D-CJ500/CJ501/CJ506CK - Vintage

Transcription

D-CJ500/CJ501/CJ506CK
SERVICE MANUAL
US Model
D-CJ500/CJ506CK
Ver 1.1 2002. 05
Canadian Model
AEP Model
UK Model
E Model
D-CJ501
Australian Model
D-CJ506CK
Photo: D-CJ500
Model Name Using Similar Mechanism
D-EQ550
CD Mechanism Type
CDM-3125ER
Optical Pick-up Name
DAX-25E
SPECIFICATIONS
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wavelength: λ = 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance
of 200 mm from the objective lens surface on
the optical pick-up block with 7 mm aperture.)
D-A conversion
AEP/E13/East European/French model:
220 - 230 V, 50/60 Hz
UK model: 230 - 240 V, 50 Hz
Australian model: 240V, 50 Hz
Argentine model: 220 V, 50 Hz
Battery life* (approx. hours)
(When you use the CD player on a flat and stable
surface.)
Playing time varies depending on how the CD
player is used.
Figures in brackets show the playing time of
MP3 files.
1-bit quartz time-axis control
Frequency response
20 - 20 000 Hz
307)
+1
–3 dB
(measured by JEITA CP-
Output (at 4.5 V input level)
CJ500, CJ506CK:
Headphones (stereo minijack)
Approx.5 mW + Approx. 5 mW at 24 Ω
CJ501:
Headphones (stereo minijack)
Approx.5 mW + Approx. 5 mW at 16 Ω
(Approx. 1.5 mW + Approx. 1.5 mW
at 16 Ω)*
*For the customers in France
Power requirements
For the area code of the model you
purchased, check the upper left side of the
bar code on the package.
When using
Two Sony alkaline
batteries LR6(SG)
(produced in Japan)
G-PROTECTION function
“1”
“2”
32
30
[24]
[24]
* Measured value by the standard of JEITA (Japan
Electronics and Information Technology
Industries Association).
Operating temperature
Supplied accessories
For the area code of the location in which you
purchased the CD player, check the upper left side
of the bar code on the package.
CJ500:
Headphones (1)
CJ501:
AC power adaptor (1)
Headphones/earphones (1)
CJ506CK:
AC power adaptor (1)
Headphones (1)
Car battery cord (1)
Car connecting pack (1)
Velcro tape (2)
Design and specifications are subject to change
without notice.
• Abbreviation
E13 : 220-230V AC area in E model.
E92 : Chilean and Peruvian model.
5°C - 35°C (41°F - 95°F)
Dimensions (w/h/d) (excluding
projecting parts and controls)
Approx. 161.0 × 26.3 × 130.3 mm
(6 3⁄8 × 1 1⁄16 × 5 1⁄4 in.)
Mass (excluding accessories)
Approx. 210 g (7.5 oz.)
• Two LR6 (size AA) batteries: 3 V DC
• AC power adaptor (DC IN 4.5 V jack):
US/Canadian/E92 model:
120 V, 60 Hz
9-873-669-02
Sony Corporation
2002E1600-1
© 2002.05
Personal Audio Company
Published by Sony Engineering Corporation
PORTABLE CD PLAYER
TABLE OF CONTENTS
1. SERVICING NOTE ·························································· 3
This appliance is classified as a CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT MARKING is located on
the rear exterior.
2. GENERAL ·········································································· 4
3. DISASSEMBLY ································································ 5
3-1.
3-2.
3-3.
3-4.
3-5.
Battery Case Lid, Cabinet (Upper) Assy ······················· 5
Upper Lid Assy ······························································ 6
MAIN Board, MD Assy (CDM-3125ER) ····················· 6
Turn Table Motor Assy (M901) ····································· 7
Motor Assy (Sled) (M902),
Optical Pick-up (DAX-25E) ·········································· 7
4. ELECTRICAL ADJUSTMENTS ································· 8
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
5. DIAGRAMS ········································································ 9
5-1.
5-2.
5-3.
5-4.
5-5.
5-6.
5-7.
5-8.
Block Diagram ···························································· 10
Printed Wiring Board – MAIN Board (Side A) – ······· 12
Printed Wiring Board – MAIN Board (Side B) – ······· 13
Schematic Diagram – MAIN Board (1/4) – ··············· 14
IC Pin Function Descriptions ······································ 19
6. EXPLODED VIEWS ······················································ 26
6-1. Cabinet (Front) Section ··············································· 26
6-2. Cabinet (Lower) Section ············································· 27
6-3. Optical Pick-up Section (CDM-3125ER) ···················· 28
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
On AC power adaptor
7. ELECTRICAL PARTS LIST ······································· 29
• Use only the AC power adaptor supplied or
recommended in “Accessories (supplied/
optional).” Do not use any other AC power
adaptor. It may cause a malfunction.
Polarity of the plug
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
2
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SECTION 1
SERVICING NOTE
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
BEFORE REPLACING THE OPTICAL PICK-UP BLOCK
Please be sure to check thoroughly the parameters as par the “Optical
Pick-Up Block Checking Procedures” (Part No.: 9-960-027-11)
issued separately before replacing the optical pick-up block.
Note and specifications required to check are given below.
• FOK output: IC601 yg pin
When checking FOK, remove the lead wire to disc motor.
• RF signal P-to-P value: 0.35 to 0.75 Vp-p
LASER DIODE CHECK
During normal operation of the equipment, emission of the laser
diode is prohibited unless the upper lid is closed while turning ON
the S801. (push switch type)
The following checking method for the laser diode is operable.
• Method:
Emission of the laser diode is visually checked.
1. Open the upper lid.
2. Push the S801 as shown in Fig. 1.
3. Check the object lens for confirming normal emission of the
laser diode. If not emitting, there is a trouble in the automatic
power control circuit or the optical pick-up. During normal
operation, the laser diode is turned ON about 2.5 seconds for
focus searching.
S801
Fig. 1 Method to push the S801
3
SECTION 2
GENERAL
This section is extracted
from instruction manual.
CD player (front)
1 i (headphones)
jack
8 . (AMS/search) button
2 OPEN button
9 N >* (play, AMS/
search) button
q; Strap holes
3 VOLUME control
4 FOLDER –/+ buttons
qa DC IN 4.5 V
(external power
input) jack
qs x (stop) button
5 MENU button
qd HOLD switch
6 DISPLAY button
7 Display
qf SOUND button
*The button has a tactile dot.
CD player (inside)
qg G-PRO (G-PROTECTION) switch
4
CD player (rear)
qh Battery compartment
SECTION 3
DISASSEMBLY
Note :
This set can be disassembled in the order shown below.
SET
BATTERY CASE LID,
CABINET (UPPER) ASSY
(Page 5)
MAIN BOARD, MD ASSY
(CDM-3125ER)
(Page 6)
MOTOR ASSY (SLED) (M902),
OPTICAL PICK-UP (DAX-25E)
(Page 7)
Note :
UPPER LID ASSY
(Page 6)
TURN TABLE MOTOR ASSY
(M901)
(Page 7)
Follow the disassembly procedure in the numerical order given.
3-1. Battery Case Lid, Cabinet (Upper) Assy
1 three screws (+B 2 × 10)
2 cabinet (upper) assy
9
0
7 four claws
5 two claws
boss
6 two claws
4 two screws (+B 2 × 10)
8 four claws
3 battery case lid
5
3-2. Upper Lid Assy
2 upper lid assy
1 two claws
cabinet (front) assy
3-3. MAIN Board, MD Assy (CDM-3125ER)
Note :
When installing, fit S803 to the knob (HOLD).
4 MD Assy
1 connector (CN501)
3 connector (CN502)
2 connector (CN503)
5 MAIN Board
terminal (–), battery (BT402)
terminal (+.–), battery (BT400)
cabinet (lower) sub assy
S803
knob (HOLD)
6
3-4. Turn Table Motor Assy (M901)
1 three screws (+B 1.7 × 5)
2 turn table motor assy (spindle) (M901)
chassis
3-5. Motor Assy (Sled) (M902), Optical Pick-up (DAX-25E)
1 screw (+B 1.7 × 5)
feed screw assy
3 gear B
motor assy (sled) (M902)
5 screw (+P 1.4 × 3.5)
2
bracket (Shaft)
6
4
7
optical pick-up
(DAX-25E)
chassis
7
SECTION 4
ELECTRICAL ADJUSTMENTS
CD section adjustments are done automatically in this set.
