RTS Pocket Programming Guide

Transcription

Radio Technology Somfy ®
Pocket
Programming Guide
Table of Contents
P. 1 How Does RTS Work?
P. 2 Identify RTS Control Options
Transmitters
P. 4 DecoFlex Wireless Wall Switch
P. 5 DecoFlex Table Top Accessory
P. 6 Telis Hand-Held Remote
P. 7 Telis Soliris Hand-Held Remote
P. 8 Telis Modulis Hand-Held Remote
P. 9 Telis 16 Channel Hand-Held Remote
P. 10 Telis 1 Chronis RTS Hand-Held Remote
Repeater
P. 11 RTS Repeater
Receivers
P. 12 Outdoor Lighting Receiver
P. 13 Outdoor Universal Receiver
Interfaces
P. 14 Universal RTS Interface (URTSI)
P. 15 myLink™
Sensors
P. 16 Sunis Indoor WireFree™ Sensor
P. 16 Thermo Sunis Indoor WireFree™ Sensor
P. 17 Eolis 3D WireFree™ Wind Sensor
P. 18 Ondeis WireFree™ RTS Rain & Sun Sensor
Understanding Control Options
P. 20/21 Individual Control
P. 22/23 Group Control
P. 24/25 Individual & Group Control
P. 26 Product Application & Motor
Compatibility Chart
RTS Motor Range
P. 28
P. 28
P. 28
P. 28
P. 29
P. 29
P. 29
P. 30
P. 30
P. 30
P. 31
P. 31
P. 31
P. 32
P. 32
CL32 Cord Lift WireFree™
CT32 Cord Lift WireFree™
Tilt WireFree™
LT30 Roll Up WireFree™
ST30 Sonesse® 30
ST40 Sonesse® 40
Altus 40
ST50 Sonesse® 50
Altus 50
LT50 RTS CMO
Sunea® RTS CMO
Oximo™ RTS
Altus 60
Glydea® 35
Glydea® 60
Quick Programming Guides
P. 34-39 CL32 Cord Lift WireFree™
ST30 Sonesse® 30
ST40 Sonesse® 40
Altus 40
ST50 Sonesse® 50
Altus 50
Altus 60
P. 40-45 Tilt WireFree™
P. 46-49 LT RTS CMO
P. 50-53 Sunea® RTS CMO
P. 54-56 Oximo™ RTS
P. 57-60 Glydea®
Outdoor Lighting Receiver RTS
P. 61
Outdoor Universal Receiver RTS
P. 62
RTS Repeater
P. 63
Universal RTS Interface (URTSI)
P. 63
P. 64-68 myLink™
P. 69-72 Sunis Indoor WireFree™ Sensor
P. 73-78 Thermo Sunis Indoor WireFree™ Sensor
P. 79-80 Eolis 3D WireFree™ Wind Sensor
P. 81-85 Ondeis WireFree™ RTS Rain & Sun Sensor
P. 86-87 Telis 16 RTS
P. 88-93 Telis 1 Chronis RTS
P. 94 Troubleshooting
Home Motion by Somfy
We’ve developed a brand expression that emphasizes the
centerpiece of consumers’ lives, the home. It also represents
Somfy’s mission, bringing homes to life by creating movement
for all openings and allowing consumers to enjoy life’s daily
pleasures for a better quality of life.
How Does It Work?
Simply press a button on a remote control or wall switch
and window coverings move with ease. There is no need
to point or aim the transmitter at the covering because
Radio Technology Somfy® (RTS) is omni-directional.
And just like a garage door opener, the radio waves travel
through walls.
Available with hand-held remotes, wireless wall switches, table
top controls, timers and a convenient app.
No need to aim the control at the motorized window covering, the
radio signal travels through walls similar to a garage door opener
Offers a range of 65 ft. for easy operation
No extra wires are needed
Provides the ability to control all motorized window coverings
individually and/or as a group with one control
Flexibility to change user preferences with simplified programming
Available in single and multi-channel versions
Over 10 million installations worldwide
Secure operation with a rolling code reducing interference with
other radio products
Offers simplified integration with home automation systems
1
Identify RTS Control Options
Transmitters
Hand-Held Remotes
Users can control motorized window coverings by pressing a button
or rolling a scroll wheel on a variety of hand-held RTS remotes.
Wireless Wall Switches
Users can easily control their motorized window coverings when
entering or exiting a room with DecoFlex WireFree™ RTS Wall Switches.
Table Top Remotes
Users can control their motorized window coverings with the versatile
DecoFlex WireFree™ RTS Table Top Accessory remote.
Receivers
Users can adjust window coverings powered by standard motors, as
well as operate incandescent and halogen lights and other outdoor
devices by using a particular receiver.
Interfaces
Users can convert Infrared, RS232, RS485 and WiFi protocol into RTS,
allowing for 3rd party control of motorized window coverings.
Repeater
Users can extend the range of motorized window covering control.
Sensors
Users can set sensors to automatically adjust motorized window
coverings in accordance to the amount of sunlight received,
temperature recorded, as well as the speed and direction of wind.
2
Control
Options
3
DecoFlex WireFree™ RTS Wall Switch
Features
Programming
Button
(recessed)
5 Channel Button DecoFlex WireFree™
RTS Wall Switch shown in White Finish
Also available in multiple finishes and various channel button versions:
Ivory
Black
Almond
Custom engraved buttons available.
4
DecoFlex WireFree™ RTS Table Top Accessory
Features
Easily personalize your control with
custom engraved button names.
LED for each
channel. Available
in 1, 2, 3, 4 and 5
channel versions.
Channel Buttons can be
labeled for easy organization.
(custom engraving also available).
“STOP” button stops the
window covering when
it’s in motion. When
the window covering is
stationary, the “STOP”
button brings it to the
programmed favorite
position.
Programming Button
(recessed)
UP AND DOWN
Command Buttons
DecoFlex WireFree™
RTS Table Top Accessory
Control shown in Silver Finish
Ergonomically designed for comfortable
hand-held use.
Features rubber non-slip feet.
Side view
Also available in black & white finishes:
5
Telis RTS Hand-Held Remote
Features
UP Button
The “my” button acts as a
stop button when the window
covering is in motion. When the
window covering is stationary,
the “my” button brings it to the
programmed favorite position.
DOWN Button
Channel LED
All 4 lights will illuminate
when fifth channel is activated.
Channel Selector Button
Telis 4 RTS
Hand-Held Remote
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Also available in multiple finishes:
Silver
6
Lounge
Patio
shown in Pure finish
Telis 1 RTS also available
Programming
Button
(recessed)
Back view of Remote
Telis Soliris RTS Hand-Held Remote
Features
UP Button
The “my” button acts as a
stop button when the awning
is in motion. When the window
covering is stationary, the
“my” button brings it to the
programmed favorite position.
DOWN Button
When left LED is lit the window
covering will only react to wind
control. When right LED is lit the
window covering will react to
both sun and wind control.
Telis Soliris RTS
Hand-Held Remote
Telis 4 Soliris RTS also available
Patio option
available also:
Programming
Button
(recessed)
Back view of Remote
7
Telis RTS Modulis Hand-Held Remote
Features
Open/Close buttons
Scroll wheel for
incremental tilt control
of horizontal blinds and
sheer horizontal products.
”my” button for a
favorite blind position
LED identifies active channel
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Telis 4 Modulis RTS
Hand-Held Remote
Telis 1 Modulis RTS also available
Programming
Button
(recessed)
Back view of Remote
8
Telis 16 Channel RTS Hand-Held Remote
Features
Signal Indicator
On-Screen LCD Display
Channel Number
16 channels can be used to control 16
individual motorized applications or 16
groups of motorized applications.
Product Icon
A choice of 3 icons is available to visually
represent the product(s) assigned to that
channel.
Product Name
(up to 8 characters: 7 Letters + 1 Number)
Selection Button
Channel Navigation Buttons
UP Button
Favorite position “my” Button
The “my” button acts as a stop button when
the window covering is in motion. When the
window covering is stationary, the “my” button
brings it to the programmed favorite position.
DOWN Button
NOTE: The Telis 16 channel
remote features an LCD screen
that numerically displays
what channel is selected.
Telis 16 Channel RTS
Hand-Held Remote
Programming Button
(recessed)
Also available in Silver finish
Back view of Remote
9
Telis Chronis 1 RTS Hand-Held Remote
Features
Vacation Mode (Only displayed when function is activated.
Varies scheduled time to simulate a lived in look.)
On-Screen LCD Display
Current Time
Programmed Days -2 possible schedules:
Daily schedule - same cycle everyday.
Weekday & weekend schedule - 2 UP & DOWN
times (1 for weekdays & 1 for weekends)
Low Battery Indicator (notifies when
batteries need replacing)
Time Slots
Confirm Selection Button
Channel Navigation Buttons
UP Button
Favorite position “my” Button
The “my” button acts as a stop button when
the window covering is in motion. When the
window covering is stationary, the “my” button
brings it to the programmed favorite position.
DOWN Button
Telis Chronis 1 RTS
Hand-Held Remote
#1805237
Programming
Button
(recessed)
Also available in Silver finish
#1805238
10
Back view of Remote
RTS Repeater
Features
Antenna
The RTS Repeater receives the signal from a
Telis RTS remote or DecoFlex WireFree™ RTS wall
switch or similar device and re-transmits the
signal to an RTS compatible motor or receiver
to extend the RTS range.
Indicator Light
Simply plugs into any 120V AC
electrical outlet.
No programming required.
Should be placed approximately halfway
between the transmitting device such as a
Telis hand-held remote and the receiving
device, the motor.
Solves the challenge of transmitting the signal
in particularly large rooms or areas.
Range: 60 ft.
11
Features
*For programming instructions please go to P. 60
Control patio or deck lights with the same remote used for the awning.
Controls incandescent, halogen lights or any outdoor device up to 500W.
Fully compatible with the Telis RTS range of transmitters and the DecoFlex™
WireFree™ RTS wall switches.
Weatherproof cover with watertight
strain-relief fittings for wires
SEQUENTIAL CONTROL BUTTON
PROGRAMMING BUTTON
GROUND
PROGRAMMING LED
500W Max
Lighting Output
NEUT
HOT
NEUT
HOT
LAMP
500 WATTS MAX.
GROUND
NEUTRAL
HOT
12
Outdoor Universal RTS Receiver
Features
*For programming instructions please go to P. 59
Provides RTS capability to Somfy’s standard motors.
Can be used as a stand-alone RTS control or with RTS sensors.
Two user-defined intermediate positions can be programmed.
Weatherproof cover with watertight
strain-relief fittings for wires
PROGRAMMING BUTTON
GROUND
PROGRAMMING LED
UP
DOWN
MTR COM
MOTOR
NEUT
HOT
NEUT
R
HOT
GROUND
NEUTRAL
HOT
13
Features
Antenna
9 Volt DC
(power supply
included)
IR Sensor Port
RS485
Expansion
RS232
or RS485 Input
Allows user to convert infrared, RS232 and RS485
protocol into Radio Technology Somfy® (RTS) to allow
for third party control.
Offers 16 channels.
Compatible with full range of RTS motors.
With its compact and sleek design, the
URSTI can be housed in a discrete location.
UP
STOP
DOWN
Program Button
Channel Selector
RTS Transmission LED
14
Somfy myLinkTM
Features
TM
The Somfy myLink offers convenient control of any Radio Technology
Somfy RTS motorized application with a smartphone or tablet. It
consists of a simple plug-in device and free app that transforms the
experience that users have with there motorized applications.
LED Indicator States 1. Solid Red: setup mode (out of the box)
a. Re-engage by pressing programming button
on the side
2. Solid Green: connected to LAN
3. Slow Blinking Green: searching for network
4. Quick Red Flash: sending RTS command
5. Solid Amber: failsafe mode
LED Indicator Light
App Status Indicator White O: mobile device can connect
to the myLink(s) and commands are
being sent over the local wifi network.
White O with Sight: mobile device
can connect to the myLink(s) and
commands are being sent over the
internet.
White O with !: the mobile device
cannot connect to a myLink/myLinks.
15
Sunis & Thermo Sunis Indoor
WireFree™ RTS Sensors
Sunis Features - Front view with cover removed
LED Indicator
ON/OFF Selector Switch
Control Setting Panel
window sill mount
Programming Button
Mode Button
Sun Sensitivity
Threshold Adjustment
window mount
The Sunis Indoor Sensor can be programmed to automatically adjust window
coverings in accordance to sunlight threshold settings.
Thermo Sunis Features -
Front view with cover removed
Temperature LED Indicator
Sun & Temperature
Sensitivity Threshold
Adjustment
Sunlight LED Indicator
Mode Button
Programming
Button
Control Setting Panel
Front view with cover removed
Function
Selection Switch
The Thermo Sunis Sensor can be programmed to automatically adjust window
coverings in accordance to sunlight and/or room temperature threshold settings.
