docVIKING SG SERIES DOUBLE PUMPS (WITH SHAFT SEAL)
download 
Report Transcription
VIKING SG SERIES DOUBLE PUMPS (WITH SHAFT SEAL)
SERIES SG-04, -05, -07 (Cast Iron) SGN-05, -07 (Ductile Iron) Section 341.2 Page 341.2.1 Issue B VIKING SG SERIES DOUBLE PUMPS (WITH SHAFT SEAL) OPERATING RANGE: SG Pumps (Cast Iron, Lip or Mechanical Sealed) Displacement Combinations No. 70 GPM 0.06 to 16 / Section M /Hr 0.011 to 3.0 / Section PSI to 500 Continuous, 2,500 Intermittent Bar to 34 Continuous, 170 Intermittent Temperature Range °F -40° to +450° °C -40° to +230° Viscosity Range SSU 28 to 1,000,000 cSt 0.1 to 250,000 Flow Range (Per Section) Pressure Range 3 SERIES SG-04/-05 SGN Pumps (Ductile Iron, Lip or Mechanical Sealed) Displacement Combinations No. 49 Flow Range GPM 0.7 to 16 / Section M /Hr 0.16 to 3.0 / Section PSI to 500 Continuous, 2,500 Intermittent Bar to 34 Continuous, 170 Intermittent Temperature Range °F -40° to +450° °C -40° to +230° Viscosity Range SSU 28 to 1,000,000 cSt 0.1 to 250,000 3 Pressure Range SERIES SG-07 VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2010 Section 341.2 Page 341.2.2 Issue B SERIES SG-04, -05, -07 (Cast Iron) SGN-05, -07 (Ductile Iron) VIKING SG SERIES DOUBLE PUMPS (WITH SHAFT SEAL) SERIES DESCRIPTION Viking SG-04, -05 and -07 Double Pumps allow two independent pumping units to be operated from a single power source to reduce equipment costs and simplify installation. System flexibility is maintained as each pumping unit can be operated at a different pressure without affecting the other. SG-10 and -14 Double Pumps are available, but not as standard product, contact factory. Standard configuration is with separate suction and discharge ports for each section. A sleeve bearing (bushing) limits fluid flow between sections, but if two separate liquids are pumped, some mixing of liquids is to be expected. Where both liquids cannot contact each other (such as reactive polyurethane foam components) custom pumps with seals between sections are available (contact factory). Optional configurations include a common suction port and separate discharge ports (to split one liquid source into two flow streams), or separate suction ports and a common discharge port (to blend two liquids). These pumps are NOT furnished with pressure relief valves as standard. Some form of overpressure protection must be provided for the system (e.g. relief valve in discharge line, torque limiting device, rupture disks, etc. MODEL NUMBER KEY SGN - 051825 - G 0 - B Spur Gear Principle Pump Size Design Series Shaft Rotation (Viewed from shaft end) 0 = Clockwise 1 = Counter Clockwise (optional) Material of Construction Blank = Cast Iron N = Ductile Iron Drive Equipment B = Foot-Bracket Mounted D = Base Mounted Direct Drive M = Face Mounted Motor Drive SERIES SG-04 AND SG-05 — 90° POSITIONING SERIES SG-07 — 180° POSITIONING Pump can be mounted in any of four 90° positions, giving the option of horizontal or vertical porting. Arrow shows direction of motor rotation as clockwise, looking from shaft end. Ports are not on shaft centerline, so inverting will result in different port locations. Clockwise pump can be mounted in either of two positions to obtain suction on right or left hand side. Offers 90° positioning with “M” drive. Ports are not on shaft centerline, so inverting will result in different port locations. VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2010 SERIES