KAMATICS “KRP” CATALOG

Transcription

KAMATICS “KRP” CATALOG
KAMATICS “KRP” CATALOG
TRACK ROLLERS, CAM FOLLOWERS, AIRFRAME PIVOT BEARINGS
KAMATICS CORPORATION
P. O. Box 3 (1330 Blue Hills Avenue)
Bloomfield, CT USA 06002
860-243-9704, fax 860 243-7993
Rev G, May 2011
Kamatics Sales Offices
Please Contact Kamatics for Your Local Representative Worldwide
Bloomfield, CT USA
860-243-9704
fax 860-243-7993
www.kamatics.com
Page 2
TABLE OF CONTENTS
KAMATICS “KRP” Catalog…
KARON Lined Track Rollers,
Cam Followers &
Airframe Pivot Bearings
Please review the Kamatics KAron Design Guide, “KRP”
section, and pages 3, 4 & 5 of this catalog for information
about the unique Kamatics design approach to solving the
more common problems associated with grease lubricated
needle, roller and ball bearings. As “KRP” components are
manufactured from corrosion resistant materials, a selflubricating liner, along with a large bearing surface,
problems plaguing rolling element bearings such as
brinnelling, corrosion and lack of lubrication are nonexistent.
See the KAron Design Guide for liner choices and a
description of the liners available. KAron V is
recommended for general high load roller applications. For
those applications where operating temperatures exceed
+250 F (+120 C) KAron B or KAtherm T87 is
recommended. KAron F or VS is recommended for
applications with low operating pressures, 5000 psi (35
2
N/mm ) or less. Contact Kamatics engineering for
assistance in selecting a liner system for your application.
Track/Cam Followers (Needle bearing replacements)
KRP 562 Series
KRP 567 Series
NAS 562 Series
Dimensional Equivalent
KRP 562 Series with
Crowned Outer Race
Track Rollers (Roller bearing replacements)
KRP 502 Series
MS24465 Series
Dimensional Equivalent
KRP 503 Series
MS24466 Series
Dimensional Equivalent
KRP 522 Series
KRP 502 Series with
Crowned Outer Race
KRP 523 Series
Heavy Duty Track Roller
Series
KRP 527 Series
Self-Aligning Track Roller
Series
Heavy Duty Pivot Bearings (Needle bearing
replacements)
KRP 505 Series
MS24461 Series
Dimensional Equivalent
KRP 506 Series
MS24462 Series
Dimensional Equivalent
Airframe Pivot Bearings (Ball bearing replacements)
KRP( ) Series
MS27640 Series
Dimensional Equivalent
KRP( )A Series
MS27641 Series
Dimensional Equivalent
KRP( )B Series
MS27642 Series
Dimensional Equivalent
KRP( )BS Series
MS27648 Series
Dimensional Equivalent
KRP( )P Series
MS27644 Series
Dimensional Equivalent
KRPB500 Series
MS27646 Series
Dimensional Equivalent
Page 3
Page
English Metric
6
21
7
22
8
23
9
24
10
25
11
26
12
27
13
28
14
29
15
30
16
31
17
32
18
33
19
34
20
35
KAMATICS “KRP”
Track Roller, Cam Follower & Pivot
Bearings:
The design and manufacture of self-lubricating track
rollers, cam followers and typical airframe pivot bearings
was and continues to be pioneered by Kamatics
Corporation. It was obvious that there was an unfulfilled
need for this type of bearing that would not be subject to
the effects of corrosion, brinnelling, ball/roller/needle
fracture and difficulty to grease that is common to
conventional anti-friction bearings.
The need to
continually re-lubricate, the manpower required, not
being sure that the lubricant ever reached the bearing,
was and continues to be a concern. Also, by eliminating
the grease requirement, the environment around the
bearing remains much cleaner and not subject to the
collection of grit, dirt etc. that is also common around
greased assemblies. Looking under the wing or at a
landing gear of a greased aircraft is enough to make one
aware of the potential benefits of non-greased selflubricated bearings.
Track Rollers & Cam Followers:
For the majority of track roller/cam follower applications
the “KRP” design incorporates a KAron liner applied to
the OD of the inner race and. Either KAron or PTFE filled
Acetal resin is inserted between the side faces of the
outer race and thrust members. This provides an
additional benefit to the roller by providing a thrust
capability not usually found in an anti-friction bearing of
the same type. The outer race is made from a hard
corrosion resistant stainless steel material, normally
Custom 455, 440C or Cronidur 30 stainless steel, and a
17-4 PH stainless steel inner race and thrust member(s).
Depending upon the operating conditions, seals are
included to minimize the entry of abrasive particles and
contaminating fluids.
The assembly is then either
electron beam welded or swaged to keep the
components together as an assembly.
Figure 1
illustrates this Kamatics design approach.
arrangement or is cantilevered off of structure. Of
concern for a cantilevered (studded) roller is determining
where the roller will contact the mating track or cam.
Figure 2 shows a studded roller assembly.
Figure 3, (self-aligning roller)
Figure 2, (stud mounted roller)
The worst-case scenario is when the roller contact is at
the extreme end of the outer race, away from the
threaded end. The bending moment arm is the longest at
this point, imparting maximum stress on the stud. This is
not a problem unless the stud is not of sufficient size to
safely react the implied stress. There are various
methods to analyze the bending stresses in a
cantilevered roller and this is normally the responsibility
of the bearing user. The same concern as to where the
outer race will contact the mating surface exists with a
clevis-mounted assembly, however, the bending
consideration is at a minimum. The concern here is more
of track/cam contact and bolt shear stresses. Bolt shear
is usually not a major concern as there is double shear
involved with a clevis arrangement.
There are ways to minimize the bending concern on a
studded roller. One is to incorporate a “crown” radius on
the OD of the roller in an attempt to bring the contact
point nearer the center of the outer race width. This is
the most common approach with anti-friction bearings,
however, this ensures that the contact stresses on the
track or cam will be high because of the more localized
contact area. This is not a problem as long as the
stresses are within the material’s capabilities.
A second approach to minimizing both the bending and
contact stress considerations is the patented Kamatics
self-aligning roller. This design incorporates a KAron
lined spherical inner race that operates against the same
hardened outer race material as the more common
“KRP” design. The spherical feature allows the roller to
conform/align to the mating track/cam surface without the
high contact stresses and with a reduced bending
moment arm that can be considered to pass through the
centerline of the outer race width. Figure 3 illustrates the
self-aligning design.
Figure 1 (clevis mounted roller)
The design and load carrying capability of track rollers
and cam followers depends heavily on the installation.
That is, whether the bearing is installed between a clevis
Extensive testing and field results have shown that a
KAron lined track roller will operate successfully for an
extended duration at dynamic bearing pressures as high
as 20,000 psi (140 mPa). For most commercial
aircraft flap/slat roller applications or similar, by
keeping the bearing pressures to a maximum of
12,000 psi (85mPa), the roller can yield in excess of
200,000 revolutions of useful life with liner wear less
than 0.004 inches (0.10mm). As is obvious, if as many
as 200,000 revolutions are not required, the bearing
pressures can be increased. This is normally the case of
military aircraft, where space is small, loads are higher
but the number of cycles is lower. Kamatics engineering
is available to assist in sizing the roller for any application
under consideration.
“KRP” Linkage/Bellcrank Pivot Bearings:
Prior to the Kamatics self-lube KRP design, the typical
linkage/bellcrank pivots bearings were mainly limited to
ball bearings or greased journal bearings. The “KRP”
design for these applications also incorporate a design
similar to the track roller/cam follower with an internal
self-lube liner, but without the hardened outer race.
Because this type of bearing is contained/pressed within
a housing the need for a hardened outer race does not
normally exist. In “linkage/bellcrank” KRP, the self-lube
liner is applied to the ID and side faces of the outer race
and the inner race is of sufficient hardness to provide the
hard, abrasion-resistant surface necessary for optimum
performance. Figure 4 illustrates this design.
Figure 4
(“KRP” Linkage/Bellcrank Bearing)
Table 8 of the Kamatics KAron Design Guide offers
some recommended housing and shoulder dimensions
for installation.
Page 4
This Kamatics “KRP” catalog offers self-lubricated designs that are dimensionally equivalent to many of the more commonly used ball, needle and roller bearings used in industry today. They all
feature the benefit of a liner system that is not prone to problems associated with anti-friction bearings. Problems such as race brinnelling, rolling element failure, greasing difficulties (including
the requirement to get the grease to the bearing) and the manpower needed to maintain the bearing.
For load-carrying capability of a KRP bearing, calculations based on the projected area concept, described in the Kamatics KAron Design Guide, and similar to that discussed for Kamatics
journal bearings should be used. A KRP linkage/bellcrank bearing normally experiences race oscillation as opposed to race rotation for track roller/cam follower bearings. The data in the
Kamatics KAron Design Guide, Table 7 along with Equations 3 or 4 and 5 can be used to determine potential liner wear.
TABLE 1
Liner
KAron B
High Load
KAron V
High Load / Low
Friction
KAron F
Low Friction
KAron VS
Low Friction
KAtherm T87
High Speed /
High
Temperature
500°F (260°C)
Approximate Physical
Properties
Density – 1.51 gm/cc
Hardness Rockwell M95
Thickness Range .005 .060” (.127 – 1.5 mm)
Characteristics
Typical Applications
Dynamic operating Pressures to
50,000 psi (345 mPa).
Velocities to 3 fpm (1 M/min.)
Temp Range –100° to 400° F
(-73° to >205°C)
SAE AS81820 & SAE AS81934
Qualified
Aircraft controls, landing gears etc.
Track rollers.
Cam followers
Highly loaded linkages.
Jet engine controls.
Other high loaded demanding,
maintenance free applications.
Density – 1.36 gm/cc
Hardness Rockwell M85
Thickness Range .005 .060” (.127 – 1.5 mm)
Dynamic operating Pressures to
40,000 psi (276 mPa).
Velocities to 10 fpm (3 M/min.)
Temp Range –100° to 300° F
(-73° to 150°C)
Mil-B-8943 Qualified
Track rollers.
Cam followers.
Marine/naval applications.
Aircraft shock struts.
Other high loaded, low friction
applications.
Density – 1.36 gm/cc
Hardness Rockwell M85
Thickness Range .003” –
min. (.076 mm min.)
Rubbing surface is a
predominately PTFE enriched
outer surface, providing low
coefficient of friction at low loads
and at low temperatures. The
general operating parameters are
the same as KAron V. A minimum
thickness liner of .003” (.076 mm)
can be obtained. Dynamic
operating pressures up to 20,000
psi (138 mPa)
Dynamic operating pressures up
to 15,000 psi (103mPa), excellent
low temperature friction
capabilities. Temp Range –100° to
300° F
(-73° to 150°C)
Dynamic operating Pressures to
20,000 psi (140 mPa).
Velocities to 30 fpm (9 M/min.)
Temp Range –100° to 500° F
(-73° to 260°C)
Designed for SAE AS81819
Spherical bearings
Track rollers.
Cam followers
Other moderately high loaded, low
friction applications
Density – 1.56 gm/cc
Hardness Rockwell 15X 88
Thickness Range .005 .060” (.127 – 1.5 mm)
Density – 1.37 gm/cc
Hardness Rockwell M80/90
Thickness Range .005 .030” (.127 – .75 mm)
Page 5
Spherical bearings
Track rollers.
Cam followers
Other moderate loaded, low friction
applications
Formulated for high temperature
applications to 500°F (260°C) such
as VG bushings, engine linkages,
thrust reverser, cam followers,
track rollers and helicopter rotor
control bearing
Track Rollers, Cam Followers & Airframe Bearings
KRP 562 Series – Studded, Self-Lubricating,
Track Roller, Cam Follower Bearings
Dimensionally Equivalent to NAS 562 Series
STUD LENGTH
SEE NOTE 1
KARON
LINER
GRIP LENGTH
+,-.016
H
SEALS
M
L
KRP 562– 6 V T
"Z" FOR SEAL
ADD
.016
REF
Part Number Example:
OPTION
G
D
F
A
THREAD LENGTH
THREADS MAX
.10 MIN
SCREW DRIVER SLOT
OR HEX HOLE
KRP562
SERIES
BEARING
NUMBER
KRP562-3
KRP562-4
KRP562-5
KRP562-6
KRP562-7
KRP562-8
B
STUD
DIA
+.000
- .001
.190
.250
.312
.375
.437
.500
D
H
ROLLER
OUTER
DIA.
+.0010
-.0005
.5000
.6875
.7500
.8750
1.0000
1.1250
STANDARD
OUTER
STUD &
RACE
THRUST RING
B
S 2 INCOMPLETE
T
ROLLER
WIDTH
+.005
-.005
.281
.281
.344
.469
.531
.656
F
DIST TO
COTTER
PIN
HOLE
1900-32
.2500-28
.3125-24
.3750-24
.4375-20
.5000-20
.211
.224
.234
.265
.283
.314
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
KARON
(SEE TABLE
1 FOR
LINER
OPTIONS)
S
L
M
N
G
P
T
A
THREAD
LENGTH
(REF)
KEYWAY
LENGTH
+.030
-.000
N/A
.337
.327
.416
.452
.515
KEYWAY
RUNOUT
(REF)
KEY
WIDTH
+.002
-.002
N/A
.0635
.0635
.0947
.0947
.1260
SLOT
DEPTH
+.010
-.010
N/A
.2143
.2738
.3236
.3861
.4330
HOLE
DIA
+.010
-.000
.070
.076
.076
.106
.106
.106
TRACK
CONTACT
WIDTH
MIN
.230
.230
.290
.380
.430
.530
RING
DIA
(REF)
MIN
.344
.344
.359
.359
.422
.422
N/A
.437
.437
.500
.562
.625
.40
.57
.59
.72
.84
.97
SUFFIX DESIGNATION
ADD SUFFIX
AMS 5617
CUSTOM
455
Rc 47 MIN
D
For all Sizes:
Radial Play = .0015 to .0035 inches
Axial Play = .005 to .015 inches
THREAD
SIZE
UNJF-3A
PER
MIL-S-8879
LINER
K – 16 S
KRP = KAron Track Roller Bearing Prefix
562 = Studded Roller Series, Crowned Outer Race
–6 = .3750 Stud Diameter (Diameter in 1/16 increments)
V = KAron V Liner (See Table 1 for liner Options)
T = Track Roller Designation (not optional in p/n)
Z = Add “Z” for Seal Option
A = Add “A” for NO Cotter Pin Hole
K = Add “K” for Keyway Option
–16 = 1.000 Stud Grip Length (Length in 1/16 Increments)
S = Add “S” for PH13-8MO CRES Stud Option.
