How To Select A door closer - Top Notch Distributors, Inc.

How to select a door closer
Concealed or surface mounted closers: Door closers are
available in two styles - concealed or surface mounted.
In choosing a closer style for a particular application,
consideration should be given to the type of door being
controlled, frame conditions, aesthetic requirements, and
control features needed. Information contained in the
following material can serve as a guide in selecting the style
and model of closer to meet specific requirements.
If concealed, where?
Closers concealed in the head frame over the door are out
of sight and entirely out of the pedestrians way. They cannot
be harmed by scrub water, cleaning chemicals or floor dirt,
and are protected from airborne contaminant's, like dust.
They are easy to reach for regulation without removing any
parts. Closers for frame sections as thin as 13/4" (44mm) are
available.
Closers located within the door itself are also hidden and
protected. On interior doors of common sizes they do
an excellent job, yet they cost little more than surface
applied closers.
CONCEALED IN FRAME
Where are heavy duty closers required?
Heavy duty closers should always be used in these places:
• Schools or public buildings where hard usage
is expected.
• Exterior doors.
• Doors subject to draft, wind, or air pressure
differential.
• High frequency doors such as those on department
stores, malls, or mixed use tenancies.
Hand of a door?
Some door closers are handed.
When approaching a door from
the push side, if hinged on the
left, it is a left hand door; if
hinged on the right, it is a right
hand door.
For purposes of handing door closers, right hand reverse
bevel and left hand are identical. Also, left hand reverse
bevel and right hand are identical. The hand of the closer
is the same as the hand of the door for all except corner
bracket installations that require a closer handed opposite
the hand of the door.
CONCEALED IN 1 3/4" TUBE
CONCEALED IN DOOR
Surface mounted closers - location?
Closer location is subject to the considerations of
practicality and appearance. Good taste usually decrees
that closers on doors along a corridor be located on the
room side of the door so they are out of the line of sight
from the corridor. Closers should be placed on the inside of
exterior doors for appearance and to shelter them from the
elements.
HINGE (PULL) SIDE MOUNT
Which arm system?
Double lever arm closers can provide control under difficult
conditions for either interior or exterior doors. A parallel
arm system is a type of double lever arm where the main
arm is parallel to the face of the closed door. Functions
available in double lever arm systems are:
REGULAR (REG)
HOLD-OPEN (H)
FUSIBLE LINK
(FL)
CUSH-N-STOP
(CUSH)
HOLD-OPEN
CUSH-N-STOP (HCUSH)
EXTRA DUTY
(EDA)
HOLD-OPEN
EXTRA DUTY (HEDA)
TOP JAMB (PUSH SIDE) MOUNT
PARALLEL ARM (PUSH SIDE) MOUNT
SPRING HOLD-OPEN
CUSH (SHCUSH)
179
SPRING CUSH
(SCUSH)
East – Pennsylvania
Midwest – Missouri
Southwest – Texas
800-233-4210
800-211-4607
866-693-6903
800-722-4210
Fax 800-854-4146
Fax 800-211-4608
Fax 866-693-6904
Fax 800-248-3620
www.topnotchinc.com
West – Nevada
[email protected]
Finishes
LCN closers, pivots, and power operators can be specified in seven
standard or more than 150 custom powder-coated finishes. Powder
coating provides superior protection against the effects of weathering
and provides a durable, chip-resistant finish. For information about
custom finishes, plated finishes and our special rust-inhibiting (SRI)
process, call.
Standard powder-coated finishes
AL (B.H.M.A. 689)
Aluminum
DKBRNZ (B.H.M.A. 695)
Dark bronze
TAN (B.H.M.A. 692)
Tan
STAT (B.H.M.A. 690)
Statuary
LTBRZ (B.H.M.A. 691)
Light bronze
BLACK (B.H.M.A. 693)
Black
BRASS (B.H.M.A. 696)
Brass
Optional SRI
When powder-coated closers are installed in high humidity or
potentially corrosive installations like swimming pools, water treatment
facilities or near large bodies of water, specify LCN SRI Pretreatment.
