Catalog: Swan Secure Fasteners (C-SSTSWAN09)

Transcription

Distributed by: BEST MATERIALS LLC
Ph: 800-474-7570, 602-272-8128 Fax: 602-272-8014
www.BestMaterials.com Email: [email protected]
SWAN SECURE
FASTENERS
C-SSTSWAN09
Simpson Strong-Tie ® Swan Secure Fasteners
TABLE OF CONTENTS
NAILS
Hand-Drive Nails
Box, Ring-Shank Nails ......................................................................................................... 56
Cedar and Redwood Decking Nails ...................................................................................... 14
Fiber-Cement Siding Portland™ Nails ................................................................................. 34
Finishing Nails ...................................................................................................................... 65
Gutter Spikes ........................................................................................................................ 48
Marine Sea-Cure™ Nails ...................................................................................................... 84
Post and Beam, Ring Shank Nails ....................................................................................... 56
Preservative-Treated Lumber Nails ...................................................................................... 14
Roofing / Slating, Aluminum Nails ...................................................................................... 45
Roofing / Slating, Copper Nails ........................................................................................... 44
Roofing / Slating, Stainless-Steel Nails .............................................................................. 45
Roofing Nails, Washered ...................................................................................................... 46
Shake and Shingle Nails ................................................................................................. 32, 46
Siding Nails, Painted ............................................................................................................ 33
Siding Nails, Pyramid Head ................................................................................................. 34
Structural Connector, Smooth-Shank Nails ........................................................................ 57
Tile/Slate Nails, Copper ........................................................................................................ 47
Tile/Slate Nails, Stainless Steel ........................................................................................... 48
Un-Common™ Common Ring Shank and Smooth Shank Nails .................................. 55, 77
Wood Siding Nails ................................................................................................................ 32
Bostitch® – Type Angle Finishing Nails ................................................................................ 66
Inserted Plastic-Coil 15° Nails ............................................................................................. 37
Paper Tape 31°, Structural Connector, Ring Shank Nails ................................................... 60
Paper Tape 31-34°, Clipped Head, Ring-Shank Nails ................................................... 17, 61
Paper Tape 31-34°, Full-Round Head, Ring-Shank Nails .................................................... 17
Paslode ® – Type Angle Finishing Nails ................................................................................. 66
Paslode ® – Type Straight Finishing Nails ............................................................................. 67
Plastic Coil 15° Nails ............................................................................................................ 36
Plastic Strip 20-22°, Casing Head, Ring-Shank Nails .................................................. 16, 59
Plastic Strip 20-22°, Full Round Head, Ring-Shank Nails ........................................... 15, 57
Plastic Strip 20-22°, Full Round Head, Screw-Shank Nails ......................................... 16, 58
Plastic Strip 20-22°, Full Round Head, Smooth-Shank Nails ............................................. 59
Plastic Strip 31-34°, Full Round Head, Ring-Shank Nails ............................................ 17, 61
Senco ® – Type Angle Finishing Nails .................................................................................... 66
Straight Brads ...................................................................................................................... 67
Wire Coil 15°, Roofing Nails ................................................................................................. 49
Wire Coil 15°, Painted Nails ........................................................................................... 36, 68
Wire Coil 15°, Ring-Shank Nails .............................................................................. 18, 35, 60
Wire Coil, Ring Shank, Fiber-Cement-Siding Nails ............................................................. 35
Wire Weld 28°, Clipped Head, Ring-Shank Nails .......................................................... 18, 59
SCREWS
4
Hand-Drive Screws
Bugle Head, 6-Lobe-Drive Swaneze™ Screws ................................................................... 21
Bugle Head, Square-Drive Swaneze™ Screws ................................................................... 20
Bugle Head, Square-Drive Swaneze™ Boardwalk™ Screws .............................................. 21
Composite-Decking Composi-Lok™ Screws, Coated, Square Drive ................................. 26
Composite-Decking Dexxter™ Screws, 6-Lobe Drive .................................................. 22, 74
Composite-Decking Dexxter™ Screws, Painted Trim Head, 6-Lobe Drive ........................ 27
Fiber-Cement FY-CEM™ Screws for Wood ......................................................................... 37
Flat Head, 6-Lobe-Drive Woodpeckers™ Screws ............................................................... 23
C-SSTSWAN09 © 2009 SIMPSON STRONG-TIE COMPANY INC.
Collated Nails
TABLE OF CONTENTS
SCREWS
(cont.)
MISCELLANEOUS
FASTENERS
SPECIALTY
ITEMS
Gutter Screws ....................................................................................................................... 53
Hex-Washer-Head Strong-Drive ® Screw ............................................................................. 63
Hex-Washer-Head Timber Tamers™ Screws ...................................................................... 62
K-Lath Modified Truss Head, Self-Drilling Screws ....................................................... 40, 82
K-Lath Modified Truss Head, Wood Screws ....................................................................... 40
Marine Sharx™ Screws .................................................................................................. 74, 75
Painted Bugle Head, Square-Drive Swaneze™ Screws ....................................................... 25
Painted Trim Head, 6-Lobe-Drive Swaneze™ Screws ......................................................... 24
Painted Trim Head, 6-Lobe-Drive Woodpeckers™ Screws ................................................. 27
Painted Trim Head, Square-Drive Swaneze™ Screws ................................................... 24, 70
Pancake/Clip Self-Drilling Screws ....................................................................................... 53
Pancake/Clip Type A-Point Screws ..................................................................................... 53
Self Drilling, Bugle-Head Billy Goats™ Screws ................................................................... 79
Self Drilling, Flat-Head Billy Goats™ Screws with Wings .................................................. 80
Self Drilling, FY-CEM™ Fiber-Cement Billy Goats™ Screws for Metal-Studs .............. 38, 82
Self Drilling, Marutex Hex-Washer-Head Billy Goats™ Screws .......................................... 81
Self Drilling, Trim-Head Billy Goats™ Screws for Metal Studs ..................................... 38, 79
Self Drilling, Wafer-Head Billy Goats™ Screws with Wings ............................................... 80
Trim-Head, 6-Lobe-Drive Swaneze™ Screws ...................................................................... 19
Trim-Head, 6-Lobe-Drive Woodpeckers™ Screws ....................................................... 23, 69
Trim-Head, Coated, Square-Drive Screws ........................................................................... 25
Trim Head, Square-Drive Swaneze™ Screws .......................................................... 19, 69, 76
Trim-Head Swaneze™ Screws, Sealing Washer ................................................................ 77
Truss Head, Coarse Thread, Square-Drive Screws ............................................................. 76
Truss Head, Self-Drilling Roofing Screws ........................................................................... 52
Twin-Lead Threads, Hex-Washer-Head Screws (with and without washer) ................ 39, 52
Collated Staples
Similar to Bostitch® “BCS” Series Staples .............................................................. 42, 51, 71
Similar to Paslode ® “GS” Series Staples ................................................................ 41, 51, 71
Similar to Paslode ® “GSI” Series Staples ........................................................................... 42
Similar to Senco ® “C” Series Staples .................................................................................. 72
Similar to Senco ® “L” Series Staples ............................................................................ 50, 71
Similar to Senco ® “N” Series Staples ....................................................................... 41, 50, 72
Similar to Senco ® “P” Series Staples ............................................................................ 51, 72
EB-TY® Hidden Deck Fastening Systems ............................................................................ 28
Drill ‘n Drive™ Tool ............................................................................................................... 86
Fencing Nails ........................................................................................................................ 85
Fencing Staples .................................................................................................................... 85
Flooring Cleats, “L” Series ................................................................................................... 30
Flooring Cleats, “T” Series ................................................................................................... 30
Flooring Staples, Similar to Bostitch® ................................................................................. 30
Hog Rings ............................................................................................................................. 85
Marine Sea-Cure™ Nails ...................................................................................................... 84
Premium Driver Bits ............................................................................................................. 86
Storm-Panel Screw .............................................................................................................. 87
Wood Plugs (Ipê) ................................................................................................................. 87
5
DECKING
DECKING
Hand-Drive Nails
Cedar and Redwood ........................................................... 14
Preservative-Treated Lumber ............................................. 14
Collated Nails
Photo courtesy of California Redwood Association
Plastic Strip 20–22°, Stainless, Full Round, Ring Shank .... 15
Plastic Strip 20–22°, Bronze, Full Round, Ring Shank ........ 15
Plastic Strip 20–22°, Stainless, Full Round, Screw Shank .. 16
Plastic Strip 20–22°, Stainless, Casing Head, Ring Shank.. 16
Plastic Strip 31–34°, Stainless, Full Round, Ring Shank .....17
Paper Tape, 31–34°, Stainless, Clipped Head, Ring Shank ..17
Wire Coil 15°, Stainless, Ring Shank ................................. 18
Wire Weld 28°, Stainless, Ring Shank ............................... 18
Hand-Drive Screws
Trim Head, Square Drive Swaneze ™ ................................... 19
Trim Head, 6-Lobe Drive Swaneze ™ ................................... 19
Bugle Head, Square Drive Swaneze ™ ................................. 20
Bugle Head Swaneze ™ Boardwalks ™ .................................. 21
Bugle Head, 6-Lobe Drive Swaneze ™ ................................. 21
Composite Decking, 6-Lobe Drive Dexxter ™ ..................... 22
Flat Head, 6-Lobe Drive Woodpeckers ™ ............................ 23
Trim Head, 6-Lobe Drive Woodpeckers ™ ........................... 23
Hand-Drive Screws, Painted-Head
Trim Head, Square Drive Swaneze ™ ................................... 24
Trim Head, 6-Lobe Drive Swaneze ™ ................................... 24
Bugle Head, Square Drive Swaneze ™ ................................. 25
Standard Coated Trim Head, Square Drive ........................ 25
Composite Decking, Square Drive Composi-Lok ™............. 26
Trim Head, 6-Lobe Drive Woodpecker ™ ............................. 27
Composite Decking, Trim Head, 6-Lobe Drive Dexxter ™ ..... 27
EB-TY® Hidden Deck Fastening System
All Styles ............................................................................ 28
Flooring Cleats and Staples
“T” Shape Cleats ................................................................. 30
“L” Shape Cleats .................................................................. 30
Flooring Staples (similar to Bostitch ® ) .............................. 30
Ph: 800-474-7570, 602-272-8128 Fax: 602-272-8014
13
DECKING
Hand-Drive Nails
HAND-DRIVE NAILS | Cedar and Redwood
• Annular ring threads provide secure attachment of cedar, redwood and
other stable decking materials to deck joists and reduce nail head popping.
• Slender shanks permit nailing at board ends with reduced splitting.
• Small unobtrusive checker pattern heads blend with wood grain and diffract sunlight.
• Decking nails available pre-finished in tan, redwood and gray colors –
contact Simpson Strong-Tie for price and availability.
• Choose type 316 for seaside applications and superior corrosion resistance
• Bucket = 25 lbs.
Available in 3 colors
Tan
Redwood
Gray
See note below
304 and 316 Stainless Steel
Penny
Size
Length
Gauge
Shank
Diameter
Head
Diameter
Approx.
Count per lb.
8d1
2 1⁄2"
12
.109"
10d
3"
12
12d
3 1⁄4"
16d
3 1⁄2"
7
⁄32"
145
S8CRD25
S8CRD5
S8CRD1
S8CRDB
.109"
7
⁄32"
120
S10CRD25
S10CRD5
S10CRD1
S10CRDB
12
.109"
7
⁄32"
110
S12CRD25
S12CRD5
S12CRD1
S12CRDB
11
.120"
⁄4"
88
S16CRD25
S16CRD5
S16CRD1
S16CRDB
1 lb.
Item No.
Bucket
Item No.
1
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
Bucket
Item No.
Available
in 316 2
1. When ordering 8d nails in colors, insert the first letter of the color after the 5th character in the model number.
EXAMPLE: S8CRD5 becomes S8CRDT5 when ordering Tan. Contact Simpson Strong-Tie for details on other sizes.
2. For sizes available in 316 stainless steel (
), substitute the letter “T” as the first character of the item number.
HAND-DRIVE NAILS | Preservative-Treated Wood / ACQ
•
•
•
•
•
Annular ring threads provide greater pull-out resistance, reduce nail-head popping
Checkered flat head, diamond point
Larger shank diameter easily penetrates both green and seasoned preservative-treated pine
Ideal for decks and docks
Choose type 316 for seaside applications and superior corrosion resistance
Penny
Size
Length
Gauge
Shank
Diameter
Head
Diameter
Approx.
Count per lb.
8d
2 1⁄2"
11
.120"
8d
1
2 ⁄2 "
10
10d
3"
10d
9
⁄32"
115
S8PTD25
S8PTD5
S8PTD1
S8PTDB
.134"
9
⁄32"
94
S8HPTD25
S8HPTD5
S8HPTD1
S8HPTDB
10
.134"
9
⁄32"
79
S10PTD25
S10PTD5
S10PTD1
S10PTDB
3"
9
.148"
5
⁄16 "
67
S10HPTD25
S10HPTD5
S10HPTD1
S10HPTDB
12d
3 1⁄4"
9
.148"
5
⁄16 "
60
S12PTD25
S12PTD5
S12PTD1
S12PTDB
16d
1
3 ⁄2 "
9
.148"
5
⁄16 "
56
S16PTD25
S16PTD5
S16PTD1
S16PTDB
16d
3 1⁄2"
8
.165"
11
⁄32"
44
S16HPTD25
S16HPTD5
S16HPTD1
S16HPTDB
20d
4"
8
.165"
11
20d
4"
6
.203"
7
* For sizes available in 316 stainless steel (
All of our hand-driven nails can be
ordered passivated for a nominal
up-charge. Passivation is a light
acid bath that cleans the fastener of
surface contaminants and aids in
preventing premature corrosion.
5 lb.
Item No.
⁄32"
40
S20PTD25
S20PTD5
S20PTD1
S20PTDB
⁄16 "
25
S20HPTD25
S20HPTD5
S20HPTD1
S20HPTDB
!
14
25 lb.
Item No.
Available
in 316*
DECKING
Collated Nails
COLLATED NAILS | Plastic Strip 20–22°, Full Round Head, Ring Shank
•
•
•
•
•
20–22° collation angle
⁄32" diameter checker-patterned round head
Orange or clear glue on nails to further increase pull-out resistance
Silicon bronze offers resistance to stress corrosion cracking under nail heads
9
Length
Shank
Diameter
Box
Count
Item No.
2"
.113"
5000
S12A200CNB
2"
.113"
1000
S12A200CNJ
2"
.120"
5000
S11A200CNB
2"
.120"
1000
S11A200CNJ
1
2 ⁄4"
.148"
1000
S9A225CNJ
2 3⁄8"
.113"
5000
S12A237CNB
2 3⁄8"
.113"
1000
S12A237CNJ
2 1⁄2"
.120"
4000
S11A250CNB
2 1⁄2"
.120"
1000
S11A250CNJ
1
2 ⁄2"
.134"
4000
S10A250CNB
3"
.120"
4000
S11A300CNB
3"
.120"
1000
S11A300CNJ
3"
.134"
4000
S10A300CNB
3"
.134"
1000
S10A300CNJ
1
3 ⁄4"
.120"
4000
S11A325CNB
3 1⁄4"
.120"
1000
S11A325CNJ
1
3 ⁄4"
.134"
4000
S10A325CNB
3 1⁄4"
.134"
1000
S10A325CNJ
1
3 ⁄2"
.134"
4000
S10A350CNB
3 ⁄2"
.134"
1000
S10A350CNJ
1
of the item number.
Available
in 316*
—
—
), substitute the letter “T” as the first character
Silicon Bronze
Length
Shank
Diameter
Box
Count
Item No.
2 1⁄2"
.120"
4000
I11A250CNB
1
2 ⁄2"
.120"
1000
I11A250CNJ
3 1⁄4"
.120"
4000
I11A325CNB
3 1⁄4"
.120"
1000
I11A325CNJ
Compatible Pneumatic Tools – Collated 20–22° Plastic Strip
see following page >
15
DECKING
Collated Nails
COLLATED NAILS | Plastic Strip 20–22°, Full Round Head, Screw Shank
•
•
•
•
⁄32" diameter smooth round head
9
Length
Shank
Diameter
Box
Count
Item No.
2"
.113"
5000
S12S200CNB
2"
.113"
1000
S12S200CNJ
2 1⁄2"
.113"
4000
S12S250CNB
2 1⁄2"
.113"
1000
S12S250CNJ
3"
.120"
4000
S11S300CNB
3"
.120"
1000
S11S300CNJ
1
3 ⁄4"
.120"
4000
S11S325CNB
3 1⁄4"
.120"
1000
S11S325CNJ
1
3 ⁄2"
.134"
4000
S10S350CNB
3 1⁄2"
.134"
1000
S10S350CNJ
Available
in 316*
COLLATED NAILS | Plastic Strip 20–22°, Casing Head, Ring Shank
⁄4" diameter checker-patterned, countersunk casing head
