DIGITAL LASER MFP

Transcription

DIGITAL LASER MFP

DIGITAL LASER MFP
SCX-4720F Series
SCX-4720FN/XAA
Basic Model : SCX-4720F
SERVICE
Manual
DIGITAL LASER MFP
CONTENTS
[ Key Features]
- Network Standard
(Network Printing, Network Scanning)
- Direct USB Features
( Print from USB device, Scan to USB device)
- 20 ppm Print/Copy Speed (14 ppm MDSP)
- 1200 dpi Print Resolution
- PCL6
- 64 MB System Memory
- 50 ADF
- 250 sh Paper Input (additional 250x1 Tray)
- 50 sh MP Tray
- 150 sh Paper Output
- 33.6 Kbps Fax Modem
- 200 Speed Dial
Precautions
1
1. Precautions
In order to prevent accidents and to prevent damage to the equipment please read the precautions listed
below carefully before servicing the printer and follow them closely.
1.1 Safety Warning
(1) Only to be serviced by appropriately qualified service engineers.
High voltages and lasers inside this product are dangerous. This printer should only be serviced by a suitably
trained and qualified service engineer.
(2) Use only Samsung replacement parts
There are no user serviceable parts inside the printer. Do not make any unauthorized changes or
additions to the printer, these could cause the printer to malfunction and create electric shock or fire hazards.
(3) Laser Safety Statement
The Printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, chapter 1 Subchapter J for
Class 1(1) laser products, and elsewhere, it is certified as a Class I laser product
conforming to the requirements of IEC 825. Class I laser products are not considered to be hazardous. The
laser system and printer are designed so there is never any human access to laser radiation above a Class I
level during normal operation, user maintenance, or prescribed service condition.
Warning >> Never operate or service the printer with the protective cover removed from Laser/Scanner assembly. The
reflected beam, although invisible, can damage your eyes. When using this product, these basic safety
pre-cautions should always be followed to reduce risk of fire, electric shock, and injury to persons.
CAUTION - INVISIBLE LASER RADIATION
WHEN THIS COVER OPEN.
DO NOT OPEN THIS COVER.
VORSICHT - UNSICHTBARE LASERSTRAHLUNG,
WENN ABDECKUNG GE FFNET.
NICHT DEM STRAHL AUSSETZEN.
ATTENTION - RAYONNEMENT LASER INVISIBLE EN CAS
D OUVERTURE. EXPOSITION DANGEREUSE
AU FAISCEAU.
ATTENZIONE - RADIAZIONE LASER INVISIBILE IN CASO DI
APERTURA. EVITARE L ESPOSIZIONE AL
FASCIO.
PRECAUCION - RADIACION LASER IVISIBLE CUANDO SE ABRE.
EVITAR EXPONERSE AL RAYO.
ADVARSEL. - USYNLIG LASERSTR LNING VED BNING, N R
SIKKERHEDSBRYDERE ER UDE AF FUNKTION.
UNDG UDSAETTELSE FOR STR LNING.
ADVARSEL. - USYNLIG LASERSTR LNING N R DEKSEL
PNES. STIRR IKKE INN I STR LEN.
UNNG EKSPONERING FOR STR LEN.
VARNING - OSYNLIG LASERSTR LNING N R DENNA DEL
R PPNAD OCH SP RREN R URKOPPLAD.
BETRAKTA EJ STR LEN. STR LEN R FARLIG.
VARO! - AVATTAESSA JA SUOJALUKITUS OHITETTAESSA
OLET ALTTIINA N KYM TT M LLE LASERS TEILYLLE L KATSO S TEESEEN.
Service Manual
Samsung Electronics
1-1
Precautions
1.2 Caution for safety
1.2.1 Toxic material
This product contains toxic materials that could cause illness if ingested.
(1) If the LCD control panel is damaged it is possible for the liquid inside to leak. This liquid is toxic. Contact with the skin
should be avoided, wash any splashes from eyes or skin immediately and contact your doctor. If the liquid gets into
the mouth or is swallowed see a doctor immediately.
(2) Please keep toner cartridges away from children. The toner powder contained in the toner cartridge may be harmful
and if swallowed you should contact a doctor.
1.2.2 Electric Shock and Fire Safety Precautions
Failure to follow the following instructions could cause electric shock or potentially cause a fire.
(1) Use only the correct voltage, failure to do so could damage the printer and potentially cause a fire or electric
shock.
(2) Use only the power cable supplied with the printer. Use of an incorrectly specified cable could cause the cable
to overheat and potentially cause a fire.
(3) Do not overload the power socket, this could lead to overheating of the cables inside the wall and could lead to
a fire.
(4) Do not allow water or other liquids to spill into the printer, this can cause electric shock. Do not allow paper
clips, pins or other foreign objects to fall into the printer these could cause a short circuit leading to an electric
shock or fire hazard..
(5) Never touch the plugs on either end of the power cable with wet hands, this can cause electric shock. When
servicing the printer remove the power plug from the wall socket.
(6) Use caution when inserting or removing the power connector. The power connector must be inserted completely otherwise a poor contact could cause overheating possibly leading to a fire. When removing the power
connector grip it firmly and pull.
(7) Take care of the power cable. Do not allow it to become twisted, bent sharply round corners or otherwise
damaged. Do not place objects on top of the power cable. If the power cable is damaged it could overheat and
cause a fire or exposed cables could cause an electric shock. Replace a damaged power cable immediately,
do not reuse or repair the damaged cable. Some chemicals can attack the coating on the power cable,
weakening the cover or exposing cables causing fire and shock risks.
(8) Ensure that the power sockets and plugs are not cracked or broken in any way. Any such defects should be
repaired immediately. Take care not to cut or damage the power cable or plugs when moving the machine.
(9) Use caution during thunder or lightening storms. Samsung recommend that this machine be disconnected from
the power source when such weather conditions are expected. Do not touch the machine or the power cord if it
is still connected to the wall socket in these weather conditions.
(10) Avoid damp or dusty areas, install the printer in a clean well ventilated location. Do not position the machine
near a humidifier. Damp and dust build up inside the machine can lead to overheating and cause a fire.
(11) Do not position the printer in direct sunlight. This will cause the temperature inside the printer to rise possibly
leading to the printer failing to work properly and in extreme conditions could lead to a fire.
(12) Do not insert any metal objects into the machine through the ventilator fan or other part of the casing, it could
make contact with a high voltage conductor inside the machine and cause an electric shock.
1-2
Service Manual
Samsung Electronics
Precautions
1.2.3 Handling Precautions
The following instructions are for your own personal safety, to avoid injury and so as not to damage the printer
(1) Ensure the printer is installed on a level surface, capable of supporting its weight. Failure to do so could cause
the printer to tip or fall.
(2) The printer contains many rollers, gears and fans. Take great care to ensure that you do not catch your fingers,
hair or clothing in any of these rotating devices.
(3) Do not place any small metal objects, containers of water, chemicals or other liquids close to the printer which if
spilled could get into the machine and cause damage or a shock or fire hazard.
(4) Do not install the machine in areas with high dust or moisture levels, beside on open window or close to a
humidifier or heater. Damage could be caused to the printer in such areas.
(5) Do not place candles, burning cigarettes, etc. on the printer, these could cause a fire.
1.2.4 Assembly / Disassembly Precautions
Replace parts carefully, always use Samsung parts. Take care to note the exact location of parts and also
cable routing before dismantling any part of the machine. Ensure all parts and cables are replaced correctly.
Please carry out the following procedures before dismantling the printer or replacing any parts.
(1) Check the contents of the machine memory and make a note of any user settings. These will be erased if the
mainboard or network card is replaced.
(2) Ensure that power is disconnected before servicing or replacing any electrical parts.
(3) Disconnect printer interface cables and power cables.
(4) Only use approved spare parts. Ensure that part number, product name, any voltage, current or temperature
rating are correct.
(5) When removing or re-fitting any parts do not use excessive force, especially when fitting screws into plastic.
(6) Take care not to drop any small parts into the machine.
(7) Handling of the OPC Drum
- The OPC Drum can be irreparably damaged if it exposed to light.
Take care not to expose the OPC Drum either to direct sunlight or to fluorescent or incandescent room
lighting. Exposure for as little as 5 mins can damage the surface’s photoconductive properties and will result
in print quality degradation. Take extra care when servicing the printer. Remove the OPC Drum and store it in
a black bag or other lightproof container. Take care when working with the covers(especially the top cover)
open as light is admitted to the OPC area and can damage the OPC Drum.
- Take care not to scratch the green surface of OPC Drum Unit.
If the green surface of the Drum Cartridge is scratched or touched the print quality will be compromised.
Service Manual
Samsung Electronics
1-3
Precautions
1.2.5 Disregarding this warning may cause bodily injury
(1) Be careful with the high temperature part.
The fuser unit works at a high temperature. Use caution when working on the printer. Wait for the fuser to cool
down before disassembly.
(2) Do not put finger or hair into the rotating parts.
When operating a printer, do not put hand or hair into the rotating parts (Paper feeding entrance, motor, fan,
etc.). If do, you can get harm.
(3) When you move the printer.
This printer weighs 17kg including toner cartridge and cassette. Use safe lifting and handling techniques. Use
the lifting handles located on each side of the machine. Back injury could be caused if you do not lift carefully.
(4) Ensure the printer is installed safely.
The printer weighs 17Kg, ensure the printer is installed on a level surface, capable of supporting its weight.
Failure to do so could cause the printer to tip or fall possibly causing personal injury or damaging the printer.
(5) Do not install the printer on a sloping or unstable surface. After installation, double check that the printer is stable.
1-4
Service Manual
Samsung Electronics
Precautions
1.3 ESD Precautions
Certain semiconductor devices can be easily damaged by static electricity. Such components are commonly called
“Electrostatically Sensitive (ES) Devices”, or ESDs. Examples of typical ESDs are: integrated circuits, some field
effect transistors, and semiconductor “chip” components.
The techniques outlined below should be followed to help reduce the incidence of component damage caused by
static electricity.
Caution >>Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
1. Immediately before handling a semiconductor component or semiconductor-equipped assembly, drain off any
electrostatic charge on your body by touching a known earth ground. Alternatively, employ a commercially available wrist strap device, which should be removed for your personal safety reasons prior to applying power to the
unit under test.
2. After removing an electrical assembly equipped with ESDs, place the assembly on a conductive surface, such as
aluminum or copper foil, or conductive foam, to prevent electrostatic charge buildup in the vicinity of the assembly.
3. Use only a grounded tip soldering iron to solder or desolder ESDs.
4. Use only an “anti-static” solder removal device. Some solder removal devices not classified as “anti-static” can
generate electrical charges sufficient to damage ESDs.
5. Do not use Freon-propelled chemicals. When sprayed, these can generate electrical charges sufficient to damage ESDs.
6. Do not remove a replacement ESD from its protective packaging until immediately before installing it. Most
replacement ESDs are packaged with all leads shorted together by conductive foam, aluminum foil, or a comparable conductive material.
7. Immediately before removing the protective shorting material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed.
8. Maintain continuous electrical contact between the ESD and the assembly into which it will be installed, until completely plugged or soldered into the circuit.
9. Minimize bodily motions when handling unpackaged replacement ESDs. Normal motions, such as the brushing
together of clothing fabric and lifting one’s foot from a carpeted floor, can generate static electricity sufficient to
damage an ESD.
1.4 Super Capacitor or Lithium Battery Precautions
1. Exercise caution when replacing a super capacitor
or Lithium battery. There could be a danger of
explosion and subsequent operator injury and/or
equipment damage if incorrectly installed.
3. Super capacitor or Lithium batteries contain toxic
substances and should not be opened, crushed, or
burned for disposal.
2. Be sure to replace the battery with the same or
equivalent type recommended by the manufacturer.
4. Dispose of used batteries according to the
manufacture’s instructions.
Service Manual
Samsung Electronics
1-5
Reference Information
2
2. Reference Information
This chapter contains the tools list, list of abbreviations used in this manual, and a guide to the
location space required when installing the printer. A definition of test pages and Wireless
Network information definition is also included.
2.1 Tool for Troubleshooting
The following tools are recommended safe and easy troubleshooting as described in this service manual.
• DVM (Digital Volt Meter)
Standard : Indicates more than 3 digits.
• Driver
Standard : "-" type, "+" type (M3 long, M3 short, M2
long, M2 short).
• Cleaning Equipments
Standard : An IPA (Isopropyl Alcohol) dry wipe tissue or
a gentle neutral detergent and lint-free cloth.
• Vacuum Cleaner
• Spring Hook
Standard : For general use
• Tweezers
Standard : For general home use, small type.
• Cotton Swab
Standard : For general home use, for medical service.
• Software (Driver) installation CD ROM
Service Manual
Samsung Electronics
2-1
2.2 Acronyms and Abbreviations
The table in the below explains abbreviations used in this service manual.
The contents of this service manual are declared with abbreviations in many parts. Please refer to the
table.
AC
Alternating Current
IC
integrated circuit
ADF
Automatic Document Feeder
IDE
ASIC
Application Specific Integrated Circuit
Intelligent Drive electronics or Imbedded
Drive Electronics
ASSY
assembly
IEEE
Institute of Electrical and Electronics
Engineers. Inc
BIOS
Basic Input Output System
IPA
Isopropy Alcohol
CCD
Charge Coupled Device
IPM
Images Per Minute
CMOS
Complementary Metal Oxide Semiconductor
LAN
local area network
CN
connector
lb
pound(s)
CON
connector
LBP
Laser Beam Printer
CPU
Central Processing Unit
LCD
Liquid Crystal Display
CRUM
Customer Replaceable Unit Memory
LED
Light Emitting Diode
dB
decibel
LSU
Laser Scanning Unit
dbA
decibelampere
MB
Megabyte
dBM
decibel milliwatt
MFP
Multi-Functional Product
DC
direct current
MHz
Megahertz
DCU
Diagnostic Control Unit
NVRAM
Nonvolatile random access memory
DPI
Dot Per Inch
OPC
Organic Photo Conductor
DRAM
Dynamic Random Access Memory
PBA
Printed Board Assembly
DVM
Digital Voltmeter
PCL
ECP
Enhanced Capability Port
Printer Command Language , Printer Control
Language
PDL
Page Discription Language
PPM
Page Per Minute
PTL
Pre-Transfer Lamp
Q’ty
Quantity
RAM
Random Access Memory
ROM
Read Only Memory
SCF
Second Cassette Feeder
SMPS
Switching Mode Power Supply
SPGP
Samsung Printer Graphic Processor
SPL
Samsung Printer Language
Spool
Simultaneous Peripheral Operation Online
SW
Switch
Sync
Synchronous or synchronization
TBD
To Be Determined
USB
Universal Serial Bus
EEPROM Electronically Erasable Programmable Read
Only Memory
2-2
EMI
Electro Magnetic Interference
EP
electrophotographic
EPP
Enhanced Parallel Port
FCOT
First Copy Out Time
F/W
firmware
GDI
graphics device interface
GND
ground
HBP
Host Based Printing
HDD
Hard Disk Drive
HV
high voltage
HVPS
High Voltage Power Supply
I/F
interface
I/O
Input and Output
Service Manual
Samsung Electronics
2.3 The Sample Pattern for the Test
The sample pattern shown in below is the standard pattern used in the factory.
The life of the toner cartridge and the printing speed are measured using the pattern shown below.
(The image is 70% of the actual A4 size).
2.3.1 A4 ISO 19752 Standard Pattern
This test page is reproduced at 70% of the normal A4 size
Service Manual
Samsung Electronics
2-3
2.4 Wireless LAN
• This product uses a printing function with a wireless LAN, which is an option.
- The wireless LAN function uses a frequency instead of connecting LAN cable to connect data to
an access point for print.
- For a wireless LAN connection, an AP is needed, It is possible to use wireless LAN onnection with
wired LAN. Also, if AP is installed in an office or at home, the wireless LAN function can be simply
used.
• Types of desk top PC (or Lap top) that uses the wireless LAN.
Division
Basic type
Recommend type
CPU
Over PENTIUM 233M
PENTIUM 300MHz
MEMORY
Over 64MB
Over 128MB
VIDEO CARD
Over 800X600
Over 1024X768
OS
Over WINDOWS 98
Over WINDOWS ME
INTERFACE CARD
A product has a certificated mark of Wi-FiTM
• About the certificated mark of Wi-FiTM
- The Wi-FiTM is a registered trademark of WECA (Wireless Ethernet
Compatibility Alliance). Over 50 of a wireless LAN companies are member
of it. The most of main wireless networking companies are attending and
the main companies are Lucent technologies, Cisco, Intel/Symbol, 3Com,
Enterasys (Cabletron), Compaq, IBM, Nokia, Dell, Philips, Samsung electronic, Sony, Intersil, and so on. This mark certifies mutual compatibility
among product has Wi-FiTM (IEEE 802.1) and it is certified as a standard of
a wireless LAN market.
2-4
Service Manual
Samsung Electronics
Specifications
3
3. Specifications
Specfications are correct at the time of printing. Product specifications are subject to change without notice.
See below for product specifications.
3.1 General Specifications
Items
SCX-4720F
SCX-4720FN
Service Manual
Samsung Electronics
3-1
Specifications
3.2 Print Specification
Items
3-2
SCX-4720F
SCX-4720FN
Service Manual
Samsung Electronics
Specifications
3.3 Scan Specification
Items
SCX-4720F
SCX-4720FN
Service Manual
Samsung Electronics
3-3
Specifications
3.4 Copy Specification
Items
3-4
SCX-4720F
SCX-4720FN
Service Manual
Samsung Electronics
Specifications
3.5 Fax Specification
Items
SCX-4720F
SCX-4720FN
Service Manual
Samsung Electronics
3-5
Specifications
(Continued)
Items
SCX-4720F
SCX-4720FN
SCX-4720F
SCX-4720FN
3.6 Paper Handling
Items
3-6
Service Manual
Samsung Electronics
Specifications
3.7 Software
Items
SCX-4720F
SCX-4720FN
Items
SCX-4720F
SCX-4720FN
3.8 Options
Service Manual
Samsung Electronics
3-7
Specifications
3.9 Consumables
Items
3-8
SCX-4720F
SCX-4720FN
Service Manual
Samsung Electronics
Summary of Product
4
4. Summary of Product
This chapter describes the functions and operating principal of the main components.
4.1 Printer Components
4.1.1 Front View
Service Manual
Samsung Electronics
4-1
Summary of Product
4.1.2 Rear View
* This wireless network antenna is not supplied with the machine. It is an option that must be purchased and
installed separately. (Option Function)
** The network port is not fitted as standard on the machine. You can purchase an optional Network Card and
install it separately.
*** If your country has a different telephone connection system, this socket may be blocked.
4-2
Service Manual
Samsung Electronics
Summary of Product
4.1.3 Control Panel (SCX-4720FN)
Service Manual
Samsung Electronics
4-3
Summary of Product
4-4
Service Manual
Samsung Electronics
Summary of Product
4.2 System Layout
The SCX-4720F/4520 is roughly made up Main Control part, Operation Panel part, Scanner part, Line Interface
part and Power part. Each Part is separated Module which focus on common and standard design of different
kind products. main control part adopting Fax & LBP Printer exclusive Controller is composed of 2 CPU and
1 Board. Scanner part is composed of ADF and Platen and is connected with Main by Harness.
4.2.1 Feeding section
There is a universal cassette which automatically loads paper and the manual feed which supplies paper single
sheet at a time. The cassette has a friction pad which separates paper to ensure single sheet
feeding, and it has a sensor, which checks when the paper tray is empty.
- Feeding Method: Universal Cassette Type
- Feeding Standard: Center Loading
- Feeding Capacity: Cassette-250 sheets (75g/m2, 20lb paper standard)
Manual 1 sheet (Paper, OHP, Envelop, etc.)
- Paper detecting sensor: Photo sensor
- Paper size sensor: None
4.2.2 Transfer Ass’y
This consists of the PTL (pre-transfer lamp) and the Transfer Roller. The PTL shines a light onto the OPC drum.
This lowers the charge on the drum’s surface and improves transfer efficiency.
The transfer roller transfers toner from the OPC drum surface to the paper.
- Life expectancy: Over 60,000 sheets (at 15~30°C)
4.2.3 Driver Ass’y
- Gear driven power unit. The motor supplies power to the paper feed unit, the fuser unit, and the toner
cartridge.
4.2.4 Fixing Part(Fuser)
- The fuser consists of the Heat Lamp, Heat Roller, Pressure Roller, Thermistor, and Thermostat. It fixes toner to
the paper using pressure and heat to complete the printing job.
4.2.4.1 Temperature-Intercepting Device (Thermostat)
The thermostat is a temperature sensing device, which cuts off the power to the heat lamp to prevent
overheating fire when the heat lamp or heat roller overheats.
4.2.4.2 Temperature Detecting Sensor (Thermistor)
The Thermistor detects the surface temperature of the heat roller, this information is sent to the main processor
which uses this information to regulate the temperature of the heat roller.
4.2.4.3 Heat Roller
The surface of the Heat Roller is heated by the Heat Lamp. As the paper passes between the Heat and Pressure
rollers the toner is melted and fixed permanently to the paper. The surface of the roller is coated with Teflon. This
ensures that toner does not adhere to the roller surface.
Service Manual
Samsung Electronics
4-5
Summary of Product
4.2.4.4 Pressure roller
The Pressure Roller mounted under the heat roller, it is made of a silicon resin, and the surface of the roller is
coated with Teflon. This ensures that toner does not adhere to the roller surface.
4.2.4.5 Safety Features
• To prevent overheating
- 1st protection device: Hardware cuts off when overheated
- 2nd protection device: Software cuts off when overheated
- 3rd protection device: Thermostat cuts off mains power to the lamp.
• Safety device
- Fuser power is cut off when the front cover is opened
- LSU power is cut off when the front cover is opened
- The temperature of the fuser cover's surface is maintained at less than 80ºC to protect the user and a caution
label is attached where the customer can see it easily when the rear cover is opened.
4.2.5 Scanner
This image is read using a photosensitive sensor. It consists of a CCD module, Connection board, ADF board,
AFE (Analog Front End), Image Processor (Located in CPU), platen glass and ADF mechanism.
• CCD Module Specification
1.Resolution: 600dpi/A4
2.Maximum scan wide: 8.5”
3.Color filter: Red, Green, Blue
4.Output channel: 3 channels (R, G, B)
5.Effective pixel: 5,400 pixel *3
6.Voltage: 24V & 5V
7.Pre-heating time: Maximum 30 seconds (70% of light output reached)
8.The life span of a lamp: 30,000 hours (25oC)
• Image Processor Specification
1.Operating frequency: 66MHz
2.Image sensor interface: 200/300/600 dpi CIS or CCD
3.Line time: Copy, FAX, Binary (Lineart, Halftone) PC Scan: 1.5ms/Line Color PC Scan (Grey, 256 Color,
True Color): 4.5ms/Line
4.A/D conversion: 10bit conversion
4-6
Service Manual
Samsung Electronics
Summary of Product
4.2.6 LSU (Laser Scanner Unit)
This is the core of the laser printer. It converts the video data received from the computer into an electrostatic
latent image on the surface of the OPC drum. This is achieved by controlling the laser beam and exposing the
surface of the OPC drum to the laser light. A rotating polygon mirror reflects the laser light onto the OPC and each
side of the mirror is one scan line. The OPC drum turns as the paper feeds to scan the image down the page.
The /HSYNC signal is created when the laser beam from LSU reaches the end of the polygon mirror and this
signal is sent to the controller. The controller detects the /HSYNC signal to adjust the vertical line of the image on
paper. In other words after the /HSYNC signal is detected the image data is sent to the LSU to adjust the left margin
on the paper.
Service Manual
Samsung Electronics
4-7
Summary of Product
4.2.7 Toner Cartridge
The toner cartridge is an integral unit containing the OPC unit and toner unit. The OPC unit consists of the
OPC drum and charging roller, and the toner cartridge unit consists of the toner, supply roller, developing
roller, and blade (Doctor blade)
- Developing Method: Non magnetic 1 element contacting method
- Toner: Non magnetic 1 element shatter type toner
- The life span of toner: 3,000 sheets (ISO 19752)
- Toner remaining amount detecting sensor: Yes
- OPC Cleaning: Electrostatic process
- Management of waste toner: Collect the toner using a Cleaning Blade
- OPC Drum protecting Shutter: Yes
- Classifying device for toner cartridge: ID is classified by interruption of the frame channel
-430V
-950V
-580V
4-8
Service Manual
Samsung Electronics
Summary of Product
4.3 System Description
4.3.1 Overview
SCX-4720FN is roughly made up Main Control part, Operation Panel part, Scanner part, Line Interface part and
Power part. Each Part is separated Module which focus on common and standard design of different kind products. main control part adopting Fax & LBP Printer exclusive Controller is composed of 2 CPU and 1 Board.
Scanner part is composed of ADF and Platen and is connected with Main by Harness . Line Interface part is
designed to apply TBR21 standard(Domestic,Europe,etc..)
4.3.2 CPU Part
1) CPU : Use 32Bit RISC Processor, ARM946ES,which is exclusive controller to execute Printer FAX Function
and to execute operation block by flash memory within system program, and to control whole system.
- Main function block
- Completely Integrated System for Embedded Applications,
- 32 Bit Risc Architecture, Efficient and Powerful ARM9 Core.
- LSU Interface Module for Interfacing PVC or HPVC with LSU
- 2 Channel General Purpose DMA Controller for High Speed I/O
- Dual Memory Bus Architecture
- Operation Frequency : AHB Bus: 60MHz, Internal System Bus: 120MHz
- Operation Voltage : 3.3V
- POWER ON RESET TIME : Below 5.6ms
2) Flash Memory : Record System Program, and download System Program by PC INTERFACE.
- FAX for Journal List, and Memory for One Touch Dial, Speed Dial List.
- size : 4M Byte
- Access Time : 70 nsec
3) SDRAM : is used as Swath Buffer in Printing, Scan Buffer in Scanning, ECM Buffer in FAX receiving, and
System Working Memory Area
- size 64MB : 64Mbyte(Basic).
TBD MB : System Working Memory Area and Scan Buffer
TBD MB : FAX Memory Receive Area
TBD MB : Printing System Working Memory Area
- Max Frequency : 133MHz
- store Fax Receive Memory Data by using Battery
Service Manual
Samsung Electronics
4-9
Summary of Product
4.3.3 Fax Part
1) Modem Part
<BLOCK DIAGRAM>
DSP
SSD
System
Side
Transfrom
CX20493
LSD
Line Side
Ext Line
Capacito
Primary Parts
Implemented by based on Conexant DAA (Data Access Arrangement) Solution , and is roughly composed of two
kinds Chip Solution
- CX82500(SFM336) : Existing Modem Chip which adds SSD (System Side Device) for interfacing
between
- LSD and DIB of FM336Plus Core
- CX20493(LSD) : LIU (Line Interface Unit) Chip which is controlled by SSD and satisfies each PSTN
requirements by modulating internal Configuration with connecting Tel Line.
Parallel synchronous data
TTL and CMOS compatible DTE interface
ITU-T V.24 (EIA/TIA-232-E) (data/control)
Microprocessor bus (data/configuration/control)
2) there is A/D, D/A Converter in LSD, so Analog Signal from Tel Line is transited in Digital through A/D Converter
in DAA and transfer to SSD by DIB Capacitor Digital Signal from SSD is converted to Analog by D/A Converter
in DAA and transfer to Tel Line
DSP
SSD
System
Side
Transfrom
CX20493
LSD
Line Side
Ext Line
Capacito
Primary Parts
4-10
Service Manual
Samsung Electronics
Summary of Product
4.3.4 Scan Part
Scan Part
Pictorial signal input part : output signal of CCD passes through Bypass_Cap change to ADC at AFE_CIP4 , and
defined signal between AFE_CIP4 and CIP4 processes the Image signal. When AFE accept each pixel,
CDS(Correlated Double Sampling ) technique which samples arm-level twice is used on each pixel by using CIP4
signal.
1) Pictorial image processing part : read CCD Pixel data in terms of 600dpi Line and process LAT algorithm on
Text mode, Error Diffusion Algorithm on Mixed mode, and store Data at Scan Buffer on PC Scan mode without
algorithm.
on every mode Shading Correction and Gamma Correction are executed ahead, then processing is executed
later.
* Scan Image Control Specification
Minimum Scan Line Time : 0.72ms
Scan Resolution : Max. 600DPI
Scan Width : 216mm
main function
- Internal 12bit ADC
- White Shading Correction
- Gamma Correction
- CCD Interface
- 256 Gray Scale
2) CCD Operating Part : CCD Image sensor use +5V and Inverter uses +24V
- CCD Maximum Operating Frequency : 10MHz
- CCD Line time : 0.72ms
- White Data output Voltage : 0.7V 0.5V (Mono Copy, 0.72ms/line)
- Maximum Inverter Current : 600 mA Max.( +24V)
Service Manual
Samsung Electronics
4-11
Summary of Product
4.3.5 Printer Part
Printer is consisted of the Engine parts and F/W, and said engine parts is consisted of the mechanical parts comprising Frame, Feeding, Developing, Driving, Transferring, Fusing, Cabinet and H/W comprising the main control
board, power board, operation panel, PC Interface.
The main controller is consisted of Asic(SPGPm) parts, Memory parts, Engine
Interface parts and it functions as Bus Control, I/O Handling, drivers & PC Interface by CPU.
Memory Access supports 16bit Operation, and Program Memory 2MB and Working Memory as well.
The Engine Board and the Controller Board are in one united board, and it is consisted of CPU part and print part
in functional aspect. The CPU is functioned as the bus control, I/O handling, drivers, and PC interface. The main
board sends the Current Image, Video data to the LSU and manages the conduct of Electrophotography for printing. It is consisted of the circuits of the motor (paper feed, pass) driving, clutch driving, pre-transfer lamp driving,
current driving, and fan driving.
The signals from the paper feed jam sensor and paper empty sensor are directly inputted to the main board.
4.3.6 ASIC
ASIC
ARM946ES
32-bit RISC embedded processor core
16KB instruction cache and 16KB data cache
No Tightly Coupled Memory
Memory Protection Unit & CP15 control program
Dual bus architecture for bus traffic distribution
AMBA High performance Bus (AHB)
System Bus with SDRAM
Printer Video Controller for LBP engines
Graphic Execution Unit for banding support of Printer Languages
Printer Video Controller for LBP engines
PVC : Printer Video Controller without RET Algorithm
HPVC : Printer Video Controller with RET algorithm
(Line Memory & Lookup Table Memory : 512 x 8 , 4096 x 16)
Engine Controller
Motor Control Unit
Motor Speed Lookup Table Memory (128 x 16 x 2)
Pulse Width Modulation Unit
4 Channels are supported
ADC Interface Unit
3 ADC Channels are available
ADC Core (ADC8MUX8) maximum clock frequency : 3 MHz
USB 2.0 Interface
Package : 272 pins PBGA
Power : 1.8V(Core), 3.3V(IO) power operation
4-12
Service Manual
Samsung Electronics
Summary of Product
Speed : 166MHz core(ARM946ES) operation, 60MHz bus operation
Service Manual
Samsung Electronics
4-13
Summary of Product
4.3.7 Sensor input circuit
1) Paper Empty Sensor
The Paper Empty sensor (Photo Interrupter) on the SMPS/HVPS PBA (CON2-2) is monitored by the
CPU on signal (nP_EMPTY). When the cassette is empty the printer displays a message on the LCD
panel.
2) MP Sensing
Presence of paper in the MP tray is detected by operation of the MP Sensor (Photo Interrupter) on the
SMPS/HVPS PBA (CON2-14). The CPU monitors signal(MP_EMPTY) to recognize paper in the MP, and
paper is fed from MP if there is paper present.
3) Paper Feed Sensor, (Toner Cartridge Sensor)
When paper passes the actuator on the feed sensor (CON2-1), it is detected by the Photo interrupter. signal(nP_FEED) monitored by the CPU and this signal starts the process of creating the image after certain
delay time If the feed sensor is not detected within 1 sec. after paper is fed, a paper Jam0 occurs.
(Displayed on the LCD panel).
When a toner cartridge is inserted it also operates the Paper Feed sensor. A message is displayed on the
LCD if no cartridge is detected.
4) Paper Exit Sensor
This detects that paper exits cleanly from the Machine using an exit sensor (CON2-24) on the engine
board and actuator on the frame. The monitors signal (P_EXIT) and detects the on/off time of the exit
sensor and if jam status is detected then JAM2 is displayed the on the LCD panel.
5) Cover Open Senser
The Cover open sensor actuator is located on the front cover and the senor is in the main frame. When the
front cover is opened the +24V supplies to the DC fan, solenoid, main motor, polygon motor part of LSU,
HVPS that are cut off. The CPU monitors signal (COVER_OPEN) to recognize when the cover is opened.
6) DC FAN / SOLENOID Driving
It is driven by a transistor and controlled by signal (FAN (SMPS, CON2-23)) bit of the CPU.
When it is high the fan is activated by turning on the TR, and it is off when the sleep mode is selected.
There are two solenoids and these are driven by the Paper Pick-up and MP signals. The drive time is
300ms. The diode protects the driving TR from the Back-EMF pulse which is generated when the solenoid is de-energized.
7) Motor Driving
The motor driving circuit is activated when the Driver IC is enabled. An A3977 (Motor driver IC) is used in
this case. The resistance Rs value of sensing and the voltage value of the V reference can be changed
by the motor driving voltage value.
4-14
Service Manual
Samsung Electronics
Summary of Product
4.4 SMPS & HVPS
The SMPS and HVPS are on one integrated board.
The SMPS supplies the DC power to the system. It takes either 110V or 220V and outputs the +5V, +12V and
+24V supplies to the main and other PBAs.
The HVPS creates the high voltage of THV/MHV/Supply/Dev and supplies it to the toner cartridge. The CPU is
used to modify some of these voltage settings to provide the ideal voltages to create the image.
The HVPS part uses the 24V and outputs the high voltage for THV/MHV/BIAS and the outputted high voltage is
supplied to the toner, OPC cartridge and transfer roller.
Service Manual
Samsung Electronics
4-15
Summary of Product
4.4.1 HVPS(High Voltage Power Supply)
1) Transfer High Voltage (THV+)
- Function : It is this voltage that transfers toner from the OPC Drum to the paper.
- Output voltage : +1300V DC±20V
- Error : IF THV (+) is not present, low density printing occurs due to toner on the OPC Drum not being
transferred to the paper. It is possible that waste toner over-flow can occur if this condition
persists. Ghost images may appear which repeat at 76mm intervals.
2) Charge Voltage (MHV)
- Function : It is this voltage that charges the surface of the OPC to -900V ~ -1000V.
- Output voltage : -1550V DC ± 50V
- Error : IF MHV is not present toner then since the OPC drum surface has no charge toner is attracted to
the whole OPC surface. A black page is printed out when this happens.
3)Cleaning Voltage (THV-)
- Function : It removes toner contamination from the rear side of the paper by sending (-) polarity to the
transfer roller forcing toner to transfer back to the to OPC drum.
- Output Voltage : -1200V, +300V/-150V
- Error : Smudges and toner contamination on the reverse side of the printed page.
4) Developing Voltage (DEV)
- Function: It is this voltage that develops toner with on to the section of the OPC drum surface exposed
by the LSU
(Laser Scanning Unit).
* When printing the exposed voltage on the OPC is -180V, unexposed is -900~-1000V, and the exposing
voltage on the DEV is -430V. Therefore toner with (-) polarity is developed onto an exposed
section of the OPC.
