Access Control SystemAccess Control System

Transcription

Access Control System
inženiring d.o.o.
Špruha 19
1236 Trzin
Slovenia
tel.: +386 1 561 07 40
fax: +386 1 561 07 44
www.metra.si
Product Catalogue
Manufacturer:
IOC Trzin, Špruha 19, SI-1236 Trzin, Slovenia
Phone: +386 1 56 10 740
Fax: +386 1 56 10 744
Web: www.metra.si




The contents of this document may be subject to change without any prior notice.
All efforts have been made to ensure the accuracy of the contents of this document at the time of going to
press. However, should any errors be detected, METRA would greatly appreciate being informed of any
such errors.
METRA does not assume any responsibility for any errors herein.
If you require any further information on the listed product(s), see product’s Flyer or contact Metra Sales.
© Copyright 2011 Metra inženiring
All rights reserved.
r.1103
d.o.o.
Metra Access Control Product Catalogue
1. Reception Desk
Desktop POS Reader
ORDER CODE: ELDR*
Desktop POS Reader
Technical specifications:
Power: 12 V DC
Connections: 1 x RS-232 serial, 1 x Metra NET
Network
Note:
Power supply and serial cable included!
Standard models are supplied with mask in gray colour.
ORDER CODES for Desktop POS Reader
1
EL
2
DR
3
IS
SD
LF
LG
MF
4
_XXX
Column 1:
EL ... Supports standard RFID Tickets.
Column 2:
Product Group
DR ... Desktop POS Reader
Column 3:
Reader option
IS
ISO reader 13.56 MHz. Reads all ISO15693 and ISO14443 A/B compatible RFID Tags.
SD
SkiData Reader. Reads all SkiData RFID tickets (125khz as well as 13.56 MHz).
LF
LF Multitag reader. Reads different Low Frequency (125 – 134 kHz) RFID Tags. Hitag 1, Hitag 2, Hitag
S, EM Marin
LG
Legic reader. Reads Legic Prime and Legic Advant 13.56 MHz Tags.
MF Mifare reader. Reads all ISO14443 A/B compatible RFID Tags.
Column 4:
Colour combination
Standard colour combination (supplied with mask in gray colour).
XXX Reserved for additional colour coding. Contact Metra sales for colour options.
See also
USB/Serial converter
On page 17
Page 3
ORDER CODE: DRU*
Desktop POS Reader USB
Power: 5 V DC; Obtained from USB port.
Connections: 1 x USB
ORDER CODES for Desktop POS Reader USB
1
DRU
2
IS
LF
MF
Column 1:
Product Group
DRU ... Desktop POS Reader USB
Column 2:
Reader option
IS
LF
S, EM Marin
ORDER CODE: ELRD*
LCC NET POS Station
Power: 12 VDC
Integrated Metra POS Reader
LCD TFT Touch screen
29 – key special Keypad
Windows XP Embedded OS
Note:
Power supply is included!
Standard models are supplied with POS Reader’s mask
in gray colour. Housing in black colour with front panel
in titanium finish.
ORDER CODES for LCC NET POS Station
1
EL
2
RD
3
IS
SD
LF
LG
MF
4
_XXX
Column 1:
Column 2:
Product Group
RD ... LCC NET POS Station
Page 4
Column 3:
Reader option
IS
SD
LF
S, EM Marin
LG
Column 4:
Colour combination
Standard colour combination (supplied with POS Reader’s mask in gray colour).
See also
LCD Customer Display
On page 17
ORDER CODE: DVIT*
Info Terminal
Power: 12 V DC
Integrated Metra POS Reader
LCD TFT Touch screen
Windows XP Embedded operating system
Note:
Power supply is not included!
Black housing with aluminium front panel in “titanium
grey” anodized finish and black foil.
ORDER CODES for Info Terminal
1
DV
2
IT
3
IS
LF
MF
SD
4
_XXX
Column 1:
Product Group
DV ... Display VGA 10”
Column 2:
Product Version
IT ... Info Terminal
Column 3:
Reader option
IS
LF
S, EM Marin
SD
Page 5
Column 4:
Colour combination
