AlphaNet DSM3 Series DOCSIS® Status Monitor

Transcription

AlphaNet DSM3 Series DOCSIS® Status Monitor
Technical Manual
Effective: August 2011
Alpha Technologies
Power
®
AlphaNet DSM3 Series
DOCSIS® Status Monitor
Technical Manual
745-814-B8-001, Rev. A
Effective Date: August 2011
Copyright© 2011
Alpha Technologies, Inc.
member of The
GroupTM
NOTE:
Alpha denies responsibility for any damage or injury involving its enclosures, power supplies, generators,
batteries or other hardware, manufactured by Alpha or members of the Alpha Group, when used for an
unintended purpose, installed or operated in an unapproved manner, or improperly maintained.
NOTE:
Photographs and drawings in this manual are for illustrative purposes only and might not exactly match your
installation.
NOTE:
Review this manual before proceeding. If there are questions regarding the safe installation or operation of
this product, please contact Alpha Technologies or your nearest Alpha representative.
Contacting Alpha Technologies: www.alpha.com
or
For general product information and customer service (7 AM to 5 PM, Pacific Time), call
1-800-863-3930
For complete technical support, call
1-800-863-3364
7 AM to 5 PM, Pacific Time or 24/7 emergency support
To report errors in this document, send email to:[email protected]
745-814-B8-001, Rev. A (08/2011)
3
Contents
Safety Notes ........................................................................................................................................7
1.0 Introduction ....................................................................................................................................8
2.0 Overview......................................................................................................................................10
2.1
System Diagram ........................................................................................................10
2.2
Network Connectivity .................................................................................................11
2.3
System Configuration and Installation .......................................................................11
2.4
DSM3 Series Start-up and Reboot Routine ...............................................................12
3.0 Network Configuration .................................................................................................................13
3.1
Provisioning the DHCP Server with the MAC addresses...........................................13
3.2
The DOCSIS Configuration File .................................................................................14
3.2.1 Setting Modem Community Strings .....................................................................14
3.2.2 Setting SNMP Trap Destination Addresses..........................................................15
3.2.3 Sample DOCSIS Configuration File Entries .........................................................16
3.2.4 Proprietary Configuration File atidoc03.cfg ..........................................................17
3.2.5 Changing Default atidoc03.cfg Download Settings ..............................................17
3.3
Setting Communication Options ................................................................................18
4.0 Web Interface ..............................................................................................................................19
4.1
Local Web Server Access ..........................................................................................19
4.2
Remote Web Server Access ......................................................................................21
4.3
Navigating the Web Page ..........................................................................................22
4.3.1 Web Interface Security Levels .............................................................................23
4.4
Verifying Communication Parameters........................................................................23
4.5
Verifying Power Supply and Battery Parameters .......................................................24
4.6
Remote Self-tests via the Web Page .........................................................................24
4.7
Viewing HMS Alarm Status via the Web Page ...........................................................25
4.8
Viewing the Modem Event Log via the Web Page .....................................................26
4.9
Setting the I/O Controller via the Web Page ..............................................................26
4.10 Viewing and Configuring Power Supply settings via the Web Page ..........................27
5.0 Upgrading Firmware ....................................................................................................................28
5.1
Upgrading DSM3 Series Modem Firmware ...............................................................28
5.1.1 Identifying the Modem and Obtaining Firmware Files ..........................................28
5.1.2 Modem Firmware Upgrade SNMP Parameters ...................................................28
5.1.3 Upgrading Manually by Setting SNMP Parameters .............................................29
5.1.4 Upgrading via the DOCSIS Configuration File .....................................................29
6.0 Data Management .......................................................................................................................30
6.1
SCTE-HMS MIBs ......................................................................................................30
6.2
SCTE-HMS MIB Alarms .............................................................................................31
6.2.1 SCTE-HMS Configurable Alarms .........................................................................31
6.2.2 SNMP Traps .........................................................................................................34
6.2.3 General Power Supply Alarms .............................................................................36
6.3
The Alpha MIBs..........................................................................................................37
6.3.1 The Alpha MIB Structure ......................................................................................39
4
745-814-B8-001, Rev. A (08/2011)
Contents, continued
7.0 Installation ...................................................................................................................................40
7.1
Verifying Power Supply Device Address ...................................................................40
7.2
Installation / Replacement Procedure in XM2 ............................................................41
7.3
DPM Installation / Replacement Procedure ...............................................................43
7.4
DSM3x LEDs and Connections .................................................................................45
7.5
DSM3 LEDs and Connections ...................................................................................46
7.6
DPM Connections ......................................................................................................47
7.7
Connecting the RF Drop ............................................................................................48
7.8
Front Panel Connections ...........................................................................................48
7.9
Environmental and LA-P-SM Connections ................................................................49
7.9.1 Connecting the Battery Heater Mat Controller .....................................................49
7.10 Environmental Control MIBs .....................................................................................50
7.11 Configuring the Battery Heater Mat Controller ...........................................................52
7.12 Connecting the LA-P-SM ...........................................................................................53
7.12.1 Configuring the LA-P-SM .....................................................................................53
7.12.2 Simultaneous Usage, Environmental Control and LA-P-SM ................................53
8.0 Battery Sense Wire Kits...............................................................................................................53
8.1
36V Single and Dual Strings ......................................................................................54
8.2
48V Single and Dual Strings ......................................................................................55
9.0 Start Up and Verification ..............................................................................................................55
9.1
Initial Startup and Local Verification ...........................................................................56
To Verify Network Connectivity ........................................................................................56
9.2
Verifying Correct Hardware Interconnection ..............................................................56
9.3
Verifying Communications via the Headend ..............................................................56
9.4
System Status Indicators and Reset button ...............................................................58
9.4.1 Detailed LED Descriptions ...................................................................................58
9.4.2 Resetting the Transponder ...................................................................................60
9.5
Verifying Communications via the Headend ..............................................................60
10.0 MIB Parameters.........................................................................................................................61
10.1 Definitions and Settings .............................................................................................61
11.0 Specifications.............................................................................................................................65
12.0 Glossary ....................................................................................................................................67
13.0
Dual IP Mode .........................................................................................................................68
13.1 Overview ....................................................................................................................68
13.2 Web Comparison, Single IP Mode/Dual IP mode ......................................................69
13.3 Configuring Dual IP Mode ..........................................................................................70
13.3.1 atidoc03.cfg in Dual-IP Mode ...............................................................................72
13.3.2 Changing Default atidoc03.cfg Download Settings in Dual-IP Mode ...................72
13.3.3 Specifying atidoc03.cfg name and location via DHCP Tags ................................72
13.4 Dual IP SNMP Community Strings ............................................................................73
13.5 Security in Dual IP Mode ...........................................................................................73
745-814-B8-001, Rev. A (08/2011)
5
Figures
Fig. 1-1, AlphaNet DSM3x .......................................................................................................8
Fig. 1-2, AlphaNet DSM3 .........................................................................................................8
Fig. 1-3, AlphaNet DPM ...........................................................................................................8
Fig. 1-4, Side view, AlphaNet DSM3 Series.............................................................................9
Fig. 2-1, Representative System Arrangement ......................................................................10
Fig. 3-1, Locations of MAC Address Labels...........................................................................13
Fig. 3-2, Sample DOCSIS Configuration File ........................................................................16
Fig. 4-1, DSM3 Series Web Page..........................................................................................19
Fig. 4-2, Local Area Connection Properties Screen...............................................................20
Fig. 4-3, Internet Protocol (TCP/IP) Properties Screen .........................................................20
Fig. 4-4, Remote Web Server Home Page ............................................................................21
Fig. 4-5, DSM3 Series Site Map ............................................................................................22
Fig. 4-6, DSM3 Series Transponder Security Levels .............................................................23
Fig. 4-7, Communications Parameters ..................................................................................23
Fig. 4-8, Power Supply and Battery Parameters ...................................................................24
Fig. 4-9, Location of Start Button for Self Test .......................................................................24
Fig. 4-10, HMS Alarm Configuration ......................................................................................25
Fig. 4-11, Event Log Screen ..................................................................................................26
Fig. 4-12, Advanced I/O Controller Status Screen .................................................................26
Fig. 4-13, Advanced Power Supply Settings Screen .............................................................27
Fig. 6-1, Sample Raw SNMP Alarm Trap ..............................................................................34
Fig. 6-2, Sample Translated SNMP Alarm Trap .....................................................................34
Fig. 7-1, Removing the Inverter Module from the Power Supply ..........................................40
Fig. 7-2, The 18-pin Jumper ..................................................................................................41
Fig. 7-3, The 18-pin Jumper in place .....................................................................................41
Fig. 7-4, Connecting the Transponder to the Inverter Module ...............................................41
Fig. 7-5, Removing the Inverter Module from the Power Supply ...........................................42
Fig. 7-6, Removing the DPM Sheet Metal from the Inverter Module .....................................42
Fig. 7-7, The 18-pin Jumper in place .....................................................................................43
Fig. 7-8, The 18-pin Jumper ..................................................................................................43
Fig. 7-9, DPM Attached to Sheet Metal .................................................................................43
Fig. 7-10, DPM / IM Connection ............................................................................................43
Fig. 7-11, Completed Assembly .............................................................................................43
Fig. 7-12, DSM3 Series LEDs and Connectors .....................................................................44
Fig. 7-13, DSM3 LEDs and Connectors ................................................................................45
Fig. 7-14, DPM LEDs and Connections .................................................................................46
Fig. 7-15, Connecting the RF Drop ........................................................................................47
Fig. 7-16, System Interconnection Diagram ..........................................................................47
Fig. 8-1, 36V System, Single String .......................................................................................53
Fig. 8-2, 36V System, Dual String .........................................................................................53
Fig. 8-3, 48V System, Single String .......................................................................................54
Fig. 8-4, 48V System, Dual String .........................................................................................54
Fig. 9-1, Initial Web Page ......................................................................................................55
Fig. 9-2, General Tab Screen.................................................................................................56
Fig. 9-3, LED Functionality and Indications ...........................................................................57
Fig. 9-4, DSM3 Web Page, RF Power Level Indicators.........................................................59
Fig. 13-1, Simplified Block Diagram, Single IP Mode ............................................................68
Fig. 13-2, Simplified Block Diagram, Dual IP Mode ...............................................................68
Fig. 13-3, Web Page, Single IP DSM3 Series .......................................................................69
Fig. 13-4, Web Page, Dual IP DSM3 Series ..........................................................................69
Fig. 13-5, Dual IP Configuration Settings on Communications page of DSM3 Web Server .............. 71
Fig. 13-6, Dual IP Parameters on the General page of DSM3 Web Server ..........................71
6
745-814-B8-001, Rev. A (08/2011)
Tables
Table 3-1, Modem Community String Parameters .................................................................14
Table 3-2, Trap Distribution Addresses ..................................................................................15
Table 3-3, Transponder Communications Parameters ..........................................................18
Table 5-1, Modem Firmware Upgrade SNMP Parameters ....................................................28
Table 6-1, SCTE-HMS MIB Files ...........................................................................................30
Table 6-2, Binary to Hex Conversions for Alarm Settings ......................................................31
Table 6-3, Recommended Settings for DSM3 Series Analog Alarms ...................................32
Table 6-4, Recommended Settings for DPM Analog Alarms ................................................32
Table 6-5, Recommended Settings for Discrete Alarms ........................................................33
Table 6-6, SNMP Alarm Trap VarBinds and Explanations .....................................................35
Table 6-7, XM2 Major and Minor Alarms................................................................................36
Table 6-8, Alpha MIB Hierarchy .............................................................................................38
Table 13-1, Single IP Mode versus Dual IP Mode .................................................................68
Table 13-2, Enabling Dual IP Mode .......................................................................................70
Table 13-3, CPE Transponder Settings .................................................................................70
Table 13-4, Data Access Key Parameters .............................................................................73
Table 13-5, Data Access Key Parameters .............................................................................73
Table 13-6, Secure Access Table Parameters .......................................................................74
Safety Notes
Review the drawings and illustrations contained in this manual before proceeding. If there are any questions regarding
the safe installation or operation of the system, contact Alpha Technologies or the nearest Alpha representative. Save this
document for future reference.
To reduce the risk of injury or death and to ensure the continued safe operation of this product, the following symbols have
been placed throughout this manual. Where these symbols appear, use extra care and attention.
ATTENTION:
The use of ATTENTION indicates specific regulatory/code requirements that may affect the placement of
equipment and /or installation procedures.
NOTE:
A NOTE provides additional information to help complete a specific task or procedure.
CAUTION!
The use of CAUTION indicates safety information intended to PREVENT DAMAGE to material or
equipment.
WARNING!
WARNING presents safety information to PREVENT INJURY OR DEATH to the technician
or user.
745-814-B8-001, Rev. A (08/2011)
7
1.0 Introduction
The AlphaNet DSM3 Series Embedded DOCSIS Transponder allows monitoring of Alpha power supplies through
existing cable network infrastructure. Advanced networking services provide quick reporting and access to critical
powering information.
The DSM3 Series utilizes Simple Network Management Protocol (SNMP) and standard Management Information
Bases (MIBs) to provide network status monitoring and diagnostics. A Web interface enables authorized
personnel direct access to advanced diagnostics using a common Web browser. No custom software is required.
This manual addresses the three models of the DSM3 Series. The table below compares the differences between
the transponder models.
Model
DSM3x (E)
DSM3 (E)
DPM (E)
Part Number
746-097-23
746-097-24
746-097-25
Supported Power Supplies
XM2, XM2-HP, XM2-VP, GMX, VMX
XM2, XM2-HP, XM2-VP, GMX, VMX
XM2-300HP
Capacity
5 power supplies (plus generator)
1 power supply
1 power supply
1 & 2 Battery Strings
Yes
Yes
1 battery (2 for added runtime)
3 & 4 Battery Strings
Yes
No
No
Tamper Switch
Yes
Yes
Yes
Environmental Control / LA-P-SM
Yes
No
Yes
COM Port (AlphaBus)
Yes
No
No
Ethernet Port
Yes
Yes
Yes
2 x 9 Interconnection Header
Alpha p/n 540-286-19
Alpha p/n 540-286-19
Alpha p/n 540-581-19
DSM3x 2 x 9 header
(Alpha p/n 540-286-19)
Fig. 1-1, AlphaNet DSM3x Series
DSM3 2 x 9 header
(Alpha p/n 540-286-19)
Fig. 1-2, AlphaNet DSM3
DPM 2 x 9 header
(Alpha p/n 540-581-19)
Fig. 1-3, AlphaNet DPM
Primary Features:
•
•
•
•
•
•
•
•
•
10/100 Mbps auto-negotiating standard Ethernet interface
Supports SNMPv1, v2c
Extensive power supply diagnostic MIBs
Embedded Web server for direct diagnostics
Environmentally hardened DOCSIS cable modem and transponder
Local Ethernet port provides technician on-site access to extensive power supply diagnostics*
Angled RF port reduces cable bend radius
Diagnostic LEDs
North American or Euro DOCSIS available (Euro models in parentheses)
* Ethernet port also available for connecting external CPE devices
8
745-814-B8-001, Rev. A (08/2011)
1.0 Introduction
Intelligent CableUPS
Interface
Standard — Single
Microcontroller Cable
Modem Design
Power Supply Interface (GMX,
VMX Models)
RF Port
Fig. 1-4, Side view, AlphaNet DSM3 Series
745-814-B8-001, Rev. A (08/2011)
9
2.0 Overview
2.1
System Diagram
10 SNMP-based Network Management System
2 DSM3
Series
1 Power Supply
5 Coax/HFC Network
6 CMTS
7 TCP/IP Network
4 Local Computer
3 External Generator
7 DHCP Server
8 TFTP Server
9 TOD Server
11 Web Browser
Fig. 2-1, Representative System Arrangement
10
1
All power supply data is stored in the power supply inverter module's class information base (CIB) tables in the power supply.
This data is accessible directly via the power supply’s smart display (see the power supply’s technical manual for details).
The CIB tables are the source of the transponder’s data.
2
The DSM Series contains both SCTE-HMS Management Information Base (MIBs) and the proprietary Alpha MIB tables. The
SCTE-HMS MIBs are industry standard MIB tables that store power supply, battery and generator data from the CIB tables
(See Section 7.0, Data Management). The Alpha MIB contains all the data of the SCTE-HMS MIBs plus additional power
supply settings and values as well as DSM3 Series configuration values.
3
An external generator or additional power supplies may be connected through the COM (AlphaBus) port permitting
monitoring locally through the Ethernet connector or remotely via the Web page or SNMP-based Network Management
System.
4
Power supply and transponder parameters can be monitored and set locally using a personal computer and a standard
Ethernet cable.
5
The DSM3 Series transmits data via its cable modem directly over the Coax or Hybrid Fiber Coax network.
6
The Cable Modem Termination System (CMTS) is the bridge between the cable network and the TCP/IP network. The DSM3
Series’ cable modem communicates directly with the CMTS.
7
The Dynamic Host Control Protocol (DHCP) server needs to be provisioned with the DSM3’s cable modem RF MAC Address
and the MAC Address needs to be assigned a DOCSIS Configuration File.
8
The DOCSIS Configuration File and firmware files should be available in the Root Directory of the Trivial File Transfer
Protocol (TFTP) Server.
9
The Time of Day (TOD) Server provides the cable modem with the current date and time via the SNTP protocol.
10
A Network Management System (NMS) or MIB Browser allows remote monitoring of parameter values and changing of
settings in SNMP MIB tables. SCTE-HMS and Alpha MIBs must be installed in the browser. Alarms and traps can be set and
monitored.
11
The power supply and generator may be accessed remotely through the transponder's Web page by placing its IP address
into a standard Internet Web browser.
745-814-B8-001, Rev. A (08/2011)
2.0 Overview
2.2
Network Connectivity
The DSM3 Series cable modem must be recognized by the CMTS as a valid device to be assigned an IP
address from the DHCP server, to locate the TFTP and TOD servers and to communicate with the SNMP
management server (trap receiver).
Data from both the cable modem and power supply are accessed and managed through the modem’s
IP address on the secure private modem network. The transponder is not accessible from the public
Customer Premises Equipment (CPE) network. Consequently, the Network Management System (NMS)
that monitors the power supplies must have access to the same private modem network.
CMTS and system vendors use different security methods to insure network integrity, but common
considerations are:
2.3
•
MAC filtering may have to be modified to allow RF MAC registration of addresses starting with
00:90:EA - North American or 00:03:08 - Euro models.
•
For SNMP access, UDP ports 161 and 162 must not be blocked.
•
For TFTP access, port 69 must not be blocked.
•
For HTTP access, port 80 must not be blocked.
•
For SNTP access, port 37 must not be blocked.
•
Firewalls must allow TFTP, DHCP, SNMP and TOD communication to the cable modem.
•
If the address of the TFTP or TOD server is different than the DHCP server, the response from the
DHCP server must contain the TFTP and TOD addresses.
System Configuration and Installation
NOTE:
Before installation, read all of the “System Overview” Sections.
DSM3 Series installation and setup is comprised of three basic steps:
1. Configuring the Network: Provisioning the DHCP Server with the transponder’s MAC Address and
assigning it a DOCSIS Configuration File.
2. Setting Options: The DSM3 Series is designed for out-of-the-box, "plug and play" operation, but
non-default settings such as SNMP trap destination addresses may be required for the Network
Management System (NMS). SNMP trap addresses can be set automatically via the DOCSIS
Configuration File per RFC 4639, while DSM3 Series proprietary options may be set through type-11
TLV entries. The SCTE-HMS and Alpha MIBs may need to be compiled into a MIB browser before it
can be used to monitor or set transponder and power supply parameters.
3. Field Installation of the DSM3 Series into the power supply, connecting the battery sense wire
harnesses and verifying operation.
These steps can be performed independently of one another. However, configuring the network prior
to field installation will allow the installation to be verified while personnel are still on-site. Performing
field installation before network configuration and before the installation can be verified, might result in
additional field service calls to correct mistakes.
Carefully read the following section in order to understand the dependencies within the system before
performing system configuration or hardware installation.
745-814-B8-001, Rev. A (08/2011)
11
2.0 Overview
DSM3 Series Start-up and Reboot Routine
TCP/IP Network
2.4
TFTP Server
5
Network Management System
TOD Server
4
MIB Browser
DHCP Server
3
Web Browser
Routers
Switches
Firewalls
CMTS
HFC Network
2
6
DSM3 Series
1
Power Supply
7
Local Laptop
The above diagram, read left to right, indicates the order of operations as the transponder comes online.
There are certain conditions that must exist for each step to occur, resulting in successful data monitoring and
management. The numbers below correspond to the numbered arrows above.
LEDs and Indications
Ref #
12
Communications State
ALM/RDY
DS
REG
RF
COM
1
Transponder Initializing/Searching
for Downstream DOCSIS channel
OFF and ON (Green)
OFF and ON
OFF
OFF
OFF and ON
2
DOCSIS Channel locked Completing upstream and network
registration
OFF and ON (Green)
ON
OFF and ON
ON
OFF and ON
3
to
5
Online - Registration Complete
OFF and ON (Green)
ON
ON
ON
OFF and ON
6
to
7
DSM3 Series fully functional
OFF and ON (Green)
ON
ON
ON
Bursts
745-814-B8-001, Rev. A (08/2011)
3.0 Network Configuration
3.1
Provisioning the DHCP Server with the MAC addresses
On the DHCP server, assign the cable modem’s RF MAC address with a DOCSIS Configuration File
to set modem communication options. (See Section 3.2 for instructions on how to create a DOCSIS
Configuration File).
The RF and CPE MAC addresses are located in two places on the DSM3 Series and on the packing slip,
see below.