This optional process extends the corrosion protection offered by
powder-coated finishes.
Custom powder-coated finishes
• 180 custom finishes.
• Durable and chip resistant.
• Superior appearance.
• Corrosion resistant.
• Environmentally friendly process.
• Match doors, frames and hardware.
180
Plated Finishes
U.S. Finish
3
4
9
10
10B
14
15
19
20
26
26D
B.H.M.A. Finish
632
633
637
639
640
645
646
631
649
651
652
Description
Bright brass
Satin brass
Bright bronze
Satin bronze
Satin bronze, oxidized and oil rubbed
Nickel plated, bright (polished brass, nickel plated)
Nickel plated, satin
Satin black (black lacquer)
Bright bronze (oxidized)
Bright chrome
Satin chrome
East – Pennsylvania
Midwest – Missouri
Southwest – Texas
800-233-4210
800-211-4607
866-693-6903
800-722-4210
Fax 800-854-4146
Fax 800-211-4608
Fax 866-693-6904
Fax 800-248-3620
www.topnotchinc.com
West – Nevada
[email protected]
1260 Series
Commercial closer for office buildings, hotels,
manufacturing facilities, retail and other light commericial
uses
The 1260 is an intergral component of a safe, secure and
strong door system. This cast iron closer delivers smooth
closing and a stronger overall door system. The choice of
cylinder sizes, optional arms, installation accessories, and
ease of installation offer a versatile solution to door control
in low to moderate traffic in both interior and exterior.
Top Jamb (Pull Side) Mounting
®
1260 SERIES
The 1260 Series is UL- and ULC-listed for
self-closing doors without hold-open. Tested
and certified under ANSI Standard A156.4,
grade one.
• Size 1-5 closing power.
• Adjustable backcheck.
• Standard 1260 SERIES closer shipped with
regular (non-hold-open) arm, a shaft cover, and self
reaming and tapping screws.
• Sized cylinders for interior doors to
4'6" and exterior doors to 3'6".
• Closer mounts hinge side, top jamb, and parallel arm
on either right- or left-swinging doors.
• 1260 meets ADA requirements.
1260-72
Options:
• 1260-72 non-handed plastic slim line cover.
• 1260-18 drop plate is required for hinge side mount where top rail is
less than 21/2" (64 mm). Also required for top jamb mounting where
head frame is less than 13/4" (44 mm) or flush ceiling condition
exists. Plate requires minimum 11/2" (38 mm) minimum top rail or
11/4” (32 mm ) head frame.
• 1260-18PA drop plate is required for parallel arm mounting where top
rail is less than 43/8" (111 mm), measured from the stop. Plate
requires minimum 13/4" (44 mm) minimum top rail.
1260-18
1260-18PA
• 1260-3077 non-handed arm mounts hinge side or top jamb.
1260-3049
1260-3077
East – Pennsylvania
Midwest – Missouri
Southwest – Texas
800-233-4210
800-211-4607
866-693-6903
800-722-4210
Fax 800-854-4146
Fax 800-211-4608
Fax 866-693-6904
Fax 800-248-3620
www.topnotchinc.com
West – Nevada
[email protected]
181
• 1260-3049 non-handed arm mounts hinge side, top jamb or parallel
arm (62PA required). Hold-open adjustable at shoe.
1460 Series
Surface-mounted closers
Slimline design for narrow head frames and top rails. Cast iron cylinder
for exceptional service life. UL-listed for use on fire-rated doors. Allweather hydraulic fluid eliminates seasonal adjustments. 10-year
warranty.
ADA: Size 1 closer meets 5.0 lbs. opening force requirements on interior
doors.
®
1460/1461 SERIES
• Metal Designer Series or standard cover.
• Mountings: Pull side, top jamb and parallel arm.
