HUAWEI HG622 -- HUAWEI Home Gateway

Huawei HG622 -- HUAWEI
Home Gateway
STATUS
Device
xTM
WAN
LAN
WLAN
Device
This page displays the device information, such as Product type, Device ID, Hardware version, and Software version.
XTM
This page displays the xTM statistics, such as Tx Bytes Count, Rx Bytes Count, Tx Packets Coun, Rx Packets Count, and Cell
Errors.
1
kochise.com.es/wordpress
WAN
Network: This page displays the information about WAN connections, such as Status, Online Duration, IP Address, and DNS
Information.
DSL: This page displays the upstream status of the DSL, such as Connection Status and Line Status.
a. The connection status shows whether the DSL connection is set up. Showtime indicates that the connection is set up
successfully. Idle indicates that the DSL is in the idle state.
b. The line status shows the statistics of the connected DSLs.
Ethernet:This page displays the upstream status of the Ethernet, such as Status, Rate, and Mode.
UMTS: This page displays the upstream status of the UMTS, such as Maximum upstream rate, Maximum downstream rate,
Signal strength, Service status, Service domain, System mode, and SIM card status.
2
kochise.com.es/wordpress
LAN
This page displays the interface and connection information about the Ethernet LAN and WLAN.
• Network Information: The maintenance information on the LAN side displays the gateway IP address and MAC address.
• Ethernet Interface Information: The Ethernet interface information shows the status of each LAN interface, packet
sending and receiving status, and number of bytes.
a. The port status shows the LAN port to which the terminal is connected.
b. The connected device type shows the terminals connected to the gateway, such as the PC, STB, camera, and IP
telephone.
c. The Ethernet packet statistics shows the statistics of the packets transmitted through the LAN port.
3
kochise.com.es/wordpress
WLAN Information
a. WLAN Status: It displays Status and Channel of the WLAN.
b. Security Settings: It displays SSID index, SSID, Authentication Mode, and Encryption Mode of the WLAN.
c. Wireless Packet Statistics: It displays the packet statistics of each SSID, including the number of received bytes, sent
bytes, packets, error packets, and discarded packets.
4
kochise.com.es/wordpress
BASIC
DSL
Link Interface
WAN
LAN
WLAN
DSL
DSL modulation type is offered for choose, they ar G.Dmt,ADSL2 ,ADSL2+,T1.413 ,VDSL2 .You can select one or more of
them. If ALL is selected, then the gateway supports all of them.
Link Interface
On this page,you can configrue the status of ATM,the value of VPI/VCI and select the path,at same time,you can set the
status of VLAN,the model of encapsulation and the service type.
5
kochise.com.es/wordpress
WAN
The WAN connection manages the WAN interfaces and addresses. Thus, the gateway can access the WAN. The parameters
are described as follows:
- Access Type: It displays the physical interfaces associated with the WAN connection, such as the DSL, Ethernet, and UMTS.
- Service list: It is the service type carried by the WAN connection. You can select INTERNET, TR069, VOICE, or any
combination of the preceding three types.
- Virtual channel: It is the logical link when the access type is the DSL. You can configure up to four virtual channels and
configure up to four WAN connections for each virtual channel.
- VLAN: It is the logical link when the access type is the Ethernet. You can configure up to four VLANs and configure up to
four WAN connections for each VLAN. When the access type is the DSL, you can also configure the VLAN. It indicates
whether the packets sent from the WAN connection contain the VLAN identifier.
- Port binding: It is used to specify which LAN ports and WLAN ports are bound to the WAN connection. The bound LAN
ports and WLAN ports can access the network through only the designated WAN connection.
- Connection mode: It is used to specify whether the WAN connection is in routing mode or in bridge mode. In routing
mode, the IP address needs to be set or is set to be obtained automatically for the WAN connection. In bridge mode, the IP
address needs to be set or is set to be obtained automatically only on the LAN side.
