© The Dezac Group 2015 © The Dezac Group 2015

Transcription

ACNE
Q
© The Dezac Group 2015
Advanced blue light
acne clearing
Advanced
bluesystem
light
acne clearing system
user guide
WARNINGS
•Read all instructions thoroughly
and retain for future reference.
•To prevent cross contamination, this
product is not recommended for multiple
users.
•Avoid direct contact with eyes.
•Do NOT look directly into the light.
•Do not use the light on or around your
eyes or eyelids.
•We recommend eyes are closed when
treating near the eye region.
•Do not treat moles, warts, open sores or
on any skin conditions other than acne.
•NOT for use on or by children under 12
years old. Not for use on or by children
between 12 and 17 years old without
parental supervision.
•The treatment head needs to be in constant
contact with the skin during treatment.
•In case of Pre-Treatment Facial Wash or
Post-Treatment Moisturiser contact with
the eyes, do NOT rub. Rinse with copious
amounts of water or eye wash. If irritation
persists seek medical assistance.
•This appliance is not intended for use by
persons, including children, with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision
or instructions concerning use of the
appliance by a person responsible for
their safety.
•Do NOT attempt to drive or use any other
potentially hazardous equipment whilst
using Q-Acne.
•Not suitable for use in an oxygen rich
environment.
•The unit may reach temperatures up to a
maximum 44°C after repeated use.
!
WARNINGS
CONTRAINDICATIONS
•Do NOT dismantle the unit or power
adapter, there are no user serviceable parts
inside. No modification of this equipment
is allowed. In the event of a fault, Rio or
its service agent or a similarly qualified
person must replace it in order to avoid
a hazard.
•The product can be disconnected from
the mains supply by unplugging the
power adapter. Please ensure that the
power adapter is positioned so that it is
easily accessible.
•Only use the power adapter supplied with
this product.
•Do NOT immerse the unit in water. Wiping
with a damp cloth is sufficient to clean.
•For external use only.
•Do not switch the device on until the
treatment head is in contact with the skin.
NOT suitable for people who are
•
photosensitive or who have photosensitive
skin. Common medications can cause
photosensitivity so if you are taking
any medication you should check for
photosensitivity warnings and if in doubt,
consult your doctor.
!
WELCOME
KNOW YOUR Q-ACNE SYSTEM
The Q-Acne Advanced Blue Light Acne Clearing System
eliminates the acne-causing bacteria beneath the surface
of the skin to help clear existing acne and prevent future
outbreaks.
Treatment lights
Treatment head
The Pre-Treatment Facial Wash is both a cleanser, to
help remove any traces of dirt and make-up and a mild
exfoliant. Using the Facial Wash aids the
penetration of the blue light into
the skin.
Battery indicator lights
ON/OFF button
The
Post-Treatment
Moisturiser is specially
formulated to help
maintain skin hydration.
Power adapter
Charging dock
Pre-Treatment
Facial Wash
Q-Acne unit
Post-Treatment
Moisturiser
Q ACNE
Advanced blue light
3
Q-ACNE TREATS MILD TO MODERATE ACNE*
Is Q-ACNE for you?
COMEDONAL SPOTS
X
MILD ACNE*
3
MODERATE ACNE*
3
SEVERE ACNE*
X
No inflamed spots
Total spot count
TYPE OF SPOTS
Whiteheads
(non-inflamed spot
with a white centre)
No more than a few
Blackheads
(non-inflamed spot
with a black centre )
Inflamed spot(s)
(small red bumps, tender to touch)
none
Inflamed (small red bumps, tender
to touch containing pus with white
heads)
none
Inflamed (larger red lumps deeper
within skin, painful, signs of scarring)
none
less than 30 in total
30-125 in total
more than 125 in total
OR
OR
OR
less than 20
between 20-100
more than 100
OR
OR
OR
PATCH TEST
less than 15
between 15-50
more than 50
none
none
more than 5
✓
Important: Before treating your face, it’s important to carry out a patch test on your forearm as your skin could be sensitive to light due to other medications or medical
conditions. It is normal to feel warmth from the blue light. However, if you feel pain or your skin gets uncomfortably hot during treatment, then Q-Acne is not suitable for you.
Following the patch test application, wait 24 hours. If you notice any difference between the treated and untreated skin, such as redness, discoloration or discomfort, you
should seek advice from a medical professional, do not continue treatment.
*based on the Combined Acne Severity Classification by the US Agency for Healthcare Research and Quality (AHRQ).
4
Q ACNE
Advanced blue light
FREQUENTLY ASKED QUESTIONS
CHARGING
What causes Acne?
IMPORTANT: C
harge the unit for 4 hours before using for the
first time.
