2007 MR2 Manual

WARRANTY
REGISTRATION
O P E R AT I O N G U I D E
1) To turn the power ON, slide the Selector Switch located on the rear of the trigger frame UP to SEMI, BURST, or AUTO
mode. CAUTION: with the power ON, the marker is now ready to shoot.
2) Cock the marker by pulling the Snap T-Cocking Handle (part #266) rearward until it latches. Caution: If you let go before
P L E A S E CO M P L E T E A N D R E T U R N T H I S FO R M , A LO N G W I T H A CO PY O F YO U R P URCHASE RECEIPT,
W I T H I N 1 5 DAYS O F P U R C H A S E S O T H AT W E M AY VA L I DAT E YO U R 9 0 DAY L I M I T ED WARRANTY.
the Handle latches, your marker may fire. Note: The Snap T-Cocking Handle will latch the bolt internally, the Handle will
not remain in a cocked position after latching the bolt, nor will it move while the marker is being fired. You should hear an
audible click and feel a tension release in the Handle when cocking the marker.
3) Tighten the Air Tank until it is snug. If a leak occurs between the Tank and the C/A Adapter, replace the Tank O-ring.
4) Install the Loader onto the Feed Adapter (part #54A). Tighten the Feed Adapter Screw to secure the Loader, then fill
the Loader with .68 caliber paintballs only.
5) To change firing modes, slide the Selector Switch on the rear of the trigger frame to the desired mode.
6) It is recommended to use a motorized Loader that is capable of feeding paintballs into the marker at 13 balls per second
or faster to avoid chopping paintballs in the markers breach when shooting at high rates of fire.
NAME:
ADDRESS:
C I T Y:
STAT E :
ZIP:
CO U N T RY:
AG E :
JOB:
7) Routine lubrication of the marker does not require disassembly of the marker. Put 3-4 drops of Paintball Marker Oil into
the Bottom Line ASA (part #261), screw in your air tank, point the marker in a safe direction and dry fire (no paintballs in
PHONE #:
E-MAIL:
(
)
Y
/
the chamber) 5-10 shots. This procedure will circulate oil through the markers internal parts, thus extending the life of the
marker.
ITEM #:
PARTS LIST
! C AU T I O N !
This paintball marker is NOT a toy. It can cause serious injury or death.
Kingman recommends that customers be at least 18 years of age to purchase this product.
Firmly install a barrel blocking device when marker is not in use.
All persons using this product, or within range while this product is being used, must wear eye and face protection specifically designed
for paintball.
Never shoot a person who is not wearing proper protection.
Treat every paintball marker as if it were loaded.
Never look down the barrel of the marker.
Keep the paintball marker on SAFE until ready to shoot.
Always remove gas source before disassembly.
Fire only 0.68 caliber paintballs from this product.
Read this manual and air system warnings before using this product.
Any modifications or tempering of original factory parts will void all warranties and liabilities from Kingman.
Always make certain the bolt is in the un-cocked position when marker is not in use.
Always put marker on SAFE when marker is not in use.
Transfer this instruction manual upon change of marker ownership.
ITEM #:
N A M E O F PA R T S :
271
ITEM #:
N A M E O F PA R T S :
ITEM #:
N A M E O F PA R T S :
8) Only use oil that is specifically designed for paintball markers.
9) It is a good practice to lubricate your marker before and after each use, especially when storing the marker for an
NAME OF PARTS:
MR2 Trigger Frame
272
MR2 Touch Switch w/ Wire Harness
273
Blade Trigger
2 98
Trigger Set Screw
49*
Trigger Pin
JE12
Sear
PRODUCT NAME/MODEL:
W H AT OT H E R B R A N D ( S ) O F M A R K E R S D O YO U OW N ? :
extended period of time.
10) When you are finished shooting the marker, be sure to remove the Loader and all paintballs before storing. NOTE: there
W H Y D I D YO U P U R C H A S E T H I S K I N G M A N M A R K E R? :
may be a paintball in the breach of the marker, take a couple of shots in a safe direction to make sure that the Barrel and
breach are empty.
