Amerex Instruments Catalog-NA

Transcription

1 | Amerex Instruments | AmerexInst.com | 1-888-263-7392
Table of Contents
GYROMAX™ INCUBATOR SHAKERS ...........................................................................................3
GYROMAX™ OPEN AIR SHAKERS ...............................................................................................4
MODELS 818, 828, AND 838 SPECIFICATIONS .......................................................................4
WATER BATH SHAKERS................................................................................................................5
MODELS 929, 939, 939XL SPECIFICATIONS ...........................................................................5
INCUMAX™ INCUBATORS (WITHOUT REFRIGERATION) ..........................................................6
MODELS IC80, IC150, IC250, IC500 SPECIFICATIONS ...........................................................6
INCUMAX™ IC150R, IC500R (WITH REFRIGERATION) ...............................................................7
MODELS IC150R AND IC500R SPECIFICATIONS....................................................................7
HYBRIDIZATION OVENS ................................................................................................................8
MODELS HS-101 AND HS-111 SPECIFICATIONS....................................................................8
CONVECTION OVENS: INCUMAX™ .............................................................................................9
MODELS CV80, CV150 AND CV250 SPECIFICATIONS ...........................................................9
WATER BATH WITH CIRCULATING PUMP: INCUMAX™..........................................................10
MODEL WB20C SPECIFICATIONS .........................................................................................10
CIRCULATING BATHS: LOW-TEMPERATURE ..........................................................................11
MODEL CB212 AND CB222 SPECIFICATIONS ......................................................................11
CRYOPROOF™ 313 TUBE SEALER SPECIFICATIONS .............................................................12
MODEL 313 SPECIFICATIONS ................................................................................................12
INCUBATOR/SHAKER/OVEN ACCESSORIES ............................................................................13
GYROMAX™ INCUBATOR SHAKERS
Amerex's GYROMAX™ and SteadyShake™ orbital shakers incorporate design features that offer quiet,
maintenance-free shaking under a constant and reproducible temperature environment. Eleven different
models meet the needs of most biological research laboratories for shaking under a precisely controlled
temperature environment are available in four basic housing configurations.
STEADYSHAKE™ 757 AND 757L BENCHTOP
The SteadyShake™ 757 and 757L are economical and compact benchtop incubator
shakers. The 757 occupies only 18"W x 19"D of space, and the 757L is slightly larger
(20.5"W x 25.5"D) for increased flask capacity. The 757 can accommodate four 2-liter
Erlenmeyer or two 2.8-liter Fernbach flasks, and the 757L five and four of these, respectively.
The lid has a large viewing window and a microprocessor temperature controller maintains
precise temperature control from 3°C above ambient to 70°C. A quiet fan ensures air and
temperature uniformity throughout the chamber. The brushless, maintenance-free drive motor
generates speeds from 40 to 400 RPM (60 Hz frequency) which is displayed on a digital
readout. A triple-eccentric drive with counter-balancing weights provides smooth and quiet
shaking, and eliminates the inconvenience of making balancing adjustments as the load
increases. The timer switch affords a choice of flipping between a continuous run and a timed
run up to 99 hours and 59 minutes. An independent over-temperature thermostat,
conveniently located on the control panel, prevents over-heating.
