fuel system parts

Transcription

fuel system parts
Fuel/Carb Section (C)
Version 01 March/05
FUEL SYSTEM PARTS
MANUAL PETCOCK TO REPLACE VACUUM
TYPES USED ON 78-84 XS650's
Petcocks - Non Vacuum type to replace 78-84 vacuum type petcocks.
All 1978-84 North American market 650's have original petcocks operated by
Vacuum from a line to the intake (on carb holder). 1978-79 models have 2 and
1980-84 models have 1 petcock. Vacuum petcocks are chronic leakers and
are all getting to the point of being non-repairable. Our petcock is the Early
type 650 manual petcock with a wider flange cast on it so it will fit in place of
the vacuum types. Our Petcock fits to right or left and each comes with the tap
to tank O-Ring seal and assorted outlet fittings ( petcock has 2 outlet ports).
Fittings included: 2 ninety degree, 1 Straight fitting & 1 outlet port Plug. There
is an "ON", "OFF and "Reserve" position. XS# 20-0019 .... $40.00 each
BLIND PLUG
Blind Plug - Carb Holder Air Barb OEM Ref. # 1J7-13569-00
Fits: XS650 stock carb holders & blocks
off air barbs when vacuum petcocks are
replaced with manual type petcocks.
Order quantity needed.
XS# 48-1447 ...... $1.50ea.
SEALING WASHERS &
PETCOCK MOUNT SCREWS
Tap to Tank sealing Washers and
Mount Screws. Fits All 650's 70-84
XS# 20-0020 ..... $1.50/set
OUTLET FITTINGS
Petcock 90 degree outlet fitting
Replacement fittings - Fits:XS 650
Petcocks #20-0019/0050/0051
XS# 20-6420 ..... $3.00ea.
PETCOCK FILTER SET
Petcock Fuel Pipe Filter Set (2)
Filter set - Replacements for #20-0019
petcocks and will also fit 1970-77 stock
petcocks XS# 20-6419 .. $2.00/pk/2.
48
FUEL SYSTEM PARTS
Fuel/Carb Section (C)
Version 01 March/05
PETCOCK - MANUAL TYPE
Petcock - Original Non Vacuum
Manual type - (3 screw rear
cover)
Includes Tap to Tank O-Ring.
Will replace all original non-Vacuum
types used on 1970-77 650's.
<<< Petcock - LH - XS# 20-0050
$38.00 each
Petcock - RH - XS# 20-0051 >>>
PETCOCK MOUNT O-RING
Tap to Tank O-Ring - Fits: Petcocks on
70-77 650's XS# 20-0015 .... $4.00ea.
PETCOCK REAR GASKET
Petcock Rear Cover Gasket - (3 Hole)
OEM# 447-24522-00 Fits: TX/XS650's SEALING WASHERS
1973-77 + our #20-0019 petcocks.
Tap to Tank sealing Washers.
XS# 20-0053 .... $5.00ea.
Fit under mount screws on 70-84 650's
XS# 20-0018 ..... $0.50/pr.
PETCOCK REBUILD KIT
Petcock Rebuild kit - Fits: TX650/A 73-74, XS650B/C/D
75-77. These petcocks have a 3 screw rear cover plate.Kit contains:
1pc. Valve Rubber, 1pc. Wave Washer, 1pc. Tap to tank O-Ring,
2pc. Tank bolt Washer, 1pc. Drain screw Gasket, 1 pc. Rear cover
Gasket ( 3 Screw ).
XS# 20-0014 ...... $15.00/kit
49
PETCOCK REAR GASKET
Petcock Rear Cover Gasket - (2 Hole)
OEM Ref.# 256-24522-00
Fits: TX/XS650's (usually on 1970-72).
XS# 20-0052 .... $5.00ea.