- Connection type: It is the interface encapsulation type managed by the WAN connection. When the access type is the DSL,
the gateway supports five routing modes: PPPoE, PPPoA, DHCP, Static, and IPoA and two bridge modes: IP_Bridged and
PPP_Bridged. When the access type is the Ethernet, the gateway supports three routing modes: PPPoE, DHCP, and Static
and two bridge modes: IP_Bridged and PPP_Bridged. When the access type is the UMTS, the gateway supports only the
PPP-type routing mode.
- DHCP transparent transmission: It is used to specify whether to perform the DHCP transparent transmission in bridge
mode. If transparent transmission is set, the LAN devices can obtain the addresses of public networks through the bridge.
Otherwise, the devices can obtain only the addresses of private networks assigned by the gateway.
- NAT: It is used to specify whether to perform the IP address translation in routing mode. Through NAT, the LAN IP address
can be translated into WAN IP address. Thus, the LAN devices with the IP addresses of private networks can access the
network.
6
kochise.com.es/wordpress
- NAT type: It is the NAT type. You can select NAPT or Cone NAT. If you select NAPT, one-to-one translation is performed
between the LAN device and the public network. This translation is of high security. If you select Cone NAT, one-to-many
translation is performed between the LAN device and the public network. This translation is of low security, but is easy for
network communication.
- User name: It is the user name used for identity authentication when the connection type is set to PPPoA, PPPoE, or PPP.
- Password: It is the password used for the password authentication when the connection type is set to PPPoA, PPPoE, or
PPP.
- DHCP spoofing: When the connection type is set to PPPoA, PPPoE, or PPP, if this function is enabled, the IP addresses
obtained from the WAN connection can be allocated to LAN devices through DHCP. Thus, for the LAN devices, a PPP
network is regarded as a DHCP network. The advantage is that the LAN device does not need to be installed with a dial-up
client when it obtains the addresses of public networks.
- Authentication mode: It is the authentication mode when the connection type is set to PPPoA, PPPoE, or PPP. The RAP,
CHAP, and Auto modes are supported.
- Dialing method: It is the dialing method when the connection type is set to PPPoA, PPPoE, or PPP. The auto, manual, and
on-demand dialing methods are supported. When the auto dialing method is selected, if the upstream link associated with
the WAN connection is available, the gateway automatically starts dialing. If the dialing fails, the gateway retries
automatically after an interval until the dialing succeeds. When the manual dialing method is selected, you need to
manually start the dialing. If the dialing fails, the gateway automatically retries for another two times. If the dialing still
fails, the gateway stops dialing. To access the network, you need to manually restart the dialing. When the on-demand
dialing method is selected, if the gateway detects that you want to access the network, the gateway automatically starts
dialing. If the network is not accessed during the idle time, the gateway automatically disconnects the dial-up connection.
- Idle time: When the on-demand dialing method is selected, if the network is not accessed during this idle time, the
gateway automatically disconnects the dial-up connection.
- IP address: When the connection type is set to IPoA or Static, you need to manually set the static IP address.
7
kochise.com.es/wordpress
LAN
a) Host Settings on the LAN Side
On this page, you can set the LAN-side parameters of the gateway, including the maintenance address, DHCP server
parameters, access parameters of the WLAN, and MAC filtering parameters.
After you set the IP address and subnet mask of the gateway on the LAN side, you should set the IP address of the host to
be in the same network segment as that of the gateway, or you can configure the host to automatically obtain an IP
address. Thus, the host can access the gateway properly. Assume that the IP address of the gateway is set to 192.168.0.1
and the subnet mask is set to 255.255.255.0. When the IP address of the host needs to be set manually, you need to set the
IP address of the host to 192.168.0.x and set the subnet mask of the host to 255.255.255.0. In this case, the host can access
the gateway properly.
b) DHCP Server Settings
Enable DHCP server: If you enable the DHCP server, the host on the LAN side can automatically obtain an IP address and a
DNS address.
• Parameter settings of the DHCP server:
- The start IP address and end IP address specify the range of IP addresses that can be allocated to the LAN devices by the
primary address pool (default address pool) of the DHCP server.
- The lease duration is specified when the DHCP server allocates an IP address to a LAN device. When the IP address is used
by the LAN device for a period that reaches half of the lease duration, the LAN device should apply for the same IP address
again.
