Abrasive Nylon Disc Brushes

Transcription

TA N I S
INCORPORATED
INDUSTRIAL BRUSHES
An ISO 9001:2008 Certified
Product Index
TECHNICAL INFORMATION
Page
CeramiX® Abrasive Brushes Information
Abrasive Grain Options
Operating Parameters Disc Brushes Operating Parameters Wheel Brushes Troubleshooting Abrasive Brush Products
Maximizing Abrasive Brush Performance 2
3
4
5
6
6
ABRASIVE BRUSHES
Abrasive Nylon Wheel Brushes
Wheel Brush Adapters
Abrasive Nylon Copper Center Wheel Brushes
Air Motor Shanks
Plastic Brushings Narrow Face Wheel Brushes
Stem Mounted Wheels Brushes
Diamond Abrasive Brushes
Abrasive Nylon Disc Brushes
Drive Arbors and Brush Bands
Shell Mill Holder Disc Brushes Mini Disc Brushes Abrasive Nylon End Brushes Stem Mounted End Brushes Fine Blanking Disc Brushes 8-9
10
11
11
11
12-13
14-15
16
17-18
19
20
21
22
23
24
TWISTED BRUSHES
Technical Information Abrasive Nylon Micro Twisted Brushes Abrasive Nylon Collet Ready Brushes
Abrasive Nylon Tube Brushes
Abrasive Nylon Burr Brushes Power Burr Brushes Power Tube Brushes Side Tuft Cleaning Brush Hand Held Heavy Duty Tube Brushes
Hand Held Tube Cleaning Brush
Miniature and Micro Miniature Brushes
Miniature Brush Sets Hand Held Tube Cleaning Brush 25
26-27
28-29
30-31
32-33
34
35
35
36
37
38-39
40
41-42
LABORATORY BRUSHES
Test Tube and Burette Brushes
Centrifuge, Pipette, Babcock and Flask Brushes
Beaker, Cylinder and Bottle Brushes
43
44
45
TA N I S
INCORPORATED
POWER BRUSHES
Copper Center Crimped Wire Wheels Copper Center Non-Metallic Wheels
Copper Center Abrasive Nylon Wheels
Air Motor Shanks Plastic Bushings Radial End Brushes
Conflare Brushes
Wire End Brushes Abrasive Nylon End Brushes Miniature Wheel Brushes
Miniature Cup Brushes Miniature End Brushes 48-49
50
51
51
51
52
53
54
55
56
57
57
MAINTENANCE BRUSHES
Applicator Brushes Small Hand Scratch Brushes General Purpose - Hand Brushes
Steel Wire Hand Scratch Brushes Platers' Hand Brushes Scouring and Scrub Brushes
Anilox Brushes 58
58-59
60
61
62
62
63
ARTIST BRUSHES
Red Sable Marking Brushes
Taklon White Artist Brushes
Round White Bristle Marking Brushes
White Bristle Marking Brushes
Black Bristle Fitch Brushes
Gold Nylon Artist Brushes Camel Hair Flat Lacquering Brushes
Black Sable Ox Hair Stroke Brushes
White Bristle Fan Marking Brushes
Fine White Bristle Stencil Brushes Pony Hair Detail Brushes (Lip Brushes) 64
64
64
64
64
65
65
65
65
65
65
PAINT & PARTS CLEANING BRUSHES
White Bristle Chip Brushes
Polyester Chip Brushes
Round Wire Chip Brushes
Flat Sash Paint Brushes
Oval Sash Paint Brushes
Parts Cleaning Brushes
Round Bridled Glue Brushes
Tin Handle Acid Brushes
Wood Handle Dope Brushes
66
66
66
66
67
67
67
67
67
SAFETY CONSIDERATIONS & REQUIREMENTS
Safety Information for Power Brushes
Inside Back Cover
CUSTOMER SERVICE (800) 234-7002
e-mail: [email protected] • www.tanisbrush.com
PHONE (262) 646-9000 • FAX (262) 646-9005
Tanis Brush - Putting over 25 years of experience to work for you!
Known for our vast selection of brush products, resourceful custom-design capabilities and exceptional customer service, Tanis Brush is becoming
an industry leader in brush manufacturing. Since 1987, our team has remained committed to providing our customers with total customer satisfaction
throughout the entire customer buying experience. Our ISO 9001:2008 certification brings excellence into our daily work environment and encourages us to persistently question and improve our processes, fostering a culture of quality and continuous improvement.
Our corporate campus includes more than 64,000 square feet of combined facility space, and utilizes the latest brush manufacturing technology with
state-of-the-art automation equipment to ensure quality, consistency and value.
Our stock and standard brush offerings include abrasive, twisted, rotary, strip, stapled set, composite, power and utility product categories. We serve
a global customer base including a wide range of OEMs, manufacturing operations, production processes and maintenance operations within a vast
array of industries such as agriculture, printing, food processing, automotive, aerospace, metal fabrication, medical, military and many more.
Tanis carries a large inventory of products, but we also specialize in custom-manufactured industrial brushes to meet the most unique applications.
We offer short production quantities on semiautomatic machines or high volume production on highly automated state-of-the-art equipment to meet
varying volume demands.
Abrasive Grain
CERAMIX® Abrasive Brushes Made with 3M™
Abrasive Grain 321
A superior ceramic abrasive grain creates a superior abrasive brush
The technology dates back to 1981, when 3M Company (St. Paul, MN) introduced the first commercial application of sol gel abrasive grain. The advantages of
this grain stem from how it’s manufactured and is evident in the grain’s microstructure.
The production of conventional fused abrasive grain (such as aluminum oxide or silicon carbide), is a process in
which the raw materials are fused or melted together, cooled and then crushed. This process results in crystal
structures that are usually quite large.
In comparison, sol gel abrasive grain is the product of a chemical process in which an alumina precursor is prepared,
gelled, dried, crushed into particles and then sintered to form abrasive grains. These ceramic abrasive grains may be
embedded in a nylon polymer and the combination extruded into abrasive nylon filaments. The ceramic abrasive
particles produced through sol gel processes have a finer crystalline structure than their conventional counterparts.
Individual fused aluminum oxide abrasive grains typically comprise one to three alumina crystals; sol gel abrasive
grains consist of many multitudes of alumina crystals.
Crystalline Structure
The benefit of this crystalline structure is that as the outermost crystals in the abrasive grain become worn
during use they are expelled in very small fragments, leaving a greater amount of grain in the filament to
continue abrading the part surface. The nylon filaments containing this special ceramic abrasive grain deliver
improved productivity.
Two-Phase Microstructure
The 3M™ ceramic abrasive grain 321 also has a unique two-phase
microstructure, a combination of fine crystals and a platelet phase.
The platelets serve to reinforce the abrasive grains to withstand greater
abrasion forces. The random orientation of the platelets also deflects
fractures into multiple directions, creating a jagged irregular surface after
the grain fractures. This continuous self-sharpening and jagged grain
surface provide superior abrasion for filaments containing 321 ceramic
abrasive grains.
The microstructure of 321 ceramic abrasive grain from 3M allows for
three key traits which contribute to its elevated status: fracture toughness,
hardness, and self-sharpening qualities. These features equate to increased
productivity for CeramiX® abrasive nylon brush filaments, made with
proprietary 3M™ 321 ceramic abrasive grain embedded through the
filament.
Three Key Benefits
CeramiX Brushes
CeramiX nylon abrasive brushes are made exclusively in North America by Tanis, Inc. in Delafield, Wisconsin
and are used as flexible filing tools in deburring and surface conditioning applications. Their flexibility allows these
brushes to conform to irregular surface shapes. Brush designs have been developed for use in power tools,
robotic cells and CNC applications to eliminate the need for time-consuming and inconsistent hand deburring
operations.
Tanis’ abrasive nylon brushes are available in multiple configurations:
tube or burr brushes (also known as twisted-in-wire), strip brushes, and
composite formed disc, mini-disc and radial wheels. CeramiX
high-performance brushes cut three to five times faster on ferrous
metal surfaces due to the properties of the 321 ceramic abrasive
grain, and CermiX performs well under high stress and heat conditions.
CeramiX abrasive nylon filament is available in 220, 180, 120 and 80
grit sizes, in a variety of filament diameters including a heavy-duty
rectangular shape. Tanis regularly designs and manufactures custom
brushes in CeramiX and other filaments to suit customers’ specific applications.
3M is a registered trademark of the 3M company.
CeramiX is a registered trademark of Tanis, Inc.
2
Tanis Brush
(800) 234-7002 | (262) 646-9000
Abrasive Grain
CERAMIX® Performance with 3M™ Abrasive Grain
Cutting Action:
ALUMINUM PLATE
T6 Aluminum Plate,
1750 RPM
CeramiX proprietary abrasive brushes provide
enhanced cutting action up to 3 to 5 times
faster than traditional abrasive filaments.
®
Brush Life:
PERFORATED CRS
Perforated CRS A366 Plate,
1750 RPM
The mineral grain in CeramiX brushes wears
away in smaller pieces, leaving more mineral to
work on the part surface.
®
Increased Throughput:
CRS STEEL PLATE
1008 CRS Plate,
1750 RPM
CeramiX abrasive brushes reduce cycle times,
enabling you to increase throughput.
The controlled surface abrading action provides
a consistent surface finish.
®
Abrasive Grain Options
3M™ Grain 321 used in
CeramiX® Brushes cuts 3
to 5 times faster on ferrous metal
surfaces compared to traditional
abrasive nylons. The mineral grain
in CeramiX® wears away in smaller
chunks leaving more mineral available to continuously work on the part
surface.
Aluminum Oxide is more impact resistant compared to silicon
carbide and less likely to fracture.
AO is preferred for finishing soft
metals or other materials where a
smooth finish is required.
Silicon Carbide is harder,
sharper and more aggressive than
aluminum oxide and is preferred
for finishing ferrous metals.
Alumina Silicate is a hard
ceramic with low thermal expansion. This fine grain abrasive
filament is well-suited for fine
finishing and cleaning.
Diamond is a hard ceramic
with low thermal expansion. This
fine grain abrasive filament is
well-suited for fine finishing and
cleaning. See page 16 for more
information on Diamond.
Filament Types:
Round Crimped: optimizes brush conformability
Round Level: maximizes brush density
Grit Size
(rectangular filament)
Silicon Carbide
(rectangular filament)
Aluminum Oxide
46
Filament Diameter
Options (in.)
Abrasive Filament
CeramiXTM
60
180
220
.040, .055 .028, .040 .035
80
120
.022
240
320
500
.030
.022
.018
600
Rectangular: maximum contact with part surface
.045x.090
.060
.045 .040, .050 .022, .040 .035
.045x.090
.040
.035
.030
.022
.018
www.tanisbrush.com
.012
Point of
Contact
Solid Line
Contact
Round Filament
Rectangular Filament
[email protected]
3
Abrasive Brushes
Operating Parameters - Abrasive Nylon Disc Brushes
Disc Diameter
Dry Application
Starting RPM
Recommended
Motor Size
(based on a 1” brush face)
Disc Diameter
Feed Rate
Stainless Steel /
Alloy Steels
Feed Rate
Mild Steel /
Cast Iron
Feed Rate
Aluminum /
Non-Ferrous
2”
3”
4”
5”
6”
8”
10”
12”
1,750 - 2,500
1,750 - 2,500
1,750 - 2,500
1,500 - 1,750
1,250 - 1,750
800 - 1,200
700 - 800
600 - 700
1/4 HP
1/4 HP
1/4 HP
1/4 HP
1/2 HP
3/4 HP
1 HP
1 HP
2”
3”
4”
5”
6”
8”
10”
12”
12 - 18” /min
12 - 18” /min
12 - 18” /min
12 - 18” /min
12 - 18” /min
12 - 18” /min
12 - 18” /min
12 - 18” /min
25 - 30” /min
25 - 30” /min
25 - 30” /min
25 - 30” /min
25 - 30” /min
25 - 30” /min
25 - 30” /min
25 - 30” /min
35 - 50” /min
35 - 50” /min
35 - 50” /min
35 - 50” /min
35 - 50” /min
35 - 50” /min
35 - 50” /min
35 - 50” /min
Abrasive nylon disc brushes work best at speeds allowing fairly deep penetration of the work piece into the brush filaments. Faster speeds do not typically work as well as slower speeds,
since the maximum RPM listed on the brush is not the optimum working speed. A good rule of thumb is to stay below 2,500 SFPM in dry applications and 3,500 SFPM with coolant.
Rotational Direction:
On the initial pass of the brush, rotation should
be in the opposite direction of the cutting tool
that created the burr.
Brush Path:
The ideal brush path is in the opposite
direction of travel from the cutting tool
that created the burr. The brush path
should also be longer than the cutting
tool path, to a point where the trailing
edge of the brush is effective on the
end of the part. Lastly, to maximize the
amount of filament that is striking the
part, the centerline of the brush should
be offset from the center of the part.
Disc Brush Terminology:
Penetration (Point of contact):
The abrasive action occurs when the sides of the brush filament slide
across the part surface or edge of the part. When the correct balance
between speed (RPM), penetration, dwell time and abrasive grit size are
achieved, then optimum life and cut can be obtained.
Recommended penetration rates for abrasive nylon disc brushes are from
.075” - .100”. This will allow long brush life with aggressive abrasive action.
Correct point of contact
4
Tanis Brush
(800) 234-7002 | (262) 646-9000
Incorrect point of contact
Abrasive Brushes
Operating Parameters - Abrasive Nylon Wheel Brushes
Wheel Diameter
4”
5”
6”
8”
10”
12”
14”
Dry Application
Starting RPM
2,000 - 3,000
2,000 - 3,000
1,500 - 2,000
1,200 - 1,500
1,000 - 1,200
800 - 1,000
800 - 900
Recommended
Motor Size
Surface Speed (peripheral speed in feet per minute)
(based on a 1” brush face)
1/4 HP
1/4 HP
1/2 HP
3/4 HP
1 HP
1 HP
1 HP
Abrasive nylon wheel brushes work best at speeds allowing fairly deep penetration
of the work piece into the brush filaments. Faster speeds do not typically work
as well as slower speeds, since the maximum RPM listed on the brush is not the
optimum working speed. A good rule of thumb is to stay below 2,500 SFPM in
dry applications and 3,500 SFPM with coolant. When operating multiple wheel
brushes on a common shaft, multiply the HP requirements listed above times the
number of brushes in use.
RPM
4” dia
6” dia
8” dia
10” dia
12” dia
900
950
1400
1900
2350
2800
14” dia
3350
1150
1200
1800
2400
3000
3600
4200
1200
1250
1900
2500
3200
3800
4400
1500
1550
2350
3150
3900
4700
5500
1750
1800
2750
3650
4550
5500
6400
2000
2100
3100
4200
5200
6300
7300
2400
2500
3800
5000
6100
7500
8800
2800
2900
4400
5850
7300
8800
10200
3000
3100
4700
6300
7800
9400
11000
3200
3350
5000
6700
8400
10200
11700
3450
3600
5400
7200
9000
11000
12600
13700
3750
3900
5900
7800
9800
11800
4000
4200
6300
8400
10500
12500
14100
4500
4700
7200
9400
11900
5000
5200
7800
10500
13100
5400
5600
8500
11300
6000
6300
9400
12500
π Dia (inches) X RPM
12
Wheel Brush Terminology:
Penetration (Point of contact):
The abrasive action occurs when the sides of the brush filament
slides across the part surface or edge of the part. When the correct
balance between speed (RPM), penetration, dwell time and abrasive
grit size are achieved, then optimum life and cut can be obtained.
Recommended penetration rates for abrasive nylon disc brushes
are from .075” - .100”. This will allow long brush life with aggressive
abrasive action.
Correct point of contact
Incorrect point of contact
Considerations when selecting filament for a Tanis abrasive nylon brush
Grit Size:
120 grit is our recommended starting point for most applications. From there you can move
either down or up in grit size, for a more agressive cutting action or more of a polishing
action. The chart on page 2 shows our abrasive nylon filament/grit size options.
Trim Length and Brush Density:
A brush with a short trim length is rigid and used for high speed cutting. Longer trim lengths
are more flexible and used for conforming to irregular surfaces. Likewise, a brush with a
lower fill density has greater flexibility and ability to conform, as well as increased resiliency.
High fill density brushes are used for deburring and when high speed cutting is required.
www.tanisbrush.com
Long trim, lower density
[email protected]
Shorter trim, high density
5
Abrasive Brushes
Troubleshooting - Abrasive Nylon Brushes
Brush too aggressive • Reduce filament diameter and/or grit size
• Reduce surface speed by reducing RPM
• Increase trim length and decrease fill density
• Increase feed rate
• Use a smaller diameter brush
Brush not aggressive enough • Increase filament density and/or grit size
• Increase surface speed by increasing RPM
• Decrease trim length
• Reduce feed rate
• Use a larger diameter brush
Brush not conforming enough to part • Increase trim length
• Reduce filament density
• Reduce surface speed by reducing RPM
Final finish too rough • Increase surface speed by increasing RPM
• Use a larger diameter brush
• Use a finer abrasive filament
• Use a coolant or cutting oil
• Use a buffing compound
Final finish too smooth • Reduce surface speed by reducing RPM
• Increase filament density and/or grit size
Filament smearing/melting • Reduce surface speed by reducing RPM
• Decrease brush diameter
• Use a coolant or lubricant
More action needed on edges parallel to brush axis • Reduce surface speed by reducing RPM
• Keep longer brush contact on problem area
More action needed on edges • Reduce surface speed by reducing RPM
perpendicular to brush axis • Increase feed rate
• Oscillate brush on problem area
Brush action not uniform enough • Increase trim length
• Reduce filament density
• Use automated equipment for brush motion
Short brush life • Increase filament density
• Reduce pressure/depth of interference
Suggestions for Maximizing Brush Performance
Feature
Decrease
Increasing outside diameter at a constant RPM increases
surface speed: SFPM (Surface Feet Per Minute). Increasing
surface speed increases work results.
Assuming constant RPM, a decrease in tool diameter decreases
surface speed.
Increasing RPM at a constant outside diameter increases
surface speed.
