Steltronic ST-HB32 LCD 32” 16/9 Monitor User and Installation Manual

Transcription

Steltronic
ST-HB32 LCD 32” 16/9 Monitor
User and Installation Manual
Steltronic S.p.A.
Via Artigianale 34, 25082 Botticino Sera Brescia - Italy
Tel: +39 030 2190811 fax: +39 030 2190798
http://www.steltronic.com
Worldwide Service: + 39 030 2190830
Email: [email protected]
US Steltronic: +1 (909) 287-0712
[email protected]
STELTRONIC S.p.A.
Botticino Sera (BS) - ITALY
Tel +39 030 2190811 - Fax +39 030
2190798 http://www.steltronic.com
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Index
MONITOR ADJUSTMENTS and TECHNICAL SPECIFICATIONS
1.0
2.0
Monitor technical specification
OSD Screen Adjustments
Pg. 03
Pg. 05
MONITOR’S INSTALLATION
3.0
4.0
5.0
5.1
5.2
5.3
5.4
5.5
6.0
6.1
6.1
7.0
7.1
Pre-installation requirements
Monitor dimensions
Available monitor supports
Fixing the Brackets to the ceiling
Assembly the Frame for single monitor [Configuration A]
Hanging 2 near monitors [Configuration B]
Hanging 2 monitors with Central Plate [Configuration C]
Hanging 3 near monitors [Configuration D]
Connecting the Lane computer (SUPERELEX) to the monitor
Wins software settings for 16:9 monitors
Connecting the Lane computer (V.L.C.) to the monitor
Display Video signal (Superelex lane computer)
Display Video signal (V.L.C. lane computer)
Pg.
Pg.
Pg.
Pg.
Pg.
Pg.
Pg.
Pg.
Pg.
Pg.
Pg.
Pg.
Pg.
11
12
13
14
17
18
19
21
23
24
25
26
27
Pg. 2 of 28
Rev A.
June 2007
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Pg. 3 of 28
Rev A.
June 2007
[1.0] Monitor Technical specifications
[1.1] General description
ST-HB32A1X is a 32” TFT Liquid Display with 16-CCFL Backlight unit and 1-ch LVDS interface.
This display supports 1366x 768 WXGA format and can display true 16.7M colours (8-bit/color).
The inverter module for backlight is built-in.
NOTE: the monitor is not equipped with speakers and RF module for Radio Frequency TV reception.
[1.2] Features
- High brightness (500 nits)
- High contrast ratio (1200:1)
- Fast response time ( Gray to Gray average 6.5 ms)
- High colour saturation NTSC 75%
- Max resolution 1360 x 768@60 Hz
- LVDS interface
- Low colour shift function option
- Ultra wide viewing angle :176(H)/ 176(V) Super MVA technology
-Support PIP/PAP function
- Configurable ambient light sensor
- VGA/DVI input support Video sync – 720p
- OSD menu controls by Remote controller, OSD button& RS232C controller
[1.3] General Specifications
Active Area
Bezel Opening Area
Driver Element
Pixel Number
Pixel Pitch(sub-Pixel)
Pixel Arrangement
Display Colours
Display operation Mode
Surface Treatment
708.954mm(H) x 398.592mm(V) (32.02”diagonal)
714.96mm(H) x 404.6mm(V)
a-si TFT active matrix
1366 x R.G.B x 768 pixel
0.1730(H) x 0.5190(V)
RGB vertical stripe
16.7M Color
Transmissive mode / Normally black Anti-Glare coating(Haze 25%), Hard coating (3H)
[1.4] Electrical Specifications [a]
Power source Power Input
100VAC~240VAC (Worldwide)
Operation Mode
250W (Max) Power
consumption Power Saving Mode 20W(Max) W
Storage Temper.
Min -20 ~ Max60 Celsius
Operating Temper.
Min 5 ~ Max 40 Celsius
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Pg. 4 of 28
Rev A.
June 2007
[1.5] Electrical Specifications [b]
LCD PANEL:
Max.Resolution
1360 x 768@ 60Hz Brightness
500 Nits
Contrast Ratio
1200
Response time
Typ. 6.5 ms(Gray to Gray) ms
Aspect Ratio
16 :9
GRAPHIC:
Separate Sync.
Horizontal Sync.
Vertical Sync.
Input Connector
LVDS Level Positive / Negative Positive / Negative D-Sub 15 pins, DVI-D 24 pins, -
SCAN RATE:
Horizontal
Vertical
26~91 KHz
50~85 Hz
PERFORMANCE:
Auto Adjust
Screen Scaling
Power Management
Color Adjustment
OSD Language
Clock, Phase, H-Position &-V Position VGA/SVGA/XGA/WXGA - Full Screen Display
VESA DPMS, DVI DMPM User, 6500K, 5400K ,3200K & 9300K English
[1.6]Safety
This Product was tested to the following standards and found Compliance with the following standards:
FCC：CFR47 Part 15 / CISPR 22 3rd Edition：1997, Class B
ANSI C63.4. 2003
Canadian ICES-003