In case of operation check, confirm that focus bias.
Test Point:
– MAIN Board (Side B) –
FOCUS BIAS CHECK
1. Connect the oscilloscope between TP603 (RF) and GND on
main board.
2. Insert the disc (YEDS-18). (Part No. : 3-702-101-01)
3. Press the B > button.
4. Confirm that the oscilloscope waveform is as shown in the
figure below. (eye pattern)
A good eye pattern means that the diamond shape ( ◊ ) in the
center of the waveform can be clearly distinguished.
3
IC601
• RF signal reference waveform (eye pattern)
VOLT/DIV : 200 mV
TIME/DIV : 500 ns
804
RF level :
0.55 ± 0.2 Vp-p
When observing the eye pattern, set the oscilloscope for AC range
and raise vertical sensitivity.
8
SECTION 5
DIAGRAMS
• Waveforms
(CD play mode)
Note For Printed Wiring Boards And Schematic Diagrams
Note on Printed Wiring Board
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
: Pattern from the side which enables seeing.
•
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
(Side A)
Parts face side:
(Side B)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or
less are not indicated except for electrolytics and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise specified.
•
% : indicates tolerance.
• C : panel designation.
Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.
1 TP603 (RF)
600 mVp-p
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce por tant le numéro
spécifié.
200 mV/DIV, 400 ns/DIV
2 IC601 <z/n>>(LRCKO)
• A : B+ Line.
• Total current is measured with CD installed.
• Power voltage is dc 4.5 V and fed with regulated dc power supply
from DC IN jack (J401).
• Voltages and waveforms are dc with respect to ground in playback
mode.
no mark : CD PLAY
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
J : CD
c : CD-R/RW (MP3)
• Abbreviation
FR
: French model.
22.5 µs
2.5 Vp-p
500 mV/DIV, 5 µs/DIV
3 IC601 rk>(XTAO)
1.3 Vp-p
59 ns
500 mV/DIV, 40 ns/DIV
4 IC801 q; (XTALO)
3.2 Vp-p
125 ns
1 V/DIV, 40 ns/DIV
9
9
5-1. Block Diagram – MAIN-1 Section –
IC601
RF AMP,
DIGITAL SIGNAL PROCESSOR,
DIGITAL SERVO PROCESSOR,
D-RAM CONTROLLER
DETECTOR
A
B
B
RF
RF
E
E
F
F
92
91
88
84
VCC
AOUT1
WDCK
GFS
A
B
LPF
AOUT2
51
56
14
LIN
LOUT
R-CH
LRMU
XTAO
XTAI
MUTE
61
19
PWRSW
28
FI1
33
RI1
34
FO2
E
F
RFAC
SFDR
100
SRDR
99
MDP
XSOE
SENS
FFDR
FRDR
XLAT
CLOK
SCOR
SDTO
DRIVER
F–
26
T+
TRACKING
COIL
23
RO2
LEVEL
SHIFTER
FO3
CONTROLLER
FI2
35
RI2
36
96
95
DRIVER
T–
21
RO3
FI3
13
RI3
14
98
97
SIGNAL
PROCESSOR
BLOCK
MEMORY
CONTROLLER,
BUS BOOST
BLOCK
D0-D3
4, 3,
6, 5
116-113,
17-15,
13-11,
117
A0-A10
XRAS
XWE
XCAS
TFDR
TRDR
19-12,
15-19, A0-A10
21,8
1
5 XRAS
4 XWE
23 XCAS
2
9
IC701
MP3 DECODER
M
DRIVER
S–
C+
30
19
RO1
21
FO4
M
B
SDTO
C
SCK
20
23
22
3
24
6
69
3
65
5
42
55
40
16
17
46
87
86
GRSCOR_INT
XSOE_O
GFS_I
FOK_I
7
SCOR_INT
2
SENS
7
41
100 OPGSW
95 OPSTB
25 30 31
:CD-R/RW(MP3)
10
10
60 CKO
48
62 XI
PO7
18
47
1 5 6 19
39
28
Q701
IC803
BUFFER
51 82 89
53
92
96 45 47 1
98
49 44
IC801 (1/2)
SYSTEM CONTROL
:CD
13 BCKIA
1
XLAT
• Signal path
OPGSW
OPSTB
26
SCK
same as L-ch.
1
5
83 STB_RW_O
• R-ch is omitted due to
27
SDTO
17
RO4
2
X601
16.9MHz
IC804
BUFFER
DRIVER
C–
6
XAPCOFF_O
32
FO1
XTAI
111
110
14 LRCKIA
MP3DSP_I
S+
61
5
MP3_DSP_RST
SDA0(I2C)
SCL0(I2C)
STANDBY_O
APCREF
3
XRDE_O
PD AMP
XTAO
107
106
12 SDI0
XRST_O
PAPC
XRDE
SERVO
BLOCK
SFDR
SRDR
FFDR
FRDR
TFDR
TRDR
SYSM
XQOK
XWRE
60
RF21
108
AMUTE_O
XQOK_O
XWRE_O
PD
B+ +3V
BCK_O
FOK
PD
62
BCK_I
GFS
59
LD AMP
VINDET
SENS
64
RF2
INM2
LRCK_O
RFDC
E
F
B
A
XLAT
63
MDS
CLOK
LD
102
SDTO
LD
3
16
XSOE
PDL/RI4
Q404,405
LD
DRIVER
LRCK_I
SDO
STANDBY
3
PCMD_O
MDP
9
IC703
BUFFER
1
7
/RESET
103
109
XRST
104
4
WDCK
15
C176
SCOR
PWM/FI4
PCMD_I
7
SYNC
1
20
2, 3,
24, 25 D0-D3
A
IC403
COMPARATOR
17
IC602
D-RAM
MIDIO
/MICK
OPSTB
FOCUS
COIL
89
90
IC401 (1/2)
FOCUS/TRACKING COIL DRIVER,
SPINDLE/SLED MOTOR DRIVER
OPGSW
F+
M901
SPINDLE
MOTOR
BEEP
PW SW
VCC1 +2V
OPTICAL PICK-UP
BLOCK
DAX-25E
M902
SLED
MOTOR
BEEP
MT SW
J301
i
R-CH
MDS
RFDC
RFAC
R-CH
8
BEEP_O
A
IC301
HEADPHONE AMP
RV301
VOLUME
– MAIN-2 Section –
LCD801
LIQUID CRYSTAL
DISPLAY
D0 - D7 56-63
S804 - 807
FUNCTION
KEY
28 KEY1_AD
DD0 - DD7
A0 64
RD 77
WR1 78
LCD_RST_O 97
A0
RD
Q409
B+
SWITCH
WR1
LCD_RST_O
D410
L410
48
D407
STNG
INP1
3.0V
29 KEY2_AD
V5_OUT
3
45
2
IC402
DC/DC CONVERTER
VCPU3V
Q801,803
KEY
DETECT
54
V5
Q802
SWITCH
S808 - 811
FUNCTION
KEY
IC401 (2/2)
POWER CONTROL
IC701
VDD
49
DTC1D
VIN
SWITCHING
POWER
CIRCUIT 2
VLGO1
53
B+ +3V
IC401
FOCUS/TRACKING COIL DRIVER
SPINDLE/SLED MOTOR DRIVER,
IC301
HEADPHONE AMP
19 KEY_INT
Q410
B+
SWITCH
VCC1+2V
S801
(CD DOOR OPEN)
Q406
B+ SWITCH
VCPU2 (2.0V)
18 OPENSW_INT
42
VCPU +2V
CHGSW
CHARGE
CONTROL
VCPU2 (2.0V)
37
VCPU1 (2.5V)
RESET 15
B+
CHG ON/OFF
IC802
1 RESET 3
VCC2 _2.5V
Q407
B+ SWITCH
43
VCPU1 (2.5V)
S802
G-PRO
RS
CHARGE
SWITCH
44
VCC1(2.5V)
D403
B–
RF4
Q408
88 GPRO_I
2
38
VCC1
40
DC IN
1
L405
A
SYNC
5
DRY BATTERY
SIZE "AA"
(IEC DESIGNATION LR6)
2PCS,3V
SYNC
CLK
OR OSC
SAWTOOTH
GENERATOR
DCIN
VG
INTERFACE
SWITCHING
POWER
CIRCUIT 5
Q402
GATE
Q401
SWITCH
41
S803
HOLD
6
ON
B
C
90 HPLD_I
OFF
SDTO
8
SCK
7
9
WAKEUP
DATA
CLOCK
L4
VG
LATCH
D411
4
RSTB
AMP
STANDBY
REFERENCE
BIAS
58
XLIGHT-ON 52
Q804
LED
DRIVER
BANDGAP
REFERENCE
(VREF)
VREF
D802
11 XTALI
X801
8MHz
XPOWLT_O
IC801 (2/2)
SYSTEM CONTROL
48
WAKEUP_O
10 XTALO
54
BAT1MNT_AD 25
DCIN_INT 21
DCINMNT_AD 31
11
11
Q403
DC IN
DETECT
1
2
D408
D404
L401
J401
DC IN 4.5V
!