Orange or clear glue on nails to enhance pull-out resistance
Available with painted heads – see below
1
•
•
•
•
304 Stainless Steel
Length
Shank
Diameter
Box
Count
Item No.
2 3⁄8"
.120"
1000
S11A237KDJ
3 ⁄4"
.134"
1000
S10A325KDJ
1
1. When ordering in colors, substitute the last three letters in the model number: KJB = Brown, KJG = Gray,
KJR = Redwood, KJS = Sienna; KJT = Tan. Example: a 2 3⁄8 " nail in Brown is model S11A237KJB.
Bostitch®
Dewalt ®
Duo-Fast ®
Fasco®
Hitachi®
Makita®
MAX®
Paslode®
Porter Cable®
Senco®
Stan-Tech®
16
RN90, RN95HN (up to .162"), N88RH (up to .162"), N88RH-2MCN, F21PL
D51845, D51844
CN350, SNP-83, NSP-350F
R5C-RHN20-90SS
NR83A (up to 31⁄4"), NR90AC2 (up to .162"), NR90AC, NR90AA2, NR83AG, NR90SSC
AN8300, AN922
SN890RH, SN90, GS683
5350/SRH20
FR350, FR350A, FR350MAG
FramePro 600FRH & FramePro 602 (up to 31⁄2"), FramePro 650FRH (21⁄4" to 31⁄2"),
FramePro 652 (up to 31⁄2"), FramePro 700XL FRH, FramePro 702XP (upto 31⁄2") &
FramePro 752XP (up to 31⁄2"), SN60, SN65C (up to .162")
SDN11, SDN11B-1
Brown
Gray
Redwood Sienna
Tan
DECKING
Collated Nails
• 31–34° collation angle
• 9⁄32" diameter checker-patterned round head
Length
Shank
Diameter
Box
Count
Item No.
2 3⁄8"
.113"
4000
S12A237B31
3
2 ⁄8 "
.113"
1000
S12A237P31
3"
.120"
4000
S11A300B31
3"
.120"
1000
S11A300P31
1
3 ⁄4"
.131"
4000
S10A325B31
3 1⁄4"
.131"
1000
S10A325P31
Available
in 316*
COLLATED NAILS | Paper Tape 31–34°, Clipped Head, Ring Shank
Length
Shank
Diameter
Box
Count
Item No.
2"
.113"
1000
S12A200T31
3
2 ⁄8"
.113"
1000
S12A237T31
3"
.120"
1000
S11A300T31
3 1⁄4"
.131"
1000
S10A325T31
3 1⁄2"
.131"
1000
S10A350T31
Available
in 316*
Compatible Pneumatic Tools – Collated 31–34° Plastic Strip and Paper Tape
Bostitch®
DeWalt ®
Duofast ®
Hitachi®
Makita®
MAX®
Paslode®
Porter Cable®
Senco®
Spotnails ®
F33PT, N90PT (2"–31⁄2")
D51823, D51822
NSPM-325F & CN-325B
NR83AA & NR83AA2, NR90AA
AN942
SN890CH/34, GS683CH
F350S Powermaster Plus, Impulse 325 & 350, 5325S, 5300 Plus & 5350S,
F250S-PP, IMCT (2" to 31⁄4")
FC350, FC350A
SN4, SN70, FramePro 600 & FramePro 650, SN325 +, FramePro 601 (up to 31⁄2")
& FramePro 701XP (up to 31⁄2"), FramePro 651 (up to 31⁄2"), FramePro 750XL
(up to 31⁄2") & FramePro 751XP (up to 31⁄2")
YTD90
17
DECKING
Collated Nails
COLLATED NAILS | Wire Coil 15°, Ring Shank
• 15° collation angle; stainless-steel collation medium
Penny
Size
Length
Shank
Diameter
Head
Size
Box
Count
Item No.
Available
in 316*
4d
1 1⁄2"
.099"
1
5d
3
1 ⁄4"
.099"
1
⁄4"
3600
S12A150PNB
—
6d
2"
.099"
1
⁄4"
3600
S12A175PNB
—
⁄4"
3600
S12A200PNB
—
7d
2 1⁄4"
.099"
1
8d
2 1⁄2"
.099"
1
**
8d
2 3⁄8"
.113"
1
⁄4"
1800
T12A225PNJ
⁄4"
3600
S12A250PNB
⁄4"
3600
S12A237PNB
⁄64"
1800
S11A300PNJ
⁄64"
1800
S10A300PNJ
⁄64"
1800
S11A325PNJ
⁄64"
1800
S10A325PNJ
⁄64"
1800
T10A350PNJ
10d
3"
.120"
17
10d
3"
.131"
17
12d
3 1⁄4"
.120"
17
12d
3 1⁄4"
.131"
17
16d
3 1⁄2"
.131"
17
** Item available in 316 stainless steel only.
—
**
Bostitch®
Fasco®
Hitachi®
Makita®
MAX®
Paslode®
Porter Cable®
Senco®
Spotnails ®
Bostitch N80CB, N86C & N100C, N100CPP, N130C-2
F5C CN15W75 (up to 3") & CN15W90 (up to 31⁄4")
NV65AB & NV65AC (up to 21⁄2"), NV83A (up to 31⁄4"), NV75AG (.099" to .131", 13⁄4" to 3")
AN621 (13⁄4"–21⁄2"), AN901 (13⁄4"–31⁄2")
CN80, CN70 (13⁄4" to 23⁄4"), HN75, HN90, 80F, CN100 (21⁄2" to 4"), CN565S (13⁄4" to 21⁄2"), CN890II,
CN565 (11⁄2" to 21⁄2"), CN890S, CN665 (11⁄2" to 21⁄2"), CN565D (13⁄4" to 21⁄2"), CN565S (13⁄4" to 21⁄2")
F325C, P350C (11⁄2" to 31⁄4"), F275C, P275C (11⁄2" to 23⁄4"), 4275/CN70 (2" to 21⁄2"),
5325/CN80 & 5350C, 5300C (up to 3")
Coil 350 (up to 31⁄2") , Coil 250 (up to 21⁄2")
SCN56 (up to 21⁄2"), SCN60 (2" to 21⁄2"), SCN65 (2" to 31⁄2") & SCN300 (13⁄4" to 3")
MCW64 (up to 21⁄2"), YCN83 (up to 31⁄4")
COLLATED NAILS | Wire Weld 28°, Clipped Head, Ring Shank
• 28° collation angle
• Clipped head, welded wire collation
304 Stainless Steel
Length
Shank
Diameter
Box
Count
Item No.
2 3⁄8"
.113"
1000
S12A237W28
3"
.120"
1000
S11A300W28
3 1⁄4"
.131"
1000
S10A325W28
Compatible Pneumatic Tools – Collated 28° Wire Weld
Bostitch®
Craftsman®
Max®
Porter Cable®
18
N16, N80SB,N86S (2" to 31⁄2"), N88WW, N100S,
N70S & N70SB (2" to 3"), N100S (2" to 4")
18430
SN890CH/28
FM350A
Compatible Pneumatic Tools – Collated 15° Wire Coil
DECKING
Hand-Drive Screws
HAND-DRIVE SCREWS | Swaneze™ Trim Head, Square Drive
•
•
•
•
•
•
•
•
•
•
•
Type-17 point for fast starts
Trim head
Coarse threads approximately 2⁄3 up the shank draw the decking tightly to the substrate
Pre-drilling recommended near board ends to prevent splitting
Use with stable woods and wood substitutes for less noticeable fastening
Deck Pack contains enough screws to fasten 100 square feet
(6" nominal boards on 16" centers)
#7 screw has 0.230" head diameter and #1 square drive recess
#9 x 3 1⁄2" screw has 0.250" head diameter and #1 square drive recess
#9 x4" screw has 0.250" head diameter and #2 square drive recess
Screws available in various packaging sizes and types from 1 lb. boxes to deck packs,
bulk cartons and durable buckets
Size
Length
Approx.
Count per lb.
Bucket
Count
5 lb.
Item No.
1 lb.
Item No.
Bucket
Item No.
Deck Pack
Item No.
70-Pack
Item No.
Available
in 316*
#7
1"
316
5000
S07100FB5
S07100FB1
S07100FBB
S07C100PAK
—
—
#7
1
1 ⁄4"
256
5000
S07125FB5
S07125FB1
S07125FBB
S07C125PAK
—
—
#7
15⁄8"
195
1750
S07162FB5
S07162FB1
S07162FBBKT**
S07162BFBP**
S07162BFBR70**
#7
2"
154
4000
S07200FB5
S07200FB1
S07200FBB
S07C200PAK
—
#7
2 1⁄4"
138
1750
S07225FB5
S07225FB1
S07225FBBKT**
S07225BFBP**
S07225BFBR70**
#7
2 1⁄2"
126
2500
S07250FB5
S07250FB1
S07250FBB
S07C250PAK
—
—
#7
3"
98
1750
S07300FB5
S07300FB1
S07300FBBKT**
S07300BFBP**
S07300BFBR70**
#9
3 1⁄2"
62
1500
S09350FB5
S09350FB1
S09350FBB
S09C350PAK
—
—
#9
4"
61
1000
S09400FB5
S09400FB1
S09400FBB
—
—
—
** Includes #1 square-drive bit.
—
HAND-DRIVE SCREWS | Swaneze™ Trim Head, 6-Lobe Drive
•
•
•
•
•
•
•
•
0.230" diameter T-15 6-lobe drive, trim head
6-lobe drive prevents driver bit cam-out and stripping in recess
Use with stable woods and wood substitutes for less noticeable fastening
Slender #7 shank for finish work and trim
Size
Length
6-Lobe
Drive
Approx.
Count per lb.
Carton/Bucket
Count
#7
15⁄8"
T-15
195
4000
#7
2 1⁄4"
T-15
138
3000
#7
3"
T-15
98
2000
SO7300FTC
Bulk Carton
Item No.
Bucket
Item No.
Deck Pack
Item No.
Available
in 316*
S07162FTC
S07162FTB
SO7C162FTP
—
S07225FTC
S07225FTB
S07C225FTP
S07300FTB
S07C300FTP
—
19
DECKING
Hand-Drive Screws
HAND-DRIVE SCREWS | Swaneze™ Bugle Head, Square Drive
•
•
•
•
•
0.344" diameter, #2 square drive bugle head
Length
⁄8"
#6
5
#6
3
Approx.
Carton/Bucket
Count per lb.
Count
1 lb.
Item No.
Bulk Carton
Item No.
Bucket
Item No.
Deck Pack
Item No.
Available
in 316*
408
12,000
S06062DB5
S06062DB1
S06062DBC
S06062DBB
—
—
⁄4"
352
10,000
S06075DB5
S06075DB1
S06075DBC
S06075DBB
—
—
#6
1"
295
8000
S06100DB5
S06100DB1
S06100DBC
S06100DBB
—
—
#6
1 ⁄4"
243
5000
S06125DB5
S06125DB1
S06125DBC
S06125DBB
—
—
#6
1
5
1 ⁄8"
195
4000
S06162DB5
S06162DB1
S06162DBC
S06162DBB
—
—
⁄4"
285
10,000
S08075DB5
S08075DB1
S08075DBC
S08075DBB
—
—
#8
1
1 ⁄8 "
226
5000
S08112DB5
S08112DB1
S08112DBC
S08112DBB
—
—
#8
1 1⁄4"
185
5000
S08125DB5
S08125DB1
S08125DBC
S08125DBB
S08C125PAK
#8
1 5⁄8"
150
4000
S08162DB5
S08162DB1
S08162DBC
S08162DBB
S08C162PAK
#8
3
#8
2"
128
3000
S08200DB5
S08200DB1
S08200DBC
S08200DBB
S08C200PAK
#8
2 1⁄4"
109
3000
S08225DB5
S08225DB1
S08225DBC
S08225DBB
S08C225PAK
#8
1
2 ⁄2"
102
2000
S08250DB5
S08250DB1
S08250DBC
S08250DBB
S08C250PAK
#8
3"
82
1500
S08300DB5
S08300DB1
S08300DBC
S08300DBB
S08C300PAK
—
#10
1"
S10100DB5
S10100DB1
S10100DBC
S10100DBB
—
—
—
172
4500
#10
1
1 ⁄4"
153
4000
S10125DB5
S10125DB1
S10125DBC
S10125DBB
—
—
#10
1 1⁄2"
134
3500
S10150DB5
S10150DB1
S10150DBC
S10150DBB
—
—
#10
3
1 ⁄4"
115
3000
S10175DB5
S10175DB1
S10175DBC
S10175DBB
—
—
#10
2"
96
2500
S10200DB5
S10200DB1
S10200DBC
S10200DBB
—
#10
2 1⁄4"
S10225DB5
S10225DB1
S10225DBC
S10225DBB
—
88
2000
#10
1
2 ⁄2"
82
2000
S10250DB5
S10250DB1
S10250DBC
S10250DBB
S10C250PAK
#10
3"
68
1500
S10300DB5
S10300DB1
S10300DBC
S10300DBB
S10C300PAK
#10
3 1⁄2"
56
1000
S10350DB5
S10350DB1
S10350DBC
S10350DBB
S10C350PAK
#10
3 3⁄4"
54
1000
S10375DB5
S10375DB1
S10375DBC
S10375DBB
—
20
5 lb.
Item No.
—
—
Size
DECKING
Hand-Drive Screws
HAND-DRIVE SCREWS | Swaneze Boardwalk™ Bugle Head, Square Drive
• 0.430" diameter #3 square drive bugle head
• Type-17 point for fast starts
• Coarse threads approximately 2⁄3 up the shank draw the decking
tightly to the substrate
• Pre-drilling recommended near board ends to prevent splitting
Approx.
Carton/Bucket
Count per lb.
Count
Size
Length
#12
2 1⁄2"
56
#12
3"
Bucket
Item No.
5 lb.
Item No.
1 lb.
Item No.
2000
S12250DBC
S12250DBB
S12250DB5
S12250DB1
48
1500
S12300DBC
S12300DBB
S12300DB5
S12300DB1
#12
1
3 ⁄2"
42
1000
S12350DBC
S12350DBB
S12350DB5
S12350DB1
#12
4"
36
800
S12400DBC
S12400DBB
S12400DB5
S12400DB1
#12
1
4 ⁄2"
32
750
S12450DBC
S12450DBB
S12450DB5
S12450DB1
#12
5"
29
500
S12500DBC
S12500DBB
S12500DB5
S12500DB1
#12
5 1⁄2"
28
500
S12550DBC
S12550DBB
S12550DB5
S12550DB1
#12
6"
24
600
S12600DBC
S12600DBB
S12600DB5
S12600DB1
#14
3"
36
1000
S14300DBC
S14300DBB
S14300DB5
S14300DB1
#14
3 1⁄2"
33
750
S14350DBC
S14350DBB
S14350DB5
S14350DB1
#14
4"
26
700
S14400DBC
S14400DBB
S14400DB5
S14400DB1
#14
5"
21
500
S14500DBC
S14500DBB
S14500DB5
S14500DB1
#14
6"
18
500
T14600DBC
T14600DBB
T14600DB5
T14600DB1
Bulk Carton
Item No.
Available
in 316*
**
HAND-DRIVE SCREWS | Swaneze™ Bugle Head, 6-Lobe Drive
•
•
•
•
•
•
0.344" diameter T-15, T-20 and T-25 6-lobe drives
Size
Length
#6
1 1⁄4"
6-Lobe
Approx.
Carton/Bucket
Drive Count per lb.
Count
Bulk Carton
Item No.
Bucket
Item No.
5 lb.
Item No.
1 lb.
Item No.
Deck Pack
Item No.
Available
in 316*
T-15
243
5000
S06125DTC
S06125DTB
S06125DT5
S06125DT1
—
—
#6
5
1 ⁄8"
T-15
195
4000
S06162DTC
S06162DTB
S06162DT5
S06162DT1
—
—
#8
1 5⁄8"
T-20
150
4000
—
S08162DTB
S08162DT5
S08162DT1
—
—
—
#8
2"
T-20
128
3000
S08200DTC
S08200DTB
S08200DT5
S08200DT1
—
#10
2 1⁄2"
T-25
82
2000
S10250DTC
S10250DTB
S10250DT5
S10250DT1
S10C250DTP
#10
3"
T-25
68
1500
S10300DTC
S10300DTB
S10300DT5
S10300DT1
S10C300DTP
#10
3 ⁄2"
T-25
56
1000
S10350DTC
S10350DTB
S10350DT5
S10350DTI
—
1
—
21
DECKING
Hand-Drive Screws
HAND-DRIVE SCREWS | Dexxter ™ Composite Decking, 6-Lobe Drive
• Unique thread form removes exhaust while driving to reduce
“mushrooming” in composite decking
• 6-lobe drive prevents driver bit cam-out and stripping in recess
• Small head diameter is less visible
• Painted heads available, see page 27
• 6-lobe driver bit included in both Contractor Packs and Deck Packs
• Patent pending
Size
Length
Head
Diameter
6-Lobe
Drive
Carton
Count
Bulk Carton
Item No.
#10
1 1⁄2"
0.265"
T-20
1750
S10150DXB
#10
2"
0.265"
T-20
1750
S10200DXB
Deck Pack
Count
Deck Pack
Item No.
Available
in 316*
350
S10150DXP
—
350
S10200DXP
—
#10
1
2 ⁄2 "
0.265"
T-20
1750
S10250DXB
350
S10250DXP
#10
3"
0.265"
T-20
1750
S10300DXB
350
S10300DXP
—
!
Deck Packs contain enough screws to fasten 100 sq. ft. (6" nominal boards on 16" centers).
Contractor Packs contain enough screws to fasten 500 sq. ft. (6" nominal boards on 16" centers).
All square drive and 6-lobe-drive screws are
best driven using our specialty driver bits.
Our bits are manufactured in the U.S.A. to our
exacting standards – resulting in far fewer
stripped recesses, longer bit life, less waste,
and greater efficiency (see page 86).
22
DECKING
Hand-Drive Screws
HAND-DRIVE SCREWS | Woodpeckers ™ Flat Head, 6-Lobe Drive
•
•
•
•
•
•
•
•
Penetrate the hardest wood products with ease
Unique 4-corner thread form with raised-ridge technology greatly reduces driving torque
Self-countersinking nibs under the head ensure flush installation
Choose type 316 stainless steel for superior corrosion resistance
Threaded approximately 2⁄3 up the shank to tightly draw the decking to the joist
6-lobe driver bit included in both Contractor Packs and Deck Packs
316 Stainless Steel
Head
Diameter
6-Lobe
Drive
Carton
Count
Bulk Carton
Item No.
Deck Pack
Count
Deck Pack
Item No.
Size
Length
#8
1 5⁄8"
0.340"
T-20
4000
T08162WPB
350
T08162WPP
#8
2"
0.340"
T-20
3000
T08200WPB
350
T08200WPP
#10
2 1⁄2"
0.370"
T-25
1750
T10250WPB
350
T10250WPP
#10
3"
0.370"
T-25
1750
T10300WPB
350
T10300WPP
#10
3 1⁄2"
0.370"
T-25
1000
T10350WPB
250
T10350WPP
#12
4"
0.440"
T-27
750
T12400WPB
100
T12400WPP
HAND-DRIVE SCREWS | Woodpeckers ™ Trim Head, 6-Lobe Drive
•
•
•
•
•
•
•
•
0.230" diameter casing-style head and slender #7 diameter for finish work and trim
Threaded approximately 2⁄3 up the shank to tightly draw the decking to the substrate
Choose type 316 stainless steel for superior corrosion resistance
Head
Diameter
6-Lobe
Drive
Carton
Count
Bulk Carton
Item No.
Deck Pack
Count
1 5⁄8"
0.230"
T-15
1750
T07162WPBKT
350
#7
2 1⁄4"
0.230"
T-15
1750
T07225WPB
350
#7
3"
0.230"
T-15
1750
T07300WPB
350
#8
2 1⁄2"
0.260"
T-15
1750
S08250WPB
350
Size
Length
#7
Deck Pack
Item No.
70-Pack
Item No.
Available
in 316
T07162WPP
T07162WPR70
**
T07225WPP
T07225WPR70
**
T07300WPP
T07300WPR70
**
S08250WPP
—
—
23
DECKING
Hand-Drive Screws with Painted Heads
HAND-DRIVE SCREWS | Swaneze™ Painted Trim Head, Square Drive
•
•
•
•
•
•
•
•
Durable, powder-coated finish – painted heads blend with decking material
0.230" diameter #1 square drive, trim head
Use with stable woods and wood substitutes when screw heads need to be hidden
Choose type 316 for seaside applications
and superior corrosion resistance
Mocha Azek
Gray
Size
Length
Head Color
#7
#7
#7
#7
#7
#7
#7
#7
#7
#7
#7
#7
#7
#7
#7
#7
1 5⁄8"
1 5⁄8"
1 5⁄8"
1 5⁄8"
2 1⁄4"
2 1⁄4"
2 1⁄4"
2 1⁄4"
2 1⁄4"
2 1⁄4"
2 1⁄4"
2 1⁄4"
2 1⁄4"
3"
3"
3"
Gray
Ipê
Tan
White
Almond
Black
Gray
Ipê
Khaki
Tan
White
Azek Gray
Mocha
Gray
Ipê
Tan
Contractor Pack
Count
1750
1750
1750
1750
1750
1750
1750
1750
1750
1750
1750
1750
1750
1750
1750
1750
Tan
Gray Almond Ipê
Contractor Pack
Item No.
T07162FCG
S07162FCI
T07162FCT
T07162FCW
S07225FCA
S07225FCBB
S07225FCG
S07225FCI
S07225FBK
S07225FCT
S07225FCW
S07225FCZ
S07225FCM
S07300FCG
S07300FCI
S07300FCT
Black White Khaki
Deck Pack
Count
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
Deck Pack
Item No.
T07162FJG
S07162FJI
T07162FJT
S07162FJW
S07225FJA
S07225FJB
S07225FJG
S07225FJI
S07225FJK
S07225FJT
S07225FJW
S07225FZJ
S07225FJM
S07300FJG
S07300FJI
S07300FJT
Available
in 316*
**
**
—
—
—
—
—
—
—
—
•
•
•
•
•
•
•
•
Heads colored to match “Trex Escapes ®” PVC decking
0.230" diameter 6-lobe drive trim head
24
Size
Length
Head Color
6-Lobe
Drive
Contractor
Pack Count
#7
#7
#7
#7
#7
#7
#8
#8
#8
#8
#8
#8
#8
#8
1 5⁄8"
2 1⁄4"
2 1⁄4"
2 1⁄4"
2 1⁄4"
2 1⁄4"
2 1⁄2"
2 1⁄2"
2 1⁄2"
2 1⁄2"
2 1⁄2"
2 1⁄2"
2 1⁄2"
2 1⁄2"
White
Acorn
Black
Lt. Gray
Pewter
Sahara
Almond
Gray
Jatoba
Khaki
Tan
Mocha
White
Gray
T-15
T-15
T-15
T-15
T-15
T-15
T-15
T-15
T-15
T-15
T-15
T-15
T-15
T-15
1750
1750
1750
1750
1750
1750
1750
1750
1750
1750
1750
1750
1750
1750
Contractor Pack Deck Pack
Item No.
Count
S07162TCW
S07225TCA
S07225TCB
S07225TCG
S07225TCE
S07225TCS
T08250FCA
S08250TCG
S08250TCJ
T08250FBK
S08250TCT
T08250FCM
T08250FCW
T08250FZC
350
350
350
350
350
350
350
350
350
350
350
350
350
350
Deck Pack
Item No.
S07162TJW
S07225TJA
S07225TJB
S07225TJG
S07225TJE
S07225TJS
T08250FJA
S08250TJG
S08250TJJ
T08250FJK
S08250TJT
T08250FJM
T08250FJW
T08250FZJ
Available
in 316*
Acorn
Black Lt. Gray
Pewter Sahara White
**
—
—
**
—
**
**
**
Almond Khaki
Mocha
Tan
Gray
Jatoba
HAND-DRIVE SCREWS | Swaneze™ Painted Trim Head, 6-Lobe Drive
DECKING
HAND-DRIVE SCREWS | Swaneze™ Painted Bugle Head, Square Drive
•
•
•
•
0.344" diameter #2 square drive bugle head
Coarse threads approximately 2⁄3 up the shank draw board
• Pre-drilling recommended near board ends
to prevent splitting
Ipê
Tan
Gray
305 Stainless Steel
!
Head Color
Contractor Pack
Count
Contractor Pack
Item No.
Deck Pack
Count
Deck Pack
Item No.
Size
Length
#10
2 1⁄2"
Ipê
1750
S10250DCI
350
S10250DJI
#10
2 1⁄2"
Tan
1750
S10250DCT
350
S10250DJT
#10
3"
Gray
1750
S10300DCG
350
S10300DJG
#10
3"
Ipê
1750
S10300DCI
350
S10300DJI
#10
3"
Tan
1750
S10300DCT
350
S10300DJT
Did you know that we were the first to introduce the stainless-steel, square-driven deck screw to
the U.S. market in 1989? Even today our Swaneze™ screws remain an industry standard.
HAND-DRIVE SCREWS | Standard Coated Trim Head, Square Drive
•
•
•
•
•
•
•
Trim head offers a clean, finished look
Self-countersinking nibs under the head ensure flush installation
Available with a Quik Guard® double-barrier coating and in stainless steel
#2 Undersized square drive
Type-17 tip for fast starts
Driver bit included in each package
NOTE: Quik Guard ® coating has been tested to show less than 10% of surface red rust
at 950 hours of ASTM B117 salt spray testing. It is suitable for exterior applications with
most preservative-treated woods. It is not suitable for higher exposure environments
such as seaside applications, see www.strongtie.com/info for more information.
Quik Guard® Coating and 305 Stainless Steel
Color
70-Count Box
Item No.
350-Count Box
Item No.
1750-Count Box
Item No.
2 1⁄2"
Gray
DTHG212R70
DTHG212R350
DTHG212MB
#8
2 1⁄2"
Brown
DTHB212R70
DTHB212R350
DTHB212MB
#8
2 ⁄2"
Red
DTHR212R70
DTHR212R350
DTHR212MB
#8
2 1⁄2"
Tan
DTHT212R70
DTHT212R350
DTHT212MB
#8
2 1⁄2"
Stainless Steel
DTHSS212R70
DTHSS212R350
—
#8
3"
Gray
DTHG3R70
DTHG3R350
DTHG3MB
#8
3"
Brown
DTHB3R70
DTHB3R350
DTHB3MB
#8
3"
Red
DTHR3R70
DTHR3R350
DTHR3MB
#8
3"
Tan
DTHT3R70
DTHT3R350
DTHT3MB
#8
3"
Stainless Steel
DTHSS3R70
DTHSS3R350
—
Size
Length
#8
1
Brown
Gray
Tan
Red
25
DECKING
HAND-DRIVE SCREWS | Composi-Lok™ Composite, Coated, Square Drive
• Cutting wings on the shaft counter-bore the deck board, helping
to prevent fastener spin out
• Cap-style head reduces mushrooming material, ensuring a
cleaner-looking installation
• Available with a Quik Guard® double-barrier coating and in stainless steel
• #2 Undersized square drive
• Sharp point
• Driver bit included in each package
NOTE: Quik Guard ® coating has been tested to show less than 10% of surface red rust
at 950 hours of ASTM B117 salt spray testing. It is suitable for exterior applications with
most preservative-treated woods. It is not suitable for higher exposure environments
such as seaside applications, see www.strongtie.com/info for more information.
Quik Guard® Coating and 305 Stainless Steel
Length
Color
70-Count Box
Item No.
350-Count Box
Item No.
1750-Count Box
Item No.
#9
2 1⁄2"
Gray
DCLG212R70
DCLG212R350
DCLG212MB
#9
1
2 ⁄2"
Brown
DCLB212R70
DCLB212R350
DCLB212MB
#9
2 1⁄2"
Red
DCLR212R70
DCLR212R350
DCLR212MB
#9
2 1⁄2"
Tan
DCLT212R70
DCLT212R350
DCLT212MB
#9
