0310-Karndean Training-FINAL2.ai

Transcription

®
The Leading Molding Brand in North America
Coordinating Moldings
for
Coordinating Moldings Brochure
Table of Contents
2
3
Technical Information: SlimTrim
4
Technical Information: Moisture Proof Quarter Round & VersaEdge Extra Tall
5
Shipping/Lead Time: Flat Rate & Free Shipping Policy
6
Shipping/Lead Time: Transit Time
7
Quantities
8
Price List
9
How To Order
10
Warranty
11
Installation: SlimTrim as a Reducer
13
Installation: SlimTrim as a Transition
15
Installation: SlimTrim as an End Cap
17
Installation: SlimTrim with Optional Dowels
21
Installation: SlimTrim on Concrete
22
Installation: VersaEdge Extra Tall
24
Installation: Moisture Proof Quarter Round
1
for Luxury Vinyl Tile & Plank
SlimTrim
VersaEdge Extra Tall
Functions as a Reducer,
T-Molding, & End Cap
Stair Nose
Moisture Proof
Quarter Round
Track, Shim, Shrink Wrap,
& Label Included
®
2
Technical Information
SlimTrim
2”
SlimTrim
1/4”
Functions as a Reducer, T-Molding, & End Cap.
Surface Material: High Wear Resistant Aluminum Oxide Laminate
Core Material: PVC
13/64”
LVT SOLUTION
Reducer:
Transition:
End Cap:
Up to 1/8” (3mm) 1/8-1/4” (3-6mm)
Up to 1/8” (3mm) 1/8-1/4” (3-6mm)
1/8-1/4” (3-6mm)
Sub Floor SlimTrack
Carpet Tap Down Trim
Shim
OPTIONAL DOWEL INSTALLATION
NOTE: Optional Dowel Installation does not work on radiant heat floors.
Reducer:
Up to 3/4”
Glue to
Non-Floating
Surface
Transition:
Up to 3/4”
Dowel
(Sold Separately)
All moldings are 94” long (7’ 10”)
Hard Surface to Carpet
We Recommend
Using a Carpet
Tap Down Trim
When Installing
SlimTrim on
Carpet
Carpet Tap
Down Trim
3
Technical Information
Moisture Proof Quarter Round & VersaEdge Extra Tall
Moisture Proof Quarter Round
Quarter Rounds are used to conceal the required expansion space between the wall
and the vinyl/LVT flooring.
Surface Material: Decorative Paper
3/4”
Core Material: Exterior Grade Composite Wood Product
3/4”
2”
The VersaEdge Stair Nose combines style and function to enhance the beauty of a
staircase or step. For use on flooring with an overall thickness of up to 0.75” (19 mm).
Surface Material: High Wear Resistant Aluminum Oxide Laminate
Core Material: Aluminum
“LOCK-DOWN” INSTALL
(e.g. Stair Treads)
1.5”
“FLOATING” INSTALL
Used where floating of the floor is not required, as with Stair Tread or Glued-Down/Nailed-Down floors.
This can be used on floating floors where expansion and contraction will occur on the opposite side of the flooring plane.
Vinyl/LVT
Alternative Flush
Vinyl/LVT
Adhesive Tape
DO NOT REMOVE BACKING!
Glue
Stair Riser
Detail
Flooring Planks
Must Be Glued!
All moldings are 94” long (7’ 10”)
0.375”
1” Piece of Flooring
Nailed & Glued Down
4
Shipping/Lead Time
Flat Rate & Free Shipping Policy
NH
VT
WA
ME
ND
MT
MN
OR
MA
WI
SD
ID
IL
CO
KS
MO
NJ
OH
IN
KY
WV VA
OK
NM
MD
SC
AR
MS
TX
DE
NC
TN
AZ
CT
PA
IA
NE
NV
UT
RI
MI
WY
CA
NY
AL
GA
LA
FL
Shipping West
Shipping East
(Includes WA, MT, OR, ID, WY, CO, UT, NV, CA,
AZ and NM)
(Includes ME, NH, VT, MA, NY, RI, CT, NJ, DE,
MD, PA, OH, MI, IN, WV, VA, NC, KY, IL, WI, SC,
GA, FL, AL, TN, MS, LA, AR, MO, IA, MN, ND, SD,
NE, KS, OK and TX)
3” Tube ............. $20.00
6” Tube ............. $40.00
*Free Shipping for Orders
3” Tube ............. $15.00
6” Tube ............. $30.00
*Free Shipping for Orders
$150.00 and up
$75.00 and up
Note all COD shipments will have additional COD charges added to them depending on the freight carrier. Please contact your Versatrim customer service department for shipping charges for
Hawaii, Alaska and any location outside the United States of America.