SG-04, -05, -07 (Cast Iron) SGN-05, -07 (Ductile Iron) Section 341.2 Page 341.2.3 Issue B VIKING SG SERIES DOUBLE PUMPS (WITH SHAFT SEAL) PUMP CONSTRUCTION AND FEATURES Options for different flow rates per section Anti-friction needle bearings standard for long life. Options for carbon graphite or silicon carbide bushings. Hardened steel gears and shafts for long life Combining two pumps in one eliminates an extra motor, while providing application specific solutions. Sealing options include lip seal or component mechanical seal. Mag Drive available, but not standard. Motor speed operation with options for foot mount, NEMA motor mount or IEC motor mount SEPARATE SUCTION & DISCHARGE PORTS STANDARD COMMON SUCTION, SEPARATE DISCHARGE PORTS OPTIONAL SEPARATE SUCTION, COMMON DISCHARGE PORT OPTIONAL Separate inlet and discharge ports standard to pump two liquids or use one section for scavenge, one for pumping. Option for common inlet / split discharge to split flows to two applications. Option for split inlet / common discharge to mix two liquids in constant proportions. VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2010 Section 341.2 Page 341.2.4 Issue B SERIES SG-04, -05, -07 (Cast Iron) SGN-05, -07 (Ductile Iron) VIKING SG SERIES DOUBLE PUMPS (WITH SHAFT SEAL) COMPONENT IDENTIFICATION SEPARATION PLATE & NEEDLE BEARINGS ASSEMBLY KEYS & BALLS O-RING ASSEMBLY CAPSCREWS MATCH GROUND CASING & GEARS ASSEMBLY CAPSCREWS DRIVE SHAFT DOWEL PINS HEAD & NEEDLE BEARINGS ASSEMBLY O-RING O-RING MATCH GROUND CASING & GEARS BRACKET, LIP SEAL & NEEDLE BEARINGS ASSEMBLY DOWEL PINS O-RING DRIVEN SHAFT MATERIALS OF CONSTRUCTION - ALL SERIES Standard - SG-04, -05, -07 Standard - SGN -05, -07 Options Bracket Component Cast Iron, ASTM A823 Ductile Iron, ASTM A536 Surface Hardening (Vitek) Casing Cast Iron, ASTM A823 Ductile Iron, ASTM A536 Surface Hardening (Vitek) Head, Separation Plate Cast Iron, ASTM A823 Ductile Iron, ASTM A536 Surface Hardening (Vitek) Heat Treated Steel Heat Treated Steel, ASTM A322 Bearing Steel Heat Treated Steel Heat Treated Steel, ASTM A322 Bearing Steel Journal Bearings — — — — — — Outboard Ball Bearing O-Rings Lip Seals — — — Buna-N Buna-N — — — Buna-N Buna-N — — — — — — — — — Carbon Graphite ②, High Temp Carbon Graphite, Silicon Carbide ③ Bearing Steel Neo., Viton®, PTFE, Kalrez ® Neo., Viton®, PTFE Carbon / Silicon Carbide, Silicon Carbide/Silicon Carbide — — — — — — Gears Shafts Anti-Friction Needle Bearings ① Component Mechanical Seals “B” Drive Foot Bracket “M” Drive Motor Bracket Carbon/Ni-Resist Carbon/Ni-Resist Cast Iron, ASTM A48 Cast Iron, ASTM A48 Cast Iron, ASTM A48 Cast Iron, ASTM A48 ① Needle bearings standard with lip seals. ② Carbon graphite Journal bearings standard with mechanical seals. ③ Tungsten-carbide coated shafts required with silicon carbide Journal bearings. Viton® and Kalrez® are registered trademarks of DuPont Performance Elastomers VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2010 SERIES SG-04, -05, -07 (Cast Iron) SGN-05, -07 (Ductile Iron) Section 341.2 Page 341.2.5 Issue B VIKING SG SERIES DOUBLE PUMPS (WITH SHAFT SEAL) SPECIFICATIONS ⑥ Maximum Recommended Temperature with Standard Construction: 225°F (107°C) / ⑤ Maximum Pressure: 500 PSI (34 BAR) Motor Horsepower / Kilowatts Required at 20 cSt (100 SSU) Nominal Capacity at Maximum Rated Speed 20 cSt (100 SSU) Liquid Pump Model ① Port Size (NPT) Lip Seal ⑥ Inch GPM RPM M³/Hr RPM GPM RPM