NELES® R-SERIES SEGMENT VALVE Flanged RE and

NELES® R-SERIES SEGMENT VALVE
Flanged RE and Wafer RE1
Metso's Neles RE series control valves are
economical, high performance valves in a quarterturn design. They are offered with a variety of trim
options from standard and low Cv trims for general
applications to noise/cavitation Q-Trim™ for
reducing aerodynamic noise and preventing
cavitation.
Standard units are equipped with either diaphragm
or cylinder actuators and ND9000 intelligent valve
controllers for precise control, reliability and
performance monitoring on-line.
FEATURES
Integral body construction
□ Integrally flanged R-Series valves feature one piece
body construction with no flange rings, inserts or end
caps to create potential leak paths, even if the valve is
subjected to pipe bending forces. Seating capabilities
are totally unaffected by pipeline forces, which assures
reliable valve operation.
Accurate Control
Economical
□ Carefully designed V-ported segmented ball, low
torque requirements and backlash-free movement
results in exceptional control performance. This design
provides steady and gental contact between the seat
and segment at all times to minimize friction while at
the same time providing exceptional control characteristics. Bearings are located inside the valve body
providing larger bearing areas, lower bearing loads
and longer bearing life.
□ Low torque operation reduces wear, resulting in better
reliability. In addition, standard designs carry hard
chromium facing on the segment and a stellited seat,
which has been designed to avoid flow impingement.
Together with a low load bearing design and
liveloaded packing, operational life is improved and
maintenance needs are minimized. Low torque combined with a well integrated actuator design provides
a lower cost valve assembly.
Safety and Environmental
Low flow and noise attenuation/cavitation
Q-Trim options
□ Rotary operation reduces fugitive emissions dramatically compared to sliding stem designs. The R-series
stem seal design meets the US clean Air Act and German TA-Luft requirements.
Durable metal seat
Reliable actuators
□ Quadra-Powr® spring diaphragm operators provide
safe, reliable operation even with minimal supply pressures are available. B-Series piston actuators are available in either double acting or spring return versions.
3 R 25 US • 2/2013
□ The seat of the R-series V-port segment valve is firm
and uniquely durable. The seat is designed in such a
way that its sealing surface is not located directly in the
flow stream. This gives the seat an extended service
life. The working principle is a pressure-aided seat
which enables good sealing properties at a low pressure difference. The seat is located inside the valve,
which prevents forces from the pipe system influencing the sealing effect. Two-way tight seat is available as
an option.
□ 1" valves feature five different segment sizes. They
extend the valves’ application range to very low-flow
and high accuracy services, such as additive and coloring lines, pilot plants etc. Cavitation and aerodynamic
noise are reduced with the patented Q-Trim option.
This self-cleaning design handles contaminated flows
(impure steam, river water, etc.) without plugging.
3 R 25 US
METSO
EXPLODED VIEW
E SEAT
26 10 19 17
4 5 6
4
35 35
T SEAT
4A
RE150 - 700
RE025 - 100
5
16
33
1S SEAT
20
6
4
33
9
S SEAT
4 5 6
12 14 3 15
1
13
11
22
PARTS LIST
BODY MATERIAL
Part
Name
Stainless steel
Body
ASTM A351 gr. CF8M
ASTM A216 gr. WCB
3
V-port segment
SIS 2324 + chromium / SIS 2324 / AISI 329
SIS 2324 + chromium / SIS 2324 / AISI 329
4
Seat
Cobalt based alloy / PTFE 1)
Cobalt based alloy / PTFE 1)
Back ring
AISI 316
AISI 316
4A
5
Lock spring
INCONEL 625
INCONEL 625
6
Back seal
Stainless steel + PTFE
Stainless steel+ PTFE
9
Gland follower
ASTM A351 gr. CF8M
ASTM A351 gr. CF8M
10
Blind flange
ASTM A351 gr. CF8M
ASTM A351 gr. CF8M
11
Drive shaft
SIS 2324/AISI 329 duplex SS
SIS 2324/AISI 329 duplex SS
12
Shaft
SIS 2324/AISI 329 duplex SS
SIS 2324/AISI 329 duplex SS
13
Key
SIS 2324/AISI 329
SIS 2324/AISI 329
14
Cylindrical pin
SIS 2324/AISI 329
SIS 2324/AISI 329
15
Cylindrical pin
SIS 2324/AISI 329
SIS 2324/AISI 329
PTFE + SS net
16
Bearing
PTFE + SS net
17
Bearing
PTFE + SS net
PTFE + SS net
19
Sealing plate
Graphite
Graphite
20
Packing
PTFE/Graphite 1)
PTFE/Graphite 1)
22
Filling ring
(only low Cv 1"/DN 25)
Stainless Steel AISI 316
Stainless Steel AISI 316
24
Stud
ISO 3506 A4-80/B8M
ISO 3506 A4-80/B8M
25
Hexagon nut
ISO 3506 A4-80/B8M
ISO 3506 A4-80/B8M
26
Hexagon bolt
ISO 3506 A4-80/B8M
ISO 3506 A4-80/B8M
30
Retainer Plate
AISI 316
AISI 316
32
Spring stack
SIS 2324 & CrMo Steel + ENP
SIS 2324 & CrMo Steel + ENP
33
Back-up ring
PTFE
PTFE
35
Identification plate
AISI 304
AISI 304
1) Alternative materials
2
Carbon steel
1
TECHNICAL BULLETIN 2/13
30
24
32
25
3 R 25 US
NELES® R-SERIES SEGMENT VALVE Flanged RE and Wafer RE1
TECHNICAL SPECIFICATIONS
Type
Shut-off classification
Integrally flanged V-ported ball, quarter-turn valve
Pressure ratings are as follows:
Body: ASME 150 - 300, see page 5.
Trim: See tables on page 5.
ANSI/FCI 70.2 Class IV
- Standard with metal seats.
Tested with 50 psig water.
ANSI/FCI 70.2 Class V
- Standard with soft seats.
Tested with 100 psig water.
1/10th ANSI/FCI 70.2 Class IV (Not Available with Low Cv Trims)
- Optional with metal seats.
Tested with 50 psig air.
E-Seat is non-tight
Sizes
RE1; 1", 1 1/2", 2", 3", 4", 6", 8"
RE; 1", 1 1/2", 2", 3", 4", 6", 8", 10", 12", 14", 16", 20", 24", 28"
End Connections
Flow capacity
Wafer (RE1)
Flanged (RE)
See table on this page.
Valve trim rotation
Face-to-face dimensions
ASME/ISA S75.04, IEC 534-3-2. IEC 534-3-2. Optional B16.10 with
spool piece construction.
Clockwise to close.
OPTIONS
Q-trim:
Temperature range
Inch 2", 3", 4", 6",8", 10", 12", 14", 16", 20" ,
24" and 28"
-58...+500°F / -50°C ... +260°C
Reduced Cv trim: For 1" valve only.
Inherent flow characteristic
Standard V-port: Equal percentage.
Q-Trim: Modified equal percentage.
Fire safety
Fire safe design to meet API 607, 3rd edition (RE only).