MODEL 727 AND 737 -BENCHTOP/UNDER BENCH TYPE
The 727 (height, 30.3"), 737 (height, 33.5"), and 747 (height 32.6") can fit on or under most
workbenches. All these models can be stacked to save valuable laboratory space. The 727 is
compact and occupies only 20"W x 27"D of space. With a height of 30.3", it can fit on or under
a workbench. You can also stack two 727 units. The chamber holds a 15"W x 15"D platform
and accommodates flasks up to 4 liters. Using the shelf (one is included) and the shaking
platform, you can incubate Petri dishes and shake flasks at the same time. You can adjust the
shelf height and use more than one shelf in the chamber.
MODELS 737/737R AND 747/747R BENCH TYPE AND STACKABLE
The 737/737R Shakers have a footprint of 33"W x 24"D. This versatile, sturdy flat -top can
serve as a benchtop or you can stack two of the 737s, or a 737 and a 737R on top of each
other to save space. With a height of 34", the 737 can fit under many benchtops, while the taller
refrigerated 737R (at 41") cannot. The 20.5"W x 18.0"D platform is large enough to
accommodate nine 1-liter, six 2-liter, twenty-five 250-mL, or two 6-liter flasks. The 737 and
737R use the same shelf system as the 727. The 737R is equipped with a frost-free
refrigeration system for working at or below ambient temperature. The chamber has a built-in
outlet used for powering small equipment such as a cell bottle roller or a rocker. The 747/747R
design is similar to that of the corresponding 737/737R, but offers more capacity. They can
accommodate just as many or more flasks of a given size than the chest type 767/767R.They
also offer advantages over chest type shakers such as a shelf, a smaller footprint, and the
ability to stack two units. The 787/787R are affordably priced models with similar performance
as the 737/737R and 747/747R. These are excellent alternatives when there is a budget
constraint.
MODELS 767/767R AND 777/777R CHEST TYPE
The 767/767R and 777/777R are chest type incubator shakers that are mounted on casters.
They feature a front glass window that enables the user to look into the chamber when away
from the shaker. The 767/767R accommodates a 30"W x 18"D platform while the 777/777R,
with a 38"W x 24"D platform, offers the most capacity among all chest type incubator shakers
in the marketplace. For example, they can accommodate twenty-four 1-L, fifteen 2-L, or six 6-L
flasks. In the refrigerated models 767R and 777R, a chamber temperature as low as 4°C can
be maintained
GYROMAX™ OPEN AIR SHAKERS
The 800 series of open-air shakers offer a choice of three shakers with five platform sizes. The largest model, 818, is a
large-capacity heavy-duty shaker with a 38" x 24" platform. Both the mid-size 828 and the smallest 838 offer a choice of
two platform sizes. The SK-838 is a compact unit, yet is large enough carry a significant load. The shakers feature
microprocessor control and digital RPM and timer readouts. The microprocessor regulates the speed to within ±1 RPM
of set point. The acceleration circuitry provides for a smooth ramp-up of speed to minimize splashing. The drive system
features a triple-eccentric drive that is dynamically balanced with counter weights This feature eliminates the need to
make adjustments as the load increases, and together with a low-profile design, ensures a smooth, stable and quiet
operation. A fan cools the drive motor to ensure a long life. A timer can be set to 99 hours and 59 minutes or to 9999
minutes in increments of one minute. If the timer is not needed, it can be easily disabled and the shaker set to run
continuously. In case of power failure, the timer will count from where it last stopped after it resumes running.
Maintenance-free brushless motor cooled by a fan for long life., Dynamically balanced, triple-eccentric drive for long life
and smooth, stable, and quiet operation. Eliminates need for adjustments as the speed changes. Shaking speed: 40 to
