Amtronic DVR User Guide Manual

Amtronic DVR
User Guide Manual
Covering all our models
Digital CCTV-surveillance
USER GUIDE MANUAL
AMTRONIC USER GUIDE MANUAL
CONTENTS
NOTICE
Introduction
Precaution before Installation
Warranty Sheet
Warranty Contents
Checking List
System General -----------------------------System Features --------------------------Main Function ----------------------Monitoring Mode ----------------------------Monitoring Mode Explanation -----------------Pan/Tilt Control Method ----------------------Function Setting Methods ---------------------Way of Function Converting ------------------General Setting---------------------------Camera Setting ----------------------------Motion & Display Setting ---------------------Network Setting ----------------------------Sensor Setting -----------------------------User Setting ------------------------------Save -----------------------------------Searching Mode -----------------------------Searching Mode Conversion & Methods --------Multi searching way -------------------------Searching screen Button Explanation -----------Motion Searching Way-----------------------How to use Book Mark ----------------------Data Saving Way---------------------------Log Viewer ----------------------------------Event Backup -------------------------------Image Tool ---------------------------------Backup ------------------------------------Manual Backup Method ----------------------Auto Backup Method ------------------------Backup Viewer -------------------------------DVR Installation -----------------------Front & Back part of the System ---------------Capture Card Connection and Receiver ---------Sensors & Relays Connector Pin Spec (KIT) -------Back I/O B/D with Sensors & Relays (SET) --------Pan/Tilt Camera Protocol --------------------Sound Setting for Audio ----------------------
-2-
6
6
6
7
7
8
10
10
11
13
15
16
18
20
20
21
21
23
24
26
27
29
31
34
35
36
36
38
41
42
42
43
44
44
45
46
USER GUIDE MANUAL
Products Introduction
DVR100, DVR200, DVR1000, DVR3000, DVR1600, DVR3600, DVR2000, DVR4000, DVR2200,
DVR4200, DVR5000 are our series.
Thanks for choosing our products. This manual includes DVR system program setting methods,
functions, features & pan/tilt control connection.
Precaution before Installation
* Please read carefully before you use it.
* Basic function is same even though it is various according to model.
1. Refer to manual before installation, put the power “off” before connecting.
2. Make an enough room for the line.
3. Do not install this around the place where there is magnetic, direct light
heating equipment. (In use temperature 5~35)
4. Install this onto stable place and well-ventilated place.
5. Do not put the heavy objects on this.
6. Do not break this product into pieces.
* Please check the power out if 110/220 voltage.
-3-
USER GUIDE MANUAL
1 System General
This system makes analogue signal into digital signal and save it in HDD, then search those
information when you need. This is what we called DVR (Digital Video Recorder)
1.1 System Features
1) System Stability
We spent more than 4 Years to make our systems stabilized.
2) System File System
We developed the most suitable file system and prevented disk piece in advance,
so we maximize HDD space and minimize disk access time.
For the security reason, we only permitted only authorized users to search our data.
3) Excellent Screen Quality
Saving the clean image when the event happens, so you can see the recording image
very clearly.
4) Convenient user interface
For the user’s convenience, we let the users operate only with mouse clicking.
5) Superior network function expansion
Searching, Displaying, Transmitting are being done at the same time.
Two – Way Audio, Network.
-4-
USER GUIDE MANUAL
2 Monitoring Mode
2.1 Monitoring Mode Explanation
Information display part
(1) Date and Time
(2) Sensor & Alarm, RMS, Backup
(3) Saving degree
(Oldest Basket saving data)
Screen control part
(4) 1, 4, 6, 9, 10, 16 division
(5) Maximum screen
(6) Converting to next camera
(7) Automatic group
(8) PAN TILT CONTROL
(9) Exit button
Camera information display part
(10) Camera shows the current status of camera
Standby recording on record
Not using
Search and Control Part
Search conversion
Log Viewer
Function setting
< How to use Mouse >
1) Screen conversion
- Temporary screen clicking makes screen one division screen.
- Division screen depends on how many screen user want to use.
(As soon as you choose, turns out to be blue)
- If you put auto screen conversion button, Camera group is changing continuously.
- This is the same as click next camera (next group)
2) Full screen
- If you click full button, it turn out to be full screen.
- Click right mouse button makes it turn to previous screen.
< Pop up >
- When you move your mouse, advice for pop up displays.