Maximum Cv-coefficients for RE-series valves
Size
DN
Inch
Metal seat, S
Q-Trim
Metal seat, 1S
Q-Trim with 1S
Soft seat, T2
Cv 100 %1)
Cv 100 %2)
Cv 100 %1)
Cv 100 %2)
Cv 100 %1)
25
1
45
–
24
–
21
40
1 1/2
110
–
58
–
61
110
50
2
180
47
115
30
65
2 1/2
280
96
210
72
215
80
3
420
160
342
130
340
100
4
620
250
510
210
520
150
6
1260
540
1160
500
1070
200
8
2030
880
1910
830
1760
250
10
3210
1510
3050
1440
2830
300
12
4490
2140
4340
2070
4080
350
14
6440
3160
6220
3050
5750
400
16
8510
4180
8330
4090
7630
500
20
13020
6600
12560
6370
–
600
24
–
–
19700
9230
–
700
28
–
–
25300
13700
–
1) 100 % corresponds to 95° turning angle
2) For Q-R-valves, 100 % corresponds to 90° turning angle
TECHNICAL BULLETIN 2/13
3
3 R 25 US
METSO
SEAT DESIGNS
S Metal seat
T Soft seat
S Metal seat
Seat:
316 SS + Cobalt based hard facing
Spring:
Inconel 625
Seat seal:
Filled PTFE lipseal / SS Elgiloy spring
Temp. Range:
--50 °C... +260 °C / - 58 °F …+500 °F
Service:
General
T Soft seat
Flow direction
Flow direction
E Non-tight metal seat
Seat:
316 SS with PTFE + X-treme®, sizes 1" - 6"
316 SS with PTFE + C25 % insert, sizes 8" - 28"
Spring:
Inconel 625
Seat seal:
Filled PTFE lipseal
Back seal:
PTFE
Temp. Range:
-50 °C... +260 °C / - 58 °F …+500 °F
Service:
General service with tight shut-off.
1S 2-way tight metal seat
E Non-tight metal seat
Seat:
Cobalt based alloy
Temp. Range:
-50 °C... +260 °C / - 58 °F …+500 °F
Service:
Extremely erosive applications, non-tight.
NOTE !
Flow direction is reversed.
1S 2-way metal seat
Flow direction
Flow direction
Seat:
316 SS + Cobalt based hard facing
Spring:
Inconel 625
Seat seal:
Viton GF
Temp. range:
-30 °C... +200 °C / - 22 °F …+186 °F
Service:
General
CONSTRUCTION OPTIONS
Low Cv trims
Reduced Cv trims are available on the 1"
valve to control very low flows with high
accuracy. The narrow orifice is a selfflushing
design because the trim orifice is continually
increasing.
Q-trim valve trim for cavitation/noise abatement
Liquid cavitation and aerodynamic noise
problems can be solved with the patented
Q-Trim valve trim. This design employs the
two well-known principles of dividing the
pressure drop into a series of small pressure
drops and of separating the flow stream into
many small jet streams. The use of these two
principles combined with the rotation of the attenuator elements
provides a combination of cavitation/noise abatement with high
rangeability, high capacity and the capability to handle impure
fluids.
4
TECHNICAL BULLETIN 2/13
Erosion resistant version
This heavy duty erosion resistant
design handles contaminated
flows and abrasive media at a favorable cost/useable life ratio. The
seat is machined from cobalt chromium alloy and the seat design is
changed from normal to reverse
flow for maximum abrasion resistance. This version should not be
used for isolation service since the
seat is not in contact with the segment.
3 R 25 US
NELES® R-SERIES SEGMENT VALVE Flanged RE and Wafer RE1
BODY PRESSURE RATINGS
Maximum operating pressure
differential in shut-off service
Maximum operating pressure
differential in control service
Note:
Note:
1) RE-valves are not recommended for applications with high onoff cycling rate. X- or L-series valves should be used in these
cases.
Given maximum allowable throttling differential pressures are
based on mechanical strength of the parts only. Nelprof® analysis
determines actual throttling dp capability, taking into account
trim velocity, exit velocity, noise and cavitation.
2) Please observe body rating for material in question when
determining maximum allowable shut-off pressure differential.
TECHNICAL BULLETIN 2/13
5
3 R 25 US
METSO
SELECTION OF STANDARD ACTUATORS, QUADRA POWR
SPRING
RATE
psi
MAX
SHUT-OFF DP
psi
RE, Q-RE
MAX
CONTROL DP
psi
RE
MAX
CONTROL DP
psi
Q-RE
ND Intelligent Valve
NP Pneumatic
Controller
Positioner
Recommmended model Recommmended model
VALVE SIZE
inch
ACTUATOR
SIZE
1
QP1C
60
727
509
507
ND 9103
NP 729
1 1/2
QP1C
60
727
509
507
ND 9103
NP 729
2
QP1C
60
727
509
507
ND 9103
NP 729
3
QP1C
60
320
320
319
ND 9103
NP 729
3
QP2B
41
509
509
507
ND 9103
NP 729
3
QP2C
60
727
509
507
ND 9103
NP 729
3
QP2D
80
727
509
507
ND 9103
NP 729
4
QP2C
60
509
364
261
ND 9103
NP 729
4
QP2D
80
582
364
261
ND 9103
NP 729
4
QP3B
41
582
364
261
ND 9103
NP 724
4
QP3C
60
582
364
261
ND 9103
NP 724
6
QP3B
41
320
320
261
ND 9103
NP 724
6
QP3C
60
407
364
261
ND 9103
NP 724
6
QP3D
80
582
364
261
ND 9103
NP 724
6
QP4B
41
582
364
261
ND 9106
NP 724
6
QP4C
60
582
364
261
ND 9106
NP 724
8
QP3C
60
233
233
217
ND 9103
NP 724
8
QP4B
41
407
364
217
ND 9106
NP 724
8
QP4C
60
509
364
217
ND 9106
NP 724
8
QP4D
80
509
364
217
ND 9106
NP 724
10
QP4C
60
291
291
145
ND 9106
NP 724
10
QP4D
80
407
291
145
ND 9106
NP 724
NP 726
10
QP5B
41
465
291
145
ND 9106
10
QP5C
60
509
291
145
ND 9106
NP 726
12
QP5B
41
218
145
116
ND 9106
NP 726
12
QP5C
60
364
145
116
ND 9106
NP 726
12
QP5D
80
436
145
116
ND 9106
NP 726
14
QP5C
60
174
145
116
ND 9106
NP 726
14
QP5D
80
247
145
116
ND 9106
NP 726
16
QP5C
60
116
116
116
ND 9106
NP 726
16
QP5D
80
189
145
116
ND 9106
NP 726
NOTES
1)
Maximum shut-off differential pressures for valves are given considering clean media. Safety margins between 10 % - 25 %
are typically recommended for cases where media is sticky or has tendency to built-up inside the valve.
2)
Selection is based on supply pressures as per relevant spring rate.
3)
Maximum shut-off differential pressures are given at ambient temperature, see curves on page 5.