Identifier label
*0900EA003056*
*0900EA003057*
Cable Modem
and CPE MAC
address label
Fig. 3-1, Locations of MAC Address labels
745-814-B8-001, Rev. A (08/2011)
13
3.2
The DOCSIS Configuration File
A cable modem’s DOCSIS Configuration File is a type-length-value (TLV) file that contains important
operational parameters as defined by the DOCSIS standards. It provides certain settings for the cable
modem. In addition to standard entries, settings in the DOCSIS Configuration File should include the
modem’s community strings and, if an upgrade is necessary, firmware upgrade parameters. Place the
configuration file in the TFTP root directory.
To build a DOCSIS Configuration File use a DOCSIS TLV editor program.
See the example Configuration File in Section 3.2.3.
NOTE:
The modem community strings should be set in the DOCSIS Configuration File. Failure to set
community strings will result in a less secure system. For automatically updating modem firmware
with the DOCSIS Configuration File, see Section 5.1.
3.2.1 Setting Modem Community Strings
Set the modem community strings with the DOCSIS Configuration File by including the following
SNMP parameters:
MIB Parameter
Object ID
Description
Value
docsDevNmAccessIp
1.3.6.1.2.1.69.1.2.1.2
The IP address (or subnet) of the
network management station
e.g. 10.20.30.0
docsDevNmAccessIpMask
1.3.6.1.2.1.69.1.2.1.3
The IP subnet mask of the network
management stations
e.g. 255.255.255.0
docsDevNmAccessCommunity
1.3.6.1.2.1.69.1.2.1.4
The community string matched to this
IP/Mask entry
alphanumeric string
docsDevNmAccessControl
1.3.6.1.2.1.69.1.2.1.5
The level of access granted
1= none
2= read only
3= read/write
docsDevNmAccessInterfaces
1.3.6.1.2.1.69.1.2.1.6
Specifies the set of interfaces from
which requests from this NMS will be
accepted
0x40 : Cable interface (typical)
0x80 : Ethernet interface
0xC0 or 0x00 : Both interfaces
docsDevNmAccessStatus
1.3.6.1.2.1.69.1.2.1.7
Controls and reflects the status of rows
in this table
4
Table 3-1, Modem Community String Parameters
14
745-814-B8-001, Rev. A (08/2011)
3.2
The DOCSIS Configuration File, continued
3.2.2 Setting SNMP Trap Destination Addresses
Set the SNMP Trap Destination addresses via the DOCSIS Configuration File by including the
following SNMP parameters:
MIB Parameter
Object ID
Description
Value
docsDevNmAccessIP
1.3.6.1.2.1.69.1.2.1.2
IP address of trap destination, e.g. NMS
server
e.g. 10.20.30.40
1.3.6.1.2.1.69.1.2.1.3
Must be set to 255.255.255.255 per RFC
4639
255.255.255.255
docsDevNmAccessCommunity
1.3.6.1.2.1.69.1.2.1.4
Community string used by NMS to query
transponder
alphanumeric string
docsDevNmAccessControl
1.3.6.1.2.1.69.1.2.1.5
Level of SNMP access to DSM3 Series
from IP address specified in
4= Read/Only plus Trap
5= Read/Write plus Trap
6= Trap only, no SNMP access
docsDevNmAccessInterfaces
1.3.6.1.2.1.69.1.2.1.6
Specifies the set of interfaces from which
requests from this NMS will be accepted
0x40 : Cable interface (typical)
0x80 : Ethernet interface
0xC0 or 0x00 : Both interfaces
docsDevNmAccessStatus
1.3.6.1.2.1.69.1.2.1.7
Controls and reflects the status of rows
in this table
4
Table 3-2, Trap Destination Addresses
NOTE:
As an alternative to the docsDevNmAccessTable, SNMP Trap Destination Addresses may be set
through the DSM3 proprietary MIB. See Table 3-3.
745-814-B8-001, Rev. A (08/2011)
15
3.2
3.2.3 Sample DOCSIS Configuration File Entries
A
SNMP MIB Object (11) [Len=21]:docsDevNmAccessStatus.1/4
SNMP MIB Object (11) [Len=21]:docsDevNmAccesslp.1/10.56.21.0
SNMP MIB Object (11) [Len=21]:docsDevNmAccesslpMask.1/255.255.255.0
SNMP MIB Object (11) [Len=25]:docsDevNmAccessCommunity.1/"RW STRING"
SNMP MIB Object (11) [Len=25]:docsDevNmAccessInterfaces.1/"@"
SNMP MIB Object (11) [Len=21]:docsDevNmAccessControl.1/3
B
SNMP MIB Object (11) [Len=21]:docsDevNmAccessStatus.2/4
SNMP MIB Object (11) [Len=21]:docsDevNmAccesslp.2/10.20.30.40
SNMP MIB Object (11) [Len=21]:docsDevNmAccesslpMask.2/255.255.255.255
SNMP MIB Object (11) [Len=25]:docsDevNmAccessCommunity.2/"RW Trap string"
SNMP MIB Object (11) [Len=25]:docsDevNmAccessInterfaces.2/"@"
SNMP MIB Object (11) [Len=21]:docsDevNmAccessControl.2/5
C
Software Upgrade Filename(9) [Len=24]:"ModemFirmwareFile.bin"
SNMP MIB Object (11) [Len=20]:docsDevSwAdminStatus.0/2
D
Software Upgrade TFTP Server (21) [Len=4]:10.56.48.15
E
Manufacturer Code Verification Certificate (32) [Len=254]: 30 82 03 1A 30 82...
Manufacturer Code Verification Certificate (32) [Len=254]: 04 0A 13 11 41 4D...
Manufacturer Code Verification Certificate (32) [Len=254]: 04 0C 30 0A 06 01...
Manufacturer Code Verification Certificate (32) [Len=36]: 11 A3 41 A6 A7 D9....
Fig. 3-2, Sample DOCSIS Configuration File
Legend:
A
Sets Read-Write Community string. Set the IP address, Netmask and community string to fit your system.
B
Sets the IP address of where the SNMP traps will be sent. This is typically set to match the IP address of the Network
Management's System Server.
C
D
E
Sets firmware download parameters.
Specifies the IP Address of the TFTP server used for upgrading firmware.
Sets Code Verification Certificate (CVC) for firmware upgrade security per the DOCSIS specification.
NOTE:
DOCSIS configuration files vary from system to system. Take into consideration your company's policies, and
test the file on a local system prior to widescale deployment.
In previous versions of the DSM product line, an additional configuration file (also known as a Setup File)
could be used for distributing custom Alpha MIB settings to all DSMs on a network. This is still the case,
with the only difference being the name of the file, which for the DSM3 Series is atidoc03.cfg. It may be
used if preferred, but is not required.
16
745-814-B8-001, Rev. A (08/2011)
3.2
3.2.4 Proprietary Configuration File ‘atidoc03.cfg’
The DSM3 Series will attempt to download a TLV-formatted file ‘atidoc03.cfg’ from the modem’s
provisioning TFTP server at startup and every 24 hours thereafter. The atidoc03.cfg proprietary
configuration file is optional and provides an alternative method to the modem’s DOCSIS
configuration file for deploying Alpha proprietary SNMP MIB parameters to field-installed DSM3 Series
transponders.
The atidoc03.cfg file should be used if the following conditions are true:
1. Non-default settings, such as SNMP Trap Destination Addresses need to be distributed to all
DSM3 Series transponders.
2. The operator does not desire to place Alpha-proprietary parameters into the modem’s DOCSIS
configuration file.
NOTE:
The recommended method for setting the SNMP trap address(es) is through the modem DOCSIS
configuration file (See section 3.2). Alpha-proprietary parameters may also be set through the modem’s
DOCSIS configuration file, eliminating the need for the atidoc03.cfg proprietary configuration file.
To build the atidoc03.cfg file, enter the desired SNMP OIDs and values from the Alpha MIB into a
TLV file as TLV type-11 entries using a TLV editor as TLV type-11 (See table 3-3). The DSM3 Series
proprietary configuration Setup file must be named “atidoc03.cfg” and placed in the root directory of
the TFTP server. DSM3 settings are updated according to values defined in this file at startup and
after every 24 hours of operation.
Sample atidoc03.cfg Entries:
SNMP MIB Object (11) [Len = 24]: atiMgmtSnmpTrapAddress.1 / 10.20.30.40
SNMP MIB Object (11) [Len = 24]: atiMgmtSnmpTrapAddress.2 / 10.20.30.50
SNMP MIB Object (11) [Len = 23]: atiMgmtSysTamperPolarity.0 / 1
3.2.5 Changing Default atidoc03.cfg Download Settings
By default the DSM3 Series will download the atidoc03.cfg file from the provisioning TFTP server
every 24 hours, but these settings can be adjusted per the tables below by placing the respective
SNMP varbinds into the modem’s DOCSIS configuration file.
Parameter
Type
Description
Value
atiMgmtSysDownloadConfigName
1.3.6.1.4.1.926.1.3.2.1.9.0
Alphanumeric
String
Name of proprietary
configuration file
"atidoc03.cfg"
(Default)
atiMgmtSysDownloadReCfgTime
1.3.6.1.4.1.926.1.3.2.1.13.0
Integer
Download interval for
atidoc03.cfg (hours)
24 (Default)
Search
Order
745-814-B8-001, Rev. A (08/2011)
Parameter
Type
Description
Value
1
atiMgmtSysDownloadConfigAddress
OID 1.3.6.1.4.1.926.1.3.2.1.10.0
IP Address
Overrides Default
Location
0.0.0.0 (Default)
2
docsDevServerConfigTftpAddress
1.3.6.1.2.1.69.1.4.11.0
IP Address
Default location (No
change necessary)
CM's TFTP
Server Address
3
docsDevSwServerAddress
1.3.6.1.2.1.69.1.3.7.0
IP Address
Set via DOCSIS
configuration file
Configurable
4
Software Upgrade Server
IP Address
Set via DOCSIS
configuration file
Configurable
17
3.3
Setting Communication Options
Communications Settings may be changed through the Alpha MIB remotely using an SNMP MIB browser
or automatically by placing the SNMP parameters into the DOCSIS config file.
See Section 6, Data Management for an explanation of the Alpha MIB.
NOTE:
Before setting options, verify UDP ports 37, 69, 161, 162 and TCP port 80 are not blocked.
SNMP Parameter
Type
Description
Value
atiMgmtSnmpTrapOnNormal
OID: 1.3.6.1.4.1.926.1.3.1.5.1.0
Integer
Send SNMP trap when alarmed
condition returns to normal state
1 = Disabled
2 = Enabled (Default)
atiMgmtSysDownloadReCfgTime
OID: 1.3.6.1.4.1.926.1.3.2.1.13.0
Integer
Download interval for DSM3 Seriesspecific items in modem config file
(hours)
24 (Default)
atiMgmtSysSnmpTimeout
OID: 1.3.6.1.4.1.926.1.3.1.5.3.0
Integer
Time DSM3 Series will wait before reset
if SNMP traffic is not detected (minutes)
1440 (Default)
Note: if set to zero, watchdog will be disabled.
atiMgmtSysHttpAccess
OID: 1.3.6.1.4.1.926.1.3.2.2.4.1.0
Integer
HTTP Web Server
1 = Disabled
2 = Enabled (default)
See Section 10.0 for complete parameter definitions.
Table 3-3, Transponder Communications Parameters
NOTE:
The DSM3 Series will inherit the cable modem community string settings provided by the DOCSIS
Configuration File.
18
745-814-B8-001, Rev. A (08/2011)
4.0 Web Interface
Overview
The DSM3 Series power supply transponder provides an embedded Web server interface to allow
operations personnel the ability to connect locally or remotely via TCP/IP over Ethernet with a laptop/
computer to verify the status of common data points and to configure various operating parameters.
4.1
Local Web Server Access
The DSM3 Series transponder’s Ethernet port (comparable to the “Craft” port on some transponder
models) will typically be used as a local connection point allowing the user to connect directly to the
DSM3 Series Web server interface to verify/configure common communication parameters and view
power supply status and battery values. The Ethernet port on the DSM3 Series is a fully functional
standard Ethernet port, capable of providing all the functionality of any standard Ethernet connection.
To access the DSM3 Series transponder Web server locally utilizing a Web browser, follow the procedure
outlined below:
1. Connect a standard Ethernet cable (CAT5) between the DSM3 Series transponder Ethernet port (ETH)
and a laptop or computer’s network interface port.
2. Launch a Web browser.
3. Enter the transponder's default IP address (192.168.100.1) into the Web browser’s address field.
4. The transponder’s Web server home page will appear (Fig. 4-1). Note: For the DSM3 Series, this
may take up to 45 seconds when the transponder is initially powered up with no RF connection.
®
AlphaNetTM DOCSIS Status Monitor
General
HMS Alarms
Advanced Settings
APPS
History
Print
Print
Communications
Configuration
SysUpTime
Firmware Version
2IP US
7 days 11H:13m:17s
4.4.6.0_02.00_NA
CM
CPE Transponder
MAC Address
00:90:EA:00:30:84
00:90:EA:00:30:85
IP Address
192.168.1.124
192.168.1.120
CM Tx (dBmV)
42.0
41.0
+50
0
CM Rx (dBmV)
3.2
-20
SNR (RxMER)
55
60
3.2
-15
-10
15
10
20
44.2
SET
System Name
Alpha
System Location
Bellingham
System Contact
John Doe
Common Logical ID
DSM3
Power Supplies
Device 1
Model
ALPHA / XM2
Firmware
7.03.0
Major Alarm
OK
Minor Alarm
Inverter Status
Tamper
OK
OFF
Closed
Self Test
Start Test
Time Since Last Standby
Last Standby Duration
Total String Voltage (V)
41.60
Temperature 1 (°C)
15
Input Voltage (V)
124.80
Output Voltage (V)
Output Current 1 (A)
89.00
1.00
Status
Actstate
Mode
Temperature
Hysteresis
Timer
Countdown
Environmental Controller
Contact Open
Closed
Heater
24
2
1
0
LAP
Not Installed
Not Installed
Batteries
Battery 1 (V)
Battery 2 (V)
Battery 3 (V)
String 1
13.90
13.95
14.00
String 2
13.95
14.00
13.90
Copyright © 2010, AlphaTechnologies Inc., All Rights Reserved
Fig. 4-1, DSM3 Series Web Page
(data values shown for illustration purposes only)
745-814-B8-001, Rev. A (08/2011)
19
4.0 Web Interface
4.1
Local Web Server Access, continued
NOTE:
If you are unable to view the home page of the DSM3 Series using IP Address 192.168.100.1, the network
configuration on the computer that is being used to connect to the DSM3 Series transponder may require a
temporary static IP address to be configured.
Use the following procedure to configure a static IP
address on a laptop or computer:
1. Click on the “start” button (lower left button on most
Windows® computers).
2. When the window pops up, click on “Control Panel”
(usually about half the way down the second
column).
3. Click on "Network Connections."
4. Right-Click on "Local Area Connection" to open
menu box.
5. Click on the bottom option "Properties."
6. You will see a dialog box much like Fig. 4-2; scroll
down to the entry “Internet Protocol (TCP/IP)” and
then click on the “Properties” button.
Fig. 4-2, Local Area Connection
Properties Screen
7. The Internet Protocol (TCP/IP) Properties
dialog box will open (Fig. 4-3). Enter the
values as shown. Record the existing IP
address and Subnet mask in order to later
return the computer to its original state.
8. Click on the “OK” button and try to connect
to the DSM3 Series transponder once again
using 192.168.100.1 in your Web browser.
9. Once completed with the DSM3 Series
local Ethernet port connection, repeat the
above steps 1 to 6 to restore the computer's
network configuration back to the original
settings.
Fig. 4-3, Internet Protocol (TCP/IP)
Properties Screen
20
745-814-B8-001, Rev. A (08/2011)
4.0 Web Interface
4.2
Remote Web Server Access
To remotely access the DSM3 Series transponder Web server utilizing a Web browser, follow the
procedure outlined below:
NOTE:
For Web server (HTTP) access, port 80 must not be blocked.
1. Connect the laptop or computer’s network interface port to the company’s Ethernet network.
2. Open a Web browser.
3. Enter the DSM3 Series' designated IP address (e.g., 192.168.1.124) into the Web browser’s address
field.
4. The DSM3 Series transponder’s Web server home page will appear (Fig. 4-4).
®
General Configuration
General
HMS Alarms
Advanced Settings
APPS
HISTORY
Print
Communications
Configuration
SysUpTime
Firmware Version
2IP US
7 days 11H:13m:17s
4.4.6.0_02.00_NA
CM
CPE Transponder
MAC Address
00:90:EA:00:30:84
IP Address
192.168.1.124
00:90:EA:00:30:85
192.168.1.120
CM Tx (dBmV)
42.0
41.0
+50
0
CM Rx (dBmV)
3.2
-20
SNR (RxMER)
55
60
3.2
-15
-10
15
10
20
44.2
System Name
Alpha
System Location
Bellingham
System Contact
John Doe
Common Logical ID
DSM3
SET
Power Supplies
Device 1
Model
ALPHA / XM2
Firmware
7.03.0
Major Alarm
OK
Minor Alarm
Inverter Status
Tamper
OK
OFF
Closed
Self Test
Start Test
41.60
Temperature 1 (°C)
15
Input Voltage (V)
124.80
Output Voltage (V)
89.00
1.00
Status
Actstate
Mode
Temperature
Hysteresis
Timer
Countdown
Contact Open
Closed
Heater
24
2
1
0
LAP
Not Installed
Not Installed
Batteries
Battery 1 (V)
Battery 2 (V)
Battery 3 (V)
String 1
13.90
13.95
14.00
String 2
13.95
14.00
13.90
copyright © 2010, AlphaTechnologies Inc., All Rights Reserved
Fig. 4-4, Web Server Home Page
745-814-B8-001, Rev. A (08/2011)
21
4.0 Web Interface
4.3
Navigating the Web Page
Once the Web page has been successfully accessed, the operator is able to select a link on the header
bar and the page specific to the topic will open enabling real-time data to be observed.
The header bar has links for the following menu items:
General
Alarms
Settings
General HMS
HMS
Alarms Advanced
Advanced
Settings
Communications
Transponder Model
Configuration
SysUpTime
Firmware Version
CM MAC Address
IP Address
CM Tx (dBmV)
CM Rx (dBmV) SNR
(RxMER)
System Name
System Location
System Contact
Common Logical ID
Power Supplies
Model
Firmware
Major Alarm
Minor Alarm
Charger Mode
Input Voltage (V)
Inverter Status
Self Test
Start Test
Tamper
Output Voltage (V)
Batteries
Battery Temperature 1 (ºC)
String 1
Generator
Firmware
Generator Status
Major Alarm
Minor Alarm
Self Test
Start Test
APPS
Property Tree
Parameter OID
PS Device 1
psOutputVoltage.1
psInputVoltage.1
psTotalStringVoltage.1
psPowerOut.1
psFrequencyOut.1
psStringChargeCurrent.1.1
psStringFloat.1.1
psStringFloat.1.2
psOutputCurrent.1.1
psTemperature.1.1
psBatteryVoltage.1.1.1
Discrete Table
Parameter OID
PS Device 1
psInverterStatus.1.1
psMajorAlarm.1.1
psMajorAlarm.1.2
psMinorAlarm.1.1
psMinorAlarm.1.2
psTamper.1.1
psTamper.1.2
GENERATOR
genGeneratorStatus.8.1
genGeneratorGasHazard.8.1
genWaterIntrusion.8.1
genPadShear.8.1
genEnclosureDoor.8.1
genCharger.8.1
genFuel.8.1
genOil.8.1
genMinorAlarm.8.1
genMajorAlarm.8.1
TRANSPONDER
commonCraft Status.0.1
tibControlMode.1.1
tibControlMode.1.2
tibControlMode.1.3
Print
Print
HISTORY
COMMUNICATION CONFIGURATION
NETWORK PROVISIONING
CM Transponder Model
MAC DHCP/Static Status
SysUpTime
IP Subnet Mask Gateway
TOD Server
TFTP Server
DHCP Server
Lease Duration
Lease Expires
Configuration File
Config Download Timer (Hours)
DOCSIS
Downstream / Upstream Frequency (MHz)
Modulation Lock Status Power (dBmV)
Channel ID Symbol Rate (Msym/sec)
SNR (RxMER) CER T3 Timeouts T4 Timeouts
SNMP
docsDevNmAccessTable
Alpha Proprietary MIB
SNMP Trap 1
SNMPTrap 2
SNMP Trap 3
SNMP Trap 4
SNMP Trap
String Trap on Normal Trap
Send Count SNMP TimeOut (Minutes)
MISCELLANEOUS
Data Bus Size
DocsDev Event Log
RESET LOG
docsDevEvFirstTime
docsDevEvLastTime
docsDevEvCounts
docsDevEvLevel
docsDevEvId
docsDevEvText
POWER SUPPLY CONFIGURATION
Power Supply Model
Firmware Version
AC Line Mode
Major Alarm
Minor Alarm
SELF TEST
Self Test
Start Test
Test Countdown (Days)
Test Duration (Days)
Test Interval (Days)
INPUT Input Voltage (V)
Input Freq (Hz)
Input Current (A)
Tap Switch
BATTERY CHARGING
Battery String Voltage (V)
Charger Mode
Charger Current (A)
Charger Current Limit (A)
Charger Enable
Charger Accept Voltage (V/C)
Charger Float Voltage (V/C)
Batt Capacity (AH)
Charger Temperature
Compensation (mV)
Low Voltage Cutoff (V)
POWER SUPPLY CONFIGURATION (cont'd)
INVERTER
Inverter Enable
Standby Events
Total Inverter Run Time (Days)
Total Time Inverter In Standby (Hours)
OUTPUT
Output 1 Current (A)
Output Voltage (V)
Output Power Apparent (VA)
Output Power Real (Watts)
Percent Load (%)
PIM Option Installed
Output 1 Reset
Output Over-Current Tolerance (mSec)
Output 1 Over-Current Trip Level (A)
N+1 In Use
N+1 Valid Retry Delay (Seconds)
Retry Limit
ADVANCED GENERATOR
STATUS
Firmware Version
Generator Status
Time Since Last Engine Run
Last Engine Run Duration
Engine Enable/Disable
Engine Run Time (dHR)
ENGINE STATUS / ALARMS
Reset Latched Alarms
AC Line Status
AC Line Voltage (Vac)
DC Bus Status
DC Bus Voltage (Vdc)
Over Voltage
Self Test Alarm
Self Test
Start Test
Test Countdown (HR)
Low Ignition Battery
Ignition Battery Voltage (Vdc)
SETTINGS
Start Delay (SEC)
Cool-Down Period (SEC)
Low DC Bus Level (Vdc)
Hi DC Bus Level (Vdc)
Over-voltage Duration (SEC)
Automatic Test Interval (HR)
Service Required Service Interval (HR)
Service Due (HR)
Low Oil Pressure
High Engine Temperature
Over Speed
Over Crank
Low Fuel Level
CONTROL ALARMS
Control Fail
RAS Switch
ENCLOSURE ALARMS
Gas Hazard (LEL)
Water Intrusion
Pad Shear
Tamper
I/O CONTROLLER
Environmental Controller Status
Actstate
Mode
Temperature
Hysteresis
Timer Countdown
LAP Not Installed / Installed
Enclosure Fan Not Installed / Installed
Tamper Switch Status
Tamper Switch Polarity
Fig. 4-5, DSM3 Series Site Map
22
745-814-B8-001, Rev. A (08/2011)
4.0 Web Interface
4.3 Navigating the Web Page, continued
4.3.1 Web Interface Security Levels
Within the DSM3 Series transponder are two levels of function-specific security. General
operations are set at Level 1 and configuration-related functions are set at Level 2.