*Free shipping policy is for flooring companies and applies to Standard Pricing orders only. Alaska and Hawaii are excluded from this offer.
5
Shipping/Lead Time
Transit Time
NH
WA
VT
MT
ME
ND
OR
MN
ID
WY
SD
CO
CA
KS
OK
NM
MO
KY
NJ
WV VA
DE
MD
NC
SC
AR
MS
TX
CT
OH
IN
TN
AZ
RI
PA
IA
IL
UT
NY
MI
NE
NV
MA
WI
AL
GA
LA
FL
AK
HI
PR
6 Days
5 Days
4 Days
3 Days
2 Days
1 Day
*Transit times listed above reflect standard business days which does not include Saturday or Sunday. Saturday delivery may be available upon request at an additional cost.
The above lead times are for UPS Ground Shipments. LTL Shipments with trucking companies have a similar transit time, for exact transit times please contact your Versatrim sales representative. .
At your request we can also provide you with guaranteed rush shipments. Please inquire with your Versatrim sales representative.
6
Quantities
PER TUBE
Pieces per 3” Tube
Pieces per 6” Tube
Minimum Pieces
to Order
SlimTrim with Track & Shims
7
32
1
SlimTrim with Dowels
8
34
1
8
40
1
12
50
1
Pieces per Box
Boxes per Pallet
Minimum Pieces
to Order
SlimTrim with Track & Shims
5
187
1
SlimTrim with Dowels
5
187
1
10
187
1
10
187
1
Product
— Standard UPS Charges apply to all UPS Shipments
— Any order over 150 lbs or three 50 lbs tubes will be shipped via Best Common LTL Carrier
PER BOX (Pallets Only)
Product
* All Program ‘C’ Volume Orders must be in box quantities to qualify for volume pricing.
No Minimums to Order
* All Volume orders are subject to freight charges.
7
Pricing (MAF-D) (FOB Henderson, NC)
Pricing Effective February 2015
Standard
Finish
Slim Trim
US - $24.59
(Includes track shim,
shrink wrap, & label)
VersaEdge
Extra Tall
US - $29.71
Moisture Proof
Quarter Round
US - $7.67
Dowel Tree
Optional Use with Slim Trim for
flooring over 6mm up to 3/4”
US - $1.61
Per Tree of 8 Dowels
All moldings are 94 inches long.
1 Piece minimum.
Terms:
- Our standard terms are Net 30 days.
- Customers whose credit cannot be approved or who choose not to have an open account have the option of paying by credit card, sending in a certified check, or COD (collect on delivery).
- Credit applications are under the “How To Order” tab on the Versatrim Website.
This is a custom product and will be non-returnable.
8
How To Order
TO PLACE AN ORDER WITH VERSATRIM:
1. Fill out the following forms to establish your account:
Credit Application (We also accept all major credit cards and certified checks in the event
that you choose not to have an open account with us.)
Company Contact Form. This form will enable us to correctly identify your company, to
expedite your orders and avoid mistakes.
2. Placing your order:
• Easy online ordering at versatrim.com
1. Click ONLINE ORDERING tab at top corner of versatrim.com
2. Select My Account at top menu to register or sign in if you already have an online account with Versatrim
3. Click Create Account at the left and fill out your information or sign in to your existing account at the right
4. Browse the Karndean Color Collection, add items to your shopping cart and follow checkout instructions
• Fax (252.430.8801) or email ([email protected]) your Purchase Order from your system
• Call our order desk at 1.866.200.8132
3. Use your Karndean SKU Number to order coordinating moldings
4. Return Policy:
This is a custom product and will be non-returnable.
®
1.866.200.8132
9
Warranty
Versatrim
®
warrantees the following products
• LVT Transitions
• SlimTrim (SLT)
• Versaedge Tall (VEX)
• Moisture Proof Quarter Round
to the original purchaser against wear out for a period of
• Residential: Limited lifetime
