Double-Row Ball Bearings Customised Ball Bearings

Transcription

Double-Row Ball Bearings
Customised Ball Bearings
|2
CONTENTS
Double-row ball bearings and
customised ball bearings
Contents
Page 3
CONTENTS
Page 4
INDIVIDUAL SOLUTIONS
Page 5
PRODUCTS AND APPLICATIONS
Page 6
COMPANY PROFILE
Page 7
STANDARD PRODUCTION PROGRAMME
Page 8
SELF-ALIGNING BALL BEARINGS
Page 10
• Bore 10 – 35 mm
Page 12
• Bore 40 – 75 mm
Page 14
• With adapter sleeve, shaft 17 – 50 mm
Page 16
• With adapter sleeve, shaft 55 – 65 mm
Page 18
• Sealed both ends, bore 12 – 65 mm
Page 20
• With wide inner ring, bore 20 – 60 mm
Page 22
• With sleeve, shaft 20 – 50 mm
Page 24
DEEP-GROOVE BALL BEARING Double-row
Page 36
• Double-row, bore 10 – 90 mm
Page 28
ANGULAR-CONTACT BALL BEARING Double-row
Page 30
• Bore 10 – 75 mm
Page 32
• Double-row, bore 80 – 90 mm
Page 34
• Double-row, with filling slot, bore 10 – 70 mm
Page 36
PULLEYS
Page 38
• Pulleys, bore 10 – 35 mm
Page 39
Life factors Fh and speed factors Fn for ball bearings
|3
TAILORMADE SOLUTIONS
Flexible variation – solid precision
Everything is possible. NSK special bearings are manufactured according to your
specific requirements. The only thing 'standard' with all our products is the NSK
Quality.
Internal design for load ratings:
DIN / ISO 76
DIN / ISO 281
OUTER RING ACCORDING TO
CUSTOMER REQUIREMENTS
• Diameter
• Width
• With groove
• With bore/ thread
Profile
• Spherical
• Gothic arch
• V-profile
• Groove turned or ground
SEALS ACCORDING TO CUSTOMER
REQUIREMENTS
Standard
• ZR / 2ZR
• RSR / 2RSR
Special solutions
• Multi-lipped
• Labyrinth seal
• Three-part sealing
INNER RING ACCORDING TO
CUSTOMER REQUIREMENTS
Bore
• Diameter
• Cone
• Teeth
• Groove
• Thread
Width
|4
PRODUCTS AND APPLICATIONS
RADIAL INSERT BEARING WITH
DOUBLE-ROW
DOUBLE-ROW
BALL BEARINGS
CUSTOMISED BALL BEARINGS
OUTER RING
30 mm...180 mm external diameter
for applications such as the in-house
for harvesting machines (special designs,
(deep-groove, angular-contact and self-
design of double-row clutch-release
suitable for applications where there is
aligning ball bearings and various versions)
bearings based on standard bearing or
high exposure to contamination and for
new designs:
high-pressure cleaning)
• WHEEL BEARINGS
• WIRE-STRAIGHTENING MACHINES
• CONVEYOR BELTS
• BELT-TENSIONERS
• ELECTROMAGNETIC
• HOUSED BEARING UNITS
Deep-groove ball bearings in:
• FANS
CLUTCHES (FOR EXAMPLE)
• CHAIN CONVEYORS
• CONVEYOR EQUIPMENT
• AGRICULTURAL MACHINES
Angular-contact ball bearings in:
• LIFTING EQUIPMENT
• SUPPORT ROLLERS
• THE AUTOMOBILE INDUSTRY
• WOOD-PROCESSING MACHINES
• FANS
• SHAFT ENCODERS
• CHAIN PULLEYS
• GEARBOXES
• PULLEYS
• WOOD PROCESSING MACHINES
• PULLEYS FOR OVERHEAD CHAIN
• COMPRESSORS
CONVEYORS
• MAST GUIDE ROLLERS
• LINEAR GUIDES
• PUMPS
• ROPE PULLEYS
• WHEEL BEARINGS
• ALL TYPES OF TENSION PULLEYS
• BELT-TENSIONERS
• TACHOMETERS
Self-aligning ball bearings in:
• BLOWERS
• WOOD PROCESSING MACHINES
• AGRICULTURAL MACHINES
• EXTRACTION FANS
• TEXTILE MACHINES
• ROLLERS
|5
COMPANY PROFILE
Quality – made in Germany
Our products are manufactured in Germany to a high standard of quality and reliability, and our management system is certified in accordance with national and
international standards. We take responsibility for our total process – when it
comes to the environment, too: We take it for granted that raw materials and
energy must be used efficiently and that waste must be reduced to the minimum.
Certification according to
ISO/TS 16949:2002 including
DIN EN ISO 9001:2000 and
DIN EN ISO 14001:2004
Are you looking for something special? At NSK, you will find experts in all of our sales
offices. When it comes to meeting your requirements – whether they are standard or
special solutions - our staff are always at your service. The only thing we do not need to
discuss is quality. With us, meeting the highest standards is the norm.
Always at your service
Europe
Africa
PETERLEE
COVENTRY
MAIDENHEAD
NEWARK
RATINGEN
STUTTGART
MUNDERKINGEN
PARIS
BARCELONA
TURIN
MILAN
WARSAW
KIELCE
WALBRZYCH
ISTANBUL
JOHANNESBURG
|6
North America
MONTREAL
ANN ARBOR
FRANKLIN
PLAINFIELD
CLARINDA
MIAMI
SANTA FE SPRINGS
VANCOUVER
South America
BUENOS AIRES
SUZANO
SAO PAULO
MEXICO CITY
New Zealand
Australia
AUCKLAND
SYDNEY
BRISBANE
MELBOURNE
ADELAIDE
PERTH
Asia
HONG KONG
BEIJING
SHANGHAI
KUNSHAN
SEOUL
TOKYO
FUJISAWA
TAIPEH
MANILA
HANOI
BANGKOK
KUALA LUMPUR
SINGAPORE
JAKARTA
STANDARD PRODUCTION PROGRAMME
BASIC TYPES
OPEN
ZR
2ZR
RSR
2RSR
N
NR
K
TNG-CAGE
J-CAGE
C2
C3
1201 – 1203
1204 – 1213
1214
1215
1302 – 1303
1304 – 1311
1312
2201 – 2203
2204 – 2213
2302 – 2303
2304
2304
2305 – 2313
2314
11204 – 11212
11305 – 11310
11504 – 11510
3200B – 3218B
3301B – 3315B
3200 – 3214
3302 – 3313
3314
LB3200B – LB3207B
LZ3200B – LZ3207B
4200 – 4218
4302 – 4315
Special bearings on enquiry
Standard
on enquiry
|7
Self-aligning ball bearings
Self-aligning ball bearings are double-row bearings with a spherical outer ring raceway. The
bearings therefore facilitate angle adjustment and are suitable for compensating for angular misalignment.
Self-aligning ball bearings are manufactured with cylindrical and tapered bores. The
bearings with tapered bore are predominantly fitted to shafts with adapter sleeves.
The cages of these bearings are normally made of glass-fibre reinforced Polyamide 66.
Bearings with these cages are marked with the designation "TNG". The cages of some of
the small bearings are made of Polyamide 66 without glass-fibre reinforcement. These are
marked with the designation "TN".
A very few bearings (Version J) are mass produced with cages made of pressed steel. The
bearings which are normally fitted with plastic cages are also available on request with
cages made of pressed steel "J".
Series 22.. and 23.. self-aligning bearings are also available sealed on both sides. These
bearings are marked with the designation "2RS".
The external dimensions of self-aligning ball bearings are laid down in ISO R15 or
Standards, dimensions
DIN 630.
The bearings are only manufactured to the standard tolerance P0.
Tolerances
Self-aligning bearings with cylindrical bores are normally manufactured with standard
Bearing clearance
radial clearance C0 and those with a tapered bore with radial clearance C3. Bearings
with other clearances are available on enquiry.
The clearances can be found in the table below.
Radial bearing clearance of self-aligning ball bearings with cylindrical bore without load according to DIN 620, Part 4
Rated size
of bore (mm)
above
6
10
14
18
24
30
40
50
up to
10
14
18
24
30
40
50
65
C2
min.
2
2
3
4
5
6
6
7
max.
9
10
12
14
16
18
19
21
min.
6
6
8
10
11
13
14
16
max.
17
19
21
23
24
29
31
36
min.
12
13
15
17
19
23
25
30
max.
25
26
28
30
35
40
44
50
min.
19
21
23
25
29
34
37
45
max.
33
35
37
39
46
53
57
69
min.
27
30
32
34
40
46
50
62
max.
42
48
50
52
58
66
71
88
C0 Standard
C3
C4
C5
Bearingluftwerte
Bearing
clearances inin
µmµm
|8
Radial bearing clearance of self-aligning ball bearings with tapered bore without load according to DIN 620, Part 4
Rated size
of bore (mm)
above
18
24
30
40
50
up to
24
30
40
50
65
C2
min.
7
9
12
14
18
max.
17
20
24
27
32
min.
13
15
19
22
27
max.
26
28
35
39
47
min.
20
23
29
33
41
max.
33
39
46
52
61
min.
28
33
40
45
56
max.
42
50
59
65
80
min.
37
44
52
58
73
max.
55
62
72
79
99
C0
C3 Standard
C4
C5
Bearingluftwerte
Bearing
clearances inin
µmµm
Seals
NSK manufactures Series 22.. and 23.. self-aligning ball bearings, not only open version but also with seals on both sides of the bearing. These seals are made of nitrile
rubber and are reinforced with a steel disc embedded in the rubber. The seals are fixed
in the outer ring and seal against the inner ring with a friction sealing lip.
Sealed self-aligning ball bearings are filled with enough grease at the factory to last the
normal life span of the bearing. The bearings are therefore maintenance free. Note that
sealed self-aligning bearings have a lower load-carrying capacity than open bearings of
the same type. During installation, it is essential that they are not twisted, as otherwise
the seals may be forced out of position.