You can select a device type to perform the operations related to the secondary address pool and the DHCP relay.
- The start IP address and end IP address of the secondary IP address pool specify the range of IP addresses that can be
allocated to a certain type of devices. If you do not change this IP address pool, the DHCP server allocates IP addresses
specified by the primary IP address pool by default.
If you enable the DHCP relay, the specified LAN device can use the bridge mode (instead of the routing mode) on the WAN
side of the gateway to automatically obtain an upstream public-network IP address on the WAN side. If you disable the
DHCP relay, the LAN device can automatically obtain only a private-network IP address allocated by the DHCP server in the
address pool.
- The primary DNS server address is obtained by the LAN device when the device is set to automatically obtain an IP
address.
- The secondary DNS server address is obtained by the LAN device when the device is set to automatically obtain the IP
address.
If you set WAN-side address allocation mode to Transparent transmission and the LAN device is set to automatically obtain
the IP address, the DHCP server can allocate the IP addresses obtained from the associated WAN interface to the device
with the specified MAC address. If you do not specify the MAC address, the device can be any device on the LAN side by
default.
If you enable transparent transmission on the DHCP port and select a port on the LAN side, the LAN device can use the
bridge mode (not the routing mode) on the WAN side of the gateway to automatically obtain an upstream public-network
IP address on the WAN side. If you disable transparent transmission on the DHCP port, the LAN device can automatically
obtain only a private-network IP address allocated by the DHCP server in the address pool.
8
kochise.com.es/wordpress
WLAN
WLAN Settings: Enable WLAN: It is used to specify whether to enable the WLAN.
- Mode: It is used to select a working mode of the WLAN. You can select 802.11b, 802.11g, or 802.11b/g (that is the mixed
mode).
- Country code: It is used to select the country where the WLAN works. Then the channel list of the WLAN is generated
based on the country that you set.
- Country: When the country where the WLAN works is not in the country code list, you can enter the abbreviation of the
country in this text box.
- Channel: It is used to select an appropriate channel from the channel list based on the settings of the WLAN. To avoid
signal interference, channels allocated to each AP should be different. You are recommended to select Auto.
- Rate: It is used to select the working rate of the WLAN connection. If you select Auto, the gateway automatically selects
the maximum appropriate rate based on the channel environment.
T- ransmit power: It is the transmit power of the wireless RF module.
- SSID index: It is the index of the current SSID.
- SSID: You can enter any characters. The character string contains at most 32 characters and is case sensitive.
- Maximum number of accessing devices: It is the maximum number of STAs that are allowed to access the current SSID.
You can enter any number from 1 to 128.
- Enable SSID: It is used to specify whether to enable the current SSID.
- Hide broadcast: It is used to specify whether to enable the function of hiding the broadcast of the current SSID. If you
enable this function, the gateway does not externally broadcast the information about the current SSID.
- Enable QoS: It is used to specify whether to enable the QoS function of the current SSID.
- AP isolation: It is used to specify whether to enable the AP isolation function of the current SSID. If you enable this
function, the STAs with the current SSID cannot access each other.
- Enable STA: It is used to specify whether to enable the STA function of the current SSID.
9
kochise.com.es/wordpress
- Security: It is used to specify the security parameter of the current SSID. The gateway supports the open system,
authentication modes, such as WEP, WPA-PSK, and WPA2-PSK, and corresponding encryption modes.
- Enable WPS: It is used to specify whether to enable the WPS function. Restricted by the driver, only the first SSID provides
the WPS function.
- WPSmode: It is used to select the working mode of the WPS between PIN and pbc.
- PIN: If you set the working mode of the WPS to PIN, enter the PIN generated by the client tool.
WLAN MAC Address Filtering
Enable MAC address filtering: It is used to specify whether to enable the function of filtering MAC addresses.
- Filtering mode: It is used to select the mode for filtering the MAC addresses between blacklist and whitelist. If you select
blacklist, the MAC addresses in the blacklist are not allowed to access the gateway. If you select whitelist, only the MAC
addresses in the whitelist are allowed to access the gateway.
