Parts and Accessories Installation Instructions

Transcription

Parts and Accessories
Installation Instructions
INFO
4
1
5
2
3
TONE SELECT
6
FM
AM
MENU
MODE
053 0001 B
On-board monitor and navigation system retrofit kit
(wide screen monitor)
BMW X5 (E 53)
These installation instructions are only valid for cars with SA555 high on-board computer.
Specialist and electrical knowledge required.
The installation time is 7.5 hours but this may vary depending on the condition of the car and
the equipment in it.
Retrofit/Installation kit No.
65 90 0 136 497
Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet)
Issue date: 09.2001
Installation Instructions No. 01 29 0 136 499
Contents
Section
Page
1.
Important information on installing the on-board monitor and the navigation system . . .1
2.
Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
3.
Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
4.
Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
5.
Installation and cabling diagram for the on-board monitor wiring harness . . . . . . . . . . .9
6.
To prepare the module holder in the instrument panel
for the installation of the on-board monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
7.
To install the on-board monitor wiring harness and the on-board monitor in cars with
a production date before 10/00 (cars without a new generation radio connection plug) 14
8.
a production date after 10/00 (cars with a new generation radio connection plug) . . .19
9.
To install the on-board monitor radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
10. To install the audio module holder (only required in cars without an audio module holder) . 27
11. To install the navigation system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
12. Coding and concluding work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
13. Connection description for TV function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
14. Circuit diagram for the on-board monitor wiring harness . . . . . . . . . . . . . . . . . . . . . . .33
Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
Important information on the installation of the on-board monitor and navigation
system
For use within the BMW dealership organisation only.
The on-board monitor and the navigation system may only installed by a specialist workshop
which has available the necessary special tools and the manuals (maintenance, repair,
diagnostics, etc.).
On cars with a production date after 10/00 (cars with a new generation radio connection
plug), which have standard telephone preparation, a standard telephone or a standard
retrofit telephone the retrofit switch module kit, installation instructions 01 29 0 136 390
must also be installed before the installation of the on-board monitor and navigation
system retrofit kit."
When installing cables/leads ensure that they are not kinked or damaged.
Any additional cables/leads you install should be secured where necessary with cable ties.
Item numbers refer only to the diagrams and to the texts next to the appropriate figure.
All work is shown on a LHD car.
Proceed in exactly the same way on RHD cars.
Electrical knowledge required.
The on-board monitor radio / CD changer control cable is not supplied with the installation
kit and must be ordered separately for cars with a CD changer without a DSP amplifier using
the electronic parts catalogue (EPC) ."
The existing aerial amplifier must be replaced on cars with a production date after 10/00
(cars with a new generation radio connection plug) with an aerial amplifier for cars with a
production date before 10/00 (cars without a new generation radio connection plug). This
aerial amplifier is not supplied with the installation kit and must be ordered separately to
match the car’s equipment using the electronics parts catalogue (EPC). "
Subject to technical modifications
Required tools and equipment
MoDIC III or DIS
1/2 inch socket set
1/4 inch socket set
Set of Torx socket
Set of Philips screwdrivers
Set of flat screwdrivers
Set of Phillips screwdrivers, short
Angle drill
Set of drill bits
Conical countersink
Crimping pliers (for butt-joint connectors)
Cable lamp
Angle cutter
Universal knife
Pneumatic saw
Oscillating saw
Flat files
Combination pliers
Torque wrench
Textile adhesive tape
Extraction unit
Hot air blower
Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
EN/1
1.
Preparations
Print out the error memory
Disconnect the battery
Remove the décor strip next to the steering column
Remove the décor strip above the glove compartment
Unclip the radio compartment flap (no longer required)
Remove the radio (no longer required)
Remove the control (no longer required)
Remove the centre fresh air grille
Remove the air conditioning control
Remove the instrument cluster
Remove the left front seat
Remove the heating / ventilation duct under the left front seat
Remove the centre seat belt mounting on the rear seat
Remove the rear seat bench
Remove the left side section of the rear seat backrest
Remove the door sill strips at the front and rear left
Remove the bottom section of the B pillar trim on the left
Remove the rear left centre console
Remove the front left centre console
Remove the pedal trim (LHD cars only)
Remove the bottom left instrument panel trim (LHD cars only)
Remove the glove compartment (RHD cars only)
Remove the left footwell trim (RHD cars only)
Release the left instrument panel near the air conditioning control
Remove the right footwell trim (LHD cars only)
Remove the front right door sill strip (LHD cars only)
Remove the bottom right A pillar trim (LHD cars only)
Remove the front right centre console trim (LHD cars only)
Remove the bottom left A pillar trim (RHD cars only)
Remove the rear footwell light
Raise the carpet at the left
Remove the boot luggage net and blind
Release the C pillar trim on the left
Remove the boot lid on the both sides
Remove the mounting for the warning triangle
Remove the roller supports for the load floor on both sides (if fitted)
Remove the load edge trim
Remove the D pillar trim on the left
Remove the ventilation grille on the left.
Remove the ventilation grille holder on the left
Remove the boot floor trims on both sides (if fitted)
Remove the boot carpet (if fitted)