• Non-handed, non-sized. Size 1 to 6.
• Interior doors to 5'0", exterior doors to 4'0".
• Fast, accurate installation.
• Delay action (optional) provides additional time for people to move
through the door. 1461 only.
• Spring poser of a 1461 cylinder for exterior doors to 48” (1219 mm) and interior doors to 60” (1524 mm).
Hinge (Pull Side) Mounting
Top Jamb (Push Side) Mounting
Parallel Arm (Push Side) Mounting
Cush Mounting
EDA Mounting
CUSH arms can be templated
for maximum opening/holdopen point at
85°: A = 23/8” (60 mm)
B = 99/16” (243 mm)
90°: A = 15/8” (41 mm)
B = 91/16” (230 mm)
182
100°: A = 5/8” (16 mm)
B = 81/16” (205 mm)
East – Pennsylvania
Midwest – Missouri
Southwest – Texas
800-233-4210
800-211-4607
866-693-6903
800-722-4210
Fax 800-854-4146
Fax 800-211-4608
Fax 866-693-6904
Fax 800-248-3620
www.topnotchinc.com
West – Nevada
[email protected]
1460 Series
Surface-mounted closers
1460 SERIES
1460-62PA
Options:
• 1460-3077 regular non-handed arm mounts side or top jamb.
1460-79LR
• 1460-62PA required for parallel arm mounting.
• 1460-3077L long non-handed arm includes long rod and shoe
1460-79LR for top jamb mount with deep reveal.
• 1460-3049 hold-open non-handed arm mounts hinge side, top
jamb or parallel arm (62PA required). Hold-open adjustable at
shoe.
• 1460-3077EDA Extra duty non-handed parallel arm features
solid forged steel main and forearm for potentially abusive
installations.
• 1460-3077CNS CUSH-N-STOP non-handed parallel arm
features solid forged steel main arm and forearm with stop in
soffit shoe.
1460-3077EDA
• 1460-3049CNS HCUSH non-handed arm, provides hold-open
function with templated stop/hold-open points. Handle controls
hold-open function.
1460-3077CNS
• 1460-72 non-handed plastic slim line cover with feature strip.
• 1460-18 drop plate is required for hinge side mount where top
rail is less than 21/2" (64 mm). Also required for top jamb mounting
where head frame is less than 13/4" (44 mm) or flush ceiling
condition exists. Plate requires minimum 11/2" (38 mm) top rail or
11/4" (32 mm) head frame.
1460-3049CNS
• 1460-18PA drop plate is required parallel arm mounting where
top rail is less than 43/8" (111 mm), measured from the stop. Plate
requires minimum 13/4" (44 mm) top rail.
• 1461-3071 standard, non-handed cast iron cylinder assembly.
1460-18PA
1460-18
183
1461-3071
East – Pennsylvania
Midwest – Missouri
Southwest – Texas
800-233-4210
800-211-4607
866-693-6903
800-722-4210
Fax 800-854-4146
Fax 800-211-4608
Fax 866-693-6904
Fax 800-248-3620
www.topnotchinc.com
West – Nevada
[email protected]
1460 Series
SURFACE-MOUNTED CLOSERS
The 1461T SUPER STOCK® is a slimline, single-lever (track) arm
closer designed for interior use on narrow headframes and top
rails. The modern styling and small projection make it an
excellent choice for interior doors.
®
1461T SERIES
The 1461T SERIES is UL- and ULC-listed for self-closing doors without hold-open. Tested and certified under ANSI Standard
A156.4, grade one.Comes with the following:
• 1461T-72 non-handed plastic slim line cover with feature strip.
• 1461T-3077T non-handed single lever arm mounts hinge side, top jamb, or stop face. Track roller not included with arm.
• 1461T-3038 standard non hold-open, non-handed track mounts on either side of the door. Will accept hold-open clip
and/or bumper assembly.
