SP-65 Manual - DK-TEC

Assembly Instructions
Model # SP-65
Step 1: Assemble Axle Assembly
A) Slide shaft collars onto axle toward gear housing.
B) Slide hopper frame onto axle through bushings.
C) Assemble wheels to axle with long cotter key through drive wheel and the short
cotter key outside free wheel through axle. See figure 1 page 1-11.
D) Snug up axle collars to frame and tighten. Make sure axle spins freely.
Step 2: Assemble Hopper to Frame
A) Insert spinner shaft through hole in bottom of hopper.
B) Assemble hopper to frame with (4) bolts (NOTE: do not tighten).
Step 3: Assemble leg to hopper frame with (4) bolts (NOTE: do not tighten).
Step 4: Assemble Handle
A) Assemble (2) Halves together with one bolt as shown.
B) Assemble cable bracket to handle with (2) bolts through both halves and tighten.
Step 5: Assemble handle assembly to leg
A) Slide handle onto leg and fasten with (2) bolts.
Step 6: Spin tires and make sure spreader is running smoothly.
Step 7: Tighten all bolts.
Step 8: Connect cable to gate.
Step 9: Tighten cable under cable clamp.
9
6
© Trynex International 2011 (REV A) F50753
Spreader Views
Model # SP-65
OFF
0N
PA-103354
10
© Trynex International 2011 (REV A) F50753
11
Hopper Assembly Parts Breakdown
Model # SP-65
11
12
© Trynex International 2011 (REV A) F50753
Hopper Assembly Parts Breakdown
Model # SP-65
Key
Part No .
D 5967
D 5973
D 5969
D 5701
D 5981
T 15133
Description
Hopper Cover
Screen
1/4-20 x 1-3/8 HHCS
1/4” Flat Washer Zinc
Hopper
1/4-20 Serrated Hex Flange Nut
Qt y.
1
1
4
4
1
4
12
© Trynex International 2011 (REV A) F50753
13
Axle Assembly Parts Breakdown
Model # SP-65
13
14
© Trynex International 2011 (REV A) F50753
Axle Assembly Parts Breakdown
Model # SP-65
Key
Part No .
D 5974
D 5923
D 5972
D 5971
D 5947
D 5993
D 5930
D 5916
D 5941
D 5911
D 5913
D 5910
D 5926
D 5909
D 5939
D 5938
D 5902
D 6024
D 5919
D 5921
Description
Hopper Frame Leg
Axle Bushing
Axle
Wheel
3/16 x 1-1/2” SS Cotter Pin
Agitator Wire
Lock Ring
Spinner Shaft
Axle Spacer
Gear Cover
Gear Support
Pinion Gear
Shaft Insert
Drive Gear
Spring Pin Spinner
Spring Pin Pinion Gear
Plastic Spinner
Axle Collar
3/16 x 2” Cotter Pin
3/16 x 1-1/4” Roll Pin
Qt y.
2
4
1
2
1
1
3
1
1
2
1
1
1
1
1
1
1
2
1
1
14
© Trynex International 2011 (REV A) F50753
15
Handle Assembly Parts Breakdown
Model # SP-65
15
16
© Trynex International 2011 (REV A) F50753
Handle Assembly Parts Breakdown
Model # SP-65
Key
Part No.
D 5917
D 5975
D 5976
D 5985
D 5983
D 5964
D 6158
T 15133
D 5701
D 5982
D 5970
D 5977
D 5987
Description
Handle Grip
Right Hand Upper Handle
Left Hand Upper Handle
10/32 x 2-1/2 Round Head Phillips
Cable Control
1/4-20 x 1-1/4 HHCS Zinc
10/32 Locknut
1/4-20 Serrated Flange Nut
1/4” Flat Washer
Cable Bracket
10/32 x 1/2 Phillips Truss Head
Frame Stand
1/4-20 x 2-1/4 HHCS
Qty.
2
1
1
2
1
2
6
7
7
1
2
1
5
Key
Part No.
D 5345
D 5905
D 5935
D 5936
D 5927
D 5928
D 5948
D 5912
D 5968
Description
Gate Slide
Bolt | #10-32 X 1/2" Hex Head MS Stainless
Locking Knob
Adjustment Knob Spring
Gate Stop Block
#10 Flat Nut
10-32 Nylox Nut SS
Gate Track
10-32 x 3/8 Phillips Fillister Head MS
Qty.
1
4
1
1
1
1
6
1
1
16
© Trynex International 2011 (REV A) F50753
17
Troubleshooting
Model # SP-65
TOO MUCH
MATERIAL FLOW
GATE STUCK OPEN
LUBRICATE GATE SLIDES
DROP SPREADER:
ADJUST FRONT GATE
SLIDE
ADJUST GATE STOP
LUBRICATE LINKAGE
REMOVE AND CLEAN
IF BROKEN, REPLACE
CABLE STUCK
LUBRICATE
REPLACE
RECONNECT
ACTUATOR / LINKAGE
NOT ENOUGH MATERIAL
FLOW
POOR SPREAD PATTERN
HANDLE DOES NOT WORK
ADJUST/REPLACE
HARDWARE / HANDLE
PHYSICAL OBSTRUCTION
REMOVE
GATE STUCK CLOSED
(SEE ABOVE)
AGITATOR IN PLACE
NO:
REPLACE
EMPTY HOPPER
FILL WITH MATERIAL
SCREEN BLOCKED BY
CLUMPS OF MATERIAL
REMOVE / BREAK CLUMPS
MATERIAL IS WET
REPLACE MATERIAL WITH
DRY MATERIAL
BROKEN SPINNER
REPLACE BROKEN PART
PUSH SPREADER
WRONG ROTATION.
SHOULD BE
COUNTER-CLOCKWISE
INSTALL WEATHER COVER
DRIVE WHEEL SHOULD BE
ON LEFT WHEN PUSHING
NO: REVERSE
AXLE ASSEMBLY
17
© Trynex International 2011 (REV A) F50753
9