- WLAN Filtering: The table displays the MAC addresses added to the list.
- Source MAC address: It is used to specify the MAC address to be filtered. After you enter the MAC address, click Submit to
add the MAC address to the list.
10
kochise.com.es/wordpress
ADVANCED
Routing
Firewall
NAT
DDNS
IGMP
QoS
USB Port
SNTP
CWMP
UPnP
DLNA
FTP
Routing
• Static Routing: To configure static routing, you can add a routing item to the primary routing table. Each routing item
consists of three basic elements, including the destination network address, next-hop address, and local interface. You
need to set Destination network address and Subnet mask. You can specify a next-hop address by setting Default gateway
and a local transmission interface by setting Interface.
• Dynamic Routing: The gateway works in RIP dynamic routing mode. In dynamic routing mode, the gateway periodically
sends (notifies) the information about the local routing table from a specified interface to the neighbor network node, such
as a router, periodically receives the information about the latest routing table from the neighbor network node, and then
updates the local routing table. If you set Operation to Active, the gateway receives the routing table information from the
neighbor network node and also sends the routing table information to the neighbor network node. If you set Operation to
Passive, the gateway only receives the routing table information but does not send the routing table information. The
gateway supports the RIP in version 1 and version 2. You can set Version as required.
11
kochise.com.es/wordpress
Firewall
The firewall function can be classified into six sub-functions: MAC filtering, IP filtering, URL filtering, Application filtering,
DOS attack, and ACL. The firewall level is a common property of the preceding six sub-functions. If you change the setting
of the firewall level, the setting takes effect on all the six sub-functions.
The firewall has seven levels: Disable, Block_All, High, Middle, Low, Standard, and Custom. To disable the firewall function,
you can select Disable. The filtering degree of the firewall decreases in the sequence of Block_All, High, Middle, and Low.
By default, the firewall level is set to Standard. The Other level is a customized level. In other words, you can customize the
firewall level as required.
Current level indicates the firewall level that is set currently. To set the firewall level, select a level from the Firewall level
drop-down list box. If you select Custom, you should name the customized level and submit the settings. Then the
customized level is displayed. You can customize multiple firewall levels.
After selecting a customized firewall level, such as HGW, from the Firewall level drop-down list box, you can set, delete,
and rename the level.
In the conditions of predefined firewall levels (that is, except the customized firewall levels), the rules of all functional submodules are set based on firewall levels.
• MAC Filtering
If you select the MAC filtering check box, the gateway filters the packets transmitted from the source MAC address to the
destination MAC address. Through time control, the MAC filtering can be implemented during a specified period. When
there are multiple filtering rules, you can define the priorities of these rules. When Disable is displayed in Status, it
indicates that the rule is disabled. Accept indicates that the packets that conform to the rule are allowed to pass. Reject
indicates that the packets that conform to the rule are not allowed to pass.
• IP Filtering
If you select the IP filtering check box, the gateway filters the packets transmitted from the port range of the source IP
address segment to the port range of the destination IP address segment. The protocol can be set to TCP, UDP, ICMP, or
any of the combinations. The source IP address segment ranges from the source start address to the source end address;
the source port range is from the source start port to the source end port; the destination IP address segment ranges from
the destination start address to the destination end address; the destination port range is from the destination start port
12
to the destination end port. The interface indicates the direction from which the packet enters. You can define the
kochise.com.es/wordpress
priorities of the filtering rules. When Disable is displayed in Status, it indicates that the rule is disabled. Accept indicates
that the packets that conform to the rule are allowed to pass. Reject indicates that the packets that conform to the rule are
not allowed to pass.
• URL Filtering
If you select the URL filtering check box, the gateway controls the access to Web sites. A URL is the domain name of a Web
site. You can define the priorities of the filtering rules. When Disable is displayed in Status, it indicates that the rule is
disabled. Accept indicates that the packets that conform to the rule are allowed to pass. Reject indicates that the packets
that conform to the rule are not allowed to pass.
