Stinger™ II Jib Arm - Chapman Leonard Studio Equipment, Inc

Transcription

Stinger™ II Jib Arm
USER GUIDE
Operational Instructions & Specifications
Stinger™ II Jib Arm
© 2004 Chapman/Leonard Studio Equipment, Inc.
Revision 8 - 7/2008
It is Chapman/Leonard’s goal to provide the best camera support equipment with
exceptional Customer Service. Therefore, we are compiling this User Guide to aid in
the reordering of Replacement Parts for your Leased Equipment.
For any questions regarding this User Guide, please contact
Customer Service at 888-883-6559 or 818-764-6726.
Chapman/Leonard Certified Locations:
MAIN OFFICE
12950 Raymer Street,
North Hollywood, CA 91605
888-883-6559
or 818-764-6726
Fax: 818-764-6730
or 818-764-4347
Texas
866-848-2602
or 604-299-0913
Fax: 604-299-0926
1901 E. 51st Street, Suite 38
Austin, Texas 78723
512-473-0084
or 888-758-4826
Fax: 512-473-0042
Canada
8301 Eastlake Drive
Burnaby, British Columbia
V5A 4W2 Canada
Louisiana
660 Distributors Row Suite C & D
Elmwood Business Park
New Orleans, LA 70123
UK and Europe
Chapman Leonard Studio
Equipment, Ltd.
Unit 5
Kingley Park Station Road
Kings Langley, Herts
England WD4 8GW
01923 265 953
Florida
9460 Delegates Drive
Orlando, Florida 32837
888-758-4826
888-337-8243
or 407-851-3456
Fax: 407-855-1653
Use a Qualified Operator. For Assistance Please call our 24 hour Customer Service at 1-888-883-6559.
© 2004 No part of this manual may be reproduced or electronically transmitted without
the written permission of Chapman/Leonard Studio Equipment, Inc.
1
Revision 8 - 7/2008
CONTENTS
2
Revision 8 - 7/2008
3
Features of the Stinger Jib Arm
4
Transporting
5
Mounting Bases
6
Pedolly Mount
7
Overslung to Underslung Mode
10
Adding/Removing Glide Head
11
Adding/Removing Arm Extensions
14
Configurations 17
Mounting Options
Features of the Stinger II Jib Arm
Item #12550
• Comes Assembled (In Full Configuration Upon Request) and Ready for Use Allowing Quick Setup
or in its own special Cart for easy transport and storage in the smallest configuration of the arm.
• Every Rental comes with all the parts for any configuration.
• See Page 14 for all configurations of the Stinger II Jib Arm.
• Compact and Lightweight Arm.
• Stinger Arm Glide System Allows up to 2 ft. of Horizontal Travel.
• Black Anodized Arm for Easy Maintenance.
• Works on Super PeeWee IV, Hustler and Hybrid Camera Dollies, along with a Variety of Bases.
• Precision Design for Rigidity without the Need for Cabling System.
• A Variety of Counter Balance Weights Available from 5 lbs. to 25 lbs.
• Precision Design Weights are Contoured and Shaped on a Radius to Follow the Arc of the Arm.
• Stinger Arm Glide System has Drag Control.
• Cushioned Stops with Dampening Points at Top and Bottom Travel of the Arm.
• Fluid Dampening System Resulting in Zero Backlash.
• 360 Degree Continuous Pan Travel.
• The Stinger Jib Arm has a Maximum Reach of 12 feet (from the Fulcrum).
• Works with a Variety of Heads (Including Remote Camera Systems).
• Designed to Work within Tight Areas.
Removable Slider Weight
for Fine Tune Balancing
Mitchell Mount
Rigid without the need for a Cabling System
Leveling Rod
Tilt Drag Control
Glide Head
5, 10 & 25 lbs,
Contoured Weights
Require Less Space
During Movement
Compatible with
Variety of Heads
Pan Drag Control
In this Example: Mounted on a Chapman Hybrid II Plus Camera Dolly
see page 17 for other Mounting Options
3
Revision 8 - 7/2008
Transporting the Stinger II Jib Arm
Front
Mobile Storage Base for the Stinger II Jib Arm
(with Mitchell Mount.)
For One Man Mounting and Assembly,
a Mobile Storage Case comes with every
Stinger Jib Arm. When in its case, there is
space below the stored Stinger Jib Arm that
enables rolling a dolly underneath.
A Mobile Weight Case with 425 lbs. of
