User guide - Delta Dore

Installation and User Guide
TYXIA
Wireless receiver
TYXIA RF 651 - 2 channels
Warnings
Mounting
Presentation
• Carefully read these instructions prior to installation.
TYXIA RF 651 controls lightings, garage doors,
electric gates, or roller shutters.
• The unit must be installed in compliance with currently applicable standards.
• Always switch off the mains before installing or
servicing the unit.
Channel
1 LED
Channel
2 LED
Antenna
• Do not attempt to repair the unit yourself; an
after-sales service is available.
• The receiver power supply cable must only be
replaced by the manufacturer or an approved
agent.
Screw-mounting
Mounted on a wall using
the screws and pegs
supplied.
1
2
Buttons
• Check that the fastenings are suited to the surface
that the unit will be attached to (plasterboard,
brick, etc.).
Mounting by doublesided adhesive tape
• The diagrams provided are simplified for greater
clarity. The protective units and other accessories
required by the standards are not illustrated.
Mounting on the wall using the
double-sided adhesive tape
supplied.
Ensure that the surface on
which the tape is applied is
thoroughly clean before attaching the tape.
Electric
cable
Standard UTE NF C15-100 and good practice must
be complied with. Connected or nearby equipment
must not generate excessive interference (directive
2004/108/EEC).
Simple lighting mode (lighting)
Connection
Associating the
receiver
*2701909_Rev.1*
N
L
3A
3A
Blue
Black
Brown Grey
DELTA DORE
Bonnemain - 35270 COMBOURG - France
E-mail : [email protected]
brown
wire
blue
wire
brown
wire
blue
wire
black wire
grey wire
black wire
grey wire
Contact
switch 2
Mains
power
230 V
100 W
max.
Contact
switch 1
Device compliant with the requirements of directives:
R&TTE 1999/5/CE
100 W
max.
The maximum power directly controlled is limited to 100 W.
Above this limit, you must use a contact switch.
Because of changes in standards and equipment, the characteristics given in the text
and the illustrations in this document are not binding unless confirmed by Delta Dore.
Operation on the TYXIA RF 651
Pressing the button 1 or 2 of the receiver changes
the current status of the relevant channel (on or
off).
Technical characteristics
•
•
•
•
•
•
•
•
•
•
•
•
•
230 V, 50 Hz power supply, +/-10%
Class II insulation
Power consumption: 0.5 VA
Max. power per output: 3 A 230 Veff Cos ϕ
=1 or 100 W max. for lighting control,
Radio frequency 868 MHz (standard EN 300
220)
Radio range 100 to 300 metres outside,
variable depending on the associated equipment (the range can be altered depending
on the installation
conditions and the electromagnetic environment)
Number of transmitters that may be associated with the receiver: 8 max.
Automatic action: type 1.C (brownout)
Operating temperature: -5°C to +55°C
Storage temperature: -10 to +70°C
Dimensions: 54 x 102 x 19,5 mm
Protection index: IP 44 - IK 04
Install in an environment with normal pollution levels
Inverting the contact position of a relay
During an On command: the relay closes.
During an Off command: the relay opens.
To reverse the operation of a relay, press the corresponding button (1 or 2) on the receiver for 10
seconds.
Command sent Contact Inverted contact
ON
ON
OFF
OFF
OFF
ON
Simple lighting mode with an associated
TYXIA transmitter
The simple lighting mode can be controlled by a
TYXIA transmitter (transmitter switch, key ring
remote control, etc.).
On
Off
On
Off
On
OR Off
Either is possible, depending on the scenario
Troubleshooting
You cannot associate a transmitter with your
receiver.
The maximum number of transmitters to associate
with a receiver function is 8.
Check that this number has not been reached.
Lights only come on for 1 second each time a
button is pressed.
Pulse mode is enabled.
Put the unit into simple lighting mode (refer to the
“Association in simple lighting mode” chapter).
The receiver does not recognize the command
from a transmitter.
• The transmitter is not associated with the receiver.
• The receiver is still in association mode.
• The transmitter batteries are low.
No LED lights up on the receiver.
The receiver is not powered.
Check the receiver power supply line.
Each function of the receiver can record up to a
maximum of 8 associations (buttons, transmitters,
etc.).
Associating a
receiver
buttons with the
On the receiver, press the button of the channel
you want to associate until the LED flashes (~3
seconds). 2 possible choices.
Slow flashing: simple lighting mode
Rapid flashing: pulse mode.
Press the receiver button 1 or 2 to switch from one
rate of flashing to the other.
Select the slow flashing.
On the transmitter, press and hold down the
and
buttons together for about 5
seconds.
The buttons will light up, go out, then light up
again. Release.
Check that the receiver’s LED is no longer flashing.
The
and
transmitter buttons are associated with the receiver channel.
Associating a
receiver
button with the
One
button (scenario) can control different
receivers simultaneously (roller shutters, dimmer,
simple lighting, etc.).