Standard colour combination (supplied with POS Reader’s mask in gray colour).
See also
Wall Mount bracket
On page 17
Holders for “build-in” mounting
On page 17
Power supply: 12 V / 5 A
On page 17
Network Controller
ORDER CODE: NCTCP
Network Controller TCP/IP
Power: 12 V DC
Power supply is included.
Connections: 2 x Power, 2 x Metra NET Network,
1 x RS-232 serial channel, 1 x LAN network, 1 x USB,
1 x Emergency open Push-button input
Note:
Converter between Metra NET Network (CAN) and PC
LAN network (TCP/IP). Can also be connected directly to
the PC over USB or RS-232. Enables communication
between Metra NET devices and Metra NET software.
ORDER CODE: NCNET
Network Controller NET
Power: 230 V AC
Connections: 3 x USB 2.0, 1 x Metra NET Network,
1 x LAN network, 1 x DVI-D, 1 x VGA, 1 x Audio, 1 x
Emergency open Push-button input
Note:
Converter between Metra NET Network (CAN) and PC
LAN network (TCP/IP). It enables communication
between Metra NET devices and Metra NET software.
See also
Emergency Open Push-Button
On page 23
Network Controller / Repeater Mounting Plate for 19’’ rack
On page 23
Page 6
2. Access Control
Door Access Terminal
ORDER CODE: ELDL*S
Door Access Terminal for surface mounting
Power: 12 V DC
Connections: 1 x Metra NET Network, 1 x Relay output
Note:
Standard models are supplied with front mask in gray
colour.
Door Access Terminal for in-wall mounting
ORDER CODE: ELDL*U
Power: 12 V DC
Note:
colour.
ORDER CODES for Door Access Terminal
1
EL
2
DL
3
IS
SD
LF
LG
MF
4
S
U
5
_XXX
Column 1:
Column 2:
Product Group
DL ... Door Access Terminal
Column 3:
Reader option
IS
SD
LF
LF Multitag reader. Reads different Low Frequency (125 – 134 kHz) RFID Tags. Hitag 1, Hitag 2, Hitag S,
EM Marin
LG
Column 4:
Product Version
S
Surface Mounting
U
In-wall Mounting
Page 7
Column 5:
Colour combination
Standard colour combination (supplied with front mask in gray colour).
See also
Extension Relay Module
On page 18
Power Supply
On page 18
Connecting cable for Metra devices
On page 23
Parking Access Terminal
ORDER CODE: ELPT*
Power: 12 V DC
Note:
colour.
Anchor is not included!
ORDER CODES for Parking Access Terminal
1
EL
2
PT
3
IS
SD
LF
LG
MF
4
_XXX
Column 1:
Column 2:
Product Group
PT ... Parking Access Terminal
Column 3:
Reader option
IS
SD
LF
LF Multitag reader. Reads different Low Frequency (125 – 134 kHz) RFID Tags. Hitag 1, Hitag 2, Hitag S,
EM Marin
LG
Column 4:
Colour combination
Standard colour combination (supplied with front mask in gray colour).
Page 8
See also
Power adapter 24 V AC or DC / 12 V DC
On page 18
Fence/PAT anchor
On page 18
Turnstile Access Terminal
ORDER CODE: ELTA*MT
TAT Master with Reader
Power: 24 V DC
Connections: 1 x Metra NET Network, 1 x RS-232
serial, 2 x Relay output
Note:
Standard models are supplied with antenna mask in gray
colour.
Power supply and anchor are not included!
ORDER CODE: ELTA*ST
TAT Slave with Reader
Power: 24 V DC
Connections: 1 x Metra NET Network, 1 x RS-232 serial
Note:
colour.
Anchor is not included!
Power obtained from Master device.
Page 9
ORDER CODE: ELTA*RMT
TAT Master with Wristband Capturer
Power: 24 V DC
Connections: 2 x Metra NET Network, 1 x RS-232
serial, 2 x Relay output
Note:
colour.
Wristband container for collecting captured Wristbands is
included!
Power supply and anchor are not included!
ORDER CODES for Turnstile Access Terminal
1
2
3
4
5
6
7
Stand alone pillar tube
EL
TA
IS
M
T
MF
S
_XXX
