dent and buckle chart

DENT AND BUCKLE
CHART
Document N°: DBC-CO-002
Revision N° and Date: Rev.00 Apr 04, 11
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
CL415 - DBC
DENT & BUCKLE CHART
DBC-CO-002
Rev.00 Apr 04, 11
Reg. Marks: I-DPCO
1 Filling & Handling instructions
The “Dent & Buckle Chart” allows to know the presence and the location of external structural damages not involving flight safety and, for this purpose, it is
enclosed and maintained in ATLB (Aircraft Technical Log Book) retainer. For permanent repair management refer to NOTE 1.
Any time an external structural damage not involving flight safety is found in the airplane, Certifying Staff must fill up the form reporting all related information
(dimensions, SRM/HSMM references, engineering communication, etc.) following the below instructions:
1. On the left side :
• Item n° : Damage progressive number
• Date : Record date of the finding
• Description and Dimension : Short description and dimensions of the damage
• Inspector Signature : This signature certifies the identification of the damage
2. On the right side :
• A (Acceptable) : Report the AMM/SRM reference for acceptable damage
• T (Temporary) : Report the document issued for handling the deferred action
• Date : Record date of the corrective action. In particular:
- For Acceptable (A) records, report date of acceptable damage record
- For Temporary (T) records, report date of corrective action accomplishment.
• Inspector Signature : Certifying Staff signature
3. Identify the damage location and corresponding progressive number with an arrow and related number
NOTE 1 : Permanent Repair are not present in the D&BC because reported on the “Structure Repair File”.
NOTE 2 : At any Annual-Check, the DBC is cleaned up from all damaged permanent repaired, and a new form must be compiled by the Contracted Approved
Part 145 Maintenance Organisation (AMO) that perform the check. Original DBC must be removed from the airplane and sent to Inaer CAMO
Engineering Department
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
Page 2 of 10
DBC-CO-002
Rev.00 Apr 04, 11
CL415 - DBC
DENT & BUCKLE CHART
DBC-CO-002
Rev.00 Apr 04, 11
Reg. Marks: I-DPCO
Fuselage LH side
Fuselage upper side
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
Page 3 of 10
DBC-CO-002
Rev.00 Apr 04, 11
CL415 - DBC
DENT & BUCKLE CHART
Rev.00 Apr 04, 11
Reg. Marks: I-DPCO
Fuselage Bottom side
Fuselage RH side
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
DBC-CO-002
Page 4 of 10
DBC-CO-002
Rev.00 Apr 04, 11
DBC-CO-002
CL415 - DBC
DENT & BUCKLE CHART
Wing LH upper side
Reg. Marks: I-DPCO
Wing RH upper side
Wing RH Bottom side
Wing LH Bottom side
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
Rev.00 Apr 04, 11
Page 5 of 10
DBC-CO-002
Rev.00 Apr 04, 11
CL415 - DBC
DENT & BUCKLE CHART
Empennage RH side
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
DBC-CO-002
Rev.00 Apr 04, 11
Reg. Marks: I-DPCO
Empennage LH side
Page 6 of 10
DBC-CO-002
Rev.00 Apr 04, 11
CL415 - DBC
DENT & BUCKLE CHART
Empennage Upper side
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
DBC-CO-002
Rev.00 Apr 04, 11
Reg. Marks: I-DPCO
Empennage Bottom side
Page 7 of 10
DBC-CO-002
Rev.00 Apr 04, 11
CL415 - DBC
DENT & BUCKLE CHART
RH Propeller
DBC-CO-002
Rev.00 Apr 04, 11
Reg. Marks: I-DPCO
LH Propeller
L
BLADES FILLING INSTRUCTIONS
Underline numbering defect on above assembly to indicate
which blade is damaged and report same number on the
detailed drawing on the left on specific position.
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
Page 8 of 10
DBC-CO-002
Rev.00 Apr 04, 11
CL415 - DBC
DENT & BUCKLE CHART
Rev.00 Apr 04, 11
Reg. Marks: I-DPCO
Windows RH View
Windows LH View
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
DBC-CO-002
Page 9 of 10
DBC-CO-002
Rev.00 Apr 04, 11
CL415 - DBC
DENT & BUCKLE CHART
Item
n°
Description & Dimension
Date
Inspector
Signature
Acceptable, Temporary action
and/or Repair
DBC-CO-002
Rev.00 Apr 04, 11
Reg. Marks: I-DPCO
Date
Inspector
Signature
A
T
A
T
A
T
A
T
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
Page 10 of 10
DBC-CO-002
Rev.00 Apr 04, 11
DENT AND BUCKLE
CHART
Document N°: DBC-CQ-002
Revision N° and Date: Rev.00 May 18, 11
INAER Form ENG 007 Rev 00 - DBC dent & buckle chart 415
CL415 - DBC
DENT & BUCKLE CHART
DBC-CQ-002
Rev.00 Apr 14, 11
Reg. Marks: I-DPCQ
1 Filling & Handling instructions
The “Dent & Buckle Chart” allows to know the presence and the location of external structural damages not involving flight safety and, for this purpose, it is
enclosed and maintained in ATLB (Aircraft Technical Log Book) retainer. For permanent repair management refer to NOTE 1.