Assuming same diameter brush, decreasing RPM decreases surface
speed
Allows the filament to be more flexible, and to conform more
readily to irregular surfaces.
Stiffens filament action, thereby increasing work accomplished.
Provides faster cutting action and thereby increases work
accomplished.
NOTE: Coarser filament/grit sizes work faster than finer
filament/ grit sizes, with faster wear.
Provides superior surface finish and maximize tool life.
NOTE: For best results, choose minimum diameter, and increase as
needed.
GRIT SIZE
Provides faster cutting action and thereby increases work accomplished. NOTE: Coarser filament/grit sizes work faster than
finer filament/ grit sizes, with faster wear.
Provides superior surface finish and maximize tool life.
For best results, choose minimum grit size, and increase as needed.
FILAMENT
DENSITY
Provides more filament to do work, thereby increasing work
accomplished
Provides greater brush flexibility; leaving more room for individual
filaments to conform to irregular workpiece shapes.
DIAMETER
RPM
TRIM LENGTH
FILAMENT SIZE
6
Increase
Tanis Brush
(800) 234-7002 | (262) 646-9000
Abrasive Brushes
Let us help with your deburring challenges!
Tanis’ in-house engineering department will work with you to recommend a brush or design
a custom brush capable of tackling your most difficult deburring challenges.
Our offering of abrasive nylon brushes continues to grow, with multiple new disc and twist
configurations in this catalog and on our website. Tanis representatives across the United
States are available to visit your location and work with you in person to find the best solution to your deburring challenge - call or email us to let us know how we can help you.
www.tanisbrush.com
[email protected]
7
Abrasive Brushes
CERAMIX® ABRASIVE NYLON WHEEL BRUSHES
Tanis abrasive nylon wheel brushes are made with CeramiX filament molded into a urethane based composite hub construction. The
proprietary grain mineral in CeramiX is exclusive to Tanis, and was developed with 3M. CeramiX provides enhanced cutting action up to 3 to 5 times faster
than traditional abrasive filaments. The mineral wears away in smaller pieces, consistently leaving more mineral in the filament to work on the part surface.
*Honing with brushes increases
lubricity and facilitates chip flow.
Arbor hole adapters available on
page 10.
8
Tanis Brush
1/2”
1”
10,000
2”
1”
1-1/4”
3,600
2”
1”
1-1/4”
3,600
2”
1”
2-1/4”
3,600
2”
1”
1-1/2”
3,600
2”
1”
3-1/4”
3,600
4-1/4”
1”
1-1/2”
1,800
4-1/4”
1”
3”
1,800
5-1/4”
1”
1-1/2”
1,800
5-1/4”
1”
3-1/2”
1,800
LONG
• Hone drill point lip edge on
carbide drills
5/8”
SHORT
• Post coat polish of flutes on
carbide drills
MAX.
RPM
LONG
• Improving surface finish
TRIM
LENGTH
SHORT
• Edge radiusing
FACE
WIDTH
LONG
• Light duty cleaning/finishing
ARBOR
HOLE
SHORT
• Turbine blade surface finishing
80
80
120
120
180
220
80
80
80
120
120
180
220
80
80
80
120
120
180
220
80
80
80
120
180
220
80
80
80
120
120
180
220
80
80
80
120
180
220
80
80
80
120
120
180
220
80
80
80
120
180
220
80
80
80
120
120
180
220
80
80
80
120
180
220
FILAMENT
DIAMETER
.040
.055
.028
.040
.035
.022
.040
.055
.045 x .090
.028
.040
.035
.022
.040
.055
.045 x .090
.028
.040
.035
.022
.040
.055
.045 x .090
.040
.035
.022
.040
.055
.045 x .090
.028
.040
. 035
.022
.040
.055
.045 x .090
.040
.035
.022
.040
.055
.045 x .090
.028
.040
.035
.022
.040
.055
.045 x .090
.040
.035
.022
.040
.055
.045 x .090
.028
.040
.035
.022
.040
.055
.045 x .090
.040
.035
.022
LONG
• Machine part deburring
GRIT
(800) 234-7002 | (262) 646-9000
TRIM
SHORT
APPLICATIONS:
TANIS
BRUSH
PART NO. DIAMETER
30105
30107
30110
4”
30115
30120
30125
30130
30132
30135
6”
30140
30145
30150
30155
30160
30162
30165
8”
30170
30175
30180
30185
30190
30192
30195
8”
30200
30205
30210
30215
30217
30220
10”
30225
30230
30235
30240
30245
30247
30250
10”
30255
30260
30265
30270
30272
30275
12”
30280
30285
30290
30295
30300
30302
30305
12”
30310
30315
30320
30325
30327
30330
30335
14”
30340
30345
30350
30355
30357
30360
14”
30365
30370
30375
Abrasive Brushes
SILICON CARBIDE ABRASIVE NYLON WHEEL BRUSHES
Tanis silicon carbide abrasive nylon wheel brushes are made using nylon filament impregnated with a traditional grit. Silicon carbide is known for its durability
and preferred for finishing ferrous metals. It provides a consistent finish with controlled surface abrading action and less filament breakage than wire brushes.
TANIS
BRUSH
PART NO. DIAMETER
4”
6”
8”
1/2”
1”
10,000
2”
1”
1-1/4”
3,600
APPLICATIONS:
2”
1”
1-1/4”
• Machine part deburring
3,600
• Turbine blade surface finishing
• Light duty cleaning/finishing
2”
2”
2”
1”
1”
1”
2-1/4”
1-1/2”
3-1/4”
3,600
3,600
3,600
4-1/4”
1”
1-1/2”
1,800
4-1/4”
1”
3”
1,800
5-1/4”
1”
1-1/2”
1,800
5-1/4”
1”
3-1/2”
1,800
www.tanisbrush.com
[email protected]
LONG
14”
5/8”
.040
.022
.040
.035
.022
.018
.040
.045 x .090
.022
.040
.035
.022
.018
.040
.045 x .090
.022
.040
.035
.022
.040
.045 x .090
.040
.035
.022
.040
.045 x .090
.022
.040
. 035
.022
.040
.045 x .090
.040
.035
.022
.040
.045 x .090
.022
.040
.035
.022
.040
.045 x .090
.040
.035
.022
.040
.045 x .090
.022
.040
.035
.022
.040
.045 x .090
.040
.035
.022
TRIM
SHORT
14”
RPM
LONG
12”
MAX.
LENGTH
SHORT
12”
TRIM
WIDTH
LONG
10”
FACE
HOLE
SHORT
10”
ARBOR
LONG
8”
80
120
120
180
320
500
80
80
120
120
180
320
500
80
80
120
120
180
320
80
80
120
180
320
80
80
120
120
180
320
80
80
120
180
320
80
80
120
120
180
320
80
80
120
180
320
80
80
120
120
180
320
80
80
120
180
320
FILAMENT
DIAMETER
SHORT
30380
30385
30390
30395
30400
30405
30410
30415
30420
30425
30430
30435
30440
30445
30450
30455
30460
30465
30470
30475
30480
30485
30490
30495
30500
30505
30510
30515
30520
30525
30530
30535
30540
30545
30550
30555
30560
30565
30570
30575
30580
30585
30590
30595
30600
30605
30610
30615
30620
30625
30630
30635
30640
30645
30650
30655
30660
GRIT
Made in USA
• Edge radiusing
carbide drills
• Hone drill point lip edge on
carbide drills
*Honing with brushes increases
lubricity and facilitates chip flow.
Arbor hole adapters available on
page 10.
Always wear safety
goggles and protective
clothing when
using power
brushes.
9
Abrasive Brushes
Wheel Brush Terminology:
WHEEL BRUSH ADAPTERS
These slip-fit metal adapters are used for mounting nylon abrasive wheel brushes into smaller
shafts. Sold in pairs. Available for 4-1/4” and 5-1/4” brush I.D. wheels and 2” brush I.D. wheels.
TANIS
ADAPTER FITS
ARBOR HOLE
ADAPTER
I.D.
KEYWAY
PART NUMBER
35040
35045
4-1/4”
5-1/4”
2”
2”
1/2 x 1/4 (2)
1/2 x 1/4 (2)
TANIS
ADAPTER FITS
PART NUMBER
ARBOR HOLE
35005
35010
35015
35020
35025
35030
35035
2”
2”
2”
2”
2”
2”
2”
10
SIZE
ADAPTER I.D.
1/2”
5/8”
3/4”
7/8”
1”
1-1/4”
1-1/2”
Tanis Brush
(800) 234-7002 | (262) 646-9000
Abrasive Brushes
CERAMIX® COPPER CENTER WHEEL BRUSHES
CeramiX® small profile wheels for cleaning, polishing and deburring recessed areas such as small openings, slots, machined grooves, fine deburring
on medical instruments and gear splines. CeramiX® contains 3M™ Company 321 mineral grain which provides enhanced cutting action up to 3-5
times greater than traditional abrasive filaments. CeramiX® fractures in sharper, jagged surfaces for superior abrasion providing minimum cycle
times, increased productivity and maximizes abrasive media on part.
TANIS
PART NO.
35505
35510
35515
35520
35525
35530
35535
35540
35545
35550
BRUSH
DIAMETER
1-1/2”
2”
2-1/2”
3”
FILAMENT
DIAMETER
.028
.028
.035
.040
.028
.040
.028
.035
.040
.040
GRIT
120
120
180
80
120
80
120
180
120
80
ARBOR
HOLE
1/2”
FACE
WIDTH
3/16”
TRIM
LENGTH
1/4”
1/2”
1/4”
5/8”
5/16”
5/8”
10,000
1/2”
3/8”
7/8”
10,000
3/8”
MAX
RPM
10,000
10,000
SILICON CARBIDE COPPER CENTER WHEEL BRUSHES
Silicon Carbide small profile wheels are known for durability and preferred for finishing ferrous metals.
TANIS
PART NO.
35570
35575
35580
35585
35590
35595
35600
35605
35610
35615
35620
35625
BRUSH
DIAMETER
1-1/2”
2”
2-1/2”
3”
FILAMENT
DIAMETER
.035
.022
.018
.022
.040
.022
.035
.022
.022
.035
.022
.040
GRIT
180
120
500
120
120
320
180
120
320
180
120
120
ARBOR
HOLE
FACE
WIDTH
TRIM
LENGTH
MAX
RPM
1/2”
3/16”
1/4”
10,000
1/2”
1/4”
1/2”
10,000
5/8”
5/16”
5/8”
10,000
1/2”
3/8”
7/8”
10,000
Air Motor Shanks
For air motors and flexible shafts. Accepts single or multiple brushes.
10033
TANIS
SHANK
ARBOR
FOR ARBOR
OVERALL
PART NO.
10030
10031
10032
10033
DIAMETER
1/4”
1/4”
3/16”
1/4”
HOLE
1/2”
3/8”
1/4”
5/8”
WIDTH UP TO
3/8”
3/8”
3/4”
3/8”
LENGTH
1-7/8”
1-5/8”
1-3/4”
1-7/8”
10032
10031
Plastic Bushings
Plastic bushings are designed for economical, one-time use to match the brush inside diameter with your mounting shaft. Available in a range of inner and
outer diameters. For safety, use only one per brush. Flange eliminates side movement.
TANIS
OUTSIDE
INSIDE
PART NO.
10035
10036
10037
10038
DIAMETER
3/8”
1/2”
1/2”
5/8”
DIAMETER
1/4”
1/4”
3/8”
1/2”
www.tanisbrush.com
[email protected]
Made in USA
11
Abrasive Brushes
CERAMIX® NARROW FACE WHEEL BRUSHES
CeramiX® narrow face wheel brushes are used for cleaning, polishing and deburring recessed applications such as small openings, slots, machined grooves,
fine deburring on medical instruments and gear splines. CeramiX® contains 3M™ Company 321 mineral grain which provides enhanced cutting action up to
3-5 times greater than traditional abrasive filaments. CeramiX® fractures in sharper, jagged surfaces for superior abrasion providing minimum cycle times,
increased productivity and maximizes abrasive media on part. Filament is molded into a urethane based composite hub construction providing controlled filament density and balanced wheel enhancing brush life.
TANIS
BRUSH
PART NO. DIAMETER
35100
35103
35106
35109
35112
35115
35118
35121
35124
35136
35139
35142
35145
35148
35151
35163
35166
35169
35172
35175
35178
35190
35193
35196
APPLICATIONS:
• Deburring keyways, slots and
machines grooves in parts
3”
3”
4”
4”
5”
5”
6”
6”
GRIT
80
120
120
80
120
120
80
120
120
80
120
120
80
120
120
80
120
120
80
120
120
80
120
120
FILAMENT
ARBOR
FACE
TRIM
MAX.
DIAMETER
HOLE
WIDTH
LENGTH
RPM
3/8”
3/8”
1”
10,000
3/8”
1/4”
1”
10,000
5/8”
1/2”
1”
10,000
5/8”
1/4”
1”
10,000
5/8”
1/2”
1-1/2”
6,000
5/8”
1/4”
1-1/2”
6,000
5/8”
1/2”
2”
6,000
5/8”
1/4”
2”
6,000
.040
.028
.040
.040
.028
.040
.040
.028
.040
.040
.028
.040
.040
.028
.040
.040
.028
.040
.040
.028
.040
.040
.028
.040
• Deburring gear splines
• Honing and finishing of
cylindrical bores
• Deburring cross holes in large
bearing bores
• Edge radiusing
• Deburring seal grooves in
turbine engine cases and small
aerospace parts
12
Tanis Brush
(800) 234-7002 | (262) 646-9000
Abrasive Brushes
SILICON CARBIDE NARROW FACE WHEEL BRUSHES
Silicon Carbide Narrow Face wheels are known for durability and preferred for finishing ferrous metals. Filament is molded into a urethane based composite
hub construction providing controlled filament density and balanced wheel enhancing brush life.
TANIS
BRUSH
PART NO. DIAMETER
35199
35202
35205
35208
35211
35214
35217
35220
35223
35235
35238
35241
35244
35247
35250
35262
35265
35268
35271
35274
35277
35289
35292
35295
3”
3”
4”
4”
5”
5”
6”
6”
GRIT
80
120
120
80
120
120
80
120
120
80
120
120
80
120
120
80
120
120
80
120
120
80
120
120
FILAMENT
ARBOR
FACE
TRIM
MAX.
DIAMETER
HOLE
WIDTH
LENGTH
RPM
3/8”
3/8”
1”
10,000
3/8”
1/4”
1”
10,000
5/8”
1/2”
1”
10,000
5/8”
1/4”
1”
10,000
5/8”
1/2”
1-1/2”
6,000
5/8”
1/4”
1-1/2”
6,000
5/8”
1/2”
2”
6,000
.040
.022
.040
.040
.022
.040
.040
.022
.040
.040
.022
.040
.040
.022
.040
.040
.022
.040
.040
.022
.040
.040
.022
.040
APPLICATIONS:
5/8”
1/4”
2”
6,000
cylindrical bores
bearing bores
• Edge radiusing
aerospace parts
Always wear safety goggles and
protective clothing when using
power brushes.
www.tanisbrush.com
[email protected]
Made in USA
13
Abrasive Brushes
CERAMIX® STEM MOUNTED NARROW FACE WHEEL BRUSHES
CeramiX® stem mounted narrow face wheel brushes used for cleaning, polishing and deburring recessed applications such as small openings, slots,
machined grooves, fine deburring on medical instruments and gear splines. CeramiX® contains 3M™ Company 321 mineral grain which provides enhanced
cutting action up to 3-5 times greater than traditional abrasive filaments. CeramiX® fractures in sharper, jagged surfaces for superior abrasion providing
minimum cycle times, increased productivity and maximizes abrasive media on part. Filament is molded into a urethane based composite hub construction
providing controlled filament density and balanced wheel enhancing brush life. Stem diameter is 1/4” and molded into block
TANIS
BRUSH
PART NO. DIAMETER
APPLICATIONS:
35298
35301
35304
35307
35310
35313
35316
35319
35322
35334
35337
35340
35343
35346
35349
35361
35364
35367
35370
35373
35376
35388
35391
35394
3”
3”
4”
4”
5”
5”
6”
6”
GRIT
80
120
120
80
120
120
80
120
120
80
120
120
80
120
120
80
120
120
80
120
120
80
120
120
FILAMENT
SHANK
FACE
TRIM
MAX.
DIAMETER
DIAMETER
WIDTH
LENGTH
RPM
1/4”
3/8”
1”
10,000
1/4”
1/4”
1”
10,000
1/4”
1/2”
1”
10,000
1/4”
1/4”
1”
10,000
1/4”
1/2”
1-1/2”
4,500
1/4”
1/4”
1-1/2”
4,500
1/4”
1/2”
2”
4,500
1/4”
1/4”
2”
4,500
.040
.028
.040
.040
.028
.040
.040
.028
.040
.040
.028
.040
.040
.028
.040
.040
.028
.040
.040
.028
.040
.040
.028
.040
cylindrical bores
bearing bores
• Edge radiusing
aerospace parts
14
Tanis Brush
(800) 234-7002 | (262) 646-9000
Abrasive Brushes
SILICON CARBIDE STEM MOUNTED NARROW FACE WHEEL BRUSHES
Silicon Carbide Stem Mounted Narrow Face wheels are known for durability and preferred for finishing ferrous metals. Filament is molded into a urethane
based composite hub construction providing controlled filament density and balanced wheel enhancing brush life. Stem diameter is ¼” and molded into the
block.
TANIS
BRUSH
PART NO. DIAMETER
35397
35400
35403
35406
35409
35412
35415
35418
35421
35433
35436
35439
35442
35445
35448
35460
35463
35466
35469
35472
35475
35487
35490
35493
3”
3”
4”
4”
5”
5”
6”
6”
GRIT
80
120
120
80
120
120
80
120
120
80
120
120
80
120
120
80
120
120
80
120
120
80
120
120
FILAMENT
SHANK
FACE
TRIM
MAX.