5-2. Printed Wiring Board – MAIN Board (Side A) –
M901
M902
IC403
IC402
• Semiconductor
Location
Ref. No.
OFF
12
12
ON
Location
D402
D403
D404
D406
D408
D409
D410
D411
G-9
G-8
G-9
G-9
I-4
H-5
G-7
G-7
IC402
IC403
G-7
H-4
Q401
Q402
Q403
Q406
Q408
Q410
Q803
G-8
H-8
G-9
I-4
I-4
G-7
F-7
5-3. Printed Wiring Board – MAIN Board (Side B) –
IC602
IC703
IC701
IC601
IC804
IC802
IC801
IC803
IC301
• Semiconductor
Location
Ref. No.
IC401
13
13
Location
D405
D407
D412
D801
D802
H-2
I-4
H-7
D-6
J-7
IC301
IC401
IC601
IC602
IC701
IC703
IC801
IC802
IC803
IC804
F-9
H-5
C-8
B-8
C-5
B-6
F-5
E-4
F-6
E-6
Q404
Q405
Q407
Q409
Q701
Q801
Q802
Q804
H-7
H-7
J-5
I-4
D-4
E-4
J-6
J-7
5-4. Schematic Diagram – MAIN Board (1/4) –
• See page 19 for IC Pin Function Descriptions.
• See page 9 for Waveforms.
14
14
• See page 18 for IC Block Diagrams.
15
15
• See page 18 for IC Block Diagrams.
16
16
• See page 9 for Wavefoms.
17
17
IC401 TB2125F
• IC Block Diagrams
13
ALC
ALC
ATT
SW
48 47
46
45 44
43
42
41
40
39
BEEP
LOUT
VG
L1L 50
VG
PGND1 51
VG
DCIN
DCIN
VIN
–
+
+
–
PW
C
DCIN
VCPU
+
–
BST
PW
B
PW
A
VCPU2
VCPU
VCC1
L1H 52
PWC
SW
36 35 34 33
32 FO1
VCPU
R-2
VG
ADDA
37
VREF
VLGO1 49
ADDB
38
VREF
VG
ALC
DET
VCPU
29 VD12
SAW TOOTH
SUB VREF
ALC
IN
ALC
DET
R-6
VREF
STNG 54
BATM1 55
OEB
VREF
CONTROLLER
DCIN
LEVEL
SHIFTER
H BRIDGE
DRIVER 2
DCIN
27 MGND2
26 RO2
D-1 to 4
VCPU2
BATM2 56
25 VD23B
CHGMNT 57
VCPU
CLK
VREF 58
STANDBY
REFERENCE
RF21 59
VCPU
SAW TOOTH
SAW GEN
23 FO3
S-3
H BRIDGE
DRIVER 3
VCPU
VCPU
VCPU2
22 MGND3
21 RO3
VCPU
CLK
OR OSC
APCREF 61
VREF
24 VD23A
S-2
VCPU
R-4
PAPC 60
VREF
VCPU
VCPU
VIN
20 VD34
1/2 VREF
VCPU
VCPU
BIAS
VINDET 62
RF2 63
VREF
19 FO4
H BRIDGE
DRIVER 4
BANDGAP
REFERENCE
(VREF)
VCPU
S-1
VCPU
VG
VCPU
R-5
CLK
INTERFACE
INM2 64
VCPU2
VCPU
18
18
18 MGND4
17 RO4
VCPU
D-5
VG
1
2
3
4
5
6
7
8
9
10
11 12 13 14 15 16
FI3
RI3
PWM/FI4
PDL/RI4
PGND MIX
OUT
28 FO2
VG
MDP
LOUT
12
SAW TOOTH
VREF
11
COMP OUT
ROUT
10
LATCH
VCC
9
CLOCK
DATA
8
WAKEUP
7
SYNC
6
RSTB
RF IN OCL
SW
5
GND
ADD
OUT
4
VG
BST
NF
3
30 RO1
VIN
L4
2
31 MGND1
CHGON/OFF
SUB VREF
VCPU
H BRIDGE
DRIVER 1
CONTROL
CHARGE
R-1
VIN 53
1
FI2
14
RI1
FI1
15
RI2
ROUT
16
CHGSW
MT
SW
17
RS
PW
SW
ATT
SW
INM4
18
LIN
RF4
19
RIN
DCIN
BIAS
20
GND
VCPU2(2.0V)
21
BEEP
VCPU1(2.5V)
22
MUTEMUTE_γ
DTC1D
23
PWR
SW
VCC1(2.5V)
24
BIAS
IN BIAS
INM1
BB
SW
INP1
BST
OUT
RF1
IC301 TA2120FN
5-8.
IC Pin Function Descriptions
• MAIN Board IC601 CXD3029R ( RF Amp, Digital Signal Processor, Digital Servo Processor )
Pin No.
Pin Name
I/O
Description
1
XRAS
O
DRAM row address strobe signal output
2
XWE
O
DRAM data input enable signal output
3
D1
I/O
DRAM data bus 1
4
D0
I/O
DRAM data bus 0
5
D3
I/O
DRAM data bus 3
6
D2
I/O
DRAM data bus 2
7
DCLK
O
Test pin Not used (open)
8
DCKE
O
9
XCAS
O
DRAM column address strobe signal output
10
WFCK/DQM
O
WFCK signal output Not used (open)
11 to 13
A9 to A7
O
DRAM address bus 9 to 7
14
DVSS
—
Ground (DRAM interface )
15 to 17
A6 to A4
O
18
XRDE
I/O
DRAM readout enable signal input
19
VDD0
—
Power supply (digital)
20
CLOK
I
Serial data transfer clock input from CPU
21
SDTO
I
Serial data input from CPU
22
SENS
O
SENS signal output to CPU
23
XLAT
I
Latch signal input from CPU
24
XSOE
I
CPU serial data output enable signal input
25
SYSM
I
Mute signal input ( “ H “: mute)
26
WDCK
O
Word clock output (f=2Fs)
27
SCOR
O
Output a high signal when either subcode sync S0 or S1 is detected
28
XRST
I
System reset ( “ L “ : reset)
Spindle motor external control input Not used
29
PWMI
I
30
XQOK
I/O
Subcode-Q OK signal input
31
XWRE
I/O
DRAM write enable signal input
32
R4M
O
Clock output for Microcomputer (open)
33
VSS0
—
Ground (digital)
34
SQCK
I
SQSO readout clock input (fixed at “H”)
35
SCLK
I
SENS serial data readout clock input (fixed at “H”)
36
SQSO
O
Subcode-Q 80-bit or PCM peak and level data output Not used (open)
37
XEMP
O
DRAM readout prohibited signal output Not used (open)
38
XWIH
O
DRAM write prohibited signal output Not used (open)
39
SBSO
O
Subcode P to W signal output Not used (open)
40
EXCK
I
SBSO readout clock input Not used (connected to ground)
Crystal selection input ( “L” : 16.9344MHz, “H” : 33.8688MHz) fixed at “L”
41
XTSL
I
42
HVSS
—
Ground (headphone)
43
HPL
O
PDM output for L-Ch headphone (open)
44
HPR
O
PDM output for R-Ch headphone (open)
45
HVDD
—
Power supply (headphone)
46
XVDD
—
Power supply (master clock)
47
XTAI
I
Crystal oscillation circuit input
48
XTAO
O
Crystal oscillation circuit output
49
XVSS
—
Ground (master clock)
50
AVDD1
—
Power supply (analog)
51
AOUT1
O
L-Ch analog output
52
VREFL
O
L-Ch reference voltage output
53
AVSS1
—
Ground (analog)
54
AVSS2
—
Ground (analog)
19
Pin No.