Light
sensing
eye
Front view with
cover installed
Suction cup
for mounting
on window sill
or window
16
Back View
Eolis 3D WireFree™ RTS Wind Sensor
Features
Installed discreetly on the end of the front bar.
Easy wireless installation.
Automatically retracts the awning with the detection
of wind generated movements.
Easy to program.
Maintenance free, long life batteries.
Programming
Button
Sensitivity
Adjustment
Button
Mounting
Plate
Also available in multiple finishes:
Ivory
Black
17
Ondeis WireFree™ RTS Rain and Sun Sensor
Features
Combination rain and sun sensor
Control one channel of Radio Technology
Somfy® motorized products
Solar powered rechargeable battery
Adjustable rain and sun thresholds
Wireless installation with flexible mounting
options
Six available modes of operation:
Awning Rain (default)
Awning Sun (requires Telis Soliris
Transmitter)
Awning Rain & Sun (requires Telis Soliris
Transmitter)
Shutter/Screen Rain
Shutter/Screen Rain & Sun
Shutter/Screen Rain & Auto Up
Demo mode for testing configurations
2 easy-to-read LED indicator lights
Sun Sensor
LED
Sun Threshold
Dial
Mounting Plate
Optical Rain
Sensor
Sun Sensor
Rain Sensor
LED
Hatch
Rain Threshold
Dial
Configuration
Switches
Demo Button
Solar Charging Panel
Switch Sticker
Programming
Button
18
Understanding
Control Options
19
Understanding Control Options:
Applies to all Telis RTS
Hand-Held remotes.
Channel 1:
Individual
Control of
SHADE 1
Channel 2:
Individual
Control of
SHADE 2
Channel 3:
Individual
Control of
SHADE 3
Telis 4 RTS
Hand-Held Remote
*Fifth channel is
activated when all
4 LEDs illuminate
Channel 4:
Individual
Control of
SHADE 4
*Channel 5:
Individual
Control of
DRAPERY
The Telis 16 channel remote features an LCD screen
that numerically displays which channel is selected
and provides the option to name each channel.
20
Individual Control
DecoFlex WireFree™ RTS
5 Channel Button Version
21
Applies to all Telis
Hand-Held remotes.
Channel 1:
Group Control
of window
coverings in
FOYER
Channel 2:
Group Control
of blinds in
BEDROOM
Channel 3:
Group Control
of window
coverings
in OFFICE
Channel 4:
Group Control
of window
coverings in
KITCHEN
Telis 4 Modulis RTS
Hand-Held Remote
*Channel 5:
Group Control
of window
coverings in
LIVINGROOM
*Fifth channel is
activated when all
4 LEDs illuminate
22
The Telis 16 channel remote features an
LCD screen that numerically displays which
channel is selected and provides the
option to name each channel.
Group Control
DecoFlex WireFree™
RTS Table Top Accessory
23
Applies to all Telis RTS
Hand-Held remotes.
Channel 1:
Individual Control
of shade in
SHADE 1
Channel 2:
Individual Control
of shade in
SHADE 2
Channel 3:
Group Control
of blinds in
BATHROOM
Channel 4:
Group Control
of shades in
OFFICE
Telis 4 RTS
Hand-Held Remote
*Channel 5:
Group Control
of ALL motorized
shades
*Fifth channel is
activated when all
4 LEDs illuminate
The Telis 16 channel remote features an
LCD screen that numerically displays
which channel is selected and provides
the option to name each channel.
24
Individual and Group Control
DecoFlex WireFree™ RTS
5 Channel Button Version
25
Product Application &
ROLLER SHADE
12 V
Cl32 & CT32
CORD LIFT WIREFREE™
12 V
TILT
WIREFREE™
12 V
LT30
ROLL UP WIREFREE™
24 V
ST30
SONESSE 30
®
110 V
ST40
SONESSE 40
®
110 V
ALTUS 40
110 V
ST50
SONESSE 50
®
110 V
ALTUS 50
110 V
110 V
LT50
RTS CMO
SUNEA
RTS CMO
110 V
ALTUS 60
110 V
110 V
GLYDEA
35 & 35e
®
GLYDEA
60 & 60e
®
26
ROMAN/WOVEN
SHADE
2” HORIZONTAL
BLIND
SHEER
HORIZONTAL
SHADE
P
P
PP
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
Motor Compatibility Chart
PLEATED/
CELLULAR SHADES
AWNINGS
ROLLING
SHUTTER
P
EXTERIOR
SOLAR SCREENS
MOTOR
DETAILS PAGE
DRAPERIES
P.27
P.27
P.27
P
P
P
P
P
P.28
Using CTS40
P.28
P.28
P.29
P
P
P
P
P
P
P
P
P
P
P
P
P.29
P.29
P.30
P.30
P.30
P.30
27
RTS Motor Range
CL 32 CORD LIFT WIREFREE™ - BATTERY OR TRANSFORMER POWERED
31.2mm
23.1mm
12 VDC
Side View
PLEATED/
CELLULAR SHADES
CT32 CORD LIFT WIREFREE™ - BATTERY OR TRANSFORMER POWERED
31.2mm
23.1mm
12 VDC
ROMAN/WOVEN
SHADE
Side View
PLEATED/
CELLULAR SHADES
TILT WIREFREE™ - BATTERY OR TRANSFORMER POWERED
31.5mm
12 VDC
ROMAN/WOVEN
SHADE
50mm
2” HORIZONTAL
BLIND
Side View
12 VDC
LT30 ROLL UP WIREFREE™ RTS - BATTERY OR TRANSFORMER POWERED
30mm motor diameter
Side View
ROLLER SHADE
28
ROMAN/WOVEN
SHADE
SHEER HORIZONTAL
SHADE
*Please note: If you cannot identify the motor or control being
used, please contact Somfy customer service at 877-22SOMFY
24 VDC
ST30 SONESSE® 30 RTS - TRANSFORMER OR LOW VOLTAGE HARDWIRE
Side View
ROLLER SHADE
110 VAC
30mm motor diameter
ROMAN/WOVEN
SHADE
2” HORIZONTAL
SHADE
SHEER HORIZONTAL
SHADE
PLEATED/
CELLULAR SHADES
ST40 - SONESSE® 40 RTS - HARDWIRED OR PLUG-IN
Side View
ROLLER SHADE
110 VAC
ROMAN/WOVEN
SHADE
2” HORIZONTAL
SHADE
SHEER HORIZONTAL
SHADE
PLEATED/
CELLULAR SHADES
ALTUS 40 - HARDWIRED OR PLUG-IN
Side View
AWNING
40mm motor diameter
40mm motor diameter
ROLLING
SHUTTER
2” HORIZONTAL
BLIND
ROMAN/WOVEN
SHADE
EXTERIOR
SOLAR SCREENS
ROLLER SHADE
29
RTS Motor Range
110 VAC
ST50 SONESSE® 50 RTS - HARDWIRED OR PLUG-IN
Side View
50mm motor diameter
ROLLER SHADE
110 VAC
AWNING
50mm motor diameter
ROLLING
SHUTTER
2” HORIZONTAL
BLIND
ROMAN/WOVEN
SHADE
EXTERIOR
SOLAR SCREENS
LT50 RTS CMO - HARDWIRED OR PLUG-IN
Side View
50mm motor diameter
AWNING
30
2” HORIZONTAL
SHADE
Side View
110 VAC
ROMAN/WOVEN
SHADE
ROLLING
SHUTTER
EXTERIOR
SOLAR SCREENS
ROLLER SHADE
*Please note: If you cannot identify the motor or control being
used, please contact Somfy customer service at 877-22SOMFY
110 VAC
SUNEA™ - HARDWIRED OR PLUG-IN
50mm motor diameter
Side View
AWNING
110 VAC
OXIMO - HARDWIRED OR PLUG-IN
Side View
50mm motor diameter
AWNING
110 VAC
EXTERIOR
SOLAR SCREENS
ROLLING
SHUTTER
Side View
60mm motor diameter
AWNING
ROLLING
SHUTTER
31
RTS Motor Range
110 VAC
GLYDEA® 35e RTS - PLUG-IN
53mm
95mm
Bottom View
DRAPERY
110 VAC
GLYDEA® 60e RTS - PLUG-IN
53mm
95mm
Bottom View
DRAPERY
32
QUICK PROGRAMMING
GUIDES FOR
MOTORS AND CONTROLS
P. 32-37 CL32 Cord Lift WireFree™
ST30 Sonesse® 30
ST40 Sonesse® 40
Altus 40
ST50 Sonesse® 50
Altus 50
Altus 60
P. 38-43 Tilt WireFree™
P. 44-47 LT RTS CMO
P. 48-51 Sunea® RTS CMO
P. 52-54 Oximo™ RTS
P. 55-58 Glydea®
Outdoor Universal Receiver RTS
P. 59
P. 60
RTS Repeater
P. 61
P. 61
P. 62-66 myLink™
P. 67-70 Sunis Indoor WireFree™ Sensor
P. 71-76 Thermo Sunis Indoor WireFree™ Sensor
P. 77-78 Eolis 3D WireFree™ Wind Sensor
Ondeis WireFree RTS Rain and Sun Sensor
P. 79-80 Telis 16 RTS
P. 81-86 Telis 1 Chronis RTS
Trouble Shooting Guide
P. 87
33
QUICK PROGRAMMING GUIDE FOR THE FOLLOWING RTS MOTORS
CL
Cl32 CORD LIFT WIREFREE™
®
ST30 SONESSE 30
CT32 CORD LIFT WIREFREE™
®
ST40 SONESSE 40
ALTUS 50
ALTUS 40
LT30 ROLL UP WIREFREE™
®
ST50 SONESSE 50
ALTUS 60
FACTORY MODE
BEFORE YOU BEGIN
Motors are shipped in FACTORY MODE without limit settings and transmitter
Id’s. Power must ONLY be connected to current window covering being
programmed. All other window coverings must be disconnected from their
respective power while programming.
!
Note - If motor is 120V AC hardwired and cannot be disconnected, please
contact an electrician prior to calling Somfy customer service for assistance.
Connect Power To Motor
With the motor installed in window covering, connect power to the
motor (120V AC, or 12V DC or 24V DC transformer or 12V battery wand).
PROGRAMMING MODE
!
While programming, window covering should not be inactive for
longer than 2 minutes or motor will exit PROGRAMMING MODE.
Initiate Programming
On the transmitter, press and hold both the UP
and DOWN
simultaneously until the window covering jogs. A jog is a brief up and
down or in and out motion. In PROGRAMMING MODE, the window
covering will move only when the
UP or DOWN
is held (or
momentary fashion).
34
QUICK PROGRAMMING GUIDE FOR RTS MOTORS
Check the Direction of operation
If hand-held transmitter direction is not properly programmed,
Eolis/Soliris RTS sensor will not function in the manner it was intended.
Damage to motorized window covering and injury may occur as a result.
During installation, it is mandatory to test and verify the motorized
window covering operates in accordance to the commands from
hand-held transmitter.
Installer or user must verify the following Hand-Held
transmitter (DOWN) command:
Awning Installations:
= awning moves outward or extends.
Shade/Shutter Installations:
= shade/shutter moves downward
or closes.
Check Directions
Press and hold UP
or DOWN
. When pressing DOWN
product
should go down or out. If window covering does not correspond with
UP
or DOWN
you must REVERSE the output direction. To reverse
output direction, simply press & hold the my (STOP) until the window
covering jogs. Output direction should now correspond.
Setting Limits
Set the Upper Limit
STEP 1: Bring the window covering to desired UPPER limit stop point with the
UP
button. Press and hold both my (STOP) and DOWN
simultaneously
until the application starts to move, then release. If the window covering
stops when the buttons are released, take it back to the UPPER limit and
repeat. Stop the motor when desired LOWER limit is reached. You can
adjust by pressing UP
or DOWN
after stopping the motor.
Set the Lower Limit
STEP 2: Press and hold both my (STOP) and UP
simultaneously until the
application starts to move, then release. The window covering will stop at
the UPPER limit that was previously set.
!
In case of problems with setting of limits during PROGRAMMING MODE,
turn the power off to the motor for 2 seconds and then back on to reset
the motor. Please return to PROGRAMMING MODE to initiate programming
process.
Confirm Limit Settings
STEP 3: Press and hold my (STOP) until the window covering jogs to confirm
the limit settings. A jog is a brief up and down motion.
35
Programming Completed
Step 4: Press and hold the PROGRAMMING BUTTON on the back of the
transmitter until the window covering jogs. The window covering is
now in USER MODE. In USER MODE, the window covering will operate
by briefly pressing the UP
or DOWN
(or maintained fashion).