Remove the spare wheel cover (if fitted)
Remove the left boot trim
Remove the rear side member supports on both sides
Remove the spare wheel
TIS
instruction
No.
12 00 ...
51 16 221
51 16 221
51 16 221
65 11 030
65 81 010
64 22 161
64 11 749
62 21 000
52 14 000
52 26 005
52 26 005
52 26 008
51 47 000
51 43 150
51 16 204
51 16 200
51 45 185
51 45 180
51 16 360
51 45 181
51 45 181
51 47 000
51 43 075
51 16 200
51 43 075
63 31 023
51 43 251
51 47 172
51 46 050
51 43 252
51 37 261
51 37 261
51 47 101
51 47 151
51 46 050
-
EN/2
1.
.
Preparations
Remove the chock mounting
Release the air supply system for the pneumatic suspension and push it
forwards (if fitted)
Remove the multi-purpose tray cover under the spare wheel
Remove the top interior boot lid trim
Remove the side interior trims on both sides of the boot lid
Take the rear spoiler off the top outside of the boot lid
TIS
instruction
No.
37 22 540
51 49 056
51 49 053
51 71 412
EN/3
2.
Parts list
0
1
3
2
5
6
4
9
7
8
INFO
1
4
2
5
3
6
FM
AM
TONE SELECT
MENU
MODE
10
11
12
13
14
15
053 0002 B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
On-board monitor wiring harness
Aerial extension for GPS aerial
GPS aerial
Top on-board monitor holder
Left on-board monitor holder
Right on-board monitor holder
Self-tapping screw 3.5x6.5 (3x)
Fillister head screw M3x8 (4x)
On-board monitor complete (wide screen)
On-board monitor trim
Double insulation-piercing connector (3x)
Speed nut 4.2 mm (2x)
Fillister head self-tapping screw with washer 4.2x19 (x2)
Hexagonal nut with washer M6 (6x)
On-board monitor radio
EN/4
2.
Parts list
0
0
0
16
17
19
18
20
21
28
22
23
29
24
30
25
26
31
32
27
33
053 0003 B
0
0
0
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Amplifier holder
Front base holder
Rear base holder
Navigation computer holder
Navigation computer
Hexagonal nut with washer M5
Hexagonal screw with washer M5x14 (9x)
Speed nut M5 (8x)
Hexagonal screw with washer M6x12 (3x)
Rubber grommet (2x)
Removal bar (2x)
Cable tie (20x)
Protective strip (3x)
Butt-joint connector (7x) (for cable cross-section 0.2 – 0.5 mm 2)*
Butt-joint connector (10x) (for cable cross-section 0.75 -1.0 mm 2)*
Butt-joint connector (4x) (for cable cross-section 1.5 -2.5 mm 2)*
Hose (20x) *
Fabric tape *
The parts marked with an asterisk (*) are only required for cars with a production date
after 10/00 (cars with a new generation radio connection plug).
EN/5
3.
Connection diagram
0
A8
A7
A5
A9
A12
A13
A14
A15
A10
A6
A4
A11
A
A3
A2
A16
A1
A17
A21
A20
A24
A18
A19
A22
A23
Item
Cable
colour
Description
-
A
A1
A2
A3
Blue 12-pin socket casing
White 12-pin socket casing
Black 17-pin plug casing
A4
Reversing light socket contact terminal blue/yellow
A5
Free cable end
brown/red
A6*
TAA socket contact terminal
black/white
A7
Coaxial socket casing
black
A8
black
A9
black
A10
A11
Cable eyelet, 6 mm in diameter
Angled coaxial socket casing
brown
black
F 53 0714 B
Connection location in the car
To blue 12-pin plug casing on the on-board monitor (9)
To white 12-pin plug casing on the on-board monitor (9)
Cars with a production date before 10/00
To radio connection plug X18126
Cars with a production date after 10/00 to be cut
To black 54-pin light module connection plug X10117 in
PIN38; if PIN38 is occupied cut off the socket contact
and connect the free cable end to the supply cable,
blue/yellow cable, PIN38 on the black 54-pin socket
casing X10117 on the light module using a double
insulation-piercing connector.
To the supply cable, brown/red cable, PIN1 on the blue
26-pin socket casing X10114 on the instrument cluster
using a double insulation-piercing connector
To white 18-pin instrument cluster connection plug
X10113 in PIN3; if PIN3 is occupied cut off the socket
contact and connect the free cable end to the supply
cable, black/white cable, PIN3 on the white 18-pin
socket casing X10113 on the instrument cluster using a
double insulation-piercing connector.
To the coaxial plug casing on the aerial amplifier above
the left wheel arch
To be laid to the installation location of the left TV
amplifier above the left wheel arch and tied back
To the coaxial socket casing on the aerial amplifier
above the left wheel arch
To earth post X13016 after the left wheel arch
To be laid to the installation location of the right TV
amplifier above the right wheel arch and tied back
EN/6
3.
Connection diagram
Item
Cable
colour
Description
A12
A13
Black 17-pin socket casing
10-pin socket casing
-
A14
black
A15
A16
Black angled coaxial socket casing
(aerial connector)
Angled coaxial socket casing
White 18-pin socket casing
black
-
A17
-
A18
Blue 18-pin plug casing
-
A19
black
A20
black
A21
Black 6-pin plug casing
-
A22
A23
A24
(with “Navi” sticker)
Bordeaux 18-pin socket casing
(with “Navi+TV” sticker)
-
To the on-board monitor radio (15)
To be clipped into the black 17-pin socket casing A12
and connected with it to the on-board monitor radio (15)
To the coaxial plug casing on the on-board monitor (15)
(aerial connector)
To the coaxial plug casing on the on-board monitor (15)
To be tied back on the on-board monitor wiring harness
A with a cable tie
To branch A18, blue 18-pin plug casing on the on-board
monitor wiring harness A
To branch A17, blue 18-pin socket casing on the onboard monitor wiring harness A
A with a cable tie
A with a cable tie
If the car is fitted with a basic interface telephone 2
(BIT2), connect to the black 6-pin socket casing on the
basic interface telephone 2 (BIT2) wiring harness.
If the car is not fitted with a basic interface telephone 2
(BIT2), insulate and tie back.
To blue 18-pin plug casing on the navigation computer
(20)
To Bordeaux 18-pin plug casing on the navigation
computer (20)
A with a cable tie
EN/7
3.
Connection diagram
0
B
B1
B2
F 53 0803 B
0
Item
B
B1
B2
Cable
colour
Description
Aerial extension for GPS aerial
black
black
To GPS aerial (3)
To the navigation computer (20)
EN/8
4.
Installation and cabling diagram for the on-board monitor wiring harness
0
A11
A4
RHD A5
RHD A6
A3
A19
A2
A1
A
A16
A20
A17+A18
A12
A15
A13 A14
A10
A6
A5
RHD A4
A7
A9
X13016
A22
A23
A21
A24
A8
053 0004 B
The on-board monitor wiring harness A is to be laid along the audio or main wiring harness and
secured with cable ties as shown in the figure.
When installing the on-board monitor wiring harness A, start at the earth post X13016