D = Add “D” for 440C Outer Race Option
N
P
Z A
ADD SUFFIX
ADD SUFFIX
S
D
Z
TO P/N FOR AMS 5629
(PH13-8MO)
Rc 43 MIN (COND
H1000 REF), STUD &
THRUST RING
TO P/N FOR
AMS 5630
(440C) Rc 55-62
OUTER RACE
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
Page 6
NOTES:
1. Stud Length = Nominal Grip Length + “S” Thread
Length, +.031, -.016
2. Load ratings shown are based on KAron V liner
system.
3. Loads shown are based on bearing components only,
stud bending not considered.
RADIAL
STATIC
LIMIT
LOAD
(LBS)
See Notes
2&3
2925
3625
5290
10000
13325
18200
Track Rollers, Cam Followers & Airframe Bearings
STUD LENGTH
SEE NOTE 1
KARON
LINER
SLOT OR
HEX HOLE
KRP 567 Series – Studded, Self-Lubricating
Crowned Outer Race, Track Roller, Cam
Follower Bearings
Otherwise Dimensionally Equivalent to KRP 562 Series
GRIP LENGTH
+,-.016
H
SEALS
M
L
KRP 567– 6 V T
"Z" FOR SEAL
ADD
.016
REF
Part Number Example:
OPTION
G
D
F
A
THREAD LENGTH
THREADS MAX
.10 MIN
RAD
KRP567
SERIES
BEARING
NUMBER
KRP567-3
KRP567-4
KRP567-5
KRP567-6
KRP567-7
KRP567-8
B
S 2 INCOMPLETE
C CROWN
B
STUD
DIA
+.000
- .001
.190
.250
.312
.375
.437
.500
D
ROLLER
OUTER
DIA.
+.0010
-.0005
.5000
.6875
.7500
.8750
1.0000
1.1250
STANDARD
OUTER
STUD &
RACE
THRUST RING
H
ROLLER
WIDTH
+.005
-.005
.281
.281
.344
.469
.531
.656
F
DIST TO
COTTER
PIN
HOLE
1900-32
.2500-28
.3125-24
.3750-24
.4375-20
.5000-20
.211
.224
.234
.265
.283
.314
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
KARON
(SEE TABLE
1 FOR
LINER
OPTIONS)
S
L
M
N
G
P
C
A
THREAD
LENGTH
(REF)
KEYWAY
LENGTH
+.030
-.000
N/A
.337
.327
.416
.452
.515
KEYWAY
RUNOUT
(REF)
KEY
WIDTH
+.002
-.002
N/A
.0635
.0635
.0947
.0947
.1260
SLOT
DEPTH
+.010
-.010
N/A
.2143
.2738
.3236
.3861
.4330
HOLE
DIA
+.010
-.000
.070
.076
.076
.106
.106
.106
CROWN
RADIUS
(INCHES)
(REF)
6
6
7
8
10
12
RING
DIA
(REF)
MIN
.344
.344
.359
.359
.422
.422
N/A
.437
.437
.500
.562
.625
.40
.57
.59
.72
.84
.97
RADIAL
STATIC
LIMIT
LOAD
(LBS)
See Notes
2&3
2925
3625
5290
10000
13325
18200
SUFFIX DESIGNATION
ADD SUFFIX
AMS 5617
CUSTOM
455
Rc 47 MIN
D
For all Sizes:
Radial Play = .0015 to .0035 inches
Axial Play = .005 to .015 inches
THREAD
SIZE
UNJF-3A
PER
MIL-S-8879
LINER
K – 16 S
KRP = KAron Track Roller Bearing Prefix
567 = Studded Roller Series, Crowned Outer Race
–6 = .3750 Stud Diameter (Diameter in 1/16 increments)
V = KAron V Liner (See Table 1 for liner Options)
T = Track Roller Designation (not optional in p/n)
Z = Add “Z” for Seal Option
A = Add “A” for NO Cotter Pin Hole Option
K = Add “K” for Keyway Option
–16 = 1.000 Stud Grip Length (Length in 1/16 Increments)
S = Add “S” for PH13-8MO CRES Stud Option.
D = Add “D” for 440C CRES Outer Race Option
N
P
Z A
ADD SUFFIX
ADD SUFFIX
S
D
Z
TO P/N FOR AMS
5629 (PH13-8MO)
COND H1000
Rc 40 MIN, STUD &
THRUST RING
TO P/N FOR AMS
5630
(440C) Rc 55 MIN,
OUTER RACE
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
Page 7
NOTES:
1. Stud Length = Nominal Grip Length + “S” Thread
Length, +.031, -.016
2. Load ratings shown are based on KAron V liner
system.
3. Loads shown are based on bearing components only,
stud bending is not considered.
KRP 502 Series – KAron Lined, Self-Lubricating,
Track Roller, Cam Follower
Track Rollers, Cam Followers & Airframe Bearings
W
Part Number Example:
KRP 502– 06 V T Z
H
KARON
LINER
D
Dimensionally Equivalent to MS24465 Series
ADD
E
B
"Z" FOR SEAL
OPTION
D
KRP = KAron Track Roller Bearing Prefix
502 = Non-Studded Roller Series
–06 = .3750 Bore Diameter (Diameter in 1/16 increments)
V = KAron V Liner (See Table 1 for liner Options)
T = Track Roller Designation (not optional in p/n)
Z = Add “Z” for Seal Option
D = Add “D” for 440C Outer Race Option
A
For all Sizes:
Radial Play = .0015 to .0035 inches
Axial Play = .005 to .015 inches
LASER OR ELECTRON
BEAM WELD
T
KRP502
SERIES
BEARING
NUMBER
KRP502-03
KRP502-04
KRP502-06
KRP502-08
KRP502-10
KRP502-12
KRP502-14
OUTER
RACE
AMS 5617
CUSTOM 455
Rc 47 MIN
B
D
W
H
E
A
BORE
DIA
+.0000
- .0005
.1900
.2500
.3750
.5000
.6250/.6243
.7500/.7493
.8750/.8743
ROLLER
OUTER
DIA.
+.0000
-.0010
.7500
.8750
1.0625
1.3125
1.5000
1.7500
2.0000
INNER
RACE
WIDTH
+.000
-.005
.312
.375
.500
.625
.750
1.000
1.125
OUTER
RACE
WIDTH
+.000
-.005
.218
.281
.375
.500
.625
.875
1.000
RADIUS OR
45 DEG
CHAMFER
TO CLEAR
FILLET RAD
.022
.022
.022
.032
.032
.032
.032
INNER
RACE
THRUST
RING
LINER
DESIGNATION
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
KARON
(SEE TABLE 1
ADD SUFFIX
Z
D
FOR
LINER
OPTIONS)
TO P/N FOR
SEAL OPTION
(ACETAL
RESIN
OR NYLON)
TO PART NUMBER
FOR
440C OUTER RACE
AMS 5630 Rc 55-62
Page 8
ADD SUFFIX
T
THRUST
RING
DIA
(REF)
.63
.68
.94
1.12
1.25
1.50
1.62
TRACK
CONTACT
WIDTH
MIN
.125
.218
.312
.438
.562
.750
.875
RADIAL
STATIC
LIMIT
LOAD
(LBS)
See Notes
1&2
AXIAL
STATIC
LIMIT
LOAD
(LBS)
WEIGHT
LBS
(REF)
4095
6665
11935
20930
29675
52000
76700
2035
2490
3465
4520
5500
6555
7760
.03
.06
.10
.19
.30
.55
.85
NOTES:
1. Load ratings shown are based on KAron V liner
system.
2. Loads shown are based on bearing components
only, bolt/pin shear not considered.
Track Rollers, Cam Followers & Airframe Bearings
KRP 503 Series – Self-Lubricating, Airframe, Pivot
& Track Roller Bearings
Dimensionally Equivalent to MS24466 Series
W
KARON
LINER
D
Part Number Example:
KRP 503– 06 V T Z
H
ADD
E
B
D
KRP = KAron Track Roller Bearing Prefix
503 = Non-Studded Roller Series
–06 = .3750 Bore Diameter (Diameter in 1/16 increments)
V = KAron V Liner (See Table 1 for liner Options)
T = Track Roller Designation (not optional in p/n)
Z = Add “Z” for Seal Option
D = Add “D” for 440C Outer Race Option
"Z" FOR SEAL
OPTION
A
For all Sizes:
Radial Play = .0015 to .0035 inches
Axial Play = .005 to .015 inches
LASER OR ELECTRON
BEAM WELD
T
KRP503
SERIES
BEARING
NUMBER
KRP503-06
KRP503-08
KRP503-10
KRP503-12
KRP503-14
OUTER
RACE
AMS 5617
CUSTOM 455
Rc 47 MIN
B
D
W
H
E
A
BORE
DIA
+.0000
- .0005
.3750
.5000
.6250/.6243
.7500/.7493
.8750/.8743
ROLLER
OUTER
DIA.
+.0000
-.0010
1.1250
1.3750
1.6250
1.8750
2.1250
INNER
RACE
WIDTH
+.000
-.005
1.000
1.250
1.500
1.750
2.000
OUTER
RACE
WIDTH
+.000
-.005
.875
1.125
1.375
1.625
1.875
RADIUS OR
45 DEG
CHAMFER
TO CLEAR
FILLET RAD
.022
.032
.032
.032
.032
THRUST
RING
DIA
(REF)
.94
1.12
1.33
1.58
1.72
TRACK
CONTACT
WIDTH
MIN
.750
1.000
1.125
1.375
1.625
RADIAL
STATIC
LIMIT
LOAD
(LBS)
See Notes
1&2
AXIAL
STATIC
LIMIT
LOAD
(LBS)
WEIGHT
LBS
(REF)
30160
48750
75565
102375
141440
3615
4670
5650
6630
7535
.25
.45
.74
1.14
1.65
NOTES:
1. Load ratings shown are based on KAron V liner system.
INNER
RACE
THRUST
RING
LINER
DESIGNATION
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
KARON
(SEE TABLE 1
ADD SUFFIX
ADD SUFFIX
Z
D
FOR
LINER
OPTIONS)
TO P/N FOR
SEAL OPTION
(ACETAL
RESIN
OR NYLON)
TO PART NUMBER
FOR
440C OUTER RACE
AMS 5630 Rc 55-62
Page 9
T
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
Track Rollers, Cam Followers & Airframe Bearings
KRP 522 Series – Track Roller,
Crowned Outer Race
W
D
Similar to KRP 502 Series with Crowned Outer Race
H
KARON
LINER
ADD
E
B
(2 PL)
"Z" FOR SEAL
Part Number Example:
KRP 522– 06 V T Z
OPTION
KRP = KAron Bearing Prefix
522 = Crowned Track Roller Series
–06 = .3750 Bore Diameter (Diameter in 1/16 increments)
V = KAron V Liner (See Table 1 for liner Options)
T = Add “T” for Track Roller (not optional in p/n)
Z = Add “Z” for Seal Option
D = Add “D” for 440C Outer Race Option
A (2 PL)
LASER OR ELECTRON
BEAM WELD
Cr
R (2 PL)
T
KRP522
SERIES
BEARING
NUMBER
KRP522-03
KRP522-04
KRP522-06
KRP522-08
KRP522-10
KRP522-12
KRP522-14
KRP522-16
KRP522-20
KRP522-24
KRP522-28
KRP522-32
KRP522-36
KRP522-40
KRP522-44
D
B
D
W
H
BORE
DIA
+.0000
- .0007
.1900
.2500
.3750
.5000
.6250
.7500
.8750
1.0000
1.2500
1.5000
1.7500
2.0000
2.2500
2.5000
2.7500
ROLLER
OUTER
DIA.
