Watch Testing Equipment

Transcription

Feb 5, 2014
Watch
Testing
Equipment
PERRIN
H&W Perrin Co. Ltd.
E-mail: [email protected]
90 Thorncliffe Park Drive
Toronto, ON
M4H 1N5
www.Perrin.ca
Phone: 416-422-4600
1-800-387-5117
Fax: 416-422-0290
1-800-741-6139
Witschi Watch Testing Equipment
Page 1
Equipment for Mechanical Watches
#64-76835-3-110 Watch Expert lll with Stand Microphone
The "Watch Expert lll" with stand microphone is an economical
measuring instrument ideally suited for testing mechanical
watches. Results are displayed noiselessly on the new
illuminated, LCD graphic display. Measured values for rate
deviation, amplitude and beat error are automatically
calculated and displayed numerically. This instrument can
automatically recognize the beat number of all watches.
Appropriate measuring modes are available for watches with special
escapements such as co-axial or AP. Accessories are also available.
Features include:
►Measurement possibilities:
Rate deviation, amplitude, beat error shown by a diagram of beat noises.
►Beat error:
Automatic selection of all common beat numbers. Manual selection of less common beat numbers. Manual selection of
any beat number between 3,600 and 43,200 b/h. Determines unknown beat numbers.
►Measuring modes:
A standard mode for watches with Swiss escapements plus modes for watches with co-axial or AP escapements
and a mode with specific amplitude filter.
►Gain Control:
Automatic gain control plus a manual control for watches with stray or unusual beat noises.
►Display:
Continuous diagram recording of the beat noises and display of the numeric values for the rate accuracy, amplitude
and beat error. The VARIO display mode provides fast overview of the quality and stability of the rate and amplitude
over long periods of time (maximum 100 hours).
►Microphone:
Supplied with a multi-positional stand microphone.
#64-76836-110 Chronoscope S1 with Stand Microphone
Chronoscope S1 with stand microphone is the instrument for effective
and professional testing of watches. Noble design and functional layout
of the operating elements and the large LCD display provide a comfortable
handling of the instrument. Different display modes as well as the
graphic presentation of the beat noises are available. The VARIO
display mode provides fast overview of the quality and
stability of the rate and amplitude. Accessories are also available.
Technical Data & Features:
►Measurement Possibilities:
Rate deviation, amplitude and beat error of mechanical watches. Diagram recording of the beat noises.
►Beat Number:
Automatic selection of all common beat numbers. Manual selection of any beat number between 3,600 and 43,200 b/h.
►Measuring modes:
Standard mode for watches with Swiss escapement, Special 1 Mode for watches with coaxial escapement. Special 2
Mode for watches with AP escapement, Special 4 Mode with a specific amplitude filter for the measurement of watches
with specific amplitude filters.
►Gain Control:
Automatic and, Manual control facility for watches with stray or unusual beat noises.
►Display Modes:
Continuous diagram recording of the beat noise. Measured values for rate deviation, amplitude and beat error are
displayed numerically. Vario Rate and amplitude stability check over a long time range (maximum 100 hours).
Graphic display of beat noises with adjustable time interval: 20, 200, 400 ms.
►Microphone: Supplied with a multi-positional stand microphone.
Page 2
#64-76838-110 Chronoscope X1 with automatic Microphone
The Chronoscope X1 is the top of the line Mechanical Watch Testing
Instrument. Chronoscope X1 can be used in a manufacturing
environment, by the repair service or in the watch testing lab. The
10.4" colour touch screen provides intuitive and easy operation.
Automatic test cycles with up to 6 measuring positions are possible
with the "Micromat C" microphone. It provides 4 different display
modes as well as a graphical representation of beat noises. PDF files
can be individually stored with each measurement program. They can
contain e.g. mounting diagrams, limit data, lubricating schedules etc.
and can be called back whenever necessary. The X1 terminal is used as the control and display unit.
Its large screen provides three content-ordered menu bars with big, self-explanatory buttons around
the main display. The 4 display modes show measurements in a way adapted to any individual
requirement. The measurement results can be printed on an external printer (not included) without
interrupting the on-going measurement process. It is possible to create up to 99 different
measurement programs. The automated" Micromat C" microphone can be operated directly from the
terminal or with its own function keys. Accessories are also available.
Technical Data & Features:
►Measurement Possibilities:
Rate deviation, amplitude and beat error of mechanical watches, diagram of beat noises
►Beat Number:
Automatic selection of all common beat numbers. Manual selection of any beat number between 3,600 ando 72,000 b/h.
►Measuring Modes:
Rate only - measurement of the rate accuracy
Standard mode for watches with Swiss escapement, Special 1 Mode for watches with coaxial escapement.
Special 2 Mode for watches with AP escapement, Special 4 Mode with a specific amplitude filter for the measurement
of watches with specific amplitude filters. Special 6- Mode for Chronograph "Foudroyante"
►Gain Control:
Automatic. Manual control facility for watches with stray or unusual beat noises.
► Micromat C Microphone:
Automatic Microphone with built in measuring electronics. The microphone, by means of
a inserted joystick, is manually (up to 10 test positions) selectable, also in automatic Sequence mode.