Default User ID and Passwords are shown in the figure below.
DSM3 Series Web Page Security
OID
Fucntion
1.3.6.1.4.1.4413.2.2.2.1.1.3.3.0
Level 1 Security ID
Alpha
1.3.6.1.4.1.4413.2.2.2.1.1.3.4.0
Level 1 Security Password
AlphaGet
1.3.6.1.4.1.4413.2.2.2.1.1.3.1.0
Level 2 Security ID
Alpha
1.3.6.1.4.1.4413.2.2.2.1.1.3.2.0
Level 2 Security Password
AlphaSet
Web Page
Function
Security Level
General
Value
sysName, sysContact, sysLocation, commonLogicalID
1
Power Supply Self Test
1
Generator Self Test
1
Reset Transponder
1
Advanced Communications
Configure Static IP Address
2
Configure Proprietary Trap Addresses
2
Advanced Power Supply
Power Supply Self Test
1
Generator Self Test
1
Reset Latched Alarms
1
Reset Log
1
LAP Installed/Not Installed
1
1
Advanced Generator
Modem Log [Event Log]
Advanced I/O
Fig. 4-6, DSM3 Series Transponder Security Levels
4.4
Verifying Communication Parameters
Also displayed on the “General” tab of the Web page are the common communication settings and values
of the DSM3 Series cable modem. Additional communication parameters may be viewed by navigating to
the "Communications" menu on the "Advanced Settings" tab.
General HMS
HMS
Alarms
Advanced
Settings
Alarms
Advanced
Settings
APPS
HISTORY
Print
Communications
Configuration
SysUpTime
Firmware Version
MAC Address
IP Address
CM Tx (dBmV)
CM Rx (dbMv)
SNR (RxMER)
2IP US
7 days 11H:13m:17s
4.4.6.0_02.00_NA
CM
CPE Transponder
00:90:EA:00:30:84
00:90:EA:00:30:85
192.168.1.124
192.168.1.120
42.0
42.0
+15
+30
+50
9.1
+55
9.1
-15
-10
0
+10
+15
45.4
System Name
Alpha
System Location
Bellingham
System Contact
John Doe
Common Logical ID
DSM3
SET
Fig. 4-7, Communication Parameters
745-814-B8-001, Rev. A (08/2011)
23
4.0 Web Interface
4.5
Verifying Power Supply and Battery Parameters
The “General” tab of the Web page also displays the common power supply and battery parameter
values. Important parameters such as current alarm status, inverter status and tamper status can be
quickly verified on this page for the particular DSM3 Series.
Power Supplies
Device 1
Model
ALPHA / XM2
Firmware
7.03.0
Major Alarm
OK
Minor Alarm
Inverter Status
Tamper
OK
OFF
Closed
Self Test
Start Test
Temperature 1 (°C)
Input Voltage (V)
Output Voltage (V)
LAP
41.60
15
124.80
89.00
1.00
Status
Actstate
Mode
Temperature
Hysteresis
Timer
Countdown
Contact Open
Not Installed
Closed
Not Installed
Heater
24
2
1
0
Batteries
String 1
Battery 1 (V)
13.90
Battery 2 (V)
13.95
Battery 3 (V)
14.00
String 2
13.95
14.00
13.90
Fig. 4-8, Power Supply and Battery Parameters
4.6
Remote Self-tests via the Web Page
Remote self tests on power supplies may be started and stopped via the DSM3 Series Web page. This
requires a Level 1 login. Refer to section 4.3.1, Web Interface Security Levels for user ID and password.
To launch a remote self-test, click on the “Start Test” button.
To stop a remote self-test before the predefined test duration, click on the "Stop Test" button.
Power Supplies
Device 1
Model
ALPHA / XM2
Firmware
7.03.0
Major Alarm
OK
Minor Alarm
Inverter Status
Tamper
Self Test
OK
OFF
Closed
Start Test
Temperature 1 (°C)
Input Voltage (V)
Output Voltage (V)
LAP
41.60
15
124.80
89.00
1.00
Status
Actstate
Mode
Temperature
Hysteresis
Timer
Countdown
Contact Open
Not Installed
Closed
Not Installed
Heater
24
2
1
0
Batteries
String 1
String 2
Battery 1 (V)
Battery 2 (V)
Battery 3 (V)
13.90
13.95
13.95
14.00
14.00
13.90
Fig. 4-9, Location of "Start" Button for Self-Test
24
745-814-B8-001, Rev. A (08/2011)
4.0 Web Interface
4.7
Viewing HMS Alarm Status via the Web Page
HMS alarms levels and currently reported states may be viewed by clicking on the "HMS Alarms" link on
the main Web page. An example is shown below.
®
HMS Alarm Configuration
General HMS
Alarms
Advanced
Settings
HMS
Alarms
Advanced
Settings
APPS
Print
Print
HISTORY
Property Tree
Parameter OID
PS Device 1
psOutputVoltage.1
psInputVoltage.1
psTotalStringVoltage.1
psPowerOut.1
psFrequencyOut.1
psStringFloat.1.1
psStringFloat.1.2
psOutputCurrent.1.1
psTemperature.1.1
TRANSPONDER
docsIfDownChannelPower.3
docsIfCmStatusTxPower.2
Current Alarm State
Alarm Enable
Major High1
Minor High1
Major Low1
Minor Low1
Alarm Dead Band
Nominal
Nominal
Nominal
Nominal
Nominal
Nominal
Nominal
Nominal
Nominal
Nominal
Nominal
Nominal
Nominal
Nominal
Nominal
Nominal
Nominal
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
9500
13000
4700
80000
0
700
700
0
0
700
4000
1500
1500
1500
1500
1500
1500
9050
12500
4500
60000
0
600
600
0
0
600
3500
1430
1430
1430
1430
1430
1430
7500
9500
3200
30000
0
50
50
0
0
400
0
1100
1100
1100
1100
1100
1100
8000
10000
3800
40000
0
100
100
0
0
500
500
1150
1150
1150
1150
1150
1150
100
100
50
99
0
10
10
0
0
10
80
18
18
18
18
18
18
Nominal
Nominal
0x00
0x00
150
550
100
500
-100
0
-150
0
15
15
Discrete Table
Parameter OID
PS Device 1
psMajorAlarm.1.1
psMajorAlarm.1.2
psMinorAlarm.1.1
psMinorAlarm.1.2
psTamper.1.1
psTamper.1.2
psInputVoltagePresense.1.1
psInputVoltagePresense.1.2
TRANSPONDER
tibControlMode.1.1
tibControlMode.1.2
tibControlMode.1.3
Alarm Value
Alarm Enable
Alarm State
1
2
3
4
5
1
2
1
2
1
2
1
2
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Nominal
Nominal
Nominal
Nominal
Nominal
Nominal
Nominal
Nominal
Nominal
Nominal
Nominal
Nominal
Nominal
1
2
1
2
3
Disabled
Disabled
Disabled
Disabled
Disabled
Nominal
Nominal
Nominal
Nominal
Nominal
1. Refer to Table 6-3 "Analog Alarms and Common Settings" for information regarding the scaling applied to the indicated values.
Fig. 4-10, HMS Alarm Configuration
745-814-B8-001, Rev. A (08/2011)
25
4.0 Web Interface
4.8
Viewing the Modem Event Log via the Web Page
The transponder's event log may be viewed using a Web browser. From the General ("home") page, click
on the Advanced Settings link, and select Modem Log from the drop down list. The Modem Log displays
the contents of the docsDevEventTable in an easy to read format. A total of 32 events are retained, with
the most recent at the bottom. The log may be reset by clicking on the RESET LOG button.
®
Docs Dev Event Table
General HMS
HMS
Alarms
Advanced
Settings
Alarms
Advanced
Settings
APPS
HISTORY
Print
Print
DocsDev Event Log
RESET LOG
docsDevEventFirstTime
docsDevEventLastTime
docsDevEvCounts
docsDevEvLevel
docsDevEvId
docsDevEvText
Thu Jan 01 21:15:07 2011
Thu Jan 01 21:15:07 2011
1
error
68000403
ToD request sent - No response received
Thu Jan 01 21:15:07 2011
Thu Jan 01 21:15:07 2011
1
warning
68000401
Thu Jan 01 21:15:09 2011
Thu Jan 01 21:15:09 2011
1
critical
68000300
DHCP WARNING - Non-critical field invalid in response
Thu Jan 01 21:15:22 2011
Thu Jan 01 21:15:22 2011
1
error
68000403
Thu Jan 01 21:15:22 2011
Thu Jan 01 21:15:22 2011
1
critical
68000400
Received response to Broadcast Maintenance request, but no Unicast
Maintenance opportuinties receives - T4 time out.
Thu Jan 01 21:15:23 2011
Thu Jan 01 21:15:23 2011
56
critical
68000100
SYNC Timing synchronization failure - Failed to acquire QAM/QPSK
symbol timing
Fig. 4-11, Modem Log Screen
4.9
Setting the I/O Controller via the Web Page
Settings for the LA-P-120SM / LA-P-240SM (e.g. to enable monitoring), and Tamper Switch Polarity
may be made by accessing the the IO - Environment page from the Advanced Settings drop down list.
To enable LA-P-120SM / LA-P-240SM monitoring, click on the Installed button. When prompted, refer
to Section 4.3.1 "Web Interface Security Levels" for the applicable user ID and password. The Tamper
Switch polarity may be changed in a similar fashion by clicking on the preferred button.
®
Advanced I/O Controller
General
HMS Alarms
Advanced Settings
APPS
HISTORY
Print
I/O Controller
Environmaental
Controller
LAP
Not Installed
Installed
Enclosure Fan
Not Installed
Installed
Tamper Switch Status
Status
Actstate
Mode
Temperature
Hysteresis
Timer
Countdown
Contact
Open
Closed
Heater
24
2
1
0
Not
Installed
Closed
Default
Reversed
Fig. 4-12, Advanced I/O Controller Status Screen
26
745-814-B8-001, Rev. A (08/2011)
4.0 Web Interface
4.10
Viewing and Configuring Power Supply settings via the Web Page
Connected power supply parameters may be viewed by clicking on the Advanced Settings heading, and
selecting Power Supplies from the drop down list. Power supply self-tests may be started by clicking
on the Start Test button. When prompted, refer to Section 4.3.1 "Web Interface Security Levels" for the
applicable User Name and Password.
®
Advanced Power Supply Settings
General
HMS
Alarms
Advanced
Settings
General HMS
Alarms
Advanced
Settings
APPS
History
Print
Print
ADVANCED POWER SUPPLY SETTINGS
Device 1
SELF TEST
Self test
Start Test
Test Countdown (DAY)
Test Duration (MIN)
Test Interval (DAY)
Test Inhibit
7
10
30
CHARGER
Accept (V/C)
Accept/Float
Batt Capacity (Ah)
Charger Current (A)
Charger Current Limit (A)
Float (V/C)
Temp Comp (mV)
2.40
2.27
41.00
2.00
10.00
2.27
5.00
INPUT
Input Freq (Hz)
Input Voltage (Vac)
Tap Switch
60.00
123.80
NO
INVERTER
Charger Enable
EOD Voltage (V/C)
Factory Test
Freq Range (Hz)
Inverter Enable
Set Defaults
Standby Events
Standby Time (MIN)
Total Run Time (DAY)
ON
1.75
OFF
3.00
ON
NO
127
5037
491
OUTPUT
Output 1 Curr (A)
Output 2 Curr (A)
Output 3 Curr (A)
Output 4 Curr (A)
Output VA (VA)
Output Voltage (Vac)
Output Watts (W)
Over Curr Tol (SEC)
Peak Curr 1 (A)
Peak Curr 2 (A)
Peak Curr 3 (A)
Peak Curr 4 (A)
Percent Load (%)
PIM Option
N+1 In Use
N+1 Valid
Retry Delay (SEC)
Retry Limit
1.20
0.00
0.00
0.00
110.00
89.00
90.00
3000
1.20
0.00
0.00
0.00
7.00
NO
NO
No
60
20
Fig. 4-13, Advanced Power Supply Settings Screen
745-814-B8-001, Rev. A (08/2011)
27
5.0 Upgrading Firmware
5.1
Upgrading DSM3 Series Modem Firmware
The firmware is upgraded using standard DOCSIS methods as defined in RFC4639.
There are two ways to upgrade the modem’s firmware: by directly setting the appropriate MIB parameters
in the docsDevSoftware branch, or by including the appropriate SNMP parameters and values in the
modem’s DOCSIS Configuration File, stored on the TFTP root directory.
Both methods are explained below.
5.1.1 Identifying the Modem and Obtaining Firmware Files
The cable modem firmware in the DSM3 Series requires its own firmware and manufacturer's
Code Verification Certificate (CVC file).
Contact Alpha Technologies to obtain the latest firmware and manufacturer's CVC files.
5.1.2 Modem Firmware Upgrade SNMP Parameters
Modem Firmware Upgrade SNMP Parameters
Parameter
Type
Value
docsDevSoftware
OID: 1.3.6.1.2.1.69.1.3
Object Heading
None
docsDevSwServer
OID: 1.3.6.1.2.1.69.1.3.1.0
IP Address
The IP address of the TFTP server from which the firmware will be
downloaded"
docDevSwFilename
OID: 1.3.6.1.2.1.69.1.3.2.0
Octet String
Set to the filename of the firmware file. Example: [“firmwareImage.bin”]
docsDevSwAdminStatus
OID: 1.3.6.1.2.1.69.1.3.3.0
Integer
1 = Initiate upgrade (manual method)
2 = Upgrade on next reboot (Config File Method)
3 = Ignore update
docsDevSwOperStatus
OID: 1.3.6.1.2.1.69.1.3.4.0
Integer,
Read Only
1 = TFTP download is in progress
2 = Last upgrade was performed at reboot
3 = Last upgrade was initiated by setting docsDevSwAdminStatus to “1”
4 = Firmware upgrade failed
5 = Other
docsDevSwCurrentVers
OID: 1.3.6.1.2.1.69.1.3.5.0
Octet String,
Read Only
The current version of firmware installed in the modem
docsDevSwServerAddressType
1.3.6.1.2.1.69.1.3.6.0
Integer,
Read Only
The type of address (IPv4, IPv6) of server used or upgrades
OID: 1.3.6.1.2.1.69.1.3.7.0
IP Address
The IP address of the server from which the firmware will be
downloaded. A set of this object to an IPv4 address will result in also setting
the value of docsDevSwServer to that address. If this object is set to an
IPv6 address, docsDevSwServer is set to 0.0.0.0. If docsDevSwServer is
set, this object is also set to that value.
docsDevSwServerTransportProtocol
1.3.6.1.2.1.69.1.3.8.0
Integer,
Read Only
The Transport protocol to be used for software upgrades:
1 = tftp
2 = http
Table 5-1, Modem Firmware Upgrade SNMP Parameters
28
745-814-B8-001, Rev. A (08/2011)
5.0 Upgrading Firmware
5.1.3 Upgrading Manually by Setting SNMP Parameters
1. Acquire the firmware and CVC files for your DSM3 Series from Alpha Technologies.
2. Import the CVC into the modem’s DOCSIS Configuration File (to create a Configuration File,
see Section 3.2).
3. Set the following MIB parameters using an SNMP MIB browser. For additional information
regarding the SNMP MIB parameters, refer to the table in Section 5.1.2., "Modem Firmware
Upgrade SNMP Parameters".
Parameter
Value
docsDevSwServer
IP Address of TFTP server
docsDevSwFilename
Firmware filename
1
The firmware upgrade will begin immediately. Monitor the upgrade status with the
docsDevSwOperStatus MIB parameter, and verify the firmware version with the
docsDevSwCurrentVers MIB parameter (refer to Table 5-1, "Modem Firmware Upgrade SNMP
Parameters"). Once the firmware has been upgraded, the modem will automatically run the new
version.
5.1.4 Upgrading via the DOCSIS Configuration File
DSM3 Series firmware can be automatically upgraded using the DOCSIS Configuration File
by adding the following docsDevSoftware SNMP parameters and the manufacturer’s Code
Verification Certificate (CVC).
Parameter
Value
docsDevSwServer
IP Address of TFTP server
docsDevSwFilename
Firmware filename
2
Manufacturer CVC
The CVC file for the DSM3 Series
The firmware will be upgraded on the next reboot. Monitor the upgrade status with
the docsDevSwOperStatus MIB parameter, and verify the firmware version with the
docsDevSwCurrentVers MIB parameter (refer to Table 5-1, "Modem Firmware Upgrade SNMP
Parameters"). Once the firmware has been upgraded, the modem will automatically run the new
version.
745-814-B8-001, Rev. A (08/2011)
29
6.0 Data Management
6.1
SCTE-HMS MIBs
The DSM3 Series remotely reports power supply data and alarms using the Simple Network Management
Protocol (SNMP) over the DOCSIS (Data Over Cable Service Interface Specification) communications standard.
The DSM3 Series typically reports into a centralized Network Management System (NMS) through a standard
collection of data access points referred to as the SCTE-HMS Management Information Bases (MIBs). The NMS
polls the DSM3 Series for power supply data with the option of having the DSM3 Series send SNMP traps in the
event that an alarm condition occurs. In addition to the SCTE-HMS MIBs, the DSM3 Series also supports the
Alpha proprietary SNMP MIBs, which allows direct access to the power supply as well as the ability to change
transponder settings.
The following MIB (Management Information Base) files are required for the NMS or SNMP Manager to
collect data from the transponders. These files can be found on the Society of Cable Telecommunications
Engineers (SCTE) Web site www.scte.org. There are dependencies between MIB files so they should be
compiled in the order listed below:
Reference Number
ANSI/SCTE 36 2002R2007
(formerly HMS 028)
ANSI/SCTE 37 2010
Description
SCTE-ROOT Management Information Base (MIB) Definitions
Hybrid Fiber/Coax Outside Plant Status Monitoring
(formerly HMS 072),
SCTE-HMS-ROOTS Management Information Base (MIB) Definition
ANSI/SCTE 38-1 2009
(formerly HMS 026)
SCTE-HMS-PROPERTY-MIB Management Information Base (MIB) Definition
ANSI/SCTE 38-2 2005
(formerly HMS 023)
SCTE-HMS-ALARMS-MIB Management Information Base (MIB) Definition
ANSI/SCTE 38-3 2008
(formerly HMS 024)
SCTE-HMS-COMMON-MIB Management Information Base (MIB) Definition
ANSI/SCTE 38-4 2006
(formerly HMS 027)
SCTE-HMS-PS-MIB Management Information Base (MIB) Definition
ANSI/SCTE 38-6 2006
(formerly HMS 033)
SCTE-HMS-GEN-MIB Management Information Base (MIB) Definition
ANSI/SCTE 38-7 2008
(formerly HMS 050)
SCTE-HMS-Transponder-Interface-Bus (TIB)-MIB Management Information Base (MIB) Definition
Table 6-1, SCTE-HMS MIB Files
30
745-814-B8-001, Rev. A (08/2011)
6.0 Data Management
6.2
SCTE-HMS MIB Alarms
6.2.1 SCTE-HMS Configurable Alarms
The HMS discrete and analog alarms provide the capability to monitor and alarm various
power supply and environmental conditions and measurements. The alarms in the SCTEHMS propertyTable and the discretePropertyTable can be defined and set to provide a custom
monitoring system.
The following section provides an example and detailed information on how to set values, enable
or disable alarms in the MIB tables. For ease of reference they are in this sequence:
• An example of how set a temperature alarm
• A table to help convert the desired reported alarm states to hexadecimal for setting the MIB
• Commonly monitored parameters and recommended values
Example:
The alarms for psTemperature below are set so that the normal temperature range is from
30°C to 45°C. If the temperature rises above 45°C, a casHI alarm will be sent to the alarmTable.
Anything over 50°C is considered a critical condition and will generate a casHIHI alarm. If the
temperature falls below the normal level of 30 degrees and casLO will be generated and if it
continues to drop below 0, a casLOLO will be generated. The temperature must rise above the
LOLO limit plus the deadband value of 3°C before the casLOLO alarm will change to a casLO.
