BenQ PROJECTOR CEILING MOUNT GUIDE

BenQ PROJECTOR
CEILING MOUNT GUIDE
SAFETY INSTRUCTIONS
1.
Follow the instructions in this menu when installing the projector with this bracket. Improper or inadequate
installation could cause the projector to fall and injure someone.
2.
Make sure the installation is secure enough to bear the weight of all the devices, and also is secure enough to
withstand the vibration.
3.
Use only the parts provide with the bracket, and any parts (commercially available) that are specified in this
manual.
4.
Do not modify the bracket or the parts provided with the bracket.
5.
Do not use damaged parts. If any parts become damaged, contact your dealer.
6.
All bolts and screws must be tightened securely.
7.
Make sure not to block any ventilation openings when installing the projector.
8.
Do not install the projector in a location that is subject to high levels of dust or humidity.
9.
Do not install the projector in a location that is exposed to direct sunlight or in a location that is subject to
extreme fluctuations in temperature (such as near an air conditioner).
10.
Clean only with a dry cloth.
11.
Special techniques and experience are required when installing the projector with this bracket. Contact your
dealer to install the projector for you.
12.
Once the projector is installed, safety checks should be conducted on a regular basis.
TABLE OF CONTENTS
Packing Parts List.................................................................................................................................................................... 2
Projector Installation and Throw Distance Chart ............................................................................................................ 3
Install the Projector with Ceiling Bracket.......................................................................................................................... 4
Adjust the Ceiling Bracket .................................................................................................................................................... 7
Specifications and Drawing ................................................................................................................................................... 9
BenQ Projector Ceiling Mount Guide
PACKING PARTS LIST
✓
CEILING ADAPTER
✓
U-PLATE
✓
TUBE
✓
PIPE
✓
PIPE-BASE
✓
H – ADJUST ADAPTER
✓
PROJECTOR ADAPTER
✓
V – ADJUST BOLT
✓
NUT x 7
✓
WASHER x 1
✓
M4 SCREW x 10
✓
BOLT x 6 (TUBE BOLT x 2 , L – ADJUST
BOLT x 2 , PIPE BOLT x 2 )
Names of Parts
U - PLATE
CEILING ADAPTER
TUBE
TUBE BOLT x 2
L-ADJUST BOLT x 2
PIPE
PIPE BOLT x 2
H - ADJUST ADAPTER
V – ADJUST BOLT
PIPE BASE
PROJECTOR ADAPTER
2 Pack Parts List
BenQ Projector Ceiling Mount Guide
PROJECTOR INSTALLATION AND THROW DISTANCE
CHART
Throw Distance Chart
Diagonal (in)
30
40
50
60
70
80
90
100
125
150
175
200
225
250
275
300
Diagonal (in)
4: 3 Aspect Ratio Screen
Screen Width
Screen Height
Min Throw
(cm)
(cm)
Distance (cm)
61
46
99
81
61
131
102
76
164
122
91
197
142
106
230
162
122
263
183
137
296
203
152
328
254
190
411
305
228
493
355
266
575
406
304
657
457
342
739
508
380
821
558
418
903
609
456
1000
Screen Width
Screen Height
MinThrow
(cm)
Distance (cm)
(SW x 1.618)
Max Throw
Distance (cm)
120
160
200
241
281
321
361
401
501
601
702
802
902
1002
1103
1203
Max Throw
Distance (cm)
(SW x 1.975)
Ceiling
Throw Distance
Throw Distance
Projector Installation and Throw Distance Chart 3
BenQ Projector Ceiling Mount Guide
INSTALL THE PROJECTOR WITH CEILING BRACKET
Overview
■
■
Whole set diagram
Ceiling Mount Device
Installation Procedure
Insert U-PLATE into CEILING ADAPTER, and tighten 2 M4 screws (from the bottom) into
STEP A
the screw holes. Then mount the top part to the wall.
U-PLATE
CEILING ADAPTER
M4 screws
Ceiling mount screws
(These are not included)
4 Install the Projector with Ceiling Bracket
BenQ Projector Ceiling Mount Guide
STEP B
Install the TUBE and the U-PLATE with 2 sets of bolt & nut (TUBE BOLT).
NUT x 2
TUBE BOLT x 2
TUBE
STEP C
Install the PIPE and the TUBE with 2 sets of bolt & nut (L-ADJUST BOLT).
NUT x 2
L-ADJUST BOLT x2
PIPE
STEP D
Install the base-assembly.
STEP D1 Install the PIPE-BASE to H-ADJUST
STEP D2 Combine V-ADJUST ADAPTER and
ADAPTER with 2 M4 screws.
PROJECTOR ADAPTER with one set of V-ADJUST
BOLT & WASHER & NUT. Then tighten the M4
screws on both sides.
M4 screw
H-ADJUST ADAPTER
NUT
M4 screw
WASHER
V-ADJUST ADAPTER
M4 screw
PIPE-BASE
V-ADJUST BOLT
Install the Projector with Ceiling Bracket 5
BenQ Projector Ceiling Mount Guide
STEP E
Assemble BASS-ASSEMBLY & PROJECTOR set.
STEP E2 Assembly
STEP E1 Sliding
STEP F
Assemble BASE-ASSEMBLY and ceiling mount device with 2 sets of bolt & nut (PIPE BOLT).
Two persons are required for the completion of this step.
Ceiling mount device
NUT
BASE-ASSEMBLY
PIPE BOLT
Installation finished.
6 Adjust the Ceiling Bracket
BenQ Projector Ceiling Mount Guide
ADJUST THE CEILING BRACKET
Height Adjustment
1.
Make sure to un-install the projector first.
2.
Loosen the 2 sets of nuts connecting to L-ADJUST BOLT.
3.
Remove the L-ADJUST BOLT from the PIPE.
4.
Determine the correct position in accordance with the height of
the screen. The height adjustment ranges between 225mm and
555mm ~ 765mm with a unit of 30 mm.
5.
Insert back the L-ADJUST BOLT into PIPE, and then tighten the
previous 2 sets of nuts.
Maximum Height (non-adjustable)
Minimum Height (non-adjustable)
Install the Projector with Ceiling Bracket 7
BenQ Projector Ceiling Mount Guide
Horizontal Angle Adjustment
1.
Loosen the 2 sets of screws which are connecting
PIPE-BASE and H-ADJUST ADAPTER.
2.
Determine the correct horizontal angle in
accordance with the direction of the screen.
3.
Tighten the previous 2 sets of screws which are
connecting PIPE-BASE and ADJUSTING ADAPTER.
4.
The total swivel angle is +/-30 degrees.
Vertical Angle Adjustment
1.
Loosen the 2 sets of screws which are connecting H-ADJUST
ADAPTER and PROJECTOR ADAPTER.
2.
Determine the correct vertical angle in accordance with the
direction of the screen.
3.
Tighten the previous 2 sets of screws which are connecting
H-ADJUST ADAPTER and PROJECTOR ADAPTER.
4.
The total tilt angle adjustment is –5~+15 degrees.
8 Specifications and Drawing
BenQ Projector Ceiling Mount Guide
SPECIFICATIONS AND DRAWING
Specifications
Adjustment Range
Height
225mm, 555mm, 585mm, 615mm, 645mm, 675mm, 705mm, 735mm and 765mm.
Horizontal angle –30 ~ +30 degrees
Vertical angle
-5 ~ +15 degrees
Weight
3 kgw
Loading
4 kgw
Drawing
■
Left View
■
Front view
■
Right view
Install the Projector with Ceiling Bracket 9