- Output voltage: -430V DC ± 20V
- Error: a) If DEV is GND, print density gets extremely low.
b) When DEV is floating due to poor connection between the frame and cartridge contacts etc.,
print density gets extremely high.
5) Supply Voltage (SUP)
- Function: It is this voltage that supplies toner to the developing roller.
- Output voltage: : -580V DC ± 50V (Use ZENER, DEV Gear)
- Error: a) When SUP is GND print density gets extremely low.
b) If SUP is floating due to poor connection between the frame and cartridge contacts etc. density
gets extremely low such that it is hard to see toner with the eyes
6) OPC Ground ZENER Voltage
- Function: It is this voltage that prevents image contamination under low temperature and low humidity
environment conditions.
- When a set prints without an output voltage, -130V DC ± 15V is maintained on OPC ground. (-103V
ZENER diode is connected to OPC ground)
- Error type: a) When the ZENER diode is - 0V there is no serious image problem in general environment, but in low temperature and low humidity environments it is possible that contamination
can occur on the entire image
b) When the ZENER diode is disconnected a blank page is printed out. (It is the same when
a ZENER diode is disconnected from OPC ground.)
4-16
Service Manual
Samsung Electronics
Summary of Product
4.4.2 SMPS (Switching Mode Power Supply)
This is the power source for the whole system. It is an independent module so that it is possible to use it for
common use. It is mounted at the bottom of the set.
It consists of the SMPS section, which supplies the DC power to drive the system, and the AC heater control part,
which supplies the power to the fuser. The SMPS has four output channels (+5V, +24V and 24VS).
There are three kinds of power, 120V exclusive (America), 220V exclusive (Europe), and 220V for China (nations
with unstable power supply).
1) AC Input
> Input Rated Voltage : AC 220V ~ 240V AC 120V / AC 220V(EXP version)
> Input Voltage fluctuating range : AC 198V ~ 264V AC 90V ~ 135V / AC 198V ~ 264V
> Rated Frequency : 50/60 Hz
> Frequency Fluctuating range : 47 ~ 63 Hz
> Input Current : Under 5.0Arms / 2.5Arms (When the fuser lamp is off and input / output voltages are in range)
2) Rated Output Power
NO
ITEM
CH2
CH3
1
CHANNEL NAME
+5V
+24.0V
2
CONNECTOR PIN
CON 3
CON 3
5V PIN: 8
24V PIN: 11,12,13
GND PIN: 7
GND PIN: 9,10
+5V & 5%
+24V & 10%
(4.75 to 5.25V)
(21.6 to 26.4V)
3
Rated Output
4
Max. Output Current
0.14 A
2.0 A
5
Peak Loading Current
0.14 A
2.5 A
6
RIPPLE NOISE
Voltage
100mVp-p
Under 500mVp-p
7
Maximum Output Power
0.35W
48W
8
Peak Output Power
0.7W
60W
9
Protection for short circuit
and current overload
Remark
1ms
1ms
-
3) Power Consumption
NO
ITEM
CH2 (+5V)
CH3 (+24V)
Remark
1
Stand-By
0.07A
0.4 A
AVG:55 Wh
2
PRINTING
0.14A
2.0 A
AVG 350 Wh
3
Sleep-Mode
0.01A
0.4A
AVG : 20 Wh
4) Length of Power Cord : 1830 ± 50mm
5) Power Switch : Fitted
Service Manual
Samsung Electronics
4-17
Summary of Product
6) Feature
-
Summary of Product
Insulation resistance : over 50M Ω (at DC500V)
Insulating retest pressure : Must be no problem within 1min. (at 1500Vzc, 10mA)
Leakage current : under 3.5mA
Operating current : under 40A peak (at 25°c, Cold start) Under 60A peak (in other conditions)
Rise Time : Within 2Sec
Fall Time : Over 20ms
Surge : Ring Wave 6KV-500A (Normal, Common)
7) Environment Condition
-
Operating temperature range : 0°C ~ 40°C
Storage temperature range : -25°C ~ 85°C
Storage humidity range : 30% ~ 90% RH
Operating atmospheric pressure range : 1
8) EMI Requirement : CISPR ,FCC, CE, MIC, C-Tick,
9) Safety Requirement
- IEC950, C-UL, TUV,Semko,iK,CB, CCC, EPA,
4.4.3 Fuser AC Power Control
The Fuser (HEAT LAMP) is heated using AC power. The AC power is controlled by a Triac (THY1), a
semiconductor switch. 'On/Off control' is achieved when the gate of the Triac is turned on/off by a Photo
triac (PC1), this is an insulting part.
In the other words the AC control part is a passive circuit. It turns the heat lamp on/off by taking a signal
from the engine control section. When the 'HEATER ON' signal is activated by the engine the LED of PC1
(Photo Triac) flashes. The flashing light causes the Triac (PC1) to switch and a voltage is supplied to the
gate of Triac THY1. As a result AC current flows in the heat lamp, and heat is produced.
On the other hand, when the signal is off, PC1 is off, the voltage is cut off at the gate of Triac THY1, this
Triac is therefore off, and thus the heat lamp is turned off.
1) Triac (THY1) feature
- 12A, 600V SWITCHING
2) Phototriac Coupler (PC3)
- Turn On If Current : 15mA ~ 50mA(Design: 16mA)
- High Repetive Peak Off State Voltage : Min 600V
4-18
Service Manual
Samsung Electronics
Summary of Product
4.5 Engine F/W
4.5.1 Feeding
If feeding from the cassette the drive of the pickup roller is controlled by controlling the pick-up solenoid. The on/off
of the solenoid is controlled by controlling the general output port or the external output port. If feeding from the
manual feeder the set decides to feed the paper according to the operation of the manual sensor, and by driving
the main motor, insert the paper in front of the feed sensor. When paper moves the occurrence of a paper jam is
judged as below.
4.5.1.1 Jam 0 – Jam in Feed area
• After a page was picked up, paper did not enter the unit due to a paper misfeed.
• After a page was picked up, paper entered but it did not reach the feed sensor in certain time due to slip, etc.
• After a page was picked up, if the feed sensor is not on try to pick up again. After retrying if the feed
sensor is still not on after certain time, it is Jam 0.
- this indicates that the leading edge of the paper doesn't pass the feed sensor within a certain time.
• Even though the paper reaches the feed sensor, the feed sensor does not turn on.
- this indicates that the leading edge of the paper already passed the feed sensor or that the sensor is fauty.
4.5.1.2 Jam 1 – Jam inside the print engine
• After the leading edge of the paper passes the feed sensor, the trailing edge of the paper does not pass the feed
sensor within certain time. (During this time the feed sensor cannot be Off)
• After the leading edge of the paper passes the feed sensor, the paper does not reach the exit sensor within certain time. (The exit sensor cannot be On during this time)
- There is already paper between the feed sensor and the exit sensor.
4.5.1.3 Jam 2 – Jam in the Exit area
• After the trailing edge of the paper passes the feed sensor the trailing edge of the paper does not pass the exit
sensor within certain time.
4.5.2 Drive
The main motor drives the paper feed, developing unit and the Fuser It is driven by software which controls the
acceleration, constant speed and deceleration profiles. The Motor is managed with an A3977 driver IC and controlled by step and enable signals from the CPU.
4.5.3 Transfer
The charging voltage, developing voltage and the transfer voltage are controlled by PWM (Pulse Width
Modulation). Each output voltage is changeable according to the PWM duty cycle. The transfer voltage used when
the paper passes the transfer roller is decided by environment recognition. The resistance value of the transfer
roller changes due to the surrounding environment in the room or within the set, this change in resistance in turn
changes the value of the voltage due to loading. This voltage is fed back into the set through the A/D converter.
Based on this fed back value the PWM cycle is changed to maintain the required transfer voltage
Service Manual
Samsung Electronics
4-19
Summary of Product
4.5.4 Fusing
The temperature of the heat roller's surface is detected according to the resistance value of the thermistor.
The thermistor resistance is measured using the A/D converter and thus the CPU can determine the
temperature of the heat roller. The AC power is controlled by comparing the target temperature to the value
from the thermistor. If the value from the thermistor is out of the controlling range while controlling the fusing
process, the error stated in the table occurs. (For the domestic model, the Q-PID method has been applied.)
4.5.4.1 Error Type
Error
Open heat error
Description
When warming up, it has been lower than 68 °C over 25 sec
Lower heat error
• Standby:
It has been lower than 100°C over 25 sec
• Printing:
- 2 consecutive pages: it has been lower than 145°C over 5 sec
- 3 consecutive page: it has been 40°C lower than the fixed fusing temperature over 4 seconds.
Over heat error
It has been higher than 220°C over 3 seconds
4.5.5 LSU
The LSU consists of the LD (Laser Diode) and the polygon motor control. When the printing signal occurs,
the LD is turned on and the polygon motor is enabled. When the light sensor detects the beam, Hsync occurs.
When the polygon motor speed becomes a normal, LReady occurs. If these two conditions are satisfied, the
status bit of the LSU controller register becomes 1 ant the LSU is judged to be ready. If the two conditions
are not satisfied, the error shown in the table below occurs.
Error
Polygon motor error
Description
When the polygon motor’s speed doesn’t become a normal
Hsync error
The polygon motor’s speed is normal, but the Hsync signal is not created.
4-20
Service Manual
Samsung Electronics
Summary of Product
4.6 OPE PBA
The OPE board consists of various function keys and an LCD to display set status and operator messages.
A MICOM (HOLTEC HT48R50) drives the LEDs and LCD. Communication between the OPE and the CPU
on the main board is serial (related signals are /Reset, TXD, and RXD).
4.7 USB Host
The USB Host PBA provides power to the USB connector to enable a USB Memory drive to be used in conjunction with
the USB Direct printing and Scan to USB functions.
Service Manual
Samsung Electronics
4-21
Summary of Product
4.8 Fax Section
4.8.1 Modem
• Group3 Facsimile Modem (Entire FM336/314 Family)
• External Handset Support (not implemented on SCX4720F)
• Requires Discrete Line Interface Unit (LIU )
• V.34 Half-Duplex Mode
• V.90 PCM/V.34 Duplex Data Modes
/RTS
XTLI
/CTS
XTLO
TXD
OR
TDCUK
CLKIN
Oscillator
XTCLK
V24
Interface
Crystal
/RLSD
RXD
RIN
/RDCLK
TXA1
/DTR
TXA2
/DSR**
DH
/RI*
RINGD
telephone
line
TIP
Line
Interface
RING
/TALK
/RD
Host
Processor
FM336
Modem
/WR
EYEXY
/CS
EYESYNC
/D[x:0]
EY RCLK
Optional
Eye Pattern
Generator
RS[4:0]
IRQ
/RESET
TXRQ*
SPKR
RXRQ**
Speaker
Amplifier
+SV
+3.3V
AGND
Power Supply
DGND
4-22
Service Manual
Samsung Electronics
Summary of Product
4.8.2 LIU PBA
The LIU board is the Line interface unit. It consists of a Tel_line Interface circuit and Telephone circuit.
The Tel_Line circuit consists of a matching transfer to conform to the impedance of the receiving telephone line and a
circuit to isolate the fax machine from the PSTN, and a surge absorber to protect against lighting strike surges on the
incoming line.
The Telephone circuit is consists of ring detection circuit, speech circuit, external hook detection circuit, and recall circuit.
4
1
5
3
1
TRANS MATCHING T1
2
TRANS MATCHING T2
3
RELAY RE1
4
VARISTOR VAR1/VAR2
5
JACK MODULAR(TEL) MJ1
6
JACK MODULAR(EXT) MJ2
6
2
Service Manual
Samsung Electronics
4-23
Summary of Product
4.8.3 Tel-Line Connection Circuit
• The Tel-Line Connection Circuit connects the fax machine to the PSTN using Tip and Ring terminals.
• Use Modular Plug : RJ-11C
• Arr1, Arr2 and Arr3 are protection components to prevent damage due to overvoltage surges, e.g. lightening.
4.8.4 Transformer Circuit
• The Transformer circuit is a line impedance matching circuit which matches the internal impedance of the fax machine
to the external -48Volt DC impedance of the PSTN system.
• The Transformer circuit insolates the fax machine electrically from the PSTN.
4-24
Service Manual
Samsung Electronics
Summary of Product
4.8.5 On Hook State
• DC10V ~ DC100V, DC Resistance : 5MΩ and over
• DC150V ~ DC200V, DC Resistance : 30KΩ and over
• Ring Sensitivity
- Ring detection voltage : 40Vrms ~ 150Vrms
- Ring detection frequency : 15.3Hz ~ 68Hz
- Ring detection current : 20mA ~ 100mA
• Pseudo Ring Sound
- Ring frequency : 750Hz + 1020Hz
- Ring Interrupt period : Mark/Space controlled by CPU/Modem
4.8.6 Off Hook State
• DC Resistance
- DP Dial Mode (DC 30mA) : 50 ~ 220 Ω
- DTMF Dial Mode (DC 20mA) : 50 ~ 300 Ω
- DTMF Dialing (DC 20mA) : 50 ~ 540 Ω
• Matching (Input AC Impedance) : 600 Ω±30% for 300Hz ~ 3.4KHz
• Minimum Line Current detecting Off Hook : 20mA(Handset Hook Off)
15mA(external Handset Hook Off)
• Minimum Line Current for DP Dial transmission : 20mA ~ 120mA
Product Margin : 20mA and over
Service Manual
Samsung Electronics
4-25
Summary of Product
4.8.7 Signal
• Input Signal Level Range : - 0dBm ~ - 48dBm
• DP (Dial Pulse) Dial
- Make / Brake Ratio : 40 : 60
- Pulse Speed : 10 ± 0.8 pps, Minimum Pause : above 60 msec
• DTMF Signal
- Coding Format
- Transmission Level
4-26
Service Manual
Samsung Electronics
Precautions
5
5. Disassembly and Reassembly
5.1 General Precautions on Disassembly
When you disassemble and reassemble components, you must use extreme caution. The close
proximity of cables to moving parts makes proper
routing a must.
If components are removed, any cables disturbed
by the procedure must be restored as close as
possible to their original positions. Before removing any component from the machine, note the
cable routing that will be affected.
Releasing Plastic Latches
Many of the parts are held in place with plastic
latches. The latches break easily; release them
carefully.
To remove such parts, press the hook end of the
latch away from the part to which it is latched.
Whenever servicing the machine, you
must perform as follows:
1. Check to verify that documents are not stored
in memory.
2. Be sure to remove the toner cartridge before
you disassemble any parts.
3. Unplug the power cord.
4. Use a flat and clean surface.
5. Replace only with authorized components.
6. Do not excessive force on components made of
plastic, they may break.
7. Make sure all components are in their proper
position.
Service Manual
Samsung Electronics
5-1
Precautions
5.2 Rear Cover
1. Remove the four screws securing the Rear Cover.
3. Unclip the Face Up Cover from the Rear cover, as
shown below. Then lift the Face Up Cover out.
Face Up Cover
2. Remove the Rear Cover from the Frame Ass'y and
Scanner Ass'y.
Rear Cover
5-2
Service Manual
Samsung Electronics
Precautions
5.3 Side Cover (LH, RH)
1. Before you remove the Side Cover (LH, RH), you
should remove:
- Rear Cover (see page 5-2)
2. Take out the Cassette.
4. Open the front cover and remove 2 screws on the
front. Release 3 clips underneath and pull the LH side
cover to the left, taking care not to damage the clips,
to remove it from the Frame Assembly. Take care to
disconnect the loudspeaker harness if fitted.
Side Cover (LH)
Cassette
3. Open the front cover and remove 2 screws on the
front and 1 screw on the back. Release 3 clips underneath, ease the rear screw bracket over its locating
pin and pull the RH side cover to the right, taking care
not to damage the clips, to remove it from the Frame
Assembly.
Side Cover (RH)
Service Manual
Samsung Electronics
5-3
Precautions
5.4 Front Cover
1. Open the Front Cover.
3. Unclip the Front Cover from the Frame Ass'y. Then
remove the Front Cover, as shown below.
Front Cover
2. Remove the Toner Cartridge.
5-4
Service Manual
Samsung Electronics
Precautions
5.5 Scanner Ass'y
1. Before you remove the Scanner Ass'y, you should
remove:
- Side Cover (LH, RH) (see page 5-3)
4. Pull up the Scanner Ass'y, as shown below.
Scanner Ass'y
2. Remove the 2 screws securing the Scanner Ass'y, as
shown below.
5. SCX4520 only. Lift the Platen Cover upward to
remove it.
1
3. Remove the 5 connectors and the ground wire screw
from the main PBA as shown below.
3
2
Service Manual
Samsung Electronics
5-5
Precautions
6. SCX4720F. Free the Scanner Cable Harness from the
clips underneath the scanner and release it from the frame.
8. Release the 3 clips on the front of the OPE unit and
remove the OPE unit as shown below, taking care to
thread the cable harness through the frame
CBF-HARNESS-OPE
Clips
7. Lift the front part of the COVER-OPE FRONT to
release the hook connecting the cover with the scan
assembly.
<SCX-4520>
Clips
COVER-OPE FRONT
<SCX-4520>
<SCX-4720F>
COVER-OPE FRONT
<SCX-4720F>
5-6
Service Manual
Samsung Electronics
Precautions
9. Remove the 4 screws securing the Scan Upper.
12. Pull up the CCD Shaft and take out the Scanner
Module.
Scanner Module
CCD Shaft
10. Unclip the Scan Upper from the Scan Ass'y by
releasing 2 clips on each side then pull the Scan
Upper upward and remove it.
Scan Upper
13. Squeeze the spring to release the tension in the Belt
and lift from the pulleys as shown below.
Spring
Belt
11. Remove the CCD Cable, as shown below.
CCD Cable
Service Manual
Samsung Electronics
5-7
Precautions
14. Remove the Reduction Gear and Idle Gear, as
shown below.
Gear-Reduction
Gear-Timing
Caution. Reassembling Scanner Module
1. When re-fitting the scanner belt and belt spring
take care to relocate the tension spring as close to
the right hand side of the scanner module as is
possible, as shown on the right.
2. When refitting the Scan Upper cover take care to
ensure that the cover open switch is not trapped.
Caution
Assembling Scanner Module When
re-assembling the scanner module, belt
and belt spring take care to relocate the
tension spring as close to the right hand
side of the scanner module as is possible,
as shown on the right.
5-8
Service Manual
Samsung Electronics
Precautions
15. Remove the 3 screws and take out the Motor
Bracket.
17. Unlatch the Open Sensor and remove it, as shown
below.
Motor Bracket
Open Sensor
16. Unplug the connector from the Open Sensor Ass'y.
18. Remove the CCD lock
Lock
CCD Lock
Unlock
Service Manual
Samsung Electronics
5-9
Precautions
5.6 ADF Motor Ass'y
1. Before you remove the ADF Motor Ass'y, you should
remove:
- Scanner Ass’y (see page 5-5)
4. Release the Bush and rotate it until it reaches the slot,
as shown below. Then lift the Pick-Up Ass'y out.
Pick up Ass y
2. Unclip the harness from the platen cover. Remove the
2 screws securing the ADF Ass'y and remove it, taking
care to thread the harness through the frame.
Bushing
ADF Ass y
5. Remove the 2 screws securing the Upper Cover and
remove it, as shown below.
3. Remove the Open Cover, as shown below.
Upper Cover
Open Cover
Caution. When working on the ADF Motor Ass’y take
care not to contaminate any of the rubber
surfaces with grease.
5-10
Caution. Before removing the ADF Motor Ass’y take
great care to note the position of the ferrite
core and the motor harness routing. When
refitting the ADF Motor Ass’y ensure that the
harness and ferrite are properly located and
are clear of the motor fan and white bar clip.
Service Manual
Samsung Electronics
Precautions
6. Unplug the one connector and remove 5 screws
securing the ADF Motor Ass'y. Then take out the ADF
Motor Ass'y.
ADF Motor Ass y
ADF Lower Ass y
Note. It is not necessary to disassemble the ADF unit in
order to change the ADF separator pad. Simply
open the ADF cover and remove the Pickup Ass’y
(step 4 page 5.10). Then, using a pair of tweezers
or a small flat-bladed screwdriver, release the clips
on each side of the ADF Separator Pad Ass’y.
Service Manual
Samsung Electronics
5-11
Precautions
5.7 OPE Unit(SCX-4520)
1. Before you remove the OPE Unit, you should remove:
4. Remove the Key Pad from the OPE Cover.
2. Remove the 7 screws securing the OPE PBA from to
the OPE Cover.
OPE Cover
Key Pad
OPE PBA
3. Remove the Contact Rubber from the OPE Cover.
Contact Rubber
5-12
Service Manual
Samsung Electronics
Precautions
OPE Unit(SCX-4720F)
1. Before you remove the OPE Unit, you should remove:
4. Remove the Key Pad from the OPE Cover.
2. Remove the 10 screws securing the OPE PBA from to
the OPE Cover.
OPE Cover
Key Pad
OPE PBA
3. Remove the Contact Rubber from the OPE Cover.
Contact Rubber
Service Manual
Samsung Electronics
5-13
Precautions
5.8 Middle Cover & Exit Roller
1. Before you remove the Middle Cover and Exit Roller,
you should remove:
- Scanner Ass'y (see page 5-5)
4. Remove the Exit Gear and Bearing, as shown below.
2. Remove the 4 screws securing the Middle Cover and
remove it.
3. Remove 2 screws securing the Controller Shield Ass’y
to the Middle Cover. Unclip the Middle Cover from the
Frame Ass'y, as shown below. Take care to release
the Shield Ass’y locating pegs and lift the Top Cover out.
Middle Cover
5-14
Service Manual
Samsung Electronics
Precautions
5.9 Controller Shield Ass’y
1. Before you remove the Main PBA, you should
remove:
- Side Cover(LH, RH) (see page 5-3)
2. Remove all of the connectors and the 5 screws connecting the Controller Shield Assembly to the Middle
Cover and frame and remove the assembly.
4. Remove 3 screws to remove the bracket from the
main board.
Main Board
Controller Shield Ass y
Bracket
3. If fitted remove the 2 screws connecting the NIC card
to the Controller Shield Assembly and remove the card.
NIC Card
Service Manual
Samsung Electronics
5-15
Precautions
5.10 Engine Shield Ass’y & Exit Board
1. Before you remove the Engine Shield Ass'y, you
should remove:
- Scanner (see page 5-5)
3. Remove the 11 screws securing the Engine Shield
Ass'y and tilt to one side. Then unplug the all the
HVPS/SMPS harness before removing the ass’y.
2. Unplug the Exit, AC and Fan connectors. Unplug the
LIU connector if fitted.
Thermistor
Main Connector
AC Connector
Fan Connector
Engine shild Ass y
4. Remove the 2 screws to remove the exit board.
Exit Board
5-16
Service Manual
Samsung Electronics
Precautions
5.11 SMPS and LIU
1. Before you remove the SMPS, you should remove:
- Engine Shield Ass’y(see page 5-16)
4. Remove the 3 screws securing the SMPS. Then lift
the SMPS out, as shown below.
SMPS
2. Remove the 2 screws securing the Inlet Bracket and
remove it
Inlet Bracket
3. Remove the one screw securing the Engine Shield
ground wire
5. Remove the 3 screws securing the LIU. Then lift the
LIU out, as shown below.
Service Manual
Samsung Electronics
5-17
Precautions
5.12 Fuser Ass'y
1. Before you remove the Fuser Ass'y, you should
remove:
4. Remove the 2 screws securing the Halogen Lamp.
Then take out the Halogen Lamp from the Heat Roller
2. Unplug the two connectors from the Main PBA and
SMPS, as shown below. Then remove the 4 screws
securing the Fuser Ass'y and remove it.
Heat Roller
Fuser Ass y
Halogen Lamp
5. Remove 4 screws to remove the fuser cover as
below. Remove 2 screws to remove the guide input.
3. Remove the 2 bolts securing the Thermostat. Then lift
the Thermostat out taking care not to loose the 2 nuts.
Claw
Fuser Cover
Bolts
Thermostat
Nuts
guide Input
5-18
Service Manual
Samsung Electronics
Precautions
6. Unwrap the Thermistor Harness, as shown below.
7. Remove the one screw securing the Thermister and
remove it, as shown below.
Thermistor
Thermistor
5.13 Fan
1. Before you remove the Fan, you should remove:
- Side Cover (RH) (see page 5-3)
2. Unplug the connector from the SMPS and remove the
one screw. Then take out the Fan.
DC Fan
Service Manual
Samsung Electronics
5-19
Precautions
5.14 LSU
1. Before you remove the LSU, you should remove:
- Front Cover (see page 5-4)
- Middle Cover (see page 5-14)
3. Unplug the two connectors.
2. Remove the 4 screws securing the LSU and remove it.
5.15 CRUM Board
1. Before you remove the CRUM Board, you should
remove:
- LSU (see page 5-20)
5-20
2. Remove the 4 screws to separate the CRUM board
from the main frame as below, taking care not to loose
the springs.
CRUM Board
Service Manual
Samsung Electronics
Precautions
5.16 Drive Ass'y
1. Before you remove the Drive Ass'y, you should
remove:
- Side Cover (LH) (see page 5-3)
- Shield Controller Ass’y (see page 5-9)
3. Take out the Drive Ass'y, then unplug the connector
from the Motor PBA, as shown below.
Drive Ass y
2. Remove the 5 screws securing the Drive Ass'y.
Drive Ass y
Caution. The six screws have numbers stamped. into
the Drive Ass’y base plate. When refitting the
Drive Ass’y tighten the screws the order they
are numbered. Only screw s numbered 1 to 5
are fitted at this stage. Screw 6 is fitted when
the Shield Controller Ass’y is refitted
5.17 Cover Mid Front
1. Before you remove the Cover Mid Front, you should
remove:
2. Remove the 4 screws securing the Cover Mid Front
and release 2 clips in the center. This cover is fragile
take care when removing it.
clips
Cover Mid Front
Service Manual
Samsung Electronics
5-21
Precautions
5.18 Transfer Ass'y
1. Before you remove the Transfer Ass'y, you should
remove:
- LSU (see page 5-20)
- Cover Mid Front (see page 5-22)
4. Remove the transfer roller by pressing the hook
securing the roller to the right using a tool.
2. Remove the 3 screws securing the Transfer Earth and
remove it.
Hook
Transfer Earth
5. Unlatch the Bushing and remove it. Then lift the
Transfer Roller out, as shown below.
Transfer Roller
Bushing
3. Unplug the PTL Holder connector, then remove the
PTL Holder and PTL Lens, as shown below.
PTL Lens
PTL Holder
5-22
Service Manual
Samsung Electronics
Precautions
5.19 Feed Ass'y
1. Before you remove the Feed Ass'y, you should
remove:
- Controller Shield Ass’y (see page 5-15)
- Drive Ass’y (see page 5-20)
4. Remove the 3 screws securing the Feed Bracket and
remove it.
Feed Bracket
2. Remove the 4 screws securing the Guide Paper Front
and remove it.
5. Remove the Feed Gear2.
ELA UNIT-MP
3. Remove the screws on the right and left sides of the
guide paper to remove the guides and the spring as
shown below.
Feed Gear2
Screw
Spring
Guide Paper
Service Manual
Samsung Electronics
5-23
Precautions
6. Remove the Feed Gear1 Ass'y.
7. Pull up the Feed Roller and Feed Roller1.
Feed Roller
Feed Gear1 Ass y
Feed Roller1
5-24
Service Manual
Samsung Electronics
Precautions
5.20 Pick-Up Ass'y & Solenoid
1. Before you remove the Pick-Up Ass'y, you should
remove:
- Controller Shield Ass,y (see page 5-15)
- Engine Shield Ass,y (see page 5-16)
- Drive Ass'y (see page 5-20)
- Feed Ass’y (see page 5-23)
4. Remove the 2 screws securing the Manual Solenoid
and Pick-Up Solenoid. Then remove Manual Solenoid
and Pick-Up Solenoid.
Pick Up Solenoid
2. Remove the Pick-Up Gear Ass,y.
Manual Solenoid
Pick up Gear Ass y
5. To replace the pick up roller, move the stopper securing the sponge-roller to the right and then turn the
sponge-roller to remove it from the shaft.
Stopper
Sponge Roller
Shaft
3. Take out the Pick-Up Ass'y, as shown below.
When replacing either the MP pick up roller or main
cassette pick up roller only, it is possible to do this by
turning the set over after removing the cassette and
the processor. See page 5-26
Bush
1
2
Service Manual
Samsung Electronics
5-25
Precautions
6. It is a simple matter to replace the MP Pickup
Roller and the main cassette Pickup Roller
without dismantling the set.
In both cases first remove the main paper
cassette, toner cartridge and front cover.
a) In order to replace the main cassette Pickup
Roller
1) Turn the set upside down
2) Release the white catch and slide the locking
piece as far to the side as possible.
3) Slide the white collar as far to the side as
possible.
4) Slide the Pickup Roller as far as possible to
the side, until it is free from the white collar on
the other end.
5) Rotate the Pickup Roller around the drive
shaft until it can be removed.
5-26
b) In order to replace the MP Pickup Roller
1) Release the white catch and slide the locking
piece as far to the side as possible.
2) Slide the white collar as far to the side as
possible.
3) Slide the Pickup Roller as far as possible to
the side, until it is free from the white collar on
the other end.
4) Rotate the Pickup Roller around the drive
shaft until it can be removed.
Service Manual
Samsung Electronics
Alignment & Adjustments
6
6. Alignment and Adjustments
This chapter describes some of the main service procedures including:
Using the EDC mode; Clearing paper jam and test patterns.
Much of this chapter is also included in the user's guide.
6.1 Paper path
Scanner Part
ADF-Roller
Pickup-Roller
Doc-Paper(30Sheets)
ADF-Idle Roller
Sensor-R gi
Sensor-Regi
Sensor-Doc
Exit-Roller
Feed-Roller
Sensor-Scan
Sensor-Scan
White-Sheet
hite-Sheet
CCD-Module
Engine Part
3
4
L S U
Fuser
Toner Cartridge
CR
DR
PR
PTL
TR
5
2
SR
6
FR
8
K /R
7
OPC
P IC
1
Service Manual
Samsung Electronics
6-1
6.1.1 Copy & Scan Document Path
Scanner Part
3
2
1
2
3
4
5
6
7
8
1
4
5
6
7
8
White-Sheet
CCD-Module
Doc. Paper (50 Sheets)
Pickup Roller
ADF Roller
Sensor - Doc.
Sensor - Regi
Sensor - Scan
Feed Roller
Exit Roller
6.1.2 Printer Paper Path
1) After receiving a print command, the printer feeds paper from the main cassette or manual feeder as required.
2) The paper being fed passes the paper feed sensor. (Jam 0 occurs if the sensor is not operated within a certain time)
3) Having passed the paper feed sensor the paper moves to the paper exit sensor via printing process. (Jam 1
occurs if the sensor is not operated within a certain time)
4) The paper then passes through the paper exit sensor and out of the set. (Jam 2 occurs if the trailing edge of the
paper does not pass the exit sensor within a certain time of the paper leading edge activating the exit sensor)
Engine Part
3
L S U
Fuser
Toner Cartridge
CR
DR
7
OPC
PR
5
6
FR
4
K /R
TR
2
SR
PTL
P IC
1
1
2
3
4
6-2
Paper Input (Cassette)
Paper Input (Manual Feeder)
Paper Out (Face Down)
5
6
7
Paper Empty Sensor (Cassette)
Paper Feeding Sensor
Paper Exit Sensor
Paper Empty Sensor (Manual)
Service Manual
Samsung Electronics
6.2 Clearing Paper Jams
Occasionally, paper can be jammed during a print job. Some of the causes include:
• The tray is loaded improperly or overfilled.
• The tray has been pulled out during a print job.
• The front cover has been opened during a print job.
• Paper was used that does not meet paper specifications.
• Paper that is outside of the supported size range was used.
If a paper jam occurs an error message appears in the LCD display. Find and remove the jammed paper.
If you don't see the paper, open the covers.
Do not use a tweezers, pincers or other metal tools when clearing a paper jam.
This could damage the internal mechanism causing print quality problems or possibly electrical shock.
L S U
ADF-Roller
Pickup-Roller
Doc-Paper(30Sheets)
Fuser
Toner Cartridge
CR
DR
EXIT
Sensor
ADF-Idle Roller
OPC
PR
SR
PTL
TR
Sensor-Regi
MP Sensor
Feed
Sensor
FR
K /R
Sensor-Doc
Exit-Roller
Feed-Roller
P IC
Sensor-Scan
Sensor-Scan
Empty Sensor
White-Sheet
Document Jam
(in the ADF area)
Paper Jam0
(in the paper feed area)
L S U
L S U
Fuser
Toner Cartridge
CR
Fuser
DR
EXIT
Sensor
OPC
PR
Toner Cartridge
CR
SR
DR
PTL
TR
EXIT
Sensor
MP Sensor
Feed
Sensor
FR
PR
OPC
SR
PTL
MP Sensor
Feed
Sensor
FR
K /R
TR
P IC
K /R
Empty Sensor
P IC
Empty Sensor
Paper Jam1
(in the fuser area or around the toner cartridge)
Paper Jam2
(in the paper exit area)
L S U
Fuser
Toner Cartridge
CR
DR
EXIT
Sensor
OPC
PR
SR
PTL
MP Sensor
Feed
Sensor
FR
K /R
TR
P IC
Empty Sensor
MP Tray Jam
(in the manual feed area)
Service Manual
Samsung Electronics
6-3
6.2.1 Clearing Document Jams
If a document jams while it is feeding through the ADF (Automatic Document Feeder),“DOCUMENT JAM ”
appears on the display.
6.2.1.1 ADF Input Misfeed
1) Open the ADF top cover.
3) Close the ADF top cover. Then load the documents
back into the ADF.
NOTE : To prevent document jams, use the document
glass for the thick, thin or mixed documents.
2) Pull the document gently to the right and out of the ADF.
6-4
Service Manual
Samsung Electronics
6.2.1.2 ADF Exit Misfeed
1) Open the document cover and turn the release knob to remove the misfed documents from the exit area.
2) Close the document cover.Then load the documents back into the ADF.
6.2.1.3 ADF Roller Misfeed
1) Open the document cover.
2) Turn the release knob so that you can easily remove
the misfed document, and remove the document
from the ADF or the feed area by carefully pulling it
towards the right by using both hands.
3) Close the document cover. Then load the documents
back into the ADF.
Service Manual
Samsung Electronics
6-5
6.2.2 JAM0 (In the Paper Feed Area)
1) Open and close the front cover.The jammed paper
automatically exits the machine.
If the paper does not exit,continue to Step 2.
4) Insert the paper tray into the machine until it snaps
into place.
2 Pull the paper tray open.
5) Open and close the front cover to resume printing.
3) Remove the jammed paper by gently pulling it
straight out.
If there is any resistance and the paper does
not move when you pull or if you cannot see
the paper in this area, skip to the fuser area
around the toner cartridge.
6-6
Service Manual
Samsung Electronics
6.2.3 JAM1 (In the Fuser Area or Around the Toner Cartridge Area)
NOTE : The fuser area is hot. Be careful when removing paper from the machine.
1) Open the front cover and remove the toner cartridge.
3) Replace the toner cartridge and close the front cover.
Printing automatically resumes.
straight out.
Service Manual
Samsung Electronics
6-7
6.2.4 JAM 2 (In the Paper Exit Area)
1) Open and close the front cover. The jammed paper
automatically exits the machine.
If the paper does not exit, continue to Step 2.
straight out..
2) Gently pull the paper out of the front output tray.
5) Close the rear cover.
3) If there is any resistance when you pull the paper or
the paper is not seen in the front output tray, open
the rear cover.
6-8
6) Open and close the front cover to resume printing.
