220ACANE LOADER

220A
125A
CANE LOADER
• Engine net power: 49 kW
• Operating weight: 4 930 kg
• Grapple capacity: 0.42 m2
• Payload: 1000 kg
220A
Pump Displacement
40.6 cc/rev per wheel
Deutz F4L912
Relief pressure
276 bar
4 cylinder, in-line, air cooled with
Flow rate at governed RPM
87.29 L/min per wheel
ENGINE
Model
Configuration
CANE LOADER
integrated blower fan
Governed Power
49 kW
DRIVE MOTORS
Max. torque
230 Nm @ 1600 rpm
Model
Eaton 74318
Type
Axial piston, closed loop
Governed full Power Engine
Speed
2 150 rpm
Max. Rated Speed
2 500 rpm
TRANSMISSION
Aspiration
Naturally aspirated
CHARGE CIRCUIT
Frame Mounting
3 point rigid mounting
Model
Bosch Rexroth Double
Dynamic balancer
With
Type
Gear, Open centre
Sump material
Cast Aluminium
Pump displacement
16 cc/rev
Oil Capacity
9l
Pump Flow @ Governed engine
34.4 l/min @ rpm
Alternator”D” terminal switch
Relief Pressure setting
17 bar
Blower failure warning
warning - triggers horn
Pressure Filter Rating- Beta
Low idle
800 rpm
75 rating
High idle
2 250 rpm
Fuel filtration
Two stage. Spin-on water separa-
WHEEL DRIVE SYSTEM
tor primary, replaceable spin-on
Total wheel drive reduction
67.77
secondary
Drive motor series
#27
Replaceable spin-on paper-type
Wheel torque
12.09 kNm per drive wheel
micro filter- full flow
Wheel RPM @ governed engine
31.7 rpm
Transmission Corner Power
80.3 kW
Oil filtration
13 micron
EXHAUST
Type
Rigid frame mounted stainless
DRIVE WHEELS
steel vertical silencer with short
Drive Tyre Type
All Traction Field & Road - 8 ply with
inner tube
stack pipe outlet
Drive Tyre size
18.4 x 30
AIR CLEANER
Drive Wheel rim
15 x 30, 1 piece
Type
Dual (primary & safety) paper
Drive Wheels Tractive Effort
33.387 kN-machine
element cyclonic canister type with
Road speed
8.7 Km/Hr at governed engine
speed
restriction visual indicator
PRE CLEANER
Drive Wheel Inflation Pressure
1.5 bar
Unladen Ground Pressure - Front
0.43 bar
SYSTEM
Type
Cyclonic dust bowl. Dialy emptying
TAIL WHEEL
requirement
Tail Wheel Tyre Type
High Flotation Implement, 10 Ply
with inner tube
FUEL INLET SYSTEM
Tail Wheel Tyre Size
400 x 15.5
Water separator primary
Tail Wheel rim
13 x 15.5, 1 piece
filter- spin-on
Tail Wheel Inflation Pressure
1.0 bar
Secondary filter- spin-on
Unladen Ground Pressure - Rear
0.95 bar
Frame mounted, 5 microns.
Engine mounted, 5 microns
ENGINE/TRANS.
BRAKES
COUPLING
Service Brake Type
Type
Closed Loop Hydrostatic Wheel
retardation
Bell nylon gear coupling
Park Brake Type
Spring applied , hydraulic release
wet multi disc
DRIVE PUMPS
Model
Eaton 78363
Type
Axial piston, closed loop,
ATTACHEMENT
manual control swash plate
Type
Bell Series 42 Cane
Direct control, foot lonkage
Capacity
0.42 m2
Control
220A
CABIN
BOOM/MAST
Type
CANE LOADER
Crankboom
Type
Integral with steel frame.
No doors
Guarding
HYDRAULIC FAN
guard. Rear engine bay doors
SYSTEM
Type
HD windscreen guard & bonnet
Cooling Fan driven by fixed
displacement gear motor with
SAFETY/ERGONOMICS
Over-centre lock-down latches x2 to
remote combination relief valve/
prevent accidental seat plate tip-up;
free-wheel valve. Motor driven by
Low profile padded seat with lap strap
charge circuit pump - power
seat belt
beyond to charge circuit
WARNING LIGHTS
Alternator/ Fan Belt breakage
HYDRAULIC TANK
Pressure sensor switch-on point:
Type
Integral with tubular frame
Oil Type
Rando HDZ 68 Hydraulic fluid
Capacity
140 l (150 l for system)
OPERATING MASS
Maximum operating temp.
90 deg C @ 45 ambient
Unladen Front
3,230 kg
Unladen Rear
1,700 kg
IMPLEMENT HYD
Unladen Total
4,930 kg
SYSTEM
Shortest Wheelbase
2,458 mm
Fixed displacement open centre
Load distance ahead of front axle
2,500 mm
separate gear pumps with full
Outstretched Tipping load
1,671 kg
flow suction strainer and return
SWL - Payload
1,000 kg
filter filtration
SWL Laden Front
5,247 kg
WO return
SWL Laden Rear
683 kg
SWL Laden Total
5,070 kg
Type
BOOM/MAST
HYDRAULIC FUNCTION
Pump Model
Eaton #26
Pump Type
Gear, open centre, Trans.pump
thru-drive
Pump Displacement
22.5 cc/rev
Relief Pressure setting- down
70 bar
NON-BOOM AUX HYD
FUNCTIONS
Pump Type
Gear, open centre, engine geartrain
drive
Pump displacement
22.5 cc/rev
Pump Flow @ Governed engine
48.4 l/min @ rpm
FUEL TANK
Type
Remote to frame, rear mounted
Capacity (L)
82 l
ELECTRICAL SYSTEM
Voltage
12 V
STEERING SYSTEM
Type
Front wheel hydraulic skid steer via
foot operated treadle control
system
0.25+.1 bar
220A
CANE LOADER
310
(1")
LINE DRAWINGS
6m
4m
1
1m
2 800 (9'2")
2m
R
DE
OA
EL
AN
LC
CY
A4
25
750 (2'5")
2 800 (9'2")
3m
Maximum Implement Lift Height (Centre of pivot)
5 560 (18'3")
5m
460
(1'6")
2 620 (8' 7")
3 260 (10'8")
4 040 (13'3")
0
1 000
(3'3")
1m
2m
3m
1 710 (5'7")
What makes the 220A Cane Loader
a great performer...
• Excellent manoevrability
• Low fuel burn
• Low operating and maintenance costs
• Low capital outlay
• Excellent zone loader
• Low ground pressure
• Simple, strong & reliable
• Increased grab capacity
Tel: +27 11 928 9700
Tel: +49 6631 911 30
Tel: +33 555 89 23 56
Tel: +34 918 796 019
Tel: +7 495 771 20 27
Tel: +44 1283 712 862
E-mail: [email protected] • www.bellequipment.com
All dimensions are shown in millimetres, unless otherwise stated between brackets. Under our policy
of continuous improvement, we reserve the right to change specifications and design without prior
notice. Photographs featured in this brochure may include optional equipment.
SPEC/952/10/10 - 220A Cane Loader
BELL INTERNATIONAL : Tel: +27 (0) 35 907 9431