-5-
Event Backup
USER GUIDE MANUAL
2.2 Pan/Tilt Control Method
When you watch the video and control the view scope of camera or it can be possible to control focus
in/out & zoom in/out.
This is different according to Receiver (refer to Appendix Receiver)
1. PAN/TILT Setting Method
(1) Click setting -> Put the ID & Password, click “OK” -> select the camera in setting mode.
(2) ‘Camera Setting’
... example : Pan/Tilt Receiver is Pelco D (Pelco D, 2400, NONE, 8, 1)
-> Select No.1Camera
-> Check in “use” on Pan/Tilt
-> Select ‘Pelco D’ among the Receiver item.
-> Select ID (ID is Pan/Tilt’s No)
-> Select Speed, Port, Parity, Data Bits, stop Bits list. (2400, NONE, 8, 1)
-> Click ‘OK’
-> Click ‘Save and Exit’
Pan/Tilt Receiver is Pelco D Pelco D,
2400, NONE, 8, 1
Caution during Pan/Tilt operation
Pan/Tilt Receiver has a various of model and protocol. Please check if there is such a kind of
receiver. If this does not work, there might have some problem on line connection or new upgraded
version protocol.
ID is Pan/Tilt’s Number.
-6-
USER GUIDE MANUAL
2. How to use Pan/Tilt
(1)
Click ‘Pan/Tilt’ button, and put ‘ID’ & ‘Password’
(2)
Color turns into blue when it is being used.
(3) Click the icon. You can change following
(left/right) icon.
(4) You can check out all direction with Zoom In/Zoom Out button also.
< Explanation on Controller >
Camera power button/Light power button
Zoom In/ Zoom Out button
Focus In/ Focus Out button
Auto Pan button
2. How to use Preset
< Adding preset >
(1) Click the preset (
) button.
(2) Control the P/T button to where you want to move.
(3) Click the right button and put the ‘Add Preset’
(4) Put the explanation of preset.
< Go to preset >
(1) Click the preset (
)button.
(2) Click the right button at the number, which you want, and put the ‘Go To Preset’.
-7-
USER GUIDE MANUAL
3 Function Setting Methods
3.1 Way of Function Converting
(The shape of icon before/ after)
(1) Click the Setup button.
(2) Put ID & Password.
*REF: Please make sure that nobody except operator
changes this setting mode.
Logging in is made only when operator put ID &
Password.
(3) After logging in, Setting window as left shows up.
This is made of sixth Setting Parts & two Saving
Parts.
- Setting Part: General (System), Camera, Motion &
Display, Network, Sensor & Alarm, and User
- Saving Part: Save & Exit, Exit without Save
-8-
USER GUIDE MANUAL
3.2 General Setting
(4)
(3)
(5)
(2)
(1)
(6)
(1) Initialize : Interval and Initialization
- Composite Monitor display interval : Composite( TV ) Monitor
(Default: 3Sec, Converting ever 3minutes)
- Pan/Tilt Control seeing Composite Monitor : From the composite monitor you can check out moving
image on camera.
- Full Screen : Set for full screen.
- Change color on recording : It turns into red.
- Initial screen split : Initial mode( 1,4,9,16 division )
(2) System Controls
- Shutdown Time : System ending
Ref : If power does not turn off, check CMOS setting mode.
- Use Restarting : Restart of System
- Disable (Ctrl+Alt+Del Key) : This is for not using Key board.
System should be rebooting on Window2000/XP
- Watchdog : System monitoring function (Default: 60 Sec)
(3) Video Mode : You can check NTSC or PAL mode.
(4) Site Location : Putting the name of Users(DVR) (ex, Seoul police station)
(5) Event Log : Event( Motion, Sensor, Video Loss) Log (REF : Log Viewer )
(6) Version Information : You can check out model names, SW version also can be checked.
-9-
USER GUIDE MANUAL
3.3 Camera Setting
(1)
(4)
(5)
(2)
(6)
(7)
(3)
(9)
(8)
(10)
(1) Select Camera
You can choose if you use PTZ, CODEC type, etc.
* Apply same value to all camera : If you want to make all the
function same.
(You can choose if you use PTZ, CODEC type, etc)
(2) Camera Option
- Use: You have to check here after select the camera.
< Extended camera information >
- Camera Name: This let us know the location of
camera at searching mode.
- Other information will be put into RMS
- 10 -
USER GUIDE MANUAL
*REF : Mail server should be
able to support POP3.