Weights comes with every Stinger Jib Arm.
Each Arm comes with four 5 lbs. Weights,
two 10 lbs. Weights,
and seventeen 25 lbs. Weights.
4
Revision 8 - 7/2008
Mounting Bases for the Stinger II Jib Arm
Standard High Post Mount setup.
Hybrid dolly with Center Post kit.
Stinger II Arm in the Cam-Mate configuration.
5
Revision 8 - 7/2008
Pedolly Mount for the Stinger II Jib Arm
The Pedolly with its column removed and a Center Post
Insert attached.
Before mounting the Stinger Jib Arm on the
Center Post Insert, all legs MUST be in the
45 degree configuration. This will provide
maximum stability for the base.
Use the special Castle Ring Wrench to tighten
the Castle Ring.
6
Revision 8 - 7/2008
To switch the Glider from Overslung mode to
Underslung mode, begin by removing the
Rubber Cover (viewed from below).
Pull down on the Rubber Cover to remove it
from the Gliding Head.
Next remove the Locking Ring.
7
Revision 8 - 7/2008
Separate the Mitchell Mount Head from the
Glider Mechanism.
The Glider Mechanism shown with the Mitchell
Mount Head removed.
Position the Mitchell Mount Head below the
Glider Mechanism.
8
Revision 8 - 7/2008
Raise the Mitchell Mount Head until its threads
become visible above the Glider Mechanism.
Attach the Locking Ring to the Mitchell Mount
Head.
Replace the Rubber Cover on the Glider
Mechanism. The Glider is now ready to use.
9
Revision 8 - 7/2008
Adding/Removing the Glide Head
Whenever extensions are added/removed from
the Stinger Jib Arm, the 2 ft. Glider should be
removed first. Begin by removing the Indexing
Quick Release Pin.
Remove the retaining screw from the 2 ft. Glider
while supporting the Glider to prevent it from
falling to the ground.
The 2 ft. Glider can now be pulled from the arm.
10
Revision 8 - 7/2008
At this point, extensions of the Arm may be
safely added or removed.
The Weight Tray Knob (pictured below) for the
Weight Tray Rod may be stored on the Arm
(pictured at left) when weights are being added
or removed.
Before attempting to add or remove an arm
extension, remove all weights from the Tray.
11
Revision 8 - 7/2008
Warning! Before adding or removing any
section of the Stinger Jib Arm, the front
Glider Section MUST first be removed to avoid damaging the arm.
The Splice Retainer Bar with Cam Lock
ensures a tight fit between sections of the
arm. This is essential to maintaining the rigidity
and stability of the Stinger Jib Arm while in
operation.
When attaching an arm section, loosen the
Socket Head Cap Screws enough to lift the
Splice Retainer Bar over the Screw Cam Lock.
Push down on the Splice Retainer Bar until it
is flush against the arm section. The Screw
Cam Lock may have to be turned slightly to
allow the Splice Retainer Bar to fit properly
against the arm.
Tighten the Socket Head Cap Screws, then
loosen both Socket Head Cap Screws one full
turn. This is enough to allow the fit between the
arm sections to be adjusted.
12
Revision 8 - 7/2008
Next, tighten the Screw Cam Lock to draw the
arm sections together. Less than half a turn of
the Screw Cam Lock is necessary.
As shown here, the visible gap between the arm
sections has been eliminated.
The final step is to tighten both Socket Head
Cap Screws. Excessive torque is not required.
Disassembling the Stinger Jib Arm sections is
simply the reverse of the above procedure.
Warning! Before adding or removing any
section of the Stinger Jib Arm, the
front Glider Section MUST first be removed to avoid damaging the arm.
13
Revision 8 - 7/2008
14
Revision 8 - 7/2008
R
lbs.
MH = 80” (6’ 8”)
MR = 100” (8’ 4”)
MP = 209 lbs.
BW = 65 lbs.
BAW = 284 lbs.
1 Foot Section - Front
1 Foot Section - Rear
MOW = Maximum Operating Weight of unit.
BR = Balance Ratio. (Determine the weight required in bucket to
balance a Payload after arm has been balanced.)