USER MODE
Adjusting the Limits in User Mode
To Change the Lower Limit:
STEP 1: Press DOWN
to send the window covering to its current
LOWER Limit.
STEP 2: Press and hold both UP
and DOWN
simultaneously
until the window covering jogs. Adjust to a new LOWER limit position.
STEP 3: Press and hold
confirm new limit.
my
(STOP) until the window covering jogs, to
To Change the Upper Limit:
STEP 1: Press UP
to send the window covering to its current
UPPER Limit.
STEP 2: Press and hold both UP
and DOWN
simultaneously until
the window covering jogs. Adjust to a new UPPER limit position.
STEP 3: Press and hold
confirm new limit.
my
(STOP) until the window covering jogs, to
Setting Intermediate Preferred “MY” Position
Press the
or
to operate window covering. At the desired
intermediate “my” position press my (STOP) briefly to stop the
window covering.
Once the desired “my” position is reached, press and hold my (STOP)
until the window covering jogs. The “my” position is now added
to memory.
36
Activating the “MY” Position
Send the window covering to the “my” position by pressing
from ANY window covering position.
!
my
(STOP)
Window covering should be stationary prior to activating “my”
position function. If window covering is actively moving (in-motion)
my (STOP) should be pressed twice.
Deleting “MY” Position
Activate window covering to intermediate position, then press and
hold my (STOP) for 5 seconds. Window covering will jog to confirming
deletion of “my” position.
Adding or Deleting a Transmitter
(Single Channel, Multi Channel, or Sensor)
Programmed Transmitter
STEP 1: Using an already programmed transmitter, select the transmitter
(single channel) or the channel (1-5 of a multi-channel transmitter, or
the sensor). Step 1 should not be performed with the transmitter
intended for deletion.
Programmed
Transmitter
STEP 2: Press and hold the PROGRAMMING BUTTON of that transmitter
or sensor until the window covering jogs.
Transmitter to Add or Delete
STEP 1: Select the transmitter (single channel) or the channel, (1-5
of a multi-channel transmitter, or the sensor) to be added or deleted.
Transmitter
to Add
Or Delete
STEP 2: Press and hold the PROGRAMMING BUTTON of that transmitter
or sensor until the window covering jogs.
37
Resetting All Pre-Programmed Limit Settings & Channels
LT30 WireFreeTM Roll Up Motors LT-30 RTS 12V DC
Using a paper clip, press and hold the PROGRAM
BUTTON located on the motor head until window
covering jogs 3 times, then release button. All
transmitters and limits will be erased (motor is
now reset to FACTORY MODE). Motor limits will
need to be reestablished. Please return back
to PROGRAMMING MODE to initiate
programming process.
ST30 Sonesse® 30 24V DC
Using a paperclip, press and hold the PROGRAM
BUTTON (approximately 15 seconds) until the
window covering jogs 3 times. All transmitters
and limits will be erased (motor is now reset to
FACTORY MODE). Motor limits will need to be
reestablished. Please return back to
PROGRAMMING MODE to initiate
CL 32 Cord Lift WireFreeTM RTS Motors
BUTTON, located on the back side of the motor
casing until window covering jogs 3 times, then
release button. All transmitters and limits will
be erased (motor is now reset to FACTORY MODE.)
Motor limits will need to be reestablished.
Please return back to PROGRAMMING MODE to
initiate programming process.
CT32 Cord Lift WireFreeTM RTS Motors
BUTTON, located on the top of the motor casing
until window covering jogs 3 times, then release
button. All transmitters and limits will be erased
(motor is now reset to FACTORY MODE.) Motor
limits will need to be reestablished.
Please return back to PROGRAMMING MODE to
initiate programming process.
38
Resetting Altus RTS 110 V AC
Perform a Dual Power Cut to delete all previous settings and return
motor to FACTORY MODE.
1
Remove plug from
power for 2 Seconds
2
Plug-in power cord for
10 Seconds
3
Remove plug from
power for 2 Seconds
4
Plug-in power cord.
Window covering will
begin to move.
When the window covering stops, press and hold
the PROGRAMMING BUTTON of any transmitter until
the window covering jogs twice. Do not release
the PROGRAMMING BUTTON until the jogging is complete
or you will have to start the dual power cut from the
beginning.
39
QUICK PROGRAMMING GUIDE FOR TILT WIREFREE™ RTS MOTOR
FACTORY MODE
BEFORE YOU BEGIN
The following steps must be completed to ensure proper blind
programming and functionality. Power should ONLY be connected
to current blind being programmed. All other blinds should be disconnected from
their respective power while programming is in progress. While programming,
blind should not be inactive for longer than 2 minutes or motor will exit
programming mode.
Connect Power to Motor
!
Programming Instructions are for use with all RTS transmitters
Connect 12V battery wand or transformer to the
motor. Motor should already be installed in blind.
PROGRAMMING MODE
For Single Channel Transmitters
and DOWN
simultaneously
until the blind jogs (blind slats have a short up and down tilt movement).
For Five Channel Transmitters
Using the channel selector, select the desired channel. On the transmitter, press
and hold both the UP
and DOWN
simultaneously until the blind jogs.
!
This step cannot be performed if the transmitter has already been
programmed (memorized) to blind.
Check the Direction of Operation
MUST BE DETERMINED BEFORE SETTING BLIND LIMITS
STEP 1: Press and hold the DOWN
button and confirm the blind tilts down.
STEP 2: Press and hold the UP
button and confirm the blind tilts up.
-If blind direction is not correct (in reverse), press and hold the my (STOP) on
the transmitter until the blind jogs.
Blind direction is now corrected.
Blind movement should now correspond to the direction button on
the transmitter.
40
Setting Limits
Starting with Slats in DOWN Position
or DOWN
button on the transmitter to
reach the desired LOWER limit (closed slat position).
STEP 2: Once the desired lower limit (closed slat position) is reached, press and
hold both the my (STOP) and UP
button simultaneously until the blind
begins to tilt upward, then release.
STEP 3: Press the my (STOP) button when the blind reaches the desired UPPER
limit (closed slat position). If necessary, adjust the desired slat position with a
brief press of either the UP
or DOWN
button until position is reached.
STEP 4: Once desired UPPER limit (closed slat position) is reached, press and hold
both the my (STOP) and DOWN
buttons simultaneously until the blind begins
to tilt downward, then release.
STEP 5: Once blind stops at previously set LOWER limit (closed slat position), press
and hold the my (STOP) button for until the slats jog. This confirms both limits
(slat positions).
Starting with Slats in UP Position
or DOWN
on the transmitter to reach the desired UPPER
limit (closed slat position).
button
STEP 2: Once the desired UPPER limit (closed slat position) is reached,
press and hold both the my (STOP) and DOWN
buttons
simultaneously until the blind begins to tilt downward, then release.
STEP 3: Press the my (STOP) button when the blind reaches the desired LOWER
limit (closed slat position). If necessary, adjust the desired slat position with a
brief press of either the UP
or DOWN
button.
STEP 4: Once desired LOWER limit (closed slat position) is reached, press and
hold both the (STOP) my and UP
simultaneously until the blind begins
to tilt upward, then release.
STEP 5: Once blind stops at previously set UPPER limit (closed slat position), press
and hold the my (STOP) for button until the slats jog. This confirms both limits
(slat positions).
Proceed to STEP 6 to complete programming.
41
Completing Programming and Exiting PROGRAMMING MODE
Step 6: Using a paperclip or pen, press and hold the PROGRAM
BUTTON on the back of the transmitter until the blind jogs.
TRANSMITTER IS NOW MEMORIZED AND PROGRAMMING IS COMPLETE.
!
If power is disconnected from blind before this step is completed,
TRANSMITTER WILL NOT BE MEMORIZED to the programmed blind however
limits (slat positions) will remain programmed. If this occurs, go back
and repeat step on Initiating Programming, then immediately return
to STEP 6 to complete programming.
USER MODE
Adding Additional Transmitters or Assigning Channels
(Single Channel)
STEP 1: Using a paperclip or pen, press and hold the PROGRAM BUTTON
on the previously recorded transmitter until the blind jogs.
on the Additional (new) transmitter until the blind jogs. Additional
(new) transmitter is now added to blind memory and can be used
to operate blind.
Assigning Specific Channels to Blind
(Multi-Channel Transmitters Only)
on the previously addressed transmitter until the blind jogs.
STEP 2: Select the desired channel (1-4 or all) by momentarily pressing
the Channel Selector Button on the multi-channel transmitter.
STEP 3: Press and hold the PROGRAM BUTTON on the multi-channel
transmitter until the blind jogs. Additional (new) channel is now added
to blinds memory and can be used to operate blind.
!
42
To prevent unwanted Channel/Transmitter assignments, ALL
PREVIOUSLY PROGRAMMED BLINDS should be UNPLUGGED until
Programming is complete.
Deleting Specific Channels/Transmitters
STEP 1: Using a paperclip or pen, press and hold the
PROGRAM BUTTON on the previously addressed transmitter
until the blind jogs.
!
Step 1 should not be performed with the transmitter intended for deletion.
STEP 2: Select the desired channel (1-4 or all) or transmitter
(single channel) to be deleted.
STEP 3: Press and hold the PROGRAM BUTTON on the transmitter until
the blind jogs. Channel or transmitter is now deleted from the blind
memory and will not operate blind.
Setting an Intermediate (Preferred “MY” Position)
STEP 1: Press the UP
or DOWN
directional button on the previously
addressed transmitter until the blind slats reach a desired “my” position,
then press the my (STOP) button to stop. If necessary adjust the desired slat
position by pressing and holding either the UP
or DOWN
button.
STEP 2: Press and hold the my (STOP) button on the transmitter until the
blind jogs. The “my” slat position is now added to memory.
STEP 3: Activate the blind “my” position by pressing the
from any slat position.
my
(STOP) button
Deleting “MY” Position
Activate window covering to intermediate position, then press and
hold my (STOP) for 5 seconds. Window covering will jog to confirming
deletion of “my” position.
!
Blind should be stationary prior to activating “my” position function.
If slats are actively moving (in-motion) the my (STOP) button should
be pressed twice.
43
Re-adjusting Upper Limit (UP Slat Position)
the pre-set UP limit.
directional button on the transmitter. Blind will tilt to
STEP 2: Once blind stops at pre-set up limit, press and hold both the UP
and DOWN
buttons simultaneously on the transmitter until the blind jogs.
STEP 3: Press and hold either the UP
to adjust slats to new position.
or DOWN
button on the transmitter
STEP 4: Press and hold the my (STOP) button until the blind jogs. New Upper
Limit (UP, STOP Position) is now recorded to memory.
Re-adjusting Lower Limit (DOWN Slat Position)
STEP 1: Press the DOWN
the pre-set DOWN limit.
button on the transmitter. Blind will tilt to
STEP 2: Once blind stops at pre-set down limit, press and hold both the UP
and DOWN
buttons simultaneously on the transmitter until the blind jogs.
STEP 3: Press and hold either the UP
to adjust slats to new position.
or DOWN
button on the transmitter
STEP 4: Press and hold the my (STOP) button until blind jogs. New lower limit
(DOWN STOP Position) is now recorded to memory.
Operating the Blind (tilting the slats)
UP & DOWN Positions (Telis and DecoFlex controls)
Operating at Full Speed: Press momentarily on the UP
button to tilt slats
upward or the DOWN
button to tilt slats downward closing the blind slats.
Operating at ½ Speed: Press and hold the UP
button to tilt the blind
slats upward or the DOWN
button to tilt blind slats downward.
44
Modulis Only - UP
Press momentarily on the UP
button to tilt blind slats upward.
Press the my (STOP) button to stop the movement of the slats.
Modulis Only - DOWN
Press momentarily on the (DOWN)
button to tilt blind slats
downward. Press the my (STOP) button to stop the movement of the
slats.
Modulis Only: Using the Scroll Wheel
For precise slat positioning scroll the wheel of the Modulis
transmitter to move the blind slats up or down. The slats will
move in relation to the motion of the wheel on the transmitter.
Activate the Preferred “MY” Position
Press momentarily on the my (STOP) button. The slats will start moving and
stop at the pre-programmed my (STOP) “Preferred” slat position.
Resetting all Pre-Programmed Limit Settings & Channels
Programming/Reset Button
To Delete ALL Transmitter Channels: Using a paperclip, press and hold the
PROGRAM BUTTON located on the motor head casing until blind jogs 2 times
then release.
To Delete all Previous Settings: Using a paperclip, press and hold the PROGRAM
BUTTON, located on the top of the motor casing until window covering jogs 3
times, then release button. All transmitters and limits will be erased. (Motor is
now reset to FACTORY MODE). Motor limits will need to be reestablished.