CE： EN 55022. 1998+A1. 2000+A2. 2003, Class B
EN 55024. 1998+A1. 2001+A2. 2003 IEC 61000-4 Series
EN 61000-3-2. 2000& EN61000-3-3. 1995+A1. 2001
UL： UL 60950-1. 2003, First Edition
CSA C22.2 No. 60950-1-03 1stEd.April 1, 2003
TUV: EN 60950-1/A11:2004
[1.7] Dimensions and weight
Dimension(w/o stand)
Net weight
Gross weight
671.2*413.2*82.32 (W*D*H) mm
16.5 KG Physical
20 KG
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Pg. 5 of 28
Rev A.
June 2007
[2.0] OSD Screen Adjustments
The monitor could be adjusted using the Remote control or directly from OSD panel accessible on rear
of the monitor. Main power switch is located on the rear of the monitor, close to the AC plug input.
Main Power
Switch
OSD
Control panel
monitor’s rear
[1] Power ON/STANDBY
1
2
1
7
[2] Enter – Activate selection
4
3
[3] Menu RIGHT
6
5
[5] Menu DOWN
2
8
[6] Menu UP
[4] Menu LEFT
3
4
9
11
5
10
6
12
[7] MENU (Exit)- Access Main Menu/submenu(Quick menu selection)
[8] EXIT (one Level UP)
[9] AUTO –Adjust clock, phase, H position,
V position automatically
[10] PIP (picture in picture)
7
[11] SOURCE (input source selection)
OSD panel
Remote Control
[12] SWITCH (PIP switch)
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Pg. 6 of 28
Rev A.
June 2007
WARNING:
The SOURCE input Selection for Scoring is VGA
The Monitor detect automatically the active Source, if the Lane computer it will be power
off/restart, monitor switch the screen on the next available source (if connected).
To switch the screen back to SCORE press vary time SOURCE button on remote control
until the VGA input will be display on OSD message.
Factory DEFAULT SETTINGS AND ADJUST RANGE
Item
Power Switch
Brightness
Contrast
Color Temperature
Red
Green
Blue
OSD Language
Auto configuration
Factory Default
OFF
80
50
User
50
50
50
English
ON
Adjust Range
ON/OFF
0 ~ 100
0 ~ 100
USER/6500K/9300K
0 ~ 255
0 ~ 255
0 ~ 255
English
ON/OFF
SUGGESTED MONITOR SETTINGS FOR STELTRONIC SCORE
[1]INPUT SOURCE
Press vary time SOURCE button on Remote control until VGA screen appear on OSD
[2] MENU DISPLAY
Press <MENU> <ENTER> <Arrow DOWN> to display the Menu; use <Arrow LEFT>
<Arrow RIGHT> for changing value.
Brightness
Hue
Flesh-Tone
60
8
OFF
Contrast
Saturation
Black Level
60
70
55
[3] MENU IMAGE
Press <MENU> <ENTER> <Arrow RIGHT> <Arrow DOWN> to display the Menu; use
<Arrow LEFT> , <Arrow RIGHT> for changing value.
Scaling
Angle Filtering
Sharpness
FILL
OFF
15
Noise Reduction
Film Mode Detect
OFF
ON
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
OSD tree menu
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Pg. 7 of 28
Rev A.
June 2007
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Pg. 8 of 28
Rev A.
June 2007
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Pg. 9 of 28
Rev A.
June 2007
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Next chapters
are for
installation crew only
Pg. 10 of 28
Rev A.
June 2007
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Pg. 11 of 28
Rev A.
June 2007
[3.0] Pre-installation requirements
MONITOR STRUCTURE
The center owner must supply an adequate support structure for hanging monitors, in compliance with
local regulations. Each monitor (including support steel but NOT chains or steel cables) weighs about
16 Kg /35.3 pounds, each lane computer (usually installed near the monitors) about: 3.5Kg / 8 pounds
The support structure in the center must be inspected and approved by authorized personnel in
compliance with local regulations.
The center owner(s) are responsible for the installation and approval of the support structure.
The support structure should be in place and approved before scoring system installation starts and
sheet approval must be shown to distributor or seller of scoring system.
ELECTRICAL INSTALLATION
Each monitor receives power from a dedicated outlet, one connector per monitor. AC input could be
powered on/off via Software*, otherwise it’s possible switch the monitors from ON to STAND-BY using
the remote control.