#64-76839 "Micromat C" System
The Micromat C system is a motorized multi-position microphone containing the
entire Chronoscope measuring technology. It can be directly connected to a
Computer by a USB interface. This instrument is characterized by its user-friendly
design and small size. It is characterized by a new feature, the computation and
display of balance wheel’s center of gravity faults. The Micromat C motorized
microphone is supplied with the required software to set up your PC.
This unit will have all the functions of the Chronoscope X1.
#64-76845-120 Teslascope
The new Teslascope performs the tests for a successful demagnetization and
detection of the magnetic state of mechanical watches in a single step. The
Teslascope includes a convenient, freestanding support, allowing watches with
or without bracelet, movements and steel watch parts of small dimensions are
easily tested.. The degree of magnetization is represented a row of LED's. This
is an extremely user friendly demagnetizer.
Equipment for Quartz Watches
#64-76833-2-110 New Tech Handy ll
New Tech Handy II is designed by Witschi Electronics
for the Watch Repair Service. The Watchmaker needs
a test instrument with a simple way to perform electrical
measurements and tests on quartz watches.
This instrument provides all measuring and test facilities
required in a professional search for defects in quartz
watches. Operation is very easy due to automated
measurement functions, the functional layout of
operating elements and the highly readable results
and parameters illustrated on an illuminated display.
This New Tech Handy II measures Rate Accuracy,
Current Consumption and allows individual tests of
the components of quartz watches. Sensors are of
the highest sensitivity and selectivity for acoustical,
magnet and capacitive signals. New Tech Handy II
is supplied with a movement holder, contact probes, wire set and probe tips.
#64-76846-120 "Analyser Twin" Quartz & Mechanical Tester
Analyzer Twin Quartz and Mechanical Watch Tester.
This combined measurement and test instrument
associates all functions of test equipment for quartz
watches and test equipment for mechanical watches.
It is the ideal test instrument for the repair service, and
watch sales outlet. Basic functions and measurement
sequences, largely automated, provide a fast and efficient
operation. Additional measurement modes provide a
way to measure watches with special escapements.
The instrument is based on the "all-in-one" concept and
only requires a very small work area.
#64-76847-120 Analyser Q1
The ‘Analyzer Q1" performs rate measurement of both
quartz and mechanical watches. Unit also performs a
range of tests for quartz movements such as current supply,
current measurement, resistance, cell voltage with load control,
pulse analysis, and also includes a pulse generator. Measuring
cycles are largely automated. The combined rotating/push button
provides a simple and quick parameter setting. The ergonomic
and functional layout of the operating elements and the large LCD
display significantly improve user-friendliness.
Page 3
#64-76000 Witschi "ChronoCube®" Timing Machine
Insert watch, touch sensor, job done.
The ChronoCube® is revolutionary in user-friendliness, quality and
design. It measures rate variation, amplitude and beat error in
mechanical watches in five measuring positions and sends the
measurement results to your computer. You can read the
information from the screen or send it to print.
The unit automatically detects all current beat numbers (frequencies)
between 12,000 and 72,000. The Chronocube® is a masterpiece of
elaborate precision technology and convenient handling.
No extensive staff training courses, no complicated operating
instructions. Unit is supplied with software.
The Chronocube® is designed with the retailers of fine watches
in mind. This machine allows the retailer to run their own
diagnostic check before releasing a watch to the customer. If
desired a printout of the results can even be printed and
presented to the customer along with their watch. This machine
would grace any sales desk thanks to its timeless good looks.
Witschi ChronoProof® Waterproof Tester
The Simplest Waterproof Test Ever.
The ChronoProof® turns you into a specialist, able to reliably
waterproof test all types of wristwatches in no time. Just insert
the watch, close the test chamber and the rest takes place
automatically. Designed with the retail stores in mind, this unit
allows the watch to be quickly and easily waterproof tested
after services such as battery changes etc.
This unit features the first ever built-in compressor. You don’t
need a degree in rocket science to operate the Chronoproof®.
Available with or without an integrated printer, which would
allow a print-out of results on paper. Print-out can be
personalized with store name or logo at the top.
#64-76200 ChronoProof® with Printer
#64-76300 ChronoProof® without Printer
#64-76843-120 Witschi PROOFMASTER "M"
The Proofmaster M is the most recent instrument in the leak test instrument family.
It is characterized by its wholly automated "close & test" sequence, its intuitive
operation with a colour touch screen and also its excellent design.
The Proofmaster M tests watches with or without bracelet attached, up to a
diameter of 70 mm and a height of 28 mm. The leak test is based on the
deformation principle same as proofmaster S. Can be interfaces with an optional
Witschi thermo printer. An 11 bar compressor is required for positive pressure testing
(must be an oiless type with a water separation system or damage will occur).
The unit has a built-in vacuum pump for negative pressure testing.
Designed for the manufacturing industry.
Page 4
Page 5
#64-76842-120 Witschi PROOFMASTER "S"
The Proofmaster S checks the leak resistance of a watch by means of the
Deformation principle. The watch to be tested is placed in a highly sensitive
measuring system which constantly monitors the thickness of the watch.
