frm catalogue 2014-us

light-weight racing parts since 1990
hand made in Italy
2014 USA
ANAKIN FULL monocoque | frame
29”
• 100% Made in Italy
• Monocoque mainframe and stays, manufactured under FRM licence
• Proprietary design of frame and moulds
• High Modulus Carbon Fibre, with optimised unidirectional layering
• UniFlex suspension system. No pivot between upper and lower stays. Higher rigidity and lighter weight
• Rear wheel travel: 100mm
• Chainstays: short at 438mm.
• BB height: 312mm
• Rear shock: DT Swiss X313 Carbon (165mm)
• Post-Mount brake support
• Dropouts: replaceable E-Thru 12x142mm with 12mm bolt axle
• S3 Direct-Mount front derailleur adaptor
• Internal routing of rear brake and both derailleurs
• Head Tube: 1,5” taper
• Headset: FRM D-Set 1,5” Taper included
• Bottom Bracket: Press-Fit 89,5mm (41x89,5mm)
• Hard anodised suspension axles in light alloy
• Full-ball type bearings (Enduro Max) with O-Ring shields
• Seatpost Dia.: 31,6mm
• Seatpost collar: FRM SC35 Ti. included
• Sizes: Small/ Medium - Large/X-Large
• Finish: perfect out of the mould finish does not require paint
• Rider weight limit: 95kg
• Weight: 1.850g. (Medium) with rear shock + E-Thru axle 38g
OPTION: Small/Medium.
Large/XLarge.
Code FRASLX0
Code FRASLX1
Direct-Mount S3 adaptor
29”
anakin
full SMALL/MEDIUM
LARGE/X-LARGE
P1
450
490
P2
342
342
A
585
620
2 catalogue 2014 | www.frmbikeusa.com
B
438
438
C
1.090
1.124
D
312
312
E
95
115
F
507
507
a
71,0°
71,0°
b
73,6°
73,6°
Cyclist height
from 165 to 179cm
from 180 to 189cm
ANAKIN SLK monocoque| frame
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
29”
100% Made in Italy
Monocoque mainframe and stays, manufactured under FRM licence. Proprietary design of frame and moulds
High Modulus Carbon Fibre, with optimised unidirectional layering
Post-Mount brake support
E-Thru (12x142mm) replaceable dropouts
Embossed FRM logo on the top tube
Internal routing of front and rear derailleurs
Head Tube: 1,5” - 1 1/8“ Integrated
Headset: FRM D-Set 1,5” Taper included
Bottom Bracket: Press-Fit 89,5mm (41x89,5mm)
Seatpost Collar: FRM SC32 Ti. included
Seatpost diameter: 27,2mm
Shelter BC shields included
Sizes: Small/Medium - Large/XLarge
Finish: perfect out of the mould finish does not require paint
Rider weight limit: 95kg
Weight: 1050g. (Small/Medium) + E-Thru axle 38g
OPTION: Small/Medium.
Large/XLarge.