PETCOCK REBUILD KIT
Petcock Rebuild kit - Fits: XS1/XS1B/XS2 70-72 These
petcocks have a 2 screw rear cover plate. Kit contains:
1pc. Valve Rubber, 1pc. Wave Washer, 1pc. Tap to tank O-Ring,
2pc. Tank bolt Washer, 1pc. Drain screw Gasket, 1 pc.Rear
cover Gasket ( 2 Screw) XS# 20-0049 ..$15.00/kit
Fuel/Carb Section (C)
Version 01 March/05
FUEL SYSTEM PARTS
GAS CAP WITH KEYS
GAS CAP WITH KEYS
Gas Cap - Fits: XS650 "Standard" models 1976-79
XS# 20-0033 .... $30.00ea. OEM Ref.# 584-26402-00
Gas Cap - Fits: XS650 "Special" models 1978-84
XS# 20-0034 .... $34.00ea. OEM Ref.# 2M0/4R0-24600
GAS CAP SEAL
GAS CAP SEAL
Gas cap rubber Seal - Fits: All 1976-84 XS650 gas caps.
XS# 20-0036 ..... $4.00ea.
Gas cap Seal - Fits: All 1974-75 XS/TX 650 gas caps.
Oem Ref.# 341-24612-01 XS# 20-0038 ... $8.00ea.
FUEL TAP to TANK O-RING
Fits: Stock Vacuum Petcocks on 78E Standard model Only!
XS# 20-0017 ..... 4.00ea.
FUEL TAP MOUNT O-RING
Tap to Tank O-Ring- Fits: Stock Vacuum Petcock on XS650
78-84 models Except 78E Std. XS # 20-0016 .. $2.00ea.
PETCOCK MOUNT O-RING
Tap to Tank O-Ring - Fits: Petcocks on
70-77 650's XS# 20-0015 .... $4.00ea.
INLINE FUEL FILTER
Clear square inline Fuel Filter XS# 20-0013 .. $2.00ea.
50
CARB PARTS
BRASS CARB FLOAT
Fuel/Carb Section (C)
Version 01 March/05
CARB FLOAT
Brass Carb Float - Fits: 70-79 XS Stock 38mm. CV Carbs
Oem Ref.# 256-14985-00 XS# 20-6500 .... $12.00ea.
Plastic Carb Float - Fits: 80-84 XS Stock 34mm.CV Carbs
Oem Ref.# 3H5-14985-00 XS# 20-6502 .... $12.00ea.
also replaces Brass float used on early 1980 650 specials
FLOAT BOWL GASKET
FLOAT BOWL GASKET
Gasket - Float Bowl - Fits: 80-84 Stock 34mm XS CV Carbs
Oem Ref.# 3F7-14984-00 XS# 20-5020 .... $4.00ea.
Gasket - Float Bowl - Fits: 70-79 Stock 38mm. CV Carbs
Oem Ref.# 256-14984-00 XS# 20-7029 .... $4.00ea.
FLOAT BOWL DRAIN PLUG
FLOAT BOWL DRAIN SCREW
Float Bowl Drain Plug - Fits:70-79 Stock 38mm. CV Carbs.
XS# 48-0779 .... $3.00ea.
Float Bowl Drain Screw with O-Ring - Fits:80-84 XS Stock
34mm. CV Carbs.
XS# 48-0778 .... $4.00ea.
FUEL LINE
BRASS FUEL LINE T
T-Piece - ( Fuel supply T pipe that fits between carbs )
Fits: 80-84 34mm. CV carbs. XS# 48-0884 .... $15.00ea.
Black Rubber Fuel Line - (original thin wall type) 1/4" ID
(6mm.) - 1pc. x 11.5"
XS# 20-4010 ..... $1.00/pc.
51
CARB PARTS
Fuel/Carb Section (C)
Version 01 March/05
CARB CHOKE PLUNGER
CARB CHOKE PLUNGER
Carb Choke Plunger - Fits: 1980-84 stock Carb Choke Plunger - Fits: XS1/XS1B
CV Carbs. XS# 48-0775 ..... $12.00ea. (1970-71) OEM Ref.# 603-14171-00
XS# 48-2009 ..... $8.00ea.