Each electrical line must be controlled by a dedicated magneto-thermic switch as described in the
“power supply connection” section of the Scoring Pre-installation manual.
Steltronic S.p.A. supplies one power cord for each monitor with a VDE connector on it, 1.8 meters long
(6 feet); the customer must provide one AC power outlet for each monitor at most 1.5 meters (about 4
feet) from the lane computer itself.
The customer is responsible for the installation and approval of the electrical supply used for the
scoring system. The installation of the electrical supply should be done and approved before the
scoring system is installed and sheet approval should be shown
to the seller or distributor of the scoring system.
Further information on the electrical requirements for the scoring system are available in the preinstallation manual available from the seller or distributor as well as from Steltronic directly by sending
a request e-mail to; [email protected]
*the availability of this feature depends by Lane computer model.
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
[4.0] Monitor Dimensions
ALL DIMENSIONS ARE IN MILLIMETRES
Monitor weight: 16,5KG
Pg. 12 of 28
Rev A.
June 2007
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Pg. 13 of 28
Rev A.
June 2007
[5.0] Available monitor’s supports
The monitor’s could be installed in 4 different ways:
[A] SINGLES
Each monitor is in the center
of each bowling lane
[B] 2 NEAR MONITOR
2 monitors, one near the other
at the center of the ball return
[C] 2 MONITOR + CENTRAL PLATE
The 2 monitor are divided
by a central plate
[D] 3 NEAR MONITOR
3 monitors, one near each other
at the center of the ball return.
The third monitor (central) is used to
display Video signal
All of the hanging method use the same way for hung the structure to the ceiling using a vertical “T”
bracket which can either be attached directly to the ceiling or to another hanging support using, chains,
steel cable or floor bolts (NOT SUPPLIED BY STELTRONIC). The monitors can be inclined to a max
angle of 20 degrees.
Washer, bolt, screws and metric nut for assembly the structure will be supplied by Steltronic,
chain, fisher, etc for fix the T bracket to ceiling must be supplied by installers.
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Pg. 14 of 28
Rev A.
June 2007
[5.1] Fixing the Brackets to the ceiling
NOTE: All hanging method use the same “T” bracket
for support the monitor to the ceiling. The number of the brackets necessary depends by
the number of the monitors.
Each “T” Bracket includes 2 M8 eye bolts, these can be used with chain or steel cable; alternatively the
“T” bracket can be fixed directly to a concrete ceiling with fisher. The distance between the center of
the 2 eye bolts is 35 centimeters.
To fix the monitor frame to the “T” bracket use 2 M8x55 bolts
(bolts + washers + self locking nuts) fixed to the “L” adjustable
supports.
The “L” supports allow to vary the monitor inclination up to a
maximum of 20 degrees.
Place the plastic cup into the tube for close the holes.
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Pg. 15 of 28
Rev A.
June 2007
Installation on concrete ceiling
Installation with chain
Warning: the “T” bracket for single monitor installation must be fixed without chain for
preventing possible monitor oscillation: It’s possible add an horizontal bar between the 2
brackets using the 2 extra hole on the top of each bracket.
The monitors could be fix on the “T” bracket in 2
different high:
A = 66 centimetres
B = 46 centimetres
Minimum clearance from ground to the bottom
of the monitors: 2.5 meters / 8 feet.
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Pg. 16 of 28
Rev A.
June 2007
The distance between the 2 “T” bracket depends by choose of the installation’s method:
79,4 CM
79,4 CM
95,4 CM
79,4 CM
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Pg. 17 of 28
Rev A.
June 2007
[5.2] Assembly the Frame for single monitor [Configuration A]
Description
Monitor Frame
“L” adjustable support (LF)
Square M6 Snap-Nut
Screw M6x16