+.0000
-.0010
.7500
.8750
1.0025
1.3125
1.5000
1.7500
2.0000
2.1250
2.2500
3.0010/2.9988
3.4385/3.4363
3.8760/3.8738
4.3135/4.3113
4.7510/4.7488
5.0010/4.9988
INNER
RACE
WIDTH
+.000
-.010
.312
.375
.500
.625
.750
1.000
1.125
1.187
1.250
1.500
1.500
1.500
1.500
1.500
1.500
OUTER
RACE
WIDTH
+.000
-.015
.280
.345
.455
.580
.705
.950
1.075
1.137
1.200
1.440
1.440
1.440
1.440
1.440
1.440
OUTER
RACE
INNER
RACE
THRUST
RING
LINER
AMS 5617
CUSTOM
455
Rc 47 MIN
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
KARON
(SEE TABLE 1
FOR
LINER
OPTIONS)
E
45 DEG
CHAMFER
+.010
-.000
.022
.022
.022
.032
.032
.032
.032
.032
.032
.032
.032
.032
.032
.032
.032
DESIGNATION
ADD SUFFIX “Z”
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
ADD SUFFIX “D”
TO PART NUMBER
FOR
440C OUTER RACE
AMS 5630 Rc 55-62
Page 10
A
THRUST
RING
DIA
(REF)
.44
.52
.67
.84
.95
1.11
1.22
1.63
1.75
2.00
2.28
2.56
2.86
3.11
3.34
R
CORNER
RADIUS
+.010
-.000
.022
.022
.022
.032
.032
.032
.032
.032
.032
.032
.032
.032
.032
.032
.032
CROWN
RADIUS
(REF)
RADIAL
STATIC
LIMIT
LOAD
(LBS)
See Notes
1&2
WEIGHT
LBS
(REF)
10.0
10.0
10.0
12.5
17.5
25.0
27.5
30.0
30.0
60.0
60.0
60.0
60.0
60.0
60.0
4800
7700
13000
23000
35000
52500
66700
82400
104000
145000
163500
181500
207000
226500
236000
.03
.06
.10
.19
.30
.55
.85
1.30
1.75
2.20
2.90
3.60
4.50
5.40
5.60
Cr
NOTES:
1. Load ratings shown are based on KAron V liner system.
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
3. For all Sizes:
Radial Play = .0015 to .0035 inches
Axial Play = .005 to .015 inches
Track Rollers, Cam Followers & Airframe Bearings
KRP 523 Series – Self-Lubricating, Airframe,
Pivot & Track Roller Bearings
Typical Aircraft High Load Flap Track Roller Series
W
KARON
LINER
D
H
ADD
E
B
Part Number Example:
KRP 523– 06 V T Z
"Z" FOR SEAL
OPTION
D
KRP = KAron Track Roller Bearing Prefix
523 = Non-Studded Roller Series
–06 = .3750 Bore Diameter (Diameter in 1/16 increments)
V = KAron V Liner (See Table 1 for liner Options)
T = Track Roller Designation (not optional in p/n)
Z = Add “Z” for Seal Option
D = Add “D” for 440C Outer Race Option
A
For all Sizes:
Radial Play = .0015 to .0035 inches
Axial Play = .005 to .015 inches
LASER OR ELECTRON
BEAM WELD
T
KRP503
SERIES
BEARING
NUMBER
KRP523-04
KRP523-06
KRP523-08
KRP523-10
KRP523-12
KRP523-14
KRP523-16
KRP523-20
KRP523-24
KRP523-28
KRP523-32
B
D
W
H
E
BORE
DIA
ROLLER
OUTER
DIA.
INNER
RACE
WIDTH
OUTER
RACE
WIDTH
RADIUS OR
45 DEG
CHAMFER
+.0000
- .0005
.2500
.3750
.5000
.6250
.7500
.8750
1.0000
1.2500
1.5000
1.7500
2.0000
+.000
-.001
.8750
1.1250
1.3750
1.6250
1.8750
2.1250
2.3750
2.7500
2.9988/3.0010
3.4363/3.4385
3.8738/3.8760
+.000
-.005
.750
1.000
1.250
1.500
1.750
2.000
2.250
2.500
2.750
3.000
3.000
+.000
-.005
.710
.940
1.190
1.440
1.690
1.940
2.190
2.440
2.690
2.940
2.940
+.010
-.000
.022
.022
.032
.032
.032
.032
.032
.032
.032
.032
.032
OUTER
RACE
INNER
RACE
THRUST
RING
LINER
AMS 5617
CUSTOM 455
Rc 47 MIN
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
KARON
(SEE TABLE 1
FOR
LINER
OPTIONS)
DESIGNATION
ADD SUFFIX
Z
TO P/N FOR
SEAL OPTION
(ACETAL
RESIN
OR NYLON)
ADD SUFFIX
D
TO PART NUMBER
FOR
440C OUTER RACE
AMS 5630 Rc 55-62
Page 11
A
T
TRACK
CONTACT
WIDTH
MIN
RADIAL
STATIC
LIMIT
LOAD
(LBS)
See Notes
1&2
THRUST
RING
DIA
(REF)
WEIGHT
LBS
(REF)
.52
.67
.84
.95
1.11
1.22
1.58
1.63
2.00
2.28
2.56
.58
.75
1.00
1.13
1.38
1.63
1.88
2.03
2.28
2.63
2.63
16500
29000
50000
76000
98000
127000
173000
223000
283000
350000
388000
.12
.25
.45
.74
1.14
1.65
2.30
3.30
4.10
5.80
7.30
NOTES:
1. Load ratings shown are based on KAron V liner system.
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
Track Rollers, Cam Followers & Airframe Bearings
W
KARON
LINER
"O" RING SNUBBER
OPTION (BOTH SIDES)
KRP 527 Series – KAron Lined, Self-Aligning, SelfLubricating, Track Roller/ Cam Follower Series
H
SEAL/SNUBBER
(BOTH SIDES)
Part Number Example:
KRP 527 08 V T
KRP = KAron Bearing Prefix
527 = Self-Aligning Roller Series
–08 = .5000 Bore Diameter (Diameter in 1/16 increments)
V = KAron V Liner (See Table 1 for liner Options)
T = Track Roller Application
B
D
S
(2 PL)
2 DEGREE MIN.
MISALIGNMENT
For all Sizes:
Radial Play = .0030 inches maximum
Rotational Torque (no-load) = 2 inch-pounds maximum
E(2 PL)
C
(2 PL)
A
ELECTRON
BEAM WELD
INSERT
KRP527
SERIES
B
D
W
H
E
A
C
S
BEARING
NUMBER
BORE
DIA
+.0000
- .0007
ROLLER
OUTER DIA.
+.0000
-.0010
INNER RACE
WIDTH
+.000
-.010
OUTER RACE
WIDTH
+.000
-.005
45 DEG
CHAMFER
+.010
-.000
INNER RACE
SPHERICAL
DIA
(REF)
CORNER
RADIUS
(MINIMUM)
CLAMP-UP
DIAMETER
(REF)
KRP527-04
KRP527-06
KRP527-08
KRP527-10
KRP527-12
KRP527-14
.2500
.3750
.5000
.6250
.7500
.8750
.8750
1.1250
1.3750
1.6250
1.8750
2.1250
.750
1.000
1.250
1.500
1.750
2.000
.656
.940
1.190
1.440
1.690
1.940
.022
.022
.032
.032
.032
.032
.610
.800
.968
1.200
1.375
1.620
.020
.040
.050
.050
.050
.050
.52
.67
.84
.91
1.11
1.22
OUTER RACE
& INSERT
INNER RACE
AMS 5617
CUSTOM 455
Rc 47 MIN
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
SEAL / SNUBBER
LINER
PTFE / ELASTOMER
KARON
(SEE TABLE 1 FOR
LINER OPTIONS)
RADIAL
STATIC
LIMIT
LOAD
(LBS)
See Notes
1&2
12600
20100
27500
49000
52400
71300
NOTES:
1. Load ratings shown are based on KAron V liner system.
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
Page 12
WEIGHT
LBS
(REF)
.12
.25
.45
.74
1.14
1.65
Track Rollers, Cam Followers & Airframe Bearings
R
Dimensionally Equivalent to MS24461 Series
W
(2 PL)
KARON
LINER
D
KRP 505 Series – Self-Lubricating Airframe, Pivot
& Track Roller Bearings
H
ADD
"Z" FOR SEAL
Part Number Example:
KRP 505– 06 V T Z
A
KRP = KAron Bearing Prefix
505 = Airframe/Pivot/Roller Series
–06 = .3750 Bore Diameter (Diameter in 1/16 increments)
V = KAron V Liner (See Table 1 for liner Options)
T = Add “T” for Track Roller (Custom 455 Outer Race) Option
Z = Add “Z” for Seal Option
D = Add “D” for 440C Outer Race Option
P = Add “P” for OD Cadmium Plate Option (per QQ-P-416
Type II, Class 2)
B
E
OPTION
(2 PL)
LASER OR ELECTRON
BEAM WELD
KRP505
SERIES
BEARING
NUMBER
KRP505-03
KRP505-04
KRP505-05
KRP505-06
KRP505-07
KRP505-08
KRP505-09
KRP505-10
KRP505-12
KRP505-14
KRP505-16
KRP505-20
KRP505-24
KRP505-28
KRP505-32
KRP505-36
KRP505-40
KRP505-44
KRP505-48
KRP505-52
B
D
W
H
E
BORE
DIA
+.0000
- .0005
.1900
.2500
.3125
.3750
.4375
.5000
.5625/.5618
.6250/.6243
.7500/.7493
.8750/.8743
1.0000/.9993
1.2500/1.2493
1.5000/1.4993
1.7500/1.7493
2.0000/1.9993
2.2500/2.2493
2.5000/2.4993
2.7500/2.7493
3.0000/2.9993
3.2500/3.2492
ROLLER
OUTER
DIA.
+.0000
-.0005
.6875
.7500
.8125
.8750
.9375
1.1250
1.1875
1.2500
1.3750
1.6250
1.7500
2.0000/1.9994
2.2500/2.2494
2.5000/2.4994
2.7500/2.7494
3.0000/2.9994
3.2500/3.2492
3.5000/3.4992
3.7500/3.7492
4.0000/3.9992
INNER
RACE
WIDTH
+.000
-.005
.312
.375
.437
.562
.625
.750
.875
1.000
1.125
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
OUTER
RACE
WIDTH
+.000
-.005
.218
.281
.344
.469
.531
.656
.781
.906
1.000
1.125
1.125
1.049
1.049
1.049
1.049
1.049
1.049
1.049
1.049
1.049
RADIUS OR
45 DEG
CHAMFER
TO CLEAR
FILLET RAD
.022
.022
.022
.022
.032
.032
.032
.032
.032
.032
.032
.032
.032
.032
.032
.032
.032
.032
.032
.032
OUTER
RACE
INNER
RACE
THRUST
RING
LINER
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
KARON
(SEE TABLE 1
FOR
LINER
OPTIONS)
A
R
THRUST
RING
DIA
(REF)
.53
.61
.64
.72
.78
.97
1.03
1.09
1.22
1.47
1.55
1.80
2.05
2.30
2.55
2.80
3.05
3.30
3.55
3.80
RADIUS OR
45 DEG
CHAMFER
+.010
-.000
.022
.022
.022
.022
.032
.032
.032
.032
.032
.032
.032
.032
.032
.032
.032
.032
.032
.032
.032
.032
DESIGNATION
ADD SUFFIX “Z”
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
ADD SUFFIX “T” FOR
TRACK ROLLER OPTION
AMS 5617 OUTER RACE
CUSTOM 455 Rc 47 MIN
Rev D May 5, 2004 : KRP505-()VT OPTION WAS 440C
Page 13
ADD SUFFIX “D”
TO PART NUMBER
FOR
440C OUTER RACE
AMS 5630 Rc 55-62
D
P
RADIAL
STATIC
LIMIT
LOAD
(LBS)
See Notes
1&2
AXIAL
STATIC
LIMIT
LOAD
(LBS)
WEIGHT
LBS
(REF)
4055
6665
9165
15445
19890
28665
35570
42640
56810
73710
85315
102375
119440
136500
153565
170625
187690
204750
221915
238875
2035
2485
2940
3465
3920
4520
4965
5425
6405
7385
8440
10325
12210
14090
15975
17890
19745
21630
23510
25470
.03
.04
.05
.07
.09
.17
.22
.27
.34
.53
.58
.69
.79
.90
1.00
1.11
1.22
1.33
1.43
1.50
NOTES:
1. Load ratings shown are based on KAron V liner
system.
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
3. For all Sizes:
Radial Play = .0015 to .0035 inches
Axial Play = .005 to .015 inches
Track Rollers, Cam Followers & Airframe Bearings
R
Dimensionally Equivalent to MS24462 Series
W
(2 PL)
KARON
LINER
D
KRP 506 Series –Self-Lubricating, Airframe, Pivot
& Track Roller Bearings
H
ADD
B
E
Part Number Example:
KRP 506– 06 V T Z
"Z" FOR SEAL
D
P
KRP = KAron Bearing Prefix
506 = Airframe/Pivot/Roller Series
–06 = .3750 Bore Diameter (Diameter in 1/16 increments)
V = KAron V Liner (See Table 1 for liner Options)
T = Add “T” for Track Roller (Custom 455 Outer Race) Option
Z = Add “Z” for Seal Option
D = Add “D” for 440C Outer Race Option
P = Add “P” for OD Cadmium Plate Option (per QQ-P-416
Type II, Class 2)
OPTION
A
(2 PL)
For all Sizes:
Radial Play = .0015 to .0035 inches
Axial Play = .005 to .015 inches
LASER OR ELECTRON
BEAM WELD
KRP506
SERIES
BEARING
NUMBER
KRP506-03
KRP506-04
KRP506-05
KRP506-06
KRP506-07
KRP506-08
KRP506-10
KRP506-12
KRP506-14
KRP506-16
KRP506-20
B
D
W
H
E
BORE
DIA
+.0000
- .0005
.1900
.2500
.3125
.3750
.4375
.5000
.6250
.7500
.8750
1.0000
1.2500
ROLLER
OUTER
DIA.