CARB CHOKE PLUNGER
Carb Choke Plunger - Fits: Stock
BS38 CV Carbs as on XS2/TX650/
TX650A/XS650B (1972-75 Only! )
XS# 48-2002 ...... $8.00ea.
CARB CHOKE PLUNGER
Carb Choke Plunger - Fits: XS650C/
D/E/SE/F/2F/SF (1976-79)
XS# 48-2012 ..... $8.00ea.
48-5040
48-5041
CHOKE PLUNGER SEAL
- Carb Choke Plunger Dust Seal XS# 48-5040 Fits: 80-84 650's .... $2.00ea.
XS# 48-5041 Fits: 70-79 650's .... $2.00ea.
CARB CHOKE PLUNGER
Carb Choke Plunger - Mikuni VM18/144
type - Fits: Mikuni Round slide VM 30- 44mm.
carbs with lever type (vertical pull) choke
plunger. XS# 48-2005 .... $8.00ea.
CARB CHOKE BODY GASKET
7 Hole - XS# 48-2010 ... $2.00ea. - Fits: TX650A, XS650B (74-75)
8 Hole - XS# 48-2011 .... $2.00ea. - Fits: XS650XS650C/D/E/F/2F/SF (76-79)
Note: 1970-73 models do not use a choke body gasket.
52
CARB PARTS
FLOAT VALVE
Float Valve - 10mm. Threaded type Fits: XS1/XS1B (1970-71)
XS# 48-1429 .. $8.00ea.
FLOAT VALVE
Carb Float Valve - threaded type Fits:
XS2 (72), TX650/A (73-74), XS650B-F
(75-79) XS# 48-5019 .... $8.00ea.
Fuel/Carb Section (C)
Version 01 March/05
FLOAT VALVE
Carb Float Valve - Push in with O-Ring
seal, needle & clip. Fits: Stock CV carbs
XS650G-K (1980-84) Specials.
XS# 48-1445 .... $10.00ea.
FLOAT NEEDLE
SEAL -THROTTLE SHAFT
Float Needle with clip - Fits: XS650G-K
(80-84) 34mm. CV Carbs - Viton tipped
Needle Only XS# 48-5014 .. $4.00ea.
Seal - Throttle butterfly shaft Fits: 1970-79 XS BS38 CV Carbs.
XS# 48-5021 ..... $5.00ea.
CV CARB
SLIDE/DIAPHRAGM ASSEMBLY
CV CARB
SLIDE/DIAPHRAGM ASSEMBLY
Carb Slide & Diaphragm Assy. - Fits: Mikuni BS38 CV Carbs
as used on 1970-77 XS/TX 650's OEM# 256-14940
Mikuni Genuine XS# 20-6029 .... $69.00ea.
Carb Slide & Diaphragm Assy. - Fits: Mikuni BS34 CV Carbs
as used on 1980-84 XS650's OEM# 3F7/3H5-14940
Mikuni Genuine XS# 20-6028 .... $64.00ea.
Notes: Carb slides for 1978-79 XS650's are Not interchangeable with other slides as the needle retainer differs.
Slides should be replaced if the diaphragms are torn or if the slide body rotates from the diaphragm (is loosened).
53
CARB JETS
Fuel/Carb Section (C)
Version 01 March/05
Jets Sold in multiples
48-0100 Series $ 6.00Pr.