Angle adjustment facility
Self-aligning bearings facilitate angle adjustment. The permitted angle of tilt from the
central position for Series 12.. and 22.. open bearings is 2.5º and for Series 13.. and
23.. is 3º. With sealed bearings, the permitted angle of tilt is 1.5º.
Dynamic equivalent
bearing load
P = Fr + Y1 · Fa
[kN] for Fa/Fr ≤ e
P = 0.65 · Fr + Y2 · Fa
[kN] for Fa/Fr > e
The factors e, Y1 and Y2 can be found in the bearing tables.
Basic rating life
3
Lh = 1,000,000 · 1C2
n · 60
P
(Running hours)
fh = fn · 1C2
(Factors fh and fn, see tables on Page 39)
P0 = Fr + Y0 · Fa
[kN]
P
Static equivalent bearing load
The factor Y0 can be found in the bearing tables.
Basic static load rating
1 2
C0
S0 = P
0
|9
Cylindrical bore
Bore 10 – 35 mm
Dimensions
d
D
Abbreviation for
B
r1.2
cylindrical bore
Tapered bore
min
mm
10
12
15
17
20
25
30
35
Load ratings
Speed limits
dyn.
stat.
Grease
C
C0
min–1
kN
30
30
32
32
37
35
35
42
42
40
40
47
47
47
47
52
52
52
52
62
62
62
62
72
72
72
72
80
80
| 10
9
14
10
14
12
11
14
13
17
12
16
14
19
14
18
15
21
15
18
17
24
16
20
19
27
17
23
21
31
0.6
0.6
0.6
0.6
1.0
0.6
0.6
1.0
1.0
0.6
0.6
1.0
1.0
1.0
1.0
1.1
1.1
1.0
1.0
1.1
1.1
1.0
1.0
1.1
1.1
1.1
1.1
1.5
1.5
1200TN
2200TN
1201TNG
2201ETNG
1301TN
1202TNG
2202ETNG
1302TN
2302ETNG
1203TNG
2203ETNG
1303TN
2303TN
1204TNG
2204ETNG
1304TNG
2304J
1205TNG
2205ETNG
1305TNG
2305TNG
1206TNG
2206ETNG
1306TNG
2306TNG
1207TNG
2207ETNG
1307TNG
2307TNG
—
—
—
—
—
—
—
—
—
—
—
—
—
1204KTNGC3
2204EKTNGC3
1304KTNGC3
2304KJC3
1205KTNGC3
2205EKTNGC3
1305KTNGC3
2305KTNGC3
1206KTNGC3
2206EKTNGC3
1306KTNGC3
2306KTNGC3
1207KTNGC3
2207EKTNGC3
1307KTNGC3
2307KTNGC3
5.50
7.20
5.60
9.00
9.50
7.50
9.15
9.50
12.00
8.00
11.40
12.50
14.30
10.00
14.30
12.50
18.00
12.20
17.00
18.00
24.50
15.60
25.50
21.20
31.50
16.00
32.00
25.00
39.00
Oil
1.53
2.04
1.27
1.96
2.16
1.76
2.08
2.28
2.90
2.04
2.75
3.20
3.55
2.65
3.55
3.35
4.65
3.35
4.40
5.00
6.55
4.65
6.95
6.30
8.65
5.20
9.00
8.00
11.20
24,000
24,000
24,000
20,000
18,000
20,000
19,000
17,000
16,000
18,000
16,000
15,000
14,000
15,000
14,000
13,000
13,000
13,000
12,000
11,000
10,000
11,000
9,500
9,000
8,500
9,500
8,000
8,000
7,500
30,000
30,000
30,000
26,000
22,000
26,000
24,000
20,000
19,000
22,000
19,000
18,000
17,000
18,000
17,000
16,000
16,000
16,000
15,000
14,000
13,000
14,000
12,000
11,000
10,000
12,000
9,500
9,500
9,000
Tapered bore (Taper 1:12)
Factors
Abutment dimensions
da
min
mm
Da
max
14.0
14.0
16.0
16.0
17.0
19.0
19.0
20.0
20.0
21.0
21.0
22.0
22.0
25.0
25.0
26.5
26.5
30.0
30.0
31.5
31.5
35.0
35.0
36.5
36.5
41.5
41.5
43.0
43.0
26.0
26.0
28.0
28.0
32.0
31.0
31.0
37.0
37.0
36.0
36.0
42.0
42.0
42.0
42.0
45.5
45.5
47.0
47.0
55.5
55.5
57.0
57.0
65.5
65.5
65.5
65.5
72.0
72.0
ra
max
e
Weight
Y1
Fa/Fr ≤ e
Y2
Fa/fr > e
Y0
Abbreviation
<
kg
0.6
0.6
0.6
0.6
1.0
0.6
0.6
1.0
1.0
0.6
0.6
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.5
1.5
0.32
0.66
0.37
0.53
0.35
0.34
0.46
0.35
0.51
0.33
0.46
0.32
0.53
0.28
0.44
0.29
0.51
0.27
0.35
0.28
0.48
0.25
0.30
0.26
0.45
0.22
0.30
0.26
0.47
2.0
1.0
1.7
1.2
1.8
1.9
1.4
1.8
1.2
1.9
1.4
1.9
1.2
2.2
1.5
2.2
1.2
2.4
1.8
2.3
1.3
2.5
2.1
2.4
1.4
2.8
2.1
2.5
1.4
3.00
1.50
2.60
1.85
2.80
2.90
2.10
2.80
1.90
3.00
2.10
3.00
1.90
3.50
2.20
3.30
1.90
3.70
2.80
3.50
2.00
3.90
3.30
3.70
2.20
4.30
3.30
3.80
2.10
2.1
1.0
1.8
1.3
1.9
2.0
1.4
1.9
1.3
2.0
1.4
2.0
1.3
2.3
1.5
2.3
1.3
2.5
1.9
2.4
1.4
2.7
2.2
2.5
1.5
2.9
2.2
2.6
1.4
0.034
0.047
0.040
0.053
0.067
0.049
0.060
0.094
0.110
0.073
0.088
0.130
0.160
0.120
0.140
0.160
0.210
0.140
0.160
0.260
0.340
0.220
0.260
0.390
0.500
0.320
0.400
0.510
0.680
1200TN
2200TN
1201TNG
2201ETNG
1301TN
1202TNG
2202ETNG
1302TN
2302ETNG
1203TNG
2203ETNG
1303TN
2303TN
1204TNG
2204ETNG
1304TNG
2304J
1205TNG
2205ETNG
1305TNG
2305TTNG
1206TNG
2206ETNG
1306TNG
2306TNG
1207TNG
2207ETNG
1307TNG
2307TNG
| 11
Cylindrical bore
Bore 40 – 75 mm
Dimensions
d
D
Abbreviation for
B
r1.2
cylindrical bore
Tapered bore
min
mm
40
45
50
55
60
65
70
75
Load ratings
Speed limits
dyn.
stat.
