pneumatic tools

PNEUMATIC TOOLS
Couplers
08 - Filter, Regulator, Lubricator
Art. No. 00699…
Art. No. 00699 003 12 - 1/2”
The wall fitting will determine which
Art. No. 00699 003 14 - 1/4”
of the displayed couplers will be most suitable for receiv-
When choosing the F,R,L it is important to ascertain
ing the air hose.
what tools the customer will be using and what flow
It is important to note that there are numerous types of
rate he will require i.e. 1” Impact Wrench (307 l/min),
couplers in the market and these cannot be mixed i.e.
uses far more air than a 1/2” Impact Wrench (102 l/
Type 14 couplers can only be used with type 14 couplers.
min) would.
It is also important to note that the regulator should be located as
close as possible to the user. The oil mist is transported optimally up
to 5 meters. The working pressure drops with an increase in length of
the air hose.
In a workshop scenario as depicted below, a number of 1/2” F, R, L
Compressor
When selecting a compressor, it is important
that the capacity of air it produces is sufficient
to run your air tools. Most compressors will
have the pressure to start an air tool, but not
necessarily the volume to maintain running
the tool.
Volume is defined as cfm (cubic feet per minute) or l/min (litres per minute), and should
in most cases be available on the compressor
itself or within the technical information
supplied.
Determining your power requirements of an air compressor
There are two main considerations with regards to air compressor power requirements; determining the air flow required and selecting the tank size.
Air flow required
Compressors are measured in two main ways, PSI (pounds per square inch) and deliverable CFM (cubic feet per minute). These measurements determine the effectiveness of
the air compressor in different situations. When selecting a compressor you need to identify the PSI and CFM requirements of your air tools. If you will only be using one tool at
a time use the tool with the highest PSI and CFM requirement. If you intend to run multiple tools at the same time you will need to total the CFM's required by each tool.
The key is to choose an air compressor that exceeds the PSI and CFM airflow requirements of your highest rated air tool. That way you're sure to not be under-powered. The best
results are obtained when you purchase a compressor with 1.25 to 1.5 times more CFM airflow at the recommended PSI than your air tool(s) require. This method will ensure
the performance of your air tool(s) will be maintained without over working the compressor and losing efficiency.
Examples
Single tool use: If a 1/2" impact wrench requires *5.0 CFM (141.64 l/min) @ **90 PSI (6.2 Bar), then the compressor should deliver between 6.25 - 7.5 CFM @ 90 PSI.
Multiple tool use: If you plan to run more than one tool at the same time, you must add the CFM of each tool together to determine your needs. If your compressor needed to
power a Cut Off Tool (4 CFM @ 90 PSI) and a High Speed Grinder (4 CFM @ 90 PSI) you should look for a compressor that can deliver 10 - 12 CFM @ 90 PSI or higher.
*Converting CFM to l/min: 1 cfm = 28.328 l/min
**Converting PSI to Bar: PSI/14.5 = Bar
1
PNEUMATIC TOOLS
DSS 1/2” H Impact Wrench
Art. No. 00703 736 0
High-performance: up to 569 Nm releasing torque.
Tightening torque adjustable in four stages; irrespective of this, full releasing torque always applied.
Conducting of exhaust air through the handle with seat
for exhaust-air system (Art. 0703 735 001).
Practical reversing piston permits one handed operation.
High-performance impact mechanism with fast build-up
of torque, almost vibration-free, even when loaded.
Impact mechanism in oil tank = increased service life
through constant lubrication.
Square Drive
1/2”
Operating Torque in Nm*
420*
Max. Tightening Torque in Nm
470
Max. Releasing Torque in Nm
569
Operating Pressure in Bar
6.3
Weight
Stage
Tightening Torque in Nm
2.3Kgs
1
Approx. 70
Length
187mm
2
120
* The operating torque is the torque usually achieved under average
Air Consumption
102 l/min
3
280
working conditions. It depends on the highly varying ambient conditions (air pressure, hose diameter, soiling, etc.)
Coupler Size
1/4”
4
420
Ergonomic handle, balanced centre of gravity position
and handling.
DSS 3/4” H Impact Wrench
Art. No. 00703 773 0
Recommended maximum bolt size: M27.
Ideal for changing tires on utility
vehicles.
Well-balanced device in rugged aluminium housing.