M³/Hr RPM SG-041717 ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ 0.06 1750 0.01 1450 0.06 1750 0.01 1450 0.06 1750 0.01 1450 0.13 1750 0.02 1450 0.06 1750 0.01 1450 0.18 1750 0.03 1450 0.06 1750 0.01 1450 0.25 1750 0.05 1450 0.06 1750 0.01 1450 0.36 1750 0.07 1450 0.06 1750 0.01 1450 0.50 1750 0.09 1450 0.13 1750 0.02 1450 0.13 1750 0.02 1450 0.13 1750 0.02 1450 0.18 1750 0.03 1450 0.13 1750 0.02 1450 0.25 1750 0.05 1450 0.13 1750 0.02 1450 0.36 1750 0.07 1450 0.13 1750 0.02 1450 0.50 1750 0.09 1450 0.18 1750 0.03 1450 0.18 1750 0.03 1450 0.18 1750 0.03 1450 0.25 1750 0.05 1450 0.18 1750 0.03 1450 0.36 1750 0.07 1450 0.18 1750 0.03 1450 0.50 1750 0.09 1450 0.25 1750 0.05 1450 0.25 1750 0.05 1450 0.25 1750 0.05 1450 0.36 1750 0.07 1450 0.25 1750 0.05 1450 0.50 1750 0.09 1450 0.36 1750 0.07 1450 0.36 1750 0.07 1450 0.36 1750 0.07 1450 0.50 1750 0.09 1450 0.50 1750 0.09 1450 0.50 1750 0.09 1450 60 Hz Motor Speed 50 Hz Motor Speed 60 Hz Motor Speed Bracket Section SG-041718 SG-041725 SG-041735 SG-041750 SG-041770 SG-041818 SG-041825 SG-041835 SG-041850 SG-041870 SG-042525 SG-042535 SG-042550 SG-042570 SG-043535 SG-043550 SG-043570 SG-045050 SG-045070 SG-047070 Head Section 60 Hz Motor Speed HP Bracket Section Inch Lip Seal ⑥ SGN-051818 SGN-051825 SGN-051835 SGN-051850 SGN-051870 ② SGN-051810 ③ SGN-051814 SGN-052525 SGN-052535 SGN-052550 ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ GPM 0.7 0.7 0.7 0.7 0.7 0.7 0.7 1.0 1.0 1.0 RPM 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 M³/Hr 0.13 0.13 0.13 0.13 0.13 0.13 0.13 0.19 0.19 0.19 Head Section RPM 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 ① See model numbering code, page 341.2.2. ② When handling liquids with viscosities above 750 SSU (162 cSt), ½” NPT ports in the casing must be specified for the 10 section. ③ When handling liquids with viscosities above 750 SSU (162 cSt), ¾” NPT ports in the casing must be specified for the 14 section. GPM 0.7 1.0 1.4 2.0 2.8 4.0 5.6 1.0 1.4 2.0 RPM 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 M³/Hr 0.13 0.19 0.26 0.38 0.53 0.91 1.05 0.19 0.26 0.38 7 BAR HP ¼ ¼ ¼ ⅓ ⅓ ½ ¼ ⅓ ⅓ ⅓ ½ ⅓ ⅓ ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ ¾ ¾ ¾ ½ ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ 34 BAR kW kW Lb. Kg. 0.16 0.31 0.16 0.31 8.3 8.3 3.8 3.8 0.16 0.31 8.5 3.9 0.21 0.47 8.8 4.0 0.21 0.47 9.0 4.1 0.31 0.47 9.3 4.2 0.16 0.31 8.3 3.8 0.21 0.47 8.5 3.9 0.21 0.47 8.8 4.0 0.21 0.47 9.0 4.1 0.31 0.47 9.3 4.2 0.21 0.47 8.8 4.0 0.21 0.47 9.0 4.1 0.31 0.47 9.3 4.2 0.31 0.47 9.5 4.3 0.31 0.47 9.3 4.2 1 0.31 0.62 9.5 4.3 1 0.31 0.62 10.0 4.5 1 0.31 0.62 10.0 4.5 1 0.31 0.62 10.3 4.7 1 0.31 0.62 10.5 4.8 Motor Horsepower / Kilowatts Required at 20 cSt (100 SSU) 60 Hz Motor Speed 100 PSI 500 PSI RPM 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 Approximate Shipping Weight 50 Hz Motor Speed 100 PSI 500 PSI Nominal Capacity at Maximum Rated Speed 20 cSt (100 SSU) Liquid Port 60 Hz 50 Hz 60 Hz 50 Hz Size (NPT) Motor Speed Motor Speed Motor Speed Motor Speed Pump Model ① SG-051818 SG-051825 SG-051835 SG-051850 SG-051870 ② SG-051810 ③ SG-051814 SG-052525 SG-052535 SG-052550 50 Hz Motor Speed HP ¼ ¼ ¼ ⅓ ½ ½ ¾ ¼ ⅓ ⅓ 50 Hz Motor Speed 7 BAR HP ¾ ¾ 1 1 1½ 2 3 1 1 1½ Approximate Shipping Weight 34 BAR kW kW Lb. Kg. 0.16 0.16 0.16 0.21 0.31 0.31 0.47 0.16 0.21 0.21 0.47 0.47 0.62 0.62 0.93 1.24 1.86 0.62 0.62 0.93 8.3 8.5 8.8 9.0 9.3 10.0 11.0 8.8 9.0 9.3 3.8 3.9 4.0 4.1 