Stand alone pillar tube with ticket container and
integrated Wristband Capturer
EL
TA
IS
R
M
T
MF
_XXX
Column 1:
Column 2:
Product Group
TA ... Turnstile Access Terminal
Column 3:
Describes type of the RFID ticket supported.
IS
ISO reader 13.56 MHz. Reads all ISO15693 and ISO14443 A/B compatible RFID Tickets.
MF
Mifare reader. Reads all ISO14443 A/B compatible RFID Tickets.
Column 4:
Describes Ticket Capture option.
R
Wristband Capturer integrated (Master only)
No capturing container.
Column 5:
Describes Turnstile Access Terminal electronics.
M
One direction (Master)
S
Other direction (Slave, combination with master only)
Column 6:
Describes type of housing ticket container/maintenance door orientation.
T
Stand alone stainless steel pillar tube
Column 7:
Colour combination
Standard colour combination (supplied with antenna’s front mask in gray colour)
Page 10
See also
Wristband container
On page 18
Power Supply
On page 19
Anchor 1
On page 19
Anchor 2
On page 19
Connection Cables
On pages 19-20
Tripod Turnstile
If only one reader is specified in order code its default position is left side.
Only one Wristband Capturer can be specified. Default position is left side.
Reader or Wristband Capturer can be easily interchanged or moved from left to right side (or vice versa) on
site.
ORDER CODE: TT*
Configuration: Reader / blank
Power: 24 V DC
Connections: 2 x Metra NET Network,
2 x Push button input
Note:
colour and cover in mat black.
Power supply and anchors are not included!
ORDER CODE: TTR*
Configuration: blank / Wristband Capturer
Power: 24 V DC
Note:
ORDER CODE: TT*
Configuration: Reader / Reader
Power: 24 V DC
Note:
Page 11
ORDER CODE: TT*R*
Configuration: Reader / Wristband Capturer
Power: 24 V DC
Note:
ORDER CODES for Tripod Turnstile
1
TT
2
IS
RIS
MF
RMF
3
IS
MF
-
4
CC
Column 1:
Product Group
TT ... Tripod turnstile
Columns 2 and 3:
Describes the type of the ticket reader for Left and Right side of the Tripod Turnstile
IS
ISO reader 13.56 MHz. Reads all ISO15693 and ISO14443 A/B compatible RFID Tickets.
RIS
Wristband Capturer ISO. Reads and captures Metra ISO 15693 and ISO 14443 A/B Tickets.
MF
Mifare reader. Reads all ISO14443 A/B compatible RFID Tickets.
RMF
Wristband Capturer Mifare. Reads and captures Metra ISO14443A Mifare Tickets.
Empty - no reader, one direction only.
Column 5:
Colour combination
Standard colour combination: Antenna(s) front mask(s) in grey colour and cover in mat black.
Standard
Material: fibreglass
Accessories: none
Finish: mat black
CC
Antenna(s) front mask(s) in grey colour and cover made of carbon fibre.
Carbon
Material: Carbon fibres
Accessories: stainless steel baggage sliding pad
Finish: raw carbon fibre / matte stainless steel
See also
Wristband container
On page 18
Power Supply
On page 20
Anchors
On page 20
Page 12
Spacers
On page 20
Safety Fuse
On page 20
ORDER CODE: SLAUIN
Gates
Connections: 24 V DC signal for el. lock (solenoid)
Note:
Available in different sizes and variants. Contact Metra
sales for details.
Anchors are not included.
See also
Column anchor
On page 21
Fence/PAT anchor
On page 21
Page 13
3. Payment Terminals
ORDER CODE: ELPROR
Portable reader Orderman MAX
Note:
Power supply is included.
Mifare reader. Reads only ISO14443 A/B compatible
RFID Tickets.
See also
Extra Battery with
Mifare Reader
On page 21
Bluetooth portable
printer
On page 21
Paper for
Bluetooth printer
On page 21
Leather case
On page 22
