BMP Billet Head Kits

Transcription

BMP Billet Head Kits
1
ski-doo billet head kits
40
41
The Bikeman Performance Billet Head Kits give you the best of both worlds with excellent horsepower gains and better
cooling capacity. Our billet head kits utilize an improved squish band, new pocket design, and slightly more compression
for pump gas friendly horsepower. High elevation heads can gain up to 20lbs of compression and gain up to 10hp! Low
altitude heads gain up to 7 horesepower with our dome design. The huge factor why our heads work so well is the cooling
capacity. We nearly double the stock head capacity which helps your machine run a more consistent, lower temperature.
This is a big deal because many models pull timing as you get hot and you start dropping horsepower fast. Help keep that
horsepower on tap by adding one of these trick looking heads!
- Increases Cooling Capacity
- Better Heat Dissipation
- Lower Running Temps
- Increase Horsepower
- Increase Torque
BMP Billet
Head Kits
- Great Looks!
Part #
Model
Year
+ HP
Altitude
$ Price
04-211-L
Rev/Summit 800
2003-07
5-7
Low
479.95
04-211H
Rev/Summit 800
2003-07
8-10
High
479.95
04-212L
Rev/Summit XP 800R
08-11
5-6
Low
479.95
04-212H
Rev/Summit XP 800R
08-11
8-10
High
479.95
04-212T
Rev/Summit XP 800R (Turbo Dome)
08-11
Varies
TURBO
479.95
04-213L
Rev/Summit 600
03-08
4-5
Low
479.95
04-213H
Rev/Summit 600
03-08
6-7
High
479.95
04-214L
TNT/500SS/MXZSport
All
4-5
Low
479.95
04-214H
TNT/500SS/MXZSport
All
6-7
High
479.95
04-SDRS
600 Race Sled (Domes only)
All
4-5
Race
215 per set
04-MZDL
Mach Z 1000 (Domes Only)
All
3-4
Low
215 per set
04-MZDH
Mach Z 1000 (Domes Only)
All
7-8
High
215 per set
04-215L
E-Tec 800
All
3-4
Low
CALL
04-215H
E-Tec 800
All
5-6
High
CALL
42
ski-doo performance manifolds
Our high flow manifolds for Ski-Doo models are simply unmatched! Countless hours of dyno testing led us to the best possible manifold for your Rev, XP, or E-Tec. Easy bolt-on performance you can feel. Not only are these manifolds good gains
in horsepower throughout the RPM range, they are a big torque adder also! On models besides the 800R XP & E-Tec the
manifolds are an excellent addition to our single pipe and muffler. Horsepower on the E-Tec 800 & XP 800R are simply
amazing. No ones y-pipe, or y-pipe + pipe combo we have tested makes the power just our y-pipe. Manifolds are made
from high quality steel and are extremely durable. Available in black or ceramic chrome.
ski-doo pipes
43
For the Rev models we offer our Stealth pipe. This means you can run it bare or you can re-install your stock heat shield for
that sleeper look. Both the 600 and 800 rev pipes make huge power gains over stock and they don’t do it with a necked
down outlet like other brands. Because of this, these pipes produce more low end, mid range and peak horsepower. They
are great for both low altitude and high altitude riding. The Stealth pipes fit right into the stock muffler or you can use one
of our BMP lightweight mufflers. This pipe will work well with the stock exhaust manifold, or it can be used with our BMP
high performance manifold. The ported 800 pipe is designed to run at higher rpm in combination with ported cylinder
with a higher exhaust ports. Our ported Rev 800 jumped from 166 to 172 horsepower with the ported pipe compared to
the standard Stealth pipe! The ported pipe also works very good with our big bore kits. No fuel changes needed on the
stealth pipe for the standard Rev 600 & 800 models, simply bolt-on and go! Ported pipes will require re-jetting.
The BMP E-Tec 800 pipe is a grunt pipe which was developed for the mountain riders 4000ft and above. It can be used
with a factory y-pipe, however our BMP high flow y-pipe is recommended. This large volume pipe produces tons of low
end and mid range power with killer throttle response and 5-7 peak horsepower. It fits the stock muffler or one of our
lightweight mufflers. When used in combination with our Y pipe and muffler, it works unreal in deep snow and mountain
riding. Ceramic coated silver for durability, keeping the heat in the pipe, and to look darn nice! No fuel controller is required, just load the clutch hard and let the motor work with this pipe. Pipes come with a bung for the stock EGT probe.
Unmatched
Performance
Part #
E-Tec 800
+6HP
Model
Year
+ HP
Peak RPM
Finish
Price
01-210
Rev 600
2003-07
8-9
8000-8200
Black
$455.95
01-210-C
Rev 600
2003-07
8-9
8000-8200
Ceramic
$539.95
01-211
Rev 800 HO/STD/POWERTEK
2003-07
9-11
7900-8100
Black
$455.95
01-211-C
Rev 800 HO/STD/POWERTEK
2003-07
9-11
7900-8100
Ceramic
$539.95
01-211P
Rev 800 HO/STD/PTEK PORTED MOTOR
2003-07
13-15
8300-8400
Black
$455.95
01-211P-C
Rev 800 HO/STD/PTEK PORTED MOTOR
2003-07
13-15
8300-8400
Ceramic
$539.95
Summit 800R
2007
6-7
8300-8400
Black
$455.95
Part #
Model
Year
+ HP
Finish
Price
01-212
03-208
Rev/Summit XP 800R
2008-09
4-5
Black
$229.95
01-212-C
Summit 800R
2007
6-7
8300-8400
Ceramic
$539.95
01-213-C
E-Tec 800 Summit HIGH ALT ONLY
2011-Up
5-7
7900-8000
Ceramic
$539.95
03-208-C
Rev/Summit XP 800R
2008-09
4-5
Ceramic
$254.95
03-209
Rev/Summit XP 800R
2010-11
4-5
Black
$229.95
03-209-C
Rev/Summit XP 800R
2010-11
4-5
Ceramic
$254.95
03-210
Rev/Summit 800
2003-07
3-4
Black
$229.95
03-210-C
Rev/Summit 800
2003-07
3-4
Ceramic
$254.95
03-211
Rev/Summit E-Tec 800
2011-14
5-6
Black
$229.95
03-211-C
Rev/Summit E-Tec 800
2011-14
5-6
Ceramic
$254.95
03-212
Rev/Summit STD/XP/E-Tec 600
2004-14
2-3
Black
$229.95
03-212-C
Rev/Summit STD/XP/E-Tec 600
2004-14
2-3
Ceramic
$254.95
E-Tec 800 high altitude pipe
E-TEC 800 Pipe
Adds 5hp and
great low end
torque!
Ski-Doo Stock Pipe Mods
This is one of the best exhaust deals on the market. Our pipe mods are
proven and get rave reviews from customers! Gains are huge for the price
tag! The great part is no one would ever know you have this modification
done. The stock heat shield can still be used, all stock mounting, and fits
right into your stock or BMP muffler. Simply remove your heat shield and
box the pipe up carefully with your name and phone number inside the
box. Be sure to list any other performance modifications done to your sled.
Once we recieve the pipe, we will call you for payment and return shipping
information. Fuel changes are not usually required. We recommend using
one of our stage 2 clutch kits with this mod.
Part #
Model
+ HP
Peak RPM
Price
01-501
MXZ 600
5-6
8000-8100
$275
01-502
MXZ 800
7-8
7900-8000
$275
01-503
XP 600 SDI
6-7
8100
$275
01-504
Mach Z 1000
5-6
7800-8000
$275
01-505
Rev 600
6-7
8000-8100
$275
01-506
Rev 800
6-7
7900-8000
$275
01-507
Rev 500SS
5-6
8000-8100
$275
01-508
XP 500SS/TNT/Sport
5-6
8000-8100
$275
01-509
MXZ 700
7-8
8000-8100
$275
01-510
E-Tec 600
5-6
8000-8100
$275
Velocity!
Dyno and Field Tested
Will not lose horsepower
Some Gain Horsepower
Gained Throttle Response
Quality Fit And Finish
Black or Ceramic
GREAT SOUND WITHOUT BEING TOO LOUD
Part #
Model
Year
Lbs Lost
Finish
Price
02-218
Mach Z/ Summit 1000 (+5hp!!!)
All
-15
Black
$299.95
45
XP 600/800
ceramic
Powder
Lite
XP 600
/800
black
Our Powderlite Mufflers have taken the industry by storm! They are extremely light, fit great, and sound great! Plus you
can’t beat the price! They are designed to be a louder muffler with a straight through mechanical baffle design (no packing). All of our mufflers are developed on our Superflow dyno to assure they make the same or more horsepower than
stock. Most Powder Lite Mufflers only weigh 5-6lbs! HUGE WEIGHT SAVINGS! No other changes neccesary, fit with little to
no modification. Available in high temp black paint or ceramic coated to a chrome looking finish. E-Tec 800 models may require a sensor adapter to run right. This is not normally the case, but in some rare cases you will need one to achieve peak
RPM under warmer engine temps. This can be found on page 52.
Get
Full
E-T
ec
6
bl 00/
ac 80
k
0
E-T
ec
Ce 600
ra /8
m 00
ic
Our lightweight Full Velocity Mufflers are all developed on our Superflow dynomometer to assure they produce the same or
more horsepower as stock. Mach Z/Summit 1000 models produce 3-5hp more than stock! Most other Ski-Doo models see
a 1-2hp gain. Some of these mufflers are up to 16lbs lighter than the factory muffler. These mufflers are designed to be
louder than stock, but not obnoxious. They have a deep throaty sound that you will love! Will not wear out, all mechanical
baffles with no packing (excludes turbo mufflers). Installation is a breeze all of our mufflers are a direct factory replacement with little to no modification required. Available in high temp black paint or ceramic coated to a chrome looking finish.
E-Tec 800 models may require a sensor adapter to run right. This is not normally the case, but in some rare cases you will
need one to achieve peak RPM under warmer engine temps. This can be found on page 52.
ski-doo powder lite mufflers
E-Tec 600/800
black
44
ski-doo full velocity mufflers
Light
Weight
with no
loss in
power!
02-218-C
Mach Z/Summit 1000 (+5hp!!!)
All
-15
Ceramic
$349.95
Part #
Model
Year
Lbs Lost
Finish
Price
02-219
Rev/Summit 600/800
2003-07
-9
Black
$299.95
02-218PL
Mach Z/Summit 1000 (+5hp!!!)
All
-16
Black
$289.95
02-219-C
Rev/Summit 600/800
2003-07
-9
Ceramic
$349.95
02-218PL-C
Mach Z/Summit 1000 (+5hp!!!)
All
-16
Ceramic
$329.95
02-220
Rev/Summit 600 SDI
2003-07
-9
Black
$299.95
02-219PL
Rev/Summit 600/800
2003-07
-10
Black
$289.95
02-220-C
Rev/Summit 600 SDI
2003-07
-9
Ceramic
$349.95
02-219PL-C
Rev/Summit 600/800
2003-07
-10
Ceramic
$329.95
02-221
Rev/Summit XP 800R, XP TNT, RS600, MXZSPORT
2008-14
-9
Black
$299.95
02-220PL
Rev 600 SDI
2003-07
-10
Black
$289.95
02-221-C
Rev/Summit XP 800R, XP TNT, RS600, MXZSPORT
2008-14
-9
Ceramic
$349.95
02-220PL-C
Rev 600 SDI
2003-07
-10
Ceramic
$329.95
02-222
E-Tec 600/800, XP 600 SDI (+2hp)
2008-14
-9
Black
$299.95
02-221PL
Rev/Summit XP 800R, XP TNT, RS600, MXZSPORT
2008-11
-10
Black
$289.95
02-222-C
E-Tec 600/800, XP 600 SDI (+2hp)
2008-14
-9
Ceramic
$349.95
02-221PL-C
Rev/Summit XP 800R, XP TNT, RS600, MXZSPORT
2008-11
-10
Ceramic
$329.95
02-224
MXZX 700/800
2001-02
-8
Black
$299.95
02-222PL
E-Tec 600/800, XP 600 SDI (+2hp)
2011-14
-10
Black
$289.95
02-224
MXZX 700/800
2001-02
-8
Ceramic
$349.95
02-222PL-C
E-Tec 600/800, XP 600 SDI (+2hp)
2011-14
-10
Ceramic
$329.95
02-225
4-Tec 1200 Quiet Muffler (+5-7hp)
2009-Up
-8
Ceramic
$479.95
02-225PL-C
4 Tec 1200 (+5-7hp)
10-14
-14
Ceramic
$359.95
ski-doo clutch kits
46
ski-doo clutch kits
47
Team Tied XP/XM/XS Clutch Kits
Rev/Summit XM/XS/XP Stage 2 Clutch Kits
Bikeman performance clutch kits are designed to optimize performance for your machine. The high altitude machines are
designed to have very quick throttle response in deep snow and boondocking, yet also have a strong pull up the mountain. These kits are developed and extensively tested in the Rocky Mountains of the USA and Canada. The flat land kits
are developed to provide strong acceleration, quick throttle response, and great top speed. One key benefit to the BMP
stage two kit is the smooth shift bearing for the driven clutch. No other company has this unique feature. The smooth shift
bearing replaces the stock slider bushings under the spring. The smooth shift bearing will eliminate any friction produced
from the stock bushing that must twist and push against the helix when the clutch is opening. Our custom helix was designed
to accept this special bearing along with a stiffer driven clutch spring. The combination produces wicked throttle response
and also more aggressive acceleration. The primary clutch gets heavier pins in all models, except the E-Tec low altitude kit,
which used larger diameter rollers. The primary spring is also changed to improve throttle response and acceleration. This
is the first performance mod you should do to your E-Tec. Outstanding performance for your money!
Please specify Altitude and any modifications done to your sled when ordering.
Year
Model
Altitude
Parts Included
Price
06-TNT
All
XP TNT / MXZ SPORT
Low
Adjustable Pin Kit, Primary Spring, Secondary Spring, Custom Cut Helix, Smooth Shift Bearing
$359.95
06-600SDI
All
XP 600 SDI
Low
Adjustable Pin Kit, Primary Spring, Secondary Spring, Custom Cut Helix, Smooth Shift Beari
$359.95
06-600ETEC
All
XP 600 E-TEC
Low
Adjustable Pin Kit, Primary Spring, Secondary Spring, Custom Cut Helix, Smooth Shift Bearing
$359.95
06-800R
All
XP 800R
Low
Adjustable Pin Kit, Primary Spring, Secondary Spring, Custom Cut Helix, Smooth Shift Bearing
$359.95
06-800R-SUMMIT
All
XP 800R Summit
High
Adjustable Pin Kit, Primary Spring, Secondary Spring, Custom Cut Helix, Smooth Shift Bearing
$359.95
06-800R-RENEGADE
All
XP 800R Renegade
Low
Adjustable Pin Kit, Primary Spring, Secondary Spring, Custom Cut Helix, Smooth Shift Bearing, Set of Ramps
$419.95
06-800ETEC
All
XP 800 E-TEC
Low
Primary Spring, Secondary Spring, Custom Cut Helix,
Smooth Shift Bearing, Oversize Rollers
$359.95
06-800ETEC-SUMMIT
All
Cory Micku XP 800 ETEC Summit
High
Adjustable Pin Kit, Primary Spring, Secondary Spring, Custom Cut Helix, Smooth Shift Bearing, Set of Ramps
$359.95
06-800ETEC-RENEGADE
All
XP 800 E-TEC Renegade
Low
Primary Spring, Secondary Spring, Custom Cut Helix,
Smooth Shift Bearing, Oversize Rollers
$359.95
06-4TEC
2008-12
4-TEC 1200
Low
Adjustable Pin Kit, Primary Spring, Custom Cut Helix
$289.95
06-4TEC-B
2013-14
4-TEC 1200
Low
3 Arm Adjustable Goldstar Weights, Primary Spring, Secondary Spring, Custom Cut Helix, Smooth Shift Bearing
$479.95
06-4TEC-C
2013-14
4-TEC 1200
Big Horsepower KIt
Low
6 Arm Adjustable Goldstar Weights, Primary Spring, Secondary Spring, Custom Cut Helix, Smooth Shift Bearing
$719.95
CLUTCH PULLERS ON PAGE 109
Part Number
Take your XP to the next level with the TEAM Tied Conversion Kit. Upgrade your sled to the performance
that non-tied clutches cannot deliver. The Tied clutch backshifts far superior to standard clutches letting us
use a softer spring. This means you get the best possible upshift while still getting lightning fast backshifts!
Great thing is it allows you to align your clutches unlike the factory setup. Comes with all the parts you
need to install the patented TEAM Tied clutch ,and the tuning components to make it rip! Kits Include: Team
jackshaft to mount the Team clutch, Team TIED Driven Clutch, Team Helix, TRA Ramps, Adjustable Pin Kit,
Drive & Driven Springs. Kits marked with an * come with chain and sprocket
Part Number
Model
Year
Elevation
Price
TP-520158-TH *
Summit XP 800 154"
2008-2011
9000-12000 ft
$899.95
TP-520160-TH *
Summit XP 800 154"
2008-2011
6000-9000 ft
$899.95
TP-520161-TH
MXZ XP 800
2008-2011
0-3000 ft
$839.95
TP-520162-TH
Renegade XP 800
2008-2011
0-3000 ft
$899.95
TP-520163-TH *
Summit XP 800
2008-2011
0-3000 ft
$899.95
TP-520165-TH
Summit XP 800 163"
2008-2011
6000-9000 ft
$839.95
TP-520166-TH
Summit XP 800 163"
2008-2011
9000-12000 ft
$869.95
TP-520168-TH
MXZ XP 600 SDI
2008-UP
0-3000 ft
$779.95
TP-520170-TH
Summit XP 600
2008-UP
6000-9000 ft
$899.95
TP-520176-TH
Renegade 4-TEC
2008-UP
0-3000 ft
$779.95
TP520177-TH
MXZ XP 600 TNT
2008-UP
0-3000 ft
$779.95
TP-520179-TH
Summit 800 E-TEC 154"
2011-2013
6000-9000 ft
$779.95
TP-520193-TH
Renegade E-TEC 800
2011-2013
0-3000 ft
$839.95
TP-520194-TH
MXZ 800 800 E-TEC
2011-2013
0-3000 ft
$839.95
Mach Z / Renegade 1000 Stage 1 Clutch Kit : $339.95
This is the ultimate primary clutching setup for the Mach Z 1000. Wicked accelleration and pull
will put a huge smile on your face. Our testing showed an easy 8-10 sled length lead over the
stock clutching. The backshift is noticeably increased as well. This kit pulls hard!! Comes with
a full set of adjustable pins, rollers, weights, and a new primary spring. Simply bolt it in and
hang on. Combine this with our Team secondary clutch for the complete setup
BMP Rev/Summit Clutch Kits
Wake up your Rev with these powerful clutch kits! Harder punch out of the hole, faster acceleration and more throttle response is what you will feel with this clutch kit. You will gain
4-5 sled length over stock and have much more out of the corner power. Kit includes primary and secondary springs, helix, ramps(depends on kit), and adjustable pin kit. A must have
for fast trail riding, mountain riding or ditch banging! Due to the large variation in which
models have the roller clutch, please inspect your secondary clutch to see if you have the
button or roller clutch before ordering. FYI: X package models came with a roller secondary. Please specify altitude and any other modifications you have done to the sled.
Part Number
Model
Price
06-REVR
Rev/Summit 600 Roller
$359.95
06-REV
Rev/Summit 600 Button
$359.95
06-REV8R
Rev/Summit 800 Roller
$359.95
06-REV8
Rev/Summit 800 Button
$359.95
06-REV8REV
2007 Summit 800R
$359.95
48
ski-doo bolt-on performer kits
Stage 1
Our bolt-on performance packages get rave reviews from dealers and customers worldwide. We combine the best parts
we offer into one easy, bolt-on kit. Adding one or two performance parts will work, but we all know on sleds its about
the right combination of go fast parts and clutching to make a truley fast machine. This is where our R&D work comes into
play, and really benefits you. Plain and simple, these kits flat out rock! Please specify riding altitude and any other sled
modifications when ordering. Upgrade to a ceramic y-pipe for $30 extra. Ceramic single pipe upgrade is $70 extra.
Part Number
Model
Year
Parts Included
HP
Price
13-REV500SS-1
REV 500 SS
All
Billet Head, Boyesen Reed Petals, Clutch Kit, Pipe Mod & 2" Flow
Rites.
+12-14
$1,260
13-MZ1000-1
MACH Z 1000
ALL
Billet Domes, Boyesen Rage Cages, Clutch Kit, Pipe Mod & 2" Flow
Rites
+13-15
$1,260
13-XPTNT500-1
XP TNT 500
XP 600 Carb
2008-14
Billet Head, Boyesen Reed Petals, Clutch Kit, Pipe Mod & 2" Flow
Rites.
+12-14
$1260
13-600SDI-1
XP 600 SDI
2008
Billet Head, Reed Valve System, Clutch Kit, Stealth Pipe & 2" Flow
Rites
+15-16
$1,795
13-REV800-1
REV 800
2003-07
Billet Head, Reed Valve System, Clutch Kit, Stealth Pipe & 2" Flow
Rites
+18-20
$1,745
13-XP800R-1
XP 800R
2008-11
Billet Head, Reed Valve System, Clutch Kit, Y-Pipe, Needle Shims & 2"
Flow Rites
+14-15
$1,435
13-ETEC800PL-1
XP E-TEC 800
2011-14
Stage 2 Clutch Kit, Boyesen Rage Cages, Y-Pipe, Powder Lite Muffler
& Sensor Adapter
+9-10
$1,315
13-ETEC800FV-1
XP E-TEC 800
2011-14
Stage 2 Clutch Kit, Boyesen Rage Cages, Y-Pipe, Full Velocity Muffler
& Sensor Adapter
+9-10
$1,315
13-4TEC-1
4 Tec 1200
2008-12
BMP Muffler, BMP Header, Power Commander, Stage 2 Clutch Kit
+19-20
$1,860
13-4TEC-B-1
4 Tec 1200
2013-14
BMP Muffler, BMP Header, Power Commander, Stage 2 Clutch Kit
+19-20
$2,035
E-TEC 800
XP 800
4 TEC 1200
ski-doo bolt-on performer kits
49
Stage 3
On Ski-Doo models we skip stage 2 and go straight for stage 3 since most stage 1 kits include a billet head. The stage
3 includes everything in your stage 1 kit plus professional cylinder porting. E-Tec 800 models see porting and a Power
Commander 5 come into the stage 3. This power commander 5 will be pre-programmed with our custom map. Huge gains
with our reliable trail cylinder porting! The factory leaves a lot on the table, and we are here to deliver that power to you!
Don’t be fooled by others, our porting is the best in the biz! Be sure to send exhaust valves(blades only) and cylinders.