• 1461T-3034 quiet, low friction track roller assembly. Shoulder dimension “X” = 1/8” (3 mm).
Options:
• 1461-3071 standard, non-handed cast iron cylinder assembly.
Hinge (Pull Side) Mounting
Top Jamb (Pull Side) Mounting
Stop Face (Push Side) Mounting
1461T-3034
1461T-72
1461-3071
1461T-3077T
184
1461T-3038
East – Pennsylvania
Midwest – Missouri
Southwest – Texas
800-233-4210
800-211-4607
866-693-6903
800-722-4210
Fax 800-854-4146
Fax 800-211-4608
Fax 866-693-6904
Fax 800-248-3620
www.topnotchinc.com
West – Nevada
[email protected]
2000 and 5000 Series Concealed
Mounted in Head Frame and
Top Door Rail
®
2014 SERIES
The concealed 2014 Series is a heavy-duty closer designed to
provide complete concealment. The single-lever arm and roller
assembly provide smooth, quiet door control and the choice of
finishes and track functions meet virtually all architectural requirements.
The 2014 SERIES is UL-listed for self-closing doors without
hold-open. Tested and certified under ANSI Standard A156.4.
For interior or exterior doors. Single-acting cylinder in head frame.
Concealed arm and track in door top rail.
• Overhead concealed closer.
• Application-specific closers are designed to provide
optimized door control for a specific mounting.
• Aluminum frame requires minimum 4" x 4" tube.
• Arms: Optional hold-open.
• Handed for right- or left-swinging doors.
The concealed 2034/2035 SERIES Pacer ® is a heavy-duty closer
designed to fit in a narrow 13/4" aluminum transom. The single-lever
arm and roller assembly provide smooth, quiet door control and the
choice of finishes and track functions meet virtually all architectural
requirements.
®
2034/2035 SERIES
The 2034/2035 SERIES is UL-listed for self-closing doors,
without hold-open. Tested and certified under ANSI
Standard A156.4. 2034/2035 SERIES closer using 420 Fire
Shield®, hollow metal frame, and 20-minute labeled wood
door preparation meet; ASTM E-152, UL 10B, UBC 43.2,
and Canadian Standard 4-S-104.
• Overhead concealed closer.
• Application-specific closers are designed to provide
optimized door control for a specific mounting.
• Designed to fit in a narrow 13/4" aluminum transom.
• Arms: Single- and double-acting,
185
optional hold-open.
East – Pennsylvania
Midwest – Missouri
Southwest – Texas
800-233-4210
800-211-4607
866-693-6903
800-722-4210
Fax 800-854-4146
Fax 800-211-4608
Fax 866-693-6904
Fax 800-248-3620
www.topnotchinc.com
West – Nevada
[email protected]
3000 Series Concealed Mounted
in Head Frame and Top Door Rail
The concealed 3133 SERIES is designed to
mount in a 13/4" interior door. The single-lever
arm and roller assembly provides complete
concealment and the choice of finishes and
track functions meet virtually all architectural
requirements.
®
3133 SERIES
The 3133 Series is UL- and ULC-listed
without hold-open for self-closing doors.
Tested and certified under ANSI Standard
A156.4, grade one.
For interior doors.
Single-acting cylinder and standard arm in
top rail of door. Concealed track in head
frame.
• Concealed in-door closer.
• Application-specific closers are designed
to provide optimized door control for a
specific mounting.
• Designed to mount in a 13/4" interior door.
• Handed for right- or left-swinging doors
and sized cylinders.
• Single-acting doors.
• Arms: Optional hold-open track, regular
track with bumper or hold-open track
with bumper.
Opions:
• 3130-3054 hold open clip that mounts in
track to provide hold-open function. Holdopen point controled by clip location.