• Light Commercial: 5 years
What is covered and for how long?
For light commercial installations (example: common areas in multi-unit dwellings and low-traffic retail shops) the product is warranted to be free from manufacturing defects for 5 years from
the date of purchase. If a defect covered by this warranty is reported to Versatrim in writing within 5 years of purchase, Versatrim will supply new material of the same or similar grade sufficient
to repair or replace the defective material.
Providing the material was installed and maintained properly, and used as intended and recommended.
Wear out is defined as a complete removal of pattern and/or color from normal traffic and maintenance.
In the event wear out occurs within specified product warranty time frame of the date of purchase, Versatrim provide replacement materials only.
This warranty does not include the following:
1. Damage due to: stains, burns, cuts, gouges, scuffs, scratches, indentations, and other accidents or abuse;
2. Damage caused by vacuum cleaner beater bar, Floor cleaning machines, caster wheels, and cutting from sharp objects.
3. Discoloration or bond release from hydrostatic pressure or excessive moisture/heat caused by such things as flooding, plumbing, appliance leaks;
4. Installation where material was not installed according to Versatrim's specifications and recommended usage;
5. Dissatisfaction due to improper installation, maintenance or irregularities;
6. Reductions in gloss or build up of residue due to improper maintenance or normal wear and gloss reduction/scratches from use.
7. Minor color, shade or texture variations between samples or printed color photography and the actual material.
8. Installation-related errors or damage including improper conditioning of jobsite and flooring materials, including construction damage after installation
9. Damage caused by abuse such as moving appliances or heavy objects across the moldings without adequate protection.
WE EXCLUDE AND WILL NOT BE LIABLE FOR OR PAY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES UNDER OUR WARRANTIES. By this we mean any loss, expense, or damage other than
to the molding itself that may result from a defect in the flooring. Our limited warranties constitute the only express warranties for the product purchased.
• This limited product warranty does not cover the installation of the product
Y•
AR
E
TI M
•W
860 Commerce Drive, Henderson, NC 27537
Fax: 252.430.8801
Email: [email protected]
D LIFE
TE
LIMI
®
RANT
10
Slim Trim Installation
SlimTrim as a REDUCER
Up to 1/8” (3 mm) Floors
Use SlimTrack (Metal Track) for up to 4 mm floors.
*If the flooring manufacturer suggests/permits the use
of underlayments, you may need to shim the track to
accommodate the increase in overall thickness
Step 1
3/8“
Install the flooring plank*. Then place the SlimTrack 3/8”
from the floor and screw it to the sub-floor using
#4x3/4" screws.
Sub Floor
IMPORTANT: Rock SlimTrim back & forth to make sure
it is sitting inside the track BEFORE hammering in!
SlimTrack
SlimTrim
This end of the SlimTrim MUST be placed
on the lower of the two surfaces.
Rubber
Mallet
SlimTrack
If SlimTrim wiggles back and forth, it is
NOT set in the track properly and will
be damaged when hammered in!
Step 2
Line the SlimTrim molding up with the SlimTrack and fit
one end into the molding. Using a rubber mallet, tap the
molding until it engages with the track. Use your hand to
guide the molding into the track as you work your way down,
tapping it in, similar to how you would close a zip-loc bag.
Step 3