Acne is a condition of the sebaceous hair follicle. The hair follicles, or
pores, in your skin contain sebaceous glands. These glands make
sebum; an oil that lubricates hair and skin. Normally, sebum travels
through the hair follicle to the skin surface. With acne, sebum is
trapped, clogging the follicle. Bacteria that causes acne are called
Propionibacterium acnes (P.acnes) and are present on everybody’s
skin. When the sebaceous gland gets clogged, it becomes a breeding
ground for P.acnes, which multiply rapidly and result in acne.
1
STEP 1
To charge, connect the power adapter into the
charging dock and plug into the mains.
How often should I use Q-Acne?
2
Treat all areas for 3 minutes every other day. Clinical studies have
demonstrated the effectiveness of treatments every other day.
When will I see results?
You should see a positive change in your skin condition within 3
weeks. Treatment every other day is recommended for a minimum of
8 weeks. After this, use in line with any continued occurrence or new
outbreaks.
STEP 2
Place the unit in the charging dock. While
charging, the lights around the ON/OFF button
will illuminate in rotation. When fully charged,
all lights will go out and the unit will be ready
to use.
LOW BATTERY INDICATION
When the battery level is low all four lights will
flash to indicate recharging is required. The unit
will turn off when the battery is flat.
Is there a risk of sunburn or skin cancer?
No. The peak wavelengths of light used by the blue light unit are
outside those that could cause damage to the skin.
Can I use my usual anti-spot cream/lotion?
Q-Acne should be applied to clean, dry skin. Between treatments you
can use your usual anti-spot cream/lotion.
Q ACNE
Advanced blue light
5
USING Q-ACNE
1
2
STEP 1: Pre-Treatment Facial Wash
3
Splash your face with warm water. Pump a pea
size quantity of facial wash on to your fingers
and apply to the entire face. Rinse off with clean
warm water. Pat the skin dry before using the
Q-Acne blue light treatment.
STEP 3: Post-Treatment Moisturiser
Once the blue light treatment is complete, apply
the Post-Treatment Moisturiser to your entire
face and allow it to be absorbed into your skin.
NOTE: In between treatments, the Pre-Treatment Facial Wash and
Post-Treatment Moisturiser can be used alone as part of your
normal everyday skincare regime.
STEP 2: Blue Light Treatment
Gently place the treatment head over the area of
the skin to be treated. To begin treatment,
press the ON/OFF button until the treatment
lights illuminate. Whilst the treatments lights
are on, the treatment head should be kept in
constant contact with the skin.
3
IMPORTANT:
Do not use the Q-ACNE Advanced Blue Light treatment on or around
your eyes or eyelids.
Do not look directly into the treatment lights. Doing so could result
in injury.
Keep the treatment head in constant contact
with the skin being treated and hold in position
for 3 minutes.
Do not re-treat an area within 24 hours.
The unit will automatically switch off after 3 minutes.
Move to the next area to be treated and press the
ON/OFF button to start the treatment. Continue
until all areas are treated.
CLEANING
A damp cloth should be used to wipe clean the unit after use.
Do not use abrasives as they may damage the device.
To switch the unit off at any time, press the
ON/OFF button.
NOTE: If your skin becomes uncomfortably hot remove the unit. The
treatment head should be in constant contact with the skin,
whilst the treatment lights are on.
6
Q ACNE
Advanced blue light
DECLARATION OF COMPLIANCE
SAFETY SYMBOLS
The Q-Acne blue light emitter (LITE3) and its power adapter together constitute
a Medical Electrical System as defined in EN60601-1:2006
In accordance with the Medical Devices 93/42/EEC as amended by Directive
2007/47/EC, this product has a declared life of 5 years.
0120
The patient is an intended operator.
This product conforms to the Medical Devices 93/42/EEC as amended
by Directive 2007/47/EC
This product is intended for indoor use only.
Device is Class II when located in the charging dock. It is internally powered
when removed from the charging dock.
Read instructions carefully before use.
Ocular Safety
Denotes manufacturer of the device.
The Q-Acne blue light emitter (LITE3) has been tested to EN 62471: 2008 and
has been classified as non hazardous.
Denotes date of manufacture.
SPECIFICATION OF Q-ACNE BLUE LIGHT EMITTER (LITE3)
This product is a Type BF Applied Part. This product is intended to
be in contact with the user in normal use.
MODEL NUMBER: LITE3
Light Source
Output Frequency
17 LEDs
Blue Light - 415nm
Class II Insulation
POWER ADAPTER: 1-ADKS-6-10-WH
KSAS7R50600100D5
Input
Output
100–240V AC, 50/60Hz, 0.25A
6V DC 1000mA
ENVIRONMENT
Operating Temperature 5–30 degrees Celsius