Service Manual
Samsung Electronics
6.2.5 MP-Tray Jam (In the Bypass Tray)
“MP Tray Jam” appears on the display when you try to print using the manual feeder and the machine does not
detect paper, due to no paper or improper paper loading.
The error message may also occur when the paper is not properly fed into the machine through the manual feeder.
In that case, pull the paper out of the machine.
Service Manual
Samsung Electronics
6-9
6.3 User Mode(SCX-4520)
The table below shows the map of User settings available in User Mode. These are fully described in the
User Guide and are not included here.
1.Paper Setting
Paper Tray
Paper Size
2.Copy Setup
Change Default
Timeout
System Data
9.Maintenance
8.Machine Setup
Clean Drum
Clear Memory
6-10
6.Reports
Language
Power Save
CCD Power Save
USB Mode
Service Manual
Samsung Electronics
6.3 User Mode(SCX-4720F)
The table below shows the map of User settings available in User Mode. These are fully described in the
User Guide and are not included here.
1.Paper Setting
Paper Tray
Paper Size
4.Fax Feature
Delay Fax
Priority Fax
Add / Cancel
7.Sound/Volume
Speaker
Ringer
Key Sound
Alarm sound
2.Copy Setup
Change Default
Timeout
5.Advanced Fax
3.Fax Setup
Receive Mode
Ring to Answer
Contrast
Redial Term
Redials
MSG Confirm.
Auto Report
Auto Reduction
Discard Size
6.Reports
Send Forward
RCV Forward
Toll Save
Junk Fax Setup
Secure Receive
Prefix Dial No
Stamp RCV Name
ECM Mode
Phone Book
Send Report
RCV Report
System Data
Scheduled Jobs
Tx Confirm.
Junk Fax List
8.Machine Setup
9.Maintenance
Machine ID
Date&Time
Clock Mode
Dial Mode
Language
Power Save
CCD Power Save
USB Mode
Clean Drum
Notify toner
Clear Memory
Service Manual
Samsung Electronics
6-11
6.4 Tech Mode
6.4.1 How to Enter Tech Mode
In service (tech) mode the technician can check the machine and perform various tests to help with failure
diagnosis.
When in Tech mode the machine still performs all normal operations.
While in Tech mode the machine still performs all normal operations.
To enter the Tech mode (SCX-4720F)
To enter the Tech mode press
in sequence and the LCD
briefly displays ‘TECH’, the machine has entered service (tech) mode.
To enter the Tech mode (SCX-4520)
To enter the Tech mode press
in sequence and the LCD
briefly displays ‘TECH’, the machine has entered service (tech) mode.
6.4.2 Setting-up System in Tech Mode
SCX-4720F
SCX-4520
6-12
Service Manual
Samsung Electronics
6.4.3 Data Setup
SEND LEVEL
You can set the level of the transmission signal. Typically, the Tx level should be under -12 dBm.
Caution : The Send Fax Level is set to the best condition during manufacture. Never change settings arbitrarily.
DIAL MODE
This function can choose the dialing method.
*Default : Dial (Dial/Pulse)
MODEM SPEED
You can set the maximum modem speed.
When the fax establishes communication with a remote set the value of the maximum modem speed is
checked for both transmitter and receiver. The lowest value is used. It is best set at 33.6Kbps, the default
setting.
ERROR RATE
When the error rate is about exceed the set value, the Baud rate automatically adjusts to 2400 bps.
This ensures that the error rate remains below the set value.
You can select the rate between 5% and 10%.
CLEAR ALL MEMORY
The function resets the system to factory default settings.
This function is used to reset the system to the initial value when the product is functioning abnormally.
All the values are returned to the default values, and all the information which was set by the user
will be erased.
< Method >
1.
2.
3.
4.
Select the [MEMORY CLEAR] in TECH MODE.
Push the ENTER button.
Select your country. (There are four country groups. Refer to the table below.)
Push the ENTER button then it will clear all memory.
NOTICE : Always perform a memory clear after replacing the main board, otherwise the system may
not operate properly.
Country Group
USA/Canada
USA/Canada
Mexico
Brazil
Country
UK
Russia
UK
Germany
France
Italy
Spain
Austria
Netherlands
Belgium
Portugal
Sweden
Norway
Denmark
Finland
Switzerland
Greece
Ireland
Turkey
Russia
India
Oman
Poland
Bangladesh
Kuwait
Moroco
Algeria
Pakistan
UAE
Bahrain
Srilanka
Saudi Arabia
Chile
Peru
Argentina
Hungary
Romania
Bulgaria
Czech
Southafrica
South Africa
Service Manual
Samsung Electronics
6-13
FLASH UPGRADE
There are 2 methods to update the Flash Rom, Local and Remote.
(1) Local Machine
• RCP (Remote Control Panel) mode
This method is for Parallel Port or USB Port. Connect the PC and activate the RCP (Remote Control Panel) to
upgrade the Firmware.
< Method >
How to Update Firmware using RCP
1. Connect PC and Printer with a Parallel Cable or a USB Cable.
2. Run the RCP utility and select Firmware Update.
3. Search for the Firmware file to be used to update the set using the Browse Icon.
4. Click the Update icon. The firmware file is transmitted to the Printer automatically and the printer is
initialized when the download completes.
5. Click the Refresh icon and check that the updated version numbers are displayed.
• DOS Command mode
This method is ONLY for Parallel Port. Connect the PC to the set using a Parallel Cable and enter the DOS
Command to upgrade the firmware.
< Method >
1. First of all you need the following files : down.bat, down_com.bin, fprt.exe, and Rom File: (file name for
upgrade). Ensure you save ALL of these files in the same folder.
2. At the DOS prompt enter the correct command (as shown below) and push the enter key.
Then the upgrade will automatically take place..
3. There are two commands use the correct one depending on the condition of the set..
* When the product is in the idle condition
down "rom file"
* When the product is in Ready condition
(TECH MODE --> DATA SETUP --> FLASH UPGRADE --> LOCAL)
fprt "rom file"
4. Do not turn off the power during the upgrade process.
(2) Remote FAX
It is possible to use a set that already has the latest firmware to upgrade a remote set remotely using the telephone system.
< Method >
1. On the set that has the latest firmware set it toi transmit the upgrade:(TECH MODE •DATA SETUP•••• FLASH UPGRADE•••• REMOTE)
2. Enter the telephone number of the set that needs to be upgraded.
(Several faxes can be upgrade at the same time. In this case, enter each fax number.)
3. When the enter button is pressed the set sends the firmware file by calling designated fax number.
(Around 10~15 minutes are needed to send the file.)
< Caution >
1. The Sending and Receiving fax machines MUST be the same model.
2. The sending fax must be set up in ECM mode and the Receiving fax memory must be 100%.
If not the function will not work.
6-14
Service Manual
Samsung Electronics
6.4.4 Machine Test
SWITCH TEST
Use this feature to test all keys on the operation control panel. The result is displayed on the LCD window each
time you press a key.
MODEM TEST
Use this feature to hear various transmission signals to the telephone line from the modem and to
check the modem, amplifier and speaker. If no transmission signal sound is heard, it means the
modem part of the main board, amplifier, speaker or speaker harness is faulty.
DRAM TEST
Use this feature to test the machine's DRAM. The result appears in the LCD display.
If all memory is working normally, the LCD shows << O K >>
ROM TEST
Use this feature to test the machine's ROM. The result and the software version appear in the LCD
display.
• FLASH VER : 1.00 V
• ENGINE VER :1.00V
PATTERN TEST
Using this pattern printout you can check that the printer mechanism is functioning properly.
This function is for factory manufacturing use only.
SHADING TEST
The function is used to set the optimum scan quality determined by the specific characteristics of
the CCD (Charge Coupled Device). If copy image quality is poor perform this function to check the
condition of the CCD unit.
< Method >
1. Select the [Shading Test] in TECH MODE
(Menu, #, 1934).
2. Push the ENTER button and an image will
be scanned.
3. After scanning the CCD SHADING PROFILE will be print out.
4. If the printed image is different to the sample
image shown the CCD is defective.
NOTICE : When you test the CCD, make
sure that the cover is closed.
Service Manual
Samsung Electronics
6-15
6.4.5 Report
PROTOCOL LIST
This list shows the sequence of the CCITT group 3 T.30 protocol during the most recent sending or receiving
operation. Use this list to check for send and receive errors. If
SYSTEM DATA
This list provides a list of the user system data settings and tech mode settings.
6-16
Service Manual
Samsung Electronics
6.5 Engine Test Mode
The Engine Test Mode supplies useful functions to check the condition of the print engine. It tests the condition of each
device and displays the result of the test on the LCD. It is divided into 5 functions (0~4), and these are shown below.
6.5.1 To enter the Engine Test Mode
To enter the Engine Test mode (SCX-4720F)
Press
in sequence, and the LCD briefly displays
‘Engine Test’, the machine has entered Engine Test Mode.
Press “0”, “1”, “2”, “3” or “4” to select the Test No. (see list below – left hand column)
To enter the Engine Test mode (SCX-4520)
Press
in sequence, and the LCD briefly displays
‘Engine Test’, the machine has entered Engine Test Mode.
Press “0”, “1”, “2”, “3” or “4” to select the Test No. (see list below – left hand column)
6.5.2 Diagnostic
NO.
0
1
2
3
4
Sub No.
1
2
3
4
5
1
2
3
1
Engine test
Motor Test
Pick Up Test
Fan Test
Manual Clt Test
PTL Test
LSU Motor Test
LSU Hsync Test
LD Test
Feed Sensor Test
2
Exit Sensor Test
3
Cover Sensor Test
4
Empty Sensor Test
5
Manual Sensor Text
1
2
3
4
1
2
3
4
5
6
Therm ADC 180
Therm ADC 140
Therm ADC 120
Therm ADC 100
MHV Test
Dev Bias Test
THV EN/NEG Test
THV ON (1300V)
THV ADC 1300V
THV ADC 600V~3500V
Remark
1 : On, 2 : Off – next test selected
1. Check : read the sensor
2. Next : Next Sensor test
1 : On, 2 : Off (maintain the fusing temp. 80˚C)
1 : On, 2 : Off (-1550V ± 50V)
1 : On, 2 : Off (-430V ± 20V)
1 : On, 2 : Off (-1200V +300V/-150V)
1 : On, 2 : Off (+1300V ± 20V)
1 : On, 2 : Off (ADC Value : 101 ± 5)
1 : On, 2 : Off (Compare each ADC Value)
Service Manual
Samsung Electronics
6-17
6.5.3 Detail Description (Engine Test Mode)
Function Name
01.Motor Test
02.Pick Up Test
03.Fan Test
04.Manual Clutch Test
05.PTL Test
11.LSU Motor
12.LSU Hsync Test
13.LD Test
21.Feed Sen Test
22.Exit Sen Test
23.Cover Sen Test
24.Empty Sen Test
25.Manual Sen Test
31.Them ADC 180
32.Them ADC 140
33.Them ADC 120
34.Them ADC 100
41.MHV Test
42.Dev Bias Test
43.THV EN/NEG Test
44.THV ON(1300V)
45.THV ADC 1300V
46.THV ADC 600V~3500
6-18
Description
The main motor starts when the execution key is pressed
and stops when the stop key is pressed.
Automatically stops, when the execution is chosen.
stops, when the execution is chosen.
The fan starts when the execution key is pressed and
stops when the stop key is pressed.
The tray2,3 clutch is on for 1sec and then it automatically
stops, when the execution is chosen.On this function,
the main motor runs before 2sec from the point of the clutch
on in order to check the clutch state.
PTL(Pre-Transfer Lamp) is lights when the execution key
chosen and it stops when the stop key is chosen.
The laser motor starts when the execution key is pressed
and stops when the stop key is pressed.
The LSU motor starts and "Laser Ready" is displayed if
the motor spins at the correct speed, otherwise "Laser Error"
is displayed.
"Diode On" is displayed, when the laser diode is on.
Otherwise "Diode Off" is displayed.
These functions allow the current state of the sensor to be
displayed.
This function allows the current state of the Cover sensor
to be displayed. Touch the sensor and confirm that the
message changes: "Cover Open" to " Cover Close"
These functions allow the current state of the sensor to be
displayed.
"Current value" is displayed on the upper line of the LCD,
and "Target value" on the bottom line.
Target value is limited from "191°C" to "80°C"
These Functions are provided to check whether the
control of the HVPS is functioning correctly.
Display
Main Motor On/Off
Tray 1,2 Solenoid On/Off
Fan On/Off
Tray 2,3 Clutch On/Off
PTL On/Off
Laser Motor On/Off
Laser Leady On/Off
Diode On/Off
"Sensor Off" or “ Sensor On ”
"Cover Open" or "Cover Close"
"Sensor Off" or “ Sensor On ”
Target temperature and
output temperature from
thermistor and ADC.
MHV On/Off
Dev Bias On/Off
THV EN/NEG On/Off
THV On/Off
ADC value displayed.
ADC value displayed.
Service Manual
Samsung Electronics
6.6 Identify Sale Date (SCX-4720F Only)
This function confirms the date that the consumer bought the product and used the product for the first time.
When the consumer first operates the machine, it will start the scan and page counters.
The time the machine was first used is also displayed.
These settings are remembered after memory delete (Clear All Memory).
< Method >
Press MENU, #, 1, 9, 3, # in sequence. The Firmware version is displayed on the LCD.
Press 1( in the number keypad) : The LCD display shows "Updated date"
Press 2( in the number keypad) : The LCD display shows "Product first use date"
Service Manual
Samsung Electronics
6-19
6.7 Consumables and Replacement Parts
The life cycle outlined below is a general guideline for maintenance purposes and is for reference only.
Environmental conditions (temperature, humidity, dust etc.) and actual use can cause these figures to vary.
6-20
COMPONENT
REPLACEMENT CYCLE
ADF Rubber
20,000 Pages
Pick-up Roller
150,000 Pages
Friction Pad
60,000 Pages
Transfer Roller
60,000 Pages
Fuser Unit
80,000 Pages
Toner Cartridge
3,000 Pages (A4 ISO 5% Pattern)
Service Manual
Samsung Electronics
6.8 Abnormal Image Printing and Defective Roller
If a mark or other printing defect occurs at regular intervals down the page it may be caused by a damaged or
contaminated roller. Measure the repetition interval and refer to the table below to identify the roller concerned.
L S U
Fuser
Toner Cartridge
CR
DR
OPC
PR
SR
PTL
MP Sensor
FR
K/
R
TR
P IC
1
2
3
4
5
6
7
OPC Drum
Charge Roller
Supply Roller
Transfer Roller
Heat Roller
Pressure Roller
Developing Roller
No
Roller
Abnormal image period
Kind of abnormal image
1
OPC Drum
75.5mm
White spot, Block spot
2
Charge Roller
37.7mm
Black spot
3
Supply Roller
44.9mm
Horizontal density band
4
Develop Roller
35.2mm
Horizontal density band
5
Transfer Roller
47.1mm
Black side contamination/transfer fault
6
Heat Roller
77.8mm
Black spot and fuser ghost
7
Pressure Roller
75.4mm
Black side contamination
Service Manual
Samsung Electronics
6-21
6.9 Error Messages
The front panel displays the printer's status or error messages. Refer to the list below for an explanation of these
messages and how to clear problems. The messages and their meanings are listed in alphabetical order, with numbered
messages following.
MP Tray Jam [Door Open]
Meaning: A paper jam has occurred in the manual feeder or the multi-function printer detects improper feeding from
the manual feeder.
Solution: Clear the paper jam. Load paper in the manual feeder correctly.
Cancel ? 1. Yes 2. No (Only SCX-4720F)
Meaning: While storing the document in memory the memory has become full.
Solution: To cancel the fax job, press the ‘1’ button to accept “Yes.” If you want to send the pages that were stored
press the ‘2’ button to accept “No.” This will send ONLY the pages stored. The remaining pages should be
sent later when more memory becomes available.
[COMM. Error] (Only SCX-4720F)
Meaning: The multi-function printer has a communication problem.
Solution: Ask the sender to try again.
Low Heat Error / Open Heat Error
Meaning: There is a problem in the fuser unit.
Solution: Check thermostat, thermister contact point & Heating Lamp.
[Over Heat]
Meaning: The printer has overheated.
Solution: Your unit will automatically return to the standby mode when it cools down to normal operating temperature.
If failure persists,check the ELA HOU-FUSER.
Delayed Function Full (Only SCX-4720F)
Meaning: The delayed fax job list or memory space is full.
Solution: Cancel any unnecessary delayed fax jobs.
Document Jam
Meaning: The loaded document has jammed in the Automatic Document Feeder (ADF).
Solution: Clear the document jam.
[Door Open]
Meaning: The front or rear cover is not securely latched.
Solution: Close the cover until it locks into place.
Enter Again
Meaning: You entered an unavailable item.
Solution: Enter the correct item again.
Function Impossible
Meaning: You have tried to use a combination of printer functions that can not be used at the same time.
Solution: Reduce the number of selected functions or use only one function at a time.
Group Not Available (Only SCX-4720F)
Meaning: You have tried to select a group location number where only a single location number can be used, such
as when adding locations for a broadcasting operation.
Solution: Use a speed dial number or dial the number manually using the number keypad.
6-22
Service Manual
Samsung Electronics
[LSU Error]
Meaning: A problem has occurred in the Laser Scanning Unit (LSU).
Solution: Use TECH mode to test LSU. Replace the LSU
Invalid Cartridge or No Cartridge
Meaning: You have used an unauthorized cartridge.
Solution: You must use a Samsung approved cartridge.
[Line Error] (Only SCX-4720F)
Meaning: Your machine cannot connect with the remote machine or has lost contact because of a problem with the
phone line.
Solution: Try again. If the problem persists, wait an hour or so for the line to clear and try again. Or, turn the ECM
on.
Memory Full (Only SCX-4720F)
Meaning: The memory is full.
Solution: Delete any unnecessary documents (delayed transmission, broadcast or polling jobs) or retransmit after
more memory becomes available. This can also be caused when a large complex document with many
pages is being sent, try splitting the job into more than one operation.
[No Answer] (Only SCX-4720F)
Meaning: The remote fax machine has not answered after several redial attempts.
Solution: Try again. Verify the number to make sure a fax can be received.
No. Not Assigned (Only SCX-4720F)
Meaning: YThe speed dial location you tried to use has no number assigned to it.
Solution: Dial the number manually using the number keypad or assign the number.
No. Not Available (Only SCX-4720F)
Meaning: You have tried to delete the number for a delayed fax job.
Solution: Verify the number to be deleted and try again.
Or Delete the number after the delayed fax job is completed or deleted.
[No Paper] Add Paper
Meaning: The paper in the paper tray has run out.
Solution: Load paper in the paper tray.
Operation Not Assigned (Only SCX-4720F)
Meaning: You are performing an Add / Cancel operation, but there are no jobs waiting.
Solution: Check the display to see if there are any scheduled jobs. The display should indicate if any scheduled jobs
are in Standby mode, for example, Delay Fax.
[Paper Jam 0] Open/Close Door
Meaning: Paper has jammed in the feeding area of the paper tray.
Solution: Clear the jam.
[Paper Jam 2] Check Inside
Meaning: Paper has jammed in the paper exit area.
Solution: Clear the jam.
[Power Failure]
Meaning: The power has been turned off and then on and the printer’s memory has not been saved.
Solution: The printer’s memory was not saved due to a power failure. The job will need to be started over.
Service Manual
Samsung Electronics
6-23
Registered
Meaning: The group dial location is already registered with another speed dial number.
Solution: Select another group dial location.
[Retry Redial?] (Only SCX-4720F)
Meaning: The multi-function printer is waiting for a specified time interval to redial a previously busy station.
Solution: You can press <Select>to immediately redial, or <Cancel>to cancel the redial operation.
[Toner Low]
Meaning: The toner is almost empty.
Solution: Take out the toner cartridge and gently shake it. By doing this, you can temporarily reestablish printing
operations.
Or Replace the toner cartridge with a new one for the best print quality.
Priority Fax Function Full (Only SCX-4720F)
Meaning: The priority fax job queue is full.
Solution: Cancel any unnecessary priority fax jobs.
[Incompatible] (Only SCX-4720F)
Meaning: The remote machine did not have the requested feature, such as a sending a color fax.
This message also occurs if the remote machine does not have enough memory space to complete the
operation you are attempting.
Solution: Reconfirm the remote machine’s features.
[Jam 1] or [No Cartridge]
Meaning: Paper has jammed in the paper exit area. Or, the toner cartridge is not installed.
Solution: Clear the jam. Or, install the toner cartridge.
[Line Busy] (Only SCX-4720F)
Meaning: The receiving party did not answer or the line is already engaged.
Solution: Try again after a few minutes.
Load Document
Meaning: You have attempted to set up a copy or fax operation with no document loaded into the ADF.
Solution: Load a document into the ADF and try again.
Scanner Locked
Meaning: The scanner module is locked
Solution: Unlock the scanner and press Stop/Clear.
[Stop Pressed]
Meaning: The Stop/Clear button has been pressed during a copy or fax operation.
Solution: Try again.
[Toner Empty] Replace Toner
Meaning: The toner cartridge has run out. The machine stops printing.
Solution: Replace the toner cartridge with a new one.
[Retry Redial?] (Only SCX-4720F)
Meaning: The machine is waiting for a specified time interval to redial a previously busy station.
Solution: You can press Enter to immediately redial, or Stop/Clear to cancel the redial operation.
6-24
Service Manual
Samsung Electronics
Troubleshooting
7
7. Troubleshooting
7.1 Paper Feed problems – Causes and Solutions
7.1.1
Wrong Print Position
• Description
Printing begins when the paper is in the wrong position.
Check and Cause
Solution
A defective feed sensor actuator can cause incorrect
timing.
Replace the defective actuator
7.1.2 JAM 0
1. Paper does not exit from the cassette.
2. Jam-0 occurs when the paper feeds into the printer.
• Description
Check and Cause
L S U
Fuser
Toner Cartridge
CR
DR
EXIT
Sensor
OPC
PR
1. Check the Solenoid by using Tech
Mode.
1. Replace the solenoid.
2. Check cassette/MP knock-up plate
and springs.
2. Repair / replace as required
3. Check paper separator pad
3 Clean with soft cloth dampened with
IPA (Isopropyl Alcohol) or water.
Replace if required.
4. Check the pick up roller for
contamination and correct assembly.
4. Clean with soft cloth dampened with
IPA (Isopropyl Alcohol) or water.
Replace if required
5. If continuous clusters occur, check all
rollers between pickup and registration
sensor.
5. Ensure all rollers are clean and free to
operate correctly.
6 If the paper feeds into the printer and
Jam 0 occurs, perform Tech Mode to
check feed sensor.
6. Check the SMPS PBA, Main PBA and
all connections. Replace any faulty
parts or the Main PBA and/or Sensor.
SR
PTL
MP Sensor
Feed
Sensor
FR
K /R
TR
Solution
P IC
Empty Sensor
Service Manual
Samsung Electronics
7-1
Troubleshooting
7.1.3 JAM 1
1. Recording paper is jammed in front of or inside the fuser.
2. Recording paper is stuck in the discharge roller and in the fuser just after passing through the
Actuator-Feed.
• Description
Check and Cause
Solution
L S U
Fuser
Toner Cartridge
CR
DR
EXIT
Sensor
OPC
PR
SR
PTL
1. Replace the SMPS.
2. If the recording paper is stuck in the
discharge roller and the fuser just
after passing through the ActuatorFeed, Feed Actuator may be defec
tive.
2. Reassemble the Actuator-Feed and
Spring-Actuator if the return is bad.
MP Sensor
Feed
Sensor
FR
K /R
TR
1. If the recording paper is jammed in
front of or inside the fuser.
P IC
Empty Sensor
7.1.4 JAM 2
1. Recording paper is jammed in front of or inside the fuser.
2. Recording paper is stuck in the discharge roller and in the fuser just after passing through the
Actuator-Feed.
• Description
L S U
Fuser
Toner Cartridge
CR
DR
EXIT
Sensor
OPC
PR
SR
PTL
MP Sensor
Feed
Sensor
FR
K /R
TR
P IC
Empty Sensor
7-2
Check and Cause
Solution
1. If the paper is completely fed out of
the printer, but Jam 2 occurs: The
Exit sensor may be defective.
• After the paper is completely
discharged the Exit sensor actuator
should return to its original position
to shut the photo-sensor. It may
stick open or return only slowly due
to contamination be paper debris or
foreign objects.
1. Check if the exit sensor actuator is
defective.
• Check if the actuator exit is deformed
(Check if the lever part is deformed).
• Check whether burrs occur in the
assembly part of the exit actuator
and if the actuator operates smoothly.
• Check if foreign objects or paper
debris are preventing the correct
operation of the actuator.
2. If the paper is rolled in the Fuser
Roller:
• This occurs when a Guide claw is
broken away, damaged or
deformed.
• It occurs when the Spring of a
Guide claw is broken or damaged.
• It occurs when the Heat-Roller or
Pressure-Roller is seriously
contaminated with toner.
2. If the paper is stuck in the fuser :
disassemble the fuser and remove the
jammed paper, and clean the surface
of the pressure roller with dry gauze.
Check all ribs, claws and springs.
Service Manual
Samsung Electronics
Troubleshooting
7.1.5 Multi-Feeding
• Description
Multiple sheets of paper are fed at once.
Check and Cause
Solution
1. Check that the paper size guides are set correctly
(cassette and MPF tray).
1. Adjust paper guides.
2. Solenoid malfunction (the solenoid does not work
properly).
2. Replace the solenoids or PBA as appropriate.
3. Friction Pad is contaminated.
3. Clean the friction pad rubber with a soft cloth
dampened with IPA (Isopropyl Alcohol) or water.
4. Paper has a rough surface texture.
4. Use paper with a smother surface finish.
7.1.6 Paper rolled in the fuser
• Description
Paper rolled around fuser rollers or ‘Concertina’ jam
Check and Cause
Solution
1. Contamination of the pressure roller or heat roller.
1. After disassembling the fuser, clean contamination
from between the heat roller and the thermistor and
also clean contamination from the pressure roller.
Clean the surface of the rollers with IPA or water
2. Damaged or deformed ribs, claws or springs.
2. Check for damage or deformation of the print claws
and the holder plate claws, and repair or replace as
appropriate.
Service Manual
Samsung Electronics
7-3
Troubleshooting
7.1.7 Paper rolled on the OPC Drum
• Description
Paper is rolled up in the OPC.
Check and Cause
Solution
1. Paper is too thin.
1. Use paper that conforms to the printer specification.
2. The face of paper is curled.
2. Ensure paper is stored properly to prevent curl.
Note. To remove paper rolled in the OPC.
• Remove the toner cartridge from the set, taking
care not to touch the green surface. Use the
gearwheel at the side to rotate the OPC drum and
pull the paper from the cassette.
• Clean fingerprints on the OPC gently with soft
tissue, taking care not to scratch the surface.
7.1.8 Defective ADF
• Description
ADF (Automatic document Feeder) does not operate correctly.
Check and Cause
Solution
1. Check if the ADF rubber or HOLDER rubber are
damaged or contaminated.
1. Replace the contaminated or damaged part.
2. Check if the ADF Ass'y document sensors (3 paper
sensors) are working correctly.
2. If you cannot confirm the damaged part with the
7-4
Service Manual
Samsung Electronics
Troubleshooting
7.2 Set Malfunction – Causes and Solutions
7.2.1 LCD Display Defect (
• Description
in LCD Display)
Strange characters are displayed in the LCD Window and OPE Panel buttons do not work.
Check and Cause
Solution
1. Clear the memory. (see page 6-18)
1. Try again after clearing the memory.
2. Check that the OPE HARNESS is connected to
the Connection Board correctly.
2. If re-connecting the harness does not correct
the fault replace the OPE Ass’y and the main
Board in sequence.
7.2.2 Defective OPE Keypad
• Description
Pressing keys does not cause the set to respond correctly
Check and Cause
Solution
1. Clear the memory. (See page 6-18).
1. Check that the keypad is assembled correctly and
the membrane is not damaged, replace the
membrane or whole keypad assembly if necessary.
2. Check that there is an audible key click when a key is
pressed.
2. If the fault remains replace the OPE Ass’y and the
Main board in sequence.
Service Manual
Samsung Electronics
7-5
Troubleshooting
7.2.3 Fuser gear melts due to overheating causing Paper Jam.
• Description
Constant Jam where paper is entering Fuser unit.
Fuser rollers do not turn
Check and Cause
1. Check the Heat Lamp, thermostat and thermistor
Solution
1. Use EDC Mode to test the fuser.
Replace Fuser unit
Replace SMPS or Main PBA as appropriate.
7.2.4 Paper Empty
• Description
Paper Empty is displayed in the LCD panel even when paper is loaded in the cassette.
Check and Cause
Solution
1. Deformed paper sensor actuator or faulty sensor.
1. Replace the defective actuator or sensor.
2. SMPS PBA or Main PBA is defective
2. Replace the SMPS PBA or MAIN PBA as
appropriate.
3. Faulty cables or connectors.
7.2.5 Paper Empty without indication
• Description
The paper empty message does not appear in the LCD when the paper cassette is empty.
Check and Cause
Solution
1. Deformed paper sensor actuator or faulty sensor.
1. Replace the defective actuator.
2. SMPS PBA or Main PBA is defective
.
2. Replace the SMPS PBA or MAIN PBA as
appropriate
7-6
Service Manual
Samsung Electronics
Troubleshooting
7.2.6 Cover Open
• Description
The Cover Open message appears on the LCD even when the print cover is closed.
Check and Cause
Solution
1. The ‘Open Cover’ microswitch may be stuck or faulty
1. Use TECH mode(“cover sensor test”) to check
cover switch operation. Check and replace switch if
necessary.
2. The tab on the front cover may be damaged or broken
2. Replace the front cover.
3. Check the connector and cables between Switch and
main PBA.
3. Replace the Main Control board or Cover Open
S/W as necessary.
7.2.7 No error message when the cover is open
• Description
The Cover Open message does not appears on the LCD even when the print cover is open.
Check and Cause
1. The ‘Open Cover’ microswitch may be stuck or faulty
2. Check the connector and cables between Switch and
main PBA.
Solution
1. Use TECH mode(“cover sensor test”) to check
cover switch operation. Check and replace switch if
necessary.
2. Replace the Main Control board or Cover Open
S/W as necessary.
Service Manual
Samsung Electronics
7-7
Troubleshooting
7.2.8 Defective motor operation
• Description
Main motor is faulty and paper does not feed into the printer, resulting in Jam 0'
Check and Cause
1. The main motor harness or Motor PCB may be faulty.
Solution
1. Check the motor harnesses and connectors, replace
if defective.. If the problem persists replace the main
PBA.
Note Check motor operation using EDC Mode.
7.2.9 No Power
• Description
When system power is turned on the LCD panel does not come on.
Check and Cause
Solution
1. Check if the power input and SMPS output are normal.
1. Replace the power supply cord or SMPS. Check
power fuse and SMPS fuses replace if necessary.
2. LCD panel does not come on but normal start up
sounds are heard.
2. Replace the OP panel.
3. After replacing SMPS display does not come on and no
start up sounds are heard.
3. Replace the main PBA panel.
7.2.10 Printed Vertical Lines become curved
• Description
When printing, vertical lines are not straight.
Check and Cause
1. Check stability of 24V supply to LSU.
7-8
Solution
1. 24V stable - Replace LSU.
24V unstable replace SMPS, if the problem persists
replace the main PBA.
Service Manual
Samsung Electronics
Troubleshooting
7.3 Paper Feed Problems – Causes and Solutions
7.3.1 Wrong Print Position
• Description
Printing begins when the paper is in the wrong position.
Check and Cause
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
A defective feed sensor actuator can cause
incorrect timing.
Solution
Replace the defective actuator
7.3.2 Vertical White Line
• Description
White vertical voids in the image.
Check and Cause
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Solution
1. 1. Contamination of the window or
internal lenses of LSU mirror.
1. Clean the LSU window with recommended
cleaner (IPA) Clean the window with a
clean cotton swab. If dirt is inside the LSU
– replace LSU.
2. Foreign object inside the toner cartridge
or low toner.
2. Replace the toner cartridge.
3. Foreign object, contamination or burr on
the edge of the toner cartridge window.
3. Clean the exposure window.
4. If the fuser is defective, voids occur
periodically at the top of a black image.
4. Open the front cover and check the ribs
that correspond to the position of the
voids. Remove if found.
5. Contamination of the OPC drum.
5. If the problems are not solved, replace
the toner cartridge.
6. Depression or deformation of the surface
of the transfer roller
6. Replace the transfer roller.
Service Manual
Samsung Electronics
7-9
Troubleshooting
7.3.3 Horizontal Black Bands
• Description
1. Dark or blurry horizontal stripes occur in the printing periodically.
(These may occur at regular intervals down the page.)
Check and Cause
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Solution
1. Bad contacts on the toner cartridge high
voltage terminals.
1. Clean all HV terminals on the cartridge and
on the set frame. Ensure all toner or paper
dust particles are removed.
2. The rollers in the toner cartridge may be
contaminated.
Charge roller = 37.7 mm
Supply roller = 44.9 mm
Develop roller = 35.2 mm
Transfer roller = 47.1 mm
2. Clean the right Gear that has relatively
small tooth gap on the OPC.
3. If the problem persists replace the toner
cartridge.
7.3.4 Black/White Spot
• Description
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
1. Dark or blurry black spots occur periodically in the printing.
2. White spots occur periodically in the printing.
Check and Cause
Solution
1. If dark or blurry black spots occur periodically, the rollers in the Developer may be
contaminated with foreign matte or paper
particles.
( Charge roller : 37.7 mm interval
OPC drum : 75.5 mm interval)
1. Print several OPC cleaning Mode Prints
and then run the Self-test 2 or 3 times.
2. If faded areas or voids occur in a black
image at intervals of 75.5 mm, or black
spots occur elsewhere, the OPC drum
surface is damaged.
2. 75.5 mm repetition: Examine the surface of
the OPC drum and carefully clean with a
soft, lint free cloth. If unsuccessful replace
the cartridge.
37.7mm repetition: Replace the toner cartridge
3. If a black image is partially broken, the
transfer voltage is abnormal or the
transfer roller's life has expired.
3. The transfer roller guarantees 60,000
sheets printing. If the roller's life is expired,
replace it.
Note. Cleaning the inside of the set to
remove excess toner particles or paper
dust will reduce the occurrence of this
problem..
7-10
Service Manual
Samsung Electronics
Troubleshooting
7.3.5 Light Image
• Description
The printed image is light, with no ghost.
Check and Cause
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Solution
1. Toner Save mode enabled
1. Ensure the Toner Save mode is off. Check
set and driver settings.
2. Develop roller is contaminated or the
toner cartridge is almost empty.
2. Replace the toner cartridge and try to print
out again.
3. Ambient temperature is below than 10°C.
3. Wait 30 minutes after printer is powered on
before you start printing.
4. Bad contact caused by dirty terminals on
the toner cartridge or set.
4. Clean the cartridge and set contacts.
Generally clean dirt from inside the set.
5. Abnormal output from the HVPS.
(Run EDC mode – see sections 6.5.1
and 6.5.3)
5. Replace the HVPS if the problems are not
solved by the above four instructions.
7.3.6 Dark Image or a Black
• Description
The printed image is dark.
Check and Cause
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Solution
1. No charge voltage in the engine board.
1. Check the state of the connector which
connects the engine board and HVPS.
2. Charge voltage fault due to bad contact
between toner cartridge and set contacts.
2. Clean the high voltage charge terminals.
Note if 1 and 2 do not resolve the problem
and the problem persists replace the
HVPS.