- Notify E-Mail on Event
It sends e-mail notice when event happens (Motion, Sensor, Video Loss)
Outgoing mail Server : SMTP Server
From : Sender’s account
Authentication: When you need certification through e-mail server, ask mail server manager.
ID/Password : Put User ID & Password.
To : Address of receiver (about upto 10 persons possible )
Cc : Address of reference persons (about 10 person possible)
Subject : Mail subject
Content : Image will be attached when motion & sensor happens.
- Hide View on PC Monitor : This is very good secret recording without letting anyone note.
- Remove from external monitor rotation : .
- Beep and show one split on event : When motion & sensor happens, is makes one division screen and
beep sound issues.
(3) Pan/Tilt
Refer to 3.2 Pan/Tilt control methods.
(4) Size & Quality Adjustment
- JPEG/MPEG4 choice: Each camera has a different designation.
- Resolution / Quality: Resolution - 320*240(Default) 640*240, 640*480,
Quality - JPEG is 62%, MPEG4 is 62% advisable
*REF
Each model has different FPS rate per mode. For example DVR200, DVR2000, DVR4000 has 120FPS(In case of
NTSC), this is only when 320*240 mode. 640*480 mode has 60~70FPS.
Under PAL type 320*240 mode 100FPS, 640*480 mode 50~60FPS when it is recording.
CPU, Main B/D(Chipset: Intel, Via, SIS, etc), RAM is able to affect on this rate also.
(6) Adjust Camera Frame rate
You can designate every camera’s frame rate.
- 11 -
USER GUIDE MANUAL
* Caution
Recommandation is that Maximum Averaged Frame Rate. If you want to set each different camera’s frame rate, it
should be done within the maximum frame rate it can support.
In case of GED2000: Total frame rate 120FPS, so allow within this scope.
(7) Sound
- Sound : You can choose sound availability. (Mic1~16), Card
- MIC means availability of mike usuage with power on.
- Card means that you are going to use make MIC part of sound card.
(8) Holiday Setup
This is for setting in order to designate one specific date (such as Sunday)
* How to use
1) Select date.
2) Click ‘Add’.
3) Click the date and put ‘Comment’ on list and click ‘Enter key’.
(9) Pre/Post Recording
This designates how many frames you are going to save of (PRE/POST) frames.
(Pre: 10copies, Post: 500copies) Default: Pre – 0, Post – 1
This is for the function in order to record previous one as well as post one.
- 12 -
USER GUIDE MANUAL
(10) Record Scheduling
*How to use
1) Click the designated camera.
2) Click recording scheduling methods button (Normal, Motion, Sensor, etc)
3) Click suitable week day (Mon~Sun), Hour (0~24) or drag & drop.
⇒ Normal : Steady recording during fixed time.
⇒ Sensor : Temporary recording only sensor works.
⇒ Motion : Recording only Motion Detection
⇒ Watch : Only Display not recording.
⇒ Sensor & Motion : Recording under sensor & Motion Detection.
⇒ Normal & Event: Normally 1fps/sec, it is focusing on a specific camera when Motion or Sensor
happens.
3.4 Motion & Display Setting
* How to use
1) Select Camera.
2) Control the screen quality.
*REF: This is not real image but
recording image, so you must be
careful with controlling this.
* Controlling of motion recording
3) Adjust sensor ratio and degree.
Check ‘Display Detected Area and put
‘TEST’ button.
Advisable: Motion ratio 10%
Sensitivity 10%
(1) Color Adjustment
- Color designating: After selecting camera, Brightness, Contrast, Saturation, Hue
can be adjusted. Click ‘Default’ in order to make best condition.
(2) Motion Detection
- Rate of motion: This is a changed image ratio against between previous image and current.
– Sensitivity Adjustment: Pixel (8*8size).
*This plays important parts since when we starts to make a decision first.
- 13 -
USER GUIDE MANUAL
(3) Area Setting
- Whole Area: It sets Detection.
- Partial Area: Setting of partial area for motion detection.
For partial area, put ‘add’ button on Image screen and Drag & Drop. You can make
this partial area boxes up to ten.
(4) Use Relay
It sets how long and which relay to output. (Relay 1~4)
* REF (example)
In case of night shift, it can be notified to no.1 Relay output. (or Siren)
3.5 Network Setting
- Use: Check in ‘Use’ and it permits RMS Connection.
- Video Transfer method: JPEG or MPEG4 mode (In case of Modem, MPEG4 is advisable)
- Notification: When sensor or motion happens, this RMS gives notification by E-Mail.