The alarmEnable field is set to 0F Hex to monitor and alarm for all conditions.
0F (hex)
psTemperature
Binary to Hex Conversions for Alarm Settings
HiHi
Hi
Lo
LoLo
Bit 7
Bit 6
Unused
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Hex
Enabled Alarms
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
00
01
No Alarms
LoLo
0
0
0
0
0
0
1
0
02
Lo
0
0
0
0
0
0
1
1
03
Lo, LoLo
0
0
0
0
0
1
0
0
04
Hi
0
0
0
0
0
1
0
1
05
Hi, LoLo
0
0
0
0
0
1
1
0
06
Hi, Lo
0
0
0
0
0
1
1
1
07
Hi, Lo, LoLo
0
0
0
0
1
0
0
0
08
HiHi
0
0
0
0
1
0
0
1
09
HiHi, LoLo
0
0
0
0
1
0
1
0
0A
HiHi, Lo
0
0
0
0
1
0
1
1
0B
HiHi, Lo, LoLo
0
0
0
0
1
1
0
0
0C
HiHi, Hi
0
0
0
0
1
1
0
1
0D
HiHi, Hi, LoLo
0
0
0
0
1
1
1
0
0E
HiHi, Hi, Lo
0
0
0
0
1
1
1
1
0F
HiHi, Hi, Lo, LoLo
Table 6-2, Binary to Hex Conversions for Alarm Settings
745-814-B8-001, Rev. A (08/2011)
31
6.0 Data Management
6.2.1
SCTE-HMS Configurable Alarms, continued
The following table displays the various analog alarms with common settings for the DSM3 Series
Transponder.
Analog Alarms and Common Settings
Analog Alarms
36V
psTotalStringVoltage
48V
psBatteryVoltage
120V
psInputVoltage
220V
48V
60V
psOutputVoltage
Description
Scaled representation of the full
battery string in 1/100 Volts units
Alarm
LOLO
Enable
LO
HI
HIHI Deadband
0x0F
3300
3500
4520
4570
50
0x0F
4400
4785
6030
6100
50
Battery Voltage of 12V battery,
scaled 1/100 V
0x0F
1050
1150
1530
1550
20
Scaled representation of the input
line voltage in 1/100 Volts units
0x0F
Varies by site. The XM2 will switch to standby at
nominal +15% -20%
Scaled representation of the
power supply output voltage in
1/100 Volts units.
90V
0x0F
0x0F
4300
4550
5050
5300
200
0x0F
5650
6000
6600
7000
200
0x0F
7800
8200
9150
9300
200
psPowerOut
Representation of power supply
output power in 1W units.
0x00
It is recommended that psOutputCurrent be used
for output alarms.
psStringChargeCurrent
Battery string charge current,
scaled in 1/100 Amp units.
0x0C
Disable
Disable
1200
1250
20
psStringFloat
Battery string float charge current,
scaled in 1/100 Amp units.
0x0C
Disable
Disable
1200
1250
20
15A
0x0C
Disable
Disable
1650
1720
20
18A
0x0C
Disable
Disable
1980
2060
20
22A
0x0C
Disable
Disable
2420
2530
40
24A
0x0C
Disable
Disable
2640
2750
40
-40 to +80 degrees C
0x0F
Varies by site
generator's ignition battery in
1/100 Volts
0x0F
1150
1200
1500
1550
20
GenVBatIgnition
genEnclosureTemperature
Temperature inside generator's
enclosure in degrees C
0x09
-40
0
0
55
5
psTemperature
Alarms for Optional Generator
Table 6-3, Recommended Settings for DSM3 Series Analog Alarms
The following table displays analog alarms with common settings for the DPM Transponder that
differ from the DSM3 Series models.
Analog Alarms and Common Settings, DPM
Analog Alarms
Description
120V
psInputVoltage
220V
60V
psOutputVoltage
63V
3.5A*
psOutputCurrent
5.0A*
Scaled representation of the input
line voltage in 1/100 Volts units
power supply output voltage in
1/100 Volts units.
Scaled representation of power
supply RMS current in 1/100 Amp
units.
Alarm
LOLO
Enable
0x0F
0x0F
LO
HI
HIHI Deadband
Varies by site. The XM2-300HP will switch to
standby at nominal +10% -15%
0x0F
5150
5350
6150
6350
200
0x0F
5650
6000
6600
7000
200
0x0C
Disable
Disable
380
390
0x0C
Disable
Disable
550*
575*
Table 6-4, Recommended Settings for DPM Analog Alarms
32
745-814-B8-001, Rev. A (08/2011)
6.0 Data Management
6.2.1
SCTE-HMS Configurable Alarms, continued
Discrete Alarms
Description
Setting
psInverterStatus (1)
Inverter OFF
Disable
Inverter running due to loss of AC Line voltage
discreteMinor
Self-Test initiated locally
Disable
Self-Test initiated remotely
Disable
Last Self-Test failed
discreteMajor
psMajorAlarm (1)
No Alarm
Disable
psMajorAlarm (2)
Alarm
discreteMajor
psMinorAlarm (1)
No Alarm
Disable
psMinorAlarm (2)
Alarm
discreteMinor
psTamper (1)
Closed
Disable
psTamper (2)
Open
discreteMajor
psInputVoltagePresence (1)
AC Line Voltage Lost
Disable
psInputVoltagePresence (2)
AC Line Voltage Present
Disable
tibControlMode (1)
Device will respond to commands
Disable
tibControlMode (2)
Device is under local control
Disable
tibControlMode (3)
Remote device is not responding
discreteMajor
Discrete Alarms for Optional Generator
genGeneratorStatus (1)
Generator Off
Disable
Generator Running (Test)
discreteMinor
Generator Running
discreteMajor
Generator Fail
discreteMajor
genGasHazard (1)
No Alarm
Disable
genGasHazard (2)
The concentration of hydrocarbon fuel in the generator enclosure has exceeded safe
limits. Generator operation is suspended. The alarm is cleared when the sensor reports
safe conditions, and the alarm is reset via the resetLatchedAlarms(3) command found in
the genEquipmentControl MIB point..
discreteMajor
genWaterIntrusion (1)
No Alarm
Disable
genWaterIntrusion (2)
Water level within the generator or fuel enclosure has exceeded safe limits for generator
operation. Generator operation is suspended while this alarm is active. The alarm resets
when the water returns to a safe level.
discreteMajor
genPadShear (1)
No Alarm
Disable
genPadShear (2)
Indicates that the generator or fuel enclosure has shifted from its mounting position.
Generator operation is suspended. The alarm resets when the unit is returned to its
original position.
discreteMajor
genEnclosureDoor (1)
No Alarm
Disable
genEnclosureDoor (2)
Generator and/or auxiliary fuel enclosure door is open
discreteMajor
genCharger (1)
No Alarm
Disable
genCharger (2)
Ignition battery charger is not operating correctly
discreteMajor
genFuel (1)
No Alarm
Disable
genFuel (2)
Indicates the engine's fuel supply is insufficient for extended operation. Alarm resets
when fuel is replenished.
discreteMajor
genOil (1)
No Alarm
Disable
genOil (2)
Indicates the engine's oil is inadequate for safe operation. Alarm resets when the
condition returns to normal.
discreteMajor
genMinorAlarm (1)
No Alarm
Disable
genMinorAlarm (2)
The generator is indicating a minor alarm. The generator requires attention, but does not
require an immediate visit to the site.
discreteMinor
genMajorAlarm (1)
No Alarm
Disable
genMajorAlarm (2)
The generator is indicating a major alarm. The generator requires immediate attention.
discreteMajor
Table 6-5, Recommended Settings for Discrete Alarms
745-814-B8-001, Rev. A (08/2011)
33
6.0 Data Management
6.2.2 SNMP Traps
Use of SNMP Traps allow the network manager to set conditions (alarms) under which the device
(or devices) autonomously report to the headend the existence of the pre-configured event. The
type of event determines the level of action to be taken.
1. Verify the IP address of the trap destination server(s) has been configured.
If the trap destination server requires configuration, refer to Section 3.2.2, "Setting SNMP
Trap Destination Addresses" for instructions.
2.
Alarms must be configured. SNMP alarm traps sent by the transponder are formatted
according to the SCTE-HMS-ALARM-MIB specification with the following
information included:
SNMP Trap community string:
commonTrapCommunityString, OID 1.3.6.1.4.1.5591.1.3.1.11.0
Default value is "public"
Example Alarm Trap
The example below is a psTamper alarm trap indicating a discreteMinor alarm: Tamper is open.
Data from the raw trap will appear as shown below. Refer to Table 6-6 "SNMP Alarm Trap
Varbinds and Explanations" for definitions of the varbinds.
Frame 441 (230 bytes ib wire, 230 bytes captured)
Ethernet II, Src: 192.168.1.77 (00:90:EA:A0:01:4E), Dst: 3com_0d:1d:d4 (00:10:5a:0dL1d:d4)
Internet Protocol, Src Port: 62481 (62481), Dst Port: snmptrap (162)
Simple Network Management Protocol
Version: 1 (0)
Community: PUBLIC
PDU type: TRAP-V1 (4)
Enterprise: 1.3.6.1.4.1.5591.1 (SNMPv2-SMI::enterprises.5591.1)
Agent address: 0.0.0.0 (0.0.0.0)
Trap type: ENTERPRISE SPECIFIC (6)
Specific trap type: 1
Timestamp: 2358751
Object identifier 1: 1.3.6.1.4.1.5591.1.3.2.7.0 (SNMPv2-SMI::enterprises.5591.1.3.2.7.0)
Value: Hex-STRING: 00 90 EA A0 0B 82
Object identifier 2: 1.3.6.1.4.1.5591.1.3.1.1.0 (SNMPv2-SMI::enterprises.5591.1.3.2.1.0)
Value STRING: “123 Example Ave.”
Object identifier 3: 1.3.6.1.4.1.5591.1.2.3.1.2.1 (SNMPv2-SMI::enterprises.5591.1.2.3.1.2.1)
Value: Hex-STRING: 00 00 00 76 07 10 06 0D 2B 06 01 04 01 AB 57 01 04 02 01 1B 01 02 01 02
Object identifier 4: 1.3.6.1.4.1.5591.1.4.2.1.27.1 (SNMPv2-SMI::enterprises.5591.1.3.2.1.0)
Value: INTEGER: 2
Object identifier 5: 1.3.6.1.4.1.5591.1.1.2.1.2 (SNMPv2-SMI::enterprises.5591.1..1.2.1.2)
Value: INTEGER: 7
Fig. 6-1, Sample Raw SNMP Alarm Trap
When viewed through a third-party trap receiver, the translated varbinds and data values will be
displayed in a format similar to the sample below:
Bindings (5)
Binding #1: commonPhysAddress.0 *** (octets) 00:90.EA.A0.01.4E (hex)
Binding #2: commonLogicalID.0 *** (octets) (123 Example Ave.)
Binding #3: alarmLogInformation.1 *** (octets) 00.00.00.76.07.10.06.0D.2B.06.01.04.01.AB.57.01.04.02.01.1B.01.02.01.02 (hex)
Binding #4: psTamper.1 *** (int32) open (2)
Binding #5: currentAlarmAlarmState *** (int32) caasDiscreteMinor(7)
Fig. 6-2, Sample Translated SNMP Alarm Trap
34
745-814-B8-001, Rev. A (08/2011)
6.0 Data Management
6.2.2
SNMP Alarm Traps, continued
Varbind
Explanation
Binding #1
commonPhysAddress
OID: 1.3.6.1.4.1.5591.1.3.2.7.0
MAC Address of the transponder
Binding #2
commonLogicalID
OID: 1.3.6.1.4.1.5591.1.3.1.1.0
Optional user-configurable parameter that is often used to provide a unique logical name, or even
the physical address of where the transponder is installed.
Binding #3
alarmLogInformation
OID: 1.3.6.1.4.1.5591.1.2.3.1.2.1
This varbind was designed by the SCTE-HMS committee with the intention of being used by
sophisticated trap interpreters. The information is “coded” within the octet strings:
Octet 1-4: POSIX Time of alarm occurrence (most significant byte first)
Octet 5: Alarm Type (See description below)
Octet 6: Contents of commonNeStatus immediately after alarm occurred
Octet 7-m: Alarm Object Identifier (BER encoded)
Octet n-z: Alarm value (BER encoded)
Most trap interpreters cannot decode this message, which is why varbinds 4 and 5 were added that
provide the same information in a more useable format.
Binding #4
Alarmed Parameter OID/Value
OID:
1.3.6.1.4.1.5591.1.4.2.1.27.1
This field provides the varbind of the parameter that is alarming along with the value of that
parameter. This is the same information encoded in varbind #3 Octets 7 through Z.
In the example above the value would be:
OID: 1.3.6.1.4.1.5591.1.4.2.1.27.1.0 (psTamper)
Value: 2 (Open)
Binding #5
Alarm Location/Type
OID: 1.3.6.1.4.1.5591.1.1.2.1.2
This is the information from varbind #3 Octet 5 above. The alarm location will always be the
SCTE-HMS currentAlarmAlarmState and the type will be determined based on how the alarm was
configured in the SCTE-HMS PropertyIdent MIB tables.
OID 1.3.6.1.4.1.5591.1.1.2.1.2.0 (currentAlarmAlarmState)
Type: 1-7 based on SCTE definitions:
1 NOMINAL
2 HIHI
3 HI
4 LO
5 LOLO
6 Discrete Major
7 Discrete Minor
The Type will be determined by how the alarm is configured in the SCTE-HMS PropertyIdent MIB,
whether it is a Discrete or Analog alarm and the level of alarm defined for that state.
Table 6-6, SNMP Alarm Trap Varbinds and Explanations
Trap on Normal
The DSM3 Series has the capability of sending a “return to normal” trap once an alarmed condition
returns to a normal state. This feature is enabled by default, but can be disabled by setting the
"TRAP ON NORMAL" parameter in the the MIB point atiMgmtSnmpTrapOnNormal to a value of "2".
The contents of this trap message will be identical to the SNMP Alarm traps, but the value of the
Alarm "Type" defined in the 5th varbind will be "1" (NOMINAL).
SCTE-HMS Warm-Start Trap
In addition to the SNMP alarm traps, the DSM3 Series will also send an SCTE-HMS warm-start trap
when it is initialized. Some SNMP monitoring software requires this trap for auto-identification of the
transponder. The format of this trap will be similar to the alarm trap, but the only information sent
will be:
commonTrapCommunityString, OID 1.3.6.1.4.1.5591.1.3.1.11.0
commonPhyAddress, OID, 1.3.6.1.4.1.5591.1.3.2.7
commonLogicalID, OID 1.3.6.1.4.1.5591.1.3.1.1.0
SCTE-HMS Cold-Start Trap
An SNMP-HMS cold-start trap will be generated by the DSM3 Series anytime it initializes with a
new firmware version. In addition, a cold start trap is sent whenever the DSM3 configuration has
changed. If any parameter in the HMS PROPERTY table has changed since the last reset, a
cold-start trap will be sent upon the next reset.
745-814-B8-001, Rev. A (08/2011)
35
6.0 Data Management
6.2.3 General Power Supply Alarms
General power supply alarms are passed directly from the power supply to the transponder
without specific definition and are classified in the HMS MIB table as psMinorAlarm and
psMajorAlarm. There are a number of problems that can generate these alarms and the exact
nature of the situation is not specified. Minor and Major alarms are defined by the SCTE
standards committee as follows:
psMajor
“Service has been dropped or a service interruption is imminent. Indicates that an immediate
truck roll is appropriate.” Several psMajor alarms are latching, meaning that the alarm won’t
clear until the problem is fixed and after a successful completion of a self-test. A self-test is the
preferred method of verifying the resolution of the alarm condition as cycling the power has the
potential of masking the problem and not indicating the actual state of the system.
psMinor
“A non-service affecting condition has occurred and should be monitored.”
The following table lists the psMajor and psMinor alarm definitions for the XM2 power supply.
NOTE:
The cause of a psMajor or psMinor alarm can be determined by checking the Discretes table in the Alpha MIB
or by viewing the Web page. The cause will have the value of “ALARM.”
XM2 Major and Minor Alarms
psMinor
Problem
Definition
Line Loss from Inverter Status
Loss of AC line as determined by power supply inverter.
Battery Temperature Probe
Indicates a temperature probe has failed or is not connected.
N+1 Error
N+1 circuit isn’t configured properly. Possibly detecting input voltage on a redundant system
or other issue.
psMajor
Problem
Definition
Output Failure (non-latching)
AC output failure, an open or short detected by power supply.
General Failure (latching)
Indicates a latched failure of an automated, local or remote inverter test, or some other
major malfunction within the power supply.
Test Fail (latching)
Battery voltage drops below 1.85V/cell or inverter fail during self test.
Battery Fail (non-latching)
Battery voltage drops below 1.75V/cell while in standby mode, battery exceeds 2.5V/cell, or
batteries not detected.
Line Isolation (latching)
Line isolation circuitry has failed.
Output Overload (non-latching)
Indicates the power supply is overloaded. Power supply will shut down and attempt to restart
periodically.
Charger Failure (non-latching)
Charger has failed or was shut down due to a problem such as battery over-temp.
Inverter Fail (latching)
The power supply has detected a failure in inverter operation.
Configuration Failure
The power supply has detected that it is improperly configured.
Overtemp
Inverter heat sink over-temperature.
N+1 Active
A power supply has failed and the N+1 system has been activated to provide backup power.
Fuse Fail
Fuse failure on tap switch option board.
Table 6-7, XM2 Major and Minor Alarms
36
745-814-B8-001, Rev. A (08/2011)
6.0 Data Management
6.3
The Alpha MIBs
Accompanying the release of the DSM3 Series are 22 new MIB files. These are backward-compatible
with the existing Alpha Technologies DSM series transponders. These MIBs are available by contacting
Alpha Technical Support or from the Alpha website. A complete listing is shown below:
ATI-BB-SYS-APPS-MIB.my
ATI-BB-SYS-LOGS-MIB.my
ATI-BB-SYS-VIEW-MIB.my
ATI-MANAGEMENT-MIB.my
ATI-MGMT-SNMP-MIB.my
ATI-MGMT-SYS-ACCESS-MIB.my
ATI-MGMT-SYS-DOWNLOAD-MIB.my
ATI-MGMT-SYS-GENRL-CTRL-MIB.my
ATI-MGMT-SYS-GENRL-INFO-MIB.my
ATI-MGMT-SYS-LAP-MIB.my
ATI-MGMT-SYS-MIB.my
ATI-MGMT-SYS-NV-DEFAULTS.my
ATI-MGMT-SYS-PHONEHOME-MIB.my
ATI-MGMT-SYS-SERVERS-MIB.my
ATI-MGMT-SYS-TEMP-MGR-MIB.my
ATI-MPSPS-MIB.my
ATI-PKT-CABLE-UPS-MIB.my
ATI-PRODUCT-PLATFORMS-MIB.my
ATI-ROOT-MIB.my
ATI-TABLES-MGMT-MIB.my
ATI-TABLES-MIB.my
ATL-ROOT-MIB.my
MIB browsers such as MG-Soft (www.mg-soft.com) require these MIBs to be compiled into the browser
for the branches and parameters to be ordered and displayed properly. Refer to your MIB browser’s
documentation for instructions on compiling MIB files.
The following MIB files may be required (see http://www.simpleWeb.org) to be compiled into the MIB
browser prior to the Alpha MIB files:
RFC-1212
RFC-1215
RFC1155-SMI
SNMPv2-MIB
SNMPv2-TC
Additionally, there are four MIBs from Broadcom that are necessary to support the new features of the
DSM3 Series. They are:
BRCM-CABLEDATA-MGMT.my
BRCM-CABLEDATA-SMI.my
BRCM-HTTP-MGMT.my
BRCM-TELNET-MGMT.my
745-814-B8-001, Rev. A (08/2011)
37
6.0 Data Management
6.3
The Alpha MIBs, continued
The Alpha MIB is defined within the enterprises branch of the MIB tree starting at 1.3.6.1.4.1.926 and is
organized as shown in the overview below:
MIB Tree
ccit
iso (1)
org (1.3)
dod (1.3.6)
internet (1.3.6.1)
directory (1.3.6.1.1)
mgmt (1.3.6.1.2)
experimental (1.3.6.1.3)
private (1.3.6.1.4)
enterprises (1.3.6.1.4.1)
atl(1.3.6.1.4.1.926)
alphaTechInc(1.3.6.1.4.1.926.1)
atiLegacyReserved01(1.3.6.1.4.1.926.1.1)
atiTables (1.3.6.1.4.1.926.1.2)
atiManagement (1.3.6.1.4.1.926.1.3)
atiMgntSnmp (1.3.6.1.4.1.926.1.3.1)
atimgntSnmpTrapTable(1.3.6.1.4.1.926.1.3.1.1)
atimgntSnmpAccessTable(1.3.6.1.4.1.926.1.3.1.2)
atimgntSnmpAccess(1.3.6.1.4.1.926.1.3.1.3)
atimgntSnmpCommunities(1.3.6.1.4.1.926.1.3.1.4)
atimgntSnmpControls(1.3.6.1.4.1.926.1.3.1.5)
atiMgntSys (1.3.6.1.4.1.926.1.3.2)
atiMgntSysDownload (1.3.6.1.4.1.926.1.3.2.1)
atiMgntSysAccess (1.3.6.1.4.1.926.1.3.2.2)
atiMgntSysServers (1.3.6.1.4.1.926.1.3.2.3)
atiMgntSysTempMgr (1.3.6.1.4.1.926.1.3.2.4)
atiMgntSysPhoneHome (1.3.6.1.4.1.926.1.3.2.5)
atiMgntSysGnrlControls (1.3.6.1.4.1.926.1.3.2.6)
atiMgntSysGnrlInfo (1.3.6.1.4.1.926.1.3.2.7)
atiMgntSysLAP (1.3.6.1.4.1.926.1.3.2.8)
atiMgntSysNvDefaults (1.3.6.1.4.1.926.1.3.2.9)
atiProductPlatforms (1.3.6.1.4.1.926.1.4)
atiBroadbandUPS (1.3.6.1.4.1.926.1.4.1)
atiBBSysView (1.3.6.1.4.1.926.1.4.1.1)
Table 6-8, Alpha MIB Hierarchy
38
745-814-B8-001, Rev. A (08/2011)
6.0 Data Management
6.3
The Alpha MIBs, continued
6.3.1 The Alpha MIB Structure
Measurements and settings for the power supply, generator, batteries and DSM are accessed
using Simple Network Management Protocol (SNMP) through the Alpha Management Information
Base (MIB) files.