+.0000
-.0010
.6250
.6250
.6875
.7500
.8125
1.0000
1.1250
1.2500
1.3750
1.5000
1.8750
INNER
RACE
WIDTH
+.000
-.005
.625
.562
.625
.812
.875
.875
.875
1.125
1.125
1.125
1.375
OUTER
RACE
WIDTH
+.000
-.005
.500
.500
.500
.750
.750
.750
.750
1.000
1.000
1.000
1.250
RADIUS OR
45 DEG
CHAMFER
TO CLEAR
FILLET RAD
.022
.022
.022
.022
.022
.032
.032
.032
.032
.032
.032
OUTER
RACE
INNER
RACE
THRUST
RING
LINER
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
KARON
(SEE TABLE 1
FOR
LINER
OPTIONS)
A
R
THRUST
RING
DIA
(REF)
.51
.51
.57
.63
.69
.88
1.00
1.12
1.25
1.38
1.75
RADIUS OR
45 DEG
CHAMFER
+.010
-.000
.022
.022
.022
.022
.022
.032
.032
.032
.032
.032
.032
ADD SUFFIX “T” FOR
TRACK ROLLER OPTION
AMS 5617 OUTER RACE
CUSTOM 455 Rc 47 MIN
Rev D May 5, 2004 : KRP506-()VT OPTION WAS 440C
Rev G Dec 23, 2008: MS24462 was MS24461
Page 14
AXIAL
STATIC
LIMIT
LOAD
(LBS)
WEIGHT
LBS
(REF)
11600
10580
14255
22425
26210
30890
36970
48670
56785
72760
111815
2035
2335
2790
3315
3695
4370
5350
6255
7235
8140
10025
.05
.04
.06
.08
.09
.14
.16
.25
.28
.31
.61
NOTES:
1. Load ratings shown are based on
KAron V liner system.
DESIGNATION
ADD SUFFIX “Z”
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
RADIAL
STATIC
LIMIT
LOAD
(LBS)
See Notes
1&2
ADD SUFFIX “D”
TO PART NUMBER
FOR
440C OUTER RACE
AMS 5630 Rc 55-62
2. Loads shown are based on
bearing components only, bolt/pin
shear is not considered.
Track Rollers, Cam Followers & Airframe Bearings
C
Dimensionally Equivalent to MS27640 Series
W
(2 PL)
KARON
LINER
H
ADD
D
KRP ( ) Series – Self-Lubricating Airframe/Pivot
Bearings
"Z" FOR SEAL
E
B
Part Number Example:
KRP 06 V Z P
OPTION
KRP = KAron Bearing Prefix
–06 = .3750 Bore Diameter (Diameter in 1/16 increments)
V = KAron V Liner (See Table 1 for liner Options)
Z = Add “Z” for Seal Option
P = Add “P” for OD Cadmium Plate Option (per QQ-P-416
Type II, Class 2)
A
For all Sizes:
Radial Play = .0015 to .0035 inches
Axial Play = .005 to .015 inches
(2 PL)
LASER OR ELECTRON
BEAM WELD
KRP( )
SERIES
BEARING
NUMBER
KRP03
KRP04
KRP05
KRP06
KRP08
KRP10
B
D
W
H
E
A
C
BORE
DIA
+.0000
- .0005
.1900
.2500
.3125
.3750
.5000
.6250
ROLLER
OUTER DIA.
+.0000
-.0005
.7774
.9014
1.2500
1.4375
1.6875
1.9375
INNER RACE
WIDTH
+.000
-.005
.297
.484
.558
.620
.620
.620
OUTER RACE
WIDTH
+.000
-.005
.270
.335
.375
.469
.500
.500
45 DEG
CHAMFER
+.015
-.000
.005
.005
.015
.015
.015
.015
THRUST
RING
DIA
(REF)
.35
.41
.47
.59
.77
.85
45 DEG
CHAMFER
+.015
-.000
.022
.032
.032
.032
.044
.044
OUTER
RACE
INNER
RACE
THRUST
RING
LINER
DESIGNATION
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
KARON
(SEE TABLE 1 FOR
LINER OPTIONS)
ADD SUFFIX “Z”
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
RADIAL
STATIC
LIMIT
LOAD
(LBS)
See Notes
1&2
AXIAL
STATIC
LIMIT
LOAD
(LBS)
WEIGHT
LBS
(REF)
3410
5860
7640
13425
17680
22100
2035
2490
2940
3768
5200
6200
.04
.07
.14
.23
.31
.38
NOTES:
1. Load ratings shown are based on KAron V liner system.
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
Page 15
Track Rollers, Cam Followers & Airframe Bearings
C
Dimensionally Equivalent to MS27641 Series
W
(2 PL)
KARON
LINER
H
ADD
D
KRP ( )A Series – Self-Lubricating, Narrow
Airframe/Pivot Bearings
"Z" FOR SEAL
E
B
Part Number Example:
KRP 06 A V Z P
OPTION
KRP = KAron Bearing Prefix
–06 = .3750 Bore Diameter (Diameter in 1/16 increments)
A = Narrow Airframe/Pivot Bearing
V = KAron V Liner (See Table 1 for liner Options)
Z = Add “Z” for Seal Option
P = Add “P” for OD Cadmium Plate Option (per QQ-P-416
Type II, Class 2)
A
(2 PL)
For all Sizes:
Radial Play = .0015 to .0035 inches
Axial Play = .005 to .015 inches
LASER OR ELECTRON
BEAM WELD
KRP( ) A
SERIES
BEARING
NUMBER
KRP03A
KRP04A
KRP05A
KRP06A
KRP08A
KRP10A
KRP12A
KRP16A
KRP20A
B
D
W
H
E
A
C
BORE
DIA
+.0000
- .0005
.1900
.2500
.3125
.3750
.5000
.6250
.7500
1.0000
1.2500
ROLLER
OUTER DIA.
+.0000
-.0005
.6250
.7500
.8125
.8750
1.1250
1.3750
1.6250
2.0000
2.2500
INNER RACE
WIDTH
+.000
-.005
.297
.281
.297
.313
.375
.406
.437
.500
.500
OUTER RACE
WIDTH
+.000
-.005
.234
.219
.234
.250
.313
.344
.375
.438
.438
45 DEG
CHAMFER
+.015
-.000
.005
.005
.015
.015
.015
.015
.015
.015
.015
THRUST
RING
DIA
(REF)
.35
.41
.47
.54
.66
.79
.92
1.24
1.48
45 DEG
CHAMFER
+.015
-.000
.016
.016
.016
.016
.016
.032
.032
.032
.032
OUTER
RACE
INNER
RACE
THRUST
RING
LINER
DESIGNATION
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
KARON
(SEE TABLE 1 FOR
LINER OPTIONS)
ADD SUFFIX “Z”
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
RADIAL
STATIC
LIMIT
LOAD
(LBS)
See Notes
1&2
AXIAL
STATIC
LIMIT
LOAD
(LBS)
WEIGHT
LBS
(REF)
2275
2400
3055
4210
7720
11300
14950
24990
29820
2035
2290
2940
3460
4370
5350
6255
8440
10320
.02
.03
.03
.04
.08
.12
.19
.31
.36
NOTES:
1. Load ratings shown are based on KAron V liner system.
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
Page 16
Track Rollers, Cam Followers & Airframe Bearings
W
C
KRP ( )B Series – Self-Lubricating, Narrow
Airframe/Pivot Bearings
Dimensionally Equivalent to MS27642 Series
H
(2 PL)
ADD
"Z" FOR SEAL
OPTION
Part Number Example:
KRP 16 B V Z P
E
KRP = KAron Bearing Prefix
16 = 1.000 Bore Diameter (Diameter in 1/16 increments)
B = Airframe/Pivot Bearing
V = KAron V Liner (See Table 1 for liner Options)
Z = Add “Z” for Seal Option
P = Add “P” for OD Cadmium Plate Option (per QQ-P-416
Type II, Class 2)
(2 PL)
D
A
B
For all Sizes:
Radial Play = .0015 to .0035 inches
Axial Play = .005 to .015 inches
KARON
LINER
LASER OR ELECTRON
BEAM WELD
KRP( ) B
SERIES
BEARING
NUMBER
KRP16B
KRP21B
KRP23B
KRP25B
KRP29B
KRP33B
KRP37B
KRP47B
KRP49B
B
D
W
H
E
A
C
BORE
DIA
+.0000
- .0010
1.0000
1.3130
1.4380
1.5630
1.8130
2.0630
2.3130
2.9380
3.0630
ROLLER
OUTER DIA.
+.0000
-.0010
1.7500
2.0625
2.1875
2.3125
2.5625
2.8125
3.0625
3.8750
4.0000
INNER RACE
WIDTH
+.000
-.005
.437
.437
.437
.437
.437
.437
.437
.531
.531
OUTER RACE
WIDTH
+.000
-.005
.375
.375
.375
.375
.375
.375
.375
.469
.469
45 DEG
CHAMFER
+.015
-.000
.024
.024
.024
.024
.024
.024
.024
.039
.039
THRUST
RING
DIA
(REF)
1.20
1.51
1.64
1.76
2.01
2.26
2.51
3.14
3.26
45 DEG
CHAMFER
+.015
-.000
.024
.024
.024
.024
.024
.024
.024
.039
.039
RADIAL
STATIC
LIMIT
LOAD
(LBS)
See Notes
1&2
AXIAL
STATIC
LIMIT
LOAD
(LBS)
WEIGHT
LBS
(REF)
19500
24540
26650
28600
32665
36725
40790
55110
57215
8290
10625
11605
12510
14395
16280
18160
22910
23815
.18
.23
.24
.26
.29
.33
.36
.73
.75
NOTES:
1. Load ratings shown are based on KAron V liner system.
OUTER
RACE
INNER
RACE
THRUST
RING
LINER
DESIGNATION
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
KARON
(SEE TABLE 1 FOR
LINER OPTIONS)
ADD SUFFIX “Z”
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
Page 17
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
Track Rollers, Cam Followers & Airframe Bearings
KRP( )BS Series – Self-Lubricating, Torque Tube,
Airframe, Pivot Bearings
Dimensionally Equivalent to MS27648 Series
W
C
H
(2 PL)
ADD
RAD
Part Number Example:
KRP 23 BS V Z P
"Z" FOR SEAL
OPTION
KRP = KAron Bearing Prefix
23 = 1.4380 Bore Diameter (Diameter in 1/16 increments)
BS = Self-aligning Torque Tube Bearing
V = KAron V Liner (See Table 1 for liner Options)
Z = Add “Z” for Seal Option
P = Add “P” for OD Cadmium Plate Option (per QQ-P-416
Type II, Class 2)
E
(2 PL)
D
J
A
B
KARON
LINER
For all Sizes:
Radial Play = .0015 to .0035 inches
Axial Play = .005 to .015 inches
LASER OR ELECTRON
BEAM WELD
KRP( )BS
SERIES
BEARING
NUMBER
KRP16BS
KRP21BS
KRP23BS
KRP25BS
KRP29BS
KRP33BS
KRP37BS
KRP47BS
KRP48BS
KRP49BS
B
D
W
H
E
A
C
J
BORE
DIA
+.0000
- .0010
1.0000
1.3130
1.4380
1.5630
1.8130
2.0630
2.3130
2.9380
3.0000
3.0630
ROLLER
OUTER DIA.
+.0000
-.0010
1.9375
2.2500
2.3750
2.5000
2.7500
3.0000
3.2500
4.1250
4.2500
4.2500
INNER RACE
WIDTH
+.000
-.005
.437
.437
.437
.437
.437
.437
.437
.531
.531
.531
OUTER RACE
WIDTH
+.000
-.005
.375
.375
.375
.375
.375
.375
.375
.469
.469
.469
45 DEG
CHAMFER
+.015
-.000
.024
.024
.024
.024
.024
.024
.024
.039
.039
.039
THRUST
RING
DIA
(REF)
1.20
1.51
1.64
1.76
2.01
2.26
2.51
3.14
3.26
3.32
45 DEG
CHAMFER
+.015
-.000
.024
.024
.024
.024
.024
.024
.024
.039
.039
.039
TO
SHARP
CORNER
(REF)
1.710
2.030
2.155
2.282
2.535
2.790
3.040
3.845
3.970
3.970
OUTER
RACE
INNER
RACE
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
OUTER RACE
SELFALIGNING
RING
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
THRUST
RING
LINER
DESIGNATION
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
KARON
(SEE TABLE 1 FOR
LINER OPTIONS)
ADD SUFFIX “Z”
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
Page 18
RADIAL
STATIC
LIMIT
LOAD
(LBS)
See Notes
1&2
AXIAL
STATIC
LIMIT
LOAD
(LBS)
WEIGHT
LBS
(REF)
19500
24540
26650
28600
32665
36725
40970
55110
57215
57215
8290
10625
11605
12510
14395
16280
18160
22910
23815
23815
.22
.27
.29
.32
.35
.40
.43
.88
.91
.91
NOTES:
1. Load ratings shown are based on KAron V liner system.
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
Track Rollers, Cam Followers & Airframe Bearings
W
C
(2 PL)
Dimensionally Equivalent to MS27644 Series
H
KARON
LINER
ADD
D
KRP ( )P Series – KAron Lined, Self-Lubricating,
Wide Airframe/Pivot Bearings
E
B
(2 PL)
Part Number Example:
KRP 06 P V Z P
"Z" FOR SEAL
OPTION
KRP = KAron Bearing Prefix
–06 = .3750 Bore Diameter (Diameter in 1/16 increments)
P = Wide Airframe/Pivot Bearing
V = KAron V Liner (See Table 1 for liner Options)
Z = Add “Z” for Seal Option
P = Add “P” for OD Cadmium Plate Option (per QQ-P-416
Type II, Class 2)
A
(2 PL)
For all Sizes:
Radial Play = .0015 to .0035 inches
Axial Play = .005 to .015 inches
LASER OR ELECTRON
BEAM WELD
KRP( ) P
SERIES
BEARING
NUMBER
KRP03P
KRP04P
KRP05P
KRP06P
KRP08P
KRP10P
B
D
W
H
E
A
C
BORE
DIA
+.0000
- .0005
.1900
.2500
.3125
.3750
.5000
.6250
ROLLER
OUTER DIA.