Next, go up and down the molding several times, tapping the
Slim Trim all the way into the track. You can use a little more
force once you are sure it is properly engaged in the track.
11
Slim Trim Installation
SlimTrim as a REDUCER
Use SlimTrack & Versatrack Shim for 5-6 mm floors.
Use the same molding & track, just add Versatrack Shim.
1/8 to 1/4” (3-6 mm) Floors
3/8“
Step 1
Sub Floor
Install the flooring plank. Then place the SlimTrack and shim
3/8” from the floor and screw them to the sub-floor using
#4x5/8" screws.
Shim
SlimTrack
SlimTrim
Rubber
Mallet
SlimTrack
Step 2
Step 3
force once you are sure it is properly engaged in the track. 29
12
SlimTrim Installation
SlimTrim as a TRANSITION (T-MOLDING)
*If the flooring manufacturer suggests/permits the use
of underlayments, you may need to shim the track to
accommodate the increase in overall thickness
1”
Install the flooring planks* by leaving a 1" inch (25mm) gap
for the installation of the SlimTrim. Center the SlimTrack
between the two floors and screw it to the sub floor by
using #4x3/4" screws.
Sub Floor
SlimTrack
SlimTrim
Step 1
Rubber
Mallet
SlimTrack
Step 2
Step 3
13
SlimTrim as a TRANSITION (T-MOLDING)
1”
1/8 to 1/4” (3-6 mm) Floors
Step 1
Install the flooring planks by leaving a 1" inch (25mm) gap for
the installation of the SlimTrim. Center the SlimTrack and
Shim between the two floors and screw them to the s
ub floor by using #4x5/8" screws.
Sub Floor
SlimTrack
SlimTrim
Rubber
Mallet
Shim
SlimTrack
Step 2
Step 3
3
14
SlimTrim as a END CAP
NOTE: Carpet Tap Down trim must be
no less than 1/8” from top of track.
Use shim as guide, then remove it.
3/4”
Sub Floor
1”
Carpet Tap
Down Trim
SlimTrack
SlimTrim
This end MUST
be placed on
the lower
surface
Rubber Mallet
*If the flooring manufacturer suggests/permits
the use of underlayments, you may need
to shim the track to accommodate the
Step 1
increase in overall thickness
Install the flooring plank* and carpet (using a carpet tap down
trim) by leaving a 1" inch (25mm) gap for the installation of the
SlimTrim. Position the track 3/4” from where the of the Tap
Down trim meets the carpet and screw it to the sub floor by
using #4x5/8" screws. The carpet tap down trim must be no
less than 1/8” from top of track. Use shim to make track and
tap down trim even, then remove shim.
Step 2
Line the SlimTrim up with the track and fit one end into the
molding. Using a rubber mallet, tap the molding until it engages
with the track. Use your hand to guide the molding into the
track as you work your way down, tapping it in, similar to
how you would close a zip-loc bag.
Step 3
SlimTrim all the way into the track. You can use a little more
15
SlimTrim as a END CAP
NOTE: Carpet Tap Down trim must
be even with the top of the track.
Sub Floor
1”
Step 1
Carpet Tap
Down Trim
SlimTrack
SlimTrim
1/8 to 1/4” (3-6 mm) Floors
Rubber Mallet
Install the flooring plank and carpet (using a carpet tap down
trim) by leaving a 1" inch (25mm) gap for the installation of the
SlimTrim. Position the track 3/4” from where the of the Tap
Down trim meets the carpet and screw them to the sub floor
by using #4x5/8" screws. The carpet tap down trim must be
even with the top of the track.
Step 2
Line the SlimTrim up with the track and fit one end into the
molding. Using a rubber mallet, tap the molding until it engages
with the track. Use your hand to guide the molding into the
track as you work your way down, tapping it in, similar to
how you would close a zip-loc bag.
This end MUST
be placed on
the lower
surface
Step 3
SlimTrim all the way into the track. You can use a little more
