RIDI Green Box A4 8S_en_int_Layout 1 - ridi
Transcription
RIDI Green Box A4 8S_en_int_Layout 1 - ridi
The complete answer Energy-efficient lighting control Efficient louvre materials Simple installation For 600/625 modular ceilings Complete package of square luminaires for modular ceilings in a variety of sizes: 2-axis, 3-axis and 4-axis. Illuminance group 2 (daylight dependent) +30% 100 100 80 40 Illuminance group 1 (daylight dependent) % 100 70 50 10 3-phase mains or 4-phase mains + pushbutton Simple installation using the linect plug-in system The luminaires are fitted with the Linect connection system for maximum ease of installation: % - se + ha -p Presence / daylight sensor and control unit integrated in the master luminaire. 2 Slave Group 2 Presence sensor: With a pick-up range of 4 m x 4 m, the sensor responds to even minor movements. Increasing the pick-up range to 5 m x 6 m extends the detection field for larger movements. The pick-up range can be increased using upgrade sensor DALI-AL-PIR. Master Group 1 Slave Group 1 Slave Group 2 Sensor alignment Installation Minimal planning work required Short installation times Simple lay-in mounting of luminaires in modular ceilings Foolproof installation as luminaires are connected from the outside using a coded connector No need to open the luminaire Connecting cables, T-junctions, plugs and sockets are all included. max. 3,5m 6m 5m Pushbutton optional for manual operation 6m 5m Daylight sensor: The system is set in the factory for a nominal illuminance of 600lx with 30% reflection. The sensor actuates two different luminaire groups. Luminaire group 2 is controlled with a 30% offset relative to group 1, which is located nearest to the window. Individual adjustments are possible using optional DALI-AL-FB1/FB2 remote control units. Depending on the degree of daylight and on the presence of a person in the room, the lighting system can be controlled in two different operating modes using the RIDI Green Box basic components: * Average electricity price = 1.18 € p.a. Cost savings per annum appr. 100€ Highly efficient lighting technology due to use of silver-coated aluminium (MIRO SILVER) for the louvre and top reflector material with a total light reflection factor of 98%. 88,3 71,4 50% 100% Energy savings With presence detection + daylight detection/deactivation Savings of up to 75% due to: Highly efficient louvre and mirror material Presence-dependent control Daylight-dependent control 24% Eta_LB 0% Actuation takes place through the master luminaire for up to 7 additional slave luminaires in 2 groups for different levels of brightness on the window / corridor side depending on the daylight control setting. The master luminaire must be positioned as part of luminaire group 1 on the window side. For presence detection, the master luminaire must also be placed in proximity to the desk or workstation. Standard Aluminium SG Top reflector SG – specular With daylight detection/ deactivation Single office 2080 Medium 0,18 TLD / EVG-DALI 2 2 70 (4x18w) 1 175 kWh p.a. 32 € p.a.* With presence detection RIDI Green Box Single office Room type 2080 Operating hours/p.a. Medium Daylight influence 0,18 Price kWh (Euro) TLD / KVG Lamps / operation 4 luminaires window side luminaires corridor side Output per luminaire 85,2 (4x18w) Output per luminaire Lighting control system Energy consumption 709 kWh p.a. Energy consumption Energy costs 128 € p.a.* Energy costs 20% 60% 70% 75% Existing installation from the 80s, tri-band 26 mm dia. fluorescent lamp with EVG, white louvre Existing system Room type Operating hours/p.a. Daylight influence Price kWh (Euro) Lamps / operation No. of luminaires Existing installation from the 70s, standard 38 mm dia. fluorescent lamp with KVG, opal diffuser luminaire Exchanging an existing lighting system for the RIDI Green Box components can bring real energy savings! Energy consumption 100% Mode 2: Open-plan office If the level of daylight is too low AND there is someone present in the room, the lighting system switches on. When there is no longer anyone present, the lighting system dims automatically with a delay of 15 minutes and switches off after 120 minutes. 