Color Cements for Masonry - Lafarge in North America

CEMENT
Custom Color Masonry
Rich color cements for masonry
page 2 | Lafarge Cement
CEMENT
Raleigh Convention Center, Raleigh, North Carolina.
Lafarge Savannah Ivory and Seaside Type S Color
Masonry Cements are used for the brick mortar
joints and Lafarge Magnolia® Type S Masonry
Cement is used for the block mortar joints.
Lafarge in
North America
The Lafarge Group is the
world leader in building
materials, with top-ranking
positions in all of its
businesses: Cement,
Aggregates & Concrete
and Gypsum. The Group
employs 78,000 employees
in 78 countries. Lafarge
is the largest diversified
supplier of construction
materials in the United
States and Canada.
The Lafarge Group places
innovation at the heart of
its priorities, working for
sustainable construction
and architectural creativity.
Custom Color Masonry
>Specifications Lafarge’s Custom Color
Masonry Cements comply with the
requirements of ASTM C 91. Properly
mixed with 2-1/4 to 3 parts sand conforming to ASTM C 144, the mortar
should exceed the requirements of ASTM
C 270 for Type N, Type S or Type M.
>Custom Colors Although the color
samples shown on page 7 are the colors
most in demand, some projects call for
other shades. Lafarge will be happy to
work with its clients to develop the
required color. As color can be affected
by certain sands used on job sites,
Lafarge Masonry Cements can be custom
colored so that available sand can be
used. All of the samples produced by
Lafarge are made with white sand to most
accurately demonstrate the color potential
of the cement.
FRONT COVER and bottom right PHOTOs
ImaginOn: Joe and Joan Martin Center,
Charlotte, North Carolina. Lafarge Color
Masonry Cement is used in the brick mortar
joints.
page
page
2 2| Lafarge
| Lafarge
Cement
Cement
> Cleaning color mortar Improper cleaning
methods can damage a structure. Cleaning
colored mortar requires special attention.
Muriatic acid should not be used to clean
walls built with mortar containing Lafarge
cement. The masonry cleaning recommendations of the manufacturer of the
masonry unit should be followed.
>Light Colors Light color cements for
masonry should be mixed with sand that
is lighter in color than the cement for
masonry. Light color cements for masonry
mixed with a dark sand will produce a
mortar that is darker than the cement.
Portland & Lime
Lafarge Eaglebond® Portland & Lime is
a premix of portland cement and Type S
hydrated lime and is formulated for use
as a prepared portland and lime cement.
It is available in natural grey, and in case
the project calls for a special custom
blended shade, this can also be accomodated. Available in Type N, Type S and
Type M formulations.
Mortar Cement
Lafarge Mortar Cement complies with
ASTM C 1329. Custom color mortar
cements are available as a special order
item.
> Product color Where possible the colors
used in the manufacturing process are
derived from sustainable sources.
page 3 | Lafarge Cement
CEMENT
Colors that last
Lafarge Masonry Colors last longer
because the finest ingredients available
are used. The homogenization process
is one of the most advanced and sophisticated in the industry. Practically speaking, the color pigment and the cement
particle become one. That is why the rich
beautiful colors endure.
A sample of what Lafarge
offers
In order to make precise color selections
easier, an extensive choice of colored cements is offered. Joint-size color sticks
are available for all standard colors, as
well as for many of the custom colors
developed over the years. If a new custom color is required, a sample stick in
the new color can be provided. Sample
brick panels mounted on boards can also
be sent to the Lafarge color lab for color
matching.
page 4 | Lafarge Cement
Wollersheim Winery, Prairie du Sac, Wisconsin.
Lafarge Mortar Cement is used for the mortar joints
in the facade.
Kuhlman Corporate Office, Maumee, Ohio.
Lafarge Masonry Cement is used for the brick
mortar joints.
Quality control
Lafarge’s quality control program
ensures that all products are tested for
conformance to ASTM Standards. Tests
include strength, workability, water
retention, board life and plasticity. The
products are tested and inspected to
ensure that Lafarge provides the finest,
most consistent color masonry cement
products on the market.