4.2 4.5 5.0 4.0 4.1 4.2 ⑤ For maximum recommended discharge pressures when handling other viscosities and/or operating at other speeds, see performance curves at www.vikingpump.com/pumpselector. ⑥ Buna-N seals (O-Rings, shaft lip seals) standard, can be used from -40°F. to +225°F. (-40°C. to +107°C.) With sealing elements of other materials, temperatures up to +450°F. (+230°C.) can be tolerated. VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2010 Section 341.2 Page 341.2.6 Issue B SERIES SG-04, -05, -07 (Cast Iron) SGN-05, -07 (Ductile Iron) VIKING SG SERIES DOUBLE PUMPS (WITH SHAFT SEAL) SPECIFICATIONS ⑥ Maximum Recommended Temperature with Standard Construction: 225°F (107°C) / ⑤ Maximum Pressure: 500 PSI (34 BAR) Nominal Capacity at Maximum Rated Speed 20 cSt (100 SSU) Liquid Port Size 60 Hz 50 Hz 60 Hz 50 Hz (NPT) Motor Speed Motor Speed Motor Speed Motor Speed Pump Model ① Brkt. Sect. Lip Seal ⑥ SG-052570 SGN-052570 ② SG-052510 ② SGN-052510 ③ SG-052514 ③ SGN-052514 SG-053535 SGN-053535 SG-053550 SGN-053550 SG-053570 SGN-053570 ② SG-053510 ② SGN-053510 ③ SG-053514 ③ SGN-053514 SG-055050 SGN-055050 SG-055070 SGN-055070 ② SG-055010 ② SGN-055010 ③ SG-055014 ③ SGN-055014 SG-057070 SGN-057070 ② SG-057010 ② SGN-057010 ③ SG-057014 ③ SGN-057014 ② SG-051010 ② SGN-051010 ②③ SG-051014 ②③ SGN-051014 ③ SG-051414 ③ SGN-051414 SG-072929 SGN-072929 SG-072941 SGN-072941 SG-072958 SGN-072958 SG-072982 SGN-072982 ④ SG-072911 ④ SGN-072911 ④ SG-072916 ④ SGN-072916 SG-074141 SGN-074141 SG-074158 SGN-074158 SG-074182 SGN-074182 ④ SG-074111 ④ SGN-074111 ④ SG-074116 ④ SGN-074116 SG-075858 SGN-075858 SG-075882 SGN-075882 ④ SG-075811 ④ SGN-075811 ④ SG-075816 ④ SGN-075816 SG-078282 SGN-078282 ④ SG-078211 ④ SGN-078211 ④ SG-078216 ④ SGN-078216 ④ SG-071111 ④ SGN-071111 ④ SG-071116 ④ SGN-071116 ④ SG-071616 ④ SGN-071616 Inch GPM 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1.0 1.0 1.0 1.4 1.4 1.4 1.4 1.4 2.0 2.0 2.0 2.0 2.8 2.8 2.8 4.0 4.0 5.6 2.8 2.8 2.8 2.8 2.8 2.8 4.0 4.0 4.0 4.0 4.0 5.6 5.6 5.6 5.6 8.0 8.0 8.0 11.2 11.2 16.0 ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ ½ RPM 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 M³/Hr 0.19 0.19 0.19 0.26 0.26 0.26 0.26 0.26 0.38 0.38 0.38 0.38 0.53 0.53 0.53 0.75 0.75 1.05 0.53 0.53 0.53 0.53 0.53 0.53 0.75 0.75 0.75 0.75 0.75 1.05 1.05 1.05 1.05 1.50 1.50 1.50 2.10 2.10 3.00 Head Sect. RPM 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 GPM 2.8 4.0 5.6 1.4 2.0 2.8 4.0 5.6 2.0 2.8 4.0 5.6 2.8 4.0 5.6 4.0 5.6 5.6 2.8 4.0 5.6 8.0 11.2 16.0 4.0 5.6 8.0 11.2 16.0 5.6 8.0 11.2 16.0 8.0 11.2 16.0 11.2 16.0 16.0 ① See model numbering code, page 341.2.2. ② When handling liquids with viscosities above 750 SSU (162 cSt), ½” NPT ports in the casing must be specified for the 10 section. ③ When handling liquids with viscosities above 750 SSU (162 cSt), ¾” NPT ports in the casing must be specified for the 14 section. ④ When handling liquids with viscosities above 750 SSU (162 cSt) with “11” or “16” section pumps, consult factory for port recommendations. RPM 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 M³/Hr 0.53 0.75 1.05 0.26 0.38 0.53 0.75 1.05 0.38 0.53 0.75 1.05 0.53 0.75 1.05 0.75 1.05 1.05 0.53 0.75 1.05 1.50 2.10 3.00 0.75 1.05 1.50 2.10 3.00 1.05 1.50 2.10 3.00 1.50 2.10 3.00 2.10 3.00 3.00 Motor Horsepower / Kilowatts Required at 20 cSt (100 SSU) 60 Hz Motor Speed 100 PSI 500 PSI RPM 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 