2 1⁄2"
Stainless Steel
DCLSS212R70
DCLSS212R350
—
#9
3"
Gray
DCLG3R70
DCLG3R350
DCLG3MB
#9
3"
Brown
DCLB3R70
DCLB3R350
DCLB3MB
#9
3"
Red
DCLR3R70
DCLR3R350
DCLR3MB
#9
3"
Tan
DCLT3R70
DCLT3R350
DCLT3MB
#9
3"
Stainless Steel
DCLSS3R70
DCLSS3R350
—
Size
26
DECKING
HAND-DRIVE SCREWS | Woodpeckers ™ Painted Trim Head, 6-Lobe Drive
•
•
•
•
•
•
•
•
•
Durable, powder-coated finish – painted heads blend with Ipê decking material
0.230" diameter casing-style head and slender #7 diameter for finish work and trim
Choose type 316 stainless steel for seaside applications and superior corrosion resistance
Ipê
Size
Length
Head
Diameter
6-Lobe
Drive
Contractor Pack
Count
Contractor Pack
Item No.
Deck Pack
Count
Deck Pack
Item No.
Available
in 316
#7
2 1⁄4"
0.230"
T-15
1750
T07225WCI
350
T07225WJI
**
#8
2 ⁄2"
0.260"
T-15
1750
S08250WCI
350
S08250WJI
—
1
HAND-DRIVE SCREWS | Dexxter ™ Composite Decking , Painted Trim Head, 6-Lobe Drive
•
•
•
•
•
•
•
Unique thread form removes exhaust while driving to reduce “mushrooming” in composite decking
Small head diameter is less visible
6-lobe driver bit included in both Contractor Packs
and Deck Packs
• Patent pending
Brown
305 Stainless Steel
!
6-Lobe
Drive
Gray
Contractor Pack
Count
Ipê
Tan
Redwood
Contractor Pack
Item No.
Deck Pack
Count
Deck Pack
Item No.
Size
Length
Head Color
#10
1 1⁄2"
Brown
T-20
1750
S10150XBB
350
S10150XPB
#10
1 1⁄2"
Gray
T-20
1750
S10150XBG
350
S10150XPG
#10
1 1⁄2"
Ipê
T-20
1750
S10150XBI
350
S10150XPI
#10
1 1⁄2"
Redwood
T-20
1750
S10150XBR
350
S10150XPR
#10
1 1⁄2"
Tan
T-20
1750
S10150XBT
350
S10150XPT
#10
2 1⁄2"
Gray
T-20
1750
S10250XBG
350
S10250XPG
#10
2 1⁄2"
Redwood
T-20
1750
S10250XBR
350
S10250XPR
#10
2 1⁄2"
Tan
T-20
1750
S10250XBT
350
S10250XPT
#10
2 1⁄2"
Ipê
T-20
1750
S10250XBI
350
S10250XPI
#10
1
2 ⁄2"
Brown
T-20
1750
S10250XBB
350
S10250XPB
#10
3"
Gray
T-20
1750
S10300XBG
350
S10300XPG
#10
3"
Ipê
T-20
1750
S10300XBI
350
S10300XPI
#10
3"
Redwood
T-20
1750
S10300XBR
350
S10300XPR
#10
3"
Tan
T-20
1750
S10300XBT
350
S10300XPT
Contractor Packs contain enough screws to fasten 500 sq. ft. (6" nominal boards on 16" centers).
27
DECKING
EB-TY ® Hidden Deck Fastening
EB-TY® | Hidden Deck Fastening
The EB-TY provides a unique method of fastening deck boards that makes the fasteners
virtually invisible. Fastening is done into the side of the board, leaving a fastener-free
deck surface.
The EB-TY is a polypropylene biscuit fastener that fits into a slot the builder cuts into the
edge of the deck boards with a standard biscuit joiner. The EB-TY fasteners are inserted
and fastened with a screw driven into the joist. Nesting each successive board against
the EB-TY automatically ensures consistent spacing and uniform height.
• Easy to install since all fastening is done from the top side
• Affords easier deck resurfacing since nail heads are eliminated from
the deck surface
• Formed from UV resistant polypropylene to last the life of the deck
• Stainless-steel #7 trim-head screws included
• Each EB-TY Deck Pack includes installation instructions and enough EB-TY fasteners,
screws and tapered Ipê wood plugs to install 100 square feet of decking (assuming
6" wide boards, installed perpendicular to joists spaced 16" on center)
Board
Thickness
Board
Spacing
#7 Screw
Length
6"/16" O.C.
1"+
3
6"/16" O.C.
1"+
3
6"/24" O.C.
1"+
3
EB-TY
Model
Deck Pack
Count
⁄32"
2 1⁄4"
EBE004
175
175-EBTYS
⁄32"
2 1⁄4"
EBE004
175
175-EBTYW*
⁄32"
2 1⁄4"
EBE004
100
100-EBTYS
⁄32"
1
2 ⁄4"
EBE004
275
275-EBTYS
⁄32"
15⁄8"
EBE004
175
175-EB162
⁄8"
1
2 ⁄4"
EBE004
175
175-EBTYPV
⁄4"
2 1⁄4"
EBE005LC
175
175-EBTYLC
⁄4"
1
2 ⁄4"
EBE005LC
175
175-EBTYLW*
⁄4"
2 1⁄4"
Deck Pack
Item No.
4"/16" O.C.
1"+
3
6"/16" O.C.
1"+
3
6"/16" O.C.
1"+
1
6"/16" O.C.
1"+
1
6"/16" O.C.
1"+
1
6"/24" O.C.
1"+
1
EBE005LC
100
100-EBTYLC
4"/16" O.C.
1"+
1
⁄4"
2 1⁄4"
EBE005LC
275
275-EBTYLC
⁄32"
2 1⁄4"
EBE007MI
175
175-EBTYMI
⁄32"
2 1⁄4"
EBE007MI
100
100-EBTYMI
6"/16" O.C.
11
⁄16 "+
3
6"/24" O.C.
11
⁄16 "+
3
6"/16" O.C.
11
⁄16 "+
1
⁄4"
2 1⁄4"
EBE006JR
175
175-EBTYJR
2"+
1
⁄4"
2 1⁄4"
EBE002
175
175-EBTYBG
⁄16 "
2 1⁄4"
316-TT
175
175-EBTT
⁄16 "
2 1⁄4"
316-TS
175
175-EBTYP
6"/16" O.C.
6"/16" O.C.
11
⁄16 "+
3
6"/16" O.C.
11
⁄16 "+
3
Model EBE004
Model EBE005LC
Model EBE006JR
Model EBE007MI
*#7 trim-head Woodpeckers™ stainless-steel screws included – all others have #7 Swaneze™ trim-head screws included
Model 316-TS
Model 316-TT
Tapered Ipê
Wood Plugs see page 87
28
Board Width/
Joist Spacing
Model EBE002
DECKING
EB-TY ® Hidden Deck Fastening
Common Uses
Helpful Hints and Facts
If you have questions
about which EB-TY to use,
speak with one of our sales
professionals today – we look
forward to working with you!
• As with all decking materials, please consult manufacturer’s installation instructions for
deck height requirements and deck board spacing.
• All slots for the EB-TY’s (except for the TT) can be cut using a #20 setting with a biscuit
cutter/plate jointer or router with 5⁄32" slot cutter. Decking can be grooved the entire
length of the board.
• Always butt boards over a joist. One method for installing butt ends is to cut the keel
off the bottom of an EB-TY, slot the board ends, and insert the EB-TY. Another, more
reliable method is to face-screw and plug.
EBE002
True 1 1⁄2 " material or thicker
Popular in boardwalk construction
EBE004
Fasten one side of first deck
board using screws and plugs
1" and 1 1⁄4 " deck boards
Ipê, Cedar, Redwood, stable
composites
#7x 21⁄4" Swaneze
trim head screw
angled at 45°
EBE005LC
1" and 1 1⁄4 " kiln-dried boards
Brazilian Redwood, some Mahogany,
select composites
EBE006JR
⁄4 " kiln-dried boards
Brazilian Redwood, some Mahogany,
select composites
3
EBE007MI
⁄4 " boards
Ipê, Cedar, Redwood, stable
composites
3
EB-TY
biscuit fastener
316-TS
Composite decking, solid or
pre-grooved
Second deck board
fastened with EB-TY
and construction
adhesive applied to
top of floor joist
316-TT
Composite decking, pre-grooved with
a wider channel (e.g. Timber Tech®)
Installation
1. Fasten the first board using construction adhesive and screws, then cut slots where the
board intersects joists using a 5⁄32" router bit or plate joiner (biscuit cutter #20) and install
the first EB-TY fasteners. Do not use construction adhesive with composite decking (see right).
2. Cut slots in the next board where it intersects the joists.
3. Apply a bead of construction adhesive to the top of each joist and install the new board
so that the slots fit over the EB-TY fasteners installed in the first board.
!
Construction adhesive is not
recommended when installing
composite deck boards as some
adhesives will have an adverse
reaction upon contact with
certain plastics.
4. Insert EB-TY fasteners into each slot in the exposed edge of the board and fasten with screws.
5. Repeat the process until all boards are installed.
Refer to the installation instructions (included) for more information.
Consult composite decking manufacturer’s or wood supplier’s installation
instructions for deck height requirements and deck board spacing.
Pre-grooving the entire length of the deck board is a time-saving
alternative to individual grooves made with a router or plate joiner.
Some types of composite lumber are available with grooves as
an added feature. Have your lumber yard use the schematic
on the right to pregroove boards to accept EB-TY fasteners.
0.500"
Bring the schematic below to your
lumber yard. They will use it to
pre-groove your decking material to
accept EB-TY fasteners.
0.1630"
Cut groove at center of material thickness
*For model numbers 316-TS and 316-TT screws are to be driven at a 90° angle to the board face.
29
DECKING
Flooring Cleats and Staples
FLOORING CLEATS | “T” Series
• Ideal for tongue-and-groove decking
304 Stainless Steel
Gauge
Length
Box
Count
Item No.
16
2"
1000
S16B200TNL
Compatible Tools
Porta-Nails ®
Primatech®
Senco ®
401, 421, 501
H-300, H-330, P-210
SHF15
FLOORING CLEATS | “L” Series
304 Stainless Steel
Gauge
Length
Box
Count
Item No.
16
1 1⁄2"
1000
S16B150LCT
16
2"
1000
S16B200LCT
Bostitch®
Porter Cable®
Powernail®
Primatech®
Senco ®
MFN 200, MIIIFN
FCN 200
45, 101, 445 Series
H-300, H-330, P-210
SHF15, SHF50
FLOORING STAPLES | Similar to Bostitch® BCS Series
304 Stainless Steel, 1⁄2 " Crown
Box
Count
Gauge
Length
Item No.
15 1⁄2
1 3⁄4"
5000
S15N175BFS
15 1⁄2
2"
5000
S15N200BFS
Compatible Tools
Bostitch®
MIIIFS
!
Did you know that all of our collated brads, finish nails, staples and cleats are treated with a special coating that is
typically clear, but can also be yellow or green? Upon entry into wood this coating melts and acts as a lubricant.
Once the fastener cools, the coating dries – acting as an adhesive to increase pull-out resistance.
30
Compatible Tools
SIDING
SIDING
Fine Wood Siding
Whether you’re siding with Cedar, Redwood or Cypress, you’ll find that Simpson Strong-Tie
carries the right fastener for the job. Fine wood siding offers natural beauty, dimensional
stability, superior workability, and resistance to insect damage and decay given proper
treatment and maintenance.
The slender gauge of our hand-drive stainless-steel wood siding nails limits splitting,
and textured heads ensure a better blend with wood grains. Furthermore, our siding nails
are available pre-painted to match various siding materials.
Note that we carry wire coil siding nails (also available pre-painted) compatible with
a range of popular pneumatic nail guns.
Fiber Cement Siding
For siding offering strength, visual appeal and long-lasting durability regardless of climate,
many builders today look to fiber cement. Available in shingles, lap and panel profiles
in a variety of textures, most fiber cement siding products carry the added benefit of
transferable manufacturer’s warranties ranging from 25-50 years.
Our 316 stainless-steel Portland ™ fiber-cement hand-drive nails meet strict specifications
currently required by most manufacturers of lap and panel fiber cement. We also stock
collated Portland nails for use with pneumatic nail guns. Our stainless-steel screws come in
two versions: wood stud or metal stud. Both are manufactured expressly for fiber cement
applications and are self-countersinking to insure flush seating with work surfaces.
We stock a large selection of high quality,
stainless-steel siding fasteners offering
the combined benefits of strength,
durability and corrosion resistance.
You can count on Simpson Strong-Tie ®
Swan Secure products to endure the
challenges of harsh environmental
elements and time – in most cases
outlasting the life of the siding itself.
As always, we strongly recommend
our AISI-graded 316 stainless-steel
fasteners for seaside applications.
Fine Wood
Siding
Hand-Drive Nails
Wood Siding ................................................................................ 32
Shake and Shingle ....................................................................... 32
Painted Siding ............................................................................. 33
Fiber-Cement Siding, Portland ™ .................................................. 34
Pyramid Head Siding .................................................................. 34
Collated Nails
Wire Coil 15°, Ring-Shank, Siding ............................................... 35
Wire Coil 15°, Ring-Shank, Fiber-Cement Siding .......................... 35
Wire Coil 15°, Painted Siding ...................................................... 36
Plastic Coil 15°, Siding ................................................................ 36
Inserted Plastic Coil 15°, Siding.................................................. 37
Hand-Drive Screws
Fiber Cement
Siding
Fiber Cement, Fy-Cem ™ – Wood Stud ........................................ 37
Self-Drilling, Fy-Cem Billy Goats ™ – Metal Stud ......................... 38
Trim Head, Self-Drilling, Billy Goats ™ – Metal Stud ..................... 38
Hex Washer Head Panel, Twin Lead Thread ................................ 39
K-Lath, Modified Truss Head, Self-Drilling, Metal ...................... 40
K-Lath, Modified Truss Head, Wood ...........................................40
Collated Staples
Similar To:
Senco ® “N” Series....................................................................... 41
Paslode ® “GS” Series .................................................................. 41
Paslode ® “GSI” Series................................................................. 42
Bostitch® “BCS” Series ............................................................... 42
31
SIDING
Hand-Drive Nails
HAND-DRIVE NAILS | Wood Siding
• Premium-quality nails for cedar, redwood and cypress siding
• Slender gauge and blunt diamond point minimize splitting
• Generous fillet under nail head allows nails to be driven flush or countersunk without
crushing surrounding wood
• Checker-patterned head blends with wood texture, serves to diffract sunlight
and accept surface finishes
• Annular ring threads resist cupping of siding boards and nail-head popping
Penny
Size
Length
Gauge
Shank
Diameter
3d
1 1⁄4"
14
.083"
5
4d
1 1⁄2"
14
.083"
5
5d
1 3⁄4"
14
.083"
5
6d
2"
13
.095"
5
7d
2 1⁄4"
13
.095"
5
8d
1
2 ⁄2"
13
.095"
5
10d
3"
12
.109"
7
12d
3 1⁄4"
12
.109"
7
16d
3 1⁄2"
11
.120"
1
20d
4"
10
.134"
1
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
Bucket
Item No.
⁄32"
495
S3SND25
S3SND5
S3SND1
S3SNDB
⁄32"
398
S4SND25
S4SND5
S4SND1
S4SNDB
⁄32"
354
S5SND25
S5SND5
S5SND1
S5SNDB
⁄32"
245
S6SND25
S6SND5
S6SND1
S6SNDB
⁄32"
215
S7SND25
S7SND5
S7SND1
S7SNDB
⁄32"
196
S8SND25
S8SND5
S8SND1
S8SNDB
⁄32"
120
S10SND25
S10SND5
S10SND1
S10SNDB
⁄32"
110
S12SND25
S12SND5
S12SND1
S12SNDB
⁄4"
88
S16SND25
S16SND5
S16SND1
S16SNDB
⁄4"
74
S20SND25
S20SND5
S20SND1
S20SNDB
Available
in 316*
HAND-DRIVE NAILS | Shake and Shingle
• 7⁄32" diameter checker pattern flat head provides ample bearing surface
to firmly secure shakes and shingles of all types
• Slender shanks minimize splitting
• Annular ring threads resist cupping, wind damage and nail-head popping
Penny
Size
Length
Gauge
Shank
Diameter
3d
1 1⁄4"
14
.083"
7
4d
1
1 ⁄2 "
14
.083"
7
5d
1 3⁄4"
14
.083"
7
6d
2"
13
.095"
7
7d
1
2 ⁄4"
13
.095"
7
8d
2 1⁄2"
13
.095"
7
Head
Diameter
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
Bucket
Item No.
⁄32"
470
S3SN725
S3SN75
S3SN71
S3SN7B
⁄32"
394
S4SN725
S4SN75
S4SN71
S4SN7B
⁄32"
337
S5SN725
S5SN75
S5SN71
S5SN7B
⁄32"
237
S6SN725
S6SN75
S6SN71
S6SN7B
⁄32"
216
S7SN725
S7SN75
S7SN71
S7SN7B
⁄32"
196
S8SN725
S8SN75
S8SN71
S8SN7B
!
All of our hand-driven nails can be ordered passivated for a nominal up-charge. Passivation is a light
acid bath that cleans the fastener of surface contaminants and aids in preventing premature corrosion.
32
Available
in 316*
Head
Diameter
SIDING
Hand-Drive Nails
HAND-DRIVE NAILS | Painted Siding
• Premium-quality nails for cedar, redwood and cypress siding materials
• Slender gauge and blunt diamond point minimize splitting
• Generous fillet under nail head allows nails to be driven flush or countersunk without
• Checker-patterned head blends with wood texture and serves to diffract sunlight
• Custom colors available upon request (minimums apply) – call for details
• Choose type 316 for seaside applications
Cedar Dark Brown
Gray
Redwood
White
Penny
Size
Length
Gauge
Shank
Head
Diameter Diameter
6d
2"
13
.095"
5
6d
2"
13
.095"
5
6d
2"
13
.095"
5
6d
2"
13
.095"
5
6d
2"
13
.095"
5
8d
2 1⁄2"
13
.095"
5
8d
1
2 ⁄2"
13
.095"
5
8d
1
2 ⁄2"
13
.095"
5
8d
2 1⁄2"
13
.095"
5
8d
1
2 ⁄2"
13
.095"
5
10d
3"
12
.109"
7
10d
3"
12
.109"
7
10d
3"
12
.109"
7
10d
3"
12
.109"
7
10d
3"
12
.109"
7
Color
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
Bucket
Item No.
⁄32"
Cedar
245
S6SNDT25
S6SNDT5
S6SNDT1
S6SNDTB
⁄32"
Dark Brown
245
S6SNDB25
S6SNDB5
S6SNDB1
S6SNDBB
⁄32"
Gray
245
S6SNDG25
S6SNDG5
S6SNDG1
S6SNDGB
⁄32"
Redwood
245
S6SNDR25
S6SNDR5
S6SNDR1
S6SNDRB
⁄32"
White
245
S6SNDW25
S6SNDW5
S6SNDW1
S6SNDWB
⁄32"
Cedar
196
S8SNDT25
S8SNDT5
S8SNDT1
S8SNDTB
⁄32"
Dark Brown
196
S8SNDB25
S8SNDB5
S8SNDB1
S8SNDBB
⁄32"
Gray
196
S8SNDG25
S8SNDG5
S8SNDG1
S8SNDGB
⁄32"
Redwood
196
S8SNDR25
S8SNDR5
S8SNDR1
S8SNDRB
⁄32"
White
196
S8SNDW25
S8SNDW5
S8SNDW1
S8SNDWB
⁄32"
Cedar
120
S10SNDT25
S10SNDT5
S10SNDT1
S10SNDTB
⁄32"
Dark Brown
120
S10SNDB25
S10SNDB5
S10SNDB1
S10SNDBB
⁄32"
Gray
120
S10SNDG25
S10SNDG5
S10SNDG1
S10SNDGB
⁄32"
Redwood
120
S10SNDR25
S10SNDR5
S10SNDR1
S10SNDRB
⁄32"
White
120
S10SNDW25
S10SNDW5
S10SNDW1
S10SNDWB
Available
in 316*
!
Hammer Caps
When installing our painted siding
nails, remember that our hammer
caps are an inexpensive way to help
preserve the painted finish.
Model: HAMRCAP
33
SIDING
Hand-Drive Nails
HAND-DRIVE NAILS | Portland™ Fiber-Cement Siding
• Designed expressly for application of various lap and panel siding materials made of
fiber cement composites
• Extra-sharp point for optimum drivability
• Generous fillet under nail head allows nails to be driven flush with work surface
• Checker-patterned head diffracts sunlight, accepts surface finishes
• 1 1⁄4" roof head nails for blind-nailing lap siding, other sizes for face-nailing siding planks or panels
• Recommended for seaside applications and superior corrosion resistance
316 Stainless Steel
Penny
Size
Length
Gauge
Shank
Diameter
Head
Diameter
3d
1 1⁄4"
11
.120"
11
4d
1
1 ⁄2"
11
.120"
9
6d
2"
11
.120"
9
8d
2 1⁄2"
11
.120"
9
⁄32"
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
Bucket
Item No.
199
T3PCS25
T3PCS5
T3PCS1
T3PCSB
⁄32"
179
T4PCS25
T4PCS5
T4PCS1
T4PCSB
⁄32"
144
T6PCS25
T6PCS5
T6PCS1
T6PCSB
⁄32"
115
T8PCS25
T8PCS5
T8PCS1
T8PCSB
HAND-DRIVE NAILS | Pyramid Head
•
•
•
•
•
•
“Pyramid” style decorative heads are reminiscent of old rose-head nails
Lends a rustic look to face-nailed lap, bevel and board and batten siding jobs
Annular ring threads hold fast in wood substrates
316 stainless-steel nails highly visible on darker siding materials
Silicon bronze weathers to dark brown color
Bucket = 25 lbs.
Penny
Size
Length
Gauge
Shank
Diameter
6d
2"
11
.120"
1
8d
1
2 ⁄2"
11
.120"
1
10d
3"
11
.120"
1
16d
3 1⁄2"
11
.120"
1
Head
Diameter
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
Bucket
Item No.
⁄4"
144
I6PSN25
I6PSN5
I6PSN1
I6PSNB
⁄4"
115
I8PSN25
I8PSN5
I8PSN1
I8PSNB
⁄4"
99
I10PSN25
I10PSN5
I10PSN1
I10PSNB
⁄4"
88
I16PSN25
I16PSN5
I16PSN1
I16PSNB
BEVEL SIDING INSTALLATION CALCULATOR
Nominal Width
Exposed Face
Overlap
Nail Count Factor
Linear Foot
Nail Count Factor
Square Foot
4
2 1⁄2
1
0.75
3.60
6
1
4 ⁄2
1
0.75
2.03
8
1
6 ⁄2
1
1 ⁄8
0.75
1.43
10
8 1⁄2
1 1⁄2
0.75
1.13
12
10 ⁄2
1 ⁄2
0.75
0.90
1
1
How To Figure:
Multiply the linear feet or square feet by the nail count factor above. The result is the quantity of nails required.
• One (1) nail per stud – 16" on center
• Allowance for waste and loss should be added
34
Available
in 316*
Silicon Bronze and 316 Stainless Steel
SIDING
Collated Nails
•
•
•
•
Protect your investment in fine wood siding from hard-to-remove stains and streaks
Premium-quality nails for cedar, redwood and cypress siding materials
Slender gauge and blunt diamond point minimize splitting
Generous under-head fillet allows nails to be driven flush, or countersunk,
without crushing surrounding wood
304 Stainless Steel
Length
Shank
Diameter
1 1⁄4"
.090"
13
1
1 ⁄2"
.090"
13
1 3⁄4"
.090"
13
2"
.090"
13
2 ⁄16 "
.090"
13
2 1⁄2"
.090"
13
3
Head
Diameter
Box
Count
Item No.
⁄64"
3600
S13A125SNC
⁄64"
3600
S13A150SNC
⁄64"
3600
S13A175SNC
⁄64"
3600
S13A200SNC
⁄64"
3600
S13A219SNC
⁄64"
3600
S13A250SNC
!
316 Stainless Steel
Length
Shank
Diameter
1 1⁄2"
.090"
13
3
1 ⁄4"
.090"
13
2"
.090"
13
2 3⁄16 "
.090"
13
2 ⁄2"
.090"
13
1
Stainless-Steel Wire Collation
Head
Diameter
Box
Count
Item No.
⁄64"
1800
T13A150SNJ
⁄64"
1800
T13A175SNJ
⁄64"
1800
T13A200SNJ
⁄64"
1800
T13A219SNJ
⁄64"
1800
T13A250SNJ
Beware of collated nails that do not
specify either AISI grade 304 or 316
stainless steel. If the alloy is not
printed on the box or label, you don’t
know what you are getting. There
are several stainless-steel alloys
from which fasteners can be made –
304 and 316 being the most common
used in nail production. However,
some distributors have recently
resorted to selling inferior alloys
resulting in nails that fail to offer
the corrosion resistance and
strength our customers have come
to expect. Furthermore, be certain
that the wire collation medium
holding the nails together is also
stainless steel – Simpson Strong-Tie
only sells Swan Secure nails with
stainless-steel collation medium.
COLLATED NAILS | Wire Coil 15°, Ring Shank, Fiber-Cement Siding
304 Stainless Steel
Length
Shank
Diameter
Head
Diameter
Box
Count
Item No.
1 1⁄2"
.093"
.225"
3600
S13A150SNA
3
1 ⁄4"
.093"
.225"
3600
S13A175SNA
2"
.093"
.225"
3600
S13A200SNA
2 ⁄16 "
.093"
.225"
3600
S13A219SNA
2 1⁄2"
.093"
.225"
3600
S13A250SNA
3
Compatible Pneumatic Tools
Bostitch ®
Hitachi®
MAX®
Paslode ®
Senco ®
N63CP, N64C, N65CP, N66C
NV65AH, NV65AC
CN565, CN565S, CN70 (1 3⁄4" TO 2 3⁄4"), CN55 (1" TO 2 1⁄4")
3225/CN55
SCN55S
!
Your Nail Gun, Our Fasteners
Tool manufacturers are constantly
introducing new tools to the market.
If you don’t see your particular model
in our tool compatibility listings,
visit www.strongtie.com or call
any of our locations and a sales
professional will assist you in your
fastener selection.
35
SIDING
Collated Nails
COLLATED NAILS | Wire Coil 15°, Painted
•
•
•
•
•
Premium-quality nails for cedar, redwood and cypress siding materials
Stainless steel will last the life of wood siding without degrading in most environments
Generous under-head fillet allows nails to be driven flush, or countersunk,
without crushing surrounding wood
• Annular ring threads limit
cupping of siding boards and
nail-head popping
Length
Shank
Diameter
Head
Size
2"
.090"
13
2"
.090"
13
2"
.090"
13
2"
.090"
13
Item No.
⁄64"
Dark Brown
3600
S13A200CCB
⁄64"
Gray
3600
S13A200CCG
⁄64"
Redwood
3600
S13A200CCR
⁄64"
Cedar
3600
S13A200CCT
⁄64"
White
3600
S13A200CWH
⁄64"
Dark Brown
3600
S13A219SNB
⁄64"
White
3600
S13A219SNW
⁄64"
Gray
3600
S13A219SNG
⁄64"
Redwood
3600
S13A219SNR
2"
.090"
.090"
13
2 ⁄16 "
.090"
13
2 ⁄16 "
.090"
13
2 3⁄16 "
.090"
13
2 ⁄16 "
.090"
13
2 1⁄2"
.090"
13
2 1⁄2"
.090"
13
1
2 ⁄2"
.090"
13
2 1⁄2"
.090"
13
2 ⁄2"
.090"
13
3
1
White
Box
Count
2 3⁄16 "
3
Redwood
Color
13
3
Gray
⁄64"
Cedar
3600
S13A219SNT
⁄64"
Dark Brown
3600
S13A250CCB
⁄64"
Gray
3600
S13A250CCG
⁄64"
Redwood
3600
S13A250CCR
⁄64"
Cedar
3600
S13A250CCT
⁄64"
White
3600
S13A250CWH
Bostitch ®
Hitachi®
MAX®
Paslode ®
Senco ®
NV65AH, NV65AC
CN565, CN565S, CN70 (1 3⁄4" TO 2 3⁄4"), CN55 (1" TO 2 1⁄4")
3225/CN55
SCN55S
COLLATED NAIL | Plastic Coil 15°
304 Stainless Steel for Hitachi
®
Gauge
Shank
Diameter
1 3⁄4"
14
.086"
.203"
4000
S14A175SNC
2"
14
.086"
.203"
4000
S14A200SNC
Size
Length
5d
6d
Hitachi ®
36
NV50AA, VH650, VH500
Head
Diameter
Box
Count
Item No.
Cedar Dark Brown
304 Stainless Steel
SIDING
Collated Nails / Hand-Drive Screws
COLLATED NAILS | Inserted Plastic Coil 15°
Size
Length
Gauge
Shank
Diameter
Head
Diameter
Box
Count
Item No.
4d
1 1⁄2"
13
.095"
.203"
3200
S13A150IPC
5d
3
1 ⁄4"
13
.095"
.203"
3200
S13A175IPC
6d
2"
13
.095"
.203"
3200
S13A200IPC
7d
2 1⁄4"
13
.095"
.203"
2400
S13A225IPC
8d
2 1⁄2"
13
.095"
.203"
2400
S13A250IPC
Available
in 316*
Bostitch®
Hitachi®
Makita®
MAX®
Paslode®
Senco®
N63CP, N66C
NV65AH, NV65AE, NV75AG (.099" to .131" 1 3⁄4" to 3")
AN611
CN565, CN565S (1 1⁄2" to 2 1⁄2")
4250-6C-P
SCN55S
Silicon Bronze
Size
Length
Gauge
Shank
Diameter
Head
Diameter
Box
Count
Item No.
8d
2 1⁄2"
13
.095"
.203"
2400
I13A250IPC
304 Stainless Steel for Duofast Model KDN50
Size
Length
Gauge
Shank
Diameter
Head
Diameter
Box
Count
Item No.
5d
1 3⁄4"
12
.099"
.210"
9000
S12A175DNB
7d
2 ⁄4"
12
.099"
.210"
7200
S12A225DNB
1
Duofast ®
KDN50, RCN60, RCN70, CNP-60Y, CNP-65Y
HAND-DRIVE SCREWS | FY-CEM™ Fiber Cement, Wood Stud
•
•
•
•
•
•
#2 square drive, coarse thread full length
Self-countersinking nibs under head insure seating of screw head flush with work surface
Threaded to within 5⁄16" of head
Use 1 1⁄4" screws to attach fiber cement siding to stress skin panels
Use 1 5⁄8" screws to blind-fasten fiber cement lap siding to wood
316 Stainless Steel
Size
Length
Head Diameter
Carton Count
Item No.
#8
1
1 ⁄4"
.390"
100
T08C125WQC
#8
1
1 ⁄4"
.390"
1000
T08C125WQM
#8
1 5⁄8"
.390"
100
T08C162WQC
#8
5
1 ⁄8"
.390"
1000
T08C162WQM
#8
2 1⁄4"
.390"
1000
T08C225WQM
#8
2 1⁄4"
.390"
2000
T08C225WQC
37
SIDING
Hand-Drive Screws
HAND-DRIVE SCREWS | FY-CEM™ Billy Goats™, Self Drilling, Fiber-Cement, Metal Stud
•
•
•
•
•
Fasten fiber cement through furring strips to steel studs
#2 square drive wafer head, #3 drill point
Self-countersinking nibs under head insure seating of screw head flush with work surface
Threaded to within 5⁄16" of top of head
Drilling thickness capacity: up to 0.142" (118 mils or 10 ga.)
410 Stainless-Steel Wafer Head Self-Drilling
Size
Length
Head
Diameter
Carton
Count
#8
1 5⁄8"
.390"
100
F08T162WDC
#8
1 5⁄8"
.390"
1000
F08T162WDM
#8
1 5⁄8"
.390"
3000
F08T162WDB
#8
1
2 ⁄4 "
.390"
100
F08T225WDC
#8
2 1⁄4"
.390"
1000
F08T225WDM
#8
2 1⁄4"
.390"
2500
F08T225WDB
Item No.
Type 410 stainless steel can be hardened through heat treatment, giving it the ability to drill through metal.
It does not offer the same level of corrosion resistance or either type 305 or 316 stainless steel.
HAND-DRIVE SCREWS | Billy Goats™, Self Drilling, Trim Head, Metal Stud
Attach wood siding, wood panels and metal trim to steel studs
#1 square drive trim head, .230" head diameter, #3 drill point
Threaded 2⁄3 of overall length
410 Stainless-Steel Trim Head Self-Drilling
Size
Length
Approx.
Count per lb.
Carton
Count
Item No.
#7
1 5⁄8"
187
100
F07T162TDC
#7
5
1 ⁄8 "
187
1000
F07T162TDM
#7
1 5⁄8"
187
5000
F07T162TDB
#7
1
2 ⁄4"
132
100
F07T225TDC
#7
2 1⁄4"
132
1000
F07T225TDM
#7
2 1⁄4"
132
4000
F07T225TDB
#7
3"
105
100
F07T300TDC
#7
3"
105
1000
F07T300TDM
#7
3"
105
2000
F07T300TDB
38
•
•
•
•
SIDING
Hand-Drive Screws
HAND-DRIVE SCREWS | Twin-Lead Hex-Washer Head
• Fasten aluminum agricultural siding panels to wood joists
without pre-drilling
• Extra-sharp point for quick penetration of aluminum panels without “point walking”
• Twin-lead thread fastens one to three panel thicknesses securely to wood substrate
• 5⁄16" Hex drive
• Panel screws available with and without aluminum/neoprene bonded sealing washers
18-8 and 316 Stainless Steel
Size
Length
Carton
Count
Item No.
Available
in 316*
#9
1"
100
S09T100HWHC
#9
1"
1000
S09T100HWHM
#9
1 1⁄2"
100
S09T150HWHC
#9
1
1 ⁄2"
1000
S09T150HWHM
#9
2"
100
S09T200HWHC
#9
2"
1000
S09T200HWHM
#9
2 1⁄2"
100
S09T250HWHC
—
#9
2 ⁄2"
1000
S09T250HWHM
—
#9
3"
100
S09T300HWHC
—
#9
3"
1000
S09T300HWHM
—
1
18-8 and 316 Stainless Steel with Neoprene-Bonded Washer
Carton
Count
Length
#9
1"
100
S09100HWAC
#9
1"
1000
S09100HWAM
#9
1 1⁄2"
100
S09150HWAC
#9
1 1⁄2"
1000
S09150HWAM
#9
2"
100
S09200HWAC
#9
2"
1000
S09200HWAM
#9
2 1⁄2"
100
S09250HWAC
—
#9
1
2 ⁄2 "
1000
S09250HWAM
—
#9
3"
100
S09300HWAC
—
#9
3"
1000
S09300HWAM
—
Item No.
Available
in 316*
Size
Also available with
neoprene-bonded
washers
39
SIDING
Hand-Drive Screws
HAND-DRIVE SCREWS | K-Lath Modified Truss Head, Self-Drilling
•
•
•
•
•
Fastens corrugated siding panels to steel stud without pre-drilling
#3 drill point for quick penetration of aluminum panels without “point walking”
Securely fastens one to three panel thicknesses
#2 Phillips drive
410 Stainless Steel
Size
Length
Carton
Count
Item No.
⁄16 "
100
F08T056KDC
⁄16 "
1000
F08T056KDM
⁄16 "
8000
F08T056KDB
⁄4"
100
F08T075KDC
⁄4"
1000
F08T075KDM
⁄4"
6000
F08T075KDB
#8
9
#8
9
#8
9
#8
3
#8
3
#8
3
#8
1
1 ⁄4"
100
F08T125KDC
#8
1 1⁄4"
1000
F08T125KDM
#8
1 1⁄4"
4000
F08T125KDB
#8
5
1 ⁄8"
100
F08T162KDC
#8
1 5⁄8"
1000
F08T162KDM
#8
1 5⁄8"
3000
F08T162KDB
#8
2"
100
F08T200KDC
#8
2"
1000
F08T200KDM
#8
2"
2500
F08T200KDB
HAND-DRIVE SCREWS | K-Lath Modified Truss Head, Wood
• For use in applications where a larger bearing
surface is needed underneath the head
• Used to fasten lath to wood
• #2 Phillips drive
305 Stainless Steel
Size
40
Length
Carton
Count
Item No.
⁄4"
100
S08C075KQC
⁄4"
1000
S08C075KQM
#8
3
#8
3
#8
1 1⁄4"
100
S08C125KQC
#8
1 1⁄4"
1000
S08C125KQM
SIDING
Collated Staples
COLLATED STAPLES | Similar to Senco® “N” Series
304 and 316 Stainless Steel, 7/16" Crown
Gauge
Length
Carton
Count
Item No.
Available
in 316*
**
⁄4"
5000
T16N075N11
16
1"
5000
S16N100N13
16
1 1⁄4"
5000
S16N125N15
16
1 1⁄2"
5000
S16N150N17
16
1 3⁄4"
5000
S16N175N19
16
2"
5000
S16N200N21
16
3
Bostitch ®
Hitachi ®
Fasco ®
Max®
Porter Cable ®
Senco ®
650S5
N5008AA & A1, N5008AB & N5008AC
G
TA551/16-11 (1" to 2")
CMS200 & MS200
M1 ( 3⁄4" -1 3⁄4"), SNS45 (1" -2"), SNS50 (1 1⁄4" -2"), SKS ( 3⁄4" to 1 1⁄2" ),
M2+ (1 1⁄4" to 2"), SNS45 (1" to 2")
COLLATED STAPLES | Similar to Paslode® “GS” Series
Gauge
Length
Carton
Count
Item No.
16
1 1⁄4"
10,000
S16N125GS
16
1
1 ⁄2"
10,000
S16N150GS
16
1 3⁄4"
10,000
S16N175GS
Available
in 316*
Fasco ®
Paslode ®
GS
IM200-S16, 4200-S16 & 3200-S16P, 3150-S16 ( 3⁄4" to 1 1⁄2")
41
SIDING
Collated Staples
COLLATED STAPLES | Similar to Paslode® “GSI” Series
304 Stainless Steel, 7/16" Crown
Carton
Count
Gauge
Length
Item No.
16
1 1⁄4"
10,000
S16N125GSI
16
1 1⁄2"
10,000
S16N150GSI
DuoFast ®
Paslode ®
76 Series Stapler (1 1⁄4" -1 1⁄2")
3200-I16 (1 1⁄4" -1 1⁄2"), 3150-I16 (1 1⁄4" -1 1⁄2"), MU112-I16 (1 1⁄4")
COLLATED STAPLES | Similar to Bostitch® “BCS” Series
Gauge
Length
Carton
Count
Item No.
16
1 1⁄4"
10,000
T16N125B07
16
1
1 ⁄2"
10,000
T16N150B09
16
1 3⁄4"
10,000
T16N175B11
16
2"
10,000
T16N200B13
Bostitch ®
Fasco ®
42
T36-1, T36-50, T50S4-1 & T55S4-1 ( 3⁄4" -1 3⁄4"), 438S2R (1⁄2" -1 1⁄2"),
T40S4-CT ( 3⁄4" to 1 1⁄2") , 438S4, 650S4
HD
ROOFING
ROOFING
Slate
Choose from our selection of hand-drive stainless-steel or copper roofing nails when
fastening this natural stone material that has been used for centuries to provide long
lasting elegant beauty and stability.
Composite Slate
Today’s synthetic slate offers the appeal of real slate in terms of color, texture, light
weight and long service. Our stainless-steel hand-drive and collated roofing nails are
your best bet for fastening this type of roofing.
Wood Shingle
If you’re roofing with cedar or pressure treated pine, you’ll find our stainless-steel
hand-drive shake/shingle nails to be your best option for the job. They’re also available
in a wire coil collated configuration, compatible with a variety of pneumatic nail guns.
Standing Seam and Corrugated Panel
We offer low-profile pancake head screws specifically designed for fastening standing
seam roofing to either wood stud or metal stud. Look to our twin-lead thread, hex head
screws for aluminum and fiberglass corrugated panel installation.
Hand-Drive Nails
Simpson Strong-Tie offers a wide array of Swan
Secure hand-drive and collated nails, screws,
and staples for fastening roofing materials of
all types. Whether it’s slate, asphalt shingle,
tile, cedar shake, standing seam copper or
corrugated roofing, we’ve got you covered.
Slate
Roofing/Slating, Copper ............................................... 44
Roofing/Slating, Stainless ............................................ 45
Roofing/Slating, Aluminum........................................... 45
Shake and Shingle ........................................................ 46
Washered Roofing, Stainless ........................................ 46
Tile/Slate, Copper ...........................................................47
Tile/Slate, Stainless ....................................................... 48
Gutter Spikes................................................................. 48
Collated Nails
Composite Slate
Wire-Coil Collated, Roofing .......................................... 49
Collated Staples
Similar To:
Senco ® “L” Series.......................................................... 50
Senco ® “N” Series......................................................... 50
Senco ® “P” Series ..........................................................51
Paslode ® “GS” Series .....................................................51
Bostitch® “BCS” Series ..................................................51
Wood Shingle
Standing Seam
Corrugated Panel
Hand-Drive Screws
Truss Head, Self-Drilling................................................ 52
Hex Washer Panel ......................................................... 52
Pancake/Clip, Square Drive, Self-Drilling ..................... 53
Pancake/Clip, Square Drive, Type “A” Point ................. 53
Gutter Screws, Hex Socket Drive .................................. 53
43
ROOFING
Hand-Drive Nails
HAND-DRIVE NAILS | Roofing/Slating, Copper
•
•
•
•
•
Large flat head, regular diamond point
Copper roofing nails are also commonly referred to as slating nails
Annular ring shank nails offer superior holding power in plywood roof decks
For slate roofs choose nail length by adding one inch to twice the thickness of slate
Bucket = 25 lbs.
Annular Ring Shank Copper
Length
Gauge
Shank
Diameter
⁄4"
11
.120"
3
1"
10
.134"
7
1"
11
.120"
3
1
1 ⁄4"
10
.134"
7
1 1⁄4"
11
.120"
3
1
1 ⁄2"
10
.134"
7
1 1⁄2"
11
.120"
3
3
1 ⁄4"
10
.134"
7
3
1 ⁄4"
11
.120"
3
2"
10
.134"
7
2"
11
.120"
3
2 1⁄2"
10
.134"
7
2 1⁄2"
11
.120"
3
3"
10
.134"
7
3
Head
Diameter
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
Bucket
Item No.
⁄8"
302
C7511ARN25
C7511ARN5
C7511ARN1
C7511ARNB
⁄16 "
187
C210ARN25
C210ARN5
C210ARN1
C210ARNB
⁄8"
229
C211ARN25
C211ARN5
C211ARN1
C211ARNB
⁄16 "
147
C310ARN25
C310ARN5
C310ARN1
C310ARNB
⁄8"
187
C311ARN25
C311ARN5
C311ARN1
C311ARNB
⁄16 "
123
C410ARN25
C410ARN5
C410ARN1
C410ARNB
⁄8"
155
C411ARN25
C411ARN5
C411ARN1
C411ARNB
⁄16 "
112
C510ARN25
C510ARN5
C510ARN1
C510ARNB
⁄8"
139
C511ARN25
C511ARN5
C511ARN1
C511ARNB
⁄16 "
93
C610ARN25
C610ARN5
C610ARN1
C610ARNB
⁄8"
124
C611ARN25
C611ARN5
C611ARN1
C611ARNB
⁄16 "
81
C810ARN25
C810ARN5
C810ARN1
C810ARNB
⁄8"
108
C811ARN25
C811ARN5
C811ARN1
C811ARNB
⁄16 "
67
C1010ARN25
C1010ARN5
C1010ARN1
C1010ARNB
Head
Diameter
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
Bucket
Item No.
Length
Gauge
Shank
Diameter
⁄4"
11
.120"
3
1"
10
.134"
7
1"
11
.120"
3
1
1 ⁄4"
10
.134"
7
1 1⁄4"
11
.120"
3
1
1 ⁄2"
10
.134"
7
1 1⁄2"
11
.120"
3
3
1 ⁄4"
10
.134"
7
3
1 ⁄4"
11
.120"
3
2"
10
.134"
7
2"
11
.120"
3
2 1⁄2"
10
.134"
7
2 1⁄2"
11
.120"
3
3"
10
.134"
7
3
44
⁄8"
302
C7511RN25
C7511RN5
C7511RN1
C7511RNB
⁄16 "
187
C210RN25
C210RN5
C210RN1
C210RNB
⁄8"
229
C211RN25
C211RN5
C211RN1
C211RNB
⁄16 "
147
C310RN25
C310RN5
C310RN1
C310RNB
⁄8"
187
C311RN25
C311RN5
C311RN1
C311RNB
⁄16 "
123
C410RN25
C410RN5
C410RN1
C410RNB
⁄8"
155
C411RN25
C411RN5
C411RN1
C411RNB
⁄16 "
112
C510RN25
C510RN5
C510RN1
C510RNB
⁄8"
139
C511RN25
C511RN5
C511RN1
C511RNB
⁄16 "
93
C610RN25
C610RN5
C610RN1
C610RNB
⁄8"
124
C611RN25
C611RN5
C611RN1
C611RNB
⁄16 "
81
C810RN25
C810RN5
C810RN1
C810RNB
⁄8"
108
C811RN25
C811RN5
C811RN1
C811RNB
⁄16 "
67
C1010RN25
C1010RN5
C1010RN1
C1010RNB
Smooth Shank Copper
ROOFING
Hand-Drive Nails
HAND-DRIVE NAILS | Roofing/Slating, Stainless Steel
•
•
•
•
•
Annular ring shank nails offer superior holding power in wood and plywood roof decks
For slate roofs choose nail length by adding one inch to twice the thickness of slate
Smooth shank available – when ordering, remove “A” from listed part numbers below
Bucket = 25 lbs.
304 and 316 Stainless Steel, Annular Ring Shank
Length
Gauge
Shank
Diameter
⁄4"
10
.134"
3
1"
10
.134"
3
1
1 ⁄4"
10
.134"
3
1 1⁄4"
11
.120"
11
1
1 ⁄2"
10
.134"
3
1 1⁄2"
11
.120"
11
3
1 ⁄4"
10
.134"
3
3
1 ⁄4"
11
.120"
11
2"
10
.134"
3
2"
11
.120"
11
2 1⁄2"
10
.134"
3
3"
10
.134"
3
3
Head
Diameter
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
Bucket
Item No.
⁄8"
281
S7510ARN25
S7510ARN5
S7510ARN1
S7510ARNB
⁄8"
212
S210ARN25
S210ARN5
S210ARN1
S210ARNB
⁄8"
166
S310ARN25
S310ARN5
S310ARN1
S310ARNB
⁄32"
199
S311ARN25
S311ARN5
S311ARN1
S311ARNB
⁄8"
139
S410ARN25
S410ARN5
S410ARN1
S410ARNB
⁄32"
170
S411ARN25
S411ARN5
S411ARN1
S411ARNB
⁄8"
126
S510ARN25
S510ARN5
S510ARN1
S510ARNB
⁄32"
149
S511ARN25
S511ARN5
S511ARN1
S511ARNB
⁄8"
105
S610ARN25
S610ARN5
S610ARN1
S610ARNB
⁄32"
136
S611ARN25
S611ARN5
S611ARN1
S611ARNB
⁄8"
91
S810ARN25
S810ARN5
S810ARN1
S810ARNB
⁄8"
78
S1010ARN25
S1010ARN5
S1010ARN1
S1010ARNB
Available
in 316*
HAND-DRIVE NAILS | Roofing/Slating, Aluminum
• Large flat head, regular diamond point
• Spiral shank available upon request – call for details
Aluminum, Annular Ring Shank
Length
Gauge
Shank
Diameter
Head
Diameter
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
1"
11
.120"
3
1 1⁄4"
11
.120"
3
⁄8"
810
A211ARN25
A211ARN5
A211ARN1
⁄8"
686
A311ARN25
A311ARN5
1
1 ⁄2"
11
.120"
3
A311ARN1
1 1⁄4"
9
.148"
7
1
1 ⁄2"
9
.148"
7
2"
9
.148"
7
⁄8"
577
A411ARN25
A411ARN5
A411ARN1
⁄16 "
440
A39ARN25
A39ARN5
A39ARN1
⁄16 "
374
A49ARN25
A49ARN5
A49ARN1
⁄16 "
288
A69ARN25
A69ARN5
A69ARN1
Head
Diameter
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
⁄8"
810
A211RN25
A211RN5
A211RN1
⁄8"
686
A311RN25
A311RN5
A311RN1
⁄8"
577
A411RN25
A411RN5
A411RN1
⁄16 "
440
A39RN25
A39RN5
A39RN1
⁄16 "
374
A49RN25
A49RN5
A49RN1
⁄16 "
288
A69RN25
A69RN5
A69RN1
Aluminum, Smooth Shank
Length
Gauge
Shank
Diameter
1"
11
.120"
3
1
1 ⁄4"
11
.120"
3
1 1⁄2"
11
.120"
3
1
1 ⁄4"
9
.148"
7
1 1⁄2"
9
.148"
7
2"
9
.148"
7