above the left wheel arch.
Screw branch A10 to earth post X13016 above the left wheel arch
Lay branch A8 to the intended installation location for the left TV amplifier above the left wheel
arch and tie it back (only to be connected if you are also installing a video module and the TV
amplifier)
Branch A21 to the installation location of the telephone in the rear left side part
Branches A22 to A24 to the installation location of the navigation computer in the rear left side
part
Branches A11 to A20 along the closing panel from the left to the right side of the car
Lay branch A11 to the intended installation location for the right TV amplifier above the right
wheel arch and tie it back (only to be connected if you are also installing a video module and the
TV amplifier)
Branches A16 to A20 to the intended installation location of the video module in the multipurpose tray below the spare wheel and tie it back (only to be connected if you are also installing
a video module and TV amplifier)
Branch A12 to A15 to the installation location of the on-board monitor radio in the multi-purpose
tray under the spare wheel
Branches A7 and A9 to the aerial amplifier above the left wheel arch
EN/9
4.
Installation and cabling diagram for the on-board monitor wiring harness
The on-board monitor wiring harness A runs along the main wiring harness in front of the
rear seat bench to the cardan tunnel and from there to the left of the cardan tunnel towards
the front behind the instrument panel to the installation location of the on-board monitor
where it is fastened with cable ties or textile adhesive strip. "
Branches A1 to A3 to the installation location of the on-board monitor in the instrument panel
Branch A4 to the installation location of the light module in the A pillar on the bottom right in
LHD cars or on the bottom left in RHD cars
Branches A5 and A6 to the installation location of the instrument cluster in the instrument panel
Tie back any excess lengths.
EN/10
5.
To prepare the module holder in the instrument panel for the installation of
the on-board monitor
0
0
The figure shows the radio module holder in the
instrument panel."
41
Cut the radio module holder (40) at the marked
places using a pneumatic saw and remove the
area shaded grey (41).
40
When sawing with the pneumatic saw or the
oscillating saw, extract the chips with a dust
extractor and take care that you do not
damage anything in the car (instrument panel,
cables, heating box, etc.). It is essential to
keep to the following work sequence."
F 53 0716 B
0
The figure shows another cut in the radio
module holder on the left. Proceed in exactly
the same way on the right."
40
42
Cut out the area shaded grey on the radio module
holder (40) with an oscillating saw.
a
Dimension a = 6.5 mm
41
As you remove this section ensure that only the
lateral rib (42) on the rear strut (41) is cut to
dimension a.
053 0040 B
0
0
40
Mark the parts on the radio module holder (40) that
you wish to remove at the top with dimensions a
and b.
Then, using an oscillating saw, cut into the marked
places at the side and carefully break them off with
pliers.
Dimension a = 20 mm
Dimension b = 7.5 mm
a
b
b
053 0041 B
0
0
41
a
Mark the reinforcement (40), area shaded grey, on
the radio module holder (41) with the dimension a
and remove it with an oscillating saw.
a
Dimension a = 15 mm
40
053 0042 B
EN/11
5.
To prepare the module holder in the instrument panel for the installation of the on-board monitor
0
41
Before you install the holder for the on-board
monitor, carefully remove the reinforcements (40)
shaded grey on the radio module holder (41) on
the right with an oscillating saw.
40
053 0005 B
0
41
Carefully remove the reinforcements (40) shaded
grey on the radio module holder (41) on the left
using an oscillating.
After removing the reinforcement (40) all the
cuts on the radio module holder (41) are to be
deburred with a file."
40
053 0006
0005 B
0
41
40
4
Place the top on-board monitor holder (4) into the
removed radio module holder (40) (push it right to
the back).
Mark the three mounting points (41) from below
and remove the top on-board monitor holder (4)
again.
Carefully drill the marked mounting points (41) in
the radio module holder (40) with an angled drill
using a 3.5 mm drill bit.
Then slightly countersink the three holes from
above.
053 0007 B
0
7
40
Insert the top on-board monitor holder (4) and
secure it to the radio module holder (40) with three
self-tapping screws 3.5 x 6.5 mm (7) using a
torque of 2Nm from above.
4
053 0008 B
EN/12
5. To prepare the module holder in the instrument panel for the installation of the on-board
monitor
0
0
4
41
12
12
Carefully cut the cross strut (40) off the radio
module holder (41) along the top on-board monitor
holder (4) using an oscillating saw.
As you do so ensure that the top on-board monitor
holder (4) is not damaged.
Deburr the cross strut (40) using a file and place
the two speed nuts 4.2 mm (12) on the top onboard monitor holder (4) from below.
Then unscrew the two Philips self-tapping screws
(42) in the radio module holder (41).
40
42
053 0009 B
0
0
40
Place the left on-board monitor holder (5) and the
right on-board monitor holder (6) into the cut out
radio module holder (40).
6
5
053 0034 B
0
4
12
5
12
6
41
Secure the left on-board monitor holder (5) and the
right on-board monitor holder (6) with one fillister
head self-tapping screw with washer 4.2 x 19 (13)
each to the speed nuts 4.2 mm (12) on the top onboard monitor holder (4) and with the Philips selftapping screws (40) you removed earlier to the cutout radio module holder (41).
13
13
40
40
053 0035 B
EN/13
6.
To install the on-board monitor wiring harness and the on-board monitor in
cars with a production date before 10/00 (cars without a new generation radio
connection plug)
0
X13016
The figure shows the rear left of the boot
above the left wheel arch."
A10
Screw branch A10, cable eyelet, 6 mm in diameter
on the on-board monitor wiring harness A, to earth
post X13016 above the left wheel arch.
Lay branches A1 to A6 along the standard wiring
harness towards the front, left near the centre
console and secure it with cable ties.
A1-A6
A
F 53 0725 B
0
0
A9 40
A7
42
41
44
43
A8
A
F 53 0726 B