The watch is subjected to the specified test pressure once the measurement
chamber has been closed. The pressure causes a certain amount of
deformation of the watch. This deformation remains constant in the case of a
fully sealed watch provided that the pressure remains constant. In the case of
a leaky watch the air seeping into the watch case results in an internal pressure
equalization which relaxes the deformation. The Proofmaster S has automatic
test cycles with vacuum and/or pressure, during which all types of leakage are
positively identified. Proofmaster S has 7 fixed test programs and 10 test programs with choice of
test parameters such as pressure, tolerances, test time and test sequence. Tests up to 10 bar. Backlit
LCD screen displays in choice of 9 languages.
Can be interfaces with an optional Witschi thermo printer. An 11 bar compressor is required for
positive pressure testing (must be an oiless type with a water separation system or damage will occur).The unit
has a built-in vacuum pump for negative pressure testing. Designed for the service industry.
#64-9791102 11 bar Compressor JunAir 6-10
Compressor with safety outlet, water separator
& 10 liter rustproof reservoir, 120V
#64-9791103 Panther P50 8 bar Compressor
when operating under full load this ultra-silent Panther P50 air compressor offers tremendously low noise levels at 40
db/A ( 20% quieter than normal conversation levels) and comes equipped with powder coated air tank, pressure switch,
1-micron air filter, regulator, and pressure gauges for completely automatic and trouble free operation.
Output in CFM and L/Min
Horse Power
Tank Size Gal / Lt.
Noise Level
Power Requirements
Dimensions
Weight
Max Pressure PSI / Bar
Operating Pressure PSI / Bar
:2.1CFM / 60 L.Min
:0.5Hp
:6.3Gal / 24 Lt.
:40 db/A
:115 V / 50-60 Hz or 220 V / 50-60 Hz
:16" x 16" x 27"
:62Lbs.
:120PSI / 8 Bar
:90-120 PSI / 6-8 Bar
PERRIN
H&W Perrin Co. Ltd.
Toronto, ON
M4H 1N5
www.Perrin.ca
Phone: 416-422-4600
1-800-387-5117
Fax: 416-422-0290
1-800-741-6139
Elma Watch Cleaning Machines
Page 6
#64-1055851 Elmasolvex-SE Manual Watch Cleaning Machine
A classic has been reinvented.
Elma introduces the next generation manual watch cleaning machine.
This machine cleans by agitation only with a reversing spin action.
It features a 4 jar system plus warm air drying chamber. The basket is
moved manualy from jar to jar. Basket is raised and lowered by means
of a simplified, front mounted handle. Basket locks into raised or
lowered position when handle is released. The head of the machine
pivots manualy to position over the individual jars. Simplified controls
for preselecting settings are mounted on top of machine head.
Machine is equiped with a connection for attachment to an exhaust
system for venting fumes. (exhaust systen not included)
Supplied with 4 - 600ml. jars with rim seals and lids, plus 4 wave
breakers to resist solution spin and create maximum turbulence within
the jars.
Cleaning baskets sold separately.
#64-1055855 Elmasolvex-RM Automated Watch Cleaning Machine
Elma introduces the next generation automated watch cleaning machine.
This machine cleans by rotation or oscillation. It features a 4 jar system
plus warm air drying chamber.
The RM machine will run on a preset program or individual settings can
be programmed for each jar. Once activated the machine will proceed
through the program, moving from jar to jar. Just start and forget!
The RM features 2 different cleaning modes…rotation and oscillation.
Rotation is used with the parts basket for watches that have been
disassembled. Operating with a traditional reversing rotation.
Oscillation is used in conjunction with the multi-movement holder and
is for cleaning complete assembled movements. A back and forth
oscillation is used. Oscillation frequency is adjustable. Controls are
mounted on the face of the machine and are simple and easy to use
Machine is equiped with a connection for attachment to an exhaust
system for venting fumes. (exhaust systen not included)
Supplied with 4 - 600ml. jars with rim seals and lids, plus 4 wave
breakers to resist solution spin and create maximum turbulence within
the jars.
Cleaning baskets sold separately.
#23-2310 Elma Cleaning Basket
#64-2308 Elma Multi-movement Holder
Cleaning basket for use with the
Elmasolvex RM & SE and
Super-Elite machines.
Consists of plastic frame and 3
stainless mesh trays, a small parts
basket with screw top and lid. 2 of
the trays are partitioned.
Trays are 64mm diameter.
Holder for 6 assembled
Movements.
For use with the
Elmasolvex SE & RM
cleaning machine.
Elma Watch Cleaning Machines
Page 7
#64-1052330 Elmasolvex-VA Ultrasonic Watch Cleaning Machine.
Revolutionary new ultrasonic watch cleaning machine from Elma.
Elma has thrown out the traditional ideas and thought outside the box.
The first big difference is that there are no jars. Cleaning takes place in
a vacuum chamber at the top of the machine. Solutions are stored in 4
separate containers in the base of the machine. Solution containers are
easy to remove and install and feature integrated particle filters for
increasing the service life of solutions. As the machine proceeds through
the cleaning and rinse cycles, a vacuum draws the solutions in sequence
up into the cleaning chamber where the basket is rotated and subjected
to ultrasonic waves. Cleaning cycles at 40KHz and rinse cycles at 80KHz.
