to begin downloading PDF document.

11 th Edition
Bits & Spurs Catalog
Chem Tac, Inc.
Fredericksburg, Texas
Toll Free Orders: 1-800-654-8547
Toll Free Fax:
1-800-900-7599
Bit Terminology
1-800-654-8547
CHEM TAC
BIT TERMINOLOGY
The following information is designed to assist both you and your customer in making the best
possible bit selection. We believe, however, that one factor is paramount to the best possible bit
selection. Good horsemanship requires proper use of all the aids used to cue the horse to perform.
This includes the type of hands that initiate the pull of the bit.
Basic Concepts to remember when selecting a bit:
•
•
•
•
•
Mouthpieces can be made of different types of metals, hard rubber or flexible rubber. Each
yields a different effect.
The thicker the mouthpiece the milder the bit, because the bit pressure is spread over a larger
area. The thinner the mouthpiece, the more severe the bit.
The length of the shank dictates the amount of curb pressure and leverage or pressure applied
to the chin groove and the poll of the horse.
There are various mouthpiece configurations. Each mouthpiece helps to determine the
function of a bit. (See mouthpiece descriptions for additional explanation).
Always remember, to achieve the most effective results from bitting a horse for a specific use, understand proper fit and function.
Basic Bit Types
Full Cheek Snaffle
For the traditional Hunter look, the Full Cheek Snaffle is available in a variety of mouthpieces. Each mouthpiece determines
the function of the bit. The full cheeks prevent the cheeks from pulling through the horse’s mouth. And, when fitted with
bit loops that attach to the bridle, the bit becomes more stable for increased lateral control.
Kimberwick
Commonly seen today in the English events of breed association horse shows, the Kimberwick uses a curb chain for
increased leverage. The Uxeter Kimberwick has two rein slots, each changing the desired result. The upper slot is used
to increase the pressure on the tongue, while the lower slot is used to increase leverage and curb chain pressure.
Pelham
The Pelham bit, with its double set of reins, combines the function of a snaffle and the action of a curb bit. The top rein
provides snaffle pressure to the tongue and corners of the mouth, while the bottom rein increases leverage and curb
chain pressure.
Weymouth and Bradoon
For the finished dressage horse, the full or double bridle uses both the snaffle action of the Bradoon and the curb action
of the Weymouth to encourage collection with softness through the bridle. Both bits working independently of each
other allow the rider to use the most subtle cues.
Eggbutt Snaffle
A very mild bit, the Eggbutt Snaffle is designed wide enough to be gentle on the bars and will not pinch the horse’s mouth.
Ring Snaffle
A functional bit for all types of training, the loose rings of a Ring Snaffle help increase the bit movement, promote
salivation and keep the mouth soft and the body supple.
Dee Ring Snaffle
One of the most basic forms of bitting, the Dee Ring Snaffle is a relatively mild snaffle that comes in a variety of
mouthpieces, Whether you are starting a horse, or just going back to the basics, this bit helps with lateral movement
while achieving suppleness from jaw to tail.
2
Printed on: 02/28/14
Bit Terminology
1-800-654-8547
Tom Thumb Snaffle
One of the most basic shanked type snaffle bits, the Tom Thumb Snaffle serves as an excellent transition bit from a
Ring Snaffle to a longer shanked snaffle or to a Curb Bit. This bit uses a small amount of curb pressure or leverage.
The loose cheeks move independently allowing for more lateral flexibility.
Double Rein Bit
The Double Rein Bit, as its name implies, can be used with four reins. This bit is also termed “Cowboy Pelham”.
For normal use, the reins are attached to the shanks. But with the dee rings located at the mouthpiece, the second
set of reins helps to achieve more snaffle action similar to the English Pelham bit.
Curb Bit
The Curb Bit, one of the major bit types, is considered a leverage bit because of the action of the curb chain. When
the reins are pulled and the curb chain is engaged, it applies pressure to the chin groove. The term Grazing Bit is
commonly referred to as a Curb Bit with the bit shanks bent back to allow the horse to graze.
Gag Bit
The sliding action of the Gag Bit applies pressure to the lips and corners of the mouth. This action along with the
give and take of the rider’s hands help elevate the horse’s front end. This bit is commonly used by barrel racers
for proper body position while turning the barrel. Some Gag Bits offer variable rein loops for greater lateral pull.
Hackamore
The Hackamore is designed to create pressure just above the soft tissue of the nose. And when the curb chain is
engaged it also applies pressure to the chin groove. Used by ropers and barrel racers, the Hackamore is designed
for getting quick stops from forward motion. Hackamores are available with a variety of nosebands from moderate
to severe. They include fleece lined leather, flat leather, rubber, bicycle chain covered with rubber or plastic, laced
leather, braided leather or rope. When combined with a mouthpiece, the Hackamore gains more lateral control.
Basic Mouthpieces
Low and Medium Port
These mouthpieces are relatively mild. The curvature of the port allows for tongue relief (applying minimal pressure
across the width of the tongue). And, with rotation of the bit, the mouthpiece does not apply palate pressure
(pressure applied to the roof of the mouth). Both mouthpieces will, however, apply pressure to the bars of the
mouth that increase in severity as the mouthpiece diameter becomes smaller.
High Port
Just as the Low and Medium Port mouthpieces provide tongue relief and apply pressure to the bars of the
mouth, so does the high port.
Roller
Also termed as a “Cricket” mouthpiece, the Roller is commonly made of copper and can be combined with Medium
and High Ports, Snaffle Mouths, Halfbreeds and Spades. This mouthpiece will apply tongue pressure as it lays
across the tongue. It is an ideal mouthpiece to pacify nervous horses and at the same time promotes salivation.
Mullen Mouth
This mouthpiece provides some tongue relief and does apply bar pressure. It is recommended for horses that
dislike palate pressure.
Sweetwater
This mouthpiece does not apply tongue pressure and is recommended for horses with an injured tongue, or horses
that dislike tongue pressure. It does, however, apply bar pressure.
Correction
The Correction mouth, when used as part of a leverage bit, can be considered severe because it applies tongue
pressure at the flexible joint of the port and bar pressure.
Snaffle
The snaffle configuration by itself is a mild bit and one of the most universally used mouthpieces. It can be thick
and mild on the bars and tongue when covered with rubber, or severe if used as a thin twisted wire mouthpiece.
It an be combined with many variations such as a Copper Roller, Dr. Bristol, Dog Bone, or Lifesaver mouthpiece.
3
Printed on: 02/28/14
Bits
1-800-654-8547
RUSH QTANNA BIT
RR-077
This shank bit provides an indirect curb
rein action designed to be used with a
curb strap attached to the purchase.
The broken mouthpiece on this bit will
apply more pressure specifically to
the tongue than a traditional curb bit;
however, the combination of the fixed
cheek and fixed rein apply mild pressure
to the bars of the mouth, chin and poll.
Sweet Iron Comfort Snaffle with Copper
Roller Mouth, This mouthpiece is made
of polished Sweet Iron which naturally
oxidizes or rusts. It has a sweet taste
and promotes salivation.
MARTHA JOSEY TWISTED
WIRE HACKAMORE
RR-M6308-8 3/4
JIM PRO BIT
RR-JM17
JOSEY GO AROUND BIT
RR-J4717
Gag Bit sweet iron, low port mouth
piece that is very comfortable to
many horses. The placement of
the stops on the shanks help the
mouthpiece stay in place for the right
amount of gag. This bit can really
package a horse up, keeping him
collected and snappy in the turns.
Stainless Steel ring with twisted
wire mouthpiece and rope nose.
The rope nose has been lowered to
give more action between the nose
and mouth. The chain curb gives
a hackamore action and feel by
releasing the pressure on the bars.
Rings-3" Mouth-5".
Printed on: 02/28/14
MARTHA JOSEY
DOGBONE HACKAMORE
RR-M6317-8 3/4
MARTHA JOSEY
DOGBONE HACKAMORE
RR-M6317-7
Combination Hackamore features a
twisted wire, snaffle mouthpiece and
a rope noseband. Being well balanced,
equipped with an 8-3/4” shank, is ideal
because pressure is evenly distributed on
the nose, bars, and corners of the mouth
and curb.
TRAINING SNAFFLE
RR-1012
Barrel Gag for horses that need to
learn to give to light bit pressure, or
horses that are not used to giving to
bit pressure at all, like colts. Helps
horses and colts learn how to give to
the lightest amount of bit pressure and
understand the signals clearly without
severity to the horse’s mouth.
Combination hackamore features
a 3-piece twisted wire, dog bone
snaffle mouthpiece and a rope
noseband. Being well balanced,
equipped with an 7” shank, is
ideal because pressure is evenly
distributed on the nose, bars, and
corners of the mouth and curb.
WONDER BIT
RR-1027C
3-Piece Sweet Iron with Chain
Center This mouthpiece allows the
bars to break at a steeper angle to
apply pressure to the outside edge
of the bars for a new feel and more
control.
Combination hackamore features
a 3-piece twisted wire, dog bone
snaffle mouthpiece and a rope
noseband. Being well balanced,
equipped with an 8-3/4” shank,
is ideal because pressure is evenly
distributed on the nose, bars, and
corners of the mouth and curb.
JUNIOR COWHORSE BIT
RR-1105
Junior cowhorse bit with large twisted sweet
iron mouth piece, 5” cheeks. A cheek with
growing popularity. The short gag action
collects a horse very well and helps to get
his legs underneath him and his rear end
down. The large twisted sweet iron snaffle
is very popular and adds some “bite” to the
relatively light bit. Great for horses that try
to lug on the bit or need a little more control.
4
MARTHA JOSEY TWISTED
WIRE HACKAMORE
RR-M6308-7
Combination Hackamore features
a twisted wire, snaffle mouthpiece
and a rope noseband. Being well
balanced, equipped with a 7” shank,
is ideal because pressure is evenly
distributed on the nose, bars, and
corners of the mouth and curb.
TRAINING SNAFFLE
RR-1011
3" Stainless Steel rings with 5" sweet
iron bradoon mouthpiece and rope
nose. The rope nose has been lowered
to give more action between nose
and mouth. The chain curb gives a
hackamore action and feel by releasing
the pressure on the bars. The smaller
mouthpiece aids in softening the mouth
and adds more control.
JUNIOR COWHORSE BIT
RR-1107
Junior cow horse bit, 3/8” sweet iron
mouthpiece, 5” cheeks. This cheek
gets more popular everyday. It helps to
get your horse’s legs underneath him
and his rear end down. The short gag
action collects a horse very well. The
smooth sweet iron snaffle mouthpiece
is our most popular and is light enough
to pull young colts around without
damaging their mouth.
Bits
JUNIOR COWHORSE BIT
RR-1107-6
Junior Cowhorse bit with a sweet iron
snaffle mouthpiece and 4” cheeks.