• Application Filtering
If you select the Application filtering check box, the gateway controls the access to applications, such as the FTP, SSH, and
Telnet applications, which pass through the gateway. When Disable is displayed in Status, it indicates that the rule is
disabled. Accept indicates that the packets that comply with the rule are allowed to pass. Reject indicates that the packets
that conform to the rule are not allowed to pass.
• DOS Attack
If you select the DOS attack check box, the gateway prevents the DOS attack from the external network to the internal
network. The DOS attack includes the ICMP flooding attack, SYN flooding attack, and ARP attack.
• ACL
If you select the ACL check box, the gateway controls the access from the LAN and the WAN to the gateway. A service type
is the type of an application service. The access direction indicates that the access is initiated from the LAN or the WAN.
The source IP address segment that can access the gateway ranges from the start IP address to the end IP address. The
access control list (ACL) is a whitelist. In other words, all configured rules are allowed to be accessed by default. The general
rule, however, is to reject all the application services in the drop-down list by default.
13
kochise.com.es/wordpress
NAT
• ALG
a) Introduction
On this page, you can enable or disable multiple types of application level gateways (ALGs), such as the H.323 ALG, PPTP
ALG, and L2TP ALG.
b) Settings
You can enable or disable the PPTP ALG.
You can enable or disable the IPSec ALG.
You can enable or disable the H.323 ALG.
You can enable or disable the L2TP ALG.
You can enable or disable the RTSP ALG.
You can enable or disable the SIP ALG.
• DMZ
a) Introduction
If the demilitarized zone (DMZ) is enabled, the packets that are sent from the WAN and that cannot match any rule are sent
to the computer on the LAN side for analysis or other uses, before the packets are discarded by the firewall.
b) Operation
For each WAN connection, you need to enter the IP address of the specified computer on the LAN side. Then enable the
DMZ connected to the WAN.
- Host address: It is the IP address of the specified computer on the LAN side.
- Enable DMZ: It is used to specify whether to enable the DMZ of the WAN connection.
14
kochise.com.es/wordpress
• Port Mapping
a) Introduction
When NAT is enabled on the gateway, only the IP address on the WAN side is visible externally. When certain services, such
as the FTP service, need to be enabled on a computer on the LAN side, the WAN-side port of the gateway needs to be
redirected to the FTP port of the computer on the LAN side. Thus, the host on the WAN side can access the host on the LAN
side through this WAN-side port.
b) Operation
You can select between two types of port mapping, that is, Customization and Application.
For both types of port mapping, you should enter the IP address of the host on the LAN side. In other words, you need to
specify the LAN-side host to which the services are mapped through the WAN-side port.
- Interface: It is the interface name of the WAN connection.
- Protocol: It is the protocol, such as TCP and UDP, supported by port mapping.
- External port: It is the source port number used by the external network.
- Internal port: It is the destination port number used by the internal network.
- Internal host: It is the LAN-side host IP address to which the port is mapped. It is mandatory to set this parameter.
- External source IP address: It is optional to set this parameter. If you enter the IP address, it indicates that only the WANside host with this IP address can be mapped to the LAN-side host through the port.
- Mapping name: It is mandatory to set this parameter.
15
kochise.com.es/wordpress
• Port Triggering
a) Introduction
For certain P2P-type applications, when a LAN-side computer, such as computer1, connects to the port (called trigger port)
of another computer, such as computer2, or a server, the application opens other ports (called open ports) of computer1
for the connection to computer 2 or other computers, thus implementing the sharing services and P2P-related services.
b) Operation
You can select between two types of port triggering, that is, Customization and Application.
For both types of port triggering, it is mandatory to set Trigger start port, Open start port, and Trigger name.
It is optional to set Trigger end port and Open end port.
16
kochise.com.es/wordpress
DDNS
When the IP address of the WAN interface is changed, the gateway automatically updates the relation between the domain
name and the IP address. Thus, users of the external network can obtain the WAN interface address of the gateway
through the domain name. The parameters are described as follows:
- Service provider: It is the service provider that provides the services for updating dynamic domain names.