Main Jet - Large Round Type - N100/604 Mikuni - of 2pc. each size Only
Fits: Most 80-84 Stock XS650 Mikuni 34mm. CV carbs - Main Jet OEM # 620-1423148-0111
#115 Main Jet - Large Round Type - N100/604 Mikuni
48-0113
#120 Main Jet - Large Round Type - N100/604 Mikuni
48-0115
#125 Main Jet - Large Round Type - N100/604 Mikuni
48-0116
#127.5 Main Jet - Large Round Type - N100/604 Mikuni
48-0117
#130 Main Jet - Large Round Type - N100/604 Mikuni
48-0118
#132.5 Main Jet - Large Round Type - N100/604 Mikuni
Main Jet
48-0119
#135 Main Jet - Large Round Type - N100/604 Mikuni
- Large Round Type
48-0120
#137.5 Main Jet - Large Round Type - N100/604 Mikuni
- N100/604 Mikuni
48-0121
#140 Main Jet - Large Round Type - N100/604 Mikuni
Note: Average Standard size for
48-0122
#142.5 Main Jet - Large Round Type - N100/604 Mikuni
XS650
G/SG/H/SH/SJ/SK/SL (80-84)
48-0123
#145 Main Jet - Large Round Type - N100/604 Mikuni
is #132.5
48-0124
#147.5 Main Jet - Large Round Type - N100/604 Mikuni
48-0125
#150 Main Jet - Large Round Type - N100/604 Mikuni
48-0126
#152.5 Main Jet - Large Round Type - N100/604 Mikuni
48-0127
#155 Main Jet - Large Round Type - N100/604 Mikuni
48-0128
#157.5 Main Jet - Large Round Type - N100/604 Mikuni
48-0129
#160 Main Jet - Large Round Type - N100/604 Mikuni
Main Jet Washer - Fits: 1980-84 CV carbs
(Fits under main Jet ) XS# 48-0199 .. $1.00ea.
48-0200 Series $ 6.00Pr.
Main Jet - Small Round Type - N102/221
Fits: All 1970-79 XS/TX650 Mikuni BS38 CV carbs - Jet # 256-14944 also used as the Air Jet on all 1980-84 XS650G-K 34mm. OEM Mikuni CV carbs.
XS# 48-0206 #115 Main Jet - Small Round Type - N102/221 Mikuni
XS# 48-0208 #120 Main Jet - Small Round Type - N102/221 Mikuni
XS# 48-0209 #122.5 Main Jet - Small Round Type - N102/221 Mikuni
XS# 48-0210 #125 Main Jet - Small Round Type - N102/221 Mikuni
XS# 48-0211 #127.5 Main Jet - Small Round Type - N102/221 Mikuni
XS# 48-0212 #130 Main Jet - Small Round Type - N102/221 Mikuni
Main Jet
XS# 48-0213 #132.5 Main Jet - Small Round Type - N102/221 Mikuni
- Small Round Type XS# 48-0214 #135 Main Jet - Small Round Type - N102/221 Mikuni
N102/221 Mikuni
XS# 48-0215 #137.5 Main Jet - Small Round Type - N102/221 Mikuni
XS# 48-0216 #140 Main Jet - Small Round Type - N102/221 Mikuni
XS# 48-0217 #142.5 Main Jet - Small Round Type - N102/221 Mikuni
XS# 48-0218 #145 Main Jet - Small Round Type - N102/221 Mikuni
XS# 48-0219 #147.5 Main Jet - Small Round Type - N102/221 Mikuni
XS# 48-0220 #150 Main Jet - Small Round Type - N102/221 Mikuni
XS# 48-0221 #152.5 Main Jet - Small Round Type - N102/221 Mikuni
XS# 48-0222 #155 Main Jet - Small Round Type - N102/221 Mikuni
XS# 48-0223 #157.5 Main Jet - Small Round Type - N102/221 Mikuni
XS# 48-0224 #160 Main Jet - Small Round Type - N102/221 Mikuni
Main Jet average Standard Sizes for 70-79 XS/TX650 - Stock 38mm. CV Carbs
#130
#127.5
#122.5
#135
- XS1/XS1B/XS2/TX650 (1970-73)
- TX650A/XS650B (1974-75)
- XS650C/D (1976-77)
- XS650E/SE/F/SF/2F (1978-79)
54
Air Jet for 1980-84 XS650 Stock CV Carbs
Standard Size is #135 (N102/221 Type)
CARB JETS
48-0300 Series $ 6.00Pr.