anakin
29”
SMALL/MEDIUM
LARGE/X-LARGE
Code FRASSM0
Code FRASSM1
P1
470
510
P2
395
430
A
585
617
B
430
430
C
1.072
1.102
D
295
295
E
95
115
F
492
492
a
72°
72°
b
74,5°
74,5°
Cyclist height
from 165 to 179cm
from 180 to 189cm
www.frmbikeusa.com
| catalogue 2014
3
VENUS XC CARBON TUBULAR
•
•
•
•
•
•
•
•
•
•
•
•
29” 650b
Hubs and rims are made in Italy
Among the lightest wheels available worldwide for 29” or 650b” tubular tyres
The EVO carbon Tubular 29” and 650b is compatible with glued tubular tyres
Asymmetric profile for lower difference in spoke tension beteween right and left sides
The tension difference between right and left spokes is less than 10%. This makes a much more stable wheel
Spokes: Sapim CX Ray black. One spoke length for wheelset: 278mm for 29”. 260mm for 650b wheels
Hubs: FRM Venus Super Race. Four “Big Pawls”, drilled flanges and toothed ring in titanium
Holes: 24 front, 24 rear
Supplied with Bearing Tool Kit, 10s and 11s XX1 freewheels, four outer caps (QR15, QR9, X12, QR10),
two spare spokes
Crash Replacement Programme: rims returned for damages not in warranty are replaced at 50% of the
actual price list
Rider weight limit: 90kg
Weight: 29” 1.260g. set 650b 1.220g set
OPTION: Bolt or lever thru-axles (see page 7)
29”
Code WHVC001
29” with front Lefty
Code WHVCL01
650b
Code WHVC002
650b with front Lefty
Code WHVCL02
Double wheelbag
Code WHDWB01
Accessories supplied with wheelsets
OPTIONS
4 catalogue 2014 | www.frmbikeusa.com
thru-axle quick release
Venus lefty super race
wheelbag
VENUS XC MARATHON TUBULAR
•
•
•
•
•
•
•
•
•
•
•
29” 650b
Hubs and rims are made in Italy
XMD309 Tubular rims in 6082 light alloy are compatible with glued tubular tyres
Steel Eyelets. Anodised and laser etched
Asymmetric profile for lower difference in spoke tension beteween right and left sides
The tension difference between right and left spokes is less than 10%. This makes a much more stable wheel
Spokes: Sapim Laser 2,0-1,5-2,0mm. One spoke length for wheelset: 280mm for 29”. 262mm for 650b wheels
Hubs: FRM Venus Super Race. Four “Big Pawls”, drilled flanges and toothed ring in titanium
Holes: 32-32
Supplied with Bearing Tool Kit, two freewheels (10s & 11s XX1), four outer caps (QR15, QR9, X12, QR10),
two spare spokes
Rider weight limit: 90kg
Weight: 29” 1.395g. set 650b 1.325g set
OPTION: Bolt or lever thru-axles (see page 7)
29”
Code WHVMT01
29” with front Lefty
Code WHVMTL1
650b
Code WHVMT02
650b with front Lefty
Code WHVMTL2
Double wheelbag
Code WHDWB01
Accessories supplied with wheelsets
OPTIONS
thru-axle quick release
Venus lefty super race
www.frmbikeusa.com
wheelbag
| catalogue 2014
5
VENUS Super Race - MTB Disc
•
•
•
•
•
•
•
•
•
•
•
Made in Italy
Designed for X-Country Racing, they feature large diameter flanges and 17mm axles for optimal torsional rigidity necessary for 29ers
Flange spacing has been designed for minimal difference in spoke tension between right and left sided spokes
Freewheel with four “Big Pawls” to evenly distribute the loads on a large surface
Supplied with Bearing Tool Kit, two freewheels (10s & 11s XX1), four outer caps (QR15, QR9, X12, QR10)
Three Rubber Lip Seals make the freewheel as well as outer bearings completely waterproof
The toothed ring of the freewheel is in Titanium (8g. lighter than steel ring)
The 17mm axles in Scandium light alloy are stiff and light. Hard anodised for longer lasting lifespan
Holes: 32 front and rear
Finish: black anodised and laser etched
Weight pair: 360g. (117+243)
109g. front Venus Lefty Super Race (new model with self-extractor)
OPTION: Bolt or lever thru-axles (see page 7)
Hubset 32h
WHVHU1
Hubset 32h with front Lefty WHVHL2
1
Freewheel driver with four “Big Pawls”
2
17mm axle in light alloy. Hard anodised
3
Toothed ring in Titanium
1
3
2
Venus Lefty Super Race with tool for self-extracting flange
6 catalogue 2014 | www.frmbikeusa.com
THRU-AXLES
•
•
•
•
•
•
•
•
•
Made in Italy
Front QR15 axles are compatible with Rock Shox and Fox forks
Rear E-Thru axle is compatible with 12x142 E-Thru (Shimano standard M12x1,5mm) frames. Supplied with splined nut
Rear axle compatible with 12x142 Sram Maxle standard (M12x1,75mm)
CNC machined form 7075 light alloy
Hard anodised
Bolt system for extreme weight reduction and to make the wheel change faster than with quick releases
Front axles feature an Allen key holder so it is always on hand without loosing time to search for it
Weight: front QR15 36gr (weight saving with respect to Rock Shox or Fox: 37g)
rear E-Thru 38gr (weight saving with respect to Shimano E-Thru quick release 52gr)
rear Maxle compatible 38gr (weight saving with respect to Maxle quick release 35gr)
OPTION: Front QR15 Rock Shox compatible
Front QR15 Fox compatible
Rear 12x142mm Shimano E-Thru compatible
Rear 12x142mm Sram Maxle compatible
Code WHTA001
Code WHTA002
Code WHTA003
Code WHTA004
A hex key can be stored inside the hollow axle
TASK TEAM
•
•
•
•
•
•
•
Thru-axle type quick releases
CNC machined from light alloy
9mm front and 10mm rear axles in light alloy solid axles
Compatible with QR9 front hubs and QR10 rear hubs
Black anodised and laser etched
Weight: 78g. pair (33+45g.)