Pin Name
I/O
55
VREFR
O
R-Ch reference voltage output
Description
56
AOUT2
O
R-Ch analog output
57
AVDD2
—
58
TES1
I
Test pin (Normally connected to ground)
59
TEST
I
Test pin (Normally connected to ground)
60
VSS1
—
Ground (digital)
61
LRMU
O
L-Ch,R-Ch “0” detection flag (AND output)
62
DOUT
O
Digital Out output terminal (open)
63
ATSK
I/O
Anti-shock I/O Not used (open)
64
DFCT
I/O
Defect signal I/O Not used (open)
65
FOK
I/O
Focus OK signal I/O
66
MIRR
I/O
Mirror signal I/O Not used (open)
67
COUT
I/O
Track count signal I/O Not used (open)
68
C2PO
O
C2PO signal output Not used (open)
69
GFS
O
GFS signal output
70
XUGF
O
XUGF signal output Not used (open)
71
XPCK
O
XPCK signal output Not used (open)
72
VDD1
—
73
PCO
O
Master PLL charge pump output
74
FILI
I
Master PLL filter input
75
FILO
O
Master PLL filter output (slave = digital PLL)
76
CLTV
I
Multiplier VCO1 control voltage input
77
VCTL
I
Wide-band EFM PLL VCO2 control voltage input
78
VPCO
O
Wide-band EFM PLL charge pump output
79
AVSS3
—
Ground (analog)
80
ASYO
O
EFM full-swing output (“L” = VSS, “H” = VDD)
81
ASYI
O
Asymmetry comparator voltage output
Asymmetry circuit constant current input
82
BIAS
I
83
AVDD3
—
84
RFAC
I
85
AVDD0
—
EFM signal input
86
IGEN
I
87
AVSS0
—
Operational amplifier constant current input
Ground (analog)
88
RFDC
I
RF signal input
89
E
I
E signal input
90
F
I
F signal input
91
B
I
B signal input
92
A
I
A signal input
Center voltage input
93
VC
I
94
VSS2
—
Ground (digital)
95
FRDR
O
Focus drive output
96
FFDR
O
Focus drive output
97
TRDR
O
Tracking drive output
98
TFDR
O
Tracking drive output
99
SRDR
O
Sled drive output
100
SFDR
O
Sled drive output
101
SSTP
I
Disc innermost track detection signal input (connected to ground)
102
MDS
O
Spindle drive output
103
MDP
O
Spindle motor drive servo control signal output
104
C176
O
176.4kHz output
105
VDD2
—
106
LRCK_O
O
D/A interface LR clock output (f=Fs)
20
Pin No.
Pin Name
I/O
107
LRCK_I
I
D/A interface LR clock input
Description
108
PCMD_O
O
D/A interface Serial data output
109
PCMD_I
I
D/A interface Serial data input
110
BCK_O
O
D/A interface Bit clock output
111
BCK_I
I
D/A interface Bit clock input
112
DVDD
—
Power supply (DRAM interface)
113 to 116
A3 to A0
O
117
A10
O
DRAM address bus 10
118
A11
O
DRAM address bus 11 Not used (open)
119 to 120
A12,A13
O
21
• MAIN Board IC701 CXD9717R-002 (MP3 Decoder)
Pin No.
Pin Name
I/O
1
/RESET
I
Reset input terminal “L”: reset
Description
2
MIMD
I
Microcomputer interface mode selection input “H”: I2C, “L”: TSB
3
/MICS
I
Microcomputer interface chip select signal input (fixed at “L”)
4
/MILP
I
Microcomputer interface latch pulse input (fixed at “L”)
5
MIDIO
I/O
6
/MICK
I
Microcomputer interface serial clock input (SCL in I2C mode)
7
MIACK
O
Microcomputer interface acknowledge signal output (open)
8
VDDT
—
Power supply (3.3V) for digital circuit
9
SDO
O
Data output
10
BCKO
O
Bit clock output (open)
11
LRCKO
O
LR clock output (open)
12
SDI0
I
Data input 0
13
BCKIA
I
Bit clock input A
14
LRCKIA
I
LR clock input A
15
SDI1
I
Data input 1 (fixed at “L”)
16
BCKIB
I
Bit clock input B (fixed at “L”)
17
LRCKIB
I
LR clock input B (fixed at “L”)
18
VDD
—
19
STANDBY
I
20
VSS
—
Ground for digital circuit
21
VSSL
—
Ground for DAC Lch
22
VRAL
—
Reference voltage terminal for DAC Lch
23
LO
O
DAC Lch signal output (open)
24
VDAL
—
Power supply (2.5V) for DAC Lch
25
VDAR
—
Power supply (2.5V) for DAC Rch
Microcomputer interface serial data input/output (SDA in I2C mode)
Standby mode control signal input “H”: STB, “L”: normal
26
RO
O
DAC Rch signal output (open)
27
VRAR
—
Reference voltage terminal for DAC Rch
28
VSSR
—
Ground for DAC Rch
29
TESTP
I
Terminal for test “H”: test mode, “L”: normal (fixed at “L”)
30
TX0
O
SPDIF signal output (open)
31 to 34
PO0 to PO3
O
Genaeral purpose output 0 to 3 (open)
35
VDDT
—
36 to 38
PO4 to PO6
O
Genaeral purpose output 4 to 6 (open)
39
PO7
O
Genaeral purpose output 7 Interrupt request signal output to the system control (IC801)
40
VSS
—
41
AD13
I/O
External interrupt signal input (fixed at “L”)
42
VDDM
—
Power supply (2.5V) for internal 1Mbit SRAM
43 to 44
FI0 to FI1
I
45
VSSM
—
Ground for internal 1Mbit SRAM
46, 47
IO0,IO1
I/O
External DRAM data input/output (fixed at “L”)
48
VSS
—
49 to 51
IO2 to IO4
I/O
52
VDD
—
53
IO5
I/O
54
TSTIN
I
Test terminal (fixed at “L”)
55
FI2
I
Flag signal input 2 (fixed at “L”)
56
VSSP
—
Ground for VCO circuit
57
PDO
O
PLL phase error detection signal output
58
VCOI
I
VCO control voltage input
59
VDDP
—
22
Flag signal input 0 to 1
Power supply for VCO circuit (2.5V)
Pin No.
Pin Name
I/O
60
CKO
I/O
Audio clock output
Description
61
VDDX
—
Power supply (2.5V) for oscillation circuit
62
XI
I
Resonator terminal
63
XO
O
Resonator terminal
64
VSSX
—
Ground for oscillation circuit
23
• MAIN Board IC801 µPD784216AY-1700 (System Control)
Pin No.