A very popular short cheek piece.
It helps to get your horse’s legs
underneath him and his rear end
down. The short gag action collects a
horse very well.
1-800-654-8547
JUNIOR COWHORSE BIT
RR-1117
JUNIOR COWHORSE BIT
RR-1109
Junior Cowhorse bit with large twisted
copper mouthpiece and 5” cheeks, a
cheek with a growing popularity. The
short gag action collects a horse very
well and helps to get his leg under him
and his rear end down.
JUNIOR COWHORSE BIT
RR-1112
The short gag action collects a horse
very well. The three piece mouth adds
some bite for horses that are heavy on
the bit or need a little more flex. 5”
mouth and 7” shank.
The small chain mouth conforms
well to the bars and tongue making it
comfortable for your horse to pack. This
bit has light control and is excellent for
training or relaxed pleasure riding. 5”
mouth and 7” shank.
D-RING BIT
RR-1240
JUNIOR COWHORSE BIT
RR-1117-6
Twis t e d d o g b o n e m o u t hp ie c e .
Extremely good if you need help
getting your horse’s legs underneath
him and his rear end down. The short
gag action collects a horse well. The
three piece mouth adds a little more
bite to this low leverage bit.
WONDER BIT
RR-1305
With large twisted sweet iron snaffle
for horses that need a little extra
control. Used in a back and forth
method, this bit will lighten a horse
up and back him off the bit. 7" shank,
5" mouth.
FULL CHEEK SNAFFLE
RR-1202E
JUNIOR COWHORSE BIT
RR-1166
3/8” sweet iron mouth piece. 3” dee
designed to apply pressure to a horse’s
lip on the opposite side of the face.
This, coupled with the larger smooth
mouthpiece, makes it one of our most
popular bits.
Junior Cow horse, twisted 3-piece ¼”
sweet iron bradoon mouth with 6”
cheeks. A low leverage gag, excellent
for horses with a lot of natural rate. An
excellent mouthpiece for lifting your
horse’s head and tucking his head at
the same time.
WONDER BIT
RR-1327
Wonder Bit with 3 piece sweet iron
chain link snaffle offers light control and
should be used with a curb chain. The
mouthpiece breaks closer to the bars
creating a greater angle and touching
new nerves for more control. It has a
slight amount of tongue pressure. 7"
shank, 5" mouth.
WONDER BIT
RR-1307
Wonder Bit with 3/8" sweet iron
snaffle. This bit helps to pick a horse
up and hold the shoulder until the turn
is made. 7" shank, 5" mouth.
1/2” oval port mouthpiece, 3” dee
applies pressure to the lip on the
opposite side of the face from the rein
you pull. With its limited travel, this
is an excellent mouthpiece for colts
or light mouthed horses. It applies a
slight amount of tongue pressure for a
good head set and will help pacify a
nervous horse.
HALF CIRCLE GAG
RR-1407
5" sweet iron snaffle. One of the basic
bits for training. The snaffle is easy on
a horse's mouth and when used with a
tie down will assist in head placement.
5
Printed on: 02/28/14
Bits
1-800-654-8547
DOG BONE GAG
RR-1417
Half Circle Gag with 3/8” 3-piece
twisted wire with dog bone. Very
popular with trainers to help set the
head correctly on a young horse.
Mouthpiece adds more control with bar
contact and some tongue pressure to
help set horse’s head. This bit has a
surprising amount of control.
TENDER TOUCH BIT
RR-1506
Tom Thumb bit with double twisted
sweet iron and copper snaffle. 7”
shank and 5” mouthpiece.
TOM THUMB JR. BIT
RR-1517S
Tw i s t e d w i r e w i t h d o g b o n e
mouthpiece and 6” cheeks. Excellent
for leaving ring snaffle while training
and an extremely good choice for
older, well-bitted horses. If your horse
has a good mouth, keep it good with
a good bit.
TENDER TOUCH BIT
RR-1505
EASY TOUCH BIT
RR-1502
Tom Thumb bit with large sweet iron
twisted snaffle. 7” shank and 5”
mouthpiece.
Tom Thumb bit with 3/8” sweet
iron snaf fle. 7” shank and 5”
mouthpiece.
TOM THUMB
RR-1502S
Tom Thumb Jr. with sweet iron
snaffle. 6" shank, 5" mouth.
TENDER TOUCH BIT
RR-1508
TENDER TOUCH BIT
RR-1511
Small twisted mouthpiece gives a little
more control than a ring snaffle. This is
an extremely good shank. Low leverage
but adds some curb pressure. Packs
easily. This mouthpiece is one of the
more severe ones.
JUNIOR COW HORSE BIT
RR-1527
Tender touch with a copper snaffle
mouthpiece and a chain center. Low
leverage shank for an easy control
horse that needs a little more control
than a ring snaffle. The Tom Thumb
has been around for years.
Bradoon mouthpiece, low leverage
shank for an easy control horse that
needs a little more control than a
ring snaffle. Young horses as well as
tender mouthed horses will accept this
mouthpiece well and the small mouth
will give you more control.
SWIVEL BIT
RR-1607
Swivel bit with 3/8” sweet iron
mouth piece. Features a swivel top
ring that keeps the headstall in place
when turning, short shank for side
pull action and large rings for lighter
control. The mouthpiece is one of the
most popular.
6
Printed on: 02/28/14
TOM THUMB JR. BIT
RR-1516S
Tom Thumb snaffle is an excellent
bit for reining, pleasure and young
pleasure horses. The loose jaw feature
allows side pulling and leverage on
either rein. Also makes this a milder
bit for training purposes
SWIVEL BIT
RR-1617
The swivel top ring keeps the headstall
in place while turning. The twisted
dog bone mouthpiece breaks over the
tongue to give new feel. Gag action
helps collect the horse for better
maneuverability and stops.
Bits
1-800-654-8547
TENCY GAG
RR-1810
Tency gag with extra small stainless
steel twisted snaffle. For the more
experienced rider because it will "sore
up" the corners of the horse's mouth.
Ideal for a stiff horse. Good training bit.
BEWARE: Heavy hands will make this
a severe bit.
SEVEN BIT
RR-1921
EASY TOUCH BIT
RR-1817
Easy Touch Bit with twisted
dog bone mouth piece.
Seven Bit, solid cheek pleasure horse,
1/2” wide medium copper port mouth
piece. Has 7” Trail Riders Cheek that
is designed for effective communication
and comfort for horses that spend hours
under the saddle. Features include: low
leverage, swept bank shanks (no lipping),
short purchase for quick release and
loose rein rings for less diagonal pressure.
This mouth piece provides more tongue
relief for a wide sensitive tongue.
SEVEN BIT
RR-1944S
One of our most popular mouthpieces.
The long shank and mouthpiece give
this bit a lot of lift. The cheek is long
enough for good leverage control while
the mouthpiece works on the outer
corners of the bars for a new feel and
adds plenty of tongue pressure for a
good head set. 3/8” Sweet iron high
port 5” mouth and 7” shank.
COMBINATION ROPE NOSE
HACKAMORE
RR-2111
With sweet iron bradoon snaffle,
works off a horse’s nose instead of his
mouth. As you pick up on the reins,
light pressure goes to the mouthpiece,
keeping your horse light in the mouth.
The rings can be snapped to the bit
ring like a snaffle, or tie the rope rings
together. Can tune up a mature horse.
3” rings, 5” mouth.
JR. CURB GAG BIT
RR-2208
Jr. Curb Gag with small sweet iron
twisted snaffle. Excellent for colts
following ring snaffles because of
the light or lowered leverage 6”
shank. Used in early training when
moderate curb action is desired. Has
a moderate severe mouth for training.
JOHNSON HACKAMORE BIT
RR-2812
Johnson hackamore bit with 7-1/2”
cheeks designed by a leading barrel
racing trainer. Excellent training or
performance bit. Long gag action delivers
plenty of lift as well as control. Rope nose
conforms well and works on the bridge
of the nose for rate and control. Chain
mouth is superior in this bit to lessen the
bar pressure and add tongue pressure to
help set horse’s head and help provide
the flex you need to turn your horse at
the performance level.
JUNIOR CURB GAG BIT
RR-2210
Features a stainless steel small
twisted mouth piece which can be
severe and adds lots of control. Do
not tie a horse with this bit.
MCNABB TWISTED SHANK
LIFESAVER BIT
RR-250-56CR
This Twisted Shank Lifesaver gentle
mouthpiece is suitable for all horses,
especially those transitioning from
the snaffle to the bridle. The O-Ring
mouthpiece helps to keep the horse’s
at tention and the c opp er r ing s
encourage salivation. Cheek pieces
move independently for shoulder
control. Seven style shank prevents the
horse from “lipping” at the bit.
ROPE HACKAMORE SIDE PULL
RR-2702
Combination rope nose hackamore side
pull with 3/8” sweet iron mouth piece.
REINING BIT
RR-3005
Stainless Steel reiner bit with
large sweet iron twisted snaffle. 7"
shank, 5" mouth.
REINER BIT
RR-3007
Stainless Steel reining bit. 7” shank
with die cast snaffle mouthpiece.
7
Printed on: 02/28/14
Bits
1-800-654-8547
WARNER
PONY HACKAMORE
RR-3200P
REINER BIT
RR-3009
Stainless Steel reining bit. 7” shank
with small twisted Copper snaffle
mouthpiece.
JIM WARNER HACKAMORE
RR-3200-8
Hackamore. Medium plus leverage for good
control and rate. Notice how well the nose
floats when you pull the shanks but will not
drop down. Also, the shanks swivel for better
flex. It’s tempting to call this a shanked side
pull but it has too much control and rate.
Rope nose for more control.
Pony hackamore. Medium plus leverage
for good control and rate. Notice how
well the nose floats when you pull the
shanks but will not drop down. Also,
the shanks swivel for better flex. It’s
tempting to call this a shanked side pull
but it has too much control and rate.
Rope nose for more control.
WESTERN REINER BIT
RR-3201
Western Reiner with 1/2” copper
mouth piece.
WESTERN REINER BIT
RR-3214
One of the nicest medium control shanks
ever made. Excellent balance and will not
pinch. Can be ridden with a 4-rein to train.
Mouth is one of the least severe snaffles.
The limited travel keeps the snaffle from
excess pressure on the outside bars. The
roller, while acting as a pacifier for the
nervous horse, also applies light tongue
pressure for a better head set.
WESTERN REINER BIT
RR-3212
WESTERN REINER BIT
RR-3202
Stainless Steel reining bit. 7” shank
with sweet iron snaffle mouthpiece.
We s t e r n r ein e r bit wit h chain
mouthpiece. There is no bar pressure
because the chain works on the
corners of the mouth. Ideal for a horse
that fights his head when a rider pulls
on the bit. Good for older horses or
colts. 8” shank, 5” mouth.