The Alpha MIB is defined within the enterprise branch of the MIB tree starting at 1.3.6.1.4.1.926
and is organized into the following branches:
Alpha CIB Tables – atiTables (1.3.6.1.4.1.926.1.2.1)
Power supply, generator, battery and DSM data and settings are located in the CIB Tables branch (atiCibTables). The tables are sorted into
the following categories:
1.
Discretes - XM2 major alarms & installed XM2 options.
2.
Analogs - Voltages, currents, frequencies, temperatures.
3.
Counters - Batteries per string, number of strings, XM2 self-test schedule, device address, total run time and configuration settings.
4.
Version - Device version information.
Alpha Management – atiManagement (1.3.6.1.4.1.926.1.3)
Advanced DSM settings are located in the Alpha management branch (atiManagement) and the settings are split between SNMP and
system-related settings.
1.
SNMP Management – atiMgntSnmp (1.3.6.1.4.1.926.1.3.1)
1.1
SNMP Trap Table - Table of SNMP trap addresses.
1.2
SNMP Access Table – Table of SNMP access addresses.
1.3
SNMP Access – Device accessibility via SNMPv1 & SNMPv2.
1.4
CPE Mode – Enable/disable dual IP and static IP settings.
1.5
Community Strings – Get, set and trap community strings.
1.6
SNMP Trap controls – Trap on normal, send count, SNMP timeout.
2.
System Management – atiMgmtSys (1.3.6.1.4.1.926.1.3.2)
SNMP Trap tables, SNMP access, Community Strings and SNMP Trap controls.
Download, Web server, SNTP server IP addresses, enclosure environmental controller, general controls (tamper polarity) and LA-P
status.
2.1
Download – DSM Proprietary Configuration File settings.
2.2
System Access – Enable/disable Web Page & Text Page - applies to DSM1 & DSM2 only.
2.3
HTTP Access - Enable/disable Web page – DSM3.
2.4
System Servers – Simple Network Time Protocol server (SNTP) IP address.
2.5
Temperature Manager – Battery heater mat or cooler settings.
2.6
Phone Home – IP address and timer settings.
2.7
General Controls – Tamper switch polarity and internal bus data size.
2.8
General Info – Base configuration of the device. i.e. DSM3, DSM3 Series, DPM.
2.9
LA-P Surge Suppressor – Enable/disable LA-P monitoring and current state of LA-P device.
2.10
Non-volatile Memory Defaults – Factory and custom defaults.
Alpha Product Platforms – atiProductPlatforms (1.3.6.1.4.1.926.1.4)
System power supply parameters are located the Alpha Product Platforms branch (atiProductPlatforms).
1.
Broadband UPS
1.1
Self Test – Start/stop and prevention and System Control Manager.
1.2
Alarms – Status of major and minor alarm, self test, temperature probe and input power.
1.3
Scalars – Power supply input voltage, frequency and current. Battery voltage and temperature. Charger settings.
1.4
Counters – Self test and inverter counters.
System View – Self Test, alarms, scalars, and counters reported by the host device.
Refer to Section 10 for further details regarding the Alpha MIBs.
745-814-B8-001, Rev. A (08/2011)
39
7.0 Installation
7.1
Verifying Power Supply Device Address
Before installing the hardware, provision the DHCP server with the cable modem’s RF MAC Address. This
allows the installation to be verified while the technician is on-site, eliminating the need for a second visit if
there are problems with the installation.
WARNING!
To reduce the risk of electric shock, completely remove the inverter module from the power
supply prior to installation. For field installation, use a service power supply to avoid losing
power to the load.
CAUTION!
The DSM3 Series is static sensitive. An ESD wrist strap should be worn when installing the
transponder.
Before removing the Inverter Module (IM), verify the power supply device address is correct.
The power supply device address must not be set to zero and no two power supplies monitored by a
single DSM3 Series can have the same address. Power supplies must have 1, 2, 3, 4 or 5 as an address.
To verify the power supply’s address do the following:
Smart Display Screen
1. Press the Enter key on the inverter module twice to access the SETUP Menu.
2. Press the Down key until DEVICE ADDRESS is displayed.
3. If the address is correct (in the range of 1 to 5), skip to Step 8.
4. To change the address, press the Enter key to enter the Edit mode.
5. Press the Up or Down keys until the desired address (1, 2, 3, 4 or 5) is displayed. Remember, each
power supply monitored by a single transponder must have a unique address; this may require
accessing the menu systems of the additional power supplies and adjusting as applicable.
6. Press the Enter key to load the new address.
7. Press the Enter key again to accept the new data.
8. Press ESC three times to return to the OPERATION NORMAL screen.
40
745-814-B8-001, Rev. A (08/2011)
7.0 Installation
7.2
Installation / Replacement Procedure in XM2 Power Supplies
If the CableUPS has been shipped without a DSM3 Series module, or the existing module requires
removal and replacement, do so via the the following procedure:
1. Switch OFF the power supply’s battery breaker.
NOTE:
With the battery breaker in the OFF position, the power supply will not go into inverter mode.
2. Unplug all inverter module connections (e.g. battery cable, remote temperature sensor).
3. Loosen the inverter module thumbscrews and slide the inverter module out just enough to disconnect
the ribbon cable. Disconnect the ribbon cable.
4. Slide the Inverter Module out of the power supply.
5. If the inverter module is equipped with a communication module, remove it by loosening the two
Phillips captive screws.
Disconnect
Captive Screws
Fig. 7-1, Removing the Inverter Module from the Power Supply
745-814-B8-001, Rev. A (08/2011)
41
7.0 Installation
7.2
Module Installation Procedure in XM2 Power Supplies, continued
6. Plug the supplied 18-pin jumper into the header on the back of the DSM3 Series circuit board.
NOTE:
To prevent damage to the DSM3, do not reuse the existing 18-pin connector.
Instead, use the jumper supplied with the transponder.
Fig. 7-2, The 18-pin jumper
(Alpha p/n 540-286-19)
Fig. 7-3, The 18-pin jumper installed
7. Line up the 18-pin jumper with the header on the Inverter Module and connect the unit to the
Inverter Module.
Fig. 7-4, Connecting the Transponder to the Inverter Module
8. Fasten the DSM3 Series to the Inverter Module by tightening the two captive screws. It is
recommended that the screws be tightened alternately, a few turns at a time so the transponder
aligns in parallel to the Inverter Module.
9. Reinstall the Inverter Module and reconnect the ribbon cable. Make front panel connections
(tamper, temperature sensor, battery sense, RF etc.).
10. If not yet done, record the cable modem MAC address from the front of the unit and report it to
the network manager for network provisioning.
42
745-814-B8-001, Rev. A (08/2011)
7.0 Installation
7.3
DPM Installation / Replacement Procedure
If the XM2-300HP High-Efficiency CableUPS has been shipped without a DPM, or the existing module
requires removal and replacement, do so via the the following procedure:
1. Switch OFF the power supply’s battery breaker.
NOTE:
With the battery breaker in the OFF position, the power supply will not go into inverter mode.
2. Unplug all Inverter Module connections (e.g. battery cable, remote temperature sensor).
3
3
1
4
2
3
Fig. 7-5, Removing the Inverter Module from the Power Supply
3. Loosen the Inverter Module thumbscrews.
4. Slide the Inverter Module out of the power supply.
5. Loosen the two Phillips captive screws to remove the DPM sheet metal from the Inverter Module.
Captive Screw
Captive Screw
Fig. 7-6, Removing the DPM sheet metal from the Inverter Module
745-814-B8-001, Rev. A (08/2011)
43
7.0 Installation
7.3
DPM Installation Procedure, continued
6. Plug the supplied 18-pin jumper into the header on the Inverter Module.
6
Fig. 7-8, DPM 18-pin header
(Alpha p/n 540-581-19)
Fig. 7-7, The 18-pin jumper installed
7. Attach the DPM to the sheet metal with the supplied
6-32 screws.
8. Line up the 18-pin jumper with the header on the
Inverter Module and connect the unit to the inverter
module.
9. Fasten the DPM to the Inverter Module by tightening
the two captive screws. It is recommended that the
screws be tightened alternately, a few turns at a time
so the transponder aligns in parallel to the Inverter
Module.
10. Reinstall the Inverter Module and make front panel
connections (tamper, temperature sensor, battery,
RF, etc.).
Fig. 7-9, DPM attached to sheet metal
11. If not yet done, record the cable modem MAC
address from the front of the unit and report it to the
network manager for network provisioning.
NOTE:
When replacing an existing DPM do not reuse
the existing 18-pin connector. Use the18-pin
connector supplied with the DPM.
Fig. 7-10, DPM / IM connection
Fig. 7-11, Completed assembly
44
745-814-B8-001, Rev. A (08/2011)
7.0 Installation
7.4
DSM3x LEDs and Connections
Item
1
12
LED or Connector
Status
Behavior
N/A
OFF
No power or malfunctioning DSM3 Series
ON
Reset of the DSM3 Series is in process
Steady Blinking
Normal operation
Blinking more
OFF than ON
Minor Alarm
Blinking more
ON than OFF
Major Alarm
OFF
No power, upstream frequency undetermined
OFF / ON
Power on, downstream locked, upstream
frequency ranging, DHCP request in progress
ON
CMTS registration completed
OFF
No power / downstream carrier
OFF / ON
Power on, downstream carrier frequency searching
GRN
1
2
ALM/RDY: Alarm
and Ready
RED
13
3
14
2
4
5
15
3
6
16
9
11
DS: Downstream
RF Carrier detection
and lock
GRN
ACT: CPE Activity
status
GRN
5
LNK: CPE Link
status
GRN
RF Rx/Tx Power
Level Indicator
TRI
17
8
10
GRN
4
6
7
REG: Upstream
ranging and
registration lock
18
Indication
ON
Downstream carrier lock
OFF
No Ethernet communications activity
OFF/ON
Momentary flash during CPE communications via
the Ethernet craft port
OFF
No Ethernet link
ON
Link on Ethernet Craft port
OFF
No RF detected
Blue
Rx/Tx Power at a warning level as set within the
SCTE-HMS Property Table
Green
Rx/Tx RF Power level within tolerance
Red
Rx/Tx Power at an alert level as set within the
OFF
No AlphaBus Communications
OFF/ON
Momentary flash - AlphaBus Port communications
active
7
COM: AlphaBus
communications
GRN
8
BAT A/B
GRN
ON/OFF
ON (steady) if battery string(s) connected correctly
9
BAT A/B Connector
10
BAT C/D
GRN
ON/OFF
11
BAT C/D Connector
12
RST: Reset buttton
13
ENV: Environmental Control connector
14
TPR: Tamper Switch connector
15
ETH: Ethernet connection
16
RF Connection
17
COM: AlphaBus Communications connector
18
RF, CPE MAC Address label
Fig. 7-12, DSM3x LEDs and Connectors
745-814-B8-001, Rev. A (08/2011)
45
7.0 Installation
7.5
DSM3 LEDs and Connections
Item
1
Status
Behavior
Indication
N/A
OFF
No power or malfunctioning transponder
GRN
8
1
2
LED or Connector
ALM/RDY: Alarm and
Ready
RED
3
9
2
4
REG: Upstream
ranging and
registration lock
GRN
10
5
DS: Downstream RF
Carrier detection and
lock
GRN
4
ACT: CPE Activity
status
GRN
5
LNK: CPE Link status
GRN
3
6
11
6
7
12
RF Rx/Tx Power Level
Indicator
TRI
7
BAT A/B
GRN
8
RST: Reset buttton
9
10
11
RF Connection
12
RF, CPE MAC Address label
ON
Transponder reset in process
Steady Blinking
Normal operation
Blinking more
OFF than ON
Minor Alarm
Blinking more
ON than OFF
Major Alarm
OFF
BLINKING
frequency ranging, DHCP request pending
ON
OFF
BLINKING
ON
OFF
BLINKING
the Ethernet Craft port
OFF
No link
ON
OFF
No RF detected
Blue
Green
Red
ON/OFF
ON (steady) if battery string(s) connected correctly.
Fig. 7-13, DSM3 LEDs and Connectors
46
745-814-B8-001, Rev. A (08/2011)
7.0 Installation
7.6
DPM Connections
1
7
2
Item
LED or Connector
Status
Behavior
Indication
N/A
OFF
No power or malfunctioning transponder
8
GRN
3
9
1
ALM/RDY: Alarm and
Ready
RED
4
10
5
2
REG: Upstream
ranging and
registration lock
GRN
6
3
DS: Downstream RF
Carrier detection and
lock.
GRN
11
4
ACT: CPE Activity
status
GRN
5
GRN
6
RF Rx/Tx Power Level
Indicator
TRI
ON
Transponder reset in process
Steady Blinking
Normal operation
Blinking more
OFF than ON
Minor Alarm
Blinking more
ON than OFF
Major Alarm
OFF
BLINKING
frequency ranging, DHCP request pending
ON
OFF
BLINKING
ON
OFF
BLINKING
the Ethernet Craft port
OFF
No link
ON
OFF
No RF detected
Blue
Green
Red
7
RST: Reset buttton
8
ENV: Environmental Control connector
9
10
11
RF Connection
Fig. 7-14, DPM LEDs and Connectors
745-814-B8-001, Rev. A (08/2011)
47
7.0 Installation
7.7
Connecting the RF Drop
CAUTION!
Install a grounded surge suppressor (Alpha P/N 162-028-10 or equivalent).
Connect the RF drop according to the diagram below. The RF drop must have a properly installed
ground block in the power supply enclosure. Recommended downstream RF level is 0 dBmV.
Connect any other front panel connections at this time (e.g. battery strings, tamper switch).
Grounded Surge Protector
(See Caution Above)
RF Cable
to Headend
Fig. 7-15, Connecting the RF Drop
7.8
Front Panel Connections
ECM to SCM Interface
(Alpha P/N 704-709-20)
AlphaBus Cable
Linked CableUPS
Serial Interface Cards
DSM3 Series in
Primary XM2
B
B
S
Y
S
S
Y
S
C
O
M
C
O
M
A
(Alpha P/N 875-190-20 for 6',
21 for 9', 22 for 18', 23 for 35')
Environmental/LA-P-SM connection
Ethernet connection
A
RF connection
A
C
Generator (ECM)
Battery Sense Wire Harness
Refer to Section 8 for part numbers and wiring
options.
A
Comm Port
Connections
B
System Port
Connections with more
than one power supply
C
Battery Sense Connections
Fig.7-16, System Interconnection Diagram
48
745-814-B8-001, Rev. A (08/2011)
7.0 Installation
7.9
Environmental and LA-P-SM Connections
The DSM3x and DPM have the capability to monitor and control enclosure environmental heating and
cooling. Typically this is used for battery mat heaters in cold environments, however the functionality may
be implemented to control enclosure fans or air conditioners. The following section will outline the details
of the controls available and will include an example of a typical battery heater mat configuration and
explanation of the settings.
7.9.1 Connecting the Battery Heater Mat Controller
Power to the heater mat is provided via a customer-supplied controller plugged into the power
outlet inside the enclosure. A cable (Alpha p/n 875-627-22) connects the controller to the ENV
(Environmental) connector on the DSM3x and DPM. The connection procedure is shown below.
1. Connect the 4-pin connector from the controller cable
(Alpha p/n 875-627-22) into the base of the Heater Mat
Controller.
2. Plug the controller into the power outlet.
3. Plug the Heater Mat into the controller.
4. Plug the 6-pin connector into the ENV connector.
Once the connection has been made, Environmental Control Management can be configured on
the transponder's Web page as indicated in the following tables. The Environmental Control MIB
section begins at atiMgmtSysTempMgr (1.3.6.1.4.1.926.1.3.2.4).
Status of the Environmental Control is also available on the transponder’s Web page.
745-814-B8-001, Rev. A (08/2011)
49
7.0 Installation
7.10
Environmental Control MIBs
atiMgmtSysTempCtrl (1.3.6.1.4.1.926.1.3.2.4.1)
Value list
Description
off(1)
Temperature device is off. This setting is non-volatile, if the variable is in this state upon reset (or power-up) this value will be
retained. This is the DEFAULT factory value for this variable.
onTimer(2)
Temperature device turned on for a predefined time. Before a SET to this state is issued, atiMgmtSysTempTimer is to be SET with
the number of minutes the heater or cooler is to be on. When the timer has expired, this variable will automatically be set to 1.
onTemp(3)
Temperature device controlled by the battery temperature probe. Before a SET to this state, atiMgmtSysTempTemperature and
atiMgmtSysTempHysteresis must be set to the desired temperature values. Once placed into this state, this variable will not
change until another SET to this OID is received. Temperature control is based on the battery temperature probe. If there appears
to be no battery temperature probe, the output to the temperature device will be inactive.
onTimerTemp(4)
Temperature device will be controlled by both the temperature and timer values. When set to this state, the temperature device will
be controlled as if this variable is in state 3, but only for the time defined by atiMgmtSysTempTimer. Once the timer has counted
down to zero, the value of this variable will be returned to 1. This value is volatile, after reset, the state of this variable will be 1 if it
was in this state before the reset.
on(5)
Temperature device is on. This value can be used when the temperature device has a thermostat of its own. However it is recommended, as a safety precaution, that state 3 is used with the battery temp probe being used as a back up in case the device thermostat gets stuck in the "on" state (provided the transponder is connected to the temperature device’s power control). This state
/ mode could also be used if the temperature control line was used for something other than a temperature control. This value is
non-volatile and will remain in this state after a reset.
atiMgmtSysTempStatus (1.3.6.1.4.1.926.1.3.2.4.2)
Value list
Description
contactOpen(1)
The value of this variable reflects the state of the feedback signal from the temperature device. Since not all temperature devices
have a feedback signal, or the operation of the feedback signal may vary from device to device, the meaning of this signal is
implementation specific.
contactClosed(2)
atiMgmtSysTempMode (1.3.6.1.4.1.926.1.3.2.4.3)
Value list
Description
heater(1)
Mode of Operation. The temperature device may be a heater (such as a battery mat) or a cooler (such as an enclosure fan). When
this device is acting as a thermostat, this variable defines the active state. If this variable is set to "heater", the temperature device
will be active only when the temperature is below the defined level. If this variable is set to "cooler", the temperature device will be
activated when the temperature is above the defined level. The DEFAULT factory setting for this variable is heater(1). This variable
is non-volatile and its value will be retained when the device is reset.
cooler(2)
atiMgmtSysTempActiveState (1.3.6.1.4.1.926.1.3.2.4.4)
Value list
Description
closed(1)
This variable defines how this device creates the active state. When this variable is set to "closed(1)" the active state will be represented by the drive pin being shorted to ground and high impedance will represent the inactive state. When this variable is set
to "open(2)" the active state will be represented by the drive pin being high impedance in the active state and shorted to ground in
the inactive state. The DEFAULT factory state for this variable will be 1. This variable is non-volatile and the value will be retained
when the device is reset.
open(2)
50
745-814-B8-001, Rev. A (08/2011)
7.0 Installation
7.10
Environmental Control MIBs, continued
atiMgmtSysTempTemperature (1.3.6.1.4.1.926.1.3.2.4.5)
Size list
Description
1...70
Thermostatic temperature setpoint in degrees centigrade. When this device is set to control the temperature device based on
temperature, this variable (along with the hysteresis variable) will be used to determine when the temperature device is to be
turned on and off. This value is compared to the value from the battery temperature sensor. The DEFAULT factory state for this
variable will be 0 (once changed, it may not be put back to zero, providing an indication that the value has been adjusted). This
variable is non-volatile and the value will be retained when the device is reset.
atiMgmtSysTempHysteresis (1.3.6.1.4.1.926.1.3.2.4.6)
Size list
Description
1...10
When the device is controlling the temperature device thermostatically, this value is used to keep the temperature device from
going on and off too often. If the temperature device is a heater, the device will be turned on when the temperature reaches the
setpoint but will not be turned off until the detected temperature overshoots the set point by this amount. When the temperature
device is a cooler, the device will be turned on when the temperature reaches the set point, but will not turn off until the detected
temperature undershoots the set point by this amount. The DEFAULT factory state for this variable is 1. This variable is nonvolatile and the value will be retained when the device is reset.
atiMgmtSysTempTimer (1.3.6.1.4.1.926.1.3.2.4.7)
Size list
Description
0...1440
When the temperature device is controlled using the timer, this is the number of minutes the temperature device will be active.