Pin Name
I/O
1
STANDBY_O
O
Standby signal output to the MP3 decoder (IC701)
Description
2 to 8
NC
—
Not used (open)
9
VDD
—
Power supply
10
XTALO
O
System clock output (8MHz)
11
XTALI
I
System clock input (8MHz)
12
GND
—
Ground
13
NC
—
Not used (open)
14
GND
—
Ground
15
RESET
I
Reset signal input
16
SCOR_INT
I
Sub code signal input
17
GRSCOR_INT
I
GR SCOR signal input
18
OPENSW_INT
I
Open/close switch signal input
19
KEY_INT
I
Key input detection signal input
20
RMKEY_INT
I
Not used (fixed at “H”)
21
DCIN_INT
I
AC adaptor detection signal input
22
NC
—
Not used (open)
23
VDD(AVDD)
—
Power supply
24
VDD(AVREF0)
—
Power supply
25
BAT1MNT_AD
I
Battery (3V) detection input terminal
26
BAT2MNT_AD
I
Battery (1.5V) detection input terminal Not used (fixed at “L”)
27
CHGMNT_AD
I
Not used (fixed at “L”)
28
KEY1_AD
I
Key input terminal
29
KEY2_AD
I
Key input terminal
30
RMKEY_AD
I
31
DCINMNT_AD
I
AC adaptor voltage monitoring input terminal
32
NC
—
Not used (open)
33
GND(AVSS)
—
Ground
34
AGC_DA
O
AGC signal output (open)
35
NC
—
Not used (open)
36
VDD(AVREF1)
—
Power supply
37
TSBDTI
I
38
TSBDTO
O
Not used (open)
39
TSBSCK
I
Not used (open)
40
SENS
I
SENS signal input
41
SDTO
O
Serial data input
42
SCK
O
Serial data transfer clock signal input
43
MCLK
O
Not used (open)
44
BEEP_O
O
Beep signal output
45
SDAO(I2C)
O
Serial data output to the MP3 DSP
46
XSOE_O
O
SOE signal output to the IC601
47
SCLO(I2C)
O
Serial clock signal output
48
BXPOWLT_O
O
Power suplly on/off signal output
49
XAPCOFF_O
O
Automatic power off signal output
50
NC
I
Not used (fixed at “L” in French model)
51
AMUTE_O
O
Audio muting signal output
52
XLIGHT-ON
O
Back light on/off signal output
53
XRST_O
O
Reset signal output to the IC601
54
WAKEUP_O
O
Wake up signal output
55
XLAT
O
Latch signal output to the IC601
56 to 63
D0 to D7
O
LCD drive signal output
24
Pin No.
Pin Name
I/O
64
A0
O
LCD drive signal output
Description
65
NC
—
Not used (open)
66
XLIGHT_ON
—
Not used (open)
67 to 71
NC
—
Not used (open)
72
GND
—
Ground
73 to 76
NC
—
Not used (open)
77
RD
O
RD signal output to the LCD unit
78
WR1
O
WR1 signal output to the LCD unit
79, 80
NC
—
Not used (open)
81
VDD
—
Power supply
82
XQOK_O
O
Q signal OK output to the IC601
83
TSB_RW_O
O
AGC PWM signal output
84
TSBLAT_O
O
Not used (open)
85
BUSY_I
I
Not used (open)
86
FOK_I
I
FOK signal input from the IC601
87
GFS_I
I
GFS signal input from the IC601
88
GPRO_I
I
G-protection switch signal input
89
XWRE_O
O
WRE signal output to the IC601
90
HOLD_I
I
Hold switch signal input
91
LINEIN_I
I
Not used (open)
92
XRDE_O
O
RDE signal output to the IC601
93
TESTMODE_I
I
Test mode setting terminal
94
GND
—
Ground
95
OPSTB
O
Standby signal output to the CD mechanism deck
96
MP3_DSP_RST
O
MP3 DSP reset signal output to the IC701
97
LCD_RST_O
O
Reset signal output to the LCD unit
98
MP3DSP_I
I
MP3 DSP status signal input
99
NC
—
Not used (open)
100
OPGSW
O
Optical pick-up gain control signal output
25
SECTION 6
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Accessories are given in the last of the electrical parts list.
• Abbreviation
FR : French model
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
6-1. Cabinet (Front) Section
2
7
1
6
cabinet (lower) section
4
7
3
5
Ref. No.
Part No.
Description
1
1
1
2
2
X-3382-194-1
X-3382-195-1
X-3382-196-1
X-3382-060-1
X-3382-061-1
CABINET (UPPER) SUB ASSY (CJ500)
CABINET (UPPER) SUB ASSY (CJ501)
CABINET (UPPER) SUB ASSY (CJ506CK)
LID ASSY, UPPER (CJ501)
LID ASSY, UPPER (CJ500)
2
X-3382-063-1 LID ASSY, UPPER (CJ506CK)
26
Remarks
Ref. No.
Part No.
Description
3
4
4
5
6
3-231-037-21
3-231-897-01
3-231-897-11
3-240-250-01
3-232-612-01
LID, BATTERY CASE
BUTTON (OPEN) (CJ500/CJ501)
BUTTON (OPEN) (CJ506CK)
BUTTON
KNOB (JOGGABLE)
7
3-336-395-01 SCREW (B2X10) (G), TAPPING
Remarks
Ver 1.1 2002.05
6-2. Cabinet (Lower) Section
CDM-3152ER
51
52
51
51
LCD801
65
64
63
53
BT402
BT400
56
62
57
58
not
supplied
59
61
Description
60
Ref. No.
Part No.
51
* 52
* 52
52
53
4-222-765-11 INSULATOR
A-3021-790-A MAIN BOARD, COMPLETE (CJ506CK)
A-3323-903-A MAIN BOARD, COMPLETE
(CJ500/CJ501:EXCEPT FR)
A-3323-904-A MAIN BOARD, COMPLETE (CJ501:FR)
3-240-252-01 HOLDER (LCD) (CJ500/CJ501)
53
56
57
58
59
3-240-252-11
4-218-592-01
3-231-676-01
3-222-862-01
X-3382-059-1
HOLDER (LCD) (CJ506CK)
CUSHION
TERMINAL (LINK 4), BATTERY
SPRING (TORSION)
CABINET (LOWER) SUB ASSY
Remarks
Ref. No.
Part No.
Description
60
61
62
63
64
3-222-857-01
4-974-607-11
3-242-794-01
3-234-025-01
3-240-253-01
KNOB (HOLD)
FOOT, RUBBER
SHEET, SHIELD
SHEET, INSULATING
PLATE, LIGHT GUIDE (CJ506CK)
65
BT400
BT402
LCD801
3-240-254-01
3-222-860-01
3-231-411-01
1-804-652-21
Remarks
ILLUMINATOR (CJ506CK)
TERMINAL (+.-), BATTERY
TERMINAL (-), BATTERY
DISPLAY PANEL, LIQUID CRYSTAL
(CJ500/CJ501)
LCD801 1-804-652-11 DISPLAY PANEL, LIQUID CRYSTAL (CJ506CK)
27
6-3. Optical Pick-up Section (CDM-3125ER)
102
106
M901
107
108
109
104
105
110
112
111
113
103
M902
101
102
Ref. No.
Part No.
Description
101
102
103
104
105
4-218-821-01
3-318-203-71
A-3052-902-A
4-218-823-01
4-218-825-01
COVER, GEAR
SCREW (B1.7X5), TAPPING
FEED ASSY, SCREW
GEAR (B)
SPRING, SLED
106
107
108
0 109
110
3-235-420-01
4-218-827-02
3-686-458-03
X-3380-950-1
3-235-418-01
CHASSIS
RETAINER, SHAFT
SCREW (P1.4X3.5), TAPPING
OPTICAL PICK-UP (DAX-25E)
RACK
28
Remarks
Ref. No.
111
112
113
M901
M902
Part No.
Description
3-348-998-81
4-220-645-02
4-964-564-01
A-3052-904-A
A-3328-627-A
SCREW (M1.4)
SHAFT, STANDARD
SCREW (M1.2X1.6)
MOTOR ASSY, TURN TABLE (SPINDLE)
MOTOR ASSY, SLED (SLED)
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Remarks
pour la sécurité.
pièce portant le numéro spécifié.
SECTION 7
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts specified in the diagrams or the components used
on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
• Abbreviation
CND : Canadian model
E13 : 220-230V AC area in E model
E92 : Chilean and Peruvian model
EE : East European model
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. .
uPA. . : µPA. .
uPB. . : µPB. .
uPC. . : µPC. .
uPD. . : µPD. .
• CAPACITORS
uF: µF
• COILS
uH: µH
Ver 1.1 2002.05
MAIN
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
When indicating parts by reference number,
please include the board name.
