALVE ACTION MARKERS
Large ink supply for increased mileage. Fast drying, smear and water resistant. Utilizes a patented valve activated ink feed
mechanism to supply ink as required, down to the last drop.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-540-800
S1-540-799
VALVE ACTION MARKER-REGULAR TIP – BLACK
VALVE ACTION MARKER-REGULAR TIP – RED
12
12
5.25
5.25
* M LP per each / sol d by the case
VALVE ACTION PAINT MARKERS
Bright, crisp, opaque colors. The oil-based paint is quick drying and permanent on most surfaces. These markers also feature the
patented valve operated feed mechanism and a medium point.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-540-805
S1-540-806
S1-540-807
S1-540-808
VALVE ACTION PAINT MARKER – BLACK
VALVE ACTION PAINT MARKER – RED
VALVE ACTION PAINT MARKER – WHITE
VALVE ACTION PAINT MARKER – YELLOW
12
12
12
12
8.00
8.00
8.00
8.00
300
—NOTES—
301
—NOTES—
302
—NOTES—
303
—NOTES—
304
HVAC System Hygiene
SOURCE 1 COIL & DUCT SPRAY
Features:
• EPA registered fungistat, bacteriostat and germistat for use in HVAC systems
• For use on ductwork, evaporator coils, drip pans and associated air conditioning parts
• Controls microbiological growth and associated odors
• Clean the area, spray thoroughly and allow to dry
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY.
MLP $
S1-H-9532
SPRAY BOTTLE
32 OZ.
12
28.64
*Sold by case/M LP per each
SOURCE 1 COIL-BRITE
Coil Cleaner & Brightener
Features:
• Premium grade alkaline—expanding foam action
• Brightens better than normal alkaline cleaners, Dilution rates from 3 to 40 parts water
• Must be thoroughly rinsed with water, Contains hazardous component Potassium Hydroxide
• Good ventilation, protective gloves, and eye protection required
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY.
MLP $
S1-BM01
S1-BM05
S1-BM55
PREMIUM ALKALINE
PREMIUM ALKALINE
PREMIUM ALKALINE
1 GAL.
5-GAL. PAIL
55-GAL. DRUM
4
1
1
35.57
171.43
1957.11
*Sol d by case/M LP per each
SOURCE 1 E-COIL
Evaporator & Condenser Cleaner
Features:
• No foaming action—only attacks dirt buildup, not metal
• Environmentally safe—cleans without damage to environment, personnel or equipment
• Dilution rates: Condensers—4 parts water, Evaporators—8 parts water
• Rinsing not required on evaporators—normal condensation will carry away dirt and contamination
• May irritate eyes and skin—excessive contact should be avoided
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY.
MLP $
S1-EC01
S1-EC05
S1-EC55
NATURAL COLOR
NATURAL COLOR
NATURAL COLOR
1 GAL.
5 GAL.
55-GAL. DRUM
4
1
1
23.36
116.71
1283.96
SOURCE 1 MP3 COIL CLEANER
Features:
• Acts as a degreaser, detergent, and deodorizer
• Non-acid, multi-purpose
• Triple-action coil and filter cleaner
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY.
MLP $
S1-H-3D01
S1-H-3D55
MP3 ORANGE COIL CLEANER
MP3 ORANGE COIL CLEANER
1 GAL.
55 GAL.
4
1
26.07
1434.89
305
HVAC System Hygiene
SOURCE 1 PRO-FOAM CONCENTRATE
Self Rinsing Evaporator Coil Cleaner
Features:
• Rinsing not required—normal condensation will carry away dirt and contamination
• May irritate eyes and skin—excessive contact should be avoided, Dilution rates from 4 to 6 parts water
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY.
MLP $
S1-401
S1-405
S1-455
GREEN, EVAPORATOR
GREEN, EVAPORATOR
GREEN, EVAPORATOR
1 GAL.
5-GAL. PAIL
55-GAL. DRUM
4
1
1
20.57
102.79
1130.68
NU-CALGON EVAP POW'R®
A revolutionary “no rinse” product formulated for cleaning indoor evaporator coils. It is metal-safe, and cleans and emulsifies even the
most stubborn soils and deposits. Biodegradable. Use concentrate (S1-416808 or S1-416805) at a 3:1 ratio.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-416805
S1-416808
EVAP POW’R-C
EVAP POW’R-C
2.5 GAL.
1 GAL
102.04
41.46
HVAC System Hygiene
SOURCE 1 PRO-FOAM CONCENTRATE ACID
Acid Type, Foaming, Air Cooled Condenser Cleaner & Brightener
Features:
• Expanding foam action
• Best for brightening— makes condenser coils look new
• Dilution rates from 2 to 10 parts water, Must be thoroughly rinsed with water
• Contains hazardous components Hydrofluoric Acid and Phosphoric Acid
• Outdoor use only; protective gloves and eye and face protection required
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY.
MLP $
S1-501
S1-505
S1-555
RED, ACID TYPE
RED, ACID TYPE
RED, ACID TYPE
1 GAL.
5-GAL. PAIL
55-GAL. DRUM
4
1
1
24.93
124.57
1369.61
SOURCE 1 NON-ACID SUPER CONCENTRATE
Features:
• 100% active ingredients
• Super concentrate BASE formulations contain all ingredients to make a coil cleaner suitable for your application—just add water!
• Versatile BASE formulations save money
• Properly dilute with water according to label instructions before use:
— 6–24 parts water for expanding foam on condenser
coils
— 40 parts water (minimum) for heavy duty cleaning of evaporator coils
—80 parts water for electronic filters, blowers, registers and other components
• Excellent on greasy contamination
• Contains hazardous component Potassium Hydroxide
• Must be thoroughly rinsed with water Good ventilation, protective gloves and eye protection required
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY.
MLP $
S1-4X32
NATURAL, ALKALINE
1 QT.
6
17.32
306
SOURCE 1 PRO-FOAM CONCENTRATE NON-ACID
Non-Acid, Foaming, Air Cooled Condenser Cleaner & Brightener
Features:
• Expanding foam action
• Alkaline formulation is excellent on greasy coils
• Dilution rates from 2 to 20 parts water
• Must be thoroughly rinsed with water
• Contains hazardous component Potassium Hydroxide
• Good ventilation, protective gloves, and eye protection required
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY.
MLP $
S1-1101
S1-1105
S1-1155
YELLOW, ALKALINE
YELLOW, ALKALINE
YELLOW, ALKALINE
1 GAL.
5-GAL. PAIL
55-GAL. DRUM
4
1
1
22.86
114.32
1257.61
NU-CALGON NU-BRITE® COOLING COIL CLEANER
It’s a very effective degreaser and cleaner on condenser coils. Its high foaming characteristic will help push soil deposits out of the coil
and leave a clean and bright coil. It can also be used as a kitchen degreaser by emulsifying stubborn, resistive grease deposits found
on coils located in kitchens. Product should be used where thorough rinsing is possible. Biodegradable.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-429101
S1-429105
S1-429108
S1-429118
S1-489108
NU-BRITE COOLING COIL CLEANER
NU-BRITE COOLING COIL CLEANER, CANADA VERSION
55 GAL.
2.5 GAL.
1 GAL.
18 OZ. AEROSOL
2332.75
120.18
45.79
17.39
44.18
SOURCE 1 SELF RINSING EVAPORATOR CLEANER
Non-Acid Condenser Cleaner & Brightener
Features:
• Easy to use aerosol spray cans
• No mixing, no sprayer, no mess
• Ready-to-use
• Zip Foam for condenser coils—must be rinsed with water
• Zip Clean for evaporator coils—no rinsing required
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY.
MLP $
S1-ZC-01
S1-ZC-02
YELLOW, ALKALINE
GREEN, EVAPORATOR
20-OZ. AEROSOL
20-OZ. AEROSOL
12
12
12.04
11.68
NU-CALGON EVAP FOAM® NO RINSE
A high performance, heavy duty coil cleaning detergent. It is formulated with special surfactants and alkaline cleaners that have been
developed into a foaming, no-rinse product. Evap Foam is ideal for use on most coils, but it is particularly suited for use on cooling or
evaporator coils. The aerosol can be sprayed either right side up or upside down.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-417175
EVAP FOAM NO RINSE
18 OZ. AEROSOL CAN
21.11
307
SOURCE 1 SELF RINSING SUPER CONCENTRATE
Features:
• Dilute Self Rinsing Base with 24 parts water—1 quart makes over 6 gallons evaporator cleaner
• Rinsing not required—normal condensation will carry away dirt and contamination
• May irritate eyes and skin—excessive contact should be avoided
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY.
MLP $
S1-SR01
S1-SR32
GREEN, EVAPORATOR
GREEN, EVAPORATOR
1 GAL.
1 QT.
4
6
39.46
15.21
NU-CALGON TRI-CLEAN 2X COIL CLEANER
Features:
• Easy to use. Simply connect to hose, clean, and rinse
• Restores sy stem efficiency by rapidly emulsifying insulating soils from outdoor coil
• A must-have for any clean and check preventative maintenance program
• Cleans where water alone is ineffective
• Metal safe, biodegradable chemistry
• One bottle cleans up to three 5 ton coils
• No sprayer required - eliminating sprayer prep time and cost of sprayer maintenance
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-437224
TRI CLEAN 2X CONDENSER COIL CLEANER
1 QT.
45.04
NU-CALGON ALKA-BRITE®
A non-acid, alkaline based product for brightening and cleaning air cooled condensers. It contains the best available detergents to
quickly penetrate and remove greasy soils and oxidation. Its foaming helps lift greasy soils out of the coil. Biodegradable.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-412008
ALKA-BRITE
1 GAL.
47.07
®
NU-CALGON CAL-BLAST COIL CLEANER
A "no rinse required" coil cleaner in a convenient aerosol package!
Features:
• No rinse required…high solvency cleaning power that evaporates completely
• Most effective on coils found in kitchens
• Quick drying - leaves no residue
• Pleasant citrus scent
• Works great on all soils
• Contains no ozone depleters
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-413220
CAL-BLAST® COIL CLEANER
20 OZ. AEROSOL
24.64
NU-CALGON CAL-BRITE
®
Cal-Brite is a low pH cleaner developed for cleaning evaporator coils, air-cooled condensers and other finned cooling and heating
coils. It is based upon glycolic acid and other ingredients, including DuPont’s surfactant, Merpol. It provides for moderate foaming and
brightening, and is safe for use indoors as well as outdoors.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-413308
CAL-BRITE
1 GAL.
59.75
308
NU-CALGON CALCLEAN®
A heavy-duty liquid alkaline detergent for cleaning evaporator coils, air-cooled condenser coils, metal filters, fan blades and other
surfaces soiled with greasy dust and dirt. Biodegradable.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-408175
S1-413501
S1-413506
S1-413508
CALCLEAN
CALCLEAN
CALCLEAN
CALCLEAN
20 OZ. AEROSOL
55 GAL.
2.5 GAL.
1 GAL.
22.61
2958.04
148.96
58.61
*4-drum m ini mum order
®
NU-CALGON CAL-GREEN CONDENSER CLEANER
Features:
Clean the condenser unit with an all natural environmentally friendly coil cleaner. This non-foaming, non-toxic cleaner is outstanding
for removing dirt and grime which hinders heat transfer. By cleaning the fins with Cal-Green you restore the unit’s efficiency while
being environmentally responsible. This biodegradable product is free and clear of dyes, fragrances, and masking agents.
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
MLP $
S1-419008
COIL & CONDENSER CLEANER
1 GAL.
47.39
®
NU-CALGON EVAP-FRESH CLEANER & DISINFECTANT
Evap-Fresh is a ready-to-use, non-abrasive, one-step cleaner and disinfectant for evaporator coils in small air conditioners,
commercial air handling equipment, HVAC cooling coils and refrigeration equipment.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-416608
S1-416675
EVAP-FRESH
EVAP-FRESH
1 GAL.
18 OZ.
48.39
22.57
NU-CALGON EVAP-GREEN® EVAPORATOR CLEANER
Evap-Green’s outstanding cleaning ability will quickly remove the dust, dirt and debris that is typically found on evaporator coils.
During the cleaning process, dirt, oils and greases are emulsified and are quickly removed from the coil restoring the unit’s efficiency.
Evap-Green is a biodegradable product and does not contain dyes, fragrances, or masking agents. The cleaning agents are derived
from naturally organic builders which supplies a controlled and buffered pH and alkalinity during the cleaning process.
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
MLP $
S1-419108
COIL & EVAPORATOR CLEANER
1 GAL.
44.21
NU-CALGON FOAM BRITE
®
Described as the ultimate foaming alkaline cleaner, Foam Brite is the first in a new generation of condenser coil cleaners. It provides
for excellent cleaning and brightening and at the same time provides for tremendous foaming to push dirt and grime out of the coil.
Foam Brite can be easily used in place of the more dangerous HF acid-based products. Biodegradable.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-417801
S1-417805
S1-417808
FOAM BRITE
FOAM BRITE
FOAM BRITE
55 GAL.
2.5 GAL.
1 GAL.
2566.86
121.11
46.36
*4-drum mi ni mum order
309
NU-CALGON GREEN CLEAN
A pleasantly scented, all-purpose cleaner designed for the rapid removal of grease and other heavy soils. It can be used right out of
the bottle or diluted for milder jobs. Biodegradable
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-418608
S1-418624
GREEN CLEAN
GREEN CLEAN
1 GAL.
1 QT.
49.21
26.79
NU-CALGON NU-BLAST® CONDENSER COIL CLEANER
A “no-rinse formula” condenser coil cleaner in a convenient aerosol package. Double action of high pressure blast and solvent
cleaning restores efficiency of condenser coils. Nu-Blast formula is non-conductive and non-flammable.
SOURCE 1 PART NO.
S1-429075
NU-CALGON SPECIAL HD CALCLEAN
DESCRIPTION
SIZE
MLP $
NU-BLAST CONDENSER COIL CLEANER
18 OZ. AEROSOL
30.07
®
The best cleaner available. It is specifically formulated to remove tobacco tars from electronic air cleaners as well as the most
stubborn deposits from finned coils. Use at a ratio of 5 parts water to 1 part HD CalClean, Biodegradable. This product is also
available in a 6:1 dilution, readyto- use form, CalClean HD-RT U, packaged in quart bottles with spray pump.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-414301
S1-414306
S1-414308
CALCLEAN, SPECIAL HD
55 GAL.
2.5 GAL.
1 GAL.
3359.36
156.71
62.43
*4-drum m ini mum order
NU-CALGON TRI-POW'R®
An outstanding general purpose coil cleaner, providing detergency and degreasing as well as deodorizing capability. Its positive
emulsion technology is very effective versus oily grime, converting the deposits into a more fluid or liquid form that can be easily
rinsed. It is non-acid, non-toxic and biodegradable.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-437188
TRI-POW’R
1 GAL.
33.39
310
HVAC System Hygiene
SOURCE 1 MULTI-RATIO FOAM GUN
Features:
• Automatically mixes cleaning solutions
• 5 adjustable mixing ratio settings
• Excellent for cleaning A/C Condenser Coils
• Quick disconnect for easy rinsing
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY.
MLP $
S1-FG64
MULTI-RATIO FOAM GUN
64-OZ.
1
153.57
Sprayers
NU-CALGON SPRAYERS
Multi-Purpose Sprayer
A 24-ounce capacity sprayer, it’s ideal for small cleaning jobs, such as window units and water coolers.
Cal-Shield® Poly Sprayer
The Cal-Shield ® Poly Sprayer is constructed of high-density translucent polyethylene. It has a funnel top for easy chemical pouring and has a one-gallon
working capacity. It comes with a 10” polypropylene pump, brass handle and extension tube with adjustable nozzle, a wearresistant hose and a pressure relief
®
valve. It is highly recommended that this sprayer be dedicated to Cal-Shield applications only.
No. 50P Poly Sprayer
The No. 50P is constructed of high-density translucent polyethylene. It has a half-gallon capacity (3 pint working capacity). The nozzle is adjustable and the
flow rate is controlled by a thumb lever. It comes with a 7” polyethylene pump.
No. 200P Water Pressurizing Poly Sprayer
The No. 200P Poly Sprayer is constructed of high-density translucent polyethylene. It has a 2-gallon working capacity, funnel top, pump handle and is
equipped with all-brass hardware. Sprayer is pressurized with water through a “quick disconnect” fitting.
No. 220CP & No. 330CP Poly Sprayers
These Sprayers are constructed of high-density translucent polyethylene, incorporating a molded funnel top with a 2-gallon working capacity (3-gallon working
capacity for the 330CP), reinforced 3-foot hose, Buna seals and chemical-resistant wand. Each utilizes a 10” polypropylene pump and an adjustable nozzle.
No. 300P Poly Sprayer
The No. 300P Poly Sprayer is constructed of high-density translucent polyethylene. It has a funnel-top which provides for easy chemical pouring and has a
3-1/2 gallon capacity (3 gallon working capacity). It comes with a 10” Celcon pump, brass extension tube with adjustable nozzle and five feet of vinyl hose.
Coil Gun
A different approach to coil cleaning: a “hoseend” sprayer that features five different mix ratio settings designed for coil cleaners. Utilizes a 2-quart capacity
bottle and includes a foam wand as well as “quick disconnect” capability.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-4768W3
S1-47700
S1-47702
S1-47712
S1-47713
S1-47720
S1-47740
MULTI-PURPOSE HAND SPRAYER
NO. 50P POLY SPRAYER
NO. 100P CAL-SHIELD SPRAYER
NO. 200P WATER PRESSURIZING SPRAYER
NO. 220CP SPRAYER
NO. 300P SPRAYER
COIL GUN
15.64
82.04
147.86
236.57
129.46
206.29
168.75
311
SOURCE 1 SWAT
Bee and Wasp Killer
Features:
• Fast acting
• Kills wasps, bees and hornets on contact
• 20-foot stream provides a safe point of attack
• Dielectric strength over 40,000 volts
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY.
MLP $
S1-200
BEE & WASP SPRAY
16-OZ. AEROSOL
12
13.11
®
NU-CALGON NU-KILL II WASP & HORNET KILLER
A “quick-kill” spray formulation based upon a synergistic formulation of both tetramethrin and permethrin. It instantly and effectively kills wasps, hornets and
yellow jackets, from distances of up to 20 feet. Kills with residual action as wasps and hornets return to their nests. T he formula is safe in and around electrical
equipment, having a dielectric strength of 47,000 volts.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-429275
NU-KILL II WASP & HORNET KILLER
17 OZ. AEROSOL
26.32
SOURCE 1 REFRIGERANT GAS LEAK DETECTOR
Blue, Spray-Type Leak Reactant
Features:
• Pinpoints tiny leaks in pressurized gas systems
• Sprayable, tacky, blue liquid clings to vertical surfaces and the underside of pipes
• Convenient spray for hard to reach areas
• Telltale bubbles indicate leaks
• Non-corrosive, non-clogging
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY.
MLP $
S1-SB-01
S1-SB-32
REFILL
SPRAY BOTTLE
1 GAL.
32-OZ.
4
12
31.07
10.57
312
Gas Leak Detectors
®
NU-CALGON CAL-BLUE & CAL-BLUE® LT GAS LEAK DETECTORS
Cal-Blue is a complete gas leak detector. Not only does it detect the smallest leak, it also provides other significant features and benefits. Its high viscosity
formula enables it to remain in contact with the applied surface for an extended period of time, thereby allowing the smallest of leaks to be detected. It is also
noncorrosive to metal and it will not affect ultraviolet or “black lights.” Additionally, it is free zeprotected to 5°F and safe for use on most gases, including
oxygen. Cal-Blue LT is the same high quality formulation as regular Cal-Blue, but has added freeze protection to -20°F. It is the ideal detector for those
geographical areas that experience very cold temperatures.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-418208
S1-418224
S1-418253
S1-418308
S1-418324
CAL-BLUE GAS LEAK DETECTOR
CAL-BLUE LT GAS LEAK DETECTOR
CAL-BLUE LT GAS LEAK DETECTOR
1 GAL.
1 QT.
6 OZ.
1 GAL.
1 QT.
51.36
19.11
10.75
70.75
27.68
NU-CALGON FLUORESCENT GAS LEAK DETECTOR
A fluorescent formulation that provides improved visibility and long lasting bubbles. It is non-corrosive to metals and is freeze
protected to 0°F. Suitable for high and low temperature applications. Can be used for most refrigerants, natural gas and oxygen
sy stems.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-418408
S1-418424
S1-418453
FLUORESCENT GAS LEAK DETECTOR
1 GAL.
1 QT.
8 OZ.
56.64
28.04
11.61
NU-CALGON GAS LEAK DETECTOR
A high viscosity liquid that forms bubbles when daubed on a gas leak. Non-corrosive, non-staining, harmless to skin. Detects any type
of gas leak such as air, compressed air, CO2, nitrogen, natural gas and refrigerant gases. Freeze point is well below 0°F. Six ounce
plastic bottles have dauber in cap.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-418053
GAS LEAK DETECTOR
6 OZ.
15.82
HVAC System Hygiene
SOURCE 1 EVERCLEAN COIL COAT
Cooling Coil Anti-Foulant
Features:
• Water based anti-foulant for cooling coils
• Forms microscopically thin coating that renders cooling surfaces self-cleaning for up to two years
• Prevents fungus and similar organisms from growing in the coating
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY.
MLP $
S1-9901
S1-9932
REFILL
SPRAY BOTTLE
1 GAL.
32 OZ.
4
12
61.50
28.39
313
HVAC System Hygiene
SOURCE 1 FIN PROTECTANT
Condenser Coil Coating
Features:
• Ideal for use on air-cooled condensers located in corrosive environments such as paper mills, chemical plants, airports, adjacent to
freeways and salt air areas
• Acrylic polymer coating protects aluminum, copper, brass, bronze, chrome, galvanized metal, titanium and stainless steel
• Easy to use aerosol or 1-gallon can for larger job
• Economical and easy to apply in the field
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY.
MLP $
S1-A-7901
S1-B-7900
S1-B-7901
BLUE TINT AEROSOL
CLEAR
BLUE-TINT
20-OZ.
1 GAL.
1 GAL.
12
4
4
30.89
80.32
80.32
Coil Protection
NU-CALGON CAL-SHIELD
®
Cal-Shield is a synergistic liquid formulation based upon DuPont’s Teflon® fluoroadditives. It is specifically designed for application on
air-cooled condensers, evaporator coils and other finned heating and cooling coils where it forms a micro-thin or molecular film of
Teflon. Once applied, Cal-Shield will shield and protect the coil from adverse conditions within the operating environment.
Features:
• Ready-to-use product
• A food-grade product, made with FDA-approved ingredients
• Forms a micro-thin protective shield that does not affect heat transfer
• Reduces the ability of dirt and grime to adhere, making next cleaning easier
• Extends life of coils operating in corrosive environments such as salt air and food acids
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-414808
S1-414832
CAL-SHIELD WITH TEFLON
CAL-SHIELD WITH TEFLON
1 GAL.
1 QT.
146.93
60.68
BRONZ-GLOW TECHNOLOGIES HVAC/R CORROSION PROTECTION PRODUCTS
Green-Fin Aerosol Kit
A Complete Coating System for Coils & Components of Small Tonnage HVAC/R Equipment
The “Green-Fin” Kit is designed for providing quality corrosion protection for residential systems, PTAC’s, window units etc. A cost
effective solution for effective corrosion protection on new or existing equipment with minor corrosive damage. On average the kit will
provide coverage for 15 - 17 square feet of coil face area. This product is recommended for coils not greater than two rows in depth
with fin spacing of 17 fins per inch or less. Successfully used in environments such as: Coastal, Paper Mills, Waste Water Treatment
Plants, Oil Refineries, Veterinary Facilities, Restaurants, Food Processing Plants, Hospitals etc.
KIT CONTENTS:
1 15.5 oz. Solvent Cleaner
2 15.5 oz. Primer
3 14.5 oz. “Green-Fin”
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-51303082000
COMPLETE KIT - 4 CANS
4 KITS/CARTON
174.71
* Sol d by Standard Pack / M LP per each
314
WAGNER PRODUCTS COIL GUARD
For Protection of Coils and Housings From Rust and Corrosion
Coil Guard is ideally used in coastal areas where salt air accelerates rust and decay of A/C and refrigeration equipment. It is,
however, highly recommended for use in all geographical areas to prolong the life of a unit and to protect condensers against
industrial pollutants and oxidation. When applied properly, Coil Guard dries quickly, and immediately resists salt spray, alcohol, acids,
and soap solutions. Weather will not blacken it. Coil Guard has high dielectric properties AND HAS NO EFFECT ON HEAT
TRANSFER.
Features:
• Protects against industrial pollutants, salt, acids, etc.
• Ideal for evaporator coil protection in food service applications
• Effective on all coils up to 24 fins/inch
• Protects evaporator coils against the build-up of the sources of Dirty Sock Syndrome
• Clear
SOURCE 1 PART NO.
MODEL NO.
SIZE
COLOR
MLP $
S1-01302983700
C-20
20 OZ.
CLEAR
44.61
IAQ Assurance
®
NU-CALGON BIO-FRESH CD
A ready-to-use product that is bacteriostatic, fungistatic and a deodorizer based upon chlorine dioxide technology. It is recommended
for control of bacteria, mold, mildew, fungi and yeasts in IAQ applications, and it is safe for fogging and may be applied to occupied
space. Its EPA registration includes application to HVACR ventilating equipment, including coils, condensate pans, filters and
ductwork. It has also been tested and found to be effective against Legionella bacteria. It can be applied easily by spraying, brushing,
sponging, wiping or fogging.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-412634
S1-412638
BIO-FRESH CD
BIO-FRESH CD
1 QT.
1 GAL.
29.25
49.68
NU-CALGON BIO-FRESH® FOGGER
The Bio-Fresh Fogger is made of a one-piece, seamless heavy-duty copolymer. It uses a 48” flexible hose and it is adjustable from 0–
18 oz. per minute with the respective particle size at 20–80 microns.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-46930
BIO-FRESH FOGGER
1270.43
NEUTRONIC ODOR NEUTRALIZER
Features:
• Neutralizes malodors without the use of heavy perfumes
• Use in air ducts or anywhere foul odors are present
• Hotels, apartments, homes, RVs, boats, hospitals, bathrooms, etc.
• Remove gel from container and place on lid
• Neutralizes malodors without the use of heavy perfumes
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY.
MLP $
S1-H-NT03
S1-H-NT08
NEUTRONIC
NEUTRONIC
3 LBS.
8 OZ.
4
18
37.29
9.46
* S ol d by the Case/M LP per each
315
ODOR NEUTRALIZER
CherryAir Odor Neutralizer
CherryAir Odor Neutralizer removes odors quickly and permanently leaving a pleasant Cherry fragrance behind.
Using unique ClenAir odor neutralizing technology, Cherry-Air is a true odor eliminator - not an odor mask like
many scented products. Cherry-Air attacks odors caused by fuel oil, smoke, pets, mold and mildew, cigarette
and cigar smoke, decay, cleaning solvents, and even skun ks!
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-NC-61010
S1-NC-61011
S1-NC-61013
S1-NC-61015
S1-NC-61017
S1-NC-61018
1/2 lb. Tub (Display Box)
1 lb. Tub
3 lb. Tub
10 lb. Tub
30 lb. Tub
Mini Tub
12
12
4
2
1
18
15.07
24.75
62.43
171.86
503.36
7.61
ClenAir HVAC Odor-Block
ClenAir HVAC Odor-Block is not a perfume mask or cover-up. The unique ClenAir formula molecularly reacts
with the airborne odor-causing compounds and eliminates them and other indoor pollutants leaving clean, fresh,
air behind. The HVAC Odor-Block makes it easy to remove odors and improve the indoor air quality in the entire
home or building by treating the air through the HVAC system.
Eliminates odors caused by mold, mildew, bacteria, pets, smoke, musty odors, water damage, fire damage,
paints, chemicals, animal decay, stale air, garbage areas, sewer gases, skunks, and more!
Use in A/C units, furnaces, rooftop units, fan coil units, and air handlers. Residential HVAC Odor-Block treats up
to 3 ton systems for 2 months. Commercial HVAC Odor-Block treats 10 to 15 ton systems for 4 months.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-NC-61060
S1-NC-61061
Residential HVAC Odor-Block
Commercial HVAC Odor-Block
6
2
42.75
113.29
316
ODOR NEUTRALIZER
ClenAir Odor Neutralizer
ClenAir Liquid Formula
Liquid ClenAir is a fast acting deodorizing product. Eliminates odors via an oxidation process while leaving a
fresh scent. Applications include HVACR ventilating equipment including evaporator coils. Duct work and
condensate pans. Also can pour down drains, garbage disposals and in trash cans. Spray in restrooms, locker
rooms and on fouled carpeting, upholstery. Used by hospitals, nursing homes, HVACR technicians. Non-Toxic &
Environmentally Friendly!
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-NC-61030
S1-NC-61031
S1-NC-61033
S1-NC-61035
S1-NC-61037
S1-NC-61038
Unscented Spray 16 oz.
Unscented Liquid 1 Gal.
Citrus Spray 16 oz.
Citrus Liquid 1 Gal.
CherryAir Spray 16 oz.
CherryAir Liquid 1 Gal.
12
4
12
4
12
4
18.25
43.14
18.79
43.86
18.79
43.86
ClenAir’s unique odor neutralizing formula removes odors quickly and permanently. Originally designed for use
in central air systems, on fire and flood restoration jobs and in sewage facilities, ClenAir is a professional
product, yet it leaves no lingering antiseptic or perfume smell. Use ClenAir gel to combat stubborn odor, even
those that have built up over time like cigarette odor or pet odors. Simply place the gel near the source of the
odor or in the return duct of your central air system. The best product available for musty basements. Great for
smoke and water damage as well as pet odors. Used by heating and air conditioning technicians, professional
duct cleaners, janitors and property management.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-NC-61000
S1-NC-61001
S1-NC-61002
S1-NC-61003
S1-NC-61004
S1-NC-61005
S1-NC-61006
S1-NC-61007
S1-NC-61008
Mini Tub
1/2 lb. Tub
1 lb. Tub
3 lb. Tub
10 lb. Tub
30 lb. Tub
Wall Unit (white)
1 lb. (Gel Brick for wall unit)
18
12
24
12
4
2
1
1
12
7.61
15.07
14.86
24.75
62.43
171.86
503.36
34.93
21.14
317
ODOR NEUTRALIZER
OrangeAir Odor Neutralizer
OrangeAir - Using the unique ClenAir odor neutralizing technology, OrangeAir safely eliminates odors leaving a
refreshingly crisp Orange fragrance behind. OrangeAir is not a mask or cover-up. It is a true odor eliminator.
OrangeAir eliminates odors caused by smoke, pets, fuel oil, mold, mildew, bacteria, cigarette smoke, water
damage, fire damage, stale air, decay, chemicals, even skun ks! Amazing Results!
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-NC-61020
S1-NC-61021
S1-NC-61023
S1-NC-61025
S1-NC-61027
S1-NC-61028
1 lb. Tub
3 lb. Tub
10 lb. Tub
30 lb. Tub
Mini Tub
12
12
4
2
1
18
15.07
24.75
62.43
171.86
503.36
7.61
IAQ Assurance
NU-CALGON PAN-SPRAY LEAK SEALER
Pan-Spray is a quick and easy to use waterproof rubberized coating that won’t chip, flake or peel. It’s ideal for sealing out rust and
corrosion as well as leaky condensate pans, cooling towers, swamp coolers, roofing, gutters and downspouts. Pan-Spray is the
perfect solution for emergency and permanent repair. Dries in about 30 minutes and one can will cover 20 square feet.
SOURCE 1 PART NO.
DESCRIPTION
COLOR
SIZE
MLP $
S1-429650
S1-429651
PAN-SPRAY LEAK SEALER
PAN-SPRAY LEAK SEALER
BLACK
WHITE
16 OZ.
16 OZ.
43.04
43.04
318
Condensate Drain Pan Strips, Tabs & Lubricants
Condensate Pan Strips
PurCool Green Strips
PurCool Green strips and tablets prevent slime and sludge build-up in air conditioning and refrigeration condensate drain pans. They
utilize unique, environmentally friendly plant based suspending and dispersing action to prevent build-ups, overflows, and odors in
drain pans. When placed in the drain pan, PurCool Green will slowly dissolve in the condensate water providing preventative
treatment for 4-6 months. PurCool Green does not contain any harsh chemicals or biocides, making them safer for the user and the
environment
Use in all A/C air handlers, fan coil units, window units, mini splits, and refrigeration condensate drain pans.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-NC-61044
S1-NC-61045
S1-NC-61046
PurCool Green Strips - Mini Strip
PurCool Green Strips - 10 Ton Commercial Strip
PurCool Green Strips - 30 Ton Commercial Strip
12
12
12
13.68
22.46
55.39
PurCool Strips
PurCool Strips are powerful, economical, preventive maintenance for A/C condensate drain pans. Just place them anywhere in the
drain pan where the PurCool Strips will contact the condensate water and enjoy up to six months of economical protection. PurCool
Strips will adhere to the drain pan and will not float or move. They dissolve completely, leaving no residue. Safe for metal and plastic
drain pans.
PurCool Strips keep A/C and refrigeration condensate drain pans clean and free flowing. Use PurCool Strips to prevent condensate
drain clogs, costly overflow, and corrosion.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-NC-61040
S1-NC-61041
S1-NC-61042
S1-NC-61043
S1-NC-61047
PurCool Strips - Treats 30 tons for 6 months
PurCool Strips - Treats 3 tons for 6 months (bulk)
12
12
12
12
100
49.25
20.11
11.43
9.57
8.46
HYDRO BALANCE STA-CLEAN
Condensate Pan Strips
Features:
• EPA registered, timed-release control of microbial contaminants in condensate pans
• Kills mold, algae, fungus and other microorganisms
• Lasts up to 6 months
• Place in drain pan as far from drain as possible
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY.
MLP $
S1-CS-100
S1-CS-50
UP TO 2.5 TONS
WINDOW/FAN & COIL UNITS
1 EACH
1 EACH
12
12
15.64
9.25
319
Condensate Drain Strips, Tabs & Lubricants
CONDENSATE PAN OVERFLOW PROTECTION
A/C Drain Sucker
A/C condensate drain pan overflows are a very common and costly service problem. The overflows are caused by slime and sludge
that builds up and clogs the drain line. The A/C Drain Sucker quickly removes the clog and excess water, resolving the overflow
problem. The kit also includes PurCool® Shock Tablets to clean and treat the remaining slime and sludge in the pan and lines, as well
as a PurCool® Pan Strip to provide months of preventive treatment and free flowing drains.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-NC-61308
A/C Drain Sucker Kit
6
69.04
Condensate Pan Tabs
Purcool Green Tablets
PurCool Green strips and tablets prevent slime and sludge build-up in air conditioning and refrigeration condensate drain pans. They
utilize unique, environmentally friendly plant based suspending and dispersing action to prevent build-ups, overflows, and odors in
drain pans. When placed in the drain pan, PurCool Green will slowly dissolve in the condensate water providing preventative
treatment for 4-6 months. PurCool Green does not contain any harsh chemicals or biocides, making them safer for the user and the
environment
Use in all A/C air handlers, fan coil units, window units, mini splits, and refrigeration condensate drain pans.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-NC-61051
S1-NC-61052
Green Tablet (one tablet)
Green Tablet (bulk)
12
100
13.32
11.79
Purcool Tablets
PurCool Tablets utilize a powerful formulation to keep condensate drain pans clean and free flowing, eliminating problems caused by
plugged condensate drain pans and lines. Use PurCool Tablets to remove sludge and slime in A/C condensate pans, to prevent
overflows and the costly water damage caused by such overflows. PurCool tablets are safe when used as directed. They are
completely soluble in water, biodegradable, and will not leave any deposits on surfaces.
PurCool Tablets will control clogs, build up, odors, and corrosion in drain pans, condensate pumps, and humidifiers. Also approved for
computer room humidifiers.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-NC-61053
S1-NC-61054
PurCool Tablets (200 tablets)
PurCool Shock Tabs
12
24
40.79
6.71
320
SOURCE 1 DRAIN TABS
For Condensate Drain Pans
Helps control odors, overflows and water damage.
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY.
MLP $
S1-CT-200
PAN-CLEAR
200-CT. JAR
12
37.43
IAQ Assurance
NU-CALGON GEL-TABS DRAIN PAN TREATMENT
Features:
• Protects drain pan against clogs
• Gel formulation locks tab into place
• Completely dissolves
• Up to 3 months of protection
• Eliminates foul & musty odors
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-418503
S1-418505
S1-418515
S1-418520
GEL-TABS
GEL-TABS
GEL-TABS
GEL-TABS
3-TON
5-TON
15-TON
20-TON
39.57
47.04
33.14
42.36
NU-CALGON PANPADS®
A revolutionary package-design of a product formulated especially to eliminate the buildup of bacteria and slime growths in air
conditioning and refrigeration condensate drain pans. Combats a broad spectrum of harmful bacteria, including Legionella. Each size
will provide adequate treatment for up to 6 months.
SOURCE 1 PART NO.
DESCRIPTION
TREATS SYSTEM SIZE (UP TO)
SIZE
MLP $
S1-429534
S1-429536
S1-429624
S1-429645
PANPADS
PANPADS
PANPADS
PANPADS
5-TON
5-TON SLIM
15-TON
45-TON
3/4 OZ.
3/4 OZ.
2-1/8 OZ.
6 OZ.
12.32
12.32
31.00
67.89
NU-CALGON PAN-TREATTM CONDENSATE PAN TABLETS
Left untreated, condensate pans can suffer from the build-up of sludge, scum and other accumulations. This build-up can cause odors
as well as plugged drains and overflows, which in turn result in water damage. Pan-Treat is formulated with ingredients proven
effective in cleaning and preventing these deposits, and its use will eliminate the extra maintenance costs associated with odors,
plugged drains and overflows. Pan-Treat is extremely easy to use, and is safe, non-corrosive, non-toxic and biodegradable. The
product is completely soluble in water and it does not form any deposits in the pan or drain.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-429660
PAN-TREAT CONDENSATE PAN TABLETS
50.43
DIVERSITECH LINESEALTM
LineSeal™ is a patented, contaminate free sealing solution for refrigerant systems. Seals leaks and provides years of protection
against future leaks.
SOURCE 1 PART NO.
S1-LS-1
S1-LS-2
DESCRIPTION
ORDER MULTIPLE
MLP $
LINESEAL , 1-OZ CAN - UP TO 1.5T SYSTEM
6
6
119.00
150.79
TM
LINESEALTM, 3-OZ CAN - 1.5-5T SYSTEM
321
DIVERSITECH PRO-FLUSH HVACTM FLUSHING SOLVENT
A flushing solvent for A/C and refrigeration systems formulated for R-410A retrofits, refrigerant conversions and compressor burnouts.
Compatible with all refrigerants and compressor oils. All solvents in Pro-Flush are non-VOC and conform to EPA SNAP standards:
low toxicity, non-flammable, residue- free. Pro-Flush is available as a kit or in a 16 oz. solvent refill. The kit makes servicing quick,
easy, and safe, as well as assuring you get to the job site with all necessary hardware in hand for 1- stop servicing. The kit includes:
16 oz. container of Pro-Flush solvent, refillable Pro- Flush injector tool pressure tank, pressure relief valve for added safety, large
rubber adapter that flushes up to1-1/4” line sets, service hose.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-PF-16
S1-PF-KIT
PRO-FLUSH HVAC FLUSHING SOLVENT REFILL
PRO-FLUSH HVAC FLUSHING SOLVENT KIT
150.34
284.14
System Flushing
NU-CALGON FLUSHING TOOL FOR RX11 LINESETS
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-430050
FLUSHING TOOL FOR RX11 LINESETS
26.64
NU-CALGON RX11-FLUSH®
Rx11-flush is an ozone-safe solvent engineered specifically for flushing refrigeration and air conditioning systems. Rx11 is strong enough to rinse away
particulate, sludge, carbon residues, acids, oils and water. It enhances sy stem service and avoids the need for time-consuming repeat visits. Rx11-flush should
be an integral part of standard procedures for any major system repair, oil changeout or retrofit.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-430008
S1-430009
S1-430010
S1-430011
S1-430015
S1-430026
S1-430030
S1-430038
S1-430051
S1-430052
S1-430089 *
RX-11 FLUSH, STARTER PACK
RX11-FLUSH (3–4 TON)
RX11-FLUSH “2-IN-1” DISPLAY
RX11-FLUSH (5–7 TON)
RX11-FLUSH
RX-11 FLUSH, 26-LB CYLINDER
RX-11 FLUSH, 19.5-OZ CAN
RX-11 FLUSH, KIT, LIQUID
RX-11 FLUSH, GUN
RX-11 FLUSH, HOSE
RX11-FLUSH INJECTION TOOL
253.54
121.89
535.96
234.29
1385.11
2631.96
121.89
274.96
72.96
53.71
77.89
* Also fi ts Pneu-fl ush.
322
System Flushing
Nu-Calgon Rx11-Flush® Injection Valve
The Rx11-flush Injection Valve screws directly to the can and attaches to the Rx11-flush Hose to inject the product into a system. It is
reusable and since it does not pierce the can, product can be used on multiple jobs once the valve is removed.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-430089
TOOL,INJECTION,RX11 SYSTEM FLUSH
76.82
System Protection
NU-CALGON A/C RE-NEW
A/C Re-New Injector Tool
The A/C Re-New Injector was designed to inject A/C Re-New into air conditioning and refrigeration systems. It has a capacity of 4 fl.
oz. and can be used for other injectable products as well, including amounts less than the 4 fl. oz. capacity. It is constructed of rugged
aluminum and has a maximum working pressure of 600 psi. It has a Schrader fitting at one end and a short length of hose with a ball
valve on the other end.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-405799
TOOL,INJECTOR,AC-RENEW
259.25
®
A/C Re-New, formerly Zerol Ice, has been used successfully for many years to improve the performance of air
conditioning and refrigeration systems. A/C Re-New provides significant saving in energy use. It also quiets noisy sy stems and
extends the life of the system. It is a lubricant that blends with the system’s oil, lasting for the life of the equipment.
Features:
• Quiets noisy compressors.
• Reduces energy consumption.
• Improves heat transfer in the evaporator and condenser.
• Great for new and old systems.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-405750
S1-405752
A/C RE-NEW, PRESSURIZED CAN (M6)
A/C RE-NEW, DISPLAY PACK
179.71
414.75
NU-CALGON EASYDRY
A/C EasyDry eliminates moisture in the system
Features:
• Treats 1.5 to 5 ton systems
• Compatible with all oils and refrigerants
• Prevents acid from forming
• Complements the system’s drier
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-405106
MOISTURE REMOVER, EASY DRY, 3-OZ
129.11
323
System Protection
NU-CALGON EASYSEAL
A/C EasySeal is designed to prevent as well as repair leaks anywhere in the system, including condensers,
evaporators, copper lines, and soldered joints. It is easily injected into the system, traveling with the refrigerant,
searching for leaks. It will react with moisture and air that are naturally present at a leak, forming a secure seal.
A/C EasySeal is compatible with the refrigerant, oil and all system materials and it will not react until it comes into contact with the air
and moisture at the leak, forming a seal.
Benefits:
• Prevents refrigerant leaks and seals existing leaks in air conditioning and refrigeration systems
• Eliminates expensive leak search and repair
• Travels with refrigerant to find leaks fast
• Ultilizes a re-usable hose.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-405002
S1-405006
S1-405199
SEALANT, A/C EASY SEAL, DISPLAY PACK
SEALANT, A/C EASY SEAL
VLV,PIERCING, W/ HOSE, FOR A/C EASY SEAL
295.14
129.11
36.25
TEST ALL ACID TEST KIT
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-780042
KIT,TEST,ACID,TA-1
24.04
UNIVERSAL ACID TEST KIT
For use with both mineral and POE Oils.
Application:
The Universal Acid Alert Test Kit provides a positive indication of whether the acid level of the refrigeration oil is safe or unsafe.
Features:
Quick and easy test kit
Universal acid test kit for use with all refrigeration lubricants
By changing the percentage of oil sample taken, the acid number of the oil can be accurately determined.
Phase separation of the chemicals in the kit provide a positive color change regardless of the color and condition of the oil.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-064427
AA KIT UNIVERSAL
27.61
SOURCE 1 ACID NEUTRALIZER
Features:
• Neutralizes and scavenges acid and moisture from air conditioning and refrigeration systems
• Use for preventative maintenance and after burnouts
• Safe for system
• No harmful residues
• No by-products
• Suitable for use with all lubricants - mineral, alkylbenzene, and polyol ester
SOURCE 1 PART NO.
PACKAGE
CASE/ORDER QTY.
MLP $
S1-H-3702
2 OZ.
6
29.64
324
Lubricant Products
NU-CALGON RX-ACID SCAVENGERTM
A better, more convenient way to neutralize or “scavenge” acid in refrigeration or air conditioning systems after burnouts or during
normal ongoing system maintenance. Normal dosage rate is 2 fl. oz. of Rx-Acid Scavenger for every one gallon of system oil—50%
less than other acid neutralizing products. This “low treat” feature means far less material has to be added to the system. In addition,
the Rx-Acid Scavenger can be used with all lubricants: mineral, alkylbenzene and polyol ester. This means only one product in the
tool box or on the truck for all acid neutralizing needs.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-430102
S1-430105
RX-ACID SCAVENGER
RX-ACID SCAVENGER,PRESSURIZED CAN
54.93
54.93
325
NU-CALGON PH TREAT
TM
ACID NEUTRALIZER KIT
For Neutralizing Condensate from High Efficiency Furnaces, Boilers, and Tankless Water Heaters
Features:
• Contains a specialized media that neutralizes the condensate water, raising the pH to near neutral
• 2.5˝ X 12˝ cartridge housing with 3/8˝ FPT connections
• Packaged with two each 1/2˝ barb fittings x 3/8˝ MPT fittings
• Packaged with two each 3/4˝ FPT x 3/8˝ MPT fittings
• Packaged with 1 each C-clip for mounting
• Designed for gravity feed
• Product life is expected to have a One Year service life, or when the pH falls below 6
• Temperature range 40ºF to 100ºF
• Pressure range 0-125 psi
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-472006
KIT,ACID NEUTRALIZER,PH TREAT (M6)
124.86
SOURCE 1 MINERAL OILS
Hydro-Balance POE Lubricants
ISO-100 Synthetic Ester
SOURCE 1 PART NO.
VISCOSITY
PACKAGE
CASE QTY
MLP $
S1-E-10001
S1-E-10032
100
100
1-GAL
32-OZ
6
12
202.82
60.89
SOURCE 1 PART NO.
VISCOSITY
PACKAGE
CASE QTY
MLP $
S1-P-22001
S1-P-22032
220
220
1-GAL
32-OZ
6
12
191.04
59.14
SOURCE 1 PART NO.
VISCOSITY
PACKAGE
CASE QTY
MLP $
S1-E-6801
S1-E-6832
68
68
1-GAL
32-OZ
6
12
186.96
57.93
SOURCE 1 PART NO.
VISCOSITY
PACKAGE
CASE/ORDER QTY.
MLP $
S1-2401
300 SUS
1 GAL.
6
50.07
326
SOURCE 1 Z-LUBES
Alkylbenzene Refrigeration Lubricants
Features:
• High quality reliable lubrication
• High solubility—Low foaming—Low floc point
• Excellent thermal stability
• OEM approved
• Compatible with CFC & HCFC refrigerants and mineral oils
• Filtered to 1 micron for high purity
SOURCE 1 PART NO.
VISCOSITY
PACKAGE
CASE/ORDER QTY.
MLP $
S1-Z150-01
150 SUS
1 GAL.
6
57.64
HYDRO BALANCE SYNTHETIC ESTER LUBRICANTS
Features:
• Excellent lubricating properties over a wide temperature range
• OEM Approved
• Specially formulated for use with HFC refrigerants
SOURCE 1 PART NO.
VISCOSITY
PACKAGE
CASE/ORDER QTY.
MLP $
S1-P-6801
S1-P-6832
ISO 68 (300 SUS)
ISO 68 (300 SUS)
1 GAL.
1 QT.
6
12
164.21
48.46
Refrigeration Oils
NU-CALGON C-3 & C-4 REFRIGERATION OILS
Mineral Oils (MO)
These are mineral naphthenic lubricants. They are available in two viscosities:
C-3 (RO15) = 150 SUS
C-4 (RO30) = 300 SUS
They are specifically designed for today’s high performance air conditioning and refrigeration compressors. These modern
compressors run at higher speeds and generate higher temperatures so they require better lubrication. Use of these oils will insure
continued efficient operation, providing the important properties required from an efficient refrigeration oil: good lubrication, good
stability and good low temperature performance.
OEM Approvals: Copeland and Tecumseh, among thers.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-430305
S1-430307
S1-430405
S1-430407
S1-430507
C-3 REFRIGERATION OIL
5 GAL.
1 GAL.
5 GAL.
1 GAL.
1 GAL.
348.57
70.64
349.54
71.32
70.64
NU-CALGON CAN-VERTER® OIL PUMP
A hand-held pump used to remove oil from and add oil to hermetic compressors. Easy to use; each stroke pumps 1 oz. of oil.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-48140
PUMP, OIL, CANVERTER
214.11
327
Refrigeration Oils
NU-CALGON EMKARATE RL LUBRICANTS
Polyol Ester Oils (POE)
These lubricants are designed specifically for use with the HFC refrigerants, and they have been developed to meet the performance
demands of the refrigeration industry. The polyol ester base fluids are specifically formulated for optimum performance with minimal
additive levels.
These Emkarate lubricants are available in a range of viscosities to suit most refrigeration applications. Their higher viscosity index
(VI) minimizes energy consumption at low temperatures and maximizes lubrication at elevated temperatures. The lubricants have
excellent thermal and chemical stability, and are compatible with a range of elastomers, polymeric materials and other material s of
construction. They are fully miscible and compatible with mineral oils and alkylbenzene lubricants as well as with CFCs, HCFCs and
HFCs. Thus, they are an excellent choice for retrofitting existing equipment.
OEM Approvals: Various viscosities of the Emkarate RL lubricants are approved by all major OEMs, including Copeland and
Tecumseh.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-431446
S1-431464
S1-431465
S1-431466
S1-431645
S1-431646
S1-431825
S1-431826
S1-431866
EMKARATE RL 32H REFRIGERATION OIL
EMKARATE RL32-3MAF REFRIGERATION OIL
ICI RL68H REFRIGERATION OIL
ICI RL68H REFRIGERATION OIL
EMKARATE RL 170H REFRIGERATION OIL
EMKARATE RL 170H REFRIGERATION OIL (M4)
EMKARATE RL 220H+ REFRIGERATION OIL (M4)
1 GAL.
1 QT.
5 GAL.
1 GAL.
5 GAL.
1 GAL.
5 GAL.
1 GAL.
1 GAL.
215.93
68.86
958.11
206.86
1071.93
218.43
1379.68
272.11
256.82
NU-CALGON TOTAL LUBE REFRIGERATION OIL TEST KIT
Use Nu-Calgon's Total Lube oil Analysis Test Kit to stay on top of the management of your refrigeration oil needs. Simply visit your
local HVAC wholesaler and purchase the Nu-Calgon Total Lube Oil Test Kit and fill it with the oil in which you want analysized. Mail it
to the enclosed address and within a few days you'll receive a comprehensive report providing you with all the pertinent information.
Features:
• Timely and accurate
• Use with Mineral Oil, Alkylbenzene Oil and POE lubricants
• Reduces downtime and costly oil changes
• Avoid system failures and burnouts
• Secure metal container for oil sample
• Durable mailer
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-49960
REFRIGERANT,TOTAL LUBE,TEST,KIT
185.79
NU-CALGON ZEROL® REFRIGERATION OILS
Alkylbenzene Oils (AB)
Zerol Refrigeration is a high quality, synthetic alkylbenzene refrigeration oil. It is similar in many ways to natural mineral oil but has
superior properties that make it particularly valuable in refrigeration and air conditioning applications. It is available in three viscosities:
Zerol 150 = 150 SUS
Zerol 200TD = 200 SUS
Zerol 300 = 300 SUS
Zerol Refrigeration Oil is recommended for use in all refrigeration and air conditioning applications using CFC and HCFC refrigerants.
It is highly recommended by refrigerant and compressor manufacturers for use with the HCFC blends such as R401A and R409A as it
provides many distinct advantages: excellent miscibility, thermal stability and compatibility with mineral oils. It is the oil of choice for R22 and R-502. It is also an excellent clean-up/flushing oil.