Charging system
On page 22
RF Antenna for Orderman
ORDER CODE: ELPRORAN
Desktop POS Reader
ORDER CODE: ELDR*
Note:
See section “1. Reception Desk” for more details and
order codes.
ORDER CODE: DRU*
Desktop POS Reader
Note:
See section “1. Reception Desk” for more details and
order codes.
Page 14
4. Tickets
ORDER CODE: SCCP*
Clip
Note:
To get most up to date colour and graphic personalization
options, please contact Metra sales!
ORDER CODES for Clip
1
SC
2
CP
3
MF
IS
TI
4
BG
GY
Column 1:
SC ... Standard RFID Ticket
Column 2:
Describes the type of the ticket according to its shape:
CP ... Metra Clip
Column 3:
Describes the type of the ticket data carrier (chip):
IS
I – CODE (ISO 15693) RFID Tag
MF
Mifare Classic S50 (ISO 14443A) RFID Tag
Column 4:
Describes the colour according to Metra scale and other graphic personalization options. See note.
BG Burgundy
GY Grey
ORDER CODE: SCWB*
Wristband
Note:
To get most up to date colour and graphic personalization
options, please contact Metra sales!
ORDER CODES for Wristband
1
SC
2
WB
3
MF
IS
4
BK
BL
GR
GY
OR
RD
YL
Column 1:
SC ... Standard RFID Ticket
Column 2:
Describes the type of the ticket according to its shape:
WB ... Metra Wristband
Page 15
Column 3:
Describes the type of the ticket data carrier (chip):
IS
I – CODE (ISO 15693) RFID Tag
MF
Mifare Classic S50 (ISO 14443A) RFID Tag
Column 4:
Describes the colour according to Metra scale and other graphic personalization options. See note.
BL
Blue
GR Green
GY Grey
OR Orange
RD Red
YL
Yellow
See also
Wristband container
On page 17
ORDER CODE: EX0000*
Card
*Order codes:
Ticket data carrier (chip)
Mifare (MF1550)
ISO (15963)
Note:
White unprinted RFID card.
Page 16
Order code
EX000024
EX000025
5. Accessories
Reception Desk
USB/Serial Converter
ORDER CODE: EX000049
LCD Customer Display for POS Station
ORDER CODE: ELRDCD
Wall mount for Info Terminal
ORDER CODE: ADVWM
Note:
Power supply adapter is included with the wall mount.
Info Terminal is not included with the wall mount!
ORDER CODE: PS1250E / PS1250U
Power Supply for Info Terminal
PS1250E - EU standard 230VAC connector
PS1250U - UK standard 230VAC connector
Input: 100 – 240 VAC / 120 W / 50 – 60 Hz
Output: 12 VDC / 5 A
Input cable length: 1.5 m
Output cable length: 0.9 m
Output connector: 5.5 mm DC connector
Temperature operating range: 0 C up to +70 C
ORDER CODE: ADVBI
Info Terminal holders for “build-in” mounting
Page 17
Access Control
ORDER CODE: EB001165
Wristband Container
TT & TAT
Dimensions (w/h/l) in mm: 32.5/25.5/51
Note:
For storage and for collecting captured wristbands.
Handle for carrying.
Wristbands are not included!
Extension Relay Module for Door Access
Terminal
ORDER CODE: SA000445
DAT
Note:
Includes Extension Relay board and Distribution board with
additional network and power connectors. Used for higher
security to drive electric door strike. Mounted up to 100 m
from the Door Access Terminal on safe side of the door.
Power supply: 12V DC / 2.5A
DAT
Input: 100 – 240 VAC / 28 W / 50 – 60 Hz
Output: 12 VDC / 2.5 A
Output connectors: Insulated ferrules 0.75
Power adapter 24 V AC or DC / 12 V DC
for Parking Access Terminal
ORDER CODE: EU200014
PAT
Note:
Used to obtain power from 24 VAC or 24 VDC powered
Parking barrier.
PAT
Anchor for Parking Access Terminal
Page 18
Power supply: 24 V / 2.5 A
TAT
Input: 100 – 240 VAC / 70 W / 50 – 60 Hz
Output connectors: Insulated ferrules 1.00