3. VD0 signal of the Main PBA is Low state.
3. Replace the LSU Unit or Main PBA.
Service Manual
Samsung Electronics
7-11
Troubleshooting
7.3.7 Uneven Density
• Description
Print density is uneven between left and right.
Check and Cause
Solution
1. The pressure force on the left and right
springs of the transfer roller is not even,
the springs are damaged, the transfer
roller is improperly installed, or the transfer roller bushing or holders are damaged.
1. Replace both the left and right bush and
spring assemblies.
2. The life of the Toner cartridge has
expired.
2. Replace the toner cartridge and try to print out
3. The toner level is not even on the toner
cartridge roller due to the damaged blade
or low toner.
3. Gently shake the toner cartridge and try
printing again. If the problem persists
replace the toner cartridge.
7.3.8 Background
• Description
Light dark background appears in whole area of the printing.
Check and Cause
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Solution
1. Printing large quantities of low coverage
(2%) pages or the printer has not been
used for a long time.
1. The toner cartridge is basically designed to
print 3,000 sheets with 5% image. If it
prints more than 3,600 sheets with 2%
coverage, a background can occur.
2. Is a recycled toner cartridge be
used?
2. The A/S is not guaranteed if using a recycled toner cartridge.
Note try shaking the toner cartridge gently
from side to side. If the problem persists
replace the toner cartridge.
7-12
3. Has the life span of the toner
cartridge ended?
3. Replace the toner cartridge when its life is
expired.
4. Is the movement(Up and Down) of
the transfer roller smooth?
4. Clean the transfer roller bushes.
5. Is the HVPS normal?
5. Clean the high voltage charge terminals.
If this does not resolve the problem replace
the HVPS.
Service Manual
Samsung Electronics
Troubleshooting
7.3.9 Ghost (1)
• Description
Check and Cause
75.5 mm
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Ghost occurs at 75.5 mm intervals of the OPC drum in the whole printing.
1. Bad contacts caused by contamination
from toner particles between high voltage
terminal in the main body and the electrode of the Toner cartridge.
Solution
1 and 2. Clean all HV contacts, If problem
persists replace the HVPS.
If problem still persists replace the Main PBA
2. Bad contacts caused by contamination
from toner particles between high voltage
terminal in the main body and the one in
the HVPS board.
3. The life of toner cartridge is expired.
4. Transfer roller life (60,000 sheets) has
expired.
5. Low ambient temperature (below 10°C).
6. Damaged cleaning blade in the toner
cartridge.
out.
4. Check the transfer roller lifetime and
replace it.
5. Wait about 30 minutes after power on
before using printer.
out again
7.3.10 Ghost (2)
• Description
Ghost occurs at 75 mm intervals of the OPC drum in the whole printing.
(When printing on card stock or transparencies using manual feeder)
75 mm
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Check and Cause
When printing on card stock, thicker than
normal paper or transparencies, such as
OHP, a higher transfer voltage is required.
Solution
Ensure that the correct paper type is selected
in the printer driver or application software.
Remember to set back to normal paper after
use.
Service Manual
Samsung Electronics
7-13
Troubleshooting
7.3.11 Ghost (3)
• Description
Digital
Digital Printer
Printer
Check and Cause
Fuser contamination.
75.4 or 77.8mm
Digital
Digital Printer
Printer
Digital
Digital Printer
Printer
Ghost occurs at 75.4 or 77.8 mm intervals.
Solution
1. Disassemble the fuser and remove any
contamination on the rollers. Clean any
contamination from between the
Thermistor and the Heat roller. (Caution:
Take care not to deform the rollers.)
7.3.12 Ghost (4)
• Description
Digital
Digital Printer
Printer
75.4 or 77.8mm
Digital
Digital Printer
Printer
Digital
Digital Printer
Printer
A White ghost occurs in a black image printing at 32 mm intervals.
Check and Cause
Solution
1. The life of the developer may be expired.
1. Problem in the toner cartridge, replace the
toner cartridge and try to print out again.
2. Abnormal output from the HVPS.
(Run EDC mode – see sections 6.5.1
and 6.5.3)
2. Check the HVPS supply voltage. Clean all
HV terminals on the cartridge and on the
set. Replace the HVPS if the problem
persists.
7.3.13 Stains on the Face of the Page
• Description
The background on the face of the printed page is stained.
Check and Cause
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
7-14
Solution
1. Toner leakage due to improperly sealed
toner cartridge.
1. Replace the toner cartridge.
2. If the transfer roller is contaminated,
stains on the face of page will occur.
2. If the transfer roller is contaminated, run
PC Cleaning Mode Print 2 or 3 times and
then perform Self-Test 2 or 3 times to
remove contamination.
Service Manual
Samsung Electronics
Troubleshooting
7.3.14 Stains on Back of Page
• Description
The back of the page is stained at 47.1 or 75.4 mm intervals.
Digital
Digital Pri
Digital Printer
Digital Printer
Digital Printer
Check and Cause
Solution
1. 47.1mm : Transfer roller is contaminated.
1. Perform the OPC Cleaning Mode Print 2 or
3 times. Run Self-Test to remove the
contamination from the transfer roller.
Note. Replace the transfer roller if
contaminated severely.
2. 75.4mm : Pressure roller is contaminated.
2. Disassemble the fuser and clean the
H/R(Heat Roller) and P/R(Pressure roller).
Check and clean the area between the
H/R and the Thermistor. (Caution: Take
care not to deform the rollers.)
7.3.15 Blank Page Print out (1)
• Description
Blank page is printed.
Check and Cause
Bad ground contacts in OPC and/or toner
cartridge.
Solution
1. Check if the Ground-OPC or the OPC
Ground Zener diode are defective or open
circuit. (set inside left side).
2. Remove contamination of the terminals on
the toner cartridge and the unit.
7.3.16 Blank Page Print out (2)
• Description
1. Blank page is printed.
2. One or several blank pages are printed.
3. When the printer turns on, several blank pages print.
Check and Cause
1. Abnormal solenoid.
Solution
1. Perform the engine self test using TECH
Mode to check if the Solenoid is normal.
If the problem persists replace the main
PBA
Service Manual
Samsung Electronics
7-15
Troubleshooting
7.4 Fax & Phone Problems
7.4.1 No Dial Tone
• Description
There is no dial tone when the On-Hook dial button is pressed.
Check and Cause
Solution
1. Check that the telephone line cord supplied with
the set is connected to TEL LINE correctly.
1. If the telephone cord is OK but there is no dial tone, try
plugging a normal telephone into the wall socket. I this
is OK then replace the LIU B'd.
2. Listen for a CLICK sound when the OHD key is
pressed.
2. If you cannot hear the OHD CLICK sound, the OPE
Ass'y may be defective. Replace the OPE Ass'y.
3. Check the connection of the HARNESS between
the LIU and the Main B'd.
3. Check the Speaker connection and the harness
between the LIU and the Main PBA, replace as
necessary.
4. Check that the SPEAKER is connected correctly.
4. Use Tech mode / Modem Test to check that the
speaker and amplifier are working. Replace the Main B'd.
7.4.2 Defective MF DIAL
• Description
The MF DIAL is not functioning.
Check and Cause
Solution
1. Check that the telephone line cord supplied with
the set is connected to TEL LINE correctly.
1. If the telephone cord is OK but there is no dial tone, try
plugging a normal telephone into the wall socket. I this
is OK then replace the LIU B'd.
2. Listen for a CLICK sound when the keKEY is
pressed.
2. If you cannot hear the OHD CLICK sound, the OPE
Ass'y may be defective. Replace the OPE Ass'y.
3. Check the connection of the HARNESS between
the LIU and the Main B'd.
3. Check the Speaker connection and the harness
between the LIU and the Main PBA, replace as
necessary.
4. Check that the SPEAKER is connected correctly.
4. Use Tech mode / Modem Test to check that the
speaker and amplifier are working. Replace the LIU
and Main B'd in sequence
Notes: Product supports MF DIAL type only.
7-16
Service Manual
Samsung Electronics
Troubleshooting
7.4.3 Defective FAX FORWARD/RECEIVE
• Description
FAX FORWARD/RECEIVE is not functioning.
Check and Cause
Solution
1. Check that you can hear a dial tone by pressing
OHD.
1. If MODEM testing is normal and there is no dial tone,
then try replacing the LIU B'd.
2. Check that you can hear a RECEIVE tone when
MODEM testing in TECH Mode.
2. If testing the MODEM shows a fault replace the
Main B'd.
7.4.4 Defective FAX FORWARD
• Description
RECEIVE is functioning, but FORWARD is not functioning or received data is corrupt.
Check and Cause
Solution
1. Check if there is a NOISE line by pressing on-hook
dial and listening.
1. If you can hear a noisy line when using on-hook dial,
replace or repair the telephone line
2. Check that the destination fax machine can receive
forwarded faxes by using a different sending fax
machine (preferably from the same wall socket).
2. Replace LIU.
3. Check the cable between the set and the wall
socket for damage.
3. Replace the line cord.
Service Manual
Samsung Electronics
7-17
Troubleshooting
7.4.5 Defective FAX RECEIVE (1)
• Description
FORWARD is functioning, but RECEIVE is not functioning or the received data is corrupt.
Check and Cause
Solution
dial and listening
replace or repair the telephone line.
2. Use a different fax machine to receive from the
same sender (if possible on the same wall socket).
2. Replace the LIU.
• Description
Received data are lengthened or cut in the printing.
Check and Cause
Solution
dial and listening
replace or repair the telephone line
2. Ask sender to send to another fax machine
(if possible connected to the same wall socket)
2. Replace LIU or main PBA in sequence.
• Description
The phone is ringing continuously, but it set does not answer the call.
Check and Cause
Check that the RECEIVE Mode is set to FAX MODE.
7-18
Solution
If the fault persists even when the RECEIVE Mode is
changed to FAX MODE then replace the LIU and the
Main B'd in sequence.
Service Manual
Samsung Electronics
Troubleshooting
• Description
Received data is reduced by more than 50% in the printing.
Check and Cause
Check the FAX status of the forwarding side.
Solution
This is a problem with the sending fax machine.
Correct the setting on the remote machine..
7.4.9 Defective Automatic Receiving
• Description
The automatic receiving function is not working.
Check and Cause
1. Check that the RECEIVE Mode is set to FAX
MODE.
Solution
1. If the RECEIVE Mode is set to the TEL MODE, reset it
to the FAX MODE.
2. Even after the RECEIVE Mode is changed to the FAX
Mode, the problem persists then try to replace the LIU
and the Main B'd in sequence.
Service Manual
Samsung Electronics
7-19
Troubleshooting
7.5 Copy Problems
7.5.1 White Copy
• Description
Blank page is printed out when copying.
Check and Cause
Solution
1. Check the Scanner Cover is properly closed.
1. Room light can pass through a thin original.
2. Check shading profile.
2. Redo shading profile in the tech mode.
3. Check white/black reference voltage on Main PBA.
3. Replace the Main PBA.
7.5.2 Black Copy
• Description
Black page is printed out when Copying.
Check and Cause
7-20
Solution
1. Check for CCD problem on the Main PBA.
1. Check the CCD harness is properly connected.
Service Manual
Samsung Electronics
Troubleshooting
7.5.3 Abnormal noise
• Description
There is noise from the ADF when copying.
Check and Cause
Solution
1. Check the Scanner Motor, gearbox and rollers.
1. Check for correct assembly of gears and motor.
Ensure no parts are fouling and there are no foreign
objects in the mechanism or scanner path. Replace
any worn parts
2. Check the Motor Driver on Driver PBA.
2. Replace the main PBA.
7.5.4 Defective Image Quality
• Description
The copied image is excessively light or dark
Check and Cause
Solution
2. Check the gap between original and scanner
glass.
2. A gap of more than 0.5 mm can cause a blurred
image. Ensure rollers and cover close correctly.
Replace as necessary.
3. Check printing quality.
3. See "Print" troubleshooting.
Service Manual
Samsung Electronics
7-21
Troubleshooting
7.6 Scanning Problems – Causes and Solutions
7.6.1 PC Scanning problems
• Description
Unable to scan using a PC.
Check and Cause
Solution
1. Check the Cable (USB or Parallel) is properly
connected and that the printer can print correctly.
1. Reconnect the PC and printer, replace any faulty
cables. If using a parallel cable, check that the parallel port is properly configured in the BIOS.
2. Check that the driver is installed properly.
2. If printing is OK check that the Scan driver is also
installed (Refer to User's Manual.)
3. Check that the copy function operates normally.
3. If the copy function works, replace the Main PBA.
If the copy function doesn't work, replace the CCD
Ass'y and try again.
7.6.2 Poor Quality of PC Scanned images
• Description
The image PC scanned is not clear or bad.
Check and Cause
Solution
1. Use TECH mode to carry out a shading test (see
page 6.15) and examine the waveform printout.
1. If the CCD waveform form is abnormal replace the
CCD Ass'y.
2. Check if the resolution is set too low in PC Scan
options. (Refer to User's Manual.)
2. Teach the user about scanner resolution – refer to
the User Guide.
7-22
Service Manual
Samsung Electronics
Troubleshooting
7.7 Toner Cartridge Service
Only toner cartridges supplied by Samsung should be used. Printing defects or set damage caused by the use of
non-approved toner cartridges or un-licensed toner refills are not covered by the guarantee.
7.7.1 Precautions on Safe-keeping of Toner Cartridge
Excessive exposure to direct light for more than a few minutes may cause damage to the cartridge.
7.7.2 Service for the Life of Toner Cartridge
If the printed image is light due to the toner supply becoming low you can temporarily improve the print quality by
redistributing the toner (Shake the toner cartridge), however you should replace the toner cartridge to solve the problem
permanently.
7.7.2.1 Redistributing Toner
When the toner cartridge is near the end of its life, white streaks or light print occurs. The LCD displays the warning message, “Toner Low.” You can temporarily reestablish the print quality by redistributing the remaining toner in the cartridge.
1. Open the Front Cover.
3. Unpack the new toner cartridge and gently shake it horizontally four or five times to distribute the toner evenly
inside the cartridge.
4. Save the box and the cover for shipping. Slide the new
toner cartridge in until it locks into place.
2. Lightly pushing the used cartridge down, pull it out.
Note : Help the environment by recycling your used toner cartridge. Refer to the recycling brochure packed with the
toner cartridge for details.
Service Manual
Samsung Electronics
7-23
Troubleshooting
7.7.3 Standard of guarantee for consumable parts.
Please refer to User's Manual or Instructions on Fax/Printer Consumables SVC manual for the criteria for judging the
quality of consumable parts the standard of guarantee on those parts.
• Spotting a refilled cartridge by eye.
One way security screws are used in the manufacture of the cartridge – check if these are damaged.
7.7.4 Error messages in the LCD window related to toner.
This section explains messages on the LCD that are related to the data stored in the EEPROM in the toner cartridge.
7.7.4.1 Toner Low
- Explanation: The amount of toner remaining is less than 10%
- Solution: The cartridge is almost empty or life-expired – replace the cartridge.
7.7.4.2 Toner Empty
- Explanation: The toner cartridge is empty
- Solution: Replace the cartridge.
7.7.4.3 Drum Warning
- Explanation: This message appears when the OPC drum is nearing the end of its life (14,000pages). This means
that the life of the mechanical parts in the cartridge has expired (this is not an indication of toner remaining).
- Solution: After printing about 15,000 pages, in a worst case scenario, the waste toner collector might overflow and it
may cause the system to fail. Also after 15,000 pages the OPC drum surface will be becoming worn and print quality
will degrade, print images will become misty. It is therefore necessary to replace the cartridge even though there may
be toner left in it.
When this message occurs there are approximately 1,000 pages left.
7.7.4.4 Replace Drum
- Explanation: The toner cartridge mechanical life is expired.
- Solution: Replace the cartridge.
7-24
Service Manual
Samsung Electronics
Troubleshooting
7.7.5 Signs and Measures of Poor toner cartridge
Fault
Light image and
partially blank
image
(Cartridge life is
ended.)
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Signs
• The printed image
is light or dirty and
untidy.
• Parts of the image
are not printed.
• Periodically a "tick
tick" noise occurs.
Cause & Check
1. If the image is light or dirty
and untidy - Shake the toner
cartridge and then recheck.
OK: Lack of toner, so the life
is nearly expired.
2. Some part of image is not
printed - Shake the toner
cartridge and then recheck.
(1)NG: clean the LSU window
with a cotton swab, then
recheck.
(2)OK: Lack of toner, so the
life is nearly closed.
3. Periodically a noise like "tick
tick" occurs - Measure the
time between ticks.
4. White vertical stripes on the
whole or part of the page :
Shake the toner cartridge and
then recheck. OK: Lack of
toner, so the life is nearly
expired
Solution
1. All of 1, 2, 3
If image quality improves by
shaking, replace with a new
toner cartridge. Perhaps up to
100 pages left before out of
toner.
2. For item 2If image quality improves after
cleaning the LSU window then
the toner cartridge is normal.
(Contamination on the LSU
window has caused image
quality problems.)
3. For item 3If the time between ticks is
about 2 seconds, the toner
inside the toner cartridge is
almost exhausted.
( Purchase and replace with a
new toner cartridge. Perhaps up
to 200 pages left before out of
toner)
4. For item 3This is a phenomenon caused
by lack of toner, so replace the
toner cartridge.
Toner
Contamination
• Toner
contamination of
the printed page at
regular intervals
down the page.
• Random Toner
contamination over
the whole or large
parts of the paper
surface.
1. Contamination at regular
intervals.
(a)Check the distance
between contamination
marks.
(b)Check the appearance of
both ends of the toner
cartridge OPC drum.
1.(a) Refer to section 7.6
2. Random page contamination.
(a) Check that the terminals
(contact points) of the toner
cartridge and the set are
clean.
(b) Check that the terminals
(contact points) of the toner
cartridge and the set are not
damaged.
2. Clean all HV contacts. If the
problem persists replace the
cartridge.
1.(b) If both ends of the OPC drum
are contaminated with toner:
Check no. of pages printed using
this cartridge – perhaps waste
toner collector is full.
Service Manual
Samsung Electronics
7-25
Troubleshooting
Fault
White Black spot
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Signs
• Light or dark black
dots on the image
occur periodically.
• White spots occur
in the image
periodically.
Cause & Check
Solution
1. If light or dark black dots
occur at regular intervals this
is because the toner cartridge
rollers are contaminated with
foreign substance or paper
particles.
(1)38mm interval : Charge
roller
(2)95mm interval : OPC cycle
1. For item 1 Run OPC Cleaning Mode Print
4-5 times repeatedly to remove
excess toner. Especially check
for foreign substances on the
OPC surface Clean with a clean
gauze moistened with IPA
Isopropyl Alcohol) take care not
to damage the OPC surface.
2. If white spots occur in a black
image at intervals of 95mm,
or black spots occur
elsewhere, the OPC drum is
damaged or foreign
substance is stuck to the
surface.
Never use other forms of alcohol.
3. If a black and white or
graphic image is partially
broken at irregular intervals,
the transfer roller's life has
been expired or the transfer
voltage is abnormal.
Recycled product
• Poor appearance of 1. Poor appearance of the toner
cartridge.
(a)Check for damage to label
• Dirty or rough
and if different materials are
printouts.
used.
(b)Check the appearance of
• Bad background in
parts of the toner cartridge,
the image.
such as frame, hopper, screws
2. Unclean and rough printouts.
(a)Check that the terminals
(contact point) of the toner
cartridge and the set are clean.
(b)Check that the terminals
(contact point) of the toner
cartridge and the set are not
damaged.
2. For Item 2 If running OPC Cleaning Mode
Print 4-5 times does not resolve
the problem
: at intervals of 37.7mm - place
: at intervals of 75.5mm – clean
OPC drum.
3. For item 3 - Change the transfer
roller because the life of the
transfer roller has expired.
(Check the transfer voltage and
readjust if necessary.)
1. For Item 1 the cartridge is judged
to be a recycled product (a) If there is any evidence of
disassembling the toner cartridge.
(b) If materials other than normal
parts of the toner cartridge are
added or substituted.
2. Clean all HV contacts. If the
problem persists replace the
cartridge.
Note If the cartridge is judged to be
recycled then these types of
problems can occur when the
toner cartridge is recycled over
2 times.
If ‘nearly empty’ cartridges are
collected for re-use this is
judged as recycling the toner
cartridge.
7-26
Service Manual
Samsung Electronics
Troubleshooting
Fault
Ghost & Image
Contamination
Signs
Cause & Check
Solution
• The printed image
1. The printed image is too light
is too light or dark,
or dark, or partially
or partially
contaminated black.
contaminated black.
(a) Check if foreign substance
or toner are stuck to the
• Totally
terminals (point of contact)
contaminated black.
of the toner cartridge or set.
(Black image
(b) Check if the terminal
printed out)
assembly is normal.
1. All of Items 1, 2, 3
(a) Clean the contacts on the
toner cartridge.
(b) Clean the contact points on
the set.
(c) If the terminal assembly is
damaged repair or replace
the terminals in the set or
replace the cartridge
• The density of
printouts is too dark
and ghost occurs.
2. In Item 2
This is particularly related to
problems with the charge roller
contact. Pay close attention to
the charge roller contacts.
2. Totally contaminated black.
(Black image printed out)
(a) Check if foreign
substances are stuck to
the terminal (point of
contact) of the toner
cartridge or set.
assembly is normal.
(Especially check the
charge roller terminal.)
3. In Item 3
This is particularly related to
problems with the developer
bias voltage contact. Pay close
attention to the charge roller
contacts.
3. The printed image is dark and
ghost occurs.
(a) Check if foreign
substances are stuck to
the terminal (point of
contact) of the toner
cartridge or set.
assembly is normal.
(Especially check the
developer roller terminal.)
Service Manual
Samsung Electronics
7-27
Troubleshooting
7.8 Software Problems – Causes and Solutions
7.8.1 The printer is not working (1)
• Description
While Power turned on, the printer is not working in the printing mode.
Check and Cause
Solution
1. Run Self-Test Mode: using the menu buttons print the
test page. (Menu, Enter, Enter).
1. If the test print works that means there are no
problems in the printer itself. If the test printing does
not work that means the printer is faulty and the
problem is not due to computer software or driver
settings.
2. Check that the PC and the printer are properly
connected and that the toner cartridge installed
correctly.
2. Replace the printer cable. If the problem is not
solved even after the cable is replaced, check the
amount of the remaining toner. (refer to Toner
Cartridge Service 7-6, Page 7-25)
3. Printing is not working in the Windows.
3. Check that the connection between PC and printer
port are correcct. If you use windows, check that the
printer driver in the controller is set up correctly set
up, the correct port is selected and ‘Use On-line’ is
selected in the driver. If the printer driver is properly
set up try printing a test page from the driver properties. Check in which program printing is not working.
Try opening ‘Memo Pad’ and printing. If the printer
is not working in a certain program, adjust the setup
within that program.
Sometimes, the printout is normal within the
Windows basic programs, but it's not working in a
particular program. In this case, uninstall and reinstall the new driver. If the printer is not working in
the Windows basic programs and you are printing
using the parallel port check the port setting in
CMOS is on ECP and that the address is IRQ 7
and 378 (for parallel port 1). Try using USB instead
of parallel – or vice versa.
4. Check that the printer cable is directly connected to the
printer.
4. If you have other devices that need to share the
printer port try temporarily disconnecting these
devices 9and perhaps even uninstalling their drivers) to ensure the printer works by itself. If you are
using a USB hub try connecting directly to the back
of the PC instead.
7-28
Service Manual
Samsung Electronics
Troubleshooting
7.8.2 The printer is not working (2)
• Description
After receiving the print command there is no response at all or print speed is low
due to wrong setup of the environment rather than malfunction of the printer itself.
Check and Cause
Solution
1. Ensure you have sufficient free hard disk space for the
temporary work files created during printing.
1. Not working with the message 'insufficient printer
memory' means there is a hard disk space problem
rather than a printer RAM problem. In this case provide more space on the hard disk. Secure more
space using the disk utilities program.
2. Printing error occurs even if there is enough space in
the hard disk.
2. The connection of the cable and printer port is not
correct. Check that the cable is properly connected
and if you are using the parallel port check that the
port settings in CMOS is correct.
3. Check the parallel-port-related items in the CMOS
Setup.
3. For the printer port, Select ECP. SPP and normal
normal modes support 8-bit data transfer, while
ECP Mode supports 12-bit data transfer.
4. Reboot the system to print.
4. If the regular font is not printing, the cable or the
printer driver may be defective.
Turn the PC and printer off, and reboot the system
to print again. If not solved, double-click the printer
in my computer If the regular fonts are not printed
this time again. the cable must be defective so
replace the cable with new one.
Service Manual
Samsung Electronics
7-29
Troubleshooting
7.8.3 Abnormal Printing
• Description
Printing does not work – even after replacing the cable
Printer does not work at all or strange fonts are printed,
Check and Cause
Solution
1. Set up the parallel port using CMOS SETUP.
1. Ensure that ECP (best) or SPP is selected in the
CMOS (BIOS) setup.
2. Printer Driver Error.
2. Ensure that the correct driver is loaded. Use the
driver supplied on the CD or downloaded from the
Samsung web site. DO NOT use the Microsoft
driver supplied with the Windows operating system.
If the printer is a GDI or SPL type printer ensure that
ALL OTHER GDI or SPL drivers are uninstalled as
Windows allows only 1 of this type of driver to be
loaded.
3. Error message “insufficient memory”.
(The printing job sometimes stops due to insufficient
virtual memory, this is caused by insufficient space on
the hard disk.)
3. Delete any unnecessary files to secure enough
space on the hard disk and start the print job again.
7-30
Service Manual
Samsung Electronics
Troubleshooting
7.8.4 SPOOL Error
• Description
SPOOL (simultaneous peripheral operations online) is the process Windows uses to
manage print jobs. Jobs are processed and then stored on the hard disk until the printer is
ready to accept them
Check and Cause
Solution
1. Insufficient space on the hard disk in the directory
assigned for the basic spool.
1. Delete any unnecessary files to provide more space
for spool storage.
2. If previous printing errors were not solved.
2. There may be files from previous failed print jobs on
the hard disk with the name in the form ‘*.jnl’.
Delete these files and Reboot Windows to restart
the printer.
3. There may be conflict with other drivers or programs.
3. Shut down all other programs except the current
one, if possible.
4. When an application program or the printer driver is
damaged.
4. Delete the printer driver completely and reinstall it.
5. When some files related to the OS are damaged or
virus infected.
5 After rebooting the computer, check for viruses,
restore the damaged files and reinstall the
application program which is not working properly.
6. Memory is less than suggested.
6. Add up more memory to the PC.
How to delete the data in the spool manager.
In the spool manager, the installed drivers and the list of the documents waiting to be printed are shown.
Select the document to be deleted and check delete in the menu.
If the job you are deleting is the current job when you delete the job data that has already been transferred to
the printer’s memory will still be printed. If there is a problem with the printer (out of toner, offline, out of paper
etc.) the job may take a long time to delete as it must wait for a time out.
Service Manual
Samsung Electronics
7-31
Troubleshooting
7.9 Network Problem Troubleshooting
7.9.1 General Problems
7-32
Problem
Solution
Incorrect setup can cause network errors.
Possibly the parameters in PortThru (the network card) are corrupted. Restart the system and reset the printer network settings to factory defaults using the printer front panel or by using SyncThru on
your computer.
SNMP Manager cannot access the printer.
Using the SNMP manager computer try pinging the printer. If it
does not succeed there must be a problem with network connectivity between the SNMP manager computer and PortThru. If ping succeeds verify that community names entered into the PortThru settings are spelled correctly and have sufficient permissions.
The printer does not obtain an IP address
from a BOOTP, RARP or DHCP server.
If there is an IP address server on your network ensure that there
are no VLAN, Access Control Lists or other network settings preventing communication. Remember these protocols are generally
not routable unless specifically setup in a router.
Where no address server exists use SyncThru or the control panel
on the printer to select "Static" IP Address Assignment Method" in
TCP/IP tab. You should set IP address, Subnet Mask and Default
Gateway in the printer using SyncThru, printer control panel or
browser methods (see the user guide).
Print server does not print using TCP/IP protocol.
1. Check that TCP/IP protocol is installed and properly configured in
your PC.
2. Check whether your PC is on the same network with print server
(IP addresses and subnet masks must be properly set in the PC
AND in the printer).
Unable to print in a NetWare environment.
Use SyncThru to see if PortThru indicates that queue is serviceable. If not, the login permissions may have changed or the configuration information for queues, printers and print servers may have
been changed. Verify using PCONSOLE and NWADMIN that the
configuration is correct and check the job queue to see if the print
job exists. Check that NetWare is enabled on PortThru. Check that
the Check Job very is configured on PortThru.
The name of printer is not displayed when
adding a port and the printer doesn't function.
1. Check that the protocol settings on your computer are correct.
2. Assign an IP Address to PortThru using the front panel,
SyncThru or browser methods (see the user guide).
Service Manual
Samsung Electronics
Troubleshooting
7.9.2 Windows Problems
Problem
Solution
After installing PortThru the print server name
is not displayed under New Print Server in
SyncThru.
1. Verify that the printer power switch is turned on and the 'READY'
message is displayed on the printer front panel.
2. Verify that the LAN cable is plugged into the PortThru card.
3. There are 2LEDs on the PortThru card. One should flash irregularly
and the other should be on. If this is not the case ensure that the
network card is properly installed and the PCB an cable connectors
make a good connection. If the problem continues check the network
cable / socket by using a different cable or socket. If the problem
continues replace the network card.
4. Confirm that the print server and the PC which searches for the
New Print Server is on the same LAN (correct IP and subnet
mask settings). If you want to search for a New Print Server your
PC and the print server should be on the same LAN.
The print server name is displayed, but the test
page is not printed.
Using the front panel menus print the Network configuration. If the
Network menu is not displayed or the configuration page is not
printed turn off the printer, ensure the network card is properly fitted
then turn it back on and try again. If the problem continues replace
the network card.
SyncThru indicates that firmware upgrade is
complete but when the network configuration
is printed the software version has not changed.
Before attempting to upgrade firmware ensure that computer and
printer can communicate using a Ping command.
SycThru is unable to automatically detect
the printer.
1. Check that the LAN cable is connected to the printers. If an IP
address is assigned to the computer and printer ensure that the
Ping command can see the printer.
If an IP address is not allocated to the printer or it is in a different
LAN segment then ensure that either IPX/SPX or DLC/LLC protocols are enabled on the computer.
2. Print the network configuration. If the TCP/IP or Network protocols are disabled in the printer either use the front panel to reenable them or ensure that DLC/LLC protocol is installed in the
computer.
3. In SyncThru use the Settings / Protocol Selection menu option to
select either TCP/IP or IPX protocols and then use the
View/Refresh option to scan the network again.
4. Ensure that the network cable and wall socket are functioning
correctly.
5. Ensure that the version of SyncThru is the same as or newer
than the version supplied with the printer.
6. Ensure that there is no router between the printer and the
computer as SyncThru will not work through a router.
7. Ensure there are no Switch or Router VLAN or Access Control
Lists which are blocking communication between the printer and
the computer.
Note Windows XP does not support DLC/LLC protocols.
The printer does not print via a
network connection.
1. Connect the printer using a Parallel or USB cable and ensure
that the computer can print. If not check that the printer drivers
are installed correctly
2. If the printer can print via a local connection check Printer
Properties / Ports and ensure that a TCP/Ip port has been allocated to the printer.
Service Manual
Samsung Electronics
7-33
Troubleshooting
7.9.3 SyncThru Installation Problems
7-34
Problem
Solution
"File Transfer Error" message appears during
the Installation process.
1. Make sure that any previously installed version of SyncThru is
uninstalled. Restart your PC after uninstalling previous versions.
2. If the problem continues, In Windows 95/98 boot into MS/DOS
mode and delete the "sammon.dll" file in the windows\system
directory the restart Windows and reinstall SyncThru. In Windows
NT stop the spooler service using' Services 'in Control Panel,
delete the "sammon.dll" file in the windows\system32 directory
then restart the spooler service and reinstall SyncThru.
'Unable to add the Port list of Samsung ports'
message appears when you add a port.
Verify that your PC restarts after installing SyncThru.
Service Manual
Samsung Electronics
8. Exploded Views and Parts List (SCX-4720FN/XAA)
8.1 Main Assembly Exploded view
8.2 Rx Drive Ass’y Exploded view
8.3 ADF Assembly Exploded view
8.4 OPE Assembly Exploded view
8.5 Scanner Assembly Exploded view
8.6 Middle Cover Assembly Exploded view
8.7 Frame Ass’y Exploded view
8.8 Fuser Ass’y Exploded view
8.9 MP Assembly Exploded view
8.10 Cassette Ass’y Exploded view
8.11 SCF(Option Cassette Frame) Exploded view
Exploded drawings and service parts lists are given for items which may
be expected to have a higher failure rate.
Where a failure occurs you can identify the part in the exploded diagram
and, using the parts cross reference number, refer to the appropriate parts
list to identify the part number.
Note : Parts numbers given here are correct at the time of publication.
When ordering parts please use the on-line ordering system to check if
there have been any changes to part numbers.
Part Number & Description format.
Part numbers and descriptions are defined according to a company standard. The information below
will help you to understand the part number format and assist when ordering spare parts.
There are two types of Part number format.
number
letter
This format is used throughout Samsung on all product ranges.
Typically it is used for small components and electronic parts.
This format is controlled by individual Samsung Divisions and is used on specific
products, typically for mechanical parts. Type 2 format part numbers fall into 2 categories:
Assemblies consisting of 2 or more parts. Also used for Service manuals,
user guides and diagrams.
Ass’y parts and A/S privately used Parts can be distinguished by the part Code and Description.
They are always Type 2 format. The 2 leading characters indicate private or assembly parts.
1-3
SCX-4520
SCX-4720F
SCX-4520
1-1
SCX-4720F
1-4
1-2
1-2
1
Toner Cartridge
22-8
22-13
21-2
22-5
0
22-9
22-10
22-6
22-4
22-7
22-1
22-3
22-2
21-4
21-3
21-1
20
21
22-12
22-11
7
19-1
15
22
3
19-3
19-4
24
19
10
19-2
18
4
25
6
16
8
17
17-1
5
23
13
2
17-2
27
28
11
26
23-2
28-1
28-1
23-1
14
SCF
8.1 Main Assembly
8.2 RX Drive Assembly
0
8
6
7
1
9
4
2
5
3
4
5
8.3 ADF Assembly
5
5-1
5-2
6
5-3
6-3
5-2
0 : Service Part
6-1
*ELA HOU-ADF_R2
(JC96-03169A)
6-2
ADF ASS’Y
1-2-4
1
1-2-1
1-2
1-2-2
1-2-3
4
1-1
3-4
3-3
3-7
3-8
3-14
3-6
3-18
3-5
2-16
3-11
3-7
3-9
3-15
3-18
3-16
2-3
3-17
3-10
3-16
3-13
3-20
3-21
3-19
2-2
2-4
2-15
3-1
2-6
2-7
3-12
2-5
3-2
3-19
2-8
2-9
3-18
2-15
2
2-17
2-1
2-19
2-22
2-18
2-12
2-10
2-22
2-19
2-20
2-20
2-21
2-14
2-13
3
ADF Assembly Continued.