DIAMETER
DIAMETER
WIDTH
LENGTH
RPM
1/4”
3/8”
1”
10,000
1/4”
1/4”
1”
10,000
1/4”
1/2”
1”
10,000
1/4”
1/4”
1”
10,000
1/4”
1/2”
1-1/2”
4,500
1/4”
1/4”
1-1/2”
4,500
1/4”
1/2”
2”
4,500
1/4”
1/4”
2”
4,500
.040
.022
.040
.040
.022
.040
.040
.022
.040
.040
.022
.040
.040
.022
.040
.040
.022
.040
.040
.022
.040
.040
.022
.040
protective clothing when using
power brushes.
www.tanisbrush.com
[email protected]
Made in USA
15
Abrasive Brushes
DIAMOND GRIT ABRASIVE BRUSHES
Diamond grit abrasive brush products introduced by Tanis Incorporated. Diamond brushes are most effective on super hard materials such as tungsten carbide,
ceramics, diamond and glass. These tools are used for polishing, edge radiusing and deburring applications. Diamond wheel brush tools are effective on drill
honing, polishing and honing indexable cutting tool inserts.
Diamond
Grit
120
240
400
600
1000
Filament Diameter
.040
.040
.020
.020
.010
APPLICATIONS:
carbide drills
• Edge honing drill point lip
edge on carbide drills
• Edge honing indexable cutting
tools inserts
Please contact Tanis Brush technical sales for more information about our Diamond Grit
Brushes.
Always wear safety goggles
and protective clothing
when using power
brushes.
16
Tanis Brush
(800) 234-7002 | (262) 646-9000
Abrasive Brushes
CERAMIX® ABRASIVE NYLON DISC BRUSHES
The composite molded construction of Tanis disc brushes creates a tough, high-productivity brush tool. Higher fill densities allow for a more aggressive brush,
making this brush capable of maximized productivity. Alternative filament patterns are available for applications requiring maximum density (teardrop pattern) or
lighter filament density (tufted pattern). For more information on Tanis’ exclusive CeramiX® filament, see page 2.
TUFTED TEARDROP BRUSH
PART NO. PART NO. DIAMETER
GRIT
FILAMENT
ARBOR
TRIM
MAX.
DIAMETER
HOLE
LENGTH
RPM
7/8"
1-1/2"
2,500
7/8"
1-1/2"
2,500
7/8"
1-1/2"
1,750
7/8"
1-1/2"
1,750
33730
33250
80
33732
33252
80
.055
33735
33255
80
.045 X .090
33740
33260
33745
33265
3"
.040
120
.028
120
.040
33750
33270
180
.035
33755
33275
220
.022
33760
33280
80
.040
33762
33282
80
.055
33765
33285
80
.045 X .090
33770
33290
120
.028
4"
33775
33295
120
.040
33780
33300
180
.035
33785
33305
220
.022
33790
33310
80
.040
33792
33312
80
.055
33795
33315
80
.045 X .090
33800
33320
120
.028
5"
33805
33325
120
.040
33810
33330
180
.035
33815
33335
220
.022
33820
33340
80
.040
33822
33342
80
.055
33825
33345
80
.045 X.090
33830
33350
120
.028
6"
33835
33355
120
.040
33840
33360
180
.035
Tufted Pattern
Teardrop Pattern
33845
33365
220
.022
33850
33370
80
.040
APPLICATIONS:
33852
33372
80
.055
33855
33375
80
.045 X .090
• Cast part deburring
33860
33380
120
.028
8"
7/8"
1-1/2"
1,200
• Airframe components
33865
33385
120
.040
• Deburring face-milled parts
33870
33390
180
.035
• Blending grinding marks
33875
33395
220
.022
33880
33400
80
.040
33882
33402
80
.055
33885
33405
80
.045 X .090
10"
33890
33410
120
.028
33895
33415
120
.040
33900
33905
33910
33912
33915
33920
33925
33930
33935
33420
33425
33430
33432
33435
33440
33445
33450
33455
180
220
80
80
80
120
120
180
220
.035
.022
.040
.055
.045 x .090
.028
.040
.035
.022
12”
www.tanisbrush.com
7/8"
1-1/2"
800
7/8”
1-1/2”
800
Drive arbors can be found on
page 19.
[email protected]
Made in USA
17
Abrasive Brushes
SILICON CARBIDE ABRASIVE NYLON DISC BRUSHES
Our exclusive teardrop-shaped filament configuration provides the best of both worlds -- heavy duty abrasive action with sufficient room for air or coolant flow.
Tufted configuration is designed for light-to-medium abrasive action applications. Custom engineered disc brushes can also be produced to suit your application,
in a variety of abrasive nylon filament choices.
Tufted Pattern
Teardrop Pattern
APPLICATIONS:
Drive arbors can be found on
page 19.
18
TUFTED
TEARDROP
BRUSH
PART NO.
PART NO.
DIAMETER
33490
33010
80
.040
33495
33015
80
.045 X .090
33500
33020
120
.022
33505
33025
120
.040
33510
33030
180
.035
33515
33035
320
.022
33520
33040
80
.040
33525
33045
80
.045 X .090
33530
33050
120
.022
33535
33055
120
.040
33540
33060
180
.035
33545
33065
320
.022
33550
33070
80
.040
3"
4"
GRIT
FILAMENT
ARBOR
TRIM
MAX.
DIAMETER
HOLE
LENGTH
RPM
7/8"
1-1/2"
2,500
7/8"
1-1/2"
2,500
7/8"
1-1/2"
1,750
7/8"
1-1/2"
1,750
7/8"
1-1/2"
1,200
7/8"
1-1/2"
800
7/8"
1-1/2"
700
33555
33075
80
.045 X .090
33560
33080
120
.022
33565
33085
120
.040
33570
33090
180
.035
33575
33095
320
.022
33580
33100
80
.040
33585
33105
80
.045 X .090
33590
33110
120
.022
33595
33115
120
.040
33600
33120
180
.035
33605
33125
320
.022
33610
33130
80
.040
33615
33135
80
.045 X .090
33620
33140
120
.022
33625
33145
120
.040
33630
33150
180
.035
33635
33155
320
.022
33640
33160
80
.040
33645
33165
80
.045 X .090
33650
33170
120
.022
33655
33175
120
.040
33660
33180
180
.035
33665
33185
320
.022
33670
33190
80
.040
5"
6"
8"
10"
33675
33195
80
.045 X .090
33680
33200
120
.022
33685
33205
120
.040
33690
33210
180
.035
33695
33215
320
.022
Tanis Brush
12"
(800) 234-7002 | (262) 646-9000
Abrasive Brushes
DISC BRUSH DRIVE ARBORS (Disc brushes found on pages 17-18)
Used to securely mount disc brushes for use in any type of milling machine or CNC machine.
Drive arbor shaft is 3/4” diameter for use in any live tool holder. Drive arbor includes bolt and washer,
DRIVE ARBOR
PART NO.
35050
FOR BRUSH
DIAMETER
SHAFT
DIAMETER
NUMBER OF
LOCATOR PINS
35055
3”, 4" & 5”
3/4”
2
6”
3/4”
35060
2
6”
3/4”
3
35065
8”
3/4”
4
35070
10”, 12”, 14”
3/4”
4
REPLACEMENT
BOLT/WASHER KIT
35075
FOR BRUSH
DIAMETER
ALL
DISC BRUSH BANDS (Disc brushes found on pages 17-18)
Apply to disc or end brushes to prevent flare and enhance aggressive action. To use,
insert bands on disc where filament meets composite material.
RING
ID
TANIS
PART NO.
FOR BRUSH
DIAMETER
35080
1-1/2”
1-1/8”
1-1/2”
.210”
35082
2”
1-1/2”
1-7/8”
.210”
35083
2-1/2”
2”
2-3/8”
.210”
35084
3”
2-1/2”
2-7/8”
.210”
RING
OD
RING
WIDTH
35086
4”
3-1/4”
3-5/8”
.210”
35088
5”
4-3/8”
4-3/4”
.210”
35090
6”
5-1/8”
5-5/8”
.275”
35092
8”
7”
7-1/2”
.275”
35094
10”
9”
9-1/2”
.275”
35096
12”
11”
11-1/2”
.275”
35098
14”
13”
13-1/2”
.275”
*Package quantity of 3 per pack.
Disc Brush Terminology:
when using power
brushes.
www.tanisbrush.com
[email protected]
Made in USA
19
Abrasive Brushes
CERAMIX® SHELL MILL HOLDER DISC BRUSHES
CeramiX® shell mill disc brushes provide a consistent, flat brush for superior dimensional precision. CeramiX® filament provides exceptional abrasive action in deburring applications on flat surfaces, improving metal finish on milled and machined surfaces as well as blending rough edges on
machined parts. Shell mill disc brush has built-in keyway to mount directly to a standard shell mill holder for use in CNC machining centers.
TANIS
BRUSH
PART NO.
DIAMETER
TRIM
MAX.
HOLE
LENGTH
RPM
.75”
1-1/2"
.75”
1-1/2"
120
.028
120
.040
80
.040
34798
80
.055
34791
80
.045 X.090
34801
120
.028
34806
120
.040
80
.040
2”
3”
34818
80
.055
34811
80
.045 X.090
*32362
120
.028
*32369
32376
4"
120
.040
80
.040
32378
80
.055
32371
80
.045 X.090
*32382
120
.028
*32386
120
.040
80
.040
80
.055
32391
80
.045 X.090
*32401
120
.028
32396
6"
32398
*32408
Both brush patterns feature shell mill mount fits standard shell mill holders.
(not included)
ARBOR
34781
34816
*Tufted Pattern
FILAMENT
DIAMETER
34786
34796
Dense Pattern
GRIT
32416
8"
32418
120
.040
80
.040
80
.055
32411
80
.045 X.090
*32421
120
.028
*32426
120
.040
32436
10"
80
.040
32438
80
.055
32431
80
.045 X .090
2,500
1.25"
1-1/2"
1.25"
1-1/2"
1.25"
1-1/2"
2,000
1.25"
1-1/2"
* Indicates Tufted Pattern brush. All others are Dense Pattern.
APPLICATIONS:
when using power
brushes.
20
Tanis Brush
(800) 234-7002 | (262) 646-9000
Abrasive Brushes
CERAMIX® MINI DISC BRUSHES
CeramiX® contains 3M™ Company 321 mineral grain which provides enhanced cutting action up to 3-5 times greater than traditional abrasive filaments.
CeramiX® fractures in sharper, jagged surfaces for superior abrasion providing minimum cycle times, increased productivity and maximizes abrasive media
on part.
TANIS
BRUSH
PART NO.
DIAMETER
GRIT
FILAMENT
ARBOR
TRIM
MAX.
DIAMETER
HOLE
LENGTH
RPM
3/8”
1-1/4”
4,500
3/8”
1-1/4”
4,500
34580
120
.028
34585
80
.040
34590
120
.040
34592
80
.055
34595
80
.045x.090
34605
120
.028
34610
80
.040
120
.040
2"
3"
34615
34617
80
.055
34620
80
.045x.090
*Set screw included to securely mount drive arbor.
SILICON CARBIDE MINI DISC BRUSHES
Ideal for deburring or improving surface finish, these small-diameter disc brushes have a composite hub and feature a very high filament density. Silicon
carbide filament in rectangular shape is shown in the photo below.
TANIS
BRUSH
PART NO.
DIAMETER
GRIT
FILAMENT
ARBOR
TRIM
MAX.
DIAMETER
HOLE
LENGTH
RPM
3/8”
1-1/4”
4,500
3/8”
1-1/4”
4,500
34630
120
.022
34635
80
.040
120
.040
34645
80
.045x.090
34650
120
.022
2"
34640
34655
3"
34660
34665
80
.040
120
.040
80
.045x.090
*Set screw included to securely mount drive arbor.
MINI DISC BRUSH DRIVE ARBOR
Used to securely mount mini disc brushes for use in any type of military machine or CNC machine. Drive arbor shaft is 1/2” diameter for use in any live tool
holder. Set screw included in each brush to secure brush to drive arbor.
TANIS
BRUSH
SHAFT
MAX.
PART NO.
DIAMETER
DIAMETER
RPM
35048
2" & 3”
1/2”
4,500
www.tanisbrush.com
[email protected]
Made in USA
21
Abrasive Brushes
CERAMIX® END BRUSHES
CeramiX® end brushes feature an integrated stem that allows mounting in a collet or tool holder for CNC machine or robotic use. End brushes can also be used
in portable air or electric tools. End brushes are a great choice for deburring slots, small recessed areas and internal part features. CeramiX® end brushes are
able to deliver a targeted brushing action to small areas on machined parts to blend end-mill tool marks, deburr and blend rough edges and provide ideal surface
finish.
TANIS
PART NO.
35700
35705
35710
35715
35720
35725
35730
35735
35740
BRUSH
DIAMETER
1/2”
3/4”
1”
GRIT
120
180
220
120
180
220
120
180
220
FILAMENT
DIAMETER
.040
.035
.022
.040
.035
.022
.040
.035
.022
TRIM
LENGTH
OVERALL
LENGTH
STEM
DIAMETER
MAX
RPM
1”
2-3/4”
1/4”
10,000
1”
2-3/4”
1/4”
10,000
1”
2-3/4”
1/4”
10,000
SILICON CARBIDE END BRUSHES
Silicon Carbide end brushes feature an integrated stem that allows mounting in a collet or tool holder for CNC machine or robotic use. End brushes can also be
used in portable air or electric tools. End brushes are a great choice for deburring slots, small recessed areas and internal part features.
TANIS
PART NO.
35745
35750
35755
35760
35765
35770
35775
35780
35785
22
Tanis Brush
BRUSH
DIAMETER
1/2”
3/4”
1”
GRIT
120
180
320
120
180
320
120
180
320
FILAMENT
DIAMETER
.040
.035
.022
.040
.035
.022
.040
.035
.022
(800) 234-7002 | (262) 646-9000
TRIM
LENGTH
OVERALL
LENGTH
STEM
DIAMETER
MAX
RPM
1”
2-3/4”
1/4”
10,000
1”
2-3/4”
1/4”
10,000
1”
2-3/4”
1/4”
10,000
Abrasive Brushes
CERAMIX® STEM MOUNTED END BRUSHES
The integrated stem allows for convenient mounting in a collet or toolholder, these smaller diameter disc brushes are a great choice for deburring slots or
small recessed areas, as well as reaching into internal part features. For more information on CeramiX® filament, see the Technical section.
TANIS
BRUSH
PART NO.
DIAMETER
GRIT
FILAMENT
STEM
TRIM
MAX.
DIAMETER
DIAMETER
LENGTH
RPM
1/4"
1-3/8"
4,500
1/4"
1-3/8"
4,500
1/4"
1-3/8"
4,500
32285
80
32287
80
.055
32290
80
.045 X .090
120
.040
32300
120
.028
32305
220
.022
32310
80
.040
32312
80
.055
32295
32315
1-1/2"
.040
80
.045 X .090
120
.040
32325
120
.028
32330
220
.022
32335
80
.040
32337
80
.055
32340
80
.045 X .090
120
.040
32350
120
.028
32355
220
.022
32320
32345
2"
2-1/2"
SILICON CARBIDE STEM MOUNTED END BRUSHES
Smaller diameter disc brushes for deburring slots or small recessed areas, as well as reaching into internal part features. The integrated stem allows for
convenient mounting in a collet or toolholder. Silicon carbide filament is available in a number of grit and diameter options.
TANIS
BRUSH
PART NO.
DIAMETER
GRIT
FILAMENT
STEM
TRIM
MAX.
DIAMETER
DIAMETER
LENGTH
RPM
1/4"
1-3/8"
4,500
1/4"
1-3/8"
4,500
1/4"
1-3/8"
4,500
32210
80
.040
32215
80
.045 X .090
32220
120
.040
32225
120
.022
32230
320
.022
32235
80
.040
32240
80
.045 X .090
32245
1-1/2"
120
.040
32250
120
.022
32255
320
.022
32260
80
.040
32265
80
.045 X .090
120
.040
32275
120
.022
32280
320
.022
32270
2"
2-1/2"
www.tanisbrush.com
[email protected]
Made in USA
23
Abrasive Brushes
FINE BLANKING DISC BRUSHES
Designed for stationary finishing machines, Tanis abrasive nylon fine-blanking disc brushes fit European machines including Volbhag, Niederberger
and Peter Wolters. Fine-blanking disc brushes are ideal for deburring and edge radiusing on fine-blanked parts, and polishing machined surfaces.
CeramiX®
TANIS
BRUSH
PART NO.
DIAMETER
32120
32130
32140
32150
32160
32170
32180
32190
GRIT
FILAMENT
TRIM
ARBOR
BLOCK
MAX.
DIAMETER
LENGTH (mm)
HOLE (mm)
THICKNESS
RPM
25
1”
3,000
6”
80
.040
6”
120
.040
6”
180
.035
6”
220
.022
25
36
25
36
25
36
25
36
Silicon Carbide
TANIS
BRUSH
PART NO.
DIAMETER
32010
6”
32020
32030
32040
32050
32060
32070
APPLICATIONS:
• Machine surfaces
• Deburring fineblanked parts
32080
32090
32100
32110
FILAMENT
TRIM
ARBOR
BLOCK
MAX.
DIAMETER
LENGTH (mm)
HOLE (mm)
THICKNESS
RPM
46
.060
25
6”
60
.045
6”
80
.050
6”
120
.040
25
1”
3,000
6”
180
.035
6”
320
.022
GRIT
25
36
25
36
25
36
25
36
25
36
• Radiusing stamped parts
• Honing aluminum extrusions
when using wire
brushes.
24
Tanis Brush
(800) 234-7002 | (262) 646-9000
Abrasive Brushes
Technical Information - Twisted Brushes
Twisted Brush Stem Constructions:
Single stem, single spiral - Filament is twisted between two stem wires with a single layer of filament.
Double stem, single spiral - Filament is twisted between four stem wires, with two stem wires on each
side for additional strength and higher density fill.
Double stem, double spiral - Filament is twisted between four stem wires with two layers of bristles.
Each layer is perpendicular to the other with a single stem wire in each quadrant. The highest brush
density and highest strength twisted wire brush available.
