AP Industries

ENCAN PUBLIC
Woodworking Equipment, Former Assets of A. P. Industries Inc.
Équipement pour le travail du bois, anciens actifs de Les Industries A. P. inc.
As Awarded by Raymond Chabot Inc. (Trustee)
Tel qu’Adjugé par Raymond Chabot Inc. (syndic de l’actif)
Tuesday, December 15, 2015 @ 10:00 AM (EST)
Mardi 15 Décembre 2015 À 10:00 A.M. (EST)
346, rue Saint-Joseph à Laurier-Station, QC Canada G0S 1N0
Complete Dispersal of Equipment and
Inventory from a 228,000 sq. ft. Furniture
Manufacturing Facility
Vente de la totalité des équipements et de
l’inventaire situé dans une Usine de fabrication de
meubles de 228.000 pieds carrés
Inspection: Monday, December 14, 2015,
9:00 AM to 4:00 PM EST
Inspection: Lundi, 14 Décembre, 2015,
09h00-à-16:00 EST
www.asset-sales.ca · (902) 852-5331
PRINTED IN CANADA
4310 Prospect Road
Bayside, NS
Canada B3Z 1L5
TUESDAY, DECEMBER 15, 2015 @ 10:00 AM (EST )
Holzma HPP 230/38/38 New in 2008
Bending Presses with Rosenquist 30 KVA Generator
INVENTORY
• Timesavers Model 325-B-3HD, Serial no. 8618, Contact Drum 30
Hp, Contact Drum 20 Hp, Platen 20 Hp, 25” x 103” Belts,
5 Hp Variable Speed Feed., Holddown Shoes.
Large Quantity of furniture hardware including drawer slides,
hinges, drawer pulls, etc..
• Ekstrom Carlson Model 112A Double Sided Oscillating Edge
Sander, Serial no. 68-667, Belt Size: 8” x 162”, Tables: 11” x 60”,
End Table, 10” dia. Rubber Covered Drive Pulley,
Platens: 9” x 58”, Motor: 10HP, 550V.
Large Quantity of raw materials including particle board, plywood
and hardwood
EQUIPMENT
SANDING EQUIPMENT
• Nash Model 85 Chair Back Sander, Serial no. 314080
• DMC Unisand Model USK 1350 M3 Four Head Wide Belt
Sander, New in 2006, Serial no. SA/005404, 4770 Kg, 600V,
Capacity 53” Wide, First head: Crossbelt with Chevron and
Segmented Pad, Second Head: Steel Drum, Third Head:
Segmented Platen, Fourth Head: Segmented Platen, 52” x 103”
Belts, Feed Motor: 4 Kw, 3 Ph, 400V, Variable Speed Inverter,
Vacuum Bed.
• Progress Sander Buffer, 2- 9” Long Spindles, 8” Wide G & P
Brush Heads currently Mounted.
• Butfering Model Optimat 5BC 311 RCE, 3 Head Wide Belt
Sander, New in 2002, Serial no. 77798, Capacity 53” wide, First
Head Steel Contact Drum, Second Head Combination Head w/
Segmented Pad, Third Head Segmented Platen, Vacuum Bed,
Variable Speed Feed.
• Progress Sander Buffer, 2- 9” Long Arbors, Currently w/ 2- 8”
Wide G & P Brush Heads, 2 Hp Belt Drive.
• Heesemann Model MFA8 Four Head Wide Belt Sander,
Serial no. 200002091, New in 2000, Capacity 53” Wide, First
Head Steel Drum, Second Head Cross Belt Segmented with
Chevron Belt, Third Head Electronic Segmented Pad, Fourth Head
Electronis Segment Pad, Feed Motor: 3.6 Kw, Vacuum Bed.
MACHINING CENTERS
• Timesavers Model 25-3HD, Three Head 25” Wide Belt Sander,
Serial no. 7445, Contact Drum: 30 Hp, 11” dia. Drum, Contact
Drum: 20 Hp, 11” dia. Drum, Platen: 20 Hp, 25” x 103” Belts.
• King Canada Belt Disc Sander, 6” x 48” Belt and 9” Disc, Model
KC-7601, New in 2008, 1 HP, 1 Ph.
• Progress Sander Buffer, 2- 9” Long Arbors, Currently w/ 2- 8”
Wide G & P Brush Heads, 2 Hp Belt Drive.