4-3-2
4-3-3
4-3-4
4-3-5
4 : Service Part
*MEA-COVER PLATEN
(JC-97-02024A)
4-3-1
4-3
4-8
4-6
4-4
4-7
S
4-7
S
4-1
4-4
4-5
4-9
4-2
8.4 OPE Unit Assembly
0
21
20
2
1
19
8
3
5
17
10
4
18
6
16
7
14
9
11
12
13
15
8.5 Scanner Assembly
1-3
1-3-1
1-3-2
1-3-4
1-3-3
0
1-1
1
1-5
1-4
1-5
1-2
2
2-15
2-2
2-15-4
2-15-7
2-15-6
2-15-5
2-9
2-15-3
2-5
2-3
? 2-15-8
2-10
2-11
2-6
2-8
2-15-1
2-13
2-12
2-7
2-16
2-15-2
2-4
2-1
2-14
8.6 Middle Cover Assembly
0
2
5
6
4
1
3
46-2
46-1
47-2
73
50
47-1
46
74
47-3
26
47-4
47
78
75
47-5
29
56
76
45-1
45-3
27-2
27-3
45-2
43
17
39
27-1
67 77
45
44
32
34
27
25
1
42
33
41
40
28
30
21
71
Transfer Roller
24
58
37
38
49
25
20
51
23
31
36
62
5
5
22
61
7
18
5
19
19-1
72
49
19-2
15
65
63-1
55
63-2
1
14
13
69
68
65-4
65-2
63
65-1
6
11
54
65-3
58
61
10
71
16
3
8
70
9
12
4
0
2
ELA HOU-FRAME
Unit Fuser
8.7 Frame Assembly
8.8 Fuser Assembly
0
36
6
12
14
17
34
4
38
1
5
29
37
3
31
29
37
13
32
35
15
30
11
16
33
20
23
19
18
21
25
28
24
22
9
8
36
10
7
27
38
26
8.9 MP Assembly
0
26
11
12
28
14
2
23
14
23
25
1
21
7
25
3
30
18
9
24
31
29
10
16
20
17
13
6
15
5-1
5-3
5
27
19
4
5-2
19
8.10 Cassette Assembly
0
12
14
13
6
16
4
6-4
6-3
6-2
6-1
15
5
3
7
5
2
10
11
1
17
8
42
1
39-3
38
39-8
0
40
39-6
39-10
39-7
39-4
39-2
28
39-1
39-5
1-3
20
21
39-9
1-4
34
23
39
22
24
19
18
37
17
11
15
13
33
32
9
10
16
14
6
7
31
12
8
25
30
36
34
2
35
41
27
5
28
3
26
4
29
΁ΒΣΥΤ͑ͽΚΤΥ
Model code : SCX-4720FN/XAA
SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE
Draw#
Part Code
Description
DNA : DELIVERY
not AVAILABLE
Location
SNA
8.1 Main Assembly Exploded view
8.1-1
8.1-1-1
8.1-1-2
8.1-1-3
8.1-1-4
8.1-2
8.1-3
8.1-4
8.1-6
8.1-7
8.1-8
8.1-9
8.1-10
8.1-11
8.1-13
8.1-14
8.1-15
8.1-16
8.1-17
8.1-17-1
8.1-17-2
8.1-18
8.1-19
8.1-19-1
8.1-19-12
8.1-19-2
8.1-19-3
8.1-19-4
8.1-20
8.1-21
8.1-21-1
8.1-21-2
8.1-21-3
8.1-21-4
8.1-22
8.1-22-1
8.1-22-2
8.1-22-3
8.1-22-4
8.1-22-5
8.1-22-6
8.1-22-7
8.1-22-8
8.1-22-9
8.1-22-10
8.1-22-11
8.1-23
8.1-23-1
8.1-23-2
8.1-24
8.1-25
8.1-26
8.1-27
8.1-28
8.1-28-1
8.1-28-2
JC96-03730A
JC96-03169A
JC96-03731A
JC63-00496A
JC96-03172D
JC61-00906A
JC96-03078A
JC59-00018B
JC44-00070A
JC92-01731A
JC63-00508A
JC39-00395A
JC97-01943A
JC61-00693A
JC92-01733A
JC63-00499A
JC96-03132B
JC39-00355A
JC97-01917A
JC66-00703A
JC66-00395A
JC96-03247A
JC97-02043A
JC63-00497A
6003-000196
JC67-00068A
JC72-01339A
6003-000196
JC97-02020A
JC96-03185A
JC63-00500A
JC63-00501A
3001-001591
6003-000264
JC97-02019A
JC63-00505A
JC64-00154A
JC61-00953A
JC63-00447A
JC70-00478A
JC70-00479A
JC63-00446A
JG66-40003A
JC63-00506A
JC63-00444A
JG61-70549A
JC97-02018A
JC63-00503A
JC63-00504A
JC39-00240C
JC39-00375A
JC96-03210A
JC31-00025A
JC96-03586A
JC61-00809A
JC92-01700B
ELA HOU-SCAN_R2P SEC;SCX-4720FN,USA,-,
ELA HOU-ADF R2_SEC;SCX-4720F,SEC,-,ADF A
ELA HOU-OPE R2P_SEC;SCX-4720FN,USA,-,O
COVER-M-OPE FRONT;SCX-4720F,HIPS,-,434.5
ELA HOU-PLATEN;SCX-4720FN,SEC,-,-,-,-,FRAME-M-BASE R2;SCX-4920N,PC+ABS(NH-1000
ELA UNIT-RX DRIVE;SCX-4920N,DELL,-,DRIVE
UNIT-LSU HUMMINGBIRD2;SCX-4920N,-,-,600D
SMPS-V1(XAA);SCX-4920N,-,AC/DC,45.7W,100
PBA MAIN-CONTROLLER;SCX-4720FN,-,-,-,-,SHIELD-P-CONTROLLER_SEC;SCX-4720F,SECC,0
CBF HARNESS-LSU;SCX-4920N,#26,UL1061 / U
MEA UNIT-SHIELD ENGINE;SCX-4920N,DELL ,BRACKET-P-INLET, ROCKY;SCX-4216F,SECC,T1
PBA SUB-LIU_DOMESTIC;SCX-4720FN,SEC,-,LI
COVER-M-SIDE R_SEC;SCX-4720F,HIPS,-,398.
ELA UNIT-MP_R2;SCX-4720F,SEC,-,MP,-,-,CBF HARNESS-MOTOR;SCX-4920N,CBF,UL1061,4
MEA ETC-TR;SCX-4920N,DELL,-,TR ASS'Y,-,ROLLER-TRANSFER R2;SCX-4920N,SUM24L+NBR,
GEAR-TRANSFER;ML-1710,POM(M90-44),-,-,-,
ELA HOU-COVER MIDDLE;SCX-4720F,-,ROCKY2,
MEA-COVER MID FRONT;SCX-4720F,SEC,-,COVE
COVER-M-MID FRONT_SEC;SCX-4720F,HIPS,-,4
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRC
CAP-M-SUB ACTUATOR;ML-2250,HIPS,-,35,28.
PMO-M-SUB ACTUATOR;ML-2250,POM,-,46.3*20
MEA-CASSETTE;SCX-4720F,SEC,ROCKY2,CASSET
ELA HOU-COVER SIDE L;SCX-4720F,SEC,ROCKY
COVER-M-SIDE L_SEC;SCX-4720F,HIPS,-,398.
COVER-M-DIMM_SEC;SCX-4720F,HIPS,-,251.9,
SPEAKER;0.4W,8OHM,87DB,480HZ
SCREW-TAPTITE;PWH,+,B,M3,L6,ZPC(YEL),SWR
MEA-COVER FRONT;SCX-4720F,SEC,ROCKY2,COV
COVER-M-FRONT_SEC;SCX-4720F,HIPS,-,431.1
KNOB-M-LOCKER_SEC;SCX-4720F,HIPS,-,84.1,
HOLDER-M-LOCKER_SEC;SCX-4720F,HIPS,-,113
TRAY-M-EXIT_MP;ML-2250,HIPS,-,235,119,-,
ADJUST-M-MP L;ML-2250,ABS,-,82,128.4,-,ADJUST-M-MP R;ML-2250,ABS,-,82,128.4,-,TRAY-M-COVER_MP;ML-2250,HIPS,-,260.1,127
GEAR-PINION;SF4000,POM,WHT,M1,Z16
TRAY-M-CASE_MP_SEC;SCX-4720F,HIPS,-,284.
TRAY-M-LINK_MP;ML-2250,PC,2,74.9,9.3,-,SPRING ETC-CIS(C2);SF4400,SUS304WPB,D11.
MEA-COVER REAR;SCX-4720F,SEC,ROCKY2,COVE
COVER-M-REAR_SEC;SCX-4720F,HIPS,-,402.8,
COVER-M-FACE UP_SEC;SCX-4720F,ABS,-,328.
CBF HARNESS-ENGINE;SCX-4920N,CBF,UL1061,
CBF HARNESS-LSU GND;SCX-4920N,CBF,UL1007
ELA HOU-FUSER LV R2;SCX-4720F,SEC,-,FUSE
FAN-DC;AD0624MSA70GL(R1)DOL,CLP-500,PBT+
ELA HOU-EMBEDDED_MAC;SCX-4920N,SAMSUNG,BRACKET-_M_NPC;MLC-500,SECC,T0.8,-,-,-,PBA SUB-NPC_PRT;SCX-4720FN,SEC,KOREA,10/
8.2 Rx Drive Ass’y Exploded view
͢
K2929
Z3337
B0081
D4033
L7044
S7050
Z1040
L7002
E2098
B4027
Z2167
K3155
M2053
Z6247
T3013
G0448
Z2062
Z2417
Z2200
A0004
C4045
Z2269
Z2166
Z2181
Z2434
D0014
H4050
T4113
K2018
K2019
T4133
G0035
T4136
T4137
C5029
Z2437
Z2220
Z2186
H1070
F4031
F0002
B0005
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SNA
SNA
SA
SA
SA
SA
SA
SA
SNA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SNA
SNA
SA
Draw#
8.2-0
8.2-1
8.2-2
8.2-3
8.2-4
8.2-5
8.2-6
8.2-7
8.2-8
8.2-9
Part Code
JC96-03078A
JC61-00891A
JC66-00388A
JC66-00706A
JC66-00389A
6031-000023
JC61-00916A
JC66-00390A
JC66-00392A
JC31-00037A
Description
ELA UNIT-RX DRIVE;SCX-4920N,DELL,-,DRIVE
BRACKET-P-GEAR MAIN;SCX-4920N,SECC,1.6,2
GEAR-RDCN 53/26;ML-1710,POM(DE390PM),-,5
GEAR-RDCN 113/33;SCX-4920N,POM(DELIN8903
GEAR-RDCN 57/18;ML-1710,POM(M90-44),-,57
WASHER-PLAIN;-,ID5.9,OD10.0,T0.5,BLK,POL
BRACKET-P-MOTOR MAIN R2;SCX-4920N,SECC,1
GEAR-RDCN 103/41;ML-1710,POM(NW-02),-,10
GEAR-RDCN 90/31;ML-1710,POM(NW02),-,90/3
MOTOR STEP-MAIN;M55SP-2NK,SCX-4920N,1.2A
DNA : DELIVERY
not AVAILABLE
Location
SNA
D4033
B4055
G0393
G0381
G0394
W0001
M2048
G0396
G0380
M2159
SA
SA
SA
SA
SA
SNA
SA
SA
SA
SA
K2929
K3515
Z2173
K3572
SA
SA
SA
SA
SA
SA
SA
SNA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SNA
SA
SA
SA
SA
SA
SNA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SNA
SA
SNA
SNA
SA
SA
SNA
8.3 ADF Assembly Exploded view
8.3-0
8.3-1
8.3-1-1
8.3-1-2
8.3-1-2-1
8.3-1-2-2
8.3-1-2-3
8.3-1-2-4
8.3-2
8.3-2-1
8.3-2-2
8.3-2-3
8.3-2-4
8.3-2-5
8.3-2-6
8.3-2-7
8.3-2-8
8.3-2-9
8.3-2-10
8.3-2-12
8.3-2-13
8.3-2-14
8.3-2-15
8.3-2-16
8.3-2-17
8.3-2-18
8.3-2-19
8.3-2-20
8.3-2-21
8.3-2-22
8.3-3
8.3-3-1
8.3-3-2
8.3-3-3
8.3-3-4
8.3-3-5
8.3-3-6
8.3-3-7
8.3-3-8
8.3-3-9
8.3-3-10
8.3-3-11
8.3-3-12
8.3-3-13
8.3-3-14
8.3-3-15
8.3-3-16
8.3-3-17
8.3-3-18
8.3-3-19
8.3-3-20
JC96-03169A
JC97-02022A
JC63-00450A
JC97-02137B
JB73-00052A
JC61-00893A
JC61-00387A
JC63-00373A
JC96-03171A
JC63-00370B
JC92-01618A
JC63-00372A
JC66-00460A
JC66-00560A
JC72-01320A
JC72-01010A
JC72-01011A
JB61-00076A
JC70-10467A
JC66-00559A
JC75-00095A
JC72-00752A
JB72-00819A
JC39-00351A
JC66-00310A
6044-000159
JC61-00712A
JC39-00187A
JC70-00225A
JC61-00548A
JC96-03065A
JC61-00892A
JC31-00036A
JB66-00101A
JB72-00844A
JC66-00322A
6044-000159
JC66-00458A
JC66-00456A
JC66-00457A
JC66-00454A
JC66-00455A
JC66-00556A
JC66-00557B
6031-001511
JB70-00070A
6031-000019
JC39-00363A
6044-000125
6003-000269
6031-001511
ELA HOU-ADF R2_SEC;SCX-4720F,SEC,-,ADF A
MEA-ADF UPPER R2;SCX-4720F,SEC,-,ADF UPP
COVER-M-ADF UPPER DELL;SCX-4920N,HIPS,2.
MEA-HOLDER PAD ADF;SCX-4520,-,-,HOLDER A
RMO-ADF RUBBER;SCX-1110F,SILICON RUBBER,
HOLDER-M-PAD ADF;SCX-4920N,POM,1.5,44.9,
SPRING ETC-PAD;ML-9400W,SUS304WPB,PI0.5,
SHEET-ADF HOLDER;SCX-4920,PC,0.2,18,35.4
ELA HOU-ADF LOWER;SCX-4720F,SEC,-,ADF LO
COVER-M-ADF LOWER SEC;SCX-4720F,ABS,2.5,
PBA SUB-ADF;SCX-4920N,DELL,-,ADF,-,-,-,1
GROUND-P-ADF R2;SCX-4920N,C5210P,0.2,8,1
SHAFT-M-FEED GEAR 38;SCX-4216F,POM,-,D5.
ROLLER-DRIVE;SCX-4216F,CR+SUM24L,14,-,-,
PMO-ACT EMPTY ADF;SCX-4920N,ABS,GRAY,-,PMO-ACTUATOR REGI SENSOR;SCX-4216F,PC,BL
PMO-ACTUATOR SCAN SENSOR;SCX-4216F,PC,BL
SPRING ETC-TORSION DOC (CC2-F);SCX-1110F
IPR-GROUND_ROLLER;SCF-ML,SUS301,-,T0.2,ROLLER-EXIT;SCX-4216F,CR+SUM24L,14,-,-,MEC-BRUSH ANTISTATIC;ML-6060A,SEC,NTR
PPR-WHITE BAR SHEET;SCX-5100,PET,WHT,T0.
PMO-BUSH;SCX-1110F,POM,NTR,-,-,-,-,-,CBF HARNESS-ADF;SCX-4720F,CBF,UL2835-15C
GEAR-AGITATOR-2;SCX-5100,POM(M90-44),0.6
RING-C;ID3,OD7,T0.6,PASS,STSC
GUIDE-STACKER SUB;SCX-4216F,PC+ABS,2.5T,
CBF HARNESS-ADF ROLLER GND;SCX-5100,WIRE
IPR-BRKT WHITE BAR;SCX-5150,SECC,-,T1.0,
SPRING ETC-WHITE BAR;SCX-5312F,SUS304WPB
ELA HOU-ADF MOTOR;SCX-4920N,DELL,-,ADF M
BRACKET-P-GEAR ADF;SCX-4920N,SECC,1.2,10
MOTOR STEP-ADF;M42SP-13NK,SCX-4920N,0.6A
GEAR-CLUTCH 29;SCX-1110F,POM(DELIN500P),
PMO-WHITE CLUTCH SUB 29;SCX-1110F,POM(F2
GEAR-CLUTCH 39;SCX-5150,POM,M0.6,Z39,-,W
GEAR-IDLE 35 ADF;SCX-4216F,POM,M0.6,Z35,
GEAR-40/21 ADF;SCX-4216F,POM,M0.6,Z40/21
GEAR-SWING 31/20 ADF;SCX-4216F,POM,M0.6,
LINK-M-SWING ADF;SCX-4216F,DELIN 500CL,GEAR-58/25 ADF;SCX-4216F,POM,M0.6,Z58/25
IMPELLER-ADF;SCX-4216F,NYLON66,-,-,-,-,V
GEAR-REMOVE ADF(XRX);SCX-4216F/XRX,POM,M
WASHER-PLAIN;POLYSLIDE,M5,ID5.2,OD10,T0.
IPR-WASHER WAVE;SF-4750C,SUS301,-,0.1T,WASHER-PLAIN;-,ID6.1,OD8.5,T0.1,BLK,POLY
CBF HARNESS-ADF GND;SCX-4920N,CBF,UL1007
RING-E;ID4,OD9,T0.6,PASS,STSC
SCREW-TAPTITE;BH,+,-,S,M3,L6,ZPC(YEL),SW
WASHER-PLAIN;POLYSLIDE,M5,ID5.2,OD10,T0.
ͣ
S0028
K2032
Z2170
K3231
S3071
Z4274
S1049
M0022
S5050
H1029
H1031
K3289
Z4294
M2000
R0004
Draw#
8.3-3-21
8.3-4
8.3-4-1
8.3-4-2
8.3-4-3
8.3-4-3-1
8.3-4-3-2
8.3-4-3-3
8.3-4-3-4
8.3-4-3-5
8.3-4-4
8.3-4-5
8.3-4-6
8.3-4-7
8.3-4-9
8.3-5
8.3-5-1
8.3-5-2
8.3-5-3
8.3-6
8.3-6-1
8.3-6-2
8.3-6-3
Part Code
JC61-00387A
JC97-02024A
JC63-00374B
JC63-00209A
JB97-01544B
JB72-01166B
JB72-01171B
JG66-40003A
JB72-01170B
JF70-10616A
JC61-00011A
JG72-40663A
JF70-40521B
JC97-01707A
JC66-00558A
JC97-02023A
JC63-00498A
JB72-00843A
JC66-00726A
JC97-01962A
JC61-00963A
JB66-00103A
6044-000159
Description
SPRING ETC-PAD;ML-9400W,SUS304WPB,PI0.5,
MEA-COVER PLATEN R2;SCX-4720F,SEC,-,COVE
COVER-M-PLATEN SEC;SCX-4720F,HIPS,2.5,32
SHEET-WHITE SPONGE;SCX-4216F,PC SHEET+SP
MEA-TX STACKER(SEC);SCX-1150F,SEC,-,TX S
PMO-TX STACKER(SEC);SCX-1150F,HIPS,WHITE
PMO-DOC GUIDE(L);SCX-1150F,HIPS,WHITE,-,
PMO-DOC GUIDE(R);SCX-1150F,HIPS,WHITE,-,
IPR-WASHER SPRING CU;CF3400,SUS301-CSP,SPRING ETC-FEED;SF-5100,SUS304WPB,0.6,-,
PMO-ROLL PINCH;SF5500,POM(DERLIN 500P),B
ICT-SHAFT PINCH;FX2200,STSC304WPA,-,D2.6
MEA UNIT-HINGE;SCX-4216F,SEC,-,HINGE ,-,
SHAFT-IDLE FEED;SCX-4216F,SUS303F,59.5,2
MEA-COVER OPEN R2;SCX-4720F,SEC,-,COVER
COVER-M-ADF OPEN;SCX-4720F,HIPS,2.5,244,
PMO-GUIDE PAPER;SCX-1110F,HIPS,IV21,-,-,
DAMPER-PICK UP ADF;SCX-4520,URETHANE FOA
MEA UNIT-PICKUP DELL;SCX-4920N,DELL,-,PI
STOPPER-M-PICKUP ADF;SCX-4920N,POM(DENLI
GEAR-ADF 38;SCX-1110F,POM(DELIN500P),0.6
DNA : DELIVERY
not AVAILABLE
Location
SNA
S0028
P5006
Z2218
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SNA
SA
SA
Z5024
Z5093
G2168
G0035
G2174
H3041
F6212
Z2419
Z2213
P5164
B6030
8.4 OPE Assembly Exploded view
8.4-0
8.4-1
8.4-2
8.4-3
8.4-4
8.4-5
8.4-6
8.4-7
8.4-8
8.4-9
8.4-10
8.4-11
8.4-12
8.4-13
8.4-14
8.4-15
8.4-16
8.4-17
8.4-18
8.4-19
8.4-20
8.4-21
JC96-03731A
JC63-00495A
JC64-00171D
JC64-00054C
JC64-00055A
JC64-00056D
JC64-00057E
JC64-00061A
JC64-00059C
JC64-00155A
JC64-00157A
JC73-00189A
JC73-00191A
JC92-01625A
JC73-00190A
JC64-00058A
JC64-00060C
JC64-00156A
JC64-00053D
JC72-00275B
JC68-00651G
JG74-10543A
ELA HOU-OPE R2P_SEC;SCX-4720FN/XAA,USA,COVER-M-OPE SEC;SCX-4720F,HIPS,-,444.5,1
WINDOW-LCDR2_PLUS_SEC;SCX-4720FN,PC,0.5,
KEY-M_COPY_R2;SCX-4720F,ABS,-,HB,G71335,
KEY-M-STOP;SCX-4216F,HIPS,-,HB,ORANGE,-,
KEY-M_SCROLL_R2;SCX-4720F,ABS,-,HB,G7133
KEY-M_START;SCX-4720F,HIPS,-,HB,BLUE,-,KEY-M-TOLL SAVE;SCX-4216F,ACRYL,-,HB,MIL
KEY-M_RESOLUTION_R2;SCX-4720F,ABS,-,HB,G
KEY-M-DIRECT PRINT;SCX-4720F,ABS,23.3*15
KEY-M-SCAN TO;SCX-4720F,ABS,16*16*9,HB,RUBBER-COPY/SCROLL;SCX-4720F,SILICON,159
RUBBER-TELL/FAX_SEC;SCX-4720F,SILICON,12
PBA SUB-OPE;SCX-4720FN,SEC,-,OPE,-,-,-,4
RUBBER-ONE TOUCH;SCX-4720F,SILICON,114*7
KEY-M-TONER SAVE;SCX-4216F,ACRYL,-,HB,MI
KEY-M_FAX_R2;SCX-4720F,ABS,-,HB,G71335,KEY-M-SHIFT;SCX-4720F,ABS,16.5*9.9*8.7,H
KEY-M_TEL_R2;SCX-4720F,ABS,-,HB,G71335,PMO-KEY OT;SF-555P,HIPS,LIGHT GRAY,-,HR1
LABEL(P)-ONE TOUCH;COMMON,SEC,ART 120G,0
MPR-COVER ADRESS;SF4400,PC,84.5X76XT0.38
K0011
K0059
K0024
K0052
K0067
K0022
K0037
K0054
R1112
R1126
R1121
K0068
K0013
K0025
K0031
K0194
L0120
SA
SNA
SA
SA
SA
SA
SA
SNA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
8.5 Scanner Assembly Exploded view
8.5-0
8.5-1
8.5-1-1
8.5-1-2
8.5-1-3
8.5-1-3-1
8.5-1-3-2
8.5-1-3-3
8.5-1-3-4
8.5-1-4
8.5-2
8.5-2-1
8.5-2-2
8.5-2-3
JC96-03172D
JC97-02025A
JC63-00494A
JC01-00001A
JC97-02026A
JC63-00152E
JC74-00021A
0203-001266
JB68-00644A
JB70-00148A
JC96-03173C
JC63-00493A
JC96-02759B
JC39-00367A
ELA HOU-PLATEN;SCX-4720FN,SEC,-,-,-,-,MEA-SCAN UPPER R2;SCX-4720F,SEC,-,SCAN U
COVER-M-SCAN UPPER SEC;SCX-4720F,ABS,-,4
GLASS-SCAN;329.9*247.5,2.8,MEA-SCAN DUMMY R2;SCX-4720F,SEC,-,SCAN D
COVER-M-SCAN DUMMY R2;SCX-4720F,HIPS,-,MCT-GLASS ADF;SCX-4216F,GLASS,238.4*19.1
TAPE-DOUBLE FACE;3M9448HK,T0.16,W4,L280,
LABEL(P)-SHADING;COMMON,YOOPO PAPER ,T0.
IPR-HOLDER GLASS;SCX-1110/XRX,SUS304,-,1
ELA HOU-SCAN LOWER;SCX-4720FN,SEC,-,-,-,
COVER-M-SCAN LOWER SEC;SCX-4720F,ABS,-,4
ELA HOU-CCD MODULE;SCX-6320F,XEROX,USA,6
CBF SIGNAL-CCD FFC;SCX-4920N,24PIN,FFC,6
ͤ
K3612
Z2229
G1004
D2026
G1009
Z2226
C5014
C5008
SA
SA
SA
SA
SNA
SA
SA
SNA
SA
SA
SA
SA
SA
SA
Draw#
8.5-2-4
8.5-2-5
8.5-2-6
8.5-2-7
8.5-2-8
8.5-2-9
8.5-2-10
8.5-2-11
8.5-2-12
8.5-2-13
8.5-2-14
8.5-2-15
8.5-2-15-1
8.5-2-15-2
8.5-2-15-3
8.5-2-15-4
8.5-2-15-5
8.5-2-15-6
8.5-15-7
8.5-16
Part Code
JB70-00154A
JB70-00145A
JB72-00764A
JB72-00763A
JB96-01381A
JB61-00059A
6602-001067
JC72-00755A
0604-001095
6107-001135
JC61-00894A
JC96-03069A
JC61-00895A
JB31-00011A
JC66-00530A
JB66-00083A
JC66-00531A
JB72-00764A
6044-000125
JC39-00362A
Description
ICT-INSERT SHAFT;SCX-1110/XRX,SUM24L,5,ICT-SHAFT CCD;SCX-1110/XRX,SUM24L,8,-,-,
PMO-HOLDER BELT;SCX-1110/XRX,-,POM,WHT,PMO-PULLEY;SCX-1110/XRX,-,POM,WHT,-,-,ELA UNIT-CORE;SCX-1100,SAMSUNG,CORE ASS'
SPRING ETC-BELT;SCX-1110/XRX,SUS304WP,¥Õ
BELT-TIMING GEAR;HIBER GLASS,T3.2,T80-40
PMO-LEVER SENSOR;SCX-5100,POM,BLK,-,-,HB
PHOTO-INTERRUPTER;TR,90%,150mW,DIP-4,BK
SPRING-CS;SUS304 WPB,-,PI0.3,-,L14,-,-,I
HOLDER-M-CCD;SCX-4920N,HIPS,2,43.6,38.2,
ELA HOU-SCAN MOTOR;SCX-4920N,DELL,-,SCAN
BRACKET-SCAN MOTOR R2;SCX-4920N,PC GF10%
MOTOR STEP-SCAN;M42SP-4TKC,SCX-1110/XRX,
GEAR-REDUCTION73/37;SCX-6320F,POM(M90-44
GEAR-IDLE;SCX-1110/XRX,POM,0.5,31,-,WHT,
GEAR-TIMING;SCX-6320F,POM(M90-44),M0.5,Z
PMO-HOLDER BELT;SCX-1110/XRX,-,POM,WHT,RING-E;ID4,OD9,T0.6,PASS,STSC
CBF HARNESS-PLATEN;SCX-4920N,CBF,UL1061,
DNA : DELIVERY
not AVAILABLE
Location
B2030
L4074
P0013
M2043
G0412
G0434
R0004
SNA
SNA
SNA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
8.6 Middle Cover Assembly Exploded view
8.6-0
8.6-1
8.6-2
8.6-3
8.6-4
8.6-5
8.6-6
JC96-03247A
JC63-00502A
JC63-00388B
JC72-00973A
JC61-00902A
JC39-00350B
JC92-01636A
ELA HOU-COVER MIDDLE;SCX-4720F,-,ROCKY2,
COVER-M-MIDDLE_SEC;SCX-4720F,HIPS,-,434.
COVER-M-REAR UP_SEC;SCX-4720F,ABS,-,39.2
PMO-STACKER_RX;ML-1710,HIPS,SOFT WHITE,BUSH-M-F/DOWN R2;SCX-4920N,POM,-,-,-,BLK
CBF HARNESS-OPE;SCX-4720FN,CBF,UL1061,6P
PBA SUB-USB HOST;SCX-4720F,SEC,-,USB HOS
Z2062
Z2199
Z2222
Z5090
K2878
L0439
SA
SA
SA
SA
SA
SA
SA
8.7 Frame Ass’y Exploded view
8.7-0
8.7-1
8.7-2
8.7-3
8.7-4
8.7-5
8.7-6
8.7-7
8.7-8
8.7-9
8.7-10
8.7-11
8.7-12
8.7-13
8.7-14
8.7-15
8.7-16
8.7-17
8.7-18
8.7-19
8.7-20
8.7-21
8.7-22
8.7-23
8.7-24
8.7-25
8.7-26
8.7-27
8.7-27-1
8.7-27-2
8.7-27-3
8.7-28
JC96-03186A
JC61-00906A
JC61-00607A
JC61-00604B
JC61-00594A
JC72-00143A
JC61-00835A
JC61-00836A
JC63-00397A
JC75-00049A
JC61-00903A
JC61-00904A
JC61-00911A
JC72-00983A
JC72-00974A
JC72-00985A
JC61-70932A
JC63-00401A
JC72-00984A
JC72-01323A
JC72-00975A
JC72-01324A
JC63-00395A
JC63-00403A
JC66-00526A
JC72-00382B
JC66-00398A
JC97-01926A
JC72-01231A
JC61-00909A
JC61-00910A
JC70-00307A
ELA HOU-FRAME_110V;SCX-4720F,SEC,ROCKY2,
FRAME-M-BASE R2;SCX-4920N,PC+ABS(NH-1000
GUIDE-P-TR;ML-1710,SECC,0.5,239.1,76.4,PLATE-E_SAW;SF-755P,SUS304-CSP 1/2H,0.1,
GUIDE-M-TR RIB;ML-1710,PC+ABS,-,-,-,BLK,
PMO-GEAR_EXIT_DRV16;SF-5100,POM(DE8903),
FOOT-BACK;ML-1750,NBR,D13.6,-,10.5,-,FOOT-FRONT;ML-1750,NBR,D7,-,11.5,-,GROUND-P-GUDIE TR R2;SCX-4920N,SUS301 1/
MEC-TERMINAL;SF-5100,SAMSUNG,-,-,-,-,-,PLATE-P-TERMINAL CON R2;SCX-4920N,SUS304
PLATE-P-TERMINAL CR R2;SCX-4920N,SUS301HOUSING-M-TERMINAL R2;SCX-4920N,ABS(NH-1
PMO-LOCKER CST;ML-1710,POM(DELIN 900P),W
PMO-ACTUATOR CVR OPEN;ML-1710,PC V0(NH10
PMO-PLATE GUIDE DEVE_R;ML-1710,POM(M90-4
SPRING ETC-GUIDE DEVE;ML-5000A,-,D4.3,-,
GROUND-P-PUSH BUSHING;SCX-4920N,C5210P,0
PMO-PLATE GUIDE DEVE_L;ML-1710,POM(M90-4
PMO-ACT FEED R2;SCX-4920N,PC(NH-1023P),B
PMO-ACTUATOR EMPTY;ML-1710,PC(NH-1023P),
PMO-ACT MANUAL R2;SCX-4920N,PC(NH-1023P)
GROUND-P-EARTH TR R2;SCX-4920N,SUS301 1/
GROUND-P-TERMINAL TR;SCX-4920N,STS304 WP
ROLLER-FEED ROLLER 1;ML-1510,SUM24L+NI+E
PMO-BUSHING FEED;ML-1710,POM(DERLIN 8903
SHAFT-FEED;ML-1710,POM(M90-44),-,-,NTR,MEA UNIT-PICK UP;SCX-4920N,DELL,-,PICK U
SPONGE-ROLLER PICK_UP;ML-1510,EPDM+IR,-,
HOUSING-M-PICK UP_R2;SCX-4920N,PC+ABS,-,
HOUSING-M-PICK UP2_R2;SCX-4920N,PC+ABS,IPR-P-EARTH TRANSFER;ML-1710,SECC,-,1.0T
ͥ
B0081
G2089
P5152
G2079
F1010
F1011
K3739
K3385
P8153
H6040
L6030
O1073
G2286
K3234
G2285
F6156
K3816
K4129
K3232
G2130
F6201
P0034
F6210
P2092
P2164
M2077
M2078
K3367
SA
SA
SA
SA
SA
SNA
SA
SA
SNA
SA
SNA
SNA
SA
SA
SA
SA
SA
SNA
SA
SNA
SA
SA
SNA
SA
SA
SA
SA
SA
SA
SA
SA
SA
Draw#
8.7-29
8.7-30
8.7-31
8.7-32
8.7-33
8.7-34
8.7-36
8.7-37
8.7-38
8.7-39
8.7-40
8.7-41
8.7-42
8.7-43
8.7-44
8.7-45
8.7-45-1
8.7-45-2
8.7-45-3
8.7-46
8.7-46-1
8.7-46-2
8.7-47
8.7-47-1
8.7-47-2
8.7-47-3
8.7-47-4
8.7-47-5
8.7-49
8.7-50
8.7-51
8.7-52
8.7-53
8.7-54
8.7-55
8.7-56
8.7-58
8.7-59
8.7-61
8.7-62
8.7-63
8.7-64
8.7-65
8.7-65-1
8.7-65-2
8.7-65-3
8.7-65-4
8.7-66
8.7-68
8.7-69
8.7-70
8.7-71
8.7-72
8.7-73
8.7-74
8.7-75
8.7-76
8.7-77
8.7-78
Part Code
JC61-00907A
JC67-00027A
JC72-00102A
JC61-00047A
JC66-00598A
JC61-00588A
JC66-00527A
JC61-00585A
JC61-70958A
JC63-00398A
6107-001170
JC66-00377A
JC63-00394A
JC33-00014A
JC33-00010A
JC97-01929A
JC66-00705A
JC66-00704A
6107-001167
JC97-01925A
JC61-00913A
JC66-00690A
JC97-01788A
JC66-00393A
JC72-00978A
6107-001171
JC72-00981A
JC66-00398A
JC61-00914A
JC66-00394A
JC66-00396A
6107-001164
6107-001165
JC70-00340A
JC63-00458A
JC92-01620A
JC61-00908A
JC61-00912A
JC61-00829A
JC66-00038A
JC66-00378A
JC73-40915A
JC97-01034A
JC72-41006A
JC72-41007A
JC72-41008A
JC61-70911A
JC61-00917A
JC92-01605A
JC39-00356A
JC92-01604A
JC63-00402A
JC68-00317A
JC61-00586A
JC66-00399A
JC61-00915A
JC72-00982A
JC61-00587A
JC66-00720A
Description
HOLDER-M-PTL R2;SCX-4920N,PC(NH-1023P),1
LENS-PTL;ML-1710,PMMA,NTR,-,-,-,PMO-BUSHING_TR(L);SF-5100,POM (CH-15),BL
SPRING ETC-TR L HAWK;ML-6060A,SWP-B,-,-,
ROLLER-FEED;ML-1710,SUM24L+NI+EPDN,5/12.