Please return to PROGRAMMING MODE to initiate programming process.
45
QUICK PROGRAMMING GUIDE FOR LT RTS CMO MOTOR
FACTORY MODE
This mode allows for rotation direction modification and setting
of the end limits.
DESCRIPTION
The LT RTS CMO is designed for rolling blinds, awnings and shutters.
The LT RTS CMO must be programmed with the RTS family of transmitters.
The LT RTS CMO motors are compatible with a Soliris RTS and Eolis RTS Sun &
Wind sensors.
!
BEFORE YOU BEGIN
For initial programming, provide power only to the motor being programmed. For awning installations, an awning hood is strongly
recommended and a drip loop should be formed to prevent water
from entering the head of the motor as shown in Figure 1.
Installer or user must verify the following Awning Installations
Hand-Held transmitter (DOWN) command:
Shutter Installations:
= shutter moves downward or closes
STEP 1: Two positions have to be set, the UP and DOWN limits. This is achieved
with the mechanical CMO limit switch unit. Provide power to the motor. Notice
the motor will not respond to any transmitter until a transmitter is assigned
to communicate with the motor receiver. Remove the protective cap exposing
the limit setting buttons on the motor head (replace when finished).
STEP 2: Depress fully both limit switch buttons. They will automatically lock in
the down position (See Figure 2).
FIGURE 2
FIGURE 1
AWNING
HOOD
WHITE PUSH
BUTTON
White
Drip
Loop
46
Gr
NEUTRAL
ee
n
GROUND
120 VAC
60 Hz
HOT
k
ac
Bl
YELLOW PUSH
BUTTON
WHITE PUSH
BUTTON
YELLOW PUSH
BUTTON
PROGRAMMING MODE
Initiate PROGRAMMING MODE
STEP 1: Assign the transmitter to communicate with the motor’s receiver, press
and hold the UP
and DOWN
buttons on the transmitter simultaneously.
STEP 2: Release both buttons after the end-product jogs briefly UP and DOWN
indicating that this transmitter can operate the motor during programming.
The LT RTS CMO motor will now operate in a momentary fashion.
!
turn the power off to the motor for 2 seconds and then back on to
reset the motor. Please return to PROGRAMMING MODE to initiate
STEP 1: The DOWN
button must correspond to DOWN on the end-product.
In case of an awning, it will open or extend the awning. If the direction is
wrong, change the direction.
STEP 2: Press and hold the
my
(STOP) button.
STEP 3: Release the my (STOP) button when the end-product jogs briefly
indicating that the change has been memorized in the motor. Verify that the
change took place before proceeding.
Mechanical Limit Setting Mode
White Button
Yellow Button
Completing Programming of Transmitters
STEP 1: Identify the UP limit switch push button on the CMO motor head.
Press the button of the transmitter and let the end-product reach the required
UP position, then stop it.
STEP 2: Unlock the UP limit switch push button by pressing and releasing it.
STEP 3: Repeat the above operation to set the DOWN end limit.
STEP 4: Replace the protective cap.
STEP 5: Press PROGRAMMING BUTTON on back of RTS transmitter to record
it to the motor memory.
47
USER MODE
This mode is for operating the motor by the end user. Two intermediate
positions my positions (IP1 & IP2) can be programmed into the LT RTS CMO
motor. IP1 is set using the UP limit as a reference and IP2 is set from the
DOWN limit as a reference.
Intermediate Position 1
Recording the Intermediate Position (IP1) referenced
from the UP Limit of the end-product.
STEP 1: Briefly press UP
to send awning to the UPPER Limit, then briefly
press my (STOP) once it is reached.
STEP 2: Press and hold both the my (STOP) and DOWN
buttons
simultaneously of the RTS transmitter and release them when the endproduct begins to move.
STEP 3: Stop the end-product at the intermediate position you wish
to achieve.
STEP 4: Press and hold the my (STOP) button of the RTS transmitter until the
end-product jogs briefly UP & DOWN indicating that the LT RTS CMO motor has
memorized the first intermediate position IP1.
Intermediate Position 2
Recording the Intermediate Position (IP2) referenced
from the DOWN Limit of the end-product.
STEP 1: Briefly press DOWN
to send awning to the fully extended position,
then briefly press my (STOP) once it is reached.
STEP 2: Press and hold both the my (STOP) and UP
buttons
simultaneously of the RTS transmitter and release them when the end-product
begins to move.
STEP 3: Stop the end-product at the intermediate position you wish
to achieve.
STEP 4: Press and hold the my (STOP) button of the RTS transmitter until
the end-product jogs briefly UP & DOWN indicating that the LT RTS CMO motor
has memorized the first intermediate position IP2.
48
Adding Additional Transmitters/Sensors
(Single Channel)
on the previously recorded transmitter until the awning jogs.
on the Additional (new) transmitter/sensor until the awning jogs.
Resetting Back to FACTORY MODE
Resetting Motor Memory and Recording New Transmitter
Step 1: Perform a dual power cut in the following sequence:
1. Power-off 2 second minimum
! New Transmitter
2. Power-on 10 seconds
4. Power-on
>5 sec.
The end product moves for 5 seconds in one direction, to indicate that the double
power cut has been recorded. The motor is in PROGRAMMING MODE for 2 minutes.
Step 2: Press and hold more than 5 seconds on the PROGRAMMING BUTTON
of the PREVIOUSLY recorded RTS transmitter/channel. The end-product jogs briefly
UP or DOWN indicating that the LT RTS CMO motor memory has recorded this
new transmitter.
Back to FACTORY MODE (To completely reset the LT RTS CMO motor’s memory)
Step 1: Perform a dual power cut in the following sequence:
! Previously Recorded Transmitter
2. Power-on 5 to 15 seconds
4. Power-on
>5 sec.
The end product moves for 5 seconds in one direction, to indicate that the dual
power cut has been recorded. The motor is in PROGRAMMING MODE for 2 minutes.
Step 2: Press and hold more than 5 seconds on the PROGRAMMING BUTTON of
the PREVIOUSLY recorded RTS transmitter/channel. The end-product jogs briefly
UP or DOWN indicating that the LT RTS CMO motor memory has been completely
cleared.
!
The motor cannot be reset if it is already in FACTORY MODE.
49
QUICK PROGRAMMING FOR SUNEA™ RTS CMO MOTOR
FACTORY MODE
DESCRIPTION
The Sunea™ RTS CMO has 3 main features:
1. Universal motor for Retractable Awnings and Cassette Awnings
2. Back release function at top of end limit
3. Possibility to choose the closing force.
BEFORE YOU BEGIN
For initial programming, provide power only to the motor being programmed. For awning installations, an awning hood is strongly
recommended and a drip loop should be formed to prevent water
from entering the head of the motor.
Installer or user must verify the following Awning Installations
Hand-Held transmitter (DOWN) command:
Connect Power to Motor
Connect 120 V AC to the Sunea™ motor
via the proper extension cable with
NEMA plug.
PROGRAMMING MODE
and DOWN
simultaneously until the awning jogs. A jog is a brief up and down or in
and out motion. In PROGRAMMING MODE, the awning will move only
when the UP
or DOWN
is held (or momentary fashion).
50
Press and hold UP
or DOWN
. When pressing DOWN
product
should go down or out. If awning direction does not correspond with UP
or DOWN
you must REVERSE the output direction. To reverse output
direction, simply press & hold the my (STOP) until the awning jogs. Output
direction should now correspond.
Setting Limits For Standard Retractable Awning
(Both UP and DOWN Limits need to be set)
STEP 1: Bring the awning to your desired UPPER limit with the transmitter.
Press and hold both the my (STOP) and DOWN
buttons simultaneously
until the awning begins to move down, then release. Stop the motor where
the LOWER limit should be set. You can adjust by pressing the UP
or
DOWN
buttons.
until the awning begins to move up. The motor will stop at the original UPPER
point.
STEP 3: Press and hold the my (STOP) button until the awning performs a long
jog (a hard UP limit stop will take place, then release).
STEP 4: Press and hold the PROGRAM BUTTON on the back of the transmitter until
the awning jogs. It will now operate in a maintained fashion. Double check limits
as a precaution.
Setting Limits For Cassette Awnings
(Only DOWN Limit needs to be set.
Automatic Limit is set for UP Limit)
!
Limit setting must start from the DOWN or extended position. Do not
start limit setting from the UP position as it is automatically set.
turn the power off to the motor for 2 seconds and then back on to reset
the motor. Please return to PROGRAMMING MODE to initiate
STEP 1: Bring the awning to your desired down limit with the transmitter. Press
and hold both the my (STOP) and UP
buttons simultaneously until the
awning begins to move up, then release.
STEP 2: Press the my (STOP) button and stop the awning halfway UP, before
the UP limit is reached.
51
STEP 3: Press and hold my (STOP) the button again until the awning moves to
set its UPPER limit automatically and confirm
STEP 4: Press and hold the PROGRAM BUTTON on the back of the transmitter until
the awning jogs. It will now operate in a maintained fashion. Double check
limits as a precaution.
Adjusting the Limits
To Change the LOWER Limit:
Send the motor to its current LOWER limit position with the transmitter and let
it stop. Press and hold both the UP
and DOWN
until the awning jogs, then release. Adjust to a new LOWER limit position. Press
the my (STOP) button until the awning jogs, then release. Check new limit.
To Change the UPPER Limit: (Only For Retractable Awning)
Send the motor to its current UPPER limit position with the transmitter and let
it stop. Press the and hold both the UP
and DOWN
until the awning jogs, then release. Adjust to a new UPPER limit position. Press
the my (STOP) button until the awning jogs, then release. Check new limit.
Adding or Deleting a Transmitter
(Single Channel, Multi Channel, or Sensor)
Adding a Remote/Channel or Sun and Wind Sensor: First press the
PROGRAMMING BUTTON on the back of the already programmed remote until the
awning jogs. Then press the PROGRAMMING BUTTON on the remote or sun/wind
sensor that you would like to add until the awning jogs. Check it.
Resetting All Pre-Programmed Limit Settings & Channels: You will need to
disconnect power (120V AC) for 2 seconds, reconnect for 10 seconds, disconnect
for another 2 seconds and reconnect. The motor should start to move and then
stop on its own. If this does not happen, continue to perform the disconnects
until it does. Once the motor stops moving on its own, press and hold the
PROGRAMMING BUTTON on the back of the remote until the awning jogs twice.
All transmitters and limits will be erased (motor is now in FACTORY MODE). Motor
limits will need to be reestablished. Please return back to PROGRAMMING MODE
to initiate programming process.
Advanced Features Function
!
52
BACK IMPULSE Function for both Standard Retractable and Cassette Awnings
This function allows you to apply tension on the fabric when the awning
is fully extended. The motor can be adjusted up to a ½ half turn.
STEP 1: Set the awning to the lowest position.
To Activate this Function:
until the awning jogs. The motor is in PROGRAMMING MODE.
STEP 3: Adjust the fabric's tension using the UP
or DOWN
buttons.
STEP 4: Press the
(STOP) button until the awning jogs. The fabric's tension
has been programmed.
my
BACK RELEASE Function on Cassette Awnings Only
!
This function allows the fabric tension to be released after the cassette
awning is closed.
Set the awning to the UP or CLOSED limit position with the transmitter.
STEP 1: Cut the power for 2 sec, then plug back in, unless you are using the
awning in the first 4 cycles.
Press and hold both the my (STOP) and DOWN
buttons simultaneously until
the awning jogs. If the Back release function was deactivated, it
is activated. If the Back Release function was active, it is deactivated.
CLOSING FORCE Adjustment For on Cassette Awnings Only
!
This function enables the closing force of the cassette awning to be increased
or decreased to 3 levels (high/medium/low). The motor is factory set at the
medium level.
STEP 1: Bring the awning to the halfway position.
STEP 2: Cut the power for 2 sec, then plug back in, unless you are using the
awning in the first 4 cycles.
STEP 3: Briefly press the my (STOP) and UP
buttons simultaneously, then
immediately press and hold the my (STOP) and UP
until the motor jogs. The motor is only in PROGRAMMING MODE for approx.
10 seconds.
STEP 4: Adjust the closing force setting using the UP
and DOWN
buttons.
- to increase the closing force, press the UP
button until the motor jogs up
and down.
- to decrease the closing force, press the DOWN
button until the motor jogs
up and down (long jog for levels 3 and 1) (short jog for level 2).
STEP 5: Press and hold the my (STOP) button until the awning jogs up and down.
The new closing force has been programmed.
53
QUICK PROGRAMMING FOR Oximo™ RTS MOTOR
Auto Set Both Limits
To allow Oximo to auto set limits, the product must have rigid links and bottom stops.