Part Number
Model
Year
Parts Included
HP
Price
13-REV500SS-3
REV 500 SS
All
Cylinder Porting, Billet Head, Boyesen Reed Petals, Clutch Kit,
Pipe Mod, & 2" Flow Rites.
+18-19
$1,920
13-XPTNT500-3
XP TNT 500
XP 600 Carb
2008-13
Cylinder Porting, Billet Head, Boyesen Reed Petals, Clutch Kit,
Pipe Mod, & 2" Flow Rites.
+18-19
$1,920
13-600SDI-3
XP 600 SDI
2008-11
Cylinder Porting, Billet Head, Reed Valve System, Clutch Kit,
Stealth Pipe, & 2" Flow Rites
+19-21
$2,455
13-REV800-3
REV 800
2003-07
Cylinder Porting, Billet Head, Reed Valve System, Clutch Kit,
Stealth Pipe, & 2" Flow Rites
+22-24
$2,395
13-XP800R-3
XP 800R
2008-11
Cylinder Porting, Billet Head, Reed Valve System, Clutch Kit, YPipe, Needle Shims, Porting & 2" Flow Rites
+19-20
$2,095
13-ETEC800PL-3
XP/XM/XS E-TEC 800
2011-14
Cylinder Porting, Power Commander 5, Stage 2 Clutch Kit, Boyesen Rage Cages, Y-Pipe, Powder Lite Muffler & Sensor Adapter
+17-18
$2,515
13-ETEC800FV-3
XP/XM/XS E-TEC 800
2011-14
Cylinder Porting, Power Commander 5, Stage 2 Clutch Kit, Boyesen Rage Cages, Y-Pipe, Full Velocity Muffler & Sensor Adapter
+17-18
$2,515
13-MZ1000-3
MACH Z 1000
ALL
Cylinder Porting, Billet Domes, Boyesen Rage Cages, Clutch Kit,
Pipe Mod, Fuel Controller & 2" Flow Rites
+18-20
$2,395
***MUST SEND EXHAUST VALVES WITH CYLINDERS***
ski-doo big bore kits
50
ski-doo big bore kits
E-Tec 800 to 860 Big Bore
Get ready to blow your competition away! We have abused our 860cc E-Tec motor package for a couple seasons now and
it has proven to be a winner! This kit has all sorts of grunt and torque that just keeps on pulling!! In the steep and deep of
the rockies, to the flat lakes of Michigan, this is the motor that just keeps ripping. We all know the E-Tec is a heck of a motor, but with our porting and custom Wossner pistons the E-Tec becomes a real monster! It produces 185 horsepower and
over 120 lb/ft of torque with our stage 2 porting on pump gas. The cool part is we can reprogram your stock ECU with our
big bore mapping, or you can choose to install a power commander EFI controller. Simply send us you stock cylinder, head
and exhaust valves(Blades only please). We will then bore your cylinders, port them, modify your stock head, and machine
your exhaust valves. For the best results go with our complete big bore kit which includes everything you need for the big
bore motor package.
09-SD880BB : Rev XP 880 Big Bore Kit
This kit is one of our most popular big bore kits. Why? Because it works and it smokes the competions big bores! With our
big bore Y pipe and stock pipe this kit makes just over 180hp. Part of why it works so well is because we developed the
motors torque to be a real driving force behind the performance. Thats 20 more lb/ft of torque over the stock motor! You
can really feel it too! We have been abusing the competition all over North America with this kit. On the ice in New York, to
the hills of Wisconsin, to the Mountains of British Columbia, we just keep turning heads. Send us your cylinder and exhaust
valves so that we can bore them out. Extensive porting and fresh nikasil is next. Our 86mm forged dual ring pistons have
proven to be very durable for many hard miles. Add our billet head for extra cooling and powerful combustion chambers.
We also put the o rings into the dome and machined the cylinder to accept the new style dome. This gives the inner o-ring
better protection if you were to run extra timing or nitrous. For best results use with Boyesen Rage Cages, 880 Big Bore
clutch kit and our performance Y-Pipe. Available for both low and high altitudes, please specify when ordering. We offer a
Stage 2 which has even more drastic porting and a gets you 5-7 extra ponies.
GO BIG BORE
860 E-TEC
Torque Monster!
185 Horsepower
122 Torque
Part Number
Description
Parts Included
Price
09-SD-860BB
Stage 1 860 Big Bore
Exchange Cyilnders, Exchange Exhaust Valves, Exchange Head, Pistons, Circlips, Rings,
Wristpins.
$2395
09-SD-860BB-COM
Stage 1 860 Big Bore
COMPLETE
Exchange Cyilnders, Exchange Exhaust Valves, Exchange Head, Pistons, Circlips, Rings,
Wristpins, Power Commander 5(or ECU reprogram), BMP Black Y-Pipe, Boyesen Rage
Cages, 860 Big Bore Stage 2 Clutch Kit, Top End Gasket Kit
$3550
Add Prefix -S2
Stage 2 860 Upgrade
More drastic porting for those serious about getting every horsepower. 4-5hp over Stage 1
$240
51
AS SEEN IN SLEDNECKS
Option
$ Price
Main Jet Pair
$6.95
Pilot Jets Pair
$6.95
.020" Needle Shim Pair
$5.95
2" Flow Rites
$24.95ea
Full Velocity Muffler
$299.95
Powder Lite Muffler
$269.95
Big Bore Clutch Kit
$439.95
Black Y-Pipe
$229.95
Ceramic Y-Pipe
$299.95
Boyesen Rage Cages
$349.95
Top End Gasket Kit
$89.95
Part Number
Description
Parts Included
Price
09-SD-880BB
Stage 1 880 Big Bore
Exchange Big Bore Cylinders, Exchange Exhaust Valves, 2 Pistons with rings, circlips &
wristpins, 880 Billet Head Kit
$2635
09-SD-880BB-COM
Stage 1 880 Big Bore
COMPLETE
Exchange Big Bore Cylinders, Exchange Exhaust Valves, 2 Pistons with rings, circlips &
wristpins, 880 Billet Head Kit, Black Y-Pipe, Boyesen Rage Cages, Needle Shims, Pilot
Jets, Main Jets, Top End Gasket Kit
$3715
Add Prefix
Stage 2 880 Upgrade
More drastic porting for those serious about getting every horsepower. 4-5hp over Stage 1
$240
-S2
09-SD1100BB : Mach Z/ Summit 1000 1100 Big Bore - $2395.00
Here it is! You’ve asked for more power and we delivered. This kit makes 215 horsepower with the quiet twin pipes and has
a ton to torque. It’s just a fun ride with such unreal throttle response and gut wrenching pull on the lake, up the mountain,
or down the trail. We offer a high altitude version to keep the Summits ripping up the mountain. And we have spent alot
of time pushing the nitrous button and this motor loves it!! Just send us your cylinder and we will bore it, extensively port it
for maximum trail/mountain, or lake race power, and re-nikasil plate the bore. You will then get a pair of our gas ported
forged pistons and a set of our billet domes. Finish off with a set of quiet canister or indivual silenced BMP modified Crank
Shop twin pipes. A Boondocker EFI control box will be required for proper fuel delivery. We also have a strong clutch kit
for this sled, and nitrous kits. The cool part is besides the pipes, from the outside, you can’t tell it’s a 1100. A real sleeper!!
Gains 20 horsepower in the mid range over a ported 1000 with twin pipes.
***MUST SEND EXHAUST VALVES WITH CYLINDERS***
52
ski-doo misc parts
05-TRAQC : BMP TRA Quick Clickers - $59.95
This awesome kit allows you to adjust your clicker position without getting out all the
tools! Quit dropping the nuts in the snow and fumbling around adjusting your clicker in
the cold. Once installed this kit allows you to simply push in and turn the adjuster bolt
to the next clicker position. A must have for tuners or anyone that has a TRA clutch!
RW-XPSB : XP Chassis Support Brace - $219.95
Great option for the XP chassis. This product does not only save on the belts,
chassis, and increase hp, the installation will only take 10 minutes. There is no
drilling, cutting, or modifying your chassis to accept the new chassis brace.
Support brace mounts from clutch tower to front of frame. Comes complete
with mounting hardware and instructions.The Product is built from the highest
quality components *lightweight fully polished aluminum main tube *lightweight 6061 aluminum rod ends *billet 6061 aluminum clevis nut
BMP-ETSA : BMP E-Tec Sensor Adaptor - $49.95
Is your E-Tec bogging out on long wide opens pulls since you installed an aftermarket
muffler? The problem is how sensitive the e-tec motor is to heat. The aluminum finned
design disapates heat to aid in cooling the sensor. Plus the simple adapter moves the
sensor out of the extreme heat inside the muffler, allowing your machine to hold maximum RPM all the time. Simple and easy. Threads into your muffler, and simply thread
the sensor into the adaptor.
53
1
66
snowmobile clutch components
67
Arctic Cat/Polaris Primary Springs
Part Number
Color
Rate
Price
05-140-300
Blue
140-300
$29.95
05-160-300
Dark Green
160-300
$29.95
05-170-300
Red
170-300
$29.95
05-160-330
Teal
140-330
$29..95
05-160-330
Pink
160-330
$29.95
05-180-330
Black
180-330
$29.95
TP-210135-001
Green
140-330
$29.95
TP-210135-002
Black/Silver
100-275
$29.95
TP-210135-003
White
120-310
$29.95
TP-210135-004
Red/Black
140-320
$29.95
TP-210135-005
Orange
165-310
$29.95
TP-210135-006
Blue/Black
150-310
$29.95
TP-210135-007
Purple
130-290
$29.95
TP-210135-008
Bright Yellow
120-340
$29.95
TP-210135-009
Bright Green
150-340
$29.95
TP-210135-011
Silver
165-344
$29.95
TP-210135-012
Gold
180-345
$29.95
TP-210135-013
Pink/Black
180-320
$29.95
Arctic Cat Torsion Springs
Part Number
Color
Rate
Price
05-YELLOWTS
Yellow
100-160
$29.95
05-ORANGETS
Orange
120-180
$29.95
Ski-Doo TRA Primary Springs
Part Number
Color
Rate
Price
05-SD-200-300
Yellow
200-300
$29.95
05-SD-160-320
Blue
160-320
$29.95
210141-001
Yellow/Green
160-290
$29.95
210141-002
Yellow/Blue
200-320
$29.95
210141-003
Yellow/Red
200-290
$29.95
210141-004
Yellow/Black
230-350
$29.95
210141-005
Yellow/Orange
230-380
$29.95
210141-006
Yellow/Silver
250-380
$29.95
210141-007
Yellow/White
160-230
$29.95
210141-008
Yellow/Purple
160-260
$29.95
210141-009
Yellow/Light Blue
240-430
$29.95
210141-010
Yellow/Gold
150-240
$29.95
210141-011
Yellow/Pink
200-380
$29.95
210141-014
Yellow/Purple/White
160-380
$29.95
210141-015
Yellow/Black/Green
270-460
$29.95
Ski-Doo QRS Secondary Springs
Part Number
Color
Rate
Price
05-QRSS-205310
Red
205-310
$35.95
05-QRSS-235350
Yellow
235-350
$35.95
Secondary Springs for Team Clutches
Part Number
Color
Rate
Price
05-TP140-240
Red
140-240
$29.95
05-TP140-200
Blue
140-200
$29.95
05-TP160-260
Black
160-260
$29.95
05-TP140-220
Green
140-220
$29.95
05-TP160-240
Purple
160-240
$29.95
68
snowmobile clutch components
Ski-Doo Adjustable Pin Kits
For all Ski-Doo snowmobiles with TRA 2, TRA 3 or TRA 5 primary
clutches. Beware of pin kits tha tare too long to clear the TRA 3 governer cap or have to high of a surface finish. Our pin kits are machined to OEM specs for surface finish and allow full shiftout.
Part #
Weight
13.8-23.2 Grams
$105.95
05-SDPKM
13.8-19.6 Grams
$47.95
05-SDPKL
10.5-15.5 Grams
$47.95
FB-TSR : Oversize Ski-Doo Rollers - $95.95 (Set)
Tune your TRA to perfection with these stock or oversize rollers. Strong construction
will not wear out quickly and roll extremely smooth. Choose from stock (10 gram),
1mm oversize (12.5 gram), or 2mm oversize (15.5 gram). Sold as a set of three.
Ski-Doo TRA 3 Ramps
These ramps are precision machined from billet steel. The shift angles are very similar to SkiDoo, with slight changes. All ramps are lighter than stock and matched in weight for balance.
Part Number
Ramp Profile
Price
TP-TRA3-10001
419 Duplication
$119.95
TP-TRA3-10002
414 Duplication
$119.95
TP-TRA3-10003
412 Duplication
$119.95
TP-TRA3-10004
427 Duplication
$119.95
TP-TRA3-10005
433 Duplication
$119.95
TP-TRA3-10012
410 Duplication
$119.95
TP-TRA3-10013
415 Duplication
$119.95
TP-TRA3-10014
417 Duplication
$119.95
High quality progressive angle helixes for the ski-doo QRS secondary. These
helixes will accept our special smooth shift bearing part number BD-50055.
Part Number
Angle
Price
05-QRS-5040
50-40
$155.95
05-QRS-5042
50-42
$155.95
05-QRS-5038
50-38
$155.95
05-QRS-4944
49-44
$155.95
05-QRS-4943
49-43
$155.95
05-QRS-4743
47-43
$155.95
05-QRS-4742
47-42
$155.95
05-QRS-4640
46-40
$155.95
custom helix angles available
69
Arctic Cat Spider Shims - $19.95
05-SHIM-7040 : Primary clutch spider shim to be used on cat 1100 turbo. this shim will
help the clutch to grab the belt better on the holeshot. It will also make the clutch engage
smoother if your weights are tucked in verses stock.
05-SHIM-8030 : Primary clutch spider shim to be used on cat 600/700/800’s. this shim
will help the clutch to grab the belt better on the holeshot. It will also make the clutch
engage smoother if your weights are tucked in verses stock.
Price
05-SDPKT
QRS Helixes
snowmobile clutch components
BD-50020 : Diamond Drive Rock Rollers - $47.95
Black Diamond’s ROCK Performance Rollers improves clutch performance and shift characteristics. ROCK Performance Rollers are made from engineering grade plastics designed to withstand continuous exposure to elevated temperatures and severe stress conditions. ROCK Performance Rollers low coefficient of friction and ROCK hard compound make ROCK Performance
Rollers the most advanced engineered rollers to date. Made in the USA
BD-50001 : 10.4 TSS Clutch 2005-09 - $294.95
BD-50001-10 : 10.4 TSS Clutch 2010-11 - $294.95
Black Diamond’s 10.4 Conversion Kit produces improved shifting characteristics and
reduced belt slippage. The 10.4 Conversion Kit’s larger outside diameter produces a
lower gear ratio at engagement giving the Diamond Drive even a smoother drive away.
While at the top end the larger diameter allows for more contact surface area with
the belt. The increased contact area minimizes the belt slippage allowing the clutch to
run cooler and more efficient. The 10.4 Conversion Kit comes with factory balanced
sheaves. You utilize the cam, spring and rollers you already own and reassemble with
the new sheaves to complete the clutch. To maximize performance Black Diamond recommends having the assembled clutch balanced at your local dealer. Made in the USA
BD-50001-HD : Heavy Duty 10.4 TSS Clutch 2005-09 - $359.95
BD-50001-10-HD : Heavy Duty 10.4 TSS Clutch 2010-11 - $359.95
Heavy Duty 10.4” Clutch provides 80% more bearing/bushing surface on the moveable sheave, which help reduce wear
commonly associated with stock clutch. Also produces improved shifting characteristics and reduced belt slippage due to
more bearing/bushing support. The 10.4” Clutch comes with factory balanced sheaves. You utilize the cam, spring and rollers you already own and reassemble with the new sheaves to complete the clutch. To maximize performance Black Diamond
recommends having the assembled clutch balanced at your local dealer. Made in the USA
BD-50054 : Arctic Cat Diamond Drive Smooth Shift Bearing - $24.95
Install the slick shift bearing beneath the secondary spring to eliminate binding and free
up power. Get quicker response and increased efficiency out of your secondary by installing this bearing! .***Will not work with Torsional Secondarys***
BMP Sheave Clamp Tool - $12.95
This sheave clamp tool is available for Arctic Cat and Polaris models. This tool holds the
moveable sheave on the primary clutch.This allows you remove the weights without having
to remove the cover, or the clutch. Handy tool is a great combo with our Goldstar magnetic
adjustable clutch weights, or your Stage 2 Clutch Kit! See page 109 for a part number.
BMP Goldstar Magnetic Adjustable Clutch Weights
Our Goldstar adjustable clutch weights are taking over! We developed a weight that is easy to use and easy to tune. This
weight kit allows for easy set up because magnets are used instead of fasteners. No thread lock needed, just a quick snap
in the recessed hole and your done! We have developed what we believe is a far superior ramp profile giving you the best
performance possible for your application. Many weights come bare and will rust over time. These weights all come zinc
plated making them look nicer and last longer. Choose the right weights for your make and model below.
Part Number
Application
Gram Range (Per Arm)
Arms
Price
05-GSW-5571
ARCTIC CAT 2004-PRESENT
55-71 Grams
3
$275.95
05-GSW-5571-4
ARCTIC CAT 2004-PRESENT
55-71 Grams
4
$275.95
05-GSW-6890
ARCTIC CAT 2004-PRESENT
68-90 Grams
3
$275.95
05-GSW-6890-4
ARCTIC CAT 2004-PRESENT
68-90 Grams
4
$275.95
05-GSW-85107
ARCTIC CAT 2004-PRESENT *Big Belly*
85-107 Grams
3
$275.95
05-GSW-90112
ARCTIC CAT 2004-PRESENT WITH RACE NOTCH
90-112 Grams
3
$275.95
05-GSW-5981
POLARIS ALL YEARS / CAT 2003 AND PRIOR
59-81 Grams
3
$275.95
05-GSW-5981-Y
YAMAHA MODELS (INCLUDES PIN CONVERSION)
59-81 Grams
3
$275.95
05-GSW-3552-3
SKI-DOO 4-TEC 2013-PRESENT 3 ARM SET
35-52 Grams
3
$275.95
05-GSW-3552-6
SKI-DOO 4-TEC 2013-PRESENT 6 ARM SET
35-52 Grams
6
$479.95
4 tec and Can Am
MAGNETIC ADJUSTABLE CLUTCH WEIGHTS
snowmobile clutch components
71
Diamond Drive Helixes
We have a full line of our billet helixes. Available progressive cut, multi angle, straight angle, and reverse cut for turbo applications. If you don’t see the angle you want, we can make it for you!
Part Number
Angle
Cut
Price
Part Number
Angle
Cut
Price
05-DD-40-34P
40-34
Progressive
$109.95
05-DD-46-42P
46-42
Progressive
$109.95
05-DD-42-34P
42-34
Progressive
$109.95
05-DD-48-42P
48-42
Progressive
$109.95
05-DD-40-36P
40-36
Progressive
$109.95
05-DD-50-42P
50-42
Progressive
$109.95
05-DD-42-36P
42-36
Progressive
$109.95
05-DD-52-42P
52-42
Progressive
$109.95
05-DD-44-36P
44-36
Progressive
$109.95
05-DD-34S
34
Straight
$109.95
05-DD-46-36P
46-36
Progressive
$109.95
05-DD-36S
36
Straight
$109.95
05-DD-48-36P
48-36
Progressive
$109.95
05-DD-38S
38
Straight
$109.95
05-DD-50-36P
50-36
Progressive
$109.95
05-DD-40S
40
Straight
$109.95
05-DD-40-38P
40-38
Progressive
$109.95
05-DD-42S
42
Straight
$109.95
05-DD-42-38P
42-38
Progressive
$109.95
05-DD-44S
44
Straight
$109.95
05-DD-44-38P
44-38
Progressive
$109.95
05-DD-46S
46
Straight
$109.95
05-DD-46-38P
46-38
Progressive
$109.95
05-DD-38-44R
38-44
Reverse
$109.95
05-DD-50-38P
50-38
Progressive
$109.95
05-DD-36-42R
36-42
Reverse
$109.95
05-DD-44-40P
44-40
Progressive
$109.95
05-DD-40-46R
40-46
Reverse
$109.95
05-DD-46-40P
46-40
Progressive
$109.95
05-DD-34-44R
34-44
Reverse
$109.95
05-DD-48-40P
48-40
Progressive
$109.95
Diamond Drive Helixes
70
snowmobile clutch components
Zinc Plated
Easily Adjustable
Superior ramp Profile
Arctic Cat 2012-Up Torsion Helixes
High quality machined aluminum helixes with a billet adjustable endcap for use with a torsion spring. Compression spring
helixes also available upon request. If you don’t see the angle you want, we can make it for you!
Angle
Cut
Price
Part Number
Angle
Cut
Price
05-PCT-40-36P
40-36
Progressive
$179.95
05-PCT-50-44P
50-44
Progressive
$179.95
05-PCT-42-36P
42-36
Progressive
$179.95
05-PCT-52-44P
52-44
Progressive
$179.95
05-PCT-42-38P
42-38
Progressive
$179.95
05-PCT-46S
46
Straight
$179.95
05-PCT-44-38P
44-38
Progressive
$179.95
05-PCT-46-40P
46-40
Progressive
$179.95
05-PCT-48-40P
48-40
Progressive
$179.95
05-PCT-50-40P
50-40
Progressive
$179.95
05-PCT-50-42P
50-42
Progressive
$179.95
05-PCT-52-42P
52-42
Progressive
$179.95
2012-up cat helixes
Part Number
05-PCT-44S
44
Straight
$179.95
05-PCT-36-44R
36-44
Reverse
$179.95
05-PCT-52-40C
52-40
Compound
$179.95
05-PCT-54-42C
54-42
Compound
$179.95
05-PCT-46-36C
46-36
Compound
$179.95
05-PCT-48-38C
48-38
Compound
$179.95
72
snowmobile clutch components
snowmobile clutch components
73
Dayco XTX Snowmobile Belts
Team Tied Secondary Clutch
Bred from a rich history of experienced belt builders, the new XTX is specifically engineered to maximize the performance
of high horsepower snowmobiles. Beating the competition on the CSRA race course is just one of many aspects that set the
XTX belt apart from its competition. Specially formulated high temperature Polymer along with the highest level of engineered reinforcement proves to perform better in belt operating temperature and efficiency than leading competitors. Its
innovative break-through design of deeper cogs on top and rounded cogs on the bottom yield the advantages of ultimate
flexibility and longer belt life.
TEAM Industries introduces the most advanced driven clutch in the
snowmobile industry.TheTEAMTied Driven Clutch is an improvement
from the TSS-04 in that the moveable sheave opens axially to the
stationary sheave without rotational movement. This translates to no
scrubbing motion on the belt face producing less heat and friction.