11) Place the Barrel Plug into the Barrel to avoid accidental discharge of the marker. Turn the marker OFF and slowly
1
Ba r re l P l u g
14
Va l ve B o d y
296
Ve l o c i t y Ad j u st e r w/ S p r i n g G u i d e
JE31E
ESP Sear Spring
unscrew the air source tank. Caution: do not remove the Tank Valve from the Tank, doing so may cause serious injury or
24 8
M R 1 / M R 2 1 2 ' Ba r re l
14 A
Va l ve B o d y Ro l l P i n
2 97
Ve l o c i t y Ad j u st e r O - r i n g
49C
Touch Switch Roll Pins
death.
3
Ba l l St o p p e r
15
Va l ve B o d y S c rew
262
M R 1 / M R 2 Q u i c k D i s co n n e c t P i n
49B
Sear Roll Pin (Small)
249
M R 1 / M R 2 Fe e d N e c k
294
M R 1 / M R 2 M 4 x 8 S c rew w/ wa s h e r
25
St r i ke r S p r i n g
274
MR2 Circuit Board
250
M R 2 S h ro u d
16
M 5 x 1 2 S c rew w/wa s h e r
26A
St r i ke r B u f fe r
JE2 9
Circuit Board Screw
2 51
M R 2 Re ce i ve r
256
M R 2 D e l r i n AC S B o l t
2 63
M R 2 S i g ht Ra i l
JE18C
Coil Set
252
M R 2 Ve r t i ca l / C /A P l u g
JE18A
St r i ke r B o l t
264
M R 2 S i d e P l at e ( Le f t )
JE18E*
Coil Set Screw
2 53
M R 2 Ve r t i ca l / C /A t o H o s e Ad a pt e r
19A
St r i ke r O - R i n g
265
M R 2 S i d e P l at e ( R i g ht )
E24A
Battery Harness
254
M R 2 Re s e r vo i r Ad a pt e r P l u g
20
Ba r re l O - r i n g
266
M R 2 S n a p T- Kn o b
275
MR1/MR2 Shoulder Stock
255
M R 2 S h ro u d P l u g
257
MR2 Bolt Pin
2 67
M R 2 S n a p T- C l i p
JE1015
Java 9.6v Rechargeable Battery
09
O-Ring #015 80D
258
M R 1 / M R 2 2 " D ove t a i l D ro p Fo r wa rd
268
M R 2 S n a p T-S p r i n g
JE1024*
A/C Charger - 110 v
10C
Va l ve S p r i n g
2608s
D ro p Fo r wa rd Lo c k S c rew
269
M R 2 S n a p Ra i l Cove r
276*
MR2 Parts Kit
11
Cu p S ea l G u i d e
2 59
M R 2 Fo re G r i p H a n d l e
290
D i s co n n e c t H o s e 6. 2 5" ( b l a c k )
37B
Filter O-ring
12
Cu p S ea l
260
M R 1 / M R 2 St r i ke r P l u g
2 83
M a l e ST D / Fe m a l e M e t r i c
37C
Air Filter
13
Va l ve P i n
261
M R 1 / M R 2 D ove t a i l B ot t o m - L i n e A S A
2 70
M R 2 G r i p Pa n e l s
37D
Disconnect O-ring #011
12) Trigger Set Screws (#JE31L) have been positioned by the factory on the A and D setting. This is a factory setting that
will minimize the trigger bounce. You can reposition the Trigger Screws (#JE31L) for your desired setting: A and C, A and
D, B and C, or B and D. Important: You must use #242 Loc-Tite (blue color) every time the Trigger Set Screws are
repositioned to prevent the loosening of Screws. Turn Trigger Screws 1 & 2 (#JE31J) clockwise or counter clockwise
W H AT I S T H E N EX T PA I N T B A L L P R O D U C T YO U I N T E N D TO B U Y ? :
W H AT A R E YO U R H O B B I E S (OTHER THAN PAINTBALL) ? :
W H AT A R E S O M E M AG A Z I N E S YO U L I K E TO R E A D? :
H AV E YO U M A D E A N Y O N L I N E P U R C H A S E S I N T H E PA ST 6 M O N T H S? :
N
(depending on your current setting) until desired trigger bounce is reached.