48-0313
48-0314
48-0315
48-0316
48-0317
48-0318
48-0319
48-0320
48-0321
48-0322
48-0323
48-0324
48-0325
48-0326
48-0327
48-0328
#150
#155
#160
#165
#170
#175
#180
#185
#190
#195
#200
#210
#220
#230
#240
#250
Main Jet - Large Hex Type - 4/042 Mikuni Fits: All Mikuni VM roundslide aftermarket carbs and most Mikuni TM Flatslide Carbs.
Main Jet - Large Hex Type - 4/042 Mikuni
Main Jet - Large Hex Type - 4/042 Mikuni
Jets Sold in multiMain Jet - Large Hex Type - 4/042 Mikuni
ples
Main Jet - Large Hex Type - 4/042 Mikuni
Main Jet - Large Hex Type - 4/042 Mikuni
Main Jet - Large Hex Type - 4/042 Mikuni
Main Jet - Large Hex Type - 4/042 Mikuni
Main Jet - Large Hex Type - 4/042 Mikuni
Main Jet - Large Hex Type - 4/042 Mikuni
Main Jet - Large Hex Type - 4/042 Mikuni
Main Jet - Large Hex Type - 4/042 Mikuni
Main Jet - Large Hex Type - 4/042 Mikuni
Main Jet - Large Hex Type - 4/042 Mikuni
Main Jet
Main Jet - Large Hex Type - 4/042 Mikuni
- Large Hex Type Main Jet - Large Hex Type - 4/042 Mikuni
4/042 Mikuni Main Jet - Large Hex Type - 4/042 Mikuni
48-0500 Series $ 6.00Pr.
48-0501
48-0502
48-0503
48-0504
48-0505
48-0506
48-0507
48-0508
48-0509
48-0510
48-0511
Fuel/Carb Section (C)
Version 01 March/05
Pilot Jet - VM22/210 Mikuni Type Fits: BS 38 CV carbs on XS650's C-F (76-79) and Aftermarket Mikuni VM roundslide carbs
+ most TM Flatslide carbs.
#15
Pilot Jet - VM22/210 Mikuni Type
#17.5 Pilot Jet - VM22/210 Mikuni Type
#20
Pilot Jet - VM22/210 Mikuni Type
#22.5 Pilot Jet - VM22/210 Mikuni Type
#25
Pilot Jet - VM22/210 Mikuni Type
#27.5 Pilot Jet - VM22/210 Mikuni Type
#30
Pilot Jet - VM22/210 Mikuni Type
Pilot Jet - VM22/210 Type
#35
Pilot Jet - VM22/210 Mikuni Type
Note: Average Standard size for
#40
Pilot Jet - VM22/210 Mikuni Type
XS650C/D (76-77) - #25
#45
Pilot Jet - VM22/210 Mikuni Type
XS650E/SE (78), F/SF/2F(79) - 27.5
#50
Pilot Jet - VM22/210 Mikuni Type
55
CARB JETS/PARTS
Fuel/Carb Section (C)
Version 01 March/05
Jets Sold in multiples
Pilot Jet - BS30/96 Mikuni Type of 2pc. each size Only
Fits: 70-75 & 80-84 650's (34 & 38mm. Mikuni CV carbs)
48-0601
#30
Pilot Jet - BS30/96 Mikuni Type
48-0603
#35
Pilot Jet - BS30/96 Mikuni Type
48-0604
#37.5 Pilot Jet - BS30/96 Mikuni Type
48-0605
#40
Pilot Jet - BS30/96 Mikuni Type
48-0606
#42.5 Pilot Jet - BS30/96 Mikuni Type
48-0607
#45
Pilot Jet - BS30/96 Mikuni Type
48-0608
#47.5 Pilot Jet - BS30/96 Mikuni Type
48-0609
#50
Pilot Jet - BS30/96 Mikuni Type
Pilot Jet - BS30/96 Mikuni Type
Note: Average Standard size for
XS1(70), TX650A (74), XS650B (75) - #45
XS1B (71), XS2 (72), TX650 (73), XS650G/SG (80), XS650H/SH/SJ/SK/SL (81-84) - #42.5
48-0600 Series $6.00pr..