Basket is spun dry at 1000 RPM between cycles and at 1400 Rpm
before drying. Use of vacuum also eliminated interfering gas bubbles in
the solutions and on the movement. All aspects of the clean and rinse
cycles can be programmed using the integrated high-resolution colour display.
Exhaust gases can be filtered through an activated charcoal filter system (optional) or through an
existing exhaust system.
ELMA Watch Testing Equipment
#64-1022803 Elma Watch Master ll
Rate measurement for quartz and mechanical watches. Offers all test
measurement functions required for a skilled service diagnosis of quartz
watches. The functional layout of operating elements and the logical
display of results and parameters greatly simplify the use of the equipment.
The measurement process, largely automated, and the warning tone
signaling a wrong operation make this tester very easy to use. Supplied
with movement holder, contact probes wire set and probe tips.
#64-1022711 Elma Watch Matic lll
The watch Matic III is an economic measuring instrument ideally
suited for testing mechanical watches. The diagram is displayed
noiselessly on the new, illuminated LCD graphic display. Measured
values for rate deviation, amplitude and beat error are automatically
calculated and displayed numerically. The beat number of all common
watches will be automatically recognized. Appropriate measuring modes are available for
watches with special escapements. Two novelties: the additional display mode „VARIO“
and the storage of the last 5 screen contents, which later are recallable.
ELMA Watch Testing Equipment
Page 8
#64-4000003 Elma Profi-Check
External non-contact drive for analogue quartz watches. The machine generates a
magnetic rotating field with variable intensity and rotational speed around the watch
support. As soon as an analogue quartz watch is put in the range of influence of this
rotating field, the magnetized rotor of the pulse motor also starts rotating. This allows
very fast movement of the going parts without opening the watch. This will often
unstick movement that have been inactive for a period of time and pivots have
become set in place.
Elma Waterproof Testing Equipment
#64-1024003 ElmaSpheric Waterproof Tester
The ElmaSpheric checks the water resistance of a watch by means of the deformation
principle. The watch to be tested is placed in a highly sensitive measuring system
which constantly monitors the thickness of the watch. The watch is subjected to the
specified test pressure once the measurement chamber has been closed. The
pressure causes a certain amount of deformation of the watch. This deformation
remains constant in the case of a fully sealed watch provided that the pressure
remains constant. In the case of a leaky watch the air seeping into the watch case
results in an internal pressure equalization which relaxes the deformation. The
ElmaSpheric has automatic test cycles with vacuum and/or pressure, during which all
types of leakage are positively identified. ElmaSpheric has 7 fixed test programs and 10 test
programs with choice of test parameters such as pressure, tolerances, test time and test sequence.
Tests up to 10 bar. Backlit LCD Display. Displays in choice of 9 languages. Can be interfaces with a
thermo printer. Compressor required (must be an oil-less type with a water separation system or damage will occur)
#64-6401 Elma "Leak-Controller"
This machine is designed to indicate if a watch is leaking or not leaking. Absolutely
no water is used with this tester, therefore there is no risk to the watch. This test can be
performed quickly and easily. The leak controller uses negative pressure (vacuum).
The watch is placed in the machine and a sensitive micrometer is set in contact with
the crystal. Place the dome on the machine and create a vacuum by means of a built-in
vacuum pump. If the case is waterproof the micrometer will measure a deflection in the
crystal surface and this measurement will remain steady. If there is a leak no deflection
will register on the gauge or if there is a minor leak the deflection will subside. This type
of negative pressure testing will not allow you to control the ATM at which you are testing.
Elma Watch Equipment
#64-1012964 Elma "Antimag" Demagitizer
Electronic demagnetizer for watches and precision tools.
Very simple, one touch operation. Elma Antimag demagnetizes complete watches,
disassembled movements or watch tools within milliseconds.
160 x 130 x 60 mm.
Made in Germany.
Elma Watch Equipment
Page 9
#64-67130 Elma "Checkimpulse"
An easy to use diagnostic tool for quartz watches. This devise checks for the
impulses which are given off by the circuit and coil. This device can be used
without even opening the watch. Place watch on the marked area and push
the button. If the electronic side of the movement is functioning flashing light
will indicate impulses. If no impulse open watch and check cell. If cell is dead,
replace cell. If cell is OK then there is a problem with the circuit or coil. If
watch is impulsing and hands do not move, then there is a problem with
mechanical side of the watch. Often the wheels are just stuck and simply
need a push to proceed. The Checkimpulse can be used to provide that push.
In the impulse mode the unit sends out an accelerated series of impulses, which can force
the mechanical side into motion, freeing stuck wheels with a sticky pivot of dust spec etc.
#64-375010 Elma Dryer
Dryer unit, ideal for clocks and instrument mechanisms.
Fan is almost silent in operation and blows air at a max. temperature of 70º.
After blowing off excess fluids, place movement or instrument on top of dryer unit
Until thoroughly dry. Dimensions: 190 x 180 x 130mm.
#LR-415 L&R Industrial Dryer
The Dryer evenly distributes hot air at a stable temperature.
Small enough to fit on a countertop, The Dryer can be set up anywhere
near a standard 110 Volt AC outlet. Made in USA and built to last.