Brush Tip Styles:
Continuous end
Cut-off end
Operating Recommendations:
When mounting a twisted brush in a collet or chuck, it is recommended
to minimize the overhang of the stem to under an inch. This is particularly
true with power tube brushes, and it is important to avoid any load conditions and operating speeds that can cause stem deflections and destructive bending. A safe operating speed from 100 - 500 RPM is recommended for most twisted brushes.
Twist Brush Terminology:
To reach into deeper holes we recommend the use of collet-ready shank
mounted brushes or drill extension rods rather than increasing stem
overhang.
Before Starting the Twist Brush Rotation:
• Secure the brush in the chuck.
• Ensure clockwise brush rotation - counter clockwise rotation
can cause the brush to come apart and release the filament.
• Securely clamp the workpiece. Make sure all machine guards are in position.
• Align the brush with the workpiece to ensure the brush rotates on its true
centerline, and avoiding stem deflection.
• Guide the brush into the hole before starting the brush rotation.
• Always wear eye protection and protective clothing!
www.tanisbrush.com
[email protected]
Made in USA
25
Abrasive Brushes
ABRASIVE NYLON MICRO TWISTED BRUSHES
Microabrasive tube brushes are ideal for ultra-fine deburring of internal holes produced by small diameter drilling. Light deburring and cleaning will not alter
bore dimensions or surface finishes. Microabrasive tube brushes are used in power tools to create a side-wiping action, or used manually.
Alumina Silicate
TANIS
PART NO.
BRUSH
DIAMETER
GRIT
FILAMENT
DIAMETER
BRUSH
LENGTH
OVERALL
LENGTH
STEM
DIAMETER
31210
.030”
2000
.008
1/2”
4”
.015
.031”
1/32
0.787
31215
.050”
.022
.047”
3/64
1.191
1.588
2000
31220
.075”
.033
.063”
1/16
.090”
.041
.078”
5/64
1.984
31230
.105”
.041
.094”
3/32
2.381
2.778
2000
.008
4”
31235
.125”
.064
.109”
7/64
31240
.135”
.075
.125”
1/8
3.175
31245
.150”
.075
.141”
9/64
3.572
31250
.165”
.087
.156”
5/32
3.969
31255
.180”
.087
.172’
11/64
4.366
4”
31260
.190”
.087
.188’
3/16
4.736
.215”
.087
.203”
13/64
5.159
31270
.230”
.087
.219”
7/32
5.556
31275
.245”
.260”
31285
.325”
2000
.008
1”
31265
31280
2000
.008
3/4”
FOR HOLE DIAMETERS
INCH
FRACT
MM
31225
Aluminum Oxide
26
Single stem, single spiral; cut off end
.008
1”
5”
1”
5”
.115
.234”
15/64
5.953
.115
.250”
1/4
6.350
.115
.313”
5/16
7.938
Single stem, single spiral; continuous end
TANIS
PART NO.
BRUSH
DIAMETER
31140
.165”
.156”
5/32
31145
.180”
.172”
11/64
4.366
31150
.190”
.188”
3/16
4.736
5.159
GRIT
600
FILAMENT
DIAMETER
.012
BRUSH
LENGTH
OVERALL
LENGTH
1”
5”
STEM
DIAMETER
.087
FOR HOLE DIAMETERS
INCH
FRACT
MM
3.969
31155
.215”
.203”
13/64
31160
.230”
.219”
7/32
5.556
31165
.245”
.234”
15/64
5.953
.250”
1/4
6.350
.313”
5/16
7.938
31170
.260”
31175
.325”
600
.012
1”
5”
.115
31180
.385”
600
.012
1”
5”
.147
.375”
3/8
9.525
31185
.515”
600
.012
1”
5”
.168
.500”
1/2
12.70
31190
.640”
.625”
5/8
15.87
31195
.765”
31200
.890”
31205
1.015”
Tanis Brush
600
600
.012
.012
1”
1”
(800) 234-7002 | (262) 646-9000
5”
5”
.221
.248
.750”
3/4
19.05
.875”
7/8
22.225
1”
1
25.40
Abrasive Brushes
ABRASIVE NYLON MICRO TWISTED BRUSHES
Microabrasive tube brushes are ideal for ultra-fine deburring of internal holes produced by small diameter drilling. Light deburring and cleaning will not
alter bore dimensions or surface finishes. Microabrasive tube brushes are used in power tools to create a side-wiping action, or used manually.
Silicon Carbide
TANIS
PART NO.
BRUSH
DIAMETER
31040*
.050”
31045*
.075”
31050*
.090”
31055*
.105”
31060*
.125”
31065*
.135”
Single stem, single spiral; cut off or continuous end.
GRIT
FILAMENT
DIAMETER
500
.018
BRUSH
LENGTH
OVERALL
LENGTH
STEM
DIAMETER
.022
.047”
3/64
1.191
4”
.033
.063”
1/16
1.588
.041
.078”
5/64
1.984
1/2”
3/4”
3/4”
500
.018
1”
4”
FOR HOLE DIAMETERS
INCH
FRACT
MM
.041
.094”
3/32
2.381
.064
.109”
7/64
2.778
.075
.125”
1/8
3.175
31070*
.150”
.075
.141”
9/64
3.572
31075
.165”
.087
.156”
5/32
3.969
31080
.180”
.087
.172”
11/64
4.366
31085
.190”
.087
.188”
3/16
4.736
31090
.215”
.087
.203”
13/64
5.159
500
.018
1”
5”
31095
.230”
.087
.219”
7/32
5.556
31100
.245”
.115
.234”
15/64
5.953
31105
.260”
.115
.250”
1/4
6.35
31110
.325”
31005
.385”
31115
31010
.515”
31120
31015
.640”
31125
31020
.765”
31130
31025
.890”
31135
31030
31035
1.015”
320
.022
500
.018
320
.022
500
.018
320
.022
500
.018
320
.022
500
.018
320
.022
500
.018
320
.022
500
.018
.115
.313”
5/16
7.938
1”
5”
.147
.375”
3/8
9.525
1”
5”
.168
.500”
1/2
12.70
1”
5”
.168
.625”
5/8
15.87
1”
5”
.221
.750”
3/4
19.05
1”
5”
.221
.875”
7/8
22.225
1”
5’
.248
1”
1
25.40
*All brushes have cut off or continuous end.
when using power
brushes.
www.tanisbrush.com
[email protected]
Made in USA
27
Abrasive Brushes
ABRASIVE NYLON COLLET READY BRUSHES
Ideal for internal deburring and finishing applications, tubular component parts and drilled and tapered holes. These power tube brushes are fitted with a solid
galvanized steel shank for ease of use in CNC machine tools, drill presses and manual machine tools.
CeramiX
TANIS
PART NO.
34820
34825
34827
34829
34830
34835
34840
34845
34850
34855
34860
34865
34867
34869
34870
34875
34880
34885
34887
34889
34890
34895
34900
34905
34910
34915
®
BRUSH
DIAMETER
1/4"
5/16”
3/8"
1/2"
5/8"
3/4"
7/8”
1"
1-1/4"
1-3/8”
1-1/2"
1-3/4"
2"
180
120
180
120
FILAMENT
DIAMETER
.035
.028
.035
.028
180
120
180
120
180
120
180
120
180
120
120
80
120
80
120
80
120
80
120
80
120
80
.035
.028
.035
.040
.035
.040
.035
.040
.035
.040
.040
.040
.040
.040
.040
.040
.040
.040
.040
.040
.040
.040
GRIT
BRUSH
LENGTH
OVERALL
LENGTH
2"
8"
2”
8”
2"
8"
2"
8"
2"
8"
2"
8"
2”
8”
2"
8"
2"
8"
2”
8”
2"
8"
2"
8"
2"
8"
SHANK
DIAMETER
3/16"
1/4"
when using power
brushes.
28
Tanis Brush
(800) 234-7002 | (262) 646-9000
Abrasive Brushes
ABRASIVE NYLON COLLET READY BRUSHES
Ideal for internal deburring and finishing applications, tubular component parts and drilled and tapered holes. These power tube brushes are fitted with a solid
galvanized steel shank for ease of use in CNC machine tools, drill presses and manual machine tools.
Silicon Carbide
TANIS
PART NO.
34920
34925
34927
34929
34930
34935
34940
34945
34950
34955
34960
34965
34967
34969
34970
34975
34980
34985
34987
34989
34990
34995
35000
35006
35011
35016
BRUSH
DIAMETER
1/4"
5/16”
3/8"
1/2"
5/8"
3/4"
7/8”
1"
1-1/4"
1-3/8”
1-1/2”
1-3/4”
2”
180
120
180
120
FILAMENT
DIAMETER
.035
.022
.035
.022
180
120
180
120
180
120
180
120
180
120
120
80
120
80
120
80
120
80
120
80
120
80
.035
.022
.035
.040
.035
.040
.035
.040
.035
.040
.040
.040
.040
.040
.040
.040
.040
.040
.040
.040
.040
.040
GRIT
www.tanisbrush.com
BRUSH
LENGTH
OVERALL
LENGTH
2"
8"
2”
8”
2"
8"
2"
8"
2"
8"
2"
8"
2”
8”
2"
8"
2"
8"
2”
8”
2"
8"
2"
8"
2"
8"
SHANK
DIAMETER
3/16"
[email protected]
1/4"
Made in USA
29
Abrasive Brushes
ABRASIVE NYLON TUBE BRUSHES
Abrasive tube brushes are suited for cleaning and cutting action in a variety of industrial applications. Deburring action will not alter the part bore dimensions or
disturb delicate surface finishes. Tube brushes can be used in a dry or wet application for metallic or non-metallic parts.
®
CeramiX
TANIS
PART NO.
31820
31785
31825
31790
31835
31800
31740
31840
31805
31745
31850
31815
31705
31855
31755
31710
31865
31765
31720
31870
31770
31725
31875
31775
31730
31880
31780
31735
Double stem, single spiral; cut off end. Galvanized stem wire.
BRUSH
DIAMETER
1/4”
3/8”
1/2”
5/8”
3/4”
1”
1-1/4”
1-1/2”
1-3/4”
2”
220
180
220
180
220
180
120
220
180
120
FILAMENT
DIAMETER
.022
.035
.022
.035
.022
.035
.040
.022
.035
.040
220
180
80
220
120
80
220
120
80
220
120
80
220
120
80
220
120
80
.022
.035
.040
.022
.040
.040
.022
.040
.040
.022
.040
.040
.022
.040
.040
.022
.040
.040
GRIT
when using power
brushes.
30
Tanis Brush
(800) 234-7002 | (262) 646-9000
BRUSH
LENGTH
2”
OVERALL
LENGTH
5”
STEM
DIAMETER
1/8”
2”
5”
1/8”
2”
5”
5/32”
2”
5”
7/32”
2-1/2”
5-1/2”
2-1/2”
5-1/2”
2-1/2”
5-1/2”
1/4”
2-1/2”
5-1/2”
2-1/2”
5-1/2”
2-1/2”
5-1/2”
Abrasive Brushes
Aluminum Oxide
TANIS
PART NO.
31500
31515
31535
31555
BRUSH
DIAMETER
1/4”
3/8”
1/2”
5/8”
31580
31600
31640
31660
31680
31700
3/4”
1”
1-1/4”
1-1/2”
1-3/4”
2”
Silicon Carbide
TANIS
PART NO.
31490
31495
31505
31510
31520
31525
31530
31540
31545
31550
31565
31570
31575
31585
31590
31595
31625
31630
31635
31645
31650
31655
31665
31670
31675
31685
31690
31695
3/8”
1/2”
5/8”
3/4”
1”
1-1/4”
1-1/2”
1-3/4”
2”
600
600
FILAMENT
DIAMETER
.012
.012
BRUSH
LENGTH
2”
2”
OVERALL
LENGTH
4”
5”
600
.012
2”
5”
600
.012
2-1/2”
5-1/2”
GRIT
STEM
DIAMETER
1/8”
1/8”
5/32”
7/32”
1/4”
600
.012
2-1/2”
5-1/2”
BRUSH
DIAMETER
1/4”
320
180
320
180
320
180
120
320
180
120
FILAMENT
DIAMETER
.022
.035
.022
.035
.022
.035
.040
.022
.035
.040
320
180
80
320
120
80
320
120
80
320
120
80
320
120
80
320
120
80
.022
.035
.040
.022
.040
.040
.022
.040
.040
.022
.040
.040
.022
.040
.040
.022
.040
.040
GRIT
www.tanisbrush.com
BRUSH
LENGTH
OVERALL
LENGTH
STEM
DIAMETER
2”
5”
1/8”
2”
5”
1/8”
2”
5”
5/32”
2”
5”
7/32”
2-1/2”
5-1/2”
2-1/2”
5-1/2”
2-1/2”
5-1/2”
1/4”
2-1/2”
5-1/2”
2-1/2”
5-1/2”
2-1/2”
5-1/2”
[email protected]
Made in USA
31
Abrasive Brushes
ABRASIVE NYLON BURR BRUSHES
Abrasive burr brushes provide a high filament concentration for heavy burr removal. Burr brushes can be used in wet or dry applications and are ideal for
reducing cycle times in cross-hole deburring, cleaning threads, debris removal from blocks or machined blocks, crankshaft bores, and general deburring.
CeramiX
TANIS
PART NO.
31435
31390
31440
31395
31445
31400
31450
31405
31455
31410
31460
31415
31465
31420
31470
31425
31475
31430
31480
31485
32
Tanis Brush
®
BRUSH
DIAMETER
1/4”
3/8”
1/2”
5/8”
3/4”
1”
1-1/4”
1-1/2”
1-3/4”
2”
FILAMENT
BRUSH
OVERALL
STEM
LENGTH
LENGTH
DIAMETER
220
120
DIAMETER
.022
.040
1”
3-1/2”
1/8”
220
120
220
120
220
120
220
120
.022
.040
.022
.040
.022
.040
.022
.040
1”
3-1/2”
1”
3-1/2”
1”
3-1/2”
1”
3-1/2”
220
120
220
120
220
120
220
120
220
120
.022
.040
.022
.040
.022
.040
.022
.040
.022
.040
1”
3-1/2”
1”
3-1/2”
1”
3-1/2”
1”
3-1/2”
1”
3-1/2”
GRIT
(800) 234-7002 | (262) 646-9000
3/16”
1/4”
Abrasive Brushes
Silicon Carbide
Single stem, single spiral; continuous end.
TANIS
BRUSH
PART NO.
DIAMETER
31290
31295
1/4”
120
3/8”
120
1/2”
120
5/8”
120
3/4”
120
1”
120
1-1/4”
120
1-1/2”
120
1-3/4”
120
2”
120
31300
31305
31310
31315
31320
31325
31330
31335
31340
31345
31350
31355
31360
31365
31370
31375
31380
31385
GRIT
FILAMENT
BRUSH
OVERALL
STEM
DIAMETER
LENGTH
LENGTH
DIAMETER
.022
.040
1”
3-1/2”
1/8”
1”
3-1/2”
1”
3-1/2”
1”
3-1/2”
1”
3-1/2”
1”
3-1/2”
1”
3-1/2”
1”
3-1/2”
1”
3-1/2”
1”
3-1/2”
.022
.040
.022
.040
.022
.040
.022
.040
.022
.040
.022
.040
.022
.040
.022
.040
.022
.040
3/16”
1/4”
when using power
brushes.
www.tanisbrush.com
[email protected]
Made in USA
33
Twisted Brushes
POWER FITTING BURR BRUSHES
An ideal option for quick cleaning of fittings, tubing, drill holes and other deburring applications. The 1/4” hex shank provides greater strength for use in
power drills and presses. Recommended operating speed is 100-600 RPM; maximum safe free speed is 2000 RPM. Always run power brushes in a
clockwise rotation.
CARBON
STAINLESS
BRUSH
BRUSH
OVERALL
FILAMENT
STEEL
STEEL
LELNGTH
LENGTH
DIAMETER
06760
06761
06762
06763
06764
06765
06766
06770
06771
06772
06773
06774
06775
06776
DIAMETER
3/8”
1/2”
5/8”
3/4”
7/8”
1”
1-1/8”
3/4”
2-1/2”
.006
HEAVY DUTY POWER BURR BRUSH
Used in drill presses and hand power tools for deburring, polishing and cleaning inner bores of tubing, machined cylinders, flat stock and smooth or
threaded blind holes. Single stem, single spiral configuration with continuous end.
H/C
STAINLESS
STEEL
STEEL
BRASS
06200
06201
06202
06205
06206
06207
06225
06226
06227
06235
06236
06237
06255
06256
06257
06260
06261
06262
06290
06291
06292
06320
06321
06322
06330
06331
06332
06380
06381
06382
06390
06391
06392
06445
06446
06447
06450
06451
06452
06505
06506
06507
06510
06511
06512
06565
06566
06567
06570
06571
06572
06605
06606
06635
06636
BRUSH
BRUSH
OVERALL
STEM
FILAMENT
DIAMETER
LENGTH
LENGTH
DIAMETER
DIAMETER
1/4”
1”
3-1/2”
.113
5/16”
1”
3-1/2”
.113
3/8”
1”
3-1/2”
.113
7/16”
1”
3-1/2”
.113
1/2”
5/8”
Tanis Brush
1”
3-1/2”
3-1/2”
.168
.168
3/4”
1”
3-1/2”
.220
7/8”
1”
3-1/2”
.220
.004
.003
.005
.004
.005
.005
.005
.008
.005
.008
.006
.008
.006
.008
.006
1”
1”
3-1/2”
.248
06607
1-1/8”
1”
3-1/2”
.248
.008
06637
1-1/4”
1”
3-1/2”
.248
.008
protective clothing when
using power brushes.
34
1”
.003
(800) 234-7002 | (262) 646-9000
.008
Twisted Brushes
POWER TUBE BRUSHES
For polishing, blending, burr removal, and cleaning. For use in power tools where heavy-duty cleaning is required.
