Barco Line Doubler Kit for RCVDS 05 Installation

Transcription

Line Doubler Kit for RCVDS 05
R9828280
RCVDS05 + Quad Decoder+Line Doubler
Description:
This document provides information on the mounting of the Quad Decoder, the Decoder Interface module and the
Line Doubler module in the RCVDS 05 and its action on the specified input signals.
For other operational information, consult the Owner's Manual for the RCVDS 05 (order number R5975765).
Note: If interference disturbs the projected image in the (S)-Video mode, replace the input module S-Video R762244
(discrete version) by the S-Video input module R7622445 (SMD version).
Art. No.: R5975906 Rev. 06
1
Installation Instructions
Date: 06/10/2000 R9828280
R9828280
ATTENTION
To use the Quad Decoder feature in the RCVDS05, an adapted
communication software is required (see page 3)
KIT R762709
KIT R762710
Line Doubler
R7625625
Quad Decoder
R7627455
Decoder interface
R762705
10-wire Cable
Z3484106
9-wire Cable
Z348509
11-wire Cable
Z3495112
Screw R360862
Spacer
R367614
Spacer
R367614
Parts Listing for the Kit R9828280
Parts Listing for the Kit R762709
ITEM NO.
DESCRIPTION
ITEM NO.
DESCRIPTION
R32861910
U_S RCVDS05
R593010
R593472
R593545
R593546
R5975896
R5975906
BAG PE 80X 120X0.06 WL
BOXBLKAST 82X 55X 20
BAG ASTSH 203X 305
BAG ASTSH 152X 254
MAN SER EP51 RCVDS05DCOMB
MAN SER EP51 RCVDS05L_DBL
1
1
2
1
1
1
R367614
R7625625
V3247535
Z348509
Z3495106
Z3495112
SPR L25 M 3 H 5 NBRNI
UN LDB PJ53 *701
SPR L 1.5 D 3.1D 4.5 BRNI
CD CT FTFT P 9 100
CD CT FTFT P10 120
CD CT FTFT P11 130
R762709
R762710
UN LDB EP51C RCVDS05
UN DEC EP51C RCVDS05 +INT
1
1
R804793
BOX509AST 300X300X 55 2NB
1
QUANTITY
310
1
QUANTITY
6
1
2
1
1
1
Parts listing for the Kit R762710
ITEM NO.
DESCRIPTION
R360862
R367614
R762705
R7627455
SCR Z$7985 M 3 X 8 STZY
SPR L25 M 3 H 5 NBRNI
UN INT EP51 RCVDS05 COMB
UN DEC PJ53 *808S COMB_F
QUANTITY
7
3
1
1
2
Mounting Instructions
Date: 06/10/2000 R9828280
R9828280
The projector communication software checks the presence of the Quad Decoder in
the RCVDS 05 when an input source Video, S-Video or Component Video is selected.
When the projector uses the adapted communication software (see table below), these
input signal types are converted to RGB/S output signals.
IR Remote
Control
Communication link
Input Sources
Video
Projector
LCD
RGB-S*
RGsB*
S-Video
RCVDS05
+
Quad Decoder
+
LiDo
Component Video
Projector
CRT
RGB-CS
(32kHz)
* Video, S-Video and Component Video with separate Sync are converted into RGB-S Analog Signals.
* Component Video with Sync on Y is converted into RGsB Analog Signals.
RGB-S/RGsB
Input module for LIDO
(R762807)
CRT Projector type
Software version**
LCD Projector type
Software version**
BARCOVISION 701
BARCODATA 701
not adapted
not adapted
BARCODATA 5000
BARCODATA 8000
not adapted
not adapted
BARCOGRAPHICS 801S
BARCODATA 801S
from V5.30 on
from V5.30 on
BARCOGRAPHICS 8100
BARCODATA 2100
adapted from release
BARCODATA 1101
BARCOVISION 1600
not adapted
not adapted
BARCODATA 3100
BARCODATA 3000
from (V1.07**) - V2.07
from V2.07
BARCOGRAPHICS 1208
BARCOGRAPHICS 1209
from V5.31 on
from V5.31 on
BARCODATA 5100
BARCODATA 8100
from (V1.07**) - V2.07
from (V1.07**) - V2.07
BARCODATA 1109
BARCOVISION 1609
BARCOGRAPHICS 808
BARCODATA 808
** Soft V1.07 is made for the earlier type Pixel Map Processor part#
R762471.
**Software version of the projector can be read on the 'Start Up' or 'Identification' on screen menu.
3
Software Overview
Date: 06/10/2000 R9828280
R9828280
Mechanical disassembly of the RCVDS 05 for internal mounting of the kit
1. Removing the top cover
screw
Remove the 8 screws (4 on the top and 2 on each side).
Lift top cover clear of unit.
2. Removing the front panel (for software adaptation)
Pull off the power button.
4
EPROM Replacement
Date: 06/10/2000 R9828280
R9828280
Remove the screws holding frontpanel to main frame, two on bottom (A) and one on each side (B)
B
A