4)
Maximum control differential pressures must not be based on values in this table only. Nelprof calculation, taking into account
noise level, inlet/outlet velocity, existence of cavitation, and actuator load factors must be observed when determing valves' differential pressure capability.
6
TECHNICAL BULLETIN 2/13
3 R 25 US
NELES® R-SERIES SEGMENT VALVE Flanged RE and Wafer RE1
DIMENSIONS
Series RE1
Dimensions, inch
Type
lbs.
NPS
A
A1
C
D
K
S
T
U
L
H
E
R
O
M
P
N
RE1_01
01
4.02
2.01
2.20
1.30
4.02
2.76
-
M10
0.61
3.15
8.15
4.13
0.59
0.19
0.67
0.98
8.8
RE1_1H
1H
4.49
2.24
2.56
1.93
4.27
2.76
-
M10
0.61
3.15
8.41
4.13
0.59
0.19
0.67
0.98
12.1
17.6
RE1_02
02
4.88
2.44
3.58
2.36
4.70
2.76
-
M10
0.61
3.15
8.84
4.13
0.59
0.19
0.67
0.98
RE1_03
03
6.50
3.25
4.25
3.50
5.59
3.54
-
M12
0.63
3.54
10.51
4.92
0.79
0.19
0.87
1.38
30.9
RE1_04
04
7.64
3.82
4.72
4.53
5.94
3.54
-
M12
0.63
3.54
10.87
4.92
0.79
0.19
0.87
1.38
39.7
RE1_06
06
9.02
4.51
6.85
6.46
7.87
4.33
1.26
M12
0.87
3.54
13.19
5.31
0.98
0.25
1.09
1.81
83.8
RE1_08
08
9.57
4.39
7.91
8.07
9.25
5.12
1.26
M12
0.87
4.33
15.55
6.30
1.18
0.25
1.30
2.01
143.3
TECHNICAL BULLETIN 2/13
7
3 R 25 US
METSO
Series RE
DN 600...700
DN150...500
DN25...100
S
S
S
U
M
T
T
M
M
S2
C
øB
øD
DN
K
(L)
E
H
R
N
RE_A DN25...700
(KEY)
P
øO
A1
A
Valve is shown in closed position
8
Dimensions. inch
Size
Inch
A1
A
C
øD
K
S
T
U
L
H
1"
1 1/2"
2"
2 1/2"
3"
4"
6"
8"
10"
12"
14"
16"
20"
24"
28"
2.01
2.24
2.44
2.85
3.25
3.82
4.51
4.39
5.45
6.06
6.89
6.3
7.17
13.98
11.61
4.02
4.49
4.88
5.71
6.5
7.64
9.02
9.57
11.69
13.31
15.75
15.75
17.99
24.02
27.95
2.2
2.56
3.58
3.82
4.25
4.72
6.85
7.91
9.88
10.59
12.24
13.9
16.54
19.29
21.22
1.29/ 1.49*
1.93
2.36
2.95
3.5
4.45
6.46
8.07
10.2
11.81
13.78
15.75
19.69
23.62
27.56
4.02
4.27
4.7
4.96
5.59
5.94
7.87
9.25
10.91
12.8
14.41
16.26
18.43
27.72
30.24
2.76
2.76
2.76
2.76
3.54
3.54
4.33
5.12
5.12
6.3
6.3
6.3
9.06
13/12
13/12
1.26
1.26
1.26
1.57
1.57
2.17
3.54
4.72
4.72
M10
M10
M10
M10
M12
M12
M12
M12
M12
M16
M16
M20
M27
M30
M30
0.61
0.61
0.61
0.59
0.63
0.63
0.87
0.87
1.02
1.02
1.14
1.14
1.57
1.57
2.17
3.15
3.15
3.15
3.15
3.54
3.54
3.54
4.33
4.33
4.72
4.72
5.51
7.09
8.66
8.66
E
8.15
8.41
8.84
9.09
10.51
10.87
13.19
15.55
17.52
19.04
22.2
22.99
28.62
32.99
35.98
Dimensions, mm
Size
DN/inch
A1
A
C
øD
K
S/S2
T
U
L
H
25/1"
40/1 1/2"
50/2"
65/2 1/2"
80/3"
100/4"
150/6"
200/8"
250/10"
300/12"
350/14"
400/16"
500/20"
600/24''
700/28''
51
57
62
72.5
82.5
97
114.5
111.5
138.5
154
175
160
233
355
295
102
114
124
145
165
194
229
243
297
338
400
400
508
610
710
56
65
91
97
108
120
174
201
251
269
311
353
420
490
539
33
49
60
75
89
113
164
205
259
300
350
400
500
600
700
182
188.5
199.5
205
232
241
290
345
387
445
486
553
618
704
768
70
70
70
70
90
90
110
130
130
160
160
160
230
330/304.7
330/304.7
32
32
32
40
40
55
90
120
120
M10
M10
M10
M10
M12
M12
M12
M12
M12
M16
M16
M20
M27
M30
M30
15.5
15.5
15.5
15.5
16
16
22
22
26
26
29
29
40
40
55
80
80
80
80
90
90
90
110
110
120
120
140
150
220
220
TECHNICAL BULLETIN 2/13
E
207
213.5
224.5
230
267
276
335
395
445
513
566
643
768
838
914
Shaft dimensions, inch
RE_A (Key)
R
øO
M
P
4.13
0.59 0.19 0.67
4.13
0.59 0.19 0.67
4.13
0.59 0.19 0.67
4.13
0.59 0.19 0.67
4.92
0.79 0.19 0.87
4.92
0.79 0.19 0.87
5.31
0.98 0.25 1.09
6.3
1.18 0.25 1.3
6.61
1.38 0.38 1.54
7.4
1.57 0.38 1.74
7.87
1.77
0.5 1.98
9.06
1.97
0.5 2.19
11.5
2.76 0.75 3.08
13.94 2.95 0.75 3.22
14.41 3.35 0.88 3.75
Shaft dimensions, mm
RE_A (Key)
R
øO
M
P
105
15
4.76
17
105
15
4.76
17
105
15
4.76
17
105
15
4.76
17
125
20
4.76
22.2
125
20
4.76
22.2
135
25
6.35
27.8
160
30
6.35
32.9
168
35
9.53
39.1
188
40
9.53
44.2
200
45
12.7
50.4
230
50
12.7
55.5
292
70
19.05 78.2
354
75
19.05 81.9
366
85
22.23 95.3
N
0.98
0.98
0.98
0.98
1.38
1.38
1.81
2.01
2.28
2.68
3.15
3.54
4.69
5.28
5.75
N
25
25
25
25
35
35
46
51
58
68
80
90
119
134
146
Flange dims & weights
ASME 150
ASME 300
øB
lbs
øB
lbs
4.25
8
4.88
11
5
10
6.1
17
5.98
16
6.5
21
7.09
29
7.48
36
7.52
31
8.27
42
9.02
46
10
64
10.98
86
12.52 119
13.5
136
15
183
15.98 200 17.72 306
19.02 312 20.47 438
21.02 447 22.99 625
23.5
581 25.51 781
27.52 946
34.25 1155 38.25 1597
36.50 1731 40.75 2303
Flange dims & weights
ASME 150
ASME 300
øB
Kg
øB
Kg
108
3.6
124
4.9
127
4.6
155
7.5
152
7.4
165
9.5
185
13
185
13
191
14
210
19
229
21
254
29
279
39
318
54
343
62
381
83
406
91
450
139
483
142
520
199
534
203
584
284
597
264
648
355
699
430
869.9 525
971.5
726
927.1 787 1035.1 1047
3 R 25 US
NELES® R-SERIES SEGMENT VALVE Flanged RE and Wafer RE1
NPS
RE1-QPX
Dimensions, inch
Valve size Inch
Actuator size QPX
lbs.