400 RPM (slightly lower at 50 Hz).Digital RPM setting and display in 1 RPM increments. In case of power failure, the
timer will count from where it last stopped when the shaker resumes running. Timer setting and display: 99 hours 59
minutes or 9999 minutes in 1 minute increments, or continuous. Timer can count up or down.
MODELS 818, 828 AND 838
GYROMAX™ 818, 828, AND 838 SPECIFICATIONS
Overall dimensions
Model 838 Regular:
15.7"W x 13.0"D x 6.5"H (400mmW x 330mmD x 165mmH)
Model 838 Oversize:
18.9"W x 15.0"D x 6.5"H (480mmW x 380mmD x 165mmH)
Model 828 Regular:
24"W x 19"D x 8.5"H (610mmW x 483mmD x 215mmH)
Model 828 Oversize:
Model 818:
Model 838 Regular:
15.7"W x 11.8"D (400mmW x 300mmD)
Model 838 Oversize:
18.9"W x 15.0"D (480mmW x 380mmD)
Model 828 Regular:
24"W x 19"D (610mmW x 483mmD)
Model 828 Oversize:
30"W x 18"D (760mmW x 460mmD)
Model 818:
38"W x 24"D (965mmW x 610mmD)
Platform dimensions
FLASK CAPACITY
Flask Size (mL)
50 125 250 500 1000 2000 2800 4000 6000
Model 838
40 24 15 10
6
4
2
2
1
Model 838 (Oversize) 42 30 20 12
8
5
3
2
1
80 48 30 20
12
6
3
3
3
Model 828 (Oversize) 112 60 40 24
15
12
6
6
6
160 104 70 40
24
15
8
8
8
Model 828
Model 818
GYROMAX™ WATER BATH SHAKERS
Amerex's GYROMAX™ orbital and reciprocating water bath shakers incorporate design features that offer
quiet, maintenance-free shaking under a precisely controlled and reproducible temperature environment.
MODELS 929, 939, AND 939XL
GYROMAX™ 929 is an orbital shaker with a 38-liter bath. Its 19.0"W x 12.5"D platform is
larger than any in the marketplace and can accommodate fifteen 250-mL flasks. The
platform assembly includes baffle for efficient water mixing.
GYROMAX™ 939 and 939XL are reciprocating bath shakers. The shaking speed and
shaking stroke are both adjustable. Model 939 has a 39-liter bath with a 15.7"W x 11.8"D
platform. Model 939XL is larger, and features a 54-liter bath with a 24.4"W x 11.8"D
platform for greater throughput. Each shaker incorporates a circulating pump to ensure
optimum mixing and temperature uniformity.
FEATURES: Microprocessor-controlled, Stainless steel bath, Maximum temperature to
100°C, Maintenance-free brushless motor ,Can handle flasks up to 2 liters.
FLASK CAPACITY
Flask Size (mL) 50 125 250 500 1000 2000
Model 929
35 24 15
8
6
4
Model 939
30 18 12
8
5
3
Model 939XL
50 32 21 14
8
5
WATER BATH SHAKER SPECIFICATIONS
MODEL
GYROMAX 929
GYROMAX 939
GYROMAX 939XL
TEMPERATURE
Range
Ambient +2°C to 100°C
Accuracy
±0.1°C
Uniformity
±0.1°C
Setting
Membrane keypad
Control
Microprocessor
Display
Digital to 0.1°C
SHAKING
Mode
Speed (slightly lower at 50 Hz)
Orbital
20 to 400 rpm
Reciprocating
10 to 200 oscillations/min
Display
Digital tachometer
MOTOR
Maintenance-free, brushless
HEATER
1500 watts
DIMENSIONS
Overall, W x D x H
(26 x 23 x 21) in (31.5 x 16.0 x 15.7) in (40.1 x 16.0 x 15.7)
(66 x 58 x 53) cm (80 x 41 x 40) cm
( 102 x 41 x 40) cm
Bath, W x D x H
(21 x 15 x 7.5) in (22.8 x 14.1 x 7.5) in (31.5 x 14.1 x 7.5) in
(53 x 38 x 19) cm (58 x 36 x 19) cm
(80 x 36 x 19) cm
Bath Capacity
38 liters
39 liters
54 liters
Platform, W x D
(19.3 x 12.5) in
(49 x 32) cm
(15.7 x 11.8) in
(40 x 30) cm
(24.4 x 11.8) in
(62 x 30) cm
SHIPPING WEIGHT
241 lb (110 kg)
160 lb (73 kg)
226 lb (103 kg)
POWER SOURCE
120V (220V available), 50/60Hz, 1500VA
INCUMAX™ INCUBATORS (WITHOUT REFRIGERATION)
IncuMax™ IC80, IC150, IC250, and IC500 incubators from Amerex feature a forced filtered air circulation
system that provides both exceptional temperature uniformity and rapid heat recovery throughout its
stainless steel chamber. The control panel is conveniently located at the top of the incubator. The door is
locked when closed. A heat-resistant silicone rubber provides durable and effective seal. Two refrigerated
models, IC150R and IC500R, are suitable for applications at/or below ambient temperature. An electrical
outlet enables small laboratory equipment to be operated inside the chamber.