48-0900 Series $6.00pr..
48-0901
48-0902
48-0903
48-0904
48-0905
48-0906
48-0907
Pilot Jet - VM28/486 Mikuni Type Fits: TM36-68 36mm. Flatslide Four-stroke Smoothbore Carb with accelerator pump and
bellcrank type slide mechanism.
#15
Pilot Jet - VM28/486 Mikuni Type
#17.5 Pilot Jet - VM28/486 Mikuni Type
#20
Pilot Jet - VM28/486 Mikuni Type
#22.5 Pilot Jet - VM28/486 Mikuni Type
#25
Pilot Jet - VM28/486 Mikuni Type
#27.5 Pilot Jet - VM28/486 Mikuni Type
Pilot Jet - VM28/486 Mikuni Type
#30
Pilot Jet - VM28/486 Mikuni Type
MIXTURE SCREW KIT
PASSAGE PLUG
Rubber pilot jet Passage Plug (pk./2) Fits:
XS650G/H/SH/SJ/SK/SL (1980-84) stock
BS34 CV Carbs. Used inside float bowl to
seal pilot jet passage - 1 per carb
XS# 48-5002 ..... $3.00/pk./2
IDLE MIXTURE SCREW
Kit - mixture screw Washer, O-Ring &
Blind Plug - Fits: XS650G/H/SH/SJ/SK/SL
Fuel Idle Mixture Screw with Spring washer (1980-84) stock BS34 CV Carbs.
and O-Ring - Fits: Stock BS34 CV Carbs on Plug covers vertical recessed idle mixture
XS650G/H/SH/SJ/SK/SL (1980-84)
XS# screw & keeps out contaminants.
48-5011 ..... $10.00ea.
O-Ring fits under metal Washer at bottom
of mixture screw hole and the engine will not
idle properly if it is not present (O-ring is often disintegrated).
XS# 48-5012 ..... $4.00/kit
IDLE MIXTURE SCREW
IDLE MIXTURE SCREW
Fuel Idle Mixture Screw - (256 type) - Fits: Fuel Idle Mixture Screw - (584 type) - Fits:
XS1/XS1B/XS2/TX650/TX650A/XS650B XS650C/D (1976-77) stock BS38 CV Carbs.
(1970-75) stock BS38 CV Carbs.
XS# 48-5009 .... $4.00ea.
XS# 48-5008 .... $4.00ea.
56
IDLE MIXTURE SCREW
Fuel Idle Mixture Screw with O-Ring - Fits:
XS650E/SE/F/SF/2F(78-79)stock BS38 CV
Carbs. XS# 48-5010 .. $9.00ea.
CARB PARTS
JET NEEDLE - 4JN19
NEEDLE JET - Z 6
Fuel/Carb Section (C)
Version 01 March/05
JET NEEDLE - 4N8
Jet Needle - 4JN19 - Fits: XS1/XS1B/ Needle JET - Z 6 - Fits: XS1/XS1B/XS2/ Jet Needle - 4N8 - Fits: TX650A/XS650B
XS2/TX650(70-73) stock BS38 CV Carbs TX650/A,XS650B (1970-75) stock BS38 (1974-75) stock BS38 CV Carbs.
XS# 48-0653 ... $4.00ea.
CV Carbs. XS# 48-0654 .... $12.00ea. XS# 48-0655 ..... $4.00ea.
NEEDLE JET - Z 8
Jet Needle - Z 8 - Fits: XS650C/D (197677) stock BS38 CV Carbs.
XS# 48-0656 ..... $12.00ea.
JET NEEDLE - 4M1
NEEDLE JET - Z 2
NEEDLE JET - Y-O
Jet Needle - Z 2 - Fits: XS650E/SE(78),
XS650F/SF/2F(79) stock BS38 CV carbs Jet Needle - Y-O - Fits: XS650G/H/SH/
SJ/SK/SL(80-84)stock BS34 CV Carbs.