- 14 -
USER GUIDE MANUAL
* How to use
1) Check in ‘Use’.
2) Select communicating channel. (LAN, ISDN, PSTN)
3) Put Telephone, IP Address. Multi IP can be notified up to 8 places.
* Make Notify Schedule by camera.
4) Select the camera no.
5) Click and Drag & Drop mouse to make scope to designate.
6) In case of Motion & Sensor recording, you can select Event (Motion / Sensor or double
selecting can be possible)
If you set like this, it can send a notification when motion or sensor happens during this
time scope through IP Address, which you already set, beep sound will be released to
user.
- 15 -
USER GUIDE MANUAL
3.6 Sensor & Alarm Setting
(2)
(1)
(3)
(6)
(4)
(5)
(1) Selecting sensor: Choose the sensor number
(2) Option
- Location of sensor: Input the sensor location
- Sensor type: NC(Normal Close) or NO(Normal Open)
- Connected camera : Setting of camera and free set to record when sensor turns on
(3) Sensor Values
- Check Interval: Setting of sensor checking time & interval.
- Output Port: Designate which camera’s recording.
- Output Delay Time : Relay running time setting
(4) Sensor Test: Test status of sensor
* How to use
1) Select camera number 2. Input the sensor location (you do not have to)
3) Select the sensor type (This is a designation for event happening if under NC or NO)
4) Designating connecting camera.
5) When Relay is being used, this makes possible to selct which no. of output.
TEST : This button is able to check if sensor connected or not. This blinks “ in red” when sensor comes
in..
(5) Outer equipment control
Click and input the equipment name (Lamp, ATM, etc), input the start time and ending time.
Then it keeps ‘on’ within setting date and time and turns ‘off’. If you would not use it after setting, select relay
no. and put ‘Del’key.
You can control the this job from the remote site(RMS) such as main controlling center.
- 16 -
USER GUIDE MANUAL
(6) Emergency button
This makes it easier for user to back up data set already from emergency button.
When emergency happens, it sends recording image through RMS and converting and saving.
Button automatically, you can choose only one among sensors.
< Scenario >
When no.3 camera works, all material from no.1.2 camera
should be back up on D:\
It should notify through RMS when sensor and motion
happens.
Setting method (refer to left)
(1) Enter into sensor on setting menu.
(2) Click No.3 ‘sensor’ and check ‘use’
- Emergency button List (3) Check ‘use’ and designate the location and click
‘Browse’
(4) Designate Event Backup Path (Real back up location)
(5) Select camera (No. 1,2 camera)
* Recording material will be saved into when you
designate camera for back up.
(6) Click ‘OK’ network on setting menu.
(7) Check ‘Notification’ in ‘Use’
(8) ‘OK’ – Save and Exit
(1) It should be motion (Event) Below screen will be turned if sensor connects event.
◄ When sensor detects, alarm works.
*REF: Since Event happens, recording is on for 3minutes (Post 3minutes) previous material (Pre
3minutes) will be Backup.
(2) This is a screen of back 3minutes later in
temporary back up path.
*REF: In case of Scenario, Emergency folder will be made in C:\ drive and back up in on.
When Event backup turns up, it should be done before it will be deleted.
- 17 -
USER GUIDE MANUAL
3.7 User Setting
(1)
(2)
(3)
(1) New user add
- Put the user account/ Password, then give the authority (management mode/user mode/
search mode , back up mode, etc)
(2) User list update
- Select user and change the authority and click ‘update ‘ button.
(3) Delete of user
- Click the user and delete it.
* The less user’s authority, the better for our security.
3.8 Save and Exit
- SAVE & EXIT
Exit with the status that keeps what you’ve changed or set.
- EXIT WITHOUT SAVE
- 18 -
USER GUIDE MANUAL
4 Searching Mode
4.1 Search Mode Changing & Methods
(1) Click ‘Search’ button.
- magnified image
(2) Click ‘OK’ after putting Account and Password name.
- Mark the exact ‘Account and Password’
(Default ID: test, Password: test)
- Manage account and password for your own.
- Refer to [3.7 User setting] for more information
◄ Search mode
(3) Select searching date (red
mark)
(previous month)
(next month)
. These red marks mean
currently recording part.
- 19 -
USER GUIDE MANUAL
(4) Click time zone for searching.
(5) First Image will be shown
on screen.