Anchor for Turnstile Access Terminal pillar
tube housing with Wristband Capturer
TAT Master – Slave connection cable
ORDER CODE: SM040006
TAT - Skidata Turnstile connection cables
TAT - Gotschlich Vario connection cables
TAT
TAT
TAT
TAT
TAT
Anchor for Turnstile Access Terminal pillar
tube housing
Page 19
TAT - Gotschlich with Logiturn II
connection cables
Power supply: 24 V / 3.2 A
TAT
TAT
TAT - Gotschlich Ikarus connection cables
TT
Input: 100 – 240 VAC / 90 W / 50 – 60 Hz
Output connector: Phoenix MSTB 2,5/ 4-ST-5,08
ORDER CODE: XLTT_ANCH
Anchor spacers for Tripod Turnstile
ORDER CODE: SLTT_SPACE
Safety fuse
TT
TT
TT
Anchors for Tripod Turnstile
Note:
Special “breaking” fuse for the case of panic.
Made out of acrylic glass.
Page 20
Anchors for Gate Column
Gate
Note:
1 anchor is needed per gate.
Anchor for Gate fence
Gate
Note:
Each leg of the gate’s fence needs it own anchor.
Payment terminals
Extra battery with Mifare reader for Orderman
ORDER CODE: ELPRORBT
Bluetooth portable printer for Orderman
ORDER CODE: ELPRORPT
Paper for Bluetooth printer
ORDER CODE: ELPRORPA
Page 21
Leather case for Orderman MAX
ORDER CODE: ELPRORLC
Orderman charging station
ORDER CODE: ELPRORCS
Metra NET Network components
ORDER CODE: ANTS
Network Splitter
Note:
Used as connecting device for network cable by using
standard UTP cable. It can also connect Metra device to the
Metra NET Network.
ORDER CODE: ANTR2
Network Repeater 2
Note:
Used to join two cable segments of the Metra NET Network.
Each cable segment can be up to 1000 metres long.
ORDER CODE: ANTR8
Network Repeater 8
Note:
Used to join up to 8 cable segments of the Metra NET
Network. Each cable segment can be up to 1000 metres
long.
Page 22
Network Controller / Repeater
Mounting Plate for 19’’ rack
ORDER CODE: ANCMP
Note:
Mounting plate for 19’’ computer rack for 2x “Network
Repeater 2”, 1x “Network Repeater 8” and 1x Network
Controller NET or Network Controller TCP/IP. With nine
additional RJ-45 Metra NET Network connectors.
ORDER CODE: ANTT12
Network Terminator 120
Note:
Coloured Black. Used to terminate single cable segment.
Single segment can be up to 1000 metres long and
connected to Network Controller or Network Repeater.
ORDER CODE: ANTT24
Network Terminator 240
Note:
Coloured Blue. Used to terminate dual cable each segment
separately. Dual cable can be each segment up to 400
metres long. Both cable segments join at the Network
Controller or Network Repeater.
ORDER CODE: ANCEPB
Emergency Open Push-Button
Note:
Key protected push-button to initiate emergency opening of
all lockers in installation. Connected to Network Controller
NET on one side and to Metra NET Network on the other.
ORDER CODE: SM0400*
Connecting cable for Metra devices
*Order codes:
Length
3 metres
5 metres
10 metres
Order code
SM040003
SM040005
SM040010
Note:
Cable to connect Metra device to Network Splitter if longer
cable needed (each device comes with own cable 1 or 1.5
metres long).
Only for Metra devices that operate on 12 V DC.
Page 23
6. Network schematic
Page 24

Access Control SystemAccess Control System

Transcription

Similar documents

SCP60

modern designs - Resene Paints

Northern Indiana Commuter Transportation District

`Tyci Tavoli series of tables` product card

How to search in Cause List

McGuffey`s 3rd Reader - Eclectic Education Series

Information and prices

Develop a lifelong love of reading in every student

2013 - RTAMS

2014 - RTAMS