Kannoa Wicker Specs

FRAME & STRUCTURE DETAILS
• 100% Non recycled aluminum frame (1.2mm to 2.3mm Thickness)
• Welded joint frame
• Powder coated frame
• Hand made by master craftsmen
ALL WEATHER WICKER DETAILS
• Kannoa Raucord High Density Polymer (German Technology)
• The Green Choice 100% Recyclable ISO 14001
• Temp resistant +65°C/-35°C
• Over 250 different wicker selections
SUNBRELLA FABRIC DETAILS
• 100% Solution Dyed Acrylic fabric
• High resistance to mildew and atmosphere chemicals
• 303 Hightec fabric guard
• 93% UV resistant
CERTIFICATIONS
• SGS Societe General Surveillance
• Sunbrella fabric meets California 117 flammability regulations
• 98% UV resistant wicker
Distributed by Korson Furniture Design: 7933 Huntington Road, Woodbridge, ON L4H 0S9. T:: 905-850-1530. E: [email protected]
Frame Specs
100% Non Recycled Powder coated frame
kannoa uses 100% non recycled aluminum ranging between 1.2 to
2.2mm thickness.
Hand made by craftsmen metal workers
Welded Joint Frame
TEL:
305-651-9655
FAX: 786-228-8096
[email protected]
www.kannoa.com
Distributed by Korson
Furniture
Design: 7933 Huntington
Road, Woodbridge,
ON L4H 0S9. T:: 905-850-1530.
E: [email protected]
Wicker Specs
Material Properties:
- UV resistant
- Environmentally friendly
- weatherproof
- High tensile strength
- Chemical resistant
- Colourfast
100% Recyclable
Our wicker is a premium synthetic weaving material suitable for all kinds of applications including outdoor and
indoor furniture as well as garden and home accessories.
Material properties
Properties
Value
Units
Test Reference
Density
950
kg/m3
ISO 1183 Method D
Flexural Modulus
1200
MPa
ISO 178
Charpy Impact Strength
12
KJ/m2
ISO 179 Type 1 Notch A
Hardness (Shore D)
65
Melting Point
129
˚C
ISO 3146 Method C
Vicat Softening Point
127
˚C
ISO 306
Brittleness Temperature
<-70
˚C
ISO 974: 2000
Thermall Conductivity
0.48
W/m ˚C
ASTM C177
Specific Heat
2300
J/kg ˚C
ASTM C351
Coefficient of Linear Expansion
63 x 10-6
˚Cˉ1
ASTM D696-91
ISO 868 Type D
This technical document applies to our entire product range. Our materials are produced and supplied in
accordance with high quality standards and suitable for both indoor and outdoor applications.
TEL:
305-651-9655
FAX: 786-228-8096
[email protected]
www.kannoa.com
Distributed by Korson
Furniture
Design: 7933 Huntington
Road, Woodbridge,
ON L4H 0S9. T:: 905-850-1530.
E: [email protected]
Wicker Specs
Physical properties
Properties
Value
Units
Test Reference
Tensile Strength at Yield
> 20
MPa
ISO 527
Elongation at Break
> 600
%
ISO 527
>3500
hours
Weather Resistance:
Artificial Weathering and Aging
Grey scale classification after test
4-5
DIN 53387 (Xenon Arc Radiation)
The grey scale classification was
determined under the D65 standard
light, class 5 is the best and class 1
is the worst
Recommendation
To avoid critical mechanical stress of the material, it is recommended to avoid sharp edged frames and to use
frames and to use frame with minimum corner radii of 2mm.
TEL:
305-651-9655
FAX: 786-228-8096
[email protected]
www.kannoa.com
Distributed by Korson
Furniture
Design: 7933 Huntington
Road, Woodbridge,
ON L4H 0S9. T:: 905-850-1530.
E: [email protected]
Wicker Specs
Profile Description
Dimension
Surface Finish
6mm
Double Ribbed
6mm
Smooth
8mm
Smooth
4.5mm
Single Ribbed
6mm
Single Ribbed
8mm
Single Ribbed
5mm
Smooth
6mm
Smooth
3mm
Smooth
4mm
Smooth
5mm
Smooth
6mm
Smooth
7mm
Smooth
2.5mm
Smooth
2.5mm
Ribbed
2.8mm
Ribbed
3mm
Ribbed
4mm
Ribbed
4.5mm
Ribbed
4.5mm
Twist Ribbed
7/1.4mm
Smooth
14/1mm
Smooth
15/1mm
Smooth
Webbing strip double ribbed
7mm
Double Ribbed
Webbing strip double ribbed
13.4mm
Double Ribbed
7mm
Double Ribbed
18/1mm
Double Ribbed
Double oval ribbed
Peel smooth
Peel Ribbed
Half Round Smooth
Round Smooth
Round Smooth with wire insert
Round fine ribbed
Tri-Round
Webbing strip smooth
Webbing strip micro ribbed
Cross Sectional view
Distributed by Korson
Furniture
Design: 7933 Huntington
Road, Woodbridge,
ON L4H 0S9. T:: 905-850-1530.
E: [email protected]
TEL:
305-651-9655
FAX: 786-228-8096
[email protected]
www.kannoa.com
Cushion Fill
Kannoa cushions are constructed with High Resiliency foam and dacron batting for the perfect balance of
comfort and durability. Our standards are of the highest quality.