HP ½ ½ ¾ ⅓ ½ ½ ¾ ¾ ½ ½ ¾ ¾ ¾ ¾ 1 ¾ 1 1 1 1 1½ 1½ 1½ 2 1 1½ 1½ 1½ 2 1½ 2 2 2 2 2 3 2 3 3 50 Hz Motor Speed 7 BAR HP 1½ 2 3 1½ 1½ 1½ 2 3 1½ 2 3 3 2 3 3 3 5 5 3 3 5 5 5 7½ 3 5 5 7½ 7½ 5 5 7½ 7½ 7½ 7½ 10 10 10 15 Approximate Shipping Weight 34 BAR kW kW Lb. Kg. 0.31 0.31 0.47 0.21 0.31 0.31 0.47 0.47 0.31 0.31 0.47 0.47 0.47 0.47 0.62 0.47 0.62 0.62 0.62 0.62 0.93 0.93 0.93 1.24 0.62 0.93 0.93 0.93 1.24 0.93 1.24 1.24 1.24 1.24 1.24 1.86 1.24 1.86 1.86 0.93 1.24 1.86 0.93 0.93 0.93 1.24 1.86 0.93 1.24 1.86 1.86 1.24 1.86 1.86 1.86 3.11 3.11 1.86 1.86 3.11 3.11 3.11 4.66 1.86 3.11 3.11 4.66 4.66 3.11 3.11 4.66 4.66 4.66 4.66 6.21 6.21 6.21 9.32 9.5 10.3 11.8 9.3 9.5 10.0 10.5 11.5 10.0 10.3 10.8 11.8 100 11.0 12.0 11.5 12.8 13.8 30.8 32.0 33.5 34.5 35.8 370 33.0 34.5 35.8 37.0 38.0 36.5 37.5 38.5 39.5 38.5 39.5 40.8 40.8 41.8 43.0 4.3 4.7 5.3 4.2 4.3 4.5 4.8 5.2 4.5 4.7 4.9 5.3 4.5 5.0 5.5 5.2 5.8 6.2 14.0 14.5 15.2 15.7 16.2 16.8 15.0 15.7 16.2 16.8 17.5 16.6 17.0 17.5 17.9 17.5 17.9 18.5 18.5 19.0 19.5 ⑤ For maximum recommended discharge pressures when handling other viscosities and/or operating at other speeds, see performance curves at www.vikingpump. com/pumpselector. ⑥ Buna-N seals (O-Rings, shaft lip seals) standard, can be used from -40°F. to +225°F. (-40°C. to +107°C.) With sealing elements of other materials, temperatures up to +450°F. (+230°C.) can be tolerated. VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2010 SERIES SG-04, -05, -07 (Cast Iron) SGN-05, -07 (Ductile Iron) Section 341.2 Page 341.2.7 Issue B VIKING SG SERIES DOUBLE PUMPS (WITH SHAFT SEAL) DRIVE OPTIONS MOTOR MOUNTED UNITS (“M” DRIVE) Series SG-04, SG-05 and SG-07 external gear double pumps, in combination with a NEMA “C” flange or IEC bracket and flexible coupling, provide an easily assembled compact pumping unit. This mounting arrangement eliminates the need for on-site coupling alignment that is normally required with a basemounted unit. Dimensions for NEMA C-Flange Motor Mounted Units (“M” Drive)— See Page 341.2.10. Dimensions for IEC-Flange Motor Mounted Units (“M” Drive)— See Page 341.2.11. BASE MOUNTED UNITS (“D” DRIVE) FOOT-BRACKET MOUNTED PUMPS (“B” DRIVE) Series SG-04, SG-05 and SG-07 external gear double pumps are available mounted to a foot-bracket that is machined by Viking for an accurate fit with the pump. Dimensions for Foot-Bracket Mounted Pumps (“B” Drive)— See Page 341.2.12. Series SG-04, SG-05 and SG-07 external gear double pumps mounted to a Viking rectangular, formed steel base provides you with a solid mounting for the drive equipment and the foot-bracket mounted pump. NOTE: This mounting arrangement requires on-site coupling alignment. Dimensions for Base-Mounted Units (“D” Drive)— See Page 341.2.13. VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2010 Section 341.2 Page 341.2.8 Issue B SERIES SG-04, -05, -07 (Cast Iron) SGN-05, -07 (Ductile Iron) VIKING SG SERIES DOUBLE PUMPS (WITH SHAFT SEAL) DIMENSIONS – SERIES SG-04, SG-05, SGN-05 UNMOUNTED DOUBLE PUMPS NOTE: Dimensions in inches (millimeters) MODEL NO. SG-041717 SG-041818 SG-051818 SG-041718 SG-041725 SG-041735 SG-041750 SG-041770 SG-041825 SG-041835 SG-041850 SG-041870 SG-051825 SG-051835 SG-051850 SG-051870 SG-051810 SG-051814 SG-042525 SG-042535 SG-042550 SG-042570 SG-052525 SG-052535 SG-052550 SG-052570 SG-052510 SG-052514 SG-043535 SG-053535 B C in 3.17 3.86 mm 81 98 in 3.17 3.86 mm 81 98 in 3.24 3.93 mm 82 100 