The incubators feature an independent over-temperature thermostat that eliminates over-heating. A timer is
programmable from 1 minute to 99 hour and 59 minutes. Two adjustable shelves are supplied with the
IC80, IC150 & IC150R, three with the IC250, and four with the IC500 and IC500R.
IC80, IC150, IC250, AND IC500 (Without Refrigeration)
IncuMax™ IC80, IC150, IC250, and IC500 incubators from Amerex feature a PID
microprocessor controller and a forced air circulation system to provide both exceptional
temperature uniformity and rapid heat recovery throughout its stainless steel chamber. For the
IC-80 and IC150, you can stack one unit on top of another to conserve laboratory space. To
reduce contamination, forced air entering the chamber passes through a filter. The timer is
programmable from 1 minute to 99 hours and 59 minutes. The incubators also feature an
independent over-temperature thermostat that eliminates over-heating.
The control panel is conveniently located at the top of the incubator. The door is locked when
closed, providing a tight seal. A viewing window allows observation inside the chamber without
opening the door. For light-sensitive materials, you can use a sliding panel to cover the window.
A heat-resistant silicone rubber provides a durable and effective seal. Two adjustable shelves
are supplied with the IC80 and IC150, three with the IC250, and four with the IC500. An access
port allows access by temperature probes into the chamber.
INCUMAX™ INCUBATOR SPECIFICATIONS
MODEL
IC80
IC150
IC250
PID microprocessor temperature controller,
temperature set by control keypad to 0.1°C, digital LED
Temperature Controller
+5°C above ambient to 80°C
Range
Accuracy
±0.1°C
Uniformity
±0.5°C at 37°C
Circulation
Forced filtered air
Stainless steel
Chamber Material
2
Shelves Included
Max. No. Of Shelves
Timer
8
10
Chamber Dimensions (WxDxH)
Chamber Volume
Overall Dimensions (W x D x H)
4
12
30
One
Independent thermostat provides over-temperature protection
19.7" x 15.7" x 15.7" 23.6" x 19.7" x 19.7" 24" x 20" x 31.5" 27.6" x 23.4" x 47.2"
(50 x 40 x40) cm
(60 x 50 x 50) cm
(60 x 51 x 80) cm (70 x 59.5 x 120) cm
2.8 cu ft (80 liters)
5.3 cu ft (150 liters) 8.7 cu ft (245 liters) 17.7 cu ft (500 liters)
24.4" x 20.5" x 24.4" 28.3" x 24.4" x 28.3" 28.3" x 24.4 x 40.2" 31.1" x 31.5" 65"
(62 x 52 x 62) cm
(72 x 62 x 72) cm (72 x 62 x 103) cm (79 x 80 x 165) cm
120VAC, 50/60Hz, single phase (220V available)
Power Requirements
Shipping Weight
3
1 minute to 99 hours and 59 minutes or continuous
Probe Access Port
Over-Temperature Protection
IC500
134 lb (61 kg)
167 lb (76 kg)
275 lb (125 kg)
480 lbs (219 kg)
INCUMAX™ INCUBATORS (WITH REFIGERATION)
INCUMAX™ IC150R, IC500R (With Refrigeration)
The 5.3 cu. ft. IncuMax™ IC150R and 17.7 cu. ft. IC500R lowtemperature/BOD incubators from Amerex feature a microprocessor PID
controller and an efficient forced-air circulation system to provide
exceptional temperature uniformity and rapid heat recovery throughout its
stainless steel chamber. They are suitable for applications from -5°C to
65°C. The timer is programmable from 1 minute to 99 hours and 59
minutes. An electrical outlet enables a small laboratory equipment to be
operated inside the chamber. The incubators also feature an independent
over-temperature thermostat that eliminates over-heating.
The IC150R incorporates an inner glass door and two adjustable shelves
are included. The IC500R features a viewing window and four adjustable
shelves are included.
INCUMAX™ IC150R AND IC500R SPECIFICATIONS
MODEL
IC150R
IC500R
Microprocessor PID temperature controller, temperature set by control
keypad to 0.1°C, digital LED
Above -5°C to 65°C
Temperature Range
±0.1°C
Temperature Accuracy
Temperature Uniformity
±0.5°C at 37°C
±1.0°C at 37°C
Circulation
Compressor
Forced air
1/5 HP, R-134A
Stainless steel
Chamber Material
Chamber Shelf
1/3 HP, R-134A
Two included
Four included