Square Drive
3/4”
Operating Torque in Nm*
350-1440*
Max. Releasing Torque in Nm
1500
Operating Pressure in Bar
6.3
The handle does not become cool during work.
The device is very handy and user-friendly.
Weight
4.73Kgs
Dimensions (l x w x h)
High-quality pin impact mechanism in oil tank with six-vane
motor.
Long service life and optimum distribution of centre of gravity.
Rubber-coated and ergonomically shaped handle.
User-friendly right/left rotation switching and adjustable
trigger.
Increased service life thanks to constant lubrication.
Nearly vibration-free.
Stage
Tightening Torque in Nm
261x87x227mm
1
350
Air Consumption
215 l/min
2
685
Coupler Size
3/8”
3
1300
Noise Level (dB)
96
4
1440
2
PNEUMATIC TOOLS
DSS 1” H Impact Wrench
Art. No. 00703 770 0
Rugged aluminium housing.
Long service life.
Ergonomically shaped handle, 360°-
Square Drive
1”
rotatable additional handle, user-friendly
Operating Torque in Nm*
1152-2168
clockwise/ counter clockwise switching and adjustable
Max. Releasing Torque in Nm
2846
trigger.
Operating Pressure in Bar
6.3
Weight
13.06Kgs
Dimensions (l x w x h)
529x175.9x213.6
The device is very handy and user-friendly.
mm
Air Consumption
400 l/min
Coupler Size
1/2”
Noise Level (dB)
100
Stage
Tightening Torque in Nm
1
1152
2
1762
3
2168
Hand Held Polisher and Sander
Art. No. 00703 233 0 - Polisher (A.) - (2333)
Art. No. 00703 232 0 - Sander (B.) - (2333)
Ergonomic, rubber-coated handle.
Comfortable and slip-resistant.
Light, compact design.
Fatigue-free working and excellently suited for tight
spaces.
A.
With speed control.
Optimum adjustment to application.
Sound-dampened air outlet at the end of the handle.
No air outlet in the working area.
Large-sized and comfortable setting adjustment valve.
Optimized operating convenience.
Polisher/ Sander
Arbor
M6
Speed
2500/15000rpm
Weight
0.5Kgs
Operating Pressure in Bar
6.3
Air Consumption
113 l/min
Coupler Size
1/2”
Output in Watts
224
3
B.
PNEUMATIC TOOLS
DPM 250 Pneumatic Polisher
Art. No. 00703 000 870
Powerful 600 Watt motor with air exhaust through
the handle.
Rubberized grip area for comfortable handling.
Speed easily controllable by means of lever valve.
Disc Ø
No-load speed/min¯¹
Operating Pressure in Bar
Weight
Length
Air Consumption
Coupler Size
Hose Diameter
7” = 175mm
2500
6.3
1.9Kgs
307mm
91 l/min
1/4”
9mm
DST 380 Standard Reciprocating Saw
Art. No. 00703 882
Art. No. 00696 9...Flat Mount Blades for 00703 882
Safety valve lever prevents accidental switch on.
Rubber-coated handle area for pleasant working conditions.
Saw blade can be turned 180° for working overhead.
Integrated power control for respective application.
Adjustable guide enables exact adjustment of cutting
depth.
Ideal for cutting aluminium, plastic, fiberglass (max. 4
mm) and metal sheets up to 1.6 mm.
Strokes
Weight
Diameter in mm
Length in mm
Air Consumption
Coupler Size
Hose Diameter
10000rpm
0.68Kgs
38
225
170 l/min
1/4”
9mm
4
PNEUMATIC TOOLS
Ratchet Screwdrivers
Art. No. 00703 839 0 - 3/8”
Art. No. 00703 811 0 - 1/2”
Precision planetary gear.
Greater transmission of force and longer service life.
Short form (1/4“ + 3/8“).
Ideally suited for use in hard-to-reach places.
Outlet air guided toward rear, away from working area.
No air outlet in the working area.
Speed can be set via integrated controller.
Optimum adjustment to application.
Right/left directional switch is in a recess.
Prevents inadvertent switching.
Swiveling compressed-air connection.
Eliminates twisting of connection hose.
Rubber coating of ratchet head.
Prevents dirt from penetrating into unit.
