Cost effective. - Dryvit | External Wall Insulation

Transcription

DRYVIT OUTSULATION AND ROXSULATION
®
®
BARRIER EXTERIOR INSULATION AND FINISHING SYSTEMS
Dryvit’s Outsulation and Roxsulation
are cost effective exterior insulation
and finishing systems (EIFS) suitable
for use on either new construction
or refurbishment projects.
The systems are based on a simple
premise…insulation is more effective
when placed on the exterior of a
building.
By bringing insulation to the outside
of external walls, these barrier EIFS
eliminate thermal bridges; reduce air,
wind and moisture penetration
through the system; stabilise interior
environments and minimise thermal
shock.
Portsmouth University
Baggy House
Bertha James Court
BENEFITS
•
Friendship House
Design freedom. Both systems can be installed over a variety of substrates. Expanded polystyrene (EPS) insulation
is lightweight and can be cut or grooved to various shapes and surface patterns.
efficiency. Outsulation and Roxsulation enable new or existing buildings to meet strict energy efficiency
• Energy
requirements. Heating or cooling costs are demonstrably lower in lieu of other exterior materials.
Dryvit EIFS are formulated to provide the utmost in weather protection, providing a resilient barrier
• Weatherability.
against the elements.
The combination of system components provide unsurpassed long-term durability meeting design
• Durability.
requirements for use in virtually any location.
Dryvit finishes are available in a wide array of textures in both standard and custom colours. Our speciality
• Aesthetics.
finishes enable designers to replicate a variety of real stone or brick finishes from limestone to granite at a fraction
of the cost.
effective. Outsulation and Roxsulation are easily adapted to complex project details. Installation is rapid, and
• Cost
routine maintenance is minimal.
Independently certified by BBA and other international test bodies. Dryvit manufacturing plants are
• Testing.
ISO 9001:2000 certified, demonstrating the highest standards of quality and consistency.
DUK 902
DRYVIT OUTSULATION® SYSTEM:
APPLICATION
A polymer-based barrier external wall insulation system
incorporating EPS 70E grade expanded polystyrene (EPS)
insulation. British Board of Agrément Certificate No. 98/3548
Detail Sheet 2. NBS Specification Clause - M21
Application of the systems are carried out by Specialist Installers
employing operatives who have been trained in the use of Dryvit
materials. In addition Dryvit are committed to providing on site
support to their network of Specialist Installers when called upon.
1. Fixing Method - Genesis adhesive
and/or mechanical fixings
(depending on substrate)
TM
2. Expanded Polystyrene
Insulation
3. Dryvit Reinforcing Mesh Glass Fibre - weight/s
depending on impact
resistance
4. Dryvit GenesisTM or NCBTM
base coat
5. Dryvit PMR finish - from
standard or speciality finish
ranges
DRYVIT ROXSULATION ® SYSTEM:
A polymer-based barrier external wall insulation system
incorporating mineral wool (slab or lamella) insulation.
British Board of Agrément Certificate No. 98/3548
Detail Sheet 3. NBS Specification Clause - M21
1. Fixing Method - GenesisTM adhesive
and/or mechanical fixings
(depending on substrate)
2. Mineral Wool Lamella
or Slab insulation
Details of recommended Specialist Installers are available from
Dryvit UK Ltd.
THERMAL PERFORMANCE
U-value and condensation risk calculations are carried out by Dryvit
upon request to ensure that the correct thickness of insulation is
specified for each project to meet target requirements. U-values
calculations can then be incorporated within the buildings target
SAP calculation.
Thermal resistivity values of insulation
Outsulation - expanded polystyrene - 0.038 W/mK
Roxsulation - mineral wool insulation - 0.036 – 0.040 W/mK
STANDARD DETAILS
Standard details are available for both Outsulation and Roxsulation
systems and can be downloaded from www.dryvit.co.uk.
Dryvit offers a CAD service to produce bespoke details in line with
specific project needs.
FINISHES
Dryvit 100% acrylic finishes contain quartz aggregates of
various sizes and use Dirt Pickup Resistant (DPR) and Proven
Mildew Resistance (PMRTM) chemistry, ensuring the highest
standard of fade resistance and ensuring low maintenance.
The standard finish range is available in five different textures with
over 360 chart colours to select from. If your desired colour is not
available from our standard finish range then we have a colour
matching service that will be sure to satisfy your requirements.
Even the look of natural stone, granite and brick is possible from our
range of speciality finishes.
STANDARD TEXTURE RANGE
3. Dryvit Reinforcing Mesh Glass Fibre - weight/s
depending on impact
resistance
4. Dryvit GenesisTM or NCBTM
base coat
5. Dryvit PMR finish – from
ranges
CUSTOM BRICKTM
LYMESTONETM
TERRANEO ®
SUBSTRATE TYPES
There are many construction materials, which can be utilised as
effective substrates with the Outsulation and Roxsulation
systems on either solid or framed construction. Common substrates