Unscrew the existing coaxial plug casing (40) from
the aerial amplifier (41) and tie it back (no longer
required).
Screw branch A9, coaxial plug casing on the onboard monitor wiring harness A to the released
coaxial socket casing (42) on the aerial amplifier
(41).
Disconnect the existing coaxial socket casing (43)
from the aerial amplifier (41) and tie it back (no
longer required).
Connect branch A7, coaxial socket casing to the
released coaxial plug casing (44) on the aerial
amplifier (41).
Tie back branch A8, angled coaxial socket casing
(only to be connected if you are also installing the
video module and the TV amplifier).
0
EN/14
6.
To install the on-board monitor wiring harness and the on-board monitor in cars with a
production date before 10/00 (cars without a new generation radio connection plug)
0
0
The figure shows the left footwell (LHD car),
proceed in exactly the same way on RHD
cars."
Carefully cut the carpet (40), as shown in the
figure, using a universal knife to make it easier to
lay the on-board monitor wiring harness A.
A1-A6
When you cut the carpet ensure that you do
not damage the cables/lines beneath it."
A
40
Lay branches A1 to A6 to the installation location
of the on-board monitor and secure them with
cable ties.
Lay branches A5 and A6 to the installation location
of the instrument cluster and secure them with
cable ties.
F 53 0727 B
On LHD cars lay branch A4 behind the glove
compartment to the installation location of the
light module in the A pillar on the bottom right
and secure it with cable ties.
On RHD cars lay branch A4 behind the glove
compartment to the installation location of the
light module in the A pillar on the bottom left
and secure it with cable ties.
0
28
28
A
A3
X18126
42
40 41
Connect branch A3, black 17-pin plug casing on
the on-board monitor wiring harness A, to the
existing radio connection plug X18126.
Affix a protective strip (28) to the second protective
strip (28) and then affix them to the wiring harness
so that they enclose the existing angled coaxial
socket casing (40), the black coaxial socket casing
(41) (aerial connection), the connection plug for the
control (42) and the plug connection A3+X18126.
The enclosed connections and the plug
connection are no longer required and are to be
placed behind the heating control.
053 0010 B
EN/15
6.
0
A5
A
The figure shows installation location of the
instrument cluster."
X10114
Connect branch A5, free cable end, brown/red
cable, on the on-board monitor wiring harness A,
to the DFAHL signal, brown/red cable, PIN1 on the
connection plug X10114 using a double
insulation-piercing connector (10).
A5
11
A
X10114
053 0011 B
0
A6
A
Connect branch A6, socket contact, black/white
cable on the on-board monitor wiring harness A to
the free slot PIN3 on the white connection plug
X10113.
If PIN3 on connection plug X10113 is occupied,
cut off the socket contact on branch A6 and
connect it to the tacho A signal, black/white cable,
PIN3 on the white connection plug X10113 using
a double insulation-piercing connector (11).
11
X10113
053 0012B
0
The figure shows the removed light module on
the bottom right A pillar (LHD cars), on RHD
cars proceed in exactly the same way on the
bottom left A pillar."
A4
11
X10117
40
053 0013 B
Remove the light module (40), and disconnect the
black 54-pin socket casing X10117 from the light
module (40).
Connect branch A4, socket contact, blue/yellow
the free slot PIN38 on socket casing X10117.
If PIN38 on socket casing X10117 is occupied, cut
off the socket contact on branch A4 and connect
it to the reversing light signal, blue/yellow cable,
PIN38 on socket casing X10117 using a double
Then connect socket casing X10117 and install
the light module (40) again.
Tie back any excess lengths of branch A4.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
EN/16
6.
0
40
Connect branch A1,, blue 12-pin socket casing on
the on-board monitor wiring harness A, to the onboard monitor (9).
Connect branch A2,, white 12-pin socket casing
to the on-board monitor (9).
Then insert the cables into the radio module holder
(40) and carefully slide the on-board monitor (9)
into position.
9
A2
As you insert the holder ensure that no
cables/leads are damaged."
A1
053 0036 B
0
6
5
8
8
9
The insert the trim for the on-board monitor (10) on
8
10
8
Secure the on-board monitor (9) using four fillister
head screws M3x8 (8) to the on-board monitor
holder on the left (5) and the on-board monitor
holder on the right (6).
053 0037 B
0
A22 A23
A21
A24
A
A11-A20
F 53 0733 B
The figure shows the boot at the rear left."
Lay branches A21 to A24 on the on-board wiring
harness A to the installation location of the
navigation computer.
Bei Fahrzeugen die mit Basis-Interface-Telefon 2
(BIT2) ausgestattet sind, den Abzweig A21,
schwarzes 6poliges Stiftgehäuse, mit dem
schwarzen 6poligen Buchsengehäuse des BasisInterface-Telefonkabelbaums (BIT2) zusammenstecken.
If the car does not have a basic interface
telephone 2 (BIT2), insulate and tie back branch
A21.
Lay branches A11 to A20 along the standard
wiring harness through the cable shaft on the
closing panel to the right-hand side of the car and
secure them with cable ties.
0
EN/17
6.
0
42 A13 A14
40
A15
A12
A11
Lay branch A11,, angled coaxial socket casing on
the on-board wiring harness A, along the standard
wiring harness (40) to the right wheel arch, secure
it with cable ties and tie it back (only to be
connected if you are also installing a video module
and the TV amplifier).
Lay branches A12 to A15 to the unit holder (41) in
the multi-purpose tray (42) and secure them with
cable ties.
41
A
F 53 0734 B
0
41
Lay branches A16 to A20 on the on-board monitor
wiring harness A to the unit holder (40) in the multipurpose tray (41) and secure them with cable ties.
A17/A18
A19
A20
40
A16
A
053 0014 B
EN/18
7.
To install the on-board monitor wiring harness and the on-board monitor in
cars with a production date after 10/00 (cars with a new generation radio
connection plug)
0
X13016
The figure shows the rear left of the boot
above the left wheel arch."
A10
Screw branch A10, cable eyelet, 6 mm in diameter
on the on-board monitor wiring harness A, to earth
post X13016 above the left wheel arch.
Lay branches A1 to A6 along the standard wiring