force once you are sure it is properly engaged in the track. 4
16
Installation on flooring over 6mm up to 3/4”
OPTIONAL DOWEL INSTALLATION - Part 1
Roughen up surface that
comes in contact with glue
NOTE: SlimTrim Dowels are sold separately. Please
contact your Sales Representative to order.
Step 1
Turn the Slim Trim over and use a sanding sponge, metal
brush or 60 grit sandpaper to roughen up the surface to
increase the bond on the side where glue will be applied.
Step 2
Side View of
SlimTrim
Molding
Each dowel tree (sold separately), contains 8 dowels.
Carefully cut or break dowels off of tree. Slide one dowel
into molding groove and position in center of molding.
Insert additional dowels from both ends. Space dowels
11.5”apart and 1.5” from ends.
Center
one dowel
1.5”
11.5”
1.5”
11.5”
NOTE: Dowels have to fit tightly for
the molding to function properly. If
you find the dowel is too difficult to
slide in, take 100/120 grit sandpaper,
lay it flat on a surface and sand
down the dowel head slightly with a
couple of passes.
17
Flooring
1”
1”
Pencil marks
Step 3
1/4”
Install the flooring planks, including the underlayment, by
leaving a 1" inch (25mm) gap for the installation of the molding
Draw a line on the flooring for the placement of the holes.
Using a 1/4” drill bit, pre-drill holes into the flooring 2” deep.
Be sure to use the same measurements as the dowels,
keeping the holes 11.5“ apart. With a pencil, mark on the floor
where each dowel is located (You will need these for Step 7).
Pencil marks should be about 1” from the pre-drilled holes.
Sub Floor
2”
NOTE: Be sure to vacuum pre-drilled holes.
Pencil marks
Flooring
Step 4
Sub Floor
1”
Carefully line up dowels with pre-drilled holes. Make
adjustments to the dowel positions on the molding
if needed.
18
Side View of Hand Positions
Push down directly
over dowel 1/4”
at a time
NOTE: Do not try to push the entire molding in all at once
by just pressing it in from top! This will bend the dowels.
Flooring
Step 5
First pass (1/4”)
Sub Floor
Second Pass (1/4”)
Third Pass (1/4”)
Forth Pass (1/4”)
Using both hands, start at one end and gently push molding
1/4”down. Make sure dowel is straight and that you apply
pressure directly over dowel. The best position is to hold dowel
with pointer and middle fingers and push down with thumbs.
Moving down the molding again, push the dowels in the floor
1/4” at a time. It should take several passes to push the
molding all the way down.
19
Flooring
PUR-Glue
adhesive
About 3/8” (9.5mm)
Step 6
First pass (1/4”)
Sub Floor
Third Pass (1/4”)
NOTE: Make sure you apply adhesive to ONLY 1 side
of the molding and that all surfaces that the adhesive
touches is dust and debris free.
Forth Pass (1/4”)
Fifth Pass (1/4”)
Flooring
Once molding is about a finger’s width from the floor (about
3/8” or 9.5 mm), insert the tip of a glue gun under 1 edge
of the molding. Apply Liquid Nails or any polyurethane
constructive adhesive along 1 side of the flooring.
Pencil marks
Step 7
Sub Floor
When finished applying adhesive, start again at the beginning
of the molding and push dowels all the way in until molding is
secure. Once molding is in place, use a rubber mallet to tap on
the top of each dowel. Use the pencil marks to reference
where each dowel is located.
20
OPTIONAL DOWEL INSTALLATION: Installation for use on CONCRETE
1”
Flooring
Pencil
marks
1”
2”
Installation on flooring over 6mm up to 3/4”
Install flooring planks, leaving 1 inch gap for molding installation. Draw line on flooring for hole placement. Using a 1/4” concrete drill bit pre-drill 2” deep holes using same