WESTERN REINER BIT
RR-3256
WESTERN REINER BIT
RR-3218
Stainless steel reining bit. 7" shank with
sweet iron Mullen mouthpiece.
WESTERN REINER BIT
RR-3220
With sweet iron medium port
similar to the ported mullen. The
narrower port gives this bit a
somewhat softer action. 8” shank,
5” mouth.
With sweet iron snaf fle Life-Saver
mouthpiece. This bit is a good transition
bit from the ring snaffle to one with curb
action. The half-ring on the cheeks allows
a second pair of reins for martingales or
draw reins. The Life-Saver mouthpiece
is an excellent headsetting bit for young
horses or may be used on hard to handle
horses for maximum control. 8” shank,
5” mouth.
8
Printed on: 02/28/14
WESTERN REINER BIT
RR-3216
Stainless Steel training bit, 8-1/2”
shank with a unique sweet iron port
that has the same diameter across
the bars of the horse.
BARREL BIT
RR-3502
With 3/8" sweet iron snaffle for light
mouthed horses who need flex at
the poll. The swivel sides allow the
rider to get the horse's nose in the
turn. 5" shank, 5" mouth.
Bits
ROPE NOSE GAG BIT
RR-3607S
JUNIOR SHOW BIT
RR-3502S
Short Shank Jr. Show Bit with 3/8”
sweet iron snaffle mouth. Great looking
and versatile! The larger 2” rein ring
with slight gag action also provides poll
press to collect for better control and
stops. 4-1/2” shank, 5” mouth.
GAG BIT
RR-3608
Stainless Steel gag with 7"
shank and small twisted sweet
iron mouthpiece.
BARREL BIT
RR-3520
GAG BIT
RR-3605
Barrel Bit with 1/2” medium port
mouth piece.
Stainless steel training bit with
7” shank. Three piece sweet iron
mouthpiece with copper roller.
With sweet iron snaffle, the rope
nosepiece gives a “soft” feel to this
bit and increases effectiveness. 8”
shank, 5” mouth.
Stainless Steel gag with 7" shank and
large twisted sweet iron mouthpiece.
GAG BIT
RR-3624
ROPE NOSE GAG BIT
RR-3608S
GAG BIT
RR-3612
The rope nosepiece gives a “soft” feel
and the small twisted snaffle will pick
a horse up and hold the shoulder.
Stainless Steel gag with 7" shank and
chain mouth.
“MONEY MAKER” BIT
RR-40X17
SHORT SHANK REINER BIT
RR-3719
1-800-654-8547
REINER CORRECTION BIT
RR-3725
Stainless Steel correction bit with 7”
shank. Three piece stainless steel
correction mouthpiece.
With 3/8" snaffle mouthpiece. A
basic training and/or competition bit.
The Copper mouthpiece will keep a
horse's mouth moist and usable. 8"
shank, 5' mouth.
GRAZING BIT
This 3-piece bit is very versatile and works RR-4018
great on most horses. Commonly used on Stainless steel “C” bit with 5” shank,
horses that wants to shake his head when sweet iron Mullen mouthpiece.
worked and competed on. This bit is a
favorite because it allows riders to help a
sensitive horse in the turn.
9
Printed on: 02/28/14
Bits
1-800-654-8547
GRAZING BIT
RR-4020
PERFORMANCE BIT
RR-4118
Stainless steel “C” bit with 5” shank,
medium port sweet iron mouthpiece.
St ainle s s Ste el all ar ound bit
with 8” shank, sweet iron Mullen
mouthpiece.
PERFORMANCE BIT
RR-4021
PERFORMANCE BIT
RR-4120
Stainless Steel all around bit with
8” shank, medium port sweet iron
mouthpiece.
Stainless steel “C” bit with 5” shank,
medium port copper mouthpiece.
PERFORMANCE BIT
RR-4121
Stainless Steel all around bit with
8” shank, medium port copper
mouthpiece.
COMBINATION
HACKAMORE BIT
RR-4417
Combination hackamore with 1/4”
3-piece twisted dog bone mouth
piece.
COMBINATION
HACKAMORE BIT
RR-47B17
Twisted wire dogbone mouthpiece.
This is a bit for starting barrel training
on horses that have a sensitive mouth
that do not need much control. It is
nice and soft, offering complete rate
and lift for turns.
LIFTER BIT
RR-4708S
LIFTER BIT
RR-4702S
Lifter bit with 3/8” sweet iron snaffle
and 6” shanks.
GAG BIT
RR-4712
Short shank lifter. Good for starting
barrel training on a young horse or a
horse that has a sensitive mouth and
doesn’t need much bit. A nice soft
bit that offers complete rate and lift
in turns. Two piece sweet iron twisted
mouthpiece.
Stainless Steel gag with 7" shank and
chain mouth. Gag action the entire
length of the shank.
10
Printed on: 02/28/14
LIFTER SNAFFLE WITH DOTS
RR-4702D
Gag Bit Smooth Snaffle mouthpiece
was designed for that sensitive or light
mouthed horse. The long shank offers
plenty of whoa while maintaining and
bend required. This is great for a young
horse and a good transition bit from an
O-Ring Snaffle.
GAG BIT
RR-4717D
Gag bit with the 3-piece dog bone
mouthpiece has more direct contact
in the corners of a horse’s mouth
giving you a quicker response.
Bits
KIRBY GAG BIT
RR-4761
CONNIE COMBS GAG BIT
RR-4725
Gag bit develops suppleness.
Gives shoulder lift. Can stabilize
hindquarters. Rib cage lift.
SHORT SHANK LIFTER BIT
RR-4750-S
SHORT SHANK LIFTER BIT
RR-4726S
Short gag bit with 3 piece ported
bradoon. This bit allows for tongue
relief yet gives more pressure to the
outside of the bars. Very effective in
head setting and/or breaking a horse
at the poll. 7” shank, 5” mouth.
“C” BIT
RR-4821
With medium port, this bit will
help those who need plenty of
control. As the rider pulls back,
the tongue is compressed into
the bottom of the mouth, but
still gives the tongue a place to
go. 7” shank, 5” mouth.
ARGENTINE BIT
RR-5009
Stainless Steel training/breaking bit.
5” shank with small twisted Copper
snaffle mouthpiece.
1-800-654-8547
With sawtooth mouthpiece, works
similar to the chain type mouth,
yet has more contour to the horse’s
mouth to touch new nerves and give
more control with a slight gag action.
7” shank, 5” mouth.
3-RING ARGENTINE BIT
RR-4902
An all time classic cheek. Excellent for starting
a colt on curb pressure, tuning a horse or
riding any well bitted horse. This mouthpiece
packs easily, offers medium control yet light
enough to pull a young colt around.
ARGENTINE BIT
RR-5010
ARGENTINE BIT
RR-5002
Stainless Steel training/breaking bit.
5” shank with sweet iron snaffle
mouthpiece.
ARGENTINE BIT
RR-5011
Argentine bit with extra small
twisted stainless steel snaf fle.
BEWARE: Heavy hands will make
this a severe bit. Never tie a horse
in with this bit. 6" shank, 5" mouth.
Stainless Steel training/breaking
bit with 1/4” sweet iron bradoon
5” mouthpiece. 5” shank.
Gag bit with copper mouthpiece,
stainless steel medium port, and 7”
shank. Designed for the well broke
performance horse or tough-mouthed
older horses where the rider needs
more control.
ARGENTINE BIT
RR-5008
Stainless Steel training/breaking bit
with 5” shank. 5” sweet iron twisted
snaffle mouthpiece.
ARGENTINE BIT
RR-5012
Argentine bit with chain mouthpiece.
6" shank, 5" mouth.
11
Printed on: 02/28/14
Bits
1-800-654-8547
ARGENTINE BIT
RR-5017
Argentine bit with 3-piece twisted
dog bone mouth piece.
ARGENTINE BIT
RR-5066A
TRAINING BIT
RR-5018
ARGENTINE BIT
RR-5019
Stainless Steel training/breaking
bit. 5" shank with sweet iron
Mullen mouthpiece.
RING SNAFFLE BIT
RR-508
Light 3” Stainless Steel ring with
small sweet iron twisted 5” snaffle.
COLT BIT
RR-5132
An ideal step up from a ring snaffle
during the training process. It has a
loose shank sidepull with large rein
rings for lighter control. Sweet iron
medium port mouth. 6" shank, 4-3/4"
mouth.
RING SNAFFLE BIT
RR-509
Medium 3” Stainless Steel ring
with twisted copper mouth piece.
COLT BIT
RR-5151
Loose jaw colt bit with 5/8”
Mullen mouth piece.
Argentine bit with 3-piece sweet
steel mouthpiece with copper rings
in center.
RING SNAFFLE BIT
RR-510
Medium 3” Stainless Steel ring
with 1/8” stainless steel twisted
5” snaffle. This mouth piece can be
severe and adds lots of control. Do
not tie a horse with this bit.
RUTLEDGE ROPER
RR-5252
Sweet iron flat iron bar port. This is one
of the most humane bits in our line. This
bit may look severe, but it is not, and it is
very effective. The revolving mouthpiece
stays in place and each cheek works
independently letting the curb chain
apply pressure against the horse's chin.
It is an ideal bit for roping, barrel racing,
or general pleasure riding.
12
Printed on: 02/28/14
Argentine Bit, twisted sweet iron with
smooth ported mouthpiece. Helps to
keep shoulders up while maintaining
lateral movement.
RING SNAFFLE BIT
RR-511
Medium 3” ring snaffle with 1/4” mild
steel Bradoon mouth piece.
COMBINATION
HACKAMORE BIT
RR-5512
Combination hackamore with rope
nose and chain mouth piece.
Bits
SAM JENKINS BIT
RR-5770
Needing more control than a ring
bit? This is an extremely good
shank. Low leverage but adds
some curb pressure for more
control. This mouthpiece has lots
of tongue relief for wide sensitive
tongues. Port height is 2”.
RING SNAFFLE BIT
RR-607
Heavy 3” stainless steel ring with
3/8” sweet iron mouth piece.
SWEET SIX BIT
RR-6012
RING SNAFFLE BIT
RR-605
Small chain mouthpiece with 3”
cheeks and a 5-1/2” mouth. This bit
offers the direct control of a snaffle
with the additional control of curb
pressure. The small chain mouthpiece
adds more “bite” and even more flex
than the snaffle sweet six.
Heavy 3” Stainless Steel ring with
large sweet iron twisted 5” snaffle.
RING SNAFFLE BIT
RR-616
RING SNAFFLE BIT
RR-619
Heavy 3” Stainless Steel ring with a
7/16” sweet iron mouthpiece.