H/C
STAINLESS
BRUSH
BRUSH
OVERALL
STEM
FILAMENT
STEEL
STEEL
BRASS
DIAMETER
LENGTH
LENGTH
DIAMETER
DIAMETER
05205
05206
05207
1/4”
1-1/2”
4”
.095
.005
05215
05216
05217
5/16”
1-1/2”
4”
.125
.005
05225
05226
05227
3/8”
1-1/2”
4”
.125
05240
05241
05242
05245
05246
05247
05260
05261
05262
05265
05266
05267
05280
05281
05282
05285
05286
05287
05300
05301
05302
05305
05306
05307
05320
05321
05322
05325
05326
05327
1/2”
2”
5”
.162
5/8”
2”
5”
.208
3/4”
2-1/2”
5-1/2”
.237
7/8”
2-1/2”
5-1/2”
.237
1”
2-1/2”
5-1/2”
.237
.005
.004
.006
.005
.008
.006
.010
.006
.010
.006
.010
SIDE TUFT CLEANING BRUSH
For cleaning and polishing threads, inner walls of tubes and cylinders. Solid concentration of bristles provides a high degree of bristle stiffness with little
flexing of bristles during operation. For use in power tools. Use holder to run at a higher RPM.
H/C
STAINLESS
STEEL
STEEL
BRASS
BRUSH
BRUSH
OVERALL
STEM
FILAMENT
DIAMETER
LENGTH
LENGTH
DIAMETER
DIAMETER
1/4”
9/16”
2-1/8”
.099
05700
05701
05702
05705
05706
05707
05720
05721
05722
5/16”
05740
05741
05742
3/8”
05745
05746
05747
3/8”
05775
05776
05777
7/16”
05805
05806
05807
05810
05811
05812
05870
05871
05872
5/8”
05885
05886
05887
3/4”
05890
05891
05892
3/4”
05900
05901
05902
7/8”
05930
05931
05932
05935
05936
05937
9/16”
1/2”
2-1/8”
.099
9/16”
2-1/8”
.099
9/16”
2-1/8”
.099
5/8”
5/8”
1”
5/8”
2-1/4”
2-1/4”
2-1/4”
.150
.150
.150
.003
.005
.003
.003
.005
.005
.005
.008
.005
.005
.008
.005
.005
.008
SIDE TUFT BRUSH HOLDER
Slightly reduces bristle trim length for more aggressive brush action while allowing the brush to be driven at a higher RPM.
PART
STEM
OVERALL
SHANK
NUMBER
DIAMETER
LENGTH
DIAMETER
01040
3/32”
3-3/8”
1/4” for .099 stem diameter
01041
1/4”
3-3/8”
1/4” for .150 stem diameter
www.tanisbrush.com
[email protected]
Made in USA
35
Twisted Brushes
HAND HELD HEAVY DUTY TUBE BRUSH
Long stem, for polishing, blending, burr removal, and cleaning in hard to reach areas. For manual or hand applications where heavy-duty
cleaning is required.
H/C
STAINLESS
BRUSH
BRUSH
OVERALL
STEM
FILAMENT
LENGTH
STEEL
STEEL
BRASS
DIAMETER
LENGTH
DIAMETER
DIAMETER
05420
05440
05460
1/4”
1-1/2”
.107
.003
05421
05441
05461
3/8”
1-1/2”
.125
.005
05422
05442
05462
1/2”
2”
.162
.006
.208
.008
.237
.006
18”
05223
05443
05463
5/8”
2”
05424
05444
05464
3/4”
2-1/2”
05425
05445
05465
7/8”
2-1/2”
.237
.006
05426
05446
05466
1”
2-1/2”
.237
.006
HAND HELD HEAVY DUTY TUBE BRUSH
For polishing, blending, burr removal, and cleaning. Short stem, for manual or hand applications where heavy-duty cleaning is required.
36
H/C
STAINLESS
BRUSH
BRUSH
OVERALL
STEM
FILAMENT
STEEL
STEEL
BRASS
DIAMETER
LENGTH
LENGTH
DIAMETER
DIAMETER
05410
05430
05450
1/4”
1-1/2”
.107
.003
05411
05431
05451
3/8”
1-1/2”
.125
.005
05412
05432
05452
1/2”
2”
.162
.006
05413
05433
05453
5/8”
2”
.208
.008
05414
05434
05454
3/4”
2-1/2”
.237
.010
05415
05435
05455
7/8”
2-1/2”
.237
.010
05416
05436
05456
1”
2-1/2”
.237
.010
Tanis Brush
(800) 234-7002 | (262) 646-9000
5-1/2”
Twisted Brushes
HAND HELD TUBE CLEANING BRUSH
For manual or hand cleaning applications. Ideal for industrial cleaning.
Single stem single spiral tube brush with short handle and loop end
H/C
STAINLESS
ALL
BRUSH
BRUSH
OVERALL
STEM
FILAMENT
STEEL
STEEL
BRASS
ST/ST
DIAMETER
LENGTH
LENGTH
DIAMETER
DIAMETER
05000
05010
05001
05002
05003
1/8”
1”
6”
.088
05011
05012
05013
05015
05016
05017
05018
05020
05021
05022
05023
05025
05026
05027
05028
05035
05036
05037
05038
05040
05041
05042
05043
05045
05046
05047
05048
05055
05056
05057
05058
05060
05061
05062
05063
05065
05066
05067
05068
3/16”
1-1/2”
7”
.088
.003
.003
.005
.003
1/4”
1-1/2”
7”
.088
5/16”
1-1/2”
7”
.088
3/8”
2”
8”
.120
7/16”
2”
8”
.120
1/2”
2”
8”
.120
2-1/2”
9”
.150
.008
3”
10”
.172
.008
05075
05076
05077
05078
9/16”
05085
05086
05087
05088
5/8”
05095
05096
05097
05098
11/16”
05105
05106
05107
05108
3/4”
05115
05116
05117
05118
13/16”
05125
05126
05127
05128
7/8”
05135
05136
05137
05138
15/16”
05145
05146
05147
05148
1”
.005
.006
.004
.006
.006
.004
.006
Single stem single spiral tube brush with long handle and loop end
STAINLESS
ALL
BRUSH
BRUSH
OVERALL
STEM
FILAMENT
STEEL
BRASS
ST/ST
DIAMETER
LENGTH
LENGTH
DIAMETER
DIAMETER
08315
08345
08375
1/4”
3”
27”
.132
.005
08319
08349
08379
3/8”
3”
27”
.147
.005
08323
08353
08383
1/2”
3”
27”
.168
.006
27”
.194
.006
27”
.194
.008
08327
08357
08387
5/8”
3”
08331
08361
08391
3/4”
3”
08335
08365
08395
7/8”
3”
08339
08369
08399
1”
3”
www.tanisbrush.com
[email protected]
Made in USA
37
Twisted Brushes
MINIATURE AND MICRO MINIATURE BRUSHES
For ultra-fine cross hole deburring, cleaning, blending and polishing of small diameter holes.
Miniature brushes with loop for hand use Single stem, single spiral; with loop end
ST/ST
ALL
BRUSH
BRUSH
OVERALL
STEM
FILAMENT
w/GALV.STEM
ST/ST
BRASS
NYLON
DIAMETER
LENGTH
LENGTH
DIAMETER
DIAMETER
08780
05151
04980
05160
1/32
08781
05153
04982
05162
1/16
1/2”
4”
3/4”
4”
3/4”
4”
.062
.003
3/4”
4”
.062
.003
08782
05155
04984
05164
3/32
08783
05157
04986
05166
1/8
08784
05159
04988
05168
5/32
08785
05181
04990
05190
3/16
08786
05183
04992
05192
7/32
08787
05185
04994
05194
1/4
when using wire
brushes.
38
Tanis Brush
(800) 234-7002 | (262) 646-9000
.022
.032
.042
.062
.003
.003
Twisted Brushes
MINIATURE AND MICRO MINIATURE BRUSHES
For ultra-fine cross hole deburring, cleaning, blending and polishing of small diameter holes.
Miniature brushes, stainless steel stem and cut off end for power or hand use
Single stem, single spiral
BRUSH
BRUSH
OVERALL
STEM
FILAMENT
ST/ST
BRASS*
NYLON
DIAMETER
LENGTH
LENGTH
DIAMETER
DIAMETER
08130
08500
08170
1/50”
1/4”
4”
.012
.003
1/2”
4”
.022
08131
08501
08171
1/32”
08132
08502
08172
3/64”
08133
08504
08173
1/16”
.016
08134
08505
08174
5/64”
08135
08506
08175
3/32”
08136
08507
08176
7/64”
.056
08137
08508
08177
1/8”
.062
08138
08509
08178
9/64”
.062
08139
08510
08179
5/32”
08140
08511
08180
11/64”
08141
08512
08181
3/16”
.075
.032
3/4”
4”
.048
4”
.075
08142
08513
08182
13/64”
.087
08514
08183
7/32”
.095
08184
15/64”
.115
08515
08145
08516
08185
1/4”
08146
08517
08186
5/16”
.003
.075
1”
08143
08144
.003
.022
1”
4”
.115
.003
.003
.115
*Brass brushes are made with a 3” overall length.
Metric miniature diameter brushes with cut off end
ABRASIVE
NYLON*
ST/ST
BRASS**
BRUSH
BRUSH
OVERALL
STEM
FILAMENT
DIAMETER
LENGTH
LENGTH
DIAMETER
DIAMETER
5/8”
4”
08410
08430
08760
1.0 mm
08411
08431
08761
1.5 mm
08412
08432
08762
2.0 mm
08413
08433
08763
2.5 mm
.016
.022
3/4”
4”
.032
.042
08414
08434
08764
3.0 mm
.056
08415
08435
08765
3.5 mm
.062
08416
08436
08766
4.0 mm
08417
08437
08767
4.5 mm
08418
08438
08768
5.0 mm
.003
.003
.070
1”
4”
.087
.087
08419
08439
08769
5.5 mm
.115
08420
08440
08770
6.0 mm
.115
08421
08441
08771
6.5 mm
.115
.003
* Abrasive Nylon brushes are made with a .008 Silicate filament material.
** Brass brushes are made with a 3” overall length.
www.tanisbrush.com
[email protected]
Made in USA
39
Twisted Brushes
MINIATURE BRUSH SETS
For ultra-fine cross hole deburring, thread cleaning, blending and polishing of small diameter holes. Single-stem single-spiral construction, choice of filament.
Micro diameter set
TANIS
PART NO.
08030
08031
08032
FILAMENT
MATERIAL
Nylon
Stainless Steel
Brass
DIAMETERS
INCLUDED IN SET
.032, .040, .047, .063, .072, .094”
.040, .047, .063, .072, .094”
.040, .047, .063, .072, .094”
Brushes have stainless steel stems, brush parts are 1/2” to 3/4”, and overall lengths are 4”.
Thread diameter set
TANIS
PART NO.
08040
08041
08042
FILAMENT
MATERIAL
Stainless Steel
Nylon
Brass
DIAMETERS
INCLUDED IN SET
#0, #2, #4, #6, #8, #10, 1/4”,
5/16”, 3/8”, 1/2”, 3/4”
Brushes have stainless steel stems, brush parts are 3/4” to 1-1/2”, and overall
lengths are 4” to 6”
Tube diameter set
TANIS
PART NO.
08050
08051
08052
FILAMENT
MATERIAL
Brass
Nylon
Stainless Steel
DIAMETERS
INCLUDED IN SET
1/8”, 1/4”, 3/8”, 1/2”
Brush parts are 1-1/2” to 2”, and overall length is 8”.
when using wire
brushes.
40
Tanis Brush
(800) 234-7002 | (262) 646-9000
Twisted Brushes
For manual or hand cleaning applications. Ideal for industrial cleaning.
Cut Off Tip - Black Nylon
TANIS
PART NO.
06030
06100
06031
06101
06700
06032
06102
06133
06033
06034
06173
06035
06036
06037
BRUSH
DIAMETER
1/2
BRUSH
LENGTH
2”
4”
2”
4”
1-1/2”
3”
4”
3/4”
3”
1”
4”
1-1/4”
4”
1-1/2”
2”
4”
5”
1/4”
3/8”
1/2”
OVERALL
LENGTH
6-1/4”
26”
6-1/4”
26”
7-1/2”
8-1/2”
26”
8-1/2”
8-1/2”
12-1/4”
FILAMENT
DIAMETER
.008
.006
.008
.008
.010
.012
.010
.006
.012
.014
12”
13”
13”
16-3/4”
.020
.014
.014
.014
Cut Off Tip - Horse Hair
TANIS
PART NO.
06005
06680
06081
06006
06681
06007
06682
06083
06085
06086
06011
BRUSH
DIAMETER
1/4”
5/16”
3/8”
1/2”
3/4”
1”
1-1/4”
2”
www.tanisbrush.com
BRUSH
LENGTH
2”
4”
1-1/2”
2”
4”
3”
4”
3”
4”
4”
5”
OVERALL
LENGTH
6-1/4”
26”
9”
6-1/4”
26”
8-1/2”
26”
8-3/4”
12-1/4”
13”
16”
[email protected]
Made in USA
41
Twisted Brushes
For internal cleaning in industrial, laboratory, and food service industries. Brushes are made with single-stem single-spiral construction.
Cut Off Tip - Nylon and Horse Hair with tapered brush diameters
TANIS
PART NO.
06705
06710
BRUSH
DIAMETER
BRUSH
LENGTH
OVERALL
LENGTH
3/4” - 1-1/4”
5”
12”
FILAMENT
MATERIAL
Horse Hair
.010 Black Nylon
Cut Off Tip - Nylon and Horse Hair with long handle
TANIS
PART NO.
06688
06689
06690
06082
06691
06692
06693
06694
06695
06706
06708
06697
06696
06698
42
Tanis Brush
BRUSH
DIAMETER
1/2”
3/4”
1/2”
3/4”
BRUSH
LENGTH
OVERALL
LENGTH
4-1/2”
42”
4-1/2”
42”
5/8”
4-1/2”
42”
1”
4-1/2”
40-1/2”
1-1/4”
4-1/2”
40-1/2”
1-1/2”
4-1/2”
40-1/2”
2”
4-1/2”
40-1/2”
(800) 234-7002 | (262) 646-9000
FILAMENT
MATERIAL
.010 Black Nylon
.008 Black Nylon
Horse Hair
Horse Hair
.012 Black Nylon
Horse Hair
.014 Black Nylon
.010 Black Nylon
Horse Hair
Horse Hair
.014 Black Nylon
Horse Hair
.014 Black Nylon
Laboratory Brushes
LABORATORY BRUSHES
For cleaning glass or plastic test tubes, centrifuge tubes, flasks, graduated cylinders, beakers, containers, burets, pipettes, vials, carboys and bottles. Select from
a variety of brushes to clean laboratory equipment.
Test Tube Brush -- White Bristle or Black Nylon with Nylon tied tip
TANIS
PART NO.
06108
06146
06147
BRUSH
DIAMETER
3/4”
1-1/2”
2-3/8”
BRUSH
LENGTH
3”
4-3/4”
5-1/4”
OVERALL
LENGTH
9”
12”
20”
FILL MATERIAL
White Bristle
.010 Black Nylon
.016 Black Nylon
Test Tube Brush -- Natural Bristle with sponge end
TANIS
PART NO.
06134
BRUSH
DIAMETER
1/2”
BRUSH
LENGTH
3-1/4”
OVERALL
LENGTH
6-1/4”
FILL MATERIAL
Natural Bristle
Test Tube Brush -- White Nylon with fan tip
TANIS
PART NO.
901767
BRUSH
DIAMETER
3/8” - 1/2”
BRUSH
LENGTH
3”
OVERALL
LENGTH
7”
FILL MATERIAL
.006 White Nylon
Burette Brush -- Natural Bristle with fan tip
TANIS
PART NO.
06177
06176
06178
BRUSH
DIAMETER
1/2”
3/4”
1-1/4”
BRUSH
LENGTH
3-1/4”
3-1/4”
5-1/4”
OVERALL
LENGTH
30”
36”
36”
www.tanisbrush.com
FILL MATERIAL
Natural Bristle
Natural Bristle
Natural Bristle
[email protected]
Made in USA
43
Laboratory Brushes
Centrifuge Brush -- Natural Bristle with Black Nylon tuft
TANIS
PART NO.
06135
06136
BRUSH
DIAMETER
1” - 1-3/4”
3/4” - 1-1/2”
BRUSH
LENGTH
3”
4-1/2”
OVERALL
LENGTH
9”
12”
FILL MATERIAL
Natural Bristle
Natural Bristle
Pipette Brush -- Natural Nylon
TANIS
PART NO.
06158
BRUSH
DIAMETER
1/4” - 3/4”
BRUSH
LENGTH
7-1/2”
OVERALL
LENGTH
17”
FILL MATERIAL
.006 Natural Nylon
Babcock Milk Bottle Brush - Black Bristle with fan tip
TANIS
PART NO.
06143
BRUSH
DIAMETER
1-1/2” - 1/4”
BRUSH
LENGTH
3-1/4”
OVERALL
LENGTH
9”
FILL MATERIAL
Black Bristle
Volumetric Flask Brush -- Natural Bristle with plastic handle
TANIS
PART NO.
06184
06185
06186
44
Tanis Brush
BRUSH
DIAMETER
1-3/8”
1-1/2”
1-3/4”
BRUSH
LENGTH
3-1/2”
4”
5”
(800) 234-7002 | (262) 646-9000
OVERALL
LENGTH
12”
14”
17”
FILL MATERIAL
Natural Bristle
Natural Bristle
Natural Bristle
Laboratory Brushes
Beaker, Jar and Cylinder Brush - Black Bristle with tufted end
TANIS
PART NO.
06179
06180*
BRUSH
DIAMETER
2-3/8”
3”
BRUSH
LENGTH
6” (2 rows)
6” (4 rows)
OVERALL
LENGTH
16”
16”
FILL MATERIAL
Black Bristle
Black Bristle
* No tufted end
Graduate, Cylinder or Funnel Brush - Black Bristle with double tufted end
TANIS
PART NO.
06149
06148
BRUSH
DIAMETER
2-1/2”
2-1/2
BRUSH
LENGTH
4-1/2”
6”
OVERALL
LENGTH
9”
13”
FILL MATERIAL
Black Bristle
Black Bristle
Beaker Brush -- Nylon and Horse Hair
Filling materials are tightly wound onto spiral grooves with rust-resistant wire. Brush head has 1” diameter tuft at tip.