The DEFAULT factory state for this variable is 30. This variable is non-volatile and the value will be retained when the device is
reset.
atiMgmtSysTempCountdown (1.3.6.1.4.1.926.1.3.2.4.8)
Size list
Description
0...1440
When the temperature device is controlled using the timer, this is a countdown that will indicate how many minutes before
the device will become inactive. The value of this counter is undefined when the device is not active in a timer mode. Anytime
atiMgmtSysTempCtrl is SET to a value that indicates timer mode, the value of atiMgmtSysTempTimer will be copied into this
variable. If, while this variable is counting down, atiMgmtSysTempCtrl is again SET to a value that represents a timer mode,
the value of atiMgmtSysTempTimer will again be copied into this variable and the count will start over again. The temperature
device will change to inactive when this count drops to zero. At zero the counter will stop.
atiMgmtSysTempStatusInvert (1.3.6.1.4.1.926.1.3.2.4.9)
Value list
Description
noInvert(1)
The default value of this variable is noInvert(1), which provides a contact closure when the temperature device is on. When
this parameter is set to invert(2), the returned value for the contact status (atiMgmtSysTempStatus) will be inverted (contact
closed will be reported as open, contact open will be reported as closed). This accommodates the differences in which the
manufacturers of the relay block have implemented the open versus closed status contacts. This variable is non-volatile and the
value will be retained when the device is reset.
invert(2)
745-814-B8-001, Rev. A (08/2011)
51
7.0 Installation
7.11
Configuring the Battery Heater Mat Controller
In this example, values are written to their respective OIDs to set temperatures, control mode and
status reporting:
Set these OIDs to the specified value
Functionality
atiMgmtSysTempTemperature (1.3.6.1.4.1.926.1.3.2.4.5) to 5
Heater turns on at 5°C
atiMgmtSysTempHysteresis (1.3.6.1.4.1.926.1.3.2.4.6) to 3
3°C of permitted controller overshoot (in this case, would turn off at 8°C)
atiMgmtSysTempCtrl (1.3.6.1.4.1.926.1.3.2.4.1) to 3
Battery temperature sensor used to control heater setpoint
atiMgmtSysTempMode (1.3.6.1.4.1.926.1.3.2.4.3) to 1
Places controller in heater mode
atiMgmtSysTempActiveState (1.3.6.1.4.1.926.1.3.2.4.4) to 1
Drive pin to the temperature device will go low when heater is on
atiMgmtSysTempStatusInvert (1.3.6.1.4.1.926.1.3.2.4.9) to 1
Sets the polarity of the feedback signal from the temperature device
During operation, the following MIB points will report the current temperature and whether the
heater is on or off.
52
SNMP MIB Point
Data
atiMgmtSysTempStatus (1.3.6.1.4.1.926.1.3.2.4.2)
Temperature device ON or OFF
atiBBSysViewBatteryTemperature (1.3.6.1.4.1.926.1.4.1.1.3.5)
Battery temperature (in degrees C)
745-814-B8-001, Rev. A (08/2011)
7.0 Installation
7.12
Connecting the LA-P-SM
The DSM3x Series and DPM transponders are capable of monitoring the status of the Alpha
LA-P-SM series surge suppressors. The physical installation is shown below and consists of
connecting the cable (Alpha p/n: 875-627-23) from the LA-P-SM's two leftmost screw terminals to
the six pin ENV connector on the DSM3x or DPM and plugging the LA-P-SM into the enclosure‘s
power outlet.
1. Insert cable into 3-pin
connector
2. Tighten to .22 to .25N•m
4. Plug LA-P-SM into power outlet
3. Connect to LA-P-SM
5. Plug cable into ENV connector
7.12.1 Configuring the LA-P-SM
A MIB value must be set to enable monitoring via SNMP or the transponder’s Web page. To
do this, set the following OID to a value of 2 (installed). On the Web page, go to the "Advanced
Configuration" on the main menu and then click on the sub-menu "IO-Environment". Click the
"Installed" button.
For help accessing the transponder Web page, consult Section 4.
atiMgmtSysLAPInstalled (1.3.6.1.4.1.926.1.3.2.8.1)
Once this OID has been set, the following information will be available via SNMP and the Web
page:
atiMgmtSysLAPState (1.3.6.1.4.1.926.1.3.2.8.2)
Value list
Description
notInstalled(1)
NO LAP INSTALLED. This would be the case if the OID atiMgmtSysLAPInstalled has not been set to a value of 2.
ok(2)
OK. Indicates that each connected power supply detects AC input and the LAP device reports no fault. Normal operation.
acNotPresent(3)
AC OFF. One or more of the power supplies detects no AC. To check if the LAP has failed, query the OID psInputVoltagePresence (1.3.6.1.4.1.5591.1.4.2.1.34) to ascertain if the line has truly failed; if this is the case, the LAP is
working normally. If the line is OK, it is likely the LAP has a problem.
relpaceLap(4)
Critical Surge Event - Replace LAP. An LAP has failed and should be replaced. This is the state when all power supplies detect AC but the LAP sense line indicates a fault.
invalid(5)
There is a fault, either the LAP has not been wired correctly or the relay in the LAP is stuck in the no-fault state. This
state occurs when at least one power supply senses AC fail, which should cause an LAP fault, but no fault is detected
(this would be the case if the LAP relay is stuck in the ON condition).
7.12.2 Simultaneous Usage, Environmental Control and LA-P-SM
The environmental control and the LA-P-SM may be implemented simultaneously. This
configuration requires interface cable Alpha part number 875-627-24. Control and monitoring
are identical to the devices being used independently. Sections 7.9 through 7.12 may be used to
install, connect, and set MIB points for operation.
745-814-B8-001, Rev. A (08/2011)
53
8.0 Battery Sense Wire Kits
8.1
36V Single and Dual Strings
To Power Supply
Red
Black
NEG
NEG
3A
NEG
2A
POS
1A
POS
POS
2
7
3
8
4
Vbatt 1A [C] 12V
Pin 2
6
Vbatt 2A [C] 24V
Pin 3
1
Vbatt 3A [C] 36V
Pin 4
5
A/B [C/D] NEG
Pin 1
Fig. 8-1, 36V System, Single String
Sense Wire Kits:
Alpha P/N: 874-842-21 (6')
Alpha P/N: 874-842-27 (9')
Back of Plug
To Power Supply
Red
Black
NEG
NEG
3A
NEG
2A
POS
1A
POS
POS
8
4
Back of Plug
NEG
3B
POS
54
Vbatt 1A [C] 12V
Pin 2
3
Vbatt 2A [C] 24V
Pin 3
7
Sense Wire Kits:
Alpha P/N: 874-842-20 (6')
Alpha P/N: 874-842-28 (9')
Vbatt 1B [D] 12V
Pin 5
2
Vbatt 2B [D] 24V
Pin 6
6
Vbatt 3A [C] 36V
Pin 4
1
Vbatt 3B [D] 36V
Pin 7
5
A/B [C/D] NEG
Pin 1
Fig. 8-2, 36V System, Dual String
NEG
2B
POS
NEG
1B
POS
745-814-B8-001, Rev. A (08/2011)
8.0 Battery Sense Wire Kits
8.2
48V Single and Dual Strings
To Power Supply
Red
NEG
7
3
8
4
POS
POS
Vbatt 2A [C] 24V
Pin 3
2
Vbatt 4A [C/D] 48V
Pin 8
6
A/B [C/D] NEG
Pin 1
POS
NEG
2A
Vbatt 3A [C] 36V
Pin 4
3A
4A
1
NEG
1A
POS
Vbatt 1A [C] 12V
Pin 2
NEG
5
Black
To Power Supply
Back of Plug
Fig. 8-3, 48V, Single String
Black
Red
Sense Wire Kits:
3A
2
7
3
8
4
Back of Plug
Fig.8-4, 48V, Dual String
Sense Wire Kits:
Alpha P/N: 874-841-20 (6')
Alpha P/N: 874-841-24 (9')
Vbatt 3B [D] 36V
Pin 7
6
NEG
4B
POS
745-814-B8-001, Rev. A (08/2011)
POS
A/B [C/D] NEG
Pin 1
1
Vbatt A/B [C/D] 48V
Pin 8
5
2A
NEG
3B
POS
1A
POS
Vbatt 3A [C] 36V
Pin 4
POS
NEG
POS
Vbatt 1B [D] 12V
Pin 5
4A
NEG
Vbatt 1A [C] 12V
Pin 2
NEG
Vbatt 2A [C] 24V
Pin 3
NEG
Vbatt 2B [D] 24V
Pin 6
Alpha P/N: 874-841-21 (6')
Alpha P/N: 874-841-25 (9')
NEG
2B
POS
NEG
1B
POS
55
9.0 Start Up and Verification
9.1
Initial Startup and Local Verification
To confirm successful hardware installation before leaving the installation site, verify network connectivity
and correct hardware interconnection.
To Verify Network Connectivity:
The DS and REG LEDs on the front of the DSM3 Series should be ON solid green. This indicates
successful registration with the headend. In addition, the RF LED should also be ON solid green
indicating proper RF power levels and the ALM/RDY LED should be blinking green for normal
operation.
With the DSM3 Series used in conjunction with the XM2-HP power supply, network connectivity
can be verified via the smart display. For other power supply models, verify the network status via
the Ethernet port.
Connect a computer’s network port to the transponder’s Ethernet port using a standard network
cable. Launch an Internet browser and enter 192.168.100.1 into the Address. The transponder
will return the Web page shown below. Click on “General” to display the key communications
parameters including upstream and downstream power levels and the cable modem’s IP address,
which confirms connectivity.
®
General HMS
HMS
Alarms
Advanced
Settings
Alarms
Advanced
Settings
APPS
HISTORY
PrintPrint
Communications
Configuration
SysUpTime
Firmware Version
2IP US
7 days 11H:13m:17s
4.4.6.0_02.00_NA
CM
CPE Transponder
MAC Address
IP Address
00:90:EA:00:30:84
192.168.1.124
00:90:EA:00:30:85
192.168.1.120
CM Tx (dBmV)
42.0
CM Rx (dBmV)
3.2
41.0
+50
0
-20
SNR (RxMER)
55
60
3.2
-15
-10
15
10
20
44.2
System Name
Alpha
System Location
Bellingham
System Contact
John Doe
Common Logical ID
DSM3
SET
Power Supplies
Device 1
Model
ALPHA / XM2
Firmware
7.03.0
Major Alarm
Minor Alarm
Inverter Status
Tamper
OK
OK
OFF
Closed
Self Test
Start Test
Temperature 1 (°C)
Input Voltage (V)
Output Voltage (V)
41.60
15
124.80
89.00
1.00
Status
Actstate
Mode
Temperature
Hysteresis
Timer
Countdown
Contact Open
Closed
Heater
24
2
1
0
LAP
Not Installed
Not Installed
Batteries
String 1
String 2
Battery 1 (V)
Battery 2 (V)
Battery 3 (V)
13.90
13.95
13.95
14.00
14.00
13.90
Fig.9-1, Initial Web Page
56
745-814-B8-001, Rev. A (08/2011)
9.2
Verifying Correct Hardware Interconnection
The BAT A/B and BAT C/D LED indicators on the front panel of the DSM3 Series unit should illuminate
solid green once the battery wiring harnesses are correctly installed.
NOTE:
The DSM3x model provides both BAT A/B and BAT C/D LED indicators and battery harness connectors
(supports a maximum 4 battery strings). The DSM3 model provides only the BAT A/B LED indicator and
battery harness connector (supports a maximum 2 battery strings).
From the Power Supplies and Batteries section of "General" tab of the DSM3 Series Web page, the
following screen will be visible and the parameters shown will be available for viewing and verification.
To test hardware interconnection using the Ethernet port, verify valid values for Output Voltage, Output
Current and individual battery voltages.
General
Settings
General HMS
HMSAlarms
AlarmsAdvanced
Advanced
Settings APPS
HISTORY
Power Supplies
Device 1
Model
ALPHA/XM2
Firmware
5.07.0
Major Alarm
OK
Minor Alarm
OK
Inverter Status
OFF
Tamper
Closed
Self Test
Start Test
0 Days, 0 Hrs, 0 Mins and 0 Secs
0 Days, 0 Hrs, 0 Mins and 0 Secs
43.00
Battery Temperature 1 (C)
30
Input Voltage (V)
120.00
Output Voltage (V)
89.00
11.60
Status
Actstate
Mode
Temperature
Hysteresis
Timer
Countdown
ContactOpen
Closed
Heater
0
2
30
0
LAP
Not Installed
Not Installed
Batteries
Battery 1 (V)
Battery 2 (V)
Battery 3 (V)
String 1
10.20
10.25
10.30
String 2
10.25
10.25
10.30
Fig.9-2, General Tab Screen
745-814-B8-001, Rev. A (08/2011)
57
9.4
System Status Indicators and Reset button
As viewed from the front of the unit, the DSM3 Series utilizes light emitting diodes (LEDs) to indicate
system status. During system startup, the LEDs will first blink momentarily then indicate the current status
of a variety of parameters on the DSM3 Series transponder. The LEDs indicate alarms, RF power level
status, battery string connectivity and communications activity with the network. A description of each LED
follows.
LED
N/A
ALM/RDY
REG
Status
GRN
ALM/RDY: Alarm and Ready
DS
RED
ACT
LNK
REG: Upstream ranging and
registration lock.
GRN
RF
DS: Downstream RF Carrier
detection and lock.
COM
GRN
ACT: CPE Activity status
GRN
GRN
BATT A/B
BATT C/D
RF Rx/Tx Power Level Indicator
TRI
Behavior
Indication
OFF
No power or malfunctioning DSM3 Series
ON
Reset of the DSM3 Series is in process
Steady Blinking
Normal operation
Blinking more OFF than ON
Minor Alarm SCTE-HMS configured
Blinking more ON than OFF
Major Alarm SCTE-HMS configured
OFF
OFF / ON
Power on, downstream locked, upstream frequency ranging,
DHCP request in progress
ON
OFF
OFF / ON
ON
OFF
OFF/ON
Momentary flash while CPE communications ongoing via
the Ethernet craft port
OFF
No Ethernet link
ON
OFF
No RF detected
Blue
Green
Red
OFF
No AlphaBus Communications
OFF/ON
Momentary flash - AlphaBus Port communications
active
COM: AlphaBus
communications.
GRN
BATT A/B
GRN
ON/OFF
BATT C/D
GRN
ON/OFF
Fig. 9-3, LED Functionality and Indications
9.4.1 Detailed LED Descriptions
After power is applied or a reset occurs, all LED's will flash in certain patterns indicating the cable
modem chipset is starting or restarting. Once it is ready it will begin the DOCSIS requirement of
searching for the downstream frequency lock and the LED's will follow the detailed descriptions
below.
ALM/RDY - Alarm/Ready
The ALM/RDY - During normal operation, this LED blinks GREEN, indicating a heartbeat pulse
from the processor. The frequency of flashing by this LED provides a visual alert for power
supply discrete major and minor alarms, if configured in the property and discrete property tables
of the SCTE-HMS MIB. The ALM LED (RED) is factory defaulted OFF. Refer to Section 6.3
for information on configuring the DSM3 Series for active monitoring and alarming. If an event
triggers an HMS alarm, the ALM/RDY LED blinks RED according to the alarm type until the alarm
has been resolved. For a minor alarm, the frequency of flashing (RED) will be more OFF than
ON and for a major alarm the frequency of flashing will be (RED) more ON than OFF. If there are
multiple active alarms, including one or more major alarms with one or more minor alarms, the
major alarm will take precedence in terms of the indication.
58
745-814-B8-001, Rev. A (08/2011)
9.4.1
Detailed LED Descriptions, continued
REG - CM Registration
Once a downstream channel has been negotiated between the CM and CMTS, the modem
attempts to register with the DHCP server and obtain the configuration file. This LED flashes
while the process takes place. Once the registration is complete, the LED will remain on solid.
This is the best indication that the DSM3 Series is communicating with the CMTS in the headend.
DS - Downstream Communication
This LED indicates the state of the CM's attempt to gain a downstream signal. This process may
take several seconds, depending on how long it takes the CM to locate a carrier signal and lock
onto a channel. The LED flashes while searching for the downstream DOCSIS channel and is on
solid when the downstream channel is locked.
ACT - CPE Activity
The CPE activity LED flashes to indicate that data is being transmitted or received between the
DSM3 Series and a network device.
LNK - Network Communication Status
The Ethernet link LED remains ON when there is an active connection on the Ethernet port (e.g.,
a computer is connected for local diagnostics).
Rx/Tx Power
The Rx/Tx PWR LED utilizes a tricolor LED to provide the installer a quick verification of the modem transmit (Tx) and receive (Rx) RF power levels. The Rx/Tx PWR LED will illuminate “green”
when both the cable modem Tx and cable modem Rx RF power levels are within the range as
specified in the SCTE-HMS PropertyTable. The LED indicator illuminates “blue” when Rx and/or
Tx levels are within the “warning” range as specified by the SCTE-HMS PropertyTable. The LED
indicator illuminates “red” when Rx and/or Tx levels are outside the range as specified by the
SCTE-HMS PropertyTable.
Refer to the following table for default ranges in the SCTE-HMS PropertyTable:
Parameter
alarm Enable
HiHi
Hi
Lo
LoLo
Deadband
Rx
docsIfDownChannelPower
(OID:1.3.6.1.2.1.10.127.1.1.1.1.6)
00
(0F*)
150
100
-100
-150
15
Tx
docsIfCmStatusTxPower
(OID:1.3.6.1.2.1.10.127.1.2.2.1.3)
00
(0C*)
550
500
00
00
15
* Values in ( ) denote behavior of the Rx/TX LED if alarmEnable bits are set to ‘00’.
By default, alarmEnable is set to 00 (disabled) to prevent unwanted SNMP traps but the LED
behavior will function as if the alarmEnable were set to the values in the above table. If the alarm
Enable bits are set to anything other than 00 the LEDs will then follow the behavior of the desired
enable bit setting.
The above default values translate into the following Rx/Tx Power LED color ranges:
LED Color
Rx Range (dBmV)
Tx Range (dBmV)
Green
+10 to -10
0 to +50
Blue
+15 to +10 and -10 to -15
+50 to +55
Red
>+15 and <-15
>+55
In addition to the above SCTE-HMS PropertyTable entries, the Tx and Rx levels displayed on the
DSM3 Series Web page will each provide colored indicator bars that correlate to the RF LED and
SCTE-HMS PropertyTable thresholds.
745-814-B8-001, Rev. A (08/2011)
59
9.4.1
Detailed LED Descriptions, continued
Rx/Tx Power, continued
The current RF level status for both the Rx and Tx will be displayed on the colored scale
highlighted in black, providing verification of modem RF power levels. Refer to the figure below
for an example of the RF power level indicator bars on the Web page.
®
General
Alarms
Advanced
Configuration
GeneralHMSHMS
Alarms
Advanced
Settings
APPS
Print Print
HISTORY
Communications
Configuration
SysUpTime
Firmware Version
2IP US
7 days 11H:13m:17s
4.4.6.0_02.00_NA
CM
CPE Transponder
MAC Address
00:90:EA:00:30:84
00:90:EA:00:30:85
IP Address
CM Tx (dBmV)
192.168.1.124
42.0
192.168.1.120
CM Rx (dBmV)
3.2
SNR (RxMER)
44.2
41.0
+50
0
55
60
3.2
-20
-15
-10
10
15
20
Copyright © 2010, AlphaTechnologies Inc., All Rights Reserved
Fig.9-4, DSM3 Series Web Page, RF Power Level Indicators
Configuring the Rx/Tx Power LED - Custom Settings
If desired, the RF Power Level ranges for the Rx/Tx PWR LED may be customized via
SNMP by adjusting the HiHi, Hi, Lo, LoLo values for the docsIfDownChannelPower and
docsIfCmStatusTxPower in the SCTE-HMS Property Table (OID:1.3.6.1.4.1.5591.1.1.1). Be
careful not to exceed the Input Level and Output Power range specifications of the DSM3 Series
transponder.
COM - AlphaBus Communications
The COM LED indicates any data traffic being received by the DSM3 Series through the COM
(AlphaBus) port. This LED will also blink with one to three blinks approximately every 10 seconds,
which indicates communication exists between the DSM3 Series and other connected devices,
such as a generator or additional XM2.
BAT A/B - Battery Strings A & B
The LED indicator remains ON solid when the battery string wiring harness is correctly connected
to the batteries and the Bat A/B connector on the DSM3 and DSM3x Series.
BAT C/D - Battery Strings C & D
The LED indicator remains ON solid when the battery string wiring harness is correctly connected
to the batteries and the Bat C/D connector on the DSM3x.
9.4.2 Resetting the Transponder
Should the need arise to reset the transponder locally, such as in the case of adding additional
power supplies, a generator, or carrying out maintenance activities, do the following:
Press and hold the reset button (RST) for approximately three (3) seconds until the ALM/RDY
LED stops blinking and turns solid (green). Release the button. The transponder will perform its
power up sequence.
9.5
Verifying Communications via the Headend
Using SNMP, check connectivity by verifying power supply data by doing the following:
• With a MIB browser check power supply data in the psIdent MIB branch (1.3.6.1.4.1.5591.1) of the
SCTE-HMS tree.
• With network management software, verify the DSM3 Series has been identified and is reporting data
correctly.
60
745-814-B8-001, Rev. A (08/2011)
10.0 Alpha MIB Parameters
10.1
Definitions and Settings
The following tables display commonly-configured Alpha MIB parameters and provide specific information
with regard to functionality, options, OIDs, types and variables.
NOTE:
The Alpha MIB Definitions and Settings are subject to change without notice and should only be used
for advanced diagnostics. The SCTE-HMS MIBs listed in Section 6 should be implemented for status
monitoring & control.