• Custom Made Spindle Sander, Tilting, 1-1/4” dia x 8” Long,
Approx 1 Hp, 67” x 46” Table.
• Biesse Model Rover 20 CNC Machining Center, Serial no. 14105,
New in 2001, Working Capacity Approximately 3’ x 9’, 8 Rails with
Pods, ISO Tool Holders, One 7KW Router Motor, 4 Position Tool
Changer on left end, 4 Position Ride Along Tool Changer, 5 Vertical
Drills in “Y” axis, 5 Vertical Drills in “X” axis, Two (2) Double Sided
Horizontal Drill in “X” axis, One (1) Double Sided Horizontal Drill in
“Y” axis, 3 Kw Becker Vacuum Pump.
I N S P E C T I O N : M O N D AY, D E C E M B E R 14 , 2015, 9: 0 0 A M T O 4 : 0 0 P M E S T
I N S P E C T I O N : L U N D I , 14 D É C E M B R E , 2015, 0 9H 0 0 - À -16: 0 0 E S T
TUESDAY, DECEMBER 15, 2015 @ 10:00 AM (EST )
Holzma HPL 33/X/38/16 Rear Load Panel Saw
• Biesse Model Rover 20 CNC Machining Center, Serial no. 02815,
New in 2000, Working Capacity Approximately 3’ x 9’, 6 Rails with
Pods, ISO Tool Holders, One 7KW Router Motor, 4 Position Tool
Changer on left end, 4 Position Ride Along Tool Changer, 5 Vertical
Drills in “Y” axis, 5 Vertical Drills in “X” axis, Two (2) Double Sided
Horizontal Drill in “X” axis, One (1) Double Sided Horizontal Drill in
“Y” axis, 3 Kw Becker Vacuum Pump.
• Weeke Model Optimat BP145 CNC Machining Center,
Serial no. 0-250-08-1064, New in 2000, 200/600V, HSK Tool
Holders, Eight (8) Position Tool Changer, Two (2) Router Motors
(one w/ “C” Axis), 12 Vertical Drills in “X” axis, 10 Vertical Drills in
“Y” axis, Two(2) Double Sided Horizontal Drills in “X” axis, One (1)
Double Sided Horizontal Drill in “Y” axis, 8 Rails with Pods, Working
Capacity Approximately 50” x 14’, Becker 3Kw Vacuum Pump.
• Weeke Model Optimat BP-140 CNC Machining Center,
Serial no. 0-250-08-1297, New in 2000, 8 Rails with pods, HSK
Tool Holders, Eight (8) Position Tool Changer, Working Capacity
Approximately 50” x 14’, Two (2) Double Sided Horizontal Drills in
“X” axis, One (1) Double Sided Horizontal Drill “Y” axis, 11 Vertical
Drills in “X” axis, 10 Drills in “Y” axis, Becker Vacuum Pump 3 KW.
• Weeke Model BP120 Machining Center,
Serial no. 0-250-05-2405, 1997, Eight (8) Position Tool Changer,
Grooving Saw, 11 Vertical Drills in “Y” axis, 8 Vertical Drills in “X”
axis, One (1) Four Side Horizontal Drill Unit, 8 Rails w/Pods, Working
Capacity Approximately 3’ x 12’, Becker Vacuum Pump 3/5.6 KW.
• Weeke Model BP12/W/Optimal CNC Machining Center, New in
1997, Serial no. 0-250-05-2279, Working Capacity Approximately
3’ x 9’, 6 Rails with Pods, ISO Tool Holders, 6 Position Tool Changer
Right Side, 5 Vertical Drills in “Y” axis, 4 Vertical Drills in “X” axis,
One 4 Way Horizontal Drill Head, 3KW Becker Vacuum Pump.
DMC Unisand USK 1350 M3 New in 2006
• Weeke Model BP12/W/Optimat CNC Machining Center,
Serial no. 0-250-05-2039, New in 1997, 8 Rails w/Pad, 2 Router
Heads: 1- 7.5 Kw, 1- 5.5 Hp, 7 Vertical Drills in “Y” axis, 12 Vertical
Drills in “X” axis, Double Side two Spindle Horizontal Drill Block
in “X” axis, Single Side One Spindle Hori in “Y” axis, ISO 30 Tool
Holders, Becker Vacuum Pump 3 KW.