A
A1
E
F
G
H
Imax
J
K
X
1"
1
4.02
2.01
5.59
15.04
12.99
15.28
8.07
8.86
7.17
8.39
33
1.5"
1
4.49
2.24
5.59
15.04
12.99
15.91
8.07
9.13
7.44
8.39
36
2"
1
4.88
2.44
5.59
15.04
12.99
17.36
8.07
9.57
7.87
8.39
42
3"
2
6.5
3.25
6.14
18.9
15.31
20.08
8.46
10.83
9.13
8.98
73
4"
2
7.64
3.82
6.14
18.9
15.31
20.87
8.46
11.54
9.49
8.98
82
6"
2
9.02
4.51
6.14
18.9
15.31
24.8
8.46
13.46
11.42
8.98
126
6"
3
9.02
4.51
7.48
22.24
17.56
25.98
8.66
13.62
11.42
10.79
157
8"
3
9.57
5.18
7.48
22.24
17.56
29.13
8.66
15.75
13.58
10.79
216
8"
4
9.57
5.18
8.98
25
19.49
30.31
8.86
16.14
13.58
12.6
260
K
X
RE1-QPX
Dimensions, mm
Valve size DN/Inch
Actuator size QPX
kgs
A
A1
E
F
G
H
Imax
J
25/1"
1
102
51
142
382
330
388
205
225
182
213
15
40/1.5"
1
114
57
142
382
330
404
205
232
189
213
17
50/2"
1
124
62
142
382
330
441
205
243
200
213
19
80/3"
2
165
83
156
480
389
510
215
275
232
228
33
37
100/4"
2
194
97
156
480
389
530
215
293
241
228
150/6"
2
229
115
156
480
389
630
215
342
290
228
57
3
229
115
190
565
446
660
220
346
290
274
71
200/8"
3
243
132
190
565
446
740
220
400
345
274
98
4
243
132
228
635
495
770
225
410
345
320
118
TECHNICAL BULLETIN 2/13
9
3 R 25 US
METSO
NPS
RE-QPX
Valve size
Inch
1"
1 1/2"
2"
3"
4"
6"
8"
10"
12"
14"
16"
Actuator size QP
1
1
1
1
2
2
3
3
4
4
5
5
5
5
A
4.02
4.49
4.88
6.5
7.64
9.02
9.02
9.57
9.57
11.69
11.69
13.31
15.75
15.75
E
5.59
5.59
5.59
5.59
6.14
6.14
7.48
7.48
8.98
8.98
10.87
10.87
10.87
10.87
A
102
114
124
165
194
229
229
243
243
297
297
338
400
400
E
142
142
142
142
156
156
190
190
228
228
276
276
276
276
F
15.04
15.04
15.04
15.04
18.9
18.9
22.24
22.24
25
25
30.24
30.24
30.24
30.24
Dimensions, inch
G
H
I
12.99
15.28
6.3
12.99
15.91
6.3
12.99
17.36
6.3
12.99
19.29
6.77
15.31
20.75
6.77
15.31
24.8
7.52
17.56
25.87
8.43
17.56
29.09
7.52
19.49
30.24
8.43
19.49
33.86
8.43
23.94
35.67
9.57
23.94
38.66
8.43
23.94
41.93
9.57
23.94
46.22
9.57
J
8.86
9.13
9.57
10.83
11.54
13.46
13.62
15.79
16.02
17.68
18.27
20.55
22.17
24.8
K
7.17
7.44
7.87
9.13
9.49
11.42
11.42
13.58
13.58
15.24
15.24
17.52
19.13
21.77
X
8.39
8.39
8.39
8.39
8.98
8.98
10.79
10.79
12.6
12.6
15.04
15.04
15.04
15.04
Pipe d
9.06
9.65
10.43
12.99
13.78
17.72
16.14
20.47
19.09
22.44
21.26
25.59
28.94
34.25
Weight lbs
ASME 150
Weight lbs
ASME 300
42
44
48
64
99
139
172
222
266
330
451
563
697
832
45
51
55
75
117
172
205
268
312
436
557
689
876
1034
Weight kgs
ASME 150
Weight kgs
ASME 300
19
20
22
29
45
63
78
101
121
150
205
256
317
378
21
23
25
34
53
78
93
122
142
198
253
313
398
470
RE-QPX
Valve size
DN/Inch
25/1"
40/1.5"
50/2"
80/3"
100/4"
150/6"
200/8"
250/10"
300/12"
350/14"
400/16"
10
Actuator QPX
1
1
1
1
2
2
3
3
4
4
5
5
5
5
TECHNICAL BULLETIN 2/13
F
382
382
382
382
480
480
565
565
635
635
768
768
768
768
G
330
330
330
330
389
389
446
446
495
495
608
608
608
608
Dimensions, mm
H
I
388
160
404
160
441
160
490
172
527
172
630
191
657
214
739
191
768
214
860
214
906
243
982
214
1065
243
1174
243
J
225
232
243
275
293
342
346
401
407
449
464
522
563
630
K
182
189
200
232
241
290
290
345
345
387
387
445
486
553
X
213
213
213
213
228
228
274
274
320
320
382
382
382
382
Pipe d
230
245
265
330
350
450
410
520
485
570
540
650
735
870
3 R 25 US
NELES® R-SERIES SEGMENT VALVE Flanged RE and Wafer RE1
MOUNTING POSITION A (STANDARD)
NPT
X
øD
G
F
NPT
A1
SUPPLY G 1/4
A
SIGNAL M20 X 1.5
NPS
V
øB (only RE)
C
I
J
H
FLOW DIRECTION
RE1-B1C
Type
RE1_01-B1C6
RE1_1H-B1C6
RE1_02-B1C6
RE1_02-B1C9
RE1_03-B1C6
RE1_03-B1C9
RE1_04-B1C6
RE1_04-B1C9
RE1_06-B1C9
RE1_06-B1C11
RE1_06-B1C13
RE1_08-B1C9
RE1_08-B1C11
RE1_08-B1C13
Max. Δp
(psi) *1
363
363
363
363
363
363
363
363
363
363
363
218
363
363
NPS
1
1H
2
2
3
3
4
4
6
6
6
8
8
8
A
4.02
4.49
4.88
4.88
6.5
6.5
7.64
7.64
9.02
9.02
9.02
9.57
9.57
9.57
A1
2.01
2.24
2.44
2.44
3.25
3.25
3.82
3.82
4.51
4.51
4.51
4.78
5.18
5.18
C
2.2
2.56
3.58
3.58
4.25
4.25
4.72
4.72
6.85
6.85
6.85
7.91
7.91
7.91
D
1.3
1.93
2.36
2.36
3.5
3.5
4.53
4.53
6.46
6.46
6.46
8.07
8.07
8.07
Dimensions, inch
F
G
15.75
10.24
15.75
10.24
15.75
10.24
17.91
12.4
15.75
10.24
17.91
12.4
15.75
10.24
17.91
12.4
17.91
12.4
21.26
14.76
25
17.52
17.91
12.4
21.26
14.76
25
17.52
X
3.54
3.54
3.54
4.33
3.54
4.33
3.54
4.33
4.33
5.31
6.89
4.33
5.31
6.89
V
1.42
1.42
1.42
1.69
1.42
1.69
1.42
1.69
1.69
2.01
2.56
1.69
2.01
2.56
J
6.61
6.89
7.28
7.28
7.87
7.87
8.27
8.27
10.24
10.43
11.02
11.57
12.2
12.8
H
12.01
12.6
13.98
14.37
15.35
15.75
16.14
16.54
20.28
20.87
21.65
22.64
23.23
24.02
Imax
12.2
12.2
12.2
12
12.2
12
12.2
12
12
12.2
12.8
12
12.2
12.8
NPT
lbs.