XS# 48-0658 ..... $12.00ea.
XS# 48-0660 ..... $12.00ea.
JET NEEDLE - 502
JET NEEDLE - 5HX12
Jet Needle - 4M1 - Fits: XS650C/D (1976- Jet Needle - 502 - Fits: XS650E/SE(78), Jet Needle - 5HX12 - Fits:XS650G/H/
XS650F/SF/2F(1979) stock BS38 CV SH/SJ/SK/SL (1980-84) stock BS34 CV
77) stock BS38 CV Carbs.
Carbs. XS# 48-0659 ..... $4.00ea.
Carbs. XS# 48-0661 ..... $4.00ea.
XS# 48-0657 ..... $4.00ea.
NEEDLE JET O-RING
O-Ring - Needle Jet (nozzle main)
Fits: All XS/TX 650 (1970-79) stock BS38
CV Carbs. XS# 48-5020 .... $1.50ea.
CARB SCREWS
Screws - 5mm. (no lock washers) Late CV Lid Screw
- Ref.# 26 Pk./4
XS# 48-0992 .... $2.00/Pk.4
Screws - 5mm. - Early CV Lid & Late CV Bowl Screw
Ref.# 26&17 Pk./4 screws with lockwashers
XS# 48-0991 ... $2.00/Pk.4
Screws - 4mm. Early CV Bowl Screw - Ref.# 17
Pk.4 with lockwashers
XS# 48-0993 ..... $2.00/Pk.4
Screws - 6mm. - Carb Link bar Screw - Ref.# 68 Set of
4 with lockwashers XS# 48-0990 ... $2.00/Set/4
57
Fuel/Carb Section (C)
Version 01 March/05
CARB REBUILT KITS
Carb Rebuild Kits Rebuild 1 Carb Only - Order 2 per Bike
CARB REBUILD KIT
Carb Rebuild Kit - Fits: XS650SG-SL
(1980-84) stock 34mm. CV carbs Kit Contains : Push-in Float Valve
assembly with O-Ring, Carb rubber
CARB REBUILD KIT
passage plug & Float bowl gasket
Carb
Rebuild
Kit - Fits: XS650C/D (19763F7
77) Kit Contains: 8 Hole choke body Gasket,
XS# 48-1408 ..... $12.00/kit
Float bowl Gasket 256, Float Valve assy. 2.0
Note: Carb Kits are produced by
with washer, Pilot Jet #27.5 VM22/210 type,
makers in Japan for a carb series
#135 SmallRound Main Jet N102/221, Pilot
(type) used in world markets and
some components may differ from air Screw and spring, Washer for float bowl
what has been originally installed main jet access plug and Choke plunger.
in your XS/TX650. Some slide XS# 48-1920 ..... $16.00/kit
Needles, Jets, and Mixture Screws
may not match and in these cases
CARB REBUILD KIT
do not use these parts.
Carb Rebuild Kit - Fits: XS650E/SE/F/
SF/2F (1978-79) Kit Contains: 8 Hole choke
body Gasket, Float bowl Gasket 256, Float
Valve assy. 2.0 with washer, Pilot Jet #27.5
VM22/210 type, #135 SmallRound Main
Jet N102/221, Pilot air mixture Screw with
O-Ring and spring, Washer for float bowl
main jet access plug and Choke plunger.