L&R Dryers are unconditionally guaranteed for one year.
Dimensions: L 2540mm x W 157mm x H 102mm
Heating area 180 sq. cm.
PERRIN
H&W Perrin Co. Ltd.
Toronto, ON
M4H 1N5
www.Perrin.ca
Phone: 416-422-4600
1-800-387-5117
Fax: 416-422-0290
1-800-741-6139
Bergeon Waterproof Testing Equipment
Page 10
#64-5555/98 Bergeon® 6 Atmosphere WaterProof Tester
The advantage of using a water type tester is that when pressure is released
and the watch is plunged into water, bubbles of air exiting the case will pinpoint
where the case is leaking. IE; Crown, case gasket, crystal seal, etc. Watch is
suspended above the water and air pressure is increased using the built-in
manual pump. If the case leaks, the increased air pressure will seep into the
case. Press the air release valve and plunge watch into water. The air, which
leaked into the case under pressure will now exit the case, providing a visual
indicator of the leak source. Tests to 6 atmospheres. (1 atm. = 10 meters)
#64-5555-10 Bergeon 10 Atmosphere WaterProof Tester
A new execution of the original Bergeon 5555 tester. This tester is capable
of pressure testing watches to 10 atmospheres. The manual built-in pump
can be used for testing up to 6 atmospheres. For testing pressures higher
than 6 atmospheres a compressor must be used. The compressor links with
the tester by a nozzle connection on the side of the unit. All other functions
and use methods are the same as 5555/98. New unit has a larger diameter
water cylinder than the original unit for easier handling of larger cases and
features a drop guard that prevents accidental sinking of cases. Removable
cylinder allows for easier draining. (1 atm. = 10 meters)
#64-5402 Bergeon Waterproof Tester (for watches with 2 piece stems)
Specially designed air pressure apparatus to test water tightness of watches with
two piece stems, without the penetration of water. Procedure is simple. Remove the
crown then place the watch on the fan-shaped support, engaging the case tube into
the nylon pump nozzle. Pull the piston as far as it will go and then release. If the
piston moves back towards the pump, then the watch is leaking and will have to be
re-examined. If the piston remains still, place the watch in the water and observe.
If no air bubbles appear, then watch is considered waterproof.
Bergeon Auto-Test and Final -Test
Winder for automatic watches to test the winding function and
mainspring breaking. Holds up to six watches at once. Can be
used horizontally or vertically. Indicates on average, to within
5 seconds, the performance of a watch on the wrist. Replaces
the static control of positions with a lifelike test, as if it was worn
on the wrist.
The Auto-test turns at 4 revolutions per minute.
The Final-test turns at 1 revolution per minute.
#64-5802-110 ........final-test
#64-5803A-110.......auto-test
PERRIN
H&W Perrin Co. Ltd.
Toronto, ON
M4H 1N5
www.Perrin.ca
Phone: 416-422-4600
1-800-387-5117
Fax: 416-422-0290
1-800-741-6139
Horotec® Testing Equipment
Page 11
67-19106 Horotec® "Impulse Detector"
Detects and amplifies the impulses given off by the electronic side of a quartz watch.
The impulses are represented by flashing diodes and an audible beep for each impulse
emitted. Place the non-working watch on the detector if an impulse is shown, then the
problem is mechanical. If no impulse, then the problem is electrical. Check battery, if cell
is dead, replace and repeat test. If the battery is good and no impulse was detected, then
the problem is electrical. This is a basic, fast and easy diagnostic tool. (Operates on 1- 9V battery)
67-19107 Horotec® "Turbo"
Device for unjamming and testing the wheel train of quartz watches. The TURBO emits a
series of high speed impulses which cause the gear train to operate 60 times its usual
speed. Can be used to kick start movements, find defects in the wheel train or to check
that the hands are clearing the dial markers and each other all around the dial etc.
Operates on 1 -9V battery.
#67-19108 Horotec® "FlashTest"
The FLASHTEST is a multi-function portable tester for analog quartz watches and watch
movements. Supplied with 2 precision probes, AC/DC adapter, 9V battery, instructions
for use and a technical guide on movement consumption and coil resistance values
of popular quartz movements. Without opening the watch the FLASHTEST can
perform quick tests on electronic parts such as the battery, electronic circuit,
coil and step motor. It has a turbo feature that can be used to unjam the wheel
train, check that hands are turning free and clear, and check that calendar
functions are operating properly. These tests can quickly determine if a
malfunction is caused by an electronic or mechanical fault. When a watch is
opened the FLASHTEST can perform tests of the real battery status (load test),
consumption of the electronic circuit, consumption of movement and the coil
continuity. Tests performed on the opened watches are necessary to get precise information on the
status of vital components. The extra-large digits give quick and easy readings on the large LCD
panel. The battery test function will test from 0 to 19.999 volts.
#67-19900 Horotec® "Demagnet"
Demagnetizer for small watch parts.
Just place part on the target and push the button.
Operates on one 9V battery.
#67-19903 Horotec® "DemagnetPro"
Bigger more powerful version of the demagnet.
Operate on an AC/DC adapter (included).
Demagnetizes watch and clock parts as well as hand tools.
