OpenInsight Install Guide

Transcription

OpenInsight Install Guide
OpenInsight Install Guide
Version 9.2
A Division of Revelation Technologies, Inc.
COPYRIGHT NOTICE
© 1996-2010
Revelation Technologies, Inc. All rights reserved.
No part of this publication may be reproduced by any means, be it transmitted, transcribed, photocopied, stored in a
retrieval system, or translated into any language in any form, without the written permission of Revelation
Technologies, Inc.
SOFTWARE COPYRIGHT NOTICE
Your license agreement with Revelation Technologies, Inc. Authorizes the conditions under which copies of the
software can be made and the restrictions imposed on the computer system(s) on which they may be used. Any
unauthorized duplication or use of any software product produced by Revelation Technologies, Inc., in whole or in
part, in any manner, in print or an electronic storage-and-retrieval system, is strictly forbidden.
TRADEMARK NOTICE
OpenInsight is a trademark and Advanced Revelation is a registered trademark of Revelation Technologies, Inc.
Windows 2000®, Windows XP Professional®, Windows 2003® Windows 2008, Windows Vista Business® and
Windows 7 Ultimate® above are registered trademarks of Microsoft, Inc.
Part No. 102-955
Printed in the United States of America.
2
Table of Contents
SECTION I: BEFORE YOU BEGIN....................................................................................................... 4
SECTION II: RUNNING THE INSTALLATION ON THE SERVER ............................................... 5
SECTION III: UPGRADING YOUR WORKSTATIONS .................................................................. 10
SECTION IV: SETTING YOUR OIPI VERSION............................................................................... 16
3
Section I: Before you begin
1.
Locate your installation authorization code that you received from Revelation Software or your authorized
reseller. You will need this authorization code to activate the upgrade process.
2.
Close all non-essential Windows programs.
3.
Stop the OEngineServer and OETelnetServer services from previous OpenInsight installations if
applicable.
4.
This software will only run on Windows NT, 2000, XP Professional, Vista Business 32&64-bit, Vista
Ultimate 32&64-bit, Windows 7 Ultimate 32&64-bit, 2000 Server, 2003 Server or 2008 Server.
5.
OpenInsight 9.1 and above includes a client install process. When initially installing the 9.1 (either a full
install or an upgrade), the client files can be installed on the ‘server’ (where OpenInsight is being installed
or upgraded) automatically at the end of the setup process. On other workstations, administrators must
point to the OpenInsight directory on the server and run the ClientSetup.exe file.
Before running the clientsetup.exe routine for the first time, any existing OI.NET routines should be
removed from the workstation. This can be done from the Add/Remove Programs on the individual
workstations, and the OIPINETSetup, RevDotNet, and NetOI (if present) should be removed in this
fashion. Once these have been manually removed, using the clientsetup.exe will ensure that in the futire
this manual process need not be done again.
In the future, when new versions of OpenInsight are released (either through upgrades or full installations),
the workstations must have clientsetup.exe run on them after each OpenInsight upgrade/install (to remove
the previous versions, and add in the new versions, of the .NET routines, and any other files we wish to
copy to or register on the workstations). The clientsetup.exe will at that time, as described above, remove
the already-installed versions and install the newly-installed versions.
6.
4
Extract the install from the installation zip file.
Section II: Running the installation on the server
7.
Execute the Setup.exe from within the location to which the upgrade was extracted.
5
6
7
8
9
Section III: Upgrading your workstations
8.
10
Execute the ClientSetup.exe from within your OpenInsight directory.
11
12
13
14
15
Section IV: Setting your OIPI version
1.
16
By default OpenInsight 9.2 will utilize OIPI.NET as the print engine. You can configure your system to
use OIPI by changing the VSPRINTER2 setting in the SYSENV table to VSPRINTER. From the
SYSPROG application open the System Editor.
2.
Select Open, Record.
17
3.
18
Choose the SYSENV table and the CFG_OIPI record.
4.
If you want to utilize OIPI.NET set field 1 of the CFG_OIPI to VSPRINTER2. Save the record, close
OpenInsight. Your changes will take effect when OpenInsight is reopened.
19
5.
20
If you want to utilize OIPI set field 1 of the CFG_OIPI to VSPRINTER. Save the record, close
OpenInsight. Your changes will take effect when OpenInsight is reopened.
Revelation Software, Inc
99 Kinderkamack Road Ste 109
Westwood, NJ 07675
U.S.A
Toll Free: 800-262-4747
Phone: 201-594-1422
Fax: 201-722-9815
www.revelation.com
Revelation Software Ltd.
45 St Mary’s Road
Ealing,
London, W5 5RG
U.K.
Phone: +44 0 208 912 1000
Fax: +44 0 208 912 1001
[email protected]
Revelation Software Australia Pty
Ltd.
PO Box 300
Brookvale, NSW 2100
Australia
Phone: +61 2 8003 4199
Fax: +61 2 9332 6099
[email protected]
Revelation Software is a division of Revelation Technologies, Inc.
Part No. 102-955
21