Humidity
20%–60% RH
Atmospheric Pressure 700–1060 hPa
Storage & Temperature
-5–40 degrees Celsius
Transport Humidity
5%–90% RH
Q ACNE
Advanced blue light
7
MANUFACTURER’S DECLARATION OF EMC
Manufacturer’s declaration - electromagnetic emissions
The LITE3 is intended for use in the electromagnetic environment specified below.
Emissions Test
RF Emissions CISPR 11
Compliance
Electromagnetic environment - guidance
Group 1
The model LITE 3 uses RF energy only for its internal function.
Therefore, its RF emissions are very low and are not likely to
cause any interference in nearby electronic equipment.
RF Emissions CISPR 11
Class B
Harmonic emissions IEC 61000-3-2:2005
Not applicable
Voltage fluctuations / flicker emissions IEC 61000-3-
Not applicable
The model LITE 3 is suitable for use in all establishments including domestic establishments and those directly connected
to the public low- voltage power supply network that supplies
buildings used for domestic purposes.
8
Q ACNE
Advanced blue light
MANUFACTURER’S DECLARATION OF EMC
Manufacturer’s declaration – electromagnetic immunity
The LITE3 is intended for use in the electromagnetic environment specified below.
Immunity Test
Electrostatic discharge (ESD) IEC 610004-2:2009
IEC 60601
test level
Compliance level
Electromagnetic environment - guidance
± 6 kV Contact
± 8 kV Air
± 6 kV Contact
± 8 kV Air
Floors should be wood, concrete or ceramic tile. If floors are
covered with synthetic material, the relative humidity should be
at least 30%.
Conducted RF
IEC 61000-4-6:2009
3Vrms
150kHz to 80MHz
1Vrms
Radiated RF immunity
IEC 61000-4-3:2006
3V/m
80MHz to 2.5GHz
3V/m
80MHz to 2.5GHz
± 2 kV for power supply lines
± 2 kV for power supply lines
Electrical fast transient/burst IEC 610004.4:2004 +A1
Portable and mobile RF communications equipment should be
used no closer to any part of the LITE 2, including cables, than
the recommended separation distance calculated from the equation applicable to the frequency of the transmitter.
Recommended separation distance
d=3.5ÖP
d=1.2ÖP 80MHz to 800MHz d=2.3ÖP 800MHz to 2.5GHz
Where P is the maximum output power rating of the transmitter in
watts (W) according to the transmitter manufacturer and d is the
recommended separation distance in metres (m).
Mains power quality should be that of a typical commercial or
hospital environment.
Surge
IEC 61000-4-5:2005
± 1kV line(s) to line(s)
± 2kV line(s) to earth
± 1kV differential mode
± 2kV common mode
Voltage dips, short interruptions and voltage variations on power supply input lines
IEC61000-4-11:2004
<5 % UT
(>95 % dip in UT) for 0,5 cycle
40 % UT
(60% dip in UT) for 5 cycles
70 % UT
<5 % UT
(>95 % dip in UT) for 5 s
<5 % UT
(>95 % dip in UT) for 0,5 cycle
40 % UT
70 % UT
<5 % UT
(>95 % dip in UT) for 5 s
Power frequency (50/60 Hz) magnetic field
IEC 61000-4-8:2010
3 A/m
3 A/m
Note 1: UT is the a.c. mains voltage prior to application of the test level. Note 2: Please refer to IEC60601-1 for further clarification
Q ACNE
Advanced blue light
9
C U ST O M ER C A R E
If you have any questions or experience any difficulties, please call our Rio Careline on +44 (0) 1242 702345 or email us at: [email protected]
To reorder additional accessories, please visit www.riobeauty.com or contact your local distributor.
GUARANTEE
To register your two year guarantee online, visit: www.riobeauty.com/warranty_online.htm
DISPOSAL
The Waste of Electrical and Electronic Equipment (WEEE) Directive (2012/19/EU) has been put in place to recycle products using best available recovery and
recycling techniques to minimise the impact on the environment, treat any hazardous substances and avoid the increasing landfill. The unit and adapter are
classed as Electrical or Electronic equipment so please ensure that at the end of the life of this control unit and battery, they are disposed of in the correct
manner in accordance with local authority requirements. They must NOT be disposed of with household waste.
10
Q ACNE
Advanced blue light
www.riobeauty.com
UK
Rio, Dezac and Q-ACNE are trademarks of The Dezac Group Ltd ©The Dezac Group Ltd 2015.
Manufactured by The Dezac Group Ltd, Dezac House, Montpellier Street, Cheltenham, Gloucestershire, GL50 1SS, UK
1-IN-LITE3-UK/1.0

© The Dezac Group 2015 © The Dezac Group 2015

Transcription

Similar documents

RAVLIN CONGREGATE CENTER

See here for more details

Botinol This clinically proven, four step treatment effectively reduces

Sublative™ Acne Scar Treatment FAQ , s

For more information and pricing, read our aesthetic services brochure

psychodermatology march 15.cdr

Consult the PDF.

the full brochure here

Treatment of Acne Scars with the Infini (fractionated

Smoothbeam Laser Treatment Of Acne Vulgaris