Grease
C
C0
min–1
kN
80
80
90
90
85
85
100
100
90
90
110
110
100
100
120
120
110
110
130
130
120
120
140
140
125
125
150
150
130
130
160
160
| 12
18
23
23
33
19
23
25
36
20
23
27
40
21
25
29
43
22
28
31
46
23
31
33
48
24
31
35
51
25
31
37
55
1.1
1.1
1.5
1.5
1.1
1.1
1.5
1.5
1.1
1.1
2.0
2.0
1.5
1.5
2.0
2.0
1.5
1.5
2.0
2.0
1.5
1.5
2.1
2.1
1.5
1.5
2.1
2.1
1.5
1.5
2.1
2.1
1208TNG
2208ETNG
1308TNG
2308TNG
1209TNG
2209ETNG
1309TNG
2309TNG
1210TNG
2210ETNG
1310TNG
2310TNG
1211TNG
2211ETNG
1311TNG
2311TNG
1212TNG
2212ETNG
1312J
2312J
1213TNG
2213ETNG
1313J
2313J
1214TNG
2214J
1314J
2314J
1215TNG
2215J
1315J
2315J
1208KTNGC3
2208EKTNGC3
1308KTNGC3
2308KTNGC3
1209KTNGC3
2209EKTNGC3
1309KTNGC3
2309KTNGC3
1210KTNGC3
2210EKTNGC3
1310KTNGC3
2310KTNGC3
1211KTNGC3
2211EKTNGC3
1311KTNGC3
2311KTNGC3
1212KTNGC3
2212EKTNGC3
1312KJC3
2312KJC3
1213KTNGC3
2213EKTNGC3
1313KTNGC3
2313KTNGC3
—
—
—
—
1215KTNGC3
2215KJC3
1315KJC3
2315KJC3
19.30
31.50
29.00
45.00
22.00
28.00
38.00
54.00
22.80
28.00
41.50
64.00
27.00
39.00
51.00
75.00
30.00
47.50
57.50
88.50
31.00
57.00
62.50
96.50
34.50
44.00
67.50
111.00
39.00
44.50
80.00
125.00
Oil
6.55
9.50
9.65
13.40
7.35
9.00
12.90
16.30
8.15
9.50
14.30
20.00
10.00
12.70
18.00
23.60
11.60
16.60
20.80
28.30
12.50
19.30
22.90
32.50
13.70
17.10
25.10
37.50
15.60
17.80
30.00
43.00
8,500
7,500
7,000
6,700
7,500
7,000
6,300
6,000
7,000
6,700
5,600
5,300
6,300
5,600
5,000
4,800
5,600
5,300
4,800
4,300
5,300
4,500
4,300
4,000
5,000
4,500
4,000
3,600
4,800
4,300
3,800
3,400
10,000
9,000
8,500
8,000
9,000
8,500
7,500
7,000
8,500
8,000
6,700
6,300
7,500
6,700
6,000
5,600
6,700
6,300
5,600
5,300
6,300
5,300
5,300
4,800
6,000
5,600
5,000
4,300
5,600
5,300
4,500
4,300
Tapered bore (Taper 1:12)
Factors
Abutment dimensions
da
min
mm
Da
max
46.5
46.5
48.0
48.0
51.5
51.5
53.0
53.0
56.5
56.5
59.0
59.0
63.0
63.0
64.0
64.0
68.5
68.5
72.0
72.0
73.0
73.0
76.0
76.0
78.0
78.0
81.0
81.0
83.5
83.5
87.0
87.0
73.5
73.5
82.0
82.0
78.5
78.5
92.0
92.0
83.5
83.5
101.0
101.0
92.0
92.0
111.0
111.0
101.5
101.5
118.0
118.0
112.0
112.0
128.0
128.0
116.5
116.5
138.0
138.0
121.5
121.5
148.0
148.0
ra
max
e
Weight
Y1
Fa/Fr ≤ e
Y2
Fa/fr > e
Y0
Abbreviation
<
kg
1.0
1.0
1.5
1.5
1.0
1.0
1.5
1.5
1.0
1.0
2.0
2.0
1.5
1.5
2.0
2.0
1.5
1.5
2.0
2.0
1.5
1.5
2.0
2.0
1.5
1.5
2.0
2.0
1.5
1.5
2.0
2.0
0.22
0.26
0.25
0.43
0.21
0.26
0.25
0.43
0.19
0.22
0.24
0.43
0.19
0.22
0.24
0.42
0.18
0.23
0.23
0.40
0.18
0.23
0.23
0.39
0.19
0.26
0.22
0.38
0.17
0.25
0.22
0.38
2.9
2.4
2.5
1.5
3.0
2.4
2.5
1.5
3.2
2.6
2.6
1.5
3.3
2.9
2.7
1.5
3.5
2.7
2.8
1.6
3.6
2.8
2.8
1.6
3.3
2.4
2.8
1.7
3.6
2.5
2.8
1.6
4.5
3.8
3.9
2.3
4.7
3.8
3.9
2.3
4.9
4.1
4.0
2.3
5.1
4.5
4.1
2.3
5.4
4.2
4.3
2.4
5.5
4.3
4.3
2.5
5.1
3.7
4.4
2.6
5.6
3.9
4.4
2.6
3.0
2.5
2.6
1.5
3.2
2.5
2.6
1.6
3.3
3.7
2.7
1.5
3.5
2.1
2.8
1.6
3.6
2.8
2.9
1.7
3.7
2.9
2.9
1.7
3.5
2.5
3.0
1.8
3.8
2.6
3.0
1.7
0.42
0.51
0.72
0.93
0.47
0.55
0.96
1.25
0.53
0.59
1.20
1.65
0.71
0.81
1.60
2.10
0.90
1.10
1.95
2.60
1.15
1.45
2.45
3.25
1.25
1.50
3.00
4.25
1.35
1.60
3.55
5.15
1208TNG
2208ETNG
1308TNG
1208TNG
1209TNG
2209ETNG
1309TNG
2309TNG
1210TNG
2210ETNG
1310TNG
2310TNG
1211TNG
2211ETNG
1311TNG
2311TNG
1212TNG
2212ETNG
1312TNG
2312TNG
1213TNG
2213ETNG
1313J
2313J
1214TNG
2214J
1314J
2314J
1215TNG
2215J
1315J
2315J
| 13
With adapter sleeve
Shaft 17 – 50 mm
Dimensions
d1
D
Abbreviation
B
Shaft
r1.2
min
Bearing
Sleeve
mm
17
20
25
30
35
40
45
50
Load ratings
Speed limits
dyn.
stat.
Grease
C
C0
min–1
kN
47
47
52
52
52
52
62
62
62
62
72
72
72
72
80
80
80
80
90
90
85
85
100
100
90
90
110
110
100
100
120
120
| 14
14
18
15
21
15
18
17
24
16
20
19
27
17
23
21
31
18
23
23
33
19
23
25
36
20
23
27
40
21
25
29
43
1.0
1.0
1.1
1.1
1.0
1.0
1.1
1.1
1.0
1.0
1.1
1.1
1.1
1.1
1.5
1.5
1.1
1.1
1.5
1.5
1.1
1.1
1.5
1.5
1.1
1.1
2.0
2.0
1.5
1.5
2.0
2.0
1204KTNGC3
2204EKTNGC3
1304KTNGC3
2304KJC3
1205KTNGC3
2205EKTNGC3
1305KTNGC3
2305KTNGC3
1206KTNGC3
2206EKTNGC3
1306KTNGC3
2306KTNGC3
1207KTNGC3
2207EKTNGC3
1307KTNGC3
2307KTNGC3
1208KTNGC3
2208EKTNGC3
1308KTNGC3
2308KTNGC3
1209KTNGC3
2209EKTNGC3
1309KTNGC3
2309KTNGC3
1210KTNGC3
2210EKTNGC3
1310KTNGC3
2310KTNGC3
1211KTNGC3
2211EKTNGC3
1311KTNGC3
2311KTNGC3
H204
H304
H304
H2304
H205
H305
H305
H2305
H206
H306
H306
H2306
H207
H307
H307
H2307
H208
H308
H308
H2308
H209
H309
H309
H2309
H210
H310
H310
H2310
H211
H311
H311
H2311
10.00
14.30
12.50
18.00
12.20
17.00
18.00
24.50
15.60
25.50
21.20
31.50
16.00
32.00
25.00
39.00
19.30
31.50
29.00
45.00
22.00
28.00
38.00
54.00
22.90
28.00
41.50
64.00
27.00
39.00
51.00
75.00
Oil
2.65
3.55
3.35
4.65
3.35
4.40
5.00
6.55
4.65
6.95
6.30
8.65
5.20
9.00
8.00
11.20
6.55
9.50
9.65
13.40
7.35
9.00
12.90
16.30
8.15
9.50
14.30
20.00
10.00
12.70
18.00
23.60
15,000
14,000
13,000
13,000
13,000
12,000
11,000
10,000
11,000
9,500
9,000
8,500
9,500
8,000
8,000
7,500
8,500
7,500
7,000
6,700
7,500
7,000
6,300
6,000
7,000
6,700
5,600
5,300
6,300
5,600
5,000
4,800
18,000
17,000
16,000
16,000
16,000
15,000
14,000
13,000
14,000
12,000
11,000
10,000
12,000
9,500
9,500
9,000
10,000
9,000
8,500
8,000
9,000
8,500
7,500
7,000
8,500
8,000
6,700
6,300
7,500
6,700
6,000
5,600
Dimensions
d3
B1
Abutment dimensions
B2
da
db
max min
mm
32
32
32
32
38
38
38
38
45
45
45
45
52
52
52
52
58
58
58
58
65
65
65
65
70
70
70
70
75
75
75
75
Factors
Da
Ba
ra
max
min
max
e
Weight
Y1
Y2
7
7
7
7
8
8
8
8
8
8
8
8
9
9
9
9
10
10
10
10
11
11
11
11
12
12
12
12
12
12
12
12
27
27
30
28
32
32
35
34
38
39
42
40
45
44
49
45
52
50
55
51
57
56
61
57
62
61
68
63
69
68
74
69
<
Y0
Fa/Fr ≤ e Fa/fr > e
Bearing Sleeve
mm
24
28
28
31
26
29
29
35
27
31
31
38
29
35
35
43
31
36
36
46
33
39
39
50
35
42
42
55
37
45
45
59
Abbreviation
kg
23
23
23
24
28
28
28
30
33
33
33
35
38
39
39
40
43
44
44
45
48
50
50
50
53
55
55
56
60
60
60
61
42.0 5
42.0 5
45.5 8
45.5 5
47.0 5
47.0 5
55.5 6
55.5 5
57.0 5
57.0 5
65.5 6
65.5 5
65.5 5
65.5 5
72.0 7
72.0 5
73.5 6
73.5 6
82.0 6
82.0 6
78.5 6
78.5 8
92.0 6
92.0 6
83.5 6
83.5 10
101.0 6
101.0 6
92.0 7
92.0 11
111.0 7
111.0 7
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.5
1.5
1.0
1.0
1.5
1.5
1.0
1.0
1.5
1.5
1.0
1.0
2.0
2.0
1.5
1.5
2.0
2.0
0.28
0.44
0.29
0.51
0.27
0.35
0.28
0.48
0.25
0.30
0.26
0.45
0.22
0.30
0.26
0.47
0.22
0.26
0.25
0.43
0.21
0.26
0.25
0.43
0.20
0.24
0.24
0.43
0.19
0.22
0.24
0.42
2.2
1.5
2.2
1.2
2.4
1.8
2.3
1.3
2.5
2.1
2.4
1.4
2.8
2.1
2.5
1.4
2.9
2.4
2.5
1.5
3.0
2.4
2.5
1.5
3.2
2.6
2.6
1.5
3.3
2.9
2.7
1.5
3.5
2.2
3.3
1.9
3.7
2.8
3.5
2.0
3.9
3.3
3.7
2.2
4.3
3.3
3.8
2.1
4.5
3.8
3.9
2.3
4.7
3.8
3.9
2.3
4.9
4.1
4.0
2.3
5.1
4.5
4.1
2.3
2.3
1.5
2.3
1.3
2.5
1.9
2.4
1.4
2.7
2.2
2.5
1.5
2.9
2.2
2.6
1.4
3.0
2.5
2.6
1.5
3.2
2.5
2.6
1.6
3.3
2.7
2.7
1.5
3.5
2.1
2.8
1.6
0.12
0.14
0.16
0.21
0.14
0.16
0.26
0.34
0.22
0.24
0.38
0.49
0.32
0.40
0.50
0.66
0.41
0.49
0.70
0.90
0.46
0.53
0.94
1.20
0.52
0.58
1.20
1.60
0.69
0.79
1.55
2.05
0.041
0.045
0.045
0.049
0.070
0.075
0.075
0.087
0,100
0.110
0.110
0.130
0.130
0.140
0.140
0.170
0.170
0.190
0.190
0.220
0.230
0.250
0.250
0.280
0.270
0.300
0.300
0.360
0.310
0.390
0.390
0.420
1204KTNGC3
2204EKTNGC3
1304KTNGC3
2304KJC3
1205KTNGC3
2205EKTNGC3
1305KTNGC3
2305KTNGC3
1206KTNGC3
2206EKTNGC3
1306KTNGC3
2306KTNGC3
1207KTNGC3
2207EKTNGC3
1307KTNGC3
2307KTNGC3
1208KTNGC3
2208EKTNGC3
1308KTNGC3
2308KTNGC3
1209KTNGC3
2209EKTNGC3
1309KTNGC3
2309KTNGC3
1210KTNGC3
2210EKTNGC3
1310KTNGC3
2310KTNGC3
1211KTNGC3
2211EKTNGC3
1311KTNGC3
2311KTNGC3
| 15
With adapter sleeve
Shaft 55 – 65 mm
Dimensions
d1
D
Abbreviation
B
Shaft
r1.2
min
Bearing
Sleeve
mm
55
60
65
Load ratings
Speed limits
dyn.
stat.