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
3/8
3/8
1/4
3/8
3/8
18
21
27
52
40
52
49
61
110
121
154
165
17
210
RE-B1C
Type
RE_01-B1C6
RE_1H-B1C6
RE_02-B1C6
RE_2H-B1C6
RE_03-B1C6
RE_04-B1C6
RE_06-B1C6
RE_06-B1C9
RE_06-B1C11
RE_08-B1C6
RE_08-B1C9
RE_08-B1C11
RE_10-B1C9
RE_10-B1C11
RE_10-B1C13
RE_10-B1C17
RE_12-B1C11
RE_12-B1C13
RE_12-B1C17
RE_14-B1C13
RE_14-B1C17
RE_14-B1C20
RE_16-B1C17
RE_16-B1C20
RE_16-B1C25
RE_20-B1C25
RE_24-B1C25
RE_24-B1C32
RE_28-B1C32
RE_28-B1C40
Max. Δp
(psi) *1
727
727
727
727
727
582
145
364
582
58
218
465
102
218
422
509
102
276
436
131
305
393
218
305
436
233
9
19
10
23
NPS
1
1 1/2
2
2 1/2
3
4
6
A
4.02
4.49
4.88
5.71
6.5
7.64
9.02
C
2.2
2.56
3.58
3.82
4.25
4.72
6.85
ØD
1.29/1.49*2
1.9
2.4
3.0
3.5
4.4
6.5
8
9.57
7.91
8.07
10
11.69
9.88
10.2
12
13.31 10.59
11.81
14
15.75 12.24
13.78
16
15.75
13.9
15.75
20
24
20
24
16.93
19.6
19.69
23.6
28
28
21.5
27.6
Dimensions, inch
F
G
X
15.75 10.24 3.54
15.75 10.24 3.54
15.75 10.24 3.54
15.75 10.24 3.54
15.75 10.24 3.54
15.75 10.24 3.54
15.75 10.24 3.54
17.91 12.4 4.33
21.26 14.76 5.31
15.75 10.24 3.54
17.91 12.4 4.33
21.26 14.76 5.31
17.91 12.4 4.33
21.26 14.76 5.31
25 17.52 6.89
30.31 21.46 8.46
21.26 14.76 5.31
25 17.52 6.89
30.31 21.46 8.46
25 17.52 6.89
30.31 21.46 8.46
33.07 22.64 8.46
30.31 21.46 8.46
33.07 22.64 8.46
42.3 28.5 10.43
42.3 28.5 10.43
42.3 28.5 10.4
53.9 36.2 15.6
53.9 36.2 15.6
65.7 45.3 19.9
V
1.42
1.42
1.42
1.42
1.42
1.42
1.42
1.69
2.56
1.42
1.69
2.01
1.69
2.01
2.56
3.07
2.01
2.56
3.07
2.56
3.07
3.82
3.07
3.82
4.76
4.76
4.8
6
6
7.6
J
9.45
9.72
10.16
10.43
11.42
11.77
13.7
13.74
13.98
15.87
15.91
16.14
17.56
17.8
18.43
19.02
19.0
19.6
20.2
20.2
20.8
21.6
23.2
24.0
24.9
28.5
33.1
34.6
37.2
39.1
H
13.43
14.06
15.51
16.14
17.44
18.27
22.32
22.76
23.5
25.55
25.98
26.73
29.61
30.35
31.77
33.15
32.2
33.7
35.0
35.9
37.3
38.1
41.4
42.2
44.0
50.5
59.0
61.9
66.4
69.1
I max
12.2
12.2
12.2
12.2
12.2
12.2
12.2
12.01
12.2
12.2
12.01
12.2
12.2
12.2
12.8
13.39
12.2
12.8
13.39
12.8
13.39
13.98
13.39
13.98
15.35
15.35
15.4
16.9
16.9
17.7
NPT
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
3/8
1/4
1/4
3/8
1/4
3/8
3/8
1/2
3/8
3/8
1/2
3/8
1/2
1/2
1/2
1/2
1/2
1/2
1/2
3/4
3/4
3/4
REC_ ASME 150
øB
lbs
4.25
26
5
30
5.98
35
7.28
40
7.52
46
9.02
62
10.98
102
114
130
13.5
152
165
180
15.98
229
251
306
356
19.02
356
389
440
21.02
524
574
616
23.5
711
752
880
27.52
1236
32.1
2420
2695
36.4
3313
3731
RED_ ASME 300
øB
lbs
4.88
26
6.1
31
6.5
37
8.27
57
10
75
12.52
113
125
141
15
198
211
227
17.72
334
350
383
433
20.47
482
515
565
22.99
702
752
794
25.51
911
953
1080
30.5
1285
36.0
2856
3131
40.7
3894
4312
*1: Max dp in on-off service with actuator load factor of 0.6 and supply pressure of 60psi (5bar)
*2: 1.49" (38mm) for low capacity segment eg C005-RE_
TECHNICAL BULLETIN 2/13
11
3 R 25 US
METSO
RE1-B1C
Dimensions, mm
Max. Δp
(bar) *1
Type
NPT
NPS
A
A1
C
D
F
G
X
V
J
H
kgs
Imax
RE1_01-B1C6
25
1
102
51
56
33
400
260
90
36
168
305
310
1/4
8
RE1_1H-B1C6
25
1H
114
57
65
49
400
260
90
36
175
320
310
1/4
10
RE1_02-B1C6
25
2
124
62
91
60
400
260
90
36
185
355
310
1/4
12
RE1_02-B1C9
25
2
124
62
91
60
455
315
110
43
185
365
305
1/4
24
RE1_03-B1C6
25
3
165
83
108
89
400
260
90
36
200
390
310
1/4
18
RE1_03-B1C9
25
3
165
83
108
89
455
315
110
43
200
400
305
1/4
24
RE1_04-B1C6
25
4
194
97
120
115
400
260
90
36
210
410
310
1/4
22
RE1_04-B1C9
25
4
194
97
120
115
455
315
110
43
210
420
305
1/4
28
RE1_06-B1C9
25
6
229
115
174
164
455
315
110
43
260
515
305
1/4
50
RE1_06-B1C11
25
6
229
115
174
164
540
375
135
51
265
530
310
3/8
55
RE1_06-B1C13
25
6
229
115
174
164
635
445
175
65
280
550
325
3/8
70
RE1_08-B1C9
15
8
243
121
201
205
455
315
110
43
294
575
305
1/4
75
RE1_08-B1C11
25
8
243
132
201
205
540
375
135
51
310
590
310
3/8
80
RE1_08-B1C13
25
8
243
132
201
205
635
445
175
65
325
610
325
3/8
95
RE-B1C
Dimensions, mm
REC_ ASME 150
NPS
A
C
ØD
F
G
X
V
J
H
I max
NPT
øB
kgs
øB
RE_ 01-B1C6
727
1
102
56
33/38*2
400
260
90
36
240
341
310
1/4
108
12
124
12
RE_ 1H-B1C6
727
1 1/2
114
65
49
400
260
90
36
247
357
310
1/4
127
14