Code WHTT01N
www.frmbikeusa.com
| catalogue 2014
7
EVO CARBON Tubular
•
•
•
•
•
•
•
•
•
•
•
•
•
•
29” 650b
Made in Italy
For glued Tubular tires
Perfectly compatible with road bikes with disc brakes
Manufactured under FRM license. Proprietary design and mould
Hyperlight, yet torsionally very stiff
T800 Caron Fibre, with optimised unidirectional layering for excellent suppleness and extreme torsion stiffness
Asymmetric profile for better and even spoke tension
If coupled to FRM Venus hubs the tension difference between right and left sided spokes is less than 10%
Holes: 32
Dimensions: Width 26mm. Height 29mm
ERD 29” 580mm
650b: 544mm
Suggested spoke tension: 130kg
Rider Weight Limit: 90kg
Weight: 29” 300g. 650b: 280g.
OPTION: 29” Code EVOCT93
650b Code EVOCT71
XMD309 Tubular
FRM logo embossed on carbon fibre surface
29” 650b
• Made in Italy
• For X-Country Racing with Tubular tyres. Tested in the World Cup
• Anodised and laser etched
• Eyelets: single in stainless steel
• Asymmetric profile for better and even spoke tension
• Holes: 32
• Dimensions: Width 24,5mm. Height 18mm. Outer dia. 29” 630mm 650b 595mm
ERD 29”: 604mm ERD 650b: 568mm
• Suggested spoke tension: 130kg
• Rider Weight Limit: 85kg
• Weight: 29” 355g. 650b 330g.
OPTION: 29” Code EVOAT93
650b Code EVOAT73
8 catalogue 2014 | www.frmbikeusa.com
CU3-M11 Single Syncro-Ring
29” 27,5”
•
•
•
•
•
•
Compatible with 1x10 or 1x11 (XX1 o X01) drivetrains
Lever CNC machined from Scandium light alloy. Black Hard Anodised levers. Extremely long lasting finish
25mm axle, CNC machined from Scandium alloy. Hard anodised
Double-seal bearings with dust seals
CNC machined spider compatible with Sram XX1 single rings
FRM Syncro-Rings with narrow/wide tooth profile (à la XX1) to create a more secure
engagement and reduce the likelihood of dropping a chain (see page 11)
• Cranksets are supplied with 32T Syncro-Ring. 30T or 34T must be purchased separately
• Chainguides are not necessary
• Torx type Chainring Fixing Bolts in light alloy (XX1 compatible M8,4x0,75mm)
• Q-Factor: 163mm Chainline: 50,5mm
• Weight without Bottom Bracket (172,5mm / 32d): 570g.
• Weight of bottom brackets:
BSA: 87g.
Press-Fit: 65g.
BB30 / Press-Fit30: 70g.