(Refer to date)
(6) Searching is going on
when you put this button
REF: Minute basis searching is available among
60minutes
REF: Hour basis searching among 24hours
Red mark means the location where you are searching.
Different color will be shown according to
recording way
(Normal, Motion, Sensor, etc)
- 20 -
USER GUIDE MANUAL
4.2 Multi Searching Way
When you search the other camera, you can use this function.
(1) Select the minute and hour part to search, then select right part of the searching part (1, 4, 9, 16
division)
<Screen Division >
1 division
4 division
9 divison
16 division
Searching button
(2) When you click divided screen (ex, 4screen) multi searching process(mark as percentage)
and above screen is being showing .
(3) Click and search with search button. Control the “speed” button Normal Speed search is general. If
necessary, user’s designated search will be possible.
* REF: At the multi search, only “multi search” mark is shown on the date & time window no other
specific information shows.
This multi usage is for only simultaneous search function.
At the multi search mode, you can check other camera status as well at the same time. If you click
‘next camera group’ or ‘previous camera group’.
The group is made of 1~4, 5~8, 9~12, 13~16 (4groups). In this mode, only video can be searched not
sound.
- 21 -
USER GUIDE MANUAL
4.3 Search Screen Button Explanation
Date (Year, Month, Day)
Time (Hour, Minute, Second)
Compression CODEC mark (JPEG, MPEG4)
Camera number and file size
Next camera group button choice (4 channel grouping)
Previous group button choice (4 channel grouping)
Conversion to recording mode
When you click this button during searching
job.
1x
1.5x
2x
Panorma
- 22 -
USER GUIDE MANUAL
Searching TOOL (1) – Recording Image quality control button
- Sharp: Make the vague image clear
- Blur: Make the wild image softer
- B/W: Convert color into Black & WHITE
- Cancel: Reverse into previous step, returning button
- Zoom: With the mouse clicking, magnifying the image
- Original: Returning to the first image
Searching TOOL (2) – Saving & Printing of searched image
Color
You can control Brightness, Contrast, Hue
degree
By adjusting this key as you want.
(ex, ease searching at night time)
Speed
Normal Play, Quick Search mode
-Speed is frame/sec for recording& display.
User Setting mode
- Normal Play: Searching through recorded frame speed.
- Quick Search: Fast searching.
- User Setting: Fast or slow searching with speed that fixed by user’s defined value..
- Mute: Deleting of sounding: we can use this when sound and video recorded.
In case of checking: searching only video
In case of not checking: Both video & sound are recorded
Sound
Only video recorded
(Blue) Sound & Video records together
Print
Only video recorded
(Blue) Sound & Video records together
- 23 -
USER GUIDE MANUAL
In case of printer setting done
Left image may show up asking where to print,
select ‘OK’ then you can print out.
In case of printer setting not done
Printer setting advises message comes out
4.4 Motion Searching Way
Under the normal recording mode, designating specific area and analyzing
it .(ex. This is very useful for stolen or lost goods)
(1) Motion rate and
sensibility can be
adjustable.
This is not related with
[3.4 Motion & Display
function setting
methods].
* REF
- Motion ratio is the value between previous video and current one
(The less, the more sensible one. Default: 5%, Recommended: 10~15 %)
- Sensibility is the degree about converting values of picture (8*8 size)
(The less, the more sensible one. Default: 20%, Recommended: 20 %)
- 24 -
USER GUIDE MANUAL
[ Motion Detection on the partial area ]
[ Motion Detection on the partial area ]
(2) Select the whole area button
(2) Select the whole area button
(3) Click ‘Add’ button.
(3) Click the searching button
(4) Drag & Drop in order to make the box.
(up to 5 )
(5) Click the search button.
Motion on the whole area
Motion on the partial area
* Use add, select, delete, delete all button
4.5 How to use Book Mark
Saving location function of current searched recording material (Time, Hour, Minute)
(1) Select Stop button
(2) Click ‘Motion’ button.
- 25 -
USER GUIDE MANUAL
(3) Click ‘Add Book mark’ for book marking
(4) Put the Comments name.
(Being listed on book mark)
This name can be amended.
(1) Click ‘Motion’ button.
(2) When you click Book mark list button, list comes out.
* REF: When there many lists if you select camera/all camera, It will be much better to watch.
In case of Comments name amendment: reinput and click
Short cut: Double click related list or
select it with mouse, then It will be
transferred to this location.