+.0000
-.0005
.7774
.9014
1.2500
1.4375
1.6875
1.9375
INNER RACE
WIDTH
+.000
-.005
.495
.620
.745
.870
.932
.995
OUTER RACE
WIDTH
+.000
-.005
.473
.491
.687
.794
.856
.920
45 DEG
CHAMFER
+.015
-.000
.005
.005
.015
.015
.015
.015
THRUST
RING
DIA
(REF)
.350
.410
.500
.625
.735
.890
45 DEG
CHAMFER
+.015
-.000
.018
.032
.032
.032
.044
.044
OUTER
RACE
INNER
RACE
THRUST
RING
LINER
DESIGNATION
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
KARON
(SEE TABLE 1 FOR
LINER OPTIONS)
ADD SUFFIX “Z”
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
Page 19
RADIAL
STATIC
LIMIT
LOAD
(LBS)
See Notes
1&2
AXIAL
STATIC
LIMIT
LOAD
(LBS)
WEIGHT
LBS
(REF)
6825
9330
16380
26800
42250
58500
2025
2500
3240
3770
4675
5650
.06
.09
.24
.35
.55
.75
NOTES:
1. Load ratings shown are based on KAron V liner system.
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
Track Rollers, Cam Followers & Airframe Bearings
KRPB500 Series – Self-Lubricating, Narrow
Airframe, Pivot Bearings
Dimensionally Equivalent to MS27646 Series
W
C
H
(2 PL)
ADD
"Z" FOR SEAL
OPTION
Part Number Example:
KRPB 540 V Z P
E
(2 PL)
D
KRPB = KAron Bearing Prefix
540 = .875 Bore Diameter (Diameter in 1/16 increments)
V = KAron V Liner (See Table 1 for liner Options)
Z = Add “Z” for Seal Option
P = Add “P” for OD Cadmium Plate Option (per QQ-P-416
Type II, Class 2)
A
B
KARON
LINER
For all Sizes:
Radial Play = .0015 to .0035 inches
Axial Play = .005 to .015 inches
LASER OR ELECTRON
BEAM WELD
KRPB500
SERIES
BEARING
NUMBER
KRPB538
KRPB539
KRPB540
KRPB541
KRPB542
KRPB543
KRPB544
KRPB545
KRPB546
B
D
W
H
E
A
C
BORE
DIA
+.0007
- .0007
.6250
.7500
.8750
1.0625
1.3125
1.5625
1.8135/1.8115
2.0635/2.0615
2.3135/2.3115
ROLLER
OUTER DIA.
+.0000
-.0010
1.0625
1.1875
1.3125
1.5000
1.7500
2.0000
2.2500/2.2485
2.6250/2.6235
2.8750/2.8735
INNER RACE
WIDTH
+.000
-.005
.281
.281
.281
.281
.281
.281
.281
.281
.281
OUTER RACE
WIDTH
+.000
-.005
.250
.250
.250
.250
.250
.250
.250
.250
.250
45 DEG
CHAMFER
+.020
-.000
.015
.015
.015
.015
.015
.015
.015
.015
.015
THRUST
RING
DIA
(REF)
.80
.91
1.04
1.22
1.47
1.72
1.97
2.28
2.55
45 DEG
CHAMFER
+.020
-.000
.015
.015
.015
.015
.015
.015
.015
.015
.015
OUTER
RACE
INNER
RACE
THRUST
RING
LINER
DESIGNATION
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
KARON
(SEE TABLE 1 FOR
LINER OPTIONS)
ADD SUFFIX “Z”
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
RADIAL
STATIC
LIMIT
LOAD
(LBS)
See Notes
1&2
AXIAL
STATIC
LIMIT
LOAD
(LBS)
WEIGHT
LBS
(REF)
6240
7020
8110
9515
11460
13415
15360
17940
19890
5275
6030
7235
8590
10475
12360
14240
16425
18310
.04
.05
.06
.07
.08
.09
.10
.16
.17
NOTES:
1. Load ratings shown are based on KAron V liner system.
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
Page 20
Track Rollers, Cam Followers & Airframe Bearings
KRP 562 Series – Studded, Self-Lubricating,
Track Roller, Cam Follower Bearings
Dimensionally Equivalent to NAS 562 Series
STUD LENGTH
SEE NOTE 1
KARON
LINER
GRIP LENGTH
+,-0.406
H
SEALS
M
L
KRP 562– 6 V T
"Z" FOR SEAL
ADD
0.406
REF
Part Number Example:
OPTION
G
D
F
A
B
THREAD LENGTH
S 2 INCOMPLETE
T
THREADS MAX
2.54 MIN
SCREW DRIVER SLOT
OR HEX HOLE
K – 16 S
D
KRP = KAron Track Roller Bearing Prefix
562 = Studded Roller Series, Crowned Outer Race
–6 = 9.525 Stud Diameter (Diameter in 1/16 inch increments)
V = KAron V Liner (See Table 1 for liner Options)
T = Track Roller Designation (not optional in p/n)
Z = Add “Z” for Seal Option
A = Add “A” for NO Cotter Pin Hole
K = Add “K” for Keyway Option
–16 = 25.400 mm Stud Grip Length (Length in 1/16 inch Increments)
S = Add “S” for PH13-8MO CRES Stud Option.
D = Add “D” for 440C Outer Race Option
N
P
Z A
For all Sizes:
Radial Play = 0.038 to 0.089 mm
Axial Play = 0.130 to 0.381 mm
METRIC
All Dimensions in Millimeters
KRP562
SERIES
BEARING
NUMBER
KRP562-3
KRP562-4
KRP562-5
KRP562-6
KRP562-7
KRP562-8
B
STUD
DIA
+.000
- .025
4.826
6.350
7.925
9.525
11.100
12.700
D
ROLLER
OUTER
DIA.
+.025
-.013
12.700
17.463
19.050
22.225
25.400
28.575
STANDARD
OUTER
STUD &
RACE
THRUST RING
AMS 5617
CUSTOM
455
Rc 47 MIN
H
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
ROLLER
WIDTH
+.127
-.127
7.137
7.137
8.738
11.913
13.487
16.662
DIST TO
COTTER
PIN
HOLE
1900-32
.2500-28
.3125-24
.3750-24
.4375-20
.5000-20
5.359
5.690
5.944
6.731
7.188
7.976
S
L
M
N
G
P
T
A
THREAD
LENGTH
(REF)
KEYWAY
LENGTH
+.762
-.000
N/A
8.560
8.306
10.566
11.481
13.081
KEYWAY
RUNOUT
(REF)
KEY
WIDTH
+.051
-.051
N/A
1.613
1.613
2.405
2.405
3.200
SLOT
DEPTH
+.254
-.254
N/A
5.443
6.955
8.219
9.807
10.998
HOLE
DIA
+.254
-.000
1.778
1.930
1.930
2.692
2.692
2.692
TRACK
CONTACT
WIDTH
MIN
5.842
5.842
7.366
9.652
10.922
13.462
RING
DIA
(REF)
MIN
LINER
KARON
(SEE TABLE
1 FOR
LINER
OPTIONS)
F
THREAD
SIZE
UNJF-3A
PER
MIL-S-8879
(inches)
8.738
8.738
9.119
9.119
10.719
10.719
SUFFIX DESIGNATION
ADD SUFFIX
ADD SUFFIX
S
D
Z
TO P/N FOR AMS 5629
(PH13-8MO)
Rc 43 MIN (COND
H1000 REF), STUD &
THRUST RING
TO P/N FOR
AMS 5630
(440C) Rc 55-62
OUTER RACE
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
Page 21
ADD SUFFIX
N/A
11.100
11.100
12.700
14.275
15.875
10.16
14.48
14.99
18.29
21.34
24.64
NOTES:
1. Stud Length = Nominal Grip Length + “S” Thread
Length, +0.787, -0.406
2. Load ratings shown are based on KAron V liner
system.
3. Loads shown are based on bearing components only,
stud bending not considered.
RADIAL
STATIC
LIMIT
LOAD
(KN)
See Notes
2&3
13.0
16.1
23.5
44.5
59.3
81.0
Track Rollers, Cam Followers & Airframe Bearings
STUD LENGTH
SEE NOTE 1
KARON
LINER
SLOT OR
HEX HOLE
KRP 567 Series – Studded, Self-Lubricating
Crowned Outer Race, Track Roller, Cam
Follower Bearings
Otherwise Dimensionally Equivalent to KRP 562 Series
GRIP LENGTH
+,-.406
H
ADD
.406
REF
Part Number Example:
SEALS
M
L
KRP 567– 6 V T
"Z" FOR SEAL
N
G
D
F
A
B
THREAD LENGTH
S 2 INCOMPLETE
C CROWN
THREADS MAX
2.54 MIN
RAD
K – 16 S
D
KRP = KAron Track Roller Bearing Prefix
567 = Studded Roller Series, Crowned Outer Race
–6 = 9.525 mm Stud Diameter (Diameter in 1/16 inch increments)
V = KAron V Liner (See Table 1 for liner Options)
T = Track Roller Designation (not optional in p/n)
Z = Add “Z” for Seal Option
A = Add “A” for NO Cotter Pin Hole Option
K = Add “K” for Keyway Option
–16 = 25.400 mm Stud Grip Length (Length in 1/16 inch Increments)
S = Add “S” for PH13-8MO CRES Stud Option.
D = Add “D” for 440C CRES Outer Race Option
OPTION
P
Z A
For all Sizes:
Radial Play = 0.038 to 0.089 mm
Axial Play = 0.130 to 0.381 mm
METRIC
All Dimensions in Millimeters
KRP567
SERIES
BEARING
NUMBER
KRP567-3
KRP567-4
KRP567-5
KRP567-6
KRP567-7
KRP567-8
B
STUD
DIA
+.000
- .025
4.826
6.350
7.925
9.525
11.100
12.700
D
ROLLER
OUTER
DIA.
+.025
-.013
12.700
17.463
19.050
22.225
25.400
28.575
STANDARD
OUTER
STUD &
RACE
THRUST RING
AMS 5617
CUSTOM
455
Rc 47 MIN
H
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
ROLLER
WIDTH
+.127
-.127
7.137
7.137
8.738
11.913
13.487
16.662
F
THREAD
SIZE
UNJF-3A
PER
MIL-S-8879
(INCHES)
DIST TO
COTTER
PIN
HOLE
1900-32
.2500-28
.3125-24
.3750-24
.4375-20
.5000-20
5.359
5.690
5.944
6.731
7.188
7.976
L
M
N
G
P
C
A
THREAD
LENGTH
(REF)
KEYWAY
LENGTH
+.762
-.000
N/A
8.560
8.306
10.566
11.481
13.081
KEYWAY
RUNOUT
(REF)
KEY
WIDTH
+.051
-.051
N/A
1.613
1.613
2.405
2.405
3.200
SLOT
DEPTH
+.254
-.254
N/A
5.443
6.955
8.219
9.807
10.998
HOLE
DIA
+.254
-.000
1.778
1.930
1.930
2.692
2.692
2.692
CROWN
RADIUS
(REF)
RING
DIA
(REF)
152
152
178
203
254
305
10.16
14.48
14.99
18.29
21.34
24.64
MIN
LINER
KARON
(SEE TABLE
1 FOR
LINER
OPTIONS)
S
8.738
8.738
9.119
9.119
10.719
10.719
N/A
11.100
11.100
12.700
14.275
15.875
SUFFIX DESIGNATION
ADD SUFFIX
ADD SUFFIX
S
D
Z
TO P/N FOR AMS 5629
(PH13-8MO)
Rc 43 MIN (COND
H1000 REF), STUD &
THRUST RING
TO P/N FOR
AMS 5630
(440C) Rc 55-62
OUTER RACE
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
Page 22
ADD SUFFIX
RADIAL
STATIC
LIMIT
LOAD
(KN)
See Notes
2&3
13.0
16.1
23.5
44.5
59.3
81.0
NOTES:
1. Stud Length = Nominal Grip Length + “S” Thread
Length, +0.787, -0.406
2. Load ratings shown are based on KAron V liner
system.
3. Loads shown are based on bearing components only,
stud bending not considered.
KRP 502 Series – KAron Lined, Self-Lubricating,
Track Roller, Cam Follower
Track Rollers, Cam Followers & Airframe Bearings
W
H
KARON
LINER
D
Dimensionally Equivalent to MS24465 Series
ADD
E
B
Part Number Example:
KRP 502– 06 V T Z
"Z" FOR SEAL
OPTION
KRP = KAron Track Roller Bearing Prefix
502 = Non-Studded Roller Series
–06 = 9.525 mm Bore Diameter (Diameter in 1/16 inch increments)
V = KAron V Liner (See Table 1 for liner Options)
T = Track Roller Designation (not optional in p/n)
Z = Add “Z” for Seal Option
D = Add “D” for 440C Outer Race Option
A
For all Sizes:
Radial Play = 0.038 to 0.089 mm
Axial Play = 0.130 to 0.381 mm
LASER OR ELECTRON
BEAM WELD
METRIC
All Dimensions in Millimeters
T
KRP502
SERIES
BEARING
NUMBER
KRP502-03
KRP502-04
KRP502-06
KRP502-08
KRP502-10
KRP502-12
KRP502-14
OUTER
RACE
AMS 5617
CUSTOM 455
Rc 47 MIN
D
B
D
W
H
E
BORE
DIA
+.000
- .013
4.826
6.350
9.525
12.700
15.875/15.857
19.050/19.032
22.225/22.207
ROLLER
OUTER
DIA.