• Weeke Model Optimat BP150 CNC Machining Center,
Serial no. 0-250-08-0734, New in 1998, 8 Rails w/Pads, 2 Router
Heads, 1w/”C” Axis, 15 Vertical Drills in “X” axis, 15 Vertical Drills
in “Y” axis, 2 Double Sided Horizontal Drills in “X” axis, 1 Double
Sided Horizontal Drill in “Y” axis, 8 Position Tool Changer, Capacity
14’ x 50”, Becker Pump 3KW (Note: This machine has several
electronic components removed and sitting on a work bench.
Buyers should inspect prior to bidding)
PANEL SAWS
• Holzma Model HPP 230/38/38 CNC Panel Saw,
Serial no. 0-341-07-7650, New in 2008, Front Load Panel Saw,
Cutting Capacity 12’ x 12’, Transformer provide for 600V to 230
Power, Machine is set up for 230 Volt power, Main Saw Motor:
7.5KW (10HP), Scoring Saw Motor 1KW, Three (3) Air Floatation
Tables, 6 Grippers.
• Holzma Model HPL 33/X/38/16 Rear Load Panel Saw, Serial no.
0-240-15-1062, 2000, 12’ Ripping Capacity, Loads from the back
on either side, 9 Grippers, 600mm Dia. Blade, Saw Motor: 43 Kw,
4 Air Floater Tables., New in 2000.
EDGE BANDERS
• Brandt Model KDN210 Edgebander, Serial no. 0-261-20-1301,
New in 2008, Strip and coil feed, 3mm Guillotine, 3 Roll Pressure
unit, End Trim, Top & Bottom Trim Tilting, Top & Bottom Buffing.
I N S P E C T I O N : M O N D AY, D E C E M B E R 14 , 2015, 9: 0 0 A M T O 4 : 0 0 P M E S T
I N S P E C T I O N : L U N D I , 14 D É C E M B R E , 2015, 0 9H 0 0 - À -16: 0 0 E S T
TUESDAY, DECEMBER 15, 2015 @ 10:00 AM (EST )
Butfering Optimat 5BC 311 RCE
Heesemann MFA8
(1 of 2) Biesse Rover 20
(1 of 2) Weeke BP12
Homag KL 74/A26
Weinig P23E Five Head Moulder
• Brandt Model Optimat KD77-C Edge Bander,
Serial no. 0-261-02-7071, New in 1998, Coil Feed, 3 Roll Pressure
section, End Trim with two motors, Top & Bottom Trim, Corner
Rounding, Scraping, Buffing, Variable Speed Feed.
• Doucet Model BT-36-60-T6-36-264G Return Conveyor,
Serial no. 98-12-211, Receiving Table: 36” Wide x 60” Long,
Return Conveyor: 36” Wide x 264” Long, 8 Transfer Belts.
• Homag Model KL 74/A26 Edge Bander, New in 1997,
Serial no. 0-200-08-2939, Magazine Feed and Strip Feed, 7 Roll
Pressure Section, Granular Glue, End Trim, Top & Bottom Trim,
Top and Bottom finish trim, Variable Speed Feed.
• Unknown Return Conveyor, Receiving Table: 76” x 52”
w/ Three (3) - 24” Wide Plastic Chains, Feeding onto 40” x 75”
Roll Conveyor then to 22” x 17” Powered Roll Conveyor.
MOULDERS
• SCM Model P230S, 7 Head Feed Through Moulder,
Serial no. 84001959, 2 Meter Infeed Table, Rolls in Fence to
assist w/ Hopper Feed, Head Configuration: Bottom 6.6KW,
Right Side 13KW, Left Side 13KW, Top 13KW, Top 13KW, Bottom
13KW, Universal 13KW, 9” x 5” Capacity, Variable Speed Feed,
40mm Spindles, 2nd Top Head has Outboard Bearing, Short
Stock Feeding Attachment.
• Zimac Hopper Feed Unit, Serial no. 84.0770, 1 Hp Motor,
2 Feed Rolls.
• Weinig Model P23E Five Head Feed Through Moulder, Serial
no. 85724, New in 1998, 2 Meter Infeed Table, Head Configuration
Bottom- 7.5KW Motor, Right/Left side - 11KW motor, Top - 11KW
Motor, Bottom - 7.5KW Motor, ATS Set Up System, Feed Motor
3KW Variable Speed, 40mm Spindles, Bed Lubrication with
Wax-o-Lite Pump, Ziwo Model CL11 Random Length Hopper
Feeder, Serial no. 86-0880, 1HP, 575 Volt.