Delete: omit related list
Exit: exit from related list
- 26 -
USER GUIDE MANUAL
4.6 Data Saving Way
Saving function of searched data into disk with the form of JPEG file or AVI (Audio Video Interface) file.
Normal PC can view it.
(1) Still Image(JPEG)
(1) Select Still Image (JPEG)
(2) Click ‘OK’ button
(3) Saving ‘OK’ turns up
(2) Moving Image(AVI)
Procedure (1)~(2) is the same
(3) Check Directory Set part
(4) Designate a specific location with clicking on
‘Browse’ button
(5) If specific file location fixes, put the file
name
(6) Click ‘OK’
(1) Select Moving Image (AVI)
(2) Select Drivers (HDD, CD R/W, OTHER
BACK UP DEVICE)
(3) In case that is not on the specific location,
do not check in Directory Set and click ‘OK’
There left message turns up, if you do not put in
file name
To be continued previously
- 27 -
USER GUIDE MANUAL
(4) Click playing button on Search
(7) Click playing button on Search
Stop
General: The percentage is increasing when searching is going on.
Click the stop button when you need it.
(5) Click the Stop’ button
(6) ‘OK’ message comes out
(7) Click ‘OK’ button.
(8) Click the stop button
(9) ‘OK’ message turns up
(10) Click ‘OK’ button
(3) View of AVI File
Window98 or 2000/XP has Media Player, so find AVI file name and double click it or
Playing Media Player and open ->finding->ok and you can check out saving data.
If you choose caption function on the menu, you can check out
- 28 -
USER GUIDE MANUAL
5 Log Viewer
(1) Click the ‘Log Viewer’ button on
the monitoring mode.
(As follows)
(4)
(1)
(2)
(5)
* REF: If log files
exceed 1MB, old
one remains backup
version and new
one will be created.
All these are left on
Ged log folder.
(6)
(3)
(1) GedLog: log file.
(2) Selected log file
(3) You can search it by time table.
Set up the date/time for searching->click the ‘Search’ button->Log presented on (2)
part.
To reload the old data: Cancel ‘Use’, click ‘Refresh’ button
(4) File Information: Information of log file.
(5) Log Information: Present the log data analysis.
(6) View of event starting point screen in case of Event Log.
(7) Graph : Graph of the event log
- Analized View of graphic according to each event log view.
- 29 -
USER GUIDE MANUAL
View of graphic according to date of
specific date..
Go to previous date/next date of the camera.
Go to next page..
- 30 -
USER GUIDE MANUAL
[3.3] Refer to
camera setting
- Manual: Sending the email just one time.
- Schedule: Send the email frequently.
* As a ‘Schedule Setting’, it send email frequently
when you set this mode
- 31 -
USER GUIDE MANUAL
6 Event Backup
You can use this function for back up the recorded event screen on designated directory. (Refer to 3.6
sensor& alarm (6) Event button)
(1) Click ‘Event Backup’ button
(1) If the message turns up like this, click ‘OK’ button
Lookup Package copying image
(2) Confirm again whether you do Event
Back up or not.
Click ‘ok’ and run the copy
Back up screen
* See the back up search when it is finished.
- 32 -
USER GUIDE MANUAL
7 Image Tool
This program for checking out authentication of FDD, HDD’s JPEG file.
* Water marking function is already equipped
* Way of playing: C:\Program files\DVR, double click imagetool.exe
file
◄ Initial screen of playing
(1) Click ‘Open’
(2) Find & Choose file you
want
(3) Click ‘Open’
Check out the result of authentication
not converted: This is authentic Image.
Converted: This isn’t an authentic Image
(4) Image turns up.
(5) Click ‘Verify Image’ button.
* REF: Other information: Camera no. Camera Name, Saving Time, Authority, User, Window
Product key
- 33 -
USER GUIDE MANUAL
8 Backup
This is a part for back up into other saving equipment. There are Manual back/auto back up for user’s
convenience. You can always check out at anywhere.
* REF: You can not do both auto/manual back up.
< SUPPORTING BACK UP DEVICE >
HDD, DVD, DAT, CDRW, ONSTREAM, DLT, MO, ZIP, NETWORK DRIVE IF devices are DAT,
ONSTREAM,DLT (LINEAR ACCESS device), we need a program which is converting LINEAR
ACCESS device into RANDOM ACCESS device. (ex: DTA, DATMAN, ONSTREAM ECHO
SOFTWARE ETC)
8.1 Manual Backup Method
Backing up what user want to pick up. Selecting Date->Camera->Time->Minute.