CO M M E N T S / S U G G E ST I O N S :
M A I L TO :
* not pictured
KINGMAN GROUP
14 0 1 0 L I V E OA K AV E .
B A L DW I N PA R K , CA 91706 USA
KINGMAN GROUP
WA R R A N T Y STAT E M E N T
Kingman warranties to the original customer/purchaser that this product is
free from defects in material and workmanship under normal use and service
for a period of 12 months from the original date of purchase by the initial
owner/pu rchaser. For warranty to be effective, customer must return the
enclosed warranty registration card, along with a copy of the purchase
receipt, within fifteen days of purchase. Kingman agrees to repair or replace
(at its discretion) any product within a reasonable period of time. This
warranty does not cover o-rings, 9.6v rechargeable battery, charger,
scratches, nicks, normal wear and tear of parts, any modifications or normal
fading of anodizing or damage caused by dropping or hitting of products. This
warranty shall not apply if it is shown by Kingman that the consumer caused
the defect or malfunction because of misuse. This warranty only covers
original factory parts. Any modifications or tampering with original factory
parts will not be covered by this warranty. Any damage caused by water will
not be covered by this warranty. Warranty repair labor may only be conducted
by Kingman technicians or by technicians authorized by Kingman to perform
warranty repairs. If product needs repair, package it carefully and send
together with your name, address, phone number and a brief description of
the malfunction to:
HELPFUL HINTS
C H A R G I N G I N ST R U C T I O N A N D S P E C I F I C AT I O N S FOR
R E C H A R G E A B L E B AT T E RY
Fi r i n g ve l o c i t y m ay va r y a cco rd i n g t o a l t i t u d e a n d c l i m at e co n d i t i o n s .
A l way s re m ove A i r Ta n k b e fo re a ny d i s a s s e m b l y o f yo u r m a r ke r. D O N OT re m ove t h e Va l ve B o d y ( # 14) u n l e s s
T h e bat t e r y t o b e u s e d w i t h yo u r f ra m e i s a s p e c i a l l y d e s i g n e d 9.6 Vo l t N i M H Bat t e r y. To maximize the life
B E FO R E u s i n g yo u r m a r ke r i n p l ay, yo u m u st a l way s f i r st p e r fo r m a S A F E V E LO C I T Y T E ST. T h i s ca n o n l y
s p e c i f i c Va l ve B o d y re pa i r s a re n e e d e d . If n e e d e d , re m ove Va l ve B o d y w i t h a l o n g , s o f t- t i p p e d o b j e c t s u c h a s t h e
o f t h e Bat t e r y, p l ea s e rea d t h e fo l l ow i n g i n st r u c t i o n s b e fo re u s e.
I M P O R TA N T
b e a cco m p l i s h e d by u s i n g a t e st i n g d ev i ce ca l l e d a Ve l o c i t y C h ro n o g ra p h a n d ca n b e p e r fo r m e d by t h e
e ra s e r e n d o f a p e n c i l . D O N OT re m ove t h e Va l ve B o d y w i t h a s c rewd r i ve r a s i t w i l l d a m a g e t h e Va l ve B o d y a n d
d ea l e r s h i p w h e re yo u p u rc h a s e d t h i s p ro d u c t o r at a l o ca l pa i nt ba l l p l ay i n g f i e l d .
ca u s e a i r l ea ks . ( N ot e : # 1 5 s c rew m u st b e re m ove d p r i o r t o t a k i n g o u t t h e Va l ve B o d y )
CO N N E C T I N G T H E B AT T E RY
N OT E : T h i s p ro d u c t i s i nt e n d e d t o b e u s e d at a ve l o c i t y n o g reat e r t h a n 3 0 0 fe e t p e r s e co n d ( F P S ) .
A i r l ea ks d ow n t h e ba r re l a re u s u a l l y ca u s e by a d a m a g e d o r wo r n Cu p S ea l ( # 1 2 ) . Re p l a ce w i t h a n ew Cu p S ea l .