include, in-situ concrete, pre-cast concrete, blockwork, brick, render,
Wimpey No-fines, exposed aggregate panels plus a wide range of
sheathings carried on both timber and light gauge steel stud.
For guidance on substrate tolerance and the correct fixing method to
withstand thermal stresses and wind pressures (including suction) to
satisfy BS 6399: Part 2 please consult Dryvit UK Ltd.
DRYVIT UK LTD
Unit 4 Wren Park, Hitchin Road,
Shefford, Bedfordshire SG17 5JD
Tel: 01462 819555 Fax: 01462 819556
Email: [email protected] www.dryvit.co.uk
Printed in the UK R1: 10/05
©Dryvit UK Ltd. 2005
WARRANTY
•Standard 10 Year “Dryvit Warranty” available on all projects
upon written request.
•10 Year third party insurance backed warranties covering
materials and installation –extended periods available.
•’Back to Back’ warranties available on request from
partnering material suppliers and installers.
For more information on warranties please contact Dryvit UK Ltd.
Or visit our web site www.dryvit.co.uk.
DRYVIT DRYSULATIONTM
BARRIER EXTERNAL WALL INSULATION SYSTEM
Dryvit’s Drysulation is a cost-effective external wall
insulation (EWI) system suitable for use on either new
construction or refurbishment projects. The system is based
on a simple premise…insulation is more effective when
placed on the exterior of a building.
By bringing insulation to the outside of external walls, this
barrier EWI eliminates thermal bridges; reduces air, wind
and moisture penetration through the system; stabilises the
interior environment and minimises thermal shock.
Drysulation has been independently certified for use with
either standard (white) or high performance low lambda
grade (grey) expanded polystyrene (EPS) to meet the
thermal needs of all wall and building types. It also has
a wide range of finish options to suit architectural and
parochial requirements.
Energy Efficiency
Educational / Healthcare
Commercial / Hospitality
Social Housing / Residential
•
•
•
•
•
•
•
Design freedom. Drysulation can be installed over a variety of substrates. EPS insulation is lightweight and can be cut
or grooved to various shapes and surface patterns.
Energy efficiency. Drysulation enables new or existing buildings to meet strict energy efficiency requirements.
The option to incorporate high performance low lambda EPS assists in meeting even the most demanding carbon
management plan. Heating or cooling costs are demonstrably lower compared to other exterior materials.
Weatherability. Dryvit EWI systems are formulated to provide the utmost in weather protection, providing a resilient
barrier against the elements.
Durability. The combination of system components provides unsurpassed long-term durability meeting design
Aesthetics. Dryvit finishes are available in a wide array of textures in both standard and custom colours. Our speciality
finishes enable designers to replicate a variety of real stone or brick finishes from limestone to granite at a fraction of
the cost.
Cost effective. Drysulation is easily adapted to complex project details. Installation is rapid, and routine maintenance
is minimal.
Testing. Drysulation has ETA certification and independent certification from BBA. Dryvit manufacturing plants are ISO
9001 certified, demonstrating the highest standards of quality and consistency.
DUK 912
DRYVIT DRYSULATIONTM SYSTEM
THERMAL PERFORMANCE
A polymer-based barrier external wall insulation system incorporating
U-value and condensation risk calculations are carried out
by Dryvit upon request to ensure that the correct thickness
of insulation is recommended for each project to meet target
requirements. U-value calculations can then be incorporated within
the buildings target SAP calculation.
EPS 70E standard (white) grade or Low Lambda (grey) expanded
polystyrene (EPS) insulation. British Board of Agrément Certificate
No. 98/3548 Product Sheet 4. NBS Specification Clause - M21
Solid Substrates
1. Dryvit DryhesiveTM Plus adhesive and/
or mechanical fixings (depending on
substrate) – fixing method
2. EPS 70 E Low Lambda (Grey) or
standard (White) EPS.
3. Dryvit Reinforcing Mesh – Glass
Fibre – weight/s depending on impact
resistance
4. Dryvit Primus MTM base coat
5. Dryvit HDPTM/Dash/Brick Effect
finishes or other speciality finishes
Framed Substrates
1. Dryvit DryhesiveTM Plus adhesive and/
or mechanical fixings (depending on
substrate) – fixing method
2. EPS 70 E Low Lambda (Grey) or
standard (White) EPS.
Fibre – weight/s depending on impact
resistance
4. Dryvit Primus MTM base coat
5. Dryvit HDPTM/Dash/Brick Effect
finishes or other speciality finishes
Standard (white) EPS - 0.038 W/mK
Low Lambda (grey) EPS - 0.030 - 0.033 W/mK
STANDARD DETAILS
Standard details are available for the Drysulation system and can
be downloaded from www.dryvit.co.uk
FINISHES
High performance Dryvit HDPTM and FD PMR finishes are offered
as the standard with the Drysulation system. HDP textured finishes
incorporate silicone-based technology that promote hydrophobic
properties, which repel water resulting in less dirt pick up and a