Tied features instant backsfhit, cooler running, increased belt life, no
engine reverse clunk, unrivalved torque sensing, and greater efficenty. ***HELIX & SPRING NOT INCLUDED***
Part #
Model
Price
TP-421515
Ski-Doo
$359.95
TP-421511
Polaris
$359.95
TP-451512
Yamaha
$359.95
TP-421896
2012-Up Cat
$359.95
TP-421438
Pre Diamond Drive Cat
$359.95
The Dayco XTX belt offers:
-Tested and proven reliability at well over 12,000 RPMs A cooler-running temperature than the leading competitors
-Faster and more consistent throttle response at high speeds
-Quicker throttle response at mid-speed acceleration
-Greater secondary acceleration at high RPMs
-Greater secondary acceleration as primary acceleration increases
-Reduction in slippage during the highest levels of torque
-Providing more power to track
-Better performance during deceleration (more responsive engine braking)
-Confidence in knowing you’re covered with a one year warranty
XTX HIGH PERFORMANCE BELTS
Team Tied Helixes
Team Tied helixes for Polaris, Ski-Doo, Yamaha & pre diamond drive Arctic Cat models. Procross/Proclimb models
require a different helix however all of the below angles are available. Please use the prefix “AC” infront of the
“96****” in the part number. Example “TP-AC960001”
Here at BMP, we are not easy on belts! We do rigorous clutch
testing and push our machines to the extreme. Finding a good
belt, with close to stock, or at a more fair price than stock isnt
easy! Dayco delivered with these XTX belts. Most models a
slight performance gain has been seen when doing back to
back testing with stock belts. On the Z1 turbo and E-Tec 800
models significant improvements in performance were shown
aswell as much lower clutch temps!
Part Number
Angle 1/Angle 2
Price
TP-960000
73-57.46 ER/73-59 ER
$129.95
TP-960001
80-61.46 ER/80-63.46 ER
$129.95
TP-960002
70-63.46 ER/63 Straight ER
$129.95
TP-960003
61 Straight ER/63 Straight ER
$129.95
TP-960004
76-61.46 ER/76-63.46 ER
$129.95
TP-960005
70-59.46 ER/70-57.46 ER
$129.95
TP-960006
73-63.46 ER/73-61.46 ER
$129.95
Part Number
Make
Model
Price
TP-960007
80-64.46 ER/81-61.46 ER
$129.95
DC-XTX5014
Arctic Cat
2004 440 Sno Pro, Cougar, EXT 580/600
$155.95
TP-960008
63 Straight ER/67 Straight ER
$129.95
DC-XTX5017
Arctic Cat
03-04 F5, 1998 Cougar/EXT 580/600, 2002 Four Stroke
$155.95
TP-960009
66-62.33 ER/66-60.33 ER
$129.95
DC-XTX5020
Polaris
Pro-R & Dragon 600/700/800
$155.95
TP-960010
76-61.46 ER/73-61.36 ER
$129.95
DC-XTX5024
Ski-Doo
Most 03-Up 600s & Many Other Ski-Doo Models
$155.95
TP-960011
73-64.36 ER/73-66.36 ER
$129.95
DC-XTX5025
Ski-Doo
03-07 800 HO/Powertek & 08-11 800R
$155.95
TP-960012
68-63F ER/70-65F ER
$129.95
DC-XTX5028
Arctic Cat
05-06 F5/F6/F7
$155.95
TP-960013
66-62F ER/64-60F ER
$129.95
DC-XTX5032
Arctic Cat
F/M/CFT/Crossfire 800/1000
$155.95
TP-960014
78-63.46 ER/78-61.46 ER
$129.95
DC-XTX5033
Yamaha
Apex/Nytro/Vector/Venture
$155.95
TP-960015
78-65.46 ER/78-63.46 ER
$129.95
DC-XTX5034
Ski-Doo
09-Up XP 600/800 E-Tec & 4-Tec (Significant performance gain seen)
$155.95
TP-960016
73-63.46 ER/73-65.46 ER
$129.95
DC-XTX5035
Arctic Cat
04-05 ZR 900
$155.95
TP-960017
78-63-61 ER/80-65-61 ER (.46/.25/.25)
$129.95
DC-XTX5038
Arctic Cat
09-11 Z1 Turbo (Significant performance gain seen)
$155.95
TP-960018
78-64.46/64-59F, 78-62.46/62-57F
$129.95
DC-XTX5036
Arctic Cat
Sno Pro 500
$155.95
TP-960019
75-57.46 ER/75-59.46 ER
$129.95
DC-XTX5044
Arctic Cat
2012-Up 1100 Non Turbo
$155.95
TP-960020
73-57.46 ER/73-59.46 ER
$129.95
DC-XTX5045
Arctic Cat
2012-Up 1100 Turbo Models
$155.95
DC-XTX5046
Arctic Cat
2012-Up 800cc Models
$155.95
Listed below are the popular belts that we stock. If you do not see your model please go to our website or call. Chances
are we have a belt for your machine!
Supreme Tool Billet
Clutches are
also available
74
arctic cat snowmobile gearing
ski-doo snowmobile gearing
Ski-Doo Gears & Chains
Procross/Proclimb 800 Top Gears
Ski-Doo & Arctic Cat Chains
Highest quality sprockets for Ski-Doo models
High quality gears for your 2012-Up 800 Arctic
Cat models. Some gears may require the use of
a different length chain.
Part Number
75
Highest quality chains for Ski-Doo &
Arctic Cat 13 wide sprockets
Width
Teeth
Internal
Price
Part Number
Width
Links
$ Price
TP-351519-001
13W
18
15T
$49.95
TP-930407
13W
66
$95.95
Ski-Doo Top Sprockets
Width
Teeth
Internal
$ Price
TP-351519-002
13W
19
15T
$49.95
TP-930408
13W
68
$95.95
931065-13
13W
17
19
41.95
TP-351519-003
13W
20
15T
$49.95
TP-930409
13W
70
$95.95
13W
21
15T
$49.95
TP-930410
13W
72
$101.85
TP-930411
13W
74
$101.85
TP-930412
13W
76
$101.85
TP-970417
13W
78
$107.95
TP-970413
13W
80
$107.95
TP-970414
13W
82
$107.95
TP-970415
13W
84
$114.95
TP-970416
13W
86
$114.95
TP-970418
13W
88
$114.95
TP-970419
13W
102
$95.95
TP-970420
13W
104
$95.95
TP-970421
13W
106
$95.95
931065-001
13W
18
19
41.95
TP-351519-004
931065-002
13W
19
19
41.95
TP-351519-005
13W
22
15T
$49.95
931065-003
13W
20
19
41.95
TP-351519-006
13W
23
15T
$49.95
931065-004
13W
21
19
41.95
TP-351519-007
13W
24
15T
$49.95
931065-005
13W
22
19
41.95
TP-351519-008
13W
25
15T
$49.95
931065-006
13W
23
19
41.95
TP-351519-009
13W
26
15T
$49.95
931065-007
13W
24
19
41.95
TP-351519-010
13W
27
15T
$49.95
931065-008
13W
25
19
41.95
TP-351519-011
13W
28
15T
$49.95
931065-009
13W
26
19
41.95
TP-351519-012
13W
29
15T
$49.95
931065-010
13W
27
19
41.95
Ski-Doo Bottom Sprockets
931065-011
13W
28
19
41.95
TP-351520-001
13W
38
17T
$69.95
41.95
TP-351520-002
13W
39
17T
$69.95
TP-351520-003
13W
40
17T
$69.95
TP-351520-004
13W
41
17T
$69.95
TP-351520-005
13W
42
17T
$69.95
TP-351520-006
13W
43
17T
$69.95
TP-351520-007
13W
44
17T
$69.95
TP-352666-13
13W
41
32T
$95.95
TP-352666-01
13W
43
32T
$95.95
TP-352666-02
13W
44
32T
$95.95
TP-352666-03
13W
45
32T
$95.95
TP-352666-04
13W
46
32T
$95.95
TP-352666-05
13W
47
32T
$95.95
TP-352666-06
13W
48
32T
$95.95
TP-352666-07
13W
49
32T
$95.95
MB-XP51
13W
51
32T
$95.95
MB-MZ30T (Uses Stock Chain)
30
$109.95
MB-MZ48T (Uses Stock Chain)
48
$119.95
931065-012
13W
29
19
Diamond Drive Gears
These are one-piece forged precision ground, lite weight gears for your Diamond Drive sled! A wide variety of ratios available, non-reverse(‘04,’05, ‘06 and ‘09) and reverse(‘07-’08). The transfer gears are one piece forged(not welded as OE
04-08) with 5 window openings to provide superior splash lubrication to the rear bearings of the gears which gives longer
bearing life! These gears are a must for any sled over 165hp! Available for models with gear reverse or non gear reverse.
Part numbers ending in “-R” are reverse gears.
Part Number
Gears
Ratio
Price
Part Number
Gears
Ratio
Price
BD-65367-R
53/67
2.83
$269.95
BD-65565
55/65
2.65
$239.95
BD-65466-R
54/66
2.71
$269.95
BD-65763
57/63
2.48
$239.95
BD-65565-R
55/65
2.65
$269.95
BD-65961
59/61
2.32
$239.95
BD-65654-R
56/54
2.54
$269.95
BD-66060
60/60
2.24
$239.95
BD-65763-R
57/63
2.48
$269.95
BD-66159
61/59
2.17
$239.95
BD-65961-R
59/61
2.32
$269.95
BD-66357
63/57
2.03
$239.95
BD-66060-R
60/60
2.24
$269.95
BD-66456
64/56
1.96
$239.95
BD-66159-R
61/59
2.17
$269.95
BD-66555
65/55
1.9
$239.95
BD-66258-R
62/58
2.1
$269.95
BD-66654
66/54
1.83
$239.95
BD-66357-R
63/57
2.03
$269.95
BD-66753
67/53
1.77
$239.95
BD-66456-R
64/56
1.96
$269.95
BD-66852
68/52
1.71
$239.95
BD-66555-R
65/55
1.9
$269.95
BD-66654-R
66/54
1.83
$269.95
BD-66753-R
67/53
1.77
$269.95
BD-66852-R
68/52
1.71
$269.95
BD-65367
53/67
2.83
$239.95
High Torque Gears
For 250+ HP Machines. Must be used with HiTorQ 5 or 6 pinion planetary & Hi-TorQ ring gear.
Part Number
Gears
Ratio
Price
BD-65565-HT
55/65
2.65
$299.95
BD-65763-HT
57/63
2.48
$299.95
BD-65961-HT
59/61
2.32
$299.95
XP Bottom Sprockets
Mach Z Hyvo Sprockets
High Quality Gears and Chains
Part Number
76
snowmobile traction & control
Powermadd Pivot Riser Blocks
Pivot riser blocks are designed to be used on stock “T” style steering posts
or on flat top steering posts with the PowerMadd Pivot Adaptor. If your
sled has a “T” post you can easily raise your bars by replacing the stock
pivot riser with a longer PowerMadd pivot riser. The Pivot riser is tapped
so that is works with your stock handlebar clamps and existing bolts, or the
clamps and bolts provided with the matching PowerMadd Pivot Adaptor
snowmobile traction & control
Rise/Make
Price
PM-15539
2" Arctic Cat/Yamaha
$41.95
PM-15540
2" Polaris
$4195
PM-15541
2" Ski-Doo
$41.95
PM-15527
4" Arctic Cat/Yamaha
$47.95
PM-15528
4" Polaris
$47.95
Part Number Color
Price
PM-15529
4" Ski-Doo
$47.95
PM-14200
Silver/Black
$45.00
4" Yamaha Nytro
$54.95
PM-14201
Ski-Doo Yellow/Black
$45.00
PM-15554
4.5" Narrow Style Polaris
$54.95
PM-14202
Red/Black
$45.00
PM-15530
6" Arctic Cat/Yamaha
$54.95
PM-14203
Green/Black
$45.00
PM-15531
6" Polaris
$54.95
PM-14204
Blue/Black
$45.00
PM-15532
6" Ski-Doo
$54.95
PM-14205
Orange/Black
$45.00
PM-15556
6.5" Narrow Style Polaris
$59.95
PM-14206
Suzuki Yellow/Black
$45.00
PM-15533
8" Arctic Cat/Yamaha
$59.95
PM-14207
Honda Red/Black
$45.00
PM-15534
8" Polaris
$59.95
PM-14208
White/Black
$45.00
PM-15535
8" Ski-Doo
$59.95
PM-14210
Black/Black
$45.00
PM-15558
8.5" Narrow Style Polaris
$64.95
PM-14221
Blue/White
$45.00
PM-15536
10" Arctic Cat/Yamaha
$64.95
PM-14230
Black/Silver
$45.00
PM-15537
10" Polaris
$64.95
PM-14231
Blue/Silver
$45.00
PM-15538
10" Ski-Doo
$64.95
PM-14232
Red/Silver
$45.00
Powermadd Star Series Mount Kit
You’ve got the best guards in the industry, now it’s time to get ‘em on your ride. Our
universal mounting kits install in minutes and gets you on the trail fast. Mounting kits
are made of aluminum brackets, hardened steel straps and stainless steel hardware for
longer life. PM14250 and PM14252 mount near the grip so they will work on standard
7/8” and oversize (1 1/8”) bars. PM14269 works only on 7/8” bars.
Model
Price
Arctic Cat0
PM-15600
38.75"
All 94-02
$60.00
PM-15602
43.5"
03-06 M Series, Sabercat & Firecat
$60.00
PM-15612
43.5"
07-11 M Series
$60.00
PM-15614
57"
12-13 Pro Cross & Pro Climb Chassis
$60.00
35.25"
ZX Models
$60.00
Ski-Doo
PM-15607
Get the ultimate in hand protection for your ATV, motorcycle, and snowmobile with the innovative Star Series Handguard. Remove the vent covers for better airflow, while still blocking branches and debris. Snap the vent cover back in
for cooler weather. Optional accessories include: Snap-in Extensions, Add-on Mirrors, a Hand Wrap Attachment that
provides complete wrap around protection, and cold weather Gauntlets that keep your hands warm and dry.
PM-15564
Ok, now that you’ve got your bars where you want them, your
brake line is too short! Not to worry, we’ve got you covered. Our
braided, stainless brake lines are the answer. They’re coated with
a durable PVC clear coat and at least 6” longer than stock.
Length
Powermadd Star Series Handgaurds
Part Number
Powermadd Extended Brake Lines
Part #
Part Number
Application
Price
PM-14250
Snowmobile
$29.95
PM-14252
ATV & Off Road Motorcycle
$29.95
PM-14269
Tri-Mount Kit (Snow/ATV/Moto)
$29.95
Powermadd Throttle Cable Extension
Now that you’ve raised your bars, you may need to extend your throttle
cable. Our Throttle Cable Extension offers 10” of additional length, plus
an in-line adjuster to fine tune cable tension and slack. Universal ends allow for quick and easy installation on all major brands.
PM-15608
42"
Rev Models
$60.00
PM-15615
42"
Rev XP Models
$60.00
Part Number
Application
Price
PM-15604
36.75"
All Through 05 Except Pro-X & IQR
$60.00
PM-14250
Arctic Cat (Pre 2007), Polaris, Ski-Doo
$35.95
PM-15605
41"
All Pro-X & All 06-Up Except 09-10 RMK Dragon, 09-13 Assault, 11-13 Pro RMK, IQR & IQRR
$60.00
PM-14252
Yamaha 4 Strokes
$35.95
PM-15611
36.5"
09-10 RMK Dragon, 09-13 Assault, 11-13 Pro RMK, IQR & IQRR
$60.00
PM-43596
Arctic Cat 2007-Up (Complete Cable - 2 Stroke Models ONLY)
$49.95
PM-15616
37"
00-01 Gen II & 00-03 RMK
$60.00
37"
97-03 SX, Venture, V-Max, Mountain Max & Viper
$60.00
Polaris
Yamaha
PM-15609
77
PM-15610
43.5"
03-04 RX, 05 Rage, 06-13 Venture, 05-07 Vector & 07-13 Phazer
$60.00
PM-15611
36.5"
05 RX, 06-07 Rage, 06-13 Apex, 06-07 Attak, 07 Nytro & 08-13 Vector
$60.00
PM-15613
51"
08-13 Nytro FX, RTX & XTX
$60.00
PM-15614
57"
08-13 Nytro MTX
$60.00
PM-15701 : Powermadd Sure Grip Traction Strips - $24.00
- Strips are 2” long x 1.25” wide x .5” tall. Includes 8 strips and 16 mounting rivets.
- Enough for both sides of a standard sled. Mountain sleds require additional Sure Grips.
- Compact design allows easier positioning on the complicated snowmobile running boards.
- Works great on Utility ATV floor boards.
Note! May not work on sleds with cooling systems under the running boards.
snowmobile traction & control
78
Oversize Handlebars
High quality handlebars much stronger than stock! Choose from the following Fly or BMP handlebar designs. 1-1/8” clamp size. May require
oversize clamp kit. BMP Bars are same construction as Fly!
Part Number
Description
Price
WPS-18-95297
Fly Sno-X Race Bar w/Hooks
$144.95
WPS-18-95296
Fly Sno-X Bars
$89.95
WPS-18-95270
Fly Mini Bar
$89.95
WPS-18-95298
Fly Mountain Bar
$89.95
BMP-HPB
BMP Straight Bars
$59.95
BMP-MB
BMP Mini Bars
$59.95
snowmobile traction & control
79
Stud Boy Kwik Pixx Improved Stud
Our “Kwik Pixx Improved” has enhanced the original “Kwik Pixx” by enlarging the head size to .875”, and the shank size
to 5/16”. The larger head size offers “STUD BOY”® “Track Trapping” head design that provides greater support. Available in three (3) lengths, the “Kwik Pixx Improved” includes lock-nuts. Recommended for competition use only.
Part #
Description
Price
SB-2236-P2
KWIK PIXX IMPROVE 1.000"
$2.05ea
SB-2237-P2
KWIK PIXX IMPROVE 1.080"
$2.05ea
SB-2238-P2
KWIK PIXX IMPROVE 1.200"
$2.05ea
kwik pixx
WPS-59-8892 : ODI 8” Grips - $24.95
These ODI grips are nice and long to cover your handwarmer elements and
handlebar hooks. Diamond grey pattern is comfortable and provides positive grip.
Sold as a set in grey.
WPS-18-9498 : Fly Oversize Clamp Kit - $54.95
Required when adding 1-1/8” aerotaper style bars to your sled or other machine. Universal
mount fits most sleds and adds a 3/4” rise. Comes with a black bar pad.
Extreme Max Platinum Series Studs
Our Extreme Max Platinum Series Studs are constructed out of top of the line materials and completely manufactured in
America. The stud bodies are constructed from hardened military grade stainless steel so you know they are built to last.
These snowmobile studs are designed with a two-step inert gas heat treatment process. This allows for a 30% increase in
abrasion resistance and a 25% increase in bend resistance to better provide you with the traction you need. Extreme Max
snowmobile studs also feature an 80 degree carbide insert tip which provides ultra-high impact and abrasion resistance.
Plus with the exclusive taper profile there is maximum protection of the carbide insert. One of the best features of our
Extreme Max Platinum Series Studs is that they have a full 1” head design which provides up to 36% more track contact
area than other brands. This creates more traction and greatly reduces the risk of stud pull-thru which is a constant battle
on today’s high power machines. Another great aspect of the 1” head design is that they sit flush with the track so you can
maneuver your snowmobile freely without any chatter. Finally the Extreme Max Platinum Series Studs feature a Torx Drive
Head. The Torx Drive head is over 30% stronger than the out of date hex drive design. This drive resists stripping and
makes the critical base area stronger and much more resistant to breakage. Finally, along with all of these great features,
Extreme Max also provides a Two Year No-Hassle Bend/Break Warranty. Standing behind our product is very important.
Stud Boy Assassins Improved Drag Stud
The Assassins Improved are new & improved with more aggressive design. Assassins Improved” features all the same great
benefits as our original “Assassins”, with a larger head size to offer “STUD BOY”® “Track Trapping” head design for great
support, and 5/16” tapered shank that gives superior rigidity. Available in six (6) lengths, the “Assassins Improved” includes
lock-nuts. Recommended for competition use only
Part #
Description
Price
SB-2233-P2
ASSASSIN IMPROVED 1.00"
$2.15ea
SB-2234-P2
ASSASSIN IMPROVED 1.08"
$2.15ea
SB-2235-P2
ASSASSIN IMPROVED 1.20"
$2.15ea
SB-2460-P2
ASSASSIN IMPRVD; 1.375"
$2.15ea
SB-2465-P2
ASSASSIN IMPRVD; 1.500"
$1.1ea
SB-2466-P2
ASSASSIN IMPRVD; 1.625"
$1.80ea
SB-2497-P2
ASSASSIN IMPRVD; 1.875"
$.80ea
assassins
Stud Boy Power Tower Support Nuts
The Power Tower Support Nuts offer extra support to eliminate stud bending and
breaking without any additional weight. Developed by the demands of aggressive
riders and rising lug heights.
Part #
Description
Price
SB-2434-P1
POWER TOWER LOCK NUT .750"
$0.55ea
SB-2438-P1
POWER TOWER LOCK NUT .500"
$0.55ea
Stud Boy Hillclimb Ice Screws
Part Number
Overall Length
Price
NW-5001.5309
1.00”
$1.85ea
NW-5001.5324
1.25”
$1.85ea
NW-5001.5339
1.35”
$1.85ea
NW-5001.5355
1.45”
$1.85ea
Part #
Description
Price
NW-5001.5370
1.65”
$1.85ea
SB-HILL-P4
HILLCLIMB 1" SCREW QTY 250
$35.95
NW-5001.5385
1.75”
$1.95ea
NW-5001.5400
1.95”
$1.95ea
SB-HILL-P5
HILLCLIMB 1" SCREW QTY 1000
$138.95
SB-HILL-P7
HILLCLIMB 1" SCREW QTY 500
$70.95
ISR legal, this “Snowmobile Hillclimb/Ice Screw” features a large hex head with a ball milled center for an aggressive bite in all conditions. “Hillclimb/Ice Screws” available in a 1.000” thread in three (3) quantity packs.
snowmobile traction & control
80
INS Stinger Studs
Our INS STINGER Studs are better than the Hornet Ice Studs we invented over 10
years ago. And, we can back it up... We guarantee* our Ice Studs against breaking
or bending.* No other snowmobile studs do that. We’ve kept the best features of
the hornets and we’ve added some features and the guarantee.
Our Favorite Trail Stud!