186
3130-3054
East – Pennsylvania
Midwest – Missouri
Southwest – Texas
800-233-4210
800-211-4607
866-693-6903
800-722-4210
Fax 800-854-4146
Fax 800-211-4608
Fax 866-693-6904
Fax 800-248-3620
www.topnotchinc.com
West – Nevada
[email protected]
4000 Series
®
Heavy-duty, surface-mounted closers
• Heavy-duty cast iron cylinder for exceptional service life.
UL- listed for use on fire-rated doors.
• All-weather hydraulic fluid eliminates seasonal
adjustments.
• 10-year warranty.
ADA: Size 1 closer provides less than
5.0 lbs. opening force on 36" wide door.
4010 EDA Shown
4010/4011/4016 SERIES
Hinge (Pull Side) Mounting
• Interior doors to 5'0".
Exterior doors to 4'0".
• Non-sized cylinder adjustable for interior doors to 4'6" and
exterior doors to 3'6".
• Delay action. 4011 only.
• Tested to over 10 million cycles to reduce
replacement and long-term costs.
• Track version available.
Options:
• 4010-72 standard, non-handed plastic cover.
• 4010-3077 regular non-handed arm.
• 4010-3049 hold-open handed arm provides hold-open
function, adjustable at elbow.
4010-72
• 4010-18 drop plate is required where top rail is less than 33/4"
(95mm). Plate requires minimum 2" (51mm)top rail.
• 4010-11 corner bracket for doors where top jamb or parallel
arm mounted closer can not be used. Allows 180° opening
with regular arm. Projects 5” (127 mm) from stop, 1311/16” (348
mm) from frame. Requires opposite hand closer.
4010-3077
4010-3049
• 4010-16 corner bracket for doors where top jamb or parallel
arm mounted closer can not be used. Allows 125° opening
with regular arm or 100° with hold-open arm. Projects 5”
(127 mm) from stop, 1213/16” (325 mm) from frame. Requires
opposite hand closer.
4010-11
187
4010-18
4010-16
East – Pennsylvania
Midwest – Missouri
Southwest – Texas
800-233-4210
800-211-4607
866-693-6903
800-722-4210
Fax 800-854-4146
Fax 800-211-4608
Fax 866-693-6904
Fax 800-248-3620
www.topnotchinc.com
West – Nevada
[email protected]
4000 Series
Heavy-duty, surface-mounted closers
• Heavy-duty cast iron cylinder for exceptional service life.
UL-listed for use on fire-rated doors.
• All-weather hydraulic fluid eliminates seasonal adjustments.
• 10-year warranty.
ADA: Size 1 closer provides less than 5.0 lbs. opening force on 36” wide
door.
4110 EDA shown
4110/4111 SERIES
Parallel Arm (Push Side) Mounting
• Interior doors to 5’0”.
Exterior doors to 4’0”.
• Non-sized cylinder adjustable for interior doors to 4’6” and exterior
doors to 3’6”.
• Delay action. 4111 only.
• Tested to over 10 million cycles to reduce replacement and longterm costs.
• Advanced variable backcheck.. 4111 only.
• LCN FAST™ Power Adjust, a revolutionary visual indicator for
spring power adjustment. 4111 only.
Options:
• 4110-3077EDA extra duty non-handed parallel arm features
forged, solid steel main and forearm for potentially abusive
installations.
• 4110-3077CNS CUSH-N-STOP handed parallel arm features solid
forged steel main arm and forearm with built-in stop in soffit shoe.
4110-3077EDA
188
4110-3077CNS
East – Pennsylvania
Midwest – Missouri
Southwest – Texas
800-233-4210
800-211-4607
866-693-6903
800-722-4210
Fax 800-854-4146
Fax 800-211-4608
Fax 866-693-6904
Fax 800-248-3620
www.topnotchinc.com
West – Nevada
[email protected]
4000 Series
Heavy-duty, surface-mounted closers
4110-3049CNS
4110/4111 SERIES
Options:
• 4110-3049CNS HOLD-CUSH handed arm provides hold-open function
with templated stop/hold-open points. Handle controls hold-open
function.