FR : French model
AR : Argentine model
AUS : Australian model
Ref. No.
Part No.
Remarks
Ref. No.
Part No.
Description
*
A-3021-790-A MAIN BOARD, COMPLETE (CJ506CK)
******************************
A-3323-903-A MAIN BOARD, COMPLETE
(CJ500/CJ501:EXCEPT FR)
**************************************
A-3323-904-A MAIN BOARD, COMPLETE (CJ501:FR)
*******************************
C411
C412
C413
C414
C415
1-125-837-91
1-127-760-11
1-125-837-91
1-124-584-00
1-124-584-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
1uF
4.7uF
1uF
100uF
100uF
10%
10%
10%
20%
20%
6.3V
6.3V
6.3V
10V
10V
C416
C417
C418
C419
C420
1-162-919-11
1-162-964-11
1-162-970-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22PF
0.001uF
0.01uF
0.1uF
0.1uF
5%
10%
10%
50V
50V
25V
25V
25V
C421
C422
C423
C424
C425
1-162-966-11
1-164-156-11
1-164-156-11
1-137-934-91
1-124-584-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
ELECT
0.0022uF 10%
0.1uF
0.1uF
47uF
20%
100uF
20%
50V
25V
25V
10V
10V
C426
C429
C430
C431
C432
1-162-970-11
1-124-589-11
1-164-156-11
1-162-927-11
1-164-505-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
47uF
0.1uF
100PF
2.2uF
25V
16V
25V
50V
16V
C433
C434
C435
C436
C437
1-124-233-11
1-125-837-91
1-124-589-11
1-124-589-11
1-162-923-11
ELECT
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
10uF
1uF
47uF
47uF
47PF
20.00%
10%
20%
20%
5%
16V
6.3V
16V
16V
50V
C438
C439
C440
C441
C443
1-107-823-11
1-162-923-11
1-164-230-11
1-126-369-11
1-162-919-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.47uF
47PF
220PF
220uF
22PF
10.00%
5%
5.00%
20%
5%
16V
50V
50V
6.3V
50V
C444
C445
C446
C447
C500
1-162-927-11
1-125-837-91
1-125-837-91
1-162-964-11
1-125-837-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
1uF
1uF
0.001uF
1uF
5%
10%
10%
10%
10%
50V
6.3V
6.3V
50V
6.3V
C501
C601
C602
C604
C605
1-124-234-00
1-162-927-11
1-162-915-11
1-107-826-11
1-162-964-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22uF
100PF
10PF
0.1uF
0.001uF
20%
5%
0.5PF
10.00%
10%
16V
50V
50V
16V
50V
*
*
3-234-025-01
3-240-252-01
3-240-252-11
3-240-253-01
3-240-254-01
Description
SHEET, INSULATING
HOLDER (LCD) (CJ500/CJ501)
HOLDER (LCD) (CJ506CK)
PLATE, LIGHT GUIDE (CJ506CK)
ILLUMINATOR (CJ506CK)
< BATTERY TERMINAL>
BT400
BT402
3-222-860-01 TERMINAL (+.–), BATTERY
3-231-411-01 TERMINAL (–), BATTERY
< CAPACITOR >
C102
C103
C104
C202
C203
1-162-964-11
1-164-505-11
1-107-826-11
1-162-964-11
1-164-505-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
2.2uF
0.1uF
0.001uF
2.2uF
10%
50V
16V
10.00% 16V
10%
50V
16V
C204
C301
C302
C303
C304
1-107-826-11
1-126-369-11
1-125-838-11
1-124-233-11
1-124-233-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
ELECT
0.1uF
220uF
2.2uF
10uF
10uF
10.00%
20%
10%
20.00%
20.00%
C305
C306
C401
C402
C403
1-115-467-11
1-125-837-91
1-115-156-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.22uF
1uF
1uF
0.01uF
0.01uF
10.00% 10V
10%
6.3V
10V
10%
25V
10%
25V
C404
C405
C406
C407
C409
1-164-156-11
1-115-156-11
1-162-964-11
1-115-467-11
1-124-233-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.1uF
1uF
0.001uF
0.22uF
10uF
25V
10V
10%
50V
10.00% 10V
20.00% 16V
16V
6.3V
6.3V
16V
16V
Remarks
10%
20%
5%
29
MAIN
Ref. No.
Part No.
Description
C606
C607
C608
C609
C610
1-107-823-11
1-107-823-11
1-162-964-11
1-119-750-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
0.47uF
0.47uF
0.001uF
22uF
0.1uF
10.00%
10.00%
10%
20.00%
16V
16V
50V
6.3V
25V
Remarks
C611
C612
C613
C614
C615
1-162-962-11
1-162-962-11
1-162-962-11
1-162-962-11
1-119-750-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
470PF
470PF
470PF
470PF
22uF
10%
10%
10%
10%
20.00%
50V
50V
50V
50V
6.3V
C616
C617
C618
C619
C621
1-124-584-00
1-164-156-11
1-119-750-11
1-162-923-11
1-115-156-11
ELECT
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.1uF
22uF
47PF
1uF
20%
C622
C623
C624
C626
C627
1-107-826-11
1-801-862-11
1-125-837-91
1-162-962-11
1-162-964-11
CERAMIC CHIP
VARISTOR, CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
10.00% 16V
1uF
470PF
0.001uF
10%
10%
10%
6.3V
50V
50V
C628
C629
C631
C701
C703
1-162-927-11
1-107-826-11
1-162-970-11
1-162-964-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
0.1uF
0.01uF
0.001uF
0.1uF
5%
10.00%
10%
10%
50V
16V
25V
50V
25V
C704
C707
C708
C709
C710
1-164-156-11
1-164-156-11
1-162-970-11
1-115-467-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.01uF
0.22uF
0.1uF
25V
25V
10%
25V
10.00% 10V
25V
C711
C712
C713
C714
C715
1-135-259-11
1-135-259-11
1-164-156-11
1-162-964-11
1-164-156-11
TANTAL. CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
10uF
0.1uF
0.001uF
0.1uF
20.00% 6.3V
20.00% 6.3V
25V
10%
50V
25V
C716
C803
C804
C806
C807
1-107-826-11
1-164-156-11
1-164-156-11
1-164-156-11
1-125-837-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
1uF
10.00% 16V
25V
25V
25V
10%
6.3V
C808
C809
C810
C811
C813
1-164-156-11
1-124-233-11
1-164-156-11
1-162-970-11
1-164-156-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
10uF
0.1uF
0.01uF
0.1uF
25V
20.00% 16V
25V
10%
25V
25V
C814
C815
C817
C818
C819
1-125-837-91
1-125-837-91
1-125-837-91
1-125-837-91
1-125-837-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
1uF
1uF
1uF
10%
10%
10%
10%
10%
6.3V
6.3V
6.3V
6.3V
6.3V
C820
C821
1-164-156-11 CERAMIC CHIP
1-162-970-11 CERAMIC CHIP
10%
25V
25V
10V
25V
20.00% 6.3V
5%
50V
10V
Ref. No.
Part No.