OEM Approvals: Copeland (Zerol 200TD), Danfoss, Tecumseh and Bristol, among others.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-430805
ZEROL 200TD REFRIGERATION OIL
5 GAL.
617.14
S1-430807
S1-431007
S1-431107
ZEROL 200TD REFRIGERATION OIL
ZEROL 150 REFRIGERATION OIL
ZEROL 300 REFRIGERATION OIL
1 GAL.
1 GAL.
1 GAL.
118.79
114.89
149.00
328
SOURCE 1 VACUUM PUMP OIL
Features:
• Highly demulsifiable—separates from water in 25 minutes at 180°F
• Loosens dirt and sludge and cleans pump
• Combination of additives makes for true anti-wear lubricant and lengthens pump life
• Anti-rust ingredient protects internal parts
• Convenient flip-top on quart bottle
• Filtered to 1 micron for high purity
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY.
MLP $
S1-2600
S1-2601
V.P. OIL
V.P. OIL
1 QT.
1 GAL.
12
6
16.46
41.54
Vacuum Pump Oil
NU-CALGON VACUUM PUMP OIL
Nu-Calgon Vacuum Pump Oil is a quality, high-grade lubricant that performs at the deepest vacuum. It has a
very low vapor pressureand it has excellent lubricity for complete surface protection. It contains no additives or
detergents. In addition, its broad package line guarantees the right package size for all levels of service activity
from performing an occasional evacuation to conducting several every day.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-438307
S1-438324
S1-438334
VACUUM PUMP OIL
VACUUM PUMP OIL
VACUUM PUMP OIL
1 GAL.
1 QT.
1 PT.
69.25
25.25
16.00
CPS Products Vacuum Pump Oil
PRO-SET® Premium Vacuum Pump Oil is an extremely high quality, severely hydrotreated vacuum pump oil. The oil is compatible for
use in pumps made by most manufacturers. PRO-SET® Premium Vacuum Pump Oil should always be clean and free of
contaminants such as moisture, acids, vapors, dirt etc. It is strongly recommended that the vacuum pump oil be changed after each
use to improve service and the life of the pump.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CP-VPOG6
S1-CP-VPOQ12
OIL,VACUUM PUMP,GALLON BOTTLE,6 PK
OIL,VACUUM PUMP,QUART BOTTLE,12 PK
435.25
246.43
JB Vacuum Pump Oil
SOURCE 1 PART NO.
DESCRIPTION
CARTON QTY.
SIZE
WEIGHT
MLP $
S1-DVO-1
S1-DVO-12
S1-DVO-24
PINT BOTTLE
QUART BOTTLE
GALLON BOTTLE
24
12
6
8-1/2” X 14-1/2”L X 10”W
9-3/4”H X 13”L X 9-3/4”W
13”H X 16”L X 13”W
25 LBS.
25 LBS.
50 LBS.
14.79
21.54
66.04
* Item s are priced per each but must be ordered i n carton quantities.
329
Lubricant Products
NU-CALGON BREAK-N LUBE PENETRATING LUBRICANT
®
This advanced technology 4-in-1 product is made with Cerflon for high performance in a non drying penetrating lubricant. It’s highly
versatile with the ability to penetrate, lubricate, displace moisture, and provide superior resistance to corrosion. It’s especially
formulated to help free frozen parts and assemblies.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-412803
BREAK-N-LUBE
12 OZ. AEROSOL
17.39
®
NU-CALGON PHASE III REFRIGERATION OIL
Acid Test Kit
Formulated for use on POEs as well as mineral oils and alkylbenzenes. An inexpensive, disposable test kit that provides proofpositive that acid level in refrigeration lil is safe or unsafe. Phase separation makes it easy to see change in color of acid indicator
(even if a leak detection dye has been added to the oil). Just two bottles to work with. No glass to break open. Simple, safe, accurate
and small enough so you can carry several in your tool box.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-4320W8
PHASE III REFRIGERATION OIL ACID TEST KIT
30.96
Lubricants
DIVERSITECH HEAVY DUTY SILICONE LUBRICANT
Dry film lubricant. Water based and ideal for surfaces where petroleum based products are unsuitable. Contains no chlorinated
solvents and is safe on metal, plastic, rubber, vinyl, leather and wood. Non-stain, anti-static, and approved by USDA for use in
federally inspected meat and poultry plants. Approved for use in areas with incidental food contact.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-CRC-6
HEAVY DUTY SILICONE LUBRICANT – 13 OZ.
12
26.79
* M LP per each / sold by the case
DIVERSITECH INDUSTRIAL STRENGTH LUBRICANT
Leaves light oily coating. Quick release for seized mechanisms. Reduces wear caused by friction corrosion. Contains no chlorinated
solvents. Safe on rubber, paint, plastic, fabrics.
• 11-oz. can
SOURCE 1 PART NO.
DESCRIPTION
SHIPPING MULTIPLE
S1-CRC-2
S1-CRC-2G
LUBRICANT AND CORROSION INHIBITOR
INDUSTRIAL STRENGTH LUBRICANT – 1 GALLON
12
STD. PACK
MLP $
1
30.75
125.93
DIVERSITECH LST PENETRANT
Specially formulated with low surface tension for fast penetrating action. Displaces moisture. Powerful foaming action provides
complete surface coverage. Flash point of 175°F.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-CRC-8
LST PENETRANT – 11 OZ.
12
20.86
DIVERSITECH PENETRATING SOLVENT
• Knock'er Loose® Penetrating Solvent, 13-OZ. CAN
SOURCE 1 PART NO.
DESCRIPTION
SHIPPING MULTIPLE
MLP $
S1-CRC-1KB
PENETRATING SOLVENT - 12-OZ CAN
12
27.11
330
Lubricants
DIVERSITECH THERMAPLEX BEARING GREASE
Specifically developed to outperform conventional bearing greases and extend relubrication periods, reducing maintenance
requirements and grease use. Blue colored paste with excellent load carrying properties. T emperature range -22°F to 350°F.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-CRC-13
THERMAPLEX BEARING GREASE – 14.1 OZ.
30
16.64
DIVERSITECH ULTRA-LITE 3-36® NON-STAINING LUBRICANT
• 11-oz. can
SOURCE 1 PART NO.
DESCRIPTION
SHIPPING MULTIPLE
MLP $
S1-CRC-1
NON-STAINING LUBRICANT - 11-OZ CAN
12
30.11
DIVERSITECH WHITE LITHIUM WITH TEFLON
Pure white lubricant with T eflon additives. Provides maximum lubrication. Rust and oxidation inhibitors protect metal. Heat and water
resistant. Rapidly forms into a pure white grease that won’t melt or wash away.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-CRC-9
WHITE LITHIUM LUBRICANT – 10 OZ.
12
25.68
HEAVY DUTY RUST INHIBITOR
Forms heavy waxy coating. Effective corrosion inhibition under severe conditions and corrosive environments indoors and outdoors
up to two years. Safe on rubber, paint, plastics, fabric. Excellent anti-seize compound. Superior chain lubricant.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-CRC-3
HEAVY DUTY RUST INHIBITOR – 11 OZ.
12
35.64
* Sol d by standard pack / M LP per each
NU-CALGON PENETROIL
Penetroil frees stuck fan blades, blower shafts, pulleys, rusted nuts and bolts – any frozen, rusted, or seized metal part! New low
surface tension formula penetrates into the smallest spaces and breaks and dissolves the bonds of rust and corrosion. Lubricates and
protects metals with a dielectric strength to 50,000 volts. For industrial and professional use only.
Specially formulated with new low surface tension technology to seep into the smallest cracks, crevices, seams, or threads of rusted,
seized, and corroded parts. Quickly dissolves the bonds of rust, corrosion, carbon deposits, gums, varnishes, and grease to free the
metal parts. Penetroil displaces water and leaves a lubricating film to protect metal parts and further prevent rust and corrosion. Super
penetrating formula creeps into spaces as small as one millionth of an inch!
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-NC-61105
S1-NC-61106
Penetroil - 12 oz. can
Penetroil - 17 oz. can
12
12
27.29
34.25
331
Lubricants
PULL-A-SPOUT OILER
All purpose oiler with a 14” telescoping spout. Zooms out for long shots, and in for short shots, even zooms around corners. Squeeze
bottle action. Perfect lubricant for general industrial use. Contains four ounces of finest quality carbon free, rust and oxidation inhibited
lubricating oil. Plastic container won’t short out around electrical connections. No leakage.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-CO-1
PULL-A-SPOUT OILER – 4 OZ.
12 (DISPLAY)
4.32
RUST BREAKER
Quickly loosens rusted bolts, screws, shafts, piping, and all types of “Frozen” connections and assemblies. The answer for rusty or
corroded fastenings on cars, trucks, trailers, tractors, farm machinery, appliances, washing machines, plumbing, water pumps, fishing
reels, power tools, gardening equipment, and hundreds of other mechanisms. Packaged in a handy telescoping spout applicator.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-CR-1
RUST BREAKER – 4 OZ.
12 (DISPLAY)
5.29
WD-40
Loosens rusted parts. Stops squeaks. Rem oves tar, grease and adhesives. Displaces m oisture. Protects metal. New Sm art Straw 8oz. can.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-741-001
S1-741-002
WD-40 – 8 OZ.
WD-40 – 11 OZ.
12
12
15.61
19.18
332
Oatey Cutting Oil
Dark Thread Cutting Oil
•
•
•
•
Formulated for high speed cutting machines
A special mixture of sulfonated and chlorinated oils provides high film strength
Keeps machines running cooler and extends the life of your dies
Anti-mist and non-staining formula is not affected by weather
SOURCE 1 PART NO.
DESCRIPTION
SIZE
STD. PACK
MLP $
S1-30204
S1-30205
DARK CUTTING OIL (SPEED THREADING) - 32 OZ
DARK CUTTING OIL (SPEED THREADING) - 1
GALLON
32 OZ
1 GAL
12
6
30.57
70.14
SILICONE CAULK
BOSS® 370 HVAC Silicone is a one-part acetoxy cure adhesive sealant that is suitable for general heating, ventilation and air
conditioning sealing and adhesive applications. T his product will adhere to clean metal, glass, many types of wood, silicone resins,
vulcanized silicone rubber, ceramics and plastic surfaces. A primer may be required for optimum adhesion to some substrates.
Uses:
• Sealing heating, ventilating or air conditioning duct work
• Seal cracks or gaps around windows, vents, ducts, fixtures and lights
• Seal leaks in gutters, downspouts, ducts and piping
• Seal electrical connections and boxes to waterproof
• Bond gasket s in heating and refrigeration units
BOSS
SOURCE 1 PART NO.
DESCRIPTION
PRODUCT
PART NO.
MLP $
S1-RTVCLR
S1-RTVGRY
S1-RTVWHT
CLEAR, 10.1 OZ
GRAY, 10.1 OZ
WHITE, 10.1 OZ
37000
37003
37001
02260CL10
02260AL10
02260WH10
8.64
8.64
8.64
* Sold by Case of 12/M LP per Each
HIGH TEMP RED SILICONE CAULK
BOSS® 376 Hi-Temp HVAC/R Silicone is a one-part, non- slumping paste that cures to a tough, rubbery solid at room temperature on
exposure to water vapor in the air. This silicone product was formulated to perform at temperatures ranging from -85°F to 500°F (65°C to 260°C). It can be used for numerous sealing and bonding applications.
Uses:
• Sealing and encapsulating heating elements in appliances
• Stove and furnace vent pipes
• Moving oven belts
• Industrial ovens
• Bag filters on smoke stacks
• Other critical bonding, sealing, potting, encapsulating and protective coating where parts must perform at high temps
BOSS
SOURCE 1 PART NO.
DESCRIPTION
PRODUCT
PART NO.
MLP $
S1-RTVRED
HIGH TEMP RED SILICONE CAULK, 10.1 OZ
37610
02737RD10
13.18
* Sol d by Case of 12/M LP per Each
333
BOSS 125 MULTI SEAL BUILDING CONSTRUCTION SEALANT
BOSS® 125 Multi-Seal Building/Construction Sealant is a multipurpose, one part sealant, formulated from a hybrid polymer. This
unique sealant is free from solvents, silicone, isocyanates and other hazardous raw materials. It cures on exposure to atmospheric
moisture to form a highly durable flexible sealant. Multi-Seal has been formulated to offer outstanding primerless adhesion to most
common building materials including vinyl, aluminum, steel, concrete, wood and glass. It can be applied and tooled under most
weather conditions. This sealant is paintable with most latex base paints.
Features:
• VOC Compliant in all 50 states
• Ease of use, one-part sealant, no mixing required
• Good weatherability - virtually unaffected by sunlight, rain, snow, ozone, and temperature extremes
• Good UV resistance and color stability
• Long life reliability; cured sealant stays flexible without tearing, cracking, drying out, or becoming brittle.
• With its non slump properties, can be used in vertical, horizontal and overhead joints
• Wide temperature gunnability; can be applied in any season
• Non-yellowing and non-staining
• Non-streaking
• Paintable with most latex base paints*
• Free from solvents and isocyanates
• Bonds to Kynar 500®
SOURCE 1 PART NO.
DESCRIPTION
BOSS PART NO.
MLP $
S1-BOSS12501
S1-BOSS12502
S1-BOSS12503
SEALANT, CONSTRUCTION, MULTI-PURPOSE, 10.1-OZ, WHITE
SEALANT, CONSTRUCTION, MULTI-PURPOSE, 10.1-OZ, BLACK
SEALANT, CONSTRUCTION, MULTI-PURPOSE, 10.1-OZ, GREY
03970WH10
03970BK10
03970GY10
13.50
13.50
13.50
BOSS 326 HI-TEMP RED SILICONE SEALANT
•
•
•
•
•
Provides a protective coating where parts must perform at temperatures up to 500F
Used in critical bonding, sealing, potting, and encapsulating applications
Paste grade acetoxy silicone
Cures to a tough rubbery solid at room temperature
Meets NSF Standard 51, and FDA/USDA requirements for use in establishments operating under Federal Meat and Poultry
Inspection Program
SOURCE 1 PART NO.
DESCRIPTION
COLOR
PACKAGE
CARTON QTY
MLP $
S1-BOSS32610
HI-TEMP SILICONE SEALANT
RED
10.1-OZ CARTRIDGE
12
19.86
BOSS 363 50 YEAR SEALANT ACRYLIC LATEX WITH SILICONE
•
•
•
•
•
•
•
•
50 year durability
Interior and exterior uses
Paintable
ASTM Specification C-834
Mildew Resistant
Tough flexible bond
Water resistant
Non-yellowing
SOURCE 1 PART NO.
DESCRIPTION
COLOR
PACKAGE
CARTON QTY
MLP $
S1-BOSS36300
S1-BOSS36301
S1-BOSS36303
50-YR LATEX SEALANT
50-YR LATEX SEALANT
50-YR LATEX SEALANT
CLEAR
WHITE
GREY
10.1-OZ CARTRIDGE
10.1-OZ CARTRIDGE
10.1-OZ CARTRIDGE
12
12
12
9.04
6.57
6.57
334
BOSS 368 BUTYL SEALANTS
BOSS® 368 Butyl Rubber Sealant is a one component skinning product for sealing standing seam roofs and side walls. BOSS® 368
provides excellent adhesion to metal, asphalt, wood, and masonry substrates.
Uses:
• Seals standing seam roofs
• Seals side walls
• Seals gutters and downspouts
• Filling and caulking joints in heating and air conditioning ducts
• Excellent sealant for sealing joints in sheet metal
• Compatible with and suitable for use on polyurethane foam and extruded polystyrene
Specifications:
BOSS® 368 meets or exceeds the following: TT-S-001657, TT-C- 1796A, Type I, Class A. BOSS® 368 meets FDA Regulation, food
additives, sub-part F, sub-paragraph 175.105 being composed of ingredients acceptable for packing and transporting food. BOSS®
368 is acceptable to the U.S. Department of Agriculture for use in meat and poultry processing areas under Federal Inspection.
BOSS® 368 meets ASTM-E-90 and ASTM-E-84.
SOURCE 1 PART NO.
DESCRIPTION
BOSS PART NO.
MLP $
S1-BOSS36802
BUTYL RUBBER SEALANT, BLACK, 10.1 OZ
02684BK10
11.04
BOSS 380 CONTRACTORS SILICONE SEALANT
•
•
•
•
Suitable for general construction applications
Provides weatherproof and waterproof seal
Resist s ozone, UV radiation and temperature extremes
Fills and seals gaps around windows, doors, vents, fixtures and lights
SOURCE 1 PART NO.
DESCRIPTION
COLOR
PACKAGE
CARTON QTY
MLP $
S1-BOSS38000
S1-BOSS38001
S1-BOSS38002
S1-BOSS38003
CONTRACTOR'S SILICONE SEALANT
CLEAR
WHITE
BLACK
GREY
10.1-OZ CARTRIDGE
10.1-OZ CARTRIDGE
10.1-OZ CARTRIDGE
10.1-OZ CARTRIDGE
12
12
12
12
8.29
8.29
8.29
8.29
CAULK GUN
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-7-100
S1-7-200
CAULK GUN – SUPER RATCHET TYPE
CAULK GUN – STANDARD DUTY
12
12
21.18
7.36
Furnace Cement
HIGH HEAT FURNACE CEMENT
•
•
•
•
Unique environmentally clean and friendly formula
Will not shrink, crack or crumble
Meets OSHA requirements
Contains no asbestos or crystalline silica
SOURCE 1 PART NO.
DESCRIPTION
SIZE
STD. PACK
MLP $
S1-35503
High Heat Furnace Cement
8 OZ
24
5.11
335
SEALING GUM
Features:
• Easily formed by hand to any shape
• Seals out dust and moisture from joints
• Will not dry out or crack
• Firmly adheres to nonporous surfaces
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
S1-H-2901
GUM CORD
S1-H-2902
GUM SLUG
8” BEAD x 25’
ROLL
2-LB. SLUG
CASE/ORDER
QTY.
12
MLP $
24
15.82
13.11
* Sol d by case/M LP per each
DIVERSITECH DIVERSIGUM SEALING COMPOUND
Non-hardening. For plugging openings through foundations or around refrigeration tube entry.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-6-202-1
S1-6-202-2
DIVERSIGUM SEALING COMPOUND – 1 IB. SLUG
DIVERSIGUM SEALING COMPOUND – 2 IB. SLUG
24
20
5.82
9.79
Insulation Products
NU-CALGON INSULATION SEALING CORD
Insulation Sealing Cord is a non-staining sealer formulated from the highest quality raw materials. It is waterresistant,dust-resistant
and white in color with excellent adhesion to most surfaces and excellent insulation value. It is available as a pre-shaped extrusion
with serrated release paper.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-421627
INSULATION SEALING CORD
3/8” X 25’
27.75
NU-CALGON INSULATION SEALING SLUGS
Sealing Slugs compound is formulated and manufactured for use in many sealing, insulating and general maintenance applications. It
has excellent adhesion capability and is non-staining, non-hardening and unaffected by wide variations in temperature—an excellent
thumbing grade. It is packaged in 2-lb. boxes; each box contains two 1-lb. bars.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-421692
INSULATION SEALING SLUGS
2 LB. BOX
24.07
NU-CALGON FOOD GRADE SILICONE
Food Grade Silicone sprays a perfect non-stick surface on ice machine surfaces, vending machines, coin slots, slicing machines,
dairy machinery and other food processing and packaging equipment. An excellent lubricant that prevents binding and sticking.
Contains ingredients F.D.A.-approved for food contact use.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-408403
FOOD GRADE SILICONE
10.75 OZ. AEROSOL
34.07
336
Insulation Products
NU-CALGON NU-FOAM
TM
EXPANDING SEALANT
Nu-Foam is an expanding polyurethane prepolymer foam that is used as a sealant and an insulating product. It can be used to seal
and insulate areas such as openings created for refrigeration, air conditioning and heating tubes or pipes, duct joints, utility
penetrations in exterior sheeting, masonry, concrete or wood walls, and other areas where unwanted air penetration might occur.
Contains no CFCs nor HCFCs, and yields more insulation than similar competitive packages.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-429304
S1-429375
NU-FOAM EXPANDING SEALANT
NU-FOAM EXPANDING SEALANT
9 OZ.
20 OZ.
17.64
33.54
NU-CALGON PIPE-DRI® COLD PIPE INSULATION SPRAY
Aerosol insulation which provides a moisture barrier to stop sweating and dripping on refrigeration lines, air conditioning lines and
other cold surfaces. Quickly adheres and dries to a hard waterproof coating. Pipe-Dri makes it possible to insulate hard-to-reach
areas.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-429775
PIPE-DRI AEROSOL INSULATION
18 OZ. AEROSOL
28.36
BOSS 136 FIREBLOCK/DRAFTSTOP SEALANT
3
BOSS® 136 Fireblock/Draftstop Sealant is a single component fire rated sealant and is a noncombustible filler caulking used for
fireblocking applications in the annular space around wires, pipes, ducts, vents, cable lines and other penetrations to the building
envelope. It is a non-slumping sealant that sets to form a hard surface. BOSS® 136 can be applied to any gap or penetration where
the specification is noncombustible and/or ASTM-E136 rated. BOSS® 136 is to be used for interior applications only. The
noncombustible specification is common to one and two family construction and to non-rated penetrations in multi family and
commercial construction. BOSS® 136 is colored red for ease of inspection. In the event of a fire BOSS® 136 will prevent the spread
of fire, smoke and toxic gases through penetration openings. BOSS® 136 has been tested and meets the American Society for
Testing Materials E-136. To pass this test a material must withstand 1,400 degrees Fahrenheit without exhibiting signs of flaming after
the first thirty seconds in the test apparatus. BOSS® 136 serves to form a “gasket or seal against air infiltration”
Features:
• Completely non toxic and contains no asbestos or PCBs.
• Noncombustible
• Applied with a conventional caulking gun
• Easily applied sealant with water clean up capabilities
• An accredited fire block/smoke seal caulk
• Single component system, no mixing necessary and no additions required
• Meets residential construction code approvals including I.R.C.
• For interior applications only
• Excellent adhesion to a wide variety of substrate material
SOURCE 1 PART NO.
DESCRIPTION
BOSS PART NO.
MLP $
S1-BOSS13605
FIRESTOP/DRAFT SEALANT, 10.1-OZ
03221PK10
13.18
BOSS 333 TRIPLE EXPANDING FOAM SEALANT
BOSS® 333 is a ready-to-use, multi-purpose, polyurethane foam that expands to three times its original volume on contact with air.
The expanding action fills holes, cracks and gaps more completely than standard caulks. BOSS® 333 has excellent insulating
properties and superb adhesion to virtually all building materials.
Uses:
• Air sealing
• Partition walls with ceilings
• Through penetrations around cables and pipes
• Seams between chimneys, roof protection, roof panels and wall panels
SOURCE 1 PART NO.
DESCRIPTION
BOSS PART NO.
MLP $
S1-BOSS33316
S1-BOSS33324
TRIPLE EXPANDING FOAM SEALANT, 16-OZ
TRIPLE EXPANDING FOAM SEALANT, 24-OZ
01551BR10
02455BR10
12.89
22.11
337
BOSS 812 DRAFT/SMOKE STOP FOAM
BOSS® 812 Draft/Smoke Stop Foam prevents the spread of smoke and toxic gasse s from
one compartment to another, thereby slowing down the spread of fire, due to lack of air to fuel
the flames. BOSS® 812 has excellent insulation and acoustic properties, and is also paintable
(after inspection). BOSS® 812 has been tested to ASTM E-84 and is classified as Class A. BOSS®
812 Draft/Smoke Stop Foam
Features:
• Will adhere to almost any substrate
• Can be used to seal around copper, PVC pipes conduits and
large spaces left after the installation of waste pipes, ducting,
etc.
• Prevents the spread of smoke and toxic gasses
• Installed in seconds, reducing labor cost by up to 90%
• Ideal for single and two family homes
• Paintable (after inspection)
• Can be used on vertical or horizontal applications
• Excellent acoustic and thermal insulation
• Unaffected by moisture or humidity after curing
• CFC Free
• Very cost effective
• Reduces energy costs
• Prevents intrusion of insects and pests
SOURCE 1 PART NO.
DESCRIPTION
BOSS PART NO.
MLP $
S1-BOSS81212
FIRESTOP/DRAFT SEALANT, 10.1-OZ
81212
19.68
BOSS 816 INTUMESCENT FIRESTOP SEALANT
BOSS® 816 UL Classified Intumescent Firestop Sealant is a fire rated, general purpose sealant for use on through-penetrations and
construction joints. It is a single component, non-sag, water based sealant and smoke seal that is easy to apply and clean up. BOSS®
816 will prevent the spread of toxic gases, water, smoke and fire through joint openings and through penetrations. BOSS® 816 is
suitable for adhesion to almost any surface and remains flexible, making it ideal for both horizontal and vertical joints, subject to
vibration or dynamic movement. It bonds quickly, has excellent adhesion and is non-toxic. BOSS® 816 is protected against mold
growth with a combination of biocides in both wet and dry stages. It has been tested to the following specifications: UL 1479 (ASTM E814), UL 2079 (ASTM E-1966), ASTM E-84 (0-flame, 0-smoke), ASTM E-90 (STC 53), Factory Mutual Approved.
Features:
• Bonds quickly with excellent adhesion
• Excellent freeze/thaw properties
• Mildew Resistant
• Safe to use and handle
• Remains flexible
• Water based and paintable
• VOC compliant
• 2 year shelf life
SOURCE 1 PART NO.
DESCRIPTION
BOSS PART NO.
MLP $
S1-BOSS81610
INTUMESCENT FIRESTOP SEALANT, 10.1-OZ
03642RD10
20.75
DIVERSITECH FIRESTOP PRODUCTS FOR CLASS A BUILDINGS
U.L. Classified. Code Approved. Seal penetrations of plumbing, refrigeration and AC lines, ducts, vents and electrical cable through
firerated floors, walls and ceilings. Easy-to-use, nonshrinking, non-toxic and permanently flexible. Blocks fire, gas, smoke, air and
water migration. Use ceramic fiber filler together with putty or caulk for thick penetrations. Technical bulletins available.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-16491
FIRESTOP CAULK – RED – 10.3 FL. OZ. CARTRIDGE
10
51.71
338
DIVERSITECH FOAM SEALANT - ONE COMPONENT
One component closed-cell expanding polyurethane foam sealant for lineal caulking applications. Air moisture cure. T ack free in 20
minutes; fully cured in 12 hours. Paintable. Use for insulating and sealing around windows, doors, pipes, ducts and vents. Non-toxic
when cured. Paint to protect from UV exposure. “R” value 4.7 (1” thickness). Foam contains fire retarding chemical and is U.L. Listed
but not rated as a firestop product. Environmental concerns have led us to replace CFC’s and HCFC’s with hydrocarbon material in
our one component foam products. See instructions on each product to ensure safe use and quality results.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-01714
S1-01724
S1-10600
FOAM SEALANT – 12 OZ. CAN – YIELDS 275’ (3/8” BEAD)
FOAM SEALANT – 20 OZ. CAN – YIELDS 460’ (3/8” BEAD)
FOAM – 2 KIT – 600 BD. FT. KIT – YIELDS 50 CU. FT.
12
12
1
10.07
28.64
2577.18
DIVERSITECH FOAM SEALANT - TWO COMPONENT
Two component closed-cell expanding polyurethane foam sealant for cavity filling, surface coating and insulation applications. Rapid
chemical cure (Component A and Component B). Tack free in 2 minutes, fully cured in 20 minutes. Use for insulation repairs in
refrigerated enclosures. Spray coat and insulate tanks, pipes, tubs and panels. Non-toxic when cured. Paint to protect from UV
exposure. “R” value 5 (1” thickness). Kits include dispensing nozzles, hose and flow control mechanism. Foam contains fire retarding
chemicals and is U.L. Listed but is not rated as a firestop product.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-10012
S1-10180
12
1
71.46
1102.71
339
DIVERSITECH SWEAT-FREE PIPE INSULATION SPRAY
Sweat-Free is an aerosol spray-on insulation specifically developed for cold water pipes, refrigeration and air conditioning lines. Stops
sweating and dripping problems. Dries to a clean, white, flexible and water-resistant coating. Adheres to galvanized, black iron, steel,
brass, copper and PVC piping.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-770-15
SWEAT-FREE PIPE INSULATION – 15 OZ. AEROSOL
12
21.29
DESIGN POLYMERICS ADHESIVES
DP 2590 Solvent Based Spray Adhesive
DP 2590 Solvent Based Spray Adhesive is a premium quality, solvent based, fast drying, non-flammable, pressure sensitive insulation
adhesive. DP 2590 is supplied in a convenient spray sy stem which is both portable and cost effective.
Recommended Uses:
•
•
•
•
Bonding fiberglass duct liner to galvanized steel, stainless steel, and aluminum HVAC duct
Bonding fiberglass insulation to the exterior of galvanized steel, stainless steel, and aluminum HVAC duct
Sealing and bonding laps in HVAC duct insulation
Adhering kraft backed foil and foil jacketing to urethane foam
Features and Benefits:
•
•
•
•
•
•
•
•
Non-Flammable After Application
Quick Drying
Pressure Sensitive
Easy Application
Exceptional Coverage
Strong Permanent Bond
Resistant to Oxidation and Moisture
Portable
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-DP-2590-12
S1-DP-2590-40
DP 2590 Solvent Based Spray Adhesive (No CA Sale) - 12 Lbs
DP 2590 Solvent Based Spray Adhesive (No CA Sale) - 40 Lbs
1
1
487.01
689.94
340
DP 2590-CA California Compliant Solvent Based Spray Adhesive
DP 2590-CA California Compliant Solvent Based Spray Adhesive is a premium quality, low VOC, solvent based, fast drying, pressure
sensitive insulation adhesive. DP 2590-CA is supplied in a convenient spray sy stem which is both portable and cost effective.
Recommended Uses:
•
•
•
•
Bonding fiberglass duct liner to galvanized steel, stainless steel, and aluminum HVAC duct
Adhering kraft backed foil and foil jacketing to urethane foam
•
•
•
•
•
•
•
•
California Compliant
Quick Drying
Pressure Sensitive
Easy Application
Strong Permanent Bond
Resistant to Oxidation and Moisture
Portable
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-DP-2590CA-12
S1-DP-2590CA-40
DP 2590-Ca California Compliant Solvent Based Spray Adhesive - 12 lbs
DP 2590-Ca California Compliant Solvent Based Spray Adhesive - 40 lbs
1
1
446.43
767.05
TM
HARDCAST SURE-GRIP
404
A solvent based, synthetic rubber duct sealant, Sure-Grip’s exceptional strength, fast drying time, and unmatched flexibility make it
ideal for those applications requiring a solvent based sealant.
Features:
• Fast drying, no-drip, no-string formulation
• Indoor only
• Water, mold & mildew resistant
Specifications:
Color: Gray
Consistency: Heavy Brush on
Base: Synthetic rubber resin
Solv ent: Toluene & Heptane
Weight per gallon: 8.8 lbs.
Solids Content: 60%
Viscosity: 150K–200K cps
Coverage (per gal.): Up to 320 lin. ft. at 3” width, 20 mil thickness
Shore A Hardness: >60
Flexibility: Excellent
Time to Test: 24 hours
Service Temperature: –20°F to 200°F
VOC: 395 g/l
Pressure Classes: SMACNA 1/2, 1, 2, 3, 4, 6 and 10 inches w.g.
Seal Classes: SMACNA A, B, C
Packaging: 1/12 gal. cartridges, 1 and 5 gal. pails
Freeze/Thaw Stability: Passed 5 cycles
Specifications Compliance: Passes ASTM D-2202
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-302009
SURE-GRIP 404-4
57.61
341
Solvent Based Insulation Adhesive
HARDCAST GLAS-GRIPTM 658
A fast setting, pressure sensitive insulation adhesive. The self-contained spray system delivers a special low pressure web spray that
eliminates adhesive vaporization and spray bounce-back. Limited equipment clean-up and low equipment cost. Solvent based, yet
has limited flammability. This results in a more efficient spray system that works faster with no equipment down time for lower
operational costs.
Features:
• Immediate tack, strong bond
• Portable, self-contained system & spray cans
• Water and mildew resistant
Specifications:
Color: Green
Consistency: Aerosol spray
Spray Pattern: Variable web
Odor: Solvent-like
Base: Polymer
Vapor Pressure: 350 mm
Solv ent: Methylene Chloride
Coverage: Approx. 80 sq. ft. per 1 lb. of adhesive. 16 oz. spray can=80 sq. ft., 12 lb. cylinder= 960 sq. ft., 40 lb. cylinder=3200 sq. ft.
Initial Bonding Time: 2 to 3 minutes
Dry Time: 10 minutes
Service Temperature: 35°F to 200°F
Surface Burning: Flame Spread 0, smoke developed 0 (When tested in accordance with ASTM E-84)
Flammability: Flammable when wet (flame projection test), Non-flammable when dry.
VOC: 266 g/l
Packaging: 16 oz. spray cans, 12 lb., 40 lb., 187 lb. and 375 lb. aerosol cylinders
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-304293
GLAS-GRIP 658, 12# CYLINDER
243.46
HARDCAST INSTA-TACK INSULATION ADHESIVE
INSTA-TACK is an instant-tack, solvent-based insulation adhesive engineered for spray booth applications in high-humidity
environments. INST A-TACK is used when the duct section is stored vertically or horizontally before pinning. INSTA-TACK’s
exceptional coverage and fast tack provides reduced labor and lower application cost.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-308591
S1-308592
INSTA-TACK-RED-4-1 GAL
INSTA-TACK, RED, 5-GAL
43.11
160.68
DIVERSITECH SURE-STICK HEAVY DUTY ADHESIVE SPRAY
This wide web spray adhesive is ideal for both temporary and permanent bonding. Waterproof, transparent and non staining. Use for
the toughest adhesive applications with leather, cardboard, most plastics, polyethylene sheeting and insulation in HVAC applications.
Cleans with mineral spirits. Not for use on vinyl.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-315-20
SURE-STICK ADHESIVE SPRAY – 12 OZ. AEROSOL
12
12.82
NU-CALGON SPRAY ADHESIVE
Spray Adhesive is a fast-drying, all-purpose product that provides a strong, water-resistant, flexible bond. It is translucent and does
not penetrate or soak material causing bleed-through. Spray Adhesive is excellent for labeling, bonding, splicing and sealing paper,
cardboard, cloth, rubber, Styrofoam, canvas, leather, wood and most plastics.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-408004
SPRAY ADHESIVE
11 OZ. AEROSOL
36.96
342
NU-CALGON SPRAY-N-BOND® INSULATION & DUCT LINER ADHESIVE
A wide web spray adhesive formulated specifically for insulation and duct liner applications. It is ideal for porous surfaces. It is
waterproof, flexible, transparent and non-staining, and it can be used for both temporary or permanent bonds. Formulated with the
environment in mind, it contains no chloronated solvents or ozone depleters, and it is voc-compliant in states such as California.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-436975
SPRAY-N-BOND
13-OZ. AEROSOL
14.39
DP 2502 Water Based Duct Liner Adhesive
DP 2502 Water Based Duct Liner Adhesive is a water based, premium quality, UL Classified duct liner adhesive specifically
formulated for spray, brush, and roller applications.
Recommended Uses:
•
•
•
•
Bonding fibrous duct wrap and duct liner insulation to galvanized duct work
Sealing cut edges of fiberglass insulation
Bonding kraft backed foil coverings to fiberglass and urethane flat stock or pipe insulation
Bonding multiple layers of fibrous insulation board
•
•
•
•
•
•
•
•
•
•
LEED Qualified
UL Classified
Excellent Wet Tack
Non-Flammable
Moisture Resistant
Low Odor
Non-Oxidizing
Meets FDA, USDA, and EPA Standards
Meets Requirements of NFPA 90A & 90B, ASTM E-84, UL 723, ASTM C-916 Type II
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-DP-2502B-09-01
S1-DP-2502B-09-05
S1-DP-2502W-01-01
S1-DP-2502W-01-05
DP 2502 Water Based Duct Liner Adhesive - Black - 1 Gal
DP 2502 Water Based Duct Liner Adhesive - Black - 5 Gal
DP 2502 Water Based Duct Liner Adhesive - White - 1 Gal
DP 2502 Water Based Duct Liner Adhesive - White - 5 Gal
4
1
4
1
38.56
148.13
38.56
148.13
343
DP 3050 Water Based Lagging Adhesive
DP 3050 Water Based Lagging Adhesive is a water based, premium quality, quick drying, low odor lagging adhesive and protective
coating for indoor use.
Recommended Uses:
•
•
•
•
May be used for bonding and coating jackets of canvas, glass cloth and other lagging fabrics over insulated surfaces, including
rectangular and round ductwork insulation
May be used as a lap adhesive for canvas, glass cloth and pipe insulation jackets
May be used as a protective coating over expanded polystyrene foam insulation to prevent dusting and protect from solvents
May be used to seal cut ends of fiberglass duct liner
•
•
•
•
•
•
•
•
•
•
•
•
LEED Qualified
Bright White, will not discolor
Excellent Workability
High Strength and Durability
Crack and Peel Resistant
Water Resistant
Excellent Dry Adhesion
Sag Resistant
Meets Mil-A-3316C, Class 1, Grade A
Meets USCG 164.012
Meets Requirements of NFPA 90A & 90B, UL 723, and ASTM E-84
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-DP-3050W-01-01
DP 3050 Water Based Lagging Adhesive - White - 1 Gal
4
39.57
DP 77 Industrial Spray Adhesive
DP 77 pressure sensitive adhesive is a clear, industrial strength, multi-purpose aerosol spray adhesive with quick tack and high shear
strength.
Recommended Uses:
•
•
•
•
May be used to bond galvanized metal, wood, fiberglass, foam rubber, paper, glass, cardboard, textiles, plastics, and laminate.
Adhering kraft backed foil and foil jacketing to urethane foam.
•
•
•
•
•
•
•
•
Pressure Sensitive
Quick Drying
Permanent Bond
Lace-Like Web Spray Pattern
High Temperature Resistance - Bonds Maintained Even After Exposure To Heat Up To 200° F.
Non-Misting
No CFC’s
VOC Compliant
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-DP-77
DP 77 Industrial Spray Adhesive - 12 Oz Can
12
12.18
344
Water Based Duct Sealants
TM
HARDCAST IRON-GRIP 601 , FLEX-GRIPTM 550
A versatile, all purpose duct sealant for use on all types of metal duct, glass fiber duct board, and flex duct, as well as duct fabric and
flexible tubing runouts. Distinguished by its ability to accommodate minor vibration and movement, Iron-Grip stays flexible to save callback labor.
Features:
• Indoor/Outdoor use
• Stays flexible
• Water, mold & mildew resistant
• Easy application
• Non-sag formulation
• Proven reliability
Specifications:
Color: Gray
Consistency: Heavy brush on
Base: Synthetic latex
Solv ent: Water
Weight per Gallon: 10.5 lbs. (± 0.2)
Solids content: 62% (± 2)
Viscosity: >300K cps
Coverage (per gal.): Up to 320 lin. ft. at 3” width, 20 mil thickness
Flexibility: Passes 1/4” mandrel bend
Time to Test: 48 hours (May vary according to temperature and humidity.)
VOC: 79 g/l (less water)
Packaging: 1/12 gal. caulking cartridges, 1 gal., 5 gal. pails
Specifications Compliance: Passes ASTM C-731, ASTM D-2202.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-304132
S1-304135
FLEX-GRIP 550-4
IRON-GRIP 601-4
52.71
65.71
HARDCAST VERSA-GRIPTM 181
A versatile, all purpose duct sealant for use on all types of metal duct, glass fiber duct board, and flex duct, as well as duct fabric and
flexible tubing runouts. Versa-Grip incorporates a built-in fiber reinforcement for exceptional strength, with UV inhibitors for outdoor
use. UL181A-M listed/UL 181B-M listed.
Features:
• Indoor/Outdoor use
• Fiber Reinforcement
• Mold & mildew resistant
• Non-sag formulation
Specifications:
Color: CCWI181-4W is white CCWI181-4G is gray
Consistency: Heavy textured
Base: Synthetic latex
Solv ent: Water
Coverage:
UL 181 A-M: Apply 18 mil, scrim and 18 mil over scrim.
UL 181 B-M: Approximately 214 to 320 lin. ft. per gal. at 30 to 35 mil wet film thickness at 3” width
Flexibility: Passes 1/4” mandrel bend
Time to Test: 48 hours (May vary according to temperature and humidity.)
VOC: 45 g/l (less water)
Packaging: 1, 2 & 5 gal. pails; 10.3 oz. cartridge.
Weight per Gallon: 11.6 lbs. (± 0.2)
Solids content: 70% (± 2)
Viscosity: Thixotropic
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-304138
S1-304144
S1-304148
VG-181-WHITE-4-1 GAL
CCWI181-4W
CCWI181-4G
44.39
40.82
40.82
345
Water Based Insulation Adhesive
TM
COIL-TACK
INSULATION ADHESIVE
Coil-Tack is a low-tack, nonflammable, water-based insulation adhesive engineered for spray or extruding coil line applications. The
low viscosity, low-suspended solid eliminates clogging within the adhesive delivery sy stem, ensuring consistent operation. Coil-Tack’s
exceptional coverage and easy cleanup means lower application cost.
• UL 723 Listed.
SOURCE 1 PART NO.
S1-308580
DESCRIPTION
COIL-TACK-WHITE-1-5 GAL
CODE
MLP $
U.L. 723
142.21
HARDCAST ROTO-TACK INSULATION ADHESIVE
ROT O-T ACK is a mid-tack, nonflammable, waterbased insulation adhesive engineered for mechanical roll coating systems that
rapidly apply adhesive to insulation prior to bonding to the sheet metal. ROT OT ACK offers exceptional versatility, low viscosity, low
su spended solids and easy cleanup, providing lower application cost.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-308574
ROTO-TACK,CLEAR,5-GAL
238.29
HARDCAST TRAVEL-TACK® ADHESIVE
TRAVEL-TACK is a self-contained, instant-tacking portable spray system engineered to deliver a low-pressure web spray that
eliminates adhesive vaporization and overspray. TRAVEL-TACK’s portability, limited equipment clean-up and low equipment cost
make this adhesive ideal for shop or field use.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-308602
S1-308605
TRAVEL-TACK ADHESIVE 40# CYLINDER
ADHESIVE,DUCTLINER,TRAVEL-TACK,40-LB
698.89
805.57
SEAL-TACKTM INSULATION ADHESIVE
SEAL-TACK is engineered to seal cut ends of fibrous glass duct liner or to coat foam insulation. It provides exceptional vapor barrier
characteristics for liquid chiller piping insulation applications. SEAL-TACK’s exceptional strength and weather resistance provide
application flexibility for both indoor and outdoor use.
SOURCE 1 PART NO.
S1-308609
DESCRIPTION
SEAL-TACK-WHITE-4-1 GAL
CODE
MLP $
ASTM E-84
40.25
SPEED-TACKTM INSULATION ADHESIVE
SPEED-TACK is a fast-tack, water-based insulation adhesive engineered for fast-tacking spray applications where a quick, strong
tack is needed. SPEED-TACK is used when the duct section is stored vertically before pinning. SPEED-TACK’s tack time rivals that of
solvent-based adhesives. It offers exceptional strength, low viscosity, great coverage and low suspended solids.
SOURCE 1 PART NO.
DESCRIPTION
CODE
MLP $
S1-308589
SPEED-TACK-CREAM-1-5 GAL
ASTM E-84
228.68
346
TM
HARDCAST DUCT-SEAL
321
DUCT-SEAL 321 is an all purpose industrial grade duct sealant for all types of metal duct, glass fiber duct board, and flex duct, as well as duct fabric and
flexible tubing runouts. It includes UV inhibitors for extended outdoor exposure and built-in fiber reinforcement for added strength. This non-toxic water based
product is solvent free and is suitable for residential use.
Specifications:
Gray
Color
Smooth creamy texture
Consistency
Synthetic latex
Base
Water
Solv ent
10.6 lbs.
Weight per Gallon
65%
Solids Content
Thixotropic
Viscosity
Up to 320 lin. ft. at 3” width 20 mil thickness
Coverage (per gal)
>20
Shore A Hardness
Passe s 1/4 inch mandrel bend
Flexibility
48 hours*
Time to Test
20°F to 200°F (-29°C to 34°C)
Service Temperature
Weather resistant
Weather Resistance
Mold & Mildew resistant
Mildew Resistance
57.2 g/l (less water)
VOC (less water)
SMACNA ½ , 1, 2, 3, 4, 6 and 10 inches w.g.
Pressure Classes
SMACNA A, B, C
Seal Classes
Passed 5 Cycles
Freeze/Thaw Stability
Specifications Compliance ASTM D-2202, ASTM C-731. USDA, EPA and FDA Approved. LEED compliant.
SCAQMD Rule 1168.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-304156
S1-304159
DS-321 GRAY, 1 GAL, 4/CASE
DS-321 GRAY, 11-OZ CARTR, 25/CASE
38.21
4.50
Solvent Based Duct Sealants
DESIGN POLYMERICS SEALANTS
DP 1090 Low Voc Solvent Based Duct Sealant
DP 1090 Low VOC Solvent Based Duct Sealant is a smooth, solvent based, premium quality, UL Classified, high pressure/high
velocity duct sealant for commercial and industrial supply and return air duct use.
Recommended Uses:
•
•
•
•
•
Sealing joints, seams, and duct wall penetrations in commercial and industrial
applications
Sealing supply and return rectangular, round, oval and metal flexible ducts
Up to 15 inches water column pressure
Proj ects requiring LEED certification.
•
•
•
•
•
•
•
•
•
•
•
•
LEED Qualified, Low VOC
UL Classified
California Compliant
Mold and Mildew Resistant
Excellent Adhesion
Indoor and Outdoor Usage
Minimal Shrinkage
Sag Resistant
Excellent Water and U.V. Resistance
Meets Requirements of NFPA 90A & 90B, ASTM E-84, and UL-723
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-DP-1090-04-01
DP 1090 Low Voc Solvent Based Duct Sealant - 1 Gal
4
63.92
347
DP 1010 Water Based Duct Sealant
DP 1010 Water Based Duct Sealant is a smooth, water based, premium quality, UL Listed, high pressure/high velocity duct sealant for
commercial and residential supply and return air duct use.
Recommended Uses:
•
•
•
Sealing joints, seams, and duct wall penetrations
Sealing connections on flexible duct
•
•
•
•
•
•
•
•
•
•
•
•
•
•
LEED Qualified
ZERO VOC (ASTM D6886 Test Method)
UL Listed
Minimal Shrinkage
Sag Resistant
Paintable with latex or epoxy paints after cured
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-DP-1010-02-01
DP 1010 Water Based Duct Sealant - 1 Gal
4
39.16
DP 1015 Water Based Duct Sealant is a smooth, water based, UL Listed, high velocity duct sealant for commercial and residential
supply and return air duct use.
Recommended Uses:
•
•
•
Sealing joints, seams, and duct wall penetrations on metal air duct
Sealing connections on flexible duct or fiberglass duct board
•
•
•
•
•
•
•
•
•
•
•
•
•
•
LEED Qualified
ZERO VOC’s
UL Listed
Minimal Shrinkage
Sag Resistant
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-DP-1015-02-01
DP 1015 Water Based Duct Sealant - 1 Gal
4
30.44
348
DP 1030 Water Based Duct Sealant is a fiber reinforced, water based, premium quality,
UL Listed 181A-M / B-M, high velocity duct sealant for commercial and residential supply and return air duct use.
Recommended Uses:
•
•
•
Sealing joints, seams, and duct wall penetrations on metal air duct
Sealing connections on flexible duct or fiberglass duct board
•
•
•
•
•
•
•
•
•
•
•
•
•
•
LEED Qualified
ZERO VOC’s
UL Listed
Minimal Shrinkage
Sag Resistant
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-DP-1030GR-02-01
S1-DP-1030GR-02-12
S1-DP-1030W-01-02
S1-DP-1030W-01-10
DP 1030 Water Based Duct Sealant - Gray - 1 Gal
DP 1030 Water Based Duct Sealant - Gray - 10.5 Oz Can
DP 1030 Water Based Duct Sealant - White - 2 Gal
DP 1030 Water Based Duct Sealant - White - 1 Gal
4
25
1
4
29.83
5.28
62.09
30.44
349
PVC CEMENT & PRIMER
All Purpose Cement: Heavy bodied clear cement for use on ABS, PVS, PVC, or CPVC pipe & fittings. Flows freely &
provides a thick layer of cement on the pipe. Exceeds ASTM D-2564, D-2846, D-2235, F-493. Application temperature: 40°F
to 100°F
All Purpose Purple Primer: removes dirt, grease & grime. Flows freely and evaporates quickly. Temperature application
40°F to 100°F. For use on PVC & CPVC pipe & fittings. Softens pipe surface to allow for a fast, secure & permanent solvent
weld.
Regular Clear Cement: for PVC pipe & fittings, up to 4" Sch. 40 & up to 2" for Sch.80 potable water pressure pipe, gas
conduit, drain waste & vent pipe. Apply at temperatures 40°F to 100°F.
Clear All Weather Cement: For PVC pipe, good in all types of weather.
All Purpose Cleaner: A clear fast acting cleaner for use on ABS, PVC, & CPVC pipe & fittings, all schedules & diameters.
Does not penetrate pipe surface. Apply at temperature 40°F to 100°F.
All Purpose Cement for ABS, PVC, CPVC
SOURCE 1 PART NO.
DESCRIPTION
CASE QTY.
MLP $
S1-30818
S1-30821
S1-30834
4 OZ. CAN
8 OZ. CAN
16 OZ. CAN
24
24
24
8.00
12.31
26.93
SOURCE 1 PART NO.
DESCRIPTION
CASE QTY.
MLP $
S1-30782
S1-30795
S1-30805
8 OZ. CAN
16 OZ. CAN
32 OZ. CAN
24
24
12
8.36
9.86
20.93
SOURCE 1 PART NO.
DESCRIPTION
CASE QTY.
MLP $
S1-31132
16 OZ. CAN
24
24.54
* M LP per Each / Sold by the case
All Purpose Cleaner
All Weather PVC Cement
CPVC Medium Orange Cement
SOURCE 1 PART NO.
DESCRIPTION
CASE QTY.
MLP $
S1-31129
8-OZ. CAN
24
15.43
Purple Primer with Dauber Top
SOURCE 1 PART NO.
DESCRIPTION
CASE QTY.
MLP $
S1-30756
S1-30780
S1-30783
S1-30796
8-OZ CAN
4 OZ. CAN
8 OZ. CAN
16-OZ CAN
24
24
24
9.36
4.54
8.96
12.93
Rain-R-Shine Blue PVC Cement
SOURCE 1 PART NO.
DESCRIPTION
CASE QTY.
MLP $
S1-30891
S1-30893
CEMENT,PVC,BLUE,8-OZ CAN (M24)
16-OZ. CAN
24
24
12.96
21.71
350
PVC CEMENT & PRIMER
Regular Cement For PVC Pipe and Fittings
SOURCE 1 PART NO.
DESCRIPTION
CASE QTY.
MLP $
S1-31012
S1-31013
S1-31014
S1-31015
4 OZ. CAN
8 OZ. CAN
16 OZ. CAN
32 OZ. CAN
24
24
24
12
6.46
9.64
14.36
23.18
DIVERSITECH FAST CURE EPOXY
S1-DEP056 contains 10 individuallywrapped, premeasured packages. Each unique sealed package contains the exact A/ B portion
required for most small jobs. Easy peel-open containers press into shape to form handy mix-and-dispense cup. Reclosable cylinder
contains: Ten 0.12 oz. mixer packs and mixing sticks. Epoxy is also available in 1 pound kits (S1 DEP8001 and S1- DEP8002).
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-DEP056
S1-DEP8001
S1-DEP8002
EPOXY MIXER CUPS
ALUMINUM EPOXY PUTTY – 1 LB. KIT
WHITE EPOXY PUTTY – 1 LB. KIT
10
24
24
46.29
29.86
29.86
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-DEP052
SUPER GLUE – 2 GRAM TUBE
12
5.11
SUPER GLUE
WAGNER ADHESIVE SEALANT
For refrigerant sealing. Eliminates fastener loosening, leakage, and corrosion. Cures between thread flanks to seal against leakage
and prevents thread corrosion. Offers sealing with maximum solvent resistance to the action of refrigerant (11, 12 and 22), amm onia
and sulfur dioxide. Withstands corrosive liquids used in metal finishings and process industries. Ideal sealant for refrigeration, A/C,
and process equipment using corrosive chemicals.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-CAS-2712
WAGNER ADHESIVE SEALANT – 0.34 FL. OZ.
10
20.00
351
BOSS 270 PIPE THREAD SEALANT
BOSS® 270 Pipe Thread Sealant is a high quality industrial grade thread sealing compound that is grit-free, slow drying, soft setting,
non-hardening compound. BOSS® 270 Pipe Thread Sealant ensures leak proof joints in both metal and plastic piping. Permits low
torque make-up and easy disassembly without harming threads or seals. BOSS® 270 Pipe Thread Sealant may be used for thread
connections on all metals, ABS, PVC, CPVC and nylon plastics.