50% Mode 1: Single office If the level of daylight is too low AND there is someone present in the room, the lighting system switches on. When there is no longer anyone present, the lighting system switches off automatically with a delay of 15 minutes. Lamps in colour 840 are already prefitted in the luminaires. Lamps have already been burnt in for 100 h, allowing the system to be commissioned and dimmed immediately on completed installation. Parabolic mirror louvre SG – specular What the RIDI Green Box has to offer: Energy saving potential of up to 75% Simple lay-mounting Connection with colour-coded linect plug-in system Integrated presence and daylight sensor Ultra-efficient lighting technology Prefitted lamps ready burnt in for 100 hours to allow immediate dimming following installation SG-MIRO SILVER KS Louvre/reflector material Lamps, louvre / reflector material 0% Light control Presence and daylight sensor T16 , matt or specular louvre Luminaire versions with T16 lamps for 625 and 600 modular ceilings Voltage: ~230-240V,50-60HZ Master luminaire design - EBRE 424 SG-MR / EBRME 424 SG-MR Approvals: Protection class: Single steel luminaire, coated white with low rim. Top reflector in MIRO SILVER. 4 x T16 24W lamps prefitted. Equipped with a presence and daylight sensor with its own control unit. Dimmable ballast, compatible with the DALI standard. Dimming range 1-100%. Parabolic mirror louvre SG in specular MIRO SILVER. Slave luminaire design - EBRE 424 SG-SL / EBRME 424 SG-SL EBRE/EBRME 424 SG h [%] 80.7 Phi_u [%] 100 Phi_o [%] 0 LITG_DIN A 60 UTE 0.81B Single steel luminaire, coated white with low rim. Top reflector in MIRO SILVER. 4 x T16 24W lamps prefitted. Dimmable ballast, compatible with the DALI standard. Dimming range 1-100%. Parabolic mirror louvre SG in specular MIRO SILVER. 3-phase mains or 4-phase mains + pushbutton IP 20 Slave Group 2 Master Group 1 Slave Group 2 Slave Group 1 Master luminaire design - EBRE 424 SM-MR / EBRME 424 SM-MR Single steel luminaire, coated white with low rim. Top reflector in MIRO SILVER. 4 x T16 24W lamps prefitted. Equipped with a presence and daylight sensor with its own control unit. Dimmable ballast, compatible with the DALI Standard. Dimming range 1-100%. Parabolic mirror louvre SM in silk matt MIRO SILVER. luminaire box set Slave luminaire design - EBRE 424 SM-SL / EBRME 424 SM-SL EBRE/EBRME 424 SM h [%] 80.3 Phi_u [%] 100 Phi_o [%] 0 LITG_DIN A 60 UTE 0.80B Single steel luminaire, coated white with low rim. Top reflector in MIRO SILVER. 4 x T16 24W lamps prefitted. Dimmable ballast, compatible with the DALI Standard. Dimming range 1-100%. Parabolic mirror louvre SM in silk matt MIRO SILVER. EBRE for 625 modular ceilings Mounting dimensions: LE = 604 mm LB = 604 mm LE = 579 mm LB = 579 mm 597 622 Mounting dimensions: linect socket 597 8 60 T16 lamp (light colour 840) prefitted and burned in for 100 h! Complete sets comprising master luminaire, slave luminaires, connecting cables, plug and socket components, prefitted lamps. Underside of luminaires fitted with protective film to be removed after installation. 597 622 60 Slave Group 1 luminaire linect socket 622 +2 Slave Group 2 box set Slave luminaire linect socket 6 luminaire 60 Slave luminaire Slave Group 1 box set Master luminaire linect socket 622 +2 Slave Group 2 EBRME for 600 modular ceilings Master luminaire 4 = 5-phase connecting cable, 4 metres, with linect socket, blue, I coding - | N | PE | L | DA | DA | 597 = 5-phase linect connector block, dark grey, L coding - | N | PE | L | L’ | N’ | 60 = 5-phase linect socket, dark grey, L coding - | N | PE | L | L’ | N’ | = 5-phase linect connector block, blue, I coding - | N | PE | L | DA | DA | T26 , Specular louvre Voltage: Luminaire versions with T26 lamps for 625 modular ceilings ~230-240V,50-60HZ Protection class: Approvals: Master luminaire design - EBRE 418 GAG-MR Single steel luminaire, coated white with low rim. Top reflector in MIRO SILVER. 4 x T26 18W lamps prefitted. Equipped with a presence and daylight sensor with its own control unit. Dimmable ballast, compatible with the DALI standard. Dimming range 1-100%. Parabolic mirror louvre GAG in specular MIRO SILVER. EBRE 418 GAG h [%] 88.1 Phi_u [%] 100 Phi_o [%] 0 LITG_DIN A 60 UTE 0.88B Slave luminaire design - EBRE 418 GAG-SL Single steel luminaire, coated white with low rim. Top reflector in MIRO SILVER. 