155
14
17
kgs
RE_ 02-B1C6
727
2
124
91
60
400
260
90
36
258
394
310
1/4
152
16
165
RE_2H-B1C6
727
2 1/2
145
97
75
400
260
90
36
265
410
310
1/4
185
18
-
-
RE_ 03-B1C6
727
3
165 108
89
400
260
90
36
290
443
310
1/4
191
21
210
26
RE_04-B1C6
582
4
194 120
113
400
260
90
36
299
464
310
1/4
229
28
254
34
RE_06-B1C6
145
6
229 174
164
400
260
90
36
348
567
310
1/4
279
46
318
RE_06-B1C9
364
455
315
110
43
349
578
305
1/4
RE_06-B1C11
582
540
375
135
65
355
597
310
3/8
RE_08-B1C6
58
400
260
90
36
403
649
310
1/4
8
243 201
205
52
59
343
69
51
57
64
381
90
RE_08-B1C9
218
455
315
110
43
404
660
305
1/4
75
96
RE_08-B1C11
465
540
375
135
51
410
679
310
3/8
82
103
RE_10-B1C9
102
RE_10-B1C11
218
10
297 251
259
455
315
110
43
446
752
310
1/4
540
375
135
51
452
771
310
3/8
406
104
450
114
152
159
RE_10-B1C13
422
635
445
175
65
468
807
325
3/8
139
174
RE_10-B1C17
509
770
545
215
78
483
842
340
1/2
162
197
RE_12-B1C11
102
RE_12-B1C13
276
RE_12-B1C17
436
RE_14-B1C13
131
12
14
338 269
400 311
300
350
540
375
135
51
482
819
310
3/8
635
445
175
65
498
855
325
3/8
770
545
215
78
513
890
340
1/2
635
445
175
65
514
913
325
3/8
483
162
520
177
200
534
238
219
234
257
584
319
RE_14-B1C17
305
770
545
215
78
529
947
340
1/2
261
342
RE_14-B1C20
393
840
575
215
97
548
967
355
1/2
280
361
RE_16-B1C17
218
RE_16-B1C20
305
16
400 353
400
RE_16-B1C25
436
RE_20-B1C25
233
20
508 430
500
RE_24-B1C25
9
24
610 497
600
RE_24-B1C32
19
RE_28-B1C32
10
RE_28-B1C40
23
28
710 547
700
770
545
215
78
590 1051
340
1/2
840
575
215
97
609 1071
355
1/2
TECHNICAL BULLETIN 2/13
597
1075
725
265 121 632 1118
390
1/2
725
265 121 723 1283
390
1/2
700
815
1075
725
265 121 842 1498
390
1/2
1370
920
395 153 879 1573
430
3/4
1370
920
395 153 944 1686
430
3/4
1670 1150 505 194 993 1756
450
3/4
323
648
342
1075
*1: Max dp in on-off service with actuator load factor of 0.6 and supply pressure of 60psi (5bar)
*2: 1.49" (38mm) for low capacity segment eg C005-RE_
12
RED_ ASME 300
Max. Δp
(bar) *1
Type
400
491
562
775
1100
915
1225
925
1506
1696
414
433
584
1298
1423
1035
1770
1960
3 R 25 US
NELES® R-SERIES SEGMENT VALVE Flanged RE and Wafer RE1
MOUNTING POSITION A (STANDARD)
NPT
X
øD
G
F
NPT
A1
SUPPLY G 1/4
A
SIGNAL M20 X 1.5
NPS
V
øB (only RE)
C
I
J
H
FLOW DIRECTION
RE1-B1J
Type
Dimensions, inch
Max. Δp
(psi) *1
NPT
NPS
A
A1
C
D
F
G
X
V
J
H
lbs
Imax
RE11_01-B1J8/B1JA8
725/725
1
4.02
2.01
2.2
1.3
22.05
16.54
5.31
1.69
9.45
14.33
12.01
3/8
46
RE1_1H-B1J8/B1JA8
725/725
1H
4.49
2.24
2.56
1.93
22.05
16.54
5.31
1.69
9.72
14.96
12.01
3/8
51
RE1_02-B1J8/B1JA8
725/725
2
4.88
2.44
3.58
2.36
22.05
16.54
5.31
1.69
10.16
16.38
12.01
3/8
55
RE1_03-B1J8/B1JA8
725/725
3
6.5
3.25
4.25
3.5
22.05
16.54
5.31
1.69
11.42
18.35
12.01
3/8
66
RE1_04-B1J8/B1JA8
725/725
4
7.64
3.82
4.72
4.45
22.05
16.54
5.31
1.69
11.77
19.17
12.01
3/8
77
RE1_06-B1J8/B1JA8
145/363
6
9.02
4.51
6.85
6.46
22.05
16.54
5.31
1.69
13.7
23.23
12.01
3/8
121
RE1_06-B1J10/B1JA10
580/580
6
9.02
4.51
6.85
6.46
25.59
19.29
6.89
2.01
13.98
24.29
8.86
3/8
154
RE1_08-B1J8/B1JA8
-/174
8
9.57
4.78
7.91
8.07
22.05
16.54
5.31
1.69
15.91
26.5
12.01
3/8
176
RE1_08-B1J10/B1JA10
218/363
8
9.57
5.18
7.91
8.07
25.59
19.29
6.89
2.01
16.14
27.56
12.2
3/8
210
RE1_08-B1J12/B1JA12
464/508
8
9.57
5.18
7.91
8.07
31.5
24.41
8.46
2.56
16.77
28.98
9.25
1/2
265
RE-B1J
Dimensions, inch
Max. Δp
(psi) *1
NPS
A
C
RE_ 01-B1J8/B1JA8
727/727
1
4.02
2.20
RE_ 1H-B1J8/B1JA8
727/727
1 1/2
4.49
2.56
Type
REC_ (150#)
RED_ (300#)
NPT
øD
F
G
1.29/1.49*2 22.05 16.54
1.93
22.05 16.54
X
V
J
H
I max
5.31 1.69 9.45
14.33
12.01
5.31 1.69 9.72
14.96
12.01
øB
lbs
øB
3/8
4.25
55
4.88
lbs
55
3/8
5.00
59
6.10
62
66
RE_ 02-B1J8/B1JA8
727/727
2
4.88
3.58
2.36
22.05 16.54
5.31 1.69 10.16 16.38
12.01
3/8
5.98
64
6.50
RE_2H-B1J8/B1JA8
727/727
2 1/2
5.71
3.82
2.95
22.05 16.54
5.31 1.69 10.43 16.93
12.01
1/4
7.28
66
-
-
RE_ 03-B1J8/B1JA8
727/727
3
6.50
4.25
3.50
22.05 16.54
5.31 1.69 11.42 18.35
12.01
3/8
7.52
75
8.27
86
103
RE_04-B1J8/B1JA8
727/727
4
7.64
4.72
4.45
22.05 16.54
5.31 1.69 11.77 19.17
12.01
3/8
9.02
92
10.00
RE_06-B1J8/B1JA8
145/363