+.000
-.025
19.050
22.225
26.988
33.338
38.100
44.450
50.800
INNER
RACE
WIDTH
+.000
-.127
7.925
9.525
12.700
15.875
19.050
25.400
28.575
OUTER
RACE
WIDTH
+.000
-.127
5.537
7.137
9.525
12.700
15.875
22.225
25.400
RADIUS OR
45 DEG
CHAMFER
TO CLEAR
FILLET RAD
0.559
0.559
0.559
0.813
0.813
0.813
0.813
INNER
RACE
THRUST
RING
LINER
DESIGNATION
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
KARON
(SEE TABLE 1
ADD SUFFIX
Z
D
FOR
LINER
OPTIONS)
TO P/N FOR
SEAL OPTION
(ACETAL
RESIN
OR NYLON)
TO PART NUMBER
FOR
440C OUTER RACE
AMS 5630 Rc 55-62
Page 23
ADD SUFFIX
A
T
THRUST
RING
DIA
(REF)
16.00
17.27
23.88
28.45
31.75
38.10
41.15
TRACK
CONTACT
WIDTH
MIN
3.175
5.537
7.925
11.125
14.275
19.050
22.225
RADIAL
STATIC
LIMIT
LOAD
(KN)
See Notes
1&2
AXIAL
STATIC
LIMIT
KN
(LBS)
WEIGHT
LBS
(KG)
18.2
29.6
53.1
93.1
132.0
231.3
341.2
9.1
11.1
15.4
20.1
24.5
29.2
34.5
0.014
0.027
0.045
0.086
0.136
0.249
0.385
NOTES:
1. Load ratings shown are based on KAron V liner
system.
2. Loads shown are based on bearing components
only, bolt/pin shear not considered.
Track Rollers, Cam Followers & Airframe Bearings
KRP 503 Series – Self-Lubricating, Airframe, Pivot
& Track Roller Bearings
Dimensionally Equivalent to MS24466 Series
W
KARON
LINER
D
H
ADD
E
B
Part Number Example:
KRP 503– 06 V T Z
"Z" FOR SEAL
OPTION
D
KRP = KAron Track Roller Bearing Prefix
503 = Non-Studded Roller Series
–06 = 9.525 mm Bore Diameter (Diameter in 1/16 inch increments)
V = KAron V Liner (See Table 1 for liner Options)
T = Track Roller Designation (not optional in p/n)
Z = Add “Z” for Seal Option
D = Add “D” for 440C Outer Race Option
A
For all Sizes:
Radial Play = 0.038 to 0.089 mm
Axial Play = 0.130 to 0.381 mm
LASER OR ELECTRON
BEAM WELD
METRIC
All Dimensions in Millimeters
T
KRP503
SERIES
BEARING
NUMBER
KRP503-06
KRP503-08
KRP503-10
KRP503-12
KRP503-14
OUTER
RACE
AMS 5617
CUSTOM 455
Rc 47 MIN
B
D
W
H
E
BORE
DIA
+.000
- .013
9.525
12.700
15.875/15.857
19.050/19.032
22.225/22.207
ROLLER
OUTER
DIA.
+.000
-.025
28.575
34.925
41.275
47.625
53.975
INNER
RACE
WIDTH
+.000
-.127
25.400
31.750
38.100
44.450
50.800
OUTER
RACE
WIDTH
+.000
-.127
22.225
28.575
34.925
41.275
47.625
RADIUS OR
45 DEG
CHAMFER
TO CLEAR
FILLET RAD
0.559
0.813
0.813
0.813
0.813
T
THRUST
RING
DIA
(REF)
23.88
28.45
33.78
40.13
43.69
TRACK
CONTACT
WIDTH
MIN
19.050
25.400
28.575
34.925
41.275
RADIAL
STATIC
LIMIT
LOAD
(KN)
See Notes
1&2
AXIAL
STATIC
LIMIT
LOAD
(KN)
WEIGHT
LBS
(KG)
134.2
216.9
336.1
455.4
629.2
16.1
20.8
25.1
29.5
33.5
0.113
0.204
0.336
0.517
0.748
NOTES:
1. Load ratings shown are based on KAron V liner system.
INNER
RACE
THRUST
RING
LINER
DESIGNATION
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
KARON
(SEE TABLE 1
ADD SUFFIX
ADD SUFFIX
Z
D
FOR
LINER
OPTIONS)
TO P/N FOR
SEAL OPTION
(ACETAL
RESIN
OR NYLON)
TO PART NUMBER
FOR
440C OUTER RACE
AMS 5630 Rc 55-62
Page 24
A
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
KRP 522 Series – Track Roller,
Crowned Outer Race
Track Rollers, Cam Followers & Airframe Bearings
W
H
KARON
LINER
D
Similar to KRP 502 Series with Crowned Outer Race
ADD
E
B
(2 PL)
"Z" FOR SEAL
Part Number Example:
KRP 522– 06 V T Z
OPTION
KRP = KAron Bearing Prefix
522 = Crowned Track Roller Series
–06 = 9.525 mm Bore Diameter (Diameter in 1/16 inch increments)
V = KAron V Liner (See Table 1 for liner Options)
T = Add “T” for Track Roller (not optional in P/N)
Z = Add “Z” for Seal Option
D = Add “D” for 440C Outer Race Option
A (2 PL)
LASER OR ELECTRON
BEAM WELD
Cr
KRP522
SERIES
BEARING
NUMBER
KRP522-03
KRP522-04
KRP522-06
KRP522-08
KRP522-10
KRP522-12
KRP522-14
KRP522-16
KRP522-20
KRP522-24
KRP522-28
KRP522-32
KRP522-36
KRP522-40
KRP522-44
METRIC
All Dimensions in Millimeters
R (2 PL)
T
D
B
D
W
H
BORE
DIA
+.000
- .018
4.826
6.350
9.525
12.700
15.875
19.050
22.225
25.400
31.750
38.100
44.450
50.800
57.150
63.500
69.850
ROLLER
OUTER
DIA.
+.000
-.025
19.050
22.225
25.464
33.338
38.100
44.450
50.800
53.975
57.150
76.225/76.170
87.338/87.282
98.450/98.395
109.563/109.507
120.675/120.620
127.025/126.970
INNER
RACE
WIDTH
+.000
-.254
7.925
9.525
12.700
15.875
19.050
25.400
28.575
30.150
31.750
38.100
38.100
38.100
38.100
38.100
38.100
OUTER
RACE
WIDTH
+.000
-.381
7.112
8.763
11.557
14.732
17.907
24.130
27.305
31.750
36.576
36.576
36.576
36.576
36.576
36.576
36.576
OUTER
RACE
INNER
RACE
THRUST
RING
LINER
AMS 5617
CUSTOM
455
Rc 47 MIN
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
KARON
(SEE TABLE 1
FOR
LINER
OPTIONS)
E
45 DEG
CHAMFER
+.254
-.000
0.559
0.559
0.559
0.813
0.813
0.813
0.813
0.813
0.813
0.813
0.813
0.813
0.813
0.813
0.813
DESIGNATION
ADD SUFFIX “Z”
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
ADD SUFFIX “D”
TO PART NUMBER
FOR
440C OUTER RACE
AMS 5630 Rc 55-62
Page 25
A
THRUST
RING
DIA
(REF)
11.18
13.21
17.02
21.34
24.13
28.19
30.99
41.40
44.45
50.80
57.91
65.02
72.64
78.99
84.84
R
CORNER
RADIUS
+.254
-.000
0.56
0.56
0.56
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
CROWN
RADIUS
(REF)
RADIAL
STATIC
LIMIT
LOAD
(KN)
See Notes
1&2
WEIGHT
KG
(REF)
254
254
254
317.5
444.5
635
698.5
762
762
1524
1524
1524
1524
1524
1524
21.3
34.2
57.8
102.2
155.6
233.3
296.4
366.2
462.2
644.4
726.7
806.7
920.0
1006.7
1048.9
0.01
0.03
0.05
0.09
0.14
0.25
0.39
0.59
0.80
1.00
1.32
1.64
2.05
2.45
2.55
Cr
NOTES:
1. Load ratings shown are based on KAron V liner system.
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
3. For all Sizes:
Radial Play = 0.038 to 0.089 mm
Axial Play = 0.130 to 0.381 mm
Track Rollers, Cam Followers & Airframe Bearings
KRP 523 Series – Self-Lubricating, Airframe,
Pivot & Track Roller Bearings
Typical Aircraft High Load Flap Track Roller Series
W
KARON
LINER
D
H
ADD
E
B
Part Number Example:
KRP 523– 06 V T Z
"Z" FOR SEAL
OPTION
KRP = KAron Track Roller Bearing Prefix
523 = Non-Studded Roller Series
–06 = 9.525 mm Bore Diameter (Diameter in 1/16 inch increments)
V = KAron V Liner (See Table 1 for liner Options)
T = Track Roller Designation (not optional in p/n)
Z = Add “Z” for Seal Option
D = Add “D” for 440C Outer Race Option
A
LASER OR ELECTRON
BEAM WELD
T
KRP503
SERIES
BEARING
NUMBER
KRP523-04
KRP523-06
KRP523-08
KRP523-10
KRP523-12
KRP523-14
KRP523-16
KRP523-20
KRP523-24
KRP523-28
KRP523-32
D
For all Sizes:
Radial Play = 0.038 to 0.089 mm
Axial Play = 0.130 to 0.381 mm
METRIC
All Dimensions in Millimeters
B
D
W
H
E
BORE
DIA
ROLLER
OUTER
DIA.
INNER
RACE
WIDTH
OUTER
RACE
WIDTH
RADIUS OR
45 DEG
CHAMFER
+.000
- .013
6.350
9.525
12.700
15.875
19.050
22.225
25.400
31.750
38.100
44.450
50.800
+.000
-.025
22.225
28.575
34.925
41.275
47.625
53.975
60.325
69.850
76.225/76.170
87.338/87.282
98.450/98.395
+.000
-.127
19.050
25.400
31.750
38.100
44.450
50.800
57.150
63.500
69.850
76.200
76.200
+.000
-.127
18.034
23.876
30.226
36.576
42.926
49.276
55.626
61.976
68.326
74.676
74.676
+.254
-.000
0.559
0.559
0.813
0.813
0.813
0.813
0.813
0.813
0.813
0.813
0.813
OUTER
RACE
INNER
RACE
THRUST
RING
LINER
AMS 5617
CUSTOM 455
Rc 47 MIN
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
KARON
(SEE TABLE 1
FOR
LINER
OPTIONS)
DESIGNATION
ADD SUFFIX
Z
TO P/N FOR
SEAL OPTION
(ACETAL
RESIN
OR NYLON)
ADD SUFFIX
D
TO PART NUMBER
FOR
440C OUTER RACE
AMS 5630 Rc 55-62
Page 26
A
T
TRACK
CONTACT
WIDTH
MIN
RADIAL
STATIC
LIMIT
LOAD
(KN)
See Notes
1&2
THRUST
RING
DIA
(REF)
WEIGHT
KG
(REF)
13.21
17.02
21.34
24.13
28.19
30.99
40.13
41.40
50.80
57.91
65.02
14.73
19.05
25.40
28.70
35.05
41.40
47.75
51.56
57.91
66.80
66.80
73.4
129.0
222.4
338.1
435.9
564.9
769.6
992.0
1258.9
1556.9
1726.0
0.054
0.113
0.204
0.336
0.517
0.748
1.043
1.497
1.859
2.630
3.311
NOTES:
1. Load ratings shown are based on KAron V liner system.
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
Track Rollers, Cam Followers & Airframe Bearings
W
KARON
LINER
KRP 527 Series – KAron Lined, Self-Aligning, SelfLubricating, Track Roller/ Cam Follower Series
"O" RING SNUBBER
OPTION (BOTH SIDES)
H
SEAL/SNUBBER
(BOTH SIDES)
Part Number Example:
KRP 527 08 V T
KRP = KAron Bearing Prefix
527 = Self-Aligning Roller Series
–08 = 12.700 mm Bore Diameter (Diameter in 1/16 inch increments)
V = KAron V Liner (See Table 1 for liner Options)
T = Track Roller Application
B
D
S
(2 PL)
2 DEGREE MIN.
MISALIGNMENT
For all Sizes:
Radial Play = 0.076 mm maximum
Rotational Torque (no-load) = 0.23 N-m maximum
E(2 PL)
C
(2 PL)
A
ELECTRON
BEAM WELD
INSERT
METRIC
All Dimensions in Millimeters
KRP527
SERIES
BEARING
NUMBER
KRP527-04
KRP527-06
KRP527-08
KRP527-10
KRP527-12
KRP527-14
OUTER RACE
& INSERT
AMS 5617
CUSTOM 455
Rc 47 MIN
B
D
W
H
E
A
BORE
DIA
+.000
- .018
6.350
9.525
12.700
15.875
19.050
22.225
ROLLER
OUTER DIA.