cleaner wall appearance. FD PMR finishes are premixed 100%
acrylic finishes containing Dirt Pickup Resistance (DPR), Proven
Mildew Resistance (PMR) technology and a film forming accelerator
for improved resistance to early age wash off. This system is also
certified for use with a wide range of speciality products ranging
from dash, brick effect to natural stone, wood effect and metal
alternatives.
The standard finish range is available
in five different textures with over 360
colours. If your desired colour is not
available from our standard finish
range then we have a colour matching
service that will be sure to satisfy your
requirements.
SUBSTRATE TYPES
STANDARD RANGE - HDPTM
effective substrates with the Drysulation systems on either solid or
framed construction.
Common substrates include, in-situ concrete, pre-cast concrete,
blockwork, brick, render, Wimpey no-fines, exposed aggregate
panels plus a wide range of sheathings carried on both timber and
DASH
BRICK EFFECT
REFLECTITTM
WOOD EFFECT
LYMESTONETM
TERRANEOTM
light gauge steel stud.
For guidance on substrate tolerance and the correct fixing method
to withstand thermal stresses and wind pressures (including
suction) to satisfy BS EN 1991-1-4 please consult Dryvit UK Ltd.
WARRANTY
• Standard 10 Year “Dryvit Warranty” available
APPLICATION
on all projects upon written request.
Application of this system is carried out by Specialist Installers
materials. In addition, Dryvit is committed to providing on site
• 10 - 25 Year third party insurance backed
warranty options available covering
materials and installation.
• ‘Back to Back’ warranties available on
support to the network of Specialist Installers when called upon.
request from partnering material suppliers
and installers.
Details of Specialist Installers are available from Dryvit UK Ltd.
Kinnell
DRYVIT UK LTD
Tel: 01462 819555 Fax: 01462 819556
For more information on warranties please
contact Dryvit UK Ltd. or visit our web site
www.dryvit.co.uk
DRYVIT OUTSULATION PLUS AND
OUTSULATION RAIL
®
TM
MOISTURE DRAINAGE EXTERIOR INSULATION AND
FINISHING SYSTEMS
Dryvit’s Outsulation Plus and Outsulation Rail are
moisture drainage exterior insulation and finishing
systems (EIFS) suitable for use on either new
construction or refurbishment projects. As with
Outsulation® these systems are based on a simple
premise…insulation is more effective when placed on
the exterior of a building.
Due to the increased demands for wall systems to be
able to drain away incidental moisture, Outsulation Plus
and Outsulation Rail have been developed to
incorporate a moisture drainage plane and drained
cavity, respectively.
By bringing insulation to the outside of external walls,
these moisture drainage EIFS eliminate thermal bridges;
stabilise interior environments; minimise thermal shock;
and expand upon the proven weatherability of
Outsulation by adding a second line of defence against
air, moisture and weather.
Harbour Views
BENEFITS
•
Glasgow Harbour
Canning Circus
efficiency. Outsulation Plus and Outsulation Rail enable new or existing buildings to meet strict energy
• Energy
efficiency requirements. Heating or cooling costs are demonstrably lower in lieu of other exterior materials.
Air & Moisture Barrier. Dryvit’s Backstop NT weather-resistive membrane prevents water penetration and eliminates
• air
infiltration. Unlike traditional woven sheet breather membranes it enables adhesive fix of the Outsulation Plus
TM
system and offers a faster and unhindered installation of the Outsulation Rail holding track over sheathed substrates.
Drainage System. Both systems have moisture drainage detailing which will evacuate incidental moisture
• Moisture
that may enter the building envelope at terminations or penetrations.
Dryvit products are formulated to provide the utmost in weather protection providing a resilient barrier
• Weatherability.
• Durability.
• Aesthetics.
of the cost.
effective. Outsulation Plus and Outsulation Rail are adaptable to complex project details. Installation is rapid,
• Cost
and routine maintenance is minimal.
Independently certified by international test bodies. Dryvit manufacturing plants are ISO 9001:2000 certified,
• Testing.
demonstrating the highest standards of quality and consistency.
DUK 903
DRYVIT OUTSULATION® PLUS SYSTEM:
APPLICATION
A high-performance EIFS with a moisture drainage plane
incorporating an air & moisture protective membrane
(where required) and grooved EPS 70E grade expanded
polystyrene (EPS) insulation. NBS Specification Clause - M21
1. Dryvit AquaFlashTM or Flashing TapeTM
to opening terminations
2. Backstop NTTM – air and moisture
barrier to substrate (where
required)
3. GenesisTM adhesive channels
form drainage plane enabling
evacuation of incidental moisture
4. Expanded Polystyrene or Mineral Wool
Lamella Insulation
5. Dryvit Reinforcing Mesh – Glass Fibre –
weight/s depending on impact resistance
6. Dryvit GenesisTM or NCBTM base coat
7. Dryvit PMR finish – from standard or
speciality finish ranges
Dryvit UK Ltd.