COMBINATION GAG HACKAMORE
RR-6305
9” cheeks and rope nose for tuck and lift.
Reshaped and longer shank for leverage and
control. If you are running competition and
your horse charges hard, this bit is designed
especially for you. Sweet iron large twisted
mouth piece.
Heavy 3” Stainless Steel ring with a
three piece sweet iron mouthpiece
with Copper rollers.
COMBINATION
HACKAMORE BIT
RR-6317
9” cheeks and rope nose for tuck
and lift. Reshaped and longer shank
for leverage and control. If you are
running competition and your horse
charges hard, this bit is designed
especially for you.
COMBINATION GAG
HACKAMORE
RR-6405
1-800-654-8547
RING SNAFFLE BIT
RR-606
Heavy 3” Stainless Steel ring with
double twisted Copper and sweet
iron mouthpiece.
RING SNAFFLE BIT
RR-628
Heavy 3” Stainless Steel ring
with a three piece sweet iron
mouthpiece.
STRIVERS HACKAMORE BIT
RR-6500
Adjustable hackamore with rope nose,
7” shank. Tired of the pinching, blocking,
and cocking of a standard hackamore?
With twisted sweet iron snaffle and As you go to one rein, the opposite cheek
will collapse against the head, helping
leather covered nose. 8" shank.
to make this a turning tool to bend a
colt’s head. It will also help correct an
old horse’s problem. This bit should be
ridden with a light hand, as this can be
a strong stopping bit.
13
Printed on: 02/28/14
Bits
1-800-654-8547
STRIVERS SHORT SHANK
HACKAMORE
RR-6600
7” Shank
The unique design of this hackamore
allows each cheek to move freely and
independly without pinching or binding.
Medium leverage shank combined with
a chain nose that gives some bite to the
bridge of the horse’s nose. Retains good
control and has plenty of flex.
JARRET GAG BIT
RR-7661
3/8” copper ported Mullen mouth.
This is a very smooth action gag
cheek designed not to pinch. The
6-1/2” cheek gives it good control.
The headstall ring with curb helps
to stabilize the cheek and balance
the bit. The Mullen relief helps this
mouthpiece pack well. The port
adds some tongue relief and the
3/8” diameter adds enough bite for
surprising control with this bit.
GAG BIT
RR-8008
This gag bit with a small twisted
mouthpiece is designed to be ridden
with the ring up to lock the headstall to
help stabilize the bit or can be flipped
over to lock the reins for a quicker
response. This mouthpiece adds a lot
of “bite” for schooling a horse.
JARRETT GAG BIT
RR-7617
STRIVERS LONG SHANK
HACKAMORE
RR-6600-9
9” Shank
The unique design of this hackamore allows
each cheek to move freely and independly
without pinching or binding. Medium
leverage shank combined with a chain
nose that gives some bite to the bridge of
the horse’s nose. Retains good control and
has plenty of flex.
Nice all-around combination of
shank and mouthpiece. A well
balanced bit excellent for roping
horses that need whoa! This
mouthpiece has lots of tongue
relief for wide sensitive tongues.
Port height is 2”.
BARREL BIT
RR-7666
Jarrett gag bit with 1/4” sweet ported
bradoon and 6-1/2” cheeks. This is a very
smooth action gag cheek designed not to
pinch and gives good control. The headstall
ring with curb helps to stabilize cheek and
balance the bit. The relief helps this mouth
piece pack well. The port adds some tongue
relief. The 1/4” diameter adds enough bite
for surprising control with this bit.
GAG BIT
RR-8012
This gag bit with a chain mouthpiece
is designed for horses that are heavy
or lug on the bit. It can be turned
either way in the horse’s mouth for
the severity you need. Divided ring
provides quicker response. Can be an
effective training bit.
14
Printed on: 02/28/14
HIGH PORT ROPER BIT
RR-6770
Jarrett gag bit with small twisted mouth
piece. The dog bone adds “bite” to this
bit to better control horses that need
more “rate”. The 6-1/2” cheek gives it
good control. The headstall ring with
curb helps stabilize the cheek and
balance the bit.
LIFTER BIT
RR-7727C
LIFTER BIT
RR-7711
Lifter bit with copper covered sweet
iron mouth. This combination of
tastes makes for a wet and soft
mouth for better feel.
Lifter bit with bradoon mouth
piece.
GAG BIT
RR-8017
Gag bit with twisted 3-piece dog
bone mouth piece.
GAL LEG REINER BIT
RR-8112
Gal leg reiner bit with 5” chain
mouth piece and 8” cheeks.
Bits
GAL LEG BIT
RR-81S12
This bit features 8” cheeks, 5” mouth
and a large chain mouth. The stainless
steel cheek was designed with excellent
balance and the leverage needed for
competition. The chain mouthpiece
conforms to the horse’s mouth, it is
excellent for horses that are high headed
when bit pressure is applied. Helps to
break a horse at the poll to get the nose
in and head down. When in competition,
this bit will help lift the shoulders and
lower the hind end for stronger turns and
powerful stops.
Stop-N-Turn with stainless steel
4-1/2” shank rigid curb that adds
plenty of whoa. With the swivel shanks
it adds flex and the combination steel
curb and rope pressure will put the
turn in the horse.
Stop-N-Turn with 4-1/2” shank rigid
curb that adds plenty of whoa. With
the swivel shanks it adds flex and
the combination steel curb and
rope pressure will put the turn in
the horse.
CHRISTY GAG BIT
RR-8702
GRADUATION SNAFFLE BIT
RR-8617
QUICK STOP
RR-8400
QUICK STOP
RR-8300
Smooth 3/8” Sweet Iron mouth and
3” cheeks. Excellent draw gag that
has more mouthpiece action than
the half circle gag. Combined with
a smooth sweet iron snaffle for good
headset and flex at the poll. Not as
severe as the three piece mouthpiece
for better lift in the front.
1-800-654-8547
COMBINATION HACKAMORE
RR-8517
Combination hackamore with adjustable
chain nose, 3-piece dogbone mouthpiece
and 8” cheeks. There are two ways to
stop a horse, pain or control. When you
use pain, very soon your horse will stop
turning in anticipation of the pain you are
going to inflict on him at the end of the
run. This nose shape spreads the contact
across the full face of the horse. In most
cases you can let your tie down out so
your horse can run better yet still rate
and collect your horse. Roping horses
will stop much better on their rear end.
CHRISTY GAG BIT
RR-8708
Twisted 3/8” Sweet Iron mouth and
2-1/2” cheeks. Excellent draw gag that
has more mouthpiece action than the
half circle gag. This mouth piece packs
well. It is small enough to have some
bite for control but can be ridden for
competition.
CHRISTY GAG BIT
RR-8712
Graduation snaffle with 3-piece dogbone mouthpiece.
The design of this bit is enhanced by the solid
purchase above the cheek. This bit is for the broken
horse that requires a smooth light feel in the mouth.
As the horse graduates into a finished open barrel
racing or speed event the reins can be dropped into
the rein stop and a curb added for control. Headstall
attaches to small ring above purchase.
Small chain 5” mouth and 2-1/2” cheeks.
E xc ellent dr aw gag that has mor e
mouthpiece action than the half circle gag.
The chain mouth has become very popular
with riders. The chain conforms well
with the mouth and applies slight tongue
pressure for good headset and control.
SHAY LEE CHAIN HACKAMORE
RR-9000H
CHRISTY GAG BIT
RR-8717
3/8” twisted sweet iron dogbone mouth and
3” cheeks. Excellent draw gag that has more
mouthpiece action than a half circle gag.
The twisted mouthpiece adds a little bite for
more control and the three piece dogbone
adds some tongue pressure for better rate
and increases bar pressure for better control.
JARRETT’S DRAW
SHANKS
RR-9000
9” draw shanks allow you
to add the mouth piece of
the draw bit you want. Made
of stainless steel, the top
rings unscrew to easily allow
changing of draw bits.
Adjustable chain nose band barrel bit. There are
two ways to stop a horse, pain or control. When
you use pain, very soon your horse will stop
turning in anticipation of the pain you are going
to inflict on him at the end of the run. This nose
shape spreads the contact across the full face
of the horse. In most cases you can let your tie
down out so your horse can run better yet still
rate and collect your horse. Barrel horses will
stop much better on their rear end.
GAG BIT
RR-9117
W it h t wis t e d t hr e e pie c e
dogbone mouthpiece.
15
Printed on: 02/28/14
Bits
1-800-654-8547
CHAIN NOSE
HACKAMORE BIT
RR-9200
RING COMBINATION ROPE
NOSE HACKAMORE
RR-911S
Training snaffle with 5” sweet iron
bradoon and rope nose. Works well on
colts that try to get heavy on a regular
snaffle. Gives a hackamore feel and
action, while being mild in the mouth
and adds a side pull effect from the
rope noseband. 3” rings.
COMBINATION GAG BIT
RR-9817
Rope nose hackamore with twisted
dog bone mouthpiece. A nice medium
control hackamore for advanced
training when a young horse begins
picking up speed and needs a little
bit more rate than with the ring bit.
Good for competition horses with
natural rate.
HEAVY RING SNAFFLE BIT
RR-917
Heavyweight Stainless Steel 3” rings with
three piece small twisted snaffle and rope
nose. The heavier ring with a longer shank
gives more control with easier touch. The three
piece snaffle gives more feel to the mouth.
POWER CURB
RR-9990
A creative alternative to the
chain or leather curb for
additional control. The power
curb offers a firm feel even to
short shanked bits.
SEVEN SHANK BIT
RR-S1920
There are two ways to stop a
horse, pain or control. When you use pain, very soon
your horse will stop turning in anticipation of the pain
you are going to inflict on him at the end of the run.
This chain nose spreads the contact across the full
face of the horse. In most cases you can let your tie
down out so your horse can run better yet still rate
and collect your horse. Roping horses will stop much
better on their rear end.
Loose cheek pleasure horse bit with 1/2”
medium port sweet iron mouthpiece
and 7” trail riders cheeks. This cheek
is designed for effective communication
and comfort for horses that spend hours
under the saddle. The loose shank adds
some flex. This bit’s features are: low
leverage, swept back shanks (no lipping)
and short purchase for quick release. This
mouthpiece packs well and places less
pressure on the bars.
RUBBER BIT GUARD
MT-24419
SEVEN SHANK BIT
RR-S1935
Loose cheek pleasure horse bit with
square high port sweet iron mouthpiece.
This cheek is designed for effective
communication and comfort for horses
that spend hours under the saddle. The
loose shank adds some flex. This bit’s
features are: low leverage, swept back
shanks (no lipping) and short purchase
for quick release.
NEOPRENE BIT GUARD
WITH VELCRO CLOSURE
MT-24419-5
3-1/2” diameter, Pair.