4111-SC
• 4111-SC SPRING CUSH non-handed parallel arm for abusive
applications features solid forged steel main arm and forearm with
spring loaded stop in the soffit soffit shoe.
• 4111-HSC SPRING HOLD-CUSH non-handed parallel arm for
abusive applications features solid forged steel main arm and
forearm with spring loaded stop in the soffit shoe. Handle controls
hold-open function.
4111-HSC
• 4110-18 required for push side mount where top rail is less than
51/8” (130 mm), measured from the stop. Plate requires minimum 2”
(51 mm) minimum top rail. Plate also used with CUSH arm
installations.
4110-18
Heavy-duty, SMOOTHEE® closers
• Heavy-duty cast iron cylinder for exceptional
service life. UL-listed for use on fire-rated doors.
• All-weather hydraulic fluid eliminates seasonal
adjustments.
4013T SERIES
• Standard 4010T series closer shipped with
standard arm, standard track, track roller,
standard plastic cover, and self reaming and
tapping screws.
• Interior doors to 4’0”.
• Closer mounts hinge side, specify right or left
swinging door.
189
• Fast, accurate installation.
East – Pennsylvania
Midwest – Missouri
Southwest – Texas
800-233-4210
800-211-4607
866-693-6903
800-722-4210
Fax 800-854-4146
Fax 800-211-4608
Fax 866-693-6904
Fax 800-248-3620
www.topnotchinc.com
West – Nevada
[email protected]
4000 Series
4031 Series
• Application-specific closers are designed to provide optimized
door control for a specific mounting configuration:
• Interior doors to 4'0".
Note: 4031 SERIES is not recommended for use on exterior doors.
Options:
4030 shown
• 4031-3077 regular non-hand arm.
• 4031-3049 hold-open handed arm provides
hold open function, adjustable at elbow.
4031-3049
190
4031-3077
East – Pennsylvania
Midwest – Missouri
Southwest – Texas
800-233-4210
800-211-4607
866-693-6903
800-722-4210
Fax 800-854-4146
Fax 800-211-4608
Fax 866-693-6904
Fax 800-248-3620
www.topnotchinc.com
West – Nevada
[email protected]
4000 Series
The 4040/4041 SUPER SMOOTHEE® is a heavy-duty, double-lever
arm closer designed for institutional and other high traffic applications.
The wide choice of options, installation accessories and ease of installation
offer maximum versatility.
UL- and ULC-listed for self-closing doors without hold-open.
Tested and certified under ANSI Standard A156.4, grade one.
®
4040/4041 SERIES
• Non-handed.
• Interior doors to 5'0".Exterior doors to 4'0".
• Self-reaming, self-tapping screws.
• Fast, accurate installation.
• Delay action.
• Track version available.
Top Jamb (Push Side) Mounting
Parallel Arm (Push Side) Mounting
4040 CUSH Mount
4040 EDA Mount
191
Hinge (Pull Side) Mounting
East – Pennsylvania
Midwest – Missouri
Southwest – Texas
800-233-4210
800-211-4607
866-693-6903
800-722-4210
Fax 800-854-4146
Fax 800-211-4608
Fax 866-693-6904
Fax 800-248-3620
www.topnotchinc.com
West – Nevada
[email protected]
4000 Series
4040/4041 SUPER SMOOTHEE®
4040-3077
Options:
• 4040-3077 regular non-handed arm mounts pull side or top
jamb with shallow reveal. P4041 closer includes PA SHOE
• 4040-3077L long non-handed arm includes long rod and shoe
4040-79LR for top jamb mount.
• 4040-3077ELR extra long non-handed arm includes extra long
rod and shoe, 4040-79ELR for top jamb mount with deep
reveal.
4040-79LR
• 4040-3049 hold-open non-handed arm mounts pull side or top
jamb with shallow reveal, hold-open adjustable shoe. P4041
closer includes 4040-62PA shoe required for parallel arm
mounting.