Flat washer (for M6 screw)
Grip washer (for M6 screw)
“T” bracket
M8 L=60 eyebolts
M8 self nut
M8 nut
M8 washer
M8X60 screw
Holes stopper (Ø4CM)
Q.ty
01
01
03
07
07
04
01
02
04
02
04
02
03
STEL CODE
MC0023A
MW0129A
N^ 01
KIT K0082A
MW0127C
N^ 01
KIT K0083A
A
A
A
Insert the 3 M6 Snap-nut [A]
In the holes of MC0023A Frame
Attach the “L” adjustable support MW0129A
to the frame using 3 M6x16 screws+ washers
The 4 external hole of
MC0023A frame match
with the monitor VESA
holes (200X200mm).
Fix the MC0023A Frame to the monitor using 4
M6x16 screws provided with 4 Flat washers + 4
grip washers (the grip washer must be placed
between screws head and flat washer).
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Pg. 18 of 28
Rev A.
June 2007
[5.3] Hanging 2 near monitors [Configuration B]
Description
Monitor Frame
“L” adjustable support (RT)
“V” angle support
Square M6 Snap-Nut
Screw M6x16
“T” bracket
M8 L=60 eyebolts
M8 self nut
M8 nut
M8 washer
M8X60 screw
Holes stopper (Ø4CM)
Q.ty
01
01
01
01
06
14
14
08
02
04
08
04
08
04
06
STEL CODE
MC0023A
MW0129A
MW0130A
MW0164A
N^ 02
KIT K0082A
MW0127C
N^ 02
KIT K0083A
A
B
FOR BOTH MONITORS: assembly and fix the Frame MC0023A to each monitor as explained on single
monitor installation (chapter 5.2); hang the monitors one the brackets, then remove the 4 monitors’
handle [A] [B].
Using the handle screws, fix the “V” angle support MW0164A to each
monitor. The MW0164A is provide to closing an align the 2 monitors
together.
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Pg. 19 of 28
Rev A.
June 2007
[5.4] Hanging 2 monitors with Central Plate [Configuration C]
Description
Monitor Frame
Central plate
Vertical bar
Square M6 Snap-Nut
Screw M6x16
Screw M6x30 V Head
M6 self-nut
M4x20 screw
Flat washer for M4 screw
“T” bracket
M8 L=60 eyebolts
M8 self nut
M8 nut
M8 washer
M8X60 screw
Plastic bung Diam. 4CM
Q.ty
01
01
01
01
02
06
14
14
08
08
08
04
04
02
04
08
04
08
04
06
STEL CODE
MC0153A
MW0129A
MW0130A
PA049A
MW0154A
N^ 02
KIT K0082A
N^ 01
KIT K0084A
MW0127C
N^ 02
KIT K0083A
Insert 3 M6 Snap-nut in each vertical bar [A] MW0154A and fix the “L” adjustable support MW0129A
to one vertical bar and the “L” MW0130A to the other. Use 3 M6x16 screws+ washers for each bar.
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
1
Pg. 20 of 28
Rev A.
June 2007
2
To fix each vertical bar to the frame use 4 M6x30 “V head”
screws with M6 self-nut, taking care about perpendicular of the
assembly.
Fix the vertical bar to the MC0153A structure:
The vertical bar [1] with the MW0129A support must be fixed on the left side of the frame[1] MC0153A.
The vertical bar [2] with MW0130A support must be fixed on the right side of the frame MC0153A.
Before to proceed with fixing the frame to the monitors, remove the monitor’s handles that interfere
with the frame.
A
A
The MC0153A frame has the holes that match with
standard (200X200mm).
A
A
the monitor’s
VESA
Fix the frame to each monitor using 4 M6x16 screws + 4 Flat washers + 4
grip washers (the grip washer must be placed between screws head and flat
washer).
Now hang the monitor structure on the “T” bracket
CENTRAL PLATE: remove the 4 monitor’s cover screws [A]; place the Central Plate between the 2
monitors and use number 4 M4x20 screws + washer to fix the plate to the monitors.
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Pg. 21 of 28
Rev A.
June 2007
[5.5] Hanging 3 monitors [Configuration D]
Description
Monitor Frame
“V” angle support
Vertical bar
Square M6 Snap-Nut
Screw M6x16
Screw M6x30 V Head
M6 self-nut
M6 nut
M6x60 screw
“T” bracket
M8 L=60 eyebolts
M8 self nut
M8 nut
M8 washer
M8X60 screw
Plastic bung Diam. 4CM
Q.ty
01
02
01
02
03
13
21
21
12
12
08
08
04
03
04
08
04
08
04
06
STEL CODE
MC0155A
MW0129A
MW0130A
MW0164A
MW0154A
N^ 01
KIT K0085A
MW0127C
N^ 03
KIT K0083A
Insert 3 M6 Snap-nut in each vertical bar [A] MW0154A; fix the “L” adjustable support MW0129A to
two vertical bar and the “L” MW0130A to the other. Use 3 M6x16 screws+ washers for each bar.