XS# 48-7879 ..... $19.00/kit
CARB REBUILD KIT
Carb Rebuild Kit - Fits: TX650A/XS650B
(74-75) Kit Contains: Slide Needle Y-22
& clip, Pilot jet BS30/96 #42.5, Main Jet
#130 Small round type N102/221, Float
Needle & Seat assembly #2.5, Air screw
with spring, 7 hole choke cover Gasket
and Float bowl Gasket (256)
XS# 48-1919 ..... $14.00/kit
CARB REBUILD KIT
CARB REBUILD KIT
Carb Rebuild Kit - Fits:XS1/XS1B (1970-71)
Kit Contains: Slide needle Y22 & clip, Pilot Jet
BS30/96 #42.5, Main Jet - #130 Small round
N102/221, Float Needle & Seat assembly #2.0,
Air Screw with spring, Choke Plunger & spring,
float bowl Gasket ( 256)
XS# 48-1917 ..... $14.00/kit
Carb Rebuild Kit - Fits:XS2/TX650 (1972-73) Kit
Contains : Slide Needle Y22 & clip, Pilot Jet BS30/96
#42.5, Main Jet - #130 Small round N102/221, Float
Needle & seat assembly #2.0, Air screw with spring,
metal Washer (bowl plug) , and float bowl Gasket
(256)
XS# 48-1918 ..... $14.00/kit
58
CARB HOLDERS/POD FILTERS
Fuel/Carb Section (C)
Version 01 March/05
STOCK TYPE AIR FILTERS
Note: Rejeting is usually required with Pods
RUBBER JOINT - CARB to AIR FILTER BOX
POD AIR FILTER
Pod Air Filter - Oval, tapered K&N type with chrome end
cap. Will fit behind stock XS/TX650 sidecovers.
52mm. ID (2.047") - Fits: 70-79 650's - stock 38mm. CV carbs
XS# 15-0036 ..... $12.00each
54mm. ID (2.125") - Fits: 80-84 XS650 stock 34mm. CV carbs
XS# 15-0035 ..... $12.00each
1pc. of Air box rubber Joint (ref.# 8) & 2pc.of Tension
Spring- (Ref.# 9) Fits: 1970-84 XS/TX 650's - Carb to air
box - right or left side. XS# 15-0671 ... $10.00/3pc.set
CARB HOLDERS
CARB HOLDERS
Carb Holder Set - Fits:Stock BS38 CV Carbs on TX650A 74
& XS650B/C/D (75-77) - Kit Includes 1pc.(RH) #447-13565 &
1pc.(LH) #447-13555 Made in Japan by OEM maker
XS# 48-1480 ...... $36.00/set
Carb Holder Set - Fits:Stock BS34 CV Carbs on 80-84 XS650 +
Mikuni aftermarket VM-34/36 & 38mm. roundslide carbs.
Kit Includes 1pc. each of carb holders OEM # 3G1-13586 &
OEM # 3G1-13596 XS# 20-6038 ..... $34.00/set
Note: Carb holders are Not available for the 70-73 models.
#48-1480 will fit the 70-73 models but there will be some
additional pressure to get them to align with the air box as
the early holders had a slightly different angle.
BLIND PLUG
Blind Plug - Carb Holder Air Barb
XS# 48-1447 .... $1.50ea.
59
Fuel/Carb Section (C)
Version 01 March/05
STOCK AIR FILTERS
All 650's Require 2 Filters per bike and these fit into the stock Airbox
Air Filter - Fits: XS650G-K - All 1980-84 650's
OEM# 3G1-14451 XS# 15-0655 ... $22.00ea.
Air Filter - Fits: XS650C/D/E/SE/F/SF/2F 1976-79
OEM# 533 -14451-00 XS# 15-0653 ... $22.00ea.
Air Filter - Fits: XS1/XS1B 70-71 OEM# 256-14451
XS# 15-0651 ..... $12.00ea.
Air Filter - Fits:XS2/TX650 72-73 OEM# 306-14451
XS# 15-0652 ..... $12.00ea.
Air Filter - Fits: TX650A 1974, XS650B 1975
OEM# 447-14451-01 XS# 15-0654 ... $22.00ea.
60

Similar documents

chassis rubber mounts

chassis rubber mounts Damper Rubber - ( rider footrest bracket ) - Set of 4 (Figure #20) - Fits: All 1970-84 XS/TX650's XS# 02-6527 ..... $16.00/set/4 See Pg 93 for Footrest Crown Nuts & Washers

More information