THERMAL PERFORMANCE
SAP calculation.
Expanded polystyrene - 0.038 W/mK
Mineral Wool - 0.036 – 0.040 W/mK
STANDARD DETAILS
Standard details are available for both Outsulation Plus and
Outsulation Rail systems and can be downloaded from
www.dryvit.co.uk.
DRYVIT OUTSULATION RAIL SYSTEM TM :
A mechanically fastened rail EIFS, with a drained cavity,
sized to meet project requirements, incorporating an air
& moisture protective barrier (where required) and EPS
70E grade expanded polystyrene (EPS) insulation.
NBS Specification Clause - M21
1. Dryvit AquaFlashTM or Flashing
TapeTM to opening terminations
2. Backstop NTTM – air and moisture
barrier to substrate (where required)
3. PVC holding track rails mechanically
fixed to the substrate. Sized PVC
shims used to create drained cavity
enabling evacuation of incidental
moisture
4. Expanded Polystyrene or Mineral
Wool Insulation – grooved to fit onto
holding track
FINISHES
5. Dryvit Reinforcing Mesh – Glass Fibre –
weight/s depending on impact resistance
7. Dryvit PMR finish – from standard or
speciality finish ranges
SUBSTRATE TYPES
CUSTOM BRICKTM
LYMESTONETM
TERRANEO ®
The Outsulation Plus and Outsulation Rail systems are ideal for use
on lightweight steel or timber framed structures where there is a
requirement for a drainage plane or drained cavity or over solid
substrates in new build or retrofit construction. Outsulation Rail
is also suitable for installation over damaged or brittle substrates
with irregular surfaces.
effective substrates and common substrates include a wide range
of sheathings carried on both timber and light gauge steel stud,
in-situ concrete, pre-cast concrete, blockwork, brick, render,
Wimpey No-fines, and exposed aggregate panels.
satisfy BS 6399: Part 2 please consult Dryvit UK Ltd.S
DRYVIT UK LTD
Tel: 01462 819555 Fax: 01462 819556
WARRANTY
DRYVIT FEDDERLITE AND
®
OUTSULATION CONVENTIONAL PANEL
®
PREFABRICATED EXTERIOR INSULATION AND
FINISHING SYSTEMS
Dryvit’s Fedderlite and Outsulation Conventional Panel
are prefabricated exterior insulation and finishing systems
(EIFS) offering fast track installation for use on either new
construction or refurbishment projects. Like site applied
Outsulation® these prefabricated systems are based on a
simple premise…insulation is more effective when placed
on the exterior of a building.
By bringing insulation to the outside of external walls,
these prefabricated panelised EIFS eliminate thermal
bridges; stabilise interior environments; minimise thermal
shock; and build upon the proven weatherability of
Outsulation.
Dryvit prefabricated systems have a proven track record
fitting well with the Egan philosophy and the ethos of
‘design and build’ procurement. In construction, time
means money. The faster your building is completed, the
earlier it can be occupied and your revenue stream can
start. Ultimately these systems enable building owners to
determine more accurate project costing based on
defined parameters.
Manufacture
Transport
BENEFITS
•
•
•
•
•
•
•
•
•
•
Install
Royal Palm Office Building
Fast track. The panel systems enable rapid installation unhindered by environmental conditions that would normally
affect traditional building methods. Panels can be installed off mast climbers or mobile towers, reducing access time
and cost.
Energy efficiency. Fedderlite and Outsulation Conventional Panel enable new or existing buildings to meet strict
energy efficiency requirements. Heating or cooling costs are demonstrably lower in lieu of other exterior materials.
Lightweight. Panels weigh less than brick, stone or precast concrete thus they limit imposed loading on existing and
new build structures. Despite their lightweight nature the panels are capable of withstanding critical wind and structural
loads.
Versatile. Dimensional adjustments can be made easily and inexpensively right up to panel assembly time. Of great
advantage in retrofit or new build projects.
Weatherability. Dryvit systems are formulated to provide the utmost in weather protection providing a resilient barrier
Durability. The combination of system components provide unsurpassed long-term durability meeting design
Aesthetics. Dryvit finishes are available in a wide array of textures in both standard and custom colours. Our speciality
of the cost.
Cost effective. Fedderlite and Outsulation Conventional Panel are adaptable to complex project details. Installation
is rapid, and routine maintenance is minimal.
Testing. Independently certified by international test bodies. Dryvit manufacturing plants are ISO 9001:2000 certified,
demonstrating the highest standards of quality and consistency.
DUK 904
DRYVIT FEDDERLITE ® SYSTEM:
APPLICATION
A prefabricated EIFS panel system incorporating EPS 70E
grade expanded polystyrene (EPS) insulation. A drainage
cavity can be accommodated in the system if called for in
the specification. NBS Specification Clause - M21
1. Fixing Method – GenesisTM or AP
Adhesive and/or mechanical fix.
(Depending on substrate and cavity
requirements)
2. Channel – this provides a mechanism