Description
Remarks
< DIODE >
D402
D403
D404
D405
D405
8-719-081-83
8-719-081-83
8-719-072-70
8-719-976-96
8-719-083-60
DIODE
DIODE
DIODE
DIODE
DIODE
CRS03(TE85L)
CRG01(TE85L)
MA2ZD14001S0
UDZ-TE-17-4.7B
UDZSTE-174.7B
D406
D407
D408
D409
D410
8-719-404-50
8-719-072-70
8-719-058-24
8-719-072-70
8-719-072-70
DIODE
DIODE
DIODE
DIODE
DIODE
MA111-TX
MA2ZD14001S0
RB501V-40TE-17
MA2ZD14001S0
MA2ZD14001S0
D411
D412
D801
D802
8-719-072-70
8-719-420-87
8-719-044-74
8-719-970-49
DIODE
DIODE
DIODE
DIODE
MA2ZD14001S0
MA8130-TX
MA792WK-TX
BR4361F (LCD BACK LIGHT) (CJ506CK)
< FERRITE BEAD >
FB801
1-216-864-11 METAL CHIP
0
5%
1/16W
< IC >
0.1uF
0.01uF
< CONNECTOR >
* CN501
CN502
CN503
30
1-816-237-21 CONNECTOR 15P
1-784-342-21 HOUSING, CONNECTOR 2P
1-784-342-11 HOUSING, CONNECTOR 2P
IC301
IC401
IC402
IC403
IC601
8-759-681-65
8-759-714-74
6-700-465-01
8-759-594-55
8-752-410-68
IC
IC
IC
IC
IC
TA2120FN(EL)
TB2125F
XC6383A301MR
TC75S57F(TE85R)
CXD3029R
IC602
IC701
IC703
IC801
IC802
6-700-195-01
6-702-068-01
8-759-655-22
6-801-429-01
6-700-466-01
IC
IC
IC
IC
IC
MSM51V17400F-10TK-FS
CXD9717R-002
TC7WH34FK(TE85R)
uPD784216AY-1700
XC61CC2102MR
IC803
IC804
8-759-655-22 IC TC7WH34FK(TE85R)
8-759-655-22 IC TC7WH34FK(TE85R)
< JACK >
J301
J401
1-565-287-41 JACK (i)
1-778-153-21 JACK,DC(POLARITY UNIFIED TYPE) (DC IN 4.5V)
< COIL >
L101
L201
L301
L401
L402
1-414-760-21
1-414-760-21
1-410-389-31
1-412-056-11
1-412-056-11
FERRITE
FERRITE
INDUCTOR CHIP
INDUCTOR
INDUCTOR
0uH
0uH
47uH
4.7uH
4.7uH
L403
L404
L405
L406
L407
1-414-398-11
1-419-387-21
1-410-389-31
1-410-389-31
1-400-145-21
INDUCTOR
INDUCTOR
INDUCTOR CHIP
INDUCTOR CHIP
INDUCTOR
10uH
100uH
47uH
47uH
47uH
L408
L409
L410
L411
L601
1-400-145-21
1-410-389-31
1-410-389-31
1-410-389-31
1-414-398-11
INDUCTOR
INDUCTOR CHIP
INDUCTOR CHIP
INDUCTOR CHIP
INDUCTOR
47uH
47uH
47uH
47uH
10uH
L603
L604
1-469-570-21 INDUCTOR
1-216-864-11 METAL CHIP
10uH
0
5%
1/16W
MAIN
Ref. No.
Part No.
Description
Remarks
Ref. No.
Part No.
Description
LCD801 1-804-652-11 DISPLAY PANEL, LIQUID CRYSTAL (CJ506CK)
LCD801 1-804-652-21 DISPLAY PANEL, LIQUID CRYSTAL
(CJ500/CJ501)
R433
R434
R435
R437
R438
1-218-895-11
1-218-903-11
1-216-829-11
1-216-853-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
220K
4.7K
470K
47K
0.5%
0.5%
5%
5%
5%
1/10W
1/10W
1/16W
1/16W
1/16W
R439
R440
R441
R442
R444
1-216-841-11
1-216-857-11
1-216-841-11
1-216-864-11
1-216-853-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
1M
47K
0
470K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R445
R446
R447
R448
R450
1-216-845-11
1-216-857-11
1-216-841-11
1-216-857-11
1-414-760-21
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
FERRITE
100K
1M
47K
1M
0uH
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R451
R452
R453
R457
R458
1-414-760-21
1-414-760-21
1-216-853-11
1-216-845-11
1-216-845-11
FERRITE
FERRITE
METAL CHIP
METAL CHIP
METAL CHIP
0uH
0uH
470K
100K
100K
5%
5%
5%
1/16W
1/16W
1/16W
R459
R460
R461
R462
R463
1-216-817-11
1-216-841-11
1-469-152-11
1-469-152-11
1-216-295-91
METAL CHIP
METAL CHIP
FERRITE
FERRITE
SHORT
470
47K
0uH
0uH
0
5%
5%
1/16W
1/16W
R464
R465
R466
R467
R468
1-216-833-11
1-216-833-11
1-216-837-11
1-216-837-11
1-216-295-91
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT
10K
10K
22K
22K
0
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R469
R470
R501
R601
R602
1-216-864-11
1-216-864-11
1-216-864-11
1-216-837-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
22K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R603
R604
R605
R606
R607
1-216-837-11
1-216-845-11
1-216-837-11
1-216-845-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
100K
22K
100K
22K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R609
R611
R612
R613
R614
1-216-837-11
1-216-829-11
1-216-829-11
1-216-833-11
1-216-857-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
4.7K
4.7K
10K
1M
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R615
R616
R617
R618
R619
1-216-853-11
1-216-833-11
1-216-853-11
1-216-809-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470K
10K
470K
100
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R620
R622
R623
R624
R625
1-216-864-11
1-218-895-11
1-218-895-11
1-216-017-91
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
0
100K
100K
47
22K
5%
0.5%
0.5%
5%
5%
1/16W
1/10W
1/10W
1/10W
1/16W
< LIQUID CRYSTAL DISPLAY >
< TRANSISTOR >
Q401
Q402
Q403
Q404
Q405
8-729-807-34
8-729-028-97
8-729-427-74
8-729-026-53
8-729-905-40
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SB1188-T100-QR
DTC114TUA-T106
XP4601-TXE
2SA1576A-T106-QR
2SC4081T106
Q406
Q407
Q408
Q409
Q410
8-729-922-10
8-729-047-36
8-729-905-40
8-729-047-36
8-729-047-36
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1577-T106-QR
CPH3303-TL
2SC4081T106
CPH3303-TL
CPH3303-TL
Q701
Q801
Q802
Q803
Q804
8-729-029-15
8-729-029-15
8-729-026-53
8-729-026-53
8-729-924-65
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC144TUA-T106
DTC144TUA-T106
2SA1576A-T106-QR
2SA1576A-T106-QR
DTC123YUA-T106 (CJ506CK)
< RESISTOR >
R101
R102
R104
R105
R201
1-216-841-11
1-216-821-11
1-216-833-11
1-216-793-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
47K
1K
10K
4.7
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/10W
1/16W
R202
R203
R204
R301
R303
1-216-821-11
1-216-793-11
1-216-833-11
1-414-813-11
1-216-864-11
METAL CHIP
RES-CHIP
METAL CHIP
FERRITE
METAL CHIP
1K
4.7
10K
0uH
0
5%
5%
5%
1/16W
1/10W
1/16W
5%
1/16W
R402
R403
R404
R405
R406
1-218-895-11
1-218-895-11
1-218-903-11
1-218-887-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
220K
47K
47K
0.5%
0.5%
0.5%
0.5%
5%
1/10W
1/10W
1/10W
1/10W
1/16W
R407
R408
R413
R414
R415
1-216-845-11
1-216-845-11
1-216-813-11
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
220
10K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R416
R417
R418
R419
R420
1-216-821-11
1-216-789-11
1-216-833-11
1-216-821-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
2.2
10K
1K
22K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R421
R422
R423
R424
R425
1-216-821-11
1-216-833-11
1-216-853-11
1-216-841-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10K
470K
47K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R426
R428
R430
R431
R432
1-216-864-11
1-216-849-11
1-216-857-11
1-216-833-11
1-218-903-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
220K
1M
10K
220K
5%
5%
5%
5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/10W
Remarks
31
MAIN
Ref. No.
Part No.
Description
Part No.