harness towards the front, left near the centre
console and secure it with cable ties.
A1-A6
A
F 53 0725 B
0
40
Disconnect the cables from the existing aerial
amplifier (40) and remove the existing aerial
amplifier (40).
Then install the new aerial amplifier for cars with a
production date before 10/00, which you ordered
separately using the electronic parts catalogue
(EPC), and connect it following procedure for its
removal in reverse.
As you connect it ensure that you do not mix
up the slots."
A
F 53 0840 B
0
A9 40
A7
42
41
43
A8
A
Unscrew the existing coaxial plug casing (40) from
the aerial amplifier (41) and tie it back (no longer
required).
Screw branch A9, coaxial plug casing on the onboard monitor wiring harness A to the released
coaxial socket casing (42) on the aerial amplifier
(41).
Connect branch A7, coaxial socket casing, to the
free coaxial plug casing (43) on the aerial amplifier
(41).
Tie back branch A8, angled coaxial socket casing
(only to be connected if you are also installing the
video module and the TV amplifier).
F 53 0839 B
EN/19
7. To install the on-board monitor wiring harness and the on-board monitor in cars with a
production date after 10/00 (cars with a new generation radio connection plug)
0
The figure shows the left footwell (LHD car),
proceed in exactly the same way on RHD
cars."
Carefully cut the carpet (40), as shown in the
figure, using a universal knife to make it easier to
lay the on-board monitor wiring harness A.
A1-A6
When you cut the carpet ensure that you do
not damage the cables/lines beneath it."
A
40
Lay branches A1 to A6 to the installation location
of the on-board monitor and secure them with
cable ties.
Lay branches A5 and A6 to the installation location
of the instrument cluster and secure them with
cable ties.
F 53 0727 B
For LHD cars
Lay branch A4 behind the glove compartment to
the installation location of the light module in the
bottom right A pillar and secure it with cable ties.
For RHD cars
Lay branch A4 behind the glove compartment to
the installation location of the light module in the
bottom left A pillar and secure it with cable ties.
0
A5
A
X10114
A5
11
The figure shows installation location of the
instrument cluster."
Connect branch A5, free cable end, brown/red
cable, on the on-board monitor wiring harness A,
to the DFAHL signal, brown/red cable, PIN1 on the
connection plug X10114 using a double
insulation-piercing connector (10).
A
X10114
053 0015 B
EN/20
7.
a production date after 10/00 (cars with a new generation radio connection plug)
0
A6
A
Connect branch A6, socket contact, black/white
the free slot PIN3 on the white connection plug
X10113.
If PIN3 on connection plug X10113 is occupied,
cut off the socket contact on branch A6 and
connect it to the tacho A signal, black/white cable,
PIN3 on the white connection plug X10113 using
a double insulation-piercing connector (11).
11
X10113
053 0016 B
0
The figure shows the removed light module on
the bottom right A pillar (LHD cars), on RHD
cars proceed in exactly the same way on the
bottom left A pillar."
A4
11
X10117
Remove the light module (40), and disconnect the
black 54-pin socket casing X10117 from the light
module (40).
Connect branch A4, socket contact, blue/yellow
the free slot PIN38 on socket casing X10117.
If PIN38 on socket casing X10117 is occupied, cut
off the socket contact on branch A4 and connect
it to the reversing light signal, blue/yellow cable,
PIN38 on socket casing X10117 using a double
40
053 0017 B
Then connect socket casing X10117 and install
the light module (40) again.
Tie back any excess lengths of branch A4.
0
40
A
Carefully remove the sheathing on the on-board
monitor wiring harness A over a length of 100 mm
behind branch A3.
Then carefully remove the sheathing on the audio
wiring harness (40) over a length of 100 mm
behind the new generation radio connector (41).
A3
41
053 0043 B
EN/21
7.
40
41
32
A3
42
30
43
33
A
PIN1
44
PIN3
PIN10
053 0018 B
The figure shows branch A3, black 17-pin plug casing on the on-board monitor wiring
harness A and the new generation radio connection plug (40) on the audio wiring harness
(41) when removed, if they are fitted, proceed in exactly the same way. "
Cut the yellow/red connection cable, RADLV+, PIN1 on branch A3 and the yellow/red
connection cable, RADLV+, PIN3 on the new generation radio connection plug (40) with an
angle cutter.
Push the hose (32) on to the cut yellow/red connection cable (42) on the on-board monitor wiring
harness A.
Then connect the cut yellow/red connection cable (42) on the on-board monitor wiring harness
A and the cut yellow/red connection cable (43) on the audio wiring harness (41) with a butt-joint
connector (30) (cable cross section 0.75-1.00 mm 2).
Push the hose (32) over the crimped butt-joint connector (30) and shrink it on with a hot air
blower.
Cut the black/white connection cable, tacho A signal, PIN10 on branch A3 with an angle cutter.
Put the hose (32) on to the cut black/white connection cable (44) on the on-board monitor wiring
harness A, and shrink it using a hot air blower so that the open cable end is insulated (not
required).
Then connect the remaining connection cables on branch A3 as set out in the following
following connection table to the connection cables on the new generation radio connection
plug (40).
Always complete one connection at a time since if you cut several connection cables you
might confuse them as a result of the different cable colours involved (see following
connection table). In addition. ensure that you use the appropriate butt-joint connectors for
the various cable cross-sections."
When you have made all the connections, first wrap each individual connection and then all the
connections in the fabric tape (33) (cut branch A3 is no longer required).
EN/22
7.
Connection table (on-board monitor wiring harness to the audio wiring harness)
40
X18126
X18805
1
5
9
13
2
6
10
14
3
7
11
15
4
8
12
16
4
3
2
1
2
1
6
3
8
7 8 9 10 1112
7 8 9 10 1112
5
X13598
X13321
9
7
X18126
1 2 3 4 5 6
14
17 12
4
1 2 3 4 5 6
11
15
13
10 16
A3
F 53 0843 B
New generation radio connection plug (40) on Branch A3 on the on-board monitor wiring
the audio wiring harness
harness
X18805
PIN
Signal
X18126
Crosssection
Cable colour
PIN
Signal
Cable colour
Crosssection
0.75 mm2
1