OPTION: Arm length: Bottom Bracket: 170mm
172,5mm
175 mm
BSA 68 / 73
BB30 73 / 84,5
Press-Fit 89,5 / 92
Press-Fit 30 73
Code C113201
Code C113202
Code C!!3203
Code CSBB001
Code CSBB002
Code CSBB003
Code CSBB004
1
Gold plated Titanium hardware (2pcs)
2
Replaceable spider Sram XD compatible
with XX1 compatible fixing bolts (4pcs)
2
1
CHAINRING BOLTS - XX1 Compatible
•
•
•
•
•
•
•
Made in Italy
CNC machined from 7010 light alloy. Compatible Torx 30
Male only
Dimensions: M8,4 x 0,75mm Thread length: 5,8mm
Black anodised
FRM laser etched
Code CodeCRCHFB2
www.frmbikeusa.com
| catalogue 2014
9
CU3-M11 Single Osymetric
•
•
•
•
•
•
•
•
•
•
29” 27,5”
Compatible with 1x10 or 1x11 drivetrains
Lever CNC machined from Scandium light alloy. Black Hard Anodised levers. Extremely long lasting finish
25mm axle, CNC machined from Scandium alloy. Hard anodised
Double-seal bearings with dust seals
34t oval Osymetric ring
Q-Factor: 163mm Chainline: 48mm
The FRM KCU chain-guide is necessary. Most chainguides are not compatible with very ovalised rings
Rider Weight Limit: 90kg
Weight without Bottom Bracket (172,5mm): 600g.
Weight of bottom brackets: BSA: 87g.
Press-Fit: 65g.
BB30 / Press-Fit30: 70g.
OPTION: Arm length: Bottom Bracket: 170mm
172,5mm
175 mm
BSA 68 / 73
BB30 73 / 84,5
Press-Fit 89,5 / 92
Press-Fit 30 73
Code CSM1104
Code CSM1105
Code CSM1106
Code CSBB001
Code CSBB002
Code CSBB003
Code CSBB004
1
Gold plated Titanium hardware (2pcs)
2
Replaceable spider for single chainring
with single fixing bolts (4pcs)
2
1
CHAINRING BOLTS - Standard
•
•
•
•
•
•
Made in Italy
CNC machined from 7010 light alloy. Compatible Torx 30
Set of male and female
Dimensions: M8 x 0,75mm Thread length: 7,8mm
FRM laser etched
CodeCRCHFB1
10 catalogue 2014 | www.frmbikeusa.com
NS TOOL 25
•
•
Tool to disassemble the NS chainrings or the four-arm spider
Price USD 26 Code CSNS25
SYNCRO-RING XX1 SINGLE
•
•
•
•
•
•
•
29” 27,5”
Made in Italy
Narrow and wide tooth profile (à la XX1) to create a more secure engagement and reduce the likelihood of dropping a chain
CNC machined from 7075 aluminium. Polished, anodised Black and laser etched
Compatible with original Sram XX1 or FRM CU3-M Single XX1 cranksets with 10 or 11 speed cogsets
No need for a chainguide
Conforms to US patent 4,174,642 Nov 20 1979
Weight: 30t 39g. 32t 43g. 34t 50g. (8 / 10g. lighter than original XX1 rings)
OPTION: 30t Code CRS0001
32t Code CRS0002
34t Code CRS0003
SYNCRO-RING 104 SINGLE
•
•
•
•
•
•
•
29” 27,5”
Made in Italy
Narrow and wide tooth profile (à la XX1) to create a more secure engagement and reduce the likelihood of dropping a chain
CNC machined from 7075 aluminium. Polished, anodised Black and laser etched
Compatible with 104mm BCD 4-arm cranksets and 10 or 11 speed cogsets
Can convert your current triples or doubles into singles whilst eliminating the need for a chainguide
Conforms to US patent 4,174,642 Nov 20 1979
Weight: 32t 39g. 34t 46g.
Syncro-Ring teeth profile
OPTION: 32t Code CRS1041
34t Code CRS1042
KCU Carbon Chain-guide
•
•
•
•
•
•
•
Made in Italy
For X-country and Enduro bikes with single rings
Inner and outer cages made in moulded carbon fibre. Embossed FRM logo
Collar (34,9mm) and Direct-Mount adapters in 7075 light alloy
Titanium hardware (8 pcs)
Designed to also be compatible with extreme oval shaped rings
Weight: High Collar 35g. Low Collar 33g. Direct-Mount S3 30g.