Probe Access Port
One
Chamber Electrical Outlet
One
Timer
1 minute to 99 hours and 59 minutes, or continuous
Chamber Dimensions (W x D x H)
23.6" x 19.7" x 19.7"
(60 x 50 x50) cm
27.6" x 23.0" x 43.3"
(70cm x 59.5cm x120cm);
Chamber Volume
26.8" x 29.9" x 35.5"
(68cm x 76cm x 85cm)
31.1" x 31.5" x 65.0"
(79 cm x 80cm x 165 cm)
Power Requirements
120VAC, 50/60Hz, single phase (220V available)
Shipping Weight
280 lb (127 kg)
480 lb (218 kg)
HYBRIDIZATION OVENS
MODELS HS-101 AND HS-111
Amerex's model HS-111 is a versatile, compact hybridization oven that also functions as
an incubator shaker. It incorporates a microprocessor temperature controller that
together with a large and quiet circulating fan, assure uniform and precise temperature
control. The large 12.5" x 14.8" double-paned glass window enables one to clearly and
easily observe the inside of the entire stainless steel chamber.
The rotisserie can accommodate eight or sixteen 40-mm tubes, depending on their
length. It also can accommodate 50-mL, 15-mL, 1.5-mL and 2.0-mL tubes using
appropriate accessory clips. For tri-directional rotation, one can easily offset the two tube
holders of the rotisserie assembly by up to 20 degrees to generate a rotary action that
moves liquid from one end of the tube to the other. The resulting greater rigorous
washing action allows the use of less probe solution and effects greater hybridization
efficiency.
The HS-111 increases the versatility of a hybridization oven by incorporating a platform
for shaking Erlenmeyer flasks of size up to 500 mL. By removing the rotisserie from the
chamber - and this can be done in seconds - the platform can accommodate a 6-liter
flask. The platform can also be used for slowly shaking a tray used in wash procedures,
and is more convenient than removing the rotisserie and replacing it with a rocker
attachment. A unique, dynamically-balanced triple eccentric drive provides smooth and
quiet shaking up to 300 RPM, making the HS-111 a true incubator shaker for bacteria or
cell culture. The HS-101 is similar to the HS-111, except that it does not incorporate a
shaking platform.
MODELS HS-101 AND HS-111 SPECIFICATIONS
HS-111 (with shaking platform)
HS-101 (w/o shaking)
About 5°C above ambient to 70°C
Temperature Range
Speed 2 to 50 RPM
2 to 25 RPM
Shaking Speed
N/A
25 to 300 RPM (at 60 Hz)
Shaking Orbit
N/A
25 mm
Rotation
Temperature Control
PID microprocessor temperature controller to ±0.1°C
Temperature Display
Digital to 0.1°C
Accuracy / Uniformity
±0.1°C/±0.5°C at 37°C
Forced hot-air
Circulation
None
Dynamically balanced triple eccentric drive
13.8" x 9.9" x 9.9"
(35 x 25 x 25)cm
13.8" x 9.9" x 16.5"
(35 x 25 x 42)cm
Drive
Stainless steel
Chamber Material
17.3" x 16.9" x 17.0"
(44 x 43 x 43)cm
17.3" x 16.9" x 25.6"
(44 x 43 x 65)cm
None
12.2"W x 8.3"D (31W x 21D) cm
Platform Dimensions
Bottle Capacity
40 x 150mm (16), 40 x 300mm (8)
Power Source
120V (220V available on request)
62 lb
Shipping Weight
100 lb
FLASK CAPACITY
(*BOTTLES/ROTISSERIE MUST BE REMOVED TO INSERT FLASKS)
Flask Size
Number of Flasks
25 mL
50 mL
125 mL
250 mL
*500 mL
*1 L
*2 L - 6 L
24
15
12
8
5
2
1
CONVECTION OVENS: INCUMAX™
CV80, CV150 AND CV250
IncuMax™ CV80, CV150 and CV250 convection ovens from Amerex, feature a
microprocessor temperature controller with simultaneous displays of the set temperature
(up to 250°C) and oven temperature. In addition, a drying time up to 99 hours and 59
minutes can be programmed. A two-speed fan provides forced convection for uniform
temperature distribution and rapid heat recovery throughout the stainless steel chamber.
An adjustable air exhaust, which can be fully closed to fully open, is provided to control
the rate of drying, baking or curing.
The control panel is conveniently located at the top of the oven. The door is locked when
closed. A heat-resistant silicone rubber provides a durable and effective seal. Two