* The narrow hornet profile and rimless tip reduce float and improve bite
* Rotation ribs eliminate spinning and/or loss of orientation
* Larger, thin head makes flush installation easier
* 5/16 diameter shank for strength and durability
Part Number
Overall Length
Price
INS-HIP-1.08
1.440”
$2.54ea
INS-HIP-1.18
1.540”
$2.56ea
INS-HIP-1.34
1.690”
$2.63ea
INS-HIP-1.52
1.830”
$2.70ea
INS-HIP-1.64
1.950”
$2.79ea
Price
INS-FAT-1.18
1.54”
$3.20ea
INS-FAT-1.34
1.69”
$3.20ea
INS-FAT-1.52
1.83”
$3.40ea
The Extreme Max Double Stud Backer is built tough and is a favorite with all of the pros.
Designed by our Extreme Max engineers this double stud backer allows you to install two
studs for less weight than two individual stud backers. It provides excellent versatility by
creating new options for studding in the middle of your snowmobile belt. Backed by our Extreme Max 2 Year Full Replacement Warranty this double stud backer is designed to handle
two snowmobile studs. 1-1/4” x 2-1/4”, .180 thickness. Works on any 5/16” stud.
• 1-3/8” Diameter x 1/4” Tall
• 0.140 material thickness
• Works on any 5/16” stud
• Premium heat-treated aluminum
• Two Year Full Replacement Warranty
CALL FOR BULK
STUD DISCOUNTS
These studs are built for the high-performance sleds with single ply tracks. We’ve
taken our STINGER Studs and made them with a larger 1.20 diameter head to spread
out the forces on the snowmobile track. Fathead Ice Studs have all the features of our
regular ice studs and we’ve added the larger head. And they’re guaranteed.
Overall Length
NW-5900.5603 : Extreme Max Double Stud Backer - $1.15ea
NW- 5900.1133 : Extreme Max Round Aluminum Backers - $0.65ea
INS Fatheads Studs for Single Ply Tracks
Part Number
snowmobile traction & control
NW-5001.5069 : Extreme Max Square Aluminum Backers -$0.55ea
• 1-1/8” Square x 1/4” Tall
• 0.140 material thickness
• Works on any 5/16” stud
• Premium heat treated aluminum
• Two Year Full Replacement Warranty
SB-2193-P5 : Stud Boy Power Plate Single Backer - $0.72ea
The “Power Plate” Backer is the industries best backer! This innovative shape provides great stud
support and is almost unbendable. We added a radial lobe to a standard 1.125” backer by
reducing wear and tear on the track and increasing stud rigidity. By decreasing the weakest flat
corner area of the square backer we have reduced unnecessary weight and bending of the corners for a super strong design. Light-weight and durable, use the “Power Plate” aluminum backer
and receive the best benefits of both square and round backers in one design!
RTS Icemasters Screw-In Track Studs
SNOWMOBILERS: With our Icemaster Screw-In Track Studs you can get lateral traction, acceleration and braking for your
sled without drilling your track. The large 70 degree carbide tips really dig in. They’re the largest in the industry and will
last for several seasons. Icemasters are easy to install – they screw into the top of the lug for best bite and they require no
drilling. Installation takes less than 1 hour and requires only a 5/16 socket and cordless drill. With today’s high profile
tracks, push-thru studs have to be longer and heavier which increases their cost, weight and rotating mass. The increased
weight also increases the stress on the track. Because they’re so long, push-thru’s flex more. Our Icemasters, mounted on
the top, in the thick part of the lugs, are a lot more rigid. This provides better bite and more positive traction control. HILLCLIMBERS – add these to your deep-lug paddle tracks for extra traction on those icy spots. You’ll love the extra bite!
Part Number
Application
Thread Length
Quantity
Price
INS-RTS-2-100
For Lugs Less Than 1”
1/2”
100
$192
INS-RTS-2-250
For Lugs Less Than 1”
1/2”
250
$415
INS-RTS-3-100
For Lugs 1” to 1.25”
3/4”
100
$192
INS-RTS-3-250
For Lugs 1” to 1.25”
3/4”
250
$415
INS-RTS-4-100
For Lugs over 1.25”
1”
100
$192
INS-RTS-4-250
For Lugs over 1.25”
1”
250
$415
INS-SR-31
Icemaster Install Tool
N/A
N/A
$11.95
SB-2266-P2 : Stud Boy Power Plate Aluminum Double Backer - $1.38ea
The #1 choice of many snocross racers and aggressive trail riders, this ISR legal aluminum
double backer features light-weight rigid mounting for two (2) 5/16” studs. This durable
design is lighter than two (2) aluminum single backers, and allows for extra scratchlines when
studding for aggressive performance.
SB-2439-P1 : Stud Boy Power Plate Plus Single Backer - $0.84ea
SB-2499-P1 : Stud Boy Power Plate Plus Double Backer - $1.85ea
STUD BOY”® announces our new “Power Plate Plus” Backer. This new “Power Plate Plus Backer” is designed for new Ski-Doo XP sleds, as well as the new Camoplast Single Ply Tracks. Our
lightweight and durable shape features our innovative design for stud support. The “Power
Plate Plus Backer” is to reduce wear and tear on tracks, and receives the best benefits of both
square and round backers. (Available in one design)
81
snowmobile traction & control
82
Curve Performance Ski’s
At BMP we could not believe the increased handling performance of this ski! Curve’s XS Ski Features : An exclusive profile that forms and compresses snow into rails under the snowmobile ski. The complex geometry on top of the snowmobile
ski serves double duty as spindle mount and deflection control. A variable loop cross section allows the snowmobile ski tip
to flex without impeding its movement. The loop to ski locking mechanism ensures a tight, hassle free connection. Studboy
2198 Series 17” host bar, 4 stud pattern carbides. Snow-Studs RM78 Series 4”, 6”, 8” and 10” Carbides Curve Xtremes
are offered with a custom engineered hardware system that consists of choice grade zinc plated carbon and stainless steel
fasteners. Carbides Sold Separately.
snowmobile traction & control
83
CI-XS-400-2 : Curve Leading Edge - $114.95
The leading edge was developed to address slow speed and deceleration tracking on rutted hard packed or icy trails.
This adverse condition is one that has plagued single runner skis until now, because with an LE installed, the hard surface
doesn’t stand a chance. Through a full season of testing, the fundamental finding was not to use more wear bars, but simply
control the one already employed. With its aggressive keel approach angle and ingenious design, the machine ignores ruts
and does not allow the carbide to find a path other than the one being made by the LE. The following are performance
enhancements realized by the installation of a Leading Edge: Perfectly straight tracking in all conditions, on all chassis, at
any speed, zero reduction in top speed, zero increase in steering effort, The ability to run any standard wear bar while
the LE is installed Permission of the ski to maintain its flexibility characteristics, aids as a first line of defense against foreign
object impacts which could otherwise cause wear bar damage Sold as a pair and comes with installation template.
CI-ST-101 : Curve Industries Thruster - $95.95
The Curve Thruster is a bolt-on handling performance product that is available for the Curve XS along with the most popular aggressive trail, crossover and mountain OEM skis. The Thruster takes only minutes to install by using the spindle bolt,
plus one bolt forward and aft which hold it firmly to the outside of the ski. Once installed, the rider will notice increased
cornering performance in soft trail conditions, as well as greater flotation and a more aggressive and balanced feel off
trail during side-hill and carving maneuvers. The Thruster is ultra light weight and constructed from the same durable, long
lasting UHMW plastic found in our skis. Choose between trail or mountain series. For more options please call or go online.
Curve Ski Hardware Kits - $49.95
Model
Part Number
Arctic Cat CFR/Firecat
XS-306-1
Polaris Edge
XS-306-2
Polaris IQ/Fusion
XS-306-3
Ski-Doo DSA
XS-306-4
Ski-Doo Rev/XP
XS-306-5
Yamaha Standard
XS-306-6
Yamaha Phazer/FX Nytro
XS-306-7
Arctic Cat 2010-11 CFR/M
XS-306-8
Arctic Cat 07-09 Twin Spar
XS-306-9
Arctic Cat 2010-11 Twin Spar
XS-306-10
Arctic Cat 2012+ Pro Chassis
XS-306-11
Polaris Pro-R Chassis
XS-306-12
Stud Boy Shaper Bar Carbides
The “Shaper”™ Bar takes the wearbar design and performance to a new level! This bar offers a unique shape that provides much better turning than conventional bars and offers a 20% weight savings too! The concave side profile on the
“Shaper”™ Bar grabs and holds snow rather than allowing snow to slip by like other wearbars. While the shape of this
bar improves the turning radius of your sled on the trail, the large 60º carbide provides great control and wear on hard
surfaces. Zinc plated to resist corrosion and eliminate paint in threads. This is the recommened bar for the Curve XS ski’s!
Please call to order for specific makes and models.
Length
Price
00”
$83.95
4.5”
$99.95
6.0”
$114.95
7.5”
$131.95
9.0”
$137.95
84
snowmobile misc
Brite Lites Xenon High Performance Headlight Bulbs
Our industry leading Xenon Gas Brite Lite brand of headlight bulbs are the number one name in the snowmobile market
and for good reason- we are true snowmobilers and test every product we sell on the real thing- SNOW!! We log miles
every year like any other snow junkie, chasing the last snowfall, taking in a race, and driving out to the mountians to get it
steep and deep! With our travels, we have developed the largest line of lighting for your needs no matter what keeps you
from your full potential. we have Brite Lites that improve near feild problems like snow dust and fog, we have Brite Lites
that can double your Hi-beam length and width by using the state of the art Xenon Gas Blues like the european and luxuary cars with HID lighting.
Model
Parts Included
Price
Ski-Doo 1998-Up
Two H4 Bulbs
$32.95
Yamaha 2001-Up
Two H4 Bulbs
$32.95
Polaris 2001-2010 (Not Pro-R Chassis)
Two H4 Bulbs
$32.95
Polaris Pro-R Chassis 2010-Up
Two H14 Bulbs
$32.95
Arctic Cat Pro Chassis 2012-Up
Two H4 Bulbs
$32.95
Arctic Cat M/X-Fire Chassis
Two 13B502 & Two 13BS50 Bulbs
$72.95
Arctic Cat Twin Spart Chassis
Two H11 & Two 13B502 Bulbs
$64.95
Arctic Cat Firecat
Four 13B502 Bulbs
$64.95
Arctic Cat ZR Chassis
Two 13B502 & One BL-13BS50 Bulbs
$52.95t
snowmobile body
85
Racewerx 2012-Up Arctic Cat Front Bumpers
Get rid of that cheesy stock front bumper and install this heavy duty,
lightweight & trick billet bumper from Racewerx. Choose from the
standard version or the mountain version! Will fit 2012-Up Arctic Cat
Procross/Proclimb chassis sleds along with the 2014 Yamaha Viper.
Part Number
Description
Price
RW-100-301-SPFB-BK
2012-14 Arctic Cat Trail Front Bumper - Black
$359.95
RW-100-301-SPFB-WH
2012-14 Arctic Cat Trail Front Bumper - White
$359.95
RW-100-301-MSPFB-BK
2012-14 Arctic Cat Mountain Front Bumper - Black
$455.95
RW-100-301-MSPFB-WH
2012-14 Arctic Cat Mountain Front Bumper - White
$455.95
BL-DIS : Duraflex Ice Scratchers - $95.95
# COMES STANDARD WITH CARBIDE TIPS (Replacement Tips $34.95)
# ULTIMATE ENGINE COOLING AND SLIDER LUBE
# UNMATCHED PERFORMANCE AND WEIGHT
# WORKS WITH ALL REVERSE AND NON-REVERSE GEAR EQUIPPED SNOWMOBILES
# PRE-ASSEMBLED FOR ONE-BOLT MOUNTING
# VIRTUALLY INDESTRUCTIBLE ZINC-PLATED WIRE ROPE FOR INCREASED DOWN PRESSURE AND NO COATING TO CRACK AND PEEL
# IMPROVED CRIMPS FOR GREATER HOLD
# HOOKS AND STAYS ON RAILS WHEN NOT IN USE
# KNURLED MOUNTING SURFACE ELIMINATES SPINNING AND LOOSENING ON THE RAIL
BL-TL : Track Link Limiter Strap Adjuster - $89.95
TRAC-LINK™ is a new innovation aimed at giving you the ability to adjust traction and balance characteristics of your any make/model snowmobile quickly
and easily.TRAC-LINK™ replaces the OEM limiter-straps with an ultra-strong
Goodyear® strap combined with with the Patent-Pending aluminum adjustment
mechanism to give you 3 full inches of infinite adjustment with a simple turn of a
1/2” or 13mm wrench.TRAC-LINK™ weighs just 15oz including the strap and all
necessary hardware and is adaptable to any rear suspension that employs conventional limiter-straps*. Does not fit Yamaha® Mono-shock® rear suspensions.
Modification needed on 2007-2010 Polaris® Dragon®.
Quick Click Suspension Blocks - $47.95
These strong, light suspension blocks will not break or strip like
the plastic stock units. Four sided adjust ability with the turn of a
wrench to fine tune your ride. Packaged in pairs, please indicate
which model you have.
BDX Pro-Lite Cat 2012-Up / 2014 Yamaha Viper Front Bumpers
Timg to get a real bumper on your sled! This makes it much easier to move around,
and extremely helpful if you get stuck. Not to mention much better protection on your
2012-up 800 or 1100 Turbo cat. Choose your color below!
Part Number
Description
Price
BD-20075-BL
BDX 2012-14 Pro-Climb/2014 Yamaha Viper Pro Front Bumper - Black
$239.95
BD-20075-GR
BDX 2012-14 Pro-Climb/2014 Yamaha Viper Pro Front Bumper - Green
$239.95
BD-20075-OR
BDX 2012-14 Pro-Climb/2014 Yamaha Viper Pro Front Bumper - Orange
$239.95
BD-20075-WH
BDX 2012-14 Pro-Climb/2014 Yamaha Viper Pro Front Bumper - White
$239.95
BDX Pro-Lite Arctic Cat 2012-Up / 2014 Yamaha Viper Running Boards
Strong, lightweight running boards that don’t collect snow! Excellent traction for your feet. These require cutting of OEM
running boards. Fit all Procross/Proclimb chassis sleds and the 2014 Yamaha Viper. For more details and images log on
to bikemanperformance.com
Part Number
Description
Price
Part Number
Model
BD-20080-BL
BDX 2012-14 Pro-Climb/2014 Yamaha Viper Pro Running Boards - Black
$479.95
DP-QCSB-A
Arctic Cat
BD-20080-GR
BDX 2012-14 Pro-Climb/2014 Yamaha Viper Pro Running Boards - Green
$479.95
DP-QCSB-S
Ski-Doo
BD-20080-WH
BDX 2012-14 Pro-Climb/2014 Yamaha Viper Pro Running Boards - White
$479.95
DP-QCSB-P
Polaris
BD-20080-OR
BDX 2012-14 Pro-Climb/2014 Yamaha Viper Pro Running Boards - Black
$479.95
PRO-LITE
RUNNING
BOARDS
86
snowmobile intake
Boyesen Rage Cages
MAXIMUM POWER ACHIEVED THROUGH AIR INTAKE, ACCELERATION AND DISTRIBUTION : BOYESEN engineers embarked on a mission to create a new lineage of aerodynamic intake technology by refining the primary performance factors required to increase peak horsepower through design innovation: Aerodynamic Surface Optimization, Model-Specific
Reed Petal Tensioning, Material Fuel Resistance, and Multi-Stage Reed Timing. Together, these innovations create a new
technological benchmark in intake performance. The next generation Rage Cage RC2 series results in an optimized reed
valve system that provides superior efficiency, peak horsepower gains, and acceleration for YOUR specific model sled.
PRECISION CASTING : Your engine is a glutton for air. It will take over 200 "gulps" per second, at velocities over 500 MPH
- if your intake valve will let it. The Rage Cage's seamless, one-piece, precision casting and continuous aeroform surfaces
ensure maximum flow velocities and instant, explosive movement of air particles the moment you open the throttle. Result: An
intake valve the size of your fist delivers air with the power of a tornado.
POWER CHANNELED AIR CHARGE : Integrated into the seamless inner chamber are 4-way aerodynamic directional dividers that distribute the angled charge evenly without flow loss. Each channel has its own unique Power Profile, scientifically
shaped to produce instant, explosive movements of air. Result: Unparalleled performance.
INTELLIGENT MULTI-STAGE REED PETAL SYSTEM : Standard equipment on each Rage Cage, Boyesen dual-stage, Pro Series
Reeds have the superior ability to time themselves to the needs of the engine. You get maximum flow velocity across the
entire RPM range, and at all throttle settings. Smooth. Sharp. Smart. Result: Full Spectrum power and throttle response.
OPTIMIZED FOR EACH MAKE/MODEL/YEAR SLED : Each Boyesen Rage Cage is unique - tailor made to that model, year
and displacement. While other aftermarket valves might change flange sizes or bolt patterns, they’re basically generic and require you to irreversibly cut your intake boot to install it! But with the Rage Cage, there are no compromises in power,
no modifications. Result: A true, bolt-on Power Boost.
snowmobile intake
87
New XP 800R Rage Cages
Rev 600/800
F/M/X-Fire 1000
REEDS YOU CAN COUNT ON FOR LONGEVITY AND PERFORMANCE
2010-Up Arctic Cat 800HO
Boyesen Rage Cages
Part Number
Make
Model
Year
HP
Price
BY-RAD86-2
Ski-Doo
600 SDI
2004-07
2-3
$429.95
BY-RAD84-2
Ski-Doo
Rev 600/800 Carb ***Intake Boot Built In***
2003-07
2-3
$369.95
BY-RAD85F-2
Ski-Doo
XP 800R
2008-11
5-6
$379.95
BY-RAD88-2
Ski-Doo
E-Tec 800
2011-14
3-4
$379.95
BY-RAD87-2
Ski-Doo
1000 SDI
2005-07
4-5
$449.95
BY-RAD51A-2
Arctic Cat
Sno Pro 440
2003-06
2
$329.95
BY-RAD51-2
Arctic Cat
F/M/CFR 500/600/700 Carb & ZR 800/900 Carb
Varies
2-3
$329.95
BY-RAD51C-2
Arctic Cat
F/M/CFR 500/600/700 EFI & ZR 800/900 EFI
Varies
3-4
$347.95
BY-RAD53-2
Arctic Cat
800 HO
2010-14
4-5
$384.95
BY-RAD50A-3
Arctic Cat
All Triples
All
3-4
$442.95
BY-RAD52-2
Arctic Cat
F/M/CFR 1000 or (800 with 50mm Throttle Bodies)
All
3-4
$395.95
BY-56A-2
Arctic Cat
F/M/CFR 1000 with 56mm Throttle Bodies
All
3-4
$455.95
BY-RAD65-2
Polaris
All 500/600/700/800 Twins
All
3-4
$329.95
BY-RAD65-3
Polaris
All Triples
All
3-4
$443.95
BY-RAD67-2
Polaris
Fusion 700/900
2005-06
2-3
$395.95
BY-RAD67A-2
Polaris
800 CFI
2008-14
2-3
$395.95
snowmobile intake
88
snowmobile intake
89
Timbersled Air Intakes
V-Force 3 Reed Cages
Moto Tassinari’s V-Force 3 Reed Valve System features a patent pending reed tip shape that accelerates the air mixture
over the reed tips for even more airflow and horsepower. Applying this technology to their already incredibly successful double v-block reed cage design, which doubles the reed tip surface area allowing more airflow with less reed petal
movement, theV-Force 3 increases efficiency throughout the entire powerband.This results in explosive acceleration, sharper throttle response, improved fuel economy and significant horsepower gains. Reed Valve Kits include complete cages with
pedals, stops and gaskets.
These kits save weight and substantially reduce under hood height by eliminating large plastic air boxes and hardware
that the OEM uses. This frees up under hood space and increases air flow through the engine compartment. All kits use a
snow cone air filter that is shaped like a velocity stack. This increases airflow to the engine giving it an increase in throttle
response and top end HP. The kit also properly mounts the intake sensors giving the engine proper tuning without having to
re-jet or re-map the fuel system.
Arctic Cat
X-Fire/M
Excellent Power
Crisp Throttle Response
Carbon Fiber Pedals
Part #
Model
Year
Price
VF-3112-873B-2
Arctic Cat F/M/X-Fire 6/6/7/800
2003-11
310.00
VF-3112-904-2
Arctic Cat F/M/X-Fire 1000
2007-11
310.00
VF-3112-873B-2
Sno Pro 440,
Sno Pro 500,
ZL/ZR 800/900
2003-08
All
All
310.00
VF-3132-873F-2
Polaris 6/7/800 CFI
2006-14
310.00
VF-3122-873J-2
Ski-Doo E-Tec 800
2010-14
310.00
VF-3127-873A-2
Ski-Doo Rev XP 600SDI/600 E-Tec
2008-14
319.00
VF-3122-873I-2
Ski-Doo Rev XP 800R
2008-11
385.00
Polaris IQ
700-900
Polaris IQ
6/7/800
Ski-Doo XP
with DPM
Ski-Doo Rev
600 & 800
Ski-Doo
Summit 1000
Part #
Model
Year
Lbs Lost
Items Included
$ Price
TS-1
M/CFR
05-11
8
Intake Manifold, ECU Mounting Bracket, 2 Filters, 2 Pre Filters, 5 improved Hood
Screens
330.00
TS-2
IQ 700/900
05-06
7
Intake Manifold, Air Filter, Pre Filter, Clutch Cover
300.00
TS-3
IQ 6/7/800
07-10
0
Intake Manifold, Air Filter, Pre Filter, Intake Screens
275.00
TS-4
XP 800
08-11
4
Intake pod cover, 2 air filters, 2 pre filters, headlight mounting bracket, 2 side panel
screens. *NOT E-TEC*
330.00
TS-5
Rev 6/800
04-07
4
Intake air cover, 2 air filters, 2 side panel screens (screens are black) & Carb.
mount
300.00
TS-6
RT 1000 SDI
05-07
4
Intake air cover, 2 air filters, 2 pre-filters, 2 side panel screens (screens are black)
& Carb. mount
300.00
90
snowmobile intake
BL-1107-PA2 : POWAIR 2” Vent - $14.95ea
BL-1108-PA3 : POWAIR 3” Vent - $17.95ea
POWAIR vents are a simple install and eliminate bogging in deep powder. Vacuum operated to open only when more air is needed. Plastic/rubber composition will not stick or
freeze. Made in the USA.
SLP Flow Rite Vents - $24.95ea
Eliminate air intake restrictions by installing the Flow-Rite™ into the dash for more airbox
feed. The Flow-Rite™ is supplied with a powder snow pre-filter that repels snow and water, yet passes air right through. A must for modified sleds. Sold per each.