RADLV+
GERT
0.75 mm2
mm2
6
RADRH+
BLSW
0.75 mm2
0.75 mm2
2
RADRV+
BLRT
0.75 mm2
mm2
3
RADLH+
GESW
0.75 mm2
0.75 mm2
14
RADRH-
BROR
0.75 mm2
BLBR or BROR
0.75
mm2
11
RADRV-
BROR
0.75 mm2
RADLV-
GEBR or BROR
0.75 mm2
8
RADLV-
BROR
0.75 mm2
RADLH-
GEGR or BROR or free
mm2
12
RADLH-
BROR
0.75 mm2
3
RADLV+
GERT
1
RADRH+
BLVI or BLSW or free
0.75
2
RADRV+
BLRT
4
RADLH+
GEVI or GESW or free
0.75
5
RADRH-
BLGR or BROR or free
6
RADRV-
7
8
0.75
X18126
X18126
9
I/K bus
WSGRGE
10
TELM
WSBR
0.35 mm2
7
I bus
WSGRGE
0.35 mm2
mm2
4
TELM
WSBR
0.35
0.35 mm2
13
ANT
WS
14
58G
GRRT
0.50 mm2
16
ANT
WS
0.50 mm2
mm2
13
58G
GRRT
0.50
0.50 mm2
15
30<64
RTGN
2.50 mm2
9
30<64
RTGN
2.50 mm2
mm2
16
R<E
VIWS
5
R<E
VIWS
1.50 mm2
1.50
Colour abbreviations
BR
RT
VI
WS
GR
=
=
=
=
=
Brown
Red
Violet
White
Grey
SW
GN
GE
BL
OR
=
=
=
=
=
Black
Green
Yellow
Blue
Orange
EN/23
7.
0
0
X13321
40
Disconnect the white 12-pole connector X13321
from the new generation radio connection plug
(40).
Then cut the remaining connection cables on the
new generation radio connection plug (40) with an
angle cutter and insulate the open cable ends (the
cut-off new generation radio connection plug (40)
is no longer required).
40
A
40
053 0019 B
0
40
28
28
A
X13321
Affix one rattle guard (28) on to the second rattle
guard (28) and then affix them to the wiring
harness so that the angled Fakra plug (aerial
connector) (40), the connection plug for the control
(41), connection plug X13321 and the wrapped
connections (42) are enclosed in them.
The wrapped connections (40, 41 and X13321)
and the wrapped connectors (42) are no longer
required and should be placed behind the heating
system control.
41
42
053 0020 B
0
0
40
Connect branch A1,, blue 12-pin socket casing on
the on-board monitor wiring harness A, to the onboard monitor (9).
Connect branch A2,, white 12-pin socket casing
Then insert the cables into the prepared radio
module holder (40) and carefully slide the onboard monitor (9) into position.
9
A2
As you insert the holder ensure that no
cables/leads are damaged."
A1
053 0036 B
0
6
5
8
8
9
8
10
Secure the on-board monitor (9) using four fillister
head screws M3x8 (8) to the on-board monitor
holder on the left (5) and the on-board monitor
holder on the right (6).
The insert the trim for the on-board monitor (10) on
8
053 0037 B
EN/24
7.
0
0
A22 A23
A21
A24
A
A11-A20
Lay branches A21 to A24 on the on-board wiring
harness A to the installation location of the
On cars with a basic interface telephone 2 (BIT2),
connect branch A21, black 6-pin plug casing, to
the black 6-pin socket casing on the basic
interface telephone wiring harness (BIT2).
If the car does not have a basic interface
telephone 2 (BIT2), insulate and tie back branch
A21.
Lay branches A11 to A20 along the standard
wiring harness through the cable shaft on the
closing panel to the right-hand side of the car and
secure them with cable ties.
F 53 0733 B
0
42 A13 A14
40
A15
A12
A11
Lay branch A11,, angled coaxial socket casing on
the on-board wiring harness A, along the standard
wiring harness (40) to the right wheel arch, secure
it with cable ties and tie it back (only to be
connected if you are also installing a video module
and the TV amplifier).
Lay branches A12 to A15 to the unit holder (41) in
the multi-purpose tray (42) and secure them with
cable ties.
41
A
F 53 0734 B
0
0
41
Lay branches A16 to A20 on the on-board monitor
wiring harness A to the unit holder (40) in the multipurpose tray (41) and secure them with cable ties.
A17/A18
A19
A20
40
A16
A
053 0023 B
EN/25
8.
To install the on-board monitor radio
0
The figure shows the multi-purpose tray in the
boot."
25
If the two rubber grommets (40) are not fitted in the
unit holder (41), the two rubber grommets (25)
supplied in the retrofit/installation kit must be
fitted.
Then insert the on-board monitor radio (15) into
the rubber grommets (40/25) as shown in the
figure.
15
41
40
053 0024 B
0
A13
A14
40
A15
A12
A
On cars with a CD changer but without a DSP
amplifier, the control cable for the on-board
monitor wiring radio/CD changer must also be
fitted."
15
Secure branch cable A13 with the blue locking clip
(40).
Connect branch cable A12, black 17-pole socket
casing, to on-board monitor radio (15).
Connect branch A14, black angled coaxial socket
casing (aerial connection), to the on-board monitor
radio (14).
Connect branch cable A15, angled coaxial socket
casing, to the on-board monitor radio (15).
053 0025 B
0
28
21
22
15
A17/A18
A19
A16
A
A20
40
42
Remove the blue locking clip (40) from branch
A12, black 17-pin socket casing on the on-board
monitor wiring harness A and connect branch
A13, 10-pin socket casing, to branch A12 in the
appropriate position.
41
053 0026 B
Secure the on-board monitor radio (15) to the unit
holder (40) using the hexagonal nut with washer
M5 (21) or hexagonal screw with washer M5x14
mm (22), depending on the design of the on-board
monitor radio (15).
Affix the rattle guard (28) to the on-board monitor
wiring harness A so that branches A19 and A20,
plug connection A17+A18 and branch A16 are
wrapped in it.
Tie back the wrapped connections and the plug
connector to the standard wiring harness (41) in
the multi-purpose tray (42) (only to be connected if
you are also installing the video module and the TV
amplifiers).
EN/26
9.
To install audio module holder (only required in cars without an audio module
holder)
0
0
16
Place amplifier holder (16) on the two bottom stud
bolts (40) and the two side stud bolts (41).
41
40
053 0027 B
0
23 14
42
16
Secure the amplifier holder (16) to the stud bolts
(40) using two hexagonal nuts with washers M6
(14) and to the M6 thread (41) in the inside closing
panel (42) using a hexagonal screw with washer
M6x12 (24).
Then place two speed nuts M5 (23) on the
amplifier holder (16).
41
24
40
053 0028 B
0
0
41
23
17
42
24
40
14
Place the front base holder (17) on to the two side
stud bolts (40) and secure it to the stud bolts (40)
with two hexagonal nuts with washers M6 (14).
In addition, secure the front base holder (17) to the
thread M6 (41) in the rear left side part (42) using a
hexagonal screw with washer M6x12 (24).
Then place two speed nuts M5 (23) on the front
base holder (17).
14
053 0029 B
0
40
23
24
41
17
22
23
23
22
18
Secure the rear base holder (18) to the speed nuts