BUSH-M-TR L;ML-1710,POM(M90-44),-,-,-,BL
SHAFT-FEED IDLE;ML-1510,SUM24L+NI,223,8,
BUSH-M-FEED IDLE;ML-1710,POM(CF620-GF20%
SPRING ETC-TR;ML-5000A,SUS304 WPB,PI0.55
GROUND-P-DRIVE2 R2;SCX-4920N,SUS301 1/2H
SPRING-TS;SWP-B,-,PI0.9,D6.0,-,-,-,ID5.2
CAM-M-PICK_UP;ML-1710,POM(DELIN 8903),-,
GROUND-P-DRIVE R2;SCX-4920N,SUS301 1/2H,
SOLENOID-FEED ROCKY2;-,SCX-4920,-,-,-,-,
SOLENOID-HB (MANUAL);-,ML-1510,DC24V,-,MEA UNIT-GEAR PICK UP;SCX-4920N,DELL,-,G
GEAR-PICK UP B_R2;SCX-4920N,POM(M90-44),
GEAR-PICK UP A_R2;SCX-4920N,POM(DELRIN 5
SPRING-CS;SUS304-WPB,-,PI0.25,D3.25,L9.6
MEA UNIT-BRACKET FEED;SCX-4920N,DELL,-,B
BRACKET-P-FEED R2;SCX-4920N,SECC,1.0,100
GEAR-35 IDLE;SF-755P,POM(M90-44),0.8,35,
MEA UNIT-CLUTCH;ML-1710,SAMSUNG,-,-,-,-,
GEAR-FEED 1;ML-1710,POM(DELIN 8903),-,-,
PMO-COLLAR_SPRING;ML-1710,POM(M90-44),NT
SPRING-TS;SWRS82A,-,0.75X0.5,D14.2,-,-,PMO-HUB CLUTCH;ML-1710,POM(M90-44),NTR,SHAFT-FEED;ML-1710,POM(M90-44),-,-,NTR,PLATE-P-PUSH BUSHING;SCX-4920N,SECC,0.8,
GEAR-FEED 2;ML-1710,POM(M90-44),-,-,-,NT
GEAR-IDLE 23;ML-1710,POM(M90-44),0.8,23,
SPRING-TS;SUS304-WPB,-,PI0.15,D3.95,L12,
SPRING-TS;SUS304-WPB,-,PI0.2,D4,-,-,-,ID
IPR-P-TERMINAL DEVE KEY;SCX-4216F,SUS304
GROUND-P-TERMINAL DEVE;SCX-4920N,STS304
PBA SUB-PTL;SCX-4920N,DELL,-,PTL,-,-,-,8
HOLDER-M-TERMINAL R2;SCX-4920N,PC+ABS(NH
HOLDER-M-ACT MANUAL R2;SCX-4920N,ABS,-,3
HOLDER-BEARING EXIT F/DOWN;SCX-4216F,POM
GEAR-EXIT F/DOWN;ML-4500,POM,WHT,-,ROLLER-EXIT F/DOWN;ML-1710,PC(NH-1023),9
RMO-RUBBER EXIT;SF-5800P,EPDM,11.6 PI,60
MEA RACK-EXIT ROLLER;ML-1605,SUMSUNG,KOR
PMO-HOLDER EXIT ROLL;ML-165,PC,BLK,HB,PMO-ROLLER FD F;ML-165,POM,BLACK,-,-,-,PMO-ROLLER FD R;ML-165,POM,BLACK,-,-,-,SPRING ETC-EXIT ROLL FD;ML-165,SUS304 WP
GUIDE-M-SUB FRONT;SCX-4920N,HIPS,-,54.2,
PBA SUB-CRUM;SCX-4920N,SEC,KOREA,TONER,C
CBF HARNESS-CRUM2;SCX-4920N,CBF,UL1061,4
PBA SUB-EXIT SENSOR;SCX-4920N,SEC,KOREA,
GROUND-P-SHIELD R2;SCX-4920N,C5210P,0.2,
LABEL(R)-HOT CAUTION,KME;ML-7050,TETRON,
BUSH-M-PICK_UP L;ML-1710,POM(DELIN 8903)
SHAFT-P-PICK_UP;ML-1710,SECC,-,-,-,-,0.8
STOPPER-M-PICK UP_R2;SCX-4920N,POM(DELIN
PMO-IDLE PICK_UP;ML-1710,POM(M90-44),NTR
BUSH-M-PICK_UP R;ML-1710,POM(M90-44),-,SHAFT-P-CORE;ML-1750,SECC 1.2T,203,-,-,-
DNA : DELIVERY
not AVAILABLE
Location
SNA
H4041
K3433
K3856
S0033
F6200
K2886
F6209
F6043
P2039
P2160
K3752
P2131
P2067
P2158
SA
SA
SA
SA
SA
SA
SA
SA
SA
SNA
SA
SA
SNA
SA
SA
SA
SA
SA
SA
SA
SA
SNA
SA
SA
SA
SA
SNA
SA
SNA
SA
SA
SA
SNA
SNA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SNA
SA
SA
SA
SA
SNA
SA
SA
SA
SA
SA
SA
F4031
Z2194
SA
SA
P2042
P2162
S8015
P2009
G0360
D4089
F6040
F6041
G0147
C9040
F6071
Z4125
F6210
K3234
F6072
G0256
T2116
M0248
H4037
H4020
H4009
E4039
E4159
E4060
E4126
P0048
P0049
S0021
H5017
M0330
K3235
8.8 Fuser Ass’y Exploded view
8.8-0
8.8-1
JC96-03210A ELA HOU-FUSER LV R2;SCX-4720F,SEC,-,FUSE
JC63-00363A COVER-M-FUSER R2;SCX-4920N,PET+GF30%,78.
ͦ
Draw#
8.8-2
8.8-3
8.8-4
8.8-5
8.8-6
8.8-7
8.8-8
8.8-9
8.8-10
8.8-11
8.8-12
8.8-13
8.8-14
8.8-15
8.8-16
8.8-17
8.8-18
8.8-19
8.8-20
8.8-21
8.8-22
8.8-23
8.8-24
8.8-25
8.8-26
8.8-27
8.8-28
8.8-29
8.8-30
8.8-31
8.8-32
8.8-33
8.8-34
8.8-35
8.8-36
8.8-37
8.8-38
Part Code
JC61-00886A
JC61-00064A
JC72-40361A
JC61-70976A
JC47-00005A
JC72-00143A
JC66-00396A
6044-000125
JC66-00397A
JC66-00729B
JC70-00473A
1404-001337
JC70-00472A
JC39-00353A
JC61-00887A
JC68-30928D
JC73-00017A
JC66-00380A
JC66-00600B
JC66-10901A
6107-001168
JC72-00382A
JC61-00581A
JC72-01319A
JC61-00890A
JC61-00889A
6107-001165
6021-000222
JC61-00888A
JC61-00605A
JC66-00695A
4713-001182
JC68-00408A
6003-000196
6006-001193
6003-000269
JC75-00095A
Description
HOLDER-M-PLATE CLAW R2;SCX-4920N,PPS+GF4
SPRING ETC-CLAW;ML-5200A,SUS 304 WPB,¥Õ0
PMO-ROLLER_EXIT;SCF(XR),POM,NATURAL,-,M9
SPRING ETC-FUSER EXIT;ML-7000,SUS304-WPB
THERMOSTAT-150;ML-1510,-,125/250V,15/7.5
PMO-GEAR_EXIT_DRV16;SF-5100,POM(DE8903),
GEAR-IDLE 23;ML-1710,POM(M90-44),0.8,23,
RING-E;ID4,OD9,T0.6,PASS,STSC
GEAR-RDCN 25/15;ML-1710,POM(M90-44),-,25
ROLLER-HEAT_210;SCX-4520,AL + 210PFA COA
ELECTRODE-P-LFET R2;SCX-4920,-,-,-,-,THERMISTOR-NTC;7KOHM,-,3370K,0.3MW/C,-,ELECTRODE-P-RIGHT R2;SCX-4920,-,-,-,-,CBF HARNESS-FUSER 110V;SCX-4920N,CBF,UL3
BUSH-M-HR R_R2;SCX-4920N,PPS(RBA313N),25
LABEL(P)-CAUTION, HOT_FUSER;ML-1210,PET,
RMO-RUBBER_EXIT;SF-5100,EPDM,14.4*9.8,50
ROLLER-M-EXIT F/UP;ML-1710,PC(GE EXL-911
ROLLER-PRESSURE_CHINA;ML-1710/XIL,SPONGE
BEARING-PRESSURE/R;ML-165,PPS(RBA313N),SPRING-CS;PW-2,-,PI0.95,D5.95,L16,-,-,ID
PMO-BUSHING TX;ML-6060A,POM M9044,BLK,-,
HOLDER-ACTUATOR;ML-1710,PBT GP2150+GF 15
PMO-ACTUATOR EXIT R2;SCX-4920N,PC+GF20%,
FRAME-P-FUSER R2;SCX-4920,SECC,-,-,-,1.2
GUIDE-M-INPUT R2;SCX-4920N,PET+GF30%,2.5
SPRING-TS;SUS304-WPB,-,PI0.2,D4,-,-,-,ID
NUT-HEXAGON;2C,M3,ZPC(YEL),SM20C,BUSH-M-HR L_R2;SCX-4920N,PPS(RBA313N),25
PLATE-P-CLAW;ML-1710,SUS304-CSP,0.1,-,-,
GEAR-FUSER R2;SCX-4920N,PPS(OFL4036),0.8
LAMP-HALOGEN;115V,-,600W,-,-,-,6X284MM
LABEL(R)-LV FUSER;COMMON,PVC,-,110V,-,,,
SCREW-MACHINE;WSP,PH,+,M3,10,ZPC(YEL),SW
SCREW-TAPTITE;BH,+,-,S,M3,L6,ZPC(YEL),SW
MEC-BRUSH ANTISTATIC;ML-6060A,SEC,NTR
DNA : DELIVERY
not AVAILABLE
Location
SNA
H4031
B2031
R0015
S0021
K4279
SA
SA
SNA
SNA
SA
SNA
SA
SA
SA
SA
SNA
SA
SNA
SA
SA
SNA
SA
SA
SA
SA
SA
SNA
SNA
SA
SA
SNA
SNA
SNA
SA
SNA
SA
SA
SNA
SA
SNA
SA
SA
G0256
R0004
G0386
H2010
H1085
K2880
K4215
E0041
P6016
P6004
D4085
E4093
F2122
K2879
H4032
D4037
K2297
L0006
M0022
8.9 MP Assembly Exploded view
8.9-0
8.9-1
8.9-2
8.9-3
8.9-4
8.9-5
8.9-5-1
8.9-5-2
8.9-5-3
8.9-6
8.9-7
8.9-9
8.9-10
8.9-11
8.9-12
8.9-13
8.9-14
8.9-15
8.9-16
8.9-17
8.9-18
8.9-19
8.9-20
8.9-21
JC96-03132B
JC61-00923A
JC33-00015B
JC39-00365B
JC61-00587A
JC97-02034A
JC61-00909A
JC61-00925A
JC73-00194A
JC61-00915A
JC61-00924A
JC61-00926A
JC61-00927A
JC61-00932A
JC66-00396A
JC66-00399A
JC66-00529A
JC66-00710A
JC66-00709A
JC66-00711A
JC72-00761A
JC72-00982A
JC72-01338A
JC73-00140A
ELA UNIT-MP_R2;SCX-4720F,SEC,-,MP,-,-,FRAME-M-MP;ML-2250,ABS,-,-,-,2.5,85.5,31
SOLENOID-MP_R2;-,SCX-4720F,DC24V,-,-,-,CBF HARNESS-MPF SEN;SCX-4720F,CBF,UL1061
BUSH-M-PICK_UP R;ML-1710,POM(M90-44),-,MEA-PICK UP_MP;ML-2250,SEC,-,PICK UP-MP
HOUSING-M-PICK UP_R2;SCX-4920N,PC+ABS,-,
HOUSING-M_PICK UP_MP;ML-2250,PC+ABS,-,20
RUBBER-PICK UP MP;SCX-4720F,EPDM + IR,-,
STOPPER-M-PICK UP_R2;SCX-4920N,POM(DELIN
HOLDER-M-PAD_MP;ML-2250,PC+ABS,-,48,24.2
HOLDER-M-SENSOR_MP;ML-2250,ABS,-,22.3,36
PLATE-P-KNOCK UP_MP;ML-2250,SECC,1.0,252
BRACKET-P-PICKUP_MP;ML-2250,SECC,1.2,57.
GEAR-IDLE 23;ML-1710,POM(M90-44),0.8,23,
SHAFT-P-PICK_UP;ML-1710,SECC,-,-,-,-,0.8
ROLLER-M-IDLE FEED;ML-1510,POM(DELRIN890
GEAR-M-PICK UP_MP;ML-2250,POM,0.8,33,-,GEAR-M-HOLDER_MP;ML-2250,POM,0.8,33,-,-,
CAM-M-PICK UP MP;ML-2250,POM,-,26.1*15.9
PMO-ROLLER CAM.MP;SCX-5100,POM,WHITE,-,PMO-IDLE PICK_UP;ML-1710,POM(M90-44),NTR
PMO-M-ACT EMPTY MP;ML-2250,PC,BLK,H31.4,
RPR-FRICTION PAD;ML-1510,NBB,1T 8.9*47,5
ͧ
K3155
F2243
S8014
P2067
M2077
P2148
K3752
H4029
H4108
P2122
G0256
P2160
F6203
P2110
H4073
P2041
K4061
P2131
K3119
P0034
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SNA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
Draw#
8.9-23
8.9-24
8.9-25
8.9-26
8.9-27
8.9-28
8.9-29
8.9-30
8.9-31
Part Code
JC61-70911A
JC73-00141A
6107-001237
JC63-00545A
JC66-00720A
JC63-00448A
6107-001167
6107-001047
0604-001095
Description
SPRING ETC-EXIT ROLL FD;ML-165,SUS304 WP
RPR-PAD CASSETTE;ML-1510,URETHANE SPONGE
SPRING-ES;SUS304-WPB,-,P0.5,D4.5,L42,-,SHEET-GUIDE PAPER H2;ML-2250,PET,0.188T,
SHAFT-P-CORE;ML-1750,SECC 1.2T,203,-,-,SHEET-GUIDE MP;ML-2250,PET,0.125,200,25,
SPRING-CS;SUS304-WPB,-,PI0.25,D3.25,L9.6
SPRING-ES;PI0.45,D2.75,L24.2,-,SUS304
PHOTO-INTERRUPTER;TR,90%,150mW,DIP-4,BK
DNA : DELIVERY
not AVAILABLE
Location
SNA
S0021
R0020
SA
SA
SNA
SNA
SA
SNA
SA
SA
SA
P2158
D4089
P0013
8.10 Cassette Ass’y Exploded view
8.10-0
8.10-1
8.10-2
8.10-3
8.10-4
8.10-5
8.10-6
8.10-6-1
8.10-6-2
8.10-6-3
8.10-6-4
8.10-7
8.10-8
8.10-10
8.10-11
8.10-12
8.10-13
8.10-14
8.10-15
8.10-16
8.10-17
JC97-02020A
JC61-00876B
JC61-00918B
JC72-00971A
JC61-00603A
6107-001166
JC97-01931A
JC61-00580A
JC63-00407A
JC73-00140A
JC70-00314A
JC61-70911A
JC63-00490A
JC72-00972A
JG61-70531A
JC70-00300A
JC70-00301A
JG66-40003A
JC73-00141A
JC66-00719A
JC64-00143A
MEA-CASSETTE;SCX-4720F,SEC,ROCKY2,CASSET
FRAME-M_CASSETTE HR;ML-1740,HIPS,HR-1360
GUIDE-M-EXTENSION L2;ML-2250,HIPS,-,184.
PMO-EXTENSION SMALL;ML-1710,ABS(HF-0660I
PLATE-P-KNOCK_UP;ML-1710,SECC,1,250.7,16
SPRING-CS;SUS304-WPB,-,PI0.65,D12.65,L59
MEA UNIT-HOLDER PAD;SCX-4920N,DELL,-,HOL
HOLDER-M-PAD;ML-1710,PC+ABS(NH-1023P),-,
SHEET-HOLDER PAD R2;SCX-4920N,PC,0.125T,
RPR-FRICTION PAD;ML-1510,NBB,1T 8.9*47,5
IPR-PLATE PAD;ML-1710,SUS304-CSP,-,0.1,SPRING ETC-EXIT ROLL FD;ML-165,SUS304 WP
COVER-M-SUB CST_SEC;SCX-4720F,HIPS,-,417
PMO-PLATE_LOCKER;ML-1710,POM(M90-44),WHT
SPRING ETC-LOCKER,PLATE;SF6000,STS304WPB
ADJUST-M-CASSETTE_L;ML-1400,ABS,-,-,-,VI
ADJUST-M-CASSETTE_R;ML-1400,ABS,-,-,-,VI
RPR-PAD CASSETTE;ML-1510,URETHANE SPONGE
CAM-M-KNOCK UP;ML-1750,POM(KOLON K700),INDICATOR-M-CST PAPER;ML-2250,HIPS(HR-13
C4045
E5013
E5014
P0014
P0034
P0034
P0009
S0021
L6051
S0025
K2014
K2015
G0035
R0020
S4102
SA
SA
SA
SA
SNA
SA
SA
SA
SNA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SNA
SNA
8.11 SCF Assembly(Option)
8.11-1
JC63-00505A
8.11-2
JC63-00500A
8.11-3
JC63-00499A
8.11-4
JC63-00503A
8.11-6
JC61-00909A
8.11-7
JC61-00910A
8.11-8
JC72-01231A
8.11-9
JC66-00720A
8.11-10
JC72-00382B
8.11-11
JC61-00586A
8.11-12
JC61-00587A
8.11-13
JC66-00399A
8.11-14
JC72-00982A
8.11-15
JC66-00598A
8.11-21
JC66-00377A
8.11-22
JC66-00527A
8.11-23
JC66-00394A
8.11-25
JC41-00247A
8.11-31
JC72-00975A
8.11-33
JC33-00010A
8.11-34
JC72-00983A
8.11-35
JC61-00835A
8.11-36
JC61-00836A
8.11-42
JC97-02020A
Replacement JC69-00896A
Replacement 3903-000085
Replacement JF39-50094B
JC72-00067B
0402-000129
COVER-M-FRONT_SEC;SCX-4720F,HIPS,-,431,1
COVER-M-SIDE L_SEC;SCX-4720F,HIPS,-,398.
COVER-M-SIDE R_SEC;SCX-4720F,HIPS,-,398.
COVER-M-REAR_SEC;SCX-4720F,HIPS,-,403.0,
HOUSING-M-PICK UP_R2;SCX-4920,PC,-,20,30
HOUSING-M-PICK UP2_R2;SCX-4920,PC,-,53,2
SPONGE-ROLLER PICK_UP;ML-1510,URETHAN FO
SHAFT-P-CORE;ML-1750,SECC 1.6T,220,-,-,PMO-BUSHING FEED;ML-1710,DELRIN8903,WHIT
BUSH-M-PICK_UP L
BUSH-M-PICK_UP R;ML-1400,POM(M90-44),-,SHAFT-P-PICK_UP;ML-1400,SECC,-,-,-,-,0.8
PMO-IDLE PICK_UP;ML-1400,POM(M90-44),NTR
ROLLER-FEED ;ML-1710,SUM24L+EPDN,3/14.5,
CAM-M-PICK_UP;ML-1400,POM(M90-44),-,-,NT
SHAFT-FEED IDLE;ML-1510,SUM24L,225,8,-,GEAR-FEED 2;ML-1400,POM(M90-44),-,-,-,NT
PCB-SENSOR B'D;SCX-4920N,FR-1,1,-,1.6T,3
PMO-ACTUATOR EMPTY;ML-1400,ABS,BLK,-,-,H
SOLENOID-HB (MANUAL);-,ML-1510,DC24V,-,PMO-LOCKER CST;ML-1400,POM,BLK,-,-,-,-,FOOT-BACK;ML-1750,NBR,D13.6,-,10.5,-,FOOT-FRONT;ML-1750,NBR,D7,-,12,-,MEA-CASSETTE;SCX-4720F,SEC,ROCKY2,CASSET
BOX(P)-MAIN_US;SCX-4720FN/XAA,DC3,A-1,53
CBF-POWER CORD;DT,US,BP3/YES,I(IEC C13/C
CBF LINE CORD;MINI FAX,-,-,IVR,PPR-DUMMY SHEET(AT);CF-5800,ABS-IV16,IVO
DIODE-RECTIFIER;1N4003,200V,1A,DO-41,TP
ͨ
D0014
Z2166
Z2167
Z2220
P2064
P2065
P2164
F6161
P2039
P2067
P2160
P2131
F6200
P2042
F6209
F6072
K3816
S8014
L6030
F1010
F1011
C4045
K2903
D2120
SA
SNA
SA
SA
SA
SA
SA
SNA
SA
SA
SA
SA
SNA
SA
SA
SA
SA
SNA
SA
SA
SA
SA
SA
SA
SNA
SA
SA
SA
SA
Draw#
Part Code
0402-000132
0403-000537
0501-000398
0502-000245
1401-001069
2001-000015
2001-000935
2003-000507
2005-000168
2201-000161
2305-000385
2801-003960
3501-000203
3708-001637
3711-000015
3711-003942
3711-004349
3722-002303
3722-002345
6001-000568
6045-001009
6501-000004
6502-001093
JB27-00004A
JC39-00001A
JC39-30002A
JC61-00937A
JC68-01584A
JC97-01927A
JC97-01928A
JC97-01930A
0401-001090
0404-000112
0407-000122
0501-000150
0501-000479
0502-001258
0504-000111
0505-001350
0601-001619
0801-000794
0801-002143
0801-002591
0904-001865
0904-001989
1001-000170
1003-001122
1003-001535
1006-001224
1105-001379
1106-001453
1107-001549
1201-000105
1202-000164
1203-002220
1203-003700
1205-002339
1205-002478
1205-002654
1404-001065
2007-000052
2007-000071
2007-000082
Description
DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP
DIODE-ZENER;1N4749A,5%,1000MW,DO-41,TP
TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T
TR-POWER;KSB1151-Y,PNP,1.3W,TO-126,-,16
THYRISTOR-SIDAC;P3100EB,275V,0.15A,250A,
R-CARBON(S);0.5OHM,5%,1/2W,AA,TP,2.4X6.4
R-CARBON;68OHM,5%,1/4W,AA,TP,2.4X6.4MM
R-METAL OXIDE(S);15Kohm,5%,1W,AA,TP,3.3x
R-WIRE WOUND,NON;0.22ohm,5%,2W,AA,BK,4x1
C-CERAMIC,DISC;10NF,+80-20%,500V,Y5V,TP,
C-FILM,LEAD-PEF;470nF,10%,250V,BK,18x6x1
CRYSTAL-UNIT;28.224MHz,50ppm,28-AAA,18pF
RELAY-MINIATURE;5V,200MW,1000MA,1FORMC,6
CONNECTOR-FPC/FFC/PIC;24P,1MM,STRAIGHT,S
HEADER-BOARD TO CABLE;BOX,2P,1R,2.5MM,ST
HEADER-BOARD TO CABLE;BOX,2P,1R,2mm,STRA
HEADER-BOARD TO CABLE;BOX,3P,1R,2MM,STRA
JACK-USB;4P/1C,AU30U,BLK,ANGLE,B TYPE
JACK-MODULAR;6P/4C,INVERTED,N,ANGLE,N,GR
SCREW-MACHINE;PH,+,M3,L8,NI PLT,SWRCH18A
SPACER-ROUND;ID6,OD10,T1.0,NTR,NYLON66,L
CABLE TIE;DA-80,T1,W2.5,L80,NTR,NYLON66
CABLE CLAMP;DAWS-3NE,ID11*L34.8,-,NYLON6
COIL CHOKE-DIP;DR 8X11(470UH),MJC-1450,4
CBF INTERFACE-USB;ML-6100,4,UL2725,1800
CBF INTERFACE;-,-,-,1810,-,GRY,-,-,-,GUIDE-M-KNOCK UP;ML-1750,POM,-,77.8,20.8
LABEL(P)-BLANK 90*25;CLP-510,SEE,ART 100
MEA UNIT-ACT FEED;SCX-4920N,DELL,-,ACT F
MEA UNIT-ACT MANUAL;SCX-4920N,DELL,-,ACT
MEA UNIT-ROLLER EXIT;SCX-4920N,DELL,-,RO
DIODE-SWITCHING;1SS355,80V,100MA,SOD-323
DIODE-SCHOTTKY;RB420D,40V,100MA,SOT-23,T
DIODE-ARRAY;KDS226,80V,300mA,C2-3,SOT-23
TR-SMALL SIGNAL;2SA1037,PNP,200mW,SOT-23
TR-SMALL SIGNAL;KST42,NPN,350mW,SOT-23,T
TR-POWER;FJT44,NPN,-,SOT-223,TP,40-200
TR-DIGITAL;DTC114YK,NPN,200MW,10K/47K,SO
FET-SILICON;NDT2955,P,-60V,-2.5V,0.3OHM,
LED;CBI,RED/GRN,3MM,635/568NM,6.35X7X6MM
IC-CMOS LOGIC;7S08,AND GATE,SOT-25,5,63M
IC-CMOS LOGIC;7S32,OR GATE,SOT-23,5P,63M
IC-CMOS LOGIC;74LVX273,D FLIP-FLOP,TSSOP
IC-USC;OTG242LP,16BIT,LQFP,64P,10.0X10.0
IC-USC;ISP1582BS,-,HVQFN56,56P,8X8X0.85M
IC-ANALOG SWITCH;MC14051BD,SPDT CMOS,SOP
IC-MOTOR DRIVER;TEA3718SFP,SOP,20P,300MI
IC-MOTOR DRIVER;A3977SLP,TSSOP,28P,9.6X4
IC-LINE TRANSCEIVER;74LVX161284,TSSOP,48
IC-DRAM;K4S561632,4X4MX16BIT,TSOP(II),54
IC-SRAM;K6R1016V1D,64KX16BIT,TSOP(II),44
IC-FLASH MEMORY;K9F5616U0C,16MX16BIT,TSO
IC-AUDIO AMP;34119,SOP,8P,150MIL,SINGLE,
IC-VOLTAGE COMP.;393,SOP,8P,150MIL,DUAL,
IC-POSI.ADJUST REG.;LD1117,DPAK,3P,240MI
IC-POSI.ADJUST REG.;LD1117ADT-R,DPAK,3P,
IC-CLOCK GENERATOR;CY25811SC,SOIC,8P,150
IC-DAA;CX20493-21/FAX,QFN,28P,5X5MM,PLAS
IC-MODEM;CX86710-12,TQFP,64P,7X7MM,PLAST
THERMISTOR-PTC;0.11OHM,-,-,13.2VAC,40A,1
R-CHIP;10Kohm,1%,1/10W,TP,1608
R-CHIP;22ohm,5%,1/10W,TP,1608
R-CHIP;3.3Kohm,5%,1/10W,TP,1608
ͩ
DNA : DELIVERY
not AVAILABLE
Location
K2756
C0002
K2897
P5146
F6162
F6163
SNA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
Draw#
Part Code
2007-000083
2007-000084
2007-000086
2007-000091
2007-000092
2007-000093
2007-000096
2007-000097
2007-000098
2007-000105
2007-000106
2007-000107
2007-000109
2007-000116
2007-000119
2007-000123
2007-000131
2007-000134
2007-000136
2007-000293
2007-000303
2007-000481
2007-000660
2007-001002
2007-001056
2007-001134
2007-001139
2007-002760
2007-002901
2007-007521
2007-008473
2007-008510
2011-000002
2011-000651
2203-000206
2203-000257
2203-000384
2203-000426
2203-000491
2203-000681
2203-000783
2203-000975
2203-001222
2203-001598
2203-001607
2203-001683
2203-002392
2203-002398
2203-005221
2203-005757
2402-000008
2402-000117
2402-000173
2402-001049
2602-000061
2602-000062
3711-005861
3722-001319
6003-000282
JC13-00023A
JC13-00031B
JC39-00045A
JC39-00184A
Description
R-CHIP;4.7Kohm,5%,1/10W,TP,1608
R-CHIP;5.6Kohm,5%,1/10W,TP,1608
R-CHIP;200Kohm,5%,1/10W,TP,1608
R-CHIP;220Kohm,5%,1/10W,TP,1608
R-CHIP;470Kohm,5%,1/10W,TP,1608
R-CHIP;1Mohm,5%,1/10W,TP,1608
R-CHIP;120ohm,5%,1/10W,TP,1608
R-CHIP;560ohm,5%,1/10W,TP,1608
R-CHIP;1.5Kohm,5%,1/10W,TP,1608
R-CHIP;300Kohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/4W,TP,3216
R-CHIP;27ohm,5%,1/4W,TP,3216
R-CHIP;510ohm,5%,1/10W,TP,1608
R-CHIP;6.2Kohm,5%,1/10W,TP,1608
R-CHIP;68ohm,5%,1/10W,TP,1608
R-CHIP;7.5Kohm,1%,1/10W,TP,1608
R-CHIP;6.8Mohm,5%,1/4W,TP,3216
R-CHIP;12.1Kohm,1%,1/10W,TP,1608
R-CHIP;14.7Kohm,1%,1/10W,TP,1608
R-CHIP;237KOHM,1%,1/4W,DA,TP,3216
R-NET;22OHM,5%,1/16W,L,CHIP,8P,TP,3216
R-NET;10ohm,5%,1/16W,L,CHIP,8P,TP,3216
C-CER,CHIP;100nF,10%,50V,X7R,2012
C-CER,CHIP;10nF,10%,50V,X7R,1608
C-CER,CHIP;0.015nF,5%,50V,C0G,1608
C-CER,CHIP;0.018nF,5%,50V,C0G,1608
C-CER,CHIP;2.2nF,10%,50V,X7R,TP,1608,C-CER,CHIP;0.027nF,5%,50V,C0G,1608
C-CER,CHIP;0.33nF,5%,50V,C0G,1608
C-CER,CHIP;47nF,10%,25V,X7R,TP,1608,C-CER,CHIP;0.82NF,10%,50V,X7R,TP,1608
C-CER,CHIP;2200nF,+80-20%,16V,Y5V,TP,201
C-CER,CHIP;0.22nF,5%,50V,NP0,1608
C-CER,CHIP;0.068nF,5%,50V,NP0,1608
C-CER,CHIP;220nF,+80-20%,50V,Y5V,2012
C-CER,CHIP;33nF,10%,200V,X7R,TP,3216
C-AL,SMD;47uF,20%,16V,GP,TP,6.6x6.6x5.4
C-AL,SMD;4.7uF,20%,35V,GP,TP,4.3x4.3x5.4
TRANS-PULSE;30UH,0.225/0.325OHM,1:1.5,9.
TRANS-PULSE;450UH,0.25/0.25OHM,1:1,12.8X
HEADER-BOARD TO BOARD;BOX,40P,2R,0.8MM,S
JACK-MODULAR;8P/8C,STANDARD,Y,ANGLE,INVE
SCREW-TAPTITE;BH,+,-,B,M3,L8,ZPC(BLK),SW
IC ASIC-A/D CONVERTER;AFE_CIP4,SCX-5315F
IC ASIC-CHORUSM;CHORUSM,SCX-4920N_VE,496
CBF HARNESS-THERMISTOR;SF-5100,#26,UL106
CBF HARNESS-ADF_DET SEN.;SCX-5100,WIRE H
ͪ
DNA : DELIVERY
not AVAILABLE
Location
SNA
H1032
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
Draw#
Part Code
JC39-00372A
JC39-00397A
JC66-00381A
JC66-00384A
JC66-00386A
JC66-00700A
JC72-40232A
JC72-41051A
0401-000005
0407-000101
1103-001183
1103-001279
2007-000070
2007-000113
2007-000287
2007-000475
2007-000539
2007-000965
2011-001094
2203-000041
2203-000440
2203-000815
2404-000284
3722-001051
6002-000175
JB66-00102A
JB66-00104A
JB66-00105A
JB70-00168A
JB72-00817A
JB72-00821A
JB72-00845A
JB75-00299A
JB75-00300A
JC07-00008A
JC39-40511A
JC66-00012A
JC66-00561A
JC66-00728A
JC72-00734A
JC72-00744A
JC97-01935A
0501-000279
0501-000457
0604-001154
0801-001090
1003-001102
2001-001031
2007-000033
2007-000074
2007-000076
2007-000077
2007-000078
2007-000090
2007-000094
2007-000120
2007-000729
2203-000189
2203-000236
2203-000626
2203-000998
2401-001363
2402-000179
Description
CBF HARNESS-PTL;SCX-4920N,CBF,UL1061,2P,
CBF HARNESS-USB HOST;SCX-4720F,CBF,UL 10
GEAR-AGITATOR;ML-1710,POM,0.6,22,-,-,-,GEAR-DEVE ROLLER;ML-1710,CARILON,0.8,-,GEAR-OPC L;ML-1710,PC(LS-1250),0.8,30,-,
ROLLER-SUPPLY R2;SCX-4920N,SUS416+SILICO
PMO-CAP AGITATOR;ML-80,PP,BLK,-,PMO-BUSHING RIGHT;ML-6000,POM(M90-44),BL
DIODE-SWITCHING;1N4148,75V,150mA,DO-35,T
DIODE-ARRAY;DA204K,20V,100mA,C2-3,SOT-23
IC-EEPROM;24C04,512x8,SOP,8P,5x4mm,2.5/5
IC-EEPROM;24C32,4Kx8,SOP,8P,5x4mm,2.5/5.