MTG Testing Equipment
Page 12
#67-19171 Multifunction Timegrapher MTG-1000
The TIME GRAPHER MTG-1000 is a compact model which
measures beat rate, beat error and amplitude of balance.
The gain of the input signal is adjusted automatically, but can
be manually adjusted for movements with very strong or
weak signal. Unit also detects and sets the beat number
(can also be set manually). Detects beats 18,000–19,600–21,600–
25,200–28,800–36,000. Unit has acoustic beat simulation
(can be switched off) Beat error is displayed (240 dots horizontal) on monochrome LCD display.
Supplied with 6 position microphone, manual, external power source.
All settings can be adjusted easily with 3 buttons and the menu line on the top of the display. It is
easy to use and allows a fast and comfortable analysis of the watch movement.
This model features a big, high resolution backlit LCD screen
with 4 different display modes. It measures beat rate, beat
error, beat number and amplitude. It can record up-to 2048
beats and offers a "Pause" and "Shift" function to pause
measuring and view the previous 2048 beats. Furthermore this
unit comes with a programed test mode: The watch can be
tested in up-to 6 positions (positions can be selected). After completion
of the test program the test results are displayed as a test report, which includes beat rate, beat error
and amplitude in each single position. It also shows the maximum difference of the beat rate and
amplitude of the 6 positions.
Supplied with 6 position microphone, manual, dust cover and external power source connection.
Optional printer available.
#67-19172 Multifunction Timegrapher MTG-4000A PRO
The MGT-4000A PRO measures beat rate, beat error, beat
number and amplitude and is equipped with a TYAP signal
processing unit, which offers a very powerful AGC
(automatic gain control) which controls the signal level automatically
and filters side noise. Measurement is highly stable and reliable
(especially the amplitude). It also offers a 7" backlit, color LCD screen
with 5 different displays modes. It can record up-to 720 beats and offers a "Pause" and "Shift"
function to pause measuring and view the previous 720 beats.
This unit comes with a programed test mode: The watch can be tested in up-to 6 positions (positions can
be selected). After completion of the test program the test results are displayed as a test report, which
includes beat rate, beat error and amplitude in each single position. It also shows the maximum
difference of the beat rate and amplitude of the 6 positions.
Supplied with 6 position microphone, manual, dust cover and external power source connection.
Optional printer available.
PERRIN
H&W Perrin Co. Ltd.
Toronto, ON
M4H 1N5
www.Perrin.ca
Phone: 416-422-4600
1-800-387-5117
Fax: 416-422-0290
1-800-741-6139
Page 13
#67-19173 Timegrapher MTG-4000B
The MTG-4000B is a 2 channel model especially for watch
manufacturing, watch traders, and final quality check. It is
possible to measure two watches with the same beat rate at
the same time and show the results simultaneously on the 7"
backlit, color LCD screen. MTG-4000B measures beat rate,
beat error and balance amplitude of up to 2 watches
simultaneously. The gain of the input signal is adjusted automatically, but can be manually adjusted
for movements with very strong or weak signal. Unit also detects and sets the beat number (can also be
set manually). Detects beats 18,000–19,600–21,600–25,200–28,800–36,000. Beat error is tracked
vertically on the screen with 4 different color modes. Displayable diagram height 180 dots.
Supplied with 2 pieces of 6 position microphones, manual, dust cover and external power source
connection.
#67-19174 Timegrapher MTG-4000T
The MTG-4000T is a 3 channel model especially for watch
manufacturing, watch traders, and final quality check. It is
possible to measure three watches with the same beat rate at
the same time and show the results simultaneously on the 7"
backlit, color LCD screen. MTG-4000T measures beat rate,
beat error and balance amplitude of up to 3 watches
simultaneously. The gain of the input signal is adjusted automatically, but can be manually adjusted
for movements with very strong or weak signal. Unit also detects and sets the beat number (can also be
set manually). Detects beats 18,000–19,600–21,600–25,200–28,800–36,000. Beat error is tracked
vertically on the screen with 4 different color modes. Displayable diagram height 180 dots.
Supplied with 3 pieces of 6 position microphones, manual, dust cover and external power source
connection.
Timegrapher MTG-500 is the basic model of the Timegrapher
series. This unit measures beat rate and beat error. It features
simple handling, compact size and an unbeatable price. It is
perfect for the small watch service shops and hobbyists.
As the watch beat is detected automatically, there is nothing to
do but put the watch on the microphone. The MTG-500 timing
machine will start measuring immediately and display the results on the backlit LCD screen. TG-500
is equipped with a 6 position microphone, manual, external power source.
#67-19177 MTG "THERMOPRINT" Thermal Printer
The direct thermal printer "THERMOPRINT" is the perfect accessory for
those who prefer to have their results on paper. It is compatible with the
MTG-3000, MTG-4000A PRO and MTG-5000. It offers the possibility to
print the numeric and/or graphic results of the testing or the numeric and
graphic results of the long term monitoring mode (only MTG-5000)
PERRIN
H&W Perrin Co. Ltd.
