Reference - Viglen

Side 2
7
Install DIMM
Memory
8
Bank 2
DIMM 2B Socket
DIMM 2A Socket
Bank 1
Intel Server Chassis SC5275-E Note: When installing your server board into the Intel Server Chassis SC5275-E, install the hard drive bay before making your connections.
See the Intel® Server Chassis SC5275-E Quick Start User's Guide for instructions on installing the drive bay.
®
Bank 3
DIMM 1B Socket
DIMM 1A Socket
Memory Type: Minimum of one
128MB, DDR266/333-compliant
registered SDRAM 184-pin DIMM.
DIMM 3B Socket
DIMM 3A Socket
Notes and Cautions:
A single DIMM can be used in the
first slot of Bank 1 (DIMM1A).
Bank 1 (DIMM1B and DIMM1A)
must be fully populated before
populating Bank 2 (DIMM2B and
DIMM2A). Memory in Bank 2
must be populated in pairs.
E.
D.
F.
L.
O.
A.
The DIMM size, speed and vendor
must be the same within a bank.
However, the DIMM size can vary
between banks. For example,
Bank 1 can use two 128-MB
DIMMs and Bank 2 can use two
256-MB DIMMs.
G.
N.
N.
N.
N.
C.
C.
3
Open both DIMM socket levers.
2
Note location of alignment notch.
3
4
4
ets
ock
MS
Insert DIMM making sure the
connector edge of the DIMM
aligns correctly with the slot.
Check that socket levers are
securely latched.
DIM
10
Before installing your operating system, you must finish your chassis installation, make I/O
connections and plug in AC power.
Intel Server Chassis SC5275-E Back Panel
®
2. See your chassis documentation to
complete rack or pedestal installation.
Serial B
PS2/Mouse
USB
1, 2, 3
SC5300 Base/BRP
CPU Fan 1
CPU Fan 2
... if CPU 2 is installed
Fan 1 Header
Fan 2 Header
Fan 3 Header
Fan 4 Header
Fan 5 Header
Fan 6 Header
SC5300 LX
N
Front
Fan 1
Fan 2
Fan 1
Fan 2
Fan 3
Fan 4
Note: USB 3 (top) is not present on the Intel® Server Board SE7520BD-V.
M
Rear
Look on the Server/System Management screen in the BIOS Setup Utility to determine the
installed BIOS and FRU/SDR versions. Compare these to the versions at:
http://support.intel.com/support/motherboards/server/SE7520BD2/
If new versions are available, update the BIOS and FRU/SDR on your server.
See the User Guide on the Intel® Server Deployment Toolkit CD for update instructions.
B. Configure your Server with the Server Configuration Wizard
Boot to the Server Board SE7520BD2 Intel® Server Deployment Toolkit CD.
Select the Server Configuration Wizard to configure your server for remote server
management. Unless you have downloaded a newer version of the FRU/SDR from
the Web, use the Server Configuration Wizard also to load the FRU/SDR.
C. Configure your RAID Controller
Use the instructions provided with the RAID controller.
D. Install your Operating System
Use the instructions provided with the RAID controller and with the operating system.
CPU 2
CPU 1
Socket
Socket
G
L
SC5300-Fixed Drives SC5300-HS Drives
SC5275-E
Serial ATA
K
H
Front USB
J
I
Your Intel Server Board SE7520BD2 has six diagnostic LEDs visible from
the chassis back panel. The following text describes the function of
each LED:
LED E - System Fault LED, can be OFF or Amber = ON.
LED F - System ID, can be OFF or Blue = ON.
Diag LEDs
Diag MSB
Diag LSB
Note: Not all optional connections are shown
in this diagram. Refer to the Reference section
of this Quick Start User's Guide, your Intel®
Server Board SE7520BD2 User Guide, and
your server chassis documentation for additional
connection information.
With the operating system running, insert the Intel® Server Deployment Toolkit CD.
If using a Microsoft* Windows* operating system, the Express Installer will autorun
and allow you to select the appropriate drivers to install. On other operating systems,
browse the CD folders to locate and install the driver files.