for handling and fastening the panel
3. Expanded Polystyrene Insulation
(Mineral Wool please consult Dryvit UK)
4. Dryvit Reinforcing Mesh – Glass Fibre
– weight/s depending on impact resistance
6. Dryvit PMR finish – from standard
or speciality finish ranges
Dryvit UK Ltd.
THERMAL PERFORMANCE
SAP calculation.
Expanded polystyrene - 0.038 W/mK
Mineral Wool - 0.036 – 0.040 W/mK
STANDARD DETAILS
Standard details are available for both Fedderlite® and Outsulation®
Conventional Panel systems and can be downloaded from
www.dryvit.co.uk.
DRYVIT OUTSULATION®
CONVENTIONAL PANEL:
FINISHES
A prefabricated EIFS whole wall panel system incorporating
a lightweight structural steel stud frame, sheathing and EPS
70E grade expanded polystyrene (EPS) or mineral wool
insulation. NBS Specification Clause – H92
1. Lightweight steel frame
2. Sheathing board
3. Expanded Polystyrene or Mineral
Wool Insulation
Fibre – weight/s depending on
impact resistance
6. Dryvit PMR finish – from standard
or speciality finish ranges
CUSTOM BRICKTM
LYMESTONETM
TERRANEO ®
SUBSTRATE TYPES
Fedderlite panels can be installed on wide range or sheathings over
steel or timber frame structures and may be fixed adhesively and/or
mechanically fastened. The panels can also be installed over in-situ
concrete, pre-cast concrete, blockwork, brick, render, Wimpey
No-fines, and exposed aggregate panels.
Outsulation Conventional Panel whole wall panels can be connected
to structural steel or concrete frame structures from inside the
building by welding, bolting, mechanical fasteners or a combination
of fixing methods.
DRYVIT UK LTD
Tel: 01462 819555 Fax: 01462 819556
WARRANTY
DRYVIT ACR AND CEMENT BOARD
MD FINISH SYSTEM
TM
TM
ANTI-CRACK RENDER SYSTEMS
Dryvit ACR systems and the Cement Board MD Finish
System are a range of 100% acrylic polymer based
anti-crack renders designed to out perform the shrinkage
and cracking characteristics of traditional renders. The
range offers a variety of coloured and textured coating
options providing various levels of protection when used
in the different component combinations.
Dryvit ACR systems are generally installed over a Dryvit
polymer modified re-profiling mortar where levelling is
required, on to exterior concrete, brickwork, blockwork,
plastered or painted surfaces in new build or
refurbishment projects.
The Cement Board MD Finish System incorporates an
exterior grade cement board fixed to vertical batons and
is ideal where a cavity system is called for without the
need for exterior insulation. Commonly applied over
timber or steel framed substrates incorporating an
approved sheathing and breather membrane in new
build residential and low-rise commercial projects.
Wellend Villas
Whitefriars
An Sean Mhuillean
BENEFITS
An Sean Mhuillean
resistance. Location and frequency of movement joints is greatly reduced or even eliminated compared with
• Crack
that of traditional renders due to the high performance crack resistance of our systems.
Dryvit systems are formulated to provide the utmost in weather protection providing a resilient barrier
• Weatherability.
against wind and water.
• Durability.
• Aesthetics.
of the cost.
Independently certified by BBA and other international test bodies. Dryvit manufacturing plants are
• Testing.
ISO 9001:2000 certified, demonstrating the highest standards of quality and consistency.
DUK 905
DRYVIT ACR 300:
High performance crack resistant render.
1. Optional Stucco BuildTM levelling mortar depending
on substrate conditions
2. Standard Mesh – glass fibre reinforcing mesh
3. NCB (tintable) – non-cementitious base coat
4. Dryvit PMR Finish - from standard or speciality
finish ranges
SUBSTRATE TYPES
Substrate
50
Dryvit ACR®
150
200
300
Cement Board
MD Finish SystemTM
Painted
Concrete/Render
Brick or Block
Sheathing
Board (soffits only)
Cement Board
on sheathed
frame
For more detailed information on acceptable substrates and application tolerances please contact Dryvit.
APPLICATION
DRYVIT ACR 200:
Flexible crack resistant render.
3. GenesisTM /DM – polymer modified cementitious
base coat
Dryvit UK Ltd.
STANDARD DETAILS
4. Dryvit PMR Finish and Color PrimeTM primer - from
standard or speciality finish ranges
Standard details are available for both Dryvit ACR systems and the
Cement Board MD Finish System and can be downloaded from
www.dryvit.co.uk.
DRYVIT ACR 150:
Reinforced re-profiling render with crack
resistance. NBS Specification Clause - M20
1. Stucco BuildTM levelling mortar depending on
substrate conditions
2. Ultramesh® – glass fibre reinforcing mesh
embeded in Stucco build
DRYVIT ACR 50:
Cost effective acrylic render system.
FINISHES
CEMENT BOARD MD FINISH SYSTEMTM:
CUSTOM BRICKTM
LYMESTONETM
TERRANEO ®
Anti-crack render system over cement board
with drainage cavity. NBS Specification
Clause - M20.
1. Dryvit Backstop® NT or other approved breather
membrane
2. Timber batons – used to form drainage cavity and as
support for cement board
3. Cement Board
5. GenesisTM/DM/DMS – polymer modified
cementitious base coat