- WAN connection: It is used to set up a relation between the domain name and the IP address of the WAN connection.
- Domain: It is the domain specified by the domain-name service provider and is one part of the domain name.
- Host: It is the only name in the specified domain. It can be applied for from the domain-name service provider and is one
part of the domain name.
- User name/Email: It is the identity used to apply for the domain name. During the dynamic update of the domain name,
the identity needs to be verified.
- Password: It is the password used to apply for the domain name. During the dynamic update of the domain name, the
password needs to be authenticated.
- Server address: It is the server address of the domain-name service provider.
- Server port: It is the server protocol port of the domain-name service provider.
- Protocol: It is the server protocol of the domain-name service provider.
IGMP
Through the IGMP snooping function, the gateway performs the multicast management in the link layer and the packets
that have multicast destination MAC addresses can be forwarded to the corresponding host or device.
Through the IGMP proxy function, the gateway performs the multicast management in the network layer and a channel of
multicast stream can be allocated to multiple hosts and devices, thus saving the network bandwidth.
17
kochise.com.es/wordpress
QoS
When the bandwidth is limited, through the QoS function, the gateway can allocate all the bandwidth to a certain
application, increase the priority of the application.
• Global Settings
On this page, you need to set certain global parameters of the QoS. The parameters are described as follows:
- Enable: It is used to specify whether to enable the QoS function.
- Bandwidth: It is used to specify the bandwidth used for the QoS.
- Queue type: It is used to select a policy used for the QoS. The available types are described as follows:
o PQ: If you set Queue type to PQ, four queues are listed based on the priorities. The priority is classified into the
highest priority, high priority, medium priority, and low priority. The gateway first schedules the queue with a
higher priority. If the queue with a higher priority has a packet cache, the queue with a lower priority cannot be
scheduled.
o WFQ: If you set Queue type to WFQ, four queues are listed. You can set the weight of the bandwidth occupied by
each queue. The bandwidth is allocated to each queue based on the corresponding weight.
o WFQ,PQ: If you set Queue type to WFQ,PQ, fore queues are listed. The first queue has the highest priority, The
other queues scheduled by WFQ.
Note: The templates have certain preset classification rules. After you select a template, you can modify the parameter
settings of the template.
- Queue: The parameters of the queue vary with queue types. You need to set the queue type in the global settings, and
then set the corresponding queue parameters. For each queue type, all the queues can be enabled or disabled separately.
- Policer: You can limit the rate of stream though configing the policer parameters.
18
kochise.com.es/wordpress
USB Port
• FTP
a) Introduction
On this page, you can configure the FTP client and download history is displayed.
b) Operation
The gateway can be used as an FTP client and you can set the client parameters.
- User name: It is the user name used to log in to the FTP client.
- Password: It is the password used to log in to the FTP client.
- Download URL: It is the path of the files to be downloaded from the server by the FTP client.
- Port: It is the download port of the FTP client. The default value is 21.
- Device: It is the USB device of the FTP client.
- Local path: It is the local path of the files downloaded by the FTP client.
19
kochise.com.es/wordpress
c) Records
- Download History: It is the download history of the FTP client.
- User Name: It is the user name used to log in to the FTP client.
-Port: It is the download port of the FTP client.
- Download URL: It is the path of the files to be downloaded from the server by the FTP client.
- Local Path: It is the local path of the files downloaded by the FTP client.
- Status: It indicates whether the files are downloaded successfully or not.
• Samba
a) Introduction
You can choose to enable or disable the Samba server. When the Samba server is enabled, you can view, add, and delete
the currently valid information of a Samba user.
b) Operation
Enable Samba: It is used to specify whether to enable the Samba server. To enable the Samba server, select this check box.
To disable the Samba server, cancel the selection of this check box.
- Add Samba User: It is used to add a Samba user.
-Remove: It is used to remove the currently valid information of a Samba user.
- User name: It is the name of the new Samba user.
- Password: It is the login password of the new Samba user.
- Directory: It is the file directory that can be operated by the new Samba user.