F. Install Intel® Management Module-Professional (optional)
or Intel® Management Module-Advanced Edition (optional)
G. Install Intel® Server Management 8 (optional)
With the operating system running, insert the Intel® Server Management 8 CD that
came with your server board. On a Windows* operating system, the Setup program
will auto-run. Follow the on-screen instructions. For installation details, see
Getting Started with Intel® Server Manager 8, located on the ISM CD.
H. Install Intel® SMaRT Tool (optional)
With the operating system running, insert the Intel® Server Deployment Toolkit CD.
The Express Installer will autorun. Click Intel® SMaRT Tool at the left side of the
screen. Follow the on-screen instructions. For information about Intel® SMaRT Tool,
see http://developer.intel.com/design/servers/smarttool/index.htm.
See the Connections and Reference sections
of this document for server board Serial B
header location.
Serial B
Front Panel
Location
E F
System
ID
System Fault
G
A
B C DE F
L
H
I
J
K
M
Server Board Component Layout
A:
B1:
B2:
C:
D:
E:
F1:
F2:
G:
H:
I:
J:
K:
L:
M:
N:
O:
P:
Q:
R:
S:
T:
U:
V:
Chassis Intrusion
Left side - PCI-X 100 Slot
Right side - PCI-X 100 Slot
Super I/O
PCI Slot 32/33
ATI* Rage XL Graphics Controller
Left side - x8 (x4 speed)
PCI-Express* Slot
Right side - x8 PCI-Express* Slot
Intel® 82541PI 10/100/1000
PCI-X 133 Slot
Battery
ICMB Connector
System Fan 5
System Fan 6
System I/O Connectors
Auxiliary Power Connector
Main Power Connector
CPU Power Connector
DIMM Sockets
CPU 1 Fan Header
CPU 1
CPU 2
IMM Connector
IDE Connector
W:
X:
Y:
Z:
AA:
BB:
CC:
DD:
EE:
FF:
GG:
HH:
II:
JJ:
KK:
LL:
MM:
NN:
OO:
PP:
QQ:
RR:
Floppy Connector
System Fan 4
System Fan 2
System Fan 1
HSBP A
Front Panel USB
Front Panel LCD
IPMB
SATA A2
Speaker
SATA A1
HSBP B
Front Panel Connector
SCSI Channel A
System Fan 3
OEM RMC
ICH5R
SCSI Channel B
CPU 2 Fan Header
MCH
PXH
Serial B
*Diagnostic LEDs are not available on the Intel® Server Board SE7520BD2-V.
E. Install Operating System Drivers
For the Intel® Server Chassis SC5300, a front
panel Serial B cable comes factory installed.
Reference
Back Panel Diagnostic LEDs*
Getting Started with Intel® Server Management and Intel® SMaRT Tool (optional)
A. Confirm BIOS and FRU/SDR Versions
3. Attach the other end to the Serial B
connector on the server board.
See Reference section below for the
connector location.
Serial B Back Panel Location
SCSI
Hot-swap Backplane Headers A-B
SCSI Connectors
Floppy Connector
Front USB Header
Serial B Header
SATA 1-2
Network
2. Install the Serial B cable by inserting it
into the chassis back panel cutout and
attaching the two hex screws as shown.
F
CPU Fan 2
A B C D
Video
1. Use a screwdriver to remove
the connector knockout.
12V
NIC1
[10/100/1000]
Software
I
D
E
CPU Fan 1
Fan 1
Fan 2
Screwdriver
Slot
E
SC5275-E
Intel® Server Board SE7520BD2 Back Panel
NIC2
[10/100/1000]
Keyboard
B
Chassis Back
Panel
D
O
Note: It is normal for the LEDs to flash during boot and occasionally during
proper system operation. Analysis of the bits is only necessary if the system
is hung, and the LEDs are continuously lit.
Serial A
For the Intel® Server Chassis SC5275-E and SC5300, you have the option of
connecting the Serial B cable to the back of the chassis.