in 3.34 4.03 mm 85 102 in 3.49 4.18 mm 89 106 in 3.69 4.38 mm 94 111 in 3.99 4.68 mm 101 119 in 3.39 5.08 mm 86 129 in 3.31 4.00 mm 84 102 in 3.41 4.10 mm 87 104 in 3.56 4.25 mm 90 108 in 3.76 4.45 mm 96 113 in 4.06 4.75 mm 103 121 in 4.46 5.15 mm 113 131 in 3.51 4.20 mm 89 107 MODEL NO. SG-043550 SG-043570 SG-053550 SG-053570 SG-053510 SG-053514 SG-045050 SG-045070 SG-055050 SG-055070 SG-055010 SG-055014 SG-047070 SG-057070 SG-057010 SG-057014 SG-051010 SG-051014 SG-051414 in B C 3.66 4.35 mm 93 110 in 3.86 4.55 mm 98 116 in 4.16 4.85 mm 106 123 in 4.56 5.25 mm 116 133 in 3.81 4.50 mm 97 114 in 4.01 4.70 mm 102 119 in 4.31 5.00 mm 109 127 in 4.71 5.40 mm 120 137 in 4.21 4.90 mm 107 124 in 4.51 5.20 mm 115 132 in 4.91 5.60 mm 125 142 in 4.81 5.50 mm 122 140 in 5.21 5.90 mm 132 150 in 5.61 6.30 mm 142 160 VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2010 SERIES SG-04, -05, -07 (Cast Iron) SGN-05, -07 (Ductile Iron) Section 341.2 Page 341.2.9 Issue B VIKING SG SERIES DOUBLE PUMPS (WITH SHAFT SEAL) DIMENSIONS – SERIES SG-07, SGN-07 UNMOUNTED DOUBLE PUMPS NOTE: Dimensions in inches (millimeters) MODEL NO. SG-072929 SG-072941 SG-072958 SG-072982 SG-072911 SG-072916 SG-074141 SGN-074141 SG-074158 SGN-074158 B₁ B₂ C in 3.42 5.96 7.08 mm 87 151 180 in 3.42 6.08 7.20 mm 87 154 183 in 3.42 6.25 7.37 mm 87 159 187 in 3.42 6.49 7.61 mm 87 165 193 in 3.42 6.82 7.94 mm 87 173 202 in 3.42 7.32 8.44 mm 87 186 214 in 3.54 6.20 7.32 mm 90 157 186 in 3.54 6.37 7.49 mm 90 162 190 in 3.54 6.61 7.73 mm 90 168 196 SG-074111 SGN-074111 in 3.54 6.94 8.06 mm 90 176 205 SG-074116 SGN-074116 in 3.54 7.44 8.56 mm 90 189 217 SG-074182 SGN-074182 MODEL NO. B₁ B₂ C SG-075858 SGN-075858 in 3.71 6.54 7.66 mm 94 166 195 SG-075882 SGN-075882 in 3.71 6.78 7.90 mm 94 172 201 SG-075811 SGN-075811 in 3.71 7.11 8.23 mm 94 181 209 in 3.71 7.61 8.73 SG-075816 SGN-075816 mm 94 193 222 SG-078282 SGN-078282 in 3.95 7.02 8.14 mm 100 178 207 SG-078211 SGN-078211 in 3.95 7.35 8.47 mm 100 187 215 SG-078216 SGN-078216 in 3.95 7.85 8.97 mm 100 199 228 in 4.28 7.68 8.80 SG-071111 SGN-071111 SG-071116 SGN-071116 SG-071616 SGN-071616 mm 109 195 224 in 4.28 8.18 9.30 mm 109 208 236 in 4.78 8.68 9.80 mm 121 220 249 VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2010 Section 341.2 Page 341.2.10 Issue B SERIES SG-04, -05, -07 (Cast Iron) SGN-05, -07 (Ductile Iron) VIKING SG SERIES DOUBLE PUMPS (WITH SHAFT SEAL) DIMENSIONS – SERIES SG-04, SG-05, SGN-05 C-FLANGE MOTOR MOUNT (“M” DRIVE) – NEMA ① Drive equipment weight listed is for a typical TEFC motor, mounting bracket and couplings. (If a more accurate motor shipping weight is required, consult factory with complete motor specifications.) For total unit shipping weight, add the drive equipment shipping weight to the pump shipping weight shown on the pump specification chart. MOTOR FRAME SIZE D E F H MC MD APPROX. DRIVE ① EQUIP. SHIPPING WEIGHT IN POUNDS (KG) 56C in (mm) 3.50 (88.9) 2.44 (62.0) 1.50 (38.1) .34 (8.6) SLOT 2.56 (65.0) 3.75 (95.3) 34 (15) 143TC in (mm) 3.50 (88.9) 2.75 (69.9) 2.00 (50.8) .34 (8.6) 2.88 (73.2) 3.75 (95.3) 52 (24) 57 (26) 145TC in (mm) 3.50 (88.9) 2.75 (69.9) 2.50 (63.5) .34 (8.6) 2.88 (73.2) 3.75 (95.3) 182TC in (mm) 4.50 (114.3) 3.75 (95.3) 2.25 (57.15) .41 (10.4) 3.62 (92.0) 4.25 (108.0) 83 (38) 184TC in (mm) 4.50 (114.3) 3.75 (95.3) 2.75 (69.9) .41 (10.4) 3.62 (92.0) 4.25 (108.0) 88 (40) DIMENSIONS – SERIES SG-07, SGN-07 – C-FLANGE MOTOR MOUNT (“M” DRIVE) – NEMA ① Drive equipment weight listed is for a typical TEFC motor, mounting bracket and couplings. (If a more accurate motor shipping weight is required, consult factory with complete motor specifications.) For total unit shipping weight, add the drive equipment shipping weight to the pump shipping weight shown on the pump specification chart. MOTOR FRAME SIZE D E F H MC MD APPROX. DRIVE ① EQUIP. SHIPPING WEIGHT IN POUNDS (KG) 56C in (mm) 3.50 (88.9) 2.44 (62.0) 1.50 (38.1) .34 (8.6) SLOT 2.56 (65.0) 4.88 (124.0) 41 (19) 143TC in (mm) 3.50 (88.9) 2.75 (69.9) 2.00 (50.8) .34 (8.6) 2.88 (73.2) 4.88 (124.0) 60 (27) 145TC in (mm) 3.50 (88.9) 2.75 (69.9) 2.50 (63.5) .34 (8.6) 2.88 (73.2) 4.88 (124.0) 70 (32) 182TC in (mm) 4.50 (114.3) 3.75 (95.3) 2.25 (57.15) .41 (10.4) 3.62 (92.0) 5.37 (136.4) 108 (49) 184TC in (mm) 4.50 (114.3) 3.75 (95.3) 2.75 (69.9) .41 (10.4) 3.62 (92.0) 5.37 (136.4) 123 (56) 213TC in (mm) 5.25 (133.4) 4.25 (108.0) 2.75 (69.9) .41 (10.4) 4.50 (114.3) 6.26 (159.0) 161 (73) 215TC in (mm) 5.25 (133.4) 4.25 (108.0) 3.50 (88.9) .41 (10.4) 4.50 (114.3) 6.26 (159.0) 195 (88) VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2010 SERIES SG-04, -05, -07 (Cast Iron) SGN-05, -07 (Ductile Iron) Section 341.2 Page 341.2.11 Issue B VIKING SG SERIES DOUBLE PUMPS (WITH SHAFT SEAL) DIMENSIONS – SERIES SG-04, SG-05, SGN-05 – MOTOR MOUNT – (“M” DRIVE) – IEC FRAME MOTOR FRAME IEC 80 B35 FLANGE IEC 90 B35 FLANGE in (mm) in (mm) F G H MC MD APPROX. DRIVE ① EQUIP. SHIPPING WEIGHT IN POUNDS (KG) 2.46 (62.5) 1.97 (50) 3.94 (100) 0.39 (10) 1.97 (50) 3.73 (94.7) 46 (21) 2.76 (70) S 1.97 (50) / L 2.46 (62.5) 3.94 (100) 0.39 (10) 2.20 (56) 3.73 (94.7) 64 (29) D E 3.15 (80) 3.54 (90) ① Motor shipping weight listed is for a typical IEC motor. (If a more accurate motor shipping weight is required, consult factory with complete motor specifications.) For total unit shipping weight, add the electric motor shipping weight to the pump shipping weight shown on the pump specification chart. DIMENSIONS – SERIES SG-07, SGN-07 – MOTOR MOUNT (“M” DRIVE) – IEC FRAME MOTOR FRAME IEC 90 B35 FLANGE in (mm) D E F G H MC MD APPROX. DRIVE ① EQUIP. SHIPPING WEIGHT IN POUNDS (KG) 3.54 (90) 2.76 (70) S 1.97 (50) / L 2.46 (62.5) 3.94 (100) 0.39 (10) 2.20 (56) 5.13 (130.3) 68 (31) --- 0.47 (12) 2.48 (63) 5.26 (133.6) 114 (52) --- 0.47 (12) 2.76 (70) 5.26 (133.6) 129 (59) IEC 100 B14 FACE in (mm) 3.94 (100) 3.15 (80) S 2.20 (56) / L 2.76 (70) IEC 112 B14 FACE in (mm) 4.41 (112) 3.74 (95) S 2.24 (57) / L 2.76 (70) ① Motor shipping weight listed is for a typical IEC motor. (If a more accurate motor shipping weight is required, consult factory with complete motor specifications.) For total unit shipping weight, add the electric motor shipping weight to the pump shipping weight shown on the pump specification chart. VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2010 Section 341.2 Page 341.2.12 Issue B SERIES SG-04, -05, -07 (Cast Iron) SGN-05, -07 (Ductile Iron) VIKING SG SERIES DOUBLE PUMPS (WITH SHAFT SEAL) DIMENSIONS – SERIES SG-04, SG-05, SGN-05 FOOT BRACKET MOUNT (“B” DRIVE) NOTE: Approximate shipping weight of foot bracket is 2¼ lbs. (0.9 kg) NOTE: Dimensions in inches (millimeters). NOTE: Bracket part number is 2-070-012-100-00 NOTE: Shaft height corresponds to Viking’s “A” reducer or NEMA 56, 143T and 145T motors. DIMENSIONS – SERIES SG-07, SGN-07 – FOOT BRACKET MOUNT (“B” DRIVE) NOTE: Approximate