4040-79ELR
• 4040-3077EDA extra duty non-handed parallel arm features
solid forged solid steel main and forearm for potentially abusive
installations.
• 4040-3049EDA hold-open extra duty handed arm provides
hold-open function, adjustable at the shoe.
• 4040-3077CNS cush-n-stop non-handed parallel arm
features solid forged steel main arm and forearm with stop in
soffit shoe.
4040-3049
• 4040-3049CNS hcush arm, provides hold-open function with
templated stop/hold-open points. Handle controls hold-open
function.
4040-3077EDA
4040-3049EDA
4040-3077CNS
192
4040-3049CNS
East – Pennsylvania
Midwest – Missouri
Southwest – Texas
800-233-4210
800-211-4607
866-693-6903
800-722-4210
Fax 800-854-4146
Fax 800-211-4608
Fax 866-693-6904
Fax 800-248-3620
www.topnotchinc.com
West – Nevada
[email protected]
4000 Series
4040/4041 SUPER SMOOTHEE®
4040-3077SC
Options:
• 4040-3077SC spring cush non-handed parallel arm for abusive
applications features solid forged steel main arm and forearm
with spring loaded stop in the soffit shoe.
• 4040-3049SC spring hcush non-handed parallel arm for abusive
applications features solid forged steel main arm and forearm
with spring loaded stop in the soffit shoe. Handle controls holdopen function.
4040-3049SC
• 4040-72 standard, non-handed plastic cover.
• 4041-3071 standard, non-handed cast iron cylinder assembly.
• 4040-18 drop plate is required for hinge side mount where top rail
is less than 33/4" (95mm). Plate requires minimum 2" (51mm)
minimum top rail.
4040-72
• 4040-18G drop plate locates top jamb mounted closer flush with
top of head frame face in flush ceiling condition. Plate requires 13/4”
(44 mm) minimum head frame.
• 4040-18PA drop plate is required for parallel arm mounting where
top rail is less than 51/2" (140 mm), measured from the stop. Plate
requires minimum 2" (51mm) top rail.
• 4040-18J drop plate centers top jamb mounted closer vertically on
head frame where face is less than 31/2” (89 mm). Plate requires
13/4” (44 mm) minimum head frame.
4041-3071
• 4040-30 cush shoe support provides anchorage for fifth screw
used with cush arms, where reveal is less than 31/16” (78 mm).
• 4040-61 blade stop spacer required to lower parallel arm shoe to
clear 1/2” (13 mm) blade stop.
4040-18G
4040-18PA
4040-18
4040-18J
4040-30
193
4040-61
East – Pennsylvania
Midwest – Missouri
Southwest – Texas
800-233-4210
800-211-4607
866-693-6903
800-722-4210
Fax 800-854-4146
Fax 800-211-4608
Fax 866-693-6904
Fax 800-248-3620
www.topnotchinc.com
West – Nevada
[email protected]
4000 Series
The 4040T SMOOTHEE® is a flexible heavy duty track closer designed
specifically for interior doors in institutional and other rugged high traffic
applications.
The 4111T SMOOTHEE® is a heavy duty track closer designed
specifically for interior doors in institutional and other high traffic
applications.
UL-and ULC-listed for self-closing doors. Tested and certified under
ANSI standard A156.4, grade one.
4040T Series Shown
4040T/4111T SERIES
• Interior doors to 4’0”.
• 4040T closer mounts pull side on door, pull side top jamb or push side on door. 4111T closer mounts stop face side,
specify right or left swinging door.
Hinge (Pull Side) Mounting
Top Jamb (Pull Side) Mounting
Stop Face (Push Side) Mounting
4040T-3038
4040T-3077T
4040T/4111T SERIES comes with:
• 4040T-3077T standard non-handed arm. Arm does not include
track roller.
• 4040T-3038 standard, non hold-open, non-handed track.