Features:
• Nontoxic
• Nonhardening
• Lead free
• Self setting
• Grit free
• No odor
• No separation
• Easy brush top applicator
Specifications:
BOSS® 270 Pipe Thread Sealant may be used on piping systems carrying acids (dilute), air and gases (compressed, natural,
manufactured), ammonia, brine, caustic alkalis (dilute), corrosives, diesel fuel, freons, gasoline, jet fuel (JP4, 5 and 6), kerosene, oils,
propane, solvents (alphatic, petroleum), steam, sugar or water. BOSS® 270 Pipe Thread Sealant meets approvals of ANSI/NSF:
Std. 14, Std. 61 and IAPMO’s UPC.
SOURCE 1 PART NO.
DESCRIPTION
BOSS PART NO.
MLP $
S1-BOSS27008
PIPE THREAD SEALANT, 8-OZ
04004YW10
27.25
BOSS 270 PIPE THREAD SEALANT WITH PTFE
BOSS® 271 Pipe Thread Sealant with PTFE is a high quality industrial grade thread sealing compound that is grit-free, nonhardening
compound. BOSS® 271 Pipe Thread Sealant with PTFE ensures leak proof joints in both metal and plastic piping. Permits low torque
make-up and easy disassembly without harming threads or seals. BOSS® 271 Pipe Thread Sealant with PTFE may be used for
thread connections on all metals, ABS, PVC, CPVC, polypropylene, and nylon plastics.
Features:
• Nontoxic
• Nonhardening
• Nonseizing
• No odor
• No separation
• Easy to clean up
• Easy brush top applicator
Specifications:
BOSS® 271 Pipe Thread Sealant with PTFE may be used on piping systems carrying acids (dilute), air and gases (compressed,
natural, manufactured), ammonia, brine, caustic alkalis (dilute), corrosives, diesel fuel, freons, gasoline, jet fuel (JP4, 5 and 6),
kerosene, oils, petroleum solvents, propane, steam, sugar or water. BOSS® 271 Pipe Thread Sealant with PTFE meets approvals of
ANSI/NSF: Std. 14, Std. 61, IAPMO’s UPC and FGG/BM.
SOURCE 1 PART NO.
S1-BOSS27108
DESCRIPTION
BOSS PART NO.
MLP $
PIPE THREAD SEALANT W/PTFE, 8-OZ
04006WH10
28.86
®
PIPE JOINT COMPOUND WITH TEFLON
A white, non-hardening, non-separating T eflon paste seals all threaded connections against leakage for internal pressure. Withstands
10,000 PSI at -100 F to 600 F, and formulated for use on water steam, natural and LP gas, oil, caustics, or dilute acid lines. Can also
be used with PVC, CPVC, ABS, Cycolac, Polypropylene, iron, steel or copper threads. Do not use on oxygen, fluorine, or molten
metal lines. Package with a brush top applicator.
SOURCE 1 PART NO.
DESCRIPTION
QTY/CASE
MLP $
S1-31230
S1-31231
4 FL.OZ. PIPE JOINT COMPOUND WITH TEFLON WITH BRUSH
8 FL.OZ. PIPE JOINT COMPOUND WITH TEFLON WITH BRUSH
12
12
15.04
27.43
* Sold by the Case Onl y / MLP per Each
PIPE JOINT COMPOUND
A fast set non-hardening paste which lubricates and seals threaded joints. Nontoxic and m ay be used on water, natural gas, stem and
air lines. Perfect for applying gaskets to flanges. Packaged with a brush top applicator.
SOURCE 1 PART NO.
DESCRIPTION
QTY/CASE
MLP $
S1-31227
S1-31228
4 FL.OZ. PIPE JOINT COMPOUND WITH BRUSH
8 FL.OZ. PIPE JOINT COMPOUND WITH BRUSH
12
12
7.61
14.29
* Sold by the Case Onl y / MLP per each
352
DIVERSITECH THREAD SEALANT WITH TEFLON
General purpose sealant with the lubricity of Teflon for metal pipes. Won’t shred like T eflon Tape. Allows easy disassembly. Resists
common shop fluids. -60° to 400°F temperature resistance. Pressure resistance of 5000 PSI.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-7-80632
S1-7-80633
THREAD SEALANT – 1/4 PINT BRUSH CAN
THREAD SEALANT – 1 PINT BRUSH CAN
12
12
16.32
39.29
HARDCAST ALUMA-GRIP™
ALUMA-GRIP 701 is a HEAVY DUTY pressure sensitive, duct joint rolled sealant. ALUMA-GRIP 701 provides an aggressive water
resistant grip to most surfaces including sheet metal, duct board, flex duct, PVC coated duct, and duct wrap vapor barriers. ALUMAGRIP 701 is suitable for subgrade application on PVC coated duct.
Specifications:
Appearance
Backing
Thickness
Sealant Material
Peel Strength
Tensile Strength
Elongation
Flexibility
Excellent,
Bonding Time
Time to Test
Service Temperature
Surface Burning
Mill finish aluminum substrate with gray adhesive/sealant
Aluminum
30 mils
Modified Butyl
17 lbs. per linear inch
720 psi avg.
560% avg.
no cracking
Instant high tack, full bond 24 hours
Immediate
-20°F. to 200°F.
Flame Spread:
25
Smoke Developed: 50
(When tested in accordance with ASTM E-84)
Weather Resistance Passe s 2000 hours QUV
(When tested in accordance with ASTM G-53)
Mildew Resistance Mold and mildew resistant
VOC
0 g/l
SMACNA 1/2, 1, 2, 3, 4, 6 and 10 inches w.g.
Pressure Classes
Seal Classes
SMACNA A, B, C
Packaging
50 ft. rolls in 2, 3, 4, 6, 9, 12 inch widths. 200 sq. ft. per case (150 sq. ft. for 9 inch)
Specifications Compliance
LEED compliant SCAQMD Rule 1168
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-304079
AFT-701, 3" x 50', 16/CASE
45.21
353
HARDCAST FOIL-GRIP
TM
1402
Foil-Grip is a pressure sensitive duct joint and general purpose rolled sealant. Foil-Grip provides an instant water resistant grip to most
surfaces including sheet metal, duct board, flex duct, PVC coated duct, and duct wrap vapor barriers. Foil-Grip is suitable for
subgrade application on PVC coated duct.
Features:
• Seals on Contact
• Indoor/Outdoor Use
• Printed Foil Available
• Mold & mildew resistant
• Excellent for subgrade
Specifications:
Appearance: Mill finish aluminum substrate with gray adhesive/sealant
Backing: 2 mil aluminum
Adhesive/Sealant: 15 mil Gray Matter 100% solids elastomeric modified butyl
Peel Strength: 16 lbs. per linear inch (adhesive only)
Tensile Strength: 955 psi avg.
Elongation: 560% (adhesive only)
Flexibility: Excellent, no cracking
Bonding Time: Instant high tack, full bond 24 hours
Time to Test: Immediate
Weather Resistance: Passe s 2000 hours QUV (when tested in accordance with ASTM G-53)
VOC: 0 g/l
Pressure Classes: SMACNA 1/2, 1, 2, 3, 4 and 6 inches w.g.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-304093
S1-304099
S1-304100
AFG-1402, 2" x 100', 24/CASE
1402 PRINTED FOIL 2” (24/CASE)
1402 PRINTED FOIL 3” (16/CASE)
37.04
41.32
62.04
* Sol d by case / M LP per roll
INSULATING TAPES
Features:
• Effectively insulate hot or cold pipes
• Stop condensation and drip
• Firmly adhere to all nonporous surfaces and to itself for multiple wrap applications
• Molds easily around valves and fittings
• Will not shrink or dry out
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY.
MLP $
S1-H-2700
S1-H-2800
CORK TAPE
FOAM TAPE
1/8” x 2” x 30’ ROLL
1/8” x 2” x 30’ ROLL
12
12
24.64
16.61
* Sol d by case/M LP per each
Insulation Products
NU-CALGON CORK INSULATION TAPE
Cork Insulation Tape has been developed specifically for the air conditioning and refrigeration industry. Through detailed research and
extensive testing, this tape has been formulated and manufactured to meet specific Nu-Calgon specifications as an insulating material
for preventing sweating and condensation on refrigerant lines, cold pipes and other commercial refrigeration and air conditioning
sy stems. It also can serve as an excellent insulator on hot pipes, and can be used as gasketing material and as sound-deadening
material. It can also be used for wrapping valves, tees and fittings, and can be applied at temperatures as low as –30°F.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-4217W3
CORK INSULATION TAPE
2” X 1/8” X 30’
36.68
354
Insulation Products
NU-CALGON CORK-TITE
TM
INSULATION TAPE
Cork-Tite Insulation Tape is specifically designed for all types of climates. It insulates cold pipes for all kinds of air conditioners used in
cars, homes, freezers and refrigerators. Helps to stop condensation problems. Ideal for retarding heat gain in cold pipes and
preventing heat loss in hot pipes. It is also an effective sound dampening material, and can be used for gasketing purposes. Cork-Tite
sticks to all kinds of dry metals. It seals tightly without drying. It is flexible and does not shrink or melt within the service temperature of
-20°F (-29°C) to +200°F (+93°C).
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-421712
CORK-TITE INSULATION TAPE
2" X 1/8" X 30'
24.71
NU-CALGON FOAM INSULATION TAPE
This economically priced tape is formulated from quality thermal insulation material. It utilizes closed-cell construction and can be
used on cold water pipes, chilled water lines and refrigerant lines to prevent sweating and condensation. It can also be used on hot
water lines for better insulation against heat loss. Can be overlapped or edges can be butted.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-421912
FOAM INSULATION TAPE
2” X 1/8” X 30’
22.04
NU-CALGON PERMA-WRAPTM FOAM INSULATION TAPE
Perma-Wrap is formulated from the highest quality elastomeric thermal insulation material. It is manufactured in accordance with
selected specifications to meet the needs of today's air conditioning, refrigeration applications. Its closed cell construction seals out
air, retarding heat transfer and providing complete insulation. It can be used on cold water pipes, chilled water and refrigerant lines to
prevent sweating and condensation. Perma-Wrap can also be used on hot water lines for better insulation against heat loss. Keeps
cold lines cold and hot lines hot. Can be overlapped or edges can be butted.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-421812
S1-4218W3
PERMA-WRAP FOAM INSULATION TAPE, DISPENSER PACK
PERMA-WRAP FOAM INSULATION TAPE
2" X 1/8" X 30'
2” X 1/8” X 30’
33.64
33.64
355
NU-CALGON QUICK SEALTM REPAIR TAPES
A complete line of easy-to-use quality repair tapes for the air conditioning, refrigeration and heating industries! Utilizing
MicroSealant™ Technology, Quick Seal Repair Tapes will fuse between any two surfaces (except silicone), and will never harden,
crack, peel or fall off like other HVACR sealing products, and can be used on a multitude of applications.
Applications:
• Roofing Materials: EPDM, CSPE/Hypalon, TPO, CPE, aged PVCs, APP and SBS modified, asphalt, BUR, coal tar BUR, shingle,
tile, and all metals.
• Roofing Accessories: Skylights, all gutter sy stems, copings, and chimneys.
• Building Materials: Wood, glass, plastic, masonry, brick, stone, steel, OSB board, Gypsum board, Polystyrene, vinyl siding,
sheeting membranes, and more.
• Also: HVAC ductwork, drain pans & equipment, canvas, pond and pool liners, ABS, fiber glass, polyethylene holding tanks, RV
roofs and watercraft seams, and more.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-429910
S1-429911
S1-429920
S1-429921
S1-429922
S1-429923
S1-429924
PIPE REPAIR TAPE
PIPE REPAIR TAPE
DOUBLE SIDED PUTTY
ALUMI-TAPE
ROOF REPAIR TAPE, BLACK
ROOF REPAIR TAPE, WHITE
WEB TAPE
2” x 3’
4” x 12’
2" x 4'
3" x 25'
3" x 25'
3" x 25'
3" x 25'
81.11
245.00
15.50
87.96
90.71
90.71
76.43
CARTON TAPE DISPENSER
Heavy duty, boxed.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-540-DISP
2” CARTON TAPE DISPENSER
18.21
356
VENTURE TAPE CORP. DUCT & FOIL TAPE
COMPARE TO
SOURCE 1 PART NO.
DESCRIPTION
VENTURE
SHURTAPE
COVALENCE
SIZE
MLP $
S1-1500B2
S1-1500S2
CLOTH DUCT TAPE, BLACK
CLOTH DUCT TAPE, GRAY
1500
1500
PC-609
PC-609
243, 396
243, 396
2" x 60YD, 11MIL
2" x 60YD, 11MIL
19.21
19.21
S1-1502-2
S1-1502-3
S1-1507
S1-1520CW2
S1-1520CW25
S1-1520CW3
S1-1525CW2
S1-1525CW3
S1-1580-2
S1-1580-3
S1-1580P2
S1-1580P3
S1-1581A25
S1-1581A3
S1-1599B2
S1-1599B3
S1-1599S2
S1-1599S3
S1-3243
S1-3520CW2
S1-3520CW3
S1-CST2
S1-VF803-3
METALIZED CLOTH DUCT TAPE
METALIZED CLOTH DUCT TAPE
LINESET TAPE, BLACK
FOIL DUCT TAPE
FOIL DUCT TAPE
FOIL DUCT TAPE
FSK DUCT TAPE
FSK DUCT TAPE
ALUMINUM MASTIC TAPE
ALUMINUM MASTIC TAPE
TAPE,ALUM,MASTIC,2" x 100 FT,17MIL (M24)
TAPE,ALUM,MASTIC,3" x 100 FT,17MIL (M16)
FOIL DUCT TAPE
FOIL DUCT TAPE
FLEX DUCT TAPE, BLACK
FLEX DUCT TAPE, SILVER
FOIL FLUE SEALING TAPE
FOIL DUCT
FOIL DUCT
CARTON SEALING TAPE, CLEAR
ALUMINUM FLASHING TAPE
1502
1502
2" x 60 YD, 10 MIL
3" x 60 YD, 10 MIL
2" x 60YD, 3MIL
2" x 50YD, 2 MIL
2.5" x 50YD, 2 MIL
3" x 50YD, 2 MIL
2" x 50YD, 8 MIL
3" x 50YD, 8 MIL
2" x 100', 17 MIL
2" x 100', 17 MIL
2" x 100', 17 MIL
3" x 100', 17 MIL
2.5" x 60YD, 2.4 MIL
3" x 60YD, 2.4 MIL
2" x 120YD, 3 MIL
3" x 120YD, 3 MIL
2" x 120YD, 3 MIL
3" x 120YD, 3 MIL
3" x 60 YD
2" x 50YD, 8 MIL
3" x 50YD, 8 MIL
2" x 55YD, 2.3MIL
3" x 50', 7.5 MIL
27.00
37.39
17.86
20.00
25.25
35.11
20.25
33.14
49.68
74.93
53.57
85.71
36.82
42.25
26.46
39.36
27.79
39.68
48.36
22.11
33.14
4.50
67.00
1520
1520
1520
1525
1525
1580
1580
1580P
1580P
1581
1581
1599
1599
1599
1599
3243
3520CW
3520CW
AF-973
AF-973
AF-973
AF-982
AF-982
322, 337
322, 337
322, 337
338
338
AF-100 UL181A-P
AF-100 UL181A-P
DC-181
DC-181
DC-181
DC-181
324, 339
324, 339
555,556
555,556
555,556
555,556
VF803
SHEATHING TAPE
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY
MLP $
S1-1585CW-P2
TAPE,SHEATHING,POLYPROP
1 7/8" x 72 yards
24
23.21
Tapes
ECONOMY ELECTRICAL TAPE
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-6-3460
3/4” x 60’ ECONOMY ELECTRICAL TAPE
10
2.07
357
Tapes
GLASS CLOTH, MOISTURE SEALING, & ECONOMY ELECTRICAL TAPES
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-ET130C1
S1-ET22
S1-GC275
S1-GC277
1” x 30’ MOISTURE SEALING SPLICING TAPE BY 3M
3/4” x 66’ HIAWATHA ELECTRICAL TAPE BY 3M
1/2” x 66’ GLASS CLOTH ELECTRICAL TAPE BY 3M
3/4” x 66’ GLASS CLOTH ELECTRICAL TAPE BY 3M
24
10
10
10
58.82
8.46
32.18
47.89
SCOTCH 35 VINYL ELECTRICAL TAPE
T his 7 m il prem ium grade electrical vinyl tape stretches to conform to virtually any shape that requires color-coded insulation.
Abrasion and weather resistant. Measures 3/4” x 66’.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-ET35G
S1-ET35N
S1-ET35R
S1-ET35W
VINYL ELECTRICAL TAPE – GREEN
VINYL ELECTRICAL TAPE – ORANGE
VINYL ELECTRICAL TAPE – RED
VINYL ELECTRICAL TAPE – WHITE
10
10
10
10
15.32
15.32
15.32
15.32
SCOTCH 3M SUPER 33+ ELECTRICAL TAPE
Premium grade, 7 mil thick, all-weather vinyl insulating tape. Perform s continuously in a temperature ambient of up to 220°F and as
low as 0°F. Resealable plastic case. M ade in USA.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-ET33
SUPER 33+ ELECTRICAL TAPE – 3/4” x 66’
10
16.39
SCOTCH 3M SUPER 88 ELECTRICAL TAPE
Premium grade, 8.5 mil thick, all-weather vinyl insulating tape. Perform s continuously in a tem perature am bient of up to 220°F and as
low as 0°F. Excellent resistance to abrasion, moisture, acids and corrosion. Packaged in a resealable plastic case. Made in the USA.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-ET44
SUPER 88 ELECTRICAL TAPE – 3/4” x 66’
10
20.50
HVAC System Hygiene
NU-CALGON A/C SHINE
A/C Shine is specially formulated to clean and protect the painted metal surfaces of outdoor A/C condensing units. It sprays on and
wipes off quickly and easily without water. Use A/C Shine on every service call.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-NC-61118
A/C Shine
12
24.04
358
Paints & Primers
®
PLASTI-KOTE ALL PURPOSE ENAMEL
An all purpose premium quality alkyd enam el formulated with an exclusive resin system that out perform s ordinary enamels. Fights
rust and is non-fading. 15-49% m ore square foot coverage vs. other brands.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-799-031
S1-799-032
S1-799-035
ALL PURPOSE ENAMEL – GRAY PRIMER
ALL PURPOSE ENAMEL – GLOSS BLACK
ALL PURPOSE ENAMEL – GLOSS WHITE
6
6
6
12.71
12.68
12.04
* MLP per eac h / s old by the c as e
PLASTI-KOTE® GENERAL PURPOSE SPRAY PAINT
New, more com plete line of professional quality fast drying spray paints. Color code compressors or refrigerant recovery cylinders to
m atch standard refrigerant identifying colors. T ouch up equipment housings.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-799-001
S1-799-002
S1-799-003
S1-799-004
S1-799-005
S1-799-006
S1-799-008
S1-799-009
S1-799-010
S1-799-011
S1-799-012
S1-799-013
SPRAY PAINT – GLOSS BLACK
SPRAY PAINT – FLAT BLACK
SPRAY PAINT – GLOSS WHITE
SPRAY PAINT – FLAT WHITE
SPRAY PAINT – DARK MACHINERY GRAY
SPRAY PAINT – GRAY PRIMER
SPRAY PAINT – BRIGHT YELLOW
SPRAY PAINT – ASTRO BLUE
SPRAY PAINT – ORANGE
SPRAY PAINT – ALUMINUM (SILVER)
SPRAY PAINT – BRITE ZINC GALVANIZING SPRAY
SPRAY PAINT – BRIGHT RED
6
6
6
6
6
6
6
6
6
6
6
6
8.89
8.89
8.89
8.89
8.89
8.89
8.39
8.89
8.89
8.89
22.75
8.89
PLASTI-KOTE® HIGH TEMP SPRAY PAINT
An ultra high temperature coating formulated to resist tem peratures up to 1500°F. Great for use on boilers, furnaces, steam pipes,
chim ney collars, com pressors and engine m anifolds.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-799-040
S1-799-041
HIGH TEMP SPRAY PAINT – ALUMINUM
HIGH TEMP SPRAY PAINT – BLACK
6
6
21.43
21.43
®
PLASTI-KOTE SPRAY ANY WAY ENAMEL
Finally an aerosol paint that sprays in any direction without clogging. We guarantee it! Dries tack free in 10 to 20 minutes; fully dry in
just one hour. Excellent corrosion and solvent resistance. Resists heat up to 250°F.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-799-020
S1-799-021
S1-799-022
S1-799-023
S1-799-024
S1-799-025
S1-799-026
SPRAY ENAMEL – GLOSS BLACK
SPRAY ENAMEL – FLAT BLACK
SPRAY ENAMEL – GLOSS WHITE
SPRAY ENAMEL – MACHINERY DARK GRAY
SPRAY ENAMEL – MACHINERY LIGHT GRAY
SPRAY ENAMEL – ALUMINUM
SPRAY ENAMEL – OSHA RED
6
6
6
6
6
6
6
14.25
15.07
16.36
14.25
15.07
15.07
14.54
TOUCH UP PAINTS
SOURCE 1 PART NO.
COLOR
CAN SIZE
MLP $
S1-51301503000
S1-51301505000
S1-51301530000
S1-51301531000
S1-51302881700
S1-51302934000
TITANIUM (SILVER)
CHAMPAGNE (NON-METALLIC)
CHAMPAGNE 2
TITANIUM 2
DESERT SAND (TAN)
CHAMPAGNE (METALLIC)
16 OZ.
16 OZ.
16 OZ.
16 OZ.
16 OZ.
16 OZ.
56.59
31.55
37.46
37.46
31.30
40.11
359
Contact Cleaners
DIVERSITECH CONTACT CLEANER
• QD® Contact Cleaner, 11-oz. can
SOURCE 1 PART NO.
DESCRIPTION
SHIPPING MULTIPLE
MLP $
S1-CRC-4CF
CONTACT CLEANER - 11-OZ CAN
12
49.75
DIVERSITECH ELECTRO 140° CONTACT CLEANER
Ideal for electrical/electronic parts. Flash point above 140°F. No rinsing or residue. Contains no CFCs. Superior wetting and
penetrating action.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-CRC-4-140
ELECTRO 140° CONTACT CLEANER – 11 OZ.
12
33.21
DIVERSITECH NOFLASH NU PRECISION CONTACT CLEANER
New patent-pending non-flammable formula. Fast evaporating, quick penetrating, no residue formula. Safe on most surfaces.
Replaces HCFC 141b or other chlorinated solvents. No flash point.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-CRC-4NU
NOFLASH NU CONTACT CLEANER – 15 OZ.
12
78.71
DIVERSITECH NOSPARK ELECTRICAL CLEANER
New patent-pending non-flammable formula. Fast evaporating, quick penetrating, no residue formula that is safe on most surfaces,
including plastics. Non-conductive. Replaces HCFC 141n or other HCFC cleaners.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-CRC-4NS
NOSPARK ELECTRICAL CLEANER – 14 OZ.
12
108.93
DIVERSITECH CBC II CONTACT CLEANER
A plastic safe, non-flammable electronic contact and circuit board cleaner. Dries fast, leaves no residue. No harsh fumes or odors.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-362-16
CBC II CONTACT CLEANER – 10 OZ. AEROSOL
12
37.00
NU-CALGON ELECTRICAL CONTACT CLEANER
Electrical Contact Cleaner cleans, lubricates and protects electrical contacts from corrosion, and is safe on most plastics. Cleaning
action quickly removes greases, dust and oxidation, restores and maintains precision and efficiency to the instrument and component.
Includes extension tube for pinpointing application.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-408203
S1-408204
ELECTRICAL CONTACT CLEANER
ELECTRICAL CONTACT CLEANER (LOW-VOC)
16 OZ. AEROSOL
16 OZ. AEROSOL
44.82
72.50
360
Degreasing Solvents
DIVERSITECH CRC® HEAVY DUTY DEGREASER
SOURCE 1 PART NO.
DESCRIPTION
SHIPPING MULTIPLE
MLP $
S1-CRC-7X
HEAVY DUTY DEGREASER - 19-OZ CAN
12
33.21
DIVERSITECH CRC® HEAVY DUTY DEGREASER II
SOURCE 1 PART NO.
DESCRIPTION
SHIPPING MULTIPLE
MLP $
S1-CRC-7-140
HEAVY DUTY DEGREASER - 15-OZ CAN
12
42.54
DIVERSITECH PRESOLVE
Quickly removes oil, grease, and dirt. Natural based solvent. Moderate evaporation. Does not contain CFCs. Does not require rinsing
or wiping. Flashpoint 104°. Not conductive.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-CRC-7PS
PRESOLVE – 15 OZ.
12
37.75
DIVERSITECH ZEROTRI
Quickly removes oil, grease, and dirt. Evaporates completely and very rapidly. Does not contain CFCs. Does not require rinsing or
wiping. Flashpoint is 0°F. Not conductive.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-CRC-7Z
ZEROTRI – 15 OZ.
12
49.18
NU-CALGON GREZ-OFF
Grez-Off is a powerful, biodegradable degreaser that quickly blasts through heavy grease and grime. Grez-Off works hard so you
don’t have to. It removes heavy grease and soil from engines, mowers, tools, bicycles, garden, farm equipment, condenser coils, shop
machinery, garage floors, asphalt drives, and much more. It's biodegradable, non-flammable formula hits hard and fast with less
impact on user and environment.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-NC-61116
S1-NC-61117
Grez-Off - 1 gallon
Grez-Off - 32 oz. spray bottle
4
12
50.39
18.75
361
Degreasing Solvents
NU-CALGON SPRAY NINE
Cleaning: Spray Nine digs out tough grease, grime, and other stubborn soils with “spray on, wipe off” ease from stainless steel,
plastic, glazed tile, rubber, vinyl, fiberglass sinks, glazed porcelain, formica, and other hard surfaces.
Sanitizing Non-Food Contact Surfaces: When used as directed, Spray Nine will sanitize hard, non-porous surfaces such as tables,
walls and floors. Spray Nine kills 99% of Staphylococcus Aureus and Klebsiella Pneumoniae in just 10 seconds.
Disinfecting:When used as directed, Spray Nine will disinfect hard, non-porous surfaces such as countertops, stainless steel, tables,
walls, and floors.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-NC-61110
S1-NC-61113
S1-NC-61114
Spray Nine - 1 gallon
Spray Nine - 32 oz. spray bottle
Spray Nine - 5 gallon
4
12
1
46.89
18.36
225.75
NU-CALGON AEROSOL DEGREASING SOLVENT EF
Degreasing Solvent EF is an “environmentally friendly” degreasing solvent, specially formulated for cleaning and degreasing
equipment where washing or flushing is not possible. Simply spray it on and wipe it off. Penetrates quickly and deeply, loosening and
liquefying heavy greases and tar. It is noncorrosive, non-staining and has a dielectric strength over 26,000 volts.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-408375
S1-408383
DEGREASING SOLVENT EF
DEGREASING SOLVENT EF (LOW VOC)
17 OZ. AEROSOL
17 OZ. AEROSOL
25.57
25.57
NU-CALGON DEGREASING SOLVENT EF
A new degreasing solvent, one that is “environmentally friendly” in that it is ozone-safe. It is a volatile solvent that provides effective
degreasing and cleaning as well as controlled drying with absolutely no residue. It has a dielectric strength in excess of 26,000 volts.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-416207
S1-416217
DEGREASING SOLVENT EF
DEGREASING SOLVENT EF (LOW VOC)
1 GAL.
1 GAL.
82.25
112.43
Galvanizing Compound Sprays
DIVERSITECH BRIGHTCOAT COLD GALVANIZE
Prevents rust and corrosion on all metals. Produces a shiny zinc coating that dries to the touch in 15 to 30 minutes. Heat resistant.
Will not yellow, chalk, crack or peel. Meets AST M A780-93A.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-CRC-5BC
BRIGHTCOAT COLD GALVANIZE – 13 OZ.
12
40.04
DIVERSITECH COLD GALVANIZING SPRAY
• Zinc-It® Zinc Rich Cold Galvanizing Spray, 13-oz. can
SOURCE 1 PART NO.
DESCRIPTION
SHIPPING MULTIPLE
MLP $
S1-CRC-5
COLD GALVANIZING SPRAY - 13-OZ CAN
12
46.89
362
NU-CALGON ZINC RICH COLD GALVANIZING COMPOUND
Perfect for Corrosion Repair
Zinc Rich Cold Galvanizing Compound is highly resistant to nearly all forms of corrosion. Perfect for repairing factory galvanized
material damaged in shipment, welding, assembly, etc. Its 95% pure zinc film fuses itself to iron, steel or aluminum. Blends well with
hot-dip coating.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-408703
ZINC RICH COLD GALVANIZING COMPOUND
16 OZ. AEROSOL
34.68
363
Hand Cleaners
FAST ORANGE HAND CLEANER
Hand Cleaner
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-HCO-7
S1-HCP-15
S1-HCP-7
CLEANER,HAND,FAST ORANGE,7.5-OZ
CLEANER,HAND,FAST ORN W/PMC,15-OZ
CLEANER,HAND,FAST ORN W/PMC,7.5-OZ
12
12
12
7.36
9.79
7.36
Personal Hygiene
NU-CALGON CLENHANDS HAND CLEANERS
Nu-Calgon ClenHands Orange Smoothie and Orange Crush
ClenHands Orange Smoothie and Orange Crush are premium citrus-based hand cleaners that quickly dissolve all hard-to-remove
soils. ClenHands Orange Smoothie is a smooth non-pumice formula while ClenHands Orange Crush is enhanced with fine-ground
American pumice. Both citrus lotion hand cleaners are formulated with nine skin care ingredients including aloe, jojoba, glyceri n,
wheat germ extract, almond oil, soil oil and vitamins A,C, and E to help protect hands. ClenHands Cherry Crush is a cherry-scented
antimicrobial hand cleaner with pumice. It quickly dissolves hard-to-remove soils and is formulated with ten skin care ingredients
including all of the above plus lanolin. ClenHands Super Gel is a traditional petroleum-based gel hand cleaner. It emulsifies dirt,
greases, inks, tar, asphalt, oils, lubricants, paints, industrial carbon and other heavy-duty soils. It is formulated with 5 skin care
ingredients including aloe, jojoba, glycerin, wheat germ extract,and vitamin E.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-NC-61201
S1-NC-61202
S1-NC-61203
S1-NC-61204
S1-NC-61205
Orange Crush with Pumice 1 gal.
Orange Smoothie Non Pumice 15 oz.
Orange Crush with Pumice 15 oz.
Cherry Crush with Pumice 15 oz.
ClenHands Super Gel 11 oz.
4
12
12
12
12
51.93
9.61
9.71
11.54
8.11
NU-CALGON GREAT WIPES INDUSTRIAL STRENGTH HAND TOWELS
Great Wipes Industrial Strength Hand T owels are waterless wipes made specifically for the air conditioning, refrigeration, and
plumbing service technician. Each premoistened, heavy duty towel has strong pumice scrubbing power that conveniently cleans
anywhere and anytime.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-418575
INDUSTRIAL HAND WIPES, 75-COUNT BUCKET
34.57
®
NU-CALGON SCRUBS -IN-A-BUCKET
A revolutionary pumice hand-cleaner impregnated towel. It is disposable and is available in self-dispensing canisters. Cleans hands
anywhere, anyplace, anytime!
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-436624
S1-436687
SCRUBS-IN-A-BUCKET
SCRUBS-IN-A-BUCKET
30-COUNT CANISTER
72-COUNT CANISTER
27.96
56.86
364
NU-CALGON THERMO-TRAP®
A heat absorbing paste designed to isolate heat encountered in soldering, welding and brazing, thereby preventing damage to nearby
heat sensitive controls, fittings or other materials.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-437132
S1-437136
S1-437153
THERMO-TRAP GEL,32-OZ SPRAY BOTTLE (M6)
THERMO-TRAP
THERMO-TRAP GEL,4-OZ (M12)
32-OZ. SPRAY BOTTLE
11 OZ. TUBE
4-OZ.
40.82
26.54
20.07
NU-CALGON FREEZ-KONTR'L®
A complete heat transfer fluid and anti-freeze based upon non-toxic propylene glycol. It is formulated to provide corrosion protection
and freeze protection for chilled water, hydronic and other closed systems. Safe to use where contact with potable water is possible.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-418802
S1-418805
S1-418807
FREEZ-KONTR'L
FREEZ-KONTR’L
FREEZ-KONTR’L
55 GAL. (PLASTIC)
5 GAL.
1 GAL.
2187.64
208.71
43.25
NU-CALGON FREEZ-THERM®
A complete, inhibited heat transfer fluid and anti-freeze based upon ethylene glycol. It can be used in chilled water, hydronic and other
closed systems for both freeze point suppression and corrosion inhibition. Formulated with a green/yellow dye for product
identification and leak detection. An uninhibited version is also available in drums on special order.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-418901
S1-418905
S1-418907
FREEZ-THERM
FREEZ-THERM
FREEZ-THERM
55 GAL.
5 GAL.
1 GAL.
2538.82
239.18
49.43
NU-CALGON GLYCOL REFRACTOMETER
A special refractometer for determining the concentration of ethylene glycol or propylene glycol in aqueous sy stems. Measures the
refractive index of the solution, and results are read as actual concentration of either glycol.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-48160
REFRACTOMETER, GLYCOL
911.29
NU-CALGON TY-ION B14A BOILER AND CLOSED SYSTEM WATER TREATMENT
Ty-Ion B14A is a one product boiler treatment that controls boiler scale and corrosion and condensate line corrosion in low pressure,
low make-up steam heating boilers where most of the condensate is returned. Ty-Ion B14A is chromate free and it contains a color
indicator for visual determination of treatment residual. Its balanced formulation provides an energy efficient operation of the heating
plant.
Features:
• Complete one product treatment for the prevention of sludge, oxygen putting, corrosion and condensate corrosion.
• No special mixing or tanks required; can be used straight from the drum.
• Built-in color indicator provides for easy on-going, visual determination of product treatment level in system, without chemical
testing.
• Easy to use calorimetric test is available if desired. Assures exact dosage for economical use.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-751905
TY-ION B14A BOILER TREATMENT
5 GAL.
519.57
365
NU-CALGON TY-ION® B20
A liquid nitrite-borax corrosion inhibitor and dispersant for closed recirculating systems. It combines corrosion inhibitors, a unique
copolymer dispersant, and a color indicator into a complete treatment for both hot and chilled water closed systems containing ferrous
and non-ferrous metal components. The color indicator facilitates leak detection and proper treatment residuals.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-753705
TY-ION B20
5 GAL.
407.82
NU-CALGON ALGAECIDES
No. 90 Algaecide is a chlorine bromine-donating organic compound in tablet form. This product, when dissolved in water, slowly
releases powerful oxidizing hypohalous acids which prevent algae and slime bacteria fouling in open recirculating cooling water
sy stems and evaporative coolers. No. 90 Algaecide also has the capability of breaking up and removing existing biological masse s
from system surfaces.
No. 85 Algaecide is a polymeric, catatonic biocide that has been developed for controlling the growth of algae, bacteria and fungi in
recirculating water systems, industrial washing systems and closed systems.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-410808
ALGAECIDE NO. 85
1 GAL.
306.00
NU-CALGON CAL-TREAT® 233
A liquid formulation that is fed with the S1-4669W3 or S1-4670W3 Drip Feeder or feed pump for controlling severe corrosion in
evaporative condensers and cooling tower systems. It is based upon a synergistic formulation of zincand molybdate as well as organic
phosphonate. Provides superior corrosion control and inhibits scale deposition.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-414905
CAL-TREAT 233
5 GAL.
578.75
NU-CALGON CMS FEED PUMP
This pump is a microprocessor controlled positive displacement diaphragm type pump. It is adjustable from 0.026 gallons feed per day
to a maximum of 15 gallons per day. Encoder switch allows for exact setting of pump strokes per minute. Also includes adjustment of
stro ke length.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-46091
CMS FEED PUMP
1472.57
NU-CALGON CMS-IV COOLING TOWER MONITOR SYSTEM
The newest innovation for monitoring conditions in cooling towers and evap condensers, and providing subsequent bleed-off and
chemical feed. The CMS-IV features a combination monitor and pump engineered into one piece of equipment. The Pump/Monitor
can feed up to 15.1 gallons of treatment per day, but can be adjusted to feed as low as 0.0021 gal. per day. The monitor’s frequency
can be adjusted from a maximum of 125 stroke s per minute to as low as 1 stroke per hour. Stroke length is also adjustable. The unit
can utilize any one of 5 feed-timer options, and the complete system does include a solenoid valve.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-46084
CMS-IV COOLING MONITOR FEED SYSTEM
3894.64
366
NU-CALGON ECO-LYME COOLING TOWER CLEANER/DESCALER
Eco-Lyme is a specially formulated new age descaler providing performance of traditional high strength descalers in removing scale
and corrosion deposits. It's the only product in the HVAC/R Industry that provides performance comparable to hydrochloric acid but
safer on metals, odorless, low-foaming, and is 100% biodegradable. Eco-Lyme will quickly and safely remove scale and/or corrosion
deposits from copper, steel, iron, aluminum, brass, wood, rubber and plastic equipment. Care must be exercised with galvanized
surfaces. Eco-Lyme is accompanied with pH strips to monitor product activity in the field. It is not formulated with a dye system.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-416701
S1-416705
S1-416708
COOLING TOWER CLEANER
55 GAL.
5 GAL.
1 GAL.
1801.63
182.48
39.21
NU-CALGON HUMIDI-TREAT SCALE INHIBITOR
Humidi-T reat is designed for humidifiers using up to 25 gallons per day, and will inhibit scale for one season. Install Humidi-T reat on
the water line that supplies water directly to the humidifier.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-419002
SCALE INHIBITOR
43.89
NU-CALGON MICRO-CARBON 4 WATER FILTER
The Micro-Carbon 4 utilizes a standard 12 x 40 mesh washed carbon rated at a nominal 20 micron filter capability. It is designed to
remove sediment and objectionable tastes and odors from water and ice making equipment. One unit can last up to 5-6 months, and
can handle flow rates up to 1.0 gpm. Each unit has a rated burst strength over 500 psi, and is available with 1/4" FPT connections or
John Guest fillings. It is NSF-listed to standard 42 for taste, odor and chlorine reduction, Class I.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-461724
MICRO-CARBON 4 FILTER
53.39
NU-CALGON NO. 340 LIQUID SCALE INHIBITOR
A unique inhibitor that is extremely effective in hard or highly alkaline water. No. 340 Liquid Scale Inhibitor is stable and does not form
any orthophosphate sludge. It is most effective at treatment levels between 10 and 15 parts per million (about 1 gallon of No. 340 per
100,000 gallons of water). A feed rate of 1/2 gallon per month is recommended for each 30 tons and 1 gallon per minute bleed-off. A
constant, accurate feed is accomplished with the No. 215 Drip Feeder on systems up to 60 tons. For larger systems, a No. 1075 Drip
Feeder or CMS Feed Pump should be used.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-434005
S1-434008
NO. 340 LIQUID SCALE INHIBITOR
NO. 340 LIQUID SCALE INHIBITOR
5 GAL.
1 GAL.
829.96
197.57
NU-CALGON TY-ION® C70
An all-organic liquid scale, deposit and corrosion inhibitor for use in open recirculating cooling water systems, evaporative condensers
and air washer systems. This treatment program is particularly effective in preventing scale deposits in systems which utilize make-up
water with high scaling potentials.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-759705
S1-7597P3
TY-ION C70
TY-ION C70
5 GAL.
15 GAL.
789.93
2016.86
367
SOURCE 1 ICE MACHINE CLEANER
Features:
• Removes slime and scale buildup and restores efficiency of ice machines
• Fast acting, non-foaming
• Nickel Safe—meets Manitowoc spec. GES-6 for ice machine cleaner
• All food-grade ingredients
SOURCE 1 PART NO.
DESCRIPTION
PACKAGE
CASE/ORDER QTY.
MLP $
S1-301
GREEN
1 GAL.
4
60.00
Everpure Products
NU-CALGON WATER FILTRATION PRODUCTS, EVERPURE AND NU-PLUS
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-462101
S1-462102
S1-462105
S1-462110
S1-462111
S1-462120
S1-462121
S1-462130
S1-462141
S1-462142
S1-462143
S1-462144
S1-462210
S1-462220
FILTER HEAD, SINGLE, QC71
FILTER HEAD, TWIN PARALLEL, QC71
FEEDER, SCALE INHIBITOR, SR-X
FILTER, ICE MACH, NU-I20002 (M6)
FILTER, ICE MACH, NU-I40002
FILTER, WATER, NU-MC2
FILTER, WATER, NU-XC2
FILTER, WATER, NU-7CB5S
PREFILTER, WATER, EC-110
CARTR, FILTER, WATER, NU-PLUS CU-S
CARTR, FILTER, WATER, NU-PLUS CU
442.79
785.50
446.93
179.45
199.75
158.11
193.93
178.39
9.04
177.46
18.96
295.86
123.61
112.57
Feeding Equipment
NU-CALGON DRIP FEEDERS NO. 215 & NO. 1075
The No. 215 Drip Feeder is used for feeding No. 340 Liquid Scale Inhibitor, Cal-Treat 233, Ty-Ion C70 and No. 85 Algaecide. Each
feeder is individually calibrated at the factory to insure accurate feeding. Provides the benefits of continuous treatment for small
sy stems without the high cost usually associated with automatic feeding equipment. The 1075 Drip Feeder is used for feeding the
same chemicals as the No. 215 Drip Feeder except that the flow rate is five times greater. Generally recommended for systems larger
than 60 tons.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-4669W3
S1-4670W3
DRIP FEEDER NO. 215
DRIP FEEDER NO. 1075
104.54
104.54
NU-CALGON MICROMET® FEEDER NO. 20L & FEEDER NO. 100L
Steel tanks suitable for pressure s up to 150 psi and temperatures up to 212°F. Uses 3/4-inch FNPT connections for installing on
bypass to any size line. Use No. 20L Feeder for initial charge up to 20 pounds. No. 100L Feeder for initial charges up to 100 pounds.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-46280
S1-46500
MICROMET FEEDER NO. 20L
MICROMET FEEDER NO. 100L
1012.18
2056.36
368
NU-CALGON ICE GUARD® SLIME CONTROL SYSTEM
Features:
• One unit can protect up to a 1200-lb. ice maker for up to 6 months.
• All components are NSF listed.
• Inhibits slime from waterborne bacteria.
• Enhances quality of ice.
• Reduces maintenance costs.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-420906
ICE GUARD SLIME CONTROL SYSTEM
165.89
NU-CALGON ICE MACHINE FILTRATION PRODUCTS
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-470187
S1-470287
S1-470424
S1-470587
S1-470687
S1-471187
S1-471287
S1-471424
S1-471587
S1-471687
S1-471787
CARTR, FILTER, ICE MACH, NP24C
CARTR, FILTER, ICE MACH, NP24S
HSG, FILTER, ICE MACH, NP24DD
CARTR, FILTER, ICE MACH, NP246R
CARTR, FILTER, ICE MACH, NP24PC (M6)
CARTR, FILTER, ICE MACH, NP48C
CARTR, FILTER, ICE MACH, NP48S
HSG, FILTER, ICE MACH, NP48DD
CARTR, FILTER, ICE MACH, NP486R
CARTR, FILTER, ICE MACH, NP48PC
CARTR, FILTER, ICE MACH, NP48PS
72.57
9.36
116.50
144.18
116.11
144.82
16.25
147.25
233.04
199.46
68.04
NU-CALGON IMS-II SANITIZING CONCENTRATE
IMS-II is an EPA-registered sanitizing concentrate formulated exclusively to sanitize hard, non-porous surfaces to eliminate odors and
slime growths. No rinsing is required. Formulated for general use in ice machines, ice cream dispensing equipment and other food
processing equipment.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-421134
IMS-II SANITIZING CONCENTRATE
16 OZ. BOTTLE
22.29
NU-CALGON LIQUID ICE MACHINE CLEANER
Liquid Ice Machine Cleaner is a food-grade phosphoric acid that is fast acting yet safe to use. It has been formulated for removing
scale deposits from ice machines and coffee urns, and does not give off any harsh fumes or contain chlorine or chlorides that would
attack stainless steel.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-420708
LIQUID ICE MACHINE CLEANER
1 GAL.
161.11
S1-420747
LIQUID ICE MACHINE CLEANER
13.2 OZ. BOTTLE
18.11
®
®
®
NU-CALGON MICROMET CRYSTALS, 6R MICROMET & MICROMET PLATES
This treatment has been used for more than 50 years to prevent scale formation in commercial and residential water systems. It
dissolves at about 25% per month and should be used on larger commercial ice makers. For most waters, the initial charge is 1 ounce
of Crystals for every 100 lbs. of ice made per day. Each month, 25% of the initial charge should be added to the feeder.6R Micromet
is a food-grade phosphate specifically formulated for inhibiting scale in ice machines and other equipment using low volumes of water.
6R Micromet is also used as the scale inhibiting compound in the Nu-Calgon Micro-Plus Treatment Systems. It requires replacement
only once every six months. Typically, the required dosage if 8 ounces for each 450 pounds of ice (50 gallons of water) per day.
The patented Micromet Plate season-treatment product is contained in a unique flowthrough package design. This design makes
simple to treat small cooling towers and evap condensers. One canister treats up to 10 tons for scale (5 tons for corrosion) for five to
six months.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-424384
S1-424397
S1-426584
S1-436488
MICROMET CRYSTALS
MICROMET CRYSTALS
6R MICROMET
SEASON TREAT MICROMET PLATES
50 LB.
5 LB.
50 LB.
1 5-LB. CANISTER
2022.61
243.82
2014.68
326.79
369
NU-CALGON MICRO-PLUS®
The complete all-in-one treatment for ice machines, coffee urns and brewers, beverage machines and other equipment or systems using water such as
humidifiers, steamers, etc. The Micro-Plus “in-line” treatment units contain 6R Micromet for the control of scale. They also contain high-grade activated carbon
for eliminating objectionable tastes and odors, and filter discs to remove silt and sediment as small as 20 microns. Micro-Plus is available in four sizes, and all
are constructed of a two-piece, spun-welded polypropylene design. They are provided with 1/4” FPT connections, allowing for the use of compression fittings,
flare fittings or “quick disconnect” fittings. When properly sized, Micro-Plus Treatment Systems will last up to six months.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-4612W3
S1-4613Y8
S1-4614Y8
S1-4615W3
MICRO-PLUS 4
MICRO-PLUS 8
MICRO-PLUS 16
MICRO-PLUS 2
112.11
163.39
230.71
68.43
NU-CALGON NICKEL SAFE ICE MACHINE CLEANER
Nickel Safe Ice Machine Cleaner is a specially formulated food-grade product for removing scale deposits from ice machines having
nickel-plated or tin-plated evaporators. It mixes to form a green solution which makes rinsing easier.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-428708
S1-428734
NICKEL SAFE ICE MACHINE CLEANER
NICKEL SAFE ICE MACHINE CLEANER.
1 GAL.
16 FL. OZ.
127.79
20.39
NU-CALGON EVAP-TREATTM
Preventative Maintenance & Treatment for Evaporative Coolers
Features:
• Prevents scale & corrosion
• Inexpensive—lasts all season
• Easy to install
• Increases pad life
• Maintains cooler performance
• Utilizes 6R Micromet a foodgrade NSF-certified polyphosphate
SOURCE 1 PART NO.
DESCRIPTION
COOLER SIZE
MLP $
S1-417304
S1-417306
EVAP-TREAT
EVAP-TREAT
UP TO 6500 CFM
UP TO 10000 CFM
44.36
52.11
370
Scale Removal/Descaling
NU-CALGON LIQUID SCALE DISSOLVER & SEASON START® "IMPERIAL GRADE" SCALE
REMOVER
Liquid Scale Dissolver is a hydrochloric (muriatic) acid that is formulated to remove calcium scales from cooling
towers and other watercooled equipment. It contains low-foaming corrosion inhibitors and a built-in pH color
indicator. pH test paper is included.
Season Start is a powdered sulfamic acid formulation that contains the best inhibitors available for protecting all
metals including galvanizing. It is the best and the safest dry acid cleaner available. It contains a built-in pH color
indicator as well as wetting and antifoaming agents.
Usage: As an initial charge, use 2.5 gallons of Liquid Scale Dissolver or 10 lbs. of Season Start (Imperial Grade
Scale Remover) for every 50 gallons of water in the system.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-433003
S1-433005
S1-433008
S1-436084
S1-436088
LIQUID SCALE DISSOLVER
SEASON START SCALE REMOVER
SEASON START IMPERIAL GRADE SCALE REMOVER, 10
LB.
2.5 GAL.
5 GAL.
1 GAL.
50 LB.
10 LB.
109.11
210.75
49.82
811.46
183.04
NU-CALGON NO. 31-TX ACID PUMP & HK-31 HOSE KIT
The No. 31-TX Acid Pump is a compact submersible pump designed for circulating strong acids and cleaning
solutions. All parts are constructed of acidresistant materials. Motor is protected by thermal overload that stops
pump if temperature exceeds 140°F.
The HK-31 Hose Kit is an accessory for use with the No. 31-TX Acid Pump.
The kit includes two 1/2-inch tubing adapters, two 10-foot sections of 1/2-inch clear plastic tubing and three hose
clamps.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-46030
S1-46040
31-TX ACID PUMP
HK-31 ACID PUMP HOSE KIT
397.93
119.11
NU-CALGON CALCI-SOLVE SCALE REMOVER
Features:
• Removes clogs from pipes and drains
• Gets rid of offensive odors in drains
• Economical and easy to use
• Will not harm lines or drain pipes
• Can be used on hot water heaters, boilers, steam equipment and more
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-413408
S1-413424
CALCI-SOLVE SCALE REMOVER
CALCI-SOLVE SCALE REMOVER
1 GAL
32 OZ
57.36
21.54
NU-CALGON VITAL-FLO TANKLESS WATER HEATER DESCALER KIT
The Vital-Flo Tankless Water Heater Descaler Kit is a complete service tool for descaling tankless water heaters. It consists of a 1/6
hp submersible descaler pump, a set of five foot 3/4" female hose threaded assemblies, and a 8 fluid ounce formulated descaler
solution packaged in a lidded four gallon chemical resistant container. The pump and hose assemblies in the kit are designed for
repeated use for ongoing descaling requirements. The lid on the canister has a port that allows the hose assemblies and electrical
cord to be feed through the lid while the lid is fastened to the canister. This feature provides added safety during the descaling
process in a residential, commercial or industrial location. The Vital-Flo Descaler is an effective, proven chemistry for tankless water
heat descaling. The solution is available separately and packaged so each bottle is appropriate for a typical service call.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-438701
S1-438702
KIT,DESCALER,VITAL-FLO TANKLESS
DESCALER,VITAL-FLO,8-OZ (M12)
533.50
15.61
371
NU-CALGON WINTER TREATTM
System heating boilers can be troubled with water related problems such as scale formation, sludge and
corrosion, which in turn can lead to other troublesome situations like foaming surging. Proper treatment with a
product like Winter-Treat can prevent these problems, enabling the steam boiler to perform at its designed
capacity. Winter-Treat will buffer and balance water conditions, preventing both scale corrosion while keeping
the boiler free of sludge. Winter-treat is a true multipurpose treatment.
Closed systems such as hot water heating boiler and even closed chilled water systems are easily plagued with
corrosion problems in the absence of treatment. Winter-Treat contains all the necessary ingredients to buffer the
water's pH and balance, passivating the metal surfaces and inhibiting corrosion.
In addition to all its preventative abilities, Winter- Treat also cleans boilers that are already fouled with deposits
and corrosion.
Application:
Add one quart of Winter-Treat for every 25 gallons of water and let it circulate through the system for 1-3 hours.
Drain, flush and treat the system with one quart for every 25 gallons.
Features:
• Emulsifies and cleans away rust, corrosion deposits and sludge
• Inhibits system corrosion, foaming and surging
• Inhibits lime scale
• Buffers and balances water conditions
• Typical use is one quart per 25 gallons of water
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-439008
S1-439032
WINTER TREAT
WINTER TREAT
1 GAL.
1 QT.
83.71
28.86
Smoke Candles, Pellets & Matches
ClenAir Smoke Signal
Smoke Signal generates smoke by chemical reaction eliminating costly equipment and time to pinpoint leaks.
Smoke tests will effectively and inexpensively reveal leaks in heating and air conditioning duct work, furnaces,
fireboxes, exhaust fans and smoke detectors. Smoke Signal is also excellent for observing air flow patterns,
evaluating exhaust systems and testing smoke detectors. Smoke Signal items contain no explosive materials.
Quickly Test: Ductwork, Furnaces, Smoke Detectors, Heat Exchangers, Fire Boxes, Exhaust Fans
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-NC-61302
S1-NC-61303
S1-NC-61304
S1-NC-61305
S1-NC-61306
Candle - 4000 CFT - 30 Sec.