Model
Square Drive
Max. Torque
Operating Pressure
Weight in Kgs
Length in mm
Avg. Air Consumption
Conn, Thread
Min. Hose Size
DRS 3/8”
3/8”
41Nm
6.3
0.5
196
196
1/4”
9mm
DRS 1/2”
1/2”
68Nm
6.3
0.5
256
256
1/4”
9mm
Pneumatic Drills
Art. No. 00703 796 0 - DBM10 - RL (A.) - (2330)
Art. No. 00703 797 0 - DBM13 - RL (B.) - (2330)
Especially light and handy drills with quick-action drill
chuck. Right/left switchover on the RL models with 10
and 13-mm drill chuck.
Plastic handle.
A.
B.
Warm hands.
Light, compact design. Reduced vibrations.
Low-fatigue, pleasant working.
Integrated silencer.
Low noise level.
Model
Chuck Holder
Speed in rpm
Weight in Kgs
Dimension (l x w x h)
Connection Thread
Conn, Thread
Min. Hose Size
DBM10 - RL
3/8” -24 UNF
1700
1.0
180x170x50
R1/4”
1/4”
9mm
DBM13 - RL
1/2”-24 UNF
700
1.5
205x170x50
R1/4”
1/4”
9mm
5
PNEUMATIC TOOLS
DWS 115 Grinder
Art. No. 00703 855 0 (2331)
Powerful, handy machines for sanding, cutting and roughing work.
Plastic housing.
Warm hands.
Compact shape, reduced vibration.
Low-fatigue, pleasant working.
Spindle stop.
Quick disk changes.
Disc Ø
Weight in Kgs
Length
Operating Pressure
Power Output
Speed
Avg. Air Consumption
Conn, Thread
Min. Hose Size
115mm
1.6
255mm
6.3
600W
10000rpm
113
1/4”
9mm
Die Grinders
Art. No. 00703 230 0 - DSG 25 Straight (2332)
Art. No. 00703 231 014 - DSW 22 Angled (2332)
Long-life, handy rod grinders with tool free speed control
and rubber-coated han dle against vibrations and cold
hands.
Rubber-coated handle.
Warm hands.
Light, compact design.
Fatigue-free, low vibration operation.
Swiveling compressed-air connection.
No twisting of connection hose.
Model
Chuck
Speed
Operating Pressure
Dimensions (l x w x h)
Avg. Air Consumption
Conn, Thread
Min. Hose Size
DSG 25 Straight
6mm
25000rpm
6.3
158x35x60
113 l/min
1/4”
9mm
DSW 22 Angled
6mm
22000rpm
6.3
158x38x75
113 l/min
1/4”
9mm
6
PNEUMATIC TOOLS
DBS 3600
Art. No. 00703 360 1
Time-saving system for removal of under-body protection, sealing com pound, paint, rust and film. Particularly well suited for
cleaning of welding beads during repair work, paint and rust
removal for all bodywork areas, as well as removal of protective paint from repair panels. Patented worldwide.
No heating up of treated areas.
No smearing or loading of the tools.
Longer service life of the brushes.
Significantly faster work progress.
Very light and handy power tool.
Speed
Weight in Kgs
Length
Operating Pressure
Noise Level
Avg. Air Consumption
Conn, Thread
Min. Hose Size
3500rpm
1.4
305mm
6.3
83dB
113
1/4”
10mm
Coarse Brush Belts (2339)
Fine Brush Belts (2339)
Nylon Sanding Fleece Disc (1636)
Art. No. 00703 350 51– 11mm
Art. No. 00703 350 31– 11mm
Art. No. 00585 110 0 - 100x13mm
Art. No. 00703 350 1 - 23mm
Art. No. 00703 350 3 - 23mm
23mm Flange Adapter
Art. No. 00703 350 2
7
PNEUMATIC TOOLS
DTS 152 C Orbital Sander
Art. No. 00703 752 1
Art. No. 00586 600 013 - Backing Pads
Oil - free, powerful pneumatic motor.
No oil residues on the processed surface, effective working progress.
Continuous speed control with safety switch - off.
Optimum adaptation of the sanding insert and paper change without
decoupling the compressed air .
Large - sized bearings with dust guard.
Rugged and long - lasting .
Effective, rotating silencer.
Minimal noise emissions and jointed exhaust outlet for maximum operating comfort .
For external dust extraction.
Minimal dust buildup thanks to optimum extraction options with vacuum cleaners or stationary extraction systems.
Extremely compact housing design.
Ergonomic shape and perfect handling.