6. Dryvit PMR Finish and Color PrimeTM primer- from
WARRANTY
The systems outlined above have varying degrees of crack resistance and therefore
depending of specific projects conditions movement joints may be required. Please consult
Dryvit UK regarding appropriate system selection and specification.
DRYVIT UK LTD
Tel: 01462 819555 Fax: 01462 819556
DRYVIT PREFABRICATED FEATURES
STANDARD AND CUSTOM PREFABRICATED EIFS MOULDINGS
Dryvit’s Prefabricated Features are an innovative range
of mouldings that enable architects and specifiers to
transform the exterior façades of new build and
renovation projects.
The mouldings use the same composite construction as
the company’s successful Outsulation® exterior insulation
and finishing system (EIFS).
Traditional features include cornices, pilasters and corbels
with a more contemporary range available to suit your
desired look. We can also produce special designs and
shapes customised for specific needs.
Dryvit’s Prefabricated Features take their place as a viable
and cost-effective method of reproducing either the
look of traditional buildings on the most modern of
developments or transforming a façade into a
contemporary work of art.
Crowborough
Whitefriars
Chester
BENEFITS
•
Chester
Design freedom. The prefabricated features can be installed over a variety of substrates. Expanded polystyrene
(EPS) core is lightweight and can be cut into virtually any shape or style with endless possibilities. Range of standard
features with custom profile service available.
The advantage of Dryvit Prefabricated Features stems from the unique production process whereby the
• Quality.
mouldings are designed, pre-cut and pre-coated in a controlled factory environment, guaranteeing quality.
track. Prefabricating the mouldings dramatically reduces the time associated with the labour intensive manufacture
• Fast
of site formed EIFS features. The lightweight nature of the profiles and simple fixing methods ensure that the features
are quick to install compared to alternatives such as stone, GRP, powder coated aluminium or site formed EIFS shapes.
Weatherability. Dryvit finishes are formulated to provide the utmost in weather protection providing a resilient barrier
•
The combination of components provide unsurpassed long-term durability meeting design requirements
• Durability.
for use in virtually any location.
Dryvit Prefabricated features can transform a buildings façade adding to it’s appeal and value. Also the
• Aesthetics.
Dryvit finishes used to coat the features are available in a wide array of textures in both standard and custom colours.
Our speciality finishes enable designers to replicate a variety of real stone finishes from limestone to granite at a
fraction of the cost.
effective. On account of the savings in installation and versatility of manufacture, no matter how simple or
• Cost
complex moulding shape, Dryvit Prefabricated Features are more cost effective than alternatives such as stone, GRP or
powder coated aluminium.
DUK 906
DRYVIT PREFABRICATED FEATURES:
SUBSTRATE TYPES
A shaped expanded polystyrene (EPS) core coated with a
non-cementitious acrylic base coat and coated with one of
Dryvit’s standard or speciality finishes.
NBS Specification Clause – Please consult Dryvit UK Ltd.
effective substrates and common substrates include exterior
insulation and finishing systems (EIFS), Insulated Concrete Forms
(ICF), concrete, blockwork, brick and render.
1. Adhered to substrate with
adhesive and dowels where
required
2. Expanded polystyrene core
APPLICATION
Application of the features are carried out by Specialist Installers
3. Base coat and reinforcement
4. Dryvit PMR finish – from
ranges
Dryvit UK Ltd.
STANDARD & CUSTOM FEATURE PROFILES:
Standard profile brochures are available from Dryvit UK Ltd. on
01462 819555 or can be downloaded from www.dryvit.co.uk.
Where custom profiles are required please contact Dryvit UK Ltd.
FINISHES
INSTALLATION:
Features being cut to size
on site
Installation of cornice
CUSTOM BRICKTM
LYMESTONETM
TERRANEO ®
WARRANTY
Taping of joints
Installation of feature
DRYVIT UK LTD
Tel: 01462 819555 Fax: 01462 819556
DRYVIT STANDARD & SPECIALITY FINISHES
DRYVIT SYSTEMS WITH A SPECIALITY FINISH…..DEMONSTRABLY SUPERIOR
Dryvit’s range of ‘specialist’ finishes enable designers to
achieve the look of granite, limestone, reconstituted
stone, brickwork, wood or stone feature work providing a
durable and lightweight equivalent to their natural
alternative at a fraction of the cost. TerraNeo,
Ameristone, Stone Mist, Custom Brick, Brick Effect, Wood
Effect finishes and our Prefabricated Feature profiles
complement the standard texture range and are available
in a wide choice of colours with the option to match stone
or brick where required.
The specialist finishes further extend the versatility of
Dryvit’s external insulation and anti-crack render systems
and provide architects, specifiers and building owners
with a highly adaptable method of achieving striking
aesthetic results.
When the speciality finishes are combined with our range