Re m ove t h e l e f t G r i p Cove r ( pa r t # 2 70) . T h e Bat t e r y Te r m i n a l i s l o cat e d t o t h e l e f t o f t h e Circuit Board.
Re co m m e n d e d ve l o c i t y i s 2 8 0 F P S o r l e s s .
To a s s u re m a r ke r i s a s s e m b l e d p ro p e r l y, fo l l ow t h e s c h e m at i c d raw i n g o r ca re f u l l y a r ra n g e pa r t s i n o rd e r d u r i n g
At t a c h t h e Bat t e r y t o t h e Bat t e r y Co n n e c t o r s by a l i g n i n g t h e + ( p o s i t i ve ) t e r m i n a l o n t h e Battery
T h i s p ro d u c t i s N OT i nt e n d e d t o b e u s e d at a ny d i st a n ce l e s s t h a n 2 5 fe e t .
d i s a s s e m b l y. Pa r t s a s s e m b l e d ba c kwa rd s o r p l a ce d i n t h e w ro n g o rd e r w i l l ca u s e m a r ke r t o m a l f u n c t i o n .
Co n n e c t o r t o t h e + ( p o s i t i ve ) t e r m i n a l o n t h e Bat t e r y.
T h i s pa i nt ba l l m a r ke r m ay h ave exce s s g a s a f t e r re m ova l o f t h e C 0 2 o r Co m p re s s e d A i r t a n k . P l ea s e re m ove
a l l pa i nt ba l l s a n d d i s c h a rg e t h e re m a i n i n g g a s s a fe l y.
A l way s p u t m a r ke r o n S A F E w h e n m a r ke r i s n ot i n u s e.
CO 2 / H P A I R TA N K WA R N I N G
Fax no.: 626.851.8530
www.kingman.com
a n d ca u s e i t n ot t o ex pa n d i nt o g a s ( ca r b o n d i ox i d e ) at a co n s i st e nt rat e.
w i l l vo i d a l l Ki n g m a n wa r ra nt i e s a n d l i a b i l i t i e s o n yo u r m a r ke r. Ki n g m a n Re co m m e n d s t h at you use the
S pyd e r 9.6 vo l t N i M H Re c h a rg ea b l e Bat t e r y ( # J E 1 0 1 5 ) a n d S pyd e r C h a rg e r ( s ) s u p p l i e d with your marker.
b. M a r ke r n e e d s l u b r i cat i o n . ( S e e O P E R AT I O N G U I D E i n P 4)
R E C H A R G I N G T H E B AT T E RY A F T E R I N I T I A L U S E
c . T h e St r i ke r O - r i n g ( # 1 9 A ) i s d a m a g e d . Re p l a ce w i t h n ew Ki n g m a n o r Ki n g m a n -a p p rove d O - r i n g . ( N OT E :
A f u l l y c h a rg e d Bat t e r y w i l l p rov i d e a b o u t 5,0 0 0 -1 0,0 0 0 s h ot s u n d e r n o r m a l u s e co n d i t ions. The actual
Improper use, filling, storage or disposal of this cylinder may result in death, personal injury and/or property damage.
This cylinder must be filled only by properly trained personnel in accordance with CGA Pamphlets P.1 and G-6.3
available from the Compressed Gas Association - www.CGANET.COM.
Do not over pressurize. Do not expose pressurized cylinder to temperatures in excess of 130 degrees F.
Do not expose cylinder to corrosive materials and do not clean with caustic cleaners.
t h e # 1 9 A O - r i n g ca n n ot b e s u b st i t u t e d by a t a n k O - r i n g o r a # 9 O - r i n g ) .
Cylinders heated to a temperature of 250 degrees Fahrenheit or more must be condemned or requalified in accordance with
test defined in CFR-49.
Keep cylinder out of reach of children.
The valve should NEVER be detached from the canister. Should this occur, please seek assistance from a trained
airsmith immediately.
Any tank packaged with this marker is intended for paintball use only.