R-CHIP;0ohm,5%,1/10W,TP,1608
R-CHIP;33ohm,5%,1/10W,TP,1608
R-CHIP;100OHM,1%,1/10W,TP,1608
R-CHIP;200ohm,5%,1/10W,TP,1608
R-CHIP;5.1Kohm,5%,1/10W,TP,1608
R-NET;39OHM,5%,1/16W,L,CHIP,8P,TP
C-CER,CHIP;0.01nF,0.25pF,50V,C0G,1608
C-CER,CHIP;0.033nF,5%,50V,C0G,1608
C-TA,CHIP;10uF,20%,16V,-,TP,3528
JACK-USB;4P/1C,AU,BLK,ANGLE,A TYPE
SCREW-TAPPING;PWH,+,2,M3,L8,ZPC(YEL),SM2
GEAR-PICK UP IDEL 38;SCX-1110F,POM(DELIN
GEAR-ADF IDLE 34;SCX-1110F,POM(DELIN500P
GEAR-PICK UP 26;SCX-1110F,POM(DELIN500P)
ICT-PIN ADF;SCX-1110F,STS303,D2.0,-,-,-,
PMO-ADF CLUTCH;SCX-1110F,POM,WHT,-,-,-,PMO-ADF COLAR;SCX-1110F,POM,NTR,-,-,-,-,
PMO-PICK UP CLUTCH SUB;SCX-1110F,POM(F20
MEC-ADF ROLLER ASSY;SCX-1110F/XRX,XEROX,
MEC-PICK UP ROLLER ASSY;SCX-1110F/XRX,XE
LCD-DISPLAY(XIL);VHX12323ASR,SCX-4521F,1
CBF HARNESS;ML-80,JUMPER,AWG22,52mm,SILV
GEAR-OPC R;SF-5100,POM(M90-44),BLK,M0.6,
SHAFT-ADF PICKUP;SCX-4216F,SUM22L,-,7,NI
ROLLER-ADF FEED;SCX-4920N,POM + EPDM,-,PMO-COVER ADF;SCX-5100,HIPS,WHT,-,-,HB,PMO-SHAFT PICK UP;SCX-5150,-,ABS,BLK,HB,
MEA UNIT-WHITE BAR;SCX-4920N,DELL,-,WHIT
TR-SMALL SIGNAL;KSA1182-Y,PNP,150mW,SOTTR-SMALL SIGNAL;MMBT2222A,NPN,350MW,SOTPHOTO-INTERRUPTER;TR,0.2-1.0MA,80MW,DIP,
IC-CMOS LOGIC;74HC14,SCHMITT INVERTER,SO
IC-MOTOR DRIVER;TEA3718DP,DIP,16P,300MIL
R-CARBON;91KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CHIP;0ohm,5%,1/4W,TP,3216
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;330ohm,5%,1/10W,TP,1608
R-CHIP;470ohm,5%,1/10W,TP,1608
R-CHIP;680ohm,5%,1/10W,TP,1608
R-CHIP;300ohm,5%,1/10W,TP,1608
C-CER,CHIP;100nF,+80-20%,25V,Y5V,1608
C-CER,CHIP;0.1nF,5%,50V,C0G,1608
C-CER,CHIP;0.022nF,5%,50V,C0G,1608
C-CER,CHIP;0.047nF,5%,50V,C0G,1608
C-AL;470uF,20%,16V,GP,TP,10x12.5,5
͢͡
DNA : DELIVERY
not AVAILABLE
Location
G0164
G0561
G0355
I0001
P2150
P0012
SNA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
Draw#
Part Code
3301-001413
3711-003340
6107-001152
JB70-00236A
JB72-00822A
JB72-00823A
JC61-00695A
JC61-00696A
JC61-00697A
JC62-00002A
2001-000111
2001-000429
2001-000490
2001-000626
2001-000864
2201-000119
2201-000391
2202-000630
2401-000042
2401-002300
Description
CORE-FERRITE;AD,33x12x7mm,1500,2800Gauss
HEADER-BOARD TO CABLE;BOX,16P,2R,2mm,STR
SPRING-CS;SWP-B,YELLOW,PI1.3,D6.8,L45,-,
ICT-HINGE SHAFT(4IN1);SCX-1150F,SWCH,5.0
PMO-SLEEVE ADF;SCX-1110F,-,POM,BLK,-,-,PMO-SLEEVE PICK UP;SCX-1110F,-,POM,BLK,HINGE-M-CAM;SCX-4216F,POM,-,-,-,WHITE,-,
HINGE-M-FRAME;SCX-4216F,POM,-,-,-,WHITE,
HINGE-M-PRESSURE;SCX-4216F,PC(LF1025),-,
HEAT SINK-(4500);ML-4500,BRONZE,0.5,9.3,
C-CERAMIC,DISC;100NF,+80-20%,50V,Y5V,TP,
C-CERAMIC,DISC;0.022NF,5%,50V,SL,TP,5X3M
C-CERAMIC,MLC-AXIAL;100nF,10%,50V,X7R,TP
C-AL;100uF,20%,16V,GP,TP,6.3x7,5
C-AL;47uF,20%,50V,GP,TP,6.3x11,5
͢͢
DNA : DELIVERY
not AVAILABLE
Location
H3011
H3012
H3016
SNA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
Exploded View & Parts List
8
Up-date On August. 2. 2004
8. Exploded Views and Parts List
8.1 Main Assembly Exploded view ............................................................................... page(8-2)
8.2 Rx Drive Ass’y Exploded view ................................................................................ page(8-5)
8.3 ADF Assembly Exploded view ................................................................................ page(8-6)
8.4 OPE Assembly Exploded view ................................................................................. page(8-10)
8.5 Scanner Assembly Exploded view ......................................................................... page(8-12)
8.6 Middle Cover Assembly Exploded view ................................................................. page(8-14)
8.7 Frame Ass’y Exploded view .................................................................................... page(8-15)
8.8 Fuser Ass’y Exploded view ..................................................................................... page(8-19)
8.9 MP Assembly Exploded view .................................................................................. page(8-21)
8.10 Cassette Ass’y Exploded view .............................................................................. page(8-23)
8.11 SCF(Option Cassette Frame) Exploded view ....................................................... page(8-25)
Exploded drawings and service parts lists are given for items which may
be expected to have a higher failure rate.
Where a failure occurs you can identify the part in the exploded diagram
and, using the parts cross reference number, refer to the appropriate parts
list to identify the part number.
Note : Parts numbers given here are correct at the time of publication.
When ordering parts please use the on-line ordering system to check if
there have been any changes to part numbers.
Part Number & Description format.
Part numbers and descriptions are defined according to a company standard. The information below
will help you to understand the part number format and assist when ordering spare parts.
There are two types of Part number format.
number
letter
This format is used throughout Samsung on all product ranges.
Typically it is used for small components and electronic parts.
This format is controlled by individual Samsung Divisions and is used on specific
products, typically for mechanical parts. Type 2 format part numbers fall into 2 categories:
Assemblies consisting of 2 or more parts. Also used for Service manuals,
user guides and diagrams.
Ass’y parts and A/S privately used Parts can be distinguished by the part Code and Description.
They are always Type 2 format. The 2 leading characters indicate private or assembly parts.
Service Manual
Samsung Electronics
8-1
8-2
1-3
SCX-4520
SCX-4720F
SCX-4520
1-1
SCX-4720F
1-4
1-2
1-2
1
Toner Cartridge
22-8
22-13
21-2
22-5
0
22-9
22-10
22-6
22-4
22-7
22-1
22-3
22-2
21-4
21-3
21-1
20
21
22-12
22-11
7
19-1
15
22
3
19-3
19-4
24
4
25
19
18
10
19-2
9
6
12
16
8
17
17-1
5
23
13
2
17-2
27
11
26
23-2
23-1
14
SCF
8.1 Main Assembly
Service Manual
Samsung Electronics
Main Assembly Parts List
SA : Service Available
O : Service available X : Service not available
No.
SEC.Code
Q’ty
SA
ELA HOU-SCAN
JC96-03181A
1
X
SCX-4520
ELA HOU-SCAN
JC96-03184A
1
X
SCX-4720F
1-1
ELA HOU-ADF
JC96-03169A
1
O
1-2
ELA HOU-OPE
JC96-03183A
1
O
SCX-4520
ELA HOU-OPE
JC96-03174A
1
O
SCX-4720F
COVER-M-OPE FRONT
JC63-00496A
1
O
0
Description
Remark
SCX-4520
SCX-4720F
1
1-3
ELA HOU PLATEN
JC96-03172A
1
O
2
1-4
FRAME-M-BASE
JC61-00906A
1
X
3
ELA UNIT-RX DRIVE
JC96-03078A
1
O
4
UNIT-HUMMINGBIRD LSU
JC59-00018B
1
O
5
CBF HARNESS-LSU
JC39-00395A
1
O
6
SMPS-V1
JC44-00070A
1
O
110V
SMPS-V2
JC44-00071A
1
O
220V
7
PBA MAIN-MAIN CONTROLLER
JC92-01597A
1
O
SCX-4720F
PBA MAIN-MAIN CONTROLLER
JC92-01598A
1
O
SCX-4520
8
SHIELD-P-CONTROLLER
JC63-00508A
1
X
9
BRACKET-P-DUMMY CTRL
JC61-00679A
1
X
10
MEA UNIT-SHIELD ENGINE
JC97-01943A
1
X
11
BRACKET-P-INLET
JC61-00693A
1
X
12
CBF HARNESS-HIGH LIU
JC39-00325A
1
O
13
PBA SUB-LIU
JC92-01599A
1
O
RUSSIA
PBA SUB-LIU
JC92-01599B
1
O
EU/SER
AUSTRALIA
PBA SUB-LIU
JC92-01599C
1
O
14
COVER-M-SIDE R
JC63-00499A
1
O
15
ELA UNIT-MP
JC96-03132B
1
O
16
CBF HARNESS-MOTOR
JC39-00355A
1
O
17
MEA ETC TR
JC97-01917A
1
O
17-1
ROLLER-TRANSFER R2
JC66-00703A
1
X
17-2
GEAR-TRANSFER
JC66-00395A
1
X
18
ELA HOU-COVER MIDDLE
JC96-03247A
1
O
19
MEA-COVER MID FRONT
JC97-02043A
1
O
19-1
COVER-M-MID FRONT
JC63-00497A
1
O
19-2
CAP-M-SUB ACTUATOR
JC67-00068A
1
X
19-3
PMO-M-SUB ACTUATOR
JC72-01339A
1
X
19-4
SCREW-TAPTITE
6003-000196
1
X
Service Manual
Samsung Electronics
8-3
Main Assembly Parts List
No.
SEC.Code
Q’ty
SA
Remark
20
MEA UNIT-CASSETTE
JC97-02020A
1
O
21
ELA HOU-COVER SIDE L
JC96-03185A
1
O
21-1
COVER-SIDE L
JC63-00500A
1
X
21-2
COVER-DIMM
JC63-00501A
1
X
21-3
SPEAKER
3001-001591
1
O
21-4
SCREW-TAPTITE
6003-000264
2
X
MEA-COVER FRONT
JC97-02019A
1
O
22-1
COVER-M-FRONT
JC63-00505A
1
O
22-2
KNOB-M-LOCKER
JC64-00154A
1
X
22-3
HOLDER-M-LOCKER
JC61-00953A
1
O
22-4
TRAY-M-EXIT-MP
JC63-00447A
1
X
22-5
ADJUST-M-MP L
JC70-00478A
1
X
22-6
ADJUST-M-MP R
JC70-00479A
1
X
22-7
TRAY-M-COVER_MP
JC63-00446A
1
X
22-8
GEAR-PINION
JG66-40003A
1
O
22-9
TRAY-M-CASE_MP
JC63-00506A
1
X
22-10
TRAY-M-LINK_MP
JC63-00444A
2
X
22-11
SPRING-CIS(2)
JG61-70549A
1
X
22-12
SCREW-TAPTITE
6003-000196
2
X
22-13
SCREW-TAPTITE
6003-000264
1
X
MEA -COVER REAR
JC97-02018A
1
O
23-1
COVER-M-REAR
JC63-00503A
1
O
23-2
COVER-FACE UP
JC63-00504A
1
O
24
CBF HARNESS ENGINE
JC39-00240C
1
O
25
CBF HARNESS-LSU GND
JC39-00375A
1
O
26
ELA HOU-FUSER 110V
JC96-03210A
1
O
110V
ELA HOU-FUSER 220V
JC96-03260A
1
O
220V
FAN-DC
JC31-00025A
1
O
22
23
27
8-4
Description
Service Manual
Samsung Electronics
8.2 RX Drive Assembly
0
8
6
7
1
9
4
2
5
3
4
5
RX Drive Assembly Parts List
No.
Description
SEC.Code
Q’ty
SA
0
ELA UNIT-RX DRIVE
JC96-03078A
1
O
1
BRACKET-GEAR MAIN
JC61-00891A
1
X
2
GEAR-RDCN 53/26
JC66-00388A
1
O
3
GEAR-RDCN 113/33
JC66-00706A
1
X
4
GEAR-RDCN 57/18
JC66-00389A
2
O
5
WASHER-PLAIN
6031-000023
2
X
6
BRACKET-MOTOR MAIN R2
JC61-00916A
1
X
7
GEAR-RDCN 103/41
JC66-00390A
1
O
8
GEAR-RDCN 90/31
JC66-00392A
1
O
9
MOTOR STEP-MAIN
JC31-00037A
1
O
Remark
Service Manual
Samsung Electronics
8-5
8.3 ADF Assembly
5
5-1
5-2
6
5-3
6-3
5-2
0 : Service Part
6-1
*ELA HOU-ADF_R2
(JC96-03169A)
6-2
ADF ASS’Y
1-2-4
1
1-2-1
1-2
1-2-2
1-2-3
4
1-1
3-4
3-3
3-7
3-8
3-14
3-6
3-18
3-5
2-16
3-11
3-7
3-9
3-15
3-18
3-16
2-3
3-17
3-10
3-16
3-13
3-20
3-21
3-19
2-2
2-4
2-15
3-1
2-6
2-7
3-12
2-5
3-2
3-19
2-8
2-9
3-18
2-15
2
3
2-17
2-1
2-22
2-19
2-18
2-12
2-10
2-22
2-19
2-20
2-13
2-20
2-21
2-14
8-6
Service Manual
Samsung Electronics
ADF Assembly Continued.
4-3-2
4-3-3
4-3-4
4-3-5
4 : Service Part
*MEA-COVER PLATEN
(JC-97-02024A)
4-3-1
4-3
4-8
4-6
4-4
4-7
S
4-7
S
4-1
4-4
4-5
4-9
4-2
Service Manual
Samsung Electronics
8-7
ADF Assembly Parts List
No.
SEC.Code
Q’ty
SA
0
ELA HOU-ADF-R2
JC96-03169A
1
O
1
MEA UNIT-ADF UPPER
JC97-02022A
1
X
1-1
COVER-ADF UPPER R2
JC63-00450A
1
O
1-2
MEA-HOLDER PAD ADF
JC97-02137B
1
O
1-2-1
RMO-ADF RUBBER
JB73-00052A
1
X
1-2-2
HOLDER-PAD ADF
JC61-00893A
1
X
1-2-3
SPRING ETC-PAD
JC61-00387A
1
X
1-2-4
SHEET-ADF HOLDER
JC63-00373A
1
X
2
ELA HOU-ADF LOWER
JC96-03171A
1
X
2-1
COVER-M-ADF LOWER R2
JC63-00370B
1
O
2-2
PBA SUB-ADF
JC92-01618A
1
O
2-3
GROUND-P-ADF R2
JC63-00372A
1
X
2-4
SHAFT-M-FEED GEAR 38
JC66-00460A
1
X
2-5
ROLLER-DRIVE
JC66-00560A
1
X
2-6
PMO-ACT EMPTY ADF
JC72-01320A
1
O
2-7
PMO-ACTUATOR REGI SENSOR
JC72-01010A
1
O
2-8
PMO-ACTUATOR SCAN SENSOR
JC72-01011A
1
O
2-9
SPRING ETC-TORSION DOC (CC2-F)
JB61-00076A
3
X
2-10
IPR-GROUND_ROLLER
JC70-10467A
1
X
2-12
ROLLER-EXIT
JC66-00559A
1
X
2-13
MEC-BRUSH ANTISTATIC
JC75-00095A
1
X
2-14
PPR-WHITE BAR SHEET
JC72-00752A
1
X
2-15
PMO-BUSH
JB72-00819A
4
X
2-16
CBF HARNESS-ADF
JC39-00351A
1
O
2-17
GEAR-AGITATOR-2
JC66-00310A
1
X
2-18
RING-C
6044-000159
1
X
2-19
GUIDE-STACKER SUB
JC61-00712A
2
X
2-20
CBF HARNESS ADF ROLLER GND
JC39-00187A
1
X
2-21
IPR-BRKT WHITE BAR
JC70-00225A
1
X
2-22
SPRING ETC WHITE BAR
JC61-00548A
2
X
ELA HOU-ADF MOTOR
JC96-03065A
1
O
BRACKET-GEAR ADF
JC61-00892A
1
X
3-2
MOTOR STEP-ADF
JC31-00036A
1
X
3-3
GEAR-CLUTCH 29
JB66-00101A
1
X
3-4
PMO-WHITE CLUTCH SUB 29
JB72-00844A
1
X
3-5
GEAR-CLUTCH 39
JC66-00322A
1
X
3-6
RING-C
6044-000159
1
X
3-7
GEAR-IDLE 35 ADF
JC66-00458A
2
X
3-8
GEAR-40/21 ADF
JC66-00456A
1
X
3
3-1
8-8
Description
Remark
Service Manual
Samsung Electronics
ADF Assembly Parts List(cont.)
No.
Description
SEC.Code
Q’ty
SA
3-9
GEAR-SWING 31/20 ADF
JC66-00457A
1
X
3-10
LINK-M-SWING ADF
JC66-00454A
1
X
3-11
GEAR-58/25 ADF
JC66-00455A
1
X
3-12
IMPELLER-ADF
JC66-00556A
1
X
3-13
GEAR-REMOVE ADF
JC66-00557B
1
X
3-14
WASHER PLAIN
6031-000023
1
X
3-15
IPR-WASHER WAVE
JB70-00070A
1
O
3-16
WASHER-PLAIN
6031-000019
2
X
3-17
CBF HARNESS-ADF GND
JC39-00363A
1
X
3-18
RING-E
6044-000125
6
X
3-19
SCREW-TAPTITE
6003-000269
3
X
3-20
WASHER-PLAIN
6031-001511
1
X
3-21
SPRING ETC PAD
JC61-00387A
1
X
SEC.Code
Q’ty
SA
MEA-COVER PLATEN
JC97-02024A
1
O
4-1
COVER-M-PLATEN R2
JC63-00374B
1
O
4-2
SHEET-WHITE SPONGE
JC63-00209A
1
O
4-3
MEA-TX STACKER
JC97-01544B
1
O
4-3-1
PMO-TX STACKER
JB72-01166B
1
O
4-3-2
PMO-DOC GUIDE(L)
JB72-01171B
1
X
4-3-3
GEAR-PINION
JG66-40003A
1
O
4-3-4
PMO-DOC GUIDE(R)
JB72-01170B
1
X
4-3-5
IPR-WASHER SPRING CU
JF70-10616A
2
X
No.
4
Description
4-4
SPRING ETC-FEED
JC61-00011A
6
X
4-5
PMO-ROLL PINCH
JG72-40663A
2
X
4-6
ICT-SHAFT PINCH
JF70-40521B
1
X
4-7
MEA UNIT-HINGE
JC97-01707A
2
O
4-8
RPR-ROLLER EXIT IDLE
JC73-00091A
2
O
4-9
SHAFT-IDLE FEED
JC66-00558A
2
O
MEA-COVER OPEN R2
JC97-02023A
1
X
5-1
COVER-M-ADF OPEN
JC63-00498A
1
O
5-2
PMO-GUIDE PAPER
JB72-00843A
2
X
5-3
DAMPER-PICKUP ADF
JC66-00726A
1
X
MEA UNIT-PICKUP
JC97-01962A
1
O
6-1
STOPPER-M-PICKUP ADF
JC61-00963A
1
X
6-2
GEAR-ADF 38
JB66-00103A
1
X
6-3
RING-C
6044-000159
1
X
5
6
Remark
Remark
Service Manual
Samsung Electronics
8-9
8.4 OPE Unit Assembly
(SCX-4520)
(SCX-4720F)
0
0
21
2
20
1
2
1
8
10
19
5
8
4
5
3
6
3
17
7
10
4
18
9
6
16
11
7
14
12
15
9
11
12
13
13
8-10
Service Manual
Samsung Electronics
OPE Unit Assembly Parts List
[SCX-4520 ]
SEC.Code
Q’ty
SA
0
No.
ELA HOU-OPE 3IN1
Description
JC96-03174A
1
O
1
COVER-M-OPE (3IN1)
JC63-00496A
1
O
2
WINDOW-LCD_R2_SEC2
JC64-00171B
1
X
3
KEY-M_COPY(3IN1)
JC64-00054C
1
X
4
KEY-M-STOP
JC64-00055A
1
X
5
KEY-M_SCROLL_R2
JC64-00056D
1
X
6
KEY-M-START(3IN1)
JC64-00057B
1
X
7
KEY-M-TONER SAVE
JC64-00058A
1
X
8
KEY-M_RESOLUTION_R2
JC64-00059C
1
X
9
KEY-M-DIRECT PRINT
JC64-00155A
1
X
10
KEY-M-SCAN TO
JC64-00157A
1
X
11
RUBBER-COPY/SCROLL
JC73-00189A
1
X
12
RUBBER-COPY_3IN1
JC73-00192A
1
X
13
PBA SUB-OPE
JC92-01625A
1
O
S
SCREW-TAPTITE
6003-000196
7
X
SEC.Code
Q’ty
SA
Remark
[SCX-4720F ]
No.
Description
0
ELA HOU-OPE 4IN1
JC96-03174A
1
O
1
COVER-M-OPE SEC
JC63-00495A
1
X
2
WINDOW-LCD_R2_SEC
JC64-00171A
1
X
3
KEY-M_COPY_R2
JC64-00054C
1
X
4
KEY-M-STOP
JC64-00055A
1
X
5
KEY-M_SCROLL_R2
JC64-00056D
1
X
6
KEY-M-START
JC64-00057E
1
X
7
KEY-M-TOLL SAVE
JC64-00061A
1
X
8
KEY-M_RESOLUTION_R2
JC64-00059C
1
X
9
KEY-M-DIRECT PRINT
JC64-00155A
1
X
10
KEY-M-SCAN TO
JC64-00157A
1
X
11
RUBBER-COPY/SCROLL
JC73-00189A
1
X
12
RUBBER-TELL/FAX_SEC
JC73-00191A
1
X
13
PBA SUB-OPE_4720F
JC92-01625A
1
O
14
RUBBER-ONE TOUCH
JC73-00190A
1
X
15
KEY-M-TONER SAVE
JC64-00058A
1
X
16
KEY-M_FAX_R2
JC64-00060C
1
X
17
KEY-M-SHIFT
JC64-00156A
1
X
18
KEY-M_TEL_R2
JC64-00053D
1
X
19
PMO KEY OT
JC72-00275B
1
X
20
LABEL(P)-ONE TOUCH
JC68-00651G
1
X
21
MPR-COVER ADDRESS
JG74-10543A
1
X
S
SCREW-TAPTITE
6003-000196
10
X
Remark
Service Manual
Samsung Electronics
8-11
8.5 Scanner Assembly
1-3
1-3-1
1-3-2
1-3-4
1-3-3
0
1-1
1
1-5
1-4
1-5
1-2
2
2-15
2-2
2-15-4
2-15-7
2-15-6
2-15-5
2-9
2-15-3
2-5
2-3
? 2-15-8
2-10
2-11
2-6
2-8
2-15-1
2-13
2-12
2-7
2-16
2-15-2
2-4
2-1
2-14
8-12
Service Manual
Samsung Electronics
Scanner Assembly Parts List
No.
Description
SEC.Code
Q’ty
SA
0
ELA HOU-PLATEN
JC96-03172A
1
O
1
MEA UNIT-SCAN UPPER
JC97-02025A
1
O
1-1
COVER-SCAN UPPER
JC63-00494A
1
X
1-2
GLASS-SCAN
JC01-00001A
1
O
1-3
MEA-SCAN DUMMY
JC97-02026A
1
X
1-3-1
COVER-M-SCAN DUMMY R2
JC63-00152E
1
X
1-3-2
MCT-GLASS ADF
JC74-00021A
1
X
1-3-3
TAPE-DOUBLE FACE
0203-001266
1
X
1-3-4
LABEL(P)-SHADING
JB68-00644A
1
X
1-4
IPR-HOLDER GLASS
JB70-00148A
2
X
1-5
SCREW-TAPPING
6002-00175
2
X
ELA HOU-SCAN LOWER
JC96-03173A
1
X
2-1
COVER-SCAN LOWER
JC63-00493A
1
O
2-2
ELA HOU-CCD MODULE
JC96-02759B
1
O
2-3
CBF SIGNAL-CCD FFC
JC39-00367A
1
X
2-4
ICT-INSERT SHAFT
JB70-00154A
1
X
2
2-5
ICT-SHAFT CCD
JB70-00145A
1
X
2-6
PMO-HOLDER BELT
JB72-00764A
1
X
2-7
PMO-PULLEY
JB72-00763A
1
X
2-8
ELA UNIT-CORE
JB96-01381A
3
X
2-9
SPRING ETC-BELT
JB61-00059A
1
X
2-10
BELT-TIMING GEAR
6602-001067
1
O
2-11
PMO-LEVER SENSOR
JC72-00755A
1
X
2-12
PHOTO-INTERRUPTER
0604-001095
1
O
2-13
SPRING-CS
6107-001135
1
X
2-14
HOLDER-CCD
JC61-00894A
1
X
2-15
ELA HOU-SCAN MOTOR
JC96-03069A
1
O
2-15-1
BRACKET-SCAN MOTOR R2
JC61-00895A
1
X
2-15-2
MOTOR STEP-SCAN
JB31-00011A
1
X
2-15-3
GEAR-REDUCTION
JC66-00530A
1
X
2-15-4
GEAR-IDLE
JB66-00083A
1
X
2-15-5
GEAR-TIMING
JC66-00531A
1
X
2-15-6
PMO-HOLDER BELT
JB72-00764A
1
X
2-15-7
RING-E
6044-000125
1
X
CBF-HARNESS-PLATEN
JC39-00362A
1
X
2-16
Remark
Service Manual
Samsung Electronics
8-13
8.6 Middle Cover Assembly
0
2
5
6
4
1
3
Middle Cover Assembly Parts List
No.
8-14
Description
SEC.Code
Q’ty
SA
0
ELA HOU-COVER MIDDLE
JC96-03247A
1
O
1
COVER-M-MIDDLE R2
JC63-00502A
1
O
2
COVER-REAR UPPER
JC63-00388B
1
O
3
PMO-STACKE_RX
JC72-00973A
1
O
4
BUSH-F/DOWN R2
JC61-00902A
1
X
5
CBF HARNESS-OPE
JC39-00350A
1
O
6
PBA SUB-USB HOST
JC92-01636A
1
O
Remark
Service Manual
Samsung Electronics
Samsung Electronics
46-2
46-1
47-2
73
50
47-1
46
74
47-3
26
47-4
47
78
75
47-5
29
56
76
45-1
45-3
27-2
27-3
45-2
43
17
39
27-1
67 77
45
44
32
34
27
25
1
42
33
41
40
28
30
21
71
Transfer Roller
24
58
37
38
49
25
20
51
23
31
36
62
5
5
22
61
7
18
5
19
19-1
72
49
19-2
15
65
63-1
55
63-2
1
14
13
69
68
65-4
65-2
63
65-1
6
11
54
65-3
58
61
10
71
16
3
8
70
9
12
4
0
2
ELA HOU-FRAME
Unit Fuser
8.7 Frame Assembly
Service Manual
8-15
Frame Assembly Parts List
No.
SEC.Code
Q’ty
SA
Remark
ELA HOU-FRAME 110V
JC96-03186A
1
X
110V
ELA HOU-FRAME 220V
JC96-03187A
1
X
220V
1
FRAME-BASE R2
JC61-00906A
1
X
2
GUIDE-P-TR
JC61-00607A
1
O
3
PLATE-P-SAW
JC61-00604B
1
X
4
GUIDE-M-TR RIB
JC61-00594A
1
O
5
PMO-GEAR_EXIT_DRV16
JC72-00143A
3
X
6
FOOT-BACK
JC61-00835A
2
X
0
8-16
Description
7
FOOT-FRONT
JC61-00836A
2
O
8
GROUND-GUDIE TR R2
JC63-00397A
1
X
9
MEC-TERMINAL
JC75-00049A
4
O
10
PLATE-TERMINAL CON R2
JC61-00903A
3
X
11
PLATE-TERMINAL CR R2
JC61-00904A
1
X
12
HOUSING-TERMINAL R2
JC61-00911A
1
X
13
PMO-LOCKER CST
JC72-00983A
2
O
14
PMO-ACTUATOR CVR OPEN
JC72-00974A
1
O
15
PMO-PLATE GUIDE DEVE_R
JC72-00985A
1
O
16
SPRING ETC-GUIDE DEVE
JC61-70932A
2
O
17
GROUND-PUSH BUSHING
JC63-00401A
1
X
18
PMO-PLATE GUIDE DEVE_L
JC72-00984A
1
O
19
PMO-ACT FEED R2
JC72-01323A
1
X
20
PMO-ACTUATOR EMPTY
JC72-00975A
1
O
21
PMO-ACT MANUAL R2
JC72-01324A
1
O
22
GROUND-EARTH TR R2
JC63-00395A
1
X
23
GROUND-TERMINAL TR
JC63-00403A
1
X
24
ROLLER-FEED ROLLER 1
JC66-00526A
1
O
25
PMO-BUSHING FEED
JC72-00382B
5
X
26
SHAFT-FEED
JC66-00398A
1
O
27
MEA UNIT-PICKUP
JC97-01926A
1
O
27-1
SPONGE-ROLLER PICK_UP
JC72-01231A
1
O
27-2
HOUSING-PICK UP_R2
JC61-00909A
1
O
27-3
HOUSING-PICK UP2_R2
JC61-00910A
1
O
28
IPR-P-EARTH TRANSFER
JC70-00307A
1
O
29
HOLDER-PTL R2
JC61-00907A
1
O
30
LENS-PTL
JC67-00027A
1
O
31
PMO-BUSHING_TR(L)
JC72-00102A
1
O
32
SPRING ETC-TR L HAWK
JC61-00047A
1
O
33
ROLLER-FEED
JC66-00598A
1
O
Service Manual
Samsung Electronics
Frame Assembly Parts List(Cont.)
No.
Description
SEC.Code
Q’ty
SA
34
BUSH-M-TR L
JC61-00588A
1
O
36
SHAFT-FEED IDLE
JC66-00527A
1
O
37
BUSH-M-FEED IDLE
JC61-00585A
2
O
38
SPRING ETC-TR
JC61-70958A
2
X
39
GROUND-DRIVE2 R2
JC63-00398A
1
X
40
SPRING-TS
6107-001170
1
X
41
CAM-M-PICK_UP
JC66-00377A
1
O
42
GROUND-DRIVE R2
JC63-00394A
1
O
43
SOLENOID-FEED ROCKY2
JC33-00014A
1
O
44
SOLENOID-HB (MANUAL)
JC33-00010A
1
O
45
MEA UNIT-GEAR PICKUP
JC97-01929A
1
O
45-1
GEAR-PICK UP B_R2
JC66-00705A
1
X
45-2
GEAR-PICK UP A_R2
JC66-00704A
1
X
45-3
SPRING-CS
6107-001167
1
X
MEA UNIT-BRACKET FEED
JC97-01925A
1
O
BRACKET-FEED R2
JC61-00913A
1
O
46
46-1
46-2
GEAR-Z35 IDLE
JC66-00690A
1
X
MEA UNIT-CLUTCH
JC97-01788A
1
O
47-1
GEAR-FEED 1
JC66-00393A
1
O
47-2
PMO-COLLAR_SPRING
JC72-00978A
1
O
47-3
SPRING-TS
6107-001171
1
O
47-4
PMO-HUB CLUTCH
JC72-00981A
1
X
47-5
SHAFT-FEED
JC66-00398A
1
O
49
PLATE-PUSH BUSHING
JC61-00914A
2
X
50
GEAR-FEED 2
JC66-00394A
1
O
51
GEAR-IDLE 23
JC66-00396A
1
O
52
SPRING-TS
6107-001164
1
X
53
SPRING-TS
6107-001165
1
X
54
IPR-P-TERMINAL DEVE KEY
JC70-00340A
3
X
55
GROUND-TERMINAL DEVE
JC63-00458A
1
X
56
PBA SUB-PTL
JC92-01620A
1
O
58
HOLDER-TERMINAL R2
JC61-00908A
1
X
59
HOLDER-ACT MANUAL R2
JC61-00912A
1
X
61
HOLDER-BEARING EXIT F/DOWN
JC61-00829A
2
X
62
GEAR-EXIT F/DOWN
JC66-00038A
1
O
63
ROLLER-EXIT F/DOWN
JC66-00378A
1
O
64
RMO-RUBBER EXIT
JC73-40915A
4
O
47
Remark
Service Manual
Samsung Electronics
8-17
Frame Assembly Parts List(Cont.)
No.
65
8-18
Description
SEC.Code
Q’ty
SA
MEA RACK-EXIT ROLLER
JC97-01034A
4
X
65-1
PMO-HOLDER EXIT ROLL
JC72-41006A
1
X
65-2
PMO-ROLLER FD F
JC72-41007A
1
X
65-3
PMO-ROLLER FD R
JC72-41008A
1
X
65-4
SPRING ETC-EXIT ROLL FD
JC61-70911A
1
X
66
GUIDE-SUB FRONT
JC61-00917A
1
X
68
PBA-SUB-CRUM
JC92-01605A
1
O
69
CBF HARNESS CRUM2
JC39-00356A
1
X
70
PBA SUB-EXIT SENSOR
JC92-01604A
1
O
71
GROUND-SHIELD R2
JC63-00402A
1
X
72
LABEL(R)-HOT CAUTION,KME
JC68-00317A
1
X
73
BUSH-M-PICK_UP L
JC61-00586A
1
O
74
SHAFT-P-PICK_UP
JC66-00399A
1
O
75
STOPPER-PICK UP_R2
JC61-00915A
2
X
76
PMO-IDLE PICK_UP
JC72-00982A
2
X
77
BUSH-M-PICK_UP R
JC61-00587A
1
O
78
SHAFT-CORE
JC66-00720A
2
X
Remark
Service Manual
Samsung Electronics
8.8 Fuser Assembly
0
36
6
12
14
17
34
4
38
1
5
29
37
3
31
29
37
13
32
35
15
30
11
16
33
20
23
19
18
21
25
28
24
22
9
8
36
10
7
27
38
26
Service Manual
Samsung Electronics
8-19
Fuser Assembly Parts List
No.
SEC.Code
Q’ty
SA
Remark
ELA HOU-FUSER 110V
JC96-03210A
1
O
110V
ELA HOU-FUSER 220V
JC96-03260A
1
O
220V
1
COVER-FUSER R2
JC63-00363A
1
X
2
HOLDER-PLATE CLAW R2
JC61-00886A
4
X
3
SPRING ETC-CLAW
JC61-00064A
4
X
4
PMO-ROLLER_EXIT
JC72-40361A
2
X
5
SPRING ETC-FUSER EXIT
JC61-70976A
2
X
6
THERMOSTAT-150
JC47-00005A
1
O
7
PMO-GEAR_EXIT_DRV16
JC72-00143A
1
X
8
GEAR-IDLE 23
JC66-00396A
1
O
9
RING-E
6044-000125
1
X
10
GEAR-RDCN 25/15
JC66-00397A
1
O
11
ROLLER-HEAT_210
JC66-00729B
1
X
12
ELECTRODE-LFET R2
JC70-00473A
1
X
13
THERMISTOR-NTC
1404-001337
1
X
14
ELECTRODE-RIGHT R2
JC70-00472A
1
X
15
CBF HARNESS-FUSER 110V
JC39-00353A
1
X
WHITE
CBF HARNESS-FUSER 220V
JC39-00354A
1
X
BLACK
16
BUSH-HR R_R2
JC61-00887A
1
X
17
LABEL(P)-CAUTION, HOT_FUSER
JC68-30928D
1
X
18
RMO-RUBBER_EXIT
JC73-00017A
2
X
19
ROLLER-M-EXIT F/UP
JC66-00380A
1
O
20
ROLLER-PRESSURE
JC66-00600B
1
O
21
BEARING-PRESSURE/R
JC66-10901A
2
X
22
SPRING-CS
6107-001168
2
X
23
PMO-BUSHING TX
JC72-00382A
3
X
24
HOLDER-ACTUATOR
JC61-00581A
1
X
25
PMO-ACTUATOR EXIT R2
JC72-01319A
1
X
26
FRAME-FUSER R2
JC61-00890A
1
X
27
GUIDE-INPUT R2
JC61-00889A
1
X
28
SPRING-TS
6107-001165
1
X
0
8-20
Description
29
NUT-HEXAGON
6021-000222
5
X
30
BUSH-HR L_R2
JC61-00888A
1
X
31
PLATE-P-CLAW
JC61-00605A
4
X
32
GEAR-FUSER R2
JC66-00695A
1
X
33
LAMP-HALOGEN 110V
4713-001182
1
O
110V
LAMP-HALOGEN 220V
4713-001183
1
O
220V
34
LABEL(R)-LV FUSER
JC68-00408A
1
X
35
SCREW-TAPTIEE
6003-000196
1
X
36
SCREW-ASS'Y MACH
6006-001193
6
X
37
SCREW-TAPTIEE
6003-000269
6
X
38
BRUSH-ANTISTAIC
JC75-00095A
1
X
Service Manual
Samsung Electronics
8.9 MP Assembly
0
26
11
12
28
14
2
23
14
23
25
1
21
7
25
3
30
18
9
24
31
29
10
16
20
17
13
6
15
5-1
5-3
5
27
19
4
5-2
19
Service Manual
Samsung Electronics
8-21
MP Assembly Parts List
No.