Grease
C
C0
min–1
kN
110
110
130
130
120
120
140
140
130
130
160
160
| 16
22
28
31
46
23
31
33
48
25
31
37
55
1.5
1.5
2.0
2.0
1.5
1.5
2.1
2.1
1.5
1.5
2.1
2.1
1212KTNGC3
2212EKTNGC3
1312KJC3
2312KJC3
1213KTNGC3
2213EKTNGC3
1313KJC3
2313KJC3
1215KTNGC3
2215KJC3
1315KJC3
2315KJC3
H212
H312
H312
H2312
H213
H313
H313
H2313
H215
H315
H315
H2315
30.0
47.5
57.5
88.5
31.0
57.0
62.5
96.5
39.0
44.5
80.0
125.0
Oil
11.6
16.6
20.8
28.3
12.5
19.3
22.9
32.5
15.6
17.8
30.0
43.0
5,600
5,300
4,800
4,300
5,300
4,500
4,300
4,000
4,800
4,300
3,800
3,400
6,700
6,300
5,600
5,300
6,300
5,300
5,300
4,800
5,600
5,300
4,500
4,300
Dimensions
d3
B1
Abutment dimensions
B2
da
db
max min
mm
80
80
80
80
85
85
85
85
98
98
98
98
Factors
Da
Ba
ra
max
min
max
e
Y1
Weight
Y2
13
13
13
13
14
14
14
14
15
15
15
15
75
73
83
74
83
79
89
82
92
90
100
94
<
Y0
Bearing Sleeve
mm
38
47
47
62
40
50
50
65
43
55
55
73
Abbreviation
kg
64
65
65
66
70
70
70
72
80
80
80
82
102
102
119
119
112
112
129
129
122
122
149
149
7
9
7
7
7
9
7
7
7
13
7
7
1.5
1.5
2.0
2.0
1.5
1.5
2.0
2.0
1.5
1.5
2.0
2.0
0.18
0.23
0.23
0.40
0.18
0.23
0.23
0.39
0.17
0.25
0.22
0.38
3.5
2.7
2.8
1.6
3.6
2.8
2.8
1.6
3.6
2.5
2.8
1.6
5.4
4.2
4.3
2.4
5.5
4.3
4.3
2.5
5.6
3.9
4.4
2.6
3.6
2.8
2.9
1.7
3.7
2.9
2.9
1.7
3.8
2.6
3.0
1.7
0.90
1.10
1.95
2.60
1.15
1.45
2.45
3.25
1.35
1.60
3.55
5.15
0.35
0.39
0.39
0.49
0.40
0.46
0.46
0.55
0.71
0.83
0.83
1.05
1212KTNGC3
2212EKTNGC3
1312KJC3
2312KJC3
1213KTNGC3
2213EKTNGC3
1313KJC3
2313KJC3
1215KTNGC3
2215KJC3
1315KJC3
2315KJC3
| 17
Sealed on both sides
Bore 12 – 65 mm
Dimensions
d1
D
Abbreviation
B
Shaft
r1.2
min
Bearing
Sleeve
mm
12
15
17
20
25
30
35
40
45
50
55
60
65
Load ratings
Speed limits
dyn.
stat.
Grease
C
C0
min–1
kN
32
35
42
40
47
47
52
52
62
62
72
72
80
80
90
85
100
90
100
100
120
110
120
| 18
14
14
17
16
19
18
21
18
24
20
27
23
31
23
33
23
36
23
40
25
43
28
31
0.6
0.6
1.0
0.6
1.0
1.0
1.1
1.0
1.1
1.0
1.1
1.1
1.5
1.1
1.5
1.1
1.5
1.1
2.0
1.5
2.0
1.5
1.5
2201-2RSTNG
2202-2RSTNG
2302-2RSTN
2203-2RSTNG
2303-2RSTN
2204-2RSTNG
2304-2RSTNG
2205-2RSTNG
2305-2RSTNG
2206-2RSTNG
2306-2RSTNG
2207-2RSTNG
2307-2RSTNG
2208-2RSTNG
2308-2RSTNG
2209-2RSTNG
2309-2RSTNG
2210-2RSTNG
2310-2RSTNG
2211-2RSTNG
2311-2RSTNG
2212-2RSTNG
2213-2RSTNG
—
—
—
—
—
2204K2RSTNGC3
2304K2RSTNGC3
2205K2RSTNGC3
2305K2RSTNGC3
2206K2RSTNGC3
2306K2RSTNGC3
2207K2RSTNGC3
2307K2RSTNGC3
2208K2RSTNGC3
2308K2RSTNGC3
2209K2RSTNGC3
2309K2RSTNGC3
2210K2RSTNGC3
2310K2RSTNGC3
2211K2RSTNGC3
2311K2RSTNGC3
2212K2RSTNGC3
2213K2RSTNGC3
5.60
7.50
9.50
8.00
12.50
10.00
12.50
12.20
18.00
15.60
21.20
16.00
25.00
19.30
29.00
22.00
38.00
22.80
41.50
27.00
51.00
30.00
31.00
1.27
1.76
2.28
2.04
3.20
2.65
3.35
3.35
5.00
4.65
6.30
5.20
8.00
6.55
9.65
7.35
12.90
8.15
14.30
10.00
18.00
11.60
12.40
16,000
15,000
15,000
14,000
11,000
11,000
10,000
9,500
8,000
8,000
6,700
7,000
6,000
6,300
5,300
5,600
4,800
5,300
4,300
4,800
3,800
4,300
4,000
Factors
Abutment dimensions
da
min
mm
Da
max
16.0
19.0
20.0
21.0
22.0
25.0
26.5
30.0
31.5
35.0
36.5
41.4
43.0
46.5
48.0
51.5
53.0
56.5
59.0
63.0
66.0
68.5
74.0
28.0
31.0
37.0
36.0
42.0
42.0
45.5
47.0
55.5
57.0
65.5
65.5
72.0
73.5
82.0
78.5
92.0
83.5
101.0
92.0
109.0
101.5
111.0
ra
max
e
Weight
Y1
Fa/Fr ≤ e
Y2
Fa/fr > e
Y0
Abbreviation
<
kg
0.6
0.6
1.0
0.6
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.5
1.0
1.5
1.0
1.5
1.0
2.0
1.5
2.0
1.5
1.5
0.37
0.34
0.35
0.33
0.32
0.28
0.29
0.27
0.28
0.25
0.26
0.22
0.26
0.22
0.25
0.21
0.25
0.20
0.24
0.19
0.24
0.18
0.18
1.7
1.9
1.8
1.9
1.9
2.2
2.2
2.4
2.3
2.5
2.4
2.8
2.5
2.9
2.5
3.0
2.5
3.2
2.6
3.3
2.7
3.5
3.6
2.6
2.9
2.8
3.0
3.0
3.5
3.3
3.7
3.5
3.9
3.7
4.3
3.8
4.5
3.9
4.7
3.9
4.9
4.0
5.1
4.1
5.4
5.5
1.8
2.0
1.9
2.0
2.0
2.3
2.3
2.5
2.4
2.7
2.5
2.9
2.6
3.0
2.6
3.2
2.6
3.3
2.7
3.5
2.8
3.6
3.7
0.06
0.06
0.13
0.10
0.18
0.16
0.24
0.17
0.38
0.28
0.57
0.45
0.79
0.55
0.05
0.58
0.40
0.63
1.89
0.76
2.37
1.11
1.53
2201-2RSTNG
2202-2RSTNG
2302-2RSTN
2203-2RSTNG
2303-2RSTN
2204-2RSTNG
2304-2RSTNG
2205-2RSTNG
2305-2RSTNG
2206-2RSTNG
2306-2RSTNG
2207-2RSTNG
2307-2RSTNG
2208-2RSTNG
2308-2RSTNG
2209-2RSTNG
2309-2RSTNG
2210-2RSTNG
2310-2RSTNG
2211-2RSTNG
2311-2RSTNG
2212-2RSTNG
2213-2RSTNG
| 19
With extended inner ring
Bore 20 – 60 mm
Dimensions
d
D
Abbreviation
C
25
30
35
40
45
50
55
60
Speed limits
r1.2
dyn.
stat.
min
C
C0
mm
20
Load ratings
min–1
kN
47
52
52
62
62
72
72
80
80
90
85
100
90
110
100
110
14
15
15
17
16
19
17
21
18
23
19
25
20
27
21
22
1.0
1.0
1.0
1.0
1.0
1.0
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.5
1.5
11204TNG
11304TNG
11205TNG
11305TNG
11206TNG
11306TNG
11207TNG
11307TNG
11208TNG
11308TNG
11209TNG
11309TNG
11210TNG
11310TNG
11211TNG
11212TNG
10.0
12.5
12.2
18.0
15.6
21.2
16.0
25.0
19.3
29.0
22.0
38.0
22.8
41.5
27.0
30.0
Grease
2.65
3.20
3.35
5.00
4.65
6.30
5.20
8.00
6.55
9.65
7.35
12.90
8.15
14.30
10.00
11.60
The bore tolerances do not comply with DIN 620. The bore tolerance corresponds to the tolerance zone J7.