2-3/4” diameter, pair. Available in red,
blue or black.
16
Printed on: 02/28/14
Bits
DEXTER RING BIT
MT-21240
BIT
MT-21240-1R
Stainless steel 5” half cheek Dexter
ring bit with no prongs.
LIL’ “S” SIDEPULL
MT-21208-2
Stainless steel, half cheek Dexter
Ring Bit with prongs. 5” rubber
mouth.
6” stainless steel “S” shank with rope
noseband and chain curb. This is a nice
starter bit. Not a lot of “whoa” but excellent
for flex and collection.
BIT
MT-21310
1-800-654-8547
DEXTER RING BIT
MT-21240-R
Stainless steel, half cheek, 5”
rubber mouth Dexter ring bit.
BIT
MT-21518
Stainless steel screw bit. Stemins/Spicer.
Full cheek snaffle bit. Stainless
steel with 5” copper mouth,
6-1/2” cheeks.
BIT, FUTURITY “THE
SHORTY”
MT-23001-1
Sweet iron brushed low hinged port
mouthpiece with flush center copper
roller, copper inlays and 5” cheeks.
BIT, PORTED CHAIN
MT-23020
Sweet Iron por ted chain
mouthpiece, 5-1/2” cheeks with
stainless steel floral trims. This bit
helps to keep shoulders up while
maintaining lateral movement.
BIT
MT-23620
Antique horseshoe low articulated
correction bit. 5-1/8” low port
mouth with copper roller, 7-1/2”
shanks with horseshoe and floral
design.
BIT
MT-23701
Antique finish with 5" sweet iron
3-piece dogbone mouth with copper
wrapped links. 7" cheeks with star
cutout concho, stars and dots.
FLORAL CONCHO WESTERN DEE BIT
MT-23040-4
BIT, ANTIQUE FLORAL
MT-23001-3
Sweet iron 3-piece mouth with
copper inlays and 7” cheeks with
floral trims.
Antique finish D-rings with floral trim and concho.
5-1/8” sweet iron curved snaffle mouth piece with
copper inlays. Level two.
ANTIQUE 66 TWISTED DOG
BONE GAG BIT
MT-23813
5-1/8” sweet iron twisted dog bone
curved mouthpiece and 5” cheeks
with gag effect.
BIT, EGGBUT SNAFFLE
MT-23060-1
Sweet iron 3-piece mouth
with copper inlays and center
copper roller, eggbutt flat and
round cheeks.
ANTIQUE BARB WIRE
SNAFFLE DEE BIT
MT-23820-5
5 -1 / 8 ” s w e e t ir o n c u r v e d
mouthpiece with copper inlays,
stainless steel barb wire and
engraved trim.
17
Printed on: 02/28/14
Bits
1-800-654-8547
BLACK SATIN FLAT
CALVARY BIT
MT-23830
5-1/8” articulated hinged port curved
mouthpiece with copper inlays. 8-1/4”
flat calvary cheeks with floral, stars
and dots trim.
STAINLESS STEEL JUNIOR
COW HORSE ROLLER DOG
BONE GAG BIT
MT-23831-8
5 -1 / 8 ” s w e e t i r o n l o w p o r t
m o u thpie c e, 7 ” ch e e k s with
stainless steel dots. The mouthpiece
is attached at the bottom of the
barrel creating a higher purchase
and more action at the poll.
5-1/2” sweet iron smooth snaffle curved
mouthpiece, 7/16” gauge. 6” cheeks
with gag effect. A good schooling bit for
young horses.
5-1/8” sweet iron smooth snaffle dog
bone mouthpiece with copper inlays.
5-1/2” short shank with gag effect and
floral decorations.
GAG BIT
MT-23901-8
5” x 3/8” sweet iron smooth dog bone
snaffle with copper roller. 5-1/2”
cheeks with gag effect. The copper
roller keeps the horse relaxed while
the gag effect helps you collect the
horse. Good for young to intermediate
horses (moderate effect).
BIT, LOW RIDER
MT-23907-9
JUNIOR COWHORSE SMOOTH
SNAFFLE GAG BIT
MT-23831
BLACK SATIN SHORT GAG
BIT
MT-23830-5
Antique Margarita concho gag bit
with 5-1/8” copper twisted dog bone
mouthpiece. 5-1/4” cheeks with
Margarita concho and gag effect.
For young to intermediate horse
(moderate effect).
S t ainle s s s t e el 5” ch e e k s
fully engraved for young to
intermediate hor se. 5 -1/8”
3 -piece sweet iron snaf fle
mouthpiece with copper inlays
and sweet iron wrapped link.
BLACK SATIN DOG BONE BIT
MT-23908-2
BLACK SATIN BIG DIAMOND
BIT
MT-23908-1
5 -1 /4” Swe e t Ir o n 3 - p ie c e d o g
bone mouthpiece entirely copper
wrapped. 6-3/4” cheeks with medium
gag effect. Stainless steel trims and
dots. The copper wrapping produces
extra salivation and relaxation. For
Intermediate Horse. (Moderate effect).
5-1/4” sweet iron curved low port
with copper inlays. 5-1/4” cheeks
with big diamond trim and dots. For
intermediate horse. (Moderate effect).
18
Printed on: 02/28/14
ARGENTINE SHOW BIT
MT-23904
STAINLESS STEEL COPPER
ROLLER DOG MEDIUM PORT
C BIT
MT-23831-7
5” x 1/2” sweet iron medium port
mouthpiece with copper roller and
5-3/4” cheeks. The copper roller
adds some tongue pressure for better
control. Good for advanced horses
(moderate to strong effect).
ANTIQUE LOW HINGED PORT
BIT
MT-23907-8
Sweet iron curved mouthpiece with flush
copper barrel hinge. 7-1/2” cheeks with
little gag effect. Stainless steel dots. The
mouthpiece is attached at bottom of the
tubing creating a higher purchase and
more action at the poll. For intermediate
horses. (Moderate effect )
MINI BIT WITH COPPER
SNAFFLE
MT-24066-2
Stainless steel mini horse training
bit with 3-1/2” copper snaf fle
mouthpiece, 5” cheeks.
Bits
BIT
MT-24069-9
Three piece mouth with copper
rollers, stainless steel with 7”
cheeks.
1-800-654-8547
BIT
MT-2473
BIT
“STAR CORRECTION”
MT-24075
Anti-lugging bit. Stainless steel,
5” with control bar under chin.
Antique 8" "S" shank with diamond
and dots, 5-1/2" sweet iron big links
chain mouth, flat curb chain and PP
connector.
Antique with engraved German
Silver stars and dots. 5” Stainless
smooth correctional por t with
copper barrels. 8” shank.
BIT
MT-25000-3
Antique 7" shank with rope,
diamond and dots trim. 5-1/8"
sweet iron por ted chain
mouthpiece with rubber keepers.
Flat curb chain and PP connector.
PONY HACKAMORE
MT-25108
Stainless Steel, 7-1/2" cheeks,
Pony size.
COMBINATION
HACKAMORE
MT-25156-2
Stainless Steel, 5" copper snaffle
mouth, 7-1/4" cheeks.
BIT
MT-25000-2
HACKAMORE
MT-25100-1
Stainless Steel, clear plastic covered
bike chain noseband, 10" cheeks.
HACKAMORE
MT-25100
STOP & TURN
MT-25107-3
Stainless Steel with rope nose, 5"
cheeks.
Stainless Steel with gum rubber
covered bike chain noseband. 8-1/2"
cheeks, Horse size.
HACKAMORE
MT-25111
HACKAMORE
MT-25110-8
Stainless Steel. Braided leather
nose. 9" cheeks.
Chrome plated, braided leather
nose. 9" cheeks.
PONY CURB BIT
MT-25209
CURB BIT
MT-25208
Nickel Plated Bit with 7-3/8 "
Cheeks, 5" Mouth.
Nickel plated Pony bit, 4" medium
port mouth, 6-5/8" cheeks.
HACKAMORE
MT-25113
Chr ome plate d. D ouble d and
stitched leather noseband. 9 "
Cheeks
BIT
MT-25211
Nickel plated, 6" cheeks, 5" mouth.
19
Printed on: 02/28/14
Bits
1-800-654-8547
RING SNAFFLE
MT-25224
BIT
MT-25220
H a n d - b u f f e d, N i c k e l p l a t e d
malleable Iron, 9" cheeks, 5-1/8"
mouth.
RING SNAFFLE
MT-25228-1
5" Malleable Iron Snaffle Bit, 2-1/4"
Ring.
BIT
MT-25278
Black steel correction bit, brass inlay.
8" cheeks. 5" mouth.
BIT
MT-25290
Black Steel, 5" high port mouth
with Copper wire wrap, 9" cheeks.
Nickel plated, 4-1/2" snaffle mouth,
pony bit, 1-3/4" rings.
BIT
MT-25221
Nickel plated, 5-1/4" mouth, 2-1/4"
rings.
Nickel Plated, 6" cheeks, 4-1/2"
mouth.
BIT
MT-25251
RING SNAFFLE
MT-25228-2
Stainless Steel Sweet Iron Twisted
Wire Snaffle, 3" Dees.
Black Steel, 5" snaffle mouth, 3"
rings.
LIFE SAVER BIT
MT-25277-1
Shank snaffle black steel lifesaver
bit, 5” copper wire wrap mouth,
6” cheek.
BIT
MT-25280
BIT
MT-25279
Black Steel bit with 6-1/2" plain
cheeks, 5" mouth, medium port.
Black Steel, 5" snaffle mouth, 6"
cheeks.
BIT
MT-25294
CORRECTION BIT
MT-25293
Black Steel 5" 3-piece snaffle mouth.
6" cheek.
Black Ste el, 5" C opp er wire
wrapped correction bit.
6" cheeks.
20
Printed on: 02/28/14
RING SNAFFLE
MT-25228
BIT
MT-25285
Black Ste el, 5" C opp er wir e
wrapped snaffle mouth, 6" cheeks.
CORRECTION BIT
MT-25296
Black Steel, 5" correction bit with
Copper rollers. 8" cheeks.
Bits
BIT
MT-25313
Chrome plated, 6-1/2" Cheeks, 5"
Copper Mouth.
BIT
MT-25353
Chrome plated 5" medium port
mouth, 6-1/2" cheeks.
BIT
MT-25512
Stainless Steel, 5" mouth, 6-1/2"
cheeks.
FULL CHEEK SNAFFLE
MT-25516
Stainless Steel, 5" mouth.
1-800-654-8547
DEE BIT
MT-25344
RING SNAFFLE
MT-25314
Chrome plated 5-1/4" mouth.
3-1/8" dees.
Chrome plated mule bit, 6-1/2"
chainsaw mouth, 2-1/2" rings.