OPTION:
High collar (seat tube dia. 34,9mm)
Low collar (seta tube dia. 34,9mm)
Direct-Mount S3 (Chainring compatibility 26-38T)
High Direct-Mount (Chainring compatibility 26-38t)
Code CG00001
Code CG00002
Code CG00003
Code CG00004
Low Collar
High Direct Mount
High Collar
Direct Mount S3
www.frmbikeusa.com
| catalogue 2014
11
WEB-STEM 6B Ti.
•
•
•
•
•
•
•
29” 27,5” 26”
Made in Italy
CNC machined from a solid billet of Scandium light alloy. Black anodised and laser etched
Titanium hardware (6pcs)
Interchangeable angle +/-7° with flip-flop logo
Stack height (headset collar): 36,5mm
Rider Weight Limit: 85kg
Weight: 100g. 75mm
105g. 90mm
109g. 100mm
114g. 110mm
OPTION: length: 75mm
90mm 100mm
110mm
Distance between contact surface with headset and handlebar center
• 75mm:
Negative +11mm Positive +26
• 90mm:
Negative +9mm Positive +28
• 100mm:
Negative +8mm Positive +29
• 110mm:
Negative +7mm Positive +30
Code HSWS01N
Code HSWS02N
Code HSWS03N
Code HSWS04N
1
1
Gold plated Titanium hardware (6pcs)
1
HS-M15 Ti.
•
•
•
•
•
•
•
•
•
•
Made in Italy
CNC machined from a solid billet of Scandium light alloy. Black anodised and laser etched
15° negative angle, compatible with flat handlebars only
Stiffer than stems designs with removable caps
Perfect for 29” bikes when the saddle/handlebar height difference is not enough for your riding style
The FRM 229 handlebar is the perfect match with this low rise stem
Titanium hardware (4pcs)
Stack height (headset collar): 37mm
Rider Weight Limit: 90kg
Weight: 102g. 80mm 106g. 90mm 111g. 100mm 114g. 110mm
OPTION: length: 70mm
80mm
90mm
100mm
110mm
Code HSHS01
Code HSHS02
Code HSHS03
Code HSHS04
Code HSHS05
Distance between contact surface with headset and handlebar center
• 70mm:
+6mm
• 80mm:
+4mm
• 90mm:
+2mm
• 100mm:
- 1mm
• 110mm:
- 3mm
12 catalogue 2014 | www.frmbikeusa.com
29”
WEB-BAR CARBON 229
•
•
•
•
•
•
•
•
•
100% High Module carbon fibre
Off-centre. The bar height from ground can be modified by 10mm by flipping the bar
Flat with ideal width and angle for X-Country 29” or 27,5” bikes
Width: 700mm
Rise: 0mm
Diameter 31,8 / 22,2mm
Bend: 7° Backwards
Weight: 150g.
Code HB00001
29” 27,5”
FLAT. ASYMMETRIC (Reversible). 700mm WIDE
SILICONE GRIPS Off-Centre
•
•
•
•
•
•
•
•
•
•
•
Made of memory-form silicone
Off-centre for lighter weight, smaller diameter, but unchanged padding comfort
Slip-proof wet or dry, reduces hand fatigue
Will not harden or fade with time
No glue or lock-ons are required.
Washable
Length 120mm. Cut to 90mm with Sram twist shifters and save 30g. over the original grips
Diameter: 33mm
Packaged into an FRM water bottle
Weight: 72g. pair (54g. when cut to 90mm for Sram rotors)
Code HBG0001
1
1
Asymmetric profile. Rotate with the
thicker side toward the hand palm
www.frmbikeusa.com
| catalogue 2014
13
ST-M10 Ti.
•
•
•
•
•
•
Made in Italy
CNC Machined from Scandium alloy, externally double butted to save further weight
Black anodised post. Laser etched
Gold-plated Titanium bolts
Rider Weight Limit: 85kg
Weight: ST-M10 Ti. 27,2 x 350: 155g.