9,000
8,500
8,000
6,700
6,700
5,600
5,600
5,000
5,000
4,500
4,500
3,800
4,300
3,600
4,000
3,600
Die Abmaße der Bohrung stimmen nicht mit DIN 620 überein. Die Bohrungstoleranz entspricht dem Toleranzfeld
J7.
| 20
Dimensions
d2
B
Abutment dimensions Factors
Da
max
ra
max
e
Weight
Y1
Y2
Y0
mm
29.2
31.5
33.3
38.0
40.1
45.0
47.7
51.7
54.0
57.7
57.7
63.9
62.7
70.3
70.3
78.0
Abbreviation
<
kg
40
44
44
48
48
52
52
56
56
58
58
60
58
62
60
62
42.0
45.5
47.0
55.5
57.0
65.5
65.5
72.0
73.5
82.0
78.5
92.0
83.5
83.5
92.0
102.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.5
1.5
0.28
0.29
0.27
0.28
0.25
0.26
0.22
0.26
0.22
0.25
0.21
0.25
0.20
0.24
0.19
0.18
2.2
2.2
2.4
2.3
2.5
2.4
2.8
2.5
2.9
2.5
3.0
2.5
3.2
2.6
3.3
3.5
3.5
3.3
3.7
3.5
3.9
3.7
4.3
3.8
4.5
3.9
4.7
3.9
4.9
4.0
5.1
5.4
2.3
2.3
2.5
2.4
2.7
2.5
2.9
2.6
3.0
2.6
3.2
2.6
3.3
2.7
3.5
3.6
0.18
0.28
0.22
0.43
0.35
0.64
0.54
0.85
0.72
1.12
0.77
1.43
0.85
1.82
1.17
1.50
11204TNG
11304TNG
11205TNG
11305TNG
11206TNG
11306TNG
11207TNG
11307TNG
11208TNG
11308TNG
11209TNG
11309TNG
11210TNG
11310TNG
11211TNG
11212TNG
| 21
Sleeve
Shaft 20 – 50 mm
Dimensions
Shaft
dh
Abbreviation
D
B
l
d
Load ratings
Speed limits
r1.2
dyn.
stat.
Grease
min
C
C0
mm
Oil
min–1
kN
20
20
47
14
23
1.0
11504TNGC3
10.0
2.65
15,000
18,000
25
25
52
15
25
1.0
11505TNGC3
12.2
3.35
13,000
16,000
30
30
62
16
25
1.0
11506TNGC3
15.6
4.65
11,000
14,000
35
35
72
17
26
1.1
11507TNGC3
16.0
5.20
9,500
12,000
40
40
80
18
27
1.1
11508TNGC3
19.3
6.55
8,500
10,000
45
45
85
19
28
1.1
11509TNGC3
22.0
7.35
7,500
9,000
50
50
90
20
30
1.1
11510TNGC3
22.8
8.15
7,000
8,500
The
of the inner
and its 1:15
taper
do not
comply with DIN
616.
Die bore
Bohrung
des ring
Innenrings
und
deren
Kegelwinkel
1:15
stimmen
| 22
nicht mit DIN 616 überein.
Abutment dimensions
Factors
e
Weight
Y1
Fa/Fr ≤ e
Y2
Fa/fr > e
Y0
Abbreviation
<
Da
max
mm
ra
max
41.0
1.0
0.28
2.2
3.5
2.3
0.120
11504TNGC3
46.5
1.0
0.27
2.4
3.7
2.5
0.144
11505TNGC3
56.5
1.0
0.25
2.5
3.9
2.7
0.227
11506TNGC3
65.0
1.0
0.22
2.8
4.3
2.9
0.335
11507TNGC3
73.0
1.0
0.22
2.9
4.5
3.0
0.435
11508TNGC3
78.0
1.0
0.21
3.0
4.7
3.2
0.480
11509TNGC3
83.0
1.0
0.20
3.2
4.9
3.3
0.540
11510TNGC3
kg
| 23
Deep-groove ball bearings
Double-row
The structure and operation of double-row deep-groove ball bearings correspond to that
of a pair of single-row deep-groove ball bearings. They should not be used where compensation for angular misalignment is required.
Tolerances
DIN 625 double-row deep-groove ball bearings
The tolerances are stipulated in DIN 620. Double-row deep-groove ball bearings are only
manufactured to standard tolerance P0.
Bearing clearance
The bearing clearance groups are stipulated in DIN 620 Part 4 or ISO 5753 (see table).
Double-row deep-groove ball bearings are normally supplied with the standard clearance
C0 "Normal". Other clearance groups are available on enquiry.
Radial bearing clearance of single and double row deep-groove ball bearings
Rated size
Radial clearance in µm
of bore
C2
C0
d (mm)
C3
C4
C5
Standard
above
up to
min
max
min
max
min
max
min
max
min
max
–
10
18
24
30
40
50
65
80
100
120
140
160
180
200
225
250
280
315
355
10
18
24
30
40
50
65
80
100
120
140
160
180
200
225
250
280
315
355
400
0
0
0
1
1
1
1
1
1
2
2
2
2
2
4
4
4
8
8
8
7
9
10
11
11
11
15
15
18
20
23
23
25
30
32
36
39
45
50
60
2
3
5
5
6
6
8
10
12
15
18
18
20
25
28
31
36
42
50
60
13
18
20
20
20
23
28
30
36
41
48
53
61
71
82
92
97
110
120
140
8
11
13
13
15
18
23
25
30
36
41
46
53
63
73
87
97
110
120
140
23
25
28
28
33
36
43
51
58
66
81
91
102
117
132
152
162
180
200
230
14
18
20
23
28
30
38
46
53
61
71
81
91
107
120
140
152
175
200
230
29
33
36
41
46
51
61
71
84
97
114
130
147
163
187
217
237
260
290
330
20
25
28
30
40
45
55
65
75
90
105
120
135
150
–
–
–
–
–
–
37
45
48
53
64
73
90
105
120
140
160
180
200
230
–
–
–
–
–
–
| 24
DEEP-GROOVE BALL BEARINGS
Cages
Double-row, deep-groove ball bearings are normally manufactured with snap cages
made of glass-fibre reinforced Polyamide 66 and in a few cases, they are also provided
with solid brass cages.
M
solid cage made of brass, guided in the outer ring
TNG
snap cage made of glass-fibre reinforced Polyamide 66
Bearings with cages made of glass-fibre reinforced polyamide are suitable for operating temperatures up to +120ºC.
Weights
The weights shown in the dimension tables apply to the open version of the deepgroove ball bearings.
Angular adjustment facility
Because of their internal structure, double-row deep-groove ball bearings do not facilitate angular adjustment. When using these bearings, they must not be out of alignment.
Dynamic equivalent
bearing load
Basic rating life
P = Fr + Fa (Double-row deep-groove ball bearings)
With double-row deep-groove ball bearings, it is essential that Fa ≤ 0.3 · Fr
3
Lh = 1,000,000 · 1C2
n · 60
P
(Running hours)
fh = fn · C
P0 = 0.6 · Fr + 0.5 · Fa
(Single- and double-rowed deep-groove ball bearings)
P
If P0 ≈ Fr, then calculation must be with P0 = Fr.
With double-row deep-groove ball bearings, it is essential that Fa ≤ 0.3 · Fr.
C0
s0 = P
0
| 25
Deep-groove ball bearings
Double-row
Bore 10 – 90 mm
Dimensions
d
D
Abbreviation
B
rS
min
mm
10
12
15
17
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
Load ratings
Speed limits
dyn.
stat.