BIT
MT-25432
BIT
MT-25385
Black Steel 5" Snaffle Mouth with
Copper Inlay, Stainless Steel/Black
Steel 6-1/2" Loose Cheeks.
Chrome plated malleable iron, 6"
cheeks, 5" Copper mouth.
BIT
MT-25512-5
5" Stainless Steel and Copper roller
mouth, 6-1/2" cheeks. Stainless
Steel.
BIT
MT-25511
Stainless Steel 5" mouth,
6" cheeks.
BIT
MT-25526-1
BIT
MT-25526
Stainless Steel 5" Argentine mouth,
6" cheeks.
Stainless Steel 5" Copper snaffle
mouth, 6" cheeks.
DEE BIT
MT-25345
Chrome plated 5" rubber covered
mouth, 2-7/8" dee.
BIT
MT-25510-6
Performer stainless steel brushed
medium transition bit, 5” mouth with
3-piece copper wire wrapped link,
6-3/4” cheeks.
BIT
MT-25513
Stainless Steel, 5" Copper mouth,
6-1/2" cheeks.
EGGBUTT SNAFFLE
MT-25534
Stainless steel, 5" snaffle mouth,
2-3/4" rings.
21
Printed on: 02/28/14
Bits
1-800-654-8547
DEE BIT
MT-25544
BIT
MT-25544-7
Stainless Steel 5” mouth,
2-7/8” dee.
Stainless Steel racing Dee, 5" rubber
mouth snaffle, 2-7/8" Dees.
DEE BIT
MT-25545
Stainless steel 5” mouth,
3” dee.
BIT
MT-25539
Stainless Steel 5" snaffle mouth with
Copper roller. 8-1/2" cheeks.
BIT
MT-25551-1
DEE BIT
MT-25545-1
Stainle s s Steel, 5” rubber
covered mouth, 2-7/8” dee.
BIT
MT-25551-2
Stainless steel 5" single twisted
copper wire mouth, 3" flat rings.
BIT
MT-25545-6
Stainless Steel, 5" triangular shaped
snaffle mouth, 3" rings.
Stainless Steel, 5" three piece
mouth with tongue depressor,
2-1/2" rings.
RING SNAFFLE
MT-25551-5
RING SNAFFLE
MT-25551-7
Stainless Steel, 5” Sweet Iron
curved snaffle mouth, 3” rings.
Stainless Steel, 5” Copper snaffle
mouth, 3” rings.
DEE BIT
MT-25554
RING SNAFFLE
MT-25551-9
Stainless Steel ring snaffle, 3" ring,
5" sweet iron mouth.
BIT
MT-25550-9
BIT
MT-25552-5
Stainless Steel 5" Copper wire
wrapped mouth. 2-1/2" dees.
Stainless Steel, 5-1/4" Sweet Iron
chain mouth, 7" cheeks.
22
Printed on: 02/28/14
Stainless steel ring snaffle, 5”
offset double twisted copper wire
mouth, 3” beveled flat rings.
RING SNAFFLE
MT-25551-8
Stainless Steel, 5" small twisted
wire sweet iron mouth, 3" rings.
DEE BIT
MT-25555
Stainless Steel, 5" Stainless Steel
and Copper roller mouth, 2-1/2"
dees.
Bits
DEE BIT
MT-25567
Stainless Steel, 5" Copper mouth,
2-7/8" dees.
RING SNAFFLE
MT-25574-5
BIT
MT-25576
Stainless Steel, 5" sweet iron
twisted wire snaffle mouth. 7-1/2"
cheeks.
Stainless steel, 5" sweet iron snaffle
mouth, 7-1/2" Wonder Gag cheeks.
BIT
MT-25580-3
CORRECTION BIT
MT-25583-4
BIT
MT-25681
Stainless Steel, 5" 3-piece snaffle
mouth with sliding Copper roller,
6" cheeks.
Stainless Steel, 5" sweet iron mouth.
3" beveled rings.
Black Steel, 5" snaffle mouth with
Copper inlay. 3" rings.
BIT
MT-25575-9
Stainless Steel, 5" medium port
Copper Mouth, 6" Cheeks.
RING SNAFFLE
MT-25574-6
1-800-654-8547
DEXTER RING BIT
MT-25575-5
Stainless Steel, 4-3/4" Dexter
ring bit.
BIT
MT-25576-6
Stainless Steel 5" Copper twisted
wire snaffle mouth, 7" cheeks.
CORRECTION BIT
MT-25583-5
Stainless Steel correction bit with
5" Copper/Stainless Steel mouth,
6" cheeks.
Stainless Steel correction bit with
5" Copper/Stainless Steel mouth.
7-1/4" cheeks.
BIT
MT-25689
BIT
MT-25684
Stainless Steel, 5" 3-piece snaffle
mouth with sliding Copper roller.
6-3/4" cheeks.
Stainless Steel 5" swivel port
mouth with roller, 6-1/2" cheeks.
23
BIT
MT-25580
Stainless Steel Bit with 5" Mouth,
7" Flat Cheek with Design.
BIT
MT-25585
Stainless Steel with 6" cheeks, 5"
Copper mouth.
BIT
MT-25732-1
Brushed stainless steel correction bit,
5” mouth with copper barrels, 8-1/4”
S-shank with silver trim and dots.
Printed on: 02/28/14
Bits
1-800-654-8547
ALUMINUM MEDIUM PORT
CURVED BIT
MT-25732-2
5" Sweet Iron mouth, copper inlay,
8-3/4" engraved aluminum cheeks.
ANTIQUE LOW PORT
HINGED FUTURITY BIT
MT-25760-4
BIT, ALUMINUM
MT-25732-5
Precision spring system, 5" high port
mouth, 8-1/4" aluminum engraved
cheeks with conchos.
5" Sweet Iron curved and ported
mouthpiece, copper inlays, SS
brushed barrels, 5-1/2" antique
short shanks with 3 SS dots.
ALUMINUM SNAFFLE BIT
MT-26113
Aluminum, 5" sweet iron snaffle mouth
with copper inlay, 8" loose cheek.
GAG SNAFFLE
WITH HEADSTALL
MT-26600
Black steel, 5" sweet
iron snaffle sliding gag,
on headstall.
BIT
MT-26310-4
Black satin “C” bit with spots. 5”
polished steel low port mouth.
6-1/2” cheeks.
BIT
MT-26310-5
Black satin bit with copper roller,
polished steel mouthpiece.
5" mouth, 7" cheeks.
ADJUSTA TRAINING BIT
MT-26421
Mouthpiece adjusts from 4-1/2” to
5-1/2”, stainless steel copper roller,
8” cheeks.
GAG SNAFFLE
WITH HEADSTALL
MT-26601
Black steel, 5" twisted
wire snaffle sliding gag,
on headstall.
BIT
MT-26623
Rubber mouth dee with adjustable
mouthpiece from 4-3/8” to 5-1/4”,
stainless steel.
ANTIQUE WESTERN DEE
BIT
MT-26811
Antique Western Dee bit. 5" copper
inlay snaf fle mouth. Engraved
German Silver trim.
CORRECTION BIT
MT-26876-5
Antique bit with 5-1/4" snaffle
mouth, Ranger Star concho.
BIT
MT-27006
Antique low articulated correction bit
with 5" low port mouth with copper
roller. 8" "S" shanks with flat stainless
steel trim and dots.
Warner type hackamore, rope nose.
Nose swivels for better flex plus it
floats when you pull the shanks,
but will not drop down.
24
Printed on: 02/28/14
ANTIQUE WESTERN DEE
BIT
MT-26875
Bits
1-800-654-8547
BIT
MT-27015
Black steel 5" cheek gag bit, copper
wire wrapped mouth.
“GUNSMOKE COLLECTION”
CORRECTION BIT
MT-27100-6
BLACK SATIN HINGED PORT
BIT
MT-27010-4
“Gunsmoke Collection” correction bit with dots. 7
¾” shanks. Polished steel mouth with copper inlay.
5” hinged port mouth with copper roller
and copper inlays. 8” S-shank with dots.
BIT
MT-27113
Antique chain bit, 5” mouth with big
linked chain and rubber keepers, 8”
cheeks with floral pattern, engraved
silver and dots.
HACKAMORE
MT-27101-7
German silver hackamore, braided
rawhide covered noseband, 8-1/2"
engraved silver trim on flat cheeks.
SANTA FE ARGENTINE BIT
MT-28710-1
THE “ARGENTINE”
MT-27200-3
Antique with stainless steel dots. 5” sweet
iron 3-pieces broken mouthpiece with 4
copper rings and inlays. 5-1/2” shank with
“Swivel Free System”. A very good bit for
introducing green horses to leverage. The
broken mouth allows tongue relief.
PONY PISTOLS CURB BIT
MT-28710
Antique finish with stainless steel
engraved trim and pistol motif.
4-1/8” sweet iron low port curved
mouth piece and 4-1/2” cheeks.
Level three.
Antique finish with stainless steel
engraved trim. 5-1/8” sweet iron
square por t mouth piece with
copper inlays and 5” swivel cheeks.
Level three.
SANTA FE CONCHO
LOOSE RING BIT
MT-28710-4
HIGH PORT BIT
MT-28710-2
Antique finish with stainless steel
engraved trim. 5-1/8” sweet iron high
port mouth piece with copper inlays and
6” medium shank cheeks. Level four.
Antique finish with rosetta concho
and stainless steel inlays. 5-1/8”
sweet iron curved snaffle mouth
piece with copper inlays. Level two.
SANTA FE BONANZA
MT-28710-7
Antique finish with engraved trims in
floral motif. 5-1/8” sweet iron curved
snaffle mouth piece with copper inlays.
5-1/4” short shank cheeks. Level two.
SANTA FE PONY
CORRECTIONAL
MT-28711-7
SANTA FE FLORAL
CROSS CONCHO BIT
MT-28710-9
Antique finish 6” cheeks with
cross concho, floral trims
and rope edge. 5-1/8” sweet
iron curved mouth piece with
floating spade and copper
rings. Level two.
Antique finish with stainless steel and copper
trims. 4-1/2” correctional mouth piece with
1-1/2” port and copper rollers. 6” short shank
cheeks. Level three.
25
Printed on: 02/28/14
Spurs
1-800-654-8547
TO SPUR OR NOT TO SPUR
CHOOSING THE RIGHT SPUR:
FUNCTION OF THE SPUR
Contrary to popular belief, spurs are not designed to make a horse go fast. Spurs are intended for delivering point-contact
pressure to a horse’s midsection. This allows the rider to guide a horse from side to side and to enhance flexure that a horse
naturally exhibits through its ribcage and along its profile. If you want excellent lateral motion, lightness on the front quarters,
spin and great rollbacks, spurs can be a tremendous aid. If you simply want your horse to go faster, spurs are not the solution.