BENDING PRESSES
• Two (2) Hi-Frequency Plywood Bending Presses,
Approx. 40” x 96” x 36” High, Equipped with a Rosenquist Model
G-30, 30 KVA High Frequency Generator, serial no. 11981142239,
575V, 68 Amp Input.
• Two (2) Makno Hi- Frequency Plywood Bending Presses with
Generator
SAWS
• Barr-Mullin Model Compu-Rip Gang Rip Optimizing System,
Serial no. 009897, New in 1998, 5 Laser Lights mounted on
Overhead Beam to Show Cut Pattern, Infeed Chain Deck 15’ Long
x 12’ Wide w/ 5 Chains, Pin Stop Hold Boards until Board Dealer
Released to Measuring Station Fence, Board is Release to another
I N S P E C T I O N : M O N D AY, D E C E M B E R 14 , 2015, 9: 0 0 A M T O 4 : 0 0 P M E S T
I N S P E C T I O N : L U N D I , 14 D É C E M B R E , 2015, 0 9H 0 0 - À -16: 0 0 E S T
TUESDAY, DECEMBER 15, 2015 @ 10:00 AM (EST )
Weeke Optimat BP145
Weeke Optimat BP-140
Weeke BP120
Mereen Johnson 419DCS
Brandt KDN210 Edgebander New in 2008
Brandt Optimat KD77-C
Pin Stop, then a Board Dealer Sends to Infeed, Canted Roll Case
w/ moving Fence controlled by Computer, Pinch Roll Moves
Board into Gang Rip.
• Mereen Johnson Model 419DCS Short Stock Gang Rip Saw,
Serial no. MJ3874, Width Capacity 19”, Pneumatic Press Rolls,
Outboard Bearing, 3-1/8” Diameter Bore Saw Blades, Two(2) Saw
Sleeves w/Spacers, Arbor Motor: 50 Hp, 3 Ph, Feed Motor: 3 Hp,
3 Ph, 330/575 Volt, Feed Speeds 30-150 FPM.
• Gang Rip Outfeed Chain Deck: 12’ Wide x 8’ Long Chains.
• Silver Model SJS-12 Double Miter Saw, Serial no. P928, 2001,
2- 1 Hp Motors, 12” dia. Blades, Infeed Table: 6” x 48”,
Outfeed: 6” x 60” w/ Stop Bar and 1 Stop.
• Wilson 30” Bandsaw, Table: 30” x 36” Tilting, Throat Clearance
28”, Manual Foot Brake.
• Silver Model SYFC-18 Up Cut Saw, Serial no. 2002V706, 2002,
7,5 HP Motor, 575V, Left Hand Up Cut Saw, 18” dia. Blade, 2”
x 12” Cutting Capacity, Homemade Tables: Infeed: 18” x 84”,
Outfeed: 18” x 84” with 3 Flip Stops.
• Poitras Model 355, 24” Bandsaw, Serial no. J.76.24.90
Table: 23-1/2” x 25-1/2”, Throat 24”, 2 HP, 3 Ph, 575V.
• General Model V-154 Radial Arm Saw, Serial no. G12958,
14” dia. Blade, 44” Arm, 21” Crosscut Capacity, 5 Hp, 3 Ph, 600V,
Blade tilts and Arm Swivels, Wooden Table: 26-1/2” x 96”, Kreg
Fence System w/ 3 Flip Stops.
• General Model 50-500 Table Saw, Serial no. 50189399,
5 Hp Motor, New in 1999, General T Saw Fence System 50”,
Main Table: 38” x 42”, Auxiliary Table: 38” x 31” Wood,
Overhead Guard.
• Mattison Model 404 Straight Line Rip Saw, Serial no. 22261,
Motor 15HP, 3 Ph, 550V, 4 Speed Feed, Equipped w/Panel Lay Up
Gauge and Table, Infeed Fence and 1 Stop.
• Poitras 10” Table Saw, Serial no. N 6 2.12.235, 30” x 30” Table
w/ Holz-Her 3 Roll Feeder, 8 Speed.