C
C0
14
14
14
17
16
19
18
21
18
24
20
27
23
31
23
33
23
36
23
40
25
43
28
46
31
48
31
51
31
55
33
36
40
0.6
0.6
0.6
1.0
0.6
1.0
1.0
1‚1
1.0
1.1
1.0
1.1
1.1
1.5
1.1
1.5
1.1
1.5
1.1
2.0
1.5
2.0
1.5
2.1
1.5
2.1
1.5
2.1
1.5
2.1
2.0
2.0
2.0
4200BTNG
4201BTNG
4202BTNG
4302BTNG
4203BTNG
4303BTNG
4204BTNG
4304BTNG
4205BTNG
4305BTNG
4206BTNG
4306BTNG
4207BTNG
4307BTNG
4208BTNG
4308BTNG
4209BTNG
4309BTNG
4210BTNG
4310BTNG
4211BTNG
4311BTNG
4212BTNG
4312BTNG
4213BTNG
4313BTNG
4214BTNG
4314BTNG
4215BTNG
4315BTNG
4216BTNG
4217BTNG
4218BTNG
9.15
9.30
10.4
14.6
14.6
19.6
18.0
23.2
19.3
31.5
26.0
40.0
32.0
51.0
34.0
63.0
36.0
72.0
37.5
90.0
43.0
104.0
57.0
120.0
67.0
129.0
69.5
146.0
73.5
170.0
80.0
93.0
112.0
Oil
min–1
kN
30
32
35
42
40
47
47
52
52
62
62
72
72
80
80
90
85
100
90
110
100
120
110
130
120
140
125
150
130
160
140
150
| 160
26
Grease
5.2
5.5
6.7
9.2
9.5
13.2
12.7
16.0
14.6
22.4
20.8
30.5
26.0
38.0
30.0
48.0
33.5
60.0
36.5
75.0
43.0
90.0
58.5
106.0
67.0
98.0
73.5
114.0
80.0
134.0
90.0
106.0
122.0
18,000
16,000
14,000
13,000
13,000
11,000
10,000
9,500
9,000
8,000
7,500
6,700
6,700
6,300
6,000
5,600
5,600
4,800
5,000
4,300
4,500
4,000
4,000
3,600
3,800
3,600
3,600
3,200
3,400
3,000
3,200
3,000
2,800
24,000
20,000
18,000
17,000
18,000
17,000
14,000
13,000
12,000
10,000
9,500
8,500
8,500
8,000
7,500
7,000
7,000
6,000
6,300
5,300
5,600
5,000
5,000
4,500
4,800
4,500
4,500
4,000
4,300
3,800
4,000
3,800
3,600
DEEP-GROOVE BALL BEARINGS
Weight
Abutment dimensions
da
min
Da
max
R
min
mm
14.0
16.0
19.0
20.0
21.0
22.0
25.0
26.5
30.0
31.5
35.0
36.5
41.5
43.0
46.5
48.0
51.5
53.0
56.5
59.0
63.0
64.0
68.0
71.0
73.0
76.0
78.0
81.0
83.0
86.0
89.0
94.0
99.0
Abbreviation
<
kg
26.0
28.0
31.0
37.0
36.0
42.0
42.0
45.5
47.0
55.5
57.0
65.5
65.5
72.0
73.5
82.0
78.5
92.0
83.5
101.0
92.0
111.0
102.0
119.0
112.0
129.0
117.0
139.0
122.0
149.0
131.0
141.0
151.0
0.6
0.6
0.6
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.5
1.0
1.5
1.0
1.5
1.0
2.0
1.5
2.0
1.5
2.0
1.5
2.0
1.5
2.0
1.5
2.0
2.0
2.0
2.0
0.049
0.053
0.059
0.120
0.090
0.16
0.14
0.21
0.16
0.34
0.26
0.50
0.40
0.69
0.50
0.95
0.54
1.25
0.58
1.70
0.80
2.15
1.10
2.65
1.45
3.25
1.50
3.95
1.60
5.38
2.00
2.55
3.20
4200BTNG
4201BTNG
4202BTNG
4302BTNG
4203BTNG
4303BTNG
4204BTNG
4304BTNG
4205BTNG
4305BTNG
4206BTNG
4306BTNG
4207BTNG
4307BTNG
4208BTNG
4308BTNG
4209BTNG
4309BTNG
4210BTNG
4310BTNG
4211BTNG
4311BTNG
4212BTNG
4312BTNG
4213BTNG
4313BTNG
4214BTNG
4314BTNG
4215BTNG
4315BTNG
4216BTNG
4217BTNG
4218BTNG
| 27
ANGULAR-CONTACT BALL BEARINGS
Angular-contact ball bearings
Double-row
The structure and operation of double-row, angular-contact ball bearings correspond
to that of a pair of back-to-back mounted single-row angular-contact ball bearings. They
absorb radial and axial forces in both directions. The tilting moments can also be transferred. NSK supplies double-row angular-contact ball bearings with two different contact angles. The Series 32..J and 33..J bearings have a contact angle of 32º and are
fitted with a cage made of sheet steel. These bearings have filling slots on one side.
The bearings must therefore be installed so that most of the axial force is transferred
by the side without the slots.
The Series 32.. and 33.. bearings with the suffix "BTNG" have a contact angle of 25º
and are provided with a cage made of glass-fibre reinforced Polyamide 66. These
bearings do not have filling slots and can therefore transfer axial forces in both directions.
As well as the open version, NSK supplies double-row angular-contact ball bearings
with the suffix "BTNG" also with shield or seals on one or both sides of the bearing. All
Series 32..BTNG and 33..BTNG bearings are supplied with grease as standard. The version with the cage made of sheet-steel must be used for operating temperatures above
120ºC.
The external dimensions of double-row angular-contact ball bearings comply with
DIN 628.
Tolerances
Bearing clearance
The bearings are only manufactured to standard tolerance P0.
Double-row angular-contact ball bearings do not facilitate angular adjustment.
The axial clearance of double-row angular-contact ball bearings is specified. The
bearings are mass produced with axial clearance C0 "Normal". Other clearance groups
are available on enquiry. The axial clearances can be found in the table below.
The radial clearance of Version "BTNG" is approx. 45 % of its axial clearance.
The radial clearance of Version "J" is approx. 60 % of its axial clearance.
Axial bearing clearance of double-row angular-contact ball bearings without load
Rated size
of bore (mm)
above
6
10
18
24
30
40
50
65
80
up to
10
18
24
30
40
50
65
80
100
C2
min.
1
1
2
2
2
2
3
3
3
max.
11
12
14
15
16
18
22
24
26
min.
5
6
7
8
9
11
13
15
16
max.
21
23
25
27
29
33
36
40
46
min.
12
13
16
18
21
23
26
30
35
max.
28
31
34
37
40
44
48
54
63
min.
25
27
28
30
33
36
40
46
55
max.
45
47
48
50
54
58
63
71
83
C0 Standard
C3
C4
Bearingluftwerte
µmµm
Bearing
clearances inin
| 28
Double-row
Seals
As well as the open version, NSK manufactures double-row angular-contact ball
bearings with the suffix "BTNG" also with shield or seals on one or both sides of the
bearing.
Shields ZR
Shields ZR are sheet-steel discs which are fixed inside the bearing outer ring forming a
small gap for the bearing inner ring. The bearings are available with one shield on one
side of the bearing "ZR" or shields on both sides of the bearing "2ZR".
Seals RSR
Seals RSR consist of nitrile rubber and are reinforced with a steel disc embedded in the
rubber. The seals are fixed in the outer ring and seal against the inner ring with a friction
sealing lip. The bearings are available with one seal on one side of the bearing "RSR"
or seals on both sides of the bearing "2RSR".
Lubrication
With double-row angular-contact ball bearings, the gap between the cage and the rings
is relatively small. When lubricating with grease, it is therefore not easy for the user to
introduce the grease which is required for the initial lubrication. For this reason, NSK
also supplies non-sealed double-row angular-contact ball bearings pre-filled with grease
at the factory. The grease which is supplied is a high-quality lithium-based grease with
a temperature range of –30 ºC to +120 ºC. The grease used by NSK is compatible with
all other mineral-oil-based greases.
There is no problem using oil lubrication on bearings which have been lubricated with
grease by NSK, providing that the oil used is mineral-oil based. A special version of the
bearing is necessary for use with synthetic oils or greases. In these cases, please consult NSK.
Dynamic equivalent bearing load
With Series 32..BTNG and 33..BTNG:
P = Fr + 0.92 · Fa
[kN] where Fa/Fr ≤ 0.68
P = 0.67 · Fr + 1.41 · Fa [kN] where Fa/Fr > 0.68
With Series 32..J and 33..J:
P = Fr + 0.73 · Fa
Basic rating life
3
Lh = 1,000,000 · 1C2
n · 60
P
(Running hours)
fh = fn · C
P
With Series 32..BTNG and 33..BTNG:
P0 = Fr + 0.76 · Fa
[kN]
With Series 32..J and 33..J:
P0 = Fr + 0.63 · Fa
s0 =
[kN]
C0
P0
| 29
Open
Double-row
Bore 10 – 75 mm
Dimensions
d
Abbreviation
D
B
r1.2
open
min
15
17
20
25
30
35
40
45
50
55
60
65
70
75
Speed limits
Grease
with
with
dyn.
stat.