Parameter
OID
Description
Access
Type
Value
atiMgntSnmp
1.3.6.1.4.1.926.1.3.1.0
Object
Identifiers
atiMgmtSnmpTrapTable
1.3.6.1.4.1.926.1.3.1.1
Object
Identifiers
atiMgmtSnmpTrapAddress.1
1.3.6.1.4.1.926.1.3.1.1.1.2.1
SNMP Trap Address (1)
Read/Write
IP Address
0.0.0.0 (default)
1.3.6.1.4.1.926.1.3.1.1.1.2.2
Read/Write
IP Address
0.0.0.0
1.3.6.1.4.1.926.1.3.1.1.1.2.3
Read/Write
IP Address
0.0.0.0
1.3.6.1.4.1.926.1.3.1.1.1.2.4
Read/Write
IP Address
0.0.0.0
SNMP TRAP ADDRESSES
SECURE SNMP ACCESS ADDRESS
atiMgmtSnmpAccessTable
1.3.6.1.4.1.926.1.3.1.2
Object
Identifiers
atiMgmtSnmpAccessAddress.1
1.3.6.1.4.1.926.1.3.1.2.1.2.1
Secure IP Address (1)
Read/Write
IP Address
0.0.0.0 (default)
1.3.6.1.4.1.926.1.3.1.2.1.2.2
Read/Write
IP Address
0.0.0.0
1.3.6.1.4.1.926.1.3.1.2.1.2.3
Read/Write
IP Address
0.0.0.0
1.3.6.1.4.1.926.1.3.1.2.1.2.4
Read/Write
IP Address
0.0.0.0
SNMP ACCESS ENABLE
atiMgntSnmpAccess
1.3.6.1.4.1.926.1.3.1.3.0
atiMgmtSnmpSnmpv1Access
1.3.6.1.4.1.926.1.3.1.3.1.0
atiMgmtSnmpSnmpv2Access
1.3.6.1.4.1.926.1.3.1.3.2.0
Object
Identifiers
SNMPv1 Access to Power
Supply Data
Read/Write
SNMPv2c Access to Power
Supply Data
Read/Write
Integer
1 = Disable
2 = Enable (Default)
Integer
1 = Disable
CPE & SECURITY KEY (Dual IP)
atiMgmtSnmpAlphaSetAccess
1.3.6.1.4.1.926.1.3.1.3.3.0
"Set to Data Access Key
Read/Write
Octet String
Set to match the value
of the Data Access Key
atiMgmtSnmpAlphaSetKey)
CIBSET (default)"
atiMgmtSnmpAlphaSetKey
1.3.6.1.4.1.926.1.3.1.3.4.0
Data Access Key (Dual IP)
Read/Write
Octet String
CIBSET (default)
atiMgmtSnmpCPESetEnabled
1.3.6.1.4.1.926.1.3.1.3.5.0
Corresponds to whether
or not the action taken on
was successful. Once
enabled, writing 1(false)
to this variable will disable
CPE sets.
Read/Write
Integer
1=Disabled (False)
Enables the CPE interface Dual IP mode.
Read/Write
atiMgmtSnmpSnmpCPEAccess
1.3.6.1.4.1.926.1.3.1.3.6.0
2=Enabled (True)
Integer
1=Disabled (Single IP)
2=Enabled (Dual IP)
CPE SETTINGS (Dual IP)
atiMgmtSysMonitoringCpeStaticMode
1.3.6.1.4.1.926.1.3.2.2.5.2.1.0
Method by which the CPE
acquires its IP address.
Read/Write
Integer
1=DHCP
atiMgmtSysMonitoringCpeStaticAddress
1.3.6.1.4.1.926.1.3.2.2.5.2.2.0
When the address source is
static, this is the IP address the
CPE will be assigned.
Read/Write
IP Address
0.0.0.0 (default)
atiMgmtSysMonitoringCpeStaticMask
1.3.6.1.4.1.926.1.3.2.2.5.2.3.0
static, this is the mask the
device will use to determine if
other devices are on the local
area network (LAN).
Read/Write
IP Address
0.0.0.0 (default)
atiMgmtSysMonitoringCpeStaticGateway
1.3.6.1.4.1.926.1.3.2.2.5.2.4.0
static, this is the IP address of
the gateway the device will use
for accessing devices not on the
local area network (LAN).
Read/Write
IP Address
0.0.0.0 (default)
2=Static
745-814-B8-001, Rev. A (08/2011)
61
10.0 Alpha MIB Parameters
10.1
Definitions and Settings, continued
Parameter
OID
Description
Access
Type
Value
COMMUNITY STRINGS
atiMgntSnmpCommunities
1.3.6.1.4.1.926.1.3.1.4.0
Object Identifier
atiMgmtSnmpCommGet
1.3.6.1.4.1.926.1.3.1.4.1.0
Default "Read" Community String
Read/Write
Octet String
AlphaGet (default
atiMgmtSnmpCommSet
1.3.6.1.4.1.926.1.3.1.4.2.0
Default "Read/Write" Community String
Read/Write
Octet String
AlphaSet (default)
Traps sent when an item in an alarm
state returns to normal.
Read/Write
Number of times a trap is to be sent/
repeated.
Read/Write
The number of minutes allowed to pass
without SNMP communications. On the
lapse of this many minutes the device
will reset. Setting this value to zero will
prevent timeout resets.
Read/Write
Access to DSM3 via Web Browser
Read/Write
SNMP TRAP
atiMgmtSnmpControls
1.3.6.1.4.1.926.1.3.1.5
atiMgmtSnmpTrapOnNormal
1.3.6.1.4.1.926.1.3.1.5.1.0
atiMgmtSnmpSendCount
atiMgmtSysSnmpTimeout
1.3.6.1.4.1.926.1.3.1.5.2.0
1.3.6.1.4.1.926.1.3.1.5.3.0
Object Identifier
Integer
1 = Disable
Integer
1 to 9
1 (Default)
Integer
0 to 65,000 (in minutes)
1440 (Default)
WEB SERVER ENABLE
atiMgmtSysHttpPrams
1.3.6.1.4.1.926.1.3.2.2.4
atiMgmtSysHttpEnabled
1.3.6.1.4.1.926.1.3.2.2.4.1.0
Object Identifier
Integer
1=Disable
2=Enable (default)
SIMPLE NETWORK TIME PROTOCOL
atiMgmtSysServers
1.3.6.1.4.1.926.1.3.2.3.0
atiMgmtSysServSntp
1.3.6.1.4.1.926.1.3.2.3.1.0
Object Identifier
IP Address of SNTP Server (Optional)
Read/Write
IP Address
0.0.0.0 (Default)
ENVIRONMENTAL MANAGER
atiMgmtSysTempMgr
1.3.6.1.4.1.926.1.3.2.4.0
atiMgmtSysTempCtrl
1.3.6.1.4.1.926.1.3.2.4.1.0
Object Identifier
Environmental Control
Read/Write
Integer
1=off (Default)
2=OnTimer
3=OnTemp
4=onTimerTemp
5=on
atiMgmtSysTempStatus
1.3.6.1.4.1.926.1.3.2.4.2.0
Environmental Control Feedback State
Read Only
Integer
1=Contact Open (default)
atiMgmtSysTempMode
1.3.6.1.4.1.926.1.3.2.4.3.0
Environmental Mode (Heat/Cool)
Read/Write
Integer
1=Heater (Default)
2=Contact Closed
2=Cooler
atiMgmtSysTempActiveState
1.3.6.1.4.1.926.1.3.2.4.4.0
Environmental Control Contact State
(Open/Closed)
Read/Write
Integer
1=Closed (Default)
atiMgmtSysTempTemperature
1.3.6.1.4.1.926.1.3.2.4.5.0
Environment Temperature
Read/Write
Integer
1..70ºC
atiMgmtSysTempHysteresis
1.3.6.1.4.1.926.1.3.2.4.6.0
Environmental Temperature Hysteresis
Read/Write
Integer
1..10ºC
atiMgmtSysTempTimer
1.3.6.1.4.1.926.1.3.2.4.7.0
Environmental Default Timer
Read/Write
Integer
0..1440 (30 Minute Default, 15
minute increments)
2=Open
atiMgmtSysTempCountdown
1.3.6.1.4.1.926.1.3.2.4.8.0
Environmental Timer Time Remaining
Read Only
Integer
0..1440 (in minutes)
atiMgmtSysTempStatusInvert
1.3.6.1.4.1.926.1.3.2.4.9.0
State Inverted to match the type of relay
operation on the heater mat controller
Read/Write
Integer
1=No invert (Default)
2=Invert
PHONE HOME MANAGER
atiMgmtSysPhoneHomeIp
1.3.6.1.4.1.926.1.3.2.5
atiMgmtSysPhoneHomeIp
1.3.6.1.4.1.926.1.3.2.5.1.0
Address for the Phone Home Frame
Read/Write
IP Address
Object Identifier
0.0.0.0
atiMgmtSysPhoneHomeForce
1.3.6.1.4.1.926.1.3.2.5.2.0
Forces one Phone Home message
regardless of timers
Read/Write
Integer
1=No Operation (default)
atiMgmtSysPhoneHomeTimer
1.3.6.1.4.1.926.1.3.2.5.3.0
Time since last frame transmitted, zero
means never transmitted
Read Only
Time Ticks
2=Force
62
745-814-B8-001, Rev. A (08/2011)
10.0 Alpha MIB Parameters, continued
10.1
Parameter
OID
Description
Access
Type
Value
1.3.6.1.4.1.926.1.3.2.6.1.0
Determines when tamper is active
Read/Write
Integer
1=Alarm On Open (Default)
GENERAL CONTROLS
atiMgmtSysTamperPolarity
2=Alarm On Close
atiMgmtSysAlphaBusSize
1.3.6.1.4.1.926.1.3.2.6.2.0
Internal microprocessor communications bus size.
Alpha XM2 series power supplies use 9 bit. Alpha
GMX and VMX series supplies use 8 bit
Read/Write
Integer
1=9 Bit (Default)
2=8 Bit
atiMgmtSysGnrlInfoConfigs
1.3.6.1.4.1.926.1.3.2.7.1
Object Identifier
atiMgmtSysGnrlInfoConfigsMain
1.3.6.1.4.1.926.1.3.2.7.1.1.0
An ASCII string programmed into the main board
non-volatile memory.
Read Only
Octet String
Product number, configuration
number serial number, etc.
atiMgmtSysGnrlInfoConfigsDaughter
1.3.6.1.4.1.926.1.3.2.7.1.2.0
An ASCII string programmed into the C/D battery
circuitry (DSM3x only).
Read Only
Octet String
Product number, configuration
number serial number, etc.
atiMgmtSysGnrlInfoConfigsBase
1.3.6.1.4.1.926.1.3.2.7.1.3.0
An ASCII string describing the base configuration
of the device.
Read Only
Octet String
i.e. DSM3, DSM3x, DPM, etc.
Indicates if the LAP surge suppressor is being
monitored on the external ENV connector. This
parameter must be manually set when an LAP is
installed, the LAP is not automatically detected.
Read/Write
Current state of the LAP device
Read Only
LAP SURGE SUPPRESSOR
atiMgmtSysLAP
1.3.6.1.4.1.926.1.3.2.8
atiMgmtSysLAPInstalled
1.3.6.1.4.1.926.1.3.2.8.1.0
atiMgmtSysLAPState
1.3.6.1.4.1.926.1.3.2.8.2.0
Object Identifier
Integer
1=Not installed (Default)
2=Installed
Integer
1: notInstalled(1)
2: ok(2)
3: acNotPresent(3)
4: replaceLap(4)
5: LAP fault or wiring error(5)
PLATFORMS
atiProductPlatforms
1.3.6.1.4.1.926.1.4
atiBroadbandUPS
1.3.6.1.4.1.926.1.4.1
Object Identifier
Object Identifier
atiBBSysView
1.3.6.1.4.1.926.1.4.1.1
Object Identifier
atiBBSysViewSelects
1.3.6.1.4.1.926.1.4.1.1.1
atiBBSysViewSelfTestControl
1.3.6.1.4.1.926.1.4.1.1.1.1.0
Object Identifier
Starts/Stops a system self-test.
Read/Write
Integer
1=Stop
2=Start
atiBBSysViewSelfTestInhibit
atiBBSysViewSystemControlMgr
atiBBSysViewFactoryDefaults
745-814-B8-001, Rev. A (08/2011)
1.3.6.1.4.1.926.1.4.1.1.1.2.0
1.3.6.1.4.1.926.1.4.1.1.1.3.0
1.3.6.1.4.1.926.1.4.1.1.1.4.0
System self-test is prevented. On reset, the DSM
gets this value from the master XM2 (in a system
with more than one power supply).
Read/Write
If the System Control Manager is running, the
Small System Controller/Administrator (SSC or
SSA) is running and there is coordination between
the power supplies for charging, testing, etc. The
value of this item is stored in non-volatile memory.
Read/Write
Will set all parameters back to the factory default
value.
Read/Write
Integer
1=Normal (Default)
2=Inhibited
Integer
1=Running
2=Disabled
Integer
1=Normal
2=Reset
63
10.0 MIB Parameters
10.1
Parameter
OID
Description
Access
Indicates if any of the items monitored are in a major
alarm state.
Read Only
Indicates if any of the items monitored are in a minor
alarm state.
Read Only
If any of the items being monitored indicate that
self-test failed, this item indicates a failure.
Read Only
If any of the devices being monitored indicate a
temp probe failure or absence, this item will alarm.
Read Only
If ALL the items being monitored indicate no AC, this
item will alarm.
Read Only
Type
Value
SYSTEM ALARMS
atiBBSysViewAlarms
1.3.6.1.4.1.926.1.4.1.1.2
atiBBSysViewMajorAlarm
1.3.6.1.4.1.926.1.4.1.1.2.1.0
atiBBSysViewMinorAlarm
1.3.6.1.4.1.926.1.4.1.1.2.2.0
atiBBSysViewSelfTestResult
1.3.6.1.4.1.926.1.4.1.1.2.3.0
atiBBSysViewTempProbeStatus
1.3.6.1.4.1.926.1.4.1.1.2.4.0
atiBBSysViewInputStatus
1.3.6.1.4.1.926.1.4.1.1.2.5.0
Object Identifier
Integer
1=OK
2=Alarm
Integer
1=OK
2=Alarm
Integer
1=OK
2=Fail
Integer
1=OK
2=Missing
Integer
1=OK
2=No AC Present
SCALARS
atiBBSysViewScalars
1.3.6.1.4.1.926.1.4.1.1.3
atiBBSysViewInputVoltage
1.3.6.1.4.1.926.1.4.1.1.3.1.0
Power supply input voltage.
Read Only
Integer
Object Identifier
atiBBSysViewInputFrequency
1.3.6.1.4.1.926.1.4.1.1.3.2.0
Power supply input line frequency.
Read Only
Integer
atiBBSysViewInputCurrent
1.3.6.1.4.1.926.1.4.1.1.3.3.0
Power supply input current.
Read Only
Integer
atiBBSysViewBatteryVoltage
1.3.6.1.4.1.926.1.4.1.1.3.4.0
Battery voltage.
Read Only
Integer
atiBBSysViewBatteryTemperature
1.3.6.1.4.1.926.1.4.1.1.3.5.0
Battery temperature (Degrees C).
Read Only
Integer
atiBBSysViewChargerCurrent
1.3.6.1.4.1.926.1.4.1.1.3.6.0
Sum of charging current from all power supplies.
Read Only
Integer
atiBBSysViewChargerVoltsFloat
1.3.6.1.4.1.926.1.4.1.1.3.7.0
Battery charger float voltage.
Read/Write
Integer
atiBBSysViewChargerVoltsEqualize
1.3.6.1.4.1.926.1.4.1.1.3.8.0
Battery charger equalization voltage.
Read/Write
Integer
atiBBSysViewChargerVoltsTemperatureComp
1.3.6.1.4.1.926.1.4.1.1.3.9.0
Battery charger temperature compensation
Read/Write
Integer
(0 to 5mV/Cell/°C)..
atiBBSysViewBatteryCapacity
1.3.6.1.4.1.926.1.4.1.1.3.10.0
Battery string capacity (Amp hours).
Read/Write
Integer
1.3.6.1.4.1.926.1.2.1.1.1.5.14.0.11
Controls the ability to detect and report 6 Volt
batteries.
Read/Write
Integer
DETECT 6V BATTS
atiCibDiscTable
0 = default
1 = Detect 6 Volt
Batteries
Broadcom MIBS:
Parameter
OID
Description
Access
Type
Value
HTTP Management MIB
64
httpMgmt
1.3.6.1.4.1.4413.2.2.2.1.1.3
httpAdminId
1.3.6.1.4.1.4413.2.2.2.1.1.3.1.0
Controls and reflects the user name for admin level HTTP
priveleges.
Read/Write
Octet String
Object Identifier
Alpha (Default)
httpAdminPassword
1.3.6.1.4.1.4413.2.2.2.1.1.3.2.0
Controls and reflects the password for admin level HTTP
priveleges.
Read/Write
Octet String
AlphaSet (Default)
httpUserId
1.3.6.1.4.1.4413.2.2.2.1.1.3.3.0
Controls and reflects the user name for user level HTTP
priveleges.
Read/Write
Octet String
Alpha (Default)
httpUserPassword
1.3.6.1.4.1.4413.2.2.2.1.1.3.4.0
Controls and reflects the password for user level HTTP
priveleges.
Read/Write
Octet String
AlphaGet (Default)
745-814-B8-001, Rev. A (08/2011)
11.0 Specifications
Specifications for AlphaNet DSM3 Family
DSM3x
Power Supply Models Supported: XM2-HP, XM2, GMX, VMX
Battery Monitoring:
Power System Management:
Management Protocol:
Up to four strings of 36 or 48V
batteries (6V batts configurable up to
two strings)
Up to five power supplies and an
AlphaGen generator are managed
from a single DSM3 Series including
coordinated battery charging, system
test and aggregated alarms
DSM3
DPM
XM2-HP, XM2, GMX, VMX
XM2-300HP
Up to two strings of 36 or 48V
batteries (6V batts configurable
up to two strings)
One 12V battery (or two if
AlphaCells
N/A
N/A
Standard ANSI/SCTE-HMS MIBs support basic power supply monitoring. Advanced diagnostics with
battery and power module analytics available via secure SNMP
Advanced Diagnostics1
Intelligent Power Supply
Interface:
Battery State of Health:
Power Inverter State of Health:
Power supply user interface displays advanced diagnostics including: DOCSIS modem upstream and
downstream RF levels, IP address assigned by network DHCP server, MAC address and firmware
versions, individual battery voltages to verify correct wire harness installation
Power supply internal analytic diagnostics report when batteries should be serviced.
Reported Status:
Batteries OK
Battery Thermal Warning – PM Visit Recommended
Battery Thermal Alarm – Service Required
Power supply internal diagnostics report if the power inverter requires service.
Reported Values: Inverter OK, Replace Inverter
Hardware
RF Cable Interface:
F-connector, female, 75 Ohm, connector angle better accommodates coax bend radius when installed in
some enclosures
Local Interface:
RJ-45, Ethernet, 10/100
LED Indicators:
Ready/Alarm, Upstream registration, Downstream lock, AlphaBus activity, RF level, Link, CPE traffic, Battery
Sense harness correctly connected
I/O Control (DSM3x Series and
DPM Only):
6-pin Molex: Digital input, Digital output, 5V, Common
AlphaBus:
RJ-11 offset tab: Multiple-power supply and AlphaGen communications
Battery Monitoring:
8-pin Molex battery string A/B and
8-pin Molex battery string C/D.
Tamper:
NO or NC, software configurable, reads enclosure door magnetic switch
8-pin Molex battery string A/B
N/A
Environment
Operating Temperature:
-40 to 65°C / -40 to 149°F
Storage Temperature:
-40 to 85°C / -40 to 185°F
Humidity:
10 to 90% non-condensing
Regulatory Compliance:
FCC Part 15 Class A
EN 50083-2:2006 EMC requirements for CATV equipment
EN 62040-2:2006 Uninterruptable power supply EMC requirements, Category C2
Surge: IEEE 587, Category B3
RoHS: Directive 2002/95/EC
1
Advanced diagnostics are available through Alpha Certified network monitoring systems
Network Communications
DOCSIS (RF) Port Protocols:
IP, UDP, TCP, DHCP, TFTP, SNMPv1,SNMPv2c, HTTP, SNTP
Ethernet Port:
Local Mode: HTTP Web interface for local on-site diagnosis.
CPE Mode: DOCSIS Cable modem Ethernet CPE functionality
MIBs:
Power supply (ANSI/SCTE 38-4)
Other SCTE-HMS MIBs as defined by the SCTE for power supply and generator status monitoring
Alpha proprietary advanced UPS diagnostics
745-814-B8-001, Rev. A (08/2011)
65
11.0 Specifications
Specifications for AlphaNet DSM3 Family
DSM3x
DSM3
DPM
Power Supply Monitored Parameters
Major Alarm:
Aggregate alarm consisting of: test fail, battery fail, line isolation alarm, output overload, inverter,
over-temperature, N+1 active, fuse fail
Minor Alarm:
Aggregate alarm consisting of: temperature probe error, AC line loss, N+1 error
Input Voltage:
Reported from power supply V(in) measurement
Output Voltage:
Reported from power supply V(out) measurement
Output Current:
0 to 25A standard on port 1
Ports 2-4 require power supply option
Output Power:
Calculated, reported in AC Watts
Dual outputs do not exceed 300 Watts
combined 3.5 Amps at 90 Vac output
voltage, 5 Amps at 60 Vac output voltage
UPS Status:
AC Line, Standby, Test in progress, Test alarm
Enclosure Door:
Open or Closed
Battery Voltage:
Individual battery voltage,
Individual battery voltage, up to
up to two strings of 3 or
four strings of 3 or 4 batteries
4 batteries (maximum 8
(maximum 16 batteries),
batteries), ±100mV per
±100mV per battery.
battery.