- SLP-14-189 : The 2.5” rubber flange flow rite is made using a rubber flange to attach
the Flow-Rite™ to the surface that it is being installed in. This rubber flange conforms itself
to a wide variety of contoured, shaped and textured surfaces for a universal mounting
system. This Flow-Rite™ has an outside diameter of 3 5/8” and requires making a 3 1/8”
diameter hole for installation.
- SLP-14-194 : The 2” rubber flange flow rite is made using a rubber flange to attach the
Flow-Rite™ to the surface that it is being installed in. This rubber flange conforms itself to
a wide variety of contoured, shaped and textured surfaces for a universal mounting system. This Flow-Rite™ has an outside diameter of 2 11/16” and requires making a 2 3/8”
diameter hole for installation.
- SLP-14-197 : The 2” Snap In Flow Rite is designed for ease of installation on flat or
nearly flat surfaces. It requires a 2 1/2” size hole saw which is readily available from any
hardware store. Installation is a snap: hole saw the hole, debur the edges, clean hole saw
shavings and snap Flow-Rite™ into place.
FL-MSV : Fastlane M Series Vent Kits - $119.95
Reduce under hood temperatures with these attractive side vent kits! High under hood temps can
lead to extremely hot clutches and premature belt failure. This is the answer to that problem!
These side vent kits consist of a rigid thermoplastic material with high impact resistance for the
ultimate in strength and flexibility. The nylon/kevlar screen is very strong, which will resist punctures. It will allow cool air in, hot air to escape, yet will not allow snow to enter. This inexpensive
kit consists of vents for both RH and LH side panels, all fasteners and detailed instructions.
FL-FV-SDBLK : Fastlane XP Side Panel Vent Kit - $119.95
Reduce under hood temperatures with these attractive side vent kits! High under hood temps can
lead to extremely hot clutches and premature belt failure. This is the answer to that problem!
These side vent kits consist of a rigid thermoplastic material with high impact resistance for the
ultimate in strength and flexibility. The nylon/kevlar screen is very strong, which will resist punctures. It will allow cool air in, hot air to escape, yet will not allow snow to enter. This inexpensive
kit consists of vents for both RH and LH side panels, all fasteners and detailed instructions.
FL-FV12 : Fastlane Procross/Proclimb Side Panel Vent Kits - $119.95
Reduce under hood temperatures with these attractive side vent kits! High under hood
temps can lead to extremely hot clutches and premature belt failure. This is the answer to
that problem! These side vent kits consist of a rigid thermoplastic material with high impact
resistance for the ultimate in strength and flexibility. The nylon/kevlar screen is very strong,
which will resist punctures. It will allow cool air in, hot air to escape, yet will not allow snow to
enter. This inexpensive kit consists of vents for both RH and LH side panels, all fasteners and
detailed instructions. Available in white or black.
snowmobile intake
DD-700-0014 : Bullseye Air Intakes : $47.95
D&D Bullseye Air Intakes are great for any airbox; snowmobile, ATV, truck, or car. The principle is simple:
more air = more power. Just drill a 1 1/2” hole and press in for more air flow. In most cases adding
performance parts such as pipes, reeds, or big bores makes the stock air box insufficient. By adding the
Bullseye Air Intakes you can greatly improve air flow. The intakes come in a pack of six. Black only.
BD-50044 : Black Diamond Black Boxx Intake - $199.95
This cold air intake system removes 8 lbs of unwanted weight from OE intake system. Exclusive air mesh filtering and chamber separator to give you filtered and separated cold
air from underhood engine heat.Will fit all 05’-UP M’s and Crossfire’s. Will also fit 03-06
Firecats. A must for any big bore engine and for the serious mountain rider.
BD-20066 : 2012-Up Arctic Cat Intake w/ Head Light Delete - $479.95
BD-20067 : 2012-Up Arctic Cat Intake w/o Head Light Delete - $419.95
All new cold air intake for 2012-Up Arctic Cat’s With stock headlight 10Ilb lighter than stock.
With headlight delete intake is 12lbs lighter than stock. Complete and ready to bolt on! This
intake is a great addition to your BMP Bolt-On parts!
BD-50044-VENT : BDX 9 Piece Vent Kit - $95.95
9 Piece Vent Kit - Damage to your existing screens? Built your
own airbox? Use this 9 piece vent kit!
BD-50044-HOOD : BDX Hood Screens - $23.95
Hood Vents - Getting snow under your hood from the forward
hood vents? Use the BDX Hood Vents!
SLP-14-307 : High Flow Intake Pro-R Chassis - $72395
This High Flow™ Intake significantly increases air intake surface area for better airflow
to the engine. It provides additional air in a protected location on the dash to help prevent plugging in deep snow. Fits all rush and Pro-R sleds.
91
snowmobile engine
92
BMP Offset Timing Keys
Our timing keys are offset to advance timing by slightly rotating the flywheel in various degrees. Advance your timing for
more horsepower, typically its 1-2hp per degree on average. Premium gas required in most cases. 4-5 degree typically
require race fuel. Easy bolt on performance! Small Keys: Fits Carburated F6, F7, ZR800, ZR900, 440, 500, 600, 700 ZR’s,
ZRT 800, 900,1000 triples. Large Keys: Polaris & Arctic Cat EFI Models.
Part #
Offset
Size
Price
BMP-TK1
1.3 Degree
Small
$23.95
BMP-TK2
2.6 Degree
Small
$23.95
BMP-TK3
4 Degree
Small
$23.95
BMP-TK4
1.25 Degree
Large
$23.95
BMP-TK5
2.5 Degree
Large
$23.95
BMP-TK6
3.75 Degree
Large
$23.95
BMP-TK7
5 Degree
Large
$23.95
snowmobile engine
93
Cometic 2 Stroke Top End Gasket Kits
High quality top end gaskets sets made by Cometic meet or exceed the OEM specs.
We recommend using new gaskets any time you tear your top end apart. Ski-Doo
800 owners beware when taking your stock cylinder off. The stock gasket will
have a certain amount of holes in the front of it. These holes represent the gasket
thickness and need to be considered when purchasing new gaskets. 5 and 6 hole
gaskets would take the 0.6mm thickness kit, while 7 & 8 hole gaskets would take the
0.8mm thickness kit. Not sure which one you had/have? Go with the thicker 0.8mm
version. This version is most commonly found on the E-Tec 800 models. Not finding
the gasket kit you want? Log on our website to find even more!
Part #
Actual Product May Vary
Model
Parts Included
Price
CALL
2010-Up 800 HO
Inner & Outer Cylinder O-Rings, Base Gasket, Power Valve Gaskets, Exhaust Manifold To Cylinder Gaskets, 2 Reed Gaskets
$89.95
CM-1040
2003-06 F/M/Crossfire 600/700
Inner & Outer Cylinder O-Rings, Base Gasket, Power Valve Gaskets, Exhaust Manifold To Cylinder Gaskets, 2 Reed Gaskets
$89.95
CM-1042
2003-06 440 & 04-07 F5
Inner & Outer Cylinder O-Rings, Base Gasket, Power Valve Gaskets, Exhaust Manifold To Cylinder Gaskets, 2 Reed Gaskets
$89.95
CM-1035
ZR/ZL/Mountain Cat 800/900 Twin
Inner & Outer Cylinder O-Rings, Base Gasket, Power Valve Gaskets, Exhaust Manifold To Cylinder Gaskets, 2 Reeds Gaskets, Water Pump Gaskets, Head Bolt O-Rings
$101.95
CALL
2008-Up 800 CFI
Inner & Outer Cylinder O-Rings, Base Gasket, Power Valve Gaskets, Exhaust Manifold To Cylinder Gaskets
$89.95
CM-2066
2006-Up 600 HO Twin
Inner & Outer Cylinder O-Rings, Base Gasket, Power Valve Gaskets, Exhaust Manifold To Cylinder Gaskets
$89.95
CM-1052-6
2008-Up 800R & 800 E-Tec (0.6mm
Base Gasket, 6 Hole)
Inner & Outer Cylinder O-Rings, Base Gasket, Power Valve Gaskets, Exhaust Manifold To Cylinder Gaskets
$89.95
CM-1052-8
2008-Up 800R & 800 E-Tec (0.8mm
Base Gasket, 8 Hole)
Inner & Outer Cylinder O-Rings, Base Gasket, Power Valve Gaskets, Exhaust Manifold To Cylinder Gaskets
$89.95
CM-1044
2003-07 HO / SDI
Inner & Outer Cylinder O-Rings, Base Gasket, Power Valve Gaskets, Exhaust Manifold To Cylinder Gaskets
$89.95
CM-3030
2000-06 Rev/Summit 800 Twin
Inner & Outer Cylinder O-Rings, Base Gasket, Power Valve Gaskets, Exhaust Manifold To Cylinder Gaskets, Water Pump Gaskets
$89.95
Arctic Cat
BMP-PSR : BMP Ballistic Pull Start Rope - $23.95
Dont ever break another starter rope! This 9000 lb tensile strength synthetic rope will last for
years and pull over even high compression motors with ease. A proprietary synthetic material
makes this the strongest rope you can buy. High horsepower, high compression, or simply stock
motors will never have a problem with this new ballistic pull start rope. Eliminate the possibility
of being stranded with a broken pull cord. Comes gray in a 7’ length.
BD-20005 : BDX Oil Elimination Kit - $41.95
Polaris
Ski-Doo
An oil injection elimination you do not have to maintain! We use a lubricant injected bushing, this means no greasing, install and forget about it! We have yet to wear one out! Fits
05’ - UP 700cc - 1000cc Arctic Cats
BMP-OS : BMP Oil Sleeve - $23.95
Tired of leaking oil caps? The tops of the oil container easily warp which causes
the cap to leak. This billet sleeve with an o-ring makes the hole round and seal
tightly. Heat gun may be necessary for installation. Fits: Ski Doo XP, Rev, ZX, CK, F
and S chassis; Arctic Cat Crossfire, M-Series and Sno Pro Chassis; Polaris Edge,IQ,
RMK, SKS, Switchback, Rush, Indy, Fusion, Evolved and Aggressive Chassis
Oil Sleeve Installed
snowmobile engine
94
snowmobile engine
95
Wossner Replacement Pistons
Wossner is Germany’s finest aftermarket forged piston and rod manufacture which has over 25 years of experience in the
high performance racing industry. Wossner is part of the Wossner group which also includes FGM (Forging Group Monale)
our Italian forging house for which we supply parts for notable companies such as Fiat, Ducati, Triumph just to name a few
as well as Wossner USA our distribution facility in Huntington Beach California.
At Bikeman Performance, we have used many pistons from many manufacturers. Without a doubt these german made
pistons are the best we have ever dealt with. Exceptional quality, attention to detail, and a reasonable price. We trust
them with all of our performance motors, and so should you! Below you will find various pistons for many makes & model
snowmobiles. While we try to keep most the popular model pistons in stock, some pistons may ship direct from the Wossner
California warehouse. Don’t see your model? Give us a call and we can most likely help find you one! Oversize pistons are
also available for most models with iron lined cylinders. Most kits include 1 piston, rings, circlips & wristpin. Sold as each.
“The best quality and
performance we have ever
seen out of an aftermarket forged piston”
Part #
Description
Year
$ Price
WO-7005DA
Arctic Cat 550 Liquid ZL/EXT/Cougar/Prowler
1992-2003
119.95ea
WO-7006DA
Arctic Cat ZRT600
1996-2000
119.95ea
WO-7007DA
Arctic Cat ZR/ZL 600
1998-2000
129.95ea
WO-7008DA
Arctic Cat ZR/ZL/Mountiain Cat 600
2001-04
139.95ea
WO-7009DA
Arctic Cat F/M/CFR 700
2003-06
154.95ea
WO-7010DA
Arctic Cat ZR/ZL/Wildcat/Mountain Cat 700
1991-00
129.95ea
WO-7011DA
Arctic Cat ZR/ZL/Mountain Cat 800
2001-04
154.95ea
WO-7012DA
Arctic Cat ZRT 800
1995-2001
129.95ea
WO-7013DA
Arctic Cat Thundercat 1000
1998-02
129.95ea
WO-7014DA
Arctic Cat F/M/CFR 1000
2007-11
143.95ea
WO-7035DA
Arctic Cat Sno Pro 500
2010-UP
143.95ea
WO-7038DA
Arctic Cat F/M/CFR 800
2007-09
143.95ea
WO-7015DA
Polaris Fuji Motor 550 Fan
1999-05
143.95ea
WO-7016DA
Polaris 600 Big Block
1998-01
137.95ea
Part #
Description
Year
$ Price
WO-7017DA
Polaris 600 Switchback
2000-07
154.95ea
09-AC550BBP
Arctic Cat Sno Pro or F5 550cc Big Bore Piston (Wossner Piston)
All
$229.95ea
WO-7018DA
Polaris 700 Big Block
1998-05
179.95ea
09-AC800BBP-C
Arctic Cat 800cc Big Bore Piston for Sno Pro 600 (Wossner Piston)
2007-11
$229.95ea
WO-7031DA
Polaris Dragon/RMK 700
2007
174.95ea
09-AC800BBP-A
Arctic Cat Old Style F800cc Big Bore Piston for F/M/X-Fire 600/700 (Wossner Piston)
2003-06
$229.95ea
WO-7019DA
Polaris 800 Big Block
2001-05
149.95ea
09-AC800BBP-B
Arctic Cat Newer Style 800cc Big Bore Piston for F/M/X-Fire 600/700 (Stock Arctic Cat Piston)
2003-06
$179.95ea
WO-7020DA
Polaris 900 Fustion/RMK/Switchback
2005-06
139.95ea
09-AC900BBP
Arctic Cat 900cc Big Bore Piston for F/CFR/M/ZR 800 (Wossner Piston)
2010-Up
$229.95ea
WO-7044DA
Polaris 800 CFI
2008-Up
179.95ea
09-AC1200BBP
Arctic Cat 1200cc Big Bore Piston for F/CFR/M 1000
2007-11
$264.95ea
WO-7021DA
Ski-Doo Rev/Renegade/Summit/GSX/GTX 600 STD/HO/SDI/E-Tec (Dual Ring Piston)
2003-Up
189.95ea
09-SD880BBP
Ski-Doo 880cc Piston for XP800R (Wossner Piston)
2008-11
$229.95ea
WO-7022DA
Ski-Doo 793cc Engine - 800 STD/HO *Not 2007 Summit 800R* (Dual Ring Piston)
2000-07
184.95ea
09-SD880BBP
Sk-Doo 860cc Piston for E-Tec 800 (Wossner Piston)
2011-Up
$229.95ea
WO-7023DA
Ski-Doo 800R Carb / 800 E-Tec (Dual Ring Piston)
2008-Up
197.95ea
09-P660BBP
Polaris 660cc Big Bore Piston for 600 VES (Wossner Piston)
2002-Up
$179.95ea
WO-7028DA
Sk-Doo MXZ/Legend 500
2000-03
154.95ea
09-P670BBP
Polaris 670cc Big Bore Piston for IQ 600 Race Sled (Wossne Piston)
All
$229.95ea
WO-7046DA
Ski-Doo MXZ Fan
2003-08
154.95ea
09-P860BBP
Polaris 860cc Big Bore Piston for Pro-R 800 (with NO base spacer; stock height piston) (Wossner)
2011-Up
$229.95ea
WO-7047DA
Ski-Doo 99-04 MXZ 600, 500SS 04-09, 600 Carb 09-UP
Varies
174.95ea
09-P860BBP-B
Polaris 860cc Big Bore Piston for Pro-R 800 (with base spacer; taller piston) (Wossner Piston)
2011-Up
$229.95ea
WO-7049DA
Ski-Doo MXZ/Legend/Summit 700 Twin
01-04
179.95ea
09-P875BBP
Polaris 875cc Big Bore Piston for Pro-R 800 (with base spacer; taller piston) (Wossner Piston)
2013-Up
$229.95ea
WO-7050DA
Mach Z/Summit 1000
All
197.95
09-ET900
Engine Tech 900 Piston (Yep we made them for those left without pistons!) (Wossner Piston)
All
$229.95ea
BMP Big Bore Replacement Pistons
Looking to freshen up that powerful BMP big bore motor? We offer piston kits for all of our big bore motors. Most forged
pistons are custom made from Wossner pistons of Germany. Most kits include 1 piston, rings, circlips, and wristpin.
snowmobile efi controllers
96
Power Commander 5
The Power Commander V from DynoJet is the latest in EFI control technology, giving you full EFI tuning capability for your fuel
injected snowmobile. It allows a fuel map to be built with input points at 10 different throttle positions and in 250 RPM increments. This provides much more adjustability than other boxes on the market, allowing us to create fuel maps that optimize
performance and fuel economy for specific combinations. BMP’s fuel maps can be preprogrammed into the controller for true
plug and play capability. For the experienced tuner, the controller comes with a computer link cable and software for custom
mapping capabilities. No wiring modifications required (OEM style connectors are supplied) and no permanent changes are
made to your stock system. The Power Commander 5 also allows you to use the Auto Tune module to create a fine tuned custom map for your sled while riding! Combine this with the LCD screen to monitor air/fuel ratio’s and much more!
snowmobile efi controllers
DJ-AT-200 : Auto Tune for PCV - $335.95
Don’t have a dyno tuning center nearby? Are you more of a D.I.Y. (do
it yourself ) type? Are you constantly changing parts on your bike?
Once installed, the Auto Tune kit monitors the fuel mixture (by installing
the included Wide Band O2 sensor in the exhaust). It then sends this
information to the Power Commander V and automatically corrects it
while you ride. Each map that we offer has preset Air/Fuel ratio values
included that we find to be the best overall settings. This lets you simply
plug in the unit and let it do the work.
Why buy your PCV from BMP?
Custom tuned maps for our products easily available
we load one of our custom tuned maps for free
Online tutorol to help you use your PCV
Great customer support with PCV purchase
DJ-PC-LCD : Power Commander LCD Screen - $359.95
Power Commander LCD connects to any Power Commander via“quick disconnect” cable and is designed to remain on the machine and is weather
resistant. Displays all Power Commander data “real-time”. Allows storage
& swtiching between multiple maps. Data loggin capable (Requires SD
Memory Card, must be purchased seperately). “On Screen” map adjustments. User comfigurable screens. USB programmable & upgradable.
Active Matrix TFT LCD 240x320 16 bit color screen
maps available by visiting
bikemanperformance.com > downloads > power commander maps
DJ-SFM-DP : Arctic Cat Secondary Fuel Module - $299.95
More PC5 Controllers
Available Online
Part Number
Model
Year
Price
DJ-PC-11-007
Arctic Cat 500/600/700 EFI (Excludes Pantera)
2005-Up
$455.95
DJ-PC-11-007-PTI
Arctic Cat 500/600/700 EFI Turbo (Excludes Pantera)
2005-Up
$539.95
DJ-PC-11-004
Arctic Cat 800/1000 EFI
2007-Up
$455.95
DJ-PC-11-013
Arctic Cat 800/1000 EFI with Ignition Control
2007-Up
$539.95
DJ-PC-11-004-PTI
Arctic Cat 800/1000 EFI Turbo
2007-Up
$539.95
DJ-PC-11-009
Arctic Cat 1100 Turbo
2012-Up
$455.95
DJ-PC-19-004
Polaris CFI 2 Models
2011-Up
$455.95
DJ-PC-19-004-PTI
Polaris CFI 2 Models Turbo
2011-Up
$539.95
DJ-PC-19-007
Polaris CFI 4 Models
2008-10
$455.95
DJ-PC-910-411
Polaris 700 Twin EFI ***POWER COMMANDER 3***
2004
$429.95
DJ-PC-911-411
Polaris 700 Twin EFI ***POWER COMMANDER 3***
2005-08
$429.95
DJ-PC-25-002
Ski-Doo 4-TEC
2009-11
$455.95
DJ-PC-25-002-PTI
Ski-Doo 4-TEC
2009-11
$539.95
DJ-PC-25-015
Ski-Doo E-Tec 800 XP Chassis
2011-12
$539.95
DJ-PC-25-017
Ski-Doo E-Tec 800 XS/XM Chassis
2013-14
$579.95
DJ-PC-22-052
Phazer / Venture Lite FUEL & IGNITION
All
$479.95
DJ-PC-22-025
Nytro
All
$455.95
DJ-PC-22-025-PTI
Nytro (Turbo Control Box)
All
$539.95
DJ-PC-22-038
Apex
All
$455.95
DJ-PC-22-038-PTI
Apex (Turbo Control Box)
All
$539.95
Auxilary injector control box. If you are running the pcv with PTI option for turbo applications and you wan to run 4 injectors instead of two, you will need this trick little unit. To run
more than 8lbs of boost you will need more than the stock 2 injectors. This unit piggy backs
right into the turbo PTI power commander and allows you to run up to roughly 20lbs of
boost for example on the 800’s. 1000 & 1200 motors can get slightly over 20lbs of boost.
DJ-PCC : Power Commander Combo - $1114.95
That’s right, we’ve combined your favorite power commander products
for a great price! This deal includes the Power Commander 5 (not PTI
or IGN boxes), Auto Tune & LCD screen. This is the ultimate package
for fine tuning your sled! Literally as close as you can get to putting
your machine on the dyno, without actually doing it! We can also preset parameters and load a starting map if desired.
DJ-PC-MS : Power Commander Map Switch - $59.95
Connecting the optional Map Selection Switch allows the rider to switch between two different maps within the Power Commander. This allows riders to switch between a lean or rich map
depending on altitude or temperature. Comes with handlebar mount.
97
snowmobile turbo kits
Boondocker Control Boxes
Back in the day we used to do modifications to our machines and change carburetor jetting to dial in the fuel. When the
new fuel injected machines came out we knew those days were over and we had to figure out how to tune the fueling
before we could do any other modifications. So we developed the Control Box, this electronic modules plugs into the stock
fuel system and makes changes based on the settings selected on the module. By being able to precisely control the fueling
on any modern fuel injected machine we have opened the door to any form of modification that requires different fuel
tuning. The Control Box has the ability to both add and subtract fuel without the use of a laptop. Some Control Boxes are
equipped with 3D Tuning that allows users to control fuel based on rpms, boost and throttle position. Control Boxes are
available for turbo, nitrous and naturally aspirated applications.