Candle - 8000 CFT - 60 Sec.
Candle - 40,000 CFT - 2-3 Min.
Smoke Pen with 6 Wicks
Smoke Pen Refill - 6 Wicks
12
12
12
1
1
11.57
12.75
23.32
122.14
90.61
372
SMOKEYS
Smoke emitter cartridges provide effective, low cost leak testing of heat exchangers, air ducts, tanks and boilers.
Visual air balancing of HVAC systems. Cartridges produce clean, non-toxic, oil-free smoke through chemical
reaction. Use also for fire drills as well as the placement and testing of smoke alarms/detectors.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-14145
S1-14175
S1-14250
S1-14340
S1-14460
45 SECOND BURN TIME, 150 CU. FT. – 10/PACK
75 SECOND BURN TIME, 600 CU. FT. – 10/PACK
2-1/2 MINUTE BURN TIME, 1,100 CU. FT. – 5/PACK
4 MINUTE BURN TIME, 2,500 CU. FT. – 5/PACK
8 MINUTE BURN TIME, 18,000 CU. FT. – 1/PACK
29.89
33.50
50.00
102.71
208.00
NU-CALGON V-BELT DRESSING
V-Belt Dressing is specially formulated to penetrate and extend modern v-belt life. It is specially formulated and designed to maintain
v-belt efficiency and performance under today’s increasing performance requirements. It keeps belts pliable, prevents slippage and
does away with squealing and chattering.
SOURCE 1 PART NO.
DESCRIPTION
SIZE
MLP $
S1-408603
V-BELT DRESSING
16 OZ. AEROSOL
37.61
Windshield Washer Fluid
NU-CALGON ELITE PERFORMANCE WINDSHIELD WASHER FLUID
Nothing is more important in winter months than maximum freeze protection to prevent damage to wash lines and safeguard against
windshield re-freeze. Elite Performance Windshield Washer Fluid is independently tested to provide freeze protection to -20°F. Don’t
take chances with generic washer products, only Elite Performance offers certified protection.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-NC-61115
Elite Performance Windshield Washer Fluid - 1 gallon
6
10.82
373
—NOTES—
374
—NOTES—
375
—NOTES—
376
Cable Clamps & Ties
CABLE TIE ASSORTMENT PACK
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-7-5811
S1-7-5811-B
S1-7-711
S1-7-711-B
NATURAL CABLE TIE ASSORTMENT – 5”, 8”, AND 11”
BLACK CABLE TIE ASSORTMENT – 5”, 8”, AND 11”
NATURAL CABLE TIE ASSORTMENT – 7” AND 11”
BLACK CABLE TIE ASSORTMENT – 7” AND 11”
30 BAGS
30 BAGS
25 BAGS
25 BAGS
36.36
40.39
18.57
21.21
* Sol d by Standard Pack / M LP per singl e bag
HEAVY DUTY CABLE TIES
6.6 nylon, the heavy duty duct straps feature smooth insertion, and a locking mechanism that gives ductwork a
firm hold. Accommodates 7 to 15 inch duct. Tensioning tool for 32”+ allows operator to adjust strap to any
desired tension.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-7-L300
S1-7-P24
S1-7-P36
S1-7-P36B
TENSIONING TOOL FOR 120-175 LB. TIES
24” LONG – FITS UP TO 6” DUCT – 175 LB. TENSILE
36” LONG – BLACK – FITS UP TO 10” DUCT – 175 LB.
TENSILE
48” LONG – BLACK – FITS UP TO 14” DUCT – 175 LB.
TENSILE
1
50
50
50
55.68
0.50
0.57
0.61
50
50
1.18
1.21
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-WC02
S1-WC03
S1-WC04
S1-WC05
S1-WC06
S1-WC07
S1-WC08
S1-WC09
S1-WC10
S1-WC12
S1-WC14
S1-WC16
S1-WCA1
WIRE AND CABLE CLAMPS – 1/8” DIAMETER
WIRE AND CABLE CLAMPS – 1” DIAMETER
WIRE AND CABLE CLAMPS ASSORTMENT – 1/8” TO 1”
40
40
35
35
30
30
25
20
20
15
15
14
26
4.04
4.04
4.04
4.04
4.04
3.82
4.04
4.04
4.04
4.04
3.82
4.04
4.04
S1-7-P48
S1-7-P48B
WIRE & CABLE CLAMPS - NYLON
* M LP per Standard Pack
377
ALLIGATOR CLIPS
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ACK4
TWO RED AND TWO BLACK BOOTS WITH 4 CLIPS
9.07
COMPRESSOR TERMINALS
The only terminals recommended for the wiring of compressors. Made from a phosphorous bronze material to
allow for a very tight grip while allowing full current flow. Uses 12-8 AWG wire.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-CC32
S1-CC32C
COMPRESSOR TERMINALS – .250
COMPRESSOR TERMINALS – .250
6
100
4.04
52.29
*MLP per Standard Pack
FLAG FEMALE COMPRESSOR TERMINAL KIT
Parts S1-6258, S1-6271, S1-6259, S1-6273, S1-6270 in a four compartment, clear plastic box. Parts S1-6270
and S1-6273 are put in the same compartment.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6200HX
FLAG FEMALE COMPRESSOR TERMINAL KIT
28.93
FLAG FEMALE COMPRESSOR TERMINALS
Also known as hermetic header terminals, these non-insulated terminals are designed with a larger distance
between the “rolls” to allow for the rod in hermetic header applications. The increased distance allows the rod to
slip in between them. Parts S1-6258 and S1-6259 are notched for bending. The notches are cut between the
slip-on portion and the conductor barrel and enable the back of the slip-on portion to be folded against the
conductor barrel after the wire connection is made.
SOURCE 1 PART NO.
DESCRIPTION
S1-6258†
S1-6258CX†
S1-6259
S1-6259CX
S1-6270
S1-6270LX
S1-6271
FLAG FEMALE COMPRESSOR TERMINAL
378
WIRE
RANGE
16-14
16-14
12-10
12-10
12-8
12-8
18-16
FITS
STD. PACK
MLP $
.250 TAB
.250 TAB
.250 TAB
.250 TAB
.250 TAB
.250 TAB
.090 PIN
17
100
14
100
9
50
12
5.57
28.11
5.86
37.25
5.86
26.71
5.86
FLAG FEMALE COMPRESSOR TERMINALS
†T his terminal features insulation grip.
Connectors
BUTT CONNECTORS - INSULATED
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-B211
S1-B211C
S1-B222C
S1-B233
S1-B233C
S1-BA22
S1-BS22
BUTT CONNECTOR – 22-18 W
BUTT CONNECTORS – ASSORTED
SPLICE CONNECTORS – 18-14 W
18
100
100
11
100
16
10
4.04
19.61
19.61
4.04
32.11
4.04
4.04
* MLP per Standard Pack
INSULATED BUTT CONNECTOR ASSORTMENT KIT
Includes parts S1-6217, S1-6231, and S1-6232.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6200BSX
BUTT CONNECTOR ASSORTMENT KIT
5.61
INSULATED BUTT CONNECTORS
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STD. PACK
MLP $
S1-6217
S1-6231
S1-6232
S1-6232LX
S1-6287
INSULATED BUTT CONNECTOR
16-14
12-10
22-18
22-18
22-18
27
16
26
50
5
5.86
5.86
5.86
10.04
5.86
SOURCE 1 PART NO.
DESCRIPTION
AWG
STD. PACK
MLP $
S1-CPN1
S1-CPN1C
S1-CPN2
S1-CPN2C
S1-CPN3
S1-CPN3C
PORCELAIN WIRE CONNECTOR – SMALL
PORCELAIN WIRE CONNECTOR – SMALL
PORCELAIN WIRE CONNECTOR – MEDIUM
PORCELAIN WIRE CONNECTOR – MEDIUM
PORCELAIN WIRE CONNECTOR – LARGE
PORCELAIN WIRE CONNECTOR – LARGE
22-16, 2 STRAND WIRE
15
100
10
100
10
100
4.04
24.25
4.04
28.29
4.04
34.36
PORCELAIN WIRE CONNECTORS
379
Connectors
WIRE CONNECTORS - CONTRACTOR PACKS
U.L. Listed. CSA Approved.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-C222
S1-C222C
S1-C223
S1-C223C
S1-C241
S1-C243
S1-C245
S1-C247
S1-C312
S1-C312L
S1-C512
S1-C512L
CLOSED END CONNECTORS 22-14 W
BLUE WIRE CONNECTORS 22-16 W
ORANGE WIRE CONNECTORS 22-14 W
YELLOW WIRE CONNECTORS 18-10 W
RED WIRE CONNECTORS 18-10 W
YELLOW WINGED WIRE CONNECTORS – 3 - #12
YELLOW WINGED WIRE CONNECTORS – 3 - #12
RED WINGED WIRE CONNECTORS – 5 - #12
RED WINGED WIRE CONNECTORS – 5 - #12
18
100
15
100
20
15
13
10
13
50
10
50
4.04
25.11
4.04
30.32
4.04
4.04
4.04
4.04
4.04
13.96
4.04
18.36
WIRE CONNECTORS - SCREW-ON
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-WN100-BLU
S1-WN100-GRY
S1-WN100-ORN
S1-WN100-RED
S1-WN100-YLW
BLUE,72B,#22-#16 AWG,BOX OF 100
GREY,71B,#22-#16 AWG,BOX OF 100
ORANGE,73B,#22-#14 AWG,BOX OF 100
RED,76B,#18-#10 AWG,BOX OF 100
YELLOW,74B,#18-#10 AWG,BOX OF 100
7.86
6.86
8.79
14.32
11.00
WIRE CONNECTORS - WINGED
Wings give surer grip; offset center design provides great twisting leverage. Expandable square-wire spring instantly adjusts to shape
and size to create a strong, vibration resistant connection. Same tough shell as screwon type. U.L. Listed. C.S.A. Approved.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-623-000
S1-623-006
S1-623-007
S1-623-008
LG. GRAY WINGED – SIZE 78B, #14 TO #8 AWG, 600V MAX.
YELLOW WINGED – SIZE 84, #22 TO #10 AWG, 600V MAX.
RED WINGED – SIZE 86, #18 TO #10 AWG, 600V MAX.
BLUE WINGED – SIZE 88, #10 TO #6, 600V MAX.
50/BOX
100/BOX
100/BOX
50/BOX
18.21
14.18
21.21
22.21
BX SET SCREW CONNECTORS
BX cable range = .445 to .630 diameter. U.L. Listed. CSA Approved.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-640-845
TRADE SIZE – 3/8”
100
0.79
* Sold by Standard Package / M LP Per Each
380
LIQUID TITE CONNECTORS
For use with metallic and non-metallic liquid tite conduit, Type B. Provides smooth connection, no sharp edges to strip
wire. Wiring easily pulled through. U. L. Listed. C.U.L. Listed.
Metallic
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-750-MLT50
S1-750-MLT75
S1-750-MLT9050
S1-750-MLT9075
1/2” METALLIC STRAIGHT CONNECTOR
3/4” METALLIC STRAIGHT CONNECTOR
1/2” METALLIC 90 DEGREE ELBOW
3/4” METALLIC 90 DEGREE ELBOW
25
10
10
10
4.29
6.14
5.79
8.61
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-750-NMLT100
S1-750-NMLT150
S1-750-NMLT200
S1-750-NMLT4550
S1-750-NMLT4575
S1-750-NMLT50
S1-750-NMLT75
S1-750-NMLT90100
S1-750-NMLT90150
S1-750-NMLT90200
S1-750-NMLT9050
S1-750-NMLT9075
1” NON-METALLIC STRAIGHT CONNECTOR
1-1/2” NON-METALLIC STRAIGHT CONNECTOR
2” NON-METALLIC STRAIGHT CONNECTOR
1/2” NON-METALLIC 45 DEGREE ELBOW CONNECTOR
1/2” NON-METALLIC STRAIGHT CONNECTOR
3/4” NON-METALLIC STRAIGHT CONNECTOR
1” NON-METALLIC 90 DEGREE ELBOW
1-1/2” NON-METALLIC 90 DEGREE ELBOW
2” NON-METALLIC 90 DEGREE ELBOW
5
5
5
10
10
25
10
5
5
5
10
10
7.11
10.46
21.16
7.46
10.64
2.04
3.00
16.36
18.71
23.71
3.25
4.68
Non-Metallic
LIQUID TITE FLEXIBLE CONDUIT
Specifically for electrical applications. For outside, inside and industrial uses including transformer connections,
air conditioning and heating. Joins with metallic or non-metallic connectors, easy to cut. Conduit is impact
resistant, chemical resistant and will not kink. UL and CUL Listed. For use as indicated in Article 351 of the 1987
NEC.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-750-12100
S1-750-34100
CONDUIT, NON-METALLIC, 1/2” ID x 100’ ROLL
CONDUIT, NON-METALLIC, 3/4” ID x 100’ ROLL
119.50
152.07
381
SINGLE PIECE LIQUID TITE FITTINGS
Conduit threads onto ferrule and up inside the outer body. An inside taper squeezes down on the outside of
conduit for a superior liquid tight seal. The cut portion of the conduit does not show, giving a more finished
appearance. Easy to use at a lower cost than regular liquid tite fittings.
SOURCE 1 PART NO.
DESCRIPTION
S1-750-10100
S1-750-SLTC50
S1-750-SLTC75
S1-750-SLTC9050
S1-750-SLTC9075
CONDUIT, NON-METALLIC, 1" I.D. x 100' ROLL
1/2” STRAIGHT SCREW-ON FITTING
3/4” STRAIGHT SCREW-ON FITTING
1/2” 90° SCREW-ON FITTING
3/4” 90° SCREW-ON FITTING
STD. PACK
MLP $
25
25
25
25
342.71
2.11
2.96
3.29
5.07
CABLE STAPLES
Cable Staples for NMB Cable (Romex) and Copper Insulated Staples for thermostat wire.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-625-183
S1-625-IS5
ROMEX STAPLES – 1/2”
COPPER INSULATED #5 STAPLES FOR T-STAT WIRE
100
100
4.64
7.50
ELECTRICAL TOGGLE SWITCHES
Metal Bat Handle Toggle Switches
Bat handle toggle switch, sequence on-off, circuit single pole, single throw
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-ED447
SWITCH,TOGGLE,SPST,10A/277V-20A/125V AC
8.50
382
ELECTRICAL TOGGLE SWITCHES
Side wire design with automatic grounding and large binding head terminal screws for fast wiring. Lubricated
cam provides sm ooth lever action.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-620-601
S1-620-605
20A-1 HP 120V, SINGLE POLE, IVORY
15A-1/2 HP 120V, SINGLE POLE, IVORY
10
10
14.43
3.46
* Sol d by Standard Package/M LP Per Each
EMT (THINWALL) FITTINGS
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-625-304
S1-625-305
S1-625-800
S1-625-801
S1-625-810
S1-625-811
STRAP-ONE HOLE – 1/2”
STRAP-ONE HOLE – 3/4”
SET SCREW CONNECTOR – 1/2”
SET SCREW CONNECTOR – 3/4”
SET SCREW COUPLING – 1/2”
SET SCREW COUPLING – 3/4”
100
100
50
25
50
25
0.39
0.50
1.46
1.32
0.96
2.00
ROMEX CONNECTORS
Zinc plated die cast Romex connectors
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-PI320
S1-PI321
3/8", KNOCKOUT 1/2" - PACK OF 25
3/8", KNOCKOUT 1/2" - PACK OF 8
24.18
8.18
* Sold by Standard Package/MLP Per Each
383
ROMEX CONNECTORS - METALLIC
Cable connectors for Romex Wire. Zinc die-cast. U.L. Listed and C.S.A. Approved.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-750-RC841
S1-750-RC842
3/8” ROMEX CONNECTOR FOR 1/2” KNOCKOUTS
3/4” ROMEX CONNECTOR FOR 3/4” KNOCKOUTS
100
50
0.93
2.00
* Sold by Standard Package/MLP Per Each
SWITCH/PLUG COMBO
Use with air handlers and condensate pumps. Touch-A-Matic design, with exclusive spring loaded steel ball
mechanism for smooth, positive contact movement. Small neon pilot light ON when switch is ON, is built-in to
the switch on switch/receptacle. U.L. Listed. C.S.A. Approved.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-620-274W
WHITE 1P 3W GROUNDING—15A 120V
10
32.04
* Sold by Standard Package/M LP Per Each
384
Disconnects
SOURCE 1 AIR CONDITIONING DISCONNECTS
SOURCE 1 PART NO.
DESCRIPTION
AMPS
MLP $
S1-ACD30
S1-ACD60
S1-ACD60NF
S1-ECD60NF
FUSIBLE METAL DISCONNECT WITH DOOR
FUSIBLE METAL DISCONNECT WITH DOOR
NON-FUSIBLE METAL DISCONNECT WITH DOOR
LOW PROFILE NON-FUSIBLE METAL DISCONNECT WITH DOOR
30
60
60
60
27.93
31.89
23.11
22.82
DISCONNECTS – NOT INSULATED
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-D010
S1-D010C
S1-D011
S1-D011C
S1-D012
S1-D021
S1-D021C
S1-D022
S1-D022C
S1-D032
S1-D032C
S1-D033
S1-D033C
FEMALE DISCONNECT – 22-18 W. 0.110 (1/8”)
FEMALE DISCONNECT – 12-10 W 0.375 (3/8”)
30
100
30
100
30
30
100
30
100
25
100
10
100
4.04
11.36
4.04
11.36
4.04
4.04
11.36
4.04
11.36
4.04
13.79
4.04
33.54
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-DT-750-P60NF
DISCONNECT,PLASTIC,60A,NON-FUSIBLE
CASE/ORDER
QTY.
10
DIVERSITECH DISCONNECTS
385
55.21
Disconnects
SPECIAL DISCONNECTS
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-DMM2
S1-DMM2C
S1-DS20
S1-DS20C
S1-DS21
S1-DS21C
S1-DS22
S1-DS224
S1-DS224C
S1-DS22C
S1-DS23
S1-DS23C
S1-DS24
S1-DS24C
S1-DS25
S1-DS26
S1-DS26C
S1-DS27C
S1-DSC3
S1-DSC3C
S1-DXF1
S1-DXF1C
S1-DXF2
S1-DXF2C
S1-DXF3
S1-DXF3C
S1-DXM1
S1-DXM1C
S1-DXM2
S1-DXM2C
S1-DXM3
S1-DXM3C
DOUBLE MALE INSULATED – .250
DOUBLE MALE INSULATED – .250
STUD ADAPTER – #8, .250
F/M PIGGYBACK – 16-14 W. .250
F/M WIRE PIGGYBACK INSULATED – 16-14 W. .250
F/M WIRE PIGGYBACK INSULATED – 16-14 W. .250
F/M PIGGYBACK – 16-14 W. .250
F/M PIGGYBACK – .250 (VOLKSWAGON)
F/M PIGGYBACK – .250 (VOLKSWAGON)
F/M WIRE PIGGYBACK – 16-14 W. .250
F/M WIRE PIGGYBACK – 16-14 W. .250
STUD ADAPTER – .250, #6 SCREW
DOUBLE MALE SCREW MOUNT CONNECTOR
DOUBLE MALE SCREW MOUNT CONNECTOR
F/M OPEN BARREL PIGGYBACK
F/M PIGGYBACK – .250 (CHAIR)
F/M PIGGYBACK – .250 (CHAIR)
FULL INSULATED FEMALE DISCONNECT – 22-18 W. .250
FULL INSULATED MALE DISCONNECT – 22-18 W. .250
4
100
15
100
20
100
10
6
100
100
20
100
5
100
5
5
100
100
7
100
10
100
10
100
7
100
10
100
10
100
7
100
4.04
79.39
4.04
16.14
4.04
16.14
4.04
4.04
56.36
32.29
4.04
16.14
4.04
46.46
4.04
3.82
69.07
42.43
4.04
45.14
4.04
43.46
4.04
43.46
4.04
47.89
4.04
43.46
4.04
43.46
4.04
47.89
386
DISCONNECTS – INSULATED
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-D210
S1-D210C
S1-D211
S1-D211C
S1-D212
S1-D212C
S1-D220
S1-D220C
S1-D221
S1-D221C
S1-D222
S1-D222C
S1-D232
S1-D232C
S1-D233
S1-D233C
S1-DA22
S1-DM11
S1-DM11C
S1-DM12
S1-DM12C
S1-DM21
S1-DM21C
S1-DM22
S1-DM22C
S1-DM32
S1-DM32C
ASSORTED FEMALE DISCONNECTS
MALE DISCONNECT – 22-18 W. 0.187 (3/16”)
16
100
16
100
16
100
16
100
16
100
16
100
12
100
6
100
18
16
100
16
100
16
100
16
100
12
100
4.04
19.43
4.04
20.64
4.04
20.64
4.04
20.64
4.04
20.64
4.04
20.64
4.04
26.07
4.04
53.32
4.04
4.04
20.79
4.04
20.64
4.04
20.64
4.04
19.43
4.04
26.07
387
HIGH TEMPERATURE TERMINALS
DiversiTech high temperature terminals are made of nickel plated steel. The nickel plating prevents rust and
provides good electrical conductivity. They tolerate temperatures up to 900ºF and withstand vibration well.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-BH11
S1-BH11C
S1-BH22
S1-BH22C
S1-BH33
S1-BH33C
S1-DH11
S1-DH11C
S1-DH12
S1-DH12C
S1-DH21
S1-DH21C
S1-DH22
S1-DH22C
S1-DH32
S1-DH32C
S1-DHM21
S1-DHM21C
S1-DHM22
S1-DHM22C
S1-FH22
S1-FH22C
S1-FH32
S1-FH32C
S1-HTA2
S1-RH10
S1-RH10C
S1-RH11
S1-RH11C
S1-RH12
S1-RH12C
S1-RH13
S1-RH13C
S1-RH21
S1-RH21C
S1-RH22
S1-RH22C
S1-RH23
S1-RH23C
S1-RH30
S1-RH30C
S1-RH31
S1-RH31C
S1-RH32
S1-RH32C
S1-RH33
BUTT CONNECTORS – 22-18 W.
FEMALE DISCONNECTS – 22-18 W. 0.187 (3/16”)
MALE DISCONNECTS – 16-14 W. 0.187 (3/16”)
FLAG DISCONNECTS – 16-14 W. 0.250 (1/4”)
ASSORTED HI-TEMP TERMINALS
RING – 22-18 W. 6 STUD
RING – 22-18 W. 10 STUD
RING – 22-18 W. 10 STUD
RING – 22-18 W. 1/4 STUD
RING – 22-18 W. 1/4 STUD
RING – 16-14 W. 10 STUD
RING – 16-14 W. 10 STUD
RING – 16-14 W. 1/4 STUD
RING – 16-14 W. 1/4 STUD
RING – 12-10 W. 10 STUD
RING – 12-10 W. 10 STUD
RING – 12-10 W. 1/4 STUD
20
100
20
100
18
100
20
100
20
100
20
100
20
100
13
100
20
100
20
100
18
100
12
100
20
22
100
22
100
22
100
22
100
22
100
22
100
18
100
15
100
15
100
15
100
15
2.86
14.36
4.04
14.36
4.04
17.82
4.04
17.61
4.04
17.61
4.04
16.61
4.04
17.61
4.04
26.29
3.82
13.36
4.04
13.36
4.04
19.79
4.04
27.29
4.04
4.04
13.57
4.04
12.79
4.04
12.79
4.04
15.64
4.04
13.57
4.04
13.57
4.04
16.96
4.04
20.82
4.04
19.64
4.04
20.82
4.04
S1-RH33C
S1-RH34
S1-RH34C
S1-RH35
S1-RH35C
S1-RH43
S1-RH55
S1-RH65
S1-SH12
S1-SH12C
RING – 12-10 W. 1/4 STUD
RING – 12-10 W. 5/16 STUD
RING – 12-10 W. 5/16 STUD
RING – 12-10 W. 3/8 STUD
RING – 12-10 W. 3/8 STUD
RING – 8 WIRE, 1/4 STUD
SPADE – 22-18 W. 10 STUD
100
15
100
15
100
4
3
2
22
100
23.25
4.04
23.25
4.04
23.25
4.04
4.04
4.04
4.04
11.43
S1-SH22
S1-SH22C
S1-SH32
S1-SH32C
22
100
22
100
4.04
11.43
4.04
20.82
388
Disconnects & Rings
FLAG DISCONNECTS
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-FD21
S1-FD211C
S1-FD21C
S1-FD22
S1-FD222
S1-FD222C
S1-FD22C
S1-FD32
S1-FD32C
FLAG DISCONNECT – 16-14 W. .187
FULL INSULATED FLAG DISCONNECT – 22-18 W. .187
25
100
100
25
6
100
100
10
100
4.04
62.82
13.14
4.04
4.04
59.21
13.96
4.04
33.79
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-FR22
S1-FR22C
FLAG RING 16-14 W. 10 S.
FLAG RING 16-14 W. 10 S.
20
100
4.04
15.64
FLAG RINGS
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STUD
STD. PACK
MLP $
S1-6247
S1-6248
S1-6248CX
FLAG RINGS
FLAG RINGS
FLAG RINGS
16-14
12-10
12-10
#10
#10
#10
27
20
100
5.86
5.86
21.68
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STUD
STD. PACK
MLP $
S1-60216
S1-60216LX
S1-60245
S1-60245LX
S1-60246LX
S1-60247
S1-60247LX
S1-60252CX
S1-60253LX
S1-61202
S1-61202LX
S1-61208
S1-61208LX
S1-61212LX
S1-61252
S1-61252NX
S1-6216
S1-6216CX
S1-6216LX
S1-6236
S1-6236LX
S1-6252
S1-6252CX
S1-6252LX
S1-6253
S1-6253CX
S1-6253LX
S1-6257
S1-6257NX
S1-6272
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
INSULATED RINGS
16-14
16-14
16-14
16-14
22-18
12-10
12-10
12-10
12-10
22-18
22-18
22-18
22-18
12-10
8
8
16-14
16-14
16-14
22-18
22-18
12-10
12-10
12-10
12-10
12-10
12-10
8
8
16-14
1/4”
1/4”
3/8”
3/8”
#10
#6
#6
#8
3/8”
#6
#6
5/16”
5/16”
5/16”
5/16”
5/16”
#10
#10
#10
#8
#8
#10
#10
#10
1/4”
1/4”
1/4”
1/4”
1/4”
#6
20
50
17
50
50
17
50
100
50
22
50
17
50
50
5
25
23
100
50
22
50
17
100
50
15
100
50
6
25
22
5.86
12.18
5.86
13.14
10.50
5.86
13.68
26.39
20.50
5.86
11.07
5.86
15.29
20.50
5.86
24.39
5.86
21.86
11.89
5.86
11.46
5.86
29.64
15.75
5.86
34.14
17.96
5.86
21.79
5.86
INSULATED RINGS
389
Disconnects & Rings
INSULATED RINGS
NON-INSULATED RINGS
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STUD
STD. PACK
MLP $
S1-60202CX
S1-60203CX
S1-60205
S1-60205CX
S1-60206
S1-60206CX
S1-60215
S1-60215CX
S1-60236
S1-60236CX
S1-61205
S1-61205CX
S1-61207
S1-61207CX
S1-61209
S1-61209CX
S1-61211
S1-61211CX
S1-61213
S1-61213LX
S1-61245
S1-61245LX
S1-61247
S1-61247CX
S1-61272CX
S1-6215
S1-6215CX
S1-6215LX
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
NON-INSULATED RINGS
12-10
12-10
16-14
16-14
22-18
22-18
16-14
16-14
22-18
22-18
16-14
16-14
22-18
22-18
22-18
22-18
22-18
22-18
12-10
12-10
16-14
16-14
12-10
12-10
16-14
16-14
16-14
16-14
1/4”
#10
1/4”
1/4”
#10
#10
#10
#10
#8
#8
5/16”
5/16”
1/4”
1/4”
5/16”
5/16”
3/8”
3/8”
5/16”
5/16”
3/8”
3/8”
#6
#6
#6
#8
#8
#8
100
100
21
100
25
100
24
100
28
100
23
100
24
100
19
100
20
100
12
50
17
50
16
100
100
27
100
50
29.54
22.07
5.86
22.25
5.86
18.43
5.86
19.79
5.57
16.04
5.86
20.61
5.57
18.43
5.86
25.07
5.86
27.14
5.86
22.14
5.86
16.43
5.57
28.36
20.61
5.86
16.71
10.07
ELECTRICAL OUTLET BOXES, EXTENSIONS & COVERS
Standard Steel Utility (Handy) Boxes and Covers
Standard steel utility (Handy) boxes and covers. Conforms to Article 370 of NEC. U.L. Listed.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-620-200
S1-620-201
S1-620-20134
S1-620-202
S1-620-252
S1-620-253
S1-620-254
S1-620-255
1-1/2” DEEP, 1/2” K.O.S
1-7/8” DEEP, 1/2” K.O.S
1-7/8” DEEP, 3/4” K.O.S
2-1/8” DEEP, 1/2” K.O.S
FLAT, TWO DUPLEX RECEPTACLE COVER
FLAT, TOGGLE SWITCH COVER
FLAT BLANK COVER
FLAT COVER 1/2” K.O.
50
50
50
50
100
100
100
100
4.14
4.14
7.36
4.75
1.29
1.36
1.32
2.21
390
Standard Steel Utility (Handy) Boxes and Covers
4" Steel Octagon Outlet Box, Extensions and Covers
4” steel octagon outlet box, extensions and covers. Conforms to Article 370 of NEC. U.L. Listed.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-620-300
S1-620-301
S1-620-302
S1-620-303
S1-620-304
S1-620-306
1-1/2” DEEP, 1/2” AND 3/4” K.O.S
2-1/8” DEEP, 1/2” AND 3/4” K.O.S
1-1/2” DEEP, 1/2” K.O. EXTENSION
FLAT BLANK COVER
FLAT, DUPLEX RECEPTACLE COVER
FLAT COVER 1/2” K.O. IN CENTER
50
25
50
50
50
50
5.04
7.64
5.46
1.57
1.46
1.29
4" Steel Square Outlet Box, Extensions and Covers
4”
steel square outlet box, extensions and covers. Conforms to Article 370 of NEC. U.L. Listed.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-620-400
S1-620-401
S1-620-403
S1-620-404
S1-620-405
S1-620-406
S1-620-408
S1-620-409
S1-620-410
S1-620-411
S1-620-412
1-1/4” DEEP, 1/2” K.O.S
2-1/8” DEEP, 1/2” AND 3/4” K.O.S
1-1/2” DEEP, 1/2” K.O.S
1-1/2” DEEP, 1/2” AND 3/4” K.O.S EXTENSION
FLAT BLANK COVER
FLAT, ONE TOGGLE SWITCH COVER
FLAT, ONE DUPLEX RECEPTACLE COVER
FLAT, TWO TOGGLE SWITCH COVER
ONE SWITCH AND ONE DUPLEX RECEPTACLE COVER
FLAT, TWO DUPLEX RECEPTACLE COVER
50
25
50
50
50
50
50
50
50
50
50
7.00
5.11
3.93
7.61
1.71
1.68
4.57
3.79
2.96
5.57
2.96
391
4" Steel Square Outlet Box, Extensions and Covers
4-11/16” Steel Square Outlet Box Covers
4-11/16” steel square outlet box covers. Conforms to Article 370 of NEC. U.L. Listed.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-620-500
S1-620-501
S1-620-502
S1-620-503
2-1/8” DEEP, 1/2” AND 3/4” K.O.S
FLAT BLANK COVER
RAISED COVER FOR SINGLE DEVICE
25
25
25
25
11.43
2.18
7.21
3.82
Fuses
BUSS FUSES
Dual Element Time Delay 250 Volt, Class RK5
SOURCE 1 PART NO.
AMP
STD. PACK
MLP $
S1-FRNR10
S1-FRNR100
S1-FRNR12
S1-FRNR15
S1-FRNR20
S1-FRNR25
S1-FRNR30
S1-FRNR35
S1-FRNR40
S1-FRNR45
S1-FRNR50
S1-FRNR60
S1-FRNR70
10
100
12
15
20
25
30
35
40
45
50
60
70
10
5
10
10
10
10
10
10
10
10
10
10
5
5.07
15.36
6.11
4.75
3.82
3.82
3.82
7.00
7.00
7.00
7.00
7.00
16.68
* Sol d by Standard Pack / M LP per Each
392
Fuses
BUSS FUSES
Dual Element Time Delay 600 Volt, Class RK5
SOURCE 1 PART NO.
AMP
STD. PACK
MLP $
S1-FRSR10
S1-FRSR100
S1-FRSR12
S1-FRSR15
S1-FRSR20
S1-FRSR25
S1-FRSR30
S1-FRSR35
S1-FRSR40
S1-FRSR45
S1-FRSR50
S1-FRSR60
S1-FRSR70
10
100
12
15
20
25
30
35
40
45
50
60
70
10
5
10
10
10
10
10
10
10
10
10
10
5
10.18
31.93
10.18
8.25
8.25
8.25
8.25
15.46
14.11
15.46
14.11
14.11
31.93
FUSE, SUPPLEMENTAL
SOURCE 1 PART NO.
DESCRIPTION
VOLT
AMPS
STD. PACK
MLP $
S1-GMQ-3-2/10
FUSE,TIME DELAY,REJECTION,300V,3.2A
300
3.2
5
18.07
CARTRIDGE FUSES
SOURCE 1 PART NO.
DESCRIPTION
VOLT
AMPS
STD. PACK
MLP $
S1-FNQ15
S1-FNQ20
S1-FNQR1
S1-FNQR10
S1-FNQR3
S1-FNQR5
S1-KTKR1
CARTRIDGE FUSE; TIME DELAY
CARTRIDGE FUSE; TIME DELAY
CARTRIDGE FUSE; CLASS CC; TIME DELAY
CARTRIDGE FUSE; FAST ACTING; CC
REJECTION
REJECTION
REJECTION
REJECTION
REJECTION
REJECTION
500
500
600
600
600
600
600
15
20
1
10
3
5
1
10
10
10
10
10
10
10
14.54
14.54
15.46
16.61
15.61
15.79
12.89
600
10
10
12.89
600
15
10
12.89
600
20
10
12.89
600
3
10
12.89
600
5
10
15.71
S1-KTKR10
S1-KTKR15
S1-KTKR20
S1-KTKR3
S1-KTKR5
393
Fuses
CLASS G FUSE
Time Delay, 480V, UL Listed, CSA Certified
SOURCE 1 PART NO.
AMP
MLP $
S1-SC10
S1-SC15
S1-SC20
S1-SC30
S1-SC60
10
15
20
30
60
6.54
3.75
4.57
8.71
9.54
* M LP per each / Sold per standard package of 10
FUSE ADAPTERS
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-626-38632
S1-626-38636
FUSE ADAPTER – 60 TO 30 REDUCER FOR CLASS H, 250V
FUSE ADAPTER – 60 TO 30 REDUCER FOR CLASS H, 600V
13.25
13.32
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-FH-1
IN-LINE FUSE HOLDER
58.82
FUSE HOLDER, IN-LINE
394
Fuses
FUSE PULLER
• For fuse sizes 1/4" to 1/2"
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-626-38071
FUSE PULLER - 1/4" TO 1/2" FUSES
19.64
NON-RENEWABLE CARTRIDGE FUSES
SOURCE 1 PART NO.
AMP
STD. PACK
MLP $
S1-NON10
S1-NON100
S1-NON20
S1-NON30
S1-NON40
S1-NON50
S1-NON60
10
100
20
30
40
50
60
10
5
10
10
10
10
10
2.00
12.25
5.14
5.00
8.50
8.46
8.46
PLUG FUSES - FAST ACTING
Expels gases caused by the blowing fuse, but doesn’t allow flame to escape. Glass top for safety against shock.
Positive visual indication of OK condition or blown condition. Distinguishes between overload and dead short
conditions. Magnifying center of face. Shapes of face openings identify ratings. Meets Federal Specification WF791E/Gen. T ype 791/1. Base “W” Fast acting fuses. U.L. Listed.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-626-15
S1-626-20
S1-626-25
S1-626-30
PLUG FUSE – 15 AMP
4
4
4
4
2.50
2.50
2.50
2.50
TIME DELAY PLUG FUSES
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-626-10T
S1-626-15T
S1-626-20T
S1-626-25T
S1-626-30T
TYPE “T” PLUG FUSE – 10 AMP
4
4
4
4
4
8.93
5.25
5.25
5.96
5.25
395
Fuses
TIME DELAY PLUG FUSES
U.L. Listed.
TYPE "S" NON-TAMPER FUSES
Provides specific overcurrent protection. Time-delay element protects against premature blowing from motors in
air conditioners or compressors. Visual indication of good or blown condition. U.L. Listed. C.S.A. Approved.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-626-10S
S1-626-15S
S1-626-20S
S1-626-25S
S1-626-30S
S1-626-3S
S1-626-4S
S1-626-6S
TYPE “S” FUSE – 10 AMP
TYPE “S” FUSE – 3.2 AMP
TYPE “S” FUSE – 6.25 AMP
4
4
4
4
4
4
4
4
11.93
5.82
5.82
6.32
6.32
11.32
13.93
11.93
* Sold by Standard Package/M LP per Each
U.L. Listed.
BLADE (AUTO) FUSES
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-626-AT0003
S1-626-AT0005
BLADE FUSE – 3 AMP – PURPLE
BLADE FUSE – 5 AMP – TAN
100
100
1.11
1.11
396
These non-insulated terminals are constructed of nickel plated steel; rated at 900ºF (482ºC).
HIGH TEMPERATURE ASSORTMENT
Includes parts S1-4213, S1-4215, S1-4204, and S1-4254 .
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-4200AX
HIGH TEMP. ASSORTMENT
5.04
HIGH TEMPERATURE FEMALE SLIP-ONS
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
TAB SIZE
STD. PACK
MLP $
S1-4204
S1-4204CX
S1-4214
S1-4214CX
S1-4221
S1-4221CX
HIGH TEMP. FEMALE SLIP-ONS
12-10
12-10
16-14
16-14
16-14
16-14
.250
.250
.250
.250
.187
.187
17
100
21
100
20
100
3.68
17.64
3.68
15.07
3.68
15.39
HIGH TEMPERATURE FLAG FEMALE SLIP-ONS
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
TAB SIZE
STD. PACK
MLP $
S1-4213
S1-4213CX
S1-4224
S1-4224CX
S1-4224NX
HIGH TEMP. FLAG FEMALE SLIP-ONS
16-14
16-14
12-10
12-10
12-10
.250
.250
.250
.250
.250
16
100
11
100
25
3.68
19.57
3.68
26.64
7.43
HIGH TEMPERATURE MALE SLIP-ONS
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
TAB SIZE
STD. PACK
MLP $
S1-4219
S1-4219CX
S1-4220
S1-4220CX
HIGH TEMP. MALE SLIP-ONS
12-10
12-10
16-14
16-14
.250
.250
.250
.250
21
100
21
100
3.68
14.54
3.68
13.86
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STUD
STD. PACK
MLP $
S1-4205CX
S1-4206
S1-4206CX
S1-4215
S1-4215CX
S1-4247CX
S1-4252
S1-4252CX
S1-4253
S1-4253CX
HIGH TEMP. RINGS
HIGH TEMP. RINGS
HIGH TEMP. RINGS
HIGH TEMP. RINGS
HIGH TEMP. RINGS
HIGH TEMP. RINGS
HIGH TEMP. RINGS
HIGH TEMP. RINGS
HIGH TEMP. RINGS
HIGH TEMP. RINGS
16-14
22-18
22-18
16-14
16-14
12-10
12-10
12-10
12-10
12-10
1/4”
#6
#6
#10
#10
#6
#10
#10
1/4”
1/4”
100
23
100
21
100
100
14
100
14
100
18.61
3.68
12.82
3.68
13.96
19.71
3.68
20.11
3.68
22.21
HIGH TEMPERATURE RINGS
397
HIGH TEMPERATURE SPADES
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STUD
STD. PACK
MLP $
S1-4226
S1-4226CX
S1-4254CX
HIGH TEMP. SPADES
HIGH TEMP. SPADES
HIGH TEMP. SPADES
16-14
16-14
12-10
#10
#10
#10
23
100
100
3.68
12.71
17.07
Hook Terminals
HOOK TERMINALS – INSULATED
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-H211
S1-H211C
S1-H212
S1-H212C
S1-H221
S1-H221C
S1-H222
S1-H222C
S1-H231
S1-H231C
S1-H232
S1-H232C
HOOK – 22-18 W, 8 STUD
HOOK – 22-18 W, 10 STUD
HOOK – 22-18 W, 10 STUD
HOOK – 16-14 W, 10 STUD
HOOK – 16-14 W, 10 STUD
HOOK – 12-10 W, 10 STUD
HOOK – 12-10 W, 10 STUD
14
100
14
100
14
100
14
100
10
100
10
100
4.04
22.21
4.04
22.21
4.04
22.21
3.82
22.21
3.82
28.39
4.04
30.11
INSULATED HOOKS
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STUD
STD. PACK
MLP $
S1-6242
S1-6242LX
S1-6244
INSULATED HOOKS
INSULATED HOOKS
INSULATED HOOKS
22-18
22-18
16-14
#8
#8
#8
22
50
20
5.86
12.04
5.86
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STUD
STD. PACK
MLP $
S1-6243CX
NON-INSULATED HOOKS
16-14
#8
100
22.29
NON-INSULATED HOOKS
COMPRESSOR LEAD KIT
Kit includes three leads:
• Flag female compressor terminal (.250 tab; part S1-6259)
• Waterproof butt connector (12-10 wire range; part S1-62231)
• Piece of 10 gauge wire (6” or 12”)
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-60259HX
COMPRESSOR LEAD KIT WITH 12” WIRE
18.57
* ML P per Standard Pack
398
REPLACEMENT COMPRESSOR LEADS
Extreme heat within compressors typically causes failure of wiring insulation. This can cause corrosion to the inner strands of copper
within the wire used for compressor hook-up. This reduces the power flow to the compressor causing the unit to overheat and can
prevent the compressor from starting. A MINIMUM of 12” of wire must be removed. The DiversiTech Replacement Compressor Leads
are ideal for replacing this corroded wiring. 24” leads also available for replacing wire all the way to the contactor and capacitor.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-CC33
S1-CC33-18
S1-CC33-24
COMPRESSOR LEADS – 12” WITH BUTT
COMPRESSOR LEADS – 18” WITH BUTT
COMPRESSOR LEADS – 24” WITH RING
3
3
3
15.96
20.00
22.21
* ML P per Standard Pack
TERM LOK COMPRESSOR REPAIR KIT
Finally, a product that simplifies the repair of burned or damaged spade terminals when reconnecting or replacing a compressor. Fits
both non-burned and burned terminals. Connects to the compressor via precision brass cylinders that fit over the terminals and
connect with stainless steel set screws. Wires are permanently attached. Standard factory 600V, 65 strand machine wire. Easy to
install and guaranteed for the life of the compressor.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-TLC-3-10
S1-TLC-3-12
S1-TLC-3-8
3 WIRE, 10 GAUGE CONNECTION KIT
75.43
70.11
104.79
Monitors
MOTOR PROTECTION
Digital Three Phase Line Voltage Monitor
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-DTP-3
Digital 3-Phase Motor Protector
296.89
Pigtails
POWER SUPPLY CORDS
Features:
• Stranded bare copper conductors
• Grounding conductors
• PVC jacket
• Right or straight angle male plug
• 110 VAC
• 16 AWG x 6” long
SOURCE 1 PART NO.
DESCRIPTION
PLUG TYPE
MLP $
S1-PC6-90
S1-PC6-STR
CORD, PWR, 2-COND W/GND, 16-GA, 6’ (M50)
CORD, PWR, 2-COND W/GND, 16-GA, 6’ (M50)
90-DEGREE
STRAIGHT
7.21
7.21
399
DRYER & RANGE RECEPTACLES
U.L. Listed. C.S.A. Approved.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-625-1225
DRYER RECEPTACLE 30A 125/250V NEMA 14-30
10
40.64
ELECTRICAL DUPLEX RECEPTACLES
Automatic grounding for fast installation. Heavy duty mounting strap for additional assembly strength. Copper
alloy power/ground contacts for optimum continuity. Side wire design with large binding head terminal screws for
fast wiring. U.L. Listed. C.S.A. Certified (NEMA 5-15 T ype).
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-620-700
S1-620-701
S1-620-702
S1-620-703
S1-620-704
S1-620-705
S1-625-270W
S1-625-CR15W
S1-625-CR20W
15A, 125V, BROWN
15A, 125V, IVORY
20A, 125V, BROWN
20A, 125V, IVORY
15A, 125V, BROWN –RESIDENTIAL
15A, 125V, IVORY –RESIDENTIAL
15A 125V, WHITE –RESIDENTIAL
15A 125V, WHITE
20A 125V, WHITE
10
10
10
10
10
10
10
10
10
7.75
7.75
11.64
11.64
2.75
2.75
2.75
7.75
13.93
SQUARE D CIRCUIT BREAKERS
• QO Style Breakers with VISI-TRIP® (Visual Red Indicator in Window)
• UL & CSA Listed
Homeline® Circuit Breakers Double Pole, 120/240 VAC
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-HOM215
S1-HOM220
S1-HOM225
S1-HOM230
S1-HOM235
S1-HOM240
S1-HOM245
S1-HOM250
15 AMP
20 AMP
25 AMP
30 AMP
35 AMP
40 AMP
45 AMP
50 AMP
5
5
5
5
5
5
5
5
27.36
27.36
27.36
27.36
27.36
27.36
27.36
27.36
S1-HOM260
60 AMP
5
27.36
400
SQUARE D CIRCUIT BREAKERS
Homeline® Circuit Breakers Single Pole, 120/240 VAC
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-HOM115
S1-HOM120
S1-HOM125
S1-HOM130
S1-HOM140
S1-HOM150
15 AMP
20 AMP
25 AMP
30 AMP
40 AMP
50 AMP
10
10
10
10
10
10
12.00
12.00
12.00
12.00
12.00
12.00
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-QO225
S1-QO235
S1-QO245
25 AMP
35 AMP
45 AMP
5
5
5
29.46
29.46
29.46
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-QO125
S1-QO135
S1-QO145
25 AMP
35 AMP
45 AMP
10
10
10
12.79
12.79
12.79
QO Style Breakers Double Pole, 120/240 VAC
QO Style Breakers Single Pole, 120/240 VAC
401
SQUARE D DISCONNECT SWITCHES
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-HU362RB
60 AMP, 240/480/600 VOLT, NEMA 3R ENCLOSURE, 3 POLES,
DISCONNECT
60 AMP, 240 VOLT, 7.5-KILOWATT NON-FUSED AIR
CONDITIONER DISCONNECT
443.18
S1-QO200TRNM
402
77.61
Rings
RINGS – BRAZED SEAM – INSULATED
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-R242
S1-R242C
S1-R243
S1-R243C
S1-R244
S1-R244C
S1-R245
S1-R245C
S1-R252
S1-R252C
S1-R253
S1-R253C
S1-R254
S1-R254C
S1-R255
S1-R255C
S1-R256
S1-R256C
S1-RSA2
RING – 8 W. 10 STUD
RING – 8 W. 1/4 STUD
RINGS AND SPADES ASSORTED
4
100
4
100
4
100
4
100
3
100
3
100
3
100
3
100
3
100
15
4.04
77.71
4.04
77.71
3.82
82.43
3.82
77.71
4.04
109.89
4.04
109.89
4.04
110.93
4.04
104.54
3.82
126.21
3.82
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-R042
S1-R042C
S1-R043
S1-R043C
S1-R044
S1-R044C
S1-R045
S1-R045C
S1-R052
S1-R052C
S1-R053
S1-R053C
S1-R054
S1-R054C
S1-R055
S1-R055C
S1-R056
S1-R056C
5
100
5
100
5
100
5
100
3
100
3
100
3
100
3
100
2
100
4.04
58.50
4.04
58.50
4.04
62.04
4.04
62.04
4.04
96.75
4.04
96.75
4.04
96.75
4.04
96.75
4.04
141.00
RINGS – BRAZED SEAM – NOT INSULATED
403
Rings
RINGS – BUTTED SEAM – INSULATED
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-R210
S1-R211
S1-R211C
S1-R212
S1-R212C
S1-R213
S1-R213C
S1-R214
S1-R214C
S1-R215
S1-R215C
S1-R220
S1-R220C
S1-R221
S1-R221C
S1-R222
S1-R222C
S1-R223C
S1-R224
S1-R224C
S1-R225
S1-R225C
S1-R230
S1-R230C
S1-R231
S1-R231C
S1-R232
S1-R232C
S1-R233
S1-R233C
S1-R234
S1-R234C
S1-R235
S1-R235C
RING – 22-18 W. 10 STUD
RING – 22-18 W. 10 STUD
RING – 22-18 W. 1/4 STUD
RING – 22-18 W. 1/4 STUD
RING – 22-18 W. 5/16 STUD
RING – 22-18 W. 5/16 STUD
RING – 22-18 W. 3/8 STUD
RING – 22-18 W. 3/8 STUD
RING – 16-14 W. 10 STUD
RING – 16-14 W. 10 STUD
RING – 16-14 W. 1/4 STUD
RING – 16-14 W. 5/16 STUD
RING – 16-14 W. 5/16 STUD
RING – 16-14 W. 3/8 STUD
RING – 16-14 W. 3/8 STUD
RING – 12-10 W. 10 STUD
RING – 12-10 W. 10 STUD
RING – 12-10 W. 1/4 STUD
RING – 12-10 W. 1/4 STUD
RING – 12-10 W. 5/16 STUD
RING – 12-10 W. 5/16 STUD
RING – 12-10 W. 3/8 STUD
RING – 12-10 W. 3/8 STUD
16
16
100
16
100
12
100
12
100
12
100
16
100
16
100
16
100
100
12
100
12
100
12
100
12
100
12
100
10
100
10
100
10
100
4.04
4.04
20.64
4.04
20.64
4.04
26.46
3.82
26.46
4.04
28.11
4.04
19.43
4.04
20.64
4.04
20.64
26.46
3.82
28.11
3.82
28.11
4.04
28.11
4.04
26.46
4.04
28.11
4.04
32.75
4.04
30.89
4.04
30.89
404
Rings
RINGS – BUTTED SEAM – NOT INSULATED
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-R010
S1-R010C
S1-R011
S1-R011C
S1-R012
S1-R013
S1-R013C
S1-R014
S1-R014C
S1-R015
S1-R015C
S1-R020
S1-R020C
S1-R021
S1-R021C
S1-R022
S1-R023
S1-R023C
S1-R024
S1-R024C
S1-R025
S1-R025C
S1-R030
S1-R030C
S1-R031
S1-R031C
S1-R032
S1-R032C
S1-R033
S1-R033C
S1-R034C
S1-R035
S1-R035C
RING – 22-18 W. 10 STUD
RING – 22-18 W. 1/4 STUD
RING – 22-18 W. 1/4 STUD
RING – 22-18 W. 5/16 STUD
RING – 22-18 W. 5/16 STUD
RING – 22-18 W. 3/8 STUD
RING – 22-18 W. 3/8 STUD
RING – 16-14 W. 10 STUD
RING – 16-14 W. 1/4 STUD
RING – 16-14 W. 1/4 STUD
RING – 16-14 W. 5/16 STUD
RING – 16-14 W. 5/16 STUD
RING – 16-14 W. 3/8 STUD
RING – 16-14 W. 3/8 STUD
RING – 12-10 W. 10 STUD
RING – 12-10 W. 10 STUD
RING – 12-10 W. 1/4 STUD
RING – 12-10 W. 1/4 STUD
RING – 12-10 W. 5/16 STUD
RING – 12-10 W. 3/8 STUD
RING – 12-10 W. 3/8 STUD
30
100
30
100
30
20
100
20
100
20
100
30
100
30
100
30
20
100
20
100
20
100
20
100
20
100
20
100
15
100
100
15
100
4.04
10.96
4.04
10.32
4.04
4.04
15.04
4.04
15.96
4.04
15.96
4.04
10.32
4.04
10.96
4.04
4.04
15.96
4.04
15.96
4.04
15.96
4.04
15.04
4.04
15.96
4.04
15.96
4.04
22.82
22.82
4.04
21.54
Slip-Ons
COMBINATION PACK: SET OF S1-6233 & S1-6234
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
TAB SIZE
STD. PACK
MLP $
S1-61233LX
SET OF FULLY INSULATED M/F SLIP-ONS
16-14
.250
25 PAIRS
16.14
MLP $
FULLY INSULATED FEMALE SLIP-ONS
T he insulation on fully insulated slip-ons is vinyl or nylon.
