Entec Engineered Resins Hylex® P13lOL Polycarbonate Page 1 of2

Entec Engineered Resins Hylex® P13lOL Polycarbonate Page 1 of2

Entec Engineered Resins Hylex® P13lOL Polycarbonate
Page 1 of2
E
Monday, 02 March 2009
Hylex® P131 OL
Unit System:
Entec Engineered Resins - Polycarbonate
Actions
English
Legend (ORen)
General Information
General
Material Status
•
Commercial: Active
Availability
•
North America
Additive
•
Mold Release
•
UV Stabilizer
Features
•
•
•
General Purpose
Good Flow
General Purpose
•
•
Good Mold Release
Good UV Resistance
•
FDA 21 CFR 177.1580
Uses
Agency Ratings
RoHS Compliance
•
RoHS Compliant
Appearance
•
Natural Color
Forms
•
•
Pellets
Injection Molding
Processing Method
A5TM and 150 Properties
Physical
1
Nominal Value
fu1ecific Gravity
Unit
Test Method
1.20
Melt Mass-Flow Rate (300°C/1.2 kg)
ASTM D792
10 g/10 min
Molding Shrinkage - Flow
0.0050 to 0.0070 in/in
Water Absoq:)lion (24 hr)
ASTM 0955
0.15 %
Nominal Value
Mechanical
Tensile Strength (73°F)
ASTM 0570
Unit
Test Method
10100 psi
Tensile Elongation (Break, 73°F)
ASTM 0638
120 %
Flexural Modulus (73°F)
340000 psi
Flexural Strength (73°F)
13500 psi
Impact
Nominal Value
Notched Izod Imgact (73°F, 0.125 in)
ASTM D638
ASTM 0790
ASTM 0790
Unit
Test Method
15.0 ft'lb/in
Hardness
Nominal Value
Rockwell Hardness (M-Scale)
Oeflection Temgerature Under Load (66 psi, Unannealed)
Deflection Temperature Under Load (264 psi, Unannealed)
Vicat Softening Temperature
Electrical
Volume Resistivit}!
Test Method
Nominal Value Unit
285 of
Test Method
ASTM 0785
ASTM D648
270 OF
ASTM 0648
310 OF
Nominal Value
4.0E+16
Dielectric Strength (0.125 in, in Air)
ASTM 01525
Unit
ohm-ern
410 Vlmil
120 sec
Flammability
Nominal Value
Flame Rating - UL (0.0200 in)
Nominal Value
Refractive Index
Test Method
ASTM 0257
ASTM 0149
ASTM 0495
Unit
Test Method
Unit
Test Method
V-2
Optical
ASTM 0256
Unit
80
Thermal
ASTM 01238
UL94
1.585
ASTM D542
TransmittaQcJ;1(125 mil)
89.0 to 91.0 %
ASTM D1003
Haze (125 mil)
0.50 to 0.80 %
ASTM D1003
Processing Information
Injection
Drying Temperature
Drying Time
Orying Time, Maximum
Suggested Max Moisture
http://catalog.ides.comldatasheet.aspx?I=6482&E=24943
Nominal Value Unit
250 OF
3.0 to 4.0 hr
12 hr
0.020 %
3/212009
Entec Engineered Resins Hylex® P1310L Polycarbonate
Page 2 of2
40 to 60 %
Suggested Shot Size
520 to 540 of
Rear Temperature
Middle Temperature
530 to 550 OF
Front Temperature
540 to 570 of
Nozzle Temperature
530 to 570 of
Processing (Melt) Temp
550 to 600 of
Mold Temperature
170 to 200 OF
Injection Pressure
1000 to 1800 psi
Holding Pressure
700 to 1200 psi
Back Pressure
70.0 to 150 psi
Screw Speed
40 to 70 rpm
Injection Notes
Pressures given are in the hydraulic circuit.
Drying time should not exceed 12 hours to avoid excessive heat history.
Drying time is 5 to 6 hours with regrind.
Dew point of circulating air to be less than -20°F at hopper inlet.
Air throughout minimum of 1 CFMllb resin/hr.
Notes
1 Typical properties: these are not to be construed as specifications.
~
PO',re "'d t.y Copyright © 2009 IDES - The Plastics Web®
~IDES
-
~
~
The information presented on this data sheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to
assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final
material selection, data points are validated with the material supplier.
http://catalog.ides
.COm! datasheet.aspx
?I=6482&E=2494
3
3/2/2009