adjustable shelves are supplied with the CV80 and CV150 and three with the CV250.
INCUMAX™ CV80, CV150 AND CV250 SPECIFICATIONS
MODEL
CV80
CV150
Microprocessor temperature controller, temperature set
by control keypad to 0.1°C, digital LED
+5°C above ambient to 250°C
Temperature Range
±0.1°C at 100°C, ±0.2°C at 250°C
Temperature Accuracy
±1°C at 100°C
Temperature Uniformity
Circulation
Forced air - two speed selectable with a switch
Stainless steel
Chamber Material
2
Shelves Included
Max. No. Of Shelves
Timer
8
1
10
12
1 minute to 99 hours and 59 minutes or continuous
One
Probe Access Port
CV250
19.7" x 15.7" x 15.7"
(50cm x 40cm x 40cm)
23.6" x 19.7" x 19.7"
(60 x 50 x 50)cm
24" x 20" x 31.5"
(60 x 51 x 80)cm
Chamber Volume
2.8 cu. ft. (80 liters)
5.3 cu. ft. (150 liters)
8.7 cu ft (245)
24.4" x 20.5 x 27.4
(62cm x 52cm x
69.5cm)
28.3" x 24.4" x 31.1"
(72cm x 62cm x
79cm)
28.3" x 24.4 x 40.2"
(72 x 62 x 103) cm
Power Requirements
Shipping Weight
120VAC, 50/60 Hz, single phase (220V available)
134 lb (61 kg)
167 lb (76 kg)
275 lb (125 kg)
WATER BATH WITH CIRCULATING PUMP: INCUMAX™
The IncuMax™ WB20C water bath incorporates a 20-liter seamless stainless steel bath and a PID
microprocessor controller for precise temperature control. It also features a circulating pump to ensure
optimum mixing and temperature uniformity. A stainless steel gable cover for operating up to 100°C is
supplied with the WB20C.
WB20C
INCUMAX™ WB20C SPECIFICATIONS
TEMPERATURE
Range
1ºC above ambient to 100ºC
Accuracy
0.1ºC
Uniformity
0.1ºC
Controller
Microprocessor
Circulation
Pump to mix water for maximum
uniformity
1200 watts
Heater
Safety Devices
Over-heating protection
Working Bath
Dimensions
19.5"W x 11.6"D x 5.9"H
(49.5W x 29.5D x 15H) cm
Outside
Dimensions
24.4"W x 13.4"D x 7.3"H
(62W x 34D x 18.5H) cm
Bath Volume
20 liters
Power
Requirements
120V, 50/60 Hz, 10A (220V on
request)
Weight
29 lb (13 kg)
CIRCULATING BATHS: LOW-TEMPERATURE
The CB-212 and CB-222 are closed-loop refrigerated circulating baths ideal for direct immersion of
samples or for cooling in many laboratory equipment such as rotary evaporators, lasers and
chromatography systems. The CB-212 is a compact 9-liter bench top unit while the CB-222 is a 19.5-liter
unit mounted on casters that could be placed on a bench top or the floor. Each bath features a PID
microprocessor temperature controller for precise and stable temperature. The working temperature range
is from -25°C to 100°C. Other features include a lo w-liquid level shut off, an easy-to-read bright LED digital
display, a bath drain valve for easy cleaning and replacement of coolant, and easily removable front grille
for condenser cleaning.
CB-212 AND CB-222
CIRCULATING BATH SPECIFICATIONS
MODEL
CB-212
CB-222
-25° to 100°C
Temperature Range
±0.1°C
Temperature Stability
660 watts/2252 BTU/hr
1000 watts/3412 BTU/hr
Maximum Pump Flow
9L/min
25L/min
Pump Pressure
3 PSI
5 PSI
Bath Capacity
9 liters
19.5 liters
Bath Dimensions
7.9"W x 11.8"D x 5.9"H
20W x 30D x 15H cm
11.8"W x 14.2"D x 7.1"H
30W x 36D x 18H cm
Bath Opening
7.9"W x 5.9"D x 5.9"H
20W x 15D x 15H cm
11.8"W x 8.3"D x 7.1"H
30W x 21D x 18H cm
Cooling Capacity at 20°C
Overall Dimensions
Power Requirements
Shipping Weight
11.8"W x 17.7"D x 24.8"H 15.7"W x 20.9'D x 31.5"H
30W x 45D x 63H cm
40W x 53D x 80H cm
120V, 50/60Hz, 12A
220V, 50/60Hz, 12A
80 lb/37kg
143 lb/65kg
TUBE SEALER: CRYOPROOF™ 313
Manufacturers of microtubes do not recommend storing them under cryogenic conditions because of the
potential of liquefied nitrogen seeping into the tube through the cap. Current methods manually encase the
entire tube in a heat shrink tubing using a heat gun.
The CryoProof 313 is an innovative and patented tube sealer that automatically heat shrinks a short plastic tubing to
seal only the cap of a cryogenic tube, and assures a leak-proof seal in seconds. The seal reduces the potential loss of
valuable the samples during cryogenic storage arising from very cool air or liquid nitrogen seeping into the tube, or the