measurements as dowels. With pencil, mark on floor the location of each dowel. BE SURE TO VACUUM PRE-DRILLED HOLES.
1/4”
Concrete
Distance Measurement
Dowel Cutting Template
2
3/4”
5/8”
Cut Here
Cut Here
1/8”
3
NO CUT
Cut Here
is located to the right of
Installation Instructions
3/4”
5/8”
NO CUT
Cut Here
1/4”
1/8”
Carefully cut or break dowels from Dowel Tree.
Use the Dowel Cutting Template to the right to find
your measurement on the template and lay your
dowel over the number that matches your distance
measurement.
With dowel on template, use a utility knife to cut
dowel as indicated on Dowel Cutting Template.
Repeat with all dowels that are to be used.
Cut Here
Concrete
Lay a flat object over flooring and measure from
the concrete at the center between the flooring up
to the bottom of your object. This will give you the
distance to use on the Dowel Cutting Template to
the right.
Take Measurement Here
FOR CONCRETE ONLY!
1/4”
Drill bit
1
Flat object
3/4”
5/8”
1/2”
3/8”
1/4”
1/8”
SURFACE PREPARATION
4
Roughen up surface
that comes in contact
with glue
NO CUT
Cut Here
Cut Here
Cut Here
Cut Here
Cut Here
Clean floor and molding as directed below:
CLEANING PREPARATION FOR BOTH SURFACES
Preparing the floor & molding as outlined is mandatory to achieve the required bonding strength
5
1. Use a damp cloth (water only) to clean both surfaces of loose particles or surface films.
2. Roughen the surfaces with sandpaper (100-150 grit), sanding sponge or metal brush. For flooring, only roughen up area that will be covered (1.25” to 1.5”).
Flooring
Painter’s
Tape to
protect rest
of flooring
3. Degrease both surfaces to remove all traces of oil, grease, dust, and fingerprints by using a solvent such as methyl ethyl ketone (MEK), acetone or isopropyl alcohol.
4. Let both surfaces dry thoroughly before applying adhesive.
comes in contact
with glue
Slide dowels into groove on bottom of the SlimTrim molding and position them according to template. Line up dowels with
pre-drilled holes. Adjust dowels as needed.
NOTE: Dowels have to fit tightly for the molding to function properly. If you find the dowel is too difficult to slide in, take
100/120 grit sandpaper, lay it flat on a surface and sand down the dowel head slightly with a couple of passes (See Detail
A at the right).
6
DETAIL A
Using both hands, start at one end and gently push molding 1/4” down at a time. It should take several passes to push molding all the way down. Best hand
position is holding dowel between pointer fingers and pushing down with thumbs directly over dowel. DO NOT TRY TO PUSH ENTIRE MOLDING IN ALL AT
ONCE.
7
First Pass (1/4”)
Next Passes (1/4”)
When molding is a finger’s width from the floor, insert tip of glue gun under one edge of molding and apply a polyurethane construction adhesive along one side
of the flooring. MAKE SURE YOU APPLY ADHESIVE TO ONLY ONE SIDE OF THE MOLDING AND THAT ALL SURFACES THAT THE ADHESIVE TOUCHES IS DUST
AND DEBRIS FREE.
About
3/8” PUR-Glue
(9.5mm) adhesive
8
Pencil marks
9
When finished applying adhesive, start again at beginning of molding and push dowels all the way down until molding is secure. Use a rubber mallet to gently
tap on top of each dowel until molding sits flush. Use pencil marks as reference.
21
VersaEdge Extra Tall Installation
Versa Edge - Part 1
Installation on flooring with an overall thickness of up to 19 mm (0.75”).
Flooring
Step 1
Install the riser flush to the stair. Clean flooring and molding
as directed below:
CLEANING PREPARATION FOR BOTH SURFACES
Stair Riser
Sub Floor
Release Paper
VersaEdge Surface