Toronto, ON
M4H 1N5
www.Perrin.ca
Phone: 416-422-4600
1-800-387-5117
Fax: 416-422-0290
1-800-741-6139
Page 14
#67-19175 Multifunction Timegrapher MTG-5000 (TCXO and TYAPS)
The MTG-5000 is the state-of-the-art, top model, for
professional use. With a high resolution 7" color TFT display,
the TYAPS signal processing unit, a horizontally divisible
screen, a resolution of 0.2 s/d for rate, a highly stable
temperature compensated TCXO time base and a long term
monitoring function (up to 32 hours) for rate and amplitude.
A horizontally divisible screen which instantly doubles the
length of the display. Testing positions can be set manually or with the optional motorized
microphone. The test sequence can be done automatically in all six positions. The MTG-5000 is the
best equipped to meet all requirements of a professional watch service.
#67-19175B Automic-1 Automatic Motorized Microphone
The automatic stepper motor driven microphone "AUTOMIC-1"
Can be connected and employed to handle the programmed test mode
and the long-term monitoring programs automatically.
Compatible with MTG 4000 and MTG 5000 timing machines
#67-19000 Universal Battery Tester
General use analogue cell tester. Tests 1.5V & 3V watch cells plus
AA – AAA – C – D – N – 9V. Also tests the 12V batteries for lighters
and car remotes. Watch cells can be inserted into the side of the unit
for a quick "push of the button" test. Other types can be tested using
the attached leads. Also features a negative and positive contact spot
on the surface of the tester.
#67-19004 "Renata" Watch Cell Tester & Impulse Detector
Compact and rugged analogue watch cell tester. Tests 1.5V & 3V cells.
Features a built-in impulse detector, which indicates with sound and lights
if the electronic portion of the watch is working and putting out a drive impulse
to the rotor without even opening the watch. Can be used to determine if the
movement is having electronic or mechanical problems.
#67-19105 Battery, Impulse & Coil Tester
Compact analogue tester for watch cells.
-Tests silver oxide (high drain & low drain) plus 3V lithium cells.
-Tests for coil continuity using detachable leads.
-Features a built-in impulse detector.
Greiner-Vibrogaf Testing Equipment
Page 15
Vibrogaf Compact 900 Timing Machine
A universal watch timing machine for measuring time deviation on all types of mechanical and quartz
watches. The results are displayed on a color LCD screen (320 x 240 pixels) Features an integrated
speaker for controlling beat noises. Can be integrated with a PC. Optional printer is available.
#68-89000 Vibrgraf Compact 900 with MP86M Multi-positional
Microphone for Mechanical Watches.
Beat number is automatically detected, beat error, time deviation,
amplitude, escapement noise (graphic). Special programs for the
quick check of pendulum clocks and program for special escapements.
Optional automatic microphone available.
#68-89100 Vibrograf Compact 900 with QM06 Combined Microphone
for Mechanical & Quartz Watches.
The Compact 900 with the QM06 microphone allows timing of mechanical
watches and quartz watches. It has all the functions for mechanical plus
for quartz it gives time deviation, no-load consumption, impulse consumption,
resistance of rotor coil, battery voltage (high & low drain), lower working voltage
limit and EOL.
#68-89500 Vibrograf AM10-2 Automatic Microphone
Motorized automatic microphone for use with Compact 900 timing machine.
This microphone allows the timing machine to proceed through a programed
sequence of positional timing test with the microphone moving itself through
the six positions while the timing machine records the data in each position.
#68-99400 Thermal Printer
Thermal printer is compatible with the Compact 900, Chrono Touch,
Leak Checker Prime and Poseidon LT-100.
Supplied with connecting cable.
#68-64999 Vibrograf "Chrono Touch" Timing Machine with MP12 Microphone
Chrono Touch belongs to the latest generation of watch testers. Simple
operation via a touch screen and a crystal clear, high resolution color display.
Key Features:
-Automatic detection of beat number, rate, amplitude and beat error.
-Measurement time and lift angle can be freely selected.
-Multi-positional microphone.
-Graphic display of beat noise.
-Speaker for listening to watch noise.
-USB/PC interfaces for data transfer and adding software updates.
-Optional thermal printer (#68-99600) available.
PERRIN
H&W Perrin Co. Ltd.
Toronto, ON
M4H 1N5
www.Perrin.ca
Phone: 416-422-4600
1-800-387-5117
Fax: 416-422-0290
1-800-741-6139
Page 16
Negative pressure(vacuum) waterproof Testing
The principle behind the use of negative pressure testing is simple. Watch is placed in the machine
with an accurate measuring gauge making contact with the watch crystal. Negative pressure
(vacuum) is applied.
As the pressure outside the case is lowered, the air inside the case tries to expand.
The gauge detects this by measuring the deformation of the crystal surface.
If a case is waterproof this deformation will increase as more vacuum is applied and stay that way.
If the case leaks there will be no deformation or the deformation will subside as the air
is able to leak out of the case because of an imperfect seal.
#68-66011 Vibrograf "Leak Checker Prime"
The new Leak Checker Prime is the perfect mix of technology and good design.
Able to test for leaks up to -0.7 bar vacuum. It provides everything you would
expect of a modern, easy to use leak testing unit. The unit needs no additional
expensive compressor or vacuum pump.
Features:
-Suitable for all watch types including small ceramic watches.
-Accurate, robust pressure sensor.