We are proud of the fact that
our nails were chosen to
install the slate roofing at the
University of Notre Dame.
45
ROOFING
Hand-Drive Nails
HAND-DRIVE NAILS | Shake and Shingle
• 7⁄32" diameter checker-patterned flat head provides ample bearing surface
to firmly secure shakes and shingles of all types
• Slender shanks minimize splitting
• Annular ring threads insure against wind damage and nail-head popping
Penny
Size
Length
Gauge
Shank
Diameter
3d
1 1⁄4"
14
.083"
7
4d
1 1⁄2"
14
.083"
7
5d
1 3⁄4"
14
.083"
7
6d
2"
13
.095"
7
7d
2 1⁄4"
13
.095"
7
8d
2 ⁄2"
13
.095"
7
1
Head
Diameter
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
Bucket
Item No.
⁄32"
470
S3SN725
S3SN75
S3SN71
S3SN7B
⁄32"
394
S4SN725
S4SN75
S4SN71
S4SN7B
⁄32"
337
S5SN725
S5SN75
S5SN71
S5SN7B
⁄32"
237
S6SN725
S6SN75
S6SN71
S6SN7B
⁄32"
216
S7SN725
S7SN75
S7SN71
S7SN7B
⁄32"
196
S8SN725
S8SN75
S8SN71
S8SN7B
Available
in 316*
HAND-DRIVE NAILS | Washered Roofing
•
•
•
•
•
Annular ring thread, large checkered head, heavy EPDM washers assembled
Best for application of corrugated panel roofing, particularly in corrosive environments
Also the recommended fastener for sheet metal roofing and siding
Standard washer dimensions: 9⁄16" O.D. x 1⁄8" thick
Large, resilient EPDM washers provide weather-tight fastening
46
Shank
Head
Approx.
Diameter Diameter Count per lb.
Length
Gauge
1¼"
10
.134"
3
1½"
10
.134"
3
1¾"
10
.134"
3
2"
10
.134"
3
2¼"
10
.134"
3
2½"
10
.134"
3
3"
10
.134"
3
3½"
10
.134"
3
4"
10
.134"
3
25 lb.
Item No.
5 lb.
Item No.
⁄8"
121
S10125RNW25
S10125RNW5
⁄8"
113
S10150RNW25
S10150RNW5
⁄8"
105
S10175RNW25
S10175RNW5
⁄8"
98
S10200RNW25
S10200RNW5
⁄8"
91
S10225RNW25
S10225RNW5
⁄8"
83
S10250RNW25
S10250RNW5
⁄8"
72
S10300RNW25
S10300RNW5
⁄8"
62
S10350RNW25
S10350RNW5
⁄8"
53
S10400RNW25
S10400RNW5
Annular Ring Shank 304 Stainless Steel
ROOFING
Hand-Drive Nails
HAND-DRIVE NAILS | Tile/Slate, Copper
• Large flat head, diamond point
• Annular ring threads offer greater pull-out resistance
• Long nails expressly for installing curved Spanish roof tiles and slate
Annular Ring Shank Copper
Length
Gauge
Shank
Diameter
Head
Diameter
3"
9
.148"
15
1
3 ⁄2"
10
.134"
7
3 1⁄2"
9
.148"
15
4"
9
.148"
15
5"
8
.165"
1
5 1⁄2"
8
.165"
1
6"
8
.165"
1
⁄32"
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
57
C10ATN25
C10ATN5
⁄16 "
59
C16ATN25
C16ATN5
⁄32"
48
C16HATN25
C16HATN5
⁄32"
43
C20ATN25
C20ATN5
⁄2"
28
C40ATN25
C40ATN5
⁄2"
25
C50ATN25
C50ATN5
⁄2"
23
C60ATN25
C60ATN5
Smooth Shank Copper
Length
Gauge
Shank
Diameter
Head
Diameter
3"
9
.148"
15
1
3 ⁄2"
10
.134"
7
3 1⁄2"
9
.148"
15
4"
9
.148"
15
⁄32"
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
57
C10TN25
C10TN5
⁄16 "
59
C16TN25
C16TN5
⁄32"
48
C16HTN25
C16HTN5
⁄32"
43
C20TN25
C20TN5
⁄2"
28
C40TN25
C40TN5
⁄2"
25
C50TN25
C50TN5
⁄2"
23
C60TN25
C60TN5
8
.165"
5 1⁄2"
8
.165"
1
6"
8
.165"
1
Copper slating nails are the
roofer’s fastener of choice when
it comes to slate roof repair.
When a slate needs replacement,
the roofer uses a slate ripper
which is a tool that cuts the nails
so that the broken slate can then
be removed. Copper nails, being
softer than stainless steel are
much easier to cut.
5"
1
!
We are proud to have contributed to the post-9/11 Pentagon re-roofing by donating copper slating nails
to Meyers Roofing through our relationship with the National Roofing Contractor’s Association.
47
ROOFING
Hand-Drive Nails
HAND-DRIVE NAILS | Tile/Slate, Stainless Steel
•
•
•
•
Long nails expressly for installing curved Spanish roof tiles and slate
Large flat head, smooth shank, diamond point
Annular ring threads offer greater pull-out resistance
Available in 316 stainless steel – call for details
Annular Ring Shank 304 Stainless Steel
Length
Gauge
Shank
Diameter
Head
Diameter
3"
9
.148"
15
3 1⁄2"
10
.134"
7
3 1⁄2"
9
.148"
15
4"
9
.148"
15
5"
8
.165"
1
1
5 ⁄2"
8
.165"
1
6"
8
.165"
1
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
⁄32"
57
S10ATN25
S10ATN5
⁄16 "
59
S16ATN25
S16ATN5
⁄32"
48
S16HATN25
S16HATN5
⁄32"
43
S20ATN25
S20ATN5
⁄2"
28
S40ATN25
S40ATN5
⁄2"
25
S50ATN25
S50ATN5
⁄2"
23
S60ATN25
S60ATN5
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
57
S10TN25
S10TN5
Length
Gauge
Shank
Diameter
Head
Diameter
3"
9
.148"
15
1
3 ⁄2"
10
.134"
7
3 1⁄2"
9
.148"
15
4"
9
.148"
15
5"
8
.165"
1
5 1⁄2"
8
.165"
1
6"
8
.165"
1
⁄32"
⁄16 "
59
S16TN25
S16TN5
⁄32"
48
S16HTN25
S16HTN5
⁄32"
43
S20TN25
S20TN5
⁄2"
28
S40TN25
S40TN5
⁄2"
25
S50TN25
S50TN5
⁄2"
23
S60TN25
S60TN5
HAND-DRIVE NAILS | Gutter Spikes
• Dimpled flat head, barbed shank, diamond point
• Stainless steel available in select sizes - call for availablity
Copper
48
Length
Shank
Diameter
Head
Diameter
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
7"
.238"
15
8"
.238"
15
⁄32"
10
C7S25
C7S5
9"
.238"
15
⁄32"
9
C8S25
C8S5
10"
.238"
15
⁄32"
8
C9S25
C9S5
⁄32"
6
C10S25
C10S5
Smooth Shank 304 Stainless Steel
ROOFING
Collated Nails
COLLATED NAILS | Roofing, Wire Coil 15°
•
•
•
•
Great for asphalt and synthetic slate roofing
304 Stainless Steel, Ring Shank
Length
Shank
Diameter
Head
Diameter
Box
Count
Item No.
1"
.120"
3
1
1 ⁄4"
.120"
3
⁄8"
7200
S11A100RNB
⁄8"
7200
1
1 ⁄4"
.120"
3
S11A125RNB
1 1⁄2"
.120"
3
1 1⁄2"
.120"
3
3
1 ⁄4"
.120"
3
1 3⁄4"
.120"
3
⁄8"
2400
S11A125RNJ
⁄8"
7200
S11A150RNB
⁄8"
2400
S11A150RNJ
⁄8"
7200
S11A175RNB
⁄8"
2400
S11A175RNJ
Head
Diameter
Box
Count
Item No.
⁄8"
3600
T11A100RNJ
⁄8"
3600
T11A125RNJ
⁄8"
3600
T11A150RNJ
⁄8"
3600
T11A175RNJ
Bostitch ®
Head
Diameter
Box
Count
Item No.
⁄8"
7200
S11N075RNB
⁄8"
7200
S11N087RNB
⁄8"
7200
S11N100RNB
316 Stainless Steel, Ring Shank
Length
Shank
Diameter
1"
.120"
3
1
1 ⁄4"
.120"
3
1
1 ⁄2"
.120"
3
1 3⁄4"
.120"
3
304 Stainless Steel, Smooth Shank
Length
Shank
Diameter
⁄4"
.120"
3
⁄8"
.120"
3
1"
.120"
3
3
7
1"
.120"
3
1 1⁄4"
.120"
3
⁄8"
2400
S11N100RNJ
⁄8"
7200
S11N125RNB
1 1⁄4"
.120"
3
1 1⁄2"
.120"
3
1 1⁄2"
.120"
3
3
1 ⁄4"
.120"
3
1 3⁄4"
.120"
3
⁄8"
2400
S11N125RNJ
⁄8"
7200
S11N150RNB
⁄8"
2400
S11N150RNJ
⁄8"
7200
S11N175RNB
⁄8"
2400
S11N175RNJ
Head
Diameter
Box
Count
Item No.
⁄8"
3600
T11N100RNJ
⁄8"
3600
T11N125RNJ
⁄8"
3600
T11N150RNJ
⁄8"
3600
T11N175RNJ
N12-1 (1 1⁄4" to 1 3⁄4"),
N12B, RN45B, RN46
Craftsman ® 18455
Hitachi ®
NV45AB , NV45AB2
Makita ®
AN451
MAX ®
CN450R, CN12R
Paslode ®
3175RCU, 3175/44 RCU
Porter Cable ® 134R & RN175
Senco ®
SCN200R & SCN40R
( 3⁄4" to 1 1⁄2")
Stan-Tech ® SDCN10-1
316 Stainless Steel, Smooth Shank
Length
Shank
Diameter
1"
.120"
3
1 1⁄4"
.120"
3
1
1 ⁄2"
.120"
3
1 ⁄4"
.120"
3
3
49
ROOFING
Collated Staples
COLLATED STAPLES | Similar to Senco® “L” Series
Gauge
Length
Carton
Count
Item No.
⁄8"
5000
S18N062L10
18
5
18
3
⁄4"
5000
T18N075L11
18
1"
5000
S18N100L13
18
1 1⁄8"
5000
S18N112L14
18
1
1 ⁄4"
5000
S18N125L15
18
1 1⁄2"
5000
S18N150L17
Available
in 316*
**
Duo-Fast ®
Grizzly®
Haubold ®
Hilti ®
Hitachi ®
Porter Cable ®
Senco ®
KN-1848A
G6043
PN6040H
SN-114B, SN-118
N3804A, N3804AA & N3804AB
NS100 (1⁄2" to 1") NS150 (1⁄2" to 1 1⁄2")
FinishPro 2N1 (1⁄4" -1"), SLS15 ( 5⁄8" to 1"), SLS18 (1⁄2" to 1 1⁄2"), SLS20,
SLS25XP ( 3⁄8" to 1 1⁄2"), SKSL12-17 (7⁄8" to 1 1⁄2"), SKSL11-15 ( 3⁄4" to 1 1⁄4")
Gauge
Length
Carton
Count
Item No.
Available
in 316*
**
⁄4"
5000
T16N075N11
16
1"
5000
S16N100N13
16
1 1⁄4"
5000
S16N125N15
16
1
1 ⁄2"
5000
S16N150N17
16
1 3⁄4"
5000
S16N175N19
16
2"
5000
S16N200N21
16
3
Bostitch ®
Hitachi ®
Fasco ®
Max®
Porter Cable ®
Senco ®
50
650S5
N5008AA & A1, N5008AB & N5008AC
G
TA551/16-11 (1" to 2")
CMS200 & MS200
M1 ( 3⁄4" -1 3⁄4"), SNS45 (1" -2"), SNS50 (1 1⁄4" -2"), SKS ( 3⁄4" to 1 1⁄2" ),
M2+ (1 1⁄4" to 2" ), SNS45 (1" to 2")
ROOFING
Collated Staples
COLLATED STAPLES | Similar to Senco® “P” Series
304 and 316 Stainless Steel, 1" Crown
Length
Carton
Count
Item No.
⁄4"
5000
S16N075P51
16
1"
5000
S16N100P53
16
1 1⁄4"
5000
S16N125P55
Gauge
16
3
Available
in 316*
Hitachi ® N3824A (1⁄2" to 1 1⁄2") N5024A
Senco ® PW ( 3⁄4" -1 1⁄4") & MW ( 3⁄4" to 1 1⁄2"), SPS ( 3⁄4" to 1 1⁄2") & PW2 (1" to 2")
Carton
Count
Available
in 316*
Gauge
Length
16
1 1⁄4"
10,000
S16N125GS
16
1 1⁄2"
10,000
S16N150GS
16
1 3⁄4"
10,000
S16N175GS
16
2"
10,000
S16N200GS
Item No.
Fasco ®
GS
Paslode ® IM200-S16, 4200-S16 & 3200-S16P, 3150-S16 ( 3⁄4" to 1 1⁄2")
Gauge
Length
Carton
Count
Item No.
16
1 1⁄4"
10,000
T16N125B07
16
1
1 ⁄2"
10,000
T16N150B09
16
1 3⁄4"
10,000
T16N175B11
16
2"
10,000
T16N200B13
Bostitch ® T36-1, T36-50, T50S4-1 & T55S4-1 ( 3⁄4" -1 3⁄4"), 438S2R (1⁄2" to 1 1⁄2"),
T40S4-CT ( 3⁄4" to 1 1⁄2"), 438S4, 650S4, 650S4
®
Fasco
HD
51
ROOFING
Hand-Drive Screws
HAND-DRIVE SCREWS | Truss Head, Self-Drilling
•
•
•
•
#3 Phillips truss head, tapping screw thread (13 threads per inch), drill point
Hardened martensitic stainless-steel alloy (14% Chrome, 1% Nickel, 1% Molybdenum)
Secure single-ply membrane through insulation to steel purlins
Factory Mutual approved for fastening to 16–22 gauge steel and wood decking
410 Stainless Steel
Length
Diameter
Thread
Length
Carton
Count
Item No.
1 1⁄2"
.235
Full
20
F14C150T20
1
1 ⁄2 "
.235
Full
100
F14C150TIC
2"
.235
Full
10
F14C200T10
3"
.235
Full
10
F14C300T10
4"
.235
37⁄8"
10
F14C400T10
5"
.235
37⁄8"
10
F14C500T10
7
6"
.235
3 ⁄8"
5
F14C600T5
7"
.235
37⁄8"
5
F14C700T5
7
8"
.235
3 ⁄8"
1
F14C800T1
10"
.235
37⁄8"
1
F14C1000T1
12"
.235
37⁄8"
1
F14C1200T1
•
•
•
•
•
Fasten aluminum agricultural roofing panels to wood joists without pre-drilling
Extra-sharp point for quick penetration of aluminum panels without “point walking”
Twin-lead thread fastens one to three panel thicknesses securely to wood substrate
Panel screws available with and without aluminum/neoprene bonded sealing washers
5
⁄16" Hex drive
18-8 and 316 Stainless Steel
Size
Length
Carton
Count
Item No.
#9
1"
100
S09100HWAC
#9
1"
1000
S09100HWAM
#9
1
1 ⁄2"
100
S09150HWAC
#9
1 1⁄2"
1000
S09150HWAM
#9
2"
100
S09200HWAC
#9
2"
1000
S09200HWAM
#9
2 1⁄2"
100
S09250HWAC
—
#9
1
2 ⁄2"
1000
S09250HWAM
—
#9
3"
100
S09300HWAC
—
#9
3"
1000
S09300HWAM
—
52
Available
in 316*
HAND-DRIVE SCREWS | Twin Lead, Hex-Washer Head
ROOFING
Hand-Drive Screws
HAND-DRIVE SCREWS | Pancake/Clip, Self-Drilling
•
•
•
•
Low-profile head
Ideal for securing clips used in standing seam roofing
#3 drill point for quick penetration of metal up to 0.142" (118 mils. or 10 ga.) material thickness
#2 Square drive
410 Stainless Steel
Size
Length
Carton
Count
Item No.
#10
1"
100
F10T100PSC
#10
1"
1000
F10T100PSM
#10
1"
4500
F10T100PSB
HAND-DRIVE SCREWS | Pancake/Clip, Type A Point
• Low-profile head
• Ideal for securing clips used in standing seam roofing
• #2 Square drive
410 Stainless Steel
Size
Length
Carton
Count
Item No.
#10
1"
100
F10T100PTC
#10
1"
1000
F10T100PTM
#10
1"
4500
F10T100PTB
#10
2"
100
F10T200PTC
#10
2"
1000
F10T200PTM
HAND-DRIVE SCREWS | Gutter Screws
• These longer screws are ideal for fastening rain gutters to wood facia board
• Sold in a kit of 12 screws, 12 aluminum ferrules and a hex driver.
• 3⁄16" Hex socket drive
316 Stainless Steel
Size
Thread
Length
Carton
Count
Item No.
⁄16 " x 7"
3"
12
T31700GS12
5
53
FRAMING
FRAMING
Hand-Drive Nails
Simpson Strong-Tie ® Swan Secure nails meet or exceed today’s toughest standards
for quality and corrosion resistance. Framing, dock construction, and permanent wood
foundations will stand the test of time when our AISI-graded stainless-steel fasteners
are used in their construction. Our hand-driven nails are available in ring shank, smooth
shank and screw shank.
Collated Nails
We distribute a wide selection of collated nails designed for the pneumatic tools you
trust on the job. Choose the appropriate collation to fit your framing gun – we stock plastic
collation, paper tape, and wire weld. Furthermore, we proudly recommend our collated
nails expressly developed for metal-connector nailers used for installing joist hangers
and other structural connectors. They’re available in both paper tape and plastic collation
to fit all the popular tools.
Timber Tamers™
Another of our recently introduced products is the innovative Timber Tamer ™. This
fastener is a big improvement over the lag screw in that it requires no pre-drilling thanks
to its unique four-corner, torque-reducing thread design.
You can count on Simpson
Strong-Tie to deliver the best
combination of long lasting
quality and service when
it comes to stainless-steel
fasteners for framing and
structural applications.
Hand-Drive Nails
Common Ring Shank, Un-Common ™.................................................. 55
Common Smooth Shank, Un-Common ™ ............................................ 55
Post and Beam .................................................................................... 56
Box ...................................................................................................... 56
Structural-Connector .......................................................................... 57
Collated Nails
Plastic Strip 20–22°, Full Round, Ring Shank, Stainless ................... 57
Plastic Strip 20–22°, Full Round, Ring Shank, Bronze ....................... 58
Plastic Strip 20–22°, Full Round, Screw Shank, Stainless ................. 58
Plastic Strip 20–22°, Full Round, Smooth Shank, Stainless ................ 59
Plastic Strip 20–22°, Full Round, Casing Head, Ring Shank, Stainless..59
Wire Weld 28°, Clipped Head, Ring Shank, Stainless ......................... 59
Wire Coil 15°, Ring Shank ................................................................... 60
Paper Tape 31–34°, Structural-Connector.......................................... 60
Plastic Strip 31–34°, Full Round, Ring Shank .................................... 61
Paper Tape 31–34°, Clipped Head, Ring Shank .................................. 61
Hand-Drive Screws
Hex-Washer Head, Timber Tamers ™ ................................................... 62
Hex-Washer Head, Strong-Drive ® ....................................................... 63
54
Un-Common ™ Common Smooth Shank ............................................. 57
FRAMING
Hand-Drive Nails
HAND-DRIVE NAILS | Un-Common™ Common Ring Shank and Smooth Shank
• General-purpose nails with the heft to penetrate even the toughest seasoned timber
• Recommended first choice for construction of permanent wood foundations by
the ANSI/AF&PA Permanent Wood Foundations Design Specifications
• Specify annular ring threads provide greater pull-out resistance
• Also available in screw shank – call for details
304 and 316 Stainless Steel, Ring Shank
Penny
Size
Length
Gauge
Shank
Diameter
2d
1"
15
.072"
3
3d
1
1 ⁄4"
14
.083"
7
4d
1 1⁄2"
12
.109"
1
5d
1 3⁄4"
12
.109"
1
6d
2"
11
.120"
17
7d
2 1⁄4"
11
.120"
17
8d
1
2 ⁄2 "
10
.134"
9
10d
3"
9
.148"
5
12d
3 1⁄4"
9
.148"
5
16d
3 1⁄2"
8
.165"
11
20d
4"
6
.203"
7
30d
1
4 ⁄2 "
6
.203"
7
40d
5"
6
.203"
7
60d
6"
4
.238"
15
70d
7"
4
.238"
15
Head
Diameter
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
Bucket
Item No.
⁄16 "
807
S2ACN25
S2ACN5
S2ACN1
S2ACNB
⁄32"
473
S3ACN25
S3ACN5
S3ACN1
S3ACNB
⁄4"
228
S4ACN25
S4ACN5
S4ACN1
S4ACNB
⁄4"
193
S5ACN25
S5ACN5
S5ACN1
S5ACNB
⁄64"
144
S6ACN25
S6ACN5
S6ACN1
S6ACNB
⁄64"
133
S7ACN25
S7ACN5
S7ACN1
S7ACNB
⁄32"
94
S8ACN25
S8ACN5
S8ACN1
S8ACNB
⁄16 "
67
S10ACN25
S10ACN5
S10ACN1
S10ACNB
⁄16 "
60
S12ACN25
S12ACN5
S12ACN1
S12ACNB
⁄32"
44
S16ACN25
S16ACN5
S16ACN1
S16ACNB
⁄16 "
25
S20ACN25
S20ACN5
S20ACN1
S20ACNB
⁄16 "
22
S30ACN25
S30ACN5
S30ACN1
—
⁄16 "
19
S40ACN25
S40ACN5
S40ACN1
S40ACNB
⁄32"
12
S60ACN25
S60ACN5
S60ACN1
—
⁄32"
10
S70ACN25
S70ACN5
S70ACN1
—
1 lb.
Item No.
Bucket
Item No.
Available
in 316*
304 and 316 Stainless Steel, Smooth Shank
Penny
Size
Length
Gauge
Shank
Diameter
Head
Diameter
Approx.
Count per lb.
2d
1"
15
.072"
3
3d
1 1⁄4"
14
.083"
7
4d
1 1⁄2"
12
.109"
1
5d
1 3⁄4"
12
.109"
1
6d
2"
11
.120"
17
7d
1
2 ⁄4"
11
.120"
17
8d
2 1⁄2"
10
.134"
9
10d
3"
9
.148
5
12d
3 1⁄4"
9
.148"
5
16d
1
3 ⁄2 "
8
.165"
11
5 lb.
Item No.
⁄16 "
807
S2CN25
S2CN5
S2CN1
S2CNB
⁄32"
473
S3CN25
S3CN5
S3CN1
S3CNB
⁄4"
228
S4CN25
S4CN5
S4CN1
S4CNB
⁄4"
193
S5CN25
S5CN5
S5CN1
S5CNB
⁄64"
144
S6CN25
S6CN5
S6CN1
S6CNB
⁄64"
133
S7CN25
S7CN5
S7CN1
S7CNB
⁄32"
94
S8CN25
S8CN5
S8CN1
S8CNB
⁄16 "
67
S10CN25
S10CN5
S10CN1
S10CNB
⁄16 "
60
S12CN25
S12CN5
S12CN1
S12CNB
⁄32"
44
S16CN25
S16CN5
S16CN1
S16CNB
20d
4"
6
.203"
7
30d
4 1⁄2"
6
.203"
7
40d
5"
6
.203"
7
60d
6"
4
.238"
15
70d
7"
4
.238"
15
25 lb.
Item No.
⁄16 "
25
S20CN25
S20CN5
S20CN1
—
⁄16 "
22
S30CN25
S30CN5
S30CN1
—
⁄16 "
19
S40CN25
S40CN5
S40CN1
—
⁄32"
12
S60CN25
S60CN5
S60CN1
—
⁄32"
10
S70CN25
S70CN5
S70CN1
—
Available
in 316*
55
FRAMING
Hand-Drive Nails
HAND-DRIVE NAILS | Post and Beam, Ring Shank
• Slightly lighter gauge than our “Un-Commons,” our Post & Beam nails are
easily driven with minimum splitting
• Favored for cooling tower construction, repair and upgrade, these nails are ideal
for either fir or redwood construction
• Use longer lengths for framing jobs using preservative-treated structural members
• Screw shank available – call for details
• Also available in silicon bronze – contact Simpson Strong-Tie for details
Penny
Size
Length
Gauge
Shank
Diameter
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
6d
2"
12
.109"
17
8d
1
2 ⁄2"
11
.120"
17
⁄64"
175
S6APB25
S6APB5
S6APB1
10d
3"
10
.134"
9
⁄64"
115
S8APB25
S8APB5
S8APB1
⁄32"
79
S10APB25
S10APB5
S10APB1
12d
3 1⁄4"
10
.134"
9
16d
3 1⁄2"
9
.148"
5
⁄32"
72
S12APB25
S12APB5
S12APB1
⁄16 "
56
S16APB25
S16APB5
S16APB1
.165"
11
20d
4"
8
30d
1
⁄32"
40
S20APB25
S20APB5
S20APB1
8
.165"
11
4 ⁄2"
40d
5"
⁄32"
35
S30APB25
S30APB5
S30APB1
8
.165"
11
⁄32"
31
S40APB25
S40APB5
S40APB1
60d
6"
6
.203"
7
70d
⁄32"
17
S60APB25
S60APB5
S60APB1
7"
4
.238"
15
⁄32"
10
S70APB25
S70APB5
S70APB1
*For sizes available in 316 stainless steel(
Head
Diameter
Available
in 316*
•
•
•
•
•
•
Slender shank minimizes wood splitting
Checkered flat head diffracts sunlight and accepts surface finishes
Recommended for hardboard siding materials
Screw shank available – call for details
Penny
Size
Length
Gauge
Shank
Diameter
3d
1 1⁄4"
14
.083"
7
4d
1
1 ⁄2"
14
.083"
7
5d
3
1 ⁄4"
13
.095"
13
6d
2"
12
.109"
17
7d
2 1⁄4"
12
.109"
17
8d
2 1⁄2"
12
.109"
17
10d
3"
11
.120"
17
12d
1
3 ⁄4"
10
.134"
9
16d
3 1⁄2"
10
.134"
9
20d
4"
8
.165"
11
*For sizes available in 316 stainless steel(
56
Head
Diameter
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
⁄32"
473
S3ABN25
S3ABN5
S3ABN1
⁄32"
413
S4ABN25
S4ABN5
S4ABN1
⁄64"
260
S5ABN25
S5ABN5
S5ABN1
⁄64"
175
S6ABN25
S6ABN5
S6ABN1
⁄64"
153
S7ABN25
S7ABN5
S7ABN1
⁄64"
138
S8ABN25
S8ABN5
S8ABN1
⁄64"
99
S10ABN25
S10ABN5
S10ABN1
⁄32"
72
S12ABN25
S12ABN5
S12ABN1
⁄32"
67
S16ABN25
S16ABN5
S16ABN1
⁄32"
40
S20ABN25
S20ABN5
S20ABN1
Available
in 316*
HAND-DRIVE NAILS | Box, Ring Shank
FRAMING
Hand-Drive Nails / Collated Nails