- Right: It is the right for the new Samba user to operate the directory. The right is classified into two types: Read only and
Readable and Writable.
• Printer Server
1. Introduction
This application notes explain the steps of enabling the Printer Server function in HUAWEI DSL Router Home Gateway
platforms.
2. How to enable on-board Printer Server function -- Following are the steps to enable the on-board Printer Server.
20
kochise.com.es/wordpress
Step 1: Click on Add a printer from Control Panel of the Win XP computer and click "Next".
Step 2: Select Network Printer and click "Next".
Step 3: Select Connect to a printer on the Internet, type "http://192.168.1.1:631/printers/hp3845" and click "Next".
The printer name "hp3845" can be any name you liked.
Step 4: Click "Have Disk", insert printer driver CD.
Step 5: Select driver file directory on CD-ROM and click "OK".
Step 6: Once the printer name appears, click "OK".
Step 7: Choose "Yes" or "No" for default printer setting and click "Next".
Step 8: Click "Finish".
Step 9: Check the status of printer from Windows Control Panel, printer window. Status should be shown ready.
SNTP
The network time synchronization function is used to update the time periodically from the network server so that the local
time can remain the same as the network time. The parameters are described as follows:
- Time server: network server used to update the time. Time server 1 is the primary server, Time server 2 to 5 are
secondary servers, which used to update the time when the primary server doesn't work. You can select the domain of
time server from the combo box or define it by yourself.
- Time zone: The network time is unique. The local time needs to be calculated based on the time zone. Countries and areas
have their own time zones. You can select a time zone from the list.
21
kochise.com.es/wordpress
CWMP
• TR069
The automatic configuration server (ACS) configures the terminal through the WAN management protocol (TR069) of the
CPE. The configuration information includes the dynamic server delivery, status and capability monitoring, and remote
diagnosis. After setting the parameters, click Submit to enable the remote management function.
• TR111
TR111 is an expansion of TR069 through two mechanisms. These two mechanisms increases the capability of the ACS to
remotely manage the LAN-side devices of the home gateway. You need to set the parameters on this page to configure the
STUN server. Through the communication between the gateway and the STUN server, the gateway finds the upstream NAT
devices so that the remote ACS can manage the gateway properly.
22
kochise.com.es/wordpress
UPnP
• Status Display
On this page, you can specify whether to enable the UPnP function.
• Operation
It is used to specify whether to enable the UPnP function. To enable the UPnP function, select the check box. To disable the
UPnP function, cancel the selection of the check box.
23
kochise.com.es/wordpress
DLNA
DLNA(Digital Living Network Alliance) is media sharing solution. Set a directory which containing multi-media, pc or mobile
device which support DLNA can access.
FTP
On this page , you can choose to enable or disable the ftp server, set password and user name for ftp server which are used
to log in to the ftp server.
24
kochise.com.es/wordpress
MAINTENANCE
Account
Device
Diagnose
Log
Account
• Operator Maintenance Account
Password settings: After logging in by the operator maintenance account, you can change the password of this account.
The original password needs to be verified. In addition, the password of the user management account can be changed
without verifying the original password.
• User Management Account
User management account settings: After logging in by the user management account, you can change both the user name
and the password of the account. The original password needs to be verified.
Device
• Reboot
It is used to reboot the gateway.
• Restore Default Settings
It is used to restore the default settings of the gateway.
• Multicast Upgrade
If you enable the multicast upgrade function, the gateway can be upgraded by the multicast server. You need to set
Multicast IP address and Multicast port number for the multicast server.
25
kochise.com.es/wordpress
26
kochise.com.es/wordpress
Diagnose
Ping Test: It is used to test the ADSL loop status. Pass indicates that the ADSL loop is available. Fail indicates that the ADSL
loop is not available.
Log
• Enable
It is used to enable or disable the function of writing the logs. If you enable the function, you need to set the level for
writing and displaying the logs, choose to save the logs locally or remotely, and set the IP address and port number of the
remote server on which the logs are saved.
27
kochise.com.es/wordpress
• Displaying Logs
This page displays the log content at the current level.
28
kochise.com.es/wordpress