STEP 1: Wake the motor by pressing the UP
simultaneously until the motor jogs.
and DOWN
buttons
NOTE: After every command the motor will jog to confirm.
STEP 2: Check the direction of rotation with the UP
or DOWN
button. If needed, change the direction of rotation by pressing and
holding the “my” my button until the motor jogs.
motor jogs.
and DOWN
STEP 4: Press and hold the “my”
confirm the limit setting.
my
button until the motor jogs to
STEP 5: Press and hold the PROGRAM button on the back of the
transmitter until the motor jogs. The buttons no longer have to be held
for the motor to run. The motor will auto detect the non-set limit from
the physical stop.
Top Limit Set by User, Bottom Limit Auto Set
To allow Oximo to auto set the bottom limit, the product must have rigid links.
and DOWN
buttons
or DOWN
STEP 3: Run the motor to the desired upper limit. Press the “my” my
and DOWN
buttons simultaneously until the motor starts to run
downward. Use the “my” my button to stop the motor.
my
the physical stop.
54
General Informartion
ADJUSTING THE LIMITS AFTER THE MOTOR HAS BEEN PROGRAMMED.
To change the upper limit, run the motor to its upper limit and let it stop.
Press the UP
and DOWN
buttons simultaneously until the motor jogs.
Run the motor to the new desired upper limit. Press and hold the “my” my
button until the motor jogs. Check the new limit.
To change the lower limit, run the motor to its lower limit and let it stop.
Press the UP
and DOWN
buttons simultaneously until the motor jogs.
Run the motor to the new desired lower limit. Press and hold the “my” my
button until the motor jogs. Check the new limit.
Bottom Limit Set by User, Top Limit Auto Set
To allow Oximo to auto set the top limit, the product must have a bottom
stop.
and DOWN
buttons
or DOWN
STEP 3: Run the motor to the desired lower limit. Press the “my”
andUP
buttons simultaneously until the motor starts to run
upward. Use the “my” my button to stop the motor.
my
my
the physical stop.
55
Both Limits Set by User
and DOWN
buttons
or DOWN
STEP 3: Run the motor to the desired upper limit. Press the “my” my and
UP
buttons simultaneously until the motor starts to run downward.
Use the “my” my button to stop the motor near the desired lower limit.
STEP 4: Use the UP
or DOWN
button to run the motor to the exact
desired lower limit. Press the “my” my and UP
buttons
simultaneously until the motor starts to run. Use the “my” my button to
stop the motor.
confirm the limit settings.
my
Note: Until this step, the up or down limit can be adjusted by repeating
step 3 or step 4.
for the motor to run. Double check the limits are in the desired position.
General Informartion
To add or delete a remote/channel, press the PROGRAMMING button on the
back of an already programmed remote/channel until the motor jogs. Next,
press the PROGRAMMING button on the back of the remote/channel you wish
to add or delete until the motor jogs.
To reset the motor to factory mode, start with the motor connected to power.
Cut power for 2 seconds, reconnect power for 10 seconds, cut power for 2
seconds and then reconnect power. The motor should jog or start to run. (If this
does not happen, repeat the power cuts until the motor does run). Allow the
motor to stop on its own. (Do not press stop, up or down or you will have to
repeat the double power cut). Once the motor stops on its own, press and hold
the PROGRAMMING button until the motor jogs twice.
56
QUICK PROGRAMMING FOR GLYDEA ® RTS
DESCRIPTION
2 motors: Glydea 35e RTS, Glydea 60e RTS
120 V AC with integrated power supply 10 foot cable
Motor placement left or right and/or
upside down installation
New touch motion
Comes in Dry contact with optional RTS
plug-in module
Standard mounting
Inverse Mounting
BEFORE YOU BEGIN
Manually move drapery to a middle position along the track.
This allows for movement of the motor in either direction.
Motors are equipped
with a NEMA power plug.
Programming the RTS control point
STEP 1: Press and hold the OPEN/UP
and CLOSE/DOWN
buttons
simultaneously on the RTS transmitter until the drapery jogs.
STEP 2: Briefly press OPEN/UP
or CLOSE/DOWN
runs to record both hard stop positions.
, the drapery automatically
Checking the direction of operation
STEP 1: Press the RTS transmitter OPEN/UP
button.
- If the drapery opens, the direction of rotation is correct, go to STEP 3.
- If the drapery closes, the direction of rotation is incorrect, go to STEP 2.
STEP 2: Press the my (STOP) button until the drapery jogs: the direction of
rotation has been modified. Press the OPEN/UP
button to check the
direction of rotation.
STEP 3: Recording the RTS Transmitter: Press the PROGRAMMING BUTTON
on the back of the RTS transmitter until the drapery jogs. The RTS
transmitter is now recorded.
Press the OPEN/UP
drapery.
button or CLOSE/DOWN
button to operate
57
Setting Intermediate Preferred “My” Position:
Recording “my” favorite position:
STEP 1: To set the “my” my (STOP) position, move the drapery to the desired
intermediate position with the OPEN/UP
or CLOSE/DOWN
buttons.
STEP 2: Press the “my”
my
(STOP) button until the drapery jogs to confirm setting.
Delete the “my” position:
To delete the “my” (STOP) position, move the drapery to the current
“my” my (STOP) position, then press the my (STOP) button until the drapery
jogs.
Adjusting The Limits:
STEP 1: Press the OPEN/UP
button or CLOSE/DOWN
drapery to the limit to be re-adjusted.
button to move the
and CLOSE/DOWN
simultaneously until the drapery jogs.
or CLOSE/DOWN
the drapery to the new desired position.
STEP 4: To confirm the new limit, press and hold the
the drapery jogs.
my
buttons
buttons to move
(STOP) button until
Modifying the motor Rotation Direction
STEP 1: Press OPEN/UP
away from the limit:
or CLOSE/DOWN
button to move the drapery
and CLOSE/DOWN
buttons
STEP 3: Press the my (STOP) button until the drapery jogs to reverse the
rotation direction.
58
Dry Contact Mode Setting
from the limit:
or CLOSE/DOWN
button to move the drapery away
and CLOSE/DOWN
STEP 3: Press the
the drapery jogs.
my
(STOP) and CLOSE/DOWN
buttons
buttons simultaneously until
Activating the Touch Motion Feature
NOTE: The Glydea by default does not have the touch motion feature activated.
away from the limit.
or CLOSE/DOWN
button to move the drapery
and CLOSE/DOWN
button
STEP 3: NOTE - Be sure to follow the steps associated with your desired
sensitivity setting.
To activate the Standard Sensitivity Setting (more sensitive)
Press the OPEN/UP
and CLOSE/DOWN
drapery jogs (total of 2 jogs) then proceed to Step 4.
To activate the Low Sensitivity Setting (less sensitive)
Press the OPEN/UP
and CLOSE/DOWN
drapery jogs once. Then press the OPEN/UP
and CLOSE/DOWN
buttons
simultaneously until the drapery jogs again (total of 3 jogs). Proceed to Step 4.
STEP 4: Press the
my
(STOP) button until the drapery jogs to confirm the setting.
59
Adjustment Of Speed Setting:
STEP 1: Press and hold both the my (STOP) and OPEN/UP
buttons
simultaneously until the drapery starts to open and close automatically.
STEP 3: Press the
my
to increase speed, CLOSE/DOWN
to decrease speed
(STOP) button until the drapery jogs to confirm the setting.
Deleting Specific Channels/Transmitters
on the previously addressed transmitter until the drapery jogs.
!
Step 1 should not be performed with the transmitter intended for deletion.
STEP 2: Select the desired channel (1-4 or all) or transmitter
(single channel) to be deleted.
STEP 3: Press and hold the PROGRAM BUTTON on the transmitter until
the drapery jogs. Channel or transmitter is now deleted from the drapery
memory and will not operate the drapery.
Deleting Previous Setting
To delete all the transmitters programmed and retain limit setting, press and
hold the receiver PROGRAM BUTTON until the drapery jogs twice.
Resetting completely the memory of the motor, press the receiver’s
PROGRAM BUTTON until the drapery jogs 3 times. All the settings are erased.
60
QUICK PROGRAMMING FOR OUTDOOR LIGHTING RECEIVER RTS
PROGRAMMING MODE
Add The First Transmitter To The Memory
Step 1: Press the PROGRAMMING BUTTON, on the Outdoor Lighting Receiver RTS
for more than 2 seconds.
Step 2: The programming LED on the receiver will illuminate, and the lamp will
light for 2 seconds.
Step 3: Press the PROGRAMMING BUTTON on the new transmitter to add it to the
receiver. The programming LED on the Receiver will blink, and the lamp will light
indicating the transmitter is memorized.
Add the First Transmitter to the Memory
STEP 1: Press the PROGRAMMING BUTTON, on the Lighting Receiver for more than
2 seconds.
STEP 2: The programming LED on the receiver will light, and the lamp will light for
2 seconds.
STEP 3: Press the PROGRAMMING BUTTON on the new transmitter to attach it to the
receiver. The programming LED on the Receiver will blink, and the lamp will
light indicating the transmitter is memorized.
Adding a New Transmitter to the Memory
STEP 1: Press the PROGRAMMING BUTTON, for more than 2 seconds, on a transmitter
that is already memorized by the Lighting Receiver.
STEP 2: The programming LED on the receiver will light, and the lamp will light for
2 seconds.
STEP 3: Press the PROGRAMMING BUTTON on the new transmitter to attach it to the
receiver. The programming LED on the receiver will blink, and the lamp will light
indicating the transmitter is memorized.
Removing all transmitters from memory
Press and hold the
PROGRAMMING BUTTON of
the receiver for more than
7 seconds until the LED
blinks and the light flashes
twice. This
LAMP
removes ALL
500 WATTS MAX.
memorized
transmitters
or sensors.
PROGRAMMING BUTTON
GROUND
PROGRAMMING LED
500W Max
Lighting Output
NEUT
HOT
NEUT
HOT
GROUND
NEUTRAL
HOT
61
QUICK PROGRAMMING FOR OUTDOOR UNIVERSAL RECEIVER RTS
PROGRAMMING MODE
Add The First Transmitter To The Memory
Step 1: Press the PROGRAMMING BUTTON, on the Outdoor Universal Receiver
RTS for more than 2 seconds.
Step 2: The programming LED on the receiver will illuminate on and the
motor will jog.
Step 3: Press the PROGRAMMING BUTTON on the new transmitter to record it to
the receiver. The programming LED on the Receiver will blink, and the motor
will jog indicating the transmitter is memorized.
Step 4: Operate the motor in the DOWN
direction.
Step 5: The motorized treatment should move down or extend if this is
incorrect, turn off power to the receiver and reverse the RED and BLACK wires.
Failure to correct this error will cause damage to awning by extending it during
windy conditions
Adding a New Transmitter/Sensor to Memory
STEP 1: Set the Universal Receiver into PROGRAMMING MODE by pressing the
PROGRAMMING BUTTON until the LED lights (about 2 seconds). The motor will
jog.
STEP 2: Press the PROGRAMMING BUTTON on the Telis transmitter or RTS sensor
to be memorized. The programming LED will blink and the motor will jog
indicating the device has been memorized.
Removing All Transmitters/Sensors from Memory
Press and hold the PROGRAMMING BUTTON of the receiver for more than 7 seconds
until the LED blinks and the motor jogs twice. This removes ALL memorized
transmitters or sensors.
GROUND
PROGRAMMING BUTTON
UP
DOWN
MTR COM
MOTOR
NEUT
HOT
NEUT
R
GROUND
NEUTRAL
HOT
62
HOT
PROGRAMMING LED
QUICK PROGRAMMING FOR RTS REPEATER
The Somfy RTS Repeater can be used in installations to
extend the range of the standard Radio Technology Somfy ®
signal. It will receive the signal from a Telis or similar device
and retransmit the signal to a RTS compatible motor or
receiver.
Simply plug the receiver into any 120V AC outlet. It should
be located at least halfway between the transmitting device
(Telis) and receiving device (RTS Motor). The red LED will
blink, indicating communication.
QUICK PROGRAMMING FOR UNIVERSAL RTS INTERFACE (URTSI)
PROGRAMMING MODE
Set the RTS receiver or motor into its PROGRAMMING MODE. Refer to the
installation instructions of the relevant RTS receiver or motor for this procedure.
!
For initial programming, provide power only to the motor or control
being programmed.
Using the rotary switch, select the channels (1-9) to be programmed. Letter A
through F stand for channels 10 through 15, 0 for 16. Briefly press the
PROGRAMMING BUTTON (1 sec. max.) The window treatment will jog to indicate
the channel has been memorized.
Repeat the steps above for each channel or product to be memorized.
To test the control operation, simply press the UP, STOP or DOWN buttons on the
front of the control. The window treatment should move appropriately. The
LED will flash red to indicate the radio signal has been transmitted.