shields
seals
C
C0
mm
10
12
Load ratings
kN
30
32
37
35
42
40
47
47
52
52
62
62
72
72
80
80
90
85
100
90
110
100
120
110
130
120
140
125
150
130
160
14.0
15.9
19.0
15.9
19.0
17.5
22.2
20.6
22.2
20.6
25.4
23.8
30.2
27.0
34.9
30.2
36.5
30.2
39.7
30.2
44.4
33.3
49.2
36.5
54.0
38.1
58.7
39.7
63.5
41.3
63.5
| 30
0.6
0.6
1.0
0.6
1.0
0.6
1.0
1.0
1.1
1.0
1.1
1.0
1.1
1.1
1.5
1.1
1.5
1.1
1.5
1.1
2.0
1.5
2.0
1.5
2.1
1.5
2.1
1.5
2.1
1.5
2.1
3200BTNG
3201BTNG
3301BTNG
3202BTNG
3302BTNG
3203BTNG
3303BTNG
3204BTNG
3304BTNG
3205BTNG
3305BTNG
3206BTNG
3306BTNG
3207BTNG
3307BTNG
3208BTNG
3308BTNG
3209BTNG
3309BTNG
3210BTNG
3310BTNG
3211BTNG
3311BTNG
3212BTNG
3312BTNG
3213BTNG
3313BTNG
3214BTNG
3314BTNG
3215BTNG
3315BTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
7.80
4.55
10.60
5.85
14.50
8.20
11.80
7.10
16.30 10.00
14.60
9.00
20.80 12.50
19.60 12.50
23.20 15.00
21.20 14.60
30.00 20.00
30.00 21.20
41.50 28.50
39.00 28.50
51.00 34.50
48.00 36.50
62.00 45.00
48.00 37.50
68.00 51.00
51.00 42.50
81.00 62.00
58.50 49.00
102.00 78.00
72.00 61.00
125.00 98.00
80.00 73.50
150.00 118.00
83.00 76.50
171.50 138.20
91.50 85.00
173.40 145.30
Oil
min–1
16000
15000
10500
14000
11000
12000
10000
10000
9000
8500
7500
7000
6300
6300
5600
5600
5000
5000
4500
4800
4000
4300
3800
3800
3400
3400
3200
3400
3000
3200
2800
22000
20000
11500
19000
16000
17000
15000
15000
13000
12000
10000
9500
8500
8500
7500
7500
6700
6700
6000
6300
5300
5600
5000
5000
4500
4500
4300
4500
4000
4300
3800
2ZR
2RSR
D1. D2
<
<
2ZR, 2RSR
Abutment dimensions
Dimensions
d1
Open
a
Weight
da
Da
ra
min
max
max
mm
Abbreviation
<
kg
17.9
18.3
21.1
23.9
25.7
30.4
15.1
16.6
19.4
15
17
19
25
27
32
0.6
0.6
1.0
0.043
0.051
0.090
3200BTNG
3201BTNG
3301BTNG
21.0
25.6
24.0
26.2
28.9
31.2
33.9
37.1
40.0
44.0
47.2
49.2
52.9
55.4
57.1
62.2
61.9
68.2
68.6
75.2
75.7
81.2
84.5
88.2
86.7
94.7
92.4
101.4
29.3
34.2
33.1
37.7
38.7
42.6
43.7
50.0
52.7
59.0
60.4
65.4
67.9
74.3
72.6
81.6
78.1
89.6
85.3
98.4
94.3
108.7
103.5
118.0
106.2
125.0
112.6
133.0
18.0
21.2
20.5
24.0
24.2
26.4
26.5
30.7
31.4
36.2
36.6
41.5
40.9
46.1
43.2
50.0
45.5
54.9
49.9
61.2
55.1
67.3
59.8
73.3
61.6
80.8
65.0
83.8
20
21
22
23
26
27
31
32
36
37
42
44
47
49
52
54
57
60
64
65
69
72
74
77
79
84
89
90
30
36
35
41
41
45
46
55
56
65
65
71
73
81
78
91
83
100
91
110
101
118
111
128
116
135
116.6
143.0
0.6
1.0
0.6
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.5
1.0
1.5
1.0
1.5
1.0
2.0
1.5
2.0
1.5
2.0
1.5
2.0
1.5
2.1
1.5
2.1
0.058
0.112
0.085
0.161
0.139
0.197
0.159
0.316
0.265
0.496
0.412
0.664
0.550
0.905
0.583
1.210
0.632
1.600
0.876
2.110
1.180
2.700
1.520
3.390
1.640
4.900
1.910
5.700
3202BTNG
3302BTNG
3203BTNG
3303BTNG
3204BTNG
3304BTNG
3205BTNG
3305BTNG
3206BTNG
3306BTNG
3207BTNG
3307BTNG
3208BTNG
3308BTNG
3209BTNG
3309BTNG
3210BTNG
3310BTNG
3211BTNG
3311BTNG
3212BTNG
3312BTNG
3213BTNG
3313BTNG
3214BTNG
3314BTNG
3215BTNG
3315BTNG
| 31
Open
Double-row
Bore 80 – 90 mm
Dimensions
d
D
Abbreviation
B
r1.2
open
min
Load ratings
Speed limits
Grease
with
with
dyn.
stat.
shields
seals
C
C0
mm
min–1
kN
80 140 44.4 2.0
85 150 49.2 2.0
90 160 52.4 2.0
| 32
3216BTNG
3217BTNG
3218BTNG
..B2ZRTNG
..B2ZRTNG
..B2ZRTNG
..B2RSRTNG
..B2RSRTNG
..B2RSRTNG
98.0
116.0
124.6
Oil
93.0
110.0
120.3
3000
2800
2600
4000
3800
3600
2ZR
2RSR
Dimensions
d1
D1. D2
<
<
a
Open
2ZR, 2RSR
Abutment dimensions
da
Da
ra
min
max
max
mm
98.5
106.4
113.2
Weight
<
Abbreviation
kg
120.3
128.5
136.6
69.0
74.6
78.9
91
100
109
129
135
141
2.0
2.0
2.1
2.450
3.300
4.170
3216BTNG
3217BTNG
3218BTNG
| 33
Double-row, with filling slot
Bore 10 – 70 mm
Main dimensions
d
D
Abbreviation
B
17
20
25
30
35
40
45
50
55
60
65
70
Speed limits
r1.2
dyn.
stat.
Lubrication
min
C
C0
Grease
mm
10
12
15
Load ratings
min–1
kN
30
32
35
42
40
47
47
52
52
62
62
72
72
80
80
90
85
100
90
110
100
120
110
130
120
140
125
150
| 34
14.0
15.9
15.9
19.0
17.5
22.2
20.6
22.2
20.6
25.4
23.8
30.2
27.0
34.9
30.2
36.5
30.2
39.7
30.2
44.4
33.3
49.2
36.5
54.0
38.1
58.7
39.7
63.5
0.6
0.6
0.6
1.0
0.6
1.0
1.0
1.1
1.0
1.1
1.0
1.1
1.1
1.5
1.1
1.5
1.1
1.5
1.1
2.0
1.5
2.0
1.5
2.1
1.5
2.1
1.5
2.1
3200J
3201J
3202J
3302J
3203J
3303J
3204J
3304J
3205J
3305J
3206J
3306J
3207J
3307J
3208J
3308J
3209J
3309J
3210J
3310J
3211J
3311J
3212J
3312J
3213J
3313J
3214J
3314J
8.0
9.5
10.8
14.5
12.6
20.7
17.2
20.8
19.0
28.9
27.2
38.1
36.8
48.5
42.0
59.8
45.4
73.1
48.2
87.6
55.7
100.5
71.4
116.1
76.4
133.7
84.2
146.9
Oil
5.9
7.1
9.0
12.3
10.8
16.7
15.3
18.5
18.5
26.7
27.3
36.5
38.0
47.5
44.8
64.8
52.1
80.9
56.0
98.3
69.9
115.3
86.1
135.3
98.4
156.4
109.5
175.5
17000
15000
13000
12000
12000
10000
10000
9500
8500
7500
7000
6300
6300
5600
5600
4800
5000
4300
4800
4000
4300
3600
3800
3400
3600
3200
3200
2800
24000
20000
18000
17000
17000
15000
15000
14000
12000
10000
9500
8500
8500
7500
7500
6300
6700
5600
6300
5300
5600
4800
5000
4500
4800
4300
4300
3800
Dimensions
d1
<
D1
a
<
Abutment dimensions
da
Da
min
max
ra
max
mm
Weight
<
Abbreviation
kg
17.2
24.4
20
14
26
0.6
0.052
3200J
19.3
26.9
22
16
28
0.6
0.063
3201J
22.6
30.4
24
19
31
0.6
0.072
3202J
24.9
34.4
27
21
36
1.0
0.132
3302J
25.5
33.8
27
21
36
0.6
0.103
3203J
27.6
40.0
31
23
41
1.0
0.192
3303J
29.5
40.5
32
26
41
1.0
0.168
3204J
32.0
43.0
34
27
45
1.0
0.230
3304J
34.6
45.1
35
31
46
1.0
0.194
3205J
38.5
52.5
40
32
55
1.0
0.369
3305J
41.2
54.0
41
36
56
1.0
0.316
3206J
45.4
61.3
47
37
65
1.0
0.585
3306J
47.8
63.3
47
42
65
1.0
0.484
3207J
50.8
69.2
54
44
71
1.5
0.816
3307J
54.0
70.4
53
47
73
1.0
0.654
3208J
59.4
80.1
59
49
81
1.5
1.070
3308J
59.8
76.4
56
52
78
1.0
0.709
3209J
66.2
89.1
64
54
91
1.5
1.400
3309J
63.7
80.8
59
57
83
1.0
0.764
3210J
72.5
96.4
73
60
100
2.0
1.950
3310J
72.0
89.7
64
64
91
1.5
1.050
3211J
80.2
106.4
80
65
110
2.0
2.550
3311J
78.2
98.3
71
69
101
1.5
1.400
3212J
86.2
115.0
86
72
118
2.0
3.250
3312J
84.7
105.8
76
74
111
1.5
1.750
3213J
92.5
123.0
94
77
128
2.0
4,100
3313J
88.7
111.5
81
79
116
1.5
1.900
3214J
98.5
131.0
101
82
138
2.0
5.050
3314J
| 35
Pulleys
Pulleys are developments of double-row angular-contact ball bearings with a reinforced
outer ring. The outer ring can be either of cylindrical or spherical design. The inner ring
of these bearings is provided with lubrication holes. The bearings have no filling slot and
absorb radial and axial forces in both directions. The contact angle of these bearings
is 25º. The bearing cage is made of glass-fibre reinforced Polyamide 66. Pulleys are
supplied with seals or shields on both sides. They are normally supplied filled with
grease at the factory. Special pulleys with galvanised bearing inner and outer rings are
also available on enquiry.
The bearings are only manufactured to the standard tolerance P0.
Tolerances
Double-row pulleys do not facilitate angular adjustment.
With double-row pulleys, the axial bearing clearance is specified. The bearings are nor-
Bearing clearance
mally supplied with axial clearance C0 "Normal". The axial clearances can be found in
the table below.
The radial clearances are approx. 45 % of the axial clearances.
Axial clearance of double-row pulleys without load
Rated size
of bore (mm)
above
6
10
18
24
30
40
50
65
up to
10
18
24
30
40
50
65
80
C0 Standard
min.
5
6
7
8
9
11
13
15
max.
21
23
25
27
29
33
36
40
Bearingluftwerte
Bearing
clearances inin
µmµm
Cages
Seals
Shields ZR
Double-row pulleys are fitted with cages made of glass-fibre reinforced Polyamide 66.
NSK manufactures pulleys with seals and shields on both sides of the bearing.
Shields are sheet-steel discs which are fixed inside the bearing outer ring forming a
small gap for the bearing inner ring. The bearings are available with shields on both
sides "2ZR".
