ouTdoor ScrEEn rollEr blInd

outdoor screen roller blind
Installation Instructions
Your Windoware Outdoor Screen Roller Blind comes complete with all parts and
fixing accessories for a quick and easy installation. The only tools you will require
are a 1/8” drill bit, a Phillips Head screwdriver, tape measure and a pencil.
Note: The screws provided are for use with timber only. Please see your dealer for
recommendations when installing your blind against other materials.
STEP 1
Mark the holes where the screws will go.
Use the table (Fig.1) to determine how
far apart the brackets will be for your size
roller.
(Fig.1)
FABRIC
WIDTH
SCREW TO SCREW
measurement
after installation
1.2m
1225mm
1260mm
1.5m
1525mm
1560mm
1.8m
1825mm
1860mm
2.1m
2125mm
2160mm
2.4m
2425mm
2460mm
TOTAL WIDTH
STEP 2
Screw the Idle Plug unit and Clutch unit
into place. The Clutch unit will go on the
right while the Idle Plug unit will go on the
left. Do not tighten screws completely.
Clutch unit
Idle Plug unit
STEP 3
Insert the Clutch plug into the clutch
unit. While holding the roller, insert the
other side (Idle End plug) into the Idle
Plug unit. It should snap into place with a
bit of pressure. Adjust brackets for a snug
fit. Tighten screws to lock both brackets
in place.
Clutch plug
Idle end plug
furnishing solutions with style!
STEP 4
Install the Tension Device. Feed the chain through the pulley as shown. Position
the base so that the cord is taut and operable but not loose. It should only
have enough slack to operate when pulled up or down, do not twist or slant
the chain. Screw the base into place. Click the cover over the base and screw
in place.
WARNING:
Blind Cords may create a
strangulation hazard for
young children.
KEEP BLIND CORDS OUT
OF REACH OF CHILDREN.
Tension device base
cover
To avoid creating a possible strangulation hazard for children, the
corded internal window covering must be installed in such a way that a
loose cord cannot form a loop 220mm or longer at a height of less than
1600mm above floor level.
- A cord guide may be installed lower than 1600mm above floor level if
the cord is sufficiently secured or tensioned to prevent a loop 220mm or
longer from being formed.
- If a cord guide is installed lower than 1600mm above floor level it must
be designed to prevent a child from being able to remove the cord.
- If a cleat is used to secure the cord it must be at least 1600mm above
floor level because a child is capable of unwinding a cord from a cleat.
STEP 5
Install the Tie Downs (Optional).
This is used to secure your roller in
light breezes. Remove the end caps
from the bottom rail. Slide the Tie
Downs into the groove, once this
is done replace the end caps. You
will need something to anchor the
Tie Downs to such as a hook which
should be sourced seperately from
your hardware store.
Bottom rail
Tie Down
ADJUST CHAIN TENSION
To adjust the tension in the chain you
must first slide off the cover on the Clutch
unit. Once it is off you will see four screws
as shown below. To loosen the tension
turn the screws anti-clockwise. To tighten
the tension turn the screws clockwise.
ADJUSTING FOR CEILING INSTALLATION
To make the chain operate from the top such as the ceiling you will need to make
adjustments to both the Clutch unit and Idle plug unit. Slide the covers off both units
and remove the screws. As we did before when adjusting the chain for left hand
control turn the inner chain apparatus inside the Clutch unit 90 degrees so it will
hang down.
Idle Plug unit-remove screws
ADJUSTING FOR A LEFT HANDED
CHAIN CONTROL
To make the chain operate on the left
hand side, begin by sliding the cover
off the Clutch unit. You will expose four
screws used for adjusting the tension.
Unscrew these to access the inner chain
apparatus as shown below. Turn this 180
degrees so the chain can hang from the
left side. Replace the screws and cover.
There is no need to do anything to the Idle
plug unit. Lastly, pull out the end plugs on
the tube and switch them around.
down
In the Idle plug unit, once you have removed the screws as shown below, you will
see the inner apparatus which holds the end plug in place. Turn this so the opening
is facing down or away from the ceiling. Once this is done, replace the screws and
covers for both units and proceed with installation.
Clutch unit-remove screws
down
Australia 02 9741 4099
New Zealand 64-3-366 9810
www.windoware.com.au
furnishing solutions with style!
WARNING:
We strongly recommend
that in strong wind
conditions, you
completely retract your
Outdoor Screen Roller
Blind to prevent damage
to it and your windows.