(1) Double click this.
* REF: to begin manually
1) Begin->Program->DVR->Backup
2) C:\Program Files\DVR\Backup.exe
(2) Data Loading is on the way
(3) Put the Account & Password
(4) Click ‘OK’.
Change of icon color
Back up is done (White)
Back up is going
- 34 -
USER GUIDE MANUAL
(5) Click ‘Select Media’
(6) Select back up device.
(7) Click ‘OK’.
(8) Users are designating Date->Camera->Hour
->Minute
* REF
Checking point is to be backed up.
With back up window open,
The most recent information Refreshes.
(9) Click ‘Back up start’ button.
(10) if you need package, click ‘OK’
If you do not need it, click ‘Cancel’
Lookup Package is a program to
make it
i
B k d t
(11) LookupPackage is copying on.
(12) Click ‘Yes’
This is reconfirming if you want to Back up on related
back up media
(13) Click ‘Yes’ This is the confirming message that moving to the last part
of recent back up area and let it do auto back up.
* After finishing back up, Refer to 2.10 Backup way in order to check out if you want to
know if it well done.
- 35 -
USER GUIDE MANUAL
8.1 Auto Backup Method
Automatic backing up with operating specific time scheduler.
< Variety of Backup >
1) DAILY BACKUP
Mark Monday to Sunday and back up the previous data.
2) Minute basis BACKUP
Back up after designating minute and begin backing up. ex) If you set up 2minutes basis it is doing
continuously. MAIN DISK& BACKUP device has two minutes difference.
3) BASKET BACKUP
Designating BASKET number and if in BASKET DATA is full BACKUP starts...
1. Automatic Backup Setting
(1) Moving to auto back up screen.
This is the point where the
last back up done as well as
auto back up starting point.
(2) Click ‘Add’ button or select
related month/date
and click ‘Add’ with right
mouse part.
Auto Startup
Autoback definitely
needs to be marked
here
LOG: Backup record stay here
VIEW: back up searching program
HIDDEN: Window hidden
EXIT: Getting out of back up program
- 36 -
USER GUIDE MANUAL
(3) Select the camera to back up
(4) Select Backup device
(5) Designate the location of related saving
device
Select All: select all camera at one
time
(7) Select the kind of back up
(8) Click ‘Finish’ button
Active
When you use scheduler, if you do
not use it, do not check here.
(9) ’OK’ button makes whole day’s back up
time same.
‘CANCEL’ button makes specific date for
back up.
- 37 -
USER GUIDE MANUAL
2. Auto Backup Update
This Job is done under “update” column as below. List can be shown as below when you click right
button of mouse.
ADD : NEW SCHEDULE ADDS
UPDATE : SCHEDULE AMENDS
DELETE : SCHEDULE DELETES
CLEAR ALL : ALL SETTING SCHEDULE
ARE BEING DELETED
3. Others
< Media exchange >
When CD is full and it needs to confirm, if you want
to go or not. If you want to go on format CD click
‘OK’
< BACKUP LOG View >
There Only 1 log for one job when It runs.
BACKUP LOG (Following) – Auto back up size25 MB
- 38 -
USER GUIDE MANUAL
9 Backup Viewer
This is a program for viewing back up material on a general PC or DVR.
< Program running methods >
1) Running at DVR
(Run lookup.exe file in C:\Program Files\DVR folder.)
2) General PC running methods:
copy LookupPackage.exe (Backup viewer)on backup search program and open (automatically),
C:\Program Files\Lookup is made , then you can run backup.exe
(1) Click the icon
(2) Click year, month, date folder
(4) When it shows screen,
begin to search with searching button
◄ Exit button
◄ Water marking is on
SAVING : image recording on FDD
PRINT: printing
SPEED: searching speed control/ mute (no sound)
ORIGINAL: watching original
* If mute is checked, sound does not play.
* You can control speed accordingly.
- 39 -
USER GUIDE MANUAL
10 Installation
10.1 Front or Back part of the System
Front
Reset Button
HDD LED
Power Switch
CD-RW
Back
Overlay Board
(RCA jack use)
camera(1~16)
Sensor/Relay
Connection
Power
connection
Blue: mouse
Purple: keyboard
VGA Card
Capture Card
Ethernet interface
* Front / Back picture can be different according to model and upgraded status
- 40 -
USER GUIDE MANUAL
10.2 Capture Card Connector and Receiver
Capture Card Jumper J11 is for RS232, J12 is for RS422/485
Camera
PTZ
Camera
Receiver
①
JP1
On: 485 Mode
Off: 422 Mode
②
DVR
COM1
J12(J32)
J11(J31)
COM2
Line 1 connecting way: J12 (J32) port should be connected to PTZ Camera or Receiver
Please refer to following.