shipping weight of foot bracket is 5 lbs. (1.9 kg) NOTE: Dimensions in inches (millimeters). NOTE: Bracket part number is 2-070-200-100-00. NOTE: Shaft height corresponds to NEMA 182T and 184T motors. VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2010 SERIES SG-04, -05, -07 (Cast Iron) SGN-05, -07 (Ductile Iron) Section 341.2 Page 341.2.13 Issue B VIKING SG SERIES DOUBLE PUMPS (WITH SHAFT SEAL) DIMENSIONS – SERIES SG-04, SG-05, SGN-05 BASE-MOUNTED UNIT (“D” DRIVE) NOTE: Dimensions in inches (millimeters). MOTOR FRAME SIZE D 56 143T 145T 182T 184T in 3.50 mm 89 in 3.50 mm 89 in 3.50 mm 89 in 4.50 mm 114 in 4.50 mm 114 APPROX. MOTOR ① SHIPPING WEIGHT IN POUNDS (KG) APPROX. DRIVE ② EQUIP. SHIPPING WEIGHT IN POUNDS (KG) 31 (14) 17 (8) 50 (23) 17 (8) 60 (27) 17 (8) 95 (43) 20 (9) 110 (50) 20 (9) ① Motor shipping weight listed is for a typical TEFC motor. (If a more accurate motor shipping weight is required, consult factory with complete motor specifications.) ② Drive equipment shipping weight includes base, foot-bracket, coupling and coupling guard. For total unit shipping weight, add electric motor shipping weight, drive equipment shipping weight and the pump shipping weight shown on the pump specification chart. DIMENSIONS – SERIES SG-07, SGN-07 BASE-MOUNTED UNIT (“D” DRIVE) NOTE: Dimensions in inches (millimeters). MOTOR FRAME SIZE 56 143T 145T D E F G H J K in 4.50 8.50 20.50 1.50 .50 .75 .75 (mm) (114) (216) (520) (190) (13) (19) (19) APPROX. MOTOR ① SHIPPING WEIGHT IN POUNDS (KG) APPROX. DRIVE ② EQUIP. SHIPPING WEIGHT IN POUNDS (KG) 31 (14) 50 (23) 38 (17) 60 (27) 182T in 4.50 9.00 25.00 2.94 .56 1.50 1.00 95 (43) 184T (mm) (114) (229) (635) (75) (14) (38) (25) 110 (50) 213T in 5.25 9.00 25.00 2.94 .56 1.50 1.00 145 (66) 215T (mm) (133) (229) (635) (75) (14) (38) (25) 179 (81) 49 (22) 56 (25) ① Motor shipping weight listed is for a typical TEFC motor. (If a more accurate motor shipping weight is required, consult factory with complete motor specifications.) ② Drive equipment shipping weight includes base, foot-bracket, coupling and coupling guard. For total unit shipping weight, add electric motor shipping weight, drive equipment shipping weight and the pump shipping weight shown on the pump specification chart. VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2010 SERIES SG-04, -05, -07 (Cast Iron) SGN-05, -07 (Ductile Iron) Section 341.2 Page 341.2.14 Issue B VIKING SG SERIES DOUBLE PUMPS (WITH SHAFT SEAL) PERFORMANCE CURVE NOTES Printed performance curves are not available. Performance curves for individual pump sections can be electronically generated with the Viking Pump Selector Program. This program can be located on www.vikingpump.com/pumpselector for the general public. For authorized distributors, this program can be found listed under the “Products” tab at www.idexconnect.com. Security passwords are required to access IDEXconnect. VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2010
Similar documents
M03 Series - Hydra
at minimum and maximum pump speed to ensure the correct hp or kW
motor is selected. Note that motor manufacturers typically de-rate the
service factor to 1.0 when operating with a VFD.
Centrifugal Pump Performance Curves and Technical Information
the individual pump curve where the vertical line from the
desired flow rate intersects the NPSH curve. From this point,
a horizontal line to the right will intersect the NPSH scale at
the net posi...