of external wall insulation systems they provide a
thermally efficient cladding solution that is difficult to match
in terms of performance when using more traditional
cladding options.
Whether the project is new build or renovation Dryvit’s
‘specialist’ finishes offer high-performance characteristics
that ensure a long-lasting radiant finish certain to enhance a
building’s stature.
www.dryvit.co.uk Tel: 01462 819555
Printed in the UK R1: 07/13 ©Dryvit UK Ltd. 2013
DUK 920
STANDARD FINISHES
Today’s building exterior demands high performance
cladding. Dryvit’s external wall insulation (EWI) and anticrack render systems satisfy these demands and often
exceed the toughest regulatory requirements. The standard
range of finishes and textures that are used with our range
of systems offer specifiers and clients the versatility to meet
their aesthetic aspirations.
The standard texture PMRB range offers 100% acrylics
incorporating dirt pickup resistant (DPR) and proven mildew
resistant (PMR) properties with aggregates ranging from
1-3mm.
We also offer high performance Dryvit HDPTM and FD PMR
finishes. HDP textured finishes incorporate silicone-based
technology that promote hydrophobic properties, which
repel water resulting in less dirt pick up and a cleaner wall
appearance.
FD PMR finishes are premixed 100% acrylic finishes
containing DPR and PMR technology as well as a film
forming accelerator for improved resistance to wash off.
Drytex and SLK are mineral and silicate based finishes
generally offered on our mineral wool based external wall
insulation system. Also our mineral based Dash Receiver
and Dash Aggregate finish can satisfy parochial planning
requirements offering a wide range of dash aggregate
Sandpebble
Sandpebble FineTM
Sandblast TM
Quarzputz TM
Freestyle TM
Dash Aggrigate
colours on all our insulated and anti-crack render systems.
The high performance pigments incorporated in our finishes
enable a wide range of colour options and if we don’t have
the colour you want in our standard range we have a colour
matching service that will be sure to satisfy your needs.
Even the most demanding deep and bright colours can be
achieved.
DUK 921
CUSTOM BRICKTM & BRICK EFFECT
Manufacturing and transporting clay bricks is energy
intensive. On site installation commonly involves several
trades with the substrate protection and insulation often
supplied by others without a single source responsibility or
warranty for the performance of the wall. A Dryvit system
incorporating either a Custom Brick or Brick Effect finish
provides an environmentally superior, simpler, cost effective
alternative, from a single source.
Custom Brick utilises a template installed over a coloured
base coat prior to the finish application. On removal of the
brick template the custom brick is revealed. Custom Brick
comes in a variety of options and we can also match an
existing building brick or stone pattern and size. Combine
this design flexibility with an infinite selection of colours,
textures and shading techniques, and your building exterior
can look exactly the way you want!
Dryvit Brick Effect is a ready to use polymer modified cementitious render, used to create a brick effect finish. The system
is applied in two different coats, the mortar coat and the face coat. The top coat is cut through to expose the mortar base
coat, creating the full brick and mortar joint effect. The joints produced are slightly deeper than our Custom Brick finish and
it is extremely versatile as joints are cut on site to suit. The finishes are available in a range of typical brick colours to satisfy
parochial requirements.
Custom Brick
Brick Effect
Standard Templates (custom templates available)
Custom Brick finish
and it is extremely
versatile as joints are
cut on site to suit.
Used Wall Brick
New Brick
Soilder Course
DUK 922
TERRANEOTM & AMERISTONETM
‘Solid’…’Stately’…’Monumental’ all describe buildings made
of granite. Granite, like brick, is heavy and energy intensive
to find, produce, and transport. To accommodate its weight,
a building also requires more concrete and steel structural
support – adding to the cost and environmental footprint of
TerraNeoTM Amazon 204
the project.
AmeristoneTM Pearl 011
Incorporating a blend of quartz, minerals and mica, Dryvit’s
TerraNeo and Ameristone finishes are an environmentally
sustainable, 21st Century alternative – allowing you to
create the appearance you want without the cost, duration
and environmental impact associated with heavier materials.
TerraNeoTM
Gibraltar
200
Zanzibar
201
Serengeti
202
Sonora
203
Andes
205
Vesuvius
206
Glacier
207
Teton
208
Everest
209
White Ash
014
River Rock
015
Champagne
Gray
016
Sedona Red
017
Emerald Isle
018
Victorian
Rose
019
Midnight
Storm
020
AmeristoneTM
Stony Creek
012
Woodbury
Pink
013
DUK 923
STONE MIST
TM
Stone or reconstituted stone, like brick, is heavy and energy
intensive to find, produce, and transport, Stone Mist is a
more refined finish than its sister products, TerraNeo and
Ameristone. Whether you are striving to create a solid,
