2-21 Re brochure.pages

DESIGNED
FOR THE “RIDER”
IN ALL OF US!
Simply
Transform your favorite
L
O Rinto
EM
I PofSBoots
UM
shoes
a pair
with
D3Riffs Chaps
Then BLING them up
with
leo
D3RiffsCurabitur
Custom
Jewelry
Designer Chaps
With our Custom “Side
Winders” line of Jewelry, you
can remove just one side of
the jewels. Whether you are
riding a motorcycle or a horse,
you can temporarily detach the
jewels on the “inside” of your leg
and leave on the “outside” where
it still shows off your “Bling”.
When done riding, just simply
and easily re-attach your “inside”
jewels and your all ready to go.
www.D3RIFFS.com
US & FOREIGN PATENTS PENDING
COPYRIGHT © 2014 DIAMOND DUST
DESIGN LLC.
ALL RIGHTS RESERVED. ALL TEXT,
GRAPHICS, AND PHOTOS ARE OWNED
BY DIAMOND DUST DESIGN LLC.
REPRODUCTION,
IN PART OR IN WHOLE, IN ANY FORM
WITHOUT EXPRESS WRITTEN
PERMISSION IS PROHIBITED.
1-844-D3RIFFS
#D3RIFFS
www.D3RIFFS.com
www.D3RIFFS.com
Everyone Fits in
D3Riffs
D3Riffs Chaps Extenders
custom fit your Chaps to
ANY SIZE LEG
INSTRUCTIONS
Your new chaps are made and designed to fit snugly around the ankle area. Bring the chap up your ankle a bit
to start zipping them about an inch then pull them back down over your shoe and continue to zip them closed.
There are 3 size shoe straps to accommodate different shoe styles. The leather straps will stretch so feel free to
pull them tightly around your shoe. In time your chaps conform to your body, you may not need to wear the
straps but recommended when riding. If you are wearing jeans, fold your jeans over a bit, this will help
prevent your jeans from sticking out or bunching up under the chaps. Please email us if you have any
questions at [email protected]
IN STAL LIN G YOU R J EW EL RY IS E A SY
Lay your D3RIFFS Chaps flat. Decide which Jewels you want to
wear then determine which grommet holes you need to place
the Jewelry Studs. The “Rifters” attach to 2 studs, placement at
the top front of chap (shown) OR at the bottom front of chap.
The “Side Winders” and “Satisfy Sassy” attach to 3 studs as
Common 2 point layout
Common 3 point layout
shown
IN STAL LIN G T HE J E WE LRY ST UD
Standard sizes:
SM fits up to 15 1/2 calf
MED/LG fits up to 18” calf
Add additional 1 to 6 inches
With Custom Zipper Chap
Extenders!
Try them on once and you
won’t want to wear
anything else!
www.D3RIFFS.com
Install the Custom Designed Jewelry Stud in the
corresponding grommet holes desired. Pop the stud
anchor through the back of a grommet hole. Screw the
top of the stud in through the front of the grommet hole.
use small hex wrenches (included ) to tighten securely
** Do not over tighten. Stud will still spin in grommet
Install Jewelry Stud in
grommet hole.
~Patents Pending~
Attach the Lobster claw
in it's corresponding
Jewelry Stud
Conchos are sometimes
used as center anchor
point.
Make sure Lobster Claws
are securely closed. Your
D3Riffs Chap is ready!
AT TACH IN G YO UR J E WE L RY
We recommend you attach your jewels BEFORE you put
your Chap on. Lay your jewels out flat on chap , attach it to
Jewelry Studs using the Lobster claws located on the
attachment points of jewels. Make sure Lobster claws are
properly closed.
* Side Winders have a middle Concho as attachment
point. (shown )