Figure 5-39. Disassembly of cheek pad for rifles

Figure 5-39. Disassembly of cheek pad for rifles

STOCK
CHEEK PAD WITH
OR MID.
LACE
ASSEMBLY/
INSTALLED
@N
RIFIE,
MIC
DISASSEMBLE/ASSEMBLE
_,
DISASSEMBLE,‘ASSEMBlE
WOOD
SCPEN.
LACE.
.
\\ 5)
.-
-
REMOVE,‘INSTALL
CHEEK
-’
. __..
UKILL NO. 31 (0.
HOLES I IN. i?JEEP
DRILLING
HOLES
WOOD SCRE’NS.
IN
STOCK
ASSEMBLY
FOR
PAD.
j.
120),
ASSEMBLING
WE
Figure
5-39.
Disassembly
of cheek
pad for rifles
MIC
and MfD
10438
(Sniper’s).
41
LAUNCHER
BODY
WE 10417
Figure
Figure
42
6-41.
S-/O.
Disassembly/assembty
launcher M7A.5’.
Remove/install
grenade
of grenade
launcher
sight
Ml&
DRILL JIG
CLAMP SCREW
SIGHT
Figure
J
DRILL JIG
5-&L Drilling stock assembly
grenade launcher sight jig.
using
43
1
2
3
4
-
Figure
Screw 7310009
Plate 7311859
Screw 7310095
Bracket and Spring
5-43.. Grenade
5 - Screw 7310093
6 - Level Assembly
7 - Body 7310096
launcher
sight
Ml5
7310097
- exploded
view.
LEFT-HAND
BAYONET-
RIGHT-HAND
BAYONETWE 10419
Figure
5-44.
Disassembly/assembly
of bayonet-knife
ML
45
Figure
6-46.
D~_q~ssembly/assembly
of bayonzt-knife
M6Al.
CHECK FOR
CHECK FOR TOIlN
STITCHING
AND RIPS
I
CHECK FOR RUST
AND IF, SECURE
WORN
FINISH
CHECK FOR RUST
DEFORMATION
CRACKS
OR BROKiN
TIP
I
LACE
CHECK FOR TEARS
AND PLIABILITY
WE 12706
Figure
5-4.6.
Inspection
points
for scabbard-bayonet
knife
M&Jr.
CLIP END
MUST BE SECURE
WE 12647
Figure
5-47.
inspection
points
for sling
Ml.
47
i
WE 10426
Figure
48
6-48.
Trigger ho+&ng assembly
65e8g97
- exploded
view.
2
L
I
,,..tt
-
Figure
6-49.
Stock assembly
and gun hand guard group - exploded
.-All,
Iww
view.
49
50
WE 10428
&%gt&?r 6-61.
Bolt a888mbly
axplodsd Vi8W
66.46063 -
Figure
Figwc
6-63.
Rear
sight
6-66.
group r exploded
Latch
group - explpded
view.
view.
51
I
,
Figure
52
64.4. Gas qdinder
group - sxpzoded
view.
WE
Figwe
6-66.
Telescope
mount oasambly
for rifls MIC (Sniper’s)
- exploded
10527
view.
53
Figure
6-66.
TeZescope
noounting
Figure
bracket
6-67. Cheek
(Sniper’s)
assembly
for rijle
pad for rijles WC
- exploded
view.
MlD (Sniper’s)
and MID
1
- exploded
view.
Section II.
5-2.
GAGING
HEADSPACE
Gaging Hcadspoce
See figure
Section Ill.
5-35.
TIMING
RIFLE
5-3. Timing Rifle
See figure
5-36.
55
CHAPTER
6
FINAL INSPECTION
6-1. General
The rifles must meet the limits of serviceability as indicated
by the repair
standards in chapter 7. Gaging is limited
tc those dimensions that are critical or
that may be m&e advantageously measured than repaired.
6-2. Visual Inspection
Overall appearance
56
will be approx-
imately that of a new weapon. All exposed
metal surfaces are to have adull, rust resistant finish
with no burs or deep
scratches. Barrels must be straight, clean,
free of rust, powder fouling, bulges, cracks
and r i n gs. All applicable modifications
must be applied. The serialnumbersmust
be legible.
CHAPTER 7
REPAIR STANDARDS
General
7-l.
The repair standards included here in
give the minimumandmaxlmummeasure-
ments of repaired parts; those beyond the
limits will be replaced by new parts.
7-2. Specific
a Bolt Assembly.
Point o/
Measurement
Fig.
NO.
Firing pin protrusion
5-17.
Standard8
Repair
Mdnimum
Maximum
0.044 in.
0.060 in.
(overseas)
b. Gas CyIimier Group.
Point of
Measurement
Fig.
No.
Gas cylinder bore
S-23.
Standards
Nfzzimum
Rc$air
N.inimum
0.5320 in.
-
c. FoIIower Group.
Point of
Fig.
No.
5-14.
d
Repair Stundarde
MfZhlWm
Minimum
M.easvement
Operating rod gas
piston diameter
Trigger Housing Assembly.
Fig.
No.
Point of
-
Repair Standard8
Minimvn
MaZimUm
Neasurement
Trigger-trigger
5-5.
0.525 in.
Pull
5.5 lb
Ml
7.5 lb
MlC and MID
cwwrw
6.5 lb
4.5 lb
e. Barrel and Receiver
Fig.
No.
Group
POW of
Measurement
Repair Standards
Minimum
MoZimVn
5-31.
Throat of chamber
5-32.
Barrel gas port
0.306 in.
0.310 in.
(overseas) (bands of
troops)
0.5991 in.
outer
(overseas)
CHAPTER 8
OVERHAUL PROCEDURES
8-1. General
Overhaul procedures
are similar
to
those contained in ohapter 5. Repairparts
are listed in appendix II. For furtbr details on overhaul, oontaot Command Gen-
eral, Headquarters, U.S. Army Weapons
Command, Attnz AMSWJS-SAM-SA, Rook
Island Arsenal,
Rook bland, Illinois
61201.