Remove the 6 screws holding control panel module to frontplate
Replace the EPROM IC3 by the one provided in the kit, if the existing software version is lower than 2.10.
CHECK: if the TEXT button is
pressed for a few seconds,
the version of the installed
software is shown on the
front panel display.
EPROM IC3
Re-install control panel module and power button following the above steps in reverse succession.
5
EPROM Replacement
Date: 06/10/2000 R9828280
R9828280
Mechanical mounting of the Decoder Interface module
Place the Decoder Interface module on the provided spacers (fig.1) on the main frame. Take care to line up the
threaded holes of the spacers with the holes on the module (fig.2).
provided spacers
to be plugged in on
Decoder Interface module
Fig.1
Secure the position of the Decoder Interface module by insertion of 3 spacers (A), 2 spacers (B) and two screws
(C) as shown below (fig. 2).
B
B
C
A
C
Decoder Interface module
A
fig. 3
Fig.2
6
Date: 06/10/2000 R9828280
R9828280
Interconnection Decoder Interface module, Power Supply and Module frame
Interconnection Module
frame/Decoder Interface
Plug in the 3 provided wire
cables on the Decoder Interface
to be plugged in on
Decoder module
Interconnection Power
Supply/Decoder Interface
Fig.4
Mounting the Decoder module
Place the Decoder module on the 3 provided spacers (fig.4) on the Decoder Interface module. Take care to line
up the threaded holes of the spacers with the holes on the module (fig.5).
Secure the position of the Decoder module by insertion of 2 spacers (A) and one screw (C) as
shown below (fig. 5).
B
A
C
fig. 3
A
C
Fig.5
7
Date: 06/10/2000 R9828280
R9828280
Interconnection Decoder module and Decoder Interface module (Fig.4 & Fig.6)
Interconnection Decoder/
Decoder Interface
Fig.6
Mounting the Line Doubler module
Place the Line Doubler module on the 4 provided spacers (fig.6) in the base. Take care to line up the threaded
holes of the spacers with the holes on the module (fig.7).
Secure the position of the Line Doubler module by insertion of 4 screws.
Line Doubler
Fig.7
8
Date: 06/10/2000 R9828280
R9828280
Interconnection Line Doubler module and Decoder Interface module (Fig.8)
Fig.8
9
Date: 06/10/2000 R9828280
R9828280
Mechanical re-assembly of the top cover
Putting back the top cover
Place the top cover on the unit and secure
with 8 screws (4 on the top and 2 on each
side).
Attention: the front side of the top cover is
provided with a notch. Ensure that the
notch enclosed the front top bar when
mounting the top cover (see illustration
below)
screw
10
Date: 06/10/2000 R9828280
R9828280
Routed inputs through the Line Doubler
R (32kHz)
R
Video
Video/S-Video
Input
Module
Signal transfer
G (32kHz)
Video/S-Video
to
R, G, B, S (32 kHz)
B (32kHz)
Video
G
B
CS 32kHz)
S-Video
Output
Module
H/CS
S-Video
V
RGB Analog
Input Module
Standard Sync
R
R
G/Gs
G/Gs Video
B
B
H/CS
Signal transfer
H/CS
V
RGB Analog
Input Module
Tri-Level Sync
V
R
R
G/G3s
Video
G/G3s
B
B
H/C3S
Signal transfer
S-Video
Output
Module
H/C3S
V
V
R (32kHz)
R-Y
Component Video
Input Module
Input signal = 15kHz
with Sync on Y
S-Video
Output
Module
R
Y
B-Y
Signal transfer
G (32kHz)
Decoding the
Input signal to RGB
+
Line Doubling (32kHz)
B (32kHz)
Video
G
B
CS (32kHz)
Output
Module
S-Video
H/CS
V
Component Video
Input Module
Input signal >15kHz*
or
Input signal = 15kHz
with sep. sync
R
R-Y
R
G
Y
Signal transfer
B-Y
S/3S
Decoding the
Input signal to RGB
Sync Separate
Video
G/G3s
B
B
CS/3S
Output
Module
S-Video
H/C3S
V
* Tri-Level Signal
R (32kHz)
R
LiDo Input
Module
G/Gs
B
S
R
Signal transfer
RGBs/RGsB
to
RGB-S with
Line Doubling**
G (32kHz)
G
B (32kHz)
B
CS (32kHz)
Video
Output
Module
S-Video
H/C3S
V
** If Fh>15kHz: Signal transfer to RGB with Sync separate on the original frequency
11
Routed inputs through the Line Doubler
Date: 06/10/2000 R9828280
R9828280
Printed in Belgium
12
Date: 06/10/2000 R9828280

Barco Line Doubler Kit for RCVDS 05 Installation

Transcription

Similar documents