TANIS
PART NO.
06181
06182
06183
BRUSH
DIAMETER
2-1/2”
3”
2-3/8 - 2-7/8”
BRUSH
LENGTH
6”
6”
6”
OVERALL
LENGTH
16”
16”
16”
FILL MATERIAL
Black Nylon
Horse Hair
White Nylon
Flask or Nurse Bottle Brush -- Black Bristle with double tufted end
TANIS
PART NO.
06187
06188
BRUSH
DIAMETER
1-1/2”
1-3/4”
BRUSH
LENGTH
4-1/2”
4-1/2”
OVERALL
LENGTH
12”
16”
www.tanisbrush.com
FILL MATERIAL
Black Bristle
Black Bristle
[email protected]
Made in USA
45
#10 backing, 6” trim
#2-1/2 backing, 1” trim
Tanis Strip Brush
Capabilities
Tanis is an industry leader in strip brushes and stapled set strip brushes as well. There are five standard backing sizes available in
galvanized or stainless steel. Tanis strip brushes are offered with an array of filament materials including nylon, polyester, anti-static
nylon, metal detectable nylon, PTFE, horse hair, stainless steel and brass. Tanis has an unmatched selection of standard strip
brushes in a variety of sizes, shapes, filament material and overall lengths to meet your immediate need.
Flexible thermoset plastic and rigid PVC backings are available in our stapled set strip brushes. Our flexible stapled strip products
are available in different profile configurations in 3-foot and 6-foot lengths as well as continuous rolls for you to cut to your desired
length. Rigid PVC products are available in 3-foot and 6-foot lengths in different profiles and sizes.
Tanis has an unmatched selection of standard strip and stapled strip brushes in a variety of sizes, shapes, filament material and overall
lengths to meet your immediate need. Visit our website at www.tanisbrush.com to see a complete listing of standard products.
Power Brushes
COPPER CENTER CRIMPED WIRE WHEELS
For cleaning, deburring, finishing or roughening hard to reach areas. Fixed or adaptable arbor sizes to fit your spindle. Wheels are balanced to prevent vibration
and made with an internal solid steel ring. They can be used individually or mounted side-by-side for a wider brush face. Suggested applications: edge blending,
appearance finishing, cleaning and polishing internal or external tube diameter surfaces and thread cleaning. Maximum safe running speed is 20,000 RPM.
Carbon Steel
48
TANIS
BRUSH
FILAMENT
ARBOR
FACE
TRIM
MAX
PART NO.
10105
10110
10120
10125
10145
10150
10155
10165
10185
10190
10195
10200
10205
10215
10235
10240
10245
10250
10255
10260
10265
10270
10295
10300
10310
10320
10325
10330
10335
10340
10345
10350
10355
10360
10365
10370
10380
10385
10390
10395
DIAMETER
1”
1-1/4”
DIAMETER
.006
.006
.006
.008
.006
.008
.0104
.008
.006
.008
.0104
.0118
.014
.008
.006
.008
.0104
.0118
.014
.008
.0104
.0118
.0118
.014
.0118
.006
.008
.0104
.0118
.014
.006
.008
.0118
.014
.006
.008
.0118
.014
.006
.0118
HOLE
1/4”
1/4”
WIDTH
11/64”
3/16”
LENGTH
1/4”
11/32”
RPM
20,000
20,000
3/8”
7/32”
1/4”
20,000
1/4”
3/16”
13/32”
20,000
3/8"
9/32"
5/16"
20,000
3/8”
9/32”
3/8”
20,000
1/2”
1/2”
9/32”
11/32”
9/32”
17/32”
20,000
20,000
1/2”
9/32”
17/32”
20,000
9/16”
9/32”
19/32”
20,000
1/2”
9/32”
3/4”
20,000
5/8”
9/32”
11/16”
20,000
1/2”
3/8”
1”
20,000
5/8”
3/8”
15/16”
20,000
1/2”
1/4”
1-1/2”
20,000
1/2”
11/32”
1-1/2”
20,000
5/8”
11/16”
1-7/16”
20,000
Tanis Brush
1-1/4”
1-3/8”
1-3/8"
1-1/2”
1-1/2”
2”
2”
2”
2-1/2”
2-1/2”
3”
3”
4”
4”
4”
(800) 234-7002 | (262) 646-9000
Power Brushes
Stainless Steel
TANIS
BRUSH
FILAMENT
ARBOR
FACE
TRIM
MAX
PART NO.
10400
10405
10410
10415
10430
10440
10450
10455
10460
10465
10475
10480
10495
10500
10505
DIAMETER
1”
1-1/4”
DIAMETER
.006
.006
.006
.008
.006
.0104
.014
.006
.008
.0104
.014
.006
.006
.0104
.0118
HOLE
1/4”
1/4”
WIDTH
11/64”
3/16”
LENGTH
1/4”
11/32”
RPM
20,000
20,000
3/8”
9/32”
3/8”
20,000
1/2”
11/32”
17/32”
20,000
1/2”
9/32”
17/32”
20,000
1/2”
3/8”
1”
20,000
5/8”
3/8”
15/16”
20,000
5/8”
11/16”
1-7/16”
20,000
1-1/2”
2”
2”
3”
3”
4”
Encapsulated Carbon Steel
TANIS
BRUSH
FILAMENT
ARBOR
FACE
TRIM
MAX
PART NO.
10515
10520
10525
10530
10535
10540
DIAMETER
1-1/2”
DIAMETER
.0118
.0118
.014
.014
.0118
.014
HOLE
3/8”
WIDTH
9/32”
LENGTH
3/8”
RPM
20,000
1/2”
9/32”
17/32”
20,000
1/2”
9/32”
3/4”
20,000
1/2”
3/8”
1”
20,000
2”
2-1/2”
3”
Brass
TANIS
BRUSH
FILAMENT
ARBOR
FACE
TRIM
MAX
PART NO.
10545
10550
10555
10575
10585
DIAMETER
1-1/2”
2”
DIAMETER
.005
.005
.005
.014
.005
HOLE
3/8”
3/8”
WIDTH
9/32”
11/32”
LENGTH
3/8”
5/8”
RPM
20,000
20,000
1/2”
11/32”
17/32”
20,000
5/8”
11/16”
1-7/16”
20,000
2”
4”
www.tanisbrush.com
[email protected]
Made in USA
49
Power Brushes
COPPER CENTER NON-METALLIC WHEELS
Non-metallic wheels for soft or scratch susceptible surfaces. Nylon is often recommended for wet applications and polishing. Tampico is most commonly used
in wet and dry cleaning applications. Suggested applications are polishing, smoothing and finish treating. Maximum safe running speed is 20,000 RPM.
Black Horse Hair
TANIS
PART NO.
10595
10600
BRUSH
DIAMETER
2”
3”
FILAMENT
ARBOR
FACE
TRIM
MAX
MATERIAL
HOLE
1/2”
1/2”
WIDTH
3/8”
3/8”
LENGTH
17/32”
1”
RPM
20,000
20,000
FILAMENT
ARBOR
FACE
TRIM
MAX
MATERIAL
HOLE
1/2”
1/2”
WIDTH
3/8”
11/16”
LENGTH
17/32”
15/16”
RPM
20,000
20,000
Horse Hair
Tampico
TANIS
PART NO.
10655
10660
BRUSH
DIAMETER
2”
3”
Tampico
Crimped Black Nylon Type 6-12
Drill Press Shanks -
TANIS
BRUSH
FILAMENT
ARBOR
FACE
TRIM
MAX
PART NO.
10610
10615
10620
10625
10640
10645
10650
DIAMETER
1-1/2”
DIAMETER
.010
.008
.010
.016
.016
.010
.010
HOLE
3/8”
WIDTH
1/4”
LENGTH
3/8”
RPM
20,000
1/2”
3/8”
17/32”
20,000
1/2"
5/8”
5/8”
9/32"
3/8”
5/16”
11/16"
15/16”
1-7/16”
20,000
20,000
20,000
2”
3"
3”
4”
For use in portable tools and drill presses with 1/4” chuck adaptability.
10026
TANIS
SHANK
ARBOR
FOR ARBOR
OVERALL
PART NUMBER
10025
10026
10027
DIAMETER
1/4”
1/4”
1/4”
HOLE
1/4”
3/8”
1/2”
WIDTH UP TO
5/8”
7/8”
3/8”
LENGTH
2-1/2”
2-1/2”
2-1/2”
when using wire
brushes.
50
Tanis Brush
(800) 234-7002 | (262) 646-9000
Power Brushes
CERAMIX® COPPER CENTER WHEEL BRUSHES
CeramiX® small profile wheels for cleaning, polishing and deburring recessed areas such as small openings, slots, machined grooves, fine deburring
on medical instruments and gear splines. CeramiX® contains 3M™ Company 321 mineral grain which provides enhanced cutting action up to 3-5
times greater than traditional abrasive filaments. CeramiX® fractures in sharper, jagged surfaces for superior abrasion providing minimum cycle
times, increased productivity and maximizes abrasive media on part.
TANIS
PART NO.
35505
35510
35515
35520
35525
35530
35535
35540
35545
35550
BRUSH
DIAMETER
1-1/2”
2”
2-1/2”
3”
FILAMENT
DIAMETER
.028
.028
.035
.040
.028
.040
.028
.035
.040
.040
GRIT
120
120
180
80
120
80
120
180
120
80
ARBOR
HOLE
1/2”
FACE
WIDTH
3/16”
TRIM
LENGTH
1/4”
1/2”
1/4”
5/8”
5/16”
5/8”
10,000
1/2”
3/8”
7/8”
10,000
3/8”
MAX
RPM
10,000
10,000
SILICON CARBIDE COPPER CENTER WHEEL BRUSHES
Silicon Carbide small profile wheels are known for durability and preferred for finishing ferrous metals.
TANIS
PART NO.
35570
35575
35580
35585
35590
35595
35600
35605
35610
35615
35620
35625
BRUSH
DIAMETER
1-1/2”
2”
2-1/2”
3”
FILAMENT
DIAMETER
.035
.022
.018
.022
.040
.022
.035
.022
.022
.035
.022
.040
GRIT
180
120
500
120
120
320
180
120
320
180
120
120
ARBOR
HOLE
FACE
WIDTH
TRIM
LENGTH
MAX
RPM
1/2”
3/16”
1/4”
10,000
1/2”
1/4”
1/2”
10,000
5/8”
5/16”
5/8”
10,000
1/2”
3/8”
7/8”
10,000
Air Motor Shanks
For air motors and flexible shafts. Accepts single or multiple brushes.
10033
TANIS
SHANK
ARBOR
FOR ARBOR
OVERALL
PART NO.
10030
10031
10032
10033
DIAMETER
1/4”
1/4”
3/16”
1/4”
HOLE
1/2”
3/8”
1/4”
5/8”
WIDTH UP TO
3/8”
3/8”
3/4”
3/8”
LENGTH
1-7/8”
1-5/8”
1-3/4”
1-7/8”
10032
10031
Plastic Bushings
Plastic bushings are designed for economical, one-time use to match the brush inside diameter with your mounting shaft. Available in a range of inner and
outer diameters. For safety, use only one per brush. Flange eliminates side movement.
TANIS
OUTSIDE
INSIDE
PART NO.
10035
10036
10037
10038
DIAMETER
3/8”
1/2”
1/2”
5/8”
DIAMETER
1/4”
1/4”
3/8”
1/2”
www.tanisbrush.com
[email protected]
Made in USA
51
Power Brushes
RADIAL END BRUSHES
Constructed copper center crimped wire wheels permanently mounted on 1/4” shanks between oversized side plates. This design results in stiffer construction equal to bench mounted wheels and eliminates the need for reverse shanks. Suggested applications include cleaning and polishing surfaces.
Maximum safe running speed is 20,000 RPM.
Carbon Steel
TANIS
BRUSH
FILAMENT
FACE
TRIM
MAX
PART NO.
10840
10845
10850
10855
10860
10865
10870
10875
10880
10890
10900
10905
DIAMETER
DIAMETER
.006
.008
.0104
.0118
.006
.0118
.014
.0118
.014
.008
.0118
.014
WIDTH
LENGTH
RPM
1/4”
3/8”
20,000
11/32”
3/8”
3/8”
7/16”
7/16”
7/16”
20,000
20,000
20,000
11/32”
9/16”
20,000
1/2”
7/8”
20,000
1-1/2”
2”
2”
2”
2-1/2”
3”
Stainless Steel
TANIS
BRUSH
FILAMENT
FACE
TRIM
MAX
PART N0.
10910
10915
10920
10930
10935
10940
10945
10955
DIAMETER
DIAMETER
.006
.008
.0118
.006
.008
.0104
.0104
.014
WIDTH
LENGTH
RPM
3/16”
3/8”
20,000
1/4”
3/8”
20,000
3/8”
7/16”
20,000
1/2”
7/8”
20,000
FILAMENT
DIAMETER
.014
FACE
WIDTH
1/2”
TRIM
LENGTH
7/8”
MAX
RPM
20,000
1-1/2”
1-1/2”
2”
3”
Brass
TANIS
PART NO.
10975
BRUSH
DIAMETER
3”
SQUARE TRIM BRUSHES
Designed to clean both sides and bottom of a hole in one operation. Made with 1/4” shank for easy installation on portable or stationary tools. High concentration and uniform wire
fill. Ideal for cleaning internal areas and removing fine burrs from cross-drilled holes; also for cleaning corners and irregular shaped surfaces.
Carbon Steel
TANIS
PART NO.
11430
11435
11440
11455
52
Tanis Brush
BRUSH
DIAMETER
1”
1-1/16”
1-1/4”
1-7/8”
FILAMENT
DIAMETER
.006
.006
.006
.006
(800) 234-7002 | (262) 646-9000
TRIM LENGTH
(From Bottom)
3-5/8”
3-21/32”
3-3/4”
4-1/16”
MAX.
RPM
4,500
4,500
4,500
4,500
Power Brushes
CONFLARE BRUSHES
Shank mounted and ruggedly constructed for tough cleaning jobs on internal and external surfaces. Highly effective for side cleaning while eliminating
bottom scoring. The brush will not flare during operation. Less aggressive action and longer brush life compared to other circular styles due to wire angle.
Suggested applications include weld and carbon removal, deburring and plastic flash removal. Maximum safe running speed is 20,000 RPM.
Carbon Steel
TANIS
BRUSH
FILAMENT
TRIM LENGTH
MAX
PART NO.
10728
10730
10735
10740
10745
10750
10760
10765
10775
10780
DIAMETER
DIAMETER
.006
.0118
.006
.008
.014
.006
.014
.006
.014
.014
(From Bottom)
RPM
3/8”
20,000
1/2”
20,000
5/8”
20,000
15/16”
20,000
1-1/4”
20,000
TRIM LENGTH
(From Bottom)
3/8”
1/2”
MAX
RPM
20,000
20,000
15/16”
20,000
1-1/2”
2”
2-1/2”
3”
4”
Stainless Steel
TANIS
PART NO.
10795
10805
10820
10830
BRUSH
DIAMETER
1-1/2”
2”
3”
FILAMENT
DIAMETER
.006
.014
.006
.014
CIRCULAR FLARED END BRUSHES
Densely filled brush for longer life and made with 1/4” shank. Suggested applications include removing rust and paint, spot facing, polishing tool and die molds,
weld cleaning, mold cleaning and deburring. Maximum safe running speed is 20,000 RPM to 2” in diameter, larger diameters max safe speed is 15,000 RPM.
Carbon Steel
TANIS
PART NO.
11100
11105
11110
11115
11120
11130
11135
11145
11160
11170
11180
11185
11190
11200
11205
11210
Stainless Steel
BRUSH
DIAMETER
1”
1-1/4”
1-1/2”
2”
2-3/4”
3”
4”
FILAMENT
DIAMETER
.006
.008
.020
.006
.008
.006
.008
.020
.014
.008
.020
.006
.008
.014
.020
.008
MAX
TANIS
BRUSH
FILAMENT
MAX
RPM
PART NO.
11215
11220
11230
11235
11240
11255
11260
11265
11270
11275
DIAMETER
DIAMETER
.006
.008
.006
.008
.020
.008
.006
.008
.020
.008
RPM
20,000
20,000
20,000
15,000
15,000
1”
1-1/2”
2-3/4”
3”
4”
20,000
20,000
15,000
15,000
15,000
15,000
15,000
www.tanisbrush.com
[email protected]
Made in USA
53
Power Brushes
WIRE END BRUSHES
End brushes are made with 1/4” shank. Effective for cleaning and accurate brushing action in tight areas. Suggested applications include removing slag,
scale, rust and paint; tool and die finishing and cleaning surface areas.
Carbon Steel
Stainless Steel
54
TANIS
BRUSH
FILAMENT
TRIM
OVERALL
STEM
MAX
PART NO.
11280
11285
11290
11295
11300
11305
11310
11315
11320
11325
11330
11335
DIAMETER
DIAMETER
.006
.0104
.014
.020
.006
.0104
.014
.020
.006
.0104
.014
.020
LENGTH
LENGTH
DIAMETER
RPM
1”
2-3/4”
1/4”
20,000
1”
2-3/4”
1/4”
20,000
1”
2-3/4”
1/4”
20,000
1/2”
3/4”
1”
TANIS
BRUSH
FILAMENT
TRIM
OVERALL
STEM
MAX
PART NO.
11340
11345
11350
11355
11360
11365
11370
11375
11380
11385
DIAMETER
DIAMETER
.006
.0104
.014
.006
.0104
.014
.020
.006
.0104
.014
LENGTH
LENGTH
DIAMETER
RPM
1”
2-3/4”
1/4”
20,000
1”
2-3/4”
1/4”
20,000
1”
2-3/4”
1/4”
20,000
Tanis Brush
1/2”
3/4”
1”
(800) 234-7002 | (262) 646-9000
Power Brushes
CERAMIX® END BRUSHES
CeramiX® end brushes feature an integrated stem that allows mounting in a collet or tool holder for CNC machine or robotic use. End brushes can also be used
in portable air or electric tools. End brushes are a great choice for deburring slots, small recessed areas and internal part features. CeramiX® end brushes are
able to deliver a targeted brushing action to small areas on machined parts to blend end-mill tool marks, deburr and blend rough edges and provide ideal
TANIS
PART NO.