Sanding Plate Ø
Free speed
Operating Pressure in Bar
Weight
Sound Level
Air Consumption
Coupler Size
Hose Diameter
150mm
12000rpm
6.3
0.71Kgs
85dB
113 l/min
1/4”
9mm
Rodcraft Air Riveter
Art. No. 01703 670 0
Handy blind riveter with collection container for torn-off rivet pins.
Comes standard with 4 different size nose pieces
Will rivet up to 5mm rivets (aluminium/copper ONLY)
Weight in Kg
1.6
Length in mm
225
Height in mm
280
Operating Pressure in Bar
6.3
Setting Force
12000N @ 6.3Bar
Device Stroke
23mm
Air Consumption per rivet in L
1.2
Coupler Size
1/4”
Hose Connection in mm
6
8
PNEUMATIC TOOLS
Headless Pinner and Nailer
Art. No. 01703 11 22
Height
168mm
Length
222mm
Width
48mm
Weight
0.98Kgs
Capacity
100Pcs
Min/Max. Air Pressure
4.9-6.9 Bar
1/2” Crown Air Staple Gun 6-16mm
Art. No. 01703 112 16
Height
155.6mm
Length
230mm
Width
46mm
Weight
0.9Kgs
Capacity
160Pcs
Min/Max. Air Pressure
4.2-6.9 Bar
Art. No. 01480 120...
18G Air Brad Nailer (15-50mm)
Art. No. 01703 18 50
Height
250.9mm
Length
247.1mm
Width
60mm
Weight
1.33Kgs
Capacity
110Pcs
Min/Max. Air Pressure
4.9-7.6 Bar
Art. No. 01480 125...
18G Air Brad Nailer (10-35mm)
Art. No. 01703 18 35
Height
210mm
Length
260mm
Width
59mm
Capacity
100Pcs
Min/Max. Air Pressure
4-7 Bar
Art. No. 01480 125...
9
PNEUMATIC TOOLS
16G Air Brad Nailer (19-50mm)
Art. No. 01703 16 50
Height
248mm
Length
286mm
Width
70mm
Capacity
100Pcs
Min/Max. Air Pressure
4.9-7.6 Bar
Art. No. 01480 250...
Air Coil Nailer (45-90mm)
Art. No. 01703 25 90
Height
330mm
Length
300mm
Width
130mm
Capacity
150-300Pcs
Min/Max. Air Pressure
5-8 Bar
Tacker and Nail Driver (J19)
Art. No. 01703 11 500
PNEUMATIC ACCESSORIES
1/2” Filter, Regulator, Oiler
1/4” Filter, Regulator, Oiler
In-line Oil Mister
Pneumatic Tool Oil 1Ltr
Art. No. 00699 003 12
Art. No. 00699 003 14
Art. No. 00699 070 314
Art. No. 00893 050 5
10
PNEUMATIC ACCESSORIES
Female Thread Coupling
A Connection
SW in mm
L in mm
D in mm
Art. No.
1/4”
22
41
27
00699 101 4
3/8”
22
41
27
00699 103 8
1/2”
24
42.5
27
00699 101 2
Male Thread Coupling
A Connection
SW in mm
L in mm
D in mm
Art. No.
1/4”
22
40
27
00699 111 4
3/8”
22
41
27
00699 113 8
1/2”
24
41
27
00699 111 2
Hose Tail Couplings
A Connection
SW in mm
L in mm
D in mm
Art. No.
6mm
22
55
27
00699 126
9mm
22
55
27
00699 129
13mm
24
55
27
00699 121 3
Female Thread Nipple
A Connection
SW in mm
L in mm
Art. No.
1/4”
17
33
00699 201 4
3/8”
19
33
00699 203 8
1/2”
24
35
00699 201 2
Male Thread Nipple
A Connection
SW in mm
L in mm
Art. No.
1/4”
17
33
00699 211 4
3/8”
19
33
00699 213 8
1/2”
24
35
00699 211 2
Hose Tail Nipple
A Connection
L in mm
Art. No.
6mm
44
00699 36
9mm
44
00699 39
13mm
44
00699 313
Pliovic Air Hose
Int. Dia.
Int. Dia. In mm
Outer Dia.
Work. Pressure
Art. No.
1/4”
6.4
12.7
250 PSi
01699 906
3/8”
9.5
16.8
250 PSi
01699 909
1/2”
12.7
20.6
250 PSi
01699 901 3
11