4 x T26 18W lamps prefitted. Dimmable ballast, compatible with the DALI standard. Dimming range 1-100%. Parabolic mirror louvre GAG in specular MIRO SILVER. 3-phase mains or 4-phase mains + pushbutton IP 20 Slave Group 2 Master Group 1 Slave Group 2 Slave Group 1 EBRE for ceiling module 625 Master luminaire Slave luminaire luminaire box set 622 622 Mounting dimensions: linect socket linect socket 622 LE = 614 mm LB = 604 mm +2 Slave Group 2 Slave Group 1 622 60 4 60 6 luminaire box set +2 Slave Group 2 Slave Group 1 8 luminaire box set T26 lamp (light colour 840) prefitted and burned in for 100 h! Complete sets comprising master luminaire, slave luminaires, connecting cables, plug and socket components, prefitted lamps. Underside of luminaires fitted with protective film to be removed after installation. = 5-phase connecting cable, 4 metres, with linect socket, blue, I coding - | N | PE | L | DA | DA | = 5-phase linect connector block, dark grey, L coding - | N | PE | L | L’ | N’ | = 5-phase linect socket, dark grey, L coding - | N | PE | L | L’ | N’ | = 5-phase linect connector block, blue, I coding - | N | PE | L | DA | DA | 4 6 8 RIDI Green Box T26 for 625 modular ceilings:: Article no. Designation 1837605 RIDI-GREEN-BOX EBRE 4X418 GAG luminaire box set 1837606 RIDI-GREEN-BOX EBRE 6X418 GAG 1837607 RIDI-GREEN-BOX EBRE 8X418 GAG luminaire box set luminaire box set 4 6 8 RIDI Green Box T16 for 625 modular ceilings: Article no. Designation 1837611 RIDI-GREEN-BOX EBRE 4X424 GAG luminaire box set 1837612 RIDI-GREEN-BOX EBRE 6X424 GAG 1837613 RIDI-GREEN-BOX EBRE 8X424 GAG luminaire box set luminaire box set 4 6 8 RIDI Green Box T16 für Modul 625: Article no. Designation 1837617 RIDI-GREEN-BOX EBRE 4X424 MAG luminaire box set 1837618 RIDI-GREEN-BOX EBRE 6X424 MAG 1837619 RIDI-GREEN-BOX EBRE 8X424 MAG luminaire box set luminaire box set 4 6 8 RIDI Green Box T16 für Modul 600: Article no. Designation 1837614 RIDI-GREEN-BOX EBRME 4X424 GAG luminaire box set 1837615 RIDI-GREEN-BOX EBRME 6X424 GAG 1837616 RIDI-GREEN-BOX EBRME 8X424 GAG luminaire box set luminaire box set 4 6 8 RIDI Green Box T16 für Modul 600: Article no. Designation 1837620 RIDI-GREEN-BOX EBRME 4X424 MAG luminaire box set 1837621 RIDI-GREEN-BOX EBRME 6X424 MAG 1837622 RIDI-GREEN-BOX EBRME 8X424 MAG luminaire box set luminaire box set comprising 1x EBRE 418 GAG-MR 3x EBRE 418 GAG-SL 1x EBRE 418 GAG-MR 5x EBRE 418 GAG-SL 1x EBRE 418 GAG-MR 7x EBRE 418 GAG-SL comprising 1x EBRE 424 SG-MR 3x EBRE 424 SG-SL 1x EBRE 424 SG-MR 5x EBRE 424 SG-SL 1x EBRE 424 SG-MR 7x EBRE 424 SG-SL comprising 1x EBRE 424 SM-MR 3x EBRE 424 SM-SL 1x EBRE 424 SM-MR 5x EBRE 424 SM-SL 1x EBRE 424 SM-MR 7x EBRE 424 SM-SL comprising 1x EBRME 424 SG-MR 3x EBRME 424 SG-SL 1x EBRME 424 SG-MR 5x EBRME 424 SG-SL 1x EBRME 424 SG-MR 7x EBRME 424 SG-SL comprising 1x EBRME 424 SM-MR 3x EBRME 424 SM-SL 1x EBRME 424 SM-MR 5x EBRME 424 SM-SL 1x EBRME 424 SM-MR 7x EBRME 424 SM-SL 625 modular ceilings T26 lamp Specular louvre 625 modular ceilings T16 lamp Specular louvre 625 modular ceilings T16 lamp Matt louvre 600 modular ceilings T16 lamp Specular louvre 600 modular ceilings T16 lamp Matt louvre Optional accesories Article no. 0208191 DALI-AL-FB1 Simple tool for mode selection (mode 1 and 2), light value calibration Article no. 0208190 DALI-AL-FB2 Selection tool (mode 1-10/ mode 1 and 2 + 8 other modes), light value calibration Article no. 0208221 DALI-AL-FB0 Two-button transmitter for switching and dimming functions Article no. 0208266 DALI-AL-WH0 Wall holder for DALI-AL-FB0 RIDI Leuchten GmbH • Hauptstraße 31-33 • D-72417 Jungingen Tel. 0 74 77/8 72-0 • Fax 0 74 77/8 72-48 • Internet www.ridi.de • eMail [email protected] © RIDI Leuchten GmbH / 0000 266 / 08/2010 / T / Despite all due care in the compilation of this flyer, freedom from printing and other errors cannot be guaranteed. We reserve the right to make formal and technical changes. Article no. 0208308 DALI-AL-PIR Sensor upgrade for movement detection. For ceiling mounting.
Similar documents
Recessed LED luminaires EBRE-LED, EBRME - ridi
from 2700 to 6500 Kelvin. LED driver prefitted in luminaire housing. Operation at safety extra-low voltage below 60 Volt (SELV-conformity). Suitable for direct voltage operation and use in emergenc...
More information