upscale appearance for an exterior or unique and durable
finish for an interior, Stone Mist will enhance a building’s
value by adding both style and substance to it.
Stone Mist is coloured quartz aggregate finish premixed in
acrylic binder, which provides a natural stone appearance
at a fraction of the cost of its natural and recon alternatives.
Like all Dryvit finishes, Stone Mist is highly versatile. Use
it as a finish for any Dryvit external wall insulation systems
or directly applied to properly prepared substrates such as
masonry, render or interior drywall.
Stone Mist is available in a range of standard colours but
can also be matched to stone or recon stone.
Castle Gray
101 SM
Moon Glow
103 SM
Cinnamon Toast
105 SM
Stone Mountain
107 SM
Golden Sunrise
109 SM
Wedgwood Gray
102 SM
Desert
104 SM
Winter Moon
106 SM
Morning Fog
108 SM
Canyon Valley
110 SM
DUK 924
LYMESTONETM & WEATHERLASTIC ADOBETM
Similar to brick, granite and stone, limestone is another
heavy material from a bygone era that is energy intensive
to harvest, shape, transport and install. Lymestone and
Weatherlastic Adobe finishes by Dryvit, however, are not.
Lymestone and Weatherlastic Adobe finishes are comprised
of natural minerals, blended with 100% acrylic polymers and
long lasting pigments, and our readily available in an infinite
colour selection.
On larger wall surfaces, EPS profiles and aesthetic reveals
are commonly used to yield realistic limestone effect.
Lymestone and Weatherlastic Adobe finishes are often
used to compliment other Dryvit finishes such as, TerraNeo,
Ameristone, Stone Mist, Custom Brick, Brick Effect and
Tuscsan Glaze (old world plaster appearance).
Lymestone or Adobe
TerraNeoTM & Lymestone
or Adobe
Lymestone or Adobe
treated with Tuscan
Glaze™
Lymestone or Adobe &
Custom Brick™ or Brick
Effect
On larger wall surfaces, EPS
shapes and aesthetic reveals
are commonly used to yield a
realistic ashlar effect.
The smooth Lymestone or
Adobe finishes complement
Dryvit TerraNeo - The
Revolutionary finish that uses
minerals and mica to yield a
highly realistic granite and
smooth stone effect.
Lymestone or Adobe are the
perfect finishes on which to apply
Dryvit Tuscan Glaze - resulting in
an old world plaster appearance.
The very traditional and popular
limestone and brick combination
is eminently affordable using
Dryvit speciality finishes.
DUK 925
REFLECTITTM
A shiny reflective look can add sophistication to any façade.
Metal is a great complement to other finishes, and until now
there have been limited and expensive options for achieving
261 Chili Pepper
260 Caribbean
this appearance. Dryvit’s Reflectit coating, used as the finish
for any of our external wall insulation systems results in a
lightweight, energy efficient and cost effective, engineered
cladding.
An array of textures, including smooth is available and there
is a wide range of colours to select from.
254 Sierra Rose
253 Cleopatra
256 Mediterranean
255 Tin Man
258 Barney
257 Champagne
259 Maize
250 Teal Magnolia
252 Hammered
Copper
251 Starry Night
DUK 925
DRYTEX WOOD EFFECT
Drytex Wood Effect is a white ready to use blend of polymer
modified cementitious powders, which only require the
addition of water to produce a high quality finish. After
application a wood grain texture is created by impressing a
flexible wood pattern moulding into the render before it
has set.
Once the desired grain pattern has been achieved and
the render allowed to cure a Dryvit Wood Stain or solid
colour coating, either Demandit or Silstar, can be applied to
facilitate the desired finish.
As with brick and other cladding options timber cladding is
supplied as a separate component to insulation and other
ancillary items and in many cases they are installed by
different trades. Using Drytex Wood Effect as a finish option
over one of our external wall insulation systems can prove
to be a cost effective alternative, avoiding complicated
system transition details, with a single source responsibility
for product warranty.
The versatility of the Drytex Wood Effect finish is endless with a wide selection of wood stains or solid colours available.
Dryvit Wood Stains (Translucent)
Dryvit Solid Colour Coatings
Mahogany
Oak
Pine
Choose from a wide range of wood stain colours.
Select from the full range Dryvit colours using Demandit
or Silstar coatings.
DUK 927
For technical assistance on any of our external wall or
anti-crack render systems, or to request colour charts or
samples for any of our standard or speciality finish products
please contact us at:-
Dryvit UK Limited
Unit 4 Wren Park
Hitchin Road
Shefford
Beds
SG17 5JD
Tel: 01462 819 555
Email: [email protected]
www.dryvit.co.uk

Cost effective. - Dryvit | External Wall Insulation

Transcription

Similar documents

StratoTone

Cleaning and Restoration of EIFS

Full Brochure

2580 sq ft rambler Dryvit and stone detail Seamless steel siding 12 ft

Full Brochure

Blake`s Lotaburger #92

HomeSUITEHome - International Builders` Show

KASALA FURNITURE

Armourcoat

ExamView Player

Dryvit catalogue - Tri