• Holytek Model HCS-14RH Up-Cut Saw, Serial no. 20070470,
New in 2007, 5 HP Motor, 14” Blades, Tiger Stop 6’ Capacity
w/Key Pad, Infeed Table 16” Wide x 60”, Outfeed Table 16”
Wide x 72”.
• Wadkin Radial Arm Saw, 14” dia. Blade, Crosscut Capacity 15”,
Motor: 3 KW (4.5 HP), 3 Ph, 550V, Pneumatic Cylinder Advances
Saw, Foot Pedal Activated, Table to Right of Saw: 16” x 48”, Table
to Left of Saw: 16” x 85” with Stop Bar and 8 Stops.
I N S P E C T I O N : M O N D AY, D E C E M B E R 14 , 2015, 9: 0 0 A M T O 4 : 0 0 P M E S T
I N S P E C T I O N : L U N D I , 14 D É C E M B R E , 2015, 0 9H 0 0 - À -16: 0 0 E S T
TUESDAY, DECEMBER 15, 2015 @ 10:00 AM (EST )
Koch Sprint
Koch Sprint-PTP
Northfield 240 with Carbide Insert Cutterheads
Koch Sprint-PIP
JKO HM-300 12” Hauncher
Phoenix PHP-2208
• Galt Canadian Tatey Model 1600/S Radial Arm Saw, 3 Hp, 3 Ph,
14” dia. Blade, 8’ Fence w/ One Stop.
• Oliver Model 88-D Sliding Table Saw, Serial no. 98083, Tilting
Arbor, Precision Fence, 7.5 Hp, 3 Ph, 550V, Overhead Guard.
GLUE & DOWELL MACHINES
• Koch Double End Bore, Glue and Dowel Machine, Each Side:
10 Spindle Boring Head 32mm on Centers, one Dowel Insertion
Unit w/ Vibrating Hopper, One Two Spindle Boring Head in back
that rotates for horizontal or Vertical Arrangement of Drills, 32mm
Centers, One Vertical Drill w/ ½” Jacobs Chuck, Approx 80”
Opening, Computer Aided Set Up for Opening, Position of Rear
Drill Unit & Vertical Drill Unit.
• Koch Model Sprint, Serial no. 9410/5113, New in 1994, 21
Spindles Horizontal Bore on 32mm Centers, 8 Glue & Dowel
Injectors Adjustable, 4 Vertical Pneumatic Holddown Clamps,
Table: 43” x 13”.
• Tiger Stop, 72” Bar w/ Stop Fence, Control Panel, Table: 15” x 72”.
• Koch Model Sprint-PTP CNC Horizontal Bore/Glue/Dowel, Serial
no. 9912/5900, New in 1999, Table: 48” x 18”, 4 Pneumatic
Holddown Clamps, Vibrating Hopper for Dowel Pins, Equipped
with Pizzi Model 9001 Glue Tank, Serial no 0231, New in 2003.
PLANERS
• Buss Model 66 Single Side Planer, Size: 42” x 8”, Serial no.
6823, Motor: 40HP Belt Drive, Equipped w/ Oliver Itch Type
Carbide Insert Cutterhead, Supplied w/ Grinder.
• Northfield Model 240 Double Sided Straight-O-Planer, Capacity
24” x 6”, Equipped w/ 6 Row Insert Carbide Cutterheads Bottom
Head Motor 30HP, Top Head Motor 40HP, Feed Motor 5HP, Feed
Speeds 25-100 FPM.
• Planer Outfeed Belt Conveyor, 36” Wide x 10’ Long w/ Spring
Loaded Top Roll at End. Approx 2 Hp. Motor w/ Reeves Drive to
Vary Speed.
BORING MACHINES
• Castle Model TSM-35 Pocket Boring Machine, Serial no. 60516,
1.5HP router motor for slot, air drill motor, foot pedal activated,
Homemade Infeed & Outfeed Tables: 11” x 44” Each w/ Wooden
Stop Bars, 5 Stops each Side.
• Castle Model TSM-35 Pocket Boring Machine, Serial no. 60315,
16” x 18” Table, 1 Vertical Pneumatic Hold down, 1.5HP router
motor for slot, air drill motor, foot pedal activated.
• Koch Model Sprint-PIP CNC Horizontal Boring Machine,
Serial no. 9806/5945, New in 1998, Four (4) Spindle boring head
32mm centers, Table: 92” x 18”, 8 Pneumatic Holddown Clamps.