DA N G E R
doubt, screw the cylinder back onto the marker and contact a trained person for repair.
GENERAL MAINTENANCE
C l ea n i n g s h o u l d o n l y b e p e r fo r m e d o n t h e ex t e r i o r o f t h e m a r ke r. Avo i d s u b m e rg i n g t h e m a r ke r i n l i q u i d fo r
a ny rea s o n a s t h i s ca n ca u s e d a m a g e t o t h e e l e c t ro n i c s . Ke e p wat e r o r c l ea n i n g s o l u t i o n s f ro m e nt e r i n g
i n s i d e t h e Tr i g g e r Fra m e. H a r s h s o l ve nt s s h o u l d n ot b e u s e d t o c l ea n a ny pa r t o f t h e M a r ke r. A l way s u s e t h e
a p p ro p r i at e t o o l s t h at a re s u p p l i e d w i t h t h e m a r ke r t o re m ove s c rew s a n d ot h e r co m p o n e nt s .
s h ot s w i l l d e p e n d o n t h e m a r ke r s a n d t h e t y p e o f u s e. D u e t o t h e c h a ra c t e r i st i c s o f t h e NiMH Battery, it
d . N e e d t o c l ea n Ba r re l a n d u p p e r c h a m b e r o f t h e Re ce i ve r.
wo n ' t b e n e ce s s a r y t o co m p l e t e l y d ra i n t h e Bat t e r y b e fo re re c h a rg i n g i t . Yo u ca n c h a rg e the Battery any
e. Pa i nt ba l l s m ay b e d e fe c t i ve ( i .e. ex p i re d , o d d s h a p e, e t c . )
t i m e yo u wa nt a n d t h e t i m e n e e d e d t o f u l l y c h a rg e w i l l d e p e n d o n h ow m u c h e n e rg y i s l e f t in the Battery.
f. Af t e r ba l l b rea ks i n Ba r re l o r c h a m b e r, re m ove a l l pa r t s f ro m U P P E R c h a m b e r o f Re ce i ve r, w i p e pa r t s
T h e m o re e n e rg y l e f t i n t h e Bat t e r y, t h e s o o n e r i t w i l l a c h i eve a f u l l c h a rg e.
c l ea n , a n d rea s s e m b l e pa r t s i nt o Re ce i ve r. A l s o m a ke s u re t o c l ea n t h e Ba r re l w i t h a s q u e e g e e.
Do not alter this cylinder in any way.
the cylinder rather than remaining stationary with the marker. STOP if the Valve starts to unscrew from the cylinder. If in
Phone no.: 626.430.2300
a . T h e p re s s u re i n t h e t a n k i s t o o l ow. I n s o m e ca s e s , t h e weat h e r ca n a f fe c t t h e l i q u i d i n t h e CO 2 t a n k
BOTTLE MUST BE RETESTED PERIODICALY - SEE CO2/HP TANK LABEL FOR RETEST DATE!
the cylinder head. LOOK at the Valve when removing the cylinder from the marker. Be sure that the valve is turning with
Baldwin Park, CA 91706 U.S. A .
O N E O R M O R E O F T H E FO L LOW I N G M AY C AU S E R E CO C K I N G R E L AT E D P R O B L E M S :
WA R N I N G
Us i n g u n s p e c i f i e d bat t e r i e s o r c h a rg e r s co u l d ca u s e d a m a g e t o t h e C i rc u i t B oa rd . S u c h u nauthorized use
VALVES MUST BE INSTALLED OR REMOVED ONLY BY QUALIFIED PERSONNEL.
The CO2 or Compressed Air Tank can fly off with enough force to cause serious injury or death if the Valve unscrews from
14010 Live Oak Avenue
T R O U B L E S H O OT I N G
E L E C T R O N I C G R I P T R O U B L E S H O OT I N G
a . C h e c k t o m a ke s u re t h e re i s e n o u g h a i r p re s s u re t o f i re t h e m a r ke r.