M5 (23) that you positioned earlier using four
hexagonal screws with washers M5x14 (22) and to
the thread M6 (30) in the side part at the rear left
(41) using a hexagonal screw with washer M6x12
(24).
Then place two speed nuts M5 (23) on to the front
base holder (17) and the rear base holder (18).
23
053 0030 B
EN/27
10. To install the navigation system
0
0
40
3 40 42
The figure shows the tailgate under the rear
spoiler from the outside."
Put GPS antenna (3) on the two stud bolts (40) on
the boot lid (41) and secure it with two hexagonal
nuts with washers M6 (14).
Thread the connection cable (42) for the GPS
aerial (3) through the opening in the tailgate (41)
into the interior of the car and fit the rubber
grommet (43).
41
43
14
14
053 0031 B
0
B
B1 40
43
41
Connect branch B1, coaxial plug casing on the
aerial extension for the GPS aerial B to the coaxial
socket casing (40) on the connection cable (41) for
the GPS aerial.
Then thread the aerial extension for the GPS aerial
B with branch B2, coaxial socket casing, through
the rubber grommet (42), as show in the figure,
into the interior of the car and secure it with textile
adhesive tape (43).
B2
42
F 53 0739 B
0
0
B
Lay the aerial extension for the GPS aerial B with
branch B2, coaxial socket casing, along the
standard wiring harness as shown in the figure to
the installation site of the navigation computer in
the boot at the rear left and secure it with textile
adhesive tape or cable ties.
B2
F 53 0847 B
EN/28
10. To install the navigation system
0
19
23
B
23
A
A24
A23
A22
22
22
Secure the navigation computer holder (19) to the
four speed nuts M5 (23) you inserted previously
using four hexagonal screws with washers M5x14
(22).
Thread branches A22 and A24 blue 18-pin socket
casing, and branch A23, Bordeaux 18-pin socket
casing on the on-board monitor wiring harness A,
from the rear through the navigation computer
holder (19).
Tie back branch A24, with the sticker "NAVI+TV"
on branch A22, with the sticker "NAVI" using a
cable tie.
B2
053 0032 B
Push branch cable B2, coaxial socket casing, on
the aerial extension for the GPS aerial B from the
rear through the navigation computer holder (19)
as well.
0
19
A22
A23
B
A
A24
B2
20
053 0033 B
Connect branch A22, blue 18-pin socket casing,
with the sticker “NAVI” and the tied back branch
A24 on the on-board monitor wiring harness A to
the navigation computer (20).
Connect branch A23, Bordeaux 18-pin socket
casing, to the navigation computer (20).
Connect branch B2, coaxial socket casing on the
aerial extension for the GPS aerial B2, to the
navigation computer (19).
When you slide in the navigation computer
(20) ensure that no cables or lines are jammed
or damaged."
Push the navigation computer (20) into the
navigation computer holder (19) until it engages.
0
EN/29
11.
Coding and concluding work
If you also wish to install the video module and TV amplifiers for TV function, the coding and
the concluding work should not be completed until after the video module and TV
amplifiers for TV function have been installed, see section 13) . "
Coding
This system requires coding.
To ensure that the retrofit system:
– is fully functional and
– does not cause malfunctions and errors in other electrical systems
this retrofit system and, possibly, other components must be coded and saved in the central
code in the IKE.
This coding process is automatic using the current coding program in the “Retrofit” path.
The process is user-guided, simply follow the text instructions for each individual step.
Procedure:
- Connect DIS/MoDIC to the car
- Switch the ignition “ON”
- Select “Coding ZCS”
– Confirm the date by pressing “Y” (MoDIC only)
- Series: “E53”
- Path: “2 Retrofit”
- System: “Navigation”
The current “Navigation CD-ROM operating software V16” is required to load the
operating system.
ImportantDo not insert the CD-ROM “Operating software” into the CD drive yet.
Do not insert the CD-ROM “Operating software” until asked to do so by the instructions
on the on-board monitor.
At the same time this CD-ROM “Operating software” also encodes the language."
- Start automatic coding (confirm with “Y”)
– Follow the instructions on the on-board monitor
- Print out the new central label for the amended coding key and affix it to the car on the righthand side of the boot near the battery.
- After the message “Coding complete” appears on the monitor of the DIS/MoDIC, switch the
ignition ”OFF”, wait for at least 10 seconds and then switch the ignition “ON” again.
- Print out the error memory
– Insert the CD-ROM “Road map” into the navigation computer
– Complete a function test
EN/30
11. Coding and concluding work
0
0
0
In vehicles with a DSP amplifier, the DSP amplifier also has to be recoded. "
Procedure:
- Connect DIS/MoDIC to the car
- Switch the ignition “ON”
- Select “Coding ZCS”
– Confirm the date by pressing “Y” (MoDIC only)
- Series: “E53”
- Path: “1 Recoding”
- System: “DSP”
- Start automatic coding (confirm with “Y”)
- After the message “Coding complete” appears on the monitor of the DIS/MoDIC, switch the
ignition ”OFF”, wait for at least 10 seconds and then switch the ignition “ON” again.
- Print out the error memory
– Complete a function test
Language coding
The language coding can be repeated using the “Navigation CD-ROM operating software”.
Concluding work
Connect the battery
Conduct a function test
Assemble the car again following the instructions to dismantle it in reverse order
Print out the error memory
EN/31
12. Connection description for TV function
0
This chapter is only applicable if the car is also to be upgraded with the TV function. "
To complete the upgrade the required parts (video module, TV amplifier and small parts) must
be ordered separately using the electronic parts catalogue (EPC) and installed.
In addition the appropriate branches of the on board monitor wiring harness A must be
connected as follows:
Undo the tied-back branch cable A8, angled coaxial socket casing on the on-board monitor
wiring harness A, and connect it on to the left TV amplifier installed previously above the left
wheel arch.
Release the tied back branch A11, angled coaxial socket casing on the on-board monitor wiring
harness A and connect it to the TV amplifier installed previously above the right wheel arch.