On the receiver, set the appliance to the required
status (e.g. Light is off), press the button of the
channel you want to associate until the LED flashes (~3 seconds). 2 possible choices.
Slow flashing: simple lighting mode
Rapid flashing: pulse mode.
Press the receiver button 1 or 2 to switch from one
rate of flashing to the other.
Select the slow flashing.
On the transmitter, press and hold the
button
down for approximately 5 seconds.
The button will light up, go out then light up again.
Release.
Check that the receiver’s LED is no longer flashing.
The transmitter
button is associated with
the receiver channel.
Simple lighting mode with an associated
TYXAL detector
The simple lighting mode can be associated with a
TYXAL detector (opening, movement, technical,
etc.).
ON
Lights switch
on following
detection
OFF
Lights switch off
90 seconds after
the last detection
button with the
On the receiver, press the button of the channel
you want to associate until the LED flashes (~3
seconds).
2 possible choices.
Slow flashing: simple lighting mode
Rapid flashing: pulse mode.
Press the receiver button 1 or 2 to switch from one
rate of flashing to the other.
Select the slow flashing.
On the transmitter, press and hold the
button
down for approximately 5 seconds.
The button will light up, go out then light up again.
Release.
Check that the receiver’s LED is no longer flashing.
The transmitter
button is associated with
the receiver channel.
ON
Lights switch
on following
detection
OFF
Lights switch off
at the end of
detection
On the receiver, press the button of the channel
you want to associate until the LED flashes (~3
seconds).
On the receiver, press the Test key (emits a
beep).
Check that the receiver’s LED is no longer flashing.
The receiver can record up to a maximum of 8
associations (buttons, transmitters, etc.).
The detector is associated with the receiver
channel.
Simple lighting mode with an associated
TYXAL control unit
The simple lighting mode can be associated
with a TYXAL alarm control unit.
On the control unit, enable the
Maintenance mode (see control unit guide).
On the receiver, press the button of the
channel you want to associate until the LED
flashes (~3 seconds).
Slow flashing:
➪ alarm status transfer (channel 1)
- light on when the control unit is in surveillance
mode.
- light off when the control unit is not in surveillance mode.
➪ alarm transfer mode (channel 2)
- light on for 1.5 minutes in the event of an alarm
Rapid flashing:
➪ transfer of alarm surveillance enabling/disabling
- enabling the surveillance: lights flash once
- disabling the surveillance: lights flash twice
Press the button to pass from one rate of flashing
to the other.
Press the “Test” button of the control unit.
Check that the receiver’s LED is no longer flashing.
The control unit is associated with the receiver.
Simple lighting mode with an associated
TYDOM transmitter
The simple lighting mode can be associated with a
TYDOM transmitter.
TYDOM 3xx telephone transmitter
TYDOM 3xx enables the ON/OFF
feature to be operated remotely.
TYDOM 2xx multifunction remote control
TYDOM 2xx includes all the functions
of the TYXIA buttons:
To associate the receiver with the TYDOM, please
refer to the respective guides.
Removing all the associations with the
receiver in pulse mode or simple lighting
mode
Press and hold down the button of the channel to
remove.
The corresponding LED flashes after 3 seconds.
Hold down the button.
The relay reverses after 10 seconds and the LED
no longer flashes.
Hold down the button.
The LED flashes after 30 seconds; all the associations with the channel are removed.
Release the button.
Pulse mode (remote control switch, garage door, electric gate)
Operation on the TYXIA RF 651
Connection
Example 1 :
2 lighting outputs
Example 2 :
1 lighting output
1 open command output
N
L
Pressing the button 1 or 2 of the receiver changes
the current status of the relevant channel (on or
off).
Operating with the associated TYXIA or
TYDOM transmitter
3A
3A
Blue
Black
Brown Grey
brown
wire
blue
wire
black wire
black
wire
grey
wire
grey wire brown wire
blue wire
IMPORTANT : To use the receiver in pulse mode, it
must be associated with a transmitter.
The pulse mode can only be controlled by a
(TYXIA) or
(TYDOM 200) button.
Remote control
switch 2
or
Control of
an opening
(e.g.: a gate)
Remote
control
switch 1
Remote control
switch
The outputs 1 and 2 are supplied with power (230 V)
To control an opening, you must relay.
(status being modified)
Pressing the 1 or 2 button on the receiver changes
the current state (on or off).
On the receiver, press the button of the channel
you want to associate until the LED flashes (~3
seconds).
2 possible choices.
Slow flashing: simple lighting mode
Rapid flashing: pulse mode.
Press the receiver button 1 or 2 to move from one
rate of flashing to the other.
Select the rapid flashing.
On the transmitter, press and hold the
button
for 5 seconds.
The button will light up, go out then light up again.
Release.
Check that the receiver’s LED is no longer flashing.
The transmitter
button is associated with
the receiver channel in pulse mode.