Many other control boxes for snowmobiles,
ATV’s and UTV’s are available online at
BikemanPerformance.com
Part Number
Description
$ Price
BN-CBA-A004
Arctic Cat 2007-14 All Models (Fuel Only)
499.00
BN-CBA-A027
Arctic Cat 2007-14 All Models (Fuel + Nitrous)
499.00
BN-CBA-A026
Arctic Cat 2002-06 All Models (Fuel Only)
499.00
BN-CBA-005
Arctic Cat 2002-06 All Models (Fuel + Nitrous)
499.00
BN-CBA-B001
Skidoo SDI 2 injector (Fuel + Nitrous)
499.00
BN-CBA-B002
Skidoo SDI 4 injector (Fuel + Nitrous)
499.00
BN-CBA-P002
Polaris Dragon 700/800 4 Injector (Fuel + Nitrous)
499.00
BN-CBA-P009
Polaris Dragon 600 2 injector (Fuel + Nitrous)
499.00
BN-CBA-P013
Polaris Pro-R 800 2013-Up (Fuel Only)
499.00
BN-CBA-P016
Polaris Pro-R 800 2013-Up (Fuel + Nitrous)
499.00
BN-CBA-P010
Polaris Pro-R 800 2011-12 (Fuel + Nitrous)
499.00
BN-CBA-Y001
Yamaha Apex (Fuel + Nitrous)
499.00
BN-CBA-Y002
Yamaha Apex (Turbo + Fuel + Nitrous)
740.00
BN-CBA-Y003
Yamaha Nytro (Fuel + Nitrous)
499.00
BN-:CBA-Y004
Yamaha Nytro (Turbo + Fuel + Nitrous)
740.00
99
Push Turbo Systems
Push turbo kits are a true state of the art, high performance turbo charging system. They use only the best components to
create the most capable and forward thinking design possible. Available for a wide range of today’s latest models, they
set out to make installation easy. Precise mounting brackets, great fit and finish, and big horsepower are just a few things
you will notice with these kits! Descriptions for Yamaha kits are located on page 65. Descriptions are very detailed on these
kits, so please log on to bikemanperformance.com for more information.
STATE OF THE ART TURBO SYSTEMS
98
snowmobile efi controllers
Boondocker Arctic Cat Proclimb 800 Turbo Kit
The BoonDocker turbo kit for the Proclimb M800 comes with all the unique features that are standard on all BoonDocker
turbo kits. A Garret 2860 turbo fits in place of the stock muffler and is lubricated by a self-contained oil system with a
vented no-spill oil tank. Boost is fed to the throttle bodies through an extruded aluminum intercooler and a tubular torque
building air box. The machine is fueled using auxiliary fuel injectors controlled by the Control Box. The Control Box features
3D tuning that allows the user to tune the machine based on boost, rpm and throttle position. Turbo boost is adjustable at
the touch of a button using the Electronic Boost Controller, for this season the EBC is equipped with a TPS Smart feature that
matches boost to throttle position. By synchronizing boost to throttle position the EBC controls boost so there is always boost
when the throttle is opened and over-boost at part throttle is prevented. As with all BoonDocker turbo kits this kit comes
pre-assembled and with clutching components for simple installation.
Boondocker Polaris Pro RMK Turbo Kit
Following a successful first season working with turbochargers on the Polaris Pro-RMK BoonDocker have added several new
features for even better performance. Both intercooled and non-intercooled kits feature a new Torque Building airbox design that
features dual billet aluminum o-ring throttle body adaptors with dual auxiliary injectors.The BoonDocker Polaris Pro-RMK turbo
kits come with a deep snow tunnel exit exhaust, cold air intake, vented no-spill oil tank and BoonDockers advanced electronics
Model
Parts Included
$ Price
Proclimb 800 Stage 1
BN-PC800-S1
Garrett 2860, oil system, air box, no spill oil tank, clutching, turbo oil, 3D control box, auxilary injectors, waterproof
air intake filter,
5695
Proclimb 800 Stage 2
BN-PC800-S2
Garrett 2860, oil system, air box, no spill oil tank, clutching, turbo oil, 3D control box, auxilary injectors, waterproof
air intake filter, Intercooler, electronic boost controller, louvered vents
6980
Pro-RMK Stage 1
BN-RMK-S1
Garrett 2860, oil system, air box, throttle body adaptors, no spill oil tank, deep snow exhaust, clutching, turbo oil,
3D control box, auxilary injectors, waterproof air filter
5695
Pro-RMK Stage 2
BN-RMK-S2
Garrett 2860, oil system, air box, throttle body adaptors, no spill oil tank, deep snow exhaust, clutching, turbo oil,
3D control box, auxilary injectors, waterproof air filter, intercooler, electronic boost controller, louvered vents
6980
Model
Parts Included
91 Oct HP
$ Price
Yamaha Nytro (See page 65
for full description)
Boost Gauge, AEM o2 Gauge, Trail Friendly or Standard Muffler, Ceramic Coated Turbo,
Turbo Stand, Charge Tube, Air Box, Braided SS oil return line, and all other necessary parts
required for installation.
200hp
$4295
Yamaha Viper 2014 (See page
65 for full description)
liquid to air intercooler, ceramic coated exhaust, cold air intake, clutching, easy to install the
turbo system is pre assembled. trail friendly muffler. all other necessary, components.
200hp
$4995
Polaris RMK 2011-Up
Turbo Vi-Pec ECU, Intake Manifold, Throttle Body, Injection Cooling System, Charge Tubes,
Polished Stainless Exhaust, Quiet Stainless Muffler, Tial 28-73 Turbo With HTA Billet Wheel,
V-Band Wastegate, Cold Air Intake, Frog Skinz Vent System, and all other necessary parts
required for installation.
200hp
$8995
Arctic Cat M800 2012-Up
Turbo Vi-Pec ECU, Intake Manifold, Throttle Body, Injection Cooling System, Charge Tubes,
Polished Stainless Exhaust, Quiet Stainless Muffler, Tial 28-73 Turbo With HTA Billet Wheel,
V-Band Wastegate, Cold Air Intake, Frog Skinz Vent System, and all other necessary parts
required for installation.
215hp
$8995
Arctic Cat ZR/XF 7000 C-Tec
liquid to air intercooler, ceramic coated exhaust, cold air intake, clutching, easy to install the
turbo system is pre assembled. trail friendly muffler. all other necessary, components.
200hp
$4995
snowmobile nitrous kits
100
koso gauges
SPI Nitrous Kits
These kits includes the patented nitrous injector nozzle and the patented piggy back solenoid. The technology in the
patented nitrous nozzle provides constant and consistent nitrous flow no matter what bottle pressure you are running.The
Arctic Cat EFI kit for the M and Crossfire is a simple yet effective bolt on. The EFI nitrous kits DO NOT REQUIRE A FUEL
PROGRAMMER TO RUN. Kit comes complete with all necessary mounting brackets, 30hp nitrous nozzle, waterproof button, patented solenoid, and detailed instructions. This is the safest and easiest kit to install with the most reliable nitrous
technology available today. Bottle’s Sold Separately.
Part Number
Model
Price
SP-164-102
Yamaha Phazer
$779.95
SP-164-101
Yamaha Nitro
$779.95
SP-164-100
Yamaha Attack/Apex
$809.95
162-104
Polaris Pro-R 800 2011-Up
$779.95
SP-162-101
Polaris Dragon 800
$809.95
SP-161-108
AC ZR/F/XF/M 800 2012-Up
$779.95
SP-161-105
AC M/CFR 1000
$809.95
SP-161-103
AC M/CFR 600/700
$779.95
SP-161-104
AC M/CFR 800
$779.95
SP-161-100
AC F7
$779.95
SP-163-102
Ski-Doo Rev 800 & 800HO
$779.95
SP-163-103
Ski-Doo 1000 SDI
$779.95
SP-163-105
Ski-Doo XP 600 SDI
$779.95
SP-163-107
Ski-Doo XP 800R Electric Start
$779.95
SP-163-108
Ski-Doo XP 800R No Electric Start
$779.95
SP-163-109
Ski-Doo 4-TEC
$779.95
163-110
Ski-Doo E-Tec 800
$779.95
SP-25B
2.5 Pound Bottle With Siphon Tube
$197.95
SP-160-108
1.25 Pound Bottle
$143.95
SP-160-107
1.25 Pound Bottle With Siphon Tube
$143.95
Nitrous Kits
Bottles
Nitrous kits available for other makes and models. Please
log on to BikemanPerformance.com for more information.
KO-BA029001 : X-2 Boost/AFR/Temp Gauge - $599.95
This multi-function unit is a great tool for all horsepower enthusiasts that are upgrading there engine wit ha turbocharger or supercharger. Following many requests we
came up with a unit that combines boost, air fuel ratio and temperature function that
can be installed on the cooling system or the intercooler. This gauge is made to resist
cold temperature, water, or dust. It can easily adapt to many engines with a turbo
or supercharger. The X-2 instrument will give you precious information to help you
maximize horsepower and save it from potential damages. For UVT’s and machines
that require longer AFR wires we now offer an exclusive gauge just for you!
KO-BA004068 : Koso Wideband AFR Gauge - $399.95
This nice back lit Wideband Air/Fuel Ratio Gauge will give you precise information on your
engine. This will help you determine if your engine is running rich or lean. Very good engine
tuning tool. Specifications: 12V DC Voltage Only, Display Range 10.0-24.0 A/F, Over Lean
Setting 14.8-24.0 A/F, Over Rich Setting 14.6-10.0 A/F, Screen Update’s 2 x Second, Water
Proof, Instrument Weighs 3 oz’s, Instrument dimensions 4.0”L x 1.75”H x 1.0”W. Includes: Koso
Instrument, Bosch Wide-Band O2 sensor, Weld Bung & Plug, Wiring Harness, Universal Mounting Bracket, Instruction Manual. Be sure to get an adapter fitting for 2-strokes!
KO-BA004065 : Single EGT Standard Probe - $259.95
KO-BA005065X : Single EGT Fast Probe - $274.95
This nice back lit Exhaust temperature gauge will give you precious information about your
engine. It will allow you to tune your engine more precisely. It’s warning could even save your
engine from potential damage! Available with standard response, or fast response probe.
KO-BA006B61 : Koso Dual EGT Gauge Standard Probes - $379.95
KO-BA006B61X : Koso Dual EGT Gauge Fast Probes - $439.95
This trick little dual EGT gauge mounts just about anywhere and works great. This
gauge features backlighting, overlimit warning, and peak temp. You can also have it
read in either Farenheit or Celsius for you Canadians! This complete kit includes gauge,
two heavy duty probes, mounting plate, and instructions. Works on all two stoke twin
cylinder sleds. Some sleds may require an AC/DC adaptor. Available with regular
response or fast response probes.
KO-BA006B00X : Koso EGT/RPM/Water Temp Gauge - $529.95
BOONDOCKER NITROUS KITS AVAILABLE
Continuing on with the evolution of our dual EGT gauge, Koso is proud to offer the
dual EGT with RPM and Water temperature. This gauge allows you to tune the engine
more precisely and prevent engine damage. The settable warning and maximun recall
functions for both EGT’s, RPM and water temperature are easy to use and show you
vital engine information. The color change and backlighted screen makes it very easy
to see even at night.This cool instrument can save your engine from expensive repairs!
101
koso gauges
102
black diamond extreme products
BD-20001 : Arctic Cat Rear 2 Wheel Kit - $29.95
BD-20001-POL : Polaris Rear 2 Wheel Kit - $41.95
BD-20001-XP : Ski-Doo XP Rear 2 Wheel Kit - $41.95
KO-BA003035 : Koso Mini LCD Thermometer - $95.95
This mini Back lit LCD water temp gauge will give critical information on the engine
temperature. Its small size makes it easy to install. This unit is about the smallest and
lightest temperature gauge on the market. Most applications will require an additional water temp sensor adaptor sold seperatly.
Two wheel kits that use stock wheels and shed weight!
BD-20003 : Inner Idler Wheel Kit 05-06 M & X-Fire - $95.95
BD-20002 : Inner Idler Wheel Kit 07-Up M & X-Fire - $95.95
KO-BA029000 : Koso X1 Boost Gauge - $234.95
Want to take your front stock idlers off without abnormal hi-fax wearing? This is
the kit you need. This remedites the track hitting the shaft on 05’and 06’ models
and great addition for 2-wheel kits for the 05’ - 11’.
Today many horsepower enthusiast are upgrading their engine with Turbo or Supercharger. For this reason we came up with this basic boost gauge with warning and
peak functions. Made to resist cold temperature water or dust this gauge can be
adapted to any engines with turbo or supercharger. The changeable scale from 15
to 30 psi the warning and peak recall function makes it a great tool.
BD-20014 : Anti Slop Steering Post Support - $69.95
Eliminate the steering post slop from your stock support! The new BDX Anti-Slop
Support will eliminate the slop from the stock support and lessen the chance of
your steering post breaking! 05’ - UP M-Series and X-Fire.
Koso Miscellaneous Parts
Part Number
Description
$ Price
KO-BL00010
AC/DC Converter
47.95
Picture
KO-BI520099
Weld On EGT Fitting
26.95ea
KO-28-CKTYPE9
Standard Type EGT Sensor (40-60mm Clamp Included)
95.95ea
C
KO-28-CKTYPEX
FAST RESPONSE EGT SENSOR (CLAMP INCLUDED 40-60MM)
119.95ea
C
KO-28-BOSCH
WIDE BAND BOSCH OXYGEN SENSOR - Fits ON : BA004068
119.95
E
A
B
KO-BG001855
Koso 2-Stroke AFR Sensor Adaptor
47.95
F
KO-BG001800
AFR Sensor Bung
11.95
G
KO-BG001801
AFR Sensor Bung Cap
11.95
KO-BI520001
EGT Clamp 40-60mm
12.95ea
J
KO-BI520002
EGT Clamp 60-80mm
12.95ea
J
KO-BG014B01
Water Temp Sensor Adaptor 14mm (includes hose clamps)
3495
L
Water Temp Sensor Adaptor 16mm (includes hose clamps)
34.95
L
KO-BG018B01
Water Temp Sensor Adaptor 18mm (includes hose clamps)
34.95
L
KO-BG022B01
Water Temp Sensor Adaptor 22mm (includes hose clamps)
39.95
L
K0-BG026B01
Water Temp Sensor Adaptor 26mm (includes hose clamps)
44.95
H
J
Black Diamond has developed an Anti-Stab Roller Kit for the M-Series sleds. It is designed to help prevent the rail tips from stabbing through the 3”pitch track windows.
It also eliminates the vibration produced when the rail tips click on the windows. This
vibration is felt in the foot-wells while operating in loose snow conditions. The AntiStab Roller Kit is a must for the rider who runs with loose track.
H
KO-BG016B01
G
BD-50017 : M Series Anti Stab Kit (05-06) - $83.95
BD-50018 : M Series Anti Stab Kit (07-11) - $83.95
BD-50019 : Proclimb Anti Stab Kit (2012-Up) - $83.95
BD-20030 : M/X-Fire Headlight Elimination (Non-Vented) - $54.95
You have been asking! Well here they are! Black Diamond Xtreme’s Headlight Elimination Kit! Virtually indestructable these headlight replacements have an OEM fit! Save
weight! Fits 05’ - UP M-Series and X-Fire. Comes with everything to install!
L
L
BD-20030-V : M/X-Fire Headlight Elimination (Vented) - $83.95
A
B
You have been asking! Well here they are! Black Diamond Xtreme’s Vented Headlight
Elimination Kit! Virtually indestructable these headlight replacements have an OEM fit!
Save weight! Comes with everything to install including extra adhesive screens with our
exclusive hydrophobic screen! A $20.00 value! Fits 05’ - UP M-Series and X-fire.
C
E
F
Need a bung welded in your manifold, pipe or muffler? We can help! We can install o2 bungs or EGT bungs in any of our products before they get painted or
coated. Installation + EGT bung $25 each. Installation + o2 bung $20 each.
BD-EYEPOD : M/X-Fire Eyepod Gauge Pod - $119.95
This gauge pod will improves your ability to see the stock gauge plus has two optional
customer cut 2 1/16 gauges holes! Available space to mount Koso gauges. Also has a compartment for storing your googles or gloves. The vents on the front and side will proved air
flow to dry your gloves or googles in no time! Fits 2008-11 M/X-Fire Models
103
104
black diamond extreme products
Black Diamond Lite Weight Trackshafts & Replacement Drivers
ZR, M/X-Fire model trackshafts use a PATENT PENDING slip-washer with a shorter higher grade bolt to replace the heavier, lower grade OEM bolt. These models also drop 2lbs of rotating mass! Procross/Proclimb models drop 1lb of rotating
mass! Any year sled with a diamond drive lite will require part number BD-50040.
black diamond extreme products
F/M/XF/ZR 2012-14
800 Models
Use 2007-11 trackshaft nut & socket for all year diamond drive sleds as an update. Use a punch to
remove 05-06 nuts, then use updated socket and nut for installation
Part Number
Build Your Own
Cat Pro Lite!
420 pounds
almost 200hp
M/X-Fire Light Weight Performance Parts
Description
Lbs Lost
Price
BD-50042
Diamond Drive ZR Models
2lbs
$143.95
BD-50040
M/X-Fire (All Years with Diamond Drive Lite)
2lbs
BD-62961
M/X-Fire 800/1000 2007-11
2lbs
BD-50032
8 Tooth Extrovert Driver 3” Pitch
0
$71.95ea
BD-50030
9 Tooth Driver 2.52” Pitch
0
BD-50031
10 Tooth Driver 2.52” Pitch
0
105
Choose all the products below
for the complete package, or
you can add a few parts at a
time. Drop over 60 pounds off
your already light machine!
Part Number
Description
Weight Loss Price
BD-20060
Xtreme BDX 2012-14 40" M/XF/Z1 Spindle/Upper Arm Kit
5lbs
$479.95
BD-20061
Xtreme BDX 2012-14 38" M/XF/Z1 Spindle/Upper Arm Kit
5lbs
$479.95
$143.95
BD-20062
Xtreme BDX 2012-14 Chrome Moly Rear Suspension Set
8lbs
$499.95
$143.95
BD-20066
BDX Air Intake with Delete (see page 91 for more details)
12lbs
$479.95
BD-20068-3
Lightweight Seat with Logo
3.5lbs
$599.95
BD-20070-C
Fuel Tank with 2.5gal Extra Capacity - Clear
5.5lbs
$419.95
$35.95ea
BD-20070-B
Fuel Tank with 2.5gal Extra Capacity - Black
5.5lbs
$419.95
$35.95ea
Page 85
Pro-Lite Front Bumper (See page 85 for color options)
0lbs
$109.95
BD-20069
Lightweight Chain Case Cover
5lbs
$239.95
Lightweight Trackshafts
Replacement Drivers
Trackshafts w/ Drivers Installed
BD-50040-10
Pro-Lite Series 05-06 M/CF Trackshaft w/10 Tooth Drivers Installed
2lbs
$239.95
BD-51002
Lightweight Brake Rotor
1.5lbs
$109.95
BD-50040-8
Pro-Lite Series 05-06 M/CF Trackshaft w/8 Tooth Drivers Installed
2lbs
$275.95
Page 85
Pro Lite Running Boards (See Page 85 for color options)
2lb
$479.95
BD-50040-9
Pro-Lite Series 05-06 M/CF Trackshaft w/9 Tooth Drivers Installed
2lbs
$239.95
BD-20008
Light Weight Recoil Drive
0.5lbs
$59.95
BD-50042-10
Pro-Lite Series ZR Trackshaft w/10 Tooth Drivers Installed
2lbs
$239.95
BD-62442
F/M/XF/ZR 800/1100/1100 Turbo 2012-Up
1lb
$143.95
BD-50042-8
Pro-Lite Series ZR Trackshaft w/8 Tooth Drivers Installed
2lbs
$275.95
Page 19
Stage 2 Torsion Clutch Kit - See Page 19
0lbs
$479.95
BD-50042-9
Pro-Lite Series ZR Trackshaft w/9 Tooth Drivers Installed
2lbs
$239.95
Page 25
BMP Complete 900 Big Bore Kit - See Page 25
22lbs
$5275.00
BD-62961-8
Pro-Lite Series 07-11 M/CF Trackshaft w/8 Tooth Drivers Installed
2lbs
$275.95
BD-62961-10
Pro-Lite Series 07-11 M/CF Trackshaft w/10 Tooth Drivers Installed
2lbs
$239.95
BD-62442-8
Pro-Lite Series 2012-13 ProClimb/XF/Z1 Series Track Shaft w/8 Drivers
1lb
$275.95
BD-62442-10
Pro-Lite Series 2012-13 ProClimb/XF/Z1 Series Track Shaft w/10 Drivers
1lb
$239.95
BD-50046
Trackshaft nut Socket 07-11
0
$35.95
BD-50045
Trackshaft Nut 07-11
0
$7.95
BD-20008-TB
M/X-Fire 800 2007-11 Models with Titanium Bolts
1/2lb
$69.95
BD-20010-TB
M/X-Fire 1000 2007-11 Models with Titanium Bolts
1/2lb
$69.95
BD-51000
M/X-Fire Lite Weight Black Ceramic Brake Rotor ***MUST USE CERAMIC PADS***
1.8lbs
$299.95
BD-51001
M/X-Fire Black Ceramic Brake Pads
0
$59.95
BD-20019
M Series 2007-11 Chrome Moly Nickel Plated Skid Arms
5lbs
$779.95
BD-20018-F
M Series 2007-11 Chrome Moly Nickel Plated A-Arms 42” Wide (Stock Width)
2lbs
$515.95
BD-20017-F
M Series 2007-11 Chrome Moly Nickel Plated A-Arms 40” Wide (Narrower)
2lbs
$479.95
BD-20018
M Series 2007-11 Chrome Moly Nickel Plated A-Arms + Skid Arms 42” Wide (Stock Width)
8lbs
$1199.95
BD-20017
M Series 2007-11 Chrome Moly Nickel Plated A-Arms + Skid Arms 40” Wide (Narrower)
8lbs
$1234.95
Trackshaft Nuts & Sockets
Lightweight Recoil Drive
Lightweight Braking
Light Weight Skid & A-Arms
106
black diamond extreme products
High quality, helpful tools for your Arctic Cat sled. For more information on the
following products please log on to bikemanperformance.com
As used on the Pro-Lite sleds! This trick looking chaincase cover
sheds over 5lbs off your machine! A must have if your trying
to make your already light sled even lighter! See preous page
for part number and pricing.
New for 07’ - UP M’s and Crossfire is our Diamond Lite Drive system
that takes off a true11 lbs (07’-08’) 4lbs (09’) of unwanted weight.
This system completely replaces your heavy stock reverse case and
comes with our new one piece light weight forged transfer and input
gears. Also we now give you our case with our exclusive oil dipstick
so you can now check your oil level and see your oil condition immediately. Our V-cast process gives our case billet strength. These
cases have been tested up to 350 HP. We have also increased the
oil capacity by 25% to give you more oil protection. There are no
modifications to the chassis at all, it is a direct bolt in conversion. Will
require our Lightweight trackshaft (P/N 50040). Also available with
Hi-Torq gears ; please call.