Any time an external structural damage not involving flight safety is found in the airplane, Certifying Staff must fill up the form reporting all related information
(dimensions, SRM/HSMM references, engineering communication, etc.) following the below instructions:
1. On the left side :
• Item n° : Damage progressive number
• Date : Record date of the finding
• Description and Dimension : Short description and dimensions of the damage
• Inspector Signature : This signature certifies the identification of the damage
2. On the right side :
• A (Acceptable) : Report the AMM/SRM reference for acceptable damage
• T (Temporary) : Report the document issued for handling the deferred action
• Date : Record date of the corrective action. In particular:
- For Acceptable (A) records, report date of acceptable damage record
- For Temporary (T) records, report date of corrective action accomplishment.
• Inspector Signature : Certifying Staff signature
3. Identify the damage location and corresponding progressive number with an arrow and related number
NOTE 1 : Permanent Repair are not present in the D&BC because reported on the “Structure Repair File”.
NOTE 2 : At any Annual-Check, the DBC is cleaned up from all damaged permanent repaired, and a new form must be compiled by the Contracted Approved
Part 145 Maintenance Organisation (AMO) that perform the check. Original DBC must be removed from the airplane and sent to Inaer CAMO
Engineering Department
INAER Form ENG 007 Rev 00 - DBC dent & buckle chart 415
Page 2 of 10
DBC-CQ-002
Rev.00 Apr 14, 11
CL415 - DBC
DENT & BUCKLE CHART
DBC-CQ-002
Rev.00 Apr 14, 11
Reg. Marks: I-DPCQ
Fuselage LH side
Fuselage upper side
INAER Form ENG 007 Rev 00 - DBC dent & buckle chart 415
Page 3 of 10
DBC-CQ-002
Rev.00 Apr 14, 11
CL415 - DBC
DENT & BUCKLE CHART
Rev.00 Apr 14, 11
Reg. Marks: I-DPCQ
Fuselage Bottom side
Fuselage RH side
INAER Form ENG 007 Rev 00 - DBC dent & buckle chart 415
DBC-CQ-002
Page 4 of 10
DBC-CQ-002
Rev.00 Apr 14, 11
DBC-CQ-002
CL415 - DBC
DENT & BUCKLE CHART
Wing LH upper side
Reg. Marks: I-DPCQ
Wing RH upper side
Wing RH Bottom side
Wing LH Bottom side
INAER Form ENG 007 Rev 00 - DBC dent & buckle chart 415
Rev.00 Apr 14, 11
Page 5 of 10
DBC-CQ-002
Rev.00 Apr 14, 11
CL415 - DBC
DENT & BUCKLE CHART
Empennage RH side
INAER Form ENG 007 Rev 00 - DBC dent & buckle chart 415
DBC-CQ-002
Rev.00 Apr 14, 11
Reg. Marks: I-DPCQ
Empennage LH side
Page 6 of 10
DBC-CQ-002
Rev.00 Apr 14, 11
CL415 - DBC
DENT & BUCKLE CHART
Empennage Upper side
INAER Form ENG 007 Rev 00 - DBC dent & buckle chart 415
DBC-CQ-002
Rev.00 Apr 14, 11
Reg. Marks: I-DPCQ
Empennage Bottom side
Page 7 of 10
DBC-CQ-002
Rev.00 Apr 14, 11
CL415 - DBC
DENT & BUCKLE CHART
RH Propeller
DBC-CQ-002
Rev.00 Apr 14, 11
Reg. Marks: I-DPCQ
LH Propeller
L
BLADES FILLING INSTRUCTIONS
Underline numbering defect on above assembly to indicate
which blade is damaged and report same number on the
detailed drawing on the left on specific position.
INAER Form ENG 007 Rev 00 - DBC dent & buckle chart 415
Page 8 of 10
DBC-CQ-002
Rev.00 Apr 14, 11
CL415 - DBC
DENT & BUCKLE CHART
Rev.00 Apr 14, 11
Reg. Marks: I-DPCQ
Windows RH View
Windows LH View
INAER Form ENG 007 Rev 00 - DBC dent & buckle chart 415
DBC-CQ-002
Page 9 of 10
DBC-CQ-002
Rev.00 Apr 14, 11
CL415 - DBC
DENT & BUCKLE CHART
Item
n°
Description & Dimension
Date
Inspector
Signature
Acceptable, Temporary action
and/or Repair
DBC-CQ-002
Rev.00 Apr 14, 11
Reg. Marks: I-DPCQ
Date
Inspector
Signature
A
T
A
T
A
T
A
T
INAER Form ENG 007 Rev 00 - DBC dent & buckle chart 415
Page 10 of 10
DBC-CQ-002
Rev.00 Apr 14, 11
DENT AND BUCKLE
CHART
Document N°: DBC-CR-002
Revision N° and Date: Rev.00 Jun 03, 11
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
CL415 - DBC
DENT & BUCKLE CHART
DBC-CR-002
Rev.00 Jun 03, 11
Reg. Marks: I-DPCR
1 Filling & Handling instructions
The “Dent & Buckle Chart” allows to know the presence and the location of external structural damages not involving flight safety and, for this purpose, it is
enclosed and maintained in ATLB (Aircraft Technical Log Book) retainer. For permanent repair management refer to NOTE 1.