Insert
from inside
of chassis
P
Diagnostic LEDs A, B, C, and D are multi-colored LEDs that can be OFF, Green,
Amber, or Red. Each color represents 4 bits in a 16-bit hexadecimal code.
All of the codes are documented in the Intel® Server Board SE7520BD2
Technical Product Specification.
AC
Power
3. Connect your keyboard,
mouse, video, and other
I/O cables as shown.
A
Main Power Connector
Auxiliary Signal Connector
+12V CPU Power Connector
Front Panel Connector
IDE Connector
Chassis Intrusion Header
11
Finishing Up
1. Replace the chassis cover.
SC5275-E
Note: All available server board connections are not shown. Your configuration may vary.
Avoid touching gold contacts
when handling or installing
DIMMs.
2
4. Connect the AC
power cable last.
SC5300 - all configurations
Optional Connections
for Selected Chassis
I.
M.
H.
J.
B.
K.
Install the Serial B Cable [optional]
C
CPU/System Fan Connections
for Selected Chassis
Note: Bank 3 cannot be populated with DDR333-compliant DIMMs.
1
®
Required Connections
for Selected Chassis
1
9
Making Connections to the Server Board ... Quick Reference
Common Problems and Solutions
For a list of hardware components that have been tested with this system,
see: http://support.intel.com/support/motherboards/server/SE7520BD2
The system does not boot or show video at power-on.
• Check that the +12V CPU power connector is plugged in. Without this cable,
the processors will not have any power.
• If configuring with only one processor verify that the processor is in the
Primary Processor socket (CPU 1).
• Remove and replace DIMMs one bank at a time to isolate which one is
causing problems.
• Remember, all DIMMs must be:
• Registered DDR266 or DDR333 compliant.
• The same speed.
• From the same manufacturer.
• Installed beginning with DIMM 1B.
• Installed with no empty sockets inbetween filled sockets.
• Spacing: DDR-333 in bank 2 only.
DDR-266 in bank 2 or 3.
• Mirroring: DDR-333 (bank 1 to 2).
• Single slot populate: DIMM 1A.
• Your power supply must provide a minimum of 600-W with 2-A standby
current, which complies with the SSI EPS 12V specification.
The system sometimes works, but is exhibiting erratic behavior.
• This is typically the result of using an under-rated power supply.
Make sure you are using at least a 600-W power supply.
N
RR
O
P
QQ
OO
PP
NN
R
MM
LL
KK
II
GG
CPU 2
CPU 1
JJ
HH
FF
DD BB Z X W
EE
AA
VU
CC
Y
T
S
Accessories and Order Codes
Intel® Server Board SE7520BD2
SE7520BD2
Intel® Server Chassis SC5300 Base
SC5300BASE
Intel® Server Chassis SC5300 BRP
SC5300BRP
Intel® Server Chassis SC5300 LX
SC5300LX
Intel® Server Chassis SC5275-E [Black]
SC5275E
Intel® Server Chassis SC5300 Rack Conversion Kit
ARIGRACK
Intel® Server Chassis SC5300 Hot-Swap SCSI 4-Drive Bay Upgrade Kit
AXX4SCSIDB
Intel® Server Chassis SC5300 Hot-Swap SCSI 6-Drive Bay Upgrade Kit
AXX6SCSIDB
Intel® Server Chassis SC5300 Hot-Swap SATA 6-Drive Bay Upgrade Kit
AXX6SATADB
Intel® RAID Controller SRCU42X
SRCU42X
Intel® RAID Controller SRCU42E
SRCU42E
Intel® RAID Controller SRCZCRX
SRCZCRX
Intel® RAID Controller SRCS16
SRCS16
Intel® Management Module-Professional
AXXIMMPRO
Intel® Management Module-Advanced Edition
AXXIMMADV
Intel® Local Control Panel
AXXLCPPED
A complete list of accessories and spares can be found at:
www.intel.com/go/serverbuilder
Q