+.000
-.025
22.225
28.575
34.925
41.275
47.625
53.975
INNER RACE
WIDTH
+.000
-.254
19.050
25.400
31.750
38.100
44.450
50.800
OUTER RACE
WIDTH
+.000
-.254
16.662
23.876
30.226
36.576
42.926
49.276
45 DEG
CHAMFER
+.254
-.000
0.56
0.56
0.81
0.81
0.81
0.81
INNER
RACE
SPHERICAL
DIA
(REF)
15.49
20.32
24.59
30.48
34.93
41.15
INNER RACE
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
SEAL / SNUBBER
LINER
KARON
PTFE / ELASTOMER
(SEE TABLE 1 FOR
LINER OPTIONS)
C
S
CORNER
RADIUS
(MINIMUM)
CLAMP-UP
DIAMETER
(REF)
0.51
1.02
1.27
1.27
1.27
1.27
13.21
17.02
21.34
23.11
28.19
30.99
NOTES:
1. Load ratings shown are based on KAron V liner system.
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
Page 27
RADIAL
STATIC
LIMIT
LOAD
(KN)
See Notes
1&2
WEIGHT
KG
(REF)
56.0
89.4
122.3
218.0
233.1
317.2
0.054
0.113
0.204
0.336
0.517
0.748
Track Rollers, Cam Followers & Airframe Bearings
R
Dimensionally Equivalent to MS24461 Series
W
(2 PL)
KARON
LINER
D
KRP 505 Series – Self-Lubricating Airframe, Pivot
& Track Roller Bearings
H
ADD
B
E
Part Number Example:
KRP 505– 06 V T Z
"Z" FOR SEAL
OPTION
(2 PL)
KRP505
SERIES
METRIC
All Dimensions in
Millimeters
BEARING
NUMBER
KRP505-03
KRP505-04
KRP505-05
KRP505-06
KRP505-07
KRP505-08
KRP505-09
KRP505-10
KRP505-12
KRP505-14
KRP505-16
KRP505-20
KRP505-24
KRP505-28
KRP505-32
KRP505-36
KRP505-40
KRP505-44
KRP505-48
KRP505-52
B
D
W
H
E
BORE
DIA
+.000
- .013
4.826
6.350
7.938
9.525
11.113
12.700
14.288
14.270
15.875
15.857
19.050
19.032
22.225
22.207
25.400
25.382
31.750
31.732
38.100
38.082
44.450
44.432
50.800
50.782
57.150
57.132
63.500
63.482
69.850
69.832
76.200
76.182
82.550
82.530
ROLLER
OUTER
DIA.
+.000
-.013
17.463
19.050
20.638
22.225
23.813
28.575
30.163
31.750
34.925
41.275
44.450
50.800
50.785
57.150
57.135
63.500
63.485
69.850
69.835
76.200
76.185
82.550
82.530
88.900
88.880
95.250
95.230
101.600
101.580
INNER
RACE
WIDTH
+.000
-.127
7.925
9.525
11.100
14.275
15.875
19.050
22.225
25.400
28.575
31.750
31.750
31.750
31.750
31.750
31.750
31.750
31.750
31.750
31.750
31.750
OUTER
RACE
WIDTH
+.000
-.127
5.537
7.137
8.738
11.913
13.487
16.662
19.837
23.012
25.400
28.575
28.575
26.645
26.645
26.645
26.645
26.645
26.645
26.645
26.645
26.645
RADIUS OR
45 DEG
CHAMFER
TO CLEAR
FILLET RAD
0.559
0.559
0.559
0.559
0.813
0.813
0.813
0.813
0.813
0.813
0.813
0.813
0.813
0.813
0.813
0.813
0.813
0.813
0.813
0.813
OUTER
RACE
INNER
RACE
THRUST
RING
LINER
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
KARON
(SEE TABLE 1
FOR
LINER
OPTIONS)
A
R
THRUST
RING
DIA
(REF)
13.46
15.49
16.26
18.29
19.81
24.64
26.16
27.69
30.99
37.34
39.37
45.72
52.07
58.42
64.77
71.12
77.47
83.82
90.17
96.52
RADIUS OR
45 DEG
CHAMFER
+.25
-.000
0.56
0.56
0.56
0.56
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
DESIGNATION
ADD SUFFIX “Z”
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
ADD SUFFIX “T” FOR
TRACK ROLLER OPTION
AMS 5617 OUTER RACE
CUSTOM 455 Rc 47 MIN
Rev D May 5, 2004 : KRP505-()VT OPTION WAS 440C
Page 28
P
KRP = KAron Bearing Prefix
505 = Airframe/Pivot/Roller Series
–06 = 9.525 mm ID (Diameter in 1/16 inch increments)
V = KAron V Liner (See Table 1 for liner Options)
T = Add “T” for Track Roller (Custom 455 Outer Race) Option
Z = Add “Z” for Seal Option
D = Add “D” for 440C Outer Race Option
P = Add “P” for OD Cadmium Plate Option (per QQ-P-416 Type II, Class 2)
A
LASER OR ELECTRON
BEAM WELD
D
ADD SUFFIX “D”
TO PART NUMBER
FOR
440C OUTER RACE
AMS 5630 Rc 55 -62
RADIAL
STATIC
LIMIT
LOAD
(KN)
See Notes
1&2
AXIAL
STATIC
LIMIT
LOAD
(KN)
WEIGHT
KG
(REF)
18.0
29.6
40.8
68.7
88.5
127.5
158.2
189.7
252.7
327.9
379.5
455.4
531.3
607.2
683.1
759.0
834.9
910.8
987.2
1062.6
9.1
11.1
13.1
15.4
17.4
20.1
22.1
24.1
28.5
32.9
37.5
45.9
54.3
62.9
71.1
79.6
87.8
96.2
104.6
113.3
0.014
0.018
0.023
0.032
0.041
0.077
0.100
0.122
0.154
0.240
0.263
0.313
0.358
0.408
0.454
0.503
0.553
0.603
0.649
0.680
NOTES:
1. Load ratings shown are based on KAron V liner system.
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
3. For all Sizes:
Radial Play = 0.038 to 0.089 mm
Axial Play = 0.127 to 0.381 mm
Track Rollers, Cam Followers & Airframe Bearings
R
Dimensionally Equivalent to MS24462 Series
W
(2 PL)
KARON
LINER
D
KRP 506 Series –Self-Lubricating, Airframe, Pivot
& Track Roller Bearings
H
ADD
B
E
Part Number Example:
KRP 506– 06 V T Z
"Z" FOR SEAL
OPTION
A
LASER OR ELECTRON
BEAM WELD
BEARING
NUMBER
KRP506-03
KRP506-04
KRP506-05
KRP506-06
KRP506-07
KRP506-08
KRP506-10
KRP506-12
KRP506-14
KRP506-16
KRP506-20
METRIC
All Dimensions in
Millimeters
B
D
W
H
E
BORE
DIA
+.000
- .013
4.826
6.350
7.938
9.525
11.113
12.700
15.875
19.050
22.225
25.400
31.750
ROLLER
OUTER
DIA.
+.000
-.025
15.875
15.875
17.463
19.050
20.638
25.400
28.575
31.750
34.925
38.100
47.625
INNER
RACE
WIDTH
+.000
-.127
15.875
14.275
15.875
20.625
22.225
22.225
22.225
28.575
28.575
28.575
34.925
OUTER
RACE
WIDTH
+.000
-.127
12.700
12.700
12.700
19.050
19.050
19.050
19.050
25.400
25.400
25.400
31.750
RADIUS OR
45 DEG
CHAMFER
TO CLEAR
FILLET RAD
0.559
0.559
0.559
0.559
0.559
0.813
0.813
0.813
0.813
0.813
0.813
OUTER
RACE
INNER
RACE
THRUST
RING
LINER
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
KARON
(SEE TABLE 1
FOR
LINER
OPTIONS)
P
KRP = KAron Bearing Prefix
506 = Airframe/Pivot/Roller Series
–06 = 9.525 mm ID (Diameter in 1/16 inch increments)
V = KAron V Liner (See Table 1 for liner Options)
T = Add “T” for Track Roller (Custom 455 Outer Race) Option
Z = Add “Z” for Seal Option
D = Add “D” for 440C Outer Race Option
P = Add “P” for OD Cadmium Plate Option (per QQ-P-416
Type II, Class 2)
(2 PL)
KRP506
SERIES
D
For all Sizes:
Radial Play = 0.038 to 0.089 mm
Axial Play = 0.127 to 0.381 mm
A
R
THRUST
RING
DIA
(REF)
12.95
12.95
14.48
16.00
17.53
22.35
25.40
28.45
31.75
35.05
44.45
RADIUS OR
45 DEG
CHAMFER
+.254
-.000
0.56
0.56
0.56
0.56
0.56
0.81
0.81
0.81
0.81
0.81
0.81
ADD SUFFIX “T” FOR
TRACK ROLLER OPTION
AMS 5617 OUTER RACE
CUSTOM 455 Rc 47 MIN
Rev D May 5, 2004 : KRP506-()VT OPTION WAS 440C
Rev G Dec 23, 2008: MS24462 was MS24461
Page 29
AXIAL
STATIC
LIMIT
LOAD
(KN)
WEIGHT
KG
(REF)
51.6
47.1
63.4
99.8
116.6
137.4
164.5
216.5
252.6
323.7
497.4
9.1
10.4
12.4
14.7
16.4
19.4
23.8
27.8
32.2
36.2
44.6
0.023
0.018
0.027
0.036
0.041
0.063
0.073
0.113
0.127
0.141
0.277
NOTES:
1. Load ratings shown are based on
KAron V liner system.
DESIGNATION
ADD SUFFIX “Z”
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
RADIAL
STATIC
LIMIT
LOAD
(KN)
See Notes
1&2
ADD SUFFIX “D”
TO PART NUMBER
FOR
440C OUTER RACE
AMS 5630 Rc 55-62
2. Loads shown are based on
bearing components only, bolt/pin
shear is not considered.
Track Rollers, Cam Followers & Airframe Bearings
C
Dimensionally Equivalent to MS27640 Series
W
(2 PL)
KARON
LINER
H
ADD
D
KRP ( ) Series – Self-Lubricating Airframe/Pivot
Bearings
"Z" FOR SEAL
E
B
Part Number Example:
KRP 06 V Z P
OPTION
KRP = KAron Bearing Prefix
–06 = 9.525 mm ID (Diameter in 1/16 inches increments)
V = KAron V Liner (See Table 1 for liner Options)
Z = Add “Z” for Seal Option
P = Add “P” for OD Cadmium Plate Option (per QQ-P-416
Type II, Class 2)
A
For all Sizes:
Radial Play = 0.038 to 0.089 mm
Axial Play = 0.127 to 0.381 mm
(2 PL)
LASER OR ELECTRON
BEAM WELD
KRP( )
SERIES
BEARING
NUMBER
KRP03
KRP04
KRP05
KRP06
KRP08
KRP10
METRIC
All Dimensions in Millimeters
B
D
W
H
E
A
C
BORE
DIA
+.000
- .013
4.826
6.350
7.938
9.525
12.700
15.875
ROLLER
OUTER DIA.
+.000
-.013
19.746
22.896
31.750
36.513
42.863
49.213
INNER RACE
WIDTH
+.000
-.127
7.544
12.294
14.173
15.748
15.748
15.748
OUTER RACE
WIDTH
+.000
-.127
6.858
8.509
9.525
11.913
12.700
12.700
45 DEG
CHAMFER
+.38
-.00
0.13
0.13
0.38
0.38
0.38
0.38
THRUST
RING
DIA
(REF)
8.89
10.41
11.94
14.99
19.56
21.59
45 DEG
CHAMFER
+.38
-.00
0.56
0.81
0.81
0.81
1.12
1.12
OUTER
RACE
INNER
RACE
THRUST
RING
LINER
DESIGNATION
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
KARON
(SEE TABLE 1 FOR
LINER OPTIONS)
ADD SUFFIX “Z”
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
RADIAL
STATIC
LIMIT
LOAD
(KN)
See Notes
1&2
AXIAL
STATIC
LIMIT
LOAD
(KN)
WEIGHT
KG
(REF)
15.2
26.1
34.0
59.7
78.6
98.3
9.1
11.1
13.1
16.8
23.1
27.6
0.018
0.032
0.063
0.104
0.141
0.172
NOTES:
1. Load ratings shown are based on KAron V liner system.
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
Page 30
Track Rollers, Cam Followers & Airframe Bearings
C
Dimensionally Equivalent to MS27641 Series
W
(2 PL)
KARON
LINER
H
ADD
D
KRP ( )A Series – Self-Lubricating, Narrow
Airframe/Pivot Bearings
"Z" FOR SEAL
E
B
Part Number Example:
KRP 06 A V Z P
OPTION
KRP = KAron Bearing Prefix
–06 = 9.525 mm ID (Diameter in 1/16 inch increments)
A = Narrow Airframe/Pivot Bearing
V = KAron V Liner (See Table 1 for liner Options)
Z = Add “Z” for Seal Option
P = Add “P” for OD Cadmium Plate Option (per QQ-P-416
Type II, Class 2)
A
(2 PL)
For all Sizes:
Radial Play = 0.038 to 0.089 mm
Axial Play = 0.127 to 0.381 mm
LASER OR ELECTRON
BEAM WELD
KRP( ) A
SERIES
BEARING
NUMBER
KRP03A
KRP04A
KRP05A
KRP06A
KRP08A
KRP10A
KRP12A
KRP16A
KRP20A
METRIC
All Dimensions in Millimeters
B
D
W
H
E
A
C
BORE
DIA
+.000
- .013
4.826
6.350
7.938
9.525
12.700
15.875
19.050
25.400
31.750
ROLLER
OUTER DIA.