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
TAB SIZE
STD. PACK
S1-61227†
FULLY INSULATED FEMALE SLIP-ON
16-14
.250
7
5.57
S1-61227NX†
12-10
.250
25
16.89
S1-61234LX
S1-6229††
S1-6229LX††
S1-6233
S1-6233CX
S1-6233LX
12-10
22-18
22-18
16-14
16-14
16-14
.250
.250
.250
.187
.250
.187
50
11
50
14
100
50
33.86
5.57
23.64
5.86
36.57
19.04
††T his terminal is usually supplied vinyl and has an insulation grip.
405
Slip-Ons
FULLY INSULATED MALE SLIP-ONS
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
TAB SIZE
STD. PACK
MLP $
S1-61235LX
S1-6234
S1-6234LX
FULLY INSULATED MALE SLIP-ON
12-10
16-14
16-14
.250
.250
.250
50
14
50
30.79
5.86
18.71
INSULATED FEMALE SLIP-ONS
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
TAB SIZE
STD. PACK
MLP $
S1-61223LX
S1-6218
INSULATED FEMALE SLIP-ON
12-10
16-14
.340
.250
50
22
25.29
5.86
S1-6218CX
S1-6218LX
S1-6235
S1-6235CX
S1-6235LX
S1-6251
S1-6251CX
S1-6251LX
S1-6281
S1-6281LX
S1-6282
S1-6282LX
16-14
16-14
22-18
22-18
22-18
12-10
12-10
12-10
16-14
16-14
22-18
22-18
.250
.250
.250
.250
.250
.250
.250
.250
.187
.187
.187
.187
100
50
22
100
50
17
100
50
22
50
22
50
21.82
11.64
5.86
22.07
12.14
5.86
27.93
15.61
5.86
11.07
5.86
11.29
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
TAB SIZE
STD. PACK
MLP $
S1-60214†
S1-60251
S1-6214
NON-INSULATED FEMALE SLIP-ON
16-14
12-10
16-14
.250
.250
.250
28
26
35
5.57
5.86
5.86
NON-INSULATED FEMALE SLIP-ONS
NON-INSULATED MALE SLIP-ONS
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
TAB SIZE
STD. PACK
MLP $
S1-61220
S1-61220CX
S1-6220
S1-6220CX
NON-INSULATED MALE SLIP-ON
16-14
16-14
16-14
16-14
.187
.187
.250
.250
37
100
38
100
5.86
13.29
5.86
12.93
406
Spade Terminals
BLOCK SPADES – 0.20 WIDE TO FIT TERMINAL BLOCKS
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-SN010
S1-SN010C
S1-SN020
S1-SN020C
S1-SN210
S1-SN220
S1-SN220C
UNINSULATED BLOCK SPADES – 22-18 W. 6 STUD
INSULATED BLOCK SPADES – 22-18 W. 6 STUD
30
100
30
100
16
16
100
4.04
10.32
3.82
10.32
4.04
4.04
19.43
INSULATED SPADES
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STUD
STD. PACK
MLP $
S1-60254
S1-60254CX
S1-60254LX
S1-61214
S1-61256LX
S1-6227
S1-6227LX
S1-6228
S1-6228LX
S1-6237
S1-6237LX
S1-6255
S1-6255CX
S1-6255LX
S1-6274
S1-6274LX
INSULATED SPADES
INSULATED SPADES
INSULATED SPADES
INSULATED SPADES
INSULATED SPADES
INSULATED SPADES
INSULATED SPADES
INSULATED SPADES
INSULATED SPADES
INSULATED SPADES
INSULATED SPADES
INSULATED SPADES
INSULATED SPADES
INSULATED SPADES
INSULATED SPADES
INSULATED SPADES
12-10
12-10
12-10
22-18
22-18
16-14
16-14
16-14
16-14
22-18
22-18
12-10
12-10
12-10
16-14
16-14
#8
#8
#8
#6
#10
#8
#8
#10
#10
#8
#8
#10
#10
#10
#6
#6
18
100
50
23
50
22
50
22
50
22
50
17
100
50
22
50
5.86
26.07
13.46
5.86
10.39
5.86
12.11
5.86
11.29
5.86
11.29
5.86
28.61
15.71
5.86
10.82
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STUD
STD. PACK
MLP $
S1-60255
S1-60255LX
S1-60256
S1-60256CX
S1-6238
S1-6238LX
S1-6239
S1-6239LX
S1-6276
S1-6276LX
INSULATED SPRING SPADES
12-10
12-10
12-10
12-10
22-18
22-18
16-14
16-14
16-14
16-14
#10
#10
#8
#8
#8
#8
#8
#8
#6
#6
16
50
17
100
22
50
22
50
21
50
5.57
13.82
5.71
27.61
5.86
11.93
5.86
11.93
5.86
11.93
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STUD
STD. PACK
MLP $
S1-61215
S1-61218
S1-61274
S1-61275
S1-6226
S1-6254CX
S1-6254LX
NON-INSULATED SPADES
22-18
12-10
12-10
16-14
16-14
12-10
12-10
#6
#8
#6
#6
#10
#10
#10
22
17
16
23
23
100
50
5.57
5.86
5.57
5.86
5.57
23.18
12.50
407
Spade Terminals
SNAP SPADE TERMINALS – INSULATED
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-SS210C
S1-SS211C
S1-SS212C
S1-SS220C
S1-SS221C
S1-SS222C
S1-SS230C
S1-SS231C
S1-SS232C
100
100
100
100
100
100
100
100
100
21.82
21.82
21.82
21.82
21.82
21.82
30.29
30.29
32.11
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-S210
S1-S210C
S1-S211
S1-S211C
S1-S212
S1-S212C
S1-S220
S1-S220C
S1-S221
S1-S221C
S1-S222
S1-S222C
S1-S230
S1-S230C
S1-S231
S1-S231C
S1-S232
S1-S232C
16
100
16
100
16
100
16
100
16
100
16
100
12
100
12
100
12
100
4.04
20.64
4.04
20.64
4.04
20.64
4.04
19.43
4.04
20.64
4.04
20.64
4.04
28.11
4.04
28.11
4.04
28.11
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-S010
S1-S010C
S1-S011
S1-S011C
S1-S020
S1-S020C
S1-S021
S1-S021C
S1-S022
S1-S022C
S1-S030
S1-S030C
S1-S031
30
100
30
100
30
100
30
100
30
100
22
100
22
4.04
10.96
4.04
10.96
4.04
10.32
4.04
10.96
4.04
10.32
4.04
15.04
3.82
S1-S031C
S1-S032
S1-S032C
100
22
100
15.04
4.04
15.96
SPADE TERMINALS – INSULATED
SPADE TERMINALS – NOT INSULATED
408
Spade Terminals & Slip-Ons
INSULATED FLANGE SPADES
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STUD
STD. PACK
MLP $
S1-61236
S1-61236LX
S1-61237
S1-61237LX
S1-61239
S1-61239LX
S1-61255
S1-61255LX
22-18
22-18
22-18
22-18
16-14
16-14
12-10
12-10
#6
#6
#8
#8
#6
#6
#10
#10
21
50
21
50
17
50
16
50
5.86
11.43
5.86
11.43
5.86
15.21
5.86
14.57
INSULATED MALE SLIP-ONS
The insulation on fully insulated slip-ons is vinyl or nylon.
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
TAB SIZE
STD. PACK
MLP $
S1-60219
S1-60220LX
S1-61221CX
S1-61221LX
S1-6219
S1-6219LX
INSULATED MALE SLIP-ON
22-18
16-14
12-10
12-10
16-14
16-14
.250
.187
.250
.250
.250
.250
23
50
100
50
22
50
5.86
10.71
28.57
15.04
5.86
11.39
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STUD
STD. PACK
MLP $
S1-61238
S1-61238CX
S1-61240
S1-61240CX
NON-INSULATED FLANGE SPADES
22-18
22-18
16-14
16-14
#8
#8
#10
#10
24
100
24
100
5.57
18.29
5.57
18.71
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STUD
STD. PACK
MLP $
S1-60226
NON-INSULATED SPRING SPADES
16-14
#8
24
5.57
S1-60226CX
S1-60238
S1-60238CX
S1-60240
S1-60240CX
16-14
22-18
22-18
16-14
16-14
#8
#8
#8
#10
#10
100
25
100
27
100
19.86
5.86
18.82
5.86
17.00
409
COMBINATION PACKS
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-6288
S1-6288LX
S1-6289
S1-6289LX
COMBINATION PACK INCLUDES PARTS S1-6283 AND S1-6284
7 PAIRS
25 PAIRS
7 PAIRS
25 PAIRS
5.86
17.50
5.86
17.46
FULLY INSULATED DEAD END CONNECTORS
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STD. PACK
MLP $
S1-6222
S1-6222LX
S1-6223
S1-6223LX
22-14
22-14
18-10
18-10
27
50
21
50
5.86
10.25
5.68
12.00
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STD. PACK
MLP $
S1-6284LX
S1-6286
FULLY INSULATED RECEPTACLES
22-18
16-14
50
12
21.21
5.86
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STD. PACK
MLP $
S1-6283
S1-6283LX
S1-6285
S1-6285LX
INSULATED PLUGS
INSULATED PLUGS
INSULATED PLUGS
INSULATED PLUGS
22-18
22-18
16-14
16-14
17
50
17
50
5.86
14.79
5.86
14.71
INSULATED PLUGS
TAB ADAPTERS – MALE TABS
SOURCE 1 PART NO.
DESCRIPTION
TAB SIZE
STUD
STD. PACK
MLP $
S1-6230
S1-6230CX
S1-6249
S1-6249CX
MALE TABS – STRAIGHT
MALE TABS – STRAIGHT
MALE TABS – 1 PAIR, BENT 90º
MALE TABS – 1 PAIR, BENT 90º
.250
.250
.250
.250
#8
#8
#8
#8
28
100
26
100
5.86
19.50
5.86
19.14
TAB ADAPTERS – PIGGY BACK SLIP-ONS
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STD. PACK
MLP $
S1-60210CX
S1-60210LX
S1-6210
S1-6210CX
INSULATED PIGGY BACK SLIP-ONS
INSULATED PIGGY BACK SLIP-ONS
NON-INSULATED PIGGY BACK SLIP-ONS
NON-INSULATED PIGGY BACK SLIP-ONS
16-14
16-14
16-14
16-14
100
50
20
100
45.04
23.50
5.86
24.57
410
TAB ADAPTERS – QUICK DISCONNECT WITH SCREW
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-6209
S1-6209LX
FITS .250 TAB, #6-32 x 1/4" SCREW
FITS .250 TAB, #6-32 x 1/4" SCREW
5
50
5.86
47.89
TAB ADAPTERS – SINGLE FEMALE DOUBLE MALE TABS
.250 male, .250 female.
SOURCE 1 PART NO.
DESCRIPTION
TAB SIZE
STD. PACK
MLP $
S1-60234
S1-6208
S1-6208LX
S1-6211
S1-6211CX
S1-6212
S1-6212CX
TAB ADAPTER; 1 FEMALE, 1 MALE; FULLY INSULATED
TAB ADAPTER; 1 FEMALE, 1 MALE; BENT 90º
TAB ADAPTER; 1 FEMALE, 1 MALE; BENT 90º
TAB ADAPTER; 1 FEMALE, 1 MALE; WYE
TAB ADAPTER; 1 FEMALE, 1 MALE; WYE
TAB ADAPTER; 1 FEMALE, 1 MALE; STACKED
TAB ADAPTER; 1 FEMALE, 1 MALE; STACKED
.250
.250
.250
.250
.250
.250
.250
12
12
50
27
100
16
100
5.86
5.86
25.46
5.86
17.36
5.86
29.18
TAP CONNECTORS
Designed to make tap splices.
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STD. PACK
MLP $
S1-6240
S1-6241
S1-6245NX
TAP SPLICE – YELLOW
TAP SPLICE – BLUE
TAP SPLICE – MATES WITH .250 TAB – BLUE
12-10
16-14
18-14
10 PIECES
15 PIECES
25 PIECES
5.57
5.86
14.07
Square D Air Conditioning Disconnects
SQUARE D THREE-PHASE DISCONNECTS
UL listed, File E5239. Meets UL98 for enclosed switches and NEMA Std. KS-1. Suitable as service entrance equipment when applied with neutral or ground
lug kit. Rainproof type 3R enclosure.
SOURCE 1 PART NO.
DESCRIPTION
VOLTAGE
MLP $
S1-750-30F-3PH
S1-750-60F-3PH
S1-750-60NF-3PH
DISCONNECT, MTL, 3-PH, 30A, FUSIBLE, DOOR
DISCONNECT, MTL, 3-PH, 60A, FUSIBLE, DOOR
DISCONNECT, MTL, 3-PH, 60A, NON-FUS, DOOR
240V MAX.
240V MAX.
240V MAX.
199.36
341.00
342.21
Storage Boxes
DIVERSITECH COMPARTMENTED STORAGE BOXES
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-MB21
S1-MB22
21 COMPARTMENTED METAL BOX
21 COMPARTMENTED METAL BOX WITH 230 POPULAR ITEMS INCLUDING
HI-TEMP AND COMPRESSOR TERMINALS, NYLON TIES AND CLAMPS
50.50
101.00
411
Storage Boxes
DIVERSITECH TRANSPARENT PLASTIC BOXES WITH TERMINAL ASSORTMENTS
Boxes are made of soft, pliable, durable “K” resin with 18 compartments containing the most popular terminals, including hi-temp and
compressor terminals.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-PA10
S1-PA18
S1-PA25
S1-PA25AP
180 TERMINALS (10 EACH KIND)
“K” RESIN PLASTIC BOX ONLY
450 TERMINALS (25 EACH KIND)
APPLIANCE PARTS TECHNICIAN ASSORTMENT – MOSTLY HI-TEMP
60.61
20.21
112.75
105.00
Waterproof Solderless Terminals
Waterproof terminals are assembled with high grade heat shrinkable insulation.When heated, the insulation shrinks
around the crimped connection and wire, sealing out moisture and corrosion. It also offers a wire insulation grip for
severe vibration applications.
FULLY INSULATED WATERPROOF FEMALE SLIP-ONS
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
TAB SIZE
STD. PACK
MLP $
S1-62235
FULLY INSULATED FEMALE SLIP-ONS
22-18
.250
3
5.86
WATERPROOF BUTT CONNECTORS
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STD. PACK
MLP $
S1-62217
S1-62231
16-14
12-10
3
3
5.86
5.86
WATERPROOF RINGS
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STUD
STD. PACK
MLP $
S1-62236
S1-62273
WATERPROOF RINGS
WATERPROOF RINGS
22-18
16-14
#8
#8
5
4
5.57
5.86
SOURCE 1 PART NO.
DESCRIPTION
WIRE RANGE
STUD
STD. PACK
MLP $
S1-62227
WATERPROOF SPADES
16-14
#8
5
5.57
WATERPROOF SPADES
412
Whips
AIR CONDITIONING WHIPS
Convenience Kit - Metallic Fittings
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6124
S1-6126
S1-6344
S1-6346
1/2” x 4’
1/2” x 6'
3/4” x 4’
3/4” x 6’
30.96
37.93
45.1
55.70
* Due to the fluctuati on i n the copper m etal m arket, M LPs are subject to change wi thout noti ce.
Convenience Kit - Non-Metallic Fittings
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6124NM
S1-6126NM
S1-6344NM
S1-6346NM
1/2” x 4’
1/2” x 6’
3/4” x 4’
3/4” x 6’
25.07
32.04
34.95
43.54
* Due to the fluctuati on i n the copper m etal m arket, M LPs are subject to change wi thout noti ce.
Wire
HIGH TEMPERATURE WIRE, 400°F, 600 V.
7 strand tin coated copper wire with silicone rubber insulation protected by a braided fiberglass jacket. Use on the front of all gas
furnaces with spark ignition because of flame roll-out on start up. Also on all power feeds to electric strip and duct heaters. Also used
on all heat producing food preparation equipment.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-WHT20
S1-WHTB10-20
S1-WHTB10-50
S1-WHTB12-20
S1-WHTB12-50
S1-WHTB14-50
S1-WHTR14-50
S1-WHTW14-50
14 GAUGE, 10 FT. BLACK, 10 FT. WHITE
10 GAUGE, BLACK, 20 FT.
14 GAUGE, RED, 50 FT.
14 GAUGE, WHITE, 50 FT.
30.68
58.79
197.46
38.32
95.82
76.68
69.68
76.68
STRANDED COPPER WIRE IN CLEAR DISPENSER PACK
UL, 600 V, 90°C Stranded T HHN wire. 19 strand copper.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-W101
S1-W102
S1-W103
S1-W104
S1-W105
S1-W121
S1-W122
S1-W123
S1-W124
S1-W125
S1-W141
S1-W142
S1-W143
S1-W144
S1-W145
S1-W801
S1-W802
S1-W803
S1-W804
S1-W805
10 GAUGE, 10 FT., BLACK
10 GAUGE, 10 FT., RED
10 GAUGE, 10 FT., GREEN
10 GAUGE, 10 FT., BLUE
10 GAUGE, 10 FT., WHITE
23.71
23.71
23.71
23.71
23.71
23.25
23.25
23.25
23.25
23.25
16.32
16.32
16.32
16.32
22.07
27.00
27.00
27.00
27.00
27.00
413
Wire
STRANDED COPPER WIRE ON SPOOL
100 Ft. Spool
UL, 600 V, 90°C Stranded T HHN wire. 19 strand copper. 100 ft. per spool.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-W101-100
S1-W102-100
S1-W103-100
S1-W104-100
S1-W105-100
S1-W121-100
S1-W122-100
S1-W123-100
S1-W124-100
S1-W125-100
S1-W141-100
S1-W142-100
S1-W143-100
S1-W144-100
S1-W145-100
S1-W801-100
S1-W802-100
S1-W803-100
S1-W804-100
S1-W805-100
10 GAUGE, 100 FT. SPOOL, BLACK
10 GAUGE, 100 FT. SPOOL, RED
10 GAUGE, 100 FT. SPOOL, GREEN
10 GAUGE, 100 FT. SPOOL, BLUE
10 GAUGE, 100 FT. SPOOL, WHITE
154.50
154.50
154.50
154.50
154.50
104.07
104.07
104.07
104.07
104.07
76.68
76.68
76.68
76.68
76.68
264.61
264.61
264.61
264.61
264.61
50 Ft. Spool
UL, 600 V, 90°C Stranded T HHN wire. 19 strand copper. 50 ft. per spool.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-W101-50
S1-W102-50
S1-W103-50
S1-W104-50
S1-W105-50
S1-W121-50
S1-W122-50
S1-W123-50
S1-W124-50
S1-W125-50
S1-W141-50
S1-W142-50
S1-W143-50
S1-W144-50
S1-W145-50
S1-W801-50
S1-W802-50
S1-W803-50
S1-W804-50
78.07
78.07
78.07
78.07
78.07
52.96
52.96
52.96
52.96
52.96
38.57
38.57
38.57
38.57
38.57
132.43
132.43
132.43
132.43
414
Wire
THERMOSTAT WIRE
Southwire Thermostat Wire
SOURCE 1 PART NO.
DESCRIPTION
LENGTH (FT.)
ORDER QTY.
MLP $
S1-TTW14-4-250
S1-TTW14-4-50
S1-TW10
S1-TW12
S1-TW14
S1-TW2
S1-TW2P
S1-TW3
S1-TW3P
S1-TW4
S1-TW4M-250
S1-TW4M-35
S1-TW4M-50
S1-TW4P
S1-TW4SPS-250
S1-TW5
S1-TW5P
S1-TW5SPS-250
S1-TW6
S1-TW6P
S1-TW6SPS-250
S1-TW7
S1-TW8
S1-TW8P
S1-TW8SPS-250
14-4,600V,STRANDED
14-4,600V,STRANDED
18 GA,10 COND
18 GA,12 COND
14GA,4 COND,STRD,SHLD
18 GA,2 COND
18GA,2 COND,PLNM RTD
18 GA,3 COND
18 GA,4 COND
18GA,4COND,MINISPLIT
18GA,4 COND,MINISPLIT
18GA,4 COND,MINISPLIT
18GA,4COND,SHLD,STRD
18 GA,5 COND
18 GA,6 COND
18 GA,7 COND
18 GA,8 COND
250
50
250
250
250
500
500
500
500
250
250
35
50
250
250
250
250
250
250
250
250
250
250
250
250
1
4
4
2
1
4
4
4
4
4
20
20
20
4
2
4
4
4
4
4
4
4
4
4
4
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
See Note 1 Below
Note1: REFER T O WEEKLY COMMODITY PRICE SHEET FOR MLP
Wire Ties
BLACK NYLON TIES WITH MOUNTING HOLE
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-WTMB05
S1-WTMB05C
S1-WTMB07
S1-WTMB07C
S1-WTMB11
S1-WTMB11C
S1-WTMB14
S1-WTMB14C
BLACK WIRE TIES WITH MOUNTING HOLE – 5” NYLON
12
100
10
100
6
100
5
100
4.04
24.39
4.04
31.14
4.04
60.21
4.04
63.04
415
Wire Ties
BLACK NYLON WIRE TIES
Ultraviolet resistant for outdoor use.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-WTB11C
S1-6263BCX
S1-6266BLX
S1-WTB05
S1-WTB05C
S1-WTB07
S1-WTB07C
S1-WTB07M
S1-WTB11
S1-WTB11D
S1-WTB11M
S1-WTB15
S1-WTB15C
S1-WTBA1
BLACK WIRE TIES – 11” NYLON
BLACK WIRE TIES - 11"
BLACK WIRE TIES - 36"
BLACK WIRE TIES – ASSORTED 4”, 7”, AND 11” NYLON
100
100
50
35
100
30
100
1000
15
500
1000
12
100
28
21.21
18.64
33.68
4.04
8.43
4.04
9.29
92.89
4.04
50.93
190.86
4.04
24.89
4.04
WHITE NYLON TIES WITH MOUNTING HOLE
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-WTM05
S1-WTM05C
S1-WTM07
S1-WTM07C
S1-WTM11
S1-WTM11C
S1-WTM14
S1-WTM14C
WHITE WIRE TIES WITH MOUNTING HOLE – 5” NYLON
13
100
11
100
6
100
5
100
3.82
23.46
4.04
30.11
4.04
54.75
4.04
65.25
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-WT04
S1-WT04C
S1-WT05
S1-WT05C
S1-WT07
S1-WT07C
S1-WT11
S1-WT11C
S1-WT15
S1-WT15C
S1-WTA1
WHITE WIRE TIES – 4” NYLON
WHITE WIRE TIES – ASSORTED 4”, 7”, AND 11” NYLON
40
100
35
100
30
100
15
100
12
100
30
4.04
5.14
4.04
8.11
4.04
8.89
4.04
18.21
4.04
25.25
4.04
WHITE NYLON WIRE TIES
416
Test Instruments
ANALOG POCKET THERMOMETERS
DiversiTech Analog Pocket Thermometer with Magnifying Lens
• Range 6-320: -40º to 160ºF
• Range 6-321: -0º to 220ºF
• Rugged stainless steel probe
Includes: Protective sheath with pocket clip.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-320
S1-6-321
ANALOG POCKET THERMOMETER: RANGE -40º TO 160ºF
ANALOG POCKET THERMOMETER: RANGE -0º TO 220ºF
16.79
9.64
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-HDT303K
DELUXE DIGITAL POCKET THERMOMETER
44.25
POCKET THERMOMETERS
DiversiTech Deluxe Digital Pocket Thermometer
•
•
•
•
•
•
•
•
Water and Drop Resistant, Rugged Construction
Data Hold
F/C Switch
On/Off Switch
Auto Power Off
2.5” Probe
Protective Cover with Clip
-40ºF to 300ºF, -40ºC to 150ºC
DiversiTech Pocket Thermometers
1” diameter dials with 5” stems (.145 dia.). Adjustable for recalibration. All stainless steel construction. Polycarbonate crystal. 1%
accuracy full scale. Plastic pocket sheath included.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-TD-1
S1-TD-2
POCKET THERMOMETER – 0 +220°F
POCKET THERMOMETER – -40ºF TO 160°F
12
12
7.07
7.89
*Sol d by case / M LP per each
417
Test Instruments
INFRARED THERMOMETERS
DiversiTech 12:1 S/B Refrigeration, A/C & Food Service Infrared Thermometer
Ideal for subcooling applications, particularly food service, refrigeration and air conditioning.
• Switchable ON/OFF Laser sighting
• ºF/ºC Switchable
• Backlit LCD Display
• Auto Measuring
• Extended, long time measuring reliability
• Temperature data storage
• Low Battery indication
• Ultra-low power consumption in shutdown mode
• Electronic trigger lock
• Ergonomic design
• Distance to spot ratio: 12:1
• Range: -58º to 600ºF (-50º to 316ºC)
• Emissivity: Fixed at 0.97
• Accuracy (@ ambient temperature of 77ºF/25ºC):
±5ºF (±3ºC) within -58º to -22ºF (-50º to -30ºC)
±3ºF (±2ºC) within -22º to 212ºF (-30º to 100ºC)
±2% within 212º to 600ºF (100º to 316ºC)
• Thermopile: 8 ~ 14 m
• Repeatability: ±2ºF (±1ºC)
• Resolution: 0.1ºF (0.1ºC)
• Response Time: 500 ms.
• Operating Temperature: 32º to 122ºF (0º to 50ºC), 10 to 90%RH
• Auto Power Off: Automatic after approx. 6 seconds
• Battery Life: 16 hours
• Dimensions: 6.69” x 5.23” x 1.77” (170x133x45mm)
• Weight: 5.8 oz. (163 g) Approx.
Includes: 1 “9V” battery; Instruction manual; carrying case.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-IRT656
12:1 S/B REFRIGERATION, A/C, AND FOOD SERVICE INFRARED THERMOMETER
301.93
418
Test Instruments
DiversiTech 30:1 High Performance Ultra Wide-Range Infrared Thermometer
High precision and high performance unit, can be used in most industrial applications, including furnaces and heat exchangers.
• Switchable ON/OFF Laser sighting
• ºF/ºC Switchable
• High/Low Audible Alarm
• Min/Max/Avg
• Auto Measuring
• Extended, long time measuring reliability
• 10 point memory
• Temperature data storage
• Low Battery indication
• Ultra-low power consumption in shutdown mode
• Electronic trigger lock
• Ergonomic design
• Range: -25.6º to 1400ºF (-32º to 760ºC)
• Emissivity: Adjustable 0.1 to 1.0
• Accuracy (@ ambient temperature of 77ºF/25ºC):
±5ºF (±3ºC) within -25.6º to -4ºF (-32º to -20ºC)
±3ºF (±2ºC) within -4º to 212ºF (-20º to 100ºC)
±2% within 212º to 1400ºF (100º to 760ºC)
• Thermopile: 8 ~ 14 m
• Repeatability: ±2ºF (±1ºC)
• Resolution: 0.1ºF (0.1ºC)
• Response Time: 500 ms.
• Operating Temperature: 32º to 122ºF (0º to 50ºC), 10 to 90%RH
• Auto Power Off: Automatic after approx. 6 seconds
• Battery Life: 16 hours
• Dimensions: 7.8” x 6.5” x 2” (200x166x51mm)
• Weight: 10.6 oz. (300 g) Approx.
Includes: 1 “9V” battery; instruction smanual; carrying case.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-IRT670
30:1 HIGH-PERFORMANCE ULTRA WIDE-RANGE INFRARED THERMOMETER
753.43
DiversiTech Pocket HVAC General Purpose Infrared Thermometer
Convenient and accurate measurement in most HVAC/R application and industrial jobs.
• Easy to use
• Auto power off
• Lock function
• Min/Max readings
• Fits in your pocket
• Emissivity: Fixed at 0.95
• Accuracy: ±0.6º ºF/ºC
• Response time: 1 second
Includes: 1 “9V” battery; neck strap.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-IRT203
POCKET HVAC INFRARED THERMOMETER (BLISTER PACKED)
288.25
419
Test Instruments
DiversiTech Pocket HVAC General Purpose Infrared Thermometer
For use in labs, industrial control and audits and measuring differential temperature T1/T2.
• Dual probe input
• Accepts K-type thermocouple probes
• T1/T2 temperature differential
• Data hold
• Max hold
• ºF/ºC switch
• Auto power off
• CE approved
• Accuracy: ±1.8ºF from -22º to 302ºF (±4ºF at all other ranges); ±1ºC from -30º to 150ºC (±2ºC at all other ranges)
• Probe length: 5” with 3 ft. cord
Includes: 1 “LR44” battery; molded hard case; 2 “K” type beaded tip probes.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-DT8803
DIGITAL THERMOMETER WITH 2 K-TYPE PROBES AND CASE
247.50
REFRIGERATOR/FREEZER/OVEN THERMOMETERS
DiversiTech Horizontal Refrigerator/Freezer Analog Thermometer
•
•
•
•
•
•
Horizontal reading
Hanging or free standing
Easy to read display
ºF and ºC scales
Range: -40º to 80ºF (-40º to 27ºC)
Dimensions: 1.25” x 4.75” x 0.75”
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-FT80H
HORIZONTAL REFRIGERATOR/FREEZER ANALOG THERMOMETER
11.14
DiversiTech Refrigerator/Freezer Analog Thermometer
•
•
•
•
•
•
•
Stainless steel
Easy-to-read round dial
ºF only
Temperature Indicators
Range: -20º to 80ºF (-29º to 27ºC)
Dial diameter: 2.5”
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-FT80R
REFRIGERATOR/FREEZER ANALOG THERMOMETER
14.36
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-OT550
REFRIGERATOR/OVEN THERMOMETER
12.43
DiversiTech Refrigerator/Oven Thermometer
•
•
•
•
•
•
•
Stainless steel
Easy-to-read round dial
ºF/ºC
Temperature Indicators
Range: 150º to 600ºF (50º to 300ºC)
Dial diameter: 2.5”
420
Test Instruments
TEMPERATURE HUMIDITY DATA LOGGERS
DiversiTech Temperature Humidity Data Logger with On/Off Switch
For professional use in monitoring and recording temperature and humidity.
• Records relative humidity and temperature
• Logs data for days, weeks or months
• Multiple data loggers can be programmed and data downloaded from a single docking station
• Programmable sampling rate from 1 sec. to 2 hrs.
• View either temperature or humidity on LCD
• Program the data logger, analyze and store data using software model S1-6-INT8819 (not included)
• Yellow record LED flashes when unit is sampling
• Scheduled, magnetic or immediate start capability
• Real time clock stores date and time with data
• Programmable high and low limits with alarm
• Humidity Range: 0 to 100%RH
• Accuracy: ± 1ºF from -4º to 122ºF, (-20º to 50ºC) ± 2ºF at all other ranges; ±5% RH
• Resolution: 0.1º, 0.1% RH
• Memory: Temp: up to 8,000; RH: 8,000 points
• Dimensions: 3.14” x 2.16” x 0.86”
• Weight: 2.6 oz. (76g)
Includes: Lithium battery.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-DL8835
TEMPERATURE HUMIDITY DATA LOGGER WITH ON/OFF SWITCH
340.93
DiversiTech USB Interface Kit
For downloading readings to your PC. Includes: Data logger base, USB1.1 cable, software, operation manual.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-INT8819
USB INTERFACE KIT
214.86
TEMPERATURE/HUMIDITY TESTERS
DiversiTech Digital Temperature & Humidity Pen
Ideal for HVAC, laboratories, hospitals, computer rooms, greenhouses, printing, film processing, and more.
• Simultaneous displays temperature and humidity
• Data hold freezes measured values
• ºF/ºC switch
• Auto power off after 20 minutes
• Min/Max memory
• Fits in your shirt pocket
• Range: 14º to 122ºF (-10º to 50ºC)
• Humidity range: 20 to 90% RH
• Temperature accuracy: ±1.8ºF (±1ºC)
• Humidity accuracy: ±5%
• Resolution: ±0.1º, 1% RH
• Dimensions: 5.9” x 0.8” x 0.6”
Includes: 1 “CR2032” battery; pocket clip on back.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-PTH8708
DIGITAL TEMPERATURE AND HUMIDITY PEN
186.75
421
Test Instruments
TEMPERATURE/HUMIDITY TESTERS
DiversiTech Economy Temperature & Humidity Pen
Hand-held convenience for accurate measurement of temperature and humidity.
• Simultaneous display of relative humidity and temperature
• ºF/ºC switch
• Pocket size for quick & reliable measurements at any location
• Min/Max memory (temp & humidity)
• “Clear” function erases stored readings to record new values
• Humidity range: 20 to 90% RH
• Range: 14º to 122ºF (-10º to 50ºC)
• Humidity accuracy: ±5%
• Temperature accuracy: ±1.8ºF (±1ºC)
• Resolution: ±0.1º; 1% RH
• Dimensions: 5.9” x 0.8” x 0.6”
Includes: 1 “LR44” battery; protective cover with clip.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-LAM122
ECONOMY TEMPERATURE AND HUMIDITY PEN
157.75
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-DTH03
JUMBO THERMO/HYGROMETER
89.14
THERMO/HYGROMETERS
DiversiTech Jumbo Display – Thermo/Hygrometer
•
•
•
•
•
•
•
Displays Inside Humidity and Temperature
Jumbo Display (3” x 1.5”)
2 Key Operation: Min/Max and Reset
Memory for High and Low Temp.and Humidity
Wall or Desk Mount
Low Battery Indicator (Battery Included)
14°F to 122°F (-10ºC to 50ºC)
THERMOMETERS
DiversiTech Digital Thermometer
Temperature range from -40° F to 230° F. Packaged on attractive display card.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-541-300
DIGITAL THERMOMETER
32.29
422
Test Instruments
DISPLAY THERMOMETERS & DIGITAL PANEL METERS
DiversiTech Digital Jumbo Display Service Thermometer
For use in labs, industrial control and food service applications.
• Displays ambient temperature and remote temperature via probe
• Temperature alarm function with high & low limits
• Audible & visual alarm set points
• Probe is immersible in water
• Clock displays hours & minutes
• Sensor wire compartment
• Resolution: 0.1º
• Accuracy: ±1.8ºF (±1ºC)
• Response time: 1 second
• Probe length: 5.125”
Includes: 1 “AAA” battery; wrist strap.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-PT300M
DIGITAL JUMBO DISPLAY SERVICE THERMOMETER
76.14
DiversiTech Jumbo Display Indoor/Outdoor Thermometer
For measuring and monitoring both indoor and outdoor temperature.
• Measures with water resistant outdoor probe
• Monitors outdoor temp. -58º to 158ºF
• Monitors indoor temp. 32º to 122ºF
• Large jumbo LCD display
• Recall of Min/Max
• 12 foot cable with probe
• Wall mount or stand for desktop display
• 12/24 hour clock
• Unit size: 4 x .75 x 4.5
Includes: 1 “AAA” battery; mounting accessories.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-DT898P
JUMBO DISPLAY INDOOR/OUTDOOR THERMOMETER
48.21
DiversiTech Standard Digital Panel Meter with External Sensor
Ideal for refrigeration applications.
• ºF/ºC switch
• High/low alarm
• Jumbo digital display
• 10 ft. cord with stainless steel sensor
• Probe size: 1.875”
• Resolution: 0.1º
• Digit height: 0.75”
• Display size: 1.85” x 0.85”
• Unit size: 2.4” x 1.4” x 0.5”
Includes: 1 “LR44” battery.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-DPM300PP
STANDARD DIGITAL PANEL METER WITH EXTERNAL SENSOR
58.21
423
Test Instruments
CONTROL MONITORS
Wagner Products Tattle-Tale
Control Monitor Identifies Open Controls In Seconds
Tattle-Tale is a single use monitoring device for determining which, if any, safety control has opened in response to a malfunction. It
saves many wasted hours tracing a safety control shutdown, even if it is intermittent. Here is a quick, inexpensive way to visually spot
exactly where the problem is. Simply install Tattle-Tale in parallel with each safety control. When a control opens, the attle-Tale’s red
indicator flag pops up. Use it to save hours of trouble shooting or install it before a problem arises, as part of your maintenance
program to immediately identify which area of the system is experiencing problems.
CAUTION: NOT TO BE USED WITH LOCKOUT RELAYS
Features:
• Disposable
• Inexpensive
• Totally safe
• Simple to use
• Pocket sized
Use For Monitoring:
• Safety controls
• Fuses
• Overload relays
• Motor protectors
• Freeze controls
• Limit controls
• Safety switches
• Fusible links
• Steam control
SOURCE 1 PART NO.
DESCRIPTION
MODEL NO.
STD. PACK
MLP $
S1-TT-120
S1-TT-24
S1-TT-240
120 VOLT AC OR DC
24 VOLT AC OR DC
MONITOR,CTRL,TATTLE-TALE,240V,PK OF 3
TT-120
TT-24
S1-TT-240
3
3
34.57
34.57
34.57
*Sold by Standard Pack / MLP per Standard Pack
DIAGNOSTIC DEVICES
GE TecMate ProTM
ECM Motor Module Diagnostic Tool
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-02642203000
MOTOR TESTER, GE TECMATE PRO
209.18
Pocket Tech ProTM Diagnostic Device
SOURCE 1 PART NO.
DESCRIPTION
VENDOR PART NO.
MLP $
S1-02642202000
POCKET TECH PRO DIAGNOSTIC DEVICE
PTP10012005
5485.71
LEAK TEST GAUGES
Air Test Gauge Assembly
• All parts precision made and assembled with sealant
• 3/4" FPT
• 2" Analog Gauge
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-PS-1427
PASCO AIR TEST GAUGE,2" DIA,3/4" FPT,0-30 PSI
15.68
424
Test Instruments
LEAK TEST GAUGES
DiversiTech Leak Test Gauge
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-TG-05
S1-TG-30
S1-TG-30-1
S1-TG-30-12
LEAK TEST GAUGE – 3/4” FPT., 5 PSI
LEAK TEST GAUGE – 3/4 FPT. CONN., 30 PSI
LEAK TEST GAUGE – 1” FPT. CONN., 30 PSI
LEAK TEST GAUGE – 1/2” FPT. CONN., 30 PSI
48.46
21.21
29.29
17.82
MULTIMETERS
DiversiTech Digital Multimeter with Bright Screen Display
Autoranging, Easy-to-Use, Easy-to-See.
• 10 Functions – 37 Ranges
• Manual and Autoranging
• High Impact Thermoplastic Case
• Simple Operation
• Safety Recessed Test Lead Connections
• Overload Protection on all Ranges
• Audible Continuity
• 10A AC/DC Range
• Data Hold
• Auto Power Off
• Ranges and Accuracy
AC Voltage: 0-200mV/2/20/200/600 VAC, ±1%
DC Voltage: 0-200mV/2/20/200/600 Vdc, ±0.5%
AC Current: 0-2mA/20m/200mA/10Aac,±1.5%
DC Current: 0-2mA/20m/200mA/10Adc, ±1.2%
• Resistance: 0-200/2k/20k/200k/2M/20Mø, ±1%
• Capacitance: 0-20n/200nF/2u/20u/100uF, ±3%
• Frequency: 1-20/200/2k/20k/200k/2MHz, ±0.2%
• Duty Cycle: 0.1 to 99.9%, ±1%
Includes: Test leads; 1 “9V” battery.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-DMM45
DIGITAL MULTIMETER WITH BRIGHT SCREEN DISPLAY
122.00
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-DMM20UL
DIGITAL UL LISTED MULTIMETER
48.21
DiversiTech Digital UL Listed Multimeter
DiversiTech Mini AC AMP Clamp Meter
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-DAMP221
MINI AC AMP CLAMP METER
227.89
425
Test Instruments
PH METERS & REFRIGERANT LEAK DETECTORS
DiversiTech High Performance Refrigerant Leak Detector with Pump
HVAC, Industrial, Automotive, small leaks.
• Microprocessor Control with advanced digital signal
• Alarm Method: Buzzer, Tricolor LED bar Indicator
processing
• Snake Tube length: 40cm (15.5”)
• Multi color visual display
• Dimension / Weight: 6.8”H x 2.6”W x 2.2”D (173 x
• High-median-Low leak sensitivity selector
66 x 56mm) approximately 14.1 oz (400g)
• Low battery indication
• Battery Life: Approx. 7 hours normal use
• Semiconductor gas sensor
• Auto power OFF: 10 minutes
• Detection of R-134a, R-404A, R-410A, R-407C, R22 Freon
• Disable Auto Power Off: Press and Hold “Hi” button
gas, etc.
then power on the meter
• Sensitivity (H/M/L): R-22, 134a 3g/year 15g/year 30g/year,
• Warm-Up Time: Approximately 45 seconds
R-404A, 407C, 410A 4g/year 20g/year 40g/year
• Altitude: < 2000M (6500’)
• 15.5” (40cm) flexible stainless probe
• Operating Temperature and Humidity: 32º to 104ºF
• Reference Leak source included
(0º to 40ºC), < 80% RH
• Ambient concentration reset
• Storage Temperature and Humidity: 14º to 140ºF
(-10º to 60ºC), < 70% RH
• Long-life, DC brushless fan
• Automatic zero and background compensation
Includes: 4 “AA” Alkaline batteries; leak check bottle; molded hard case.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-RLD382P
HIGH PERFORMANCE REFRIGERANT LEAK DETECTOR WITH PUMP
882.64
DiversiTech HVACR Refrigerant Leak Detector
Industrial and Automotive uses.
• Detects ALL halogenated refrigerants
• Sensitivity adjustment dial
• High sensitivity
Includes: 2 “C” batteries.
• Equipped with quality sensor
• Flexibility up to 3 gr/yr
• Microcomputer processor control
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-RLD202
HVACR REFRIGERANT LEAK DETECTOR
460.43
DiversiTech Pocket pH Meter
Ideal for cooling towers.
• Digital display
• Electrode extends to 3.15”
• Pocket sized
• pH range: 0.0 to 14.0 pH
• Automatic temperature compensation
• Size: 6.2” x 1.5” x 1.3”
• Lightweight
• Weight: 4 oz.
Includes: 1 “9V” battery; hard carrying case; calibration solution; calibration screwdriver.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-PH501
POCKET PH METER
161.89
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-TPK500
GENERAL PURPOSE BEADED TIP PROBE
42.32
PROBES
DiversiTech General Purpose Beaded Tip Probe
• Wire length: 3.125’
426
Test Instruments
PROBES
DiversiTech General Purpose K-Type Probe with Cord
• Probe length: 3.75”
• Cord length: 4’
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-TPK02
GENERAL PURPOSE K-TYPE PROBE WITH CORD
189.82
DiversiTech Piercing K-Type Probe with Cord
• Probe length: 8”
• Cord length: 4’
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-TPK05
PIERCING K-TYPE PROBE WITH CORD
153.36
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CT800
TEST LEADS - SET OF 10
16.57
DIVERSITECH TEST LEADS
DiversiTech Test Leads, 18"
Ten 18” Multi Color Test Leads
DiversiTech Test Leads, 22"
Low voltage test leads, eight 22in. long, color-coded leads with fully insulated alligator clips
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-5031
TEST LEADS - SET OF 8
17.11
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-FTL3
RED/BLACK TEST LEADS - 36"
15.21
DiversiTech Test Leads, Red/Black
• Pair of 36" test leads with insulated alligator clips
427
Test Instruments
TEST CORDS
DiversiTech Test Cord (Female)
•
•
•
•
•
•
•
•
•
Red and black heavy duty boots
Large clips
3 wire
Get power in remote areas without 110V outlet
Volts: 3 to 20V
Amps: 125
Wire gauge: 16 gauge
Length: 24”
Weight: 0.36 lb.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-CT700F
TEST CORD (FEMALE)
27.21
TESTERS
DiversiTech Audible/Visual Non-Contact Voltage Tester – UL Listed
Ideal for voltage breaks in lines.
• Non-Contact Voltage Detection
• Indicates presence of voltage from 50-600VAC
• Reads Hot Wire with Respect to Ground
• Audible and Visual Indication, Easy-to-use
• Voltage Range: 50-600VAC
• Frequency Range: 50-500 Hz
• Operating Environment: 32º to 122ºF (0º to 51ºC) at <95% RH
• Storage Temp.: -4 to 140ºF (-20 to 60ºC) at <95% RH
• Dimensions: 6.0” x .9” x .8” (152x23x20mm)
• Weight: 1.6 oz. (50g)
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-VS3000A
AUDIBLE/VISUAL NON-CONTACT VOLTAGE TESTER –UL LISTED
32.79
DiversiTech Bright Red LED Screwdriver Tester
Checks for Continuity, Voltage.
• Self-test, Continuity and polarity checks
• Microwave leakage test
• Checks fuse s
• Drop-resistant to 10 feet
• AC voltage: 70 to 250V
• Non-contact AC: 70 to 600V
• Continuity test: 0 to 50Mº Includes: 1 “LR44” battery
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-ST600LED
BRIGHT RED LED SCREWDRIVER TESTER
11.14
428
Tools
SAE CORE REMOVER/INSTALLER
CPS Products SAE Core Remover/Installer
1/4" SAE ball valve core remover/installer tools
Features:
•
•
•
•
Designed to remove and install valve core without losing system charge
Increases evacuation and charging speed by creating unrestricted access
Accessory items available for added service applications
800PSI working pressure
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CP-TLVC
S1-CP-TLVCS
TOOL,1/4" SAE CORE REMOVER/INSTALLER
TOOL,1/4" SAE CORE REMOVER/INSTALLER,SP
64.14
93.64
SCALES
DiversiTech Electronic Utility Scales
Constructed for heavy duty weighing. Perfect for warehouse use, check weighing, large crates and shipping freight. Low profile
platform. Control panel can be wall mounted for easy viewing. Large LCD display. Operates with AC adapter (included) or one 9V
battery (not included).
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-660-004
S1-660-005
150 LB. CAPACITY (PELOUZE #4010)
400 LB. CAPACITY (PELOUZE #4040)
558.11
647.07
DiversiTech Refrigerant Hanging Scale
Check-weigh gas cylinder contents when filling or recapturing. Know the exact gas weight! Dial adjusts for tare weight. Dual dial
markings run clockwise and counter clockwise. Lightweight. Scale goes wherever the serviceman goes! Suspension accessory
included.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-660-001
HANGING SCALE – PELOUZE #D70
225.64
DiversiTech Utility Scales
Large easy to read dial can be viewed from top or side. Low profile enables you to slide cartons and crates onto scale. Memory Lock
holds reading when dial is obscured. Perfect for shipping and receiving parcels or crates in the mailroom or warehouse.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-660-002
S1-660-003
100 LB. CAPACITY (PELOUZE #P100S)
250 LB. CAPACITY (PELOUZE #P250S)
364.50
386.54
429
Tools
CARRYING STRAP
Refrigerant Cylinder Carrying Strap
JugLugger Refrigerant Cylinder Carrying Strap
The JugLugger® refrigerant strap quickly connects to refrigerant cylinders and frees technicians' hands to carry
tools and climb ladders improving safety. Service calls can be reduced by as much as 10 minutes resulting in
increased productivity. OSHA 1926.1053 on ladder safety, requires the use of two hands when climbing ladders;
since 2007, thousands of HVACR technicians have started using a JugLugger refrigerant strap to move
refrigerant from their service trucks and vans to job sites.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-JL1
JUGLUGGER,REFRIGERANT CYL CARRYING STRAP
81.25
COMPRESSOR TOTES
Wagner Products Compressor Tote
Makes Light Work Of A Heav y Job
Electroplated, strong steel construction-practically indestructible.
Recommended for use with all compressors up to 5 tons. Will even handle new high efficiency compressors.
An indispensable tool for every serviceman.
Features:
• Pick a compressor from its box
• Carry a compressor up a ladder
SOURCE 1 PART NO.
DESCRIPTION
MODEL NO.
MLP $
S1-ACT-6
COMPRESSOR TOTE
ACT-6
79.18
SOURCE 1 PART NO.
DESCRIPTION
ORDER MULTIPLE
MLP $
S1-HS-30
S1-HS-60
HANGING STRAP - 31"
HANGING STRAP - 60"
24
24
5.64
7.93
SOURCE 1 PART NO.
DESCRIPTION
ORDER MULTIPLE
MLP $
S1-HS-144
LASHING STRAP - 12 FOOT
6
54.86
SOURCE 1 PART NO.
DESCRIPTION
ORDER MULTIPLE
MLP $
S1-HS-192
RATCHET STRAP - 16 FOOT
3
77.14
STRAP
Hanging Straps
Lashing Strap - 12 Foot
Ratchet Strap - 16 Foot
430
Tools
STRAP
Rubber Tie-Down Straps
SOURCE 1 PART NO.
DESCRIPTION
ORDER MULTIPLE
MLP $
S1-RS-15
S1-RS-20
S1-RS-31
S1-RS-41
RUBBER TIE DOWN STRAP, 15"
10
10
10
10
2.54
3.21
3.61
4.89
CLEANING BRUSHES
Carbon Steel Curved Handle Scratch Brush
Used for general purpose cleaning.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-B-10
CARBON STEEL CURVED HANDLE SCRATCH BRUSH
8.21
DiversiTech Chip Brushes
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-B-500
S1-B-501
S1-B-502
S1-B-503
S1-B-504
S1-B-505
CHIP BRUSH – 1/2”
CHIP BRUSH – 1”
CHIP BRUSH – 1-1/2”
CHIP BRUSH – 2”
CHIP BRUSH – 2-1/2”
CHIP BRUSH – 3”
36
36
36
24
12
12
1.04
1.18
1.43
1.68
2.25
2.64
*Sold by Standard Pack / MLP per each.
DiversiTech Condenser/Heat Exchanger Brushes
Ideal for cleaning mineral deposits from inside metal tubes. Especially recommended for use with power tools, although handle for
manual use is available.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-B-602
S1-B-604
S1-B-607
S1-B-610
S1-B-613
S1-B-616
S1-B-619
S1-B-622
S1-B-628
S1-B-633
S1-B-702
S1-B-704
S1-B-707
S1-B-710
S1-B-713
S1-B-716
CONDENSER/HEAT EXCHANGER BRUSH – 1/4” BRASS 8-32 FEMALE
CONDENSER/HEAT EXCHANGER BRUSH – 1” BRASS 12-24 FEMALE
CONDENSER/HEAT EXCHANGER BRUSH – 1/4” NYLON 8-32 FEMALE
13.21
14.21
14.64
14.18
14.93
14.14
14.93
14.93
14.93
15.39
8.46
8.71
8.71
8.71
8.93
8.93
S1-B-719
S1-B-722
S1-B-728
S1-B-733
S1-B-802
S1-B-804
S1-B-807
S1-B-810
S1-B-813
S1-B-816
S1-B-819
S1-B-822
S1-B-828
S1-B-833
CONDENSER/HEAT EXCHANGER BRUSH – 1” NYLON 12-24 FEMALE
CONDENSER/HEAT EXCHANGER BRUSH – 1/4” STAINLESS 8-32 FEMALE
CONDENSER/HEAT EXCHANGER BRUSH – 1” STAINLESS 12-24 FEMALE
8.93
9.21
9.50
9.43
17.43
21.32
20.39
22.71
20.86
21.11
21.39
21.82
20.86
21.07
431
Tools
CLEANING BRUSHES
DiversiTech Condenser/Heat Exchanger Brushes for Commercial Tube Cleaning
For all commercial power tube cleaning machines. 1/4” and 3/8” dia. brushes have 8-32 female threads. 7/16”–1” brushes have 1/4–
28 male threads. Use 7/16”–1” brushes for both CW and CCW rotation using a 1/4–28 NF jam locknut.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-B-202
S1-B-204
S1-B-207
S1-B-210
S1-B-213
S1-B-216
S1-B-219
S1-B-222
S1-B-228
S1-B-233
S1-B-302
S1-B-304
S1-B-307
S1-B-310
S1-B-313
S1-B-316
S1-B-319
S1-B-322
S1-B-328
S1-B-333
S1-B-402
S1-B-404
S1-B-407
S1-B-410
S1-B-413
S1-B-416
S1-B-419
S1-B-422
S1-B-428
S1-B-433
CONDENSER/HEAT EXCHANGER BRUSH – 7/16” BRASS 1/4-28 MALE
CONDENSER/HEAT EXCHANGER BRUSH – 1” BRASS 1/4-28 MALE
CONDENSER/HEAT EXCHANGER BRUSH – 7/16” NYLON 1/4-28 MALE
CONDENSER/HEAT EXCHANGER BRUSH – 1” NYLON 1/4-28 MALE
CONDENSER/HEAT EXCHANGER BRUSH – 7/16” STAINLESS 1/4-28 MALE
CONDENSER/HEAT EXCHANGER BRUSH – 1” STAINLESS 1/4-28 MALE
11.89
11.89
11.89
11.89
11.89
11.89
12.71
12.71
12.71
12.71
7.21
7.54
7.21
8.21
8.21
8.21
8.21
9.21
9.21
9.21
12.39
12.39
13.18
12.39
12.39
13.18
11.29
13.93
13.93
13.93
DiversiTech Duct Cleaning Brush
Black fiber bristles twisted in wire. 2-1/8” dia. x 7” Brush x 48” overall length.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-542-76220
DUCT CLEANING BRUSH
12.14
DESCRIPTION
MLP $
DiversiTech Extension Rods for Condenser Tube Brushes
Aluminum rods thread into each other to make an endless length.