HAND-DRIVE NAILS | Structural Connectors, Smooth Shank
• For installation of joist hangers, structural connectors and hurricane clips in corrosive environments
• Annular ring shank structural connector nails also available – call for details
316 Stainless Steel
Size
Length
Gauge
Shank
Diameter
Head
Diameter
Approx.
Count per lb.
25 lb.
Item No.
1 lb.
Item No.
8dx1 1⁄2
10dx1 1⁄2
8d
10d
16d
1 1⁄2"
1 1⁄2"
2 1⁄2"
3"
3 1⁄2"
10
9
10
9
8
.134"
.148"
.134"
.148"
.165"
⁄16 "
⁄16 "
9
⁄32"
5
⁄16 "
11
⁄32"
147
126
94
66
44
SSN8D25
SSN10D25
SS8D25
SS10D25
SS16D25
SSN8D
SSN10D
SS8DD
SS10DD
SS16DD
5
5
HAND-DRIVE NAILS | Un-Common™ Common Smooth Shank
• General-purpose nails with the heft to penetrate even the toughest seasoned timber
• Annular ring shank nails also available – see page 55.
304 Stainless Steel
Penny
Size
Length
Gauge
Shank
Diameter
Head
Diameter
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
4d
4d
8d
10d
16d
1 1⁄2"
1 1⁄2"
2 1⁄2"
3"
3 1⁄2"
10
9
10
9
8
.134"
.148"
.134"
.148"
.165"
⁄16 "
⁄16 "
9
⁄32"
5
⁄16 "
11
⁄32"
147
126
94
67
44
S4JHN25
S4HJHN25
S8JHN25
S10JHN25
S16JHN25
S4JHN5
S4HJHN5
S8JHN5
S10JHN5
S16JHN5
S4JHN1
S4HJHN1
S8JHN1
S10JHN1
S16JHN1
5
5
•
•
•
•
9
Length
Shank
Diameter
Box
Count
Item No.
2"
2"
2"
2"
2 1⁄4"
2 3⁄8"
2 3⁄8"
2 1⁄2"
2 1⁄2"
2 1⁄2"
3"
3"
3"
3"
3 1⁄4"
3 1⁄4"
3 1⁄4"
3 1⁄4"
3 1⁄2"
3 1⁄2"
.113"
.113"
.120"
.120"
.148"
.113"
.113"
.120"
.120"
.134"
.120"
.120"
.134"
.134"
.120"
.120"
.134"
.134"
.134"
.134"
5000
1000
5000
1000
1000
5000
1000
4000
1000
4000
4000
1000
4000
1000
4000
1000
4000
1000
4000
1000
S12A200CNB
S12A200CNJ
S11A200CNB
S11A200CNJ
S9A225CNJ
S12A237CNB
S12A237CNJ
S11A250CNB
S11A250CNJ
S10A250CNB
S11A300CNB
S11A300CNJ
S10A300CNB
S10A300CNJ
S11A325CNB
S11A325CNJ
S10A325CNB
S10A325CNJ
S10A350CNB
S10A350CNJ
Available
in 316*
—
—
These nails also available
in Silicon Bronze
Compatible Pneumatic Tools –
Collated 20–22° Plastic Strip
57
FRAMING
Collated Nails
• Silicon Bronze offers higher resistance to stress corrosion cracking in salt water
Silicon Bronze
Length
Shank
Diameter
Box
Count
Item No.
2 1⁄2"
.120"
4000
I11A250CNB
2 ⁄2"
.120"
1000
I11A250CNJ
1
3 ⁄4"
.120"
4000
I11A325CNB
3 1⁄4"
.120"
1000
I11A325CNJ
1
COLLATED NAILS | Plastic Strip 20–22°, Full Round Head, Screw Shank
•
•
•
•
9
Shank
Diameter
Box
Count
Item No.
2"
.113"
5000
S12S200CNB
2"
.113"
1000
S12S200CNJ
2 1⁄2"
.113"
4000
S12S250CNB
2 1⁄2"
.113"
1000
S12S250CNJ
3"
.120"
4000
S11S300CNB
3"
.120"
1000
S11S300CNJ
1
3 ⁄4"
.120"
4000
S11S325CNB
3 1⁄4"
.120"
1000
S11S325CNJ
1
3 ⁄2"
.134"
4000
S10S350CNB
3 1⁄2"
.134"
1000
S10S350CNJ
Available
in 316*
Length
Bostitch ®
Dewalt ®
Duo-Fast ®
Fasco ®
Hitachi ®
Makita ®
MAX ®
Paslode ®
Porter Cable ®
Senco ®
Stan-Tech ®
58
RN90, RN95HN (up to .162"), N88RH (up to .162"), N88HR-2MCN, F21PL
D51845, D51844
CN350, SNP-83, NSP-350F
R5C-RHN20-90SS
NR83A (up to 3 1⁄4"), NR90AC2 (up to .162"), NR90AC, NR90AA2, NR83AG, NR90SSC
AN8300, AN922
SN890RH, SN90, GS683
5350/SRH20
FR350, FR350A, FR350MAG
FramePro 600FRH & FramePro 602 (up to 3 1⁄2"), FramePro 650FRH (2 1⁄4" to 3 1⁄2"),
FramePro 652 (up to 3 1⁄2"), FramePro 700XL FRH, FramePro 702XP (upto 3 1⁄2") &
FramePro 752XP (up to 3 1⁄2"), SN60, SN65C (up to .162")
SDN11, SDN11B-1
!
Your Nail Gun, Our Fasteners
Tool manufacturers are constantly
introducing new tools to the market.
If you don’t see your particular
model in our tool compatibility
listings, visit www.strongtie.com
or call any of our locations and a
sales professional will assist you
in your fastener selection.
FRAMING
Collated Nails
COLLATED NAILS | Plastic Strip 20–22°, Full Round Head, Smooth Shank
• 9⁄32" diameter smooth, full round head
Length
Shank
Diameter
Box
Count
Available
in 316
1 1⁄2"
.148"
1000
T9N150JNJ
**
2 3⁄8"
.113"
5000
S12N237CNB
—
Item No.
2 3⁄8"
.113"
1000
S12N237CNJ
—
2 3⁄8"
.148"
1000
S9N237CNJ
—
3"
.148"
1000
S9N300CNJ
—
3 ⁄2"
.162"
1000
S8N350CNJ
—
1
COLLATED NAILS | Plastic Strip 20–22°, Casing Head, Ring Shank
• 1⁄4" diameter checker-patterned, countersunk casing head
• Orange or clear glue on nails to
enhance pull-out resistance
• Available with painted heads –
see below
Brown
304 Stainless Steel
Gray
Redwood Sienna
Length
Shank
Diameter
Box
Count
2 3⁄8"
.120"
1000
S11A237KDJ
3 1⁄4 "
.134"
1000
S10A325KDJ
Tan
Item No.
1. When ordering in colors, substitute the last three letters in the model number: KJB = Brown,
KJG = Gray, KJR = Redwood, KJS = Sienna; KJT = Tan. So a 2 3⁄8 " nail in Brown is model S11A237KJB.
COLLATED NAILS | Wire Weld 28°, Clipped Head, Ring Shank
• Side-by-side wire weld collation
304 Stainless Steel
Length
Shank
Diameter
Box
Count
Item No.
2 3⁄8"
.113"
1000
S12A237W28
3"
.120"
1000
S11A300W28
3 1⁄4"
.131"
1000
S10A325W28
Bostitch ®
Craftsman ®
Max®
Porter Cable ®
N16, N80SB and N86S (2" to 3 1⁄2"), N88WW, N100S,
N70S and N70SB (2" to 3"), N100S (2" to 4")
18430
SN890CH/28
FM350A
59
FRAMING
Collated Nails
Penny
Size
Length
Shank
Diameter
4d
1 1⁄2"
.099"
1
5d
1 3⁄4"
.099"
1
6d
2"
.099"
1
7d
2 1⁄4"
.099"
1
8d
2 1⁄2"
.099"
1
8d
2 3⁄8"
.113"
1
10d
3"
.120"
17
10d
3"
.131"
17
12d
3 1⁄4"
.120"
17
12d
1
3 ⁄4"
.131"
17
16d
3 ⁄2"
.131"
17
1
Head
Size
Box
Count
Item No.
Available
in 316*
⁄4"
3600
S12A150PNB
—
⁄4"
3600
S12A175PNB
—
⁄4"
3600
S12A200PNB
—
⁄4"
1800
T12A225PNJ
**
⁄4"
3600
S12A250PNB
⁄4"
3600
S12A237PNB
⁄64"
1800
S11A300PNJ
⁄64"
1800
S10A300PNJ
⁄64"
1800
S11A325PNJ
⁄64"
1800
S10A325PNJ
⁄64"
1800
T10A350PNJ
—
**
Bostitch ®
Fasco ®
Hitachi ®
Makita ®
MAX ®
Paslode ®
Porter Cable ®
Senco ®
Spotnails ®
Bostitch N80CB, N86C & N100C, N100CPP, N130C-2
F5C CN15W75 (up to 3") & CN15W90 (up to 3 1⁄4")
NV65AB & NV65AC (up to 2 1⁄2"), NV83A (up to 3 1⁄4"), NV75AG (.099" to .131", 1 3⁄4" to 3")
AN621(1 3⁄4" - 2 1⁄2"), AN901 (1 3⁄4" - 3 1⁄2")
CN80, CN70 (1 3⁄4" to 2 3⁄4"), HN75, HN90, 80F, CN100 (2 1⁄2" to 4"), CN565S (1 3⁄4" to 2 1⁄2"), CN890II,
CN565 (1 1⁄2" to 2 1⁄2"), CN890S, CN665 (1 1⁄2" to 2 1⁄2"), CN565D (1 3⁄4" to 2 1⁄2"), CN565S (1 3⁄4" to 2 1⁄2")
F325C, P350C (1 1⁄2" to 3 1⁄4"), F275C, P275C (1 1⁄2" to 2 3⁄4"), 4275/CN70 (2" to 2 1⁄2"), 5325/CN80 & 5350C, 5300C (up to 3")
Coil 350 (up to 3 1⁄2") , Coil 250 (up to 2 1⁄2")
SCN56 (up to 2 1⁄2") SCN60 (2" to 2 1⁄2") SCN65 (2" to 3 1⁄2") & SCN300 (1 3⁄4" to 3")
MCW64 (up to 2 1⁄2"), YCN83 (up to 3 1⁄4")
COLLATED NAILS | Paper Tape 31°, Structural Connector, Ring Shank
• Side-by-side paper tape collation
• 316 stainless steel for superior corrosion resistance
316 Stainless Steel
Penny
Size
Length
Shank
Diameter
4d Heavy
1 1⁄2"
.148"
9
8d Heavy
2 ⁄2"
.148"
9
1
Head
Size
Box
Count
Item No.
⁄32"
1500
T9A150MCN
⁄32"
1000
T9A250MCN
Compatible Pneumatic Tools – Collated 31° Paper Tape
Bostitch ®
Hitachi ®
Paslode ®
60
F33PT (1 1⁄2" - 2 1⁄2"), MCN150 (1 1⁄2"), MCN250 (2 1⁄2")
NR65AK
5250, F250S-PP
FRAMING
Collated Nails
Length
Shank
Diameter
Box
Count
Item No.
2 3⁄8"
.113"
4000
S12A237B31
3
2 ⁄8"
.113"
1000
S12A237P31
3"
.120"
4000
S11A300B31
3"
.120"
1000
S11A300P31
1
3 ⁄4"
.131"
4000
S10A325B31
3 1⁄4"
.131"
1000
S10A325P31
Available
in 316*
COLLATED NAILS | Paper Tape 31–34°, Clipped Head, Ring Shank
304 Stainless Steel
Length
Shank
Diameter
Box
Count
Item No.
2"
.113"
1000
S12A200T31
2 3⁄8"
.113"
1000
S12A237T31
3"
.120"
1000
S11A300T31
3 1⁄4"
.131"
1000
S10A325T31
3 1⁄2"
.131"
1000
S10A350T31
Available
in 316*
Compatible Pneumatic Tools – Collated 31–34° Paper Tape
Bostitch ®
DeWalt ®
Duofast ®
Hitachi ®
Makita ®
MAX ®
Paslode ®
Porter Cable ®
Senco ®
Spotnails ®
F33PT, N90PT (2" - 3 1⁄2")
D51823, D51822
NSPM-325F & CN-325B
NR83AA & NR83AA2, NR90AA
AN942
SN890CH/34, GS683CH
F350S Powermaster Plus, Impulse 325 & 350, 5325S, 5300 Plus & 5350S,
F250S-PP, IMCT (2" to 3 1⁄4")
FC350, FC350A
SN4, SN70, FramePro 600 & FramePro 650, SN325+, FramePro 601 (up to 3 1⁄2") &
FramePro 701XP (up to 3 1⁄2"), FramePro 651 (up to 3 1⁄2"), FramePro 750XL (up to 3 1⁄2")
& FramePro 751XP (up to 3 1⁄2")
YTD90
61
FRAMING
Hand-Drive Screws
HAND-DRIVE SCREWS | Timber Tamers ™, Hex Washer Head
• For superior corrosion resistance in a range of applications including timber framing,
pole barn construction, log homes, gutter installation and landscape timbers
• Available in screw sizes 1⁄4" and 3⁄8" and lengths from 3 to 12 inches
• 4-corner thread form significantly reduces driving torque
• Drive with standard 5⁄16" or 1⁄2" hex nut drivers
• Specify Timber Tamers™ for outdoor construction projects requiring longer length screws
Size
1
1
1
Carton
Count
Package
Count
Carton
Item No.
Package
Item No.
⁄16 "
1"
100
—
T14150TTB
—
⁄16 "
1 1⁄4"
100
—
T14200TTB
—
⁄16 "
1 1⁄2"
100
—
T14250TTB
—
⁄16 "
2 1⁄4"
100
20
T14300TTB
T14300TP
⁄16 "
2 1⁄4"
100
—
T14350TTB
—
⁄16 "
1
2 ⁄4"
100
20
T14400TTB
T14400TP
⁄16 "
1
2 ⁄4"
100
—
T14450TTB
—
⁄16 "
1
2 ⁄4"
100
10
T14500TTB
T14500TP
⁄16 "
1
2 ⁄4"
100
10
T14600TTB
T14600TP
1
5
1
⁄4" x 2"
5
⁄4" x 2 1⁄2"
5
1
⁄4" x 3"
5
⁄4" x 3 1⁄2"
5
⁄4" x 4"
5
⁄4" x 4 ⁄2"
5
⁄4" x 5"
5
⁄4" x 6"
5
⁄4" x 8"
5
1
1
1
⁄16 "
2 ⁄4"
50
10
T14800TTB
T14800TP
⁄8" x 3"
1
⁄2"
3"
100
10
T37300TTB
T37300TP
⁄8" x 4"
1
⁄2"
3"
100
10
T37400TTB
T37400TP
⁄8" x 5"
1
⁄2"
3"
50
10
T37500TTB
T37500TP
⁄8" x 6"
1
⁄2"
3"
50
10
T37600TTB
T37600TP
3
⁄8" x 8"
1
⁄2"
3"
25
10
T37800TTB
T37800TP
⁄8" x 10"
1
⁄2"
3"
25
10
T371000TTB
T371000TP
⁄8" x 12"
1
⁄2"
3"
25
—
T371200TTB
—
1
3
3
3
3
3
3
62
Thread
Length
⁄4" x 1 1⁄2"
1
1
Hex
Drive
316 Stainless Steel
FRAMING
Hand-Drive Screws
HAND-DRIVE SCREWS | Strong-Drive® Screw, Hex Washer Head
• Designed for installation in Simpson Strong-Tie ® structural connectors
as well as wood-to-wood applications
• Type-17 tip for fast starts, no predrilling required in most applications
• Patented 4CUT™ 4-corner thread form greatly reduces driving torque
• Double-barrier coating provides corrosion resistance equivalent to hot-dip galvanization
• Head is stamped with the Simpson Strong-Tie “No Equal” sign and fastener length
for easy identification after installation
• A low-speed 1⁄2" drill with a 3⁄8" hex driver is the recommended tool for installation
• Code listed under ICC-ES ESR-2236
Heat-Treated Carbon Steel
Size
Hex
Drive
Thread
Length
Retail Pack
Count
Retail Pack
Item No.
Mini Bulk
Count
⁄8"
1"
⁄8"
1 1⁄4"
25
SDS25112-R25
25
SDS25200-R25
⁄8"
1 1⁄2"
25
⁄8"
2"
⁄8"
2 1⁄4"
⁄4" x 1 1⁄4"
3
1
⁄4" x 2"
3
⁄4" x 2 1⁄2"
3
1
⁄4" x 3"
3
⁄4" x 31⁄2"
3
⁄4" x 4 ⁄2"
3
⁄4" x 6"
3
⁄4" x 8"
3
1
1
1
1
1
1
1
Mini Bulk
Item No.
Bulk Pack
Count
Bulk Pack
Item No.
300
SDS25112MB
1500
SDS25112
250
SDS25200MB
1300
SDS25200
SDS25212-R25
200
SDS25212MB
1100
SDS25212
25
SDS25300-R25
150
SDS25300MB
950
SDS25300
10
SDS25312-R10
125
SDS25312MB
900
SDS25312
⁄8"
3
2 ⁄4"
10
SDS25412-R10
100
SDS25412MB
800
SDS25412
⁄8"
3 1⁄4"
10
SDS25600-R10
100
SDS25600MB
600
SDS25600
⁄8"
3 1⁄4"
—
SDS25800-R10
—
SDS25800MB
400
SDS25800
SDS Screw Load Capacities
DF/SP Allowable Loads 3
Shear (100)
Size
(in.)
Wood Side Plate2
1
SPF/HF Allowable Loads 3
Steel Side Plate
Withdrawal4
(100)
Shear (100)
Wood Side Plate2
Steel Side Plate
Withdrawal4
(100)
1 1⁄2 "
1 3⁄4 "
SCL
16 ga
14 ga &
12 ga
10 ga or
Greater
Wood or Steel
Side Plate
1 1⁄2 "
1 3⁄4 "
SPF LVL
16 ga
14 ga &
12 ga
10 ga or
Greater
Wood or Steel
Side Plate
⁄32 x 1 1⁄4
—
—
50
50
50
—
—
—
45
45
45
—
1
⁄4 x 1 ⁄2
—
—
250
250
250
170
—
—
180
180
180
120
⁄4 x 2
—
—
—
290
290
215
—
—
—
210
210
150
⁄4 x 2 1⁄2
190
—
—
390
420
255
135
—
—
280
300
180
5
1
1
1
1
⁄4 x 3
280
—
—
420
420
345
200
—
—
300
300
240
1
⁄4 x 3 1⁄2
340
340
—
420
420
385
245
245
—
300
300
270
1
⁄4 x 4 1⁄2
350
340
—
420
420
475
250
245
—
300
300
330
⁄4 x 6
350
340
—
420
420
560
250
245
—
300
300
395
⁄4 x 8
350
340
—
420
420
560
250
245
—
300
300
395
1
1
1. Allowable loads for SDS screws are based on ICC-ES Code Report ESR-2236. Screws may be provided with the 4CUT™ or Type 17 tip.
2. Wood to wood applications are based on a wood thickness of 1 1⁄2 " side member. All applications are based on full penetration into the main member.
Refer to technical bulletin T-SDSCREWAPPS for allowable loads for other side member thicknesses.
3. Allowable loads are shown at the wood load duration factor of CD =1.00. Loads may be increased for load duration by the building code up to a CD =1.60.
4. Withdrawal loads shown are in pounds (lbs.) and are based on the entire threaded section installed into the main member.
If thread penetration into the main member is less than the Thread Length as shown in the table, reduce allowable load by 172 lbs. x inches of
thread not in main member. Use 121 lbs./inch for SPF.
5. LSL wood-to-wood applications that require 4 1⁄2 " and 6" SDS screws are limited to interior-dry use only.
6. See www.strongtie.com for important information and general notes for load-rated fasteners.
63
FINISHING, MILLWORK & TRIM
Fine Woodworking
When working with elaborate wood millings, trust Simpson Strong-Tie to match the quality
of your materials with fasteners of equal distinction. In addition to hand-driven finishing
nails, brads and escutcheon pins, we carry a large selection of stainless-steel collated
finishing nails, brads and staples engineered for today’s most popular pneumatic tools.
PVC Trim
Cellular PVC trim is a great alternative for traditional wood millwork – it won’t warp, cup,
or rot, and it’s generally warranted for 10 years or more. Simpson Strong-Tie offers
a variety of corrosion-resistant Swan Secure fasteners designed to last the life of the
warranty and beyond. Our Swaneze ™ #7 x 2 1⁄4 white painted trim screw is one of our
most popular options, followed by our white painted coil siding nails.
Hand-Drive Nails
Finishing .....................................................................................65
Fine
Woodworking
Collated Nails
Bostitch® -Type Angle Collated Finishing ...................................66
Senco ® -Type Angle Collated Finishing ......................................66
Paslode ® -Type Angle Collated Finishing ...................................66
Paslode ® -Type Straight Collated Finishing................................ 67
Straight 18-Gauge Collated Brads ............................................. 67
Wire Coil, Painted Siding ...........................................................68
Hand-Drive Screws
Trim Head, Square Drive, Swaneze ™ ..........................................69
Trim Head, 6-Lobe, Woodpecker ™ ..............................................69
Hand-Drive Screws, Painted Heads
Trim Head, Square Drive, Swaneze ™ ..........................................70
PVC Trim
Collated Staples
Similar To:
Bostitch® “BCS” Series .............................................................. 71
Senco ® “L” Series....................................................................... 71
Paslode ® “GS” Series ................................................................. 71
Senco ® “N” Series......................................................................72
Senco ® “P” Series ......................................................................72
Senco ® “C” Series ......................................................................72
64
Beautiful millwork and trim
accentuate premium construction,
and Simpson Strong-Tie offers
a wide range of high-grade
stainless-steel Swan Secure
fasteners expressly designed
and engineered for these
demanding applications where
only the best materials and
workmanship will do.
Hand-Drive Nails
HAND-DRIVE NAILS | Finishing Nails
• Brad head, smooth shank, diamond point
• Choose type 316 for seaside applications and superior
corrosion resistance
Penny
Size
Length
Gauge
Shank
Diameter
Head
Diameter
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
Bucket
Item No.
2d
1"
15
.072"
.109"
863
S2FN25
S2FN5
S2FN1
S2FNB
3d
1 1⁄4"
15
.072"
.109"
649
S3FN25
S3FN5
S3FN1
S3FNB
4d
1 1⁄2"
14
.083"
.120"
434
S4FN25
S4FN5
S4FN1
S4FNB
5d
1 3⁄4"
14
.083"
.120"
375
S5FN25
S5FN5
S5FN1
S5FNB
6d
2"
13
.095"
.135"
247
S6FN25
S6FN5
S6FN1
S6FNB
8d
1
2 ⁄2"
12
.109"
.148"
146
S8FN25
S8FN5
S8FN1
S8FNB
10d
3"
11
.120"
.165"
102
S10FN25
S10FN5
S10FN1
S10FNB
12d
3 1⁄4"
11
.120"
.165"
97
S12FN25
S12FN5
S12FN1
S12FNB
16d
3 1⁄2"
11
.120"
.165"
86
S16FN25
S16FN5
S16FN1
S16FNB
20d
4"
11
.120"
.201"
85
S20FN25
S20FN5
S20FN1
S20FNB
Available
in 316*
65
Collated Nails
COLLATED NAILS | Bostitch® -Type Angle Finishing
304 and 316 Stainless Steel – 15 Gauge
Length
Box Count
Item No.
1 1⁄2"
3500
S15N150FNJ
2"
3500
S15N200FNJ
2 1⁄2"
3500
S15N250FNJ
Available
in 316*
Bostitch ®
Makita ®
Stan-Tech ®
N60FN, N62FN
AF632
SDN15BR
COLLATED NAILS | Senco® -Type Angle Finishing
Item No.
Available
in 316*
4000
T15N125SFN
**
4000
S15N150SFN
2"
4000
S15N200SFN
2 1⁄2"
4000
S15N250SFN
Box Count
1 1⁄4"
1 1⁄2"
!
Accuset ®
Craftsman ®
DeWalt ®
Duofast ®
Hitachi ®
MAX ®
Porter Cable ®
Senco ®
A250FN
18442
D51275K
DAFN-6480
NT65AA & NT65MA &NT65MA2
NF550/15-65
DA250A & CDA250
AirFree 41, FinishPro 35, FinishPro 41XP, SFN40 & SFN1+ (up to 2"), SFN30 (11⁄4" to 2")
COLLATED NAILS | Paslode® -Type Angle Finishing
Length
Box Count
Item No.
1 1⁄4"
2000
S16N125PFN
1
1 ⁄2"
2000
S16N150PFN
2"
2000
S16N200PFN
2 1⁄2"
2000
S16N250PFN
DeWalt ®
Paslode ®
66
DC614KA, DC618KA
IM250A
Available
in 316*
CAUTION!
All of our collated finishing nails
and brads are held together with
a Mylar tape collation medium.
Although Mylar tape is flexible
and durable, care should be taken
when storing these products
between jobs. High heat, humidity,
and moisture can contribute to
the premature degradation of the
tape’s adherence which will cause
the fastener strips to fall free from
the collation which is not covered
by any warranty. Please remember
to keep collated fasteners of this
variety away from adverse
conditions.
Length
Collated Nails
COLLATED NAILS | Paslode® -Type 16 Gauge Straight Finishing
Length
Box Count
Item No.
Available
in 316*
1 1⁄4"
2500
T16N125FNJ
**
1
1 ⁄2"
2500
S16N150FNJ
2"
2500
S16N200FNJ
2 ⁄2"
2500
S16N250FNJ
1
Accuset ®
Bostitch ®
DeWalt ®
Duofast ®
Hitachi ®
Max®
Paslode ®
Porter Cable ®
Senco ®
A250SM
SB-1664FN, FN16250
D51256K
LFN-764A
NT65A, NT65A2
NF352-ST/16-50 (1" to 2")
IM250F, IM250II, MU-112B & MU-212-F, 3250-F16 & 3200-F16 (up to 2"),
T250-F16, 3250-F14 ( 3⁄4" to 2 1⁄2")
CFN250, FN250, FN250A & FN200 (up to 2")
FinishPro 32
COLLATED NAILS | Straight Brads
Length
Box Count
Item No.
Available
in 316*
⁄2"
5000
T18N050FNJ
**
⁄8"
5000
T18N062FNJ
**
⁄4"
5000
S18N075FNJ
1"
5000
T18N100FNJ
1
1 ⁄4"
5000
S18N125FNJ
1 1⁄2"
5000
S18N150FNJ
1
5
3
3
1 ⁄4"
5000
S18N175FNJ
2"
5000
S18N200FNJ
**
Bostitch ®
DeWalt ®
Hitachi ®
Max®
Paslode ®
Porter Cable ®
Senco ®
BT50B (1 3⁄16 " to 2"), T31-1B ( 5⁄8" to 1") & T29-30 ( 5⁄8" to 1 3⁄16 "), SB-1842BN &