30,9 x 350mm 173g.
31,6 x 350mm 175g.
OPTION: 27,2 x 350mm
30,9 x350mm
31,6 x 350mm
Code SP1001N
Code SP1002N
Code SP1003N
1
1
Gold plated Titanium hardware (2pcs)
2
External double diameter
SC35 Ti.
•
•
•
•
•
•
•
2
Reduced diameter: 160mm
Reduced diameter XL: 170mm
SC32 Ti.
Made in Italy
Asymmetric seat collars ideal for carbon fibre seatposts as they put less pressure on the frame slot
SC32 compatible with frames that have 31,8mm diameter seat tubes
SC35 compatible with frames that have 34,9mm diameter seat tubes
Black anodised and laser etched
Height: 14mm
Weight: 11g.
OPTION: SC35 SC32
1
Code SC3501N
Code SC3201N
1 Gold plated Titanium hardware
14 catalogue 2014 | www.frmbikeusa.com
Clamp area: 110mm
Clamp area XL: 150mm
Minimum insertion:
80mm
ASPEN Ti.
•
•
•
•
•
•
•
•
•
Carbon Fibre reinforced moulded shell
Titanium rails
Leather surface with Kevlar reinforced wings
Super Light foam filling
Dimensions: 270 x 130mm
Black and White with FRM logo
Rider weight limit: 85kg
Weight: 210g.
Code SA00001
EXPANDER-PLUG TEAM
•
•
•
•
•
•
•
Minimum dia: 22,8mm
Light and efficient system to register headset play
Ideal for Carbon Fibre steerer tubes
100% aluminium
Play-adjustment bolt in Gold-plated Titanium (Torx25)
Black anodised and laser etched
Weight: 17g.
Code HSEP001
H2O BOTTLE
DOUBLE WHEELBAG
•
•
•
•
•
•
•
•
•
•
Transparent water bottle: 500 cc
Large mouth
FRM logo
Code GD00002
Max dia: 26mm
29” 650b 26”
Wheel-bag for two Road or MTB 26”/ 650b / 29er wheels
Padded outer and inner walls
Inner pocket for quick releases
Owner’s name holder
FRM logo
Code HSEP01N
BOTTLE OPENER
•
•
•
•
Aluminium
Allows bottle tops to be reused as it does not cause them to bend
FRM logo
Code GD00001
www.frmbikeusa.com
| catalogue 2014
15
FRM Bike USA
217 N. Westmonte Dr. Suite 2015
Altamonte Spring FL 32714
USA
[email protected]
WARRANTY
At FRM USA we strive to provide our customers with perfect bikes and components… But even
the best of families have problems at times, that’s why we have the FRM warranty:
Warranty: FRM USA products are guaranteed against any defects for a period of 2 years from
the date of purchase by the first owner.
Obligations: In case of defects, FRM USA pledge to replace or repair, at their discretion, the part
recognised as defective. To be accepted, the complaint must be communicated to FRM USA
either directly or through the dealer from which the part was purchased.
If FRM USA, after checking the part, finds that the damage is due to one of the reasons
mentioned in the following paragraph, the warranty request will not be accepted and the
detective item is sent back to the plaintiff who supports the shipping fees.
Limitations: The guarantee does not cover damage resulting from transportation, warehousing,
accidents, negligence, impact or falls, non-compatible products, bad maintenance, modifications
or alterations to the product. The guarantee does not cover parts and components subject to
normal wear and tear such as ball-bearings, bushings seals, brake pads, disc rotors, etc.
If you do have a problem with an FRM USA part that you think might be covered by warranty then
write to us at [email protected] and we will let you know how to proceed. Whatever the case,
whether covered by warranty or not, we will do our best to help resolve your problem in as little
time possible.
Oh, almost forgot… Our warranty does not cover sporting results. FRM products improve your
performance but they won’t automatically turn you into a champion. So, if you didn’t win your last
race, don’t blame us, just train harder next time!
Graphic design: PIRULINO.com