Any time an external structural damage not involving flight safety is found in the airplane, Certifying Staff must fill up the form reporting all related information
(dimensions, SRM/HSMM references, engineering communication, etc.) following the below instructions:
1. On the left side :
• Item n° : Damage progressive number
• Date : Record date of the finding
• Description and Dimension : Short description and dimensions of the damage
• Inspector Signature : This signature certifies the identification of the damage
2. On the right side :
• A (Acceptable) : Report the AMM/SRM reference for acceptable damage
• T (Temporary) : Report the document issued for handling the deferred action
• Date : Record date of the corrective action. In particular:
- For Acceptable (A) records, report date of acceptable damage record
- For Temporary (T) records, report date of corrective action accomplishment.
• Inspector Signature : Certifying Staff signature
3. Identify the damage location and corresponding progressive number with an arrow and related number
NOTE 1 : Permanent Repair are not present in the D&BC because reported on the “Structure Repair File”.
NOTE 2 : At any Annual-Check, the DBC is cleaned up from all damaged permanent repaired, and a new form must be compiled by the Contracted Approved
Part 145 Maintenance Organisation (AMO) that perform the check. Original DBC must be removed from the airplane and sent to Inaer CAMO
Engineering Department
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
Page 2 of 10
DBC-CR-002
Rev.00 Jun 03, 11
CL415 - DBC
DENT & BUCKLE CHART
DBC-CR-002
Rev.00 Jun 03, 11
Reg. Marks: I-DPCR
Fuselage LH side
Fuselage upper side
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
Page 3 of 10
DBC-CR-002
Rev.00 Jun 03, 11
CL415 - DBC
DENT & BUCKLE CHART
Rev.00 Jun 03, 11
Reg. Marks: I-DPCR
Fuselage Bottom side
Fuselage RH side
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
DBC-CR-002
Page 4 of 10
DBC-CR-002
Rev.00 Jun 03, 11
DBC-CR-002
CL415 - DBC
DENT & BUCKLE CHART
Wing LH upper side
Reg. Marks: I-DPCR
Wing RH upper side
Wing RH Bottom side
Wing LH Bottom side
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
Rev.00 Jun 03, 11
Page 5 of 10
DBC-CR-002
Rev.00 Jun 03, 11
CL415 - DBC
DENT & BUCKLE CHART
Empennage RH side
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
DBC-CR-002
Rev.00 Jun 03, 11
Reg. Marks: I-DPCR
Empennage LH side
Page 6 of 10
DBC-CR-002
Rev.00 Jun 03, 11
CL415 - DBC
DENT & BUCKLE CHART
Empennage Upper side
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
DBC-CR-002
Rev.00 Jun 03, 11
Reg. Marks: I-DPCR
Empennage Bottom side
Page 7 of 10
DBC-CR-002
Rev.00 Jun 03, 11
CL415 - DBC
DENT & BUCKLE CHART
RH Propeller
DBC-CR-002
Rev.00 Jun 03, 11
Reg. Marks: I-DPCR
LH Propeller
L
BLADES FILLING INSTRUCTIONS
Underline numbering defect on above assembly to indicate
which blade is damaged and report same number on the
detailed drawing on the left on specific position.
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
Page 8 of 10
DBC-CR-002
Rev.00 Jun 03, 11
CL415 - DBC
DENT & BUCKLE CHART
Rev.00 Jun 03, 11
Reg. Marks: I-DPCR
Windows RH View
Windows LH View
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
DBC-CR-002
Page 9 of 10
DBC-CR-002
Rev.00 Jun 03, 11
CL415 - DBC
DENT & BUCKLE CHART
Item
n°
Description & Dimension
Date
Inspector
Signature
Acceptable, Temporary action
and/or Repair
DBC-CR-002
Rev.00 Jun 03, 11
Reg. Marks: I-DPCR
Date
Inspector
Signature
A
T
A
T
A
T
A
T
INAER Form ENG 007 Rev 02 - DBC dent & buckle chart 415.dot
Page 10 of 10
DBC-CR-002
Rev.00 Jun 03, 11