2IN1 ( 5⁄8" -1 5⁄8"), SB-1850BN & BT200 ( 5⁄8" -2"), BT125 ( 5⁄8" -1 1⁄4")
D51238K ( 5⁄8" -2")
NT45A (1" to 1 3⁄4"), NT50AD (1" to 2"), NT32AE ( 5⁄8" to 1 1⁄4"), NT50AE ( 3⁄4" to 2"),
Bostitch BT35B ( 5⁄8" to 1 3⁄8")
NF201/18-35 ( 3⁄8" to 1 1⁄4"), NF221/18-55 ( 5⁄8" to 2")
2138-F18II & IM200-F18, T200-F18 ( 5⁄8" to 2"), T125-F18 ( 5⁄8" to 1 1⁄4")
BN125 ( 5⁄8" to 1 1⁄4") & BN200 ( 3⁄4" to 2")
FinishPro 15 ( 5⁄8" to 1 1⁄4"), FinishPro 18 ( 5⁄8" to 2"), FinishPro 25,
FinishPro 25XP ( 5⁄8" to 2"), FinishPro 2N1 ( 5⁄8" to 1 1⁄4"), AirFree 25 ( 5⁄8"-2 1⁄8"),
SLP20 (up to 1 1⁄2"), LS4 & LS5 (up to 1 5⁄8")
67
Collated Nails
COLLATED NAILS | Wire Coil, Painted Siding
•
•
•
•
•
Absolutely the highest quality nails for cedar, redwood and cypress siding materials
Stainless steel will last the life of wood siding without degrading in most environments
Generous under-head fillet allows nails to be driven flush, or countersunk, without
• Annular ring threads reduce cupping of siding boards and nail-head popping
304 Stainless Steel
Shank
Diameter
Head
Diameter
Color
Box
Count
Item No.
2"
.090"
13
2"
.090"
13
Dark Brown
3600
S13A200CCB
2"
.090"
13
⁄64"
Gray
3600
S13A200CCG
⁄64"
Redwood
3600
2"
.090"
13
S13A200CCR
⁄64"
Cedar
3600
S13A200CCT
⁄64"
White
3600
S13A200CWH
⁄64"
Dark Brown
3600
S13A219SNB
⁄64"
White
3600
S13A219SNC
⁄64"
Gray
3600
S13A219SNG
⁄64"
Redwood
3600
S13A219SNR
⁄64"
Cedar
3600
S13A219SNT
⁄64"
Dark Brown
3600
S13A250CCB
⁄64"
Gray
3600
S13A250CCG
⁄64"
Redwood
3600
S13A250CCR
⁄64"
Cedar
3600
S13A250CCT
⁄64"
White
3600
S13A250CWH
⁄64"
2"
.090"
13
2 3⁄16 "
.090"
13
2 ⁄16 "
.090"
13
2 3⁄16 "
.090"
13
2 3⁄16 "
.090"
13
2 ⁄16 "
.090"
13
2 1⁄2"
.090"
13
1
2 ⁄2"
.090"
13
2 1⁄2"
.090"
13
1
2 ⁄2"
.090"
13
2 ⁄2"
.090"
13
3
3
1
Bostitch ®
Hitachi ®
MAX ®
Paslode ®
Senco ®
NV65AH, NV65AC
CN565, CN565S, CN70 (1 3⁄4" to 2 3⁄4"), CN55 (1" to 2 1⁄4")
3225/CN55
SCN55S
Dark Brown Gray
Redwood
Cedar
!
Our collated painted siding nails
incorporate a slender shank
and a small head making them
perfect for many finishing and
millwork projects.
Both 1 1⁄2" and 1 3⁄4" lengths are
also available painted should
the requirement arise. Just call
any of our sales professionals
for pricing and lead time.
Custom colors are available
on any of our painted siding
nails provided that we have a
color swatch with which we
can match your color – please
call for details.
68
White
Length
Hand-Drive Screws
• Coarse threads approximately 2⁄3 up the shank draw the workpiece
• Pre-drilling always recommended, and a must near board ends to prevent splitting
• Use with stable woods and wood substitutes when screw heads need to be hidden
• Deck Packs contain 350 screws, enough to fasten 100 sq. ft.
• #7 screw has 0.230" head diameter and #1 square drive recess
• #9 x 3½" screw has 0.250" head diameter and #1 square drive recess
• #9 x 4" screw has 0.250" head diameter and #2 square drive recess
Size
Length
Approx.
Carton/Bucket
Count per lb.
Count
1 lb.
Item No.
Bulk Carton
Item No.
Bucket
Item No.
Deck Pack
Item No.
Available
in 316*
#7
1"
316
5000
S07100FB5
S07100FB1
S07100FBC
S07100FBB
S07C100PAK
—
#7
1 1⁄4"
256
5000
S07125FB5
S07125FB1
S07125FBC
S07125FBB
S07C125PAK
—
#7
5
1 ⁄8"
195
4000
S07162FB5
S07162FB1
S07162FBC
S07162FBB
S07C162PAK
#7
2"
154
4000
S07200FB5
S07200FB1
S07200FBC
S07200FBB
S07C200PAK
#7
1
2 ⁄4"
138
3000
S07225FB5
S07225FB1
S07225FBC
S07225FBB
S07C225PAK
#7
1
2 ⁄2"
126
2500
S07250FB5
S07250FB1
S07250FBC
S07250FBB
S07C250PAK
#7
3"
98
2000
S07300FB5
S07300FB1
S07300FBC
S07300FBB
S07C300PAK
#9
3 1⁄2"
62
1500
S09350FB5
S09350FB1
S09350FBC
S09350FBB
S09C350PAK
—
#9
4"
61
1000
S09400FB5
S09400FB1
S09400FBC
S09400FBB
—
—
5 lb.
Item No.
—
—
HAND-DRIVE SCREWS | Woodpeckers ™ Trim Head, 6-Lobe Drive
• Proprietary thread form greatly reduces torque and allows these screws
to drive into tropical hardwoods, often without pre-drilling
• 0.230" casing-style head and slender #7 diameter for finish work and trim
• Made of solid 316 stainless steel for superior corrosion resistance
• Threaded approximately 2⁄3 up the shank to tightly draw the workpiece to the substrate
• Pre-drilling not always necessary, except near board ends to prevent splitting
• 6-lobe driver bit included in both Bulk Cartons and Deck Packs
316 Stainless Steel
!
Size
Length
Head
Diameter
6-Lobe
Drive
Carton
Count
Bulk Carton
Item No.
Deck Pack
Count
Deck Pack
Item No.
#7
1 5⁄8"
0.230"
T-15
4000
T07162WPB
350
T07162WPP
#7
1
2 ⁄4"
0.230"
T-15
1750
T07225WPB
350
T07225WPP
#7
3"
0.230"
T-15
1750
T07300WPB
350
T07300WPP
Deck Packs contain enough screws to fasten up to 100 sq. ft. (6" nominal boards on 16" centers).
Bulk Cartons contain enough screws to fasten up to 500 sq. ft. (6" nominal boards on 16" centers).
69
Hand-Drive Screws – Painted Head
HAND-DRIVE SCREWS | Swaneze™ Painted Trim Head, Square Drive
Durable, powder-coated finish – painted heads blend with finish work
0.230" diameter #1 square drive, trim head
Coarse threads approximately 2⁄3 up the shank draw the workpiece tightly to the substrate
Choose type 316 for seaside applications
Mocha Azek
Gray
Gray Almond Ipê
Black White Khaki
Size
Length
Head Color
Contractor Pack
Count
Contractor Pack
Item No.
#7
1 5⁄8"
Gray
1750
#7
1 5⁄8"
Ipê
1750
#7
1 5⁄8"
Tan
#7
1 5⁄8"
White
#7
2 1⁄4"
Almond
#7
1
2 ⁄4 "
#7
2 1⁄4"
#7
2 1⁄4"
Ipê
1750
S07225FCI
350
S07225FJI
#7
2 1⁄4"
Khaki
1750
S07225FBK
350
S07225FJK
#7
2 ⁄4 "
Tan
1750
S07225FCT
350
S07225FJT
1
Deck Pack
Count
Deck Pack
Item No.
Available
in 316*
T07162FCG
350
T07162FJG
**
S07162FCI
350
S07162FJI
1750
T07162FCT
350
T07162FJT
1750
T07162FCW
350
S07162FJW
1750
S07225FCA
350
S07225FJA
—
Black
1750
S07225FCBB
350
S07225FJB
—
Gray
1750
S07225FCG
350
S07225FJG
**
—
#7
1
2 ⁄4 "
White
1750
S07225FCW
350
S07225FJW
#7
2 1⁄4"
Azek Gray
1750
S07225FCZ
350
S07225FZJ
#7
1
2 ⁄4 "
Mocha
1750
S07225FJM
350
S07225FCM
—
#7
3"
Gray
1750
S07300FCG
350
S07300FJG
—
#7
3"
Ipê
1750
S07300FCI
350
S07300FJI
—
#7
3"
Tan
1750
S07300FCT
350
S07300FJT
—
70
Tan
—
•
•
•
•
•
•
•
•
Collated Staples
Carton
Count
Gauge
Length
Item No.
16
1 1⁄4"
10,000
T16N125B07
16
1 1⁄2"
10,000
T16N150B09
16
1 3⁄4"
10,000
T16N175B11
16
2"
10,000
T16N200B13
Bostitch ®
Fasco ®
T36-1, T36-50, T50S4-1 & T55S4-1 ( 3⁄4" to 1 3⁄4") 438S2R (1⁄2" -1 1⁄2"),
T40S4-CT ( 3⁄4" to 1 1⁄2") , 438S4, 650S4
HD
COLLATED STAPLES | Similar to Senco® “L” Series
Carton
Count
Item No.
⁄8"
5000
S18N062L10
⁄4"
5000
T18N075L11
18
1"
5000
S18N100L13
18
1 1⁄8"
5000
S18N112L14
18
1
1 ⁄4"
5000
S18N125L15
18
1 ⁄2"
5000
S18N150L17
Gauge
Length
18
5
18
3
1
Available
in 316*
**
Duo-Fast ®
Grizzly®
Haubold ®
Hilti ®
Hitachi ®
Porter Cable ®
Senco ®
KN-1848A
G6043
PN6040H
SN-114B, SN-118
N3804A, N3804AA & N3804AB
NS100 (1⁄2" to 1") NS150 (1⁄2" -1 1⁄2")
FinishPro 2N1 (1⁄4" -1"), SLS15 ( 5⁄8" to 1"), SLS18 (1⁄2" -1 1⁄2"), SLS20,
SLS25XP ( 3⁄8" to 1 1⁄2"), SKSL12-17 (7⁄8" to 1 1⁄2"), SKSL11-15 ( 3⁄4" to 1 1⁄4")
Carton
Count
Gauge
Length
16
1 1⁄4"
10,000
S16N125GS
16
1 1⁄2"
10,000
S16N150GS
16
1 3⁄4"
10,000
S16N175GS
16
2"
10,000
S16N200GS
Item No.
Available
in 316*
—
Fasco ®
Paslode ®
GS
IM200-S16, 4200-S16 & 3200-S16P, 3150-S16 ( 3⁄4" to 1 1⁄2")
71
Collated Staples
Length
Carton
Count
Item No.
Available
in 316*
⁄4"
5000
T16N075N11
**
16
1"
5000
S16N100N13
16
1 1⁄4"
5000
S16N125N15
16
1
1 ⁄2"
5000
S16N150N17
16
1 3⁄4"
5000
S16N175N19
16
2"
5000
S16N200N21
Gauge
16
3
Bostitch ®
Hitachi ®
Fasco ®
Max®
Porter Cable ®
Senco ®
650S5
N5008AA & A1, N5008AB & N5008AC
G
TA551/16-11 (1" to 2")
CMS200 & MS200
M1 ( 3⁄4" -1 1⁄4"), SNS45 (1" -2"), SNS50 (1 1⁄4" -2"), SKS ( 3⁄4" to 1 1⁄2"), M2+ (1 1⁄4" to 2"), SNS45 (1" to 2")
COLLATED STAPLES | Similar to Senco “P” Series
304 and 316 Stainless Steel, 1" Crown
Length
Carton
Count
Available
in 316
Item No.
⁄4"
5000
S16N075P51
16
1"
5000
S16N100P53
16
1 1⁄4"
5000
S16N125P55
16
3
Hitachi ®
Senco ®
N3824A (1⁄2" -1 1⁄2") N5024A
PW ( 3⁄4" to 1 1⁄4") & MW ( 3⁄4" to 1 1⁄2"), SPS ( 3⁄4" to 1 1⁄2") & PW2 (1" to 2")
COLLATED STAPLES | Similar to Senco “C” Series
• Great for marine upholstery
Gauge
Length
Carton
Count
Item No.
⁄4"
10,000
S22N025C04
⁄8"
10,000
S22N037C06
⁄2"
10,000
S22N050C08
22
1
22
3
22
1
BeA ®
71/16-421
Porter Cable ® US58
Senco ®
SJ10 A/D, SFW10XP
72
Gauge
COMPOSITES & FIBERGLASS
Composite Lumber
Composite lumber is taking the nation by storm with the notion of a “maintenancefree deck.” Our premium, stainless-steel fasteners go a long way toward ensuring both
the structural integrity and corrosion-free appearance of decks built with composite
materials. One of our most recent product innovations, Dexxter ™ reduces bothersome
“mushrooming” thanks to a revolutionary thread design. What’s more, Dexxter requires
no pre-drilling and comes in a range of composite-matching head colors. Due to the
many composite types available it is difficult to predict final appearance, so always
test-drive fasteners to confirm acceptability.
Fiberglass
Whether you’re installing fiberglass panels or making repairs to a fiberglass boat, you’ll
appreciate our AISI type 316 stainless-steel Sharx ™ for their quick bite, extreme holding
power and exceptional corrosion resistance. Sharx are available with pan, flat or oval
heads – all with Phillips drive – and up to #14 screw diameter.
Hand-Drive Screws
With a growing trend toward “green”
building materials, composites and
fiberglass are becoming increasingly
popular as wood substitutes, primarily
because of their demonstrated
durability and reduced maintenance
requirements. Our equally durable,
corrosion-resistant fasteners will
virtually eliminate the likelihood of
unsightly staining of your building
project for years to come. Insist on
proven Simpson Strong-Tie ® Swan
Secure AISI-graded stainless-steel
fasteners in all of your wood-substitute
applications.
Composite Decking, 6-Lobe Drive, Dexxter ™ ....................................74
Marine, Flat Head, Sharx ™ ..................................................................74
Marine, Pan Head, Sharx ™ ................................................................ 75
Marine, Oval Head, Sharx ™ ............................................................... 75
Truss Head, Coarse Thread, Square Drive ........................................ 76
Trim Head, Square Drive, Swaneze ™ ................................................. 76
Trim Head, Square Drive, Swaneze™ with Sealing Washers.................77
Hand-Drive Nails
Common Ring Shank, Un-Common ™.................................................77
Composite Decking
Fiberglass Panels
73
Hand-Drive Screws
HAND-DRIVE SCREWS | Dexxter ™, Composite Decking, 6-Lobe Drive
• Unique thread form removes exhaust while driving to reduce
“mushrooming” in composite decking
• Small head diameter is less visible
• Painted heads available
• Patent pending
• Six-lobe driver included in both Contractor Packs and Deck Packs
Head
Diameter
6-Lobe
Drive
Contractor Pack
Count
Contractor Pack
Item No.
Deck Pack
Count
Deck Pack
Item No.
Available in
316
350
S10150DXP
—
350
S10200DXP
—
Size
Length
#10
1 1⁄2"
0.265"
T-20
1750
S10150DXB
#10
2"
0.265"
T-20
1750
S10200DXB
#10
1
2 ⁄2"
0.265"
T-20
1750
S10250DXB
350
S10250DXP
#10
3"
0.265"
T-20
1750
S10300DXB
350
S10300DXP
—
•
•
•
•
•
•
•
•
•
Sharx ™ screws bite and hold fast in fiberglass, plywood and wood substitute materials
Use for projects exposed to harsh marine or many chemically caustic conditions
Ideal for applying trim, rub rail and molding to fiberglass boat hulls
Extra-sharp points speed screw starts during assembly
Specially engineered, high/low thread form incorporates indentations (“teeth”) that
cut easily and quickly through high-density materials
Back-out resistance: once driven home, Sharx are locked in place thanks to their “teeth”
(the thread indentations will resist back-out even after prolonged vibration)
Holding power: Pull-out values of Sharx screws exceed those of ordinary
tapping screws in fiberglass and wood
Screws up to 1" in length are fully threaded.
Screws more than 1" long are threaded 2⁄3 of the shank length
Phillips drive
316 Stainless Steel, Flat Head
Size
74
Length
#6
1
#6
3
#8
3
Head
Diameter
Nominal
Screw Diameter
100-Count
Item No.
1000-Count
Item No.
⁄2"
.244/.279
.138
T06J050FXC
T06J050FXM
⁄4"
.244/.279
.138
T06J075FXC
T06J075FXM
⁄4"
.292/.332
.164
T08J075FXC
T08J075FXM
#6
1"
.244/.279
.138
T06J100FXC
T06J100FXM
#8
1"
.292/.332
.164
T08J100FXC
T08J100FXM
#10
1"
.340/.385
.190
T10J100FXC
T10J100FXM
#8
1 1⁄4"
.292/.332
.164
T08J125FXC
T08J125FXM
#10
1 1⁄4"
.340/.385
.190
T10J125FXC
T10J125FXM
#8
1
1 ⁄2"
.292/.332
.164
T08J150FXC
T08J150FXM
#10
1 1⁄2"
.340/.385
.190
T10J150FXC
T10J150FXM
#10
2"
.340/.385
.190
T10J200FXC
T10J200FXM
continued on following page >
HAND-DRIVE SCREWS | Sharx™ Marine Screws
Hand-Drive Screws
HAND-DRIVE SCREWS | Sharx™ Marine Screws
316 Stainless Steel, Pan Head
Size
Length
Head
Diameter
Nominal
Screw Diameter
100-Count
Item No.
1000-Count
Item No.
⁄2"
.256/.270
.138
T06J050PXC
T06J050PXM
⁄2"
.306/.322
.164
T08J050PXC
T08J050PXM
⁄2"
.357/.373
.190
T10J050PXC
T10J050PXM
#6
1
#8
1
#10
1
#6
3
#8
3
#10
3
⁄4"
.256/.270
.138
T06J075PXC
T06J075PXM
⁄4"
.306/.322
.164
T08J075PXC
T08J075PXM
⁄4"
.357/.373
.190
T10J075PXC
T10J075PXM
#6
1"
.256/.270
.138
T06J100PXC
T06J100PXM
#8
1"
.306/.322
.164
T08J100PXC
T08J100PXM
#10
1"
.357/.373
.190
T10J100PXC
T10J100PXM
#12
1"
.407/.425
.216
T12J100PXC
T12J100PXM
#14
1"
.473/.492
.242
T14J100PXC
T14J100PXM
#8
1
1 ⁄4"
.306/.322
.164
T08J125PXC
T08J125PXM
#10
1 1⁄4"
.357/.373
.190
T10J125PXC
T10J125PXM
#12
1
1 ⁄2"
.407/.425
.216
T12J150PXC
T12J150PXM
#14
1 1⁄2"
.473/.492
.242
T14J150PXC
T14J150PXM
#12
2"
.407/.425
.216
T12J200PXC
T12J200PXM
#14
2"
.473/.492
.242
T14J200PXC
T14J200PXM
Length
Head
Diameter
Nominal
Screw Diameter
100-Count
Item No.
1000-Count
Item No.
⁄4"
.244/.279
.138
T06J075OXC
T06J075OXM
⁄4"
.292/.332
.164
T08J075OXC
T08J075OXM
⁄4"
.340/.385
.190
T10J075OXC
T10J075OXM
316 Stainless Steel, Oval Head
Size
#6
3
#8
3
#10
3
#6
1"
.244/.279
.138
T06J100OXC
T06J100OXM
#8
1"
.292/.332
.164
T08J100OXC
T08J100OXM
#10
1"
.340/.385
.190
T10J100OXC
T10J100OXM
#12
1"
.380/.412
.216
T12J100OXC
T12J100OXM
#14
1"
.427/.462
.242
T14J100OXC
T14J100OXM
#8
1 1⁄4"
.292/.332
.164
T08J125OXC
T08J125OXM
#10
1 1⁄4"
.340/.385
.190
T10J125OXC
T10J125OXM
#8
1
1 ⁄2"
.292/.332
.164
T08J150OXC
T08J150OXM
#10
1
1 ⁄2"
.340/.385
.190
T10J150OXC
T10J150OXM
#12
1 1⁄2"
.380/.412
.216
T12J150OXC
T12J150OXM
#14
1
1 ⁄2"
.427/.462
.242
T14J150OXC
T14J150OXM
#12
2"
.380/.412
.216
T12J200OXC
T12J200OXM
#14
2"
.427/.462
.242
T14J200OXC
T14J200OXM
75
Hand-Drive Screws
HAND-DRIVE SCREWS | Truss Head, Coarse Thread, Square Drive
• #2 square drive truss head, coarse thread similar to Swaneze™ screws
• Fasten all materials to wood or wood-substitute materials
• Pre-drilling recommended – dependent on substrate
305 Stainless Steel
Size
Length
Carton Count
Item No.
#8
1"
100
S08C100TSC
#8
1"
1000
S08C100TSM
#8
1"
2000
S08C100TSB
#8
1
1 ⁄4"
100
S08C125TSC
#8
1 1⁄4"
1000
S08C125TSM
#8
1 1⁄2"
100
S08C150TSC
#8
1
1 ⁄2"
1000
S08C150TSM
#8
2 1⁄2"
100
S08C250TSC
#8
2 ⁄2"
1000
S08C250TSM
1
•
•
•
•
•
•
•
•
•
Coarse threads approximately 2⁄3 up the shank draw board tightly to the substrate
#7 screw has 0.230" head diameter and #1 square drive recess
#9 x 31⁄2" screw has 0.250" head diameter and #1 square drive recess
#9 x 4" screw has 0.250" head diameter and #2 square drive recess
Bucket = 25 lbs.
Size
Length
Approx.
Count per lb.
Carton
Count
5 lb.
Item No.
1 lb.
Item No.
Bulk Carton
Item No.
Bucket
Item No.
Deck Pack
Item No.
Available
in 316*
#7
1"
316
5000
S07100FB5
S07100FB1
S07100FBC
S07100FBB
S07C100PAK
—
#7
1 1⁄4"
256
5000
S07125FB5
S07125FB1
S07125FBC
S07125FBB
S07C125PAK
—
#7
5
1 ⁄8"
195
4000
S07162FB5
S07162FB1
S07162FBC
S07162FBB
S07C162PAK
#7
2"
154
4000
S07200FB5
S07200FB1
S07200FBC
S07200FBB
S07C200PAK
#7
2 1⁄4"
138
3000
S07225FB5
S07225FB1
S07225FBC
S07225FBB
S07C225PAK
#7
2 1⁄2"
126
2500
S07250FB5
S07250FB1
S07250FBC
S07250FBB
S07C250PAK
#7
3"
98
2000
S07300FB5
S07300FB1
S07300FBC
S07300FBB
S07C300PAK
#9
3 1⁄2"
62
1500
S09350FB5
S09350FB1
S09350FBC
S09350FBB
S09C350PAK
—
#9
4"
61
1000
S09400FB5
S09400FB1
S09400FBC
S09400FBB
—
—
!
76
Bulk Cartons contain enough screws to fasten 500 sq. ft. (6" nominal boards on 16" centers).
—
—
Hand-Drive Screws / Hand-Drive Nails
HAND-DRIVE SCREWS | Swaneze™ Trim Head, with Sealing Washers
•
•
•
•
•
Assemblies provide weathertight seal for use in exterior sheathing and roofing applications
Washers are 302 stainless steel bonded to neoprene and 5⁄8" in diameter
Other sizes available – contact Simpson Strong-Tie for details
#1 square drive
305 Stainless Steel
Size
Length
Carton
Count
Item No.
#7
1 5⁄8"
100
S07C162X0C
#7
1 ⁄8"
1000
S07C162X0M
5
#7
1
2 ⁄4"
100
S07C225X0C
#7
2 1⁄4"
1000
S07C225X0M
#7
3"
100
S07C300X0C
#7
3"
1000
S07C300X0M
HAND-DRIVE NAILS | Un-Common™ Common Ring Shank
• All-around, general purpose structural nails with the heft to penetrate even the
toughest seasoned timber
• First choice for construction of permanent wood foundations by the
ANSI/AF&PA Permanent Wood Foundations Design Specifications
• Annular ring nails for greater pull-out resistance
• Also available in screw shank – call for details
Penny
Size
Length
Gauge
Shank
Diameter
Head
Diameter
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
Bucket
Item No.
2d
1"
15
.072"
3
3d
1
1 ⁄4"
14
.083"
7
4d
1
1 ⁄2"
12
.109"
1
5d
1 3⁄4"
12
.109"
1
6d
2"
11
.120"
17
7d
1
2 ⁄4"
11
.120"
17
8d
2 1⁄2"
10
.134"
9
10d
3"
9
.148"
5
12d
3 1⁄4"
9
.148"
5
16d
3 1⁄2"
8
.165"
11
⁄16 "
807
S2ACN25
S2ACN5
S2ACN1
S2ACNB
⁄32"
473
S3ACN25
S3ACN5
S3ACN1
S3ACNB
⁄4"
228
S4ACN25
S4ACN5
S4ACN1
S4ACNB
⁄4"
193
S5ACN25
S5ACN5
S5ACN1
S5ACNB
⁄64"
144
S6ACN25
S6ACN5
S6ACN1
S6ACNB
⁄64"
133
S7ACN25
S7ACN5
S7ACN1
S7ACNB
⁄32"
94
S8ACN25
S8ACN5
S8ACN1
S8ACNB
⁄16 "
67
S10ACN25
S10ACN5
S10ACN1
S10ACNB
⁄16 "
60
S12ACN25
S12ACN5
S12ACN1
S12ACNB
⁄32"
44
S16ACN25
S16ACN5
S16ACN1
S16ACNB
20d
4"
6
.203"
7
30d
4 1⁄2"
6
.203"
7
⁄16 "
25
S20ACN25
S20ACN5
S20ACN1
S20ACNB
⁄16 "
22
S30ACN25
S30ACN5
S30ACN1
—
⁄16 "
19
S40ACN25
S40ACN5
S40ACN1
S40ACNB
⁄32"
12
S60ACN25
S60ACN5
S60ACN1
—
⁄32"
10
S70ACN25
S07ACN5
S70ACN1
—
40d
5"
6
.203"
7
60d
6"
4
.238"
15
70d
7"
4
.238"
15
Available
in 316*
77
METAL FRAMING
METAL FRAMING
Metal Framing
Our innovative stainless-steel, self-drilling screws are fashioned from heat-treated
AISI type 410 alloy and coated to facilitate installation and add a secondary defense
against corrosion. Our Billy Goat ™ bugle head and trim-head screws are your best
option for attaching wood, plywood or fiber cement to steel studs. They’re available