I N S P E C T I O N : M O N D AY, D E C E M B E R 14 , 2015, 9: 0 0 A M T O 4 : 0 0 P M E S T
I N S P E C T I O N : L U N D I , 14 D É C E M B R E , 2015, 0 9H 0 0 - À -16: 0 0 E S T
TUESDAY, DECEMBER 15, 2015 @ 10:00 AM (EST )
TENONERS
• Fletcher Model FM-200D Double End Tenoner/Foiler,
Serial no. 89200D-7, Capacity 72” Opening x 48” Load Space,
Padded Chains 1-1/2” Wide, Flip up Dogs on every Link 5” apart,
Caterpillar Type HoldDown Pads, Stations: Trim Saws 10 Hp,
Tilting Cope: 15 Hp w/ Servo Set Up, Tilting Cope: 15 Hp with
Servo Set up, Groover Saw: 2 Hp Tilting with Servo set up, Open
Station, Long Belt Sander Approx 2 Hp, Tilting, Foil Applicator
Station, Horizontal Arbor: 10 Hp, Left Side Only.
• Silver Model SYRT-115 Round End Tenoner, Serial no. 2203008,
New in 2002, Two Tables each 12” x 15” w/ 2” High Fence and
Pneumatic Holddown Clamps, Tables Tilt.
MISC. WOODWORKING EQUIPMENT
• JKO Model HM-300 Hauncher, Approx 10 Hp Motors, 12” Wide
Arbor, 2 Pneumatic Hold Down Clamps, Serial no. 2598.
• Silver Model SYOM-120 Double Sided Slot Mortiser,
Serial no. 2203007, New in 2002, 2 HP Spindle Motor, 1/2 HP Osc
Motor, Two Tables: 12” x 17.5” each w/ Pneumatic Holddown Clamps.
• Holytek Model SS-512 MS Single Spindle Shaper,
Serial no. 0211056, 2002, Motor 7.5 HP, 575V Sliding Table
Shaper with Homemade Attachment that can be removed,
1-1/2” dia. Spindle.
• Poitras 8” Jointer, Serial no. C77 8 1773, Infeed Table: 9.5” x
29”, Outfeed Table: 9.5” x 29” with 1” Rabbeting Ledge, Fence:
4-1/2” x 32” Tilting.
• Delta 16-1/2” Drill Press, 16 Speed, Model 17-965C,
Serial no. W0020, ¾ Hp, 1 Ph, 110V, 1- 16mm Jacobs Type
Chuck, 14” x 14” Tilting Table, 6’ Stop Bar w/ 2 Stops.
• Holytek Model FS5032 Pneumatic Drill Unit,
Serial no. 026010, New in 2002, 1 HP Motor, Mounted to
33” x 78” Work Table, 72” Stop Bar/Fence w/ 6 Stops,
Universal Mount to Adjustable Boring Head In/Out,
Up/Down Angle.
• General Model 75-150ml, 13” Drill Press, ½ Hp, 1 Ph,
110/220V, ½” Jacobs Chuck, 12” dia. Table Tilting, 11” x 18”
Wooden Table Mounted.
• Desoutter Pneumatic Drill w/ 1 Hp Motor, ½” Jacobs Chuck.
PACKAGING
• Phoenix Packaging Machinery Model PHP-2208 Shrink
Wrapper, Serial no. 0103879, 115V, 4’ x 4’ Rotating Table,
72” High Capacity, 20” Wide Roll.
DUST COLLECTOR
• Mfg. Unk. Dust Collector w/ 1 - 25 hp fan, 1 -20 hp fan and
Transfo Model VR1224, 3 HP Airlock.
SHARPENING / GRINDING EQUIPMENT
• Onsrud Model WT2 1284 H Linear Profiler, S/N- 797469-01,
2 Spindles, 8” High w/ Outboard Bearings, 84” Stroke x 19”
Wide Table.
• 2000 Vollmer Model Unimat “S” Saw Blade Sharpener,
s/n 1120, c/w Vollmer PMC Control, 440V/60/3PH w/ Step
Down Transformer.
• General Model 40-500M3 Tilting Spindle Shaper w/Sliding
Table, Serial no. 40073901, New in 2001, Motor 7.5HP, Spindle
Size 1-1/4” Diameter x 5” Under the Nut, Main Table: 22” x 40”
, Sliding Table: 10” x 40”, 3 Roll Feeder, Model AP/34, Serial no.
