user manual

G501975PCEMU32
USER MANUAL
PC I Express Multi I/O C ard
VER:1.0
ALL other company and product names are trademarks or registered trademarks of their respective owners
1
1. Featur es
1) . PCI Exp res s
. F ully compliant with PCI Express Base Specification, Revision 1.0a
. PCIe Multi F unction Peripheral controller with x1 Lane Interface
. Support for D1, D2, D3hot and D3cold
. Utilizes 100-MHz Differential PCI Express Common Reference Clock
. Support PCIe P ower Management
Please note some sections of the manual are only applicatable for the production that have such functions.
2) . Seria l Po r t
. F our 16c450/550/Extended 550 compatible UARTs
. Supports RS232, RS 485 & RS422 modes
. Bi-directional speeds from 50 bps to 16Mbps/Port
. F ull Serial modem Control
. Supports Hardware, Software flow control
. 5,6,7,8 and 9-bit Serial fo rmat support
. Even,Odd,None,space & Mark parity supported
. Custom BAUD Rates supported with external clock or by programming internal PLL
. On Chip 256 Byte depth F IF Os in Transmit, Receive path of each Serial Port
. Supports remote wakeup and power management features
. Serial Port transceiver shutdown support
. Support Slow IrDA on all Serial Ports
3) . I EEE12 84 Pa ralle l Po r t
. Multi-mode IEE E1284 compliant controller(SPP,PS2,EPP,ECP)
. F aster data rates up to 1.5Mbps for parallel port
2. In s ta lling the PCI Exp res s I/O ca rd to yo ur compu te r
1). Turn off your computer and all devices connected to it.
2). Remove the Computer
cover, Refer to your computer user
3). F ind an unused PCI Express
manual for more details.
slot and remove the metal bracket. Save the bracket screw
for later use.
4). Align the card horizontally with respect to the PCI slot and insert it into the slot. Once you have properly
positioned the PCI Express I/O card into the slot. secure the PCI Express I/O card with the bracket screw you
have saved.
5). replace the computer
cover
6). Replace the computer
cover.
3. Appli cat i ons
. Serial Attached Devices
. Serial Networking/Monitoring Equipment
. Data A cquisition System
. POS Terminal & Industrial PC
. parallel/Printer Port based applications
. Add-On I/O Cards -Serial/Parallel/USB
. Embedded systems - For I/O expansion
2
4. Softw are Suppor t
. D O S / W indow s98/ 98e/ M E
. W indow s 32bit 2000/ X P / 2003 S erver / V ist a & W indow s 64bit X P / 2003 S er ver / V ist a
. Linux K ernel 2. 6. 11 & above
. M A C 10. 4 & above
1). Driver Locations
A ll t he dr iver s f or t he Follow ing P C I E xpr ess cards are locat ed in t hese direct or ies of t he D r iver C D .
: \ M oschip\ M C S 9901\ D O S \ V er sion1. 0. 0. 0 D O S
: \ M oschip\ M C S 9901\ W in32_64B it \
: \ M oschip\ M C S 9901\ V ist a32_64B it
: \ M oschip\ M C S 9901\ Linux\ ver sion1. 6
: \ M oschip\ M C S 9901\ M ac
W indow s2000/ X P / 2003S er ver (32bit & 64bit )
W indow s V ist a ( 32bit & 64bit )
Linux
MAC
2). Installing DOS Driver
C opy " S X D O S I N . E X E" t o your har d disk and run " S X D O S I N . E X E", For m ore O pt ion, r ead "S X D O S I N . E X E / ?"
5. Installing W indows2O OO/X P/2003Ser ver/V ista Driver
I nst alling dr iver s f or t he f ir st t im e:
M ake sur e t hat you have not inser t ed P C I e car d int o P C I e slot .
R un P C I eset up. exe f ile f r om t he driver disk f older. You w ill see a w indow as show n below :
P r ess nstall?t o inst all t he dr iver.
W hen t he ? Hardware Installation?w izard prom pt s f or W indow s X P com pat ibilit y, Just click on
Continue Anyway .
3
Now shutdown the PC and insert the PCIexpress card into PCIe Slot and then Switch ON. F ound New
Hardware wizard will start and you have to select No, n ot th is time option.
Now select In s ta ll th e s oftwar e automatica lly (Re co mmen ded ) option and pressNext button to continue.
If the Hard ware I ns tallation wizard prompts for Windows XP compatibility, Just click on Co ntinu e
Any wa y ?
Click on Fin is h to complete the MosChip MCS9901 Peripheral Port installation.
F ollow the same above procedure to install the remaining MCS9901 peripheral ports.
6. Verifying Driver Installation
Please check the required configuration from Device Manager to confirm the proper installation.
F or Example proper detection of the MCS9901 PCIe Card (4 S erial) can be confirmed by viewing the
Device manager as shown below:
7. Serial Por t Properties Sheet
In the Device Manager Right Click on required Port and click on
Properties page.
roperties?Option to open the
General TAB :
T he
eneral?TAB provides you details about
evice Type?
anufacturer?and
T he ort Settings?TAB is used to configure parameters of the Serial Port.
evice Status?
Bits per Se con d selection is used to set the default Baud rate settings.
Data bits s elec tio n will have options 4,5,6,7 and 8 data bits.
Pa rity s elec tion will have Even,Odd, None, Mark and Space parity settings.
Stop bits s elec tio n will have 1,1.5 and 2 selections.
F low C ontro l s ele ction will have Xon_Xoff, Hardware and None settings.
If you want to change the Port Number click on
Number as shown below:
hange Port Number?and select the required P ort
4
T he Driver TAB shows the details of Driver Provider, Driver Release Date, Driver version is installed
on your PC and Digital Signer details as shown above.
8. Serial Por t Features and Mode Changes
By default every serial Port will be in RS 232 Mode.
If you want to change it into RS 42 2 OR R S 48 5 Mode select the appropriate Radio button as shown
below:
Con fig uring Ad va nc ed Bau d rates :
To Configure Advanced Baud rates click on
dv Baudrates?button.
5
By default
se Standard Baudrates?option is Enabled.
To configure custom Baud rate select
se Custom Baudrate?
Note: When
se Custom Baudrate?is selected, Serial Port baudrate is independent of the value set in
the Application
9. Pa ralle l Po r t Feature s a nd Mo de Cha nge s
Parallel Port F eatures:
Parallel port will support SPP/CBF IF O/ECP/EPP modes. By default Parallel Port will be in AUTO
mode. In this mode, Parallel port mode will be automatically configured to the required mode after
handshaking with the connected device.
10 . Unin s ta lling Drive rs
To Uninstall MCS9901 drivers, run
OSCHIP_PCIeUninst.exe?file available in the driver disk.
Note: Make sure that you should uninstall any previous driver before installing updated drivers.
6