6
9.02
6.85
6.46
22.05 16.54
5.31 1.69 13.70 23.23
12.01
3/8
10.98
130
12.52
RE_06-B1J10/B1JA10
580/580
25.59 19.29
6.89 2.01 13.98 24.29
8.86
3/8
22.05 16.54
5.31 1.69 15.91 26.50
12.01
3/8
25.59 19.29
6.89 2.01 16.14 27.56
12.20
3/8
RE_08-B1J8/B1JA8
-/174
RE_08-B1J10/B1JA10
218/363
RE_08-B1J12/B1JA12
464/508
RE_10-B1J10/B1JA10
73/218
8
10
9.57
11.69
7.91
9.88
8.07
10.20
31.50 24.41
8.46 2.56 16.77 28.98
9.25
1/2
25.59 19.29
6.89 2.01 17.80 31.10
12.20
3/8
158
13.50
180
15.00
209
273
227
255
271
15.98
143
169
317
17.72
378
RE_10-B1J12/B1JA12
290/363
31.50 24.41
8.46 2.56 18.43 32.56
12.80
1/2
319
440
RE_10-B1J16/B1JA16
508/508
38.98 29.92 10.43 3.07 19.02 34.13
13.39
1/2
480
557
31.50 24.41
8.46 2.56 19.61 34.45
12.80
1/2
38.98 29.92 10.43 3.07 20.20 36.06
13.39
1/2
RE_12-B1J12/B1JA12
116/261
RE_12-B1J16/B1JA16
290/363
RE_12-B1J20/B1JA20
435/435
RE_14-B1J16/B1JA16
160/319
RE_14-B1J20/B1JA20
435/435
RE_16-B1J20/B1JA20
276/363
RE_16-B1J25/B1JA25
435/435
RE_20-B1J25/B1JA25
363/363
12
13.31 10.59
11.81
47.24 36.81 15.55 3.82 21.02 39.37
10.63
3/4
14
15.75 12.24
13.78
38.98 29.92 10.43 3.07 20.83 38.31
13.39
1/2
47.24 36.81 15.55 3.82 21.57 41.61
13.98
3/4
16
15.75 13.90
15.75
47.24 36.81 15.55 3.82 23.98 45.71
13.98
3/4
60.24 47.24 19.88 4.76 24.88 48.74
15.35
3/4
20
20.00 16.93
19.69
60.24 47.24 19.88 4.76 28.46 55.35
15.35
1/2
19.02
447
20.47
541
706
21.02
675
23.50
977
27.52
1584
572
667
832
22.99
854
25.51
1177
30.51
1382
840
1019
1364
1564
RE_24-B1J32/B1JA32
261/261
24
24.02 19.57
23.62
74.21 56.50 21.26 6.02 34.61 62.09
16.81
1
32.09
3608
36.02
4044
RE_28-B1JV32/B1JVA32
189/189
28
27.95 21.54
27.56
74.21 56.50 21.26 6.02 37.13 66.57
16.81
1
36.42
4226
40.75
4807
*1: Max Δp in on-off service with actuator load factor of 0.6 and supply pressure of 60psi (5bar)
*2: 1.49" (38mm) for low capacity segment eg C005-RE_
TECHNICAL BULLETIN 2/13
13
3 R 25 US
METSO
RE1-B1J
Dimensions, mm
Max. Δp
(bar) *1
Type
NPT
NPS
A
A1
C
D
F
G
X
V
J
H
kgs
Imax
RE11_01-B1J8/B1JA8
50/50
1
102
51
56
33
560
420
135
43
240
364
305
3/8
21
RE1_1H-B1J8/B1JA8
50/50
1H
114
57
65
49
560
420
135
43
247
380
305
3/8
23
RE1_02-B1J8/B1JA8
50/50
2
124
62
91
60
560
420
135
43
258
416
305
3/8
25
RE1_03-B1J8/B1JA8
50/50
3
165
83
108
89
560
420
135
43
290
466
305
3/8
30
RE1_04-B1J8/B1JA8
50/50
4
194
97
120
113
560
420
135
43
299
487
305
3/8
35
RE1_06-B1J8/B1JA8
10/25
6
229
115
174
164
560
420
135
43
348
590
305
3/8
55
RE1_06-B1J10/B1JA10
40/40
6
229
115
174
164
650
490
175
51
355
617
225
3/8
70
RE1_08-B1J8/B1JA8
-/12
8
243
121
201
205
560
420
135
43
404
673
305
3/8
80
RE1_08-B1J10/B1JA10
15/25
8
243
132
201
205
650
490
175
51
410
700
310
3/8
95
RE1_08-B1J12/B1JA12
32/35
8
243
132
201
205
800
620
215
65
426
736
235
1/2
120
RE-B1J
Dimensions, mm
Max. Δp
(bar) *1
NPS
DN
RE_ 01-B1J8/B1JA8
50/50
1
25
RE_1H-B1J8/B1JA8
50/50
1,5
RE_02-B1J8/B1JA8
50/50
2
RE_2H-B1J8/B1JA8
50/50
RE_03-B1J8/B1JA8
Type
A
C
G
NPT
øD
F
X
J
H
Imax
102 56
33/38*2
560
420 135 43 240 364
305
40
114 65
49
560
420 135 43 247 380
50
124 91
60
560
420 135 43 258 416
2,5
65
145 97
75
560
50/50
3
80
165 108
89
REC_ ASME 150
RED_ ASME 300
øB
kg
øB
kg
3/8
108
25
124
25
305
3/8
127
27
155
28
305
3/8
152
29
165
30
420 135 43 265 430
305
3/8
185
30
-
-
560
420 135 43 290 466
305
3/8
191
34
210
39
47
RE_04-B1J8/B1JA8
50/50
4
100 194 120
113
560
420 135 43 299 487
305
3/8
229
42
254
RE_06-B1J8/B1JA8
10/25
6
150 229 174
164
560
420 135 43 348 590
305
3/8
279
59
318
RE_06-B1J10/B1JA10
40/40
650
490 175 51 355 617
225
3/8
RE_08-B1J8/B1JA8
-/12
RE_08-B1J10/B1JA10
15/25
RE_08-B1J12/B1JA12
32/35
RE_10-B1J10/B1JA10
5/15
8
10
200 243 201
250 297 251
205
259
560
420 135 43 404 673
305
3/8
650
490 175 51 410 700
310
3/8
800
620 215 65 426 736
235
1/2
650
490 175 51 452 790
310
3/8
72
343
82
381
95
124
103
116
123
406
65
77
144
450
172
RE_10-B1J12/B1JA12
20/25
800
620 215 65 468 827
325
1/2
145
200
RE_10-B1J16/B1JA16
35/35
990
760 265 78 483 867
340
1/2
218
253
RE_12-B1J12/B1JA12
8/18
RE_12-B1J16/B1JA16
20/25
RE_12-B1J20/B1JA20
30/30
RE_14-B1J16/B1JA16
11/22
RE_14-B1J20/B1JA20