Insert 2 M6 Snap-nut in each “V”
support MW0164A.
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Pg. 22 of 28
Rev A.
June 2007
Fix the vertical bar to the MC0153A structure:
One vertical bar with the MW0129A support must be fixed on the left side of the frame MC0155A,the
other on the center of the frame; the vertical bar [2] with MW0130A support must be fixed on the right
side of the frame.
To fix each vertical bars to the frame use 4 M6x30 “V head”
screws with M6 self-nut, taking care about perpendicular of the
assembly.
Before to fix the frame to the monitors, remove all the monitor’s handles.
The MC0155A frame has the holes that match with VESA standard
(200X200mm).
Fix the frame to each monitor using 4 M6x16 screws provided with 4 Flat
washers + 4 grip washers(the grip washer must be placed between screws
head and flat washer).
Now hang the monitor structure on the “T” brackets
To align the monitor, use the “V” MW0164A supports:
Fix one V support between the central and odd monitor using the handle’s
screws (the V must ber placed in the old handle position).
To improve more stability, use 2 M6x60 screws
the screws lock also the V support to the frame.
1
1
[1] for each V support:
For each M6x60 screw use 2 M6 nuts for registry and fix it permanently.
Screws must be turn until reach and lock the 2 snap-nut inserted on the V
support.
Repeat the operations with the central and even monitor.
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Pg. 23 of 28
Rev A.
June 2007
[6.0] Connecting the Lane computer (SUPERELEX) to the monitor
The RGB input for the monitor is the DB15 connector (VGA).
When the Superelex is installed near the monitors, use one Steltronic RGB cable CA0260C for each
lane. The Superelex could supply the AC power for to the monitor using one VDE female <>male cable
for each monitor: with this connection, it’s be possible switch ON/OFF the monitors from Wins Software.
If the Superelex is installed far from the monitor, near the pinsetter area, it’s necessary use the CAT5
TX\RX system to drive the RGB signal from Lane computer to the Monitor: the CAT5 RX box it will
connected with monitor VGA input using a standard Male<>Male VGA cable, the AC power for the
monitor must be connect directly to an Ac outlet. Refer to “RGB CAT5 installation manual” for further
details.
ODD
AUDIO
OUT
CVBS IN/ OUT
12VDC OUT
COM2
(Touch
screen
or
Wireless
RX box)
EVEN
AUDIO
OUT
EVEN
OVERHEAD
MONITOR
LAN
KEYBOARD
(MAINT. ONLY)
VGA OUT
(MAINT. ONLY)
COM1
(CA0305A adapter cable)
AC OUT(110-240VAC)
ODD OVERHEAD
MONITOR
AC OUT (110-240 VAC)
EVEN OVERHEAD
MONITOR
AC IN
(110-240VAC)
ODD
OVERHEAD
MONITOR
ODD
BOWLER’S
CONSOLE
MONITOR
Stand alone Superelex II connectors view
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Pg. 24 of 28
Rev A.
June 2007
CA0260C (Superelex <> Monitor – VGA input)
[6.1] Wins software settings for 16:9 monitors
The LCD 32” monitor is widescreen 16/9, to adapt the WINS SCORE picture to fit correctly in the
monitor is necessary change a parameter in the LANES_MP.RSR file on the Wins Main Desk (server):
1)
2)
3)
4)
5)
[MAIN DESK] Browse the C drive.
Open the TCPSERV folder and the DATI_COM sub-folder.
Identify the LANES_MP.RSR file and open it using the NOTEPAD program.
Look for the VIDOFFSX = 112 line. The line must be set as VIDOFFSX = 98
Save and exit, than reboot the lane computer.
WARNING: If the line begin with ;VIDOFFSX = 98 delete the semi colon at the start of the line.
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Pg. 25 of 28
Rev A.
June 2007
[6.2] Connecting the Lane computer (V.L.C.) to the monitor
The RGB input for the monitor is the DB15 connector (VGA).NOTE: the DVI-D connector is not used.
When the V.L.C. lane computer is installed near the monitors, use one high quality DB15 VGA
male<>male cable to connect V.L.C. output to VGA input of the monitor. the AC power for the monitor
must be connect directly to an Ac outlet.
If the V.L.C. is installed far from the monitor, near the pinsetter area, it’s necessary use the CAT5