We recommend that you do not use spurs until your trainer suggests their use, or until you develop sufficient leg control, so you
will not accidentally bump the horse.
THE SPUR
SHANKS - The spur’s shank ranges in length from 1/4” to 2-3/4”. The length of shank is a main factor when choosing a spur; its
length depends on your level of skill and riding style.
ROWELS - Rowels come in all sizes, with a variety of points. The number of points doesn’t change the effect of the spur as much
as whether the points are smooth, blunt or harp. Smooth and blunt are less likely to hurt your horse, and therefore, usually the
best choice for horsemen. Remember, soft point pressure is the object.
BANDS - The spur band fits on the heel of the boot. Band choice is a
matter of personal preference.
JINGLE BOBS - These imitate the old vaquero jingle-noise. These are for
decoration and sound only.
CHAP GUARDS - The guards prevent chaps from becoming tangled in
the rowel.
BUTTONS - This is where the spur straps attach.
HOW TO WEAR SPURS
The spur is worn on the heel of the boot with the sides level (not angling up or down). The curve of the shank should
point down. On western boots, the spur rests above the heel of the boot; on English boots, the spur rests above the spur stop or
along the upper stitching. Spur straps are buckled to the outside, and the straps should be tucked in or cut off.
CHOOSING A SPUR
The less-experienced rider should start with a short shank (1-1/2”) and smooth, blunt rowels. This combination will require
conscious effort on the rider’s part to make sure that the spur only makes contact when the rider wants it. This eliminates the
chance of raking the horse with the spur by mistake. More experienced riders, with an awareness of where their feet are, may
move to a longer shank (2”) with a 10 point rowel. The effort required for contact is much less than with a short shank, and the
range of pressure is expanded. The key factor is in the movement of the rib cage. A longer shank will permit the rider to guide
the horse’s midsection at a variety of gaits, with a minimum of leg pressure.
For high-performance requirements, such as cutting or working cowhorses, you may want a slightly larger rowel, permitting
a rolling motion along the ribcage. Remember, a slight rolling motion of the rider’s foot will deliver all the pressure necessary,
provided the rowel and shank are the appropriate size.
If you ride English, soft point contact is the key. The benefits of soft contact are many, as the horse will begin to focus
more on the job in front of him, instead of worrying about the sharp metal attached to the rider.
Western pleasure riders may want to try a spur with fancy trim and a larger rowel. Since show spurs are mainly for
appearance, the addition of silver trim and long points on the rowels will enhance the appearance of the rider. Note that large
rowels can be cumbersome and get in the way. Your horse will be quick to remind you if you forget where your feet are!
Finally, if you are into rough stock, you will probably want a long shank (2”+) with a five point notched rowel. Bulls have
tougher hides than horses, so the rider can be a little less concerned about where they spur. The emphasis here is on being able
to rake the animal’s shoulder in a visible manner so the judges can get a good look. If you’re riding bucking horses, the long shank
is still a necessity, but you may back off to a 5 point flat-end rowel, given that your mount is already airborne.
We feel the key is to find the spur that provides the best possible result with the least amount of pressure. You may have
to start with something the horse definitely feels, but don’t be afraid to back off once he gets the idea. You’ll find that your horse
will begin to anticipate point contact at particular maneuvers, so as you and the horse progress, you might be able to graduate
to a much gentler and smaller spur. The objective is to help your horse achieve what you want as a rider, through lots of practice
and patience. The spur should be used sparingly and only when needed.
Spurs look and feel great when you have them on, but the best part about spurs is knowing when to leave them off. We
believe that spurs do not have to be big and sharp to get the best performance out of your horse. Rather, they simply have to be
sized to get the job done, and most importantly, worn and used correctly by the rider.
26
Printed on: 02/28/14
Spurs
YOUTH SHOW SPUR
MT-23011-3
YOUTH DOTS SPUR
MT-23011
5/8” band with antique finish with
engraved stainless steel trims. 1-5/8”
shank with chap guard and 12-point
7/8” rowel. Level two.
3/4” band with antique finish, 1-1/2”
shank with 10-point 7/8” rowel.
Level two.
SPUR, FLORAL
BUMPER
MT-23030-4
O val cup, 3 /4” band with
stainless steel floral trims,
stainless steel attachment with
rowels and buttons.
SPUR, STAR TRIM
MT-23030-6
1” band with stainless steel hand
engraved trims and star cut out, 2” shank
with trims, 1-3/16” 16-point rowels.
SPUR
MT-23612-5
Men’s black satin floral engraved with
cross concho spurs. 1-1/2” band and
2-1/2” shank. 8 point rowel.
1-800-654-8547
ROPE EDGE SPUR
MT-23012-3
Antique finish 1” band with
stainless steel rope edge trims and
1-1/2” shank with 8-point blunted
1” rowel. Level two.
SPUR, BLACK SATIN
MT-23050-1
1” band with stainless steel
hand engraved trims and stars,
2-1/4” stainless steel shank,
16-point 7/8” rowels.
BLACK SATIN SPUR
MT-23615-5
SPUR, STAR CONCHO
FLORAL
MT-23030-3
Oval cup, 1” band with stainless
steel floral trims and star concho,
2” shank, 1-1/4” 9-point rowels.
SPUR, BLACK SATIN
MT-23050-3
3/4” band with stainless steel cross
and floral trims, 1-3/4” shank with
chap guard, 3/4” 12-point rowels.
ANTIQUE LADIES SPUR
WITH RHINESTONES
MT-23780-4
Clear
MT-23780-5
Pink
MT-23780-6
Blue
Silver arrows trim, 3/4" band, 1-1/2"
shank with chap guard, 1-1/16" 8-point
rowel.
Antique C omanchero spur s with
rhinestones. 1/2” band, 1-1/4” shank,
7/8” 10-point rowel
ANTIQUE BROWN
LONHORN SPUR
MT-23843-5
O v a l c u p, 3 /4” b a n d w i t h
full stainless steel trim, hand
engraved. 1-1/2” shank with chap
guard, 10-point rowel.
DIAMONDS AND DOTS
SPUR, LADIES’
MT-23845-5
Antique finish 3/4” band with stainless
steel trim and clear rhinestone
accents. 1-1/2” shank with 10-point
7/8” rowel. Level two.
POKER CARDS SPUR
MT-23903
Antique finish with stainless steel
poker cards motif trim. 1” band width
with oval cup and 2” gooseneck
shank with 9-point 1-1/4” rowel.
27
Printed on: 02/28/14
Spurs
1-800-654-8547
DIAMOND FLORAL SPUR
MT-23903-4
Antique finish with stainless steel
diamond floral trim and dots. 3/4”
band width with oval cup and 1-1/2”
shank with 10-point 7/8” rowel.
SHOW SPUR WITH CHAP
GUARD
MT-23908-7
1” band with stainless steel
engraved trims, 2” shank with
chap guard, 1” 8-point rowel.
(Moderate effect)
SHOW SPUR, ROPING
MOTIF, OFFSET
MT-25020-4
Antique offset roping motif show spurs.
1” band with full trim motif, diamonds
and dots. 1-1/2” offset shank with
8-point rowel. Oval and flared out cup
for comfortable fit.
SPUR
MT-23903-5
3/4” black band with three stainless
steel crosses, 1-1/2” low shank with
stainless steel trim. 1” 8-point rowel.
Stainless Steel roping spur, German
Silver engraved overlay.
Stainless steel brushed skull spurs,
men’s size. 13/16” band with stainless
steel floral trim and stainless steel
engraved skull. 1-9/16” shank with
chap guard. Stainless steel floral trim
buttons. 1-3/16” 16-point rowel.
ROCK GRINDER SPUR
MT-23908-9
SPUR WITH LEAF DESIGN
MT-24091-4
1” band with stainless steel
engraved trims. 1-3/8” short drop
down shank. 1-1/2” 16-point rock
grinder rowel (strong effect).
Antique men’s spur with decorative
leaf scrolling, 7/8” band and 2” shank.
MEN’S SPUR
MT-25626
HUMANE SPUR
MT-25628 Ladies’
Stainless Steel 21st Century spur,
3" shank, 1-1/2" band. Knob end.
SPUR, “ROCK GRINDER”
MT-25736-8
SHOW SPUR
MT-25735-1 Men's
SPUR
MT-23905
Stainless Steel 21st Century spur,
3/4" band, 1" shank. Knob end.
SPUR, ROPING
MT-25739Ladies'
Brushed Stainless Steel with deeply Black steel with GS trim bars, 3/4"
engraved full GS trim, 1-3/8” band, band, 9-point rowel.
2-1/4” gooseneck shank with dots,
1-1/4” 16-point “Rock Grinder” rowel.
28
Printed on: 02/28/14
CALF ROPER SPUR
MT-23908-6
1” band with stainless steel
engraved trims and calf roping
motif, 1-3/8” shank, 1” 8-point
rowel. (Mild effect)
SPUR WITH STEER HEAD
MT-24091-6
Antique men’s spur with engraved
steer head inlay, ¾” band and 1-1/2”
shank. Excellent workmanship.
SPUR
MT-25629
Stainless Steel, 21st Century spur,
1-1/2" shank, 3/4" band, Knob end.
SPUR
MT-25755
Black Steel men’s spur with German
Silver engraved trim, 1-3/4” shank,
1” band, 10 point rowel.
Spurs
REINING SHOW SPUR
MT-25762-5
Black satin finish 1-3/8” band with
stainless steel engraved trim. 2-1/4”
g o o s e n e c k shank wi t h d o t s an d
interchangeable 14-point 1-1/2” rowel.
Level three.
YOUTH SPUR
MT-25798
Black Steel with German Silver
engraved trim. 1-3/8" shank, 1/2"
band, 10 point rowel.
RODEO SPUR, 15° Offset
MT-25802-2
Black Steel, 15° offset bull spur,
2-1/4" shank, 1" band, 5 point
notched rowel.
YOUTH SPUR, Chrome
Plated
MT-25814
Engraved band, 1-1/4" shank, 1/2"
band, 10 point rowel.
1-800-654-8547
SPUR
MT-25774
SHOW SPUR
MT-25797
YOUTH SPUR
MT-25797-1
YOUTH SPUR
MT-25798-1
SHOW SPUR
MT-25799
RODEO SPUR, 30˚ Offset
MT-25801-4
Stainless Steel men’s spur, 1-5/8"
shank, 3/4" band, 6 point rowel.
Black Steel with German Silver
engraved trim, 2" shank, 1" band,
sawtooth rowel.
Black Steel, 1/2" plain band, 1-3/8"
shank, 10 point rowel.
Black Steel with German Silver
engraved trim chap guards,
jinglebob, 2-1/4" shank, 3/4" band,
1-3/4", 16 point rowel.