in a variety of head, thread and drive configurations to match a variety of applications.
Metal Lath
Our self-drilling K-Lath screws feature a phillips-drive recess and a large modified
truss head. These screws combine a low-profile head with a large bearing surface to
make this fastener ideal for holding lath to metal stud, or attaching plywood to metal.
The shorter lengths are ideal for attaching one metal stud to another.
Hand-Drive Screws
Self-Drilling, Bugle Head, Billy Goats ™.................................................. 79
Self-Drilling, Trim Head, Billy Goats ™ ................................................... 79
Our self-drilling screws are designed and
engineered to secure a wide range of
materials including fiberglass, composites,
fiber cement, wood, metal and gypsum
board – to wood or metal studs. When it
comes to installations involving masonry,
you’ll find that Simpson Strong-Tie offers
the most diverse range of AISI type 410
stainless-steel screws on the market today.
Metal Lath
78
Self-Drilling, Wafer Head with Wings, Billy Goats ™ .............................. 80
Self-Drilling, Marutex, Hex Washer Head, Billy Goats ™ .........................81
Self Drilling, Fiber Cement, Metal Stud, Billy Goats ™ ........................... 82
Self-Drilling, K-Lath Modified Truss Head, Billy Goats ™......................... 82
Standard Drilling Capacities and Drill Speed Recommendations for
410 Stainless-Steel Self-Drilling Screws
Nominal
Screw Size
Point Style
Recommended
Steel Thickness
Recommended
Drill Speed (R.P.M.)
#6
No. 2
0.059 – 0.083"
2500 Max.
#8
No. 2
0.059 – 0.110"
2500 Max.
#8
No. 3
0.098 – 0.142"
2500 Max.
#10
No. 2
0.059 – 0.142"
2500 Max.
#10
No. 3
0.110 – 0.177"
2500 Max.
#12
No. 3
0.110 – 0.209"
1800 Max.
#12
No. 4
0.177 – 0.354"
1800 Max.
#12
No. 5
0.250 – 0.500"
1800 Max.
#14
No. 3
0.110 – 0.248"
1800 Max.
#14
No. 4
0.250 – 0.375"
1800 Max.
#14
No. 5
0.250 – 0.500"
1800 Max.
Metal Framing
Self-Drilling, Flat Head with Wings, Billy Goats ™ .................................. 80
METAL FRAMING
HAND-DRIVE SCREWS | Billy Goats™, Self-Drilling, Bugle Head
•
•
•
•
Fasten wood, plywood and OSB panels to steel studs
#2 square-drive bugle heads drive flush with work surface
Tapping screw threads, #3 drill points
Drilling thickness capacities: up to .083" (68 mils, 14 ga.) for #6,
up to .142" (118 mils, 10 ga) for #8 and up to .177" for #10
410 Stainless Steel
Size
Length
#6
1 1⁄4"
100
F06T125BDC
#6
1 1⁄4"
1000
F06T125BDM
#6
1 1⁄4"
5000
F06T125BDB
#8
1 5⁄8"
100
F08T162BDC
#8
1 5⁄8"
1000
F08T162BDM
#8
1 5⁄8"
3000
F08T162BDB
#8
2"
100
F08T200BDC
#8
2"
1000
F08T200BDM
#8
2"
2500
F08T200BDB
#10
2 1⁄2"
100
F10T250BDC
#10
2 1⁄2"
1000
F10T250BDM
#10
2 1⁄2"
2000
F10T250BDB
#10
3"
100
F10T300BDC
#10
3"
1500
F10T300BDB
#10
3 1⁄2"
100
F10T350BDC
#10
3 ⁄2"
1000
F10T350BDB
1
Carton Count
Item No.
HAND-DRIVE SCREWS | Billy Goats™, Self-Drilling, Trim Head
•
•
•
•
Attach wood siding, wood panels and metal trim to steel studs
#1 square drive, .230" head diameter, #3 drill point
Threaded 2⁄3 of overall length
Drilling thickness capacity: up to .125" (111 mils, 11 ga)
410 Stainless Steel
Size
Length
Carton Count
Item No.
#7
1 5⁄8"
100
F07T162TDC
#7
1 5⁄8"
1000
F07T162TDM
#7
1 5⁄8"
5000
F07T162TDB
#7
2 1⁄4"
100
F07T225TDC
#7
2 1⁄4"
1000
F07T225TDM
#7
2 1⁄4"
4000
F07T225TDB
#7
3"
100
F07T300TDC
#7
3"
1000
F07T300TDM
#7
3"
2000
F07T300TDB
For more information on drilling thickness capacities and drill speed recommendations see page 78.
79
METAL FRAMING
Hand-Drive Screws
HAND-DRIVE SCREWS | Billy Goats™, Self-Drilling, Flat Head with Wings
•
•
•
•
•
•
•
Fasten wood, plywood and fiber cement to heavier steel – up to .209" thick
#3 square drive
Machine screw thread, threaded full length
2 1⁄2" length for 2x4 wood header; 2" length for 1" and 5⁄4" boards
Flat countersunk head with self-countersinking nibs
Shank slot enhances thread formation in steel and removes exhaust
Wings above drill point provide clearance hole in work piece so it won’t climb up
the shank, then break off as point engages the steel substrate
• Drilling thickness capacities: up to .209" (171 mils, 7 ga) for #12,
up to .250" (229 mils, 3 ga) for #14
410 Stainless Steel
Head
Diameter
Drill
Point Size
⁄8"
#3
100
F12C200FDC
⁄8"
#3
1000
F12C200FDM
⁄8"
#3
2500
F12C200FDB
⁄8"
#3
100
F12C250FDC
⁄8"
#3
1000
F12C250FDM
Size
Length
#12
2"
3
#12
2"
3
#12
2"
3
#12
1
2 ⁄2"
3
#12
2 1⁄2"
3
#12
2 1⁄2"
3
#14
3 1⁄4"
15
#14
3 1⁄4"
15
Carton Count
Item No.
⁄8"
#3
1800
F12C250FDB
⁄32"
#4
100
F14C325FDC
⁄32"
#4
1000
F14C325FDM
HAND-DRIVE SCREWS | Billy Goats™, Self-Drilling, Wafer Head with Wings
• Attach plywood and OSB panels to steel studs
• Machine-screw thread, threaded full length, #3 drill point
• Wings above drill point provide clearance hole in work piece so it won’t climb up
the shank and break off as point engages the steel substrate
• 0.450" diameter head
410 Stainless Steel
Size
Length
Carton Count
Item No.
#10
1 7⁄16 "
100
F10C144WDC
#10
1 ⁄16 "
1000
F10C144WDM
#10
1 ⁄16 "
4500
F10C144WDB
7
7
80
METAL FRAMING
Hand-Drive Screws
HAND-DRIVE SCREWS | Billy Goats™, Marutex, Self-Drilling, Hex Washer Head
• Stainless-steel self-drillers for the most demanding projects, features the
drilling capabilities of 410 stainless with increased corrosion resistance
• Will withstand over 300 hours salt spray with no oxidation
• Rockwell C-53 typical hardness
• Magnetic – heat-treated and passivated chrome/moly alloy
• Indented hex head, tapping screw thread, #3 drill point
• Screws are available with bonded sealing washers, please call for details
Marutex
Size
Length
Hex Head
Size
Carton Count
Item No.
⁄4"
100
X08050HDUC
⁄4"
1000
X08050HDUM
⁄4"
100
X08075HDUC
⁄4"
1000
X08075HDUM
⁄2"
1
⁄2"
1
⁄4"
1
⁄4"
1
#8
1"
1
#8
1"
1
#8
1
#8
1
#8
3
#8
3
#10
1
#10
1
#10
3
#10
3
⁄2"
5
⁄2"
5
⁄4"
5
⁄4"
5
#10
1"
5
#10
1"
5
#10
1 1⁄2"
5
#10
1 1⁄2"
5
#12
3
#12
3
100
X10050HDUC
X10050HDUM
⁄16 "
100
X10075HDUC
⁄16 "
1000
X10075HDUM
⁄16 "
100
X10100HDUC
⁄16 "
1000
X10100HDUM
⁄16 "
100
X10150HDUC
⁄16 "
1000
X10150HDUM
5
#12
1"
5
#12
1"
5
#12
1 1⁄2"
5
#12
1
1 ⁄2"
5
#12
2"
5
#12
2"
5
#12
2 1⁄2"
5
#12
1
2 ⁄2"
5
#12
3"
5
#12
3"
5
#14
X08100HDUM
1000
⁄4"
3
X08100HDUC
1000
⁄16 "
⁄4"
3
100
⁄4"
⁄16 "
5
#14
⁄4"
⁄16 "
100
X12075HDUC
⁄16 "
1000
X12075HDUM
⁄16 "
100
X12100HDUC
⁄16 "
1000
X12100HDUM
⁄16 "
100
X12150HDUC
⁄16 "
1000
X12150HDUM
⁄16 "
100
X12200HDUC
⁄16 "
1000
X12200HDUM
⁄16 "
100
X12250HDUC
⁄16 "
1000
X12250HDUM
⁄16 "
100
X12300HDUC
⁄16 "
1000
X12300HDUM
⁄4"
3
⁄4"
3
⁄8"
100
X14075HDUC
⁄8"
1000
X14075HDUM
#14
1"
3
#14
1"
3
#14
1-"
3
#14
1-"
3
#14
2"
3
#14
2"
3
#14
2 1⁄2"
3
#14
1
2 ⁄2"
3
#14
3"
3
#14
3"
3
⁄8"
100
X14100HDUC
⁄8"
1000
X14100HDUM
⁄8"
100
X14150HDUC
⁄8"
1000
X14150HDUM
⁄8"
100
X14200HDUC
⁄8"
1000
X14200HDUM
⁄8"
100
X14250HDUC
⁄8"
1000
X14250HDUM
⁄8"
100
X14300HDUC
⁄8"
1000
X14300HDUM
!
Many of our 410SS screws are
coated to insure better corrosion
resistance and ease of installation.
Grade 410 stainless steel can be
hardened through heat treatment
giving it the ability to drill through
metal. It does not offer the same
level of corrosion resistance of
either type 305 or 316 stainless
steel.
81
METAL FRAMING
Hand-Drive Screws
HAND-DRIVE SCREWS | FY-CEM Billy Goats™, Self-Drilling, Fiber-Cement Screws, Metal Stud
•
•
•
•
•
Fasten fiber cement through furring strips to steel studs
#2 square drive, #3 drill point
Wafer head
Threaded to within 5⁄16" of top of head
Self-countersinking nibs under head ensure seating of screw heads flush with work surface
410 Stainless Steel
Size
Length
Head Size
Carton Count
Item No.
#8
1 5⁄8"
.390"
100
F08T162WDC
#8
1 ⁄8 "
F08T162WDM
.390"
1000
#8
5
1 ⁄8 "
.390"
3000
F08T162WDB
#8
2 1⁄4"
.390"
100
F08T225WDC
#8
2 1⁄4"
.390"
1000
F08T225WDM
#8
2 1⁄4"
.390"
2500
F08T225WDB
5
HAND-DRIVE SCREWS | K-Lath Modified Truss Head, Self-Drilling
• For attaching metal lath to 14- to 20-gauge steel studs
• Tapping screw threads, #3 drill point
Size
Length
Carton Count
Item No.
⁄16 "
100
F08T056KDC
⁄16 "
1000
F08T056KDM
⁄16 "
8000
F08T056KDB
⁄4"
100
F08T075KDC
⁄4"
1000
F08T075KDM
⁄4"
6000
F08T075KDB
#8
9
#8
9
#8
9
#8
3
#8
3
#8
3
#8
1
1 ⁄4"
100
F08T125KDC
#8
1 1⁄4"
1000
F08T125KDM
#8
1 1⁄4"
4000
F08T125KDB
#8
5
1 ⁄8"
100
F08T162KDC
#8
1 5⁄8"
1000
F08T162KDM
#8
1 5⁄8"
3000
F08T162KDB
#8
2"
100
F08T200KDC
#8
2"
1000
F08T200KDM
#8
2"
2500
F08T200KDB
82
410 Stainless Steel
SPECIALTY ITEMS
SPECIALTY ITEMS
Specialty Nails
Simpson Strong-Tie is proud to be one of the last remaining manufacturers of
stainless-steel and copper alloy nails in the United States. We specialize in AISI grade
304 and 316 stainless steel, aluminum, brass, commercial bronze, copper, monel, and
silicon bronze.
Fence Staples and Hog Rings
Fence staples and hog rings have plenty of practical applications. Finding them in
stainless steel, however, is not so easy. While we stock both in AISI grade 304 stainless
steel, certain sizes are available in alternate alloys including AISI grade 316 and silicon
bronze – please call for current availability.
Specialty Tools
Swan Secure tools are offered to help our customers – from contractors to resourceful
home owners – make the best use of their time and skills. Our Drill N’ Drive™ pre-drills
and countersinks for #7 trim-head screws, an absolute must for anyone working with
tropical hardwoods such as Ipê. Our premium driver bits are US-made and custom fit
to ensure maximum reliability and bit life.
We listen carefully to the needs of our
customers and actively strive to provide
innovative, problem-solving products
in a timely and responsible manner.
Our manufacturing facility can produce
custom nails to unique specifications
and we stock the largest assortment
of top quality, corrosion resistant
stainless-steel fasteners available.
Specialty Hand-Drive Nails
Marine, Sea-Cure ™ ........................................................................... 84
Fencing ............................................................................................. 85
Custom-Order .................................................................................. 85
Traditional Fasteners
Fencing Staples ................................................................................ 85
Hog Rings......................................................................................... 85
Special Tools
Premium Driver Bits ......................................................................... 86
Drill N’ Drive ™ ................................................................................... 86
Special Applications
Ipê Wood Plugs .................................................................................87
Storm-Panel Screw ...........................................................................87
83
SPECIALTY ITEMS
SPECIALTY NAILS | Sea-Cure™ Marine
• Special selection of large-headed nails for wooden boat building and repair
• Large bearing surface under heads for new construction and re-nailing projects
• Silicon bronze offers resistance to stress corrosion cracking under nail heads
in salt water applications
• Monel® is a nickel/copper alloy formulated for optimum service life in salt-water applications.
It is required by the Coast Guard for refastening wooden boats in commercial service
Stainless Steel, Silicon Bronze, Commercial Bronze, Monel
Gauge
Shank
Diameter
⁄4"
15
.072"
3
⁄4"
14
.083"
7
⁄8"
14
.083”
7
1"
15
.072"
3
1"
14
.083"
7
3
3
7
Head
Diameter
Approx. Count
per lb. SS
Approx. Count
per lb. Cu Alloy
5 lb.
Item No.
1 lb.
Item No.
⁄16 "
1050
913
S15075SC25
S15075SC5
S15075SC1
⁄32"
757
664
S14075SC25
S14075SC5
S14075SC1
⁄32"
657
617
S14087SC25
S14087SC5
S14087SC1
⁄16 "
807
689
S15100SC25
S15100SC5
S15100SC1
⁄32"
622
536
S14100SC25
S14100SC5
S14100SC1
1"
12
.109"
17
1 1⁄4"
14
.083"
7
⁄64"
364
303
S12100SC25
S12100SC5
S12100SC1
⁄32"
473
424
S14125SC25
S14125SC5
1
1 ⁄4"
12
.109"
17
S14125SC1
1 1⁄2"
14
.083"
7
1
1 ⁄2"
12
.109"
17
1
1 ⁄2"
10
.134"
3
1 3⁄4"
12
.109"
17
3
1 ⁄4"
10
.134"
3
2"
12
.109"
17
2"
10
.134"
3
⁄64"
272
245
S12125SC25
S12125SC5
S12125SC1
⁄32"
413
374
S14150SC25
S14150SC5
S14150SC1
⁄64"
228
204
S12150SC25
S12150SC5
S12150SC1
⁄8"
147
132
S10150SC25
S10150SC5
S10150SC1
⁄64"
193
179
S12175SC25
S12175SC5
S12175SC1
⁄8"
130
118
S10175SC25
S10175SC5
S10175SC1
⁄64"
175
161
S12200SC25
S12200SC5
S12200SC1
⁄8"
114
104
S10200SC25
S10200SC5
S10200SC1
2"
8
.165"
2 1⁄2"
10
.134"
⁄16 "
75
65
S8200SC25
S8200SC5
S8200SC1
3
⁄8"
94
83
S10250SC25
S10250SC5
S10250SC1
2 1⁄2"
8
.165"
3"
10
.134"
3
⁄16 "
62
54
S8250SC25
S8250SC5
S8250SC1
⁄8"
79
71
S10300SC25
S10300SC5
S10300SC1
3"
9
.148"
3
⁄8"
67
58
S9300SC25
S9300SC5
S9300SC1
⁄16 "
51
45
S8300SC25
S8300SC5
S8300SC1
⁄2"
34
31
S6300SC25
S6300SC5
S6300SC1
7
7
3"
8
.165"
3"
6
.203"
1
3 1⁄4"
9
.148"
3
⁄8"
60
52
S9325SC25
S9325SC5
S9325SC1
3 1⁄4"
8
.165"
7
⁄16 "
48
43
S8325SC25
S8325SC5
S8325SC1
3 1⁄2"
8
.165"
7
⁄16 "
44
40
S8350SC25
S8350SC5
S8350SC1
1
3 ⁄2"
6
.203"
1
⁄2"
29
26
S6350SC25
S6350SC5
S6350SC1
4"
6
.203"
1
⁄2"
25
23
S6400SC25
S6400SC5
S6400SC1
4"
4
.238"
4 1⁄2"
6
.203"
1
4 ⁄2"
4
.238"
5"
6
.203"
5"
4
.238"
9
6"
4
.238"
9
7
⁄16 "
18
17
S4400SC25
S4400SC5
S4400SC1
⁄2"
22
20
S6450SC25
S6450SC5
S6450SC1
⁄16 "
16
15
S4450SC25
S4450SC5
S4450SC1
9
1
9
⁄2"
19
18
S6500SC25
S6500SC5
S6500SC1
⁄16 "
15
14
S4500SC25
S4500SC5
S4500SC1
⁄16 "
12
11
S4600SC25
S4600SC5
S4600SC1
1
* For items in 316 stainless steel, substitute the letter “T” as the first character of the item number;
for silicon bronze, the letter “I”; for commercial bronze, the letter “O”; for Monel, the letter “M”.
84
25 lb.
Item No.
Length
SPECIALTY ITEMS
SPECIALTY NAILS | Fencing
• Prevent unsightly streaks and stains on any wood or vinyl fence
• Checker-patterned head blends with wood texture, serves to diffract sunlight and
accepts surface finishes
• Annular ring threads reduce nail-head popping
Penny
Size
Length
Gauge
Shank
Diameter
5d
1 3⁄4"
12
.109"
15
6d
2"
12
.109"
15
Head
Diameter
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
⁄64"
193
S5FNX25
S5FNX5
S5FNX1
⁄64"
175
S6FNX25
S6FNX5
S6FNX1
Available
in 316*
TRADITIONAL FASTENERS | Fencing Staples
Gauge
Length
Approx.
Count per lb.
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
Available
in 316*
13
1"
291
S13100FS25
S13100FS5
S13100FS1
—
13
1
1 ⁄4"
202
S13125FS25
S13125FS5
S13125FS1
10
2"
66
S10200FS25
S10200FS5
S10200FS1
—
TRADITIONAL FASTENERS | Hog Rings
304 Stainless Steel, Blair Shaped
Gauge
Width
Open
Width
Across
Approx. Count
per lb.
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
12
.95"
1.82"
111
S12131HR25
S12131HR5
S12131HR1
304 Stainless Steel, #3 Pre-Bent, Hill Pattern (pictured)
Gauge
Width
Open
Width
Across
Approx. Count
per lb.
25 lb.
Item No.
5 lb.
Item No.
1 lb.
Item No.
13
.812"
1.57"
204
S13075HR25
S13075HR5
S13075HR1
SPECIALTY NAILS | Custom Order
Simpson Strong-Tie is proud to be one of the last remaining manufacturers of stainless-steel and
copper-alloy nails in the United States. While we specialize in AISI-type 304 and 316 stainless
steel, aluminum, brass, commercial bronze, copper, monel and silicon bronze, exotic alloys pose
no problem – provided their mechanical properties are within our manufacturing capabilities.
Call today with your requirements and one of our product specialists will be ready to assist you.
85
SPECIALTY FASTENERS
SPECIALTY TOOLS | Premium Driver Bits
Made in the U.S.A., our new industrial-grade driver bits are specially designed for a
secure fit with the recess of Simpson Strong-Tie ® Swan Secure stainless-steel screws.
Available in both square and six-lobe drive configurations, our bits will outperform
sub-standard imports commonly prone to stripping and cam-out.
Driver Bits – Square Drive
Drive
Bit Length
Item No.
#1
2"
SSBIT1-2
#2
2"
SSBIT2-2
#3
2"
SSBIT3-2
Drive
Bit Length
Item No.
Driver Bits – Six-Lobe Drive
T-15
2"
SSBIT15-2
T-20
2"
SSBIT20-2
T-25
2"
SSBIT25-2
Our new #7 Drill ‘n Drive™ makes pre-drilling, countersinking and driving screws easy –
all without having to re-chuck your drill – just drill, release, flip, lock and drive. The tool
features a built-in hex key for replacing or changing driver and drill bits as well as adjusting
pilot hole depth. A 1⁄8" replacement drill bit and our new T-15 and #1 square driver bits are
included. Made in the U.S.A., with a limited lifetime warranty.
86
Screw Size
Drill Bit
#7
.95"
Countersink
Diameter
Countersink
Angle
Driver Bits
(included)
Item No.
⁄4"
55°
T-15 + #1 SQ.
DRILLDRIVE
1
SPECIALTY TOOLS | Drill ‘n Drive™
SPECIALTY FASTENERS
SPECIALTY PLUGS | Wood Plugs (Ipê)
• Made of high quality Ipê and tapered for ease of use
• For use on decks using the EB-TY® system (first boards, aprons, etc.);
also stairs, railings
Plug Diameter
⁄8"
3
Plug Length
Count per pkg.
Item No.
⁄16 "
100
WDPLUG-100
7
SPECIAL APPLICATIONS | Storm-Panel Screw
• Ideal for attaching storm panels to wood, concrete and masonry
• Save time and money with a single installation
• The screw is made of type 305 stainless steel for good corrosion resistance
Size
Length
Item No.
⁄4"
3 7⁄16 "
SPS25344-KT
1
Each pack contains:
(25) Stainless-steel storm-panel screws 1⁄4" x 3 7⁄16"
(25) 1⁄4" zinc die-cast washered wing nuts
(25) White plastic caps to protect threads after panels are removed
(1) Hex driver bit for panel screws
(1) 0.234" x 4 1⁄2" carbide-tipped drill bit
!
INSTALLATION
1. Drill a hole in the concrete or masonry base material using the drill bit provided.
To pre-drill into wood, use a 3/16" bit
2. Position the panel and drive the screw using the hex driver bit (included).
Drive the screw deep enough so that the bottom of the threads for the wing nut
are slightly below the surface of the panel
3. Secure the panel with the wing nut
4. To remove panels – remove the wing nut, remove the panel and cover
the threads on the screw with the plastic cap
Ph: 800-474-7570, 602-272-8128 Fax: 602-272-8014
Bostitch, Senco, Paslode, Dewalt, Duo-Fast, Fasco, Makita, Max, Porter-Cable, Stan-Tech, Spot Nails, Craftsman, Robertson-Holzer, Power Nail, Porta-Nails, Primatech, Muro, Grabber,
Pam and Milwaukee are registered trademarks of their respective companies and/or parent companies.
87

Catalog: Swan Secure Fasteners (C-SSTSWAN09)

Transcription

Similar documents

kik-step®

Skate Deterrents

Product sheet BBPE050.4A

bis tristar - LUCKINSlive

ZIMA 126-CS-Fabrication.indd

ISE Spec Sheet-Contractor 333 - InSinkErator

2005 Haulmark This Motorhome is amazing as the pictures will

Your enquiries are always welcome. STAINLESS OUTFITTERS 161

CW PDF

Hydro-Filter™ - Phoenix Truckmounts