0
1
2
3
4
5
5-1
5-2
5-3
6
7
9
10
11
12
13
14
15
16
17
18
19
20
21
23
24
25
26
27
28
29
30
31
8-22
Description
ELA UNIT-MP
FRAME-17-MP
SOLENOID-MP
CBF HARNESS-MPF SEN
BUSH-M-PICK-UP R
MEA UNIT-PICK UP
HOUSING-M-PICK UP2_R2
HOUSING-M-PICK UP_MP
RUBBER-PICK UP_MP
STOPPER-M-PICK UP_R2
HOLDER-M-PAD_MP
HOLDER-M-SENSOR_MP
PLATE-P-KNOCK UP_MP
BRACKET-P-PICK UP_MP
GEAR-IDLE 23
SHAFT-P-PICK_UP
ROLLER-M-IDLE FEED
GEAR-M-PICK UP_MP
GEAR-M-HOLDER_MP
CAM-M-PICK UP_MP
PMO-ROLLER CAM_MP
PMO-IDLE PICK UP
PMO-M-ACT EMPTY MP
RPR-FRICTION PAD
SPRING-ETC-EXIT ROLL FD
RPR-PAD CASSETTE
SPRING-ES
SHEET GUIDE PAPER R2
SHAFT-P-CORE
SHEET GUIDE MP
SPRING-CS
SPRING-ES
PHOTO INTERRUPTER
SEC.Code
Q’ty
SA
JC96-03132B
JC61-00923A
JC33-00015B
JC39-00365B
JC61-00587A
JC97-02034A
JC61-00909A
JC61-00925A
JC73-00194A
JC61-00915A
JC61-00924A
JC61-00926A
JC61-00927A
JC61-00932A
JC66-00396A
JC66-00399A
JC66-00529A
JC66-00710A
JC66-00709A
JC66-00711A
JC72-00761A
JC72-00982A
JC72-01338A
JC73-00140A
JC61-70911A
JC73-00141A
6107-001237
JC63-00545A
JC66-00720A
JC63-00448A
6107-001167
6107-001047
0604-001095
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
1
1
1
2
1
1
2
1
2
1
2
1
1
1
1
O
X
X
X
O
O
O
X
X
X
O
X
X
X
O
O
O
X
X
X
X
X
X
O
X
X
X
X
X
X
X
X
O
Remark
Service Manual
Samsung Electronics
8.10 Cassette Assembly
0
12
14
13
6
16
4
6-4
6-3
6-2
6-1
15
5
3
7
5
2
10
11
1
17
8
Service Manual
Samsung Electronics
8-23
Cassette Assembly Parts List
No.
8-24
Description
SEC.Code
Q’ty
SA
0
MEA-CASSETTE
JC97-02020A
1
O
1
FRAME-M-CASSETTE
JC61-00876D
1
O
2
GUIDE-M-EXTENSION LARGE
JC61-00918B
1
X
3
PMO-EXTENSION SMALL
JC72-00971A
1
O
4
PLATE-P-KNOCK_UP
JC61-00603A
1
X
5
SPRING-CS
6107-001166
2
X
6
MEA UNIT-HOLDER PAD
JC97-01931A
1
O
6-1
HOLDER-M-PAD
JC61-00580A
1
O
6-2
SHEET-HOLDER PAD R2
JC63-00407A
1
X
6-3
RPR-FRICTION PAD
JC73-00140A
1
O
6-4
IPR-PLATE PAD
JC70-00314A
1
O
7
SPRING ETC-EXIT ROLL FD
JC61-70911A
1
X
8
COVER-M-SUB CASSETTE R2
JC63-00490A
1
X
10
PMO-PLATE_LOCKER
JC72-00972A
1
O
11
SPRING ETC-LOCKER,PLATE
JG61-70531A
1
O
12
ADJUST-M-CASSETTE_L
JC70-00300A
1
O
13
ADJUST-M-CASSETTE_R
JC70-00301A
1
O
14
GEAR-PINION
JG66-40003A
1
O
15
RPR-PAD CASSETTE
JC73-00141A
1
X
16
CAM-KNOCK UP
JC66-00719A
1
X
17
INDICATOR-CST PAPER
JC64-00143A
1
X
Remark
Service Manual
Samsung Electronics
42
1
39-3
38
39-8
0
Samsung Electronics
40
39-6
39-10
39-7
39-4
39-2
28
39-1
39-5
1-3
20
21
39-9
1-4
34
23
39
22
24
19
18
37
17
11
15
13
33
32
9
10
16
14
6
7
31
12
8
25
30
36
34
2
35
41
27
5
28
3
26
4
29
Service Manual
8-25
SCF(Option Cassette Frame) Assembly Parts List
No.
8-26
Description
SEC.Code
Q’ty
SA
0
ELA UNIT-SCF R2
JC96-03132B
1
O
1
COVER-M-FRONT SCF R2
JC63-00505A
1
O
2
COVER-M-SIDE L SCF
JC63-00500A
1
X
3
COVER-M-SIDE R SCF
JC63-00499A
1
O
4
COVER-M-REAR SCF R2
JC63-00503A
1
O
5
FRAME-M_SCF
JC61-00877A
1
X
6
HOUSING-M-PICKUP_R2
JC61-00909A
1
O
7
HOUSING-M-PICKUP2_R2
JC61-00910A
1
O
8
SPONGE -ROLLER PICK_UP
JC72-01231A
1
O
9
SHAFT-P-CORE
JC66-00720A
2
X
10
PMO-BUSHING FEED
JC72-00382B
2
O
11
BUSH-M-PICK_UP L
JC61-00586A
1
O
12
BUSH-M-PICK_UP R
JC61-00587A
1
O
13
SHAFT-P-PICK_UP
JC66-00399A
1
O
14
PMO-IDLE PICK_UP
JC72-00982A
2
X
15
ROLLER -FEED
JC66-00598A
1
O
16
PMO-BUSHING TX
JC72-00382B
2
O
17
PMO-GEAR PICK_UP A
JC72-00979A
1
X
18
PMO-GEAR PICK_UP B
JC72-00980A
1
X
19
SPRING-CS
6107-001167
1
X
20
RING-CS
6044-000001
1
X
21
CAM-M-PICK_UP
JC66-00377A
1
O
22
SHAFT-FEED
JC66-00527A
1
O
23
GEAR -FEED 2
JC66-00394A
1
O
24
SPRING-TS
6107-001170
1
X
25
PCB-SENSOR
JC41-00247A
1
X
26
PBASUB-SCF
JC92-01614A
1
O
27
CBF HARNESS -SCF GND
JC39-00366A
1
X
28
CBF HARNESS -SCF
JC39-00357A
1
X
29
COVER-M-SIMM R2
JC63-00492A
1
X
30
SHEET-COVER SENSOR
JC63-00369A
1
X
31
PMO-ACTUATOR EMPTY
JC72-00975A
1
O
32
IPR-GND TOP
JC70-11028A
1
X
33
SOLENOID-HB(MANUAL)
JC33-00010A
1
X
34
PMO-LOCKER CST
JC72-00983A
1
O
35
FOOT-BACK
JC61-00835A
1
O
36
FOOT-FRONT
JC61-00836A
2
O
37
SCREW-ASS’Y TAPT
6006-001078
1
X
Remark
Service Manual
Samsung Electronics
SCF(Option Cassette Frame) Assembly Parts List
No.
Description
SEC.Code
Q’ty
SA
38
SCREW-TAPTITE
6003-000196
10
X
39
ELA HOU-MOTOR SCF
JC96-03003A
1
O
39-1
BRKT-P-MOTOR SCF
JC61-00879A
1
X
39-2
BRKT-P-GEAR SCF
JC61-00881A
1
X
39-3
BRKT-M-FEED SCF
JC61-00878A
1
X
39-4
GEAR 61/47 IDLE
JC66-00688A
1
X
39-5
GEAR 59 IDLE
JC66-00689A
1
X
39-6
GEAR 35 IDLE
JC66-00690A
1
X
39-7
GEAR-RDCN 57/18
JC66-00389A
1
X
39-8
GEAR-IDLE 23
JC66-00396A
1
X
39-9
MOTOR STEP(SCF)
JC31-00009A
1
O
39-10
SCREW-MACHINE
6001-000131
5
X
39-11
CORE-FERRITE
3301-001635
1
X
39-12
CABLE TIE
6501-000004
1
x
40
BUSH CABLE
JC61-00804A
1
X
41
SCREW-TAPTITE
6003-000196
1
X
42
MEC-CASSETTE
JC97-02020A
1
X
Remark
Service Manual
Samsung Electronics
8-27
MEMO
8-28
Service Manual
Samsung Electronics
Appendix (Parts code)
Update: 9/10/04
NO.
1
2
3
4
5
6
7
8
9
10
11
12
Buyer-Model Code
SCX-4720F/XAA
SCX-4520/XAA
SCX-4720F/XEC
SCX-4520/XEC
SCX-4720F/XEF
SCX-4520/XEF
SCX-4720F/XEG
SCX-4520/XEG
SCX-4720F/XEP
SCX-4520/XEP
SCX-4720F/XET
SCX-4520/XET
SCX-4720F/XEU
SCX-4520/XEU
SCX-4720F/XIL
SCX-4520/XIL
SCX-4720F/XSG
SCX-4520/XSG
SCX-4720F/XEV
SCX-4520/XEV
SCX-4720F/XSA
SCX-4520/XSA
SCX-4720F/XIP
ELA HOU-SCAN
ELA HOU-OPE
PBA SUB-LIU
JC96-03184A
JC96-03181A
JC96-03184B
JC96-03181B
JC96-03184C
JC96-03181C
JC96-03184D
JC96-03181D
JC96-03184J
JC96-03181J
JC96-03184E
JC96-03181E
JC96-03184A
JC96-03181A
JC96-03184F
JC96-03181F
JC96-03181A
JC96-03184G
JC96-03181G
JC96-03174A
JC96-03183A
JC96-03174B
JC96-03183B
JC96-03174C
JC96-03183C
JC96-03174D
JC96-03183D
JC96-03174J
JC96-03183J
JC96-03174E
JC96-03183E
JC96-03174A
JC96-03183A
JC96-03174F
JC96-03183F
JC96-03183A
JC96-03174G
JC96-03183G
JC92-01599A
-
-
-
JC96-03184A
JC96-03174A
JC92-01599A
JC92-01599B
JC92-01599B
JC92-01599B
JC92-01599B
JC92-01599B
JC92-01599B
JC92-01599A
JC92-01599A
Samsung Electronics
MA IN M OTOR
FL A TEN COVER SENSOR
STEP M OTOR
FL A TEN MOTOR
600 DPI
COL OR CCD
TEA3718 X 2EA
A DF MOTOR DRIVER
CL UTCH(TB D)
P-REGI, P-DET, P-POS
SENSOR
A DF UNIT
¡ K ey Sc an
¡ L CD/L ED Drive
¡ MICOM
OPE
L CD, 16*2 L INES
40P/60P
4P
3P
4P
24P
16P
6P
4P
USB 2.0
NETW ORK
36P
TEA3718 X 2EA
FL A TEN
MOTOR
DRIVER
CCD DRIVING
PA RT
HT82V26
A FE
FA ST SRA M
(128 K B yte)
UART I/F
NIC I/F CA RD
Ph y Ch ip
ISP1582
USB Driv er
Su p er 1284
BUS
RAM
BUS
DRAM
NA ND (32MB x
SIO I/F
USB HOST
OTG242
CX2049
3
L SD
DRA M B ac k u p
M EM ORY DIM M
Drv.
AUDIO
THERM.
SDRA M (32MB x
SSD
MODEM
SFX336
33.6K B P
ROM BUS
4P
2P
3P
2P
3P
2P
11P
12P
11P
2P
26P
+24VS
+24V
EXT.
PHONE
HVPS
OPC GND
THV
DEV
P T L
REGI. CLUTCH
M AIN CLUTCH
MPF SENSOR
MPF CLUTCH
CRUM CARTRIDGE INFO.
MOTOR DRIVER
A3977 X 1EA
MHV
SUPPLY
M O D U LA R
JA C K
2P
2P
SCF(o p tio n )
USB HOST
JACK
SENSOR X 1EA
L S U
5P
LINE
COVER S/W
FEED SENSOR
MP EMPTY
SENSOR
EXIT SENSOR
INLET &
POWER S/W
+5V
PAPER EMPTY
SENSOR
AC 110V / 220V
SM PS
FUSER
POW ER
S/W
9
IEEE1284
Reset
Ro c k y2_Plu s _SEC s ys tem
Block Diagram
9. Block Diagram
Service Manual
9-1
Samsung Electronics
C C D M O D U LE
1
2
3
4
:
:
:
:
A
nA
B
nB
- 1 ST E P M O T O R
- 1 SE N SO R
SC F U nit(O ption)
MAIN MOTOR
P _D E T SE N SO R
P _R E G SE N SO R
P _P O S SE N SO R
REGI CLUTCH
TB D
ADF M OTOR
(ST E P M O T O R )
FLATEN MOTOR
(STEP MOTOR)
600D P I C O L O R
DGND
DGND
PI_TG
: PI_RS
: DGND
: CCD_HOME
VO B
VO G
: PI TG
: PI2
: CCD_PI_CP
: +24V
1: DGND
4: DGND
7 : ADF_PHA
10 : ADF_NA
13 : P_DET
16 : P_POS
2 :
6 :
10
14
18
22
1 : +3.3V
3 : OLD_SCF_CMD
5 : nOLD_SCF_RDY
7,8,9,10,11 : DGND
ADF MOTOR
DRIVER
(TEA3718 X 2EA)
A DF PB A
1 :
5 :
9 :
13
17
21
2 : nA
4 : nB
2 : nA
4 : nB
2 : nOLD_SCF_STS
4 : OLD_SCF_CLK
6 : +24V
1 : A
3 : B
+24V 3 : +5V
ADF_NA
6 : ADF_PHB
ADF_B
9 : ADF_NA
: DGND
12 : P_DET
: P_REG
15 : DGND
1 : A
3 : B
: DGND
VO R
DGND
: DGND
: DGND
2 : +5V
4 : RESET
6 : LED8
DGND
4 :
DGND
8 :
: PI TG
12
: PI1
16
: +5V 20 : DGND
: INV_PW R
24
2 :
5 :
8 :
11
14
3 :
7 :
11
15
19
23
1 : +5V
2 : SIG NAL
3 : GND
1 : DGND,
3 : TXD,
5 : RXD
NIC I/F
SUPER1284
IEEE1284
TEA3718 X
2EA
FL A TEN
MOTOR
DRIVER
R
A
M
B
U
S
D
R
A
M
B
U
S
MA IN B ’d
USB CONTROL L ER
ISP 1582(Ph ilip s )
USB HOST
OTG242
CX20493
L SD
SPK DRV.
M EM ORY DIM M
SDRAM(32MB X 2ea)
SSD
MODEM
SFX336
33.6K B P
ROM BUS
NAND(32MB X 1ea)
2 :
5 :
8 :
11
14
17
20
23
26
:
:
:
:
:
:
MODEM_RX
MODEM_TX_1
DG ND
CML
nRING
nDP
1 : SIG NAL
1 : +24VS
1 : +24VS
1 : SIG NAL
+5V
DGND
DGND
: +24VS
: N.C
: THV_PW M
: MHV_PW M
: FAN
2 : SIG NAL
2 : N.C
2 : SIG NAL
2 : SIG NAL
2 : DGND
3 : +24VS
3 : +5V
2 : DGND
4 : MODEM_TX_2
6 : REMOTE
8 : nEXT_PHONE
10 : +5V
9
2 : THERMISTER
1 : +3.3V
2: CART_DIN
3 : CART_DOUT 4 : DGND
1 : +5V
1 : SPK+2 : SPK-
1
3
5
7
9
11
3 :
6 :
9 :
12
15
18
21
24
PAPER EXIT
SENSOR
P_FEED
DGND
DGND
: +24VS
: +24V
: N.C
: DEV_PW M
: N.C
: P_EXIT
1 : LSU CLK
2 : nLREADY
3 : nPMO TOR
4,8 : DGND
5 : +24VS
6 : nHSYNC
7 : +5V 10 : VDO
: nLD_ON
11 :LSU_READ
1 : THERMISTER
P_EMPTY
+5V
N.C
: DGND
: P_EMPTY
: THV_READ
: THV_EN
: N.C
: FUSER_ON
SENSOR
MP SENSOR
P_EMP SEN.
EXIT SEN.
FEED SEN
MA IN
CLUTCH
REGI
CLUTCH
MPF
CLUTCH
MPF
SENSOR
CA RTRIDGE
PT L
SP K
L IU PB A
L SU
THERMISTOR
FUSER
FA N
SWITCH
- DOOR OPEN
-
SM PS / HVPS PB A
PWR S/W
10
FLAT COVER OPEN
SENSOR
HT48C50(HOL TEK )
OPE PB A
L CD MODUL E
16 X 2LINE
1 :
4 :
7 :
10
13
16
19
22
25
Connection Diagram
10. Connection Diagram
Service Manual
10-1
Schematic Diagram
11. Schematic Diagrams
11.1 Main Board(1/15)
Service Manual
Samsung Electronics
This Document can not be used without Samsung’s authorization.
11-1
Main Board(2/15)
11-2
Schematic Diagram
Service Manual
Samsung Electronics
Main Board(3/15)
Schematic Diagram
Service Manual
Samsung Electronics
11-3
Main Board(4/15)
11-4
Schematic Diagram
Service Manual
Samsung Electronics
Main Board(5/15)
Schematic Diagram
Service Manual
Samsung Electronics
11-5
Main Board(6/15)
11-6
Schematic Diagram
Service Manual
Samsung Electronics
Main Board(7/15)
Schematic Diagram
Service Manual
Samsung Electronics
11-7
Main Board(8/15)
11-8
Schematic Diagram
Service Manual
Samsung Electronics
Main Board(9/15)
Schematic Diagram
Service Manual
Samsung Electronics
11-9
Main Board(10/15)
11-10
Schematic Diagram
Service Manual
Samsung Electronics
Main Board(11/15)
Schematic Diagram
Service Manual
Samsung Electronics
11-11
Main Board(12/15)
11-12
Schematic Diagram
Service Manual
Samsung Electronics
Main Board(13/15)
Schematic Diagram
Service Manual
Samsung Electronics
11-13
Main Board(14/15)
11-14
Schematic Diagram
Service Manual
Samsung Electronics
Main Board(15/15)
Schematic Diagram
Service Manual
Samsung Electronics
11-15
Schematic Diagram
11.2 LIU Board
11-16
Service Manual
Samsung Electronics
Schematic Diagram
11.3 OPE Board
Service Manual
Samsung Electronics
11-17
Schematic Diagram
11.4 USB Host Board
11-18
Service Manual
Samsung Electronics
Schematic Diagram
11.5 SMPS_110V
Service Manual
Samsung Electronics
11-19
Schematic Diagram
11.6 SMPS_220V
AR1
C3
DSS-601M
F1
250V8A
LF1
SW0610V
C101
1KV2 22
C2
472MAA* 2
F2
250V3.15A
LF2
CH925130
B101
TH1
8D-15
CON2-16
1/2W3.3K * 10
INL ET
24V(0.7A)
1/2W
560K
C5
400V
220uF
30* 30
INL ET
SW1/B
R15
9
5
D5
UF4007
R131
R130
R129
R107
R106
C102
WB
35V1000uF
R105
R2
R104
C4
474
7
R103
R1
C6
1KV223
R14
R5
3W47K
6
R102
C1
474
1/4W 82K* 2
TNR1
10D561K
1/4W 330K* 2
BD1
D3SBA60
R117
50m
D101
200V10A
R113
SW1
3024-P3T4DBKBKR 2
SW2
CON2-11,12,1 3
24VS(2.5A)
SS-5GL
R118
50m
C105
50V1uF
C9 1
1KV221
CON2-9,10,18
R3
L1
AY70
C106
1K471
C7
35V47uF
D6
200V1A
R11
C10
1W47
630V333
FUSIBLE
R8
12K
ZD4
18V
D7
1N4148
R12
1W180
FUSIBL E
PC102
TLP3061F
GA T E 5
R10
22
5V(1.5A)
B1
D102
Q2
SPA07N60C3
R16
220
D103
40V3A* 2
C107
WB
10V1500uF
PC101
817M-B
C108
50V1uF
12
R7
200
U101
TL 431
C15
222
C8
105
4
R111
2.7KF
R109
N.C
10
I- SENSOR 4
R17
220
L101
5uH
R110
1K
3
3 F/B
7 GND
C11
50V104
VC C 6
Q1
BTA12-600B
2 SOFT -ST A RT
U1
ICE2BS01
F101
250V2A CON2-3,4
R6
1/4W22
CON1
R13
1/4W22
GND
C109
10V470uF
R108
1W150J
R112
2.6KF
R9
W.W 1N0.47
C14
333
PC101
817M-B
R114
1/2W1.5K
CON2-5,6,7
GND
PT1
C13
472MAA
EER3435V
24VS
C12
472MAA
FUSER-ON
Q102
C1008-Y
5V
5V
R127
1/4W150
CON3
+24VS
5V
R132
1/4W 150MI NI
R125
1/4W150
CON3-3
R126
47K
R128
47K
PAPER EMPTY
R115
1/4W150
CON2-1
R119
2.2K
CON2-23
OP102
KPI -512
CON3-2
CON3-1
FAN
FEED SENSOR
OP103
KPI -512
D105
1N4003
CON2-14
CON2-2
OP104
2G-288
R116
47K
MA NUAL
R120
5.6K
Q101
KSC1008-Y
GND1
GND2
ZD2
ZD1
200V 200V 200V
R133
47K
3
2
CON2-1
FEED-SEN
CON2-2
PAPER-EMPT
CON2-17
THV-PWM
CON2-14
MANUAL
CON2-15
THV-READ
CON2-20
THV-EA
CON2-19
CON4
1
11-20
ZD3
TNR101
EXI T
OPC1
CON2-24
7D561
D GND
BIAS-PWM
CON2-22
MH V-PWM
CON2-21
N.C
CON2-23
FAN
CON2-24
EXI T
CON2-25
N.C
CON2-26
FUESR-ON
Service Manual
Samsung Electronics
Schematic Diagram
11.7 HVPS
5V
24V
5V
R209
100K
C115
104
IT201
R202
100
THV PWM
CN2-#17
9
THV
4
R210
5.6KJ
R201
430
THV-sen >>
5 +
7
6 -
R203
2KJ
47K
C201
MY2A473
R205
22K
6
1
7
D204
D205
6KV
C211
6KV221
D206
6KV
C209
>> THV
6KV221
Q203
C2383
D203
D1NL20U
R207
C205
330KJ
MY- 2A471
C203
681
5
6KV
THV
100K
C202
102
C210
6KV221
2
R208
10K
4
R204
C206
MY-2A104
U102/B
KA324
Q202
945C-Y
11
Q201
A708-Y
D201
1N4148
8
C212
2KV221
D202
D1NL20U
ZD201
2.7VB
R212
RDS1/2W100KJ
C208
MY-2A681
VA201
7N221K
VA202
7N431K
R213
BLR1/2W100MF
VA203
7N561K
R206
130KF
R211
1/4W4.7J
R302
470K
5V
D
24V
C302
CE-103
IT301
R301
5.6K
THV -EA
CN1-#20
THV
3
R303
470J
Q301
945C-Y
4
4
C301
MY2A104J
C303
103
C306
MY2A473J
INDEX
50K
THV REA
CN2-15
1
THV_READ
ZD302
2.7VB
R308
1KF
C307
MY2A473J
+
3
C304
3KV151
5
6
1
7
+5V
D305
1N4148
D303
1N4148
D301
D1NL20U
ZD301
2.7VB
R304
1/4W4.7
R305
BLR1/2W50MJ
>>THV-sen
R306
100KF
Q302
C2383
+5V
R309
3KF
R307
150KF
D302
4KV
2
D304
1N4148
C305
104
- 2
IC105/A
R310
200J
Service Manual
Samsung Electronics
11-21
Schematic Diagram
11.8 NPC Board
3.3V
3.3V
3.3V
3.3V
R3 3
200
C4
10PF,50V
10PF
,50V
100n
100nF
C1 5
3.3V
3.3V
3.3V
C1 3
100nF
100n
100n
100nF
C1 9
LED 1
LED1
LT-63216321-S4
1M ,1%
DG ND
R4 5
10K
S1F25000-35D 12M
S1F25000-
R4 6
100
C5
10PF,50V
10PF
,50V
XO
LED _C O N
LE
nR ES ET
R3 6
C2 1
100pF
100pF
NO POP
POP
200
DG ND
R3 9
1K
3
1
LED _C O N
LE
Q2
M M BT2222A
2222ALT1
MD IO
MDIO
3.3V
3.3V
DG ND
MD C
MDC
2
NO POP
POP
3.3V
3.3V
R4 4
U1
AT24C32N
24C3 2N
10K
4
DG ND
R3 5
330
R3 4
330
3
2
Q1
KS A1182KSA
1182-Y
1
BL-C 91G/E
BL
91G/EGWGW -01G01G-LC4
C4
2
1
R3 8
0
1
VS S
SD A
E2
SCLL
SC
6
E1
*W C
E0
VC C
VCC
R4
R5
1K
1K
NO POP
POP
21
2
22
3
23
4
24
5
25
6
26
7
27
8
28
9
29
10
30
11
31
12
32
13
33
14
34
35
36
37
6
15
7
DG ND
RX D3
RXD3
RX D2
RXD2
RX D1
RXD1
RX D0
RXD0
RX _D V
RX_DV
RX _C LK
RX_CL
RX _ERR
RX_ERR
TX _C LK
R4 1
33
TX _E
_EN
RA 3
39
16
TX D 0
TX D 1
TX D 2
TX D 3
8
17
CO L
COL
C3
100n
100nF
3
2
1
5
WL AN _LINK
INK
LED 2
LED2
C2 0
10uF
16V
0-8461684616-1
XI
OS C1
R1 0
C1 8
100n
100nF
CN 2-21
2-21
CR S
CRS
DG ND
18
38
19
39
20
40
DG ND
3
DG ND
LAN_LI
LAN
_LINK
ENPC V1.1
3.3V
3.3V
DG ND
3.3V
3.3V
AV ddT
DG ND
3.3V
3.3V
U2
R4 0
200
AV ddT
28
DG ND
nRESSET
nRE
ET
CR S
CO L
R1 9
R2 1
60
59
33
33
TXD33
TXD
TXD 2
TXD2
TXD 1
TXD1
TXD 0
TXD0
TX_EN
TX_CLK
R4 7
33
RX_ C LK
R4 8
33
RXD 0
RXD0
RXD11
RXD
RXD 2
RXD2
RXD 3
RXD3
RX_ ERR
RR
RX_ D V
MD C
MD IO
RA2
10K
10K
10K
5.1K
5.1K
MD INT
IN
RIP
RI
CR S
CO L
RXN
RXP
TX3
TX2
TX1
TX0
TX_ER
54
53
51
49
48
TX_EN
TX_CLK
RX_ ER
RX_ C LK
RX_ D V
42
41
R2 7
R2 6
R2 8
R8
RES ET
58
57
56
55
52
47
46
44
43
39
27
26
33
15
32
31
TXN
TXP
VCCA
VC
CA 1
VC CA 2
VCCA
VC CA 3
VCCA
VC CA 4
VCCA
VC CA 5
VCCA
GN
GN
GN
GN
GN
RXD00
RXD
RXD 1
RXD1
RXD 2
RXD2
RXD 3
RXD3
D A1
D A2
D A3
D A4
D A5
VCCE
VC
CE _I1
VC CE _I2
VCCE
VC CE _I3
VCCE
MD C
MD IO
PW DDW
DD W N
TES T
TES T_S
_SE
IREF
IR
GN D E_I1
GN D E_I2
GN D E_I3
NC11
NC
NC 2
NC2
NC33
NC
NC 4
NC4
3
61
29
D3
2
1
3
CN 1-1
1-1
XF ATM 2-C
-CO M BO 1-2
D4
9
R2
R3
8
49.9,1%
49.9,1%
DG ND
18
19
1
2
04-6232-106-103-800
X1
X2
DG ND
R2 4
100,1%
7
6
5
4
3
2
1
10
23
21
9
13
16
17
22
7
10
14
20
24
C9
39
45
62
DG ND
25
40
50
30
8
C8
C7
C11
C1 1
C1 2
C12
10pF
10p
10pF
10p
D23
2
DG ND
C6
DG ND
1
D13
2
1
04-6232-106-1 03-800
XI
XO
12
11
04-6232-106-1 03-800
100
0
100nF
R9
R1 1
C1 4
C14
100n
100nF
3.3V
3.3V
11-22
FG ND
C1
100n
100nF
FG ND
FG ND
FG ND
DG ND
EN PC V1.1
STE100P
E100P
DG ND
C2
100n
100nF
100nF
R3 1
10K
C 17
R3 0
10K
100nF
C23
1nF
10K
10K
10K
10K
10K
10K
10K
10K
100nF
R32
10K
R1 7
R1 8
R6
R7
R 12
R1 3
R 14
R1 5
C 10
C22
1nF
64
63
6
5
4
3
2
1
100nF
R2 9
10K
CG 0
CG 1
FD E
MF 0
MF0
MF 1
MF1
MF 2
MF2
MF 3
MF3
MF 4
MF4
100nF
10K
LEDR1
LED
R1 0
LED L
LEDL
LED C
LEDC
LED S
LEDS
LED TR
LEDTR
C 16
R3 7
D5
MM SD 914T
MMSD
914T1
38
36
35
34
37
100nF
MM SD 914T
MMSD
914T1
LAN _LINK
LAN_LI
04-6232-106-103-800
D6
DG ND
Service Manual
Samsung Electronics
Samsung mySingle
페이지 1 / 2
Fwd: Re: Re SCX4720 SM
작성자: jungyun Cho Partner(Staff)//Samsung Electronics (2004-06-17 10:18)
인쇄자: 이목현 G5(과장)/담당과장/품질혁신그룹(프린터)/삼성전자 (2004-06-21 13:45)
수신인: LEE MOK HYOUN Manager/Quality Innovation Group/Samsung Electronics
allan 에게만 보냈었네요. 제가 allan에게 보낸 메일입니다.
------- Original Message ------Sender : jungyun Cho<[email protected]> Partner(Staff)//Samsung Electronics
Date : 2004-06-17 10:16
Title : Re: Re SCX4720 SM
Dear Allan Smith
Thanks your advice!!
We correcting mentioned items from you.
I sent mail of three times to you yesterday and It attached Chapter 5 & 8 in second and third mail.
Please confirm single once again.
Have a nice day!!
JY Cho
------- Original Message ------Sender : AllanSmith<[email protected]> Staff/ECC(??)/????
Date : 2004-06-17 00:47
Title : Re SCX4720 SM
I have read the service manual and Ch 1,2,3,9 and 10 have only very few changes
Chapter 4, 6 and 7 have many changes.
I have not received Chapter 5 and 8.
Fits a general note for ALL service manuals
There must be
a SPACE character BEFORE (
a SPACE character AFTER )
but
). is OK
), is OK
This mistake is in many chapters and many products.
Now SCX4270 Chapter 1 ( make sure these changes are in ALL FUTURE SM)
Page 1-1
Change “con-forming”
To “conforming”
Page 1-2
Change “other wise”
To “otherwise”
Page 1-3
Change “burning cigarettes, etc on the printer, These could”
To “burning cigarettes, etc. on the printer, these could”
Chapter 2 – Ensure these change are in ALL FUTURE SM
Page 2-1
Change “tests pages”
To “test pages”
Use of ( and ) – see note above –
Change “DVM(Digital Volt Meter)”
To “DVM (Digital Volt Meter)”
Change ”An IPA(Isopropyl Alcohol)dry wipe”
To ”An IPA (Isopropyl Alcohol) dry wipe”
http://www.samsung.net/service/ml/RecvController
2004-06-21
Samsung mySingle
페이지 2 / 2
Page 2-3
Change “used in a factory”
To “used in the factory”
Change “The contents of the life span and the printing speed are measured with
the pattern shown in below. (The picture in the manual is 70% of the actual A4
size.)”
To “The life of the toner cartridge and the printing speed are measured using the
pattern shown below. (The image is 70% of the actual A4 size).”
Page 2-6 is missing
I believe that SCX4270 supports a wireless network option.
Please check and if wireless is supported then add Page 2-6 from the ML-2150 SM.
Allan Smith
ECC
http://www.samsung.net/service/ml/RecvController
2004-06-21
12
11
10
9
8
7
6
5
4
3
2
1
NO.
SCX-4720F/XAA
SCX-4520/XAA
SCX-4720F/XEC
SCX-4520/XEC
SCX-4720F/XEF
SCX-4520/XEF
SCX-4720F/XEG
SCX-4520/XEG
SCX-4720F/XEP
SCX-4520/XEP
SCX-4720F/XET
SCX-4520/XET
SCX-4720F/XEU
SCX-4520/XEU
SCX-4720F/XIL
SCX-4520/XIL
SCX-4720F/XSG
SCX-4520/XSG
SCX-4720F/XEV
SCX-4520/XEV
SCX-4720F/XSA
SCX-4520/XSA
SCX-4720F/XIP
Buyer-Model Code
Appendix (Parts code)
JC96-03184A
-
JC96-03184A
JC96-03181A
JC96-03184B
JC96-03181B
JC96-03184C
JC96-03181C
JC96-03184D
JC96-03181D
JC96-03184J
JC96-03181J
JC96-03184E
JC96-03181E
JC96-03184A
JC96-03181A
JC96-03184F
JC96-03181F
JC96-03181A
JC96-03184G
JC96-03181G
ELA HOU-SCAN
JC96-03174A
-
JC96-03174A
JC96-03183A
JC96-03174B
JC96-03183B
JC96-03174C
JC96-03183C
JC96-03174D
JC96-03183D
JC96-03174J
JC96-03183J
JC96-03174E
JC96-03183E
JC96-03174A
JC96-03183A
JC96-03174F
JC96-03183F
JC96-03183A
JC96-03174G
JC96-03183G
ELA HOU-OPE
JC92-01599A
-
JC92-01599A
-
JC92-01599A
JC92-01599B
JC92-01599B
JC92-01599B
JC92-01599B
JC92-01599B
JC92-01599B
JC92-01599A
PBA SUB-LIU
Update: 9/10/04
ELECTRONICS
This service manual is also provided on the web,
the ITSELF system Samsung Electronics Co., Ltd.
http://itself.sec.samsung.co.kr
© Samsung Electronics Co.,Ltd. Oct. 2005
Printed in Korea.
VERSION NO. : 1.00
CODE : JC-0154I

DIGITAL LASER MFP

Transcription

Similar documents

88. Exploded Views and Parts List

88. Exploded Views and Parts List (SCX-4720F/XAX)

explodedview_slm2070fw_xaa

7. Exploded Views and Parts List(SCX

88. Exploded Views and Parts List