TX\RX system to drive the RGB signal from Lane computer to the Monitor: the CAT5 RX box it will
connected with monitor VGA input using an DB15 Male<>Male VGA cable. Refer to “RGB CAT5
installation manual” for further details.
2
2
1
1
3
3
5
4
5
6
7
6
8
9
9
10
10
11
V.L.C. mod. A
4
7
8
11
V.L.C. mod. B
Note: the only difference between V.L.C. model A and Model B is the position of the COM1 port.
[1] AC input Selector (110/230VAC)
[2] AC power ON/OFF switch
[3] AC input (VDE)
[4] Power Led
[5] ON/OFF button
[6] AUX 12/5 VDC out
[7] +12VDC out
[8] COM1 (reserved for A.P.I. connection)
[9] LAN input
[10] ODD VGA output
[11] 12 EVEN VGA Output (with DVI/VGA adapter) – do not use a DVI/DVI cable -
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Pg. 26 of 28
Rev A.
June 2007
[7.0] Display Video signal (Superelex lane computer)
The LCD monitors can be used to watch a Video signal instead of Score. When the monitors is
connected to the Superelex, the switch command between Video/SCORE could be send from Wins Front
Desk; it’s also possible set from Wins software a permanent command to switch TV automatically when
nobody play.
With Superelex, the only Source connection used in the monitor is the RGB (VGA input); the CVBS
daisy chain is connected directly on Superelex that provide the conversion from CVBS to RGB.
WARNING!
Connect MAX 8 Superelex in one daisy chain. For center with more than 8 Superelex, connect the CVBS
source signal to a CVBS amplifier (supplied by Steltronic if requested) and split the Superelex in 2 or
more daisy chain using the video amplifier output.
The free output of the last Superelex in each chain must be close with a 75 OHM short-cup.
It’s also possible connect the Video signal to the local monitor S-VIDEO/VIDEO input connectors and
use the remote control for switch Score/Video; using the local S-Video/Video monitor input it’s possible
use the Picture In Picture monitor function and split the screen with Score/TV.
WARNING:
The AUDIO signal is NOT managed by the lane computers; connect the audio output on the
DVD, VCR or Decoder to the center sound system.
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Pg. 27 of 28
Rev A.
June 2007
[7.1] Display Video signal (V.L.C. lane computer)
The LCD monitors can be used to watch a Video signal instead of Score. When the monitors is
connected to the V.L.C. is necessary use the Remote Control for switch between Score (VGA) and video
signal (COMPOSITIVE / S-VIDEO – COMPONENT).
Connecting a signal to the local S-Video / Video monitor input it’s possible use the Picture In Picture
monitor function and split the screen with Score/TV.
Using an CVBS video amplifier (supplied by Steltronic if requested) it’s possible connect 6 monitors
under one CVBS source (DVD/SAT, etc); To connect more monitors, use more CVBS video amplifier in
chain.
IN
CVBS VIDEO
AMPLIFIER
OUT
IN
CVBS VIDEO
AMPLIFIER
OUT
CVBS SOURCE (DVD/SAT/VCR)
CVBS connection using the COMPOSITIVE Monitor input
WARNING:
The AUDIO signal is NOT managed by the lane computers; connect the audio output on the
DVD, VCR or Decoder to the center sound system.
STELTRONIC S.p.A.
Tel +39 030 2190811 - Fax +39 030
Steltronic
ST-HB32 LCD 32”
16/9 Monitor
Steltronic_ST-HB32LCD_ 32_16-9_Monitor_User_and_Installation_Manual (pdf)
REV. A
June 2007
Steltronic S.p.A.
Via Artigianale 34, 25082 Botticino Sera Brescia - Italy
Tel: (+39) 030 2190811
Fax: (+39) 030 2190798
Info : [email protected]
Web: www.Steltronic.com
Customer Service: (+ 39) 030 2190830
Email: [email protected]
Pg. 28 of 28
Rev A.
June 2007

Steltronic ST-HB32 LCD 32” 16/9 Monitor User and Installation Manual

Transcription

Similar documents

Atlantis Energy Systems Inc.

Regions CD Check Viewer Installation Guide

Chemcrest Installation Guide

Sigma bite brochure

G:\release manual\vga\R925128VH

Zonnestraal - English

KV “ANDENES” - KV “SENJA” - KV “NORDKAPP”

QuadraTec™ - Auralex Acoustics

Products_files/6 (catalogo DECO PROJECTS.EN)

S kyline - Franz Viegener