UW = Unit Weight.
150”
Overall
6 Inch Section - Rear
No Added Sections
MOW = 812 lbs.
BR = 2:1
UW = 215.5 lbs.
MOW = 858 lbs.
BR = 1.7:1
UW = 219 lbs.
Stinger II Configuration #3
Overall
144”
MH = 80” (6’ 8”)
MR = 100” (8’ 4”)
MP = 166 lbs.
BW = 85 lbs.
BAW = 300
MH = Maximum Height (From inverted camera Mitchell mount to base. Total height would be in addition to maximum height of dolly arm.)
MR = Maximum Reach. (As measured from center post to camera Mitchell mount.)
MP = Maximum Payload.
BW = Bucket Weight for balanced arm. (No Payload.)
BAW = Balanced Arm Weight. (No Payload.)
R
126”
Overall
MOW = 799 lbs.
BR = 2:1
UW = 203 lbs.
MH = 74” (6’ 2”)
MR = 88” (7’ 4”)
MP = 166 lbs.
BW = 105 lbs.
BAW = 308 lbs.
Stinger II Configurations
For Configurations not shown in this brochure, or
questions regarding a special setup, Please contact
a Chapman/Leonard Service Representative.
R
R
162”
Overall
MOW = 819 lbs.
BR = 2:1
UW = 222.5 lbs.
168”
Overall
MOW = 861 lbs.
BR = 1.75:1
UW = 227 lbs.
MH = 98” (8’ 2”)
MR = 124” (10’ 4”)
MP = 164 lbs.
BW = 90 lbs.
BAW = 325 lbs.
2
1
1
6
Foot Section - Front
Foot Section - Front
Foot Section - Rear
Inch Section - Rear
6 Inch Section - Rear
UW = Unit Weight.
180”
Overall
MOW = 829 lbs.
BR = 2:1
UW = 235 lbs.
MH = 92” (7’ 8”)
MR = 112” (9’ 4”)
MP = 204 lbs.
BW = 65 lbs.
BAW = 292 lbs.
MH = 92” (7’ 8”)
MR = 112” (9’ 4”)
MP = 166 lbs.
BW = 90 lbs.
BAW = 313 lbs.
R
R
R
15
Revision 8 - 7/2008
16
Revision 8 - 7/2008
R
R
186”
Overall
MOW = 863 lbs.
BR = 1.8:1
UW = 238.5 lbs.
198”
Overall
MOW = 836 lbs.
BR = 2:1
UW = 246.5 lbs.
MH = 110” (9’ 2”)
MR = 148” (12’ 4”)
MP = 131 lbs.
BW = 125 lbs.
BAW = 375 lbs.
210”
2 Foot Section (x2) - Front
1 Foot Section (x2) - Rear
2 Foot Section (x2) - Front
UW = Unit Weight.
Overall
MOW = 811 lbs..
BR = 2.24:1
UW = 250 lbs.
MH = 104” (8’ 8”)
MR = 136” (11’ 4”)
MP = 159 lbs.
BW = 100 lbs.
BAW = 347 lbs.
MH = 98” (8’ 2”)
MR = 124” (10’ 4”)
MP = 194 lbs.
BW = 75 lbs.
BAW = 314 lbs.
R
R
R
R
The Stinger can be mounted on these Chapman/Leonard products:
41"
41"
40"
591/2"
461/2"
(1.4 m)
(1.4 m)
(1.4 m)
(1.5 m)
(1.6 m)
LenCin ®
Pedolly ®
(With Center Post Insert)
(With Center Post Insert)
(With High Post Kit)
MAXIMUM PAYLOAD =
1,100 lb. (499 kg)
Operating Weight of Unit =
245 lb. (111 kg)
Minimum Carrying Weight
of Unit = 164 lb. ( 75 kg)
MAXIMUM PAYLOAD =
1,100 lb. (499 kg)
305 lb. (139 kg)
of Unit = 224 lb. (102 kg)
MAXIMUM PAYLOAD =
1,100 lb. (499 kg)
386 lb. (175 kg)
of Unit = 280 lb. (127 kg)
PeeWee®
Super PeeWee ® IV
MAXIMUM PAYLOAD =
350 lb. (159 kg)
391 lb. (178 kg)
of Unit = 295 lb. (134 kg)
+49"
54"
54"
(1.25 m)
(1.5m)
(1.5m)
Hy Hy ®
Hybrid
(With High Post Kit)
Hustler
MAXIMUM PAYLOAD =
1,900 lb. (862 kg)
501 lb. (227 kg)
of Unit = 395 lb. (179 kg)
Hustler IV
(With 7.5" Riser)
MAXIMUM PAYLOAD =
2,900 lb. (1,316 kg)
325 lb. (148 kg)
of Unit = 260 lb. (118 kg)
MAXIMUM PAYLOAD =
500 lb. (227 kg)
454 lb. (206 kg)
of Unit = 420 lb. (191 kg)
MAXIMUM PAYLOAD =
750 lb. (340 kg)
505 lb. (229 kg)
of Unit = 465 lb. (211 kg)
Virtually Maintenance Free Arm
• Wipe down the rollers each day.
For Configurations not shown in this brochure, or questions regarding a special
setup, Please contact a Chapman/Leonard
Service Representative.
The reach of the Stinger Jib Arm offers an
incredible range of movement.
17
Revision 8 - 7/2008

Stinger™ II Jib Arm - Chapman Leonard Studio Equipment, Inc

Transcription

Similar documents

SaeboFlex / SaeboReach Brochure

Softub T-220 - Softub of the Carolinas

K9 SUPERFUEL TM Human Grade Ingredients

New York Arm Wrestling® and Mulcahy`s Pub Presents the

SC-2300 spec

classic service van for ford transit

recycling done right - Vancouver

LGOBO SALE SHEET

Fokker DRI Tri-plane - Airdrome Aeroplanes

How I survived teaching my first online course