Outdoor Foam
Our high resiliency foam is ideal for outdoor use in various climates, providing a cozy feel with a
contemporary look. With the proper maintenance and care our cushions are made for durability.
This foam meets CA Technical Bulletin 117 and NFPA260.
Water Flow
Our fills are made with high density foam inserts wrapped in Dacron which allows quick water flow
and drain through the cushions. This makes it perfect for any outdoor weather, even places of high
humidity. This foam meets CA Technical Bulletin 117 and NFPA260.
Fire Resist
We use fire resistant polyurethane foam to achieve the highest safety and quality standards. Our
cushions are manufactured to constrain combustion and at the same time deliver good comfort.
This foam meets CA Technical Bulletin 117 and NFPA260.
1. FOAM: 36/18 high density (18, 1.8 lbs/cuft) is a medium firmness used on seat cushions.
2. All cushions are wrapped wih Dacron (bonded polyester) wrap for optimum comfort. Dacron is also water
resistant and helps protect the foam core.
3. Foam and Dacron are sealed with a protective cambric or water proof lining.
We also offer reticulated foam for quick dry use for outdoor cushions.
1. Reticulated foam #30 high density with a medium firmness.
2. Reticulated foam #50 high density with a high firmness.
The open cell structure allows water to pass through easily. This drainable property is perfect for areas in which
cushions may get wet. Simply tip the cushion on en and watch the water run out. leave them in the sun for a
few minutes and they’re ready to sit on.
Add Dacron wrap to make your cushions plush and full.
TEL:
305-651-9655
FAX: 786-228-8096
[email protected]
www.kannoa.com
Distributed by Korson
Furniture
Design: 7933 Huntington
Road, Woodbridge,
ON L4H 0S9. T:: 905-850-1530.
E: [email protected]
Aluminum Specs / 6063
Material properties
Physical Data
Property
Value
Units
Density (lb / cu. in.)
0.097
Elastic Modulus
1.00076e+007
lb/in^2
Specific Gravity
2.7
Poissons Ratio
0.33
Melting Point (Deg F)
1150
Shear Modulus
3.74197e+006
Modulus of Elasticity Tension
10
Thermal Expansion Coefficient
2.34e-005
Modulus of Elasticity Torsion
3
Density
0.0975437
lb/in^3
Thermal Conductivity
209
W/m K
Specific Heat
900
J/kg K
Tensile Strength
26832
lb/in^2
Yield Strength
21030.5
lb/in^2
lb/in^2
Material Uses
1.2mm to 2.2mm (Inner Thickness)
Principal Design Features
This is generally considered to be an extrusion alloy that is heat treatable for strengthening.
Applications
Commonly used in the manufacture of furniture, windows, stair rails, and in pipe railing. Commonly used in
architectural extrusions.
Machinability
Machinability is considered to be average for this alloy.
Forming
Forming ability, either hot or cold, is good.
Welding
The alloy is readily welded by all of the conventional methods. Filler rod should be of the same alloy or AL 4043
alloy.
* Data from www.suppliersonline.com
TEL:
305-651-9655
FAX: 786-228-8096
[email protected]
www.kannoa.com
Distributed by Korson
Furniture
Design: 7933 Huntington
Road, Woodbridge,
ON L4H 0S9. T:: 905-850-1530.
E: [email protected]
Aluminum Specs / 6063
Heat Treatment
Solution heat treat at 970 F for 1 hour followed by water quench. This produces T 4 temper. Other tempers are
accomplished by aging.
Forging
Hot forging may be done in the range of 500 F to 950 F.
Hot Working
Hot working, as with forging, may be done at temperatures above 500 F up to maximum of 950 F.
Cold Working
Cold working characteristics are good for all conventional forming methods.
Annealing
Anneal at 775 F for 3 hours and use controlled cooling at rate of 50 F per hour down to 500 F. Then air cool.
Aging
Aging is done at a temperature of 350 F for 8 hours for T 6 and T 62 tempers. Age at 360 F for 3 hours to get
T5 temper.
Tempering
Not applicable.
Hardening
Hardens due to aging heat treatment and cold working. See "Aging".
Other Physical Props
Electrical conductivity 50% of copper.
Other Mechanical Props
Shear strength for various tempers is: O temper 10, ksi . T 5 temper 17 ksi. T 83 temper 22 ksi
* Data from www.suppliersonline.com
TEL:
305-651-9655
FAX: 786-228-8096
[email protected]
www.kannoa.com
Distributed by Korson
Furniture
Design: 7933 Huntington
Road, Woodbridge,
ON L4H 0S9. T:: 905-850-1530.
E: [email protected]
Plastic Gliders
Our glides are made from Medium-density
clear Polycarbon plastic for great resistance.
Material properties
It can withstand temperatures of 80 °C continuously
The Glides are made in clear finish
Our Glides are made to protect all floor surfaces from scratches
Flexible ribs allow this part to fit any tube thickness from 14 thru 20 gauge.
Easy to replace
Distributed by Korson
Furniture
Design: 7933 Huntington
Road, Woodbridge,
ON L4H 0S9. T:: 905-850-1530.
E: [email protected]
TEL:
305-651-9655
FAX: 786-228-8096
[email protected]
www.kannoa.com