20025816, New in 2002, 575V, 1 HP, 3 Ph, 575V, 4 Speed w/
Universal Stand.
• 1981 Weinig Model R-930 Sharpener, s/n 002/1111
• Lancaster Model 1410-HF Two Way Frame Clamp,
Serial no. 1410-HF-10, 84” x 48” Capacity, 2- 6” dia. X 3” Stroke
Cylinders on left, 2- 6” dia. X 3” Stroke Cylinders on Top Jaw,
Jaws: 7-1/2” x 3” High.
• AWork Rite Model 4000 Wood Welder, 115V, Serial no. 4K629,
8/29/08.
• Holytek Model FS-030 Pneumatic Drill Head mounted to a
Drill Press Base, Serial no. 9101001, New in 2004, 1 HP, 575V,
Equipped w/ ½” Jacobs Chuck, Pneumatic Foot Pedal, Stop Bar
w/Two Stops.
• Steel City 17” Drill Press, Model 20520, Serial no. XL1808,
Single Phase, 110V, Main Table: 14” x 14” Tilting.
• Jones & Shipman Tool & Cutter Grinder, s/n 1438 w/ Tilting
Permanent Magnetic Chuck.
• Dependable Model 152A Tool & Cutter Grinder,
s/n A2894.
ROLLING STOCK
• 2002 Toyota Model 7FGU35, s/n 60676, LPG Forklift w/ 7,000
lb. Cap., Three Stage Mast w/ 187” Lift, Side Shift, Showing
13,300 Hours.
• 1996 Nissan Model KUGH02-900095, s/n KUGHO2-90009,
LPG Forklift w/ 6,000 lb. Cap., Three Stage Mast w/ 187” Lift,
Side Shift.
• 2011 Dodge Durango Flexfuel AWD,
s/n 1D4RE2GG9BC663028 W/ 3.6L V-6 Engine, AT,
Showing 142,000 km.
I N S P E C T I O N : M O N D AY, D E C E M B E R 14 , 2015, 9: 0 0 A M T O 4 : 0 0 P M E S T
I N S P E C T I O N : L U N D I , 14 D É C E M B R E , 2015, 0 9H 0 0 - À -16: 0 0 E S T
AUCTION–ENCAN PUBLIC
TUESDAY, DECEMBER 15, 2015 @ 10:00 AM (EST )
2000 Vollmer
Toyota 7FGU35
2011 Dodge Durango
Dust Collector
A 15% Buyer’s premium will be charged on all onsite purchases and an 18% Buyer’s premium will
be charged on all online purchases.
Une prime de 15% sera facturée à l’Acheteur sur tous les achats effectués sur place .La prime sera
de 18% pour tous les achats effectués en ligne.
ONLINE BIDDING AVAILABLE VIA
Enchères en ligne via:
Payment will be accepted via Bank Draft, Certified Cheque, Wire Transfer or Credit Cards (Visa, Mastercard or American
Express) to a Maximum of $1,000.
Les paiements peuvent être faits par traites bancaires, chèques certifiés, transferts de fonds ou cartes de crédit
(Visa, MasterCard ou American Express) pour des sommes n’excédant pas 1 000 CAD.
NO CHECK-OUT WILL BE ALLOWED ON AUCTION DAY! CHECK OUT WILL BE OPEN FROM
8 :00 AM TO 5 :00 PM WEEKDAYS, and, SATURDAYS BY APPOINTMENT ONLY!
AUCUNE SORTIE DE MARCHANDISE LE JOUR DE L’ENCAN. La prise de possession des biens achetés est possible du
lundi au vendredi entre 8h et 17h et le samedi sur rendez-vous seulement.
ALL EQUIPMENT AND INVENTORY ITEMS MUST BE REMOVED BY WEDNESDAY, DECEMBER 30, 2015, NO EXCEPTIONS!
LES AUTRES ITEMS DOIVENT ÊTRE RÉCUPÉRÉS AVANT LE 30 DÉCEMBRE 2015.
This auction is being
conducted in association with
Daniel Paul-Hus, Auctioneer
DANIEL
PAUL-HUS
ENCANTEUR BILINGUE
635, Papineau
Saint-Hyacinthe (Québec)
J2S 7J5
tél : 450 773 5660
www.paul-hus.com