63
myLink™ INITIAL SETUP AND RTS PROGRAMMING
Pre-Installation Best Practices
1. Confirm that the RTS motorized products are fully operational from at least 1
RTS control and that all the limits are set (including the MY position if desired).
NOTE: The myLink cannot be used to set limits or add/delete RTS transmitters.
2. Make sure that the WiFi network is 2.4GHz and is using a myLink-supported
encryption type (WEP, WPA2, open and mixed mode).
3. Connect your mobile device to the network you want the myLink to join and
check the WiFi strength.
4. Know your WiFi network name (SSID) and password (if required).
5. Expect to install 1 myLink interface per zone (5 channels per myLink).
Setup
STEP 1: Download the free app from the App store or
Google Play.
STEP 2: Plug the myLink interface into a standard
110V AC outlet. Be sure to place the myLink near the motorized applications
you plan to control.
STEP 3: Open the app and press
Start new system
STEP 4: Follow the setup prompts. Confirm the status LED is solid red
indicating that the myLink is in setup mode.
STEP 5: Connect the mobile device to the myLink's WiFi network
(ex: Somfy_1234).
STEP 6: Return to the app and press
Search for myLink
STEP 7: In the network dropdown list, choose the network the myLink
will join and enter the WiFi network
password (if present) and press
Next
64
myLink™ INITIAL SETUP AND RTS PROGRAMMING
Setup Continued
STEP 8: The myLink will complete the network auto-configuration process.
Once step 4 is complete, click Continue.
NOTE: Make sure the mobile device rejoins the same WiFi network as the
myLink. If not, minimize the app, join the same WiFi network as the myLink,
and return to the app.
STEP 9: Name the myLink and select a room icon. Continue on to
RTS Programming.
STEP 10: From the RTS programming
screen, choose from the available
Click to choose an
RTS product icon
application icons.
STEP 11: Follow the on-screen
setup prompts.
a. Identify the transmitter that currently controls the motorized product
and confirm that it's working properly. Select the channel
that operates the product you wish to program.
b. Press the program button on the back of the remote
until the shade jogs.
STEP 12: Press
Program
on the
app and the shade will jog again.
NOTE: If the motorized application does not respond to the command,
press the
Retry
button to send the signal again.
STEP 13: The programming is now complete for that channel. Simply press
Create Group
channel or Press
to program additional motors to the same
Done
to add additional channels and name
them. Repeat the process to create up to five channels. Once RTS
programming is complete, press
Done
STEP 14: The myLink is now configured and ready to use. Scenes and
schedules can now be created.
65
CREATE AND EXECUTE SCENES
Scenes activate multiple Somfy-powered applications across different channels
together, even across multiple myLinks. Each myLink supports up to 25 scenes.
STEP 1: Access the scene screen from
the toggle button or menu.
STEP 2: Press the plus (
) icon to create
a scene and name it.
STEP 3: Press the plus icon again to add the
motorized products you want associated with the scene.
NOTE: If there are multiple myLinks, you will need to choose a
myLink first.
NOTE: For tablets, drag and drop the command to be added.
STEP 4: Once all commands have been added press
Done
to save.
STEP 5: To activate a scene,
press its icon.
STEP 6: To edit a scene, click the
pencil (
) icon then the scene.
To delete a scene, press the pencil
icon, then swipe from right to
left the scene to be deleted.
CREATE AND EXECUTE SCHEDULES
The schedule feature creates timed events with existing scenes. Each myLink
supports up to 25 schedules.
STEP 1: Access the schedule screen
from the scene screen or the menu.
STEP 2: Select the clock and then
press the plus (
) to create the
schedule and name it.
66
CREATE AND EXECUTE SCHEDULES CONTINUED
STEP 3: Select
Press back
Set
to schedule the time and days of activation.
then back again to save settings.
b. NOTE: Vacation mode will randomly activate the timed event within
15 minutes of its scheduled start time.
STEP 4: Press the plus (
) icon to select from available scenes. Up to
5 scenes may be added to each schedule.
STEP 5: Press
Done
The time and days associated with the
schedule are displayed. The schedule will activate at the appropriate time.
JOIN EXISTING SYSTEM
The myLink™ allows multiple users to control Somfy-powered products
from different mobile devices. They simply need to join the system in a
few short steps.
STEP 1: First download the app from
the app store or Google play.
STEP 2: Connect mobile device to the same network as the myLink.
STEP 3: Open the app, press
Join existing system
STEP 4: Enter the system's 4 digit PIN. Press
Next
STEP 5: The new user now has myLink app control of all paired RTS
products, scenes andJoin
schedules.
Existing
System
NOTE: To invite users, go to menu>mobile pin and press “Share mobile
PIN” to generate an invitation email.
NOTE: To access RTS programming after intial setup, go to menu>edit
and scroll to RTS Programming.
NOTE: To add more myLinks,
plug the myLink into a
standard 110V AC outlet and
confirm LED is solid red.
RTS
RTS Programming Settings
Connect the mobile device to
the myLink's WiFi network
(ex: Somfy_1234). Open the app and go to menu>add and follow
steps 4 through 12 above. Repeat steps 4 - 16.
67
CHANGING WIFI NETWORK INFORMATION
STEP 1: Put the myLink back into setup
mode by pressing the programming
button on the side of the myLink with
a small paper clip or similar item.
STEP 2: Confirm the status LED is solid
red indicating that the myLink is in
setup mode.
STEP 3: Connect the mobile device to the
myLink's WiFi network (ex: Somfy_1234)
STEP 4: Open the app, Go to menu>edit.
STEP 5: Choose a myLink to edit.
NOTE: If there is only one myLink, you
will go directly to the next step.
STEP 6: Select the network field and choose
from available WiFi networks.
STEP 7: Choose new network and enter the
password if present.
STEP 8: Press
Done
STEP 9: The myLink will go through the network auto-configuration to
confirm settings. The WiFi network information is now changed.
NOTE: If there are multiple myLinks in the system, steps 1-9
must be completed for each one.
68
QUICK PROGRAMMING FOR SUNIS INDOOR WIREFREE™ SENSOR
PROGRAMMING MODE
Adding a Sunis Indoor Sensor
!
During initial programming, provide power only to motorized
window covering being programmed.
STEP 1: Carefully remove rear cover to expose sensor control setting panel.
STEP 2: Slide the ON/OFF Selector Switch to the ON or
position.
STEP 3: Set the motorized window covering into PROGRAMMING MODE
(Refer to the installation instructions of the relevant RTS receiver or motor
or this procedure).
STEP 4: Using a paper clip, pen or similar device, briefly press the
PROGRAMMING BUTTON (for 1 second) located on the Sunis light sensor
(See Figure 1 pg. 69). The motorized window covering will jog to
confirm the addition of the new Sunis light sensor..
!
Repeat steps 1-3 when multiple motors are required to operate
from the Sunis light sensor.
Deleting a Sunis Indoor Sensor from Memory
STEP 1: Using a paper clip, pen or similar device, press and hold the
PROGRAMMING BUTTON (for 3 seconds) on a previously addressed Sunis
Light Sensor or Somfy transmitter (Telis, DecoFlex, etc.) (See Figure 1 pg. 69).
The motorized window covering will jog to confirm PROGRAMMING MODE.
!
Step 1 should not be performed with the Sunis intended for
deletion.
STEP 2: Using a paper clip, pen or similar device, briefly press the PROGRAMMING
BUTTON (for 1 second) located on the Sunis Light Sensor to be deleted (See Figure 1
pg. 69). The motorized window covering will jog to confirm the deletion of the
Sunis light sensor.
!
Sunis light sensor MUST be free from obstructions in order to correctly
sense incoming light. Sill mount may not be suitable for some window
installations (See Figure 2 pg. 70).
WINDOW GLASS MOUNT
SENSOR LOCATION
Outside of
Window Glass
WINDOW SILL MOUNT
Outside of
Window Glass
Front of Sunis
towards outside
of window glass
69
Setting the Light (Sun) Sensitivity (Threshold)
Sunis sensor should be mounted in or near window and
exposed to incoming light.
STEP 1: Carefully remove rear cover of Sunis Light sensor exposing control
setting panel.
position.
STEP 3: Momentarily press the MODE BUTTON. LED Indicator will illuminate for
approximately 15 seconds.
!
LED Indicator light will remain illuminated for approximately 15
seconds. Should the LED Indicator light extinguish prior to establishing
the light sensitivity (threshold) setting, simply press the MODE BUTTON
momentarily to reactivate LED light.
STEP 4: Using a small screw driver or similar device, rotate the Sun Sensitivity
Selector to the fully CLOCKWISE (+) position. LED Indicator light will illuminate
red (See Figure 3 pg. 70).
STEP 5: Slowly rotate the Sun Sensitivity Selector COUNTER CLOCKWISE (-) until
the LED Indicator illuminates to a green color. A green colored LED indicates the
present light value (threshold). At this value (threshold) the Sunis sensor will
provide the necessary DOWN COMMAND to the motorized window covering.
OPERATING MODE
!
Default employs output response time delays.
STEP 1: Refer to previous “Setting the Light (Sun) Sensitivity Threshold”
instructions.
STEP 2: Sunis light sensor will send a DOWN COMMAND to the RTS receiver or
motor after 5 minutes of sensing light within the set threshold.
STEP 3: Sunis RTS light sensor will send an UP COMMAND to the RTS receiver
or motor after 30 Minutes of sensing light that HAS FALLEN BELOW THE SET
THRESHOLD.
GREEN LED: INDICATES SUN (Light) WITHIN THRESHOLD SETTING
RED LED: INDICATES SUN (LIGHT) BELOW THRESHOLD SETTING
70
Replacing the Battery
The Sunis WireFree™ RTS Light Sensor uses a lithium battery (Type: CR2430).
LED Indicator Light will illuminate orange when battery needs replacing.
STEP 1: Carefully remove rear cover of Sunis light sensor exposing the control
setting panel (See Figure 4 pg. 70).
STEP 2: Firmly grip the molded indentations and rotate control setting panel
counter clockwise to open position.
STEP 3: Carefully separate from sensor case to expose battery holder.
STEP 4: Replace battery with correct rated/type battery. Be certain of battery
polarity (+) and (-) when installing new battery.
!
Do not use any tools when replacing the battery as there is a risk
of damaging the sensor circuitry.
Programming Figures
FIGURE 1
Rear Cover
LED
Indicator
Control
Setting Panel
Programming
Button
71
Programming Figures
FIGURE 2
Window
Glass Mount
Window
Sill Mount
Sun
Sensitivity
Selector
FIGURE 3
LED
Indicator
ON/OFF
Selector
Switch
Control
Setting
Panel
Mode
Button
(-) Requires
Less Sunlight
(+) Requires
More Sunlight
FIGURE 4
Rear
Cover
Sensor Case
Control
Setting
Panel
72
QUICK PROGRAMMING FOR THERMO SUNIS INDOOR WIREFREE™ SENSOR
Adding a Thermo Sunis Indoor Sensor
!
During initial programming, it is recommended that power
is provided only to motorized window covering being programmed.
STEP 1: Carefully remove rear cover to expose sensor control setting panel.
STEP 2: Set the motorized window covering into PROGRAMMING MODE (Refer
to the installation instructions of the relevant RTS receiver or motor for this
procedure).
Indicator will illuminate for 5 seconds then extinguish.
position. Sun LED
BUTTON (for 1 second) located on the control setting panel of the Thermo Sunis.
(See Figure 1 pg. 75). The motorized window covering will jog to confirm the
addition of the Thermo Sunis sensor.
!
Repeat steps 1-3 when multiple motorized window coverings
are required to operate from the Thermo sunis sensor.
Deleting a Thermo Sunis Indoor Sensor from Memory
STEP 1: Using a paper clip, pen or similar device, press and hold the
PROGRAMMING BUTTON (approximately 3 seconds) on a previously addressed
Thermo Sunis or Somfy transmitter. (Telis, DecoFlex, etc.). The motorized
window covering will jog to confirm PROGRAMMING MODE.
BUTTON (for 1 second) located on the control setting panel of the Thermo Sunis
to be deleted (See Figure 1 pg. 75). The motorized window covering will jog to
confirm the deletion of the Thermo Sunis sensor.
!
Step 1 should not be performed with the Thermo Sunis intended
for deletion.
!
Thermo Sunis sensor MUST BE mounted indoors only and should
be free from obstructions in order to correctly sense incoming light.
Sill mounts may not be suitable for some window installations.
(Sensor should be mounted in front of all interior window coverings
(See Figure 2 pg. 76).