107
Black Diamond Extreme Tools
2012-Up Arctic Cat Chaincase Cover
Diamond Drive Lite - $83.95
snowmobile tools
Part Number
Gears
BD-85357
63/57
BD-85565
55/65
BD-85763
57/63
BD-85961
59/61
BD-86159
61/59
BD-86357
63/57
BD-86555
65/55
BD-86753
67/53
Part Number
Description
Picture
Price
BD-50033
Arctic Cat 3 Finger Spring Tool - Works well with BMP torsion kits on 2005-2014 models
A
$23.95
BD-50021
Arctic Cat TSS Clutch Tool - Adjustable Spring Rate Cam
B
$35.95
BD-50051
Arctic Cat TSS Clutch Tool - Fixed Spring Rate Cam
B
$35.95
BD-50051-09
Arctic Cat 2009 Belt Removal Tool
C
$35.95
BD-50035
Arctic Cat Diamond Drive Deflection Adjuster - Left Hand
D
$23.95
BD-50034
Arctic CatDiamond Drive Deflection Adjuster - Right Hand
D
$23.95
C
A
D
B
DIAMOND DRIVE SHOT?
TRY THIS ONE!!!
Arctic Cat Diamond Drive Maintenance Products
High Quality products to service your diamond drive and keep it in good working order.
Part Number
Description
Price
BD-50058
Diamond Drive Bearing Kit 2007-Up Reverse
$83.95
BD-50027
Diamond Drive Bearing Kit 2007-Up
$83.95
BD-50026
Diamond Drive Seal Kit 2004
$26.95
BD-50025
Diamond Drive Seal Kit 2005
$26.95
BD-50041
Diamond Drive Seal Kit 2006
$26.95
BD-50048
Diamond Drive Seal Kit 2007
$26.95
BD-50028
High Performance 12oz Oil Change Kit 2007-2008 Reverse Case
$15.95
BD-50028
High Performance 15oz Oil Change Kit 2009-2011 Reverse Case
$17.95
BD-50024-WO
High Performance 3oz Oil Change Kit Without Silicone
$11.95
BD-50052
BDX Bearing/Seal Install Tool
$35.95
BD-50036 : TSS Bench Tool : $239.95
The TSS Bench Tool is the most versatile secondary clutch disassembly tool in the industry. The TSS Bench Tool works with the older Arctic Cat roller clutch and the new
Diamond Drive secondary clutch. It also works with the older Polaris /Team keyway
clutch and the new splined Polaris/Team secondary clutch. This Tool is ideal for
cross brand dealers or snowmobile clubs. The large base also allows for use on any
flat surface. It can also be mounted to the bench top or secured in a bench vise.
The TSS Bench Tool can be used to inspect the full shift range for binding problems.
The TSS Bench Tool with it’s billet aluminum base has storage locations for bolts and
hardware. The center post is machined and hardened for years of daily service.
The center post can be changed for seasonal use. Additional center posts for ATV
applications will be available soon.
BD-50073 : Track Porting Tool - $35.95
Tired of picking track holes from your hole saw and then trying to burn the
frays? Here is the tool for you, the BDX Track Porting Tool! This quality one
piece tool ports tracks with ease...give it a try! 1.25 inch.
Stud Sharpening Tool
Keep your studs sharp with this handy tool that
uses index able carbide inserts to shrpen steel
studs. Available in 30 degree, 45 degree, and
60 degree angles
Part Number
Description
Price
SB-2206-30
SHARPENING TOOL 30 DEGREE
$99899
SB-2206-45
SHARPENING TOOL 45 DEGREE
$98.99
SB-2206-60
SHARPENING TOOL 60 DEGREE
$98.99
108
snowmobile tools
BMP-ACFP : Universal Flywheel Puller - $84.95
We made this heavy duty flywheel puller specifically for the Arctic Cat flywheels. We then slotted
it to work with most Ski-Doo and Polaris flywheels. This is a must for installing offset timing keys or
rebuilding your bottom end. Made out of 5/8” Thick steel and includes grade 10 bolts for pulling
even the toughest flywheels. Comes with Bolt for Arctic Cat only.
BMP-CCT : AC or Pol Drive/Driven Clutch Compression Tool - $59.95
These clutch press tools have been widely accepted as the most efficient clutch compression
tools available. This revolutionary drive and driven clutch servicing tool is designed specifically for compression and holding springs for ease of assembly and dissasembly. These
tools are specified in many factory repair manuals as required specialty tools for clutch
compression. Wrestling with the clutch or need for a second person to help is now history.
Made compact, the tool can be used for field testing or production clutch repair on the
shop bench. High quality metal construction with powder coated finish and UHMW plastic
wear patches and fingers provide a quality, functional tool that is extremely durable.
SLP-20-202 : SLP Drive Clutch Holding Tool - $44.95
This premium tool offers the proper method to hold the drive clutch from rotating while
removing or torquing the clutch center bolt. Unlike other clutch holding tools that are
laser cut, this tool will not hardmark or damage the clutch, making it a far more superior tool. It also features a cushion grip for comfort. This tool is a must for quick and
easy clutch removal. Fits Most Arctic Cat, Polaris, & Yamaha Models.
ST-106HRT : Rev XP QRS Helix Tool - $85.00
Comes with four hex-head screws to replace the stock torx screws. This will
allow replacement of your helix without removing the jackshaft from the
chaincase. Works on 2008-09 models only.
snowmobile tools
109
For more description on tools found below visit BikemanPerformance.com
BMP Misc Tools
Below you will find various tools we have found helpful for installing our products. Always refer to your service manual for
proper procedures and torque specifications when removing or installing products.
Part Number
Description
Picture
Price
ST-107EST
Exhaust Spring Tool
A
$24.00
BMP-GS
Gram Scale
B
$30.00
MB-10207
Primary Clutch Puller Arctic Cat 1996-2009 Models
C
$39.95
MB-10062
Primary Clutch Puller 07-09 1000cc, 2010-UP 800cc
C
$39.95
MB-10985
Primary Clutch Puller Polaris 2000 & Newer
C
$39.95
MB-10064
Primary Clutch Puller Ski-Doo TRA 1998-UP (Fits All E-Tec Models)
C
$39.95
SLP-20-146
Arctic Cat Spider Locking Nut Removal Tool
D
$59.95
SLP-20-206
Arctic Cat Spider Locking Nut Removal Tool
D
$59.95
SLP-20-198
Arctic Cat 4 Arm Clutch Spider Removal Tool
E
$59.95
SLP-20-175
Arctic Cat 6 & 9 Tower Clutch Spider Removal Tool
E
$59.95
SLP-20-192
SLP Clutch Holding Fixture 6 & 9 Tower Except Below Description
F
$95.95
SLP-20-197
SLP Clutch Holding Fixture F8, M8, F1000, M1000
F
$95.95
TP-930001
Secondary Compression Tool Team Rapid Reaction
G
$95.95
TP-930995
Secondary Compression Tool Diamond Drive
G
$95.95
SLP-20-164
Clutch Alignment Tool Pre Diamond Drive Arctic Cat
H
$39.95
SLP-20-184
Clutch Alignment Tool Diamond Drive Arctic Cat
H
$39.95
SLP-20-150
Clutch Alignment Tool Polaris Button Clutch
H
$39.95
SLP-20-191
Clutch Alignment Tool Polaris TSS-98 Clutch
H
$39.95
SLP-20-188
Clutch Alignment Tool Polaris TSS-04 or Tied Clutch
H
$39.95
05-SC-AC-1
Arctic Cat Sheave Clamp Tool (Fits all Arctic Cat Primary Clutches)
I
$11.95
05-SC-POL-1
Polaris Sheave Clamp Tool (Fits all Polaris Primary Clutches)
I
$11.95
B
ST-97XPBA10 : 2010-UP Rev XP QRS Secondary Belt Adjuster - $72.00
ST-97XPBA : 2008-09 Rev XP QRS Secondary Belt Adjuster - $93.00
Uses stock spanner in the tool kit for adjustment and is locked into position with a supplied
allen wrench. This unit stays in a fixed position and will not float back and forth. It also has a
plastic insert that contacts the helix surface. 2010 model pictured.
D
C
A
TP-930207 : TRA Button Retainers - $23.95
Must have for TRA clutch owners! These button retainers hold the buttons in
place while changing the weights or springs. Simply slide the place over the
buttons while dissasembling and reassembly will be a breeze! Set of 3.
SPI-151-106 : QRS Removal tool - $71.95
This reversible ratcheting wrench is used to remove and install the helix.This single-end, flat
wrench is 9-3/4” long with a removable/replaceable shortened T-40 torx bit. Low profile
design allows for easy access to the helix bolts between the frame and the clutch. Vinyl grip
provides a comfortable ergonomic grip and prevents the wrench from scratching or marring
your machine. Retaining ring allows for the bit to be removed and replaced when damaged.
E
F
H
G
I
110
atv & utv performance exhausts
BMP Full Velocity ATV/UTV Exhaust Systems
Our exhaust systems have been known to put down the most horsepower and torque in the industry. These pipes are engineered on the dyno to give you the most power possible with a great growl, yet not obnoxiously loud. Most exhaust systems
are available in standard black, ceramic chrome, or ceramic black finish. We recommend a ceramic coating because it
holds the heat hin the pipe, acting as a heat shield. This is very important with UTV’s especially as they get so hot under the
bed. Optional quiet cores, spark arrestors, and gaskets are available for most models. The RZR 900 models have an optional quiet cap for one muffler outlet and allow the use of one, or two factory spark arrestors. This allows you to go from
beast to stealth mode in seconds!
RZR 800
RZR 900 Full System
Double Barrel Style
atv & utv performance exhausts
111
Slip-On Exhausts
Part Number
Model
Year
HP
Finish
Price
08-RZR-SO
800 RZR, RZR S & RZR 4
All
2-3
Black Painted
$299.95
08-RZR-SO-C
800 RZR, RZR S & RZR 4
All
2-3
Ceramic Chrome
$359.95
08-RNGR800-SO
Ranger 800
All
2-3
Black Painted
$29.95
08-RNGR800-SO-C
Ranger 800
All
2-3
Ceramic Chrome
$359.95
08-SM850A-SO
Sportsman 850
2009
4-5
Black Painted
$2499.95
08-SM850A-SO-C
Sportsman 850
2009
4-5
Ceramic Chrome
$359.95
08-SM850B-SO
Sportsman 850
2010-UP
4-5
Black Painted
$299.95
08-SM850B-SO-C
Sportsman 850
2010-UP
4-5
Ceramic Chrome
$359.95
08-RZRXPDB-SO-C
RZR XP 900 (Double Barrel)
2011-UP
5-7
Ceramic Chrome
$419.95
08-RZRXPHR-SO-C
RZR XP 900 (Hot Rod)
2011-UP
5-7
Ceramic Chrome
$419.95
08-RZRXPDB-SO-BC
RZR XP 900 (Double Barrel)
2011-UP
5-7
Ceramic Black
$419.95
08-RZRXPHR-SO-BC
RZR XP 900 (Hot Rod)
2011-UP
5-7
Ceramic Black
$419.95
09-RNGR900-SO-C
Ranger 900
2011-Up
4-5
Ceramic Chrome
$599.95
09-RNGR900-SO-BC
Ranger 900
2011-Up
4-5
Ceramic Black
$599.95
08-RZR1000-SO-C
RZR 1000
2014
5-7
Ceramic Chrome
$419.95
08-RZR1000-SO-BC
RZR 1000
2014
5-7
Ceramic Black
$419.95
08-WCSO2-1-C
Wildcat 1000
2012-Up
3-4
Ceramic Chrome
$419.95
08-WCSO2-1-BC
Wildcat 1000
2012-Up
3-4
Ceramic Black
$419.95
08-SCM850-SO-C
Scrambler 850
2014
3-4
Ceramic Chrome
$359.95
08-SCM850-SO-BC
Scrambler 850
2014
3-4
Ceramic Black
$359.95
RZR 800
Wildcat
Ranger 700 / 800
Full Exhaust Systems
RZR XP Hot Rod
Part Number
Model
Year
HP
Finish
Price
08-RNGR700A
Ranger 700
2006-2008
5-6
Black Painted
$659.95
$719.95
08-RNGR700A-C
Ranger 700
2006-2008
5-6
Ceramic Chrome
08-RNGR700B
Ranger 700
2009
5-6
Black Painted
$659.95
08-RNGR700B-C
Ranger 700
2009
5-6
Ceramic Chrome
$719.95
08-SM800
Sportsman 800
All
6-8
Black Painted
$659.95
08-SM800-C
Sportsman 800
All
6-8
Ceramic Chrome
$719.95
08-RNGR800
Ranger 800
2010-UP
6-7
Black Painted
$659.95
08-RNGR800-C
Ranger 800
2010-UP
6-7
Ceramic Chrome
$719.95
08-RZR
800 RZR, RZR S & RZR 4
2008-UP
6-7
Black Painted
$659.95
08-RZR-C
800 RZR, RZR S & RZR 4
2008-UP
6-7
Ceramic Chrome
$719.95
08-RZRXPDB
RZR XP 900 (Double Barrel)
2011-UP
10-11
Ceramic Chrome
$809.95
08-RZRXPDB
RZR XP 900 (Double Barrel)
2011-UP
10-11
Ceramic Black
$809.95
08-RZRXPHR
RZR XP 900 (Hot Rod)
2011-UP
10-11
Ceramic Chrome
$809.95
08-RZRXPHR
RZR XP 900 (Hot Rod)
2011-UP
10-11
Ceramic Black
$809.95
08-RZR1000-C
RZR XP 1000
2014
11-12
Ceramic Chrome
$809.95
08-RZR1000-BC
RZR XP 1000
2014
11-12
Ceramic Black
$809.95
Ranger 900
Performance Head Pipes
Header pipes that will work with the stock muffler, our muffler, or any other slip-on exhaust. Easy bolt-on performance!
These headers come ceramic coated to hold the heat inside the pipe, which is very important on UTV’s!
Part Number
Model
Year
HP
Finish
Price
08-XP900H-1-C
RZR XP 900 Header Only
2011-UP
5-6
Ceramic Chrome
$419.95
08-XP900H-1-BC
RZR XP 900 Header Only
2011-UP
5-6
Ceramic Black
$419.95
08-XP1000H-1-C
RZR XP 1000 Header Only
2014
5-6
Ceramic Chrome
$419.95
08-XP1000H-1-BC
RZR XP 1000 Header Only
2014
5-6
Ceramic Black
$419.95
atv & utv clutching
112
atv & utv clutching
BMP Stage 2 UTV/ATV Clutch Kits
Leave your clutching to the experts! We have extensively tested all f our setups to make sure you gain the most performance possible. Most kits come with adjustable weights which are very important for a few reasons. Adjustable weights allow you to precisely fine tune your machine and compensate for altitude or other modifications you do down the road. Not
only that but the superior ramp angle on these custom weights gives your machine the extra kick in the pants to leave the
others in the dust! Many of our include a Team TAS-03 roller secondary clutch, models that do not include this clutch have it
on the machine already. The TAS-03 clutch is a much better clutch than the cheap one Polaris decided to put on many models. It allows quicker, smoother, and more consistant shifts. It also allows us to change out the helix and spring which is critical
for getting power to the wheels. Leave your clutching to BMP - other kits just don’t even come close! Please list all modifications including tires size and altitude when ordering. If you don’t see your model listed please call or go online.
UTV & ATV
Clutching
Experts!
113
BMP Goldstar Magnetic Adjustable Clutch Weights
Our Goldstar adjustable clutch weights are taking over! We developed a weight that is easy to use and easy to tune. This
weight kit allows for easy set up because magnets are used instead of fasteners. No thread lock needed, just a quick snap
in the recessed hole and your done! We have developed what we believe is a far superior ramp profile giving you the best
performance possible for your application. Many weights come bare and will rust over time. These weights all come zinc
plated making them look nicer and last longer. Choose the right weights for your make and model below.
Part Number
Application
Gram Range
Price
07-GSW-5678
RZR/Ranger/Sportsman 700/800/850
56-78
$275.95
07-GSW-7294
RZR/Ranger/Sportsman 700/800/850
72-94
$275.95
07-GSW-5572
RZR XP 900/1000 & Ranger 900
56-78
$275.95
07-GSW-7289
RZR XP 900/1000 & Ranger 900
72-89
$275.95
05-GSW-3552-3
Can Am Models 3 ARM SET (Order two for all 6 arms)
35-52
$275.95
Can Am Weights
Zinc Plated
Easily Adjustable
Superior ramp Profile
MAGNETIC
ADJUSTABLE
CLUTCH
WEIGHTS
BMP Heavy Duty Primary Clutch Pullers - $32.95
Stage 2 kit
Heavy duty clutch puller made from hardened steel makes for easy clutch removal!
Available for Sportsman, Ranger, RZR, & RZR XP Models.
RZR 800
Overdrive
Kit
Dayco® XTX (Extreme Torque) ATV Belt
Stage 2 RZR/Ranger with
TAS 03 Secondary
Part Number
Model
Components
Price
07-RNGR500
All Ranger 500
Adjustable Weights, Helix, Primary Spring, Secondary Spring &TAS-03 Secondary Clutch
$719.95
07-RNGR700
07-09 Ranger 700
Adjustable Weights, Helix, Primary Spring, Secondary Spring &TAS-03 Secondary Clutch
$719.95
Introducing the most powerful belt built for the most extreme machines Daycos revolutionary new ATV belts are engineered
for those monster machines powered by 800cc and above engines. Specially-formulated high temperature Neoprene®
with the highest level of Aramid fiber loading available delivers track-churning performance for the most aggressive riders.
This innovative break-through design features deeper cogs on top and rounded cogs on the bottom for ultimate flexibility
and longer belt life. The Dayco XTX belt offersFaster and more consistent throttle response at high speeds Quicker throttle
response at mid-speed acceleration • Greater secondary acceleration at high RPMs • Reduction in slippage during the
highest levels of torque • Increased horsepower capacity • Better performance during deceleration (more responsive engine
braking) Tested and proven reliable at well over 12,000 RPMs • Cooler running than the leading competitors This racetested Dayco XTX belt gives extreme riders the best out-of-the-hole acceleration, throttle response and durability, for the
ride of a lifetime—every time!
Part Number
Model
Price
DC-XTX2239
Polaris RZR 2008-09
$155.95
DC-XTX2248
Polaris RZR S 2009
$155.95
DC-XTX2249
Polaris Ranger 700 2007-09
$155.95
DC-XTX2250
Polaris 2010-12 RNGR 800, 2010-UP RZR 800
$155.95
DC-XTX2251
Polaris RZR XP 900 2011 Models
$155.95
DC-XTX2252
Polaris RZR XP 900 2012-Up Models
$155.95
07-RNGR800
10-13 Ranger 800
Adjustable Weights, Helix, Primary Spring, Secondary Spring &TAS-03 Secondary Clutch
$719.95
07-RZRTMODC
All RZR/RZR S 800
Adjustable Weights, Overdrive Primary Clutch, Overdrive Secondary Clutch,
Clutch Cover Spacer & Belt *Turbo or Big Bore ONLY*
$1195.00
07-RZRA
2008 RZR & 2009 RZR S
Adjustable Weights, Helix, Primary Spring & Secondary Spring
$419.95
07-RZRB
09-12 RZR & 10-UP RZR S
Adjustable Weights, Helix, Primary Spring, Secondary Spring &TAS-03 Secondary Clutch
$719.95
DC-XTX2254
Polaris RZR 570 All Years
$155.95
07-RZRXP
11-Up RZR XP 900
Adjustable Weights, Helix, Primary Spring & Secondary Spring
$419.95
DC-XTX2244
Polaris Sportsman 550 & 850
$155.95
07-RNG900
2013 Ranger 900
Adjustable Weights, Helix, Primary Spring & Secondary Spring
$419.95
DC-XTX2234
Arctic Cat Wildcat All Models
$155.95
07-SP800CK
All Sportsman 800
Adjustable Weights, Helix, Primary Spring & Secondary Spring
$419.95
DC-XTX2236
Can Am Commander/Outlander/Maverick 800/1000
$155.95
07-SP850S2
2009-13 Sportsman 850
Adjustable Weights, Helix, Primary Spring & Secondary Spring
$419.95
DC-XTX2217
Most Kawasaki Models
$155.95
Clutch kits available fore many other make and models. Please call or log on to bikemanperformance.com for more details!
FIND MORE BELTS ONLINE AT BIKEMANPERFORMANCE.COM
114
atv & utv fuel & air
BMP-RZR900I : BMP RZR XP 900 Intake Kit - $275.95
This trick looking billet intake kit improves horsepower on your RZR XP 900.
Tig welded aluminum utilizing heavy duty clamps and boots to ensure no
leaks. Takes place of your stock restrictive intake, yet goes into your stock airbox with the stock filter left in. We dyno tested many designs and combinations and found this to work the absolute best for airflow on a stock, or even
a highly modified RZR. Removing the stock filter HURT performance. Filtered
through a K&N filter through the bed. Includes outerwear. See drop down
menu to add a K&N filter to your stock airbox also!
K&N Air Filter for RZR 900 XP Stock Airbox - $87.95
K&N Replacement Air Filters are ideal for extended use in dirty and dusty off-road riding
and provide clean carburetion even at high altitude. As a rule, no jet changes are required
with just a K&N filter element. K&N replacement air filters are washable and reusable and
provide high air-flow with excellent filtration. An excellent addition to your BMP intake kit!
12-XP900BT: BMP RZR XP 900 Throttle Body Boring - $419.95
Take your performance mods to the next level by having us taper bore your
stock throttle body. We enlarge the inlet 2.25mm and the outlet 3.4mm increasing horsepower and torque on even a stock engine. This is a must have with a
big bore or turbo setup! Intake manifold must be ported to match.
BMP-RZR900INTAKEMAN : Billet Intake Manifolds - $263.95
These billet intake manifolds are a must have for those with big bore or boosted motors. The stock boots are extremely small and do not flow well. When
porting the heads, porting intake boot to match was alway necessary but not
the right thing to do. We finally offer the solution! Providing nearly 50% more
volume and 1/4” longer neck, your guaranteed to pick up horsepower and
torque even on a stock motor. For even better results have us bore your throttle
body and port your cylinder head. Made from billet aluminum. Includes two
billet intake manifolds, manifold boots, and o-rings.
BMP-RZR800I : BMP RZR 800 Intake Kit - $359.95
Maximize your airflow with this BMP Air Intake Kit! Get your filter box out
from under your bed, and install this kit nicely above the bed! 3-4hp gains
with this kit. Comes with K&N Filter with Outerwear along with everything else
pictured. Fits RZR, RZR S, RZR 4 800cc Models.