Removing all the associations with the
receiver in pulse mode or simple lighting
mode
Press and hold down the button of the channel to
remove.
The corresponding LED flashes after 3 seconds.
Hold down the button.
The relay reverses after 10 seconds and the LED
no longer flashes.
Hold down the button.
The LED flashes after 30 seconds; all the associations with the channel are removed.
Release the button.
To associate a TYXIA RF 651 with a TYDOM 2xx,
please refer to the TYDOM 2xx guide..
Roller shutter mode
Connection
N
L
3A
3A
blue wire
Mains power
230 V
Roller shutter mode with an associated
TYXIA detector
Raising and lowering the roller shutters can be
associated with a TYXIA transmitter (transmitter
switch, key ring remote control, etc.).
Raising and lowering the roller shutters can be
associated with a TYXAL detector (opening, movement, technical, etc.).
Each function of the receiver can record up
to a maximum of 8 associations (buttons,
transmitters, etc.).
Blue
Black
Brown Grey
brown wire
Roller shutter mode with an associated
TYXIA transmitter
black wire
grey wire
Operation on the TYXIA RF 651
The buttons 1 and 2 raise or lower the roller shutters.
Raising or lowering
(choice of 1,
depending on the
scenario)
Associating the
buttons
On the receiver, simultaneously press the buttons 1
and 2 until they alternately flash (~3 seconds).
On the transmitter, simultaneously press and hold
the buttons
and
until the LED comes on.
Release.
Check that the receiver LEDs are no longer flashing.
The transmitter buttons
and
are associated
with the receiver.
Raising control
1
1
Press and
release
Press briefly
a 2nd time
The shutter rises
The shutter stops
1
Note: Pressing
briefly during the lowering
of the shutter commands the shutter to rise.
Lowering control
2
2
Press and
release
Press briefly
a 2nd time
2
The shutter lower
The shutter stop
Note: Pressing
briefly during the raising
of the shutter commands the shutter to lower.
OR Lower on
presence
detection
Raising or lowering
Lower
Raise
Neutral
Earth
- Once the receiver has been associated with a
transmitter, check that the Raise transmitter button controls the raising of the roller shutter.
If not, switch around the 2 raise/lower wires on
your receiver.
- The raise lower contacts are timed to 1 minute.
Raise on
presence
detection
Associating a
button (scenario)
One
button (scenario) can control different
receivers simultaneously (roller shutters, dimmer,
simple lighting, etc.).
On the receiver, set the appliance to the
required status (e.g. shutters lowered), press
the buttons 1 and 2 until they alternately flash
(~3 seconds).
On the transmitter, press and hold the
button down for approximately 5 seconds. The
LED will light up, go out, then light up again.
Release.
Check that the receiver LEDs are no longer
flashing.
The transmitter
button is associated with
the receiver.
On the receiver, simultaneously press the buttons 1
and 2 until they alternately flash (~3 seconds).
2 possible choices.
Slow flashing: a detected presence will cause the
roller shutters to rise,
Rapid flashing: a detected presence will cause the
roller shutters to lower,
Press the receiver button 1 to pass from one rate of
flashing to the other.
Rapid flashing: enabling the alarm will trigger the
lowering of the roller shutters, disabling the alarm
will have no action.
Press the receiver button 1 to pass from one rate of
flashing to the other.
Press the Test button of the control unit.
The control unit emits a beep.
Check that the receiver’s LED is no longer flashing.
The control unit is associated with the receiver.
Roller shutter mode with an associated
TYDOM transmitter
The simple lighting mode can be associated with a
TYDOM transmitter.
TYDOM 3xx telephone transmitter
TYDOM 3xx remotely raises
and lowers the roller shutters:
On = raise
Off = lower
TYDOM 2xx multifunction remote control
On the receiver, press the Test key (emits a beep).
Check that the receiver LEDs are no longer flashing.
The detector is associated with the receiver.
Roller shutter mode with an associated
TYXIA control unit
Raising and lowering the roller shutters can be
associated with a TYXAL alarm control unit.
Blinds are lowered
when the alarm
is enabled and OR
raised when it
is disabled.
Blinds are lowered
when the alarm
is enabled and
no change is made
when it is disabled.
Set the control unit to Maintenance mode (see its
guide).
On the receiver, simultaneously press the buttons 1
and 2 until they alternately flash (~3 seconds).
2 possible choices.
Slow flashing: enabling the alarm surveillance will
trigger the lowering of the roller shutters, disabling
the alarm will raise the shutters.
TYDOM 2xx includes all the
functions of the TYXIA buttons:
To associate the receiver with the TYDOM, please
refer to the respective guides.
Removing all the associations with the
roller shutters
Press and hold the receiver buttons 1 and 2
(after 3 seconds, the LEDs flash).
Hold the buttons down (approximately 30 seconds)
until the LEDs flash to confirm that all the receiver
associations are removed.