422Mode
1pin:RX2pin:RX+
3pin: TX4pin:TX+
485Mode
1pin:TX-/RX2pin:TX+/RX+
J11(or J31)port should be connected to PC serial port(COM1 or COM2). And Please check
In PTZ box on camera setting, Set the port COM1 or COM2(set according to outer connection)
Set the each protocol different according to receiver. Cable spec of line 2 is as below.
[ 9 pins ]
Com1/2
[ 25 pins ]
J11(J31)
Com1/2
J12(J32)
(rx+) 2
2 (rx+)
(rx+) 2
2 (rx+)
(tx+) 3
3 (tx+)
(tx+) 3
3 (tx+)
(gnd) 5
5 (gnd)
(gnd) 5
5 (gnd)
(rts) 7
7 (rts)
(rts) 7
7 (rts)
- 41 -
USER GUIDE MANUAL
10.3 Sensors & Relays Connector Pin Spec
SENSOR
3~12V DC
Lamp Or Siren
1A 30V DC
0.5A 125V AC
- 42 -
USER GUIDE MANUAL
10.5 Pan/Tilt Camera Protocol setting Values by Receiver
index
Receiver
0
Dvna
Baud
rate
9600
1
DY
2
Parity
Data Bit
N
8
Stop
Bit
1
9600
N
8
1
Fine
2400
N
8
1
3
Linlin
9600
N
8
1
4
Panasonic
19200
N
8
1
5
Pelco D
2400
N
8
1
6
Philips
9600
N
8
1
7
Serim
9600
N
8
1
8
Sungjin
4800
M
8
1
9
Vicon_1200R
4800
N
8
1
10
Dyuni
9600
E
8
1
11
DyuniTech_DRX50
9600
N
8
1
12
MP200
9600
N
8
1
13
KD6
9600
N
8
1
14
Samsung
9600
N
8
1
15
Oriental
4800
O
8
1
16
Techwin
9600
N
8
1
17
OmniView
9600
N
8
1
18
CNB
9600
N
8
1
19
CTNCOM
9600
N
8
1
20
Niko
2400
N
8
1
21
Winnertec
2400
N
8
1
22
PT-101
9600
N
8
1
23
PanasonicV12
24
Vicon_15UVS
25
Securtex_B
4800
N
8
1
26
SmileCAM
19200
N
8
1
27
SCANDOMWE-2
9600
N
8
1
28
BBV
9600
N
8
1
29
KRE301
N
8
1
30
AD_RAS715LS
8
1
31
KALATEL_KTD312
8
1
32
VIDEOLARM
8
1
33
PELCO P
8
1
- 43 -
Auto
Pan
O
X
O
O
O
O
X
X
X
O
O
O
O
X
O
O
O
O
X
X
O
O
O
O
O
O
O
O
O
X
X
X
X
X
Preset
X
O
X
X
X
O
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
O
X
X
O
X
X
X
X
X
X
O
USER GUIDE MANUAL
10.6 Sound Setting Method
Audio volume should be controlled in PC which has RMS installed S/W for sound recording
< How to use >
(1) Start->Program->Sub program
->Entertainment->Volume control
(2) If you click ‘Option->Properties’, you
can see ‘properties info’ window
(3) Check the mike volume on the properties
information box of volume controller
Sound card mixer equipment
(4) Click ‘Advanced’ for mic input
Option-Advanced.
- 44 -
USER GUIDE MANUAL
(5) Check the mike output volume
at other control part.
Check Microphone Boost List.
It can show +20db Gain in some cases.
You can use recorder function to check
Mike output before & after checking)
You must check if sound input is working
well. Checking is being done as follows;
Start->program->Sub program
->Entertainment->Sound recorder.
*REF: Select ‘mute’ box if you want to save the voice directly without letting it
go through speaker or only out put voice through speaker.
This is the same as way adapted to 2way audio on RMS.
Sometimes in case sound card does not support microwave amplifying function
‘advanced” button does not show up
In this case, High sensible amplified mike should be in use
- 45 -