SOURCE 1 PART NO.
S1-BE-24
S1-BE-36
S1-BE-48
S1-BH-1
STD.
PACK
24” RODS WITH MALE THREAD ONE END, FEMALE OTHER 12-24 THREAD
3
SIZE
36” RODS WITH MALE THREAD ONE END, FEMALE OTHER 12-24 THREAD
3
SIZE
48” RODS FOR 1/4” BRUSHES ONLY 8-32 THREAD SIZE
3
HANDGRIP – 4” LONG THREADS INTO RODS
1
*Sol d by Standard Pack / M LP per each.
432
17.89
20.39
10.96
9.43
Tools
CLEANING BRUSHES
DiversiTech Outside Tube Cleaning Brushes
Tough molded plastic holder with comfortable sure grip design and high carbon steel bristles.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-542-00966
S1-542-00968
OUTSIDE TUBE CLEANING BRUSH – 1/2” ID (5/8” OD)
OUTSIDE TUBE CLEANING BRUSH – 3/4” ID (7/8” OD)
6
6
7.21
8.57
DiversiTech Parts Cleaning Brush
Heavy duty black polypropylene bristles in strong plastic handle.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-542-25015
PARTS CLEANING BRUSH
12
11.86
DiversiTech Refrigerator Coil Brush
Clean refrigerator coils, fan blades and areas under and behind appliances. 27-1/2” in length with 11-3/4” brush length. Bristles are
3/4” on the end tapering to 1-1/2” toward the handle.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-B-27
REFRIGERATOR COIL BRUSH
12.39
DiversiTech Welder’s Brush
Stainless steel bristles used for cleaning all metals. Great for cleaning aluminum prior to soldering.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-B-4
WELDER’S BRUSH
12
5.75
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-542-10007
WOOD HANDLE DOPE BRUSH – 3/4” x 7”
36
3.11
*Sold by S tandard Pack / MLP per each.
DiversiTech Wood Handle Dope Brush
Select horsehair bristles secured tightly in metal ferrule.
COPPER TUBE CLEANING BRUSHES & ACID BRUSHES
DiversiTech 2-in-1 Copper Tube Cleaning Brush
Easy to hold combination tool that really works. One end cleans the fitting. T he other cleans the tube.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-B-996
S1-B-998
2-IN-1 COPPER TUBE CLEANING BRUSH – 1/2” ID (5/8” OD)
2-IN-1 COPPER TUBE CLEANING BRUSH – 3/4” ID (7/8” OD)
27.07
27.07
433
Tools
COPPER TUBE CLEANING BRUSHES & ACID BRUSHES
DiversiTech Copper Tube Fitting Brushes
Highest quality brushes to clean fittings faster, easier and more safely. Made with strong, resilient, rustproof stainless steel bristles
secured in a 4-ply wire with easy-to-grip plastic handle. Economy models feature same quality stainless steel, but secured in 2-ply
wire.
SOURCE 1 PART NO.
S1-B-124
S1-B-125
S1-B-126
S1-B-127
S1-B-128
S1-B-129
S1-B-130
S1-B-131
S1-B-132
S1-B-924
S1-B-925
S1-B-926
S1-B-927
S1-B-928
S1-B-929
S1-B-930
S1-B-931
S1-B-932
S1-B-934
S1-B-935
DESCRIPTION
STD.
PACK
COPPER TUBE FITTING BRUSH – ECONOMY 1/4” O.D., 9/32” BRUSH DIA.
1
6
6
6
6
6
COPPER TUBE FITTING BRUSH – ECONOMY 1” O.D., 1-1/8” BRUSH DIA.
6
COPPER TUBE FITTING BRUSH – ECONOMY 1-1/8” O.D., 1-1/4” BRUSH DIA. 6
COPPER TUBE FITTING BRUSH – ECONOMY 1-3/8” O.D., 1-1/2” BRUSH DIA. 6
COPPER TUBE FITTING BRUSH – 1/4” O.D., 9/32” BRUSH DIA.
1
1
COPPER TUBE FITTING BRUSH – 1” O.D., 1-1/8” BRUSH DIA.
COPPER TUBE FITTING BRUSH – 1-1/8” O.D., 1-1/4” BRUSH DIA.
1
1
1
1
1
1
1
1
1
MLP $
4.54
4.54
4.75
4.75
5.00
5.04
5.79
5.50
6.18
9.71
9.71
9.71
9.71
9.93
9.93
10.21
10.21
10.75
10.75
11.71
DiversiTech Tin Handle Acid Brushes
Manufactured with electrolyte tin plate and filled with 100% pure stiff horsehair, tied with a steel staple. T his combination gives lasting
qualities when used with heat and acids or other cleaning agents.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-B-1GROSS
S1-B-2
TIN HANDLE ACID BRUSH 3/8”, 1 GROSS (144 PCS.)
TIN HANDLE ACID BRUSH 1/2”, 1 GROSS (144 PCS.)
29.57
38.50
*M LP per gross of 144 pieces
DIAGONAL CUTTERS
DiversiTech Oval Head Diagonal Cutter
• For cutting soft wire and other light materials. For an accurate cut in tight areas.
• Overall jaw length - 1/2” (13mm).
• Overall length - 4-1/4” (108mm).
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-T906
OVAL HEAD DIAGONAL CUTTER
11.18
DIVERSITECH NUT SETTERS - HEX DRIVE
SOURCE 1 PART NO.
DESCRIPTION
SHIPPING MULTIPLE
MLP $
S1-5-MSH1/4MC
S1-5-MSH5/16MC
1/4" NUT SETTER, 1-PK
5/16" NUT SETTER, 1-PK
30
30
5.64
6.07
434
Tools
FIN TOOLS
DiversiTech Fin Whisk
A plastic handled whisk for cleaning condenser and evaporator fins.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-B-26
FIN WHISK BRUSH
12
3.14
*Sold by S tandard Pack / MLP per each.
DiversiTech Multi-Head Fin-Tool
Conveniently straightens and cleans condenser and evaporator fins. Each nylon head slides into the master
handle and tightens in place. Heads are designed to fit units with fin spacing of 4–24 fins per inch. Each head is
engraved with its own size and is color coded for fast identification. Heads are angled so that when inserted in
the handle, the hand is a safe distance from the sharp fins. Heads may also be reversed in the handle so that
combing with an upward stroke recommended method) may be done easily with proper leverage. The master
handle rests comfortably in a man-size grip, is rigid, and long lasting. U.S. Patent No. 4,018,076.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-T-1
S1-T-10
S1-T-100
S1-T-101
S1-T-11
S1-T-12
S1-T-13
S1-T-14
S1-T-15
S1-T-16
S1-T-17
S1-T-18
S1-T-20
S1-T-21
S1-T-23
S1-T-8
S1-T-9
HANDLE ONLY – BLACK
HEAD 10 FPI – NATURAL
KIT – 1 HANDLE AND 6 HEADS: 8, 9, 10, 11, 12, 14
KIT – 1 HANDLE AND 6 HEADS: 13, 15, 16, 17, 18, 20
HEAD 11 FPI – BLUE
HEAD 12 FPI – GREEN
HEAD 13 FPI – PINK
HEAD 14 FPI – LT. GREEN
HEAD 15 FPI – AQUA
HEAD 16 FPI – BROWN
HEAD 17 FPI – BLUE
HEAD 18 FPI – RED
HEAD 20 FPI – PURPLE
HEAD 21 & 22 FPI – ROSE (FOR CARRIER UNIT)
HEAD 23 & 24 FPI – BLACK (FOR CARRIER UNIT)
HEAD 8 FPI – ORANGE
HEAD 9 FPI – YELLOW
1
3
12
12
3
3
3
3
3
3
3
3
3
3
3
3
3
4.07
9.39
17.39
17.39
9.39
9.39
9.39
9.39
9.39
9.39
9.39
9.39
9.39
9.39
9.39
9.39
9.39
DiversiTech SuperComb
Easier to grip, easier to use tool for straightening condenser and evaporator fins. Straightens 50% more fins in
one stroke. Keeps hands a safe distance from fins. Easy to grip, strong, durable, heavy duty nylon. Color coded
for easy identification. Sold individually or in a set of 6. Sales display available
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-T-400
SET OF 6 – 1 EACH: T-408, T-409, T-411, T-410, T-417,
T-418
9 AND 15 FPI – YELLOW
11 AND 13 FPI – BLUE
12 AND 14 FPI – GREEN
16 AND 17 FPI – LIME
18 AND 20 FPI – RED
1
30.86
6
6
6
6
6
5.96
5.96
5.96
5.96
5.96
S1-T-409
S1-T-411
S1-T-412
S1-T-417
S1-T-418
*Sold by S tandard Pack / MLP per each. **M LP per set.
435
Tools
FIN TOOLS
DiversiTech Swivel Head Deburring Tool
• Professional quality and performance of higher price deburring tools.
• Two interchangeable blades.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-T482
S1-6-T482A
HANDLE LENGTH: 5-1/8” (130MM)
BLADE FOR STEEL, COPPER, ALUMINUM AND PLASTIC
33.61
7.39
Fin-Tool
Long lasting metal fin straightener. Straightens and cleans condenser and evaporator fins. One tool for all units.
The heavy duty spring wire bristles automatically adjust to ALL fin spacings. An exclusive tension adjustment
band is featured to
allow maximum rigidity and ease of operation. Straightens most severely damaged fins.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-T-200
S1-T-300
FIN-TOOL
FIN-TOOL WITH HEAVY DUTY BICYCLE HANDLE
1
12
20.57
17.75
*Sold by Standard Pack / M LP per each.
DRILL BITS
15-pc Black Oxide Drill Bit Set
Features:
• Durable rubber-sided case for added impact resistance
• Sliding latch design provides added security
• 135-degree split point prevents "walking"
• Black oxide coating resists corrosion
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-314015
15-PC BLACK OXIDE BIT SET
53.96
Lenox Bimetal Utility Bits
High Speed steel cutting edge provides longer life in tough applications such as nail-embedded wood. The 3 sharp cutting edges
allow for a fast chip removal and a clean hole in the material. Cutting Edges can be resharpened using a diamond file.
SOURCE 1 PART NO.
DESCRIPTION
PRODUCT APPLICATION
MLP $
S1-1094906A1416
S1-1095106A1816
S1-1095306A2216
S1-10955500K
BI-METAL UTILITY BITS-06A1416 6 x 7/8
BI-METAL UTILITY BITS-06A1816 6 x 1-1/8
BI-METAL UTILITY BITS-06A2216 6 x 1-3/8
KITS-500K 5 PIECE UTILTY BIT KIT-500K
DRILLING HOLES IN WOOD
42.79
61.39
79.18
251.86
Lenox Vari-bit Step Drills
Patented two flute design provides for fast clean holes in m etal. Split point design for faster penetration and reduced walking.
Patented flute design allows for fast chip removal.
SOURCE 1 PART NO.
DESCRIPTION
PRODUCT APPLICATION
MLP $
S1-30881VB1
S1-30882VB2
S1-30883VB3
S1-30887VB7
S1-30888VB11
S1-30912VB12
1/8" - 1/2" (VB1)
1/2" - 1" (VB2)
1/4" - 3/4" (VB3)
1" - 7/8" (VB7)
7/8" - 1-1/8" (VB11)
7/8" - 1-3/8" (VB12)
DRILLING HOLES IN METAL
80.64
140.46
123.14
139.07
188.54
215.57
436
Tools
HACKSAWS
DiversiTech Deluxe Hi-Tension Hacksaw
Hackframe featuring handle and end pieces made of die cast aluminum. Lightweight yet rigid and highly tensioned (up to 25,000 psi)
for cleaner, surer cut. Permanent blade pins feature versatile angling (up to 55°) for flush cutting. Blade can be inserted in handle to
be used as compass saw. Frame will fit most standard tool boxes
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-540-278BM0024
S1-540-278HX0002
REPLACEMENT BLADES FOR HACKSAW FRAME 12” x 24T
HACKSAW FRAME WITH BLADE
3.64
42.29
Lenox Bi-metal Hack Saw Blades and Frames
T he Lenox HT 50 Hacksaw Frame allows for up to 50,000 psi for straight cuts and stores up to 5 blades. All Lenox hacksaw frames
come with T2 technology hacksaw blades that last up to 2 times longer than standard hacksaw blades.
SOURCE 1 PART NO.
S1-12132HT50
S1-20144V218HE
S1-20145V224HE
S1-20146V232HE
S1-20997TFHS618636
DESCRIPTION
PRODUCT APPLICATION
MLP $
HACKSAW FRAME (HT50)
12" x 18 TPI 10 PK (V218HE)
12" x 24 TPI 10 PK (V224HE)
CUTTING METAL/PVC
CUTTING MEDIUM METAL/PVC
CUTTING THIN METAL/PVC
79.21
4.64
4.64
12" x 32 TPI 10 PK (V232HE)
TRI-FOLD SAWS-618636
CUTTING THIN METAL/PVC
CUTTING DRYWALL AND WOOD
4.64
64.43
HOLE CUTTERS
Lenox Carbide Hole Cutters
Precision ground carbide teeth for fast clean, round holes. Over-drill stopper prevents the cutter from crashing through hole. Split point
pilot drill allows for quick penetration with out walking.
SOURCE 1 PART NO.
DESCRIPTION
PRODUCT APPLICATION
MLP $
S1-2009314CHC
S1-2009618CHC
S1-2010022CHC
S1-3087935PD
S1-308803CHCAS
7/8" (14CHC)
1-1/8" (18CHC)
1-3/8" (22CHC)
PILOT DRILL (35PD)
PLUG EJECTION SPRINGS (3CHC-AS)
CUTTING HOLES IN METAL
ACCESSORY FOR CARBIDE HOLE CUTTERS
ACCESSORY FOR CARBIDE HOLE CUTTERS
72.36
79.04
88.93
11.11
2.57
HOLE SAWS AND ACCESSORIES
Lenox Hole Saws and Accessories
Lenox Bi-Metal Hole Saws are built to cut through metal and wood. The patented T uff Tooth and Vari-T ooth designs are built to cut
stronger, last longer and resist tooth strippage. T hick backing plates also resist breakage in high torque applications.
SOURCE 1 PART NO.
DESCRIPTION
PRODUCT APPLICATION
MLP $
S1-300022L
S1-300055L
S1-300066L
ARBOR (2L)
ARBOR (5L)
ARBOR (6L)
HOLE SAW ACCESSORY
HOLE SAW ACCESSORY
HOLE SAW ACCESSORY
48.71
31.14
47.43
S1-3001010L
S1-3001414L
S1-3001818L
S1-3002222L
S1-3002626L
S1-3003232L
S1-3003434L
S1-3004040L
S1-3004848L
S1-3006666L
S1-30830600R
S1-308504321
S1-3085156PD
S1-30925VBX8
5/8" (10L)
7/8" (14L)
1-1/8" (18L)
1-3/8" (22L)
1-5/8" (26L)
2" (32L)
2-1/8" (34L)
2-1/2" (40L)
3" (48L)
4-1/8" (66L)
9 PIECE KIT (600R)
PILOT DRILL 1 PK (4321)
PILOT DRILL 1 PK (56PD)
8" EXTENSION (VBX8)
CUTTING HOLES IN METAL AND WOOD
HOLE SAW ACCESSORY
HOLE SAW ACCESSORY
HOLE SAW ACCESSORY
23.18
23.18
25.07
26.43
26.43
33.21
40.07
43.18
44.71
73.36
273.36
10.46
11.79
50.75
RECIPROCATING SAW BLADES
DiversiTech Reciprocating Saw Blades
• 6" x 6T Wood and Nail Slope 3/4" x 6" x 0.05"
SOURCE 1 PART NO.
DESCRIPTION
SHIPPING MULTIPLE
MLP $
S1-540-RB636W
RECIPROCATING SAW BLADES, 6" x 6T
5
6.79
437
Tools
RECIPROCATING SAW BLADES
Lenox Gold Reciprocating Saw Blades
Lenox Gold Reciprocating Saw Blades give the user up to 3x longer life in all reciprocating saw blade applications. The patented
titanium coated design allows the blade to cutter faster and cooler than non-coated blades. T2 patented technology provides efficient
cutting for specific applications.
SOURCE 1 PART NO.
S1-21060656GR
S1-21062956GR
S1-21067614GR
S1-21069618GR
S1-21070818GR
S1-21072624GR
DESCRIPTION
PRODUCT APPLICATION
MLP $
6" x 6TPI (656G) 5 PK
9" x 6TPI (956G) 5 PK
6" x 14TPI (614G) 5 PK
6" x 18TPI (618G) 5 PK
8" x 18TPI (818GR) 5 PK
6" x 24TPI (624G) 5 PK
CUTTING NAIL-EMBEDDED WOOD
CUTTING MEDIUM METAL
CUTTING THIN METAL
9.50
12.54
8.00
8.00
10.07
8.00
Lenox Reciprocating Saw Blades
Lenox Bi-Metal Reciprocating Saw Blades give the user up to 100% longer life and cut 2 time faster in all reciprocating saw blade
applications. T2 patented technology provides efficient cutting for specific applications. Lenox T 2 Bi-metal design provides durability
and flexibility that single metal blades can't.
SOURCE 1 PART NO.
S1-12129635R
S1-12130835R
S1-20530B656R
S1-20562610R
S1-20564614R
S1-20566618R
S1-20568624R
S1-20570636RP
S1-20572656R
S1-20576800RG
S1-20578818R
S1-20580810R
S1-20582956R
S1-20583110R
S1-20585156R
DESCRIPTION
PRODUCT APPLICATION
MLP $
6" x 10/14TPI (635R) 5 PK
8" x 10/14TPI (835R) 5 PK
6" x 6TPI (B656R) 25 PK
6" x 10TPI (610R) 5 PK
6" x 14TPI (614R) 5 PK
6" x 18TPI (618R) 5 PK
6" x 24TPI (624R) 5 PK
6" x 6TPI (636RP) 5 PK
6" x 6TPI (656R) 5 PK
8" x Grit (800RG) 2 PK
8" x 18TPI (818R) 5 PK
8" x 10TPI (810R) 5 PK
9" x 6TPI (956R) 5 PK
12" x 10/14TPI (110R) 5 PK
12" x 6TPI (156R) 5 PK
CUTTING WOOD AND THICK METAL
CUTTING WOOD AND MEDIUM METAL
CUTTING THIN METAL
GENERAL PURPOSE CUTTING
CUTTING CAST IRON PIPE
CUTTING WOOD AND THICK METAL
7.39
70.86
7.57
6.64
7.07
6.64
6.64
7.89
7.89
18.57
8.39
8.39
10.46
12.79
12.79
HOSES, WATER NOZZLES & MEASURING TAPES
DiversiTech Garden Hose
High quality product priced for high volume sales.Soft-Flex formulation makes the 5 ply Hose easy to handle.
Withstands 500 psi water pressure. Heavy duty solid brass couplings and collar. Full Lifetime Guarantee!
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-5-IG5850
GREEN FLEXON 5-PLY FOREVER GARDEN HOSE
5
69.71
*Sold by Standard Pack / ML P per each.
438
Tools
HOSES, WATER NOZZLES & MEASURING TAPES
DiversiTech Hot Water Hose
High burst strength. 500 psi. Withstands hot water up to 160°F. EPDM tube. Heavy duty solid brass couplings.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-5-HW5850
5/8” x 50’ HOT WATER HOSE
5
114.04
DiversiTech Pistol Grips & Water Nozzle
Pistol Grip – 572 Insulated: For spraying hot or cold water. Heavy-duty, self-adjusting “duck” packing for lifetime
proof seal.
Water Nozzle – 573 Un-insulated: Heavy-duty and holds open clip for continuous spraying. Self-adjusting “duck”
for leak proof seal.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-540-572
S1-540-573
INSULATED PISTOL GRIP
UNINSULATED WATER NOZZLE
12/CASE
12/CASE
37.39
20.21
DiversiTech Power Measuring Tapes
Rust resistant yellow lacquered blade with easy to read inch/foot markings (English). Both chrome and neon
case have belt clips and finger-tip blade lock. Ultralife tape is our highest quality tape measure — lasts up to 10
times longer than typical blades, with patented “blade wiper” that cleans the blade as you measure.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-540-12
S1-540-25G
S1-540-25R
POWER TAPE – CHROME 1/2” x 12’
POWER TAPE – NEON GREEN 1” x 25’
POWER TAPE – NEON ORANGE 1” x 25’
6
6
6
23.50
37.82
37.82
439
Tools
HOSE CLAMPS, INSPECTION MIRRORS & SCREW STARTERS
DiversiTech Hose Clamps
Partial stainless, worm drive, adjustable. 300 series stainless steel 1/2” band with plated 5/16” slotted hex head screw and housing,
except the B-4H which has a 5/16” band and 1/4” nut. Recommended for most applications. 100% interlock construction features onepiece housing which directly locks into band. Spot weld free design.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-B-10H
S1-B-12H
S1-B-16H
S1-B-20H
S1-B-24H
S1-B-28H
S1-B-32H
S1-B-36H
S1-B-4H
S1-B-6H
S1-B-8H
S1-HC5410
NO. 10, 9/16” – 1-1/16” DIAMETER, 3/8” – 5/8” HOSE I.D.
NO. 12, 9/16” – 1-1/4” DIAMETER, 5/8” – 3/4” HOSE I.D.
NO. 16, 11/16” – 1-1/2” DIAMETER, 3/4” – 1” HOSE I.D.
NO. 20, 3/4” – 1-3/4” DIAMETER, 1” – 1-1/4” HOSE I.D.
NO. 24, 1-1/16” – 2” DIAMETER, 1-1/4” – 1-1/2” HOSE I.D.
NO. 28, 1-5/16” – 2-1/4” DIAMETER, 1-1/4” – 1-3/4” HOSE I.D.
NO. 32, 1-9/16” – 2-1/2” DIAMETER, 1-1/2” – 2” HOSE I.D.
NO. 36, 1-13/16” – 2-3/4” DIAMETER, 1-3/4” – 2-1/4” HOSE I.D.
NO. 4, 7/32” – 5/8” DIAMETER, 3/16” – 5/16” HOSE I.D.
NO. 6, 3/8” – 7/8” DIAMETER, 1/4” – 3/8” HOSE I.D.
NO. 8, 7/16” – 1” DIAMETER, 5/16” – 1/2” HOSE I.D.
SAE NO. 10, SAE DIAMETER RANGE (IN)- .56 - 1.06, APPROX.
RANGE (IN) 9/16 - 1-1/8
10
10
10
10
10
10
10
10
10
10
10
6
1.18
1.32
1.32
1.57
1.32
1.32
1.32
1.32
1.18
1.18
1.18
10.57
DiversiTech Mechanical Screw Starter
A simple, easy way to end fumbling with hard to position screws. Ju st insert the screw on the prongs of the screw starter, and a simple
twist will lock the screw ready for trouble free starting. Tool automatically releases and resets. Use with ferrous or non-ferrous screws.
Nylon handle.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-S-3
ONE END SLOTTED, PHILLIPS ON OTHER, 9-1/4”
17.39
DiversiTech Telescopic Inspection Mirror
Fast, accurate visual inspection of hidden areas with an almost limitless number of positions. Double ball joint
links swivel mirrors for viewing to 360°. Precision engineered links are made from tempered spring steel to
withstand the stresse s of constant repositioning. Moves freely, holds desired position.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-M-1
S1-M-1R
S1-M-2
S1-M-2R
S1-M-3
MIRROR – 1-1/4” CIRCULAR – EXTENDS 6-1/4” TO 18-1/4”
REPLACEMENT HEAD FOR M-1
MIRROR – 2-1/4” CIRCULAR – EXTENDS 10” TO 14”
MIRROR – 2-1/8” x 3-1/2” RECTANGULAR – EXTENDS
11-1/4” TO 15-1/4”
REFILL MIRRORS ONLY 2-1/8” x 3-1/2”
MIRROR – 7/8” CIRCULAR – EXTENDS 6-1/2”
MIRROR – 1” x 2” OVAL – EXTENDS 8-1/2”
REFILL MIRRORS ONLY OVAL 1’ x 2”
1
1
1
1
1
14.57
6.29
16.79
7.29
16.79
12
1
1
1
1
12
1
2.86
7.29
11.36
5.46
11.36
2.04
6.29
S1-M-3G
S1-M-3R
S1-M-4
S1-M-4R
S1-M-5
S1-M-5G
S1-M-5R
440
Tools
PICKUPS & RETRIEVING TOOLS
DiversiTech Magnetic Retrieving Tool
Extra high flux magnet for greater pickup. Super adjustable telescoping action. Bright chrome plated brass handle. Powerful magnet
that will outperform the standard Alinco V Magnet 4 to 1. With the telescoping handle, you can pick up ferrous objects where your
hand cannot reach. When closed, it fits neatly in your pocket for easy accessibility.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-540-601
TOOL – POCKET TELESCOPIC EXTENDS FROM 5-7/8”(12CM) TO 25-9/16”(63CM)
– CARDED
12
12.46
*S ol d by Standard Pack / M LP per each.
DiversiTech Mechanical Pickup
•
•
•
•
•
Strong four prong steel jaws retrieve small items from hard-to-reach places.
Smooth actuator for greater control.
Chrome finish to prevent rust.
Flexible shaft to avoid obstacles.
24” (610mm) long
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-T396
4-PRONG STEEL JAWS; CHROME FINISHED WITH FLEXIBLE SHAFT
17.93
DiversiTech Reach-It
Retracts to 5” long. Made of durable chrome plated brass. Match can be quickly inserted.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-R-1
REACH-IT – EXTENDS TO 26-3/4”
12
8.82
*S ol d by Standard Pack / M LP per each.
DiversiTech Telescoping Mini-Light & Magnetic Pickup
•
•
•
•
•
•
•
A powerful permanent magnetic pick-up tool.
Ideal for retrieving steel and iron parts from hard-to-reach and see work areas.
Magnet is fitted in a 5-1/2” (140mm) long ergonomically designed handle.
4 Alkaline, “LR41”, batteries with a battery life of 48 continuous hours.
Light Bulb has a life of 100,000 hours of continuous use.
Mini-Light is fastened to a chrome plated brass wand with a double ball joint.
Ball and socket feature for simple, positive adjustments.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-T21
TELESCOPING MINI-LIGHT AND MAGNETIC PICKUP
68.46
DiversiTech Telescoping Mini-Light and Magnetic Pickup Combo
SOURCE 1 PART NO.
DESCRIPTION
CASE QTY
MLP $
S1-6-T582
TELESCOPING MINI-LIGHT AND MAGNETIC PICKUP
3
36.50
441
Tools
HVAC TOOLS
CPS Products Hex Key Adapter
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CP-TLSWAD
TOOL,HEX KEY ADAPTER
23.36
CPS Products R-410A Clutch Driven Flaring Tool
R-410A Clutch driven flaring tool with ratchet and case for 3/16", 1/4", 5/16", 3/8", 1/2", 5/8" & 3/4" O.D. tubing.
Features:
• Engineered to create stronger flare joints for high pressure R-410A systems
• Unique clutch driven feed screw and faceted cone produce uniform, clean flare walls without thin spots or
galling
• Provides an exact amount of flaring torque with breakaway clutch system
• Innovative 3/8" square drive incorporated directly in yoke handle for use of ratchet
• Rugged polyethylene storage case included
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CP- FT800FN
TOOL,FLARING,ADJ,R-410A CLUTCH DRIVEN
252.58
CPS Products R-410A Ductless Mini-Split Tool Kit
R-410A Ductless mini-split tool kit with Triple-Seal™ 2 valve manifold and SAE torque wrench
Features:
• Kit includes essential tools for install/service of ductless mini-split a/c units with
5/16" (1/2"-2o UNF) fittings
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CP-TLB410SAE
KIT,DUCTLESS MINISPLIT,R-410A SVC
873.00
CPS Products Solenoid Valve Troubleshooting Magnet, 18mm
Solenoid Valve T roubleshooting Magnet, 18mm
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CP-TLMKC18
TOOL,SOLENOID VALVE,TRBL SHT MAGNET,18MM
65.50
442
Tools
HVAC TOOLS
CPS Products Universal Ratcheting Tube Bender
Universal Ratcheting Tube Bender
Features:
• Universal kit bends tube from 1/4" to 7/8" (6 to 22mm)
• Metal ratcheting system built for long life
• Durable mandrel
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CP-TB250
TOOL,TUBE BENDER,UNVL RATCHET 3/8"-7/8"
382.96
Midwest® HVAC Tools
Hot drop-forged carbon steel blades. Com pound l everage action handles. Heavy duty plasti c grips.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-540-FCTMC5
S1-540-FCTMN1
S1-540-FCTMS1
S1-540-FCTMS2
8” CRIMPER – 22 GA. CRIMPING CAPACITY
8” NOTCHER – 31° CUTTING ANGLE
3” STRAIGHT SEAMER – 22 GA. CAPACITY
3” OFFSET SEAMER – 22 GA. CAPACITY
3
3
2
2
73.96
104.07
111.82
119.18
LENOX ALUMINUM PIPE WRENCHES
Lenox pipe wrenches hardened teeth are ideal for most hard pipes and fittings. T he durable I-beam design can withstand high torque
will providing the lightweight and ergonomical feel need for repetitive use.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-2382214ALPW
S1-2382318ALPW
ALUMINUM PIPEWRENCH 14"
ALUMINUM PIPE WRENCH 18"
130.00
163.25
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-RT70021
S1-RT70105
CUTTER,TUBE,1/4" TO 1-5/8"
CUTTER,TUBE,MINI,1/8" TO 7/8"
114.64
46.21
PVC PIPE CUTTERS
Copper Tubing Cutters and Replacement Wheels
443
Tools
PVC PIPE CUTTERS
CPS Products Copper Tubing Cutters and Replacement Wheels
Features:
•
•
•
•
Ideal for cutting pipe in limited access areas
Titanium nitride treated cutting wheel for added blade life
Advanced tracking system will not walk while cutting
Heavy duty construction and performance for professional use
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CP-TCT127
S1-CP-TCT174
S1-CP-TCT274
S1-CP-TCXT127C
CUTTER,TUBE,HD,1/8"-5/8"
CUTTER,TUBE,HD,1/8"-1 1/8"
CUTTER,TUBE,HD,OD,1/8"-1 3/8"
CUTTER,TUBE,TIGHT SPACE,OD,1/8"-5/8"
27.54
50.93
83.11
7.89
DiversiTech Big Helper PVC Pipe Cutter
Ratchet style pipe cutters cut up to 2-1/2” Sch. 40 PVC Pipe. Ratchet action requires minimal pressure to easily cut through PVC pipe.
Molybdenum stainless steel blade won’t rust or break and lasts twice as long as most competitor’s. The Mega-Cutter is now available
– the strongest pipe cutter on the market today!
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-548-003
S1-548-004
S1-548-005
S1-548-006
S1-548-007
S1-548-008
S1-548-009
S1-548-010
1” O.D. CUTTING CAPACITY
1” REPLACEMENT BLADE
1-1/4” O.D. CUTTING CAPACITY
1-1/4” REPLACEMENT BLADE
2-1/2” O.D. MEGA-CUTTER
2-1/2” MEGA-BLADE
1-5/8” O.D. CUTTING CAPACITY
1-5/8” REPLACEMENT BLADE
27.64
17.46
41.29
18.64
153.71
56.54
42.04
18.64
Lenox Tubing, PVC, and Pipe Cutters
Lenox tubing cutters are ergonomically designed for professional use, prevent walking, and have convenient storage for extra cutting
wheels. Replaceable reamers ensure burr free cuts in copper pipe.
SOURCE 1 PART NO.
S1-12121S1
S1-12122S2
S1-21008TC58
S1-21009TC1
S1-21010TC118
S1-21011TC138
S1-21012TC134
S1-21192TCW158C2
S1-21193TCW158SS2
DESCRIPTION
PRODUCT APPLICATION
MLP $
PLASTIC PIPE CUTTER-S1 SCISSOR CUT 1-5/16 (S1)
PLASTIC PIPE CUTTER-S2 DIRECT CUT 1-5/16 (S2)
TUBING CUTTER 1/8" - 5/8"
TUBING CUTTER 1/8" - 1"
TUBING CUTTER 1/8" - 1-1/8"
CUTTING WHEELS COPPER 2 PK
CUTTING WHEELS STAINLESS STEEL 2 PK
CUTTING PLASTIC TUBING
CUTTING CPVC
CUTTING COPPER
CUTTING COPPER
CUTTING COPPER
CUTTING COPPER
CUTTING COPPER
CUTTING COPPER
CUTTING COPPER
58.82
85.96
36.11
67.00
74.79
107.79
161.29
19.43
19.43
444
Tools
SNIPS
Lenox Snips and HVAC Tools
Lenox Snips and HVAC tools are designed to meet the pro's needs. Precision formed blades and reinforced
chrome springs allow for optimal blade life and durability. Overm olded grips won't slip or twist.
SOURCE 1 PART NO.
DESCRIPTION
PRODUCT APPLICATION
MLP $
S1-22101101
S1-22102102
S1-22103103
S1-22105105
S1-22206206
S1-22207207
S1-22208C3
S1-22209C5
S1-22210S2
SNIPS HVAC-101 AVIATION SNIP LEFT
SNIPS HVAC-102 AVIATION SNIP RIGHT
SNIPS HVAC-103 AVIATION SNIP STRAIGHT
AVIATION SNIP BULLDOG
OFFSET SNIP LEFT
OFFSET SNIP RIGHT
C3 3 BLADE CRIMPER
C5 5 BLADE CRIMPER
S2 3 INCH SEAMER
45.21
45.21
45.21
55.68
61.86
61.86
50.25
77.32
97.93
S1-22211N2
N2 V NOTCHER
S1-22212SL1
SL1 SNAP LOCK PUNCH
S1-22213PDC4R
PDC4R PIPE DUCT CUTTER
CUTTING SHEET METAL
CUTTING SHEET METAL
CUTTING SHEET METAL
CUTTING SHEET METAL
CUTTING SHEET METAL
CUTTING SHEET METAL
CRIMPING SHEET METAL
CRIMPING SHEET METAL
SHEET METAL
FABRICATION
SHEET METAL
FABRICATION
SHEET METAL
FABRICATION
SHEET METAL
FABRICATION
GENERAL
SCREWDRIVING
S1-23932
9-IN-1 SCREWDRIVER
77.32
77.32
77.32
30.82
Midwest® Aviation Snips
Moly alloy tool steel blade is hot drop-forged and scientifically heat-treated to provide a strong, longer lasting
cutting edge. Durable serrated blades are designed to grip the metal for cutting ease. The patent pending spring
on these snips is guaranteed to last for the life of the tool. Will cut 18 gauge coldrolled steel.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-540-6716B
AVIATION SNIP – BULLDOG NOTCHING SNIP – YELLOW
HANDLE
AVIATION SNIP – CUTS LEFT – RED HANDLE
AVIATION SNIP – CUTS RIGHT – GREEN HANDLE
AVIATION SNIP – CUTS STRAIGHT – YELLOW HANDLE
6
42.29
6
6
6
38.54
38.54
38.54
S1-540-6716L
S1-540-6716R
S1-540-6716S
®
Midwest Offset Snips
T he same high quality construction as the Aviation Snips with an additional advantage – the Offset Snips allow
your hand to stay above metal for cutting ease and com fort.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-540-6510L
S1-540-6510R
OFFSET SNIP – CUTS LEFT – RED HANDLE
OFFSET SNIP – CUTS RIGHT – GREEN HANDLE
6
6
49.68
49.68
445
Tools
SNIPS
Midwest® Tinner Snips
Constructed of the finest quality high carbon tool steel. Hot drop-forged and heat-treated to assure strength and
durability. “Kush-N-Cote” vinyl coated handles for added comfort. Available in a Straight Pattern for a powerful
straight cutting snip or Duckbill Pattern for cutting scrolls, circles, or straight lines. 12-1/2” long.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-540-P127D
S1-540-P127S
DUCKBILL TINNER SNIP
STRAIGHT CUTTING TINNER SNIP
6
6
54.18
50.07
®
Midwest Upright Snips
T his snip significantly improves sheet m etal cutting. T he ergonomic design allows for easier cutting in tight
places, im proved safety by elevating hands above m etal working surfaces, and increases wrist range m otion.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-540-6900L
S1-540-6900R
UPRIGHT SNIPS – LEFT-HANDED MODEL
UPRIGHT SNIPS – RIGHT-HANDED MODEL
6
6
58.32
58.32
SPRAYERS & COIL GUNS
DiversiTech All Purpose Sprayers
Lightweight, versatile gallon size bottle has a 28” flexible hose and easy-to-carry handle. Best for big jobs in
hard- to-reach places. Adjustable nozzle will atomize any low viscosity liquid. Adjusts from a mist to a 12’ jet
stream or anything in between. One pint container has a measured ounce guide. Ideal for water treatment
chemicals.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-BS-16
S1-BS-32
S1-BS-64
PINT SIZE SPRAYER
QUART SIZE SPRAYER
GALLON SIZE SPRAYER
12
12
6
4.89
6.46
14.18
446
Tools
SPRAYERS & COIL GUNS
DiversiTech Compression Sprayers
Acid impervious poly design with a 36” (91cm) reinforced hose, shut-off with lockon feature for continuous
spraying, a 2-piece nozzle that’s detachable for easy clean up and fits directly to the shut-off or extension wand.
The Hand-Held Sprayer has a 48 oz. (1.4 l) capacity, perfect for small areas. All sprayers have a full 5 year
warranty.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-1002
S1-2602
S1-2603
HAND HELD SPRAYER
2 GALLON WAND SPRAYER
3 GALLON WAND SPRAYER
36.71
92.89
100.00
DiversiTech Dial-a-Mix Coil Gun
Save time and money by dialing in the exact mix ratio to properly clean the coil. This gun features 5 mix ratios,
a 1/2 gallon capacity bottle and a quick disconnect for fast and easy rinsing.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-540-GUN
DIAL-A-MIX COIL GUN
6
197.29
*Sold by Standard Pack / M LP per each.
ALLEN WRENCHES
Allen Duracast Fold Ups
Unique “double foldout” design. This convenient pocket wrench set opens from both the top and bottom for fast, easy access to each
and every bit. Instead of unfolding the top wrenches to get at the wrenches underneath, just turn the FOLD UP over. Specially
contoured handle, so you’ll never cut your hands or snag clothing.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-AWZ-2500
S1-AWZ-3000
3-1/2” HANDLE, 9 BITS .050”, 1/16”, 5/64”, 3/32”, 7/64”, 1/8”, 9/64”, 5/32”, 3/16”
4-1/4” HANDLE, 9 BITS 5/64”, 3/32”, 7/64”, 1/8”, 9/64”, 5/32”, 3/16”, 7/32”, 1/4”
40.29
44.96
DiversiTech Allen Wrenches
The finest quality wrenches available anywhere.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-AW-8
3” HANDLE, 8 BITS, STANDARD FOLD-UPS .050”, 1/16”, 5/64”, 3/32”, 7/64”, 1/8”,
9/64”, 5/32”
4” HANDLE, 9 BITS, STANDARD FOLD-UPS 5/64”, 3/32”, 7/64”, 1/8”, 9/64”, 5/32”,
3/16”, 7/32”, 1/4”
5-1/4” HANDLE, 5 BITS, LONG ARM FOLD-UPS 3/16”, 7/32”, 1/4”, 5/16”, 3/8”
6-1/4” HANDLE, 9 BITS, LONG ARM FOLD-UPS 5/64”, 3/32”, 7/64”, 1/8”, 9/64”,
5/32”, 3/16”, 7/32”, 1/4”
14.96
S1-AW-9
S1-AWL-5
S1-AWL-9
447
22.96
32.25
30.07
Tools
ALLEN WRENCHES
DiversiTech Allen Wrenches – Individual Sizes
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-AW-712-10
S1-AW-712-8
S1-AW-96-10
S1-AW-96-8
ALLEN WRENCH 12” x 5/32”
25
25
25
25
10.46
10.29
4.57
2.82
DiversiTech Allen Wrenches – Long Arm
Most needed combination of Allen Wrenches packaged in clearly marked vinyl pouches.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-AW-712
S1-AW-96
7 KEYS, 12” LONG ARM SERIES: 5/64”, 3/32”, 1/8”, 5/32”, 3/16”, 7/32”, 1/4”
9 KEYS, 6” LONG ARM SERIES: 5/64”, 3/32”, 1/8”, 5/32”, 3/16”, 7/32”, 1/4”, 5/16”,
3/8”
74.96
55.57
AMP EXTRACTION TOOLS
Model - S1-52118452000
Features:
• Designed to remove Amp COMMERCIAL Mate-N-Lok contacts from their housings
• For pin or socket
• Instruction sheet included
• For use with 25, 30, 48 ton DSC, DSV units and 50 thru 100 ton YIC & YIV units
SOURCE 1 PART NO.
AMP CATALOG NO.
MLP $
S1-52118452000
465644-1
50.46
448
Tools
Model - S1-52118453000
Features:
• Designed to remove Amp UNIVERSAL Mate-N-Lok pin & socket contacts from the connectors
• Approx. 4.50" long x 3/4 diameter
• Clips on pocket for easy carrying
• For use with commercial products 3 ton thru 25 ton
SOURCE 1 PART NO.
AMP CATALOG NO.
MLP $
S1-52118453000
458994-2
135.79
SOURCE 1 PART NO.
AMP CATALOG NO.
MLP $
S1-52118454000
189727-1
75.82
Model - S1-52118454000
Features:
• Designed to remove Amp Mini-Universal Mate-N-Lok contacts from housing cavities
• Push rod inserts into the contact housing for easy removal of contact
• For use on T riathlon products
449
Tools
Model - S1-52118456000
Features:
• Designed to remove Amp bifurcated leaf contacts from their housings
• Approx. 2" long x 1/2" wide
• Extraction tip inserts into housing for easy removal of contact
• For use with commercial products 3 ton thru 25 ton
SOURCE 1 PART NO.
AMP CATALOG NO.
MLP $
S1-52118456000
90471-1
58.71
450
Tools
FLASHLIGHTS, HEADLAMPS & BATTERIES
FLASHLIGHTS
MAG-LITE
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-7S4D016
4 CELL D MAG-LITE FLASHLIGHT - BLACK
89.18
Rayovac Batteries
SOURCE 1 PART NO.
DESCRIPTION
SIZE
QTY PER PKG
QTY PER CASE
MLP $ PER PACK*
MLP $
S1-AL-9V
S1-AL-AA
S1-AL-AAA
S1-AL-C
S1-AL-D
ALKALINE INDUSTRIAL GRADE BATTERIES
9 VOLT
AA
AAA
C
D
6
8
8
6
6
72
96
96
72
72
3.64
1.00
1.04
1.93
2.46
3.68
1.00
1.04
2.00
2.50
* Pri cing per battery, but sold per pack or per case.
Rayovac Flashlights
SOURCE 1 PART NO.
DESCRIPTION
USES BATTERIES
MLP $
S1-IN2-K
S1-R2AA-BA
INDUSTRIAL FLASHLIGHT
ROUGHNECK FLASHLIGHT
2 D CELLS
2 AA CELLS *
11.93
17.75
* B atteries i ncl uded
451
Tools
STAPLE GUNS, CONDENSER TUBE CLEANERS & CALIPERS
DiversiTech Digital Fractional Calipers
•
•
•
•
•
•
Heavy Duty Stainless Steel Construction.
Convenient Auto On/Off Feature.
Three Mode Digital Display: Decimal Inches, Fractions, Metric.
Accuracy: +/- 0.001” +/- 0.02mm.
Resolution: 0.0005”, 0.01mm, 1/64”.
Includes: 1 “LR44/357” battery.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-T147
RANGE: 0 - 6” (0 - 153MM)
127.86
DiversiTech Expando Adjustable Condenser Tube Cleaner
Fast, thorough, economical way to remove mineral scale and sludge from inside water-cooled condenser tubes. Saves timeconsuming brushing or flushing. Expando attaches to a threaded rod which fits into an Expando handle or your electric drill. With a
reaming action, the tough stainless steel blades scrape everywhere inside the tube, providing a free, unrestricted flow. Virtually
clogproof, this tool may be expanded or reduced in diameter to fit scale deposits — not just the tube. Note: Use S1-EC-810 couplings
for connecting additional rods.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-E-10
S1-E-5
S1-E-6
S1-E-8
S1-EB-10
S1-EB-6
S1-EB-8
S1-EC-56
S1-EC-810
S1-EH-1
CONDENSER TUBE CLEANER – 5/8” TO 3/4” I.D. TUBES
BLADES FOR E-10
BLADES FOR E-5 AND E-6
BLADES FOR E-8
COUPLINGS FOR E-5 AND E-6
COUPLINGS FOR E-8 AND E-10
HANDLE
1
1
1
1
1
1
1
3
3
1
33.14
33.14
33.14
33.14
6.46
6.46
6.46
3.25
3.25
5.04
**MLP per pack.
DiversiTech T-50 Series Staples and Staple Guns
The #1 selling staple gun in the world! Used extensively by building contractors, home do-it-yourselfers and specialty trade
applications for tacking insulation, ceiling tile, window screening, cornerite, and 1001 other jobs ranging from light to heavy duty work.
The T-50 Outward Clinch Staple Gun is ideal for fiberglass ductwork.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-540-504
S1-540-506
S1-540-508
S1-540-509
S1-540-T50M
S1-540-T50MOC
1/4” LEG STAPLES FOR T50 STAPLE GUNS (1250/PK)
T50M HEAVY DUTY STAPLE GUN TACKER
T50MOC OUTWARD CLINCH STAPLE GUN
4
4
4
4
1
1
10.04
8.61
9.18
9.86
101.04
153.00
PLIERS
Channellock Tongue and Groove Pliers
Patented desi gn, permalock fasteners and reinforcing edge. Dipped plasti c com fort gri ps.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-545-420
S1-545-422
S1-545-424
S1-545-426
S1-545-430
S1-545-440
S1-545-442
S1-545-460
9-1/2” TONGUE AND GROOVE PLIERS
9-1/2” CURVED JAW TONGUE AND GROOVE PLIERS
10” TONGUE AND GROOVE PLIERS
12” CURVED JAW TONGUE AND GROOVE PLIERS
48.93
48.93
47.18
40.71
51.04
54.86
54.86
95.79
452
Tools
PLIERS
DiversiTech “Mini” Lineman’s Pliers
•
•
•
•
•
For securing a positive grip on flat objects to form a bend.
Serrated jaws for better grip.
Side cutter will handle most cutting requirements.
Overall jaw length - 7/8” (22mm).
Overall length - 4-1/2” (114mm).
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-T908
“MINI” LINEMAN’S PLIERS
11.18
IRWIN Groove Lock Pliers
IRWIN Vise Grip Groove Lock Pliers have a push button design that allows for 2 times faster adjustability over the standard tongue and groove adjustable plier.
Groove Lock Pliers also provide twice the amount of groove positions for precision adjustments.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-2078108
S1-2078110
S1-2078112
S1-2078116
S1-2078120
S1-2078709
S1-2078710
S1-2078711
S1-4935095
S1-4935096
S1-4935097
S1-4935098
S1-4935099
S1-4935351
GV8 GROOVELOCK 8" V JAW PLIERS
2 PC. GROOVELOCK PLIERS SET CONTAINS: GV8, GV10
3 PC. GROOVELOCK TRAY SET CONTAINS: GV8, GV10, GV12
3 PC. GROOVELOCK KITBAG SET CONTAINS GV8, GV10, GV12
GV8R GROOVELOCK 8" STRAIGHT JAW PLIERS
GV10S GROOVELOCK 10" SMOOTH JAW PLIERS
GV12S GROOVELOCK 12" SMOOTH JAW PLIERS
31.18
37.46
45.00
86.18
114.93
58.54
112.54
140.46
31.18
37.46
39.36
45.00
47.21
27.39
IRWIN Vise-Grip Insulated Pliers
IRWIN Vise Grip insulated pliers have strong hardened teeth with slim profile noses to reach tight areas. All insulated pliers are regulated for 1000 volt usage.
T he Pro T ouch grips provide m axim um comfort and reduced hand fatigue.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-10505865NA
S1-10505866NA
S1-10505867NA
S1-10505868NA
S1-10505869NA
S1-10505870NA
S1-10505871NA
S1-10505872NA
S1-10505873NA
S1-10505874NA
S1-10507529NA
6" INSULATED DIAGONAL CUTTER - STANDARD
7" INSULATED HIGH LEVERAGE DIAGONAL CUTTER
8" INSULATED HIGH LEVERAGE DIAGONAL CUTTER
6" INSULATED LONG NOSE - STANDARD
8" INSULATED LONG NOSE - HIGH LEVERAGE
8" INSULATED BENT NOSE - HIGH LEVERAGE
6" INSULATED WIRE STRIPPER
6" INSULATED COMBINATION - STANDARD
7" INSULATED COMBINATION - HIGH LEVERAGE
8" INSULATED COMBINATION - HIGH LEVERAGE
8.5" INSULATED LINEMAN’S PLIERS
56.82
63.46
65.71
66.93
73.43
75.18
66.93
59.32
67.68
71.04
76.07
453
Tools
PLIERS
IRWIN Vise-Grip Locking Pliers
IRWIN Vise Grips are the original locking plier offering the largest jaw configurations for every application. T he new Fast Release are not only 2 times faster to
use than standard locking pliers, they also provide 3 times more gripping pressure.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-1002L3
S1-102L3
S1-11T
S1-13T
S1-1402L3
S1-14T
S1-1502L3
S1-15T
S1-1602L3
S1-1T
S1-302L3
S1-3T
S1-4935576
S1-4935578
S1-4935579
S1-4935581
S1-502L3
S1-5T
S1-702L3
S1-7T
S1-902L3
S1-9T
4WR® ORIGINAL CURVED JAW W/WIRE CUTTER 4" / 100 MM - CARDED LOCKING PLIER
10R® ORIGINAL STRAIGHT JAW 10" / 250 MM CARDED LOCKING PLIER
10CR® FAST RELEASE CURVED JAW 10" / 250 MM - CARDED LOCKING PLIER
7CR® FAST RELEASE CURVED JAW 7" / 175 MM CARDED LOCKING PLIER
6LN® ORIGINAL LONG NOSE 6"/150 MM CARDED LOCKING PLIER
6LN® FAST RELEASE LONG NOSE 6"/150 MM LOCKING PLIER
9LN® ORIGINAL LONG NOSE 9" / 225 MM CARDED LOCKING PLIER
9LN® FAST RELEASE LONG NOSE 9" / 225 MM CARDED LOCKING PLIER
4LN® ORIGNAL LONG NOSE 4" / 100 MM CARDED LOCKING PLIER
10R® FAST RELEASE STRAIGHT JAW - 10" / 250 MM - CARDED LOCKING PLIER
7R® ORIGINAL STRAIGHT JAW 7" / 175 MM CARDED LOCKING PLIER
7R® FAST RELEASE STRAIGHT JAW 7" / 175 MM CARDED LOCKING PLIER
10CR® ORIGINAL CURVED JAW 10" / 250 MM - CARDED LOCKING PLIER
7CR® ORIGINAL CURVED JAW 7" / 175 MM CARDED LOCKING PLIER
5CR® ORIGINAL CURVED JAW 5" / 125 MM - CARDED LOCKING PLIER
5CR® FAST RELEASE CURVED JAW 5" / 125 MM - CARDED LOCKING PLIER
10WR® FAST RELEASE CURVED JAW W/WIRE CUTTER 10" / 250 MM LOCKING PLIER
7WR® ORIGINAL CURVED JAW W/WIRE CUTTER 7" / 175 MM CARDED LOCKING PLIER
7WR® FAST RELEASE CURVED JAW W/WIRE CUTTER 7"/175 MM LOCKING PLIER
5WR® FAST RELEASE CURVED JAW W/WIRE CUTTER 5"/125 MM CARDED LOCKING PLIER
23.61
26.93
29.57
29.11
27.71
30.46
33.25
36.57
26.07
29.57
26.46
29.11
26.93
26.46
25.75
28.39
26.93
29.57
26.46
29.11
25.75
28.32
SCREWDRIVERS
DiversiTech 5-Piece Precision UltratechTM Phillips Screwdriver Set
•
•
•
•
•
Driver tip size shown on cap.
Rotating cap; Facets fit palm, recess fits finger tip, Color coded ring identifies type of tip.
Body sized to prevent excessive torque to fastener.
8-Sided non-slip cushion grip.
8650 Alloy steel (nickel-chromiummolybdenum), Chrome plated to resist corrosion.
SOURCE 1 PART NO.