35700
35705
35710
35715
35720
35725
35730
35735
35740
BRUSH
DIAMETER
1/2”
3/4”
1”
GRIT
120
180
220
120
180
220
120
180
220
FILAMENT
DIAMETER
.040
.035
.022
.040
.035
.022
.040
.035
.022
TRIM
LENGTH
OVERALL
LENGTH
STEM
DIAMETER
MAX
RPM
1”
2-3/4”
1/4”
10,000
1”
2-3/4”
1/4”
10,000
1”
2-3/4”
1/4”
10,000
SILICON CARBIDE END BRUSHES
Silicon Carbide end brushes feature an integrated stem that allows mounting in a collet or tool holder for CNC machine or robotic use. End brushes can also be
used in portable air or electric tools. End brushes are a great choice for deburring slots, small recessed areas and internal part features.
TANIS
PART NO.
35745
35750
35755
35760
35765
35770
35775
35780
35785
BRUSH
DIAMETER
1/2”
3/4”
1”
GRIT
120
180
320
120
180
320
120
180
320
FILAMENT
DIAMETER
.040
.035
.022
.040
.035
.022
.040
.035
.022
TRIM
LENGTH
OVERALL
LENGTH
STEM
DIAMETER
MAX
RPM
1”
2-3/4”
1/4”
10,000
1”
2-3/4”
1/4”
10,000
1”
2-3/4”
1/4”
10,000
when using wire
brushes.
www.tanisbrush.com
[email protected]
Made in USA
55
Power Brushes
MINIATURE WHEEL BRUSHES
Permanently mounted on steel stem for use with portable and flexible tools. Constructed with perfect balance for longer brush life and no vibration
during use. Suggested applications include light cleaning and deburring and blending of surface junctures.
Carbon Steel
TANIS
BRUSH
DIAMETER
PART NO.
11460
11465
11470
11475
11480
11485
11490
11495
11500
3/4”
3/4”
1”
1”
1-1/4”
1-1/2”
FILAMENT
TRIM
STEM
MAX
DIAMETER
.003
.005
.003
.005
.003
.005
.005
.005
.005
LENGTH
SIZE
RPM
3/16”
1/8”
25,000
3/16”
3/32”
25,000
5/16”
1/8”
25,000
5/16”
3/8”
1/2”
3/32”
1/8”
1/8”
25,000
25,000
25,000
FILAMENT
TRIM
STEM
MAX
DIAMETER
.005
.003
LENGTH
SIZE
RPM
3/16”
1/8”
25,000
Stainless Steel
TANIS
BRUSH
DIAMETER
PART NO.
11505
11510
3/4”
1”
Brass
TANIS
PART NO.
11515
11520
11525
FILAMENT
TRIM
STEM
MAX
LENGTH
SIZE
RPM
3/16”
3/32”
25,000
1”
DIAMETER
.003
.005
.005
5/16”
1/8”
25,000
BRUSH
DIAMETER
FILAMENT
MATERIAL
TRIM
STEM
MAX
LENGTH
SIZE
RPM
3/4”
Stiff Hair
Soft Hair
Stiff Hair*
Stiff Hair
3/32”
25,000
1/8”
25,000
BRUSH
DIAMETER
3/4”
Bristle
TANIS
PART NO.
11530
11535
11540
11545
3/16”
* Double thick
when using wire
brushes.
56
Tanis Brush
(800) 234-7002 | (262) 646-9000
Power Brushes
MINIATURE CUP BRUSHES
Permanently mounted on steel stem for use with portable and flexible tools. Constructed with perfect balance, fill material is evenly distributed around brush
face for uniform wear and longer brush life. Suggested applications include light deburring, blending surfaces and light cleaning in small electronic instruments.
TANIS
PART NO.
11550
11555
11560
11565
11570
11575
11580
11585
11590
11595
BRUSH
DIAMETER
5/8”
5/8”
5/8”
1/2”
9/16”
1”
FILAMENT
TRIM
STEM
MAX
MATERIAL
.003 Carbon Steel
LENGTH
SIZE
RPM
1/4”
1/8”
25,000
1/4”
1/8”
25,000
1/4”
1/8”
25,000
5/32”
3/32”
25,000
1/4”
1/8”
25,000
7/16”
1/8”
25,000
.005 Carbon Steel
.005 Stainless Steel
.003 Brass
.005 Brass
Stiff Hair
Stiff Hair
Soft Hair
Stiff Hair
Soft Hair
MINIATURE END BRUSHES
Constructed with perfect balance for longer brush life and uniform wear around the brush face. Ferrule and steel stem are a one-piece construction to
ensure no separation during operation. Suggested applications include blending surface areas light cleaning in small electronic instruments and light
deburring.
TANIS
PART NO.
11600
11605
BRUSH
DIAMETER
FILAMENT
TRIM
STEM
MAX
MATERIAL
LENGTH
RPM
3/16”
.003 Carbon Steel
1/4”
SIZE
1/8”
11610
1/4”
.005 Carbon Steel
7/16”
11615
5/16”
.005 Carbon Steel
9/16”
11620
3/16”
1/4”
11625
1/4”
7/16”
11630
5/16”
9/16”
11635
3/16”
.003 Brass
1/4”
11640
1/4”
.005 Brass
7/16”
3/16”
Stiff Hair
11645
11650
Stiff Hair
11655
11660
11665
11670
5/16”
Stiff Hair
Stiff Hair
Stiff Hair
25,000
1/8”
25,000
1/8”
25,000
1/8”
25,000
3/32”
1/4”
Soft Hair
1/4”
3/32”
1/8”
25,000
1/8”
3/8”
9/16”
3/32”
1/8”
1/8”
www.tanisbrush.com
25,000
25,000
[email protected]
57
Scratch Brushes
APPLICATOR BRUSHES
Solid bent hardwood or delrin block. Wire material is hand drawn into block. Excellent for spot cleaning.
Solid bent hardwood block. Wire material is hand drawn into a wood block.
Excellent for spot cleaning.
TANIS
PART NO.
08000
FILAMENT DIAMETER
BLOCK SIZE
8-3/8” X 1”
NO. OF
TRIM
BRUSH
ROWS
4X7
LENGTH
3/4”
LENGTH
1-5/8”
Solid bent delrin handle. Wire material is hand drawn into a delrin block.
Excellent for cleaning hard to reach areas in highly corrosive situations.
TANIS
PART NO.
08001
08002
08003
FILAMENT DIAMETER
BLOCK SIZE
6-1/2” X 3/8”
NO. OF
TRIM
BRUSH
ROWS
1 X 11
2 X 11
3 X 11
LENGTH
LENGTH
7/16”
1-1/4”
Solid bent hardwood block. Wire material is hand drawn into a wood block.
Excellent for cleaning hard to reach areas.
TANIS
PART NO.
08014
08015
08016
FILAMENT DIAMETER
BLOCK SIZE
7-3/4” X 7/16”
NO. OF
TRIM
BRUSH
ROWS
1 X 11
2 X 11
3 X 11
LENGTH
LENGTH
7/16”
1-1/4”
Solid bent delrin handle. Nylon fill material is hand drawn into a delrin handle.
Excellent for cleaning hard to reach areas and surfaces that cannot be scratched.
TANIS
PART NO.
08009
08010
08011
FILAMENT DIAMETER
BLOCK SIZE
.012 Natural Nylon
.012 Natural Nylon
.012 Natural Nylon
6-1/2” X 3/8”
NO. OF
TRIM
BRUSH
ROWS
1 X 11
2 X 11
3 X 11
LENGTH
LENGTH
7/16”
1-1/4”
SMALL HAND SCRATCH BRUSHES
Excellent hand cleaning tools for hard to reach areas and general industrial purposes.
Stove and Appliance Brushes
Curved smooth hardwood handle. Used as a scouring brush for small areas.
TANIS
PART NO.
00461
00462
00463
58
Tanis Brush
FILAMENT
MATERIAL
BLOCK SIZE
.008 Brass
.008 Aluminum
8-5/8” X 1/2”
(800) 234-7002 | (262) 646-9000
NO. OF
TRIM
BRUSH
ROWS
LENGTH
5/8”
5/8”
1/2”
LENGTH
2X9
2-7/8”
Scratch Brushes
SMALL HAND SCRATCH BRUSHES
Excellent hand cleaning tools for hard to reach areas and general industrial purposes.
Wood Handle Welders Brushes
Solid bent hardwood block. Excellent for cleaning small welds and hard to reach areas.
TANIS
PART NO.
00025
00026
00027
00028
00029
FILAMENT
MATERIAL
BLOCK SIZE
.006 Brass
.006 Bronze
.016 Nylon
Horse Hair
7-3/4” X 7/16”
NO. OF
TRIM
BRUSH
ROWS
LENGTH
LENGTH
3X7
1/2”
1-1/2”
Plastic Handle Welders Brushes
Plastic block. Used for cleaning small welds and hard to reach places.
TANIS
PART NO.
00030
00031
00032
00033
00034
FILAMENT
MATERIAL
BLOCK SIZE
.006 Brass
.006 Bronze
.016 Nylon
Horse Hair
7-1/4” X 7/16”
NO. OF
TRIM
BRUSH
ROWS
LENGTH
LENGTH
3X7
1/2”
1-1/2”
Double Sided Plastic Handle Welders Brushes
Plastic block. Two filament materials in one brush to clean multiple surface areas.
TANIS
PART NO.
10040
10045
FILAMENT
MATERIAL
BLOCK SIZE
St St / Nylon
St St / Brass
7-1/4” x 7/16”
NO. OF
TRIM
BRUSH
ROWS
LENGTH
LENGTH
3X7
1/2”
1-1/2”
Wood Handle Horsehair Utility Brushes
TANIS
PART NO.
00023
FILAMENT
MATERIAL
BLOCK SIZE
Horse Hair
7” x 1/2”
NO. OF
TRIM
BRUSH
ROWS
4 X 15
LENGTH
1/2”
LENGTH
1-3/4”
Wood Handle Utility Brushes
Shaped hardwood handle.
TANIS
PART NO.
00044
00045
00046
00047
00048
FILAMENT
MATERIAL
NO. OF
TRIM
BRUSH
ROWS
LENGTH
LENGTH
6” X 1/2”
3 X 10
9/16”
1-1/2”
6” X 1/2”
6” X 1/2”
3 X 10
3 X 10
1/2”
5/8”
1-1/2”
1-1/2”
BLOCK SIZE
.014 Nylon
Horse Hair
.006 Brass
.006 Steel
Wood Handle Upright Brushes
Smooth hardwood block. For cleaning confined hard to reach areas.
TANIS
PART NO.
00035
00036
00037
00038
00039
FILAMENT
BLOCK SIZE
.014 Nylon
Horse Hair
.006 Brass
.006 Steel
4-3/4” X 1”
www.tanisbrush.com
NO. OF
TRIM
BRUSH
ROWS
LENGTH
LENGTH
2X6
1/2”
7/8”
[email protected]
Made in USA
59
Scratch Brushes
General Purpose-Hand Brushes are made with a variety of block shapes and fill materials. Durable brushes for
cleaning small surface areas and general industrial purposes.
Small Utility Brushes
Curved smooth hardwood block or plastic handle. Light duty scrub brush.
TANIS
PART NO.
00500
00501
00502
00504*
00505*
00506*
FILAMENT
MATERIAL
.008 Brass
.008 Aluminum
.016 Natural Nylon
.008 Brass
.016 Natural Nylon
BLOCK SIZE
NO. OF
TRIM
BRUSH
ROWS
LENGTH
5/8”
1/2”
5/8”
5/8”
5/8”
5/8”
LENGTH
6-3/4” X 1-5/8”
6X9
7-1/4” X 1-5/8”
6X9
2-1/2”
2-1/2”
* Plastic Handle
Utility 2-Way Cleaning Brush
TANIS
FILAMENT
MATERIAL
BLOCK SIZE
.025 Crimped Natural Polyester
.010 Crimped Brass on tip
Tapered
PART NO.
00525
NO. OF
TRIM
BRUSH
ROWS
5X7
3X6
LENGTH
LENGTH
2-1/4”
1/2”
5/8”
Large Utility Brushes
Curved smooth hardwood block or plastic handle. Light to heavy duty cleaning.
TANIS
PART NO.
00510
00510-N
00511*
00512*
00513*
FILAMENT
MATERIAL
BLOCK SIZE
.008 Brass
.016 Black Nylon
.008 Brass
.016 Natural Nylon
8-7/8” X 2-5/8”
NO. OF
TRIM
BRUSH
ROWS
LENGTH
LENGTH
9 X 10
5/8”
3”
* Plastic Handle
Suede and Nail Brushes
Smooth hardwood block with hand groove. Used for general cleaning.
TANIS
PART NO.
00520
00521
60
Tanis Brush
FILAMENT
MATERIAL
BLOCK SIZE
.005 Brass
White Tampico
3-1/4” X 1-1/8”
5” X 1-1/2”
(800) 234-7002 | (262) 646-9000
NO. OF
TRIM
BRUSH
ROWS
4 X 11
4 X 15
LENGTH
9/16”
3/4”
LENGTH
3”
4-3/8”
Scratch Brushes
Steel Wire Hand Scratch Brushes are densely filled with an even trim to provide a uniform brushing face. They are made with
solid hardwood blocks, smoothly finished and shaped for more comfortable brushing. Wood handles are made in two shapes.
Excellent industrial tools for general cleaning purposes.
Shoe Handle Scratch Brushes
Wood shoe handle.
TANIS
PART NO.
00449
00449-SS
00450
00450-SS
00452
00452-SS
00452-BZ
00452-SC*
FILAMENT
MATERIAL
.013 Black Temp.Wire
.014 Phos. Bronze
BLOCK SIZE
NO. OF
ROWS
10” X 3/8”
1 X 17
10” X 5/8”
2 X 17
10” X 1-1/8”
TRIM
LENGTH
BRUSH
LENGTH
1-3/16”
5”
4 X 17
* Scraper Attached
Curved Handle Scratch Brushes
Curved wood handle.
TANIS
PART NO.
FILAMENT
MATERIAL
00456
00458
00458-SS
00458-SC*
00459
00459-SS
00459-SC*
* Scraper Attached
BLOCK SIZE
NO. OF
TRIM
BRUSH
ROWS
LENGTH
LENGTH
1-3/16”
6-1/4”
13-3/4” X 3/8”
1 X 18
13-3/4” X 1”
3 X 19
13-3/4” X 1-1/8”
4 X 18
** Foam Block Handle
when using wire
brushes.
www.tanisbrush.com
[email protected]
Made in USA
61
Scratch Brushes
Platers’ Hand Brushes are designed for general industrial cleaning in the metal finishing and plating industries. Solid hardwood blocks
are used for more comfortable brushing. Blocks are made with two different shapes.
Shoe Handle Platers’ Brushes
Hardwood block. Used for light cleaning and polishing for metal finishing, plating and general industrial
applications.
TANIS
PART NO.
FILAMENT
MATERIAL
BLOCK SIZE
00420
00421
00422
00423
00423-SS
00428
.006 Brass
.006 Brass
.006 Steel
.006 Steel
White Tampico
10” X 7/8”
10” X 1-1/8”
10” X 7/8”
10” X 1-1/8”
10” X 1-1/8”
10” X 1-1/8”
NO. OF
TRIM
BRUSH
ROWS
LENGTH
LENGTH
3 X 18
4 X 18
3 X 18
4 X 18
4 X 18
4 X 18
1”
5”
Curved Handle Platers’ Brushes
Curved wood handle. Used for light cleaning and polishing for metal finishing, plating and general
industrial applications.
TANIS
PART NO.
FILAMENT
MATERIAL
BLOCK SIZE
00400
00401
00402
00402-SS
00403
00403-SS
00407
00408
00409
00410
.006 Brass
.006 Brass
.006 Steel
.006 Steel
Black Nylon
White Tampico
White Tampico
White Tampico
13” X 7/8”
13” X 1-1/8”
13” X 7/8”
13” X 7/8”
13” X 1-1/8”
13” X 1-1/8”
13” X 1-1/8”
13” X 3/4”
13” X 1-1/4”
13” X 1-3/4”
NO. OF
TRIM
BRUSH
ROWS
LENGTH
LENGTH
3 X 19
4 X 19
3 X 19
3 X 19
4 X 19
4 X 19
4 X 19
2 X 19
4 X 19
6 X 19
1”
5-1/2”
Scouring and Scrub Brushes
Smooth hardwood block with beveled sides.
TANIS
62
PART NO.
FILAMENT
MATERIAL
BLOCK SIZE
10050
10055
White Tampico
White Tampico
2-5/8” X 6-1/2”
3” X 8-1/4”
Tanis Brush
(800) 234-7002 | (262) 646-9000
NO. OF
TRIM
BRUSH
ROWS
LENGTH
LENGTH
6 X 14
7 X 18
1-1/8”
1-1/8”
6-3/8”
7-5/8”
Scratch Brushes
Tanis Brushes for the Flexographic Industry are made with the highest quality materials to assure consistent brushing action and longer
brush life. Anilox rollers should be cleaned on a regular basis for best results. When cleaning a stainless steel roller use a brass brush and
use a stainless steel brush to clean ceramic rollers. Nylon, horse hair and pure bristle provide different grades of stiffness for light cleaning.
Anilox or Halftone Brushes
Solid hardwood block with sealer tumbled finish or water resistant laminated hardwood block with
clear lacquer finish.
TANIS
PART NO.
FILAMENT
MATERIAL
BLOCK SIZE
04000
04001
04002
04003
04005
04028*
04088
04089
04090
.003 Brass
Horse Hair
Pure Bristle
.003 Brass Center with Horse Hair Border
.003 Brass Center with Horse Hair Border
.005 Brass
.012 Black Nylon Type 6-12
2-1/2” X 4-1/4”
TRIM
LENGTH
3/4”
*Laminated Wood Block
Large Anilox or Halftone Brushes
Densely filled brushes with hand grooves in sides of block. Water resistant laminated hardwood block with
lacquer finish.