State-of-the-art
production facility
The recently updated and automated
Lafarge facility ensures product quality
and consistency. The Lafarge production
team ensures that the market is provided
with superior masonry products.
page 5 | Lafarge Cement
CEMENT
Specification Data
Product Name
Lafarge Masonry Cements:
Type N, Type S and Type M
Manufacturer
Lafarge North America Inc.
Lafarge Building Materials Inc.
12018 Sunrise Valley Drive
Suite 500
Reston, VA 20191
www.lafarge-na.com
Product Description
> Basic Use Lafarge Masonry Cements
are specially formulated and manufactured for the production of masonry
mortar for use in brick, block, and stone
masonry construction. Masonry cements
may also be used to produce stucco.
> Composition and Materials Lafarge Masonry Cements are composed of portland
cement, plasticizers, and other agents
which promote enhanced workability and
extended board life. These components
are proportioned at the cement plant
under controlled conditions to assure
uniformity of performance.
> Types Lafarge Masonry Cements are
produced in Type N, Type S and Type M.
Limitations
Lafarge Masonry Cements are designed
to be mixed with sand and water to
produce masonry mortar. The addition
of hydrated lime to a Lafarge masonry cement mortar at the job site is not
required or recommended.
Physical Properties
Precautions
Lafarge Masonry Cement mortars provide
an excellent level of performance in the
functional areas of workability, strength,
durability and appearance.
Direct contact with wet cement should
be avoided. If contact occurs, the skin
should be washed with water as soon as
possible. Exposure can cause serious,
potentially irreversible tissue destruction
in the form of chemical (caustic) burns.
If cement gets into the eyes, immediately rinse thoroughly with water and seek
medical attention. For more information,
reference the applicable Lafarge Material Safety Data Sheet (MSDS). The MSDS
should be consulted prior to use of this
product and is available upon request
and online at www.lafarge-na.com.
The following is a general guide for selection of mortar type. Other factors such
as type and absorption of masonry units,
climate and exposure, applicable building codes and engineering requirements
should also be considered.
Recommended Guide
for Selection of Mortar Type
Building Segment
Mortar Type
Exterior above grade
load-bearing
S
non-load-bearing
N
parapet wall
S
Exterior at or below grade
and pavers
S or M
Interior
load-bearing
N or S
non-load-bearing
N
Technical Data
Colors
> Applicable Standards Lafarge Masonry Cements conform to ASTM C 91,
the “Standard Specification for Masonry Cement,” used in the production of
mortars, Type N, Type S and Type M in
compliance with the proportion or property sections of ASTM C 270.
Lafarge Masonry Cements are available
in a variety of colors as well as in natural
grey.
page 6 | Lafarge Cement
Limited Warranty
Lafarge warrants that Lafarge Color Masonry Cements meet applicable ASTM
requirements. Lafarge makes no other
warranty, whether of merchantability
or fitness for a particular purpose with
respect to these products. Having no
control over their use, Lafarge will not
guarantee finished work in which these
products are used.
Call an
experienced
professional
Lafarge will be delighted to answer
any questions about its colors
and assist in the selection of the
ideal masonry cement formulation for a particular project.
1-800-331-0022
Certain products are available only
in particular geographic areas.
Please consult the local Lafarge
Cement representative for specific
product availability and ordering.
Custom Colors
CEMENT
All Lafarge Custom Color Cements as well as Lafarge Eaglebond® Portland & Lime and Lafarge Superbond® Mortar Cement are
available in pre-mixed formulations.
Specification Data
Manufacturer
Lafarge North America Inc.
Lafarge Building Materials Inc.
12018 Sunrise Valley Drive
Suite 500
Reston, VA 20191
www.lafarge-na.com
Product Description
> Basic Use Lafarge Masonry Cements
are specially formulated and manufactured for the production of masonry
mortar for use in brick, block, and stone
masonry construction. Masonry cements
may also be used to produce stucco.