-Vacuum created by an internal vacuum pump.
-Testing time can be selected and programmed up to 300 seconds.
-Vacuum can be freely selected and programmed in steps of -0.1 bar to -0.7 bar.
-Intuitive user interface, results displayed on a color 5" TFT capacitive touchscreen (800 x 480 pixels).
-Optional thermal printers (#68-99400 or #68-99500) available for printout of results.
-Enables connection to a network via Ethernet.
#68-11140 Vibrograf "Poseidon LT-100" Waterproof Tester
The intelligent leak tester for watches!
This unit tests waterproofness using negative pressure and/or positive pressure.
The unit will perform a series of tests automaticly, starting with negative pressure.
If the watch passes this test it will proceed testing, using positive pressure (external).
It will perform a series of tests under increasing pressure until it reaches the
maximum pressure of 10 bars or until the watch fails a test at one of the lower
levels of pressure. The machine has 12 test programs which are individually
programmable. Deformation of the watch is measured continuously during
testing, this is done with an accuracy of less than 0.0001µm (micron).
Deformation and pressure levels are constantly monitored and displayed on
the color screen as a numeric or graphic. A certificate of results can be printed using
the optional thermal printer or interfaced PC.
A non-oil type compressor with 10 bar capacity (with or without reservoir) is required. A maintenance
kit is recommended. This should consist of filters (0.01µm) and moisture separator (see #6822010000002) Should damage occur through neglect of this recommendation warranty will be void.
Page 17
#68-11168 Gast 10 Bar Compressor
A non-oil type compressor without reservoir.
Max. capacity 10 bars.
Maintenance free.
#68-22010000002 Maintenance Kit
A micro-filter and moisture separation system with 3 different
connection ports. Installs between the compressor and
Poseidon LT-100 water proof testing machine.
#68-17610 Vibrograf "WPL610" 10 Bar Waterproof Tester.
Water type waterproof tester. This method allows the tester to see where the air is leaking
from the case and determine if it is the case gaskets, crystal or crown which is causing the
leak. Watch is fitted into the machine and suspended above the water, external air pressure
source is activated (compressor required) and chamber is pressurized to a maximum of
10 bar. The 3 position control lever near the pressure gauge controls the tester. Right
position descends the watch into the water as pressure is slowly released. Center position
raises & holds watch above water, left position releases air pressure. As the pressure is
released air bubbles will leak from the case where ever the case seal is compromised.
The exit point of any bubbles is the leak point. Watch is raised out of the water as the
pressure in the chamber is almost equalized. This method prevents chance of water
entering case during test.
#68-96115 Vibrograf "ACS 900" Ultrasonic Watch Cleaning Machine
Fully automated ultrasonic cleaning machine with 4 jars
and drying chamber. Features programmable cycles,
sturdy metal housing and fully enclosed mechanism.
This unit is quiet and smooth running. Supplied with jars
and lids, baskets and dividers, 2 multi-movement holders,
wave breakers and small parts baskets. This machine is
an industry standard and required if you want to service
the watches of many of the high end brand names.
Dimensions: L 425mm x D 425mm x H565mm.
Over 50 optional baskets, dividers and service parts available.
#68-19131 Vibrograf "Drying Apparatus T8"
A warm air drying device with blower fan for watches, watch parts,
watch cases, clock parts, chains, jewellery etc.
Dimensions: W 190mm x D 175mm x H 120mm
115V - 600W
PERRIN
H&W Perrin Co. Ltd.
Toronto, ON
M4H 1N5
www.Perrin.ca
Phone: 416-422-4600
1-800-387-5117
Fax: 416-422-0290
1-800-741-6139
Page 18
#68-11210 Vibrograf "Magnomatic"
Pulse type demagnetizer for watches and small tools. Easy to use, just place
watch or tool in well and push the button. More than 1 pulse may be required
depending on mass and degree of magnetism.
#68-19700 Vibrograf "Antimag AM2" Demagnitizer
Pulse type demagnetizer for watches and small tools. Easy to use, just place
watch or tool in the bulls eye on top of machine and push the button. More
than 1 pulse may be required depending on mass and degree of magnetism.
#68-11215 Vibrograf "Magnotest ll"
Device for detecting and measuring magnetism in items.
Red lights indicate a rating of low, medium or high.
#68-13503-1 GS-50 Greiner Soap Concentrate
A general purpose concentrate cleaning solution for the ultrasonic
in convenient 50ml bottles. Each 50ml bottle make 1 liter of solution.
Need more product info ?
See manufacturer web sites
www.Perrin.ca
www.witschi.com
www.greinervibrograf.com
www.timegrapher.com
www.bergeon.ch
www.elma.com
www.lrultrasonics.com
PERRIN
H&W Perrin Co. Ltd.
Toronto, ON
M4H 1N5
www.Perrin.ca
Phone: 416-422-4600
1-800-387-5117
Fax: 416-422-0290
1-800-741-6139

Watch Testing Equipment

Transcription

Similar documents

HERE - visualjeff.com

PDF - Borrowed Time Watches

Financial Times April 2005

0 - Singapore Management University

Monday – Friday 7p-12m

High Browse May 2003