MEN’S ROPING SPUR
MT-25803
RODEO SPUR, 22-1/2°
Offset
MT-25802-3
Black Steel, 22-1/2° Bull Spur,
2-1/2" Shank, 1" Band, 5 point
notched rowel.
STOCK BABY SPUR
MT-25814-1
Nickel plated 1/2” band with 1”
shank and 5/8” rosebud rowel.
Level one.
Stainless Steel, plain band, 2" shank,
3/4" band, 10 point rowel.
YOUTH SPUR, Stainless
Steel
MT-25815
Engraved band, 1-1/4" shank, 1/2"
band, 10 point rowel.
Black Steel, with German Silver
engraved conchos and trim. 1-3/8"
shank, 1/2" band. 9 point rowel.
Black Steel, 30˚ offset bull spur,
2-1/2" shank, 1" band, 5 point
notched rowel.
SPUR
MT-25803-5
B la c k S t e e l S p ur, 2 " S hank ,
Jinglebobs, 1/2" Plain Band, 1-3/4"
Nickel Plated Rowel.
ROPING SPUR
MT-25819 Men's
Stainless, 1-3/4" shank, plain 1/2"
band, rosebud rowel.
29
Printed on: 02/28/14
Spurs
1-800-654-8547
ROPING SPUR
MT-25819-1 Ladies'
Stainless, 1-3/4" shank, plain 1/2"
band, rosebud rowel.
SPUR, ROPER
MT-25819-8
Stainless steel roper spur, 3/4" band,
1" shank, 3/4" rosebud rowel.
GAMBLER SHOW SPUR
MT-25844-6
Antique finish with stainless steel
engraved gambler motif. 1” width
band and 1-3/8” length shank with
chap guard. 12-point 1-5/8” rowel
with jingle bobs.
BABY SPUR
MT-25849-8
Baby spur features antique German
Silver Trim with star cut outs and
rosebud rowel.
ROPING SPUR
MT-25819-4 Ladies'
ROPING SPUR
MT-25819-3 Men's
Stainless Steel, plain band. 1-3/4"
shank, 5/8" band, rosebud rowel.
Stainless Steel, plain band. 1-3/4"
shank, 5/8" band, rosebud rowel.
ROPING SPUR
MT-25831-1 Men’s
ROPING SPUR
MT-25831 Men's
Chrome plated, plain band, 1-3/4"
shank, 1/2" band, 10 point rowel.
Stainless Steel with plain band.
1-3/4" shank, 1/2" band, 10 point
rowel.
ANTIQUE TEAM ROPER
SPUR
MT-25848-9
SPUR
MT-25849-3Youth
Antique spur with engraved GS trim,
longhorn motif, 10-point rowel.
Antique Team Roper spur with 1"
band, German Silver trim, 8 point
blunt rowel.
ROPING SPUR
MT-25850
ROPING SPUR
MT-25850-3
Stainless Steel w/engraved band, 2"
shank, 1/2" band, rosebud rowel.
Stainless Steel w/engraved band,
1-3/4" shank, 3/4" band, rosebud
rowel.
30
Printed on: 02/28/14
YOUTH ROPING SPUR
MT-25819-5
Stainless Steel plain band, 1-3/4"
shank, 5/8" band, rosebud rowel.
ROPING SPUR
MT-25832 Ladies'
Stainless Steel with plain band.
1-3/4" shank, 1/2" band, 10 point
rowel.
SPURS
MT-25849-6
Antique spurs with silver trim with cut
out stars, oval cup, 1-1/4” band and
2-1/2” shank. 9 point rowel.
LADIES’ ROPING SPUR
MT-25850-9
Stainless Steel with rose engraved
band, 1-1/4" shank, 1/2" band, 10
point rowel.
Spurs
QUICK-ON SPUR
MT-25871-1
Ladies’ chrome plated. 9-Point Blunt
Tipped Rowel.
MT-25876-1 Men's
High quality Chrome plated Spring
Steel, Offset Rowel.
ALL AROUND SPUR
MT-25882-1
ROPING SPUR
MT-25886 Men's
CUTTING SPUR
MT-25889
CUTTING SPUR
MT-25889-5
Stainless Steel, plain band, 2" shank,
1" band, 10 point rowel.
Stainless Steel plain band, 2"
shank, 3/4" band, 9 point rowel.
YOUTH SPUR
MT-25924-9Youth
Antique finish with GS bars, skull
motif, 1/2" band, brass buttons and
rowel.
BUMPER SPUR
MT-25878-1
Black satin bumper spur with two
rowels. 7/8" band.
ROPING SPUR
MT-25886-1 Ladies'
Stainless Steel with twisted band,
1-3/4" shank, 1/2" band, 10 point
rowel.
Stainless Steel with twisted band,
1-3/4" shank, 1/2" band, 10 point
rowel.
SPUR
MT-25912
Stainless Steel, men’s spur, plain
band, 2-1/8" shank, 1" band, 14
point rowel.
Stainless Steel men’s spur, 2-1/4"
shank, 1" band, 10 point rowel.
ROPER SPUR
MT-25931
MEN’S TRAINING SPUR
MT-26499
Stainless steel engraved roper spur,
¾” band, 1” shank and ¾” rosebud
rowel.
Antique finish training spur with
stainless steel engraved trim and rope
design. 1-1/4” band, 2-3/8” shank
and rock grinder rowel.
1-800-654-8547
BUMPER SPUR
MT-25878-2
Black satin bumper spur without
rowels. 7/8" band.
YOUTH ROPER SPUR
MT-25886-2
Stainless Steel with twisted band,
1-3/4" shank, 1/2" band, 10 point
rowel.
BLACK CUTTER SPUR
MT-25922
Black Steel 2-1/4" shank, 1-1/4"
band, 8 point rowel.
LADIES’ TRAINING SPUR
MT-26499-1
Antique finish training spur with
stainless steel engraved trim and rope
design. 7/8” band, 2” shank and rock
grinder rowel.
31
Printed on: 02/28/14
Spurs
1-800-654-8547
SPURS
MT-27680-4Men’s
Performer stainless steel brushed All
Around Spur, oval cup, 2-1/8” shank,
1” band and 10 point blunted rowel.
SANTA FE CUTOUT SHANK
MT-28712-3
Antique finish with stainless steel
trims. 1” band width with oval cup.
1-3/8” shank length and 16-point
1-7/8” rowel. Level three.
SANTA FE POINSETTIA SPUR
MT-28713-1
Antique finish with stainless steel
engraved trims. 1” band width, 2” shank
length with chap guard and 20-point
1-1/2” rowel. Level four.
SPURS
MT-27680-5Ladies’
SPUR, LADIES
MT-28020
Performer stainless steel brushed All
Around Spur, oval cup, 2-1/8” shank,
1” band and 10 point blunted rowel.
Ladies antique concave 1” band
with barrel racing motif and trims.
1-3/8” shank with 7/8” 16-point
rowel. Oval cup.
SANTA FE JACK DIAMONDS
SPUR
MT-28711-9
Antique finish with stainless steel trims.
1” band width with oval cup. 1-3/4”
shank length with chap guard. 16-point
1-1/2” rowel.
Level three.
SANTA FE PISTOLS YOUTH SPUR
MT-28712-7
SANTA FE FLORAL CROSS
CONCHO SPUR
MT-28712-6
Antique finish ¾” youth cup band with pistols
motif. 1-1/4” shank with chap guard and
8-point 7/8” rowel. Level one.
Antique finish with floral cross
concho. 1-1/4” band width with
oval cup. 1-3/4” shank length and
1-5/8” rowel. Level three.
SANTA FE ZIA SPUR
MT-28713
Antique finish with stainless
steel engraved trims with Zia
motif. 1-1/16” band width,
2-1/4” shank length with chap
guard and 10-point 1-1/4” rowel.
Level two.
SPUR PINS, 10/pkg
SPUR COTTER PINS
MT-25839-7Brass
MT-25839-5100/pkg
MT-25839-8 Black steel
MT-25839-9 Nickel plated
JINGLE BOB SET
MT-25801-2
Includes 4 jingle bobs, 2 key
rings, 2 cotter pins and 2 spur
pins. Black.
RUBBER SPUR TIEDOWNS
MT-25800-1
Sold per pair.
HEEL STRAPS
MT-13440
7" pair
MT-13441
8" pair
SPUR RACK
MT-25801
Heel strap to hold spurs in place.
Made from 11/16" wide russet leather
with slotted hole in each end.
SPUR TIE DOWNS
MT-25800
Wood spur rack with velvet cover. 16” length. Will work
horizontal or vertical.
Spur tie downs, rubber. 12 pair per card.
32
Printed on: 02/28/14
Rowels
1-800-654-8547
STEEL ROWEL “OILED”
MT-25843-2
Oiled, no plating. 1-1/2" diameter.
16 points. 10 pair per package.
BLACK STEEL ROWEL
MT-25843-6
3/4" diameter. 7 points.
10 pair per package.
ROWEL CARD
MT-25842
BLACK STEEL CLOVERLEAF ROWEL
MT-25845
9 pair, assorted black rowels from
7/8" to 2-3/16" in diameter.
1-3/8" diameter. 10 pair per package.
BLACK STEEL CLOVERLEAF ROWEL
MT-25845-1
1-1/8" diameter. 10 pair per package.
BLACK STEEL ROWEL
MT-25845-2
1-1/4" diameter. 9 points. 10 pair per package.
BLACK STEEL ROWEL
MT-25845-3
1-3/16" diameter. 10 points. 10 pair per package.
ANTIQUE ROWEL CARD
MT-25843
BLACK STEEL ROWEL
MT-25845-4
Features nine pairs of assorted rowels
with pins. 1" to 1-5/8".
1-1/4" diameter. 6 points. 10 pair per package.
BLACK STEEL ROWEL
MT-25842-1
BLACK STEEL ROWEL
MT-25845-5
BLACK STEEL ROWEL
MT-25842-4
BLACK STEEL ROWEL
MT-25845-6
7/8" diameter. 10 pair per package.
1-1/4" diameter. 6 points. 10 pair per package.
1" diameter. 10 pair per package.
1" diameter. 8 points. 10 pair per package.
BLACK STEEL ROWEL
MT-25842-5
BLACK STEEL ROWEL
MT-25845-7
2-3/16" diameter. 10 pair per package.
1-5/8" diameter. 12 points. 10 pair per package.
BLACK STEEL ROWEL
MT-25842-8
BLACK STEEL ROWEL
MT-25845-8
1-1/4" diameter. 10 pair per package.
BLACK STEEL ROWEL
MT-25843-1
1-1/4" diameter. 5 points. 10 pair
per package.
1-1/2" diameter. 10 points. 10 pair per package.
33
Printed on: 02/28/14