> Composition and Materials Lafarge Masonry Cements are composed of portland
cement, plasticizers, and other agents
which promote enhanced workability and
extended board life. These components
are proportioned at the cement plant
under controlled conditions to assure
uniformity of performance.
> Types Lafarge Masonry Cements are
produced in Type N, Type S and Type M.
Lafarge Masonry Cements are designed
to be mixed with sand and water to
produce masonry mortar. The addition
of hydrated lime to a Lafarge masonry cement mortar at the job site is not
required or recommended.
Physical Properties
Precautions
Lafarge Masonry Cement mortars provide
an excellent level of performance in the
functional areas of workability, strength,
durability and appearance.
Direct contact with wet cement should
be avoided. If contact occurs, the skin
should be washed with water as soon as
possible. Exposure can cause serious,
potentially irreversible tissue destruction
in the form of chemical (caustic) burns.
If cement gets into the eyes, immediately rinse thoroughly with water and seek
medical attention. For more information,
reference the applicable Lafarge Material Safety Data Sheet (MSDS). The MSDS
should be consulted prior to use of this
product and is available upon request
and online at www.lafarge-na.com.
The following is a general guide for selection of mortar type. Other factors such
as type and absorption of masonry units,
climate and exposure, applicable building codes and engineering requirements
should also be considered.
Recommended Guide
for Selection of Mortar Type
Building Segment
Mortar Type
Exterior above grade
load-bearing
S
non-load-bearing
N
parapet wall
S
Exterior at or below grade
and pavers
S or M
Interior
load-bearing
N or S
non-load-bearing
N
Technical Data
Colors
> Applicable Standards Lafarge Masonry Cements conform to ASTM C 91,
the “Standard Specification for Masonry Cement,” used in the production of
mortars, Type N, Type S and Type M in
compliance with the proportion or property sections of ASTM C 270.
Lafarge Masonry Cements are available
in a variety of colors as well as in natural
grey.
page 6 | Lafarge Cement
Limited Warranty
Lafarge warrants that Lafarge Color Masonry Cements meet applicable ASTM
requirements. Lafarge makes no other
warranty, whether of merchantability
or fitness for a particular purpose with
respect to these products. Having no
control over their use, Lafarge will not
guarantee finished work in which these
products are used.
Call an
experienced
professional
Lafarge will be delighted to answer
any questions about its colors
and assist in the selection of the
ideal masonry cement formulation for a particular project.
LAFARGE Whitestone
LAFARGE Beige
LAFARGE Ivory Buff
LAFARGE Canyon Brown
LAFARGE Savannah Ivory
LAFARGE Lite Beige
LAFARGE Porcelain
LAFARGE San Tan
LAFARGE Blush
LAFARGE Clay Pink
LAFARGE Khaki
LAFARGE Cordova Tan
LAFARGE Oyster
LAFARGE Red
LAFARGE Seaside
LAFARGE Dark Brown
LAFARGE Lite Buff
LAFARGE Charcoal
LAFARGE Navajo
LAFARGE Black
LAFARGE Limestone
LAFARGE Magnolia® Mason’s Mix
LAFARGE Brown
LAFARGE Magnolia® Type “S”
LAFARGE Putty
LAFARGE Magnolia® Dark
LAFARGE Sahara
LAFARGE Magnolia® Ultra Dark
LAFARGE Georgia Red
LAFARGE Magnolia® Buff
1-800-331-0022
Certain products are available only
in particular geographic areas.
Please consult the local Lafarge
Cement representative for specific
product availability and ordering.
Colors shown approximate actual color mortar joints, but cannot be relied upon to be exact. Please contact your Lafarge Cement representative to request sample color mortar sticks.
Natural product colors
Product Name
Lafarge Masonry Cements:
Type N, Type S and Type M
Limitations
LAFARGE NORTH AMERICA INC.
Lafarge Building Materials Inc.
12018 Sunrise Valley Drive
Suite 500
Reston, VA 20191
www.lafarge-na.com
page 1 | 5/10
pbccme
Lafarge Cement