Battery Temperature:
Reported from power supply battery Remote Temperature Sensor (RTS)
Remote Test Control:
Start/Stop power supply test cycle
Individual battery voltage
Generator Monitored Parameters (DSM3x Only)
Status:
Generator Off, Running, Alarm
Generator Alarm:
Aggregate alarm consisting of: low oil pressure, engine over-temp, engine over-speed, crank limit,
over voltage, low fuel, water intrusion, pad shear, gas hazard, test fail
Gas Hazard:
OK, Alarm
Water Intrusion:
OK, Alarm
Pad Shear:
OK, Alarm
Enclosure Door:
Open, Alarm
Ignition Battery Voltage:
±100mV
Enclosure Temperature:
±2°C
Low Fuel:
OK, Alarm
Remote Test Control:
Start / Stop generator test cycle
Cable Modem
Compliance:
DOCSIS 1.1 and 2.0
EuroDOCSIS 2.0
Transmit Frequency Range:
5 to 42MHz
5 to 65 Mhz
Receive Center Frequency Range:
91 to 857MHz
112 to 858 Mhz
Output Power Range:
TDMA:
+8 to +54 dBmV (32QAM, 64QAM)
+8 to +55 dBmV (8QAM, 16QAM)
+8 to +58 dBmV (QPSK)
S-CDMA:
+8 to +53 dBmV (All modulations of S-CDMA)
TDMA:
+68 to +114 dBuV (32QAM, 64QAM)
+68 to +115 dBuV (8QAM, 16QAM)
+68 to +118 dBuV (QPSK)
S-CDMA:
+68 to +113 dBuV (All modulations of S-CDMA)
Input Signal Range:
-15 to 15dBmV
64QAM: 43 to 73 dBuV
256QAM: 47 to 77 dBuV
Channel Bandwidth:
6MHz
8Mhz
Additional Equipment
66
XP-BSC-3-6:
Wire Kit, Battery Sense, 1x36V, 6'
XP-BSC-6-6:
XP-BSC-4-6:
Surge Protector
(Alpha p/n 162-028-10):
Female/Female connector configuration, “F” type connector with integral ground block. Required for
all installations
745-814-B8-001, Rev. A (08/2011)
12.0 Glossary
Acronym Definitions
ANSI:
American National Standards Institute
BER:
Basic Encoding Rules
CM:
Cable Modem
CMTS:
Cable Modem Termination System
CPE:
Customer Premises Equipment
DHCP:
Dynamic Host Configuration Protocol
DOCSIS:
Data Over Cable Service Interface Specification
EMS:
Element Management System
HMS:
Hybrid Management Sublayer
IT:
Information Technology
MAC:
Media Access Control
MIB:
Management Information Base
NMS:
Network Management System
QoS:
Quality of Service
RTS:
Remote Temperature Sensor
SCTE:
Society of Cable Telecommunications Engineers
SI:
Serial Interface
SNMP:
Simple Network Management Protocol
SNTP:
Simple Network Time Protocol
TFTP:
Trivial File Transfer Protocol
TOD:
Time of Day
UDP:
User Datagram Protocol
VoIP:
Voice over Internet Protocol
745-814-B8-001, Rev. A (08/2011)
67
13.0 Dual IP Mode (Addendum)
13.1
Overview
The DSM3 Series can operate in either Single (default) or Dual IP Mode. In Single IP mode, data from
both the cable modem and power supply are accessed and managed through the modem’s IP address on
the secure private modem network. In Dual IP mode, the transponder acts like a CPE device to the cable
modem and registers a second IP address on the public CPE network.
The following table lists some of the common characteristics of the DSM3 Single IP and Dual IP
configurations:
Single IP
Dual IP
Network
All data from both the cable modem and power
supply are accessed and managed through
the modem’s IP address on the secure private
modem network.
The transponder acts like a CPE device to the cable
modem and registers a second IP address on the public
CPE network.
Data Access
The Network Management System requires
access to the same private modem network.
Dual IP mode allows the power supply data to be
accessed and managed from anywhere within the
public (CPE) network.
Security
Communication with the transponder is limited
to the private LAN network, and is very secure.
Since the transponder is a CPE on the public network,
access may be less secure.
IP Addresses
Where the IP address pool is limited, there is
no need to issue the transponder a CPE IP
address. Only one (1) IP Address is required for
the cable modem of the DSM3.
The CPE requires its own IP address, which may be
in short supply. A total of two (2) IP addresses are
required, one for the cable modem and one for the
transponder.
Data Management
Access to the transponder is limited to the
private LAN network making data management
less versatile, especially for field personnel.
The transponder is accessible on the public (CPE)
network. This makes data management more versatile
for field personnel.
Table 13-1, Single IP Mode versus Dual IP Mode
One CM IP address only accessible on the private (LAN)
network with access to both CM and transponder data.
One CM IP address, CM and transponder data;
accessible on the private (LAN) network.
DSM
DSM
Cable Modem
Cable Modem
Transponder (CPE)
Transponder
MIB Tables
MIB Tables
One CPE IP address, transponder data only;
accessible on the public (CPE) network.
Fig. 13-1, Simplified Block Diagram
Single IP Mode
68
Fig 13-2, Simplified Block Diagram
Dual IP Mode
745-814-B8-001, Rev. A (08/2011)
13.0
Dual IP Mode (Addendum), continued
13.2
Web Comparison, Single IP Mode/Dual IP mode
To easily determine the configuration of the transponder when viewing it on its web page, check the
Configuration Line as well as the entries for the CM and CPE addresses. A single IP transponder will
display a CM MAC address only, while a dual IP transponder will also indicate a CPE address.
Indicates 1 IP address:
"Single IP" Status Monitor
Displays CM MAC address only
®
General
HMS Alarms
Advanced Configuration
APPS
History
Print Print
Communications
Configuration
SysUpTime
Firmware Version
1IP US
7 days 11H:13m:17s
4.4.6.0_02.00_NA
MAC Address
00:90:EA:00:30:84
IP Address
CM Tx (dBmV)
192.168.1.124
42.0
CM Rx (dBmV)
3.2
SNR (RxMER)
44.2
CM
41.0
+50
0
55
60
3.2
-20
-15
-10
15
10
20
SET
System Name
Alpha
System Location
Bellingham
System Contact
John Doe
Common Logical ID
DSM3
Fig. 13-3, Single IP DSM3 Series Web Page
(partial page only; data values shown for illustration purposes only)
Indicates 2 IP addresses:
"Dual IP" Status Monitor
Displays CM and CPE addresses only
®
General
Alarms
Advanced
Configuration
General HMSHMS
Alarms
Advanced
Configuration
APPS
PrintPrint
History
Communications
Configuration
SysUpTime
Firmware Version
2IP US
7 days 11H:13m:17s
4.4.6.0_02.00_NA
CM
CPE Transponder
MAC Address
00:90:EA:00:30:84
00:90:EA:00:30:85
IP Address
CM Tx (dBmV)
192.168.1.124
42.0
192.168.1.120
CM Rx (dBmV)
3.2
SNR (RxMER)
44.2
41.0
+50
0
55
60
3.2
-20
-15
-10
10
15
20
SET
System Name
Alpha
System Location
Bellingham
System Contact
John Doe
Common Logical ID
DSM3
Fig. 13-4, Dual IP DSM3 Series Web Page
(partial page only; data values shown for illustration purposes only)
745-814-B8-001, Rev. A (08/2011)
69
13.0
13.3
Configuring Dual IP Mode
To switch the DSM3 Series transponder from Single to Dual IP Mode the atiMgmtSnmpSnmpCPEAccess
parameter of the Alpha MIB will need to be enabled. The Dual IP enable setting can be set through the
DOCSIS Configuration file, the DSM3 Setup File (atidoc03.cfg) or remotely using SNMP by setting the
following Alpha MIB:
MIB Parameter
Object ID
Description
Value
atiMgmtSnmpSnmpCPEAccess
1.3.6.1.4.1.926.1.3.1.3.6.0
Enables/Disables the
CPE Interface
1=Disabled (Single IP)
2=Enabled (Dual IP)
Table 13-2, Enabling Dual IP mode
The CPE Transponder IP can be assigned its IP, Subnet Mask and Gateway Addresses either via DHCP
(default) or manually, either through the web page or via the below SNMP settings:
NOTE:
After configuring the Static settings the transponder must be reset in order for the settings to take effect.
MIB Parameter
Object ID
Description
Value
atiMgmtSysMonitoringCpeStaticMode
1.3.6.1.4.1.926.1.3.2.2.5.2.1.0
Method by which the CPE
acquires its IP address.
1=DHCP
2=Static
atiMgmtSysMonitoringCpeStaticAddress
1.3.6.1.4.1.926.1.3.2.2.5.2.2.0
When the IP address is static,
this is the IP address to which
the CPE will respond.
0.0.0.0 (default)
atiMgmtSysMonitoringCpeStaticMask
1.3.6.1.4.1.926.1.3.2.2.5.2.3.0
When the CPE IP address is
static, this is the subnet mask.
0.0.0.0 (default)
atiMgmtSysMonitoringCpeStaticGateway
1.3.6.1.4.1.926.1.3.2.2.5.2.4.0
When the IP address is static,
this is the IP address of the
gateway.
0.0.0.0 (default)
Table 13-3, CPE Transponder IP Settings
70
745-814-B8-001, Rev. A (08/2011)
13.0
13.3
Assigning Static IP Address via DSM3 Web Server
To change the IP address allocation option from “DHCP” to “Static” via the Web Server, refer to the
following:
1. Connect to DSM via Web browser per the procedure in section 4.0.
2. Move mouse pointer to the “Advanced Settings” in the menu bar of the DSM3 Web page and click
on the “Communications” selection in the pop-up menu.
3. Select the “Static” option in the CPE Transponder column of the page. Refer to figure 13-3. When
prompted for user ID and password, enter "Alpha" and "AlphaSet".
4. Enter the desired IP address, Subnet Mask and Gateway in the provided data fields.
5. Click the “Set” button to update the transponder with the new values.
6. Confirm the new Static IP Address is listed under the CPE Transponder column of the “General”
page. Refer to figure Section 13.6.
General HMS
HMS
Alarms
Advanced
Confi
guration
General
Alarms
Advanced
Confi
guration
APPS
HISTORY
Print
Print
ADVANCED COMMUNICATIONS
RESET TRANSPONDER
NETWORK PROVISIONING
CM
CPE Transponder
MAC
00:90:EA:00:30:82
00:90:EA:00:30:83
DHCP/Static
DCHP
Status
Operational
SysUpTime
1 day 22h:29m:52s
DCHP
Static
IP
192.168.1.140
192.168.1.150
Subnet Mask
255.255.255.0
255.255.255.0
SET
192.168.1.1
Gateway
192.168.1.1
Lease Duration
D: 00 H: 01: M: 00 S: 00
Lease Expires
Configuration File
atidoc03.cfg
Config Download Timer (Hours)
24
Fig. 13-5, Dual IP Configuration Settings on Communications page of DSM3 Web Server
®
GeneralHMSHMS
Alarms
Advanced
Configuration
General
Alarms
Advanced
Configuration
APPS
HISTORY
Print Print
Communications
Configuration
SysUpTime
Firmware Version
2IP US
7 days 11H:13m:17s
4.4.6.0_02.00_NA
CM
CPE Transponder
MAC Address
00:90:EA:00:30:82
00:90:EA:00:30:83
IP Address
CM Tx (dBmV)
192.168.1.124
42.0
192.168.1.150
CM Rx (dBmV)
3.2
41.0
+50
0
-20
SNR (RxMER)
55
60
3.2
-15
-10
10
15
20
44.2
System Name
Alpha
System Location
Bellingham
System Contact
John Doe
Common Logical ID
DSM3
SET
Fig. 13-6, Dual IP Parameters on the General page of DSM3 Web Server
745-814-B8-001, Rev. A (08/2011)
71
13.0
13.3
Assigning Static IP Address via DSM3 Web Server
13.3.1 atidoc03.cfg in Dual-IP Mode
NOTE:
Refer section 3.2.4 for details on using the atidoc03.cfg file to propagate custom settings to
field-deployed DSM3 Series transponders.
In Dual-IP mode, the DSM3 Series will first attempt to download the proprietary configuration
file atidoc03.cfg through the CPE’s interface from a TFTP server on the CPE network. In many
networks, the TFTP server is blocked or disabled, so the DSM3 Series also has provisions to
download this file through the Cable Modem interface from the modem’s provisioning server if
necessary. The filename and TFTP server location may also be specified through special tags in
the DHCP Offer, refer to section 13.3.3 for details. Similiar to Single-IP mode, any DSM3 Series
proprietary SNMP MIB setting may be placed in the modem’s DOCSIS configuration file which
would eliminate the need for atidoc03.cfg.
13.3.2 Changing Default atidoc03.cfg Download Settings in Dual-IP Mode
The following table explains the download options available for the atidoc03.cfg file in Dual-IP
mode. The ‘Download Interface’ indicates the network from which the DSM3 series will attempt
to download atidoc03.cfg, either the CPE network or the more secure cable modem management
network.
Search Download
Order
Interface
Parameter
Comments
Value
atiMgmtSysDownloadConfigAddress
OID 1.3.6.1.4.1.926.1.3.2.1.10.0
Overrides Default Location
0.0.0.0 (Default)
1
CPE
DHCP Server IP
Server or Relay Agent Address
from DHCP lease (No Change
Necessary)
As Set
2
CPE
DHCP Option 54 Server IP
Server or Relay Agent Address
from DHCP lease
As Set
3
CPE
DHCP Tags
See Below section 13.3.3
As Set
4
CPE
docsDevServerConfigTftpAddress
1.3.6.1.2.1.69.1.4.11.0
Automatically set in modem
CM's TFTP Server
Address
5
CM
1.3.6.1.2.1.69.1.3.7.0
Set via DOCSIS configuration file
As Set
6
CM
Software Upgrade Server
Set via DOCSIS configuration file
As Set
7
CM
13.3.3 Specifying atidoc03.cfg name and location via DHCP Tags
In the User-defined area of the DHCP Tags, above option 192, the TRANSPONDER will look for
the following value:
Tag: [Insert Unique Tag Name, e.g. ‘ati-tag’]
Value: aticonfig
In the Tag value immediately following will be the value for the TFTP server to use:
Tag: [Insert Unique Tag Name, e.g. ‘ati-ip’]
Value: IP address of TFTP server (i.e. 192.168.1.51)
Immediately following will be the value for the config filename
Tag: [Insert Unique Tag Name, e.g. ‘ati-name’]
Value: =atidoc03.cfg (an equal sign needs to be in front of the filename for the DHCP server
to recognize this as a valid entry.)
72
745-814-B8-001, Rev. A (08/2011)
13.0
13.4
Dual IP SNMP Community Strings
The transponder community strings used for the CPE Transponder in Dual IP mode can be configured
by the operator. The default transponder read-only community string is AlphaGet. The default read-write
community string is AlphaSet. These settings can be configured with the DOCSIS Configuration File, the
DSM3 Setup File (aitdoc03.cfg) or remotely using SNMP by including the parameters below:
NOTE:
These community strings are only applicable for CPE access in Dual IP mode. CM access in both Single
IP and Dual IP modes use standard DOCSIS community strings set through the modem configuration file's
docsDevNmAccessTable. See Section 3.2.1.
MIB Parameter
Object ID
Description
Value
atiMgmtSnmpCommGet
1.3.6.1.4.1.926.1.3.1.4.1.0
Read Community String
AlphaGet (default)[desired
value]
atiMgmtSnmpCommSet
1.3.6.1.4.1.926.1.3.1.4.2.0
Read/Write Community String
AlphaSet (default)[desired
value]
Table 13-4, Data Access Key Parameters
13.5
Security in Dual IP Mode
In Dual IP Mode, additional SNMP security to the DSM3 Series proprietary MIBs is required since the
transponder and power supply data is exposed on the CPE network, which may be more vulnerable to
packet sniffing and community string deciphering than on the secure cable modem network.
There are two methods of providing SNMP Security in Dual IP Mode: the Data Access Key (Default), and
the Secure Access List.
Method 1: Dual IP Security Using the Data Access Key
In Dual IP Mode atiMgmtSnmpAlphaSetAccess is the only SNMP parameter within the Alpha
proprietary MIB with SNMP-write access on the CPE network by default. When this parameter is
set to the value of the parameter atiMgmtSnmpAlphaSetKey, the data access key, SNMP read/write
access is granted to all parameters in the Alpha MIB tree with read/write attributes. When this access
is granted, the value of atiMgmtSnmpCPESetEnabled is automatically changed to "2" (enabled). After
the operator is finished setting the SNMP variables, SNMP write access can be disabled by setting the
atiMgmtSnmpCPESetEnabled to "1" or by setting atiMgmtSnmpAlphaSetAccess to any value other than
the data access key or by performing a reset to the DSM3 Series.
The data access key parameters can be changed from the default values through the DOCSIS
Configuration File, the DSM3 Series Setup File (atidoc03.cfg) or remotely using SNMP by including the
following Alpha MIB parameters:
MIB Parameter
Object ID
Description
Value
atiMgmtSnmpAlphaSetAccess
1.3.6.1.4.1.926.1.3.1.3.3.0
Set to Access Key
Set to match the value of
1.3.6.1.4.1.926.1.3.1.3.4.0
Data Access Key (Dual IP)
CIBSET (default)
atiMgmtSnmpCPESetEnabled
1.3.6.1.4.1.926.1.3.1.3.5.0
Corresponds to whether
or not the action taken on
atiMgmtSnmpAlphaSetKey was
successful. Once enabled, writing
1 to this variable will disable CPE
sets.
1 = Disabled (False)
2 = Enabled (True)
Table 13-5, Data Access Key Parameters
745-814-B8-001, Rev. A (08/2011)
73
13.0
13.5
Security in Dual IP Mode, continued
Method 2: Dual IP Security Using the Secure Access List
The DSM3 provides an alternative method of providing additional SNMP security in Dual IP by limiting access
to the transponder’s CPE address. The Secure Access List method limits remote SNMP access to four IP
addresses. Only the IP addresses listed in the SNMP Access Table are able to read or write to the Alpha MIB
parameters from the public (CPE) network. This method overrides the default "Data Access Key" method.
The IP address entries in the SNMP Access Table can be set through the DOCSIS Configuration File, the DSM3
Setup File (atidoc03.cfg) or remotely using SNMP by including the following Alpha MIB parameters:
MIB Parameter
Object ID
Description
Value
atiMgmtSnmpAccessTable
1.3.6.1.4.1.926.1.3.1.2
Table of SNMP
Access Addresses
Object identifier
1.3.6.1.4.1.926.1.3.1.2.1.2.1
SNMP access IP Address #1
0.0.0.0 (Default)
1.3.6.1.4.1.926.1.3.1.2.1.2.2
0.0.0.0 (Default)
1.3.6.1.4.1.926.1.3.1.2.1.2.3
0.0.0.0 (Default)
1.3.6.1.4.1.926.1.3.1.2.1.2.4
0.0.0.0 (Default)
Table 13-6, Secure Access Table Parameters
74
745-814-B8-001, Rev. A (08/2011)
this page intentionally blank
Alpha Technologies Inc.
3767 Alpha Way
Bellingham, WA 98226
United States
Tel: +1 360 647 2360
Fax: +1 360 671 4936
Alpha Energy
1628 W Williams Drive
Phoenix, AZ 85027
United States
Tel: +1 623 251 3000
Fax: +1 623 249 7833
Alpha Technologies Europe Ltd.
Twyford House Thorley
Bishop’s Stortford
Hertfordshire, CM22 7PA
United Kingdom
Tel: +44 1279 501110
Fax: +44 1279 659870
Alpha Technologies
Suite 1903, 19/F., Tower 1
33 Canton Road, Tsim Sha Tsui
China Hong Kong City, Kowloon
Hong Kong
Phone: +852 2736 8663
Fax: +852 2199 7988
Alpha Technologies Ltd.
7700 Riverfront Gate
Burnaby, BC V5J 5M4
Canada
Tel: +1 604 436 5900
Fax: +1 604 436 1233
Toll Free: +1 800 667 8743
Alpha Industrial Power Inc.
1075 Satellite Blvd NW,
Suite 400
Suwanee, GA 30024
United States
Tel: +1 678 475 3995
Fax: +1 678 584 9259
Alpha Technologies GmbH
Hansastrasse 8
D-91126
Schwabach, Germany
Tel: +49 9122 79889 0
Fax: +49 9122 79889 21
Technologies Argus
First de Mexico
Anatole France Num. 17
Colonia Polanco
11560, México D.F.
Tel: +52 55 5280 6990
Alphatec Ltd.
339 St. Andrews St.
Suite 101 Andrea Chambers
P.O. Box 56468
3307 Limassol, Cyprus
Tel: +357 25 375 675
Fax: +357 25 359 595
Alpha TEK ooo
Khokhlovskiy Pereulok 16
Stroenie 1, Office 403
Moscow, 109028
Russia
Tel: +7 495 916 1854
Fax: +7 495 916 1349
Alpha Innovations Brasil
Avenida Ibirapuera,
2120 – Cj 76
Moema - 04028-001
Santos SP, Brazil
Tel: +55 11 2476 0150
Fax: +55 11 2476 0150
Alphatec Baltic
S. Konarskio Street 49-201
Vilnius, LT-03123
Lithuania
Tel: +370 5 210 5291
Fax: +370 5 210 5292
Visit us at www.alpha.com
Due to continuing product development, Alpha Technologies reserves the right to change specifications without notice.
Copyright © 2011 Alpha Technologies. All Rights Reserved. Alpha® is a registered trademark of Alpha Technologies.
745-814-B8-001 Rev. A (08/2011)

AlphaNet DSM3 Series DOCSIS® Status Monitor

Transcription

Similar documents

Garrett SuperWand - Garrett Metal Detectors

MiniPulse - Electrostatica

LIFEPAK 500 Maintenance Checklist

Light Options – There are 3 dual LED strips in the

Nucsafe - Southern Scientific

Check Out Andtech`s 2009 Newsletter

San Bernardino Municipal Code 8.81.110

Press Pack

Charging Lipo Batteries with the Hextronik HX 8080 Charger