4040T-3034
• 4040T-3034 quiet, low friction track roller assembly. Shoulder
dimension “X” = 1/8” (3 mm).
4040T-3054
• 4040T-72 standard, non-handed plastic cover.
• 4110T-72 standard, non-handed plastic cover. 4111T only
194
• 4040T-3054 hold-open clip, mounts in track to provide hold-open
function. Hold-open point controlled by clip location. 4040T only.
4040T-72
4110T-72
East – Pennsylvania
Midwest – Missouri
Southwest – Texas
800-233-4210
800-211-4607
866-693-6903
800-722-4210
Fax 800-854-4146
Fax 800-211-4608
Fax 866-693-6904
Fax 800-248-3620
www.topnotchinc.com
West – Nevada
[email protected]
4000 Series
Fire/life safety closer/holders for fire and
smoke-barrier doors.
Designed to hold doors open in normal use but will release
and automatically close doors under fire conditions.
Heavy-duty cast iron cylinder for exceptional service life.
UL-listed for use on fire-rated doors. Two-year warranty.
4040 SE 1
4040 SE SERIES
The 4040SE SENTRONIC® is a heavy-duty, non-handed,
non-sized closer/holder designed to provide single-point
hold-open for fire and smoke barrier doors. The door is held
open until current interruption releases the holding mechanism
and the door closes. Single-lever (track) arm closer is specifically
designed for interior doors. Choice of finishes, track functions,
and installation accessories meet virtually all life safety
requirements.
Choice of 24 or 120 volt.
The 4640 Auto-Equalizer™ is a smart & reliable electrically powered
low-energy power operator. It provides easy access for people with
disabilities, the elderly, or the frail. Designed primarily for manual
opening applications that occasionally require automatic opening.
The 4640 Series is UL and ULC Listed with regular arm for
self-closing doors and meets the provisions of ANSI standards
A117.1, A156.19.
• Non-sized cylinders for interior doors to 4'6" and
exterior doors to 3'6".
• Non-handed for either right or let swinging door.
• Easily accessible switches provide on/off and continuous
hold-open functions. Control module provides all timing and
sequential door functions, electric strike controls and adjustments
for opening speed and force.
Flush
Ceiling Mount
195
Standard
Mount
East – Pennsylvania
Midwest – Missouri
Southwest – Texas
800-233-4210
800-211-4607
866-693-6903
800-722-4210
Fax 800-854-4146
Fax 800-211-4608
Fax 866-693-6904
Fax 800-248-3620
www.topnotchinc.com
West – Nevada
[email protected]
Magnets
Fire/life safety closer/holder for fire and smoke-barrier doors.
The Sentronic® SEM7800 SERIES are heavy-duty, electrically controlled
door-holding magnets. Magnets are fail safe and hold until the current is
interrupted. A manual door closer is used to control and close the door.
A choice of floor, recessed-wall, or surface-mounted wall magnets are
available.
®
7800 MAGNETS
All 7800 SERIES magnets are UL-listed for smoke- barrier or labeled fire
doors.
• 7800 SERIES magnets are shipped with a screw pack for through
bolt or wood screw attachment of the door- mounted armature.
SEM 7830 Shown
• Available in aluminum or dark bronze finishes.
• Wall units should be mounted 24" (610 mm) to 48" (1219 mm) from
the floor for best performance.
• Suitable for use in pocket installations.
• Three magnet mountings:
Recessed wall mount: SEM 7840, SEM 7850
Surface wall mount: SEM 7830
Surface floor mount: SEM7820
• Choice of 12, 24 or 120 volt.
• Simplified wiring.
196
Finishes:
689, 695.
East – Pennsylvania
Midwest – Missouri
Southwest – Texas
800-233-4210
800-211-4607
866-693-6903
800-722-4210
Fax 800-854-4146
Fax 800-211-4608
Fax 866-693-6904
Fax 800-248-3620
www.topnotchinc.com
West – Nevada
[email protected]