SENSOR LOCATION
WINDOW GLASS MOUNT
WINDOW SILL MOUNT
Outside of
Window Glass
Outside of
Window Glass
Front of Sunis
towards outside
of window glass
73
Setting the (Temperature) Sensitivity (Threshold)
Thermo Sunis should be mounted in or near window and
exposed to incoming sunlight.
STEP 1: Carefully remove rear cover of the Thermo Sunis sensor exposing Control
Setting Panel (See Figure 4 pg. 76).
position. Sun LED
Indicator will illuminate for 5 seconds and then extinguish.
STEP 3: Momentarily press the MODE BUTTON and Sun LED Indicator Light will
illuminate for approximately 15 seconds to indicate present threshold setting.
!
seconds. Should the LED Indicator light extinguish prior to establishing
the light sensitivity (threshold) setting, simply press the MODE BUTTON
momentarily to reactivate LED light.
STEP 4: Using a small screw driver or similar device, rotate the Sun Sensitivity
Selector to the fully CLOCKWISE (+) position. LED Indicator will remain illuminated
red color (See Figure 3 pg. 76).
STEP 5: Slowly rotate the Sun Sensitivity Selector COUNTER CLOCKWISE (-)
until the LED Indicator illuminates to a green color. A green colored LED
indicates the present light value (threshold). At this (threshold) the Thermo
Sunis sensor will provide the necessary RTS command as selected with the
Function Selector Switch (See Figure 3 pg. 76).
GREEN LED: INDICATES SUNLIGHT WITHIN THRESHOLD SETTING
RED LED: INDICATE SUNLIGHT BELOW THRESHOLD SETTING
!
74
Rotating the Sun Sensitivity Selector to a FULL COUNTER CLOCKWISE
(-) position will simulate sun if no sun is present. It is not
recommended to leave the selector (threshold setting) in this position.
Setting the (temperature) Sensitivity (threshold)
Thermo Sunis should be mounted in or near window and exposed
to incoming sunlight.
Step 1: Carefully remove rear cover of the Thermo Sunis sensor exposing
Control Setting Panel (See Figure 4 pg. 76).
Step 2: Slide the ON/OFF Selector Switch to the ON or
position. Sun
LED Indicator will illuminate for 5 seconds and then extinguish.
Step 3: Momentarily press the MODE BUTTON. Temperature LED Indicator
will illuminate for approximately 15 seconds to indicate present threshold
setting.
!
seconds. Should the LED indicator light extinguish prior to establishing
the temperature sensitivity (threshold) setting, simply press the MODE
BUTTON momentarily to reactivate LED light.
Step 4: Using a small screw driver or similar device, rotate the Temperature
Sensitivity Selector to the fully CLOCKWISE (+) position. Temperature LED Indicator
will remain illuminated red color (See Figure 3 pg. 76).
Step 5: Slowly rotate the Temperature Sensitivity Selector COUNTER CLOCKWISE (-)
until the LED Indicator illuminates to a green color. A green colored LED indicates
the present temperature value (threshold). At this value (threshold) the
Thermo Sunis sensor will provide the necessary RTS command as selected with the
Function Selector Switch (See Figure 3 pg. 76).
GREEN LED: INDICATES TEMPERATURE WITHIN THRESHOLD SETTING
RED LED: INDICATES TEMPERATURE BELOW THRESHOLD SETTING
75
OPERATING MODE
!
Default employs output response time delays.
STEP 1: Slide the Sun/Temp Selector Switch to the desired setting
(See Figure 3 pg. 76).
= Activation of Window Covering via Sunlight only
= Activation of Window Covering via Temperature & Sunlight
STEP 2: Adjust Sunlight and Temperature Sensitivity (threshold) (Refer to Setting
theSensor Sensitivity (threshold).
OR
Slide the Function Selector Switch to provide the necessary RTS output commands
to the window covering.
*Command Mode 1
Command Mode 2
2
1
After 5 Minutes
(within threshold)
Go to DOWN Limit
or Sensor Location
After 30 Minutes
(below threshold)
Go to UP Limit
Command Mode 3
3
Go to DOWN Limit
Go to "my” Position
my
Go to "my” Position
Go to UP Limit
my
= Sunlight/Temp sensor within the set “Threshold.” Thermo Sunis will
provide an RTS command after approximately 5 minutes of sensing
within the set threshold.
= Sunlight/Temp Sensor below the set “Threshold.” Thermo Sunis will
provide an RTS command after approximately 30 minutes of sensing
below the set threshold
!
76
*When selected for use with Exterior Rolling Shutter or Exterior Shade
Applications, whereby the window covering is mounted externally to the
window and Thermo Sunis sensor, the window covering will travel to
location of sensor only. It is suggested that (Mode 1) is used to command
no more than (1) window covering per sensor
!
*When selected for use with Interior Window Coverings, the Thermo
Sunis sensor will provide RTS commands to preset window covering
limits
=
(Go to DOWN Limit)
=
(Go to UP Limit).
Activation of Window Covering Via:
Temperature & Sunlight
!
When
(Sun & Temperature) control is selected, the Temperature
threshold setting will TAKE PRIORITY over the Sun Threshold Setting.
!
Sun Activation (control via sunlight) is not possible unless temperature
is within the preset threshold.
Momentarily press the Mode Button, sun & temperature LED Indicator
light will illuminate (for approximately 15 seconds) to indicate
preset (threshold) sensor status.
GREEN LED: INDICATES SENSOR WITHIN THRESHOLD SETTING
RED LED: INDICATES SENSOR BELOW THRESHOLD SETTING
!
The Thermo Sunis RTS Sensor is capable of providing control
in accordance to sunlight and temperature conditions only. Once a
command is sent, the Thermosunis will not send another command
until there is a change in sunlight or temperature conditions.
Replacing the battery
Refer to Sunis Indoor Figure 4, pg. 70.
Programming Figures
ON/OFF
Selector Switch
FIGURE 1
Sun LED
Indicator
Programming
Button
Control
Setting
Panel
Rear Cover
77
QUICK PROGRAMMING FOR THERMO SUNIS INDOOR WIREFREE SENSOR
Programming Figures
FIGURE 2
Window
Glass Mount
Window
Sill Mount
ON/OFF
Sun/Temp
Selector Switch
FIGURE 3
Sun LED
Indicator
Temperature
LED
Indicator
* Sun
Sensitivity
(Threshold)
Selector
* Temperature
Sensitivity
(Threshold)
Selector
Mode Button
Control
Setting Panel
Function Selector
Switch
123
Command Modes
Note: Sensitivity Threshold
(-) less sunlight (+) more sunlight
FIGURE 4
Rear
Cover
Sensor Case
Control
Setting
Panel
78
QUICK PROGRAMMING FOR EOLIS 3D WIREFREE™ WIND SENSOR
BEFORE YOU BEGIN
Make sure the "DOWN" button on
the remote extends the awning.
If this is incorrect please refer to relevant
motor/receiver instructions to revearse the
direction of operation for the awning.
Failure to correct this error will cause
damage to awning by extending
it during windy conditions.
Awning
Awning
Front Bar
Eolis 3D
ADDING BATTERIES
Clear awning of any debris
and make sure surface of awning is clean.
Apply tape and secure mounting plate to front bar of awning.
Adding Batteries
STEP 1: Remove the sensor
housing using a small screwdriver.
Red
Light
STEP 2: Install 2 AAA alkaline
batteries (included). Make sure
the red light blinks. If red light
does not blink, check batteries
for correct polarity.
PROGRAMMING MODE
Pen
Programming
Button
STEP 1: Press the PROGRAMMING
BUTTON on the back of the remote
until the awning jogs.
STEP 2: Press the PROGRAMMING
BUTTON on the Eolis 3D Sensor
until the awning jogs.
Programming
Button
79
QUICK PROGRAMMING FOR EOLIS 3D WIREFREE™ WIND SENSOR
STEP 3: Adjust the sensor dial to (4).
(1= Most sensitive, 9= Least sensitive)
STEP 4: Put the sensor electronics
back in the housing.
STEP 5: Slide the housing back on
the mounting plate.
STEP 6: Test the sensor by pushing up
and down on the awning front bar or
arm until it begins to retract. You
can use the remote to stop the
awning after 5 seconds (first test mode).
STEP 7 : Bring the awning back out
and test it again. You can use the
remote to stop the awning after 5
seconds (second test mode).
Make adjustments to the sensitivity if needed and test it again.
80
QUICK PROGRAMMING FOR ONDEIS WIREFREE™ RAIN & SUN SENSOR
BEFORE YOU BEGIN
LED Behavior
Normal Operation
Blinks every 5 seconds when conditions are above the threshold
Demo Mode
Alternate blinks when entering demo mode
Blinks continuously when conditions are above the threshold
Blink together when exiting demo mode
NOTE: The sensor does NOT operate under 32°F/0°C; standing
water, snow or frost DOES NOT activate sensor.
Getting Started
Hatch Label
Rain Threshold Dial
Sun Threshold Dial
Demo Button
Programming Button
Configuration Switches
1) Charge the sensor.
a. 10 minutes in direct sunlight will
provide operation charge.
b. For most efficient charging, open
hatch and move all switches to the OFF
position.
Switch Sticker
ON
1
2
3
4
Off - Power Saving
2) Confirm RTS motorized window coverings are operating properly from an RTS
control. The UP command should send the awnings IN and screens/shutters UP.
(To change the direction please follow the awning instructions)
3) Choose sensor operation mode. The default setting is Awning Rain. For
detailed explanations of operation modes, refer to Operation Modes on reverse.
NOTE: A Soliris transmitter (1810647 or 1811243 – not included) is required
for Awning Sun and Awning Rain & Sun operation modes.
81
4) Select sensor threshold settings
a. Factory Default:
Rain: 9 o’clock (arrow pointing left)
Sun: 12 o’clock (arrow pointing up)
ON
A
1
2
3
SUN
Approx 12:00
Facing Sun.
Light Cloud Cover
RAIN
Approx 9:00
Light Rain
4
Awning Rain
b. More sensitive: turn left
Very light rain/heavy mist/heavy condensation
Heavy cloud cover (.5 klux)
c. Less sensitive: turn right
Very heavy rain
Direct summer sun, no cloud cover (55 klux)
RAIN
5) Program the sensor to the motor(s)
Step 1: Press the programming button on the RTS transmitter to put the motor
into programming mode – motor will jog.
Step 2: Press the sensor’s programming button – motor will jog again.
Programming Button
Demo Button
6) To confirm settings, put sensor into demo mode to test rain/sun sensing
without standard wait times.
a. Briefly press and release “Demo” button. The associated motor(s) will jog
and the sensor’s LEDs will alternate blinks.
b. Demo mode will time out after 2 minutes. To exit demo mode, press the
Demo button again.
Sensor Time Delays
Rain present
Rain absent
Sun present
Sun absent
82
DEMO MODE
NORMAL MODE
0 sec (Up-Unlocked)
3 sec (Unlocked)
10 sec (DOWN)
15 sec (UP)
0 sec (Up-Locked)
5 min (Unlocked)
2 min (DOWN)
15-30 min (UP)
7) Mount the sensor for maximum exposure to rain and/or sun.
a. For best sun protection, sensor should be mounted facing same
direction as the associated motorized window coverings.
b. For best rain protection, sensor should be exposed to as much rain as
possible.
c. There are three different mounting options possible using included
mounting plate and bracket: vertical mount, pole mount (using zip ties,
not included) and gutter mount.
Pole and Wall Mount
The mounting bracket is released by pushing the bracket clips down gently
towards the main body of the sensor and sliding out the mounting bracket.
To replace the mounting bracket, press the bracket clips down gently towards
the main body of the sensor and slide in the mounting bracket, making sure
the front tabs move into the top slot and the back tabs into the lower slot.
Gutter Mount
Securely attach rain sensor
mounting plate to aluminum
gutter mount bracket using flat
head screws and nylon locking
nuts. Slide gutter mount bracket
over gutter lip and secure with
socket-head screws.
NOTE: If the sensor is removed from a job site, it must be deleted from
the motor’s memory. If the sensor is removed from the jobsite while in
a sensor mode, the awning will retract at regular intervals.
The sensor must also be deleted from the motor’s memory before
switching between awning and shutter/screen modes.
83
Operation Modes
Important: A programmed sensor must be deleted from the motor’s memory
before it is changed between Awning or Shutter/Screen mode. Do not change
between Awning and Shutter/Screen modes without deleting the sensor from
the motor’s memory first (to delete the sensor see step 5 on page 82).
Awning Modes (Sensor Modes):
A. Awning Rain (factory default)
Rain over threshold: sends awning in
Awning is locked until 5 minutes after last rain
over threshold detected
NOTE: Standing water, snow or frost DOES NOT
lock the sensor.
B. Awning Sun
NOTE: A Soliris transmitter (1810647 or
1811243 – not included) is required to activate
the motor’s sun function.