TANIS
PART NO.
04006
FILAMENT
MATERIAL
BLOCK SIZE
.005 Brass
2-5/8” X 6-1/2”
TRIM
LENGTH
3/4”
Anilox Finishing Brushes
Water resistant laminated hardwood block with clear lacquer finish.
TANIS
PART NO.
FILAMENT
MATERIAL
BLOCK SIZE
04007
04008
04009
.012 Black Nylon Type 6-12
Pure Bristle
Horse Hair
2-3/8” X 6”
TRIM
LENGTH
1”
when using wire
brushes.
www.tanisbrush.com
[email protected]
Made in USA
63
Artist Brushes
Red Sable Marking Brushes
Red sable marking brushes with seamless aluminum ferrule and walnut color lacquered handle. Quality material that
has a soft texture and shape enabling brush to hold fluid colors. Excellent for detail work due to needle sharp point.
TANIS
SIZE
PART NO.
00328
00329
00330
00331
00332
00333
00334
00335
00336
#000
#00
#0
#1
#2
#3
#4
#5
#6
BRUSH
TRIM
OVERALL
DIAMETER
1/16”
1/16”
5/64”
5/64”
3/32”
7/64”
1/8”
9/64”
5/32”
LENGTH
7/32”
15/64”
9/32”
5/16”
3/8”
7/16”
1/2”
9/16”
21/32”
LENGTH
7-1/2”
Taklon White Artist Brushes
White taklon brushes with seamless aluminum ferrule and unfinished wood handle. Taklon is a tapered nylon material
to provide an even flow. Ideal for acrylics.
TANIS
SIZE
PART NO.
00290
00291
00292
00294
00296
00298
00299
#0
#1
#2
#4
#6
#8
#10
BRUSH
TRIM
OVERALL
DIAMETER
5/64”
3/32”
3/32”
1/8”
3/16”
7/32”
1/4”
LENGTH
5/16”
3/8”
7/16”
9/16”
11/16”
7/8”
15/16”
LENGTH
7-1/2”
Round White Bristle Marking Brushes
Round white bristle marking brushes with aluminum ferrule and white wood handle. Natural split ends of material holds
onto heavy paint. Best choice for oil and acrylic. Excellent for industrial general marking purposes or touch-up work.
TANIS
SIZE
PART NO.
00365
00366
00367
00368
00369
00370
#1
#2
#3
#4
#5
#6
BRUSH
TRIM
OVERALL
DIAMETER
7/64”
5/32”
3/16”
7/32”
1/4”
9/32”
LENGTH
5/8”
3/4”
7/8”
1”
1-1/8”
1-1/4”
LENGTH
7”
White Bristle Marking Brushes
White bristle marking brushes with seamless aluminum ferrule and unfinished wood handle. Holds onto heavy paint due
to the split ends of each bristle. Best choice for oil and acrylic.
TANIS
PART NO.
00280
00281
00282
00283
00284
00285
00286
SIZE
#0
#1
#2
#3
#4
#5
#6
BRUSH
DIAMETER
3/32”
1/8”
5/32”
3/16”
7/32”
9/32”
5/16”
TRIM
LENGTH
1/2”
11/16”
3/4”
7/8”
1”
1-1/16”
1-1/8”
Black Bristle Fitch Brushes
OVERALL
LENGTH
11-5/16”
11-9/16”
11-3/4”
12-3/32”
12-5/16”
12-1/2”
12-11/16”
Fitch brush with black bristle and tapered trim for detail work. Made with aluminum ferrule and unfinished
wood handle. Black bristle used best with oil and acrylic.
TANIS
PART NO.
00270
00271
00272
00273
00274
64
Tanis Brush
WIDTH
1/4”
3/8”
1/2”
3/4”
1”
TRIM
LENGTH
13/16”
7/8”
1”
1-5/16”
1-1/2”
(800) 234-7002 | (262) 646-9000
OVERALL
LENGTH
12”
12”
12”
13”
13”
Artist Brushes
Gold Nylon Flat Artist Brushes
Gold nylon brushes have seamless aluminum ferrule and enameled wood handle. Nylon is a long wearing synthetic filament that provides an even flow. Ideal for acrylics.
TANIS
PART NO.
00221
00222
00223
00224
00225
SIZE
WIDTH
5/32”
3/16”
1/4”
5/16”
3/8”
#2
#4
#6
#8
#10
TRIM
OVERALL
LENGTH
7/32”
1/4”
5/16”
3/8”
7/16”
LENGTH
7”
7-1/8”
7-1/4”
7-1/2”
7-5/8”
Camel Hair Flat Lacquering Brushes
Camel hair flat lacquering brushes have seamless aluminum ferrule and black wood handle. Material is very absorbent
and works well with liquid paints, inks and dyes. Excellent for touch-up work.
TANIS
PART NO.
00390
00391
00392
00393
SIZE
1/8”
1/4”
3/8”
1/2”
TRIM
OVERALL
LENGTH
1/2”
9/16”
11/16”
3/4”
LENGTH
7”
Black Sable Ox Hair Stroke Brushes
Black sable ox hair stroke brushes with seamless aluminum ferrule and orange polished handle. Quality material that
has a soft texture and holds fluid colors for a sharp stroke.
TANIS
SIZE
PART NO.
00322
00323
00324
00325
00326
1/8”
1/4”
3/8”
1/2”
3/4”
TRIM
OVERALL
LENGTH
5/8”
13/16”
15/16”
1-1/8”
1-5/16”
LENGTH
7-1/2”
White Bristle Fan Marking Brushes
Fan tip white bristle marking brush made with seamless nickel plated brass ferrule and unfinished
wood handle. Natural split ends of material holds onto heavy paint. Best used with oil and acrylic.
TANIS
PART NO.
00201
00202
00203
00204
00206
SIZE
WIDTH
#1
#2
#3
#4
#6
7/8”
1”
1-18”
1-3/8”
1-7/8”
TRIM
LEGNTH
1/2”
9/16”
5/8”
3/4”
7/8”
OVERALL
LENGTH
7-3/8”
7-1/2”
7-5/8”
7-5/8”
8”
Fine White Bristle Stencil Brushes
Stiff white bristle in a seamless ferrule and unfinished wood handle.
TANIS
PART NO.
00210
00211
00212
00213
00214
SIZE
#1
#2
#4
#6
#8
DIAMETER
3/16”
7/32”
9/32”
3/8”
7/16”
TRIM
OVERALL
LENGTH
1/2”
9/16”
11/6”
7/8”
15/16”
LENGTH
5-1/2”
5-5/8”
6”
6-1/4”
6-1/2”
Pony Hair Detail Brushes
Pony hair secured in a plastic ferrule and handle. Sometimes referred to as a lip brush.
TANIS
PART NO.
00021
DIAMETER
1/8”
TRIM
OVERALL
LENGTH
3/8”
LENGTH
3-3/8”
www.tanisbrush.com
[email protected]
65
Paint and Parts Cleaning Brushes
Paint and Parts Cleaning Brushes are used for several painting and cleaning applications where a disposable brush is necessary at
an economical cost. Brushes in this section are used for general industrial painting and cleaning applications and purposes.
White Bristle Chip Brushes
Disposable paint brush with White Bristle fill and wood handle for general cleaning and painting.
TANIS
PART NO.
00230
00231
00232
00233
00236
00234
00235
SIZE
1/2”
1”
1-1/2”
2”
2-1/2”
3”
4”
TRIM
OVERALL
WIDTH
1/4”
LENGTH
1-1/2”
LENGTH
7”
5/16”
1-5/8”
7-1/2”
5/16”
1-5/8”
8-1/2”
3/8”
1-5/8”
8-1/2”
Polyester Chip Brushes
Disposable paint brush with Polyester fill and plastic handle used for general cleaning and painting.
TANIS
PART NO.
00250
00251
00252
00253
00254
SIZE
1/2”
1”
1-1/2”
2”
3”
TRIM
OVERALL
WIDTH
1/4”
LENGTH
1-1/2”
LENGTH
7-1/4”
5/16”
1-5/8”
7-1/4”
5/16”
3/8”
1-5/8”
1-5/8”
7-1/2”
8-1/4”
Round Wire Chip Brushes
Round ferrule with Stainless Steel fill, long trim and twisted wire loop handle. Excellent for removing metal chips
especially in high temperature applications.
TANIS
PART NO.
08091
08092
BRUSH
DIAMETER
FILAMENT
DIAMETER
TRIM
LENGTH
OVERALL
LENGTH
7/8”
.005
1-1/2”
9”
18”
Pure bristle with nickel ferrule for quality industrial jobs.
TANIS
PART NO.
00100
00101
00102
00103
SIZE
1”
1-1/2”
2”
2-1/2”
WIDTH
7/16”
1/2”
9/16”
5/8”
TRIM
OVERALL
LENGTH
2-1/4”
2-1/2”
2-3/4”
2-3/4”
LENGTH
10-1/2”
11”
11”
11-3/4”
Pure bristle with long flat plastic handle for general industrial jobs.
TANIS
PART NO.
00111
00112
00113
66
Tanis Brush
SIZE
1”
1-1/2”
2”
WIDTH
3/8”
7/16”
1/2”
(800) 234-7002 | (262) 646-9000
TRIM
OVERALL
LENGTH
2”
2-1/4”
2-1/4”
LENGTH
10-3/4”
10-3/4”
11”
Paint and Parts Cleaning Brushes
Oval Sash Paint Brushes
Pure bristle with steel ferrule and lacquer plastic handle.
TANIS
PART NO.
00302
00304*
00306
00308
00310
00312
SIZE
#2
#4
#6
#8
#10
#12
WIDTH
7/16”
9/16”
13/16”
15/16”
1-1/16”
1-3/16”
TRIM
OVERALL
LENGTH
1-7/8”
2”
2-1/4”
2-1/4”
2-1/2”
2-3/4”
LENGTH
8-1/2”
9-1/2”
10”
10-3/4”
11”
11-1/2”
*Wood Handle
Tampico material. Durable natural fiber. Excellent utility brush for cleaning hard to reach areas.
TANIS
PART NO.
00303
00305
SIZE
#8
#10
WIDTH
1”
1-1/8”
TRIM
OVERALL
LENGTH
2-7/8”
2-7/8”
LENGTH
11-1/4”
11-1/2”
Polypropylene material. Rugged synthetic fill. Excellent utility brush for cleaning hard to reach areas especially
where chemicals or acids are used.
TANIS
PART NO.
00307
00309
SIZE
#8
#10
WIDTH
1”
1-1/8”
TRIM
OVERALL
LENGTH
2-7/8”
2-7/8”
LENGTH
11-1/4”
11-1/2”
Round Bridled Glue Brushes
Grey bristle with a wood handle. Brush part is bridled by a wire to stiffen the brush. Wire can be cut off for
longer brush life.
TANIS
PART NO.
00350
00351
00352
00353
00354
SIZE
#2
#4
#6
#8
#10
TRIM
OVERALL
WIDTH
1/4”
3/8”
1/2”
5/8”
3/4”
LENGTH
1-1/4”
1-3/8”
1-5/8”
1-3/4”
1-7/8”
LENGTH
TRIM
OVERALL
WIDTH
3/8”
1/2”
9/16”
LENGTH
LENGTH
3/4”
6”
7-1/4”
8”
Tin Handle Acid Brushes
Horse Hair fill with tin plated handle.
TANIS
PART NO.
02001
02002
02003
SIZE
#1
#2
#3
Wood Handle Dope Brush
Horse Hair fill with metal ferrule and wood handle.
TANIS
PART NO.
02007
DIAMETER
1-3/16”
TRIM
OVERALL
LENGTH
1-1/8”
LENGTH
7”
www.tanisbrush.com
[email protected]
67
Tanis Brush Website and RFQ Forms
Be sure to check out www.tanisbrush.com. Our new website contains
a wealth of information about Tanis’ complete offering of standard
items and made-to-order brush solutions. Handy links to the Request
For Quote forms give you quick access to our Brush Experts and allow
you to submit your RFQ online.
Tanis brings more than 25 years’ experience to every brush application, and our in-house design and engineering capabilities allow us to
be an industry leader in custom brush solutions. An ISO 9001:2008
certified manufacturer, Tanis employs advanced manufacturing
methods and quality control.
Custom Brush Capabilities:
Engineered and made-to-order brushes can be a completely customized solution or a variation of a standard brush product offered by Tanis Inc.
Tanis tailor-made brush products are geared with one goal in mind: providing our customers the best solution for their application. We have full
engineering and manufacturing capabilities for made-to-order custom brushes in abrasives, metal back strip, twisted, and stapled set brush constructions.
TA N I S
Safety Considerations
INCORPORATED
BRUSH USAGE RECOMMENDATIONS
Safety Information: Many Brush Manufacturers mark some safety warnings, recommendations, and usage restrictions directly to the product. it
is not always practical to include even the most limited safety information
on the brush itself. Therefore, the operator must read and follow all
instructions supplied in or on the product container as well as those
marked on the product itself. The operator should also refer to the safety
and operating information printed in the brush or power tool manufacturer's catalog, instruction manual, and other literature.
Self -Sharpening: When using wire wheel brushes, periodically reverse
the direction of rotation to take advantage of the self-sharpening action that
will result. this may be accomplished by removing the brush from the spindle and turning it side-for-side and remounting securely. (See Figure 2)
Pressure: Avoid excessive pressure when using a power brush.
Excessive pressure causes over-bending of the filaments and heat buildup resulting in filament breakage, rapid dulling and reduced brush life.
Instead of greater pressure on a brush, it is suggested that you try:
(1) A brush with a more aggressive cutting action (increased wire size,
decreased filament length, change to a different brush type, i.e. knot type
instead of crimped wire type), or (2) Higher speed (increased R.P.M.,
increased brush diameter).
SUMMARY
Power Brush Safety Requirements
Correct
(tips doing the work)
Incorrect
(excessive presure can
cause wire breakage)
Important Note: Never exceed the recommended MAXIMUM SAFE
FREE SPEED R.P.M. (MSFS) rating of the brush. See Figure 1.
Warning: In normal power brushing operations, the material being removed,
such as burrs, scale, dirt, weld slag or other residue, will fly off the brush with
considerable force along with brush filaments which break off due to fatigue.
Safety Goggles: Safety Goggles or Full Face Shields worn over Safety
Glasses with side shields, MUST BE WORN by all operators AND OTHERS IN
THE AREA of power brush operations. Comply with the requirements of ANSI
B165.1 "Safety Requirements - Power Brushes". Also see ANSI B7.1
"Safety Requirements - For the Use, Care and Protection of Abrasive
Wheels".
Safety Gloves and Protective Clothing: Appropriate protective clothing
must be used where there is a possibility of injury that can be prevented
by such clothing. The use of safety gloves is recommended.
Guards: Keep all machine guards in place.
The POTENTIAL OF SERIOUS INJURY EXISTS for both the brush operator and others in the work area (possible 50 feet or more feet from the
brush). To protect against this hazard before rotating the brush, during rotation, and until rotation stops, operators and others in the area must wear
safety goggles or full face shields worn over safety glasses with side
shields, and use protective clothing and equipment.
Speeds: Observe all speed restrictions indicated on the brushes, containers, labels or printed in pertinent literature. "MSFS" or "MAX.SFS"
means Maximum Safe Free Speed (R.P.M.)-spinning free with no work
applied: For reasons of Safety, the "MSFS/MAX.SFS" should not be
exceeded under any circumstances.
You must follow all operator and safety instructions, as well as all common
safety practices which reduce the likelihood or severity of physical injury.
Safety Standard: Comply with the Safety Standards of the American
National Standards Institute, ANSI B165.1 and ANSI B165.2 "Safety
Requirements-Power Brushes".
IMPORTANT:
A Safety Slip is included with each shipping package for power brushes. All operators should read and understand safety information thoroughly and completely before
using the brush. Keep the safety
slip with the brush. All operators
must read it.
WARNING:
Failure to observe safety rules
Inspection and Storage: Upon receipt, inspect brushes for damage, rust,
and deterioration. Store in original containers in a clean, dry location. Do
not allow distortion of brush filaments/components or foreign matter to
become lodged in brush face.
Dust and Fumes: Wear respiratory protection against this hazard
(see ANSI 288.2).
Brushing Problems: DO NOT ALLOW UNSAFE OPERATIONS TO
CONTINUE. Occasionally, due to worn bearings, a bent spindle, an
unusual application, operator abuse or inappropriate use, a brush may
fail. Do not continue to use a failed brush or one which is functioning
improperly (i.e., throwing filaments, out of balance, etc.), as this increases
the possibility for further brush failure and hazard of injury. The cause of
the failure should be evaluated and corrected immediately.
Protective Equipment: Appropriate protective equipment (such as full
face shields, respirator, etc.) must be used where a possibility of injury
exists that can be prevented by such equipment.
Before Starting Brush: Use eye protection and safety equipment.
Inspect brush for rust, damage, speed limit, etc. If no-load speed marked
on the power tool is higher than the brush speed limit, do not mount
brush. Inspect and jog machine to assure the brush is mounted properly
and securely, machine guards are in place, no vibration, etc. Run
machine at operating speed for at least one minute before applying workDO NOT STAND IN FRONT OF OR IN LINE WITH BRUSH.
Availability of ANSI Standards:
Contact – ANSI, 1430 Broadway, New York, NY 10018.
"This information for users is provided solely as a public service.
These recommendations are not necessarily complete for any particular application, and you should follow common sense safety
considerations. Federal, state or local laws or regulations must be
strictly obeyed, and
control over these
TA N I S
INCORPORATED
3660 Kettle Court East, Delafield WI 53018
CUSTOMER SERVICE:
1-800-234-7002
www.tanisbrush.com
262-646-9000 • FAX: 262-646-9005
TC 502 WI

Abrasive Nylon Disc Brushes

Transcription

Similar documents

cup brush

Twisted Brushes

Abrasive Brushes

ATB - Abrasive Brush Tools

Top 10 customers in terms of Transaction Amount

Nylox Brushes Catalog

american standard