DESCRIPTION
TYPE
SIZE
BLADE LENGTH
MLP $
S1-6-T700
5-PIECE SET:
PHILLIPS, PHILLIPS,
SLOTTED, PHILLIPS,
SLOTTED
3/32” (2.5MM), 1/8”
(3.0MM), NO. 00, NO. 0,
NO. 1
1-1/2 (38MM), 2-1/2 (64MM),
1-1/2 (38MM), 2-1/2 (64MM),
2-1/2 (64MM)
51.75
DiversiTech Combination Screwdriver
Multiple bits in one handy screwdriver. No need for a toolbox for those quick jobs. Lifetime guarantee.
SOURCE 1 PART NO.
DESCRIPTION
STD. PACK
MLP $
S1-5-41
S1-5-61
4-IN-1 WITH #1 AND #2 PHILLIPS, 3/16 AND 5/16 SLOTTED
6-IN-1 WITH #1 AND #2 PHILLIPS, 3/16 AND 5/16 SLOTTED 1/4 NUT
DRIVER, 5/16 NUT DRIVER
12
12
15.11
17.57
DiversiTech Pocket 4-in-1 Mini Screwdriver
•
•
•
•
•
•
This screwdriver is ideal for technicians, hobbyists and do-it-yourselfers.
2 double-ended chrome vanadium blades.
1/16” and 1/8” slotted tip and #1 and #00 crosspoin tip.
Blades are held in carrier handle.
Change blade sizes instantly.
Convenient pocket clip and capped ends.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-T744
POCKET 4-IN-1 MINI SCREWDRIVER – LENGTH: 5-1/8” (130MM)
6.75
454
Tools
BIT DRIVERS
DiversiTech 28-Piece Bit Driver Set—16-in-1 Plus
Set Includes:
• 8 double-ended hardened alloy steel precision blades. Zinc plated to prevent rust.
– Phillips - #0 x #000
– Phillips/Slotted - #0000 x 3/64”
– Slotted - 1/8” x 5/64”
– Hex - .050” x 1/16”, 5/64” x 3/32”
– Torx - T5 x T8, T6 x T10
– Square Recess - #0 x #1
• Magnetic Insert Bit Holder
• Industry Standard Insert Bits
– Slotted - 3/16”, 1/4”
– Phillips - #1, #2
– Torx® - T15, T20, T25
– Hex - 1/8”, 5/32”, 3/16”
– #2 Square Recess.
• Convenient storage under cap for all 8 blades, Packaged in a fitted Ballistic Nylon Holster.
• Vinyl holster insert holds 11 insert bits and one magnetic insert bit holder.
• Precision engineered 750 Series Versa- GripT M handle for maximum performance.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-6-T751028
28-PIECE BIT DRIVER SET (HOLSTER/CARDED)
75.00
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CP-TLSWO
S1-CP-TLSWS
S1-CP-TLSWSA
S1-CP-TLTWSAE
S1-CP-TLTWSM
TOOL,SERVICE WRENCH OFFSET
TOOL,SERVICE WRENCH STRAIGHT
TOOL,SERVICE WRENCH W/ADAPTER
TOOL,KIT,SAE TORQUE WRENCH
TOOL,KIT,METRIC TORQUE WRENCH
28.07
27.29
49.61
189.21
189.21
WRENCHES
CPS Products Wrenches
UTILITY KNIVES, TOOL BAGS & CLIPBOARDS
16" Contractors Bag
Features:
• Large zippered compartment, side pockets
• Removable shoulder strap
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-4402020
16" CONTRACTOR'S BAG
58.21
455
Tools
16" Utility Tote
Features:
• Open main storage compartments, side pockets, 24" level storage
• Removable shoulder strap
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-4402016
16" TOOL UTILITY TOTE
99.29
CPS Products Square Tool Organizer
Square tool organizer with "open mouth" design
Features:
• Self standing square tool organizer
• Large "open mouth" design for easy access and visibility
• 15 external pockets and loops hold a wide variety of tools including 2 flap covered pockets and 1 zipper
pocket
• 7 internal loops with 2 sized for holding instruments
• Ergonomic carrying handle with adjustable shoulder strap
• Measures 16" x 8 ½" x 8 ½"
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-CP-TLBAG1
TOOL,BAG/ORGANIZER,SQUARE
67.54
DiversiTech BigMouth Bag
Internal metal frame holds bag wide open for easy access to tools and supplies. Reinforced interior bottom
panel enables the BigMouth bag to keep its wide profile. Padded sides and bottom. Built of super tough, super
light fabric.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-5-1135
BIGMOUTH BAG
81.93
456
Tools
DiversiTech Clipboards and Form Holders
Rugged aluminum construction to protect your paperwork and forms. Smooth aluminum surfaces provide
excellent writing support.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-30306
S1-30309
S1-30310
SNAPAK CLIPBOARD ON BOX W/HINGED BACK – 8-1/2” x 12”
REDI-RITE CLIPBOARD ON BOX – 8-1/2” x 12”
CRUISER MATE 2 COMPARTMENT CLIPBOARD – 8-1/2” x 12”
89.68
84.96
95.50
DiversiTech Double Zipper Rigger’s Bag
Rugged, lightweight soft-sided tote/organizer for tools and business accessories. Features double pull top zipper
for easy access, reinforced bottom panel to keep bag’s wide profile, and padded carrying handle. T otal of 50
multiuse pockets!
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-5-1115
DOUBLE ZIPPER RIGGER’S BAG
97.79
Lenox Gold Utility Knives and Blades
High Speed steel cutting edge with titanium coating allows the Lenox Utility Blades to last longer than other
utility blades. Bi-metal construction makes Lenox Utility Blades shatterproof. Lenox Locking T radesmen Utility
Knife is easy to open and has a multi-tool function with a screwdriver, pipe reamer, and bottle opener built into
the handle.
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-10771FLK1
S1-20350GOLD5C
LOCKING TRADESMAN KNIFE
BLADES 5 PK
39.57
1.50
Pro Utility Tool Organizer
Features:
• Enough capacity to carry a broad range of tools and accessories
• Pockets and compartments designed to provide better organization
SOURCE 1 PART NO.
DESCRIPTION
MLP $
S1-420004
16" TOOL ORGANIZER BAG
72.00
457
—NOTES—
458
—NOTES—
459
—NOTES—
460
—NOTES—
461
—NOTES—
462
—NOTES—
463
—NOTES—
464
General Information
ALTITUDE PRESSURE TABLE
MERCURY AT 0° C (32° F.)
ALTITUDE IN FEET
-1,000
0
1,000
2,000
3,000
4,000
5,000
6,000
7,000
8,000
9,000
10,000
15,000
20,000
25,000
30,000
35,000
40,000
45,000
50,000
INCHES OF MERCURY
31.02
29.921
28.86
27.82
26.81
25.84
24.8Y
23.98
23.09
22.22
21.38
20.58
16.88
13.75
11.10
8.88
7.04
5.54
4.36
3.436
VOLUME EQUIVALENTS
1728 CU. IN.
7.481 GAL. (U.S.)
1 CU. FT. =
28.317 LITERS
28,317 CU. CM.
231 CU. IN.
.1337 CU. FT.
1 GAL. (U.S.) =
3.785 LITERS
3785 CU. CM.
.0353 CU. FT.
1 LITER =
.2642 GAL. (U.S.)
1000 CU. CM.
IN
MILLIMETERS
OF MERCURY
787.9
760.0
732.9
706.6
681.1
656.3
632.3
609.0
586.4
564.4
543.2
522.6
428.8
349.1
281.9
225.6
178.7
140.7
110.8
87.30
DIAM.
IN INCHES
1
1-1/2
2
2-1/2
3
3-1/2
4
4-1/2
5
5-1/2
6
6-1/2
7
7-1/2
8
8-1/2
9
9-1/2
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
SPECIFIC GRAVITIES OF GASES
(BASED ON 68°F. AND 14.7 LBS. ABS.)
ACETYLENE
C2H2
.897
AIR
1.000
AMMONIA
NH3
.587
ARGON
A
1.378
BUTANE-N
C4H40
2.390
BUTANE-ISO
(CH)3)2CH
1.990
CH3
CARBON DIOXIDE
CO2
1.517
CARBON MONOXIDE
CO
.966
CHLORINE
CL2
2.452
ETHANE
C2H6
1.035
HELIUM
HE
.138
HYDROGEN
H2
.070
METHANE
CH4
.553
NATURAL GAS
.665 (APPROX. AVG.)
NITRIC OXIDE
NO
1.035
NITROGEN
N2
.966
NITROUS OXIDE
N2O
1.518
OXYGEN
O2
1.103
PROPANE
C3H8
1.550
SULPHUR DIOXIDE
SO2
2.209
1 CU. FT./HR.
.0166
CU. FT./MIN.
.4719
LPM
28.316
LPH
471.947
CC/MIN.
28317
CC/HR.
.1247
GAL/MIN.
7.481
GAL/HR.
1 LPM
60.
LPH
.035
CU. FT./MIN.
2.1189
CU. FT./HR.
1000
CC/MIN.
60,002
CC/HR.
.264
GAL/MIN.
15.851
GAL/HR.
AREA OF CIRCLES IN FT2
AREA
DIAM.
SQUARE FEET
IN INCHES
.0054
30
.0123
31
.0218
32
.0341
33
.0491
34
.0668
35
.0873
36
.1105
37
.1364
38
.1650
39
.1964
40
.2305
41
.2673
42
.3068
43
.3491
44
.3940
45
.4418
46
.4923
47
.5454
48
.6600
49
.7854
50
.9218
51
1.069
52
1.227
53
1.396
54
1.576
56
1.767
58
1.969
60
2.182
62
2.405
64
2.640
66
2.885
68
3.142
70
3.409
72
3.687
74
3.976
76
4.276
78
FLOW EQUIVALENTS
1 CU. FT./MIN.
1 CC/MIN.
60
CU. FT./HR.
60
CC/HR.
28.316
LPM
.000035
CU. FT./MIN.
1699
LPH
.0021
CU. FT./HR.
28317
CC/MIN.
.001
LPM
1,699,011
CC/HR.
.06
LPH
7.481
GAL/MIN.
.00026
GAL/MIN.
448.831
GAL/HR.
.0159
GAL/HR.
1 LPH
1 GAL/MIN.
.0166
LPM
60
GAL/HR.
.00059
CU. FT./MIN.
.1337
CU. FT./MIN.
.035
CU. FT./HR.
8.021
CU. FT./HR.
16.667
CC/MIN.
3.785
LPM
1000
CC/HR.
227.118
LPH
.004
GAL/MIN.
3,785.412
CC/MIN.
.264
GAL/HR.
227,125
CC/HR.
465
AREA
SQUARE FEET
4.909
5.241
5.585
5.940
6.305
6.611
7.069
7.467
7.876
8.296
8.727
9.168
9.621
10.08
10.56
11.04
11.54
12.05
12.57
13.10
13.64
14.19
14.75
15.32
15.90
17.10
18.35
19.63
20.97
22.34
23.76
25.22
26.73
28.27
29.87
31.50
33.18
1 CC/HR.
.0167
.0000005
.00003
.000017
.001
.000004
.00026
CC/MIN.
CU. FT./MIN.
CU. FT./HR.
LPM
LPH
GAL/MIN.
GAL/HR.
1 GAL/HR.
.0167
GAL/MIN.
.002
CU. FT./MIN.
.1337
CU. FT./HR.
.063
LPM
3.785
LPH
63.069
CC/MIN.
3785
CC/HR.
Pressure Conversion Chart
IN./H2O
.1
.2
.4
.6
.8
1.0
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
P.S.I.
.0036
.0072
.0144
.0216
.0289
.0361
.0722
.1083
.1444
.1804
.2165
.2526
.2887
.3248
.3609
.3970
.4331
.4692
.5053
.5414
.5774
.6136
.6496
.6857
.7218
.7579
.7940
.8301
.8662
.9023
.9384
.9745
1.010
1.047
1.083
1.119
1.155
1.191
1.227
1.263
1.299
1.335
1.371
1.408
1.444
1.480
1.516
1.552
1.588
1.624
1.660
1.696
1.732
1.768
1.804
1.841
1.877
1.913
IN./Hg
.0073
.0146
.0293
.0440
.0588
.0735
.1470
.2205
.2940
.3673
.4408
.5143
.5878
.6613
.7348
.8083
.8818
.9553
1.029
1.102
1.176
1.249
1.322
1.396
1.470
1.543
1.616
1.690
1.764
1.837
1.910
1.984
2.056
2.132
2.205
2.278
2.352
2.425
2.498
2.571
2.645
2.718
2.791
2.867
2.940
3.013
3.086
3.160
3.233
3.306
3.378
3.453
3.526
3.600
3.673
3.748
3.822
3.895
MM/H2O
2.534
5.867
10.13
15.20
20.34
25.41
50.81
76.22
101.62
127.0
152.4
177.8
203.2
228.0
254.0
279.4
304.8
330.2
355.6
381.0
406.4
431.8
457.2
482.6
508.0
533.4
558.8
584.2
609.6
635.0
660.4
685.8
710.8
736.8
762.2
787.5
812.8
838.2
863.5
888.9
914.2
939.5
964.9
990.9
1016
1042
1067
1092
1118
1143
1158
1194
1219
1244
1270
1296
1321
1346
MM/Hg
.1863
.3726
.7452
1.118
1.496
1.868
3.736
5.604
7.472
9.335
11.203
13.072
14.940
16.808
18.676
20.544
22.412
24.280
26.148
28.016
29.879
31.752
33.616
35.484
37.352
39.22
41.09
42.96
44.82
46.69
48.56
50.43
52.26
54.18
56.04
57.91
59.77
61.63
63.49
55.36
67.22
69.08
70.95
72.86
74.72
76.59
78.45
80.31
82.18
84.04
85.90
87.76
89.63
91.49
93.35
95.27
97.13
98.99
KG/CM
.0002
.0005
.0010
.0015
.0020
.0025
.0051
.0076
.0102
.0127
.0152
.0178
.0203
.0228
.0254
.0279
.0304
.0330
.0355
.0381
.0406
.0431
.0457
.0482
.0507
.0533
.0558
.0584
.0609
.0634
.0660
.0685
.0710
.0736
.0761
.0787
.0812
.0837
.0862
.0888
.0913
.0938
.0964
.0990
.1015
.1049
.1066
.1091
.1116
.1142
.1167
.1192
.1218
.1243
.1268
.1294
.1320
.1345
2
BAR
.0002
.0005
.0010
.0015
.0020
.0025
.0050
.0075
.0099
.0124
.0149
.0174
.0199
.0224
.0249
.0274
.0299
.0324
.0348
.0373
.0398
.0423
.0448
.0473
.0498
.0523
.0547
.0572
.0597
.0622
.0647
.0672
.0696
.0722
.0747
.0772
.0796
.0821
.0846
.0871
.0896
.0920
.0945
.0971
.0996
.1020
.1045
.1070
.1095
.1120
.1144
.1169
.1194
.1219
.1244
.1269
.1294
.1319
MBAR
.2482
.4964
.9928
1.489
1.992
2.489
4.978
7.467
9.956
12.44
14.93
17.42
19.90
22.39
24.88
27.37
29.86
32.35
34.84
37.33
39.81
42.31
44.79
47.28
49.77
52.26
54.74
57.23
59.72
62.21
64.70
67.19
59.64
72.19
74.67
77.15
79.63
82.12
84.60
67.08
89.56
92.04
94.53
97.08
99.56
102.0
104.5
107.0
109.5
112.0
114.5
118.9
119.4
121.9
124.4
126.9
129.4
131.9
PA
24.82
49.64
99.28
148.9
199.2
248.9
497.8
746.7
995.6
1244
1493
1742
1990
2239
2488
2737
2986
3235
3484
3733
3981
4231
4479
4728
4977
5226
5474
5723
5972
6221
6470
6719
6964
7219
7467
7715
7963
8212
8460
8708
8956
9204
9453
9708
9956
10204
10452
10701
10949
11197
11445
11694
11942
12190
12438
12693
12941
13190
KPA
.0248
.0496
.0993
.1489
.1992
.2489
.4978
.7467
.9956
1.244
1.493
1.742
1.990
2.239
2.488
2.737
2.986
3.235
3.484
3.733
3.981
4.231
4.479
4.728
4.977
5.226
5.474
5.723
5.972
6.221
6.470
6.719
8.964
7.219
7.467
7.715
7.963
8.212
8.460
8.708
8.956
9.204
9.453
9.708
9.956
10.20
10.45
10.70
10.95
11.20
11.44
11.69
11.94
12.19
12.44
12.69
12.94
13.19
466
IN./H2O
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
P.S.I.
1.949
1.985
2.021
2.057
2.093
2.129
2.165
2.202
2.238
2.274
2.310
2.346
2.382
2.418
2.454
2.490
2.526
2.562
2.598
2.635
2.671
2.707
2.743
2.779
2.815
2.851
2.887
2.923
2.959
2.996
3.032
3.068
3.104
3.140
3.176
3.212
3.248
3.284
3.320
3.356
3.392
3.429
3.465
3.501
3.537
3.573
3.609
IN./Hg MM/H2O
3.968
1372
4.041
1397
4.115
1422
4.188
1448
4.261
1473
4.335
1498
4.408
1524
4.483
1550
4.556
1575
4.630
1600
4.703
1626
4.776
1651
4.850
1676
4.923
1702
4.996
1727
5.070
1752
5.143
1778
5.216
1803
5.290
1828
5.365
1854
5.438
1880
5.511
1905
5.585
1930
5.658
1956
5.731
1981
5.805
2005
5.878
2032
5.951
2057
6.024
2082
6.100
2108
6.173
2134
6.246
2159
6.320
2184
6.393
2210
6.488
2235
6.540
2280
6.613
2286
6.686
2311
6.760
2336
6.833
2362
6.906
2387
6.981
2413
7.055
2438
7.128
2464
7.201
2489
7.275
2514
7.348
2540
CONVERSION FACTORS
P.S.I.
P.S.I.
P.S.I.
P.S.I.
P.S.I.
Note: Conversion Factors rounded.
MM/Hg
100.8
102.7
104.6
106.4
108.3
110.2
112.0
113.9
115.8
117.7
119.5
121.4
123.3
125.1
127.0
128.8
130.7
132.6
134.4
136.4
138.2
140.1
141.9
143.8
145.7
147.5
149.4
151.2
153.1
155.0
156.9
158.8
160.6
162.5
164.4
166.2
168.1
169.9
171.8
173.7
175.5
177.4
179.3
181.2
183.0
184.9
186.6
2
KG/CM
.1370
.1395
.1421
.1446
.1471
.1497
.1522
.1548
.1573
.1599
.1624
.1649
.1674
.1700
.1725
.1750
.1776
.1801
.1826
.1852
.1878
.1903
.1928
.1954
.1979
.2004
.2030
.2055
.2080
.2106
.2131
.2157
.2182
.2207
.2233
.2258
.2283
.2309
.2334
.2359
.2384
.2410
.2436
.2461
.2486
.2512
.2537
BAR MBAR
.1344 134.4
.1369 136.9
.1393 139.3
.1418 141.8
.1443 144.3
.1468 146.8
.1493 149.3
.1518 151.8
.1543 154.3
.1568 156.8
.1593 159.3
.1618 161.8
.1642 164.2
.1667 166.7
.1692 169.2
.1717 171.7
.1742 174.2
.1766 176.6
.1791 179.1
.1817 181.7
.1842 184.2
.1866 186.6
.1891 189.1
.1916 191.6
.1941 194.1
.1966 196.6
.1991 199.1
.2015 201.5
.2040 204.0
.2066 206.6
.2091 209.1
.2115 211.5
.2140 214.0
.2165 216.5
.2190 219.0
.2215 221.5
.2239 223.9
.2264 226.4
.2289 228.9
.2314 231.4
.2339 233.9
.2364 236.4
.2389 238.9
.2414 241.4
.2439 243.9
.2464 246.4
.2488 248.8
x 27.71 = in. H2O
x 2.036 = in. Hg
x 703.1 = mm/ H2O
x 51.75 = mm/Hg
2
x .0703 = kg/cm
P.S.I.
P.S.I.
P.S.I.
P.S.I.
PA
13438
13686
13934
14182
14431
14679
14927
15182
15430
15679
15927
16175
16423
16672
16920
17168
17416
17664
17912
18168
18416
18664
18912
19160
19409
19657
19905
20153
20402
20657
20905
21153
21401
21650
21898
22146
22394
22642
22890
23139
23387
23642
23890
24138
24387
24635
24883
KPA
13.44
13.69
13.93
14.18
14.43
14.68
14.93
15.18
15.43
15.68
15.93
16.18
16.42
16.67
16.92
17.17
17.42
17.66
17.91
18.17
18.42
18.66
18.91
19.16
19.41
19.66
19.90
20.15
20.40
20.66
20.90
21.15
21.40
21.65
21.90
22.15
22.39
22.64
22.89
23.14
23.39
23.64
23.89
24.14
24.39
24.64
24.88
x .0689 = bar
x 68.95 = mbar
x 6895 = Pa
x 6.895 = kPa
Pressure Conversion Chart, continued
P.S.I.
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3.0
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5.0
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
6.0
6.1
6.2
6.3
6.4
6.5
6.6
6.7
IN./H2O
27.71
30.45
33.22
35.98
38.75
41.52
44.29
47.06
49.82
52.59
55.36
58.13
60.90
63.67
66.43
69.20
71.97
74.74
77.51
80.27
83.04
85.81
88.58
91.35
94.11
96.88
99.65
102.4
105.2
108.0
110.7
113.5
116.3
119.0
121.8
124.6
127.3
130.1
132.9
135.6
138.4
141.2
143.9
146.7
149.5
152.2
155.0
157.8
160.5
163.3
166.1
168.8
171.6
174.4
177.2
179.9
182.7
185.5
IN./Hg
2.036
2.240
2.443
2.647
2.850
3.054
3.258
3.461
3.665
3.868
4.072
4.276
4.479
4.683
4.886
5.090
5.294
5.497
5.701
5.904
6.108
6.312
6.515
6.719
6.922
7.126
7.330
7.533
7.737
7.940
8.144
8.348
8.551
8.775
8.958
9.162
9.366
9.569
9.773
9.976
10.18
10.38
10.59
10.79
10.99
11.20
11.40
11.60
11.81
12.01
12.22
12.42
12.62
12.83
13.03
13.23
13.44
13.64
MM/H2O
703.1
773.4
843.7
914.0
984.3
1055
1125
1195
1256
1336
1406
1476
1547
1617
1687
1758
1828
1898
1969
2039
2109
2180
2250
2320
2390
2461
2531
2601
2672
2742
2812
2883
2953
3023
3094
2164
3234
3304
3375
3445
3515
3586
3656
3726
3797
3867
3937
4008
4078
4148
4218
4289
4359
4429
4500
4570
4640
4711
2
MM/Hg KG/CM
51.75
.0703
56.89
.0773
62.05
.0844
67.23
.0914
72.45
.0984
77.57
.1055
82.74
.1125
87.92
.1195
93.09
.1266
98.25
.1336
103.4
.1406
108.6
.1476
113.8
.1547
118.9
.1617
124.1
.1687
129.3
.1758
134.5
.1828
139.6
.1898
144.8
.1968
150.0
.2039
155.1
.2109
160.3
.2180
165.5
.2250
170.7
.2320
175.8
.2390
181.0
.2461
186.2
.2531
191.3
.2601
196.5
.2672
201.7
.2742
206.9
.2812
212.0
.2883
217.2
.2953
222.4
.3023
227.5
.3094
232.7
.3164
237.9
.3234
243.1
.3304
248.2
.3375
253.4
.3445
258.6
.3515
263.7
.3586
268.9
.3656
274.1
.3726
279.3
.3797
284.4
.3867
289.6
.3937
294.8
.4087
299.9
.4078
305.1
.4148
310.3
.4218
315.5
.4289
320.6
.4359
325.8
.4429
331.0
.4500
336.1
.4570
341.3
.4640
346.5
.4710
BAR
.0689
.0758
.0827
.0896
.0965
.1034
.1103
.1172
.1241
.1310
.1379
.1448
.1517
.1586
.1655
.1724
.1793
.1862
.1930
.1999
.2068
.2137
.2206
.2275
.2344
.2413
.2482
.2551
.2620
.2689
.2758
.2827
.2896
.2965
.3034
.3103
.3172
.3240
.3310
.3378
.3447
.3516
.3585
.3654
.3723
.3792
.3861
.3930
.3999
.4068
.4137
.4206
.4275
.4344
.4413
.4482
.4550
.4619
MBAR
68.95
75.84
82.74
89.63
96.52
103.4
110.3
117.2
124.1
131.0
137.9
144.8
151.7
158.6
165.5
172.4
179.3
186.2
193.0
199.9
206.8
213.7
220.6
227.5
234.4
241.3
248.2
255.1
262.0
268.9
275.8
282.7
289.6
296.5
303.4
310.3
317.2
324.0
331.0
337.8
344.7
351.6
358.5
365.4
372.3
379.2
386.1
393.0
399.9
406.8
413.7
420.6
427.5
434.4
441.3
448.2
455.0
461.9
PA
6895
7584
8274
8963
9652
10340
11030
11720
12410
13100
13790
14480
15170
15860
16550
17240
17930
18620
19300
19990
20680
21370
22060
22750
23440
24130
24820
25510
26200
26890
27580
28270
28960
29650
30338
31030
31720
32400
33100
33780
34470
35160
35850
36540
37230
37920
38610
39300
39990
40680
41370
42060
42750
43440
44130
44820
45500
46190
KPA
6.895
7.584
8.274
8.963
9.652
10.34
11.03
11.72
12.41
13.10
13.79
14.48
15.17
15.86
16.55
17.24
17.93
18.62
19.30
19.99
20.68
21.37
22.06
22.75
23.44
24.13
24.82
25.51
26.20
26.89
27.58
28.27
28.96
29.65
30.34
31.03
31.72
32.40
33.10
33.78
34.47
35.16
35.85
36.54
37.23
37.92
38.61
39.30
39.99
40.68
41.37
42.06
42.75
43.44
44.13
44.82
45.50
46.19
467
P.S.I.
6.8
6.9
7.0
7.1
7.2
7.3
7.4
7.5
7.6
7.8
8.0
8.2
8.4
8.6
8.8
9.0
9.2
9.4
9.6
9.8
10.0
11.0
12.0
13.0
14.0
14.7
15.0
16.0
17.0
18.0
19.0
20.0
21.0
22.0
23.0
24.0
25.0
IN./H2O
188.2
191.0
193.8
196.5
199.3
202.1
204.8
207.6
210.4
215.9
221.4
227.0
232.5
238.0
243.6
249.1
254.7
260.2
265.7
271.3
276.8
304.5
332.2
359.8
387.5
406.9
415.2
442.9
470.6
498.2
525.9
553.6
581.3
609.0
636.7
664.3
692.0
IN./Hg
13.84
14.05
14.25
14.46
14.66
14.86
15.07
15.27
15.47
15.88
16.29
16.70
17.10
17.51
17.92
18.32
18.73
19.14
19.54
19.95
20.36
22.40
24.43
26.47
28.50
29.93
30.54
32.58
34.61
36.65
38.68
40.72
42.76
44.79
46.83
48.86
50.90
MM/H2O MM/Hg KG/CM
4781
351.7
.4781
4851
356.8
.4851
4922
362.0
.4921
4992
367.2
.4992
5062
372.3
.5062
5132
377.5
.5132
5203
382.7
.5203
5273
387.9
.5273
5343
393.0
.5343
5484
403.4
.5484
5625
413.7
.5625
5765
424.1
.5765
5906
434.4
.5906
6047
444.7
.6046
6187
455.1
.6187
6328
465.4
.6328
6468
475.8
.6468
6609
486.1
.6609
6750
496.5
.6749
6890
506.8
.6890
7031
517.1
.7031
7734
568.9
.7734
8437
620.6
.8437
9140
672.3
.9140
9843
724.0
.9843
10340
760.2
1.033
10550
775.7
1.055
11250
827.4
1.125
11950
879.1
1.195
12660
938.9
1.265
13360
982.6
1.336
14060
1034
1.406
14770
1086
1.475
15470
1138
1.547
16170
1189
1.617
16870
1241
1.687
17580
1293
1.758
CONVERSION FACTORS
P.S.I.
P.S.I.
P.S.I.
P.S.I.
P.S.I.
Note: Conversion Factors rounded.
2
BAR
.4685
.4757
.4826
.4895
.4964
.5033
.5102
.5171
.5240
.5378
.5516
.5654
.5792
.5929
.6067
.6205
.6343
.6481
.6619
.6757
.6895
.7584
.8274
.8963
.9652
1.014
1.034
1.103
1.172
1.241
1.310
1.379
1.448
1.517
1.586
1.655
1.724
x 27.71 = in. H2O
x 2.036 = in. Hg
x 703.1 = mm/H2O
x 51.75 = mm/Hg
x .0703 = kg/cm2
MBAR
468.5
475.7
482.6
489.5
496.4
503.3
510.2
517.1
524.0
537.8
551.6
565.4
579.2
592.9
606.7
620.5
634.3
648.1
661.9
675.7
689.5
758.4
827.4
896.3
965.2
1014
1034
1103
1172
1241
1310
1379
1448
1517
1586
1655
1724
P.S.I.
P.S.I.
P.S.I.
P.S.I.
PA
46850
47570
48260
48950
49640
50330
51020
51710
52400
53780
55160
56540
57920
59290
60670
62050
63430
64810
66190
67570
68950
75840
82740
98630
96520
101400
103400
110300
117200
124100
131000
137900
144800
151700
153600
165500
172400
KPA
46.85
47.57
48.26
48.95
49.64
50.33
51.02
51.71
52.40
53.78
55.16
56.54
57.92
59.29
60.67
62.05
63.43
64.01
66.19
67.57
68.95
75.84
82.74
89.83
96.52
101.4
103.4
110.3
117.2
124.1
131.0
137.9
144.8
151.7
158.6
165.5
172.4
x .0689 = bar
x 68.95 = mbar
x 6895 = Pa
x 6.895 = kPa
Conversion Factors
MULTIPLY . . . . . . . . . . . .
Atmospheres . . . . . . . . . .
atm . . . . . . . . . . . . . . . . .
atm . . . . . . . . . . . . . . . . .
atm . . . . . . . . . . . . . . . . .
atm . . . . . . . . . . . . . . . . .
atm . . . . . . . . . . . . . . . . .
Barrels-Oil . . . . . . . . . . . .
BT Units . . . . . . . . . . . . . .
BTU’s. . . . . . . . . . . . . . . .
BTU’s. . . . . . . . . . . . . . . .
BTU’s. . . . . . . . . . . . . . . .
BTU’s . . . . . . . . . . . . . . .
BTU Min . . . . . . . . . . . . . .
BTU/min . . . . . . . . . . . . .
BTU/min . . . . . . . . . . . . .
BTU/min . . . . . . . . . . . . .
Centimeters . . . . . . . . . . .
cm . . . . . . . . . . . . . . . . . .
cm . . . . . . . . . . . . . . . . . .
Cms Mercury . . . . . . . . . .
cms Mercury . . . . . . . . . .
cms Mercury . . . . . . . . . .
cms Mercury . . . . . . . . . .
cms Mercury . . . . . . . . . .
Cms/Second. . . . . . . . . . .
cms/second . . . . . . . . . . .
cms/Second. . . . . . . . . . .
cms/Second. . . . . . . . . . .
cms/second . . . . . . . . . . .
cms/Second. . . . . . . . . . .
Cms/Sec/Sec . . . . . . . . . .
Cubic Cms . . . . . . . . . . . .
cu cms. . . . . . . . . . . . . . .
cu cms. . . . . . . . . . . . . . .
cu cms. . . . . . . . . . . . . . .
cu cms. . . . . . . . . . . . . . .
cu cms. . . . . . . . . . . . . . .
cu cms. . . . . . . . . . . . . . .
cu cms. . . . . . . . . . . . . . .
Cubic Feet . . . . . . . . . . . .
cu ft . . . . . . . . . . . . . . . . .
cu ft . . . . . . . . . . . . . . . . .
cu ft . . . . . . . . . . . . . . . . .
cu ft . . . . . . . . . . . . . . . . .
cu ft . . . . . . . . . . . . . . . . .
cu ft . . . . . . . . . . . . . . . . .
cu ft . . . . . . . . . . . . . . . . .
Cu Ft/min . . . . . . . . . . . . .
cu ft/ min . . . . . . . . . . . . .
cu ft/min. . . . . . . . . . . . . .
cu ft/min. . . . . . . . . . . . . .
BY . . . . . . . . . . . . . .
76.0 . . . . . . . . . . . . .
29.92 . . . . . . . . . . . .
33.90 . . . . . . . . . . . .
1.0333 . . . . . . . . . . .
14.70 . . . . . . . . . . . .
1.058 . . . . . . . . . . . .
42. . . . . . . . . . . . . . .
0.2520 . . . . . . . . . . .
777.5 . . . . . . . . . . . .
3.927 x 10-4 . . . . . .
107.5 . . . . . . . . . . . .
2.928 x 10-4 . . . . . .
12.96 . . . . . . . . . . . .
0.2356 . . . . . . . . . . .
0.01757 . . . . . . . . . .
7.57 . . . . . . . . . . . . .
0.3937 . . . . . . . . . . .
0.01 . . . . . . . . . . . . .
10. . . . . . . . . . . . . . .
0.01316 . . . . . . . . . .
0.4461 . . . . . . . . . . .
136.0 . . . . . . . . . . . .
27.85 . . . . . . . . . . . .
0.1934 . . . . . . . . . . .
1.969 . . . . . . . . . . . .
0.03281 . . . . . . . . . .
0.036 . . . . . . . . . . . .
0.6 . . . . . . . . . . . . . .
0.02237 . . . . . . . . . .
3.728 x 10-4 . . . . . .
0.03281 . . . . . . . . . .
3.531 x 10-5 . . . . . .
6.102 x 10-2 . . . . . .
10-6 . . . . . . . . . . . . .
1.308 x 10-6 . . . . . .
2.642 x 10-4 . . . . . .
10-3 . . . . . . . . . . . . .
2.113 x 10-3 . . . . . .
1.057 x 10-3 . . . . . .
2.832 x 104 . . . . . . .
1728. . . . . . . . . . . . .
0.02832 . . . . . . . . . .
0.03704 . . . . . . . . . .
7.48052 . . . . . . . . . .
28.32 . . . . . . . . . . . .
59.84 . . . . . . . . . . . .
29.92 . . . . . . . . . . . .
472.0 . . . . . . . . . . . .
0.1247 . . . . . . . . . . .
0.4720 . . . . . . . . . . .
62.43 . . . . . . . . . . . .
OBTAIN
cms mercury
ins mercury
ft water
kgs/sq cm
lbs/sq in
tons/sq ft
gals-oil
kgs-calories
ft-lbs
hp-hrs
kg-meters
kw-hrs
ft-lbs/sec
hp
kw
watts
inches
meters
mm
atm
ft water
kgs/sq meter
lbs/sq ft
lbs/sq in
ft/min
ft/sec
km/hr
meters/min
miles/hr
miles/min
ft/sec/sec
cu ft
cu in
cu meters
cu yds
gals
liters
pints (liq)
quarts (liq)
cubic cms
cu inches
cu meters
cu yds
gals
liters
pints (liq)
quarts (liq)
cu cms/sec
gals/sec
liters/sec
lbs w/min
468
MULTIPLY . . . . . . . . . . .
Cu Ft/Sec . . . . . . . . . . .
cu ft/sec . . . . . . . . . . . .
Cu inches. . . . . . . . . . . .
cu ins. . . . . . . . . . . . . . .
cu ins. . . . . . . . . . . . . . .
cu ins. . . . . . . . . . . . . . .
cu ins. . . . . . . . . . . . . . .
cu ins. . . . . . . . . . . . . . .
cu ins. . . . . . . . . . . . . . .
cu ins. . . . . . . . . . . . . . .
Cu Meters. . . . . . . . . . .
cu M . . . . . . . . . . . . . . .
cu M . . . . . . . . . . . . . . .
cu M . . . . . . . . . . . . . . .
cu M . . . . . . . . . . . . . . .
cu M . . . . . . . . . . . . . . .
cu M . . . . . . . . . . . . . . .
cu M . . . . . . . . . . . . . . .
Cu Yards. . . . . . . . . . . .
cu yds . . . . . . . . . . . . . .
cu yds . . . . . . . . . . . . . .
cu yds . . . . . . . . . . . . . .
cu yds . . . . . . . . . . . . . .
cu yds . . . . . . . . . . . . . .
cu yds . . . . . . . . . . . . . .
cu yds . . . . . . . . . . . . . .
Decimeters . . . . . . . . . .
Degs (Angle) . . . . . . . . .
degs (angle) . . . . . . . . .
degs (angle) . . . . . . . . .
Degrees Sec . . . . . . . . .
degs/sec . . . . . . . . . . . .
degs/sec . . . . . . . . . . . .
Fathoms. . . . . . . . . . . . .
Feet. . . . . . . . . . . . . . . .
ft . . . . . . . . . . . . . . . . . .
ft . . . . . . . . . . . . . . . . . .
ft . . . . . . . . . . . . . . . . . .
Ft of Water . . . . . . . . . .
ft of w. . . . . . . . . . . . . . .
ft of w. . . . . . . . . . . . . . .
ft of w. . . . . . . . . . . . . . .
ft of w. . . . . . . . . . . . . . .
Feet/Min . . . . . . . . . . . .
ft/min . . . . . . . . . . . . . . .
ft/min . . . . . . . . . . . . . . .
ft/min . . . . . . . . . . . . . . .
ft/min . . . . . . . . . . . . . . .
Ft/Sec/Sec . . . . . . . . . . .
ft/sec/sec. . . . . . . . . . . .
BY. . . . . . . . . . . . . . . . .
0.646317. . . . . . . . . . . .
448.831. . . . . . . . . . . . .
16.39 . . . . . . . . . . . . . .
5.787 x 10-4 . . . . . . . . .
1.639 x 10-5 . . . . . . . . .
2.143 x 10-5 . . . . . . . . .
4.329 x 10-3 . . . . . . . . .
1.639 x 10-2 . . . . . . . . .
0.03463. . . . . . . . . . . . .
0.01732. . . . . . . . . . . . .
106 . . . . . . . . . . . . . . . .
35.31. . . . . . . . . . . . . . .
61.023. . . . . . . . . . . . . .
1.308. . . . . . . . . . . . . . .
264.2. . . . . . . . . . . . . . .
103 . . . . . . . . . . . . . . . .
2113 . . . . . . . . . . . . . . .
1057 . . . . . . . . . . . . . . .
7.646 x 105. . . . . . . . . .
27 . . . . . . . . . . . . . . . . .
46.656. . . . . . . . . . . . . .
0.7646. . . . . . . . . . . . . .
202.0. . . . . . . . . . . . . . .
764.6. . . . . . . . . . . . . . .
1616 . . . . . . . . . . . . . . .
807.9. . . . . . . . . . . . . . .
0.1. . . . . . . . . . . . . . . . .
60 . . . . . . . . . . . . . . . . .
0.01745. . . . . . . . . . . . .
3600 . . . . . . . . . . . . . . .
0.01745. . . . . . . . . . . . .
0.1667. . . . . . . . . . . . . .
0.002778. . . . . . . . . . . .
6..................
30.48. . . . . . . . . . . . . . .
12 . . . . . . . . . . . . . . . . .
0.3048. . . . . . . . . . . . . .
1/3. . . . . . . . . . . . . . . . .
0.02950. . . . . . . . . . . . .
0.8876. . . . . . . . . . . . . .
0.08048. . . . . . . . . . . . .
62.43. . . . . . . . . . . . . . .
0.4335. . . . . . . . . . . . . .
0.5080. . . . . . . . . . . . . .
0.01667. . . . . . . . . . . . .
0.01829. . . . . . . . . . . . .
0.3040. . . . . . . . . . . . . .
0.01136. . . . . . . . . . . . .
30.48. . . . . . . . . . . . . . .
0.3048. . . . . . . . . . . . . .
OBTAIN
Million gals/day
gals/min
cc
cu ft
cu meters
cu yds
gals
liters
pints (liq)
quarts (liq)
cc
cu ft
cu ins
cu yds
gals
liters
pints (liq)
quarts (liq)
cu cms
cu ft
cu ins
cu meters
gals
liters
pints (liq)
quarts (liq)
meters
minutes
radians
secs
radians/sec
revs/min
revs/sec
ft
cms
ins
meters
yds
atms
ins mercury
kgs/sq cm
lbs/sq ft
lbs/sq in
cms/sec
ft/sec
kms/hrs
Ms/min
miles/hr
cms/sec/sec
ms/sec/sec
Conversion Factors
MULTIPLY . . . . . . . . . . . . BY . . . . . . . . . . . . . . OBTAIN
Ft Pounds . . . . . . . . . . . . . 1.286 x 10-3. . . . . . . BTU’s
ft lbs . . . . . . . . . . . . . . . . . 5.050 x 10-7. . . . . . . hp-hrs
ft lbs . . . . . . . . . . . . . . . . . 3.241 x 10-4. . . . . . . kg-calories
ft lbs . . . . . . . . . . . . . . . . . 0.1383 . . . . . . . . . . . kg-meters
ft lbs . . . . . . . . . . . . . . . . . 3.766 x 10-7. . . . . . . kw-hrs
Ft-Lbs/Min. . . . . . . . . . . . . 1.286 x 10-3. . . . . . . BTUs/min
ft-lbs/min. . . . . . . . . . . . . . 0.01667 . . . . . . . . . . ft-lbs/sec
ft-lbs/min . . . . . . . . . . . . . 3.030 x 10-5. . . . . . . hp
ft-lbs/min . . . . . . . . . . . . . 3.241 x 10-4. . . . . . . kg-calories/min
ft-lbs/min . . . . . . . . . . . . . 2.260 x 10-5. . . . . . . kws
Ft-Lbs/Sec . . . . . . . . . . . . 7.717 x 10-3. . . . . . . BTUs/min
ft-lbs/sec . . . . . . . . . . . . . 1.818 x 10-3. . . . . . . hp
ft-lbs/sec . . . . . . . . . . . . . 1.945 x 10-2. . . . . . . kg-calories/min
ft-lbs/sec . . . . . . . . . . . . . 1.356 x 10-3. . . . . . . kws
Gallons. . . . . . . . . . . . . . . 3785. . . . . . . . . . . . . ccs
gals . . . . . . . . . . . . . . . . . 0.1337 . . . . . . . . . . . cu ft
gals . . . . . . . . . . . . . . . . . 231. . . . . . . . . . . . . . cu ins
gals . . . . . . . . . . . . . . . . . 3.784 x 10-3. . . . . . . cu meters
gals . . . . . . . . . . . . . . . . . 3.785 . . . . . . . . . . . . liters
gals . . . . . . . . . . . . . . . . . 8. . . . . . . . . . . . . . . . pints (liq)
gals . . . . . . . . . . . . . . . . . 4. . . . . . . . . . . . . . . . quarts (liq)
Gallons, Imp. . . . . . . . . . . 1.20095 . . . . . . . . . . US gals
Gallons, US. . . . . . . . . . . 0.83267 . . . . . . . . . . imp gals
Gallons Water . . . . . . . . . 8.3453 . . . . . . . . . . . lbs water
Gallons/Min . . . . . . . . . . . 2.228 x 10-3. . . . . . . cu ft/sec
gals/min . . . . . . . . . . . . . 0.06308 . . . . . . . . . . liter/sec
gals/min . . . . . . . . . . . . . 8.0208 . . . . . . . . . . . cu ft/hr
Gals Water/Min . . . . . . . . 6.0086 . . . . . . . . . . . tons water/24 hrs
Grams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . dynes
grams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . grains
grams . . . . . . . . . . . . . . . 10-3 . . . . . . . . . . . . . kgs
grams . . . . . . . . . . . . . . . 103. . . . . . . . . . . . . . milligrams
grams . . . . . . . . . . . . . . . 0.03527 . . . . . . . . . . ozs
grams . . . . . . . . . . . . . . . 0.03215 . . . . . . . . . . ozs (troy)
grams . . . . . . . . . . . . . . . 2.205 x 10-3. . . . . . . lbs
Grams/Cm . . . . . . . . . . . . 5.600 x 10-3. . . . . . . lbs/in
Grams/Cu Cm . . . . . . . . . 62.43 . . . . . . . . . . . . lbs/cu ft
grams/cu cm . . . . . . . . . . 0.03613 . . . . . . . . . . lbs/cu in
Grams/Liter . . . . . . . . . . . 58.417 . . . . . . . . . . . grains/gal
grams/liter . . . . . . . . . . . . 8.345 . . . . . . . . . . . . lbs/1000 gals
grams/liter . . . . . . . . . . . . 0.062427 . . . . . . . . . lbs/cu ft
grams/liter . . . . . . . . . . . . 1000. . . . . . . . . . . . . parts/million
Horsepower . . . . . . . . . . . 42.44 . . . . . . . . . . . . BTUs/min
hp . . . . . . . . . . . . . . . . . . 33.000 . . . . . . . . . . . ft-lbs/min
hp . . . . . . . . . . . . . . . . . . 550. . . . . . . . . . . . . . ft-lbs/sec
hp . . . . . . . . . . . . . . . . . . 1.014 . . . . . . . . . . . . hp (metric)
hp . . . . . . . . . . . . . . . . . . 10.70 . . . . . . . . . . . . kg-calories/min
hp . . . . . . . . . . . . . . . . . . 0.7457 . . . . . . . . . . . kws
hp . . . . . . . . . . . . . . . . . . 745.7 . . . . . . . . . . . . watts
469
MULTIPLY . . . . . . . . . . .
Hp-Hours . . . . . . . . . . . .
hp-hrs . . . . . . . . . . . . . .
hp-hrs . . . . . . . . . . . . . .
hp-hrs . . . . . . . . . . . . . .
hp-hrs . . . . . . . . . . . . . .
Inches . . . . . . . . . . . . . .
Ins Mercury . . . . . . . . . .
ins mercury . . . . . . . . . .
ins mercury . . . . . . . . . .
ins mercury . . . . . . . . . .
ins mercury . . . . . . . . . .
Ins of Water . . . . . . . . . .
ins of w . . . . . . . . . . . . .
ins of w . . . . . . . . . . . . .
ins of w . . . . . . . . . . . . .
ins of w . . . . . . . . . . . . .
ins of w . . . . . . . . . . . . .
Kilograms. . . . . . . . . . . .
kgs . . . . . . . . . . . . . . . .
kgs . . . . . . . . . . . . . . . .
kgs . . . . . . . . . . . . . . . .
Kgs/Sq Cm. . . . . . . . . . .
kgs/sq cm . . . . . . . . . . .
kgs/sq cm . . . . . . . . . . .
kgs/sq cm . . . . . . . . . . .
kgs/sq cm . . . . . . . . . . .
Kiloliters . . . . . . . . . . . . .
Kilometers . . . . . . . . . . .
kms . . . . . . . . . . . . . . . .
kms . . . . . . . . . . . . . . . .
kms . . . . . . . . . . . . . . . .
Kms Hr. . . . . . . . . . . . . .
kms hr . . . . . . . . . . . . . .
kms hr . . . . . . . . . . . . . .
kms hr . . . . . . . . . . . . . .
kms hr . . . . . . . . . . . . . .
Kms/Hr Sec . . . . . . . . . .
kms/hr sec . . . . . . . . . .
kms/hr sec . . . . . . . . . .
Kilowatts. . . . . . . . . . . . .
kws . . . . . . . . . . . . . . . .
kws . . . . . . . . . . . . . . . .
kws . . . . . . . . . . . . . . . .
kws . . . . . . . . . . . . . . . .
kws . . . . . . . . . . . . . . . .
Killowatt-Hrs. . . . . . . . . .
kw-hrs . . . . . . . . . . . . . .
kw-hrs . . . . . . . . . . . . . .
kw-hrs . . . . . . . . . . . . . .
kw-hrs . . . . . . . . . . . . . .