Roughened up with
Sanding Sponge or
Sandpaper
Adhesive Tape
Preparing the floor and molding will significantly increase the quality of the bond.
1. Use a damp cloth (water only) to clean both surfaces of
loose particles or surface films.
2. Roughen the surfaces with sandpaper (100-150 grit),
sanding sponge or metal brush. For flooring, only
roughen up area that will be covered (1.25” to 1.5”).
3. Degrease both surfaces to remove all traces of oil,
Painter’s
Flooring
grease and fingerprints by using a solvent such as
Tape to
methyl ethyl ketone (MEK), acetone or isopropyl
protect rest
of flooring
alcohol.
4. Let both surfaces dry thoroughly before applying
adhesive.
comes in contact
with glue
Step 2
Turn VersaEdge over and roughen the inside surface of the
VersaEdge to increase bond by means of 60 grit sandpaper,
sanding sponge, or a metal brush. Then, gently peel the
release paper all the way off the adhesive tape.
Step 3
Caulk Gun
Adhesive
Adhesive Tape
Next, apply a generous bead of a
Premium Polyurethane Construction
Adhesive along the entire inside corner.
Be sure to overlap the tape with
the adhesive.
Underside of molding generously
covered with adhesive
22
VersaEdge Extra Tall Installation
Versa Edge - Part 2
Installation on flooring with an overall thickness of up to 19 mm (0.75”).
Step 4
Stair Riser
Bottom of
Stair Nose
Adhesive Tape
Touch the bottom of molding to the stair riser and carefully
roll the stair nose in place. Make any final adjustments
before you push the molding all the way down. Once it’s
in the final position, press down firmly with your hands and
make your way down the entire stair nose. It may take 2 or
3 passes to set it firmly in place.
Flooring
Adhesive
Step 5
Sub Floor
For Low Traffic, let the adhesive cure for at least 1 hour
before walking on it. For Heavy Traffic, wait 24 to 48 hours.
Stair Riser
NOTE: Complete cure takes 48 hours.
23
Moisture Proof Quarter Round Installation
Moisture Proof Quarter Round - With a Wall Base
Wall
Apply one thin bead of adhesive to the back of the
Quarter Round and attach it to the wall base
molding and support it with a heavy object until
the adhesive has cured so it won’t pop off the
wall base molding.
Vinyl/LVT Flooring
adhesive
Step 1
Sub Floor
Wall
Optional Step: Use finish nails in the wall base
molding every 16” and also through the Quarter
Round and into the wall base molding. Be sure
to pre-drill all holes. Finish up the nails with a color
matching Color Fill.
Finish Nails
Vinyl/LVT Flooring
Step 2
Sub Floor
24
Moisture Proof Quarter Round Installation
Moisture Proof Quarter Round - Without a Wall Base
Wall
Apply one thin bead of adhesive to the back of the
Quarter Round and attach it to the wall and support
it with a heavy object until the adhesive has cured so it
won’t pop off the wall.
Vinyl/LVT Flooring
adhesive
Step 1
Sub Floor
Wall
Optional Step: Use finish nails every 16” through the
Quarter Round and into the wall. Be sure to pre-drill
all holes. Finish up the nails with a color matching
Color Fill.
Finish Nail
Vinyl/LVT Flooring
Step 2
Sub Floor
25
For Additional Installation Instructions & Videos, Go to:
installationadvice.com
®
860 Commerce Drive
Henderson, NC 27537 USA
Phone: 1.866.200.8132
Fax: 252.430.8801
www.versatrim.com

0310-Karndean Training-FINAL2.ai

Transcription

Similar documents

Introduction - MVP Plastics

Flex Series

Atlantis Energy Systems Inc.

deumidificatore comfee

azendi jewellers

Teragren Floor care guide 2013 web.indd

Free In-Home Estimate Call today to schedule Your appointment

Leeds Utd

Mikrotech® Mikrotech