Disconnect branch A22, blue 18-pin socket casing with the sticker "NAVI" on the on-board
monitor wiring harness A from the navigation computer.
Release the tied-back branch cable A24, blue 18-pin socket casing with the sticker “NAVI + TV”
on the on-board monitor wiring harness A, and connect it to the blue 18-pin plug casing on the
Branch A22, blue 18-pin socket casing with the sticker “NAVI”, which you previously
disconnected, is to be tied back (not required).
Release tied back plug connection A17+A18 on the on-board monitor wiring harness A,
disconnect it and connect branch A17 , blue 18-pin plug casing on the on-board monitor wiring
harness A, to the blue 18-pin socket casing on the video module, which you previously installed
in the multi-purpose tray under the spare wheel.
Tie back branch A18, blue 18-pin plug casing on the on-board monitor wiring harness A
(no longer required).
Also release the tied back branches A19 and A20, coaxial socket casing, and branch A16, white
18-pin socket casing on the on-board monitor wiring harness A and connect it to the previously
installed video module in the multi-purpose tray under the spare wheel.
Connect branches A19 and A20, coaxial socket casings, to the two coaxial plus casings on the
video module.
Connect branch A16, white 18-pin socket casing, to the white 18-pin plug casing on the video
module.
If the car is to be upgraded to TV function at a later date, the system will have to be recoded.
For further details refer to section “12. Coding and concluding work”..
EN/32
2
8
1
LTG VERDRILLT
1393905.9
LTG VERDRILLT
1393906.9
ANT
16
N9
14
6
12
3
11
2
8
1
16
ANT
1393904.9
RADRH- RADRH+ RADLH- RADLH+ RADRV- RADRV+ RADLV- RADLV+
LTG VERDRILLT
0,5
WS
1393903.9
0,75 0,75
0,75 0,75 0,75 0,75 0,75 0,75
BROR BLSW BROR GESW BROR BLRT BROR GERT
LTG VERDRILLT
RADRH- RADRH+ RADLH- RADLH+ RADRV- RADRV+ RADLV- RADLV+
11
9
30<64
7
I-BUS
TELM
4
2,5
RTGN
-
0,35
0,35
WSBR WSGRGE
-
VB 30 RADIO VB R
0,5
GRRT
0,35
SWWS
TAA
10
R
5
1,5
VIWS
-
13
58G
0,5
GRRT
-
VB 58G
10
TAA
0,35
SWWS
-
RADIO
0,5
WSGRGE
I/K-BUS
30<64
2
30<64
1
3
8
30<64
0,5
RTGN
-
30<64
RADIO
X18802
16
0,5
BR
WS
14
5
11
VMG31
VMG
MASSE STEREO/HIFI
-
X13016
0,5
BR
6
VMB
0,35
SW
7
10
VM+
12
11
R<E
0,5
VIWS
5
VM-
RADIO
X18804
18
VM-
X18804
X18802
12
VMLC31
0,5
BRRT
X1362
0,5
SW
PL
12
1
58G
0,5
GRRT
58G
VB 58G
4
10
9
TAPER+ TAPER-
0,5
0,5
0,5
0,5
BLSW BLBR GESW GEBR
TAPEL+ TAPEL-
3
RADIO
X18801
6
7
TAPEL+ TAPEL-
1
2,5
BR
15
2
RADIO
X18805
11
DFAHL
0,35
BRRT
MASSE STEREO/HIFI
-
X13016
31E<RAD
X18126
TAPER+ TAPER-
0,5
BR
X3279
0,5
BR
31E<RAD
2 X18801
RADIO
X69990
LEITUNG
OFFEN
-
VB R
-
X229
VMLC31 PL
0,5
0,5
GERT GEBR
VM+
9
15
VMB31
0,35
SCHIRM
6
VMB31
5
VMB
4
VMG31
7
30<64
I/K-BUS
6
0,5
RTGN
0,5
WSGRGE
VB I-BUS
-
X18344
0,35
SCHIRM
31E<RAD 31E<RAD
10
VMR31
7
0,35
SW
WS
0,35
SCHIRM
VMR
WS
0,35
SW
3
VMG
2
VMR31
1
VMR
A196
0,5
0,5
RTGN RTGN
A197
0,35
SWWS
TAA
1
X18126
VB TACHO A
X229 X1362 X581
X1543
VB I-BUS
1,5
VIWS
58G
R
X18344
30<64
13
5
2,5
RTGN
I-BUS
TELM
9
0,35
WSGRGE
7
4
VIDEOMODUL
3
BORDMONITOR
1724213.9
LTG1-ADR.GESCH.
12
1724213.9
LTG1-ADR.GESCH.
6
1724213.9
LTG1-ADR.GESCH.
14
1386696.9
LTG VERDRILLT
X1543
1386699.9
VB 30 RADIO
LTG VERDRILLT
RADIO
1386698.9
X10113B
LTG VERDRILLT
RADIO
1
RS
0,35
BLGE
0,35
BLGE
RS
38
RADIO
X10117B
1
3
4
5
RXD CTS RTS TXD
2
X133185
15
GND
RTS
F 530848 B
RADIO
X1312B
3
TXD R
16 14 13 12
RXD CTS
0,5
0,5 0,5 0,5 0,5 0,75
Schirm GE SW GN BR VI/WS
GND
RADIO
1724046.9
X6500S
LTG GESCH.
RADIO/HIFI
13. Circuit diagram, on-board monitor wiring harness
0
0
0
0
0
0
EN/33
RADIO
VIWS
0,75
VIWS
1
30
0,5
RTGN
3
I-BUS
10
31
0,5
BR
VB 31
4
X3279
0,5
WSGRGE
18 17 16
8
3
12
RGBGND R75 B7S B75 SYNC VOICE VOIEGND
7
LTG GESCH.
1724046.9
R75
13
B75
0,5
0,5
BLRT BLBR
138669.7
8 17 15
9
RADIO
X1313B
18
RG
G75 SYNC BGND VOICE VOIEGND
0,5
0,5 0,5 0,5 0,5
Schirm GE SW GN BR
LTG VERDRILLT
-
1
30<64
1
2
30<64
3
I/K-BUS
1724213.9
30<64
2
I/K-BUS
3
VMR
7
VMR31
16
5
1724213.9
0,35
SCHIRM
16
VMR31
7
VMR
0,5
0,5
0,5
0,35
RTGN RTGN WSGRGE SW
30<64
LTG 1-ADRIG GESCH.
VB I-BUS
VMG
0,35
SW
1724213.9
VMG31
14
VMB
6
15
VMB31
11
0,5
BR
31E<RAD
9
11
9
18
VM-
0,5
GEBR
RADIO
X6502B
18
VM-
1386696.9
0,5
GERT
VM+
31E<RAD 31E<RAD VM+
0,5
BR
10
VMLC31
0,5
BRRT
10
31E<RAD
12
VMLC31
12
0,35
SCHIRM
15
VMB31
6
VMB
0,35
0,35
SCHIRM SW
14
VMG31
5
VMG
LTG 1-ADRIG GESCH.
X1543
X18344
VB 30
RADIO
LTG 1-ADRIG GESCH.
-
LTG VERDRILLT
VB R
ANT
2
SCHIRM
VERSTÄRKER TV
1
A453
ANT
RADIO
X13346
0,14 0,35
SW SCHIRM
2 X13348
SCHIRM
1
RG174
X229
18365553.9
A197
ANT
A197
1
2
SCHIRM
VERSTÄRKER TV
A453
1
RADIO
X13347
0,14 0,35
SW SCHIRM
2 X13349
SCHIRM
VIDEOMODUL
ANT
18365553.9
VIDEOMODUL
RG174
RADIO
1
AU
N9
2
DIVERSITY
A421
ANT-HF SCHIRM
1
RADIO
X13344
0,14 0,35
SW SCHIRM
N9
1
1
2
DIVERSITY
A421
-IIF 530748 B
RADIO
X13338
0,14 0,35
SW SCHIRM
2 X13343
SCHIRM
RADIO
ANT-NF SCHIRM
ANT-NF
ANT-HF
X13342
RADIO
18365553.9
X6501S
RG174
RADIO
RG174
18365553.9
X18806B
0
0
0
0
EN/34
Legend
Colour abbreviations
A196
On-board monitor
BR
=
Brown
A197
Video module
RT
=
Red
A421
Diversity
VI
=
Violet
A453
TV amplifier
WS
=
White
N9
Radio
GR
=
Grey
X229
R connector
SW
=
Black
X581
Tacho A connector
GN
=
Green
X1312
Navigation A
GE
=
Yellow
X1313
Navigation B
BL
=
Blue
X1362
58g connector
X1543
30 radio connector
X3279
31 connector
X6500
Adapter plug connector
X6501
Adapter cable connector
X6502
Adapter (+) plug connector
X10113 IKE 3
X10117 Light module C
X13016 Stereo/hi fi earth
X13318 Navigation system telephone
X13338 Aerial
X13342 Radio HF aerial
X13343 Radio ZF aerial
X13344 Diversity HF aerial
X13346 TV amplifier aerial, right
X13347 TV amplifier aerial, left
X13348 Video module aerial, right
X13349 Video module aerial, left
X18126 Radio
X18344 I bus connector
X18801 On-board monitor control
X18802 On-board monitor
X18804 Video module II
X18805 Radio II
X18806 Video module III
X69990 Open cable
EN/35

Parts and Accessories Installation Instructions

Transcription

Similar documents

Visit a Navy AutoSource Representative on-board

Atlantis Energy Systems Inc.

Bitron AV1407/001 (4+n) T-Line

Kenda - Bearclaw HTR - Modern Tire Company

DUCATI 748/916/996 Installation Instructions

8 Series Line Chart_611

Bticino 334202 (5 Wire)

wt waggoner building

installation

gemtor harness positioning loops