BY . . . . . . . . . . . . . . . .OBTAIN
2547. . . . . . . . . . . . . . BTUs
1.98 x 106 . . . . . . . . . .ft-lbs
641.7 . . . . . . . . . . . . . kg-calories
2.737 x 105 . . . . . . . . .kg-meters
0.7457 . . . . . . . . . . . . kw-hrs
2.540 . . . . . . . . . . . . . cms
0.03342 . . . . . . . . . . . atms
1.133 . . . . . . . . . . . . . ft water
0.03453 . . . . . . . . . . . kgs/sq cm
70.73 . . . . . . . . . . . . . lbs/sq ft
0.4912 . . . . . . . . . . . . lbs/sq in
0.002458 . . . . . . . . . . atms
0.07355 . . . . . . . . . . . ins mercury
0.002540 . . . . . . . . . . kgs/sq cm
0.5781 . . . . . . . . . . . . ozs/sq in
5.202 . . . . . . . . . . . . . lbs/sq ft
0.03613 . . . . . . . . . . . lbs/sq in
980.665 . . . . . . . . . . . dynes
2.205 . . . . . . . . . . . . . lbs
1.102 x 10-3. . . . . . . . tons (short)
103. . . . . . . . . . . . . . . grams
0.9678 . . . . . . . . . . . . atms
32.81 . . . . . . . . . . . . . ft water
28.96 . . . . . . . . . . . . . ins mercury
20.48 . . . . . . . . . . . . . lbs/sq ft
14.22 . . . . . . . . . . . . . lbs/sq ft
103. . . . . . . . . . . . . . . Liters
105. . . . . . . . . . . . . . . Cms
3281. . . . . . . . . . . . . . Ft
103. . . . . . . . . . . . . . . Meters
0.6214 . . . . . . . . . . . . Miles
27.78 . . . . . . . . . . . . . cms/sec
54.68 . . . . . . . . . . . . . ft/min
0.9113 . . . . . . . . . . . . ft/sec
16.67 . . . . . . . . . . . . . meters/min
0.6214 . . . . . . . . . . . . miles/hr
27.78 . . . . . . . . . . . . . cms/sec/sec
0.9113 . . . . . . . . . . . . ft/sec/sec
0.2778 . . . . . . . . . . . . Ms/sec/sec
56.92 . . . . . . . . . . . . . BTUs/min
4.425 x 104 . . . . . . . . .ft-lbs/min
737.6 . . . . . . . . . . . . . ft-lbs/sec
1.341 . . . . . . . . . . . . . hp
14.34 . . . . . . . . . . . . . kg-calories/min
103. . . . . . . . . . . . . . . watts
3415. . . . . . . . . . . . . . BTUs
2.6655 x 106 . . . . . . . .ft-lbs
1.341 . . . . . . . . . . . . . hp-hours
860.5 . . . . . . . . . . . . . kg-calories
3.671 x 105 . . . . . . . . .kg-meters
Conversion Factors
MULTIPLY . . . . . . . . . . . . BY . . . . . . . . . . . . . . OBTAIN
Liters. . . . . . . . . . . . . . . . . 103. . . . . . . . . . . . . . ccs
liters. . . . . . . . . . . . . . . . . 0.03531 . . . . . . . . . . cu ft
liters. . . . . . . . . . . . . . . . . 61.02 . . . . . . . . . . . . cu ins
liters. . . . . . . . . . . . . . . . . 10-2 . . . . . . . . . . . . . cu meters
liters. . . . . . . . . . . . . . . . . 0.2642 . . . . . . . . . . . gals
liters. . . . . . . . . . . . . . . . . 1.057 . . . . . . . . . . . . quarts (liq)
Liters/min . . . . . . . . . . . . . 4.403 x 10-3. . . . . . . gals/sec
Meters . . . . . . . . . . . . . . . 100. . . . . . . . . . . . . . cms
meters . . . . . . . . . . . . . . . 3.281 . . . . . . . . . . . . ft
meters . . . . . . . . . . . . . . . 39.37 . . . . . . . . . . . . ins
meters . . . . . . . . . . . . . . . 10-3 . . . . . . . . . . . . . kms
meters . . . . . . . . . . . . . . . 103. . . . . . . . . . . . . . mms
Meters/Min . . . . . . . . . . . . 1.667 . . . . . . . . . . . . cms/sec
meters/min . . . . . . . . . . . 3.281 . . . . . . . . . . . . ft/min
meters/min . . . . . . . . . . . 0.05468 . . . . . . . . . . ft/sec
meters/min . . . . . . . . . . . 0.06 . . . . . . . . . . . . . kms/hr
meters/min . . . . . . . . . . . 0.03728 . . . . . . . . . . miles/hr
Meters/Sec . . . . . . . . . . . . 196.8 . . . . . . . . . . . . ft/min
meters/sec. . . . . . . . . . . . 3.281 . . . . . . . . . . . . ft/sec
meters/sec. . . . . . . . . . . . 3.6 . . . . . . . . . . . . . . kms/hr
meters/sec. . . . . . . . . . . . 0.06 . . . . . . . . . . . . . kms/min
meters/sec. . . . . . . . . . . . 2.237 . . . . . . . . . . . . miles/hr
meters/sec. . . . . . . . . . . . 0.03728 . . . . . . . . . . miles/min
Microns. . . . . . . . . . . . . . . 10-6 . . . . . . . . . . . . . meters
Microns. . . . . . . . . . . . . . . 25.400 . . . . . . . . . . . in
Miles/Hr . . . . . . . . . . . . . . 44.70 . . . . . . . . . . . . cms/sec
miles/hr . . . . . . . . . . . . . . 88. . . . . . . . . . . . . . . ft/min
miles/hr . . . . . . . . . . . . . . 1.467 . . . . . . . . . . . . ft/sec
miles/hr . . . . . . . . . . . . . . 1.609 . . . . . . . . . . . . kms/hr
miles/hr . . . . . . . . . . . . . . 0.8684 . . . . . . . . . . . knots
miles/hr . . . . . . . . . . . . . . 26.82 . . . . . . . . . . . . meters/min
Millimeters. . . . . . . . . . . . . 0.1 . . . . . . . . . . . . . . cms
mms. . . . . . . . . . . . . . . . . 0.03937 . . . . . . . . . . ins
Mins (Angle) . . . . . . . . . . . 2.909 x 10-4. . . . . . . radians
Ounces. . . . . . . . . . . . . . . 16. . . . . . . . . . . . . . . drams
ozs. . . . . . . . . . . . . . . . . . 437.5 . . . . . . . . . . . . grains
ozs. . . . . . . . . . . . . . . . . . 0.0625 . . . . . . . . . . . lbs
ozs. . . . . . . . . . . . . . . . . . 28.349527 . . . . . . . . grams
ozs. . . . . . . . . . . . . . . . . . 0.9115 . . . . . . . . . . . ozs (troy)
ozs. . . . . . . . . . . . . . . . . . 2.790 x 10-5. . . . . . . tons (long)
ozs. . . . . . . . . . . . . . . . . . 2.835 x 10-5. . . . . . . tons (metric)
Ozs (Fluid) . . . . . . . . . . . . 1.805 . . . . . . . . . . . . cu in
ozs (fluid). . . . . . . . . . . . . 0.02957 . . . . . . . . . . liters
Pounds. . . . . . . . . . . . . . . 16. . . . . . . . . . . . . . . ozs
lbs . . . . . . . . . . . . . . . . . . 256. . . . . . . . . . . . . . drams
lbs . . . . . . . . . . . . . . . . . . 7000. . . . . . . . . . . . . grains
lbs . . . . . . . . . . . . . . . . . . 0.0005 . . . . . . . . . . . tons (short)
lbs . . . . . . . . . . . . . . . . . . 453.5924 . . . . . . . . . grams
lbs . . . . . . . . . . . . . . . . . . 1.21528 . . . . . . . . . . lbs (troy)
lbs . . . . . . . . . . . . . . . . . . 14.5833 . . . . . . . . . . ozs (troy)
MULTIPLY . . . . . . . . . . BY . . . . . . . . . . . . . . . . OBTAIN
Lbs of Water . . . . . . . . . 0.01602 . . . . . . . . . . . . cu ft
lbs of water . . . . . . . . . 27.68 . . . . . . . . . . . . . . cu in
lbs of water . . . . . . . . . 0.1198 . . . . . . . . . . . . . gals
Lbs of w/Min . . . . . . . . . 2.679 x 10-4 . . . . . . . . . cu ft/sec
Pounds/Cu Ft . . . . . . . . 5.787 x 10-4 . . . . . . . . . lbs/cu in
Pounds/Cu In . . . . . . . . 1728 . . . . . . . . . . . . . . . lbs/cu ft
Pounds/Sq In . . . . . . . . 0.06804 . . . . . . . . . . . . atms
lbs/sq in . . . . . . . . . . . . 2.307 . . . . . . . . . . . . . . ft water
lbs/sq in . . . . . . . . . . . . 2.036 . . . . . . . . . . . . . . in mercury
lbs/sq in . . . . . . . . . . . . 0.07031 . . . . . . . . . . . . kgs/sq cm
Radians . . . . . . . . . . . . . 57.29578 . . . . . . . . . . . degrees
Tons (Long) . . . . . . . . . 1016 . . . . . . . . . . . . . . . kgs
tons (long) . . . . . . . . . . 2240 . . . . . . . . . . . . . . . lbs
tons (long) . . . . . . . . . . 1.12000 . . . . . . . . . . . . tons (short)
Tons (Short) . . . . . . . . . 2000 . . . . . . . . . . . . . . . lbs
tons (short) . . . . . . . . . 907.18486 . . . . . . . . . . kgs
tons (short) . . . . . . . . . 2430.56 . . . . . . . . . . . . lbs (troy)
tons (short) . . . . . . . . . 0.89287 . . . . . . . . . . . . tons (long)
tons (short) . . . . . . . . . 29166.66 . . . . . . . . . . . ozs (troy)
tons (short) . . . . . . . . . 0.90718 . . . . . . . . . . . . tons (metric)
Watts . . . . . . . . . . . . . . 0.05692 . . . . . . . . . . . . BTUs/min
watts . . . . . . . . . . . . . . 44.26 . . . . . . . . . . . . . . ft-lbs/min
watts . . . . . . . . . . . . . . 0.7376 . . . . . . . . . . . . . ft-lbs/sec
watts . . . . . . . . . . . . . . 1.341 x 10-3 . . . . . . . . . hp
watts . . . . . . . . . . . . . . 0.01434 . . . . . . . . . . . . kg-calories/min
watts . . . . . . . . . . . . . . 10-3 . . . . . . . . . . . . . . . kws
Watt-Hours . . . . . . . . . . 3.415 . . . . . . . . . . . . . . BTUs
watt-hrs . . . . . . . . . . . . 2655 . . . . . . . . . . . . . . . ft-lbs
watt-hrs . . . . . . . . . . . . 1.341 x 10-3 . . . . . . . . . hp-hrs
watt-hrs . . . . . . . . . . . . 0.8605 . . . . . . . . . . . . . kg-calories
watt-hrs . . . . . . . . . . . . 367.1 . . . . . . . . . . . . . . kg-meters
watt-hrs . . . . . . . . . . . . 10-3 . . . . . . . . . . . . . . . kw-hrs
470
Formulas—Electrical
Amps x Ohms
Volts
Ohm
Volts x Amps
Volts
Amps
Power Factor =
VOLTS =
Watts
Amps
Typical Ampere Wire Ratings*
Watts x Ohms
AMPS =
Watts
Volts
Watts
Ohms
WATTS =
2
Amps x Ohms
OHMS =
2
Volts
Watts
2
Volts
Ohms
Watts
2
Amps
KW = Cos θ
KVA
Single Phase
Three Phase
KW = A x PF
1000
3 x V x A x PF
1000
KVA = V x A
1000
Amps =
AWG MCM
3 xV xA
1000
KVA x 1000
V
KVA x 1000
3 xV
3 = 1.73
Approx. Motor KVA = Motor Horsepower (At Full Load)
C1+ C2+ C3 = C Total
Capacitors Connected in Parallel
Capacitors Connected in Series
For Two
More Than Two
= C Total
1
C1 x C2 = C Total
C1 x C 2
1 + 1 + 1
C2 C2 C2
VOLTAGE UNBALANCE
% Voltage Unbalance =
100 x Max. Voltage Deviation from Average Voltage
Average Voltage
V2
V1
BOOST TRANS.:
Rating Plate F.L.A. x Rating Plate VOLTS = KVA
= FACTOR
Rating Plate VOLTS
Rating Plate VOLTS - Norm. Line VOLT
KVA = Trans. KVA Rating
FACTOR
2 x Heater Rating = Rating @ New Voltage
V1 = Rated Volts
V2 = Measured Volts
14
12
10
8
6
4
3
2
1
1/0
2/0
3/0
4/0
250
300
350
400
500
600
700
750
800
900
1000
1250
1500
1750
2000
COPPER CONDUCTORS, IN CONDUIT*
TEMP. RATING OF CONDUCTOR*
60°C*
75°C*
90°C*
15
15
25°
20
20
30°
30
30
40°
40
45
50
55
65
70
70
85
90
80
100
105
95
115
120
110
130
140
155
150
125
185
175
145
210
200
165
195
230
235
215
255
270
240
285
300
260
310
325
280
335
360
320
380
405
355
420
455
385
460
490
400
475
500
410
490
515
435
520
555
455
545
585
495
590
645
520
625
700
545
650
735
560
665
775
*Summary only, refer to NEC 310-16, -17, -18, -19 (and others) for limitations.
Typical Electric Wire Size
MOTOR HP
1-1/3
1/2
3/4
1
1-1/2
2
3
5
7-1/2
10
SINGLE PH.
115 VOLT
230 VOLT
14
14
14
14
12
14
12
14
10
14
12
10
THREE PH.
230 VOLT
460 VOLT
14
14
14
14
14
14
12
10
8
14
14
14
14
14
14
14
14
12
From Standards of the National Board of Fire Underwriters.
Correction Table For
Watts - Amperes - Volts
471
WATTS
120
500
1000
1500
2000
2500
3000
4.2
8.3
12.5
16.7
20.9
25.0
VOLTAGE (C - SINGLE PHASE)
208
240
AMPERES
2.4
2.1
4.8
4.2
7.2
6.3
9.6
8.3
12.0
10.4
14.4
12.5
277
1.8
3.6
5.4
7.2
9.0
10.8
Electrical Units
Source: United States Bureau of Standards
The watt is the unit expressing electrical power as horsepower (hp) in mechanics; it is
equal to the product of the volts (pressure) times amperes (rate of flow). Thus, 2 volts
times 2 amperes would equal 4 watts in a direct current circuit. Electrical energy is sold
at so much per watt hour or more generally at a given amount per kilowatt hour - which
means 1,000 watt hours. This may represent 1 watt for 1,000 hours or 1,000 watts for
one hour. 746 watts are equal to one horsepower or inversely 1 kilowatt (kw) is equal to
about 1-1/2 horsepower.
Horsepower represents the power required to lift a weight of 33,000 lbs. 1 foot in 1
minute or 550 lbs. 1 foot in 1 second.
The ohm is the unit of electrical resistance and represents the physical property of a
conductor which offers a resistance to the flow of electricity, permitting just 1 ampere to
flow at 1 volt of pressure.
Formulas – Cooling Capacity*
Total BTUH = CFM x (THC1 – TCH2) x 4.5
TCH = Total Heat Content or Enthalpy (BTU. per lb. of air)
Sensible BTUH = CFM (T1 – T2) x 1.08
T = Dry Bulb Temp (Degrees Fahrenheit)
Latent BTUH = CFM (W 1 – W 2) x .683
W = Specific Humidity(Grains H2O per lb. of air)
(See Psychrometrics chart)
* Based on standard air at 13.3 cubic feet per lb.
Formulas—Heating Capacity *
BTUH = CFM x 1.08 x Rise
CFM = BTUH Output
1.08 x Rise
Rise = BTUH Output
1.08 x CFM
CFM = BTU/Hr. Input
1.35 x ∆T
Indoor Furnace 80%
CFM = BTU/Hr. Input
1.44 x ∆T
Outdoor Furnace 75%
CFM = KW x 3415
1.08 x ∆T
Electric Heat 92%
* Based on standard air at 13.3 cubic feet per lb.
Capacity Correction Factor
For correction of unit output, multiply the correction factor times the KWrating at 240
volts.
TR = 3160 x KW x VC
or
CFM = 3160 x KW x VC
CFM
TR
Where:
TR = temp. rise, F°
3160 = constant
KW = KW rating above
CFM = air flow at specified conditions
VC = heating correction factor
Formulas—General Subjects
3
Area of Circle = 0.7854 (Dia.)
Circumference of Circle = 3.14 x Dia.
2
Area of Sphere = 3.14 x (Dia.)
3
Volume of Sphere 0.524 x (Dia.)
Horsepower Conversion Chart
To convert decimal horsepower to commonly available fractional horsepower motors.
0.010
0.014
0.017
0.020
0.025
0.033
00.40
1/100
1/70
1/60
1/50
1/40
1/30
1/25
DECIMAL HORSEPOWER
0.050
0.067 0.083 0.100
0.125
FRACTIONAL HORSEPOWER
1/20
1/15
1/12
1/10
1/8
472
0.167
0.250
0.333
0.500
0.750
1.000
1/6
1/4
1/3
1/2
3/4
1
Typical Motor Ampere Values
SINGLE PHASE
NOMINAL
HORSEPOWER
1/6
1/4
1/3
1/2
3/4
1
1-1/2
2
3
5
7-1/2
10
15
20
25
30
40
50
60
75
100
125
150
200
115V
FLA
LRA
4.4
5.8
7.2
9.8
13.8
16
20
24
34
56
80
100
–
–
–
–
–
–
–
–
–
–
–
–
230V
58.8
82.8
96
120
144
204
336
480
600
–
–
–
–
–
–
–
–
–
–
–
–
FLA
2.2
2.9
3.6
4.9
6.9
8
10
12
17
28
40
50
–
–
–
–
–
–
–
–
–
–
–
–
230
LRA
FLA
LRA
29.4
41.4
48
60
72
102
168
240
300
–
–
–
–
–
–
–
–
–
–
–
–
–
–
2
2.8
3.6
5.2
6.8
9.6
15.2
22
28
42
54
68
80
104
130
154
192
248
312
360
480
–
–
–
12
16.8
21
30
39
54
90
132
162
240
312
384
468
624
750
900
1110
1476
1860
2160
2880
THREE PHASE
V460V
FLA
LRA
–
–
–
1
1.4
1.8
2.6
3.4
4.8
7.6
11
14
21
27
34
40
52
65
77
96
124
156
180
240
–
–
–
6
8.4
10.8
15
19.8
27
45
66
84
120
156
192
234
312
378
450
558
738
930
1080
1440
575V
FLA
LRA
–
–
–
0.8
1.1
1.4
2.1
2.7
3.9
6.1
9
11
17
22
27
32
41
52
62
77
99
125
144
192
–
–
–
4.8
6.6
8.4
12
15.6
24
36
54
66
96
126
156
186
246
300
360
444
588
744
864
1152
* Source: 1975 National Electrical Code. Tables 430-148, -150, -151. See applicable notes regarding 200V & 208V. Data presented as a guide only.
Insulation Factors
Use figure 1 to determine “R” value of walls, ceilings and floors. For walls that have more than one type of insulation, add the “R” values of each to obtain total “R”.
Example: Frame wall w/3" batt and 1" expanded Polyurethane.
473
Residential Duct Sizing Guide
Useful Data
The following duct sizes are based on a fraction drop of .10 inches per 100 feet of
lineal duct. This “Equal-Friction” method of duct sizing should be adequate for
normal residential furnace heating and air conditioning applications. Larger air
volumes or higher static pressures should be dealt with on an individual job basis.
Rectangular and Round Duct
AIR
VOLUME
50
75
100
125
150
175
200
225
250
275
300
400
500
600
700
800
900
1000
1100
1200
1300
1400
1500
1600
1700
1800
1900
2000
DUCT HEIGHT INCHES
6”
8”
10”
12”
4”
6X4
6X4
8X4
10 X 4
10 X 4
12 X 4
14 X 4
16 X 4
16 X 4
6X6
6X6
8X6
8X6
8X6
10 X 6
10 X 6
12 X 6
12 X 6
14 X 6
18 X 6
20 X 6
24 X 6
26 X 6
30 X 6
8X8
8X8
10 X 8
12 X 8
14 X 8
16 X 8
18 X 8
20 X 8
22 X 8
24 X 8
26 X 8
28 X 8
30 X 8
10 X
12 X
12 X
14 X
16 X
16 X
18 X
20 X
20 X
22 X
24 X
24 X
26 X
28 X
30 X
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
12 X
12 X
14 X
16 X
16 X
18 X
18 X
20 X
20 X
22 X
22 X
22 X
24 X
12
12
12
12
12
12
12
12
12
12
12
12
12
50
75
100
125
150
175
200
225
250
275
300
400
500
600
700
800
900
1000
1100
1200
1300
1400
1500
1600
1700
1800
1900
2000
Motor Pulley Diam. =
1" W.C. = .58 oz.
1.73" W.C. = 1 oz.
3.5" W.C. = 2 oz.
10.5" W.C. = 6.1oz.
27.71" W.C. = 1 lb.
Watts of Heat
1 Watt = 3.413 BTU.
BTU = Watts x 3.143
Formula For Figuring Capacity in
Gallons — Round Tanks
Multiply Square of the diameter in inches by .7854.Multiply
the result by length in inches, which will give you the volume
of tank in inches. Since there are 231 cubic inches in one
gallon you divide the inch volume by 231. The answer is
capacity in gallons.
ARI Conditions
(Air entering)
Evaporator 80°F DB / 67°F WB
Condenser 90°F DB
Motor RPM Motor Pulley Diam.
Driven Pulley Diam.
Driven Pulley Diam. x RPM
Motor RPM
Motor RPM = Driven Pulley Diam. x RPM
Motor Pulley Diam.
L = D + d x Π + 2x
2
Fuel oil/gal #1 = 135,800
#2 = 139,400
#3 = 141,800
Gas Cu/ft. Nat = 1150/950
Propane = 2,550
Gas Gallon Propane = 91,500
Butane = 102,600
Gas Pressure
(Inches of water to ounces)
Driven Pulley Diam. = Motor Pulley Diam. RPM
Driven Pulley RPM
Driven Pulley RPM =
Cooling 400 CFM Per Ton
Heating 12 CFM Per 1000 BTU Input
Approx. Heat Values: BTU’s
EQUIVALENT
AIR
ROUND
VOLUME
5
6
6
7
7
8
8
8
9
9
9
10
11
12
12
13
14
14
15
15
16
16
16
17
17
18
18
18
Nominal Air Flow
Where:
L = Length of Belt
D = Diameter of Large Pulley
d = Diameter of Small Pulley
x = Center to Center Distance
Π = 3.1416
474
Centrifugal Blower and Pump Laws
Capacity varies directly as speed
Pressure varies directly as (speed)2
Power varies directly as (speed)3
New CFM = Old CFM x New RPM
Old RPM
Pump HP =
New Static Pressure = Old Static Pressure x New RPM
Old RPM
New HP = Old HP x New RPM
Old RPM
3
Shaft HP = Ft.-Lbs. Torque x RPM
5250
2
GPM x Total Head
3960 x Pump Efficiency
New RPM = Present RPM x
New CFM
Present CFM
New SP = Present SP x
New CFM
Present CFM
New HP = Present HP x
New CFM
Present CFM
2
3
Tank Gauge Charts
275 GALLON
44” X 27” X 60”
VERTICAL
INCHES
GALLONS
2
5
4
14
6
25
8
37
10
50
12
65
14
79
16
93
18
107
20
122
22
136
24
150
26
164
28
178
30
193
32
207
34
221
36
234
38
246
40
258
42
268
44
275
275 GALLON
44” X 27” X 60”
HORIZONTAL
INCHES
GALLONS
2
14
4
32
6
51
8
73
10
96
12
118
14
146
16
169
18
191
20
213
22
235
24
253
26
275
285 GALLON
38” X 60”
INCHES
GALLONS
1
3
2
6
3
11
4
17
5
23
6
30
7
37
8
45
9
53
10
62
11
71
12
80
13
89
14
99
15
108
16
118
17
128
18
137
19
147
20
157
21
167
22
177
23
186
24
196
25
206
26
215
27
224
28
233
29
241
30
249
31
257
32
265
33
272
34
278
35
284
36
289
37
292
38
295
475
550 GALLON
48” X 72”
INCHES
GALLONS
1
3
2
8
3
15
4
22
5
31
6
41
7
51
8
62
9
73
10
85
11
97
12
110
13
123
14
137
15
151
16
165
17
179
18
193
19
208
20
222
21
237
22
252
23
267
24
282
25
297
26
312
27
327
28
342
29
356
30
371
31
385
32
399
33
413
34
427
35
441
36
454
37
467
38
479
39
491
40
502
41
513
42
523
43
533
44
542
45
549
46
556
47
561
48
564
1000 GALLON
48” X 128”
INCHES
GALLONS
1
5
2
14
3
26
4
40
5
55
6
72
7
91
8
110
9
130
10
151
11
173
12
196
13
219
14
243
15
267
16
292
17
317
18
343
19
369
20
395
21
421
22
447
23
474
24
501
25
528
26
555
27
581
28
607
29
633
30
659
31
685
32
710
33
735
34
759
35
783
36
806
37
829
38
851
39
872
40
892
41
911
42
930
43
947
44
962
45
976
46
988
47
997
48
1002
Enthalpy vs. Wetbulb
(Total heat content - BTU per lb. of air)
WET
BULB F
0
.1
.2
.3
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
13.01
13.44
13.87
14.32
14.77
15.23
15.70
16.17
16.66
17.15
17.65
18.16
18.68
19.21
19.75
20.30
20.86
21.44
22.02
22.61
23.22
23.84
24.48
25.12
25.78
26.46
27.15
27.85
28.57
29.31
30.06
30.83
31.62
32.42
33.25
34.09
34.95
35.83
36.74
37.66
38.61
39.57
40.57
41.58
42.62
43.69
44.78
45.90
47.04
48.22
49.43
13.05
13.48
13.92
14.36
14.82
15.28
15.74
16.22
16.71
17.20
17.70
18.21
18.73
19.26
19.81
20.36
20.92
21.49
22.08
22.68
23.28
23.90
24.54
25.19
25.85
26.53
27.22
27.92
28.64
29.38
30.14
30.91
31.70
32.50
33.33
34.18
35.04
35.92
36.83
37.75
38.71
39.67
40.67
41.68
42.73
43.80
44.89
46.01
47.16
48.34
49.55
13.09
13.52
13.96
14.41
14.86
15.32
15.79
16.27
16.75
17.25
17.75
18.26
18.79
19.32
19.86
20.41
20.98
21.55
22.14
22.74
23.34
23.97
24.61
25.25
25.92
26.60
27.29
27.99
28.72
29.46
30.21
30.99
31.78
32.59
33.42
34.26
35.13
36.01
36.92
37.85
38.80
39.77
40.77
41.79
42.83
43.91
45.00
46.13
47.28
48.46
49.68
13.14
13.57
14.01
14.45
14.91
15.37
15.84
16.32
16.80
17.30
17.80
18.32
18.84
19.37
19.92
20.47
21.03
21.61
22.20
22.80
23.41
24.03
24.67
25.32
25.98
26.67
27.36
28.07
28.79
29.53
30.29
31.07
31.86
32.67
33.50
34.35
35.21
36.10
37.02
37.94
38.90
39.87
40.87
41.89
42.94
44.02
45.12
46.24
47.39
48.58
49.80
TENTHS OF DEGREES
.4
.5
13.18
16.61
14.05
14.50
14.95
15.42
15.89
16.37
16.85
17.35
17.85
18.37
18.89
19.43
19.97
20.52
21.09
21.67
22.26
22.86
23.47
24.10
24.74
25.38
26.05
26.74
27.43
28.14
28.87
29.61
30.37
31.15
31.94
32.75
33.59
34.43
35.30
36.19
37.11
38.04
39.00
39.98
40.97
42.00
43.05
44.13
45.23
46.36
47.51
48.70
49.92
476
13.22
13.66
14.10
14.54
15.00
15.46
15.93
16.41
16.90
17.40
17.91
18.42
18.95
19.48
20.03
20.58
21.15
21.73
22.32
22.92
23.53
24.16
24.80
25.45
26.12
26.80
27.50
28.21
28.94
29.68
30.44
31.22
32.02
32.83
33.67
34.52
35.39
36.28
37.20
38.13
39.09
40.07
41.07
42.10
43.15
44.23
45.34
46.47
47.63
48.82
50.04
.6
.7
.8
.9
13.27
13.70
14.14
14.59
15.05
15.51
15.98
16.46
16.95
17.45
17.96
18.47
19.00
19.53
20.08
20.64
21.21
21.79
22.38
22.98
23.59
24.22
24.86
25.52
26.19
26.87
27.57
28.28
29.01
29.76
30.52
31.30
32.10
32.92
33.75
34.61
35.48
36.38
37.29
38.23
39.19
40.17
41.18
42.20
43.26
44.34
45.45
46.58
47.75
48.95
50.17
13.31
13.74
14.19
14.63
15.09
15.56
16.03
16.51
17.00
17.50
18.01
18.52
19.05
19.59
20.14
20.69
21.26
21.84
22.44
23.04
23.65
24.29
24.93
25.58
26.26
26.94
27.64
28.35
29.09
29.83
30.60
31.38
32.18
33.00
33.84
34.69
35.57
36.47
37.38
38.32
39.28
40.27
41.28
42.31
43.37
44.45
45.56
46.70
47.87
49.07
50.29
13.35
13.79
14.23
14.68
15.14
15.60
16.08
16.56
17.05
17.55
18.06
18.58
19.10
19.64
20.19
20.75
21.32
21.90
22.50
23.10
23.72
24.35
24.99
25.65
26.32
27.01
27.71
28.43
29.16
29.91
30.68
31.46
32.26
33.08
33.92
34.79
35.65
36.56
37.48
38.42
39.38
40.37
41.38
42.41
43.48
44.56
45.68
46.81
47.98
49.19
50.41
13.39
13.83
14.27
14.73
15.18
16.65
16.12
16.61
17.10
17.60
18.11
18.63
19.16
19.70
20.25
20.81
21.38
21.96
22.56
23.16
23.78
24.42
25.06
25.71
26.39
27.08
27.78
28.50
29.24
29.98
30.75
31.54
32.34
33.17
34.00
34.86
35.74
36.65
37.57
38.51
39.47
40.47
41.48
42.52
43.58
44.67
46.79
46.93
48.10
49.31
50.54
Drill Sizes
DRILL NUMBER
OR LETTER*
80
79
1/64
78
77
76
75
74
73
72
71
70
69
68
1/32
67
66
65
64
63
62
61
60
59
58
57
56
3/64
55
54
53
1/16
52
51
50
49
48
5/64
47
46
45
44
43
42
3/32
41
DECIMAL
EQUIV.
0.0135
0.0145
0.0156
0.016
0.018
0.020
0.021
0.0225
0.024
0.025
0.026
0.028
0.0292
0.031
0.0312
0.032
0.033
0.035
0.036
0.037
0.038
0.039
0.040
0.041
0.042
0.043
0.0465
0.0468
0.052
0.055
0.0595
0.0625
0.0635
0.067
0.070
0.073
0.076
0.0781
0.0785
0.081
0.082
0.086
0.089
0.0935
0.0937
0.096
DRILL NUMBER
OR LETTER*
40
39
38
37
36
7/64
35
34
33
32
31
1/8
30
29
28
9/64
27
26
25
24
23
5/32
22
21
20
19
18
11/64
17
16
15
14
13
3/16
12
11
10
9
8
7
13/64
6
5
4
3
7/32
DECIMAL
EQUIV.
0.098
0.0995
0.1015
0.104
0.1065
0.1094
0.110
0.111
0.113
0.116
0.120
0.1250
0.1285
0.136
0.1405
0.1406
0.144
0.147
0.1495
0.152
0.154
0.1562
0.157
0.159
0.161
0.166
0.1695
0.1719
0.173
0.177
0.180
0.182
0.185
0.1875
0.189
0.191
0.1935
0.196
0.199
0.201
0.2031
0.204
0.2055
0.209
0.213
0.2187
DRILL NUMBER
OR LETTER*
2
1
A
15/64
B
C
D
E & 1/4
F
G
17/64
H
I
J
K
9/32
L
M
19/64
N
5/16
O
P
21/64
Q
R
11/32
S
T
23/64
U
3/8
V
W
25/64
X
Y
13/32
Z
27/64
7/16
29/64
15/32
31/64
1/2
DECIMAL
EQUIV.
0.221
0.228
0.234
0.2344
0.238
0.242
0.246
0.250
0.257
0.261
0.2656
0.266
0.272
0.277
0.281
0.2812
0.290
0.295
0.2969
0.302
0.3125
0.316
0.323
0.3281
0.332
0.339
0.3437
0.348
0.358
0.3594
0.368
0.375
0.377
0.386
0.3906
0.397
0.404
0.4062
0.413
0.4219
0.4375
0.4531
0.4687
0.4844
0.5000
NOTE: The shank of a numbered drill makes a good gauge to determine the inside diameter of
capillary tubing or to measure gas burner orifices.
Unit Efficiency Ratings
EER is the industry standard in the United States for rating the efficiency of a commercial unit. On
some international specifications, however, minimum efficiencies are often listed in COP or
KW/TON. To convert our efficiency ratings from EER to COP or KW/TON, you can use the following
table:
EER
COP
KW/TON
9.0
2.64
1.33
10.0
2.93
1.20
11.0
3.22
1.09
12.0
3.52
1.00
13.0
3.81
0.92
14.0
4.10
0.86
Example for a unit with a net capacity of 100 MBH
and a total power requirement of 10 KW:
EER = 100 MBH = 10.0 MBH
10 KW
KW
COP (100 MBH 10 KW) = 2.93 (Note: 3.415 MBH = 1 KW)
3.415 MBH/KW
KW/TON = 10 KW x 12 MBH/TON 1.20 KW/TON (Note: 12 MBH = 1 TON)
100 MBH
477
Temperature Conversion
Fahrenheit And Centigrade
To convert Fahrenheit to Celsius (Centigrade)
.556 x (°F –32) = °C
To convert Celsius (Centigrade) to Fahrenheit
(°C x 1.8) +32 = °F
C°
F°
C°
F°
–30
–22
40
104
–25
–13
45
113
–20
–4
50
122
–15
5
55
131
–10
14
60
140
–5
23
65
149
0
32
70
158
5
41
75
167
10
50
80
176
15
59
85
185
20
68
90
194
25
77
95
203
30
86
100
212
35
95
105
221
APPROX. BTU, GRAVITY &
WEIGHT OF FUEL OIL
AVERAGE
BTU’S PER SPECIFIC
FUEL NO.
GAL.
GRAVITY
1
135,800
38-42
2
139,400
32-36
4
145,000
24-26
5
148,100
18-22
6
151,300
14-16
LBS. PER
GAL.
6.8
7.2
7.5
7.7
7.9
CAPACITIES OF
CYLINDRICAL TANKS
DIAMETER
INCHES
GALS. PER
IN. LENGTH
12”
15”
18”
24”
27”
30”
33”
36”
42”
48”
54”
60”
66”
72”
84”
96”
108”
120”
144”
.49
.76
1.10
1.95
2.47
3.06
3.70
4.40
5.99
7.83
9.91
12.24
14.81
17.63
23.99
31.33
39.66
48.96
70.50
GALS.
PER FT.
LENGTH
5.88
9.18
13.22
23.50
29.74
36.70
44.43
52.88
71.97
94.00
118.97
146.88
177.72
211.51
287.88
376.01
475.89
587.52
846.00
Airflow Versus Temperature Rise
AIRFLOW – CUBIC FEET PER MINUTE
HEAT
OUTPUT
KW BTU
3 10242
4 13656
5 17070
6 20484
7 23898
8 27312
9 30726
10 34140
11 37554
12 40968
13 44382
14 47796
15 51210
16 54624
17 58038
18 61452
19 64866
20 68280
21 71694
22 75108
23 78522
24 81936
25 85350
26 88764
27 92178
28 95592
29 99006
30 102420
400 500 600 700 800 900 1000 11001200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800 2900 3000 3100 3200 3300
TEMPERATURE RISE – DEGREES FAHRENHEIT
24
32
39
47
55
63
71
79
87
95
19
25
32
38
44
51
57
63
69
76
82
89
95
16
21
26
32
37
42
47
53
58
63
68
74
79
84
89
95
14
18
23
27
32
36
41
45
50
54
58
63
68
72
77
82
86
90
95
99
12
16
20
24
28
32
36
39
43
47
51
55
59
64
67
72
75
79
83
87
91
95
99
14
18
21
25
28
32
35
39
42
46
49
53
56
60
64
67
70
74
77
81
84
88
91
95
98
13
16
19
22
25
28
32
35
38
41
44
47
50
54
56
60
63
66
69
73
76
79
82
85
88
92
95
14
17
20
23
26
29
32
34
37
40
43
46
49
52
55
57
60
63
66
69
72
75
78
80
83
86
13
16
18
21
24
26
29
32
34
37
39
42
45
48
50
53
55
58
61
63
66
68
71
74
76
79
15
17
19
22
24
27
29
32
34
36
38
41
44
46
49
51
53
56
58
61
63
66
68
71
73
14
16
18
20
22
25
27
29
32
34
36
38
40
42
45
47
50
52
54
56
59
61
63
65
68
15
17
19
21
23
25
27
30
32
34
36
38
40
42
44
46
48
51
53
55
57
59
61
63
14
16
18
20
22
24
26
28
30
32
34
36
38
40
41
43
45
47
49
51
53
55
57
59
15
17
19
20
22
24
26
28
30
32
34
36
37
39
41
43
45
46
48
50
52
54
56
14
16
18
19
21
23
25
26
28
30
32
34
35
37
39
40
42
44
46
47
49
51
53
15
17
18
20
22
23
25
27
28
30
32
33
35
37
38
40
42
43
45
47
48
50
14
16
17
19
21
22
24
25
27
28
30
32
33
35
36
38
40
41
43
44
46
47
15
16
18
20
21
23
24
26
27
29
30
32
33
35
36
38
39
41
42
44
45
14
15
17
19
20
22
23
24
26
27
29
30
32
33
34
36
37
39
40
42
43
14
16
18
19
21
22
23
25
26
27
29
30
32
33
34
36
37
38
40
41
13
15
17
18
20
21
22
24
25
26
28
29
30
32
33
34
36
37
38
40
14
16
17
19
20
21
23
24
25
27
28
29
30
32
33
34
35
37
38
15
16
18
19
20
22
23
24
26
27
28
29
30
32
33
34
35
36
15
17
18
19
20
22
23
25
26
27
28
29
30
32
33
34
35
16
17
18
19
21
22
24
25
26
27
28
29
30
32
33
34
16
17
18
20
22
23
24
25
26
27
28
29
31
32
33
Decimal and Metric Equivalents
Equivalents of Common Fractions of An Inch
64THS
1/64
3/64
5/64
7/64
32NDS
16THS
8THS
1/32
1/16
3/32
1/8
9/64
11/64
13/64
15/64
5/32
3/16
7/32
1/4
17/64
19/64
9/32
5/16
21/64
23/64
25/64
27/64
11/32
3/8
13/32
7/16
29/64
31/64
15/32
1/2
DECIMAL
MM
0.01562
0.03125
0.04688
0.06250
0.07812
0.09375
0.10938
0.12500
0.14062
0.15625
0.17188
0.18750
0.20312
0.21875
0.23438
0.25000
0.26562
0.28125
0.29688
0.31250
0.32812
0.34375
0.35938
0.37500
0.39062
0.40625
0.42188
0.43750
0.45312
0.46875
0.48438
0.397
0.794
1.191
1.588
1.984
2.381
2.778
3.175
3.572
3.969
4.366
4.763
5.159
5.556
5.953
6.350
6.747
7.144
7.541
7.938
8.334
8.731
9.128
9.525
9.922
10.319
10.716
11.113
11.509
11.906
12.303
478
64THS
33/64
35/64
37/64
39/64
32NDS
16THS
8THS
17/32
9/16
19/32
5/8
41/64
43/64
45/64
47/64
21/32
11/16
23/32
3/4
49/64
51/64
25/32
13/16
53/64
55/64
57/64
59/64
27/32
7/8
29/32
15/16
61/64
63/64
31/32
1
DECIMAL
MM
0.51562
0.53125
0.54688
0.56250
0.57812
0.59375
0.60938
0.62500
0.64062
0.65625
0.67188
0.68750
0.70312
0.71875
0.73438
0.75000
0.76562
0.78125
0.79688
0.81250
0.82812
0.84375
0.85938
0.87500
0.89062
0.90625
0.92188
0.93750
0.95312
0.96875
0.98438
13.097
13.494
13.891
14.288
14.684
15.081
15.478
15.875
16.272
16.669
17.066
17.463
17.859
18.256
18.653
19.050
19.447
19.844
20.241
20.638
21.034
21.431
21.828
22.225
22.622
23.019
23.416
23.813
24.209
24.606
25.003
16
17
19
21
22
23
24
25
26
27
28
30
31
32
16
18
20
21
22
23
24
25
26
28
29
30
31
17
20
21
22
23
24
25
26
27
28
29
30
19
20
21
22
23
24
25
26
27
28
29
Sensor Resistance vs. Temperature
TEMP.
°F
RESIST.
(OHMS)
TEMP.
°F
RESIST.
(OHMS)
TEMP.
°F
RESIST.
(OHMS)
TEMP.
°F
RESIST.
(OHMS)
TEMP.
°F
RESIST.
(OHMS)
TEMP.
°F
RESIST.
(OHMS)
–10
–9
–8
–7
–6
–5
–4
–3
–2
–1
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
118,050
114,230
110,540
106,990
103,560
100,260
97,070
93,994
91,027
88,162
85,398
82,730
80,154
77,668
75,268
72,950
70,712
68,550
66,462
64,444
62,495
60,611
58,791
57,031
55,330
53,685
52,095
50,557
49,070
47,632
46,240
44,894
43,591
42,330
41,110
39,929
38,785
37,678
36,607
35,569
34,565
33,592
32,650
31,738
30,854
29,998
29,168
28,364
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
27,586
26,831
26,099
25,390
24,703
24,036
23,390
22,763
22,155
21,566
20,994
20,439
19,900
19,377
18,870
18,377
17,899
17,435
16,985
16,547
16,122
15,710
15,309
14,920
14,542
14,175
13,818
13,472
13,135
12,808
12,490
12,181
11,881
11,589
11,305
11,030
10,761
10,501
10,247
10,000
9,759
9,526
9,298
9,077
8,862
8,653
8,449
8,250
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
8,057
7,868
7,685
7,506
7,332
7,163
6,998
6,838
6,682
6,530
6,381
6,237
6,097
5,960
5,827
5,697
5,570
5,447
5,327
5,209
5,095
4,983
4,875
4,768
4,665
4,564
4,466
4,370
4,276
4,184
4,095
4,008
3,923
3,840
3,759
3,680
3,603
3,527
3,454
3,382
3,312
3,243
3,177
3,111
3,048
2,986
2,925
2,866
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
2,808
2,751
2,696
2,642
2,589
2,538
2,488
2,438
2,390
2,343
2,297
2,252
2,208
2,166
2,124
2,083
2,042
2,003
1,965
1,927
1,891
1,855
1,820
1,785
1,752
1,719
1,686
1,655
1,624
1,593
1,564
1,535
1,506
1,479
1,451
1,425
1,399
1,374
1,349
1,324
1,301
1,277
1,255
1,232
1,210
1,189
1,168
1,148
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
1,128
1,108
1,089
1,070
1,051
1,033
1,015
997
980
963
947
931
915
899
884
869
855
841
827
813
799
786
773
761
748
736
724
712
700
689
678
667
656
646
635
625
615
606
596
587
578
569
560
551
542
534
526
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
518
510
502
494
487
479
472
465
458
451
445
438
431
425
419
412
406
400
395
389
383
378
372
367
361
356
351
346
341
336
332
327
322
318
313
309
305
300
296
292
288
284
280
276
273
269
265
479
Temperature/Pressure Tables
TEMP.
F°
–50
–48
–46
–44
–42
–40
–38
–36
–34
–32
–30
–28
–26
–24
–22
–20
–18
–16
–14
–12
–10
–8
–6
–4
–2
0
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
11
28.9
28.8
28.7
28.6
28.5
28.4
28.3
28.2
28.1
27.9
27.8
27.7
27.5
27.4
27.2
27.0
26.8
26.6
26.4
26.2
26.0
25.8
25.5
25.3
25.0
24.7
24.4
24.1
23.8
23.4
23.1
22.7
22.3
21.9
21.5
21.1
20.6
20.1
19.7
19.1
18.6
18.1
17.5
16.9
16.3
15.6
15.0
14.3
13.6
12.8
12.0
11.2
10.4
9.6
8.7
7.8
6.8
5.9
4.9
3.8
2.8
1.6
134A
18.5
17.7
17.0
16.2
15.5
14.7
13.7
12.7
11.7
10.8
9.8
8.6
7.4
6.2
5.0
3.8
3.4
3.0
2.6
2.2
1.8
2.7
3.6
4.5
5.4
6.3
7.4
8.4
9.5
10.5
11.6
12.9
14.2
15.4
16.7
18.0
19.5
21.0
22.5
24.1
25.6
27.4
29.2
30.9
32.7
34.5
36.6
38.7
40.7
42.8
44.9
47.3
49.7
52.1
54.5
56.9
59.7
62.4
65.2
67.9
70.7
73.8
REFRIGERANTS
12
22
500
15.4
6.2
12.8
14.6
4.8
11.9
13.8
3.5
10.9
12.9
2.0
9.8
11.9
.5
8.8
11.0
.5
7.6
10.0
1.3
6.4
8.9
2.2
5.2
7.8
2.0
3.9
6.7
3.9
2.6
5.5
4.9
1.2
4.3
5.9
.1
3.0
6.9
.9
1.6
7.9
1.6
.3
9.0
2.4
.6
10.2
3.2
1.3
11.3
4.1
2.1
12.5
5.0
2.8
13.8
5.9
3.7
15.1
6.8
4.5
16.5
7.8
5.4
17.9
8.8
6.3
19.3
9.9
7.2
20.8
11.0
8.2
22.4
12.1
9.2
24.0
13.3
10.2
25.6
14.5
11.2
27.3
15.7
12.3
29.1
17.0
13.5
30.9
18.4
14.6
32.8
19.7
15.8
34.7
21.2
17.1
36.7
22.6
18.4
38.7
24.1
19.7
40.9
25.7
21.0
43.0
27.3
22.4
45.3
28.9
23.9
47.6
30.6
25.4
50.0
32.4
26.9
52.4
34.2
28.5
54.9
36.0
30.1
57.5
37.9
31.7
60.1
39.9
33.4
62.8
41.9
35.2
65.6
43.9
37.0
68.5
46.1
38.8
71.5
48.2
40.7
74.5
50.5
42.7
77.6
52.8
44.7
80.8
55.1
46.7
84.0
57.6
48.8
87.4
60.1
51.0
90.8
62.6
53.2
94.3
65.2
55.4
97.9
67.9
57.7
101.6
70.6
60.1
105.4
73.5
62.5
109.3
76.3
65.0
113.2
79.3
67.6
117.3
82.3
70.2
121.4
85.4
72.9
125.7
88.6
502
.0
.8
1.6
2.5
3.4
4.3
5.2
6.2
7.2
8.3
9.4
10.5
11.7
13.0
14.2
15.5
16.9
18.3
19.7
21.2
22.8
24.4
26.0
27.7
29.4
31.2
33.1
35.0
37.0
39.0
41.1
43.2
45.5
47.7
50.1
52.5
54.9
57.4
60.0
62.7
65.4
68.2
71.1
74.1
77.1
80.2
83.4
86.6
90.0
93.4
96.9
100.5
104.1
107.9
111.7
115.6
119.6
123.7
127.9
132.2
136.6
141.1
717
14.3
13.3
12.2
11.1
10.0
8.7
7.4
6.1
4.7
3.2
1.6
.0
.8
1.7
2.6
3.6
4.6
5.6
6.7
7.9
9.0
10.3
11.6
12.9
14.3
15.7
17.2
18.8
20.4
22.1
23.8
25.6
27.5
29.4
31.4
33.5
35.7
37.9
40.2
42.6
45.0
47.6
50.2
52.9
55.7
58.6
61.6
64.7
67.9
71.1
74.5
78.0
81.5
85.2
89.0
92.9
96.9
101.0
105.3
109.6
114.1
118.7
480
TEMP.
F°
76
78
80
82
84
86
88
90
92
94
96
98
100
102
104
106
108
110
112
114
116
118
120
122
124
126
128
130
132
134
136
138
140
142
144
146
148
150
152
154
156
158
160
162
164
166
168
170
172
174
176
178
180
182
184
186
188
190
192
194
196
198
11
.3
.9
1.5
2.2
2.8
3.5
4.2
4.9
5.6
6.3
7.1
7.9
8.8
9.6
10.5
11.3
12.3
13.2
14.2
15.1
16.1
17.2
18.2
19.3
20.5
21.6
22.8
24.0
25.2
26.5
27.8
29.1
30.4
31.8
33.2
34.7
36.2
37.7
39.2
40.8
42.4
44.1
45.8
47.5
49.2
51.0
52.9
54.8
56.8
58.8
60.7
62.7
64.7
66.9
69.1
71.3
73.5
75.7
78.1
80.5
83.0
85.4
134A
80.1
83.3
86.4
90.0
93.5
97.1
100.6
104.2
108.2
112.2
116.3
120.3
124.3
128.8
133.3
137.8
142.3
146.8
151.8
156.8
161.9
166.9
171.9
177.5
183.1
188.6
194.2
199.8
205.9
212.1
218.2
224.4
230.5
237.3
244.1
250.1
257.6
264.4
271.8
279.2
286.7
294.1
301.5
309.6
317.7
325.8
333.9
342.0
350.8
359.6
368.3
377.1
385.9
395.4
405.0
414.5
424.1
433.6
443.9
454.2
464.4
474.7
REFRIGERANTS
12
22
500
78.4
134.5
95.1
81.3
139.0
98.5
84.2
143.6
102.0
87.2
148.4
105.6
90.2
153.2
109.2
93.3
158.2
112.9
96.5
163.2
116.7
99.8
168.4
120.6
103.1
173.7
124.5
106.5
179.1
128.6
110.0
184.6
132.7
113.5
190.2
136.9
117.2
195.9
141.2
120.9
201.8
145.6
124.6
207.7
150.1
128.5
213.8
154.7
132.4
220.0
159.4
136.4
226.4
164.1
140.5
232.8
169.0
144.7
239.4
173.9
148.9
246.1
179.0
153.2
252.9
184.2
157.7
259.9
189.4
162.2
267.0
194.8
166.7
274.3
200.2
171.4
281.6
205.8
176.2
289.1
211.5
181.0
296.8
217.2
185.9
304.6
223.1
191.0
312.5
229.1
196.1
320.6
235.2
201.3
328.9
241.4
206.6
337.3
247.7
212.0
345.8
254.2
217.5
354.5
260.7
223.1
363.3
267.4
228.8
372.3
274.2
234.6
381.5
281.1
240.5
390.8
288.1
246.5
400.3
295.3
252.6
410.0
302.5
258.8
419.8
309.9
265.1
429.8
317.4
271.5
440.0
325.1
278.1
450.4
332.9
284.7
460.9
340.8
291.5
471.7
348.8
298.3
482.6
357.0
305.3
493.7
365.3
312.4
505.0
373.7
319.6
516.5
382.3
326.9
528.2
391.0
334.3
540.1
399.9
341.9
552.2
408.8
349.5
564.5
418.0
357.3
577.1
327.3
365.2
589.9
436.7
373.3
602.9
446.3
381.4
616.1
456.0
389.7
629.6
465.9
398.2
643.4
475.9
406.7
657.4
486.1
502
150.3
155.1
159.9
164.9
170.0
175.1
180.4
185.8
191.3
196.9
202.6
208.4
214.4
220.4
226.6
232.9
239.3
245.8
252.4
259.2
266.1
273.1
280.3
287.5
295.0
302.5
310.2
318.0
325.9
334.0
342.3
350.6
359.1
367.8
376.6
385.6
394.7
403.9
413.4
422.9
432.7
442.5
452.6
717
128.3
133.2
138.3
143.6
149.0
154.5
160.1
165.9
171.9
178.0
184.2
190.6
197.2
203.9
210.7
217.8
225.0
232.3
239.8
247.5
255.4
263.5
271.7
280.1
288.7
Capillary Tube Length Conversion Chart
Enables users of capillary tubing to use the more prevalent tubing sizes which are readily available. While many original equipment manufacturers
and condensing unit manufacturers recommend specific lengths and diameters of capillary tubing for their units, these tube sizes are not always
readily available except on special order. This conversion chart enables the user to translate the recommended length into a tube diameter that can
be quickly obtained. In using the chart it is recommended that conversions be made using factors within the unshadedarea.
To Use Chart
(1) Locate original cap tube I.D. in left handcolumn.
(2) Read across and find conversion factor under New I.D. cap tube size. Conversion factors in unshaded area show range of new I.D. Cap. Tubes
recommended.
(3) Multiply the length of the original cap tube by the conversion factor.
(4) The resultant length of cap tube will approximate the same flow characteristics as the original cap tube.
Example
Original cap tube: .055" I.D. x 65"
Locate .055 in left hand column and read across in unshaded areas to locate the conversion factors. Multiply the original cap tube length, (65"), by
the conversion factors to get the correct length for the new I.D.
NEW I.D.
FACTOR
LENGTH
.049
.050
.054
.055
.059
.59
.64
.92
1.00
1.38
38.4”
41.6"
59.8"
65.0"
89.7"
Any of these cap tubes will approximate the same results as the original cap tube.
Capillary Tube Length Conversion Chart NEW ID
ORIG. ID
.035
.036
.037
.038
.039
.040
.041
.042
.043
.044
.045
.046
.047
.048
.049
.050
.051
.052
.053
.054
.055
.056
.057
.058
.059
.060
.064
.070
.075
.080
.085
.090
.095
.100
.105
.110
.115
.120
.042
2.31
2.10
1.79
1.59
1.41
1.25
1.12
1.00
.87
.81
.73
.67
.59
.54
.49
.45
.41
.044
2.22
1.92
1.75
1.55
1.38
1.24
1.11
1.00
.90
.82
.74
.67
.61
.56
.51
.47
.43
.39
.36
.049
2.51
2.26
2.03
1.83
1.62
1.47
1.34
1.20
1.10
1.00
.91
.84
.76
.69
.65
.59
.54
.50
.46
.42
.39
.050
2.50
2.23
1.98
1.79
1.60
1.47
1.31
1.20
1.09
1.00
.93
.85
.78
.70
.64
.60
.55
.51
.47
.43
.32
.054
.055
.059
2.32
2.08
1.89
1.72
1.55
1.43
1.31
1.19
1.09
1.00
.92
.85
.79
.73
.67
.62
.47
.30
2.27
2.06
1.87
1.69
1.56
1.44
1.32
1.20
1.09
1.00
.94
.87
.80
.73
.67
.50
.33
2.14
1.96
1.78
1.64
1.52
1.38
1.27
1.17
1.07
1.00
.93
.69
.46
481
.064
2.18
2.00
1.85
1.72
1.56
1.44
1.33
1.00
.67
.48
.070
2.18
2.04
1.50
1.00
.73
.54
.075
2.07
1.37
1.00
.74
.57
.43
.080
1.84
1.37
1.00
.76
.62
.46
.085
1.75
1.32
1.00
.76
.60
.48
.090
1.71
1.29
1.00
.79
.62
.49
.100
1.62
1.27
1.00
.80
.65
.53
.43
Formed Cap Tubes To Recommended Unformed Cap Tubes
FORMED
RECOMMENDED
CAPILLARY TUBE CAPILLARY TUBE
ID
OD LENGTH
FORMED
RECOMMENDED
ID
OD LENGTH
FORMED
RECOMMENDED
ID
OD
LENGTH
062-39619-000
062-39620-000
062-39621-000
062-39622-000
062-47192-000
062-47193-000
062-47194-000
062-50245-000
062-50246-000
062-50247-000
062-50248-000
062-50249-000
062-50250-000
007-03966-000
007-03966-000
007-03966-000
007-03966-000
007-03838-000
007-03838-000
007-03838-000
007-02806-000
007-02806-000
007-02806-000
007-02806-000
007-02806-000
007-02806-000
.064
.064
.064
.064
.054
.054
.054
.080
.080
.080
.080
.080
.080
.125
.125
.125
.125
.125
.125
.125
.140
.140
.140
.140
.140
.140
48
48
48
48
30
30
30
34
34
34
34
34
34
063-57693-000
063-57694-000
063-57695-000
063-57696-000
063-57718-000
063-57771-000
063-57775-000
063-57803-000
063-57807-000
063-58735-000
063-58736-000
063-60485-000
063-60488-000
007-06702-014
007-06702-014
007-06702-015
007-06702-015
007-06702-042
007-06702-005
007-06702-005
007-06702-018
007-06702-018
007-06702-009
007-06702-009
007-03257-130
007-03257-125
.064
.064
.064
.064
.080
.059
.059
.064
.064
.059
.059
.080
.080
.125
.125
.125
.125
.145
.112
.112
.125
.125
.112
.112
.145
.145
60
60
55
55
36
55
55
44
44
43
43
43
65

Gas Heating Controls

Transcription

Similar documents

save time and money

Gear Up for Springtime!

Service Parts List

2015 Spring Preseason Sale

Sect. 2 - Heating Elements

MERCHANDISING CATALOG 2012

Die BUCHSTAVIER - Das Dosierte Leben