+.000
-.013
15.875
19.050
20.638
22.225
28.575
34.925
41.275
50.800
57.150
INNER RACE
WIDTH
+.000
-.127
7.544
7.137
7.544
7.950
9.525
10.312
11.100
12.700
12.700
OUTER RACE
WIDTH
+.000
-.127
5.944
5.563
5.944
6.350
7.950
8.738
9.525
11.125
11.125
45 DEG
CHAMFER
+.38
-.00
0.13
0.13
0.38
0.38
0.38
0.38
0.38
0.38
0.38
THRUST
RING
DIA
(REF)
8.890
10.414
11.938
13.716
16.764
20.066
23.368
31.496
37.592
45 DEG
CHAMFER
+.38
-.00
0.41
0.41
0.41
0.41
0.41
0.81
0.81
0.81
0.81
OUTER
RACE
INNER
RACE
THRUST
RING
LINER
DESIGNATION
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
KARON
(SEE TABLE 1 FOR
LINER OPTIONS)
ADD SUFFIX “Z”
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
RADIAL
STATIC
LIMIT
LOAD
(KN)
See Notes
1&2
AXIAL
STATIC
LIMIT
LOAD
(KN)
WEIGHT
KG
(REF)
10.1
10.7
13.6
18.7
34.3
50.3
66.5
111.2
132.7
9.1
10.2
13.1
15.4
19.4
23.8
27.8
37.5
45.9
0.009
0.014
0.014
0.018
0.036
0.054
0.086
0.141
0.163
NOTES:
1. Load ratings shown are based on KAron V liner system.
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
Page 31
Track Rollers, Cam Followers & Airframe Bearings
KRP ( )B Series – Self-Lubricating, Narrow
Airframe/Pivot Bearings
W
C
Dimensionally Equivalent to MS27642 Series
H
(2 PL)
ADD
"Z" FOR SEAL
OPTION
Part Number Example:
KRP 16 B V Z P
E
KRP = KAron Bearing Prefix
16 = 25.400 mm ID (Diameter in 1/16 inch increments)
B = Airframe/Pivot Bearing
V = KAron V Liner (See Table 1 for liner Options)
Z = Add “Z” for Seal Option
P = Add “P” for OD Cadmium Plate Option (per QQ-P-416
Type II, Class 2)
(2 PL)
D
A
B
For all Sizes:
Radial Play = 0.038 to 0.089 mm
Axial Play = 0.127 to 0.381 mm
KARON
LINER
METRIC
All Dimensions in Millimeters
LASER OR ELECTRON
BEAM WELD
KRP( ) B
SERIES
BEARING
NUMBER
KRP16B
KRP21B
KRP23B
KRP25B
KRP29B
KRP33B
KRP37B
KRP47B
KRP49B
B
D
W
H
E
A
C
BORE
DIA
+.000
- .025
25.400
33.350
36.525
39.700
46.050
52.400
58.750
74.625
77.800
ROLLER
OUTER DIA.
+.000
-.025
44.450
52.388
55.563
58.738
65.088
71.438
77.788
98.425
101.600
INNER RACE
WIDTH
+.000
-.127
11.100
11.100
11.100
11.100
11.100
11.100
11.100
13.487
13.487
OUTER RACE
WIDTH
+.000
-.127
9.525
9.525
9.525
9.525
9.525
9.525
9.525
11.913
11.913
45 DEG
CHAMFER
+.38
-.00
0.61
0.61
0.61
0.61
0.61
0.61
0.61
0.99
0.99
THRUST
RING
DIA
(REF)
30.480
38.354
41.656
44.704
51.054
57.404
63.754
79.756
82.804
45 DEG
CHAMFER
+.38
-.00
0.61
0.61
0.61
0.61
0.61
0.61
0.61
0.99
0.99
RADIAL
STATIC
LIMIT
LOAD
(KN)
See Notes
1&2
AXIAL
STATIC
LIMIT
LOAD
(KN)
WEIGHT
KG
(REF)
86.7
109.2
118.5
127.2
145.3
163.4
181.5
245.2
254.5
36.9
47.3
51.6
55.6
64.0
72.4
80.8
101.9
105.9
0.082
0.104
0.109
0.118
0.132
0.150
0.163
0.331
0.340
NOTES:
1. Load ratings shown are based on KAron V liner system.
OUTER
RACE
INNER
RACE
THRUST
RING
LINER
DESIGNATION
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
KARON
(SEE TABLE 1 FOR
LINER OPTIONS)
ADD SUFFIX “Z”
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
Page 32
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
Track Rollers, Cam Followers & Airframe Bearings
KRP( )BS Series – Self-Lubricating, Torque Tube,
Airframe, Pivot Bearings
W
Dimensionally Equivalent to MS27648 Series
C
H
(2 PL)
ADD
RAD
"Z" FOR SEAL
Part Number Example:
KRP 23 BS V Z P
OPTION
KRP = KAron Bearing Prefix
23 = 1.4380 Bore Diameter (Diameter in 1/16 increments)
BS = Self-aligning Torque Tube Bearing
V = KAron V Liner (See Table 1 for liner Options)
Z = Add “Z” for Seal Option
P = Add “P” for OD Cadmium Plate Option (per QQ-P-416
Type II, Class 2)
E
(2 PL)
D
J
A
B
KARON
LINER
For all Sizes:
Radial Play = 0.038 to 0.089 mm
Axial Play = 0.127 to 0.381 mm
LASER OR ELECTRON
BEAM WELD
METRIC
All Dimensions in Millimeters
KRP( )BS
SERIES
BEARING
NUMBER
KRP16BS
KRP21BS
KRP23BS
KRP25BS
KRP29BS
KRP33BS
KRP37BS
KRP47BS
KRP48BS
KRP49BS
B
D
W
H
E
A
C
J
BORE
DIA
+.000
- .025
25.400
33.350
36.525
39.700
46.050
52.400
58.750
74.625
76.200
77.800
ROLLER
OUTER DIA.
+.000
-.025
49.213
57.150
60.325
63.500
69.850
76.200
82.550
104.775
107.950
107.950
INNER RACE
WIDTH
+.000
-.127
11.100
11.100
11.100
11.100
11.100
11.100
11.100
13.487
13.487
13.487
OUTER RACE
WIDTH
+.000
-.127
9.525
9.525
9.525
9.525
9.525
9.525
9.525
11.913
11.913
11.913
45 DEG
CHAMFER
+.38
-.00
0.61
0.61
0.61
0.61
0.61
0.61
0.61
0.99
0.99
0.99
THRUST
RING
DIA
(REF)
30.480
38.354
41.656
44.704
51.054
57.404
63.754
79.756
82.804
84.328
45 DEG
CHAMFER
+.38
-.00
0.61
0.61
0.61
0.61
0.61
0.61
0.61
0.99
0.99
0.99
TO
SHARP
CORNER
(REF)
43.43
51.56
54.74
57.96
64.39
70.87
77.22
97.66
100.84
100.84
OUTER
RACE
INNER
RACE
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
OUTER RACE
SELFALIGNING
RING
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
THRUST
RING
LINER
DESIGNATION
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
KARON
(SEE TABLE 1 FOR
LINER OPTIONS)
ADD SUFFIX “Z”
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
Page 33
RADIAL
STATIC
LIMIT
LOAD
(KN)
See Notes
1&2
AXIAL
STATIC
LIMIT
LOAD
(KN)
WEIGHT
KG
(REF)
86.7
109.2
118.5
127.2
145.3
163.4
182.3
245.2
254.5
254.5
36.9
47.3
51.6
55.6
64.0
72.4
80.8
101.9
105.9
105.9
0.100
0.122
0.132
0.145
0.159
0.181
0.195
0.399
0.413
0.413
NOTES:
1. Load ratings shown are based on KAron V liner system.
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
Track Rollers, Cam Followers & Airframe Bearings
W
C
(2 PL)
Dimensionally Equivalent to MS27644 Series
H
KARON
LINER
ADD
D
KRP ( )P Series – KAron Lined, Self-Lubricating,
Wide Airframe/Pivot Bearings
E
B
(2 PL)
Part Number Example:
KRP 06 P V Z P
"Z" FOR SEAL
OPTION
KRP = KAron Bearing Prefix
–06 = 9.525 mm ID (Diameter in 1/16 inch increments)
P = Wide Airframe/Pivot Bearing
V = KAron V Liner (See Table 1 for liner Options)
Z = Add “Z” for Seal Option
P = Add “P” for OD Cadmium Plate Option (per QQ-P-416
Type II, Class 2)
A
(2 PL)
For all Sizes:
Radial Play = 0.038 to 0.089 mm
Axial Play = 0.127 to 0.381 mm
LASER OR ELECTRON
BEAM WELD
METRIC
All Dimensions in Millimeters
KRP( ) P
SERIES
BEARING
NUMBER
KRP03P
KRP04P
KRP05P
KRP06P
KRP08P
KRP10P
B
D
W
H
E
A
C
BORE
DIA
+.000
- .013
4.826
6.350
7.938
9.525
12.700
15.875
ROLLER
OUTER DIA.
+.000
-.013
19.746
22.896
31.750
36.513
42.863
49.213
INNER RACE
WIDTH
+.000
-.127
12.573
15.748
18.923
22.098
23.673
25.273
OUTER RACE
WIDTH
+.000
-.127
12.014
12.471
17.450
20.168
21.742
23.368
45 DEG
CHAMFER
+.38
-.00
0.13
0.13
0.38
0.38
0.38
0.38
THRUST
RING
DIA
(REF)
8.890
10.414
12.700
15.875
18.669
22.606
45 DEG
CHAMFER
+.38
-.00
0.46
0.81
0.81
0.81
1.12
1.12
RADIAL
STATIC
LIMIT
LOAD
(KN)
See Notes
1&2
AXIAL
STATIC
LIMIT
LOAD
(KN)
WEIGHT
KG
(REF)
30.4
41.5
72.9
119.2
187.9
260.2
9.0
11.1
14.4
16.8
20.8
25.1
0.027
0.041
0.109
0.159
0.249
0.340
NOTES:
1. Load ratings shown are based on KAron V liner system.
OUTER
RACE
INNER
RACE
THRUST
RING
LINER
DESIGNATION
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
KARON
(SEE TABLE 1 FOR
LINER OPTIONS)
ADD SUFFIX “Z”
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
Page 34
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
Track Rollers, Cam Followers & Airframe Bearings
KRPB500 Series – Self-Lubricating, Narrow
Airframe, Pivot Bearings
Dimensionally Equivalent to MS27646 Series
W
C
H
(2 PL)
ADD
"Z" FOR SEAL
OPTION
Part Number Example:
KRPB 540 V Z P
E
(2 PL)
D
KRPB = KAron Bearing Prefix
540 = 22.225 mm ID (Diameter in 1/16 inch increments)
V = KAron V Liner (See Table 1 for liner Options)
Z = Add “Z” for Seal Option
P = Add “P” for OD Cadmium Plate Option (per QQ-P-416
Type II, Class 2)
A
B
KARON
LINER
For all Sizes:
Radial Play = 0.038 to 0.089 mm
Axial Play = 0.127 to 0.381 mm
LASER OR ELECTRON
BEAM WELD
METRIC
All Dimensions in Millimeters
KRPB500
SERIES
BEARING
NUMBER
KRPB538
KRPB539
KRPB540
KRPB541
KRPB542
KRPB543
KRPB544
KRPB545
KRPB546
B
D
W
H
E
A
C
BORE
DIA
+.018
- .018
15.875
19.050
22.225
26.988
33.338
39.688
46.063/46.012
52.413/52.362
58.763/58.712
ROLLER
OUTER DIA.
+.000
-.025
26.988
30.163
33.338
38.100
44.450
50.800
57.150/57.112
66.675/66.637
73.025/72.987
INNER RACE
WIDTH
+.000
-.127
7.137
7.137
7.137
7.137
7.137
7.137
7.137
7.137
7.137
OUTER RACE
WIDTH
+.000
-.127
6.350
6.350
6.350
6.350
6.350
6.350
6.350
6.350
6.350
45 DEG
CHAMFER
+.51
-.00
0.38
0.38
0.38
0.38
0.38
0.38
0.38
0.38
0.38
THRUST
RING
DIA
(REF)
20.320
23.114
26.416
30.988
37.338
43.688
50.038
57.912
64.770
45 DEG
CHAMFER
+.51
-.00
0.38
0.38
0.38
0.38
0.38
0.38
0.38
0.38
0.38
OUTER
RACE
INNER
RACE
THRUST
RING
LINER
DESIGNATION
AMS 5643
(17-4PH)
Rc 28 MIN
(COND H1150
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
AMS 5643
(17-4PH)
Rc 40 MIN
(COND H900
REFERENCE)
KARON
(SEE TABLE 1 FOR
LINER OPTIONS)
ADD SUFFIX “Z”
TO P/N FOR
SEAL OPTION
(ACETAL RESIN
OR NYLON)
RADIAL
STATIC
LIMIT
LOAD
(KN)
See Notes
1&2
AXIAL
STATIC
LIMIT
LOAD
(KN)
WEIGHT
KG
(REF)
27.8
31.2
36.1
42.3
51.0
59.7
68.3
79.8
27.8
23.5
26.8
32.2
38.2
46.6
55.0
63.3
73.1
23.5
0.018
0.023
0.027
0.032
0.036
0.041
0.045
0.073
0.077
NOTES:
1. Load ratings shown are based on KAron V liner system See
Table 1 for liner Options
2. Loads shown are based on bearing components only,
bolt/pin shear is not considered.
Page 35