Description
R626
R627
R628
R629
R630
1-216-833-11
1-216-837-11
1-216-833-11
1-216-829-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
22K
10K
4.7K
2.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R737
R738
R739
R740
R741
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R631
R632
R633
R634
R635
1-216-833-11
1-216-829-11
1-216-833-11
1-216-829-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
4.7K
10K
4.7K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R742
R746
R747
R801
R802
1-216-853-11
1-216-853-11
1-216-864-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470K
470K
0
100K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R636
R637
R638
R639
R640
1-216-829-11
1-216-833-11
1-216-829-11
1-216-833-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
10K
4.7K
10K
4.7K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R803
R804
R805
R806
R807
1-216-864-11
1-216-853-11
1-216-837-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
470K
22K
100K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R641
R642
R643
R644
R645
1-216-837-11
1-216-833-11
1-216-864-11
1-414-760-21
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
FERRITE
METAL CHIP
22K
10K
0
0uH
10K
5%
5%
5%
1/16W
1/16W
1/16W
5%
1/16W
R808
R809
R810
R811
R812
1-216-833-11
1-216-864-11
1-216-829-11
1-216-857-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
0
4.7K
1M
0
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R646
R651
R652
R653
R654
1-216-833-11
1-216-833-11
1-216-833-11
1-216-857-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
1M
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R813
R814
R815
R816
R817
1-216-833-11
1-216-821-11
1-216-829-11
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
4.7K
10K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R701
R702
R703
R705
R706
1-216-864-11
1-216-853-11
1-216-853-11
1-216-853-11
1-216-853-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
470K
470K
470K
470K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R818
R819
R820
R822
R823
1-216-829-11
1-216-833-11
1-216-864-11
1-216-849-11
1-216-849-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
10K
0
220K
220K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R707
R708
R710
R711
R712
1-801-862-11
1-216-853-11
1-216-845-11
1-216-853-11
1-216-853-11
VARISTOR, CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470K
100K
470K
470K
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R824
R825
1-216-864-11 METAL CHIP
1-216-805-11 METAL CHIP
0
47
5%
5%
R826
R827
R828
1-216-864-11 METAL CHIP
1-216-864-11 METAL CHIP
1-216-864-11 METAL CHIP
0
0
0
5%
5%
5%
R713
R714
R715
R716
R717
1-216-845-11
1-216-821-11
1-216-864-11
1-216-864-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
1K
0
0
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
(CJ506CK)
1/16W
1/16W
1/16W
(CJ501:FR)
R829
R830
R831
1-216-833-11 METAL CHIP
1-216-833-11 METAL CHIP
1-216-864-11 METAL CHIP
10K
10K
0
5%
5%
5%
R718
R719
R720
R722
R723
1-216-853-11
1-216-853-11
1-216-853-11
1-216-821-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470K
470K
470K
1K
4.7K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
RV301
R724
R725
R726
R727
R728
1-216-853-11
1-216-853-11
1-216-853-11
1-216-853-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470K
470K
470K
470K
220
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
S801
S802
S803
S804
S805
1-692-440-11
1-553-977-00
1-762-078-11
1-692-014-11
1-692-014-11
SWITCH, PUSH (CD DOOR OPEN)
SWITCH, SLIDE (G-PRO)
SWITCH, SLIDE (HOLD .)
SWITCH, KEY BOARD (MENU)
SWITCH, KEY BOARD (DISPLAY)
R729
R730
R731
R732
R734
1-216-813-11
1-216-853-11
1-216-857-11
1-414-760-21
1-216-853-11
METAL CHIP
METAL CHIP
METAL CHIP
FERRITE
METAL CHIP
220
470K
1M
0uH
470K
5%
5%
5%
1/16W
1/16W
1/16W
5%
1/16W
S806
S807
S808
S809
S810
1-692-014-11
1-692-014-11
1-692-014-11
1-692-014-11
1-692-014-11
SWITCH, KEY BOARD (FOLDER +)
SWITCH, KEY BOARD (FOLDER -)
SWITCH, KEY BOARD (B >)
SWITCH, KEY BOARD (x)
SWITCH, KEY BOARD (.)
S811
1-692-014-11 SWITCH, KEY BOARD (SOUND)
32
Remarks
Ref. No.
Remarks
1/16W
1/16W
1/16W
< VARIABLE RESISTOR >
1-225-953-11 RES, VAR, MAIN CARBON 10K/10K (VOLUME w)
< SWITCH >
Ver 1.1 2002.05
MAIN
Ref. No.
Part No.
Description
Remarks
Ref. No.
Part No.
< VARISTOR >
VDR101
VDR201
VDR301
VDR401
VDR402
1-801-862-11
1-801-862-11
1-801-862-11
1-801-862-11
1-801-862-11
VARISTOR, CHIP
VARISTOR, CHIP
VARISTOR, CHIP
VARISTOR, CHIP
VARISTOR, CHIP
Remarks
MISCELLANEOUS
***************
0 109
X-3380-950-1 OPTICAL PICK-UP (DAX-25E)
M901
A-3052-904-A MOTOR ASSY, TURN TABLE (SPINDLE)
M902
A-3328-627-A MOTOR ASSY, SLED (SLED)
**************************************************************
VDR403 1-801-862-11 VARISTOR, CHIP
VDR601 1-801-862-11 VARISTOR, CHIP
ACCESSORIES
************
< VIBRATOR >
X601
1-795-218-21 VIBRATOR, CERAMIC 16.9MHz
X801
1-795-313-21 VIBRATOR, CERAMIC 8MHz
**************************************************************
Description
0
0
0
0
0
0
1-251-696-11
1-476-845-11
1-476-848-11
1-476-849-11
1-476-850-11
CONNECTING PACK, CAR (CJ506CK)
ADAPTOR, AC (AC-ES455) (CJ501:AEP,FR,EE,E13)
ADAPTOR, AC (AC-ES455) (CJ501:UK)
ADAPTOR, AC (AC-ES455) (CJ501:AR)
ADAPTOR, AC (AC-ES455) (CJ506CK:AUS)
1-476-851-11 ADAPTOR, AC (AC-ES455)
(CJ501:CND,E92/CJ506CK:US)
1-784-619-52 CORD, CAR BATTERY (CJ506CK)
3-240-972-11 MANUAL, INSTRUCTION (SPANISH)
(CJ501:AEP,E92,AR)
3-240-972-21 MANUAL, INSTRUCTION (ENGLISH)
(CJ501:CND,AEP,UK,EE,E92,AR)
3-240-972-31 MANUAL, INSTRUCTION (FRENCH)
(CJ501:CND,AEP,FR)
3-240-972-41 MANUAL, INSTRUCTION (DUTCH)
(CJ501:AEP,EE)
3-240-972-51 MANUAL, INSTRUCTION (SWEDISH)
(CJ501:AEP)
3-240-972-61 MANUAL, INSTRUCTION (PORTUGUESE)
(CJ501:AEP,E92)
3-240-972-71 MANUAL, INSTRUCTION (GERMAN) (CJ501:AEP)
3-240-972-81 MANUAL, INSTRUCTION (ITALIAN) (CJ501:AEP)
3-240-972-91
3-240-973-11
3-240-973-21
3-240-974-11
3-240-974-21
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
pour la sécurité.
pièce portant le numéro spécifié.
MANUAL, INSTRUCTION (FINNISH) (CJ501:AEP)
MANUAL, INSTRUCTION (CHINESE) (CJ501:E13)
MANUAL, INSTRUCTION (ENGLISH) (CJ501:E13)
MANUAL, INSTRUCTION (RUSSIAN) (CJ501:EE)
MANUAL, INSTRUCTION (CZECH) (CJ501:EE)
3-240-974-31 MANUAL, INSTRUCTION (HUNGARIAN)
(CJ501:EE)
3-240-974-41 MANUAL, INSTRUCTION (POLISH) (CJ501:EE)
3-240-974-51 MANUAL, INSTRUCTION (SLOVAK) (CJ501:EE)
3-240-974-61 MANUAL, INSTRUCTION (ENGLISH) (CJ500)
(CJ506CK:US)
(CJ506CK:AUS)
8-954-007-93 RECEVER, EAR MDR-027LP/1 SET
(CJ500/CJ506CK:US)
8-954-008-92 RECEIVER, EAR MDR-E808LP/C SET
(CJ501/CJ506CK:AUS)
33
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.
Date
Description of Revision
1.0
2002.03
New
1.1
2002.05
Addition of E13 and AEP models for D-CJ501
Addition of Australian model for D-CJ506CK
Change of the supply form of service parts
(ENG-02017)

D-CJ500/CJ501/CJ506CK - Vintage

Transcription

Similar documents

Pestalozzi

CDX-C90 -- Service Manual

JE320 - Minidisc.org