Sun over threshold (for 2 minutes): sends
awning out
Sun under threshold (for 15-30 minutes):
sends awning in
C. Awning Rain & Sun
NOTE: A Soliris transmitter (1810647 or 1811243
– not included) is required to activate the
motor’s sun function
Rain over threshold: sends awning in
Awning is locked until 5 minutes after last rain
over threshold detected, even to Sun commands
awning out
Rain & Sun over threshold: sends awning in
Rain & Sun under threshold (for 15-30
minutes): sends awning in
D. Awning Sensor Test
Allows testing of the sensor programmed to the
motor. In this mode, pressing the DEMO button will
extend the awning. This mode is for testing only. Do
not leave the unit in this mode for normal
operation.
84
ON
A
1
2
3
4
Awning Rain
ON
B
1
2
3
4
Awning Sun
ON
C
1
2
3
4
Awning Rain & Sun
ON
D
1
2
3
4
Awning Sensor Test
Operation Modes
Shutter/Screen Modes (Transmitter Modes):
Remove switch sticker to access shutter settings
E. Shutter/Screen Rain
Rain over threshold: sends shutters/screens
down
Rain doesn’t lock the motor – transmitter
commands will still work.
Will not send another command until rain falls
below the threshold for 5 min and then goes
above again
F. Shutter/Screen Rain & Sun
Rain over threshold: sends shutters/screens
down
Shutter/screen will lock out sun commands until
5 minutes after last rain over threshold is
detected; transmitter commands will still work
shutters/screens down
Sun under threshold (for 15 minutes): sends
shutters/screens up
G. Shutter/Screen Rain & Auto Up
Rain over threshold: sends shutters/screens down
Rain doesn’t lock the motor – transmitter
commands will still work
Rain under threshold (for 5 minutes): sends
shutters/screens up
H. Shutter/Screen Transmitter Test
Allows testing of the sensor programmed to the
motor. In this mode, pressing the DEMO button will
send a down transmitter command. This mode is for
testing only. Do not leave the unit in this mode for
normal operation.
ON
E
1
2
3
4
Shutter/Screen Rain
ON
F
1
2
3
4
S/S Rain & Sun
ON
G
1
2
3
4
S/S Rain & Auto
ON
H
1
2
3
4
S/S Transmitter Test
85
QUICK PROGRAMMING FOR TELIS 16 RTS
DESCRIPTION
The Telis 16 RTS remote control allows you to control up to 16 end-products
or groups of end-porducts using Radio Technology Somfy (RTS)
BEFORE YOU BEGIN
We recommend that each motor is programmed in advance using an
individual Telis 1 RTS transmitter and that the limits of each
motor are set. However, like any RTS remote control transmitter, the
Telis 16 RTS can be used for motor programming operations
(limit switch adjustment, etc.)
After 2 minutes of inactivity, the Telis 16 RTS screen automatically goes
to SLEEP MODE. When the screen is off, first press any button to turn it on.
Naming a Channel
STEP 1: Select the channel you want to customize using the arrow
buttons or .
STEP 2: Press and hold the SELECTION button ( ) until SET
appears on the screen SET MODE is activated. The flashing icon
(shades/shutter, rolling shutters/skylight shades and awning)
are displayed. Use ARROW buttons and to scroll through
the choices.
Selection button
STEP 3: Briefly press the SELECTION button ( ) to save the icon displayed and
move to the first character.
STEP 4: Select the location of the character to be edited using the navigation
buttons or . The flashing hyphen corresponds to the character to be edited.
STEP 5: Briefly press the SELECTION button ( ) to edit the character in this location.
STEP 6: The character flashes to select another character, press the ARROW
buttons or .
86
QUICK PROGRAMMING FOR TELIS 16 RTS
STEP 7: Briefly press the SELECTION button to save the character displayed and
move to the next character.
STEP 8: Repeat steps 4 to 7 for each of the characters in the channels name.
STEP 9: Press and hold the SELECTION button until SET is no longer displayed on
the screen SET MODE is deactivated, and the Telis 16 Chronis RTS returns to
MANUAL MODE.
!
The characters (7 letters +1 number) can be alphabetic (A to Z) or
numeric (0 to 9)
!
Naming Other Channels: Repeat steps 1 to 9 for each channel you want
to customize.
Adding or Deleting Transmitter/Channel
!
The procedure for assigning window coverings to the channels of the
Telis 16 RTS and deleting them is identical.
STEP 1: Press and hold the PROGRAMMING BUTTON on the individual RTS
transmitter that has already been programmed until the window coverings
jogs: PROGRAMMING MODE is activated for 2 minutes.
STEP 2: Use the ARROW buttons or
RTS to be programmed.
to select the channel on the Telis 16
STEP 3: Briefly press the PROGRAMMING BUTTON on the Telis 16 RTS. The
window coverings jogs back and forth and it is assigned to or deleted from
the chosen channel on the Telis 16 RTS.
!
In order to assign or delete the window covering from other channels,
repeat steps 1 to 3, selecting another channel.
87
QUICK PROGRAMMING FOR TELIS 1 CHRONIS RTS
Description
®
The Telis 1 Chronis RTS combines the functionality of a single
channel RTS hand-held control with the convenience of a
programmable timer. This new control option is compatible with
all Radio Technology Somfy® (RTS) motorized applications and offers simple
programming and easy operation.
Main Functions
The timer function has 2 commands / day:
One up & one down (default up @ 7:30 am & down @ 8:00 pm).
2 possible schedules:
Daily schedule - same cycle everyday.
Weekday & Weekend schedule: 2 UP
and DOWN times (1 for weekdays & 1
for weekends).
Quick Set function: A simple press and
hod of the UP or DOWN button for 11
seconds saves the current time as the
opening or closing time of motorized
applications every day.
Vacation mode: Varies scheduled time to
simulate a lived in look (randomly opens
and closes from 0 to + 30 minutes).
Additional Functions
Pre-programmed in factory : Daily programming : Up at
7:30 am /DOWN at 8:00 pm.
Ability to manually modify scheduled times via selection
button & navigation keys.
Automatic adjustment for daylight savings time.
Low battery indication - customers are notified when
batteries need replacing (AAA batteries).
88
Set-up
Before using the Telis 1 Chronis RTS, all motor limits must be set
and fully operational with another RTS transmitter.
!
After 2 minutes of inactivity, the Telis 1 Chronis RTS screen switches to sleep
mode. Press any button to turn it back on.
Battery Installation
Remove the battery cover from the back of the
Telis 1 Chronis RTS and insert included 2 AAA
(LR3) batteries following the polarity
indicated.
Replace the cover.
Turn on the Telis 1 Chronis RTS by briefly
pressing any button.
Replace the batteries when the
symbol appears on the display. Never
use Rechargeable batteries.
!
If there is no power supply for an extended period of time (batteries are
discharged or removed), the general parameters of the remote will need to
be reset. However, the automatic schedules are saved in memory.
89
Setting the General Parameters
When the batteries are first installed, the transmitter will enter programming
mode. “SET” and “YEAR” appear on the screen, with the year flashing.
Press the arrow buttons ( or ) to modify the parameter. The parameter to
be set will be flashing (press and hold the button to scroll the characters
faster).
To save the parameter and move to the next parameter, briefly press the
selection button ( ).
To access and modify the general parameters press and hold the selection
!
button ( ) for 7 sec until the screen displays “YEAR”.
The parameters appear in the following order:
1
2
Current year
Number of
current month
3
4
5
Number of
current day
6
Minutes
Current hour
Daily/Weekend
Country of
residence
8
7
Daily/Weekend
US
4s
Confirms last
parameter
Select the work/daily days you want to program using the arrow buttons
( or ). All days are work days unless deselected. To deselect a day
briefly press and release the selection button ( ).
!
90
Press and hold the selection button ( ) to exit programming mode at
any time.
Adding or Deleting a Telis 1 Chronis RTS
!
The procedure for assigning an end-product to the Telis 1 Chronis RTS
and deleting it is the same.
STEP 1: Using a paperclip or pen, press and hold the PROGRAMMING
BUTTON on a previously addressed RTS Transmitter until the window
covering jogs.
!
Step 1 should not be performed with the Telis 1 Chronis RTS
intended for deletion.
STEP 2: Select the Telis 1 Chronis RTS (single channel) to be added
or deleted.
STEP 3: Press and hold the PROGRAM BUTTON on the Telis 1 Chronis RTS
until the window covering jogs. The Telis 1 Chronis RTS is now added or
deleted from the window covering memory and will now operate the
window covering.
Telis 1 Chronis RTS programming is now complete. The programmed window
covering will now automatically activate at the pre-programmed UP and
DOWN times of 7:30am and 8pm respectively.
91
Editing Pre-programmed Schedules
Schedule Quick Set
The Quick Set feature allows users to change schedule activation
UP and DOWN times to the current time of day.
STEP1: Press the arrow buttons (< or >) to select the (UP) or (DOWN)
time you wish to edit.
STEP 2: Press and hold the ( UP) to modify the UP time or
( DOWN) to modify the DOWN time for 11 seconds.
The word SET will appear and the schedule time will change
to the current time and start to flash.
STEP 3: The word SET will disappear. Release the ( UP) or
( DOWN) button. The new schedule time is now saved.
!
92
Do not release the ( UP) or ( DOWN) button until the
word SET disappears or the new schedule will not be saved.
Editing Schedules
1. Press the arrow keys (< or >) to select the
time you wish to edit.
2. Press and hold the selection button ( )
until the word EDIT appears and flashes.
3s.
3. Press the selection button ( ); the hour
will flash.
4. Use the (< or >) button to set the hour.
5. Press the selection button ( ) to confirm
the hour;the minutes will flash.
6. Use the (< or >) buttons to change the
minutes.
7. Press the selection button ( ) to confirm
the time. The new activation time is now saved.
Deleting an Activation Time
1. Press the arrow keys (< or >) to select the
time you wish to delete.
2. Press and hold the selection button ( )
until the word EDIT appears and flashes.
3s.
3. Press either (< or >) button until DELETE
appears.
4. Press the selection button ( ) to delete
selected activation time and to confirm
changes.
Vacation Mode
Vacation mode varies schedule times to simulate a lived-in look
(randomly opens and closes window coverings from 0 to 30
minutes from the set activation time).
- To activate or deactivate Vacation Mode, press and hold both
(< and >) until the (
) symbol appears or disappears.
93
TROUBLESHOOTING RTS MOTORS
BEFORE YOU CALL FOR SERVICE:
Verify the motor is powered
Verify the motor is installed correctly inside the tube
(Crown & Drive correctly installed)
Verify the motor limits are set correctly
Allow time for motor to cool off after continuous operation
(we recommend at least 15 min) (motors are equipped with a
thermal shut off for safety).
Verify all sensors on location are within RTS range and are working properly
Check the transmitter batteries (LED should flash with a button press)
Verify that the transmitter you are using is properly programmed into
the motors memory
Do not cut power cable shorter than 12 inches (the power cable acts as
an antenna)
The mounting distance between 2 motor heads must exceed 19 inches
to avoid radio interference.
Verify there is no outside radio interference on location (some examples
would be airports, marinas, army bases, weather or security systems.
In PROGRAMMING MODE and LIMIT ADJUSTMENT MODE the radio reception
of the motor is reduced. It is necessary to move the transmitter closer to
the motor head during this time.
Please visit the technical support section of www.somfysystems.com or call
Somfy Customer Service at 877-22-SOMFY
NOTES
94
NOTES
95
SOMFY SYSTEMS INC
SOMFY NORTH AMERICAN HEADQUARTERS
121 Herrod Blvd.
Dayton, NJ 08810
P: (800) 22-SOMFY (76639)
NJ: (609) 395-1300
F: (609) 395-1776
SOMFY ULC
SOMFY Canada Division
5178 Everest Drive
Mississauga, Ontario L4W2R4
P: 1-800-66-SOMFY (76639)
CN: (905) 564-6446
F: (905) 238-1491
www.somfysystems.com
© Copyright Somfy Systems, Inc. 9/2015
CALIFORNIA
15291 Barranca Parkway
Irvine, CA 92618-2201
P: (800) 22-SOMFY (76639)
F: (949) 727-3775
L-0156
FLORIDA
6100 Broken Sound Pkwy. N.W.
Suite 14
Boca Raton, FL 33487
P: (800) 22-SOMFY (76639)
F: (561) 995-7502

RTS Pocket Programming Guide

Transcription

Similar documents

Untitled - Brookstone

Untitled

MusicParts.Com

Flatbed

Q_893MAX 890MAX

XMPlayer Express

T-REX Manual - RC Helitechnics

Hotmail/Live/ MSN/Outlook.com