N OT I C E: It i s re co m m e n d e d t h at t h e Bat t e r y b e c h a rg e d p r i o r t o u s e i n o rd e r t o e n s u re maximum perform a n ce, e s p e c i a l l y i f t h e Bat t e r h a s n ot b e e n u s e d fo r ove r a we e k .
b. Bat t e r y m ay n e e d t o b e re c h a rg e d .
L I F E O F B AT T E RY
c . S p e c i f i c t ro u b l e s h o ot i n g q u e st i o n s m ay b e a n swe re d by ca l l i n g t o l l f re e at
Wi t h t h e S pyd e r C h a rg e r s , a n d u n d e r n o r m a l u s e co n d i t i o n s , t h e Bat t e r y ca n rea c h 70 0 - 1000 charge-
(8 8 8) K I N G M A N o r ( 6 2 6 ) 43 0 - 2 3 0 0.
re c h a rg e c yc l e s b e fo re ex p i rat i o n .
T H E C H A R G E R FO R T H I S B AT T E RY
TO U R N A M E N T M O D E S E T T I N G
T h i s c h a rg e r i s s p e c i a l l y d e s i g n e d fo r a 9.6 vo l t Re c h a rg ea b l e Bat t e r y. Fi ve t y p e s o f c h a rg e r s a re c u r re nt l y ava i l a b l e
T h e S pyd e r M R 2 C i rc u i t B oa rd ( pa r t # 2 74) i s e q u i p p e d w i t h a To u r n a m e nt Lo c k O u t Sw i t ch (#JE30B). When
f ro m yo u r Ki n g m a n D ea l e r :
t h e To u r n a m e nt Lo c k O u t Sw i t c h i s re m ove d f ro m t h e C i rc u i t B oa rd t h e m a r ke r ca n o n l y fire in SEMI-AUTO
1 . S pyd e r Ra p i d St a n d a rd I n d o o r 1 1 0 v A /C C h a rg e r ( # J E 1 0 2 6 )
m o d e. T h i s s h o r t- c i rc u i t c l i p i s l o cat e d o n t h e i nt e r n a l C i rc u i t B oa rd t o t h e r i g ht o f t h e Battery. Reattaching
2 . S pyd e r Ra p i d C a r C h a rg e r ( # J E 1 0 2 2 )
t h e To u r n a m e nt Lo c k O u t Sw i t c h ( # J E 3 0 B ) ba c k i nt o t h e C i rc u i t B oa rd w i l l re - e n a b l e t h e multi-mode
3 . S pyd e r St a n d a rd I n d o o r 1 1 0 v A /C C h a rg e r ( # J E 1 0 24)
functions.
4. S pyd e r St a n d a rd 2 B I n d o o r C h a rg e r ( # J E 1 0 2 3 )
5. S pyd e r St a n d a rd I n d o o r 2 2 0 v A /C C h a rg e r (J E 1 0 2 5 )
I M P O R TA N T ! Fo r o pt i m a l p e r fo r m a n ce, Ki n g m a n re co m m e n d s t h at a n a g i t at o r Loa d e r b e used in order to
Us i n g a St a n d a rd C h a rg e r ( # J E 1 0 24 -J E 1 0 2 5 ) i t w i l l t a ke a p p rox i m at e l y 6 - 8 h o u r s t o f u l l y c h a rg e t h e 9.6 vo l t
s h o ot at h i g h rat e s o f f i re. Ki n g m a n a l s o re co m m e n d s t h e u s e o f a S pyd e r CO 2 A i r Ta n k or High Pressure Air
Bat t e r y. Us i n g t h e Ra p i d C a r/ H o m e C h a rg e r ( # J E 1 0 2 2 / 1 0 2 6 ) w i l l t a ke a p p rox i m at e l y 1 . 5 h o u r s t o a c h i eve a f u l l
Ta n k t o o p e rat e t h i s m a r ke r. L a st l y, t h e u s e o f t o u r n a m e nt g ra d e pa i nt w i l l h e l p re d u ce t he likelihood of
Bat t e r y c h a rg e.
pa i nt ba l l b rea ks w h e n f i r i n g t h e m a r ke r.