release of hazardous samples from the tube.
The CryoProof sealing process is microprocessor controlled, and involves simply
placing the tube into a holder, putting a heat shrink tubing over the cap, and pressing
a button. A beam of hot air shrink wraps the tubing around the cap as the rotating
tube to form a seamless and uniform seal. The temperature of the hot air from the
CryoProof is controlled precisely and the beam is focused only on the rotating cap.
The result is a more consistent and reliable seal compared to manual sealing using
a heat gun and crimping the hot ends of the plastic tubing. By sealing the cap and
not the entire tube, you still can place the tubes in their regular racks for easy
storage and identification after sealing.
CRYOPROOF™ 313 TUBE SEALER SPECIFICATIONS
MODEL
CRYOPROOF 313
TEMPERATURE
Controller
PID microprocessor temperature controller with auto tuning
Accuracy
±0.1°C
Display
LED
HEATING TIME
Range
5 to 15 seconds
Control
Microprocessor controlled
Display
LED
SEALING
Method
Microprocessor-controlled heat shrinking of plastic
tubing with narrow hot-air stream and simultaneous 360° tube rotation
Temperature
Programmability
Up to 300°C
Seals up to 30 tubes sequentially
Various
TUBE SIZES
800 watts
HEATER
SAFETY FEATURES
Over-Temp. Protection
Safe Cool Down
Emergency Stop Key
Safety Cage
Power cutoff to the heater in case of over-heating
Internal fan cools down the system after the process, even in the event of a power failure
Process terminates when this key is pressed
Minimizes the potential for burns
OVERALL DIMENSIONS
10.5"W x 13.2"D x 11.9"H (267 x 335 x 302) mm
POWER
120VAC, 50/60 Hz, single phase (220V available)
WARRANTY
1 year
INCUBATOR SHAKER ACCESSORIES
Optional accessories include platforms, clamps, full and custom spring racks, microtiter plate holders and
additional shelves. Platform holes are drilled to accommodate the different clamps purchased. Spring racks
are designed for holding tubes in a horizontal, angled, or upright position. They can also be used to hold
flasks up to 1-liter without clamps. The racks consists of a 2-tier grid of stainless steel springs. The distance
between the two grids is adjustable so as to accommodate tubes and flasks of different heights. The spring
racks are fastened onto the platform by four screws. Custom spring racks (photo above) allow for a
combination of large flasks, microtiter plates and tubes on a given platform.
Holders for Tube Racks and Plates
Full Size Spring Rack
Platform with Custom Spring Rack
WATER BATH SHAKER ACCESSORIES
Optional accessories include clamps, stainless steel and acrylic gable covers, spring racks, platforms
(standard in GYROMAX 939 and 939XL) and cooling coils for piping in circulating cold water into the bath.
The spring rack mounts on the platform, and consists of a 2-tier grid of stainless steel springs attached to
holes on opposite sides of the rack. It is used to hold flasks up to 1-liter without the need for clamps and for
holding tubes of various diameters and heights in a horizontal, an angled, or an upright position.
Stainless Steel/Acrylic Gable Covers
Platform/Spring Rack
Flask Clamps
HYBRIDIZATION OVENS ACCESSORIES
A rotisserie with three 40mm x 300mm bottles is included with each oven. Two optional tube rotisseries can
accommodate 16 x 50-mL, or 24 x 15-mL, or 32 x 1.5/2.0-mL tubes or 96 micro-tubes are available.
Standard rotisserie with bottles & 50-, 15- and
1.5 mL tubes (clips for tubes not included)
Rotisserie for 96 Microtubes

Amerex Instruments Catalog-NA

Transcription

Similar documents

8 ways to beautify

$945,000 - Jonesboro Real Estate

kik-step®

InStyle Magazine - The Fiske Group

Frame Collection ``What is your flavor`

COMPANY SNAPSHOT

parkpoint health club - Santa Rosa Chamber of Commerce

Garnet - Oasis Homes

Congratulations to our 2013 Golf Champs, team `Zoom Zoom` from