BMP Billet RZR/Ranger Throttle Body - $419.95
This throttle body is machined from billet aluminum with a port for your 3rd injector
on turbo, or big motor builds. Not only that, but it is taper bored 6mm larger than
the stock size throttle body which will improve power on even your slightly modified
RZR. Some disassembly of your stock throttle body, and assembly of the new one is
required. Oversize intake manifold, or porting of your stock intake manifold is also
required. Works on 2008-2010 RZR, RZR S, RZR 4, Ranger 700, Ranger 800
atv & utv fuel & air
BMP-RZR900HFR : BMP RZR 900 High Performance Radiator - $690
This is a hand built USA radiator that takes the place of the stock radiator, taking it from
a 1 core 1 pass radiator to a 3 core 2 pass radiator. This radiator increases cooling
volume by about 2.5 times the stock offering, and it bolts into the stock location and uses
all the stock hookups. That’s right, stock hoses, stock fan, stock wiring. That means you
can more than double your cooling without reducing the reliability of a stock fan, hoses
or anything about your cooling system. Increase volume, increase surface area, increase
cooling, fits in stock location. Kit comes with hardware and our laser cut spacers.
KO-BA029001-1 : Koso Boost/AFR/Water Temp Gauge - $649.95
This multi-function unit is a great tool for all horsepower enthusiasts that are upgrading
there engine wit ha turbocharger or supercharger. Following many requests we came
up with a unit that combines boost, air fuel ratio and temperature function that can
be installed on the cooling system or the intercooler. This gauge is made to resist cold
temperature, water, or dust. It can easily adapt to many engines with a turbo or supercharger. The X-2 instrument will give you precious information to help you maximize
horsepower and save it from potential damages. For UTV’s and machines that require
longer AFR wires we now offer this exclusive gauge just for you!
BMP-RZR900ER : RZR 900 Speed Limiter Removal Reprogram - $475
Send us your stock ECU and we can raise the rev limit and/or remove the speed limiter.
The stock speed limiter kicks in at 77mph when your machine has much more potential. On
a stock machine we can see upper 80’s and on a turbo or big bore we can see mid to upper 90’s!!! Please let us know all specifics about machine and if it has EPS when ordering.
Programming can take up to 2 weeks.
115
atv & utv fuel & air
116
utv & atv bolt-on performer kits
Power Commander 5
Our Bolt-On Performance kits take your ATV or UTV from mild to wild! We package all of the biggest gains together,
giving you the most bang for your buck. Exhaust and intake modifications are important to gain horsepower, but you have
nothing if that horsepower is not clutched correctly. We have specific clutch setups that come with these kits, meant to gain
the most possible wheel horsepower with modifications. We can set the clutching up for any riding application and tire size.
Power Commander 5’s are all ignition units with higher rev limits, and come pre-programmed. Please specify year and
exact model when ordering. All RZR kits work on 2 seat and 4 seat models. You just cannot beat our horsepower gains for
simple bolt-on parts! Every RZR/Sportsman should have one of these kits! Please go online or call for even more kit options.
The Power Commander V from DynoJet is the latest in EFI control technology, giving you full
EFI tuning capability for your fuel injected ATV/UTV. It allows a fuel map to be built with
input points at 10 different throttle positions and in 250 RPM increments. This provides much
more adjustability than other boxes on the market, allowing us to create fuel maps that
optimize performance and fuel economy for specific combinations. BMP’s fuel maps can be
preprogrammed into the controller for true plug and play capability. For the experienced
tuner, the controller comes with a computer link cable and software for custom mapping
capabilities. No wiring modifications required (OEM style connectors are supplied) and no
permanent changes are made to your stock system. The Power Commander 5 also allows
you to use the Auto Tune module to create a fine tuned custom map for your sled while riding! Combine this with the LCD screen to monitor air/fuel ratio’s and much more!
Part #
Model
Year
Price
DJ-19-013
Polaris Ranger RZR / S FUEL & IGNITION
2008-2010
479.95
DJ-19-013PTI
Polaris Ranger RZR / S FUEL & IGNITION & BOOST
2008-2010
539.95
DJ-19-011
Polaris Ranger RZR / S / 4 FUEL & IGNITION
2011-2014
479.95
DJ-19-011PTI
Polaris Ranger RZR / S / 4 FUEL & IGNITION & BOOST
2011-2014
539.95
DJ-19-008
Polaris Sportsman 800
2005-2010
455.95
DJ-19-014
Polaris Sportsman 850 FUEL & IGNITION
2009-2011
479.95
DJ-19-018
Polaris Sportsman 850 FUEL & IGNITION
2012-14
479.95
DJ-19-012
Polaris RZR XP900 FUEL & IGNITION
2011
479.95
DJ-19-012-PTI
Polaris RZR XP900 FUEL & IGNITION & BOOST
2011
539.95
DJ-19-017
Polaris RZR XP900 FUEL & IGNITION
2012-14
479.95
DJ-19-016
Polaris Sportsman 550 FUEL & IGNITION
2009-2014
479.95
DJ-19-015
Polaris RZR 570 FUEL & IGNITION
2012-2014
479.95
DJ-11-010
Arctic Cat Wildcat 1000
2012-2014
455.95
Part Number
Model
Parts Included
HP Gain
Price
13-RZR900-A
2011-Up RZR 900
BMP Muffler(Hot Rod or Double Barrel), BMP Performance Header, BMP
Intake Kit, BMP Stage 2 Adjustable Clutch Kit, Power Commander 5
15hp
$2035
13-RZR900-B
2011-Up RZR 900
BMP Muffler(Hot Rod or Double Barrel), BMP Performance Header, BMP
Intake Kit, BMP Stage 2 Adjustable Clutch Kit, Power Commander 5, High
Performance Cams
20hp
$2700
13-RZR800-A
2008 STD RZR, 2009
RZR S 800
BMP Full Velocity Exhaust(Black), BMP Intake Kit, Stage 2 Clutch Kit (for models with TAS-03 secondary clutches from the factory), Power Commander 5
10-12hp
$1775
13-RZR800-B
2009-Up STD RZR,
2010-Up RZR S 800
BMP Full Velocity Exhaust(Black), BMP Intake Kit, Stage 2 Clutch Kit (comes
with complete TAS-03 secondary Clutch Assembled), Power Commander 5
10-12hp
$2070
13-RNGR800
Ranger 800 STD/
Crew/6x6
BMP Full Velocity Exhaust(Black), K&N Filter, Stage 2 Clutch Kit (comes with
complete TAS-03 secondary Clutch Assembled), Power Commander 5
8-9hp
$1915
13-RNGR800-P&S
Ranger 800 STD/
Crew/6x6 POWER
AND SPEED KIT
Stage 2 Clutch Kit (comes with complete TAS-03 secondary Clutch Assembled), Power Commander 5. Kit is great for those removing the factory restrictor
plate!!! +7-8mph and huge power.
10-11hp
$1195
13-SP850
Sportsman 850
BMP Slip-On Exhaust(Black), Power Commander 5, Stage 2 Clutch Kit
6-8hp
$1195
RZR 900 Bolt On Kit
Don’t see your model? Chances are we have a PCV for your ATV/UTV/Bike/Sled.
DJ-AT-20 : Auto Tune for PCV - $335.95
Don’t have a dyno tuning center nearby? Are you more of a D.I.Y. (do it yourself ) type?
Are you constantly changing parts on your bike? Once installed, the Auto Tune kit monitors
the fuel mixture (by installing the included Wide Band O2 sensor in the exhaust). It then
sends this information to the Power Commander V and automatically corrects it while you
ride. Each map that we offer has preset Air/Fuel ratio values included that we find to be
the best overall settings. This lets you simply plug in the unit and let it do the work.
DJ-PC-LCD : Power Commander LCD Screen - $359.95
Power Commander LCD connects to any Power Commander via“quick disconnect”cable
and is designed to remain on the machine and is weather resistant. Displays all Power
Commander data “real-time”. Allows storage & swtiching between multiple maps.
Data loggin capable (Requires SD Memory Card, must be purchased seperately). “On
Screen” map adjustments. User comfigurable screens. USB programmable & upgradable. Active Matrix TFT LCD 240x320 16 bit color screen
DJ-PC-MS : Power Commander Map Switch - $59.95
Connecting the optional Map Selection Switch allows the rider to switch between two different maps within the Power Commander. This allows riders to switch between a lean or rich map
depending on altitude or temperature. Comes with handlebar mount.
117
+15HP
118
atv & utv engine products
atv & utv engine products
BMP RZR 935cc Big Bore for RZR XP 900
Our complete big bore has everything you need to turn your stock RZR 900 XP into a dirt shredding monster! This kit comes
with everything to take your 875cc stock machine to the next level of performance. We start off by boring and plating
your cylinders to 96mm making your machine 935cc’s. Then add our German made high quality forged Wossner pistons.
Next we do our professional cylinder head porting to help all those extra CC’s breathe. In addition to porting, we help this
motor breathe with our custom cut high performance stage 1 cams. Don’t forget the exhaust! We set you up with either our
Double Barrel or Hot Rod style slip-on exhausts and performance header. This exhaust package is one of the most powerful on the market! With all those mods your going to need more fuel. No worries, as we have the best fuel controller on the
market; the Dynojet Power Commander 5. We even have a custom tuned map just for this big bore package. Auto tune is
another option to fine tune your machine in at your exact riding location. One thing we can’t forget is making sure this power gets transformed into 100% driven roost in the competitions face. This means we add our high performance, adjustable
Stage 2 Clutch Kit to finish up this 125hp Kit! Huge performance gains that are dyno tested and proven in the real world.
Cylinder exchange required unless you purchase kit outright for $400 extra. If your going with the complete big bore you
will also need to send in your throttle bodies, camshafts for exchange. Your head would also need to be sent in with the
cam caps. Porting is done to your own cylinder head, no exchange. Oil mod is recommended along with us re-shimming the
valves for the high performance cams. For even more details visit bikemanperformance.com.
Part Number
Description
Parts Included
Price
12-XP935
RZR 935cc Big Bore
Exchange Big Bore Cylinders, 2 Pistons, Rings, Circlips, Wrispins, Base & Head Gasket
$1080
12-XP935-COM
RZR 935cc Big Bore
COMPLETE
Exchange Big Bore Cylinders, 2 Pistons, Rings, Circlips, Wrispins, Base & Head Gasket,
Head Porting, Billet Oversize Intake Boots, BMP Custom Camshafts, Stage 2 Adjustable
Clutch Kit, Power Commander 5, BMP Intake Kit, BMP Throttle Body Boring, BMP Header
Pipe, BMP Slip-On Muffler (Hot Rod or Double Barrel, Ceramic Chrome or Black)
$4795
Recommended Options
Description
Price
Quiet Cap for muffler
$35.95
Purchase Cams Outright
$192
Purchase Cylinder Outright
$480
BMP Oil Mod (Must send cam caps)
$54
Valve Shimming for Cams (Send head & caps)
$240
Cam Chain Tensioner Gasket
$5.00
Valve Seals
$18.00
Water Pump Gaskets
$9.50
Exhaust Header Gaskets
$18.00
BMP RZR 800 82mm Big Bore Kit - $795
Increase your horsepower and torque with this big bore kit from BMP! We bore out your stock cylinders to 82mm, and
send you on your way with a Cometic gasket kit. The extremely high quality forged Wossner pistons are available in
either a 12:1, 10.5:1 or 9:1 compression ratios. 12:1 compression requires 110 race fuel, 10.5:1 requires only pump
gas, and the 9:1 would be for turbo machines. This is an exchange cylinder program, however you may purchase the kit
outright for only $350 extra! Head porting and our high performance camshaft are very good options for this kit. For
the best performance results go with our complete big bore kit. This includes everything you need to make your stock RZR
into a horsepower monster! This is the same kit we use on our GNCC RZR 800 which beats up on 900 RZR’s all day long!
If purchasing the complete big bore we will need your head, camshaft, and cylinder. Non-complete kit will also work with
sportsman and ranger 800 models. Please call or go online for kit options for your sportsman or ranger 800.
Part Number
Description
Parts Included
Price
12-RZR82MMBB
RZR 800 82mm Big Bore
Exchange Big Bore Cylinders, 2 Pistons, Rings, Circlips, Wrispins, Base Gasket,
Head Gasket, Exhaust Header Gasket
$959.95
12-RZR82MMBB-COM-B
RZR 800 82mm Big Bore
COMPLETE for 2008 RZR
& 2009 RZR S Models with
TAS-03 Secondary Clutch
Exchange Big Bore Cylinders, 2 Pistons, Rings, Circlips, Wrispins, Base Gasket,
Head Gasket, Exhaust Header Gasket, High Performance Camshaft, Cylinder
Head Porting, Adjustable Clutch Weights, Primary Spring, Secondary Spring,
Helix for TAS-03 Secondary, BMP Full Exhuast System(Black), BMP Intake Kit,
Power Commander 5
$3650
12-RZR82MMBB-COM-B
RZR 800 82mm Big Bore
COMPLETE for 2009-Up
RZR 800 Models without
TAS-03 Secondary Clutch
Exchange Big Bore Cylinders, 2 Pistons, Rings, Circlips, Wrispins, Base Gasket,
Head Gasket, Exhaust Header Gasket, High Performance Camshaft, Cylinder
Head Porting, Adjustable Clutch Weights, Primary Spring, TAS-03 Secondary
Loaded with Helix & Spring, BMP Full Exhuast System(Black), BMP Intake Kit,
Power Commander 5
$3995
Optional:
Oversize Throttle Body
Oversize Throttle Body for 2008-2010 RZR Models
$419.95
125hp
rzr900
RZR XP1100cc BIG BORE FOR RZR 1000 IS COMING SOON
119
One of the only big bores available with high, standard, or low compression turbo pistons
120
atv & utv engine products
Wossner High Performance Forged Pistons
Extremely high quality German made Wossner pistons! We have been using Wossner to make our high performance pistons
for motors running over 40psi of boost, high RPM two strokes and so much more. The quality and durability just can not be
beat! We offer this quality piston kit for your RZR, Ranger or Sportsman 800 model. Whether you have a big bore and
need replacement pistons, or you have a stock motor that is in need of pistons.... we have one for you! you covered! Piston
kits come with 2 pistons, rings, circlips, and wristpins. Check out the gasket options below for more compression ratio options.
Model
Piston Size
Compression
Price
RZR/Sportsman/Ranger 800
80mm Standard Bore
10.5:1 (Pump Gas)
$409.95
RZR/Sportsman/Ranger 800
80mm Standard Bore
9:1 (Turbo)
$409.95
RZR/Sportsman/Ranger 800
82mm Big Bore
10.5:1 (Pump Gas)
$409.95
RZR/Sportsman/Ranger 800
82mm Big Bore
9:1 (Turbo)
$409.95
RZR/Ranger 900
93mm Standard Bore
10.5:1 (Pump Gas
$455.95
RZR/Ranger 900
96mm Big Bore
10.5:1 (Pump Gas)
$455.95
Top End Gasket Kits
High quality gaskets that meet or exceed OEM specs. 800 kits include head gasket, base gasket, and exhaust header gasket. 900 Kits include base gasket, head gasket, 2 cover gaskets, 1 chain tensioner gasket, 2 exhaust gaskets & 8 valve seals.
800 kits are available in 2 different bore sizes, while 900 kits are availbe in 2 different bore sizes and compression ratios.
Model
Head Gasket Size
Compression
Price
RZR/Sportsman/Ranger 800
80mm Standard Bore
10.5:1 (Pump Gas)
$83.95
RZR/Sportsman/Ranger 800
82mm Big Bore
10.5:1 (Pump Gas)
$83.95
RZR/Ranger 900
93mm Standard Bore
10.5:1 (Pump Gas
$99.95
RZR/Ranger 900
93mm Standard Bore
8.75:1 (Turbo)
$99.95
RZR/Ranger 900
96mm Big Bore
10.5:1 (Pump Gas
$99.95
RZR/Ranger 900
96mm Big Bore
8.75:1 (Turbo)
$99.95
BMP-RZR900VS - RZR 900 High Performance Valve Springs - $479.95
Valve Spring set is designed for high-lift cams for RZR modified engines. Heat treated alloy
retainers and seats. Run tested spring rates available online.
BMP RZR Cylinder Head Porting
BMP professional cylinder porting for you RZR is the ticket in adding more power to your motor. This is a must when running a high compression or big bore setup! Also helps a great deal
with turbo motors because you can get more air volume behind the valves, meaning more air
in! 6-8hp Increase. ***RZR 900 Owners Must Purchase Billet High Flow Intake Manifolds***
BMP High Performance Camshafts
These camshafts are meant for the highest possible all around horsepower gains while using the stock valvetrain. No spring
change is needed when switching to these high performance camshafts! Huge low end and top end increases. Works exceptional with our big bore and porting. Some models require cam core to be sent in. Please see below chart.
Model
Year
Exchange
Price
RZR XP 1000
2014
YES
$719.95
RZR XP 900
2011-UP
YES
$689.96
RZR/RNG/SPRTSMN 800
2006-10
NO
$359.95
RZR/RNG 800
2011-UP
YES
$359.95
Ranger/Sportsman 700
All
NO
$299.95
Ranger/Sportsman 500
2005-UP
YES
$359.95
utv turbo kits
121
BMP RZR XP 900 Cyclone Turbo Kit - $5755
If your serious about power, this is the kit for you! Countless hours of design and testing went into this kit to deliver what we
think is the best XP 900 turbo kit on the market! This is one of the most complete kits out there. We include everything you
need! Our kit utilizes the Power Commander 5 fuel controller for more precise tuning compared to most other fuel controllers. We are able to tune fuel, fuel based upon boost, timing, and timing based upon boost. Using larger injectors, instead
of adding injectors saves a lot of time and unnecessary parts.
Kit Includes:
Garrett Turbocharger
Stainless Braided Oil Lines
Water to air intercooler with water pump & hoses
Heat exchanger with mounts for roll cage
Blow Off Valve
Koso Digital Boost, Air/Fuel/Water Temp Gauge (all in one unit)
BMP Intake Manifold
BMP Ceramic coated muffler with billet endcap
BMP Stainless Steel mid pipe
Power Commander 5 PTI
Oversize Fuel Injectors
BMP Turbo Clutch Kit with adjustable weights
All hoses and fittings needed to install kit
BMP Cyclone Turbo Kits for RZR 800, Ranger 700, & Ranger 800
Here at BMP we have developed just what you’ve been looking for. Easy bolt on performance at a lower cost, without sacrificing reliability and doubling your stock horsepower! BMP Turbo Kits are second to none and are a true complete kit including
full exhaust. We utilize a top of the line Garrett turbo charger which is the center of your power boost. Connected together
with a BMP performance 2 into 1 header and our high flow silencer for maximum horsepower gains. Due to the location of the
turbo, low volume charge circuit, & short header length this turbo kit is one of the fastest spooling, most responsive kits on the
market. That makes it great for any type of riding. Please go online to see kit specifics.
Starting @ ONLY $3595
122
harley performance
BMP HD 107” Big Bore for 96” & 103” Twin Cam Motors - $call
107 Badd Azz Budget Kit: This kit makes serious power gains for seriously not alot of money, especially compared to other kits on the market. This kit is for 96 and 103 twin cam motor will crank out 120 ft lbs of torque
and 110 hp! Thats nearly 40 more lb/ft of torque and horsepower over stock!! Simply send BMP your cylinders,
heads and throttle body. We will extensively hand port your cylinder heads and throttle body manifold outlets,
then bore out your cylinders. We will return them to you along with a new Cometic top end gasket set, cam cover
gasket, adjustable pushrods with chome quick install covers, forged pistons, and smooth running Wood .575 lift
powerful camshafts. These kits have tons of torque to make your Harley hit hard when you twist the throttle, but
nice and smooth for long cross country rides. Very reliable and powerful engine kit!
harley performance
123
Harley Twin Cam Bolt-On Performer Kit - 2008-12 $Call Muffler Mod, $call Slip-On
Harley Twin Cam Bolt-On Performer Kit 999-07 - $Call Muffler Mod, $call Slip-On
Kit Includes Boyesen X Intake or Big Sucker Intake (Depending on model), Power Commander, Slip-On Mufflers or
Muffler Mod. +15-18 horsepower!!!! If sending in mufflers for muffler mods please send with a copy of your receipt.
Other BMP Big Bores
Big Bore Kit
Price
103” Budget
call
107” Hell Raiser
call
98” Big Bore
Call
95” Big Bore
Call
114” Big Bore
Call
124” Big Bore
Call
Muffler Mod for 2006-11 Non Cat Converter Models - $call
Why spend 400-500 dollars on mufflers when you can have your stock bagger mufflers recored by us for $199.95?!? We have spent many hours on our Dynojet motorcycle dyno perfecting our baffles and we have outdone the competition. We were
suprized how poorly the Screaming Eagle mufflers actually performed and sounded.
You can install our recored mufflers with no fuel or jetting changes and get 5-6
horsepower over stock. We offer a standard and big bore version. They have a nice
smooth sound for cruising, but bark nicely when you get on the throttle! Not stupid
loud, but just right. You Can can purchase muffler mods outright for $100 more.
Freedom Exhaust Systems
BMP is proud to offer Freedom exhaust systems for your Harley Davidson bikes. We found some of the best horsepower
and torque gains with these great slip-on and full systems! Please log on to BikemanPerformance.com to view all exhaust
systems available!
Arlen Ness Big Sucker Inakes - Starting at $call
These kits are designed to be used with the stock outer air filter cover (except sportster and
08-11 FXD models). Sportser models require the purchase of a custom outer air cleaner
cover. Kits can be used as an exposed filter design when using one of our stage 1 billet
covers. Offers up to 20% more power! Please go online to view all options!
Boyesen X Series Air Cleaner - $call
THE ULTIMATE IN MANAGED AIR FLOW DELIVERY! BOYESEN’S POWER X-INTAKE SYSTEM DELIVERS. AIR IS POWER,
AND BOYESEN HAS CHANNELED THAT POWER LIKE NEVER BEFORE. WITH ITS REVOLUTIONARY DESIGN AND EASE OF
INSTALLATION, ADDING MORE POWER AND GREATER ACCELERATION IS NOW WITHIN YOUR REACH. AVAILABLE FOR
08-11 HARLEY DAVIDSON TOURING MODELS. IMPORTANT: SE stage-1 ECM recalibration is recommended when installing
this kit. Intake Body available in nickel or black finish and your choice of no cover, chrome cover, or black cover. For use on
all 2008-Up 50mm throttle by wire twin cam motors.
Complete Bolt-On Kit:
» Backing Plate, Filter and Mounting Hardware
» X-Wing Venturi Design for MORE POWER and ACCELERATION
» X-Wing Design Increases Air Speed for Added Throttle Response
» Oil Free / Washable Filter Media - Polyester Cotton Blend
» X-Large Filter Area for Increased Airflow - Filters to 40 microns
» One Piece Precision Casting with Internal Breather Passages
» O-ring Assembly
» Accepts Stock Filter Cover