30/30
RE_16-B1J20/B1JA20
19/25
RE_16-B1J25/B1JA25
30/30
RE_20-B1J25/B1JA25
25/25
12
300 338 269
300
800
620 215 65 498 875
325
1/2
990
760 265 78 513 916
340
1/2
1200 935 395 97 534 1000
270
3/4
14
350 400 311
350
990
340
1/2
1200 935 395 97 548 1057
355
3/4
16
400 400 353
400
1200 935 395 97 609 1161
355
3/4
1530 1200 505 121 632 1238
390
3/4
20
500 508 430
500
1530 1200 505 121 723 1406
390
1/2
760 265 78 529 973
483
203
520
246
321
534
307
597
444
699
720
260
303
378
584
388
648
535
775
628
382
463
620
711
RE_24-B1J32/B1JA32
18/18
24
600 610 497
600
1885 1435 540 153 879 1577
427
1
815
1640
915
1838
RE_28-B1JV32/B1JVA32
13/13
28
700 710 547
700
1885 1435 540 153 943 1691
427
1
925
1921
1035
2185
*1: Max Δp in on-off service with actuator load factor of 0.6 and supply pressure of 60psi (5bar)
*2: 1.49" (38mm) for low capacity segment eg C005-RE_
14
V
TECHNICAL BULLETIN 2/13
3 R 25 US
NELES® R-SERIES SEGMENT VALVE Flanged RE and Wafer RE1
HOW TO ORDER
Example:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
-
RE1
D
A
03
D
J
J
S
T
1. Sign
Trim codes
---
standard V-port (no sign)
Q-
Low noise and anti-cavitation trim (for 2" and larger)
C005-
7. Sign
Maximum Cv = 1.5 (for 1" only)
C05-
Maximum Cv = 5.0 (for 1" only)
C15-
Maximum Cv = 15.0 (for 1" only)
Type AISI 329+HCr; ANSI 316+HCr for low Cv segments
S
Type AISI 329 ( without chrome ). Used with soft seats, eg.
RECA_CSJT2T
8. Sign
J
2. Sign
RE1
RE13
RE
9. Sign
Seat design and materials
Flanged body, face-to-face acc. to ASME B16.10 ( spool piece constr.)
(Available in sizes 1" - 12")
S
Stainless Steel+Cobalt Hard facing,
Inconel 625 spring, Filled PTFE/Elgiloy lipseal,
-40 °F …+480 °F ANSI/FCI 70-2 class IV, General services
Flanged body, face-to-face acc. to ISA S75.04 and DIN/IEC Part 3-2.
(Available in sizes 1" - 28")
T2
Stainless Steel with PTFE+C25% insert
E
Cobalt based alloy, -40 °F …+480 °F
Non-tight, extremely erosive services.
1S
316 SS + Cobalt based hard facing, 2-way metal seat
Pressure rating (Note: See table 1 on page 3)
C
ASME 150
D
ASME 300 For RE1D use sign "D" for both 150# and 300# valves.
A
Shaft, pin & bearing materials
Type AISI 329 Drive Shaft & PTFE on SS 316 net
Product series
Flangeless body, face-to-face acc. to ISA S75.04 and
DIN/IEC 534 Part 3-2. (Available in sizes 1" - 8")
3. Sign
4. Sign
-
Segment materials
J
Maximum Cv = 0.5 (for 1" only)
C015-
11.
/
10. Sign
Stem packing & blind flange seal
T
PTFE V-rings, live-loaded
G
Graphite rings, live loaded (fire-safe)
Construction (Note: See table 2 on page 3)
Standard, drive shaft with ANSI keyway to actuator
11. Sign
/-
5. Sign
Flange facing
ASME B16.5 Smooth finish (Ra 3.2 – 6.3 / RMS 125-250) (no sign)
Size
Inch 1", 1 1/2", 2", 2 1/2", 3", 4", 6", 8",
Flanged patter only; 10", 12", 14", 16", 20", 24", 28"
6. Sign
Body, blind flange & screw materials
A
ASTM A351 gr. CF8M (standard for sizes 12" and larger as well as 300#
Class Flanged models)
D
ASTM A216 gr. WCB / 1-0619 (blind flange & gland bolting A4-80,
corresponds to B8M)
C
ASTM A351 gr. CG8M (blind flange & gland bolting A4-80, corresponds
to B8M)
Note:- Gland material is always CF8M
TECHNICAL BULLETIN 2/13
15
Subject to change without prior notice.
Metso Automation Inc.
Europe, Vanha Porvoontie 229, P.O. Box 304, FI-01301 VANTAA, Finland.
Tel. +358 20 483 150. Fax +358 20 483 151
North America, 44 Bowditch Drive, P.O. Box 8044, Shrewsbury, MA 01545, USA.
Tel. +1 508 852 0200. Fax +1 508 852 8172
South America, Av. Independéncia, 2500- Iporanga, 18087-101, Sorocaba-São Paulo, Brazil.
Tel. +55 15 2102 9700. Fax +55 15 2102 9748/49
Asia Pacific, 20 Kallang Avenue, Lobby B, #06-00, PICO Creative Centre, Singapore 339411, Singapore.
Tel. +65 6511 1011. Fax +65 6250 0830
China, 19/F, the Exchange Beijing, No. 118, Jianguo Lu Yi, Chaoyang Dist, 100022 Beijing, China.
Tel. +86-10-6566-6600. Fax +86-10-6566-2575
Middle East, Roundabout 8, Unit AB-07, P.O. Box 17175, Jebel Ali Freezone, Dubai,
United Arab Emirates. Tel. +971 4 883 6974. Fax +971 4 883 6836
www.metso.com/valves