Seals RSR
Seals RSR consist of nitrile rubber and are reinforced with a steel disc embedded in the
rubber. The seals are fixed in the outer ring and seal against the inner ring with a friction
sealing lip. The bearings are available with seals on both sides of the bearing "2RSR".
| 36
PULLEYS
Lubrication
NSK supplies pulleys filled with grease at the factory. This is a high-quality lithiumbased
grease with an admissible temperature range of –30 ºC to +110 ºC. The grease used
by NSK is compatible with all other mineral-oil-based greases. The inner rings of the
pulleys are provided with a lubrication hole so that bearings can be re-lubricated. With
Version 2RSR, the grease must be pressed in slowly to avoid damaging the seals.
Bearing load capacity
If the pulley is supported by a flat contact surface, only a small surface area of the outer
ring of the pulleys comes into contact with the rolling plane. The elastic deformation of
the outer ring reduces the load-bearing capacity of the pulley. In this case, the values
specified in the "Pulley load ratings" table must be used in the calculation.
On the other hand, when installing the pulley in a housing bore, the "Bearing load
ratings" apply which are also listed.
Suffixes
Dynamic equivalent bearing load
LZ
Pulley with cylindrical outer ring (prefix)
LB
Pulley with spherical outer ring (prefix)
B
25º Contact angle
S
Lubrication hole in inner ring
TNG
Cage made of glass-fibre reinforced Polyamide 66
2ZR
Shields on both sides
2RSR
Seals on both sides
P = Fr + 0.92 · Fa
Basic rating life
12
Lh = 1,000,000 · C
n · 60
P
3
(Running hours)
fh = fn · C
P
(Factors fh and fn see Table Page 39)
P0 = Fr + 0.76 · Fa
[kN]
s0 =
C0
P0
| 37
PULLEYS
Pulleys
LZ..2ZR
Pulleys
Bore 10 – 35 mm
Dimensions
Abbreviation
Shields
d
D*
B
Seals
rs
mm
min
10 32 14.0 0.6
LZ3200B2ZRSTNG LZ3200B2RSRSTNG
Load ratings [kN]
Speed
Bearing Pulley
limits
dyn.
stat.
dyn.
stat.
C
C0
C
C0
Weight
<
7.8
4.55
7.45
4.15
min–1
16000
10.6
5.85
9.95
5.20
15000
0.079
11.8
7.10 11.00
6.45
13000
0.100
14.6
9.00 13.80
8.30
10000
0.165
19.6 12.50 18.30 11.00
9000
0.210
21.2 14.60 19.90 13.40
8000
0.330
30.0 21.20 27.90 18.60
7100
0.500
39.0 28.50 36.2
6300
0.660
kg
0.061
LB3200B2ZRSTNG LB3200B2RSRSTNG
12 35 15.9 0.6
15 40 15.9 0.6
17 47 17.5 0.6
20 52 20.6 1.0
25 62 20.6 1.0
30 72 23.8 1.0
35 80 27.0 1.1
25.0
** with
ring D 0.05
mm
bei spherical
balligemouter
Außenring
D-0.05
LZ..2RSR
| 38
mm
LB..2ZR
LB..2RSR
Life factors fh and speed factors fn for
ball bearings
fh values for ball bearings fh =
3
Lh
Ï···
500
Lh
(h)
fh
Lh
(h)
fh
Lh
(h)
fh
Lh
(h)
fh
Lh
(h)
fh
100
110
120
130
140
0.585
0.604
0.621
0.638
0.654
400
420
440
460
480
0.928
0.944
0.958
0.973
0.986
1,500
1,600
1,700
1,800
1,900
1.440
1.470
1.500
1.530
1.560
5,000
5,500
6,000
6,500
7,000
2.150
2.220
2.290
2.350
2.410
20,000
22,000
24,000
26,000
28,000
3.420
3.530
3.630
3.730
3.830
150
160
170
180
190
0.669
0.684
0.698
0.711
0.724
500
550
600
650
700
1.000
1.030
1.060
1.090
1.120
2,000
2,200
2,400
2,600
2,800
1.590
1.640
1.690
1,730
1.780
7,500
8,000
8,500
9,000
9,500
2.470
2.520
2.570
2.620
2.670
30,000
35,000
40,000
45,000
50,000
3.910
4.120
4.310
4.480
4.640
200
220
240
260
280
0.737
0.761
0.783
0.804
0.824
750
800
850
900
950
1.140
1.170
0.190
1.220
1.240
3,000
3,200
3,400
3,600
3,800
1.820
1.860
1.890
1.930
1.970
10,000
11,000
12,000
13,000
14,000
2.710
2.800
2.880
2.960
3.040
55,000
60,000
65,000
70,000
75,000
4.790
4.930
5.070
5.190
5.310
300
320
340
360
380
0.843
0.862
0.879
0.896
0.913
1,000
1,100
1,200
1,300
1,400
1.260
1.300
1.340
1.380
1.410
4,000
4,200
4,400
4,600
4,800
2.000
2.030
2.060
2.100
2.130
15,000
16,000
17,000
18,000
19,000
3.110
3.170
3.240
3.300
3.360
80,000
85,000
90,000
95,000
100,000
5.430
5.540
5.650
5.750
5.850
fn- values for ball bearings fn =
3
331/3
ìÏ···
n
n
(min–1)
fn
n
(min–1)
fn
n
(min–1)
fn
n
(min–1)
fn
n
(min–1)
fn
10
11
12
13
14
1.490
1.450
1.410
1.370
1.340
50
55
60
65
70
0.874
0.846
0.822
0.800
0.781
300
320
340
360
380
0.481
0.471
0.461
0.452
0.444
1,500
1,600
1,700
1,800
1,900
0.281
0.275
0.270
0.265
0.260
7,500
8,000
8,500
9,000
9,500
0.1640
0.1610
0.1580
0.1550
0.1520
15
16
17
18
19
1.300
1.280
1.250
1.230
1.210
75
80
85
90
95
0.763
0.747
0.732
0.718
0.705
400
420
440
460
480
0.437
0.430
0.423
0.417
0.411
2,000
2,200
2,400
2,600
2,800
0.255
0.247
0.240
0.234
0.228
10,000
11,000
12,000
13,000
14,000
0.1490
0.1450
0.1410
0.1370
0.1340
20
22
24
26
28
1.190
1.150
1.120
1.090
1.060
100
110
120
130
140
0.693
0.672
0.652
0.635
0.620
500
550
600
650
700
0.405
0.393
0.382
0.372
0.362
3,000
3,200
3,400
3,600
3,800
0.223
0.218
0.214
0.210
0.206
16,000
18,000
20,000
22,000
24,000
0.1280
0.1230
0.1190
0.1150
0.1120
30
32
34
36
38
1.040
1.010
0.993
0.975
0.957
150
160
170
180
190
0.606
0.593
0.581
0.570
0.560
750
800
850
900
950
0.354
0.347
0.340
0.333
0.327
4,000
4,200
4,400
4,600
4,800
0.203
0.199
0.196
0.194
0.191
26,000
28,000
30,000
32,000
34,000
0.1090
0.1060
0.1040
0.1010
0.0993
40
42
44
46
48
0.941
0.926
0.912
0.898
0.886
200
220
240
260
280
0.550
0.533
0.518
0.504
0.492
1,000
1,100
1,200
1,300
1,400
0.322
0.312
0.303
0.295
0.288
5,000
5,500
6,000
6,500
7,000
0.188
0.182
0.177
0.172
0.168
36,000
38,000
40,000
45,000
50,000
0.0975
0.0957
0.0941
0.0905
0.0875
| 39
EUROPEAN SALES OFFICES AND JAPAN
SCANDINAVIA
NSK NORGE OFFICE
¯STRE KULLER¯D 5
N-3241 SANDEFJORD
TEL: +47/ 3329 3160
FAX: +47/3342 9002
E-mail: [email protected]
ITALY
NSK ITALIA S.P.A.
VIA GARIBALDI 215
20024 GARBAGNATE
MILANESE (MILAN)
TEL:+39/ 02 995 191
FAX: +39/ 02 9902 5578
GERMANY
NSK DEUTSCHLAND GMBH
HARKORTSTRASSE 15
40880 RATINGEN
TEL: +49/ 2102 4810
FAX: +49/ 2102 4812290
England
NSK UK LTD.
NORTHERN ROAD, NEWARK
NOTTINGHAMSHIRE, NG24 2JF
TEL: +44/ 1636 605123
FAX: +44/ 1636 602775
FRANCE
NSK FRANCE S.A.
QUARTIER DE LÕEUROPE
2 RUE GEORGES, GUYNEMER
78283 GUYANCOURT, CEDEX
TEL: +33/ 1 305 73939
FAX: +33/ 1 305 70001
POLAND
NSK ISKRA S.A.
SALES AND MARKETING OFFICE
UL. WARSZAWSKA 146, 25-547 KIELCE
TEL: +48/ 41 36 70 505
FAX: +48/ 41 36 70 500
TURKEY
NSK RULMANLARI ORTA DOÚU TIC. LTD. ˚TI.
YALI MAH. FEVZI CAKMAK CAD.
CAGLAR APT. NO 11/4
MALTEPE, ISTANBUL, 34844
TEL: +90/ 216 442 7106
FAX: +90/ 216 305 5505
SPAIN
NSK SPAIN, S.A.
C/ TARRAGONA, 161 CUERPO BAJO
2A PLANTA, 08014 BARCELONA
TEL: +34/ 932 89 27 63
Fax: +34/ 934 33 57 76
Japan
NSK JAPAN LTD.
NISSEI BLDF., 6-3
OHSAKI 1-CHOME SHINAGAWA-KU
TOKYO 141-8560
TEL: +81/ 3 3779 7680
FAX: +81/ 3 3779 7433
Please also visit our website: www.eu.nsk.com
All the information in this catalogue has been carefully prepared
and checked. NSK does not accept liability for incomplete
or faulty information.
© Copyright NSK 2006, Reprinting (including extracts) only permitted with the approval of NSK.
NEU/A/E/D/D/02.07 Printed in Germany.

Double-Row Ball Bearings Customised Ball Bearings

Transcription

Similar documents

Zeitschrift Kunststofftechnik Journal of Plastics