View the Installation Instructions

Transcription

INSTALLATION
INSTRUCTIONS
PARTS LIST
Accessory
Application
BACK-UP SENSORS
P/N 08V67-SJC-101
2012 RIDGELINE
Publications No.
AII 12006
Issue Date
NOV 2011
3
Wire ties with small clips
(2 Not used)
2
Wire ties with large clips
Back-up sensor harness
Control unit
Flange bolt
Buzzer
Buzzer bracket
Fuse label
Control unit bracket
5
EPT sealers
Switch
40 Wire ties
(7 Not used)
Ground bolt
9
Small wire ties
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 46956 (1111)
08V67-SJC-1002-91
1 of 28
2
Corner sensors
2
Center sensors
2
Retainer clips
2
Well nuts
Corrugated tube
Flange nut
3
Cushion tapes
(Some may not be used)
Washer-screw, 6 x 12 mm
Accessory User’s Information Manual
6
Tailgate switch
Oval grommets
Round grommet
7
Clips
Tailgate switch bracket
Template
4
Washer-screws, 4 x 14 mm
2 of 28
AII 46956 (1111)
TOOLS AND SUPPLIES REQUIRED
INSTALLATION
Phillips screwdriver
Customer Information: The information in this
installation instruction is intended for use only by skilled
technicians who have the proper tools, equipment, and
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
Small flat-tip screwdriver
10 mm Combination wrench
10 mm and 14 mm Sockets
Pushpin
Ratchet
3 mm and 8 mm Drill bits
1.
Make sure you have the anti-theft code for the radio,
then write down the radio station presets.
File
2.
Disconnect the negative cable from the battery.
Diagonal cutters
3.
Remove the left dashboard side cover (seven clips).
Eye protection (face shield, safety goggles, etc.)
Tape measure
Isopropyl alcohol
Shop towel
20 mm and 26 mm Hole saws
Drill
Utility Knife
7 CLIPS
Scissors
T-30, T-40, and T-50 Torx drivers
Insulation tape
Center punch
4 mm Hex wrench
Torque wrench
Touch-up paint
LEFT DASHBOARD
SIDE COVER
Blanket
Adhesive tape
7D2002AX
Plastic trim tool T/N SILTRIMTL10
Illustration of the Back-Up Sensors Installed on the
Vehicle
SWITCH
BUZZER
TAILGATE
SWITCH
BACK-UP
SENSOR
HARNESS
CONTROL
UNIT
CORNER
SENSOR
CORNER
SENSOR
CENTER
SENSOR
7D2001AX
AII 46956 (1111)
3 of 28
4.
Remove the driver’s dashboard lower cover (one
self-tapping screw, nine clips, unplug the vehicle
connectors, and the vehicle tube).
SELF-TAPPING
SCREW
6.
Remove the passenger’s console side trim (two clips
and retaining tab).
VEHICLE
CONNECTORS
VEHICLE
TUBE
RETAINING
TAB
DASHBOARD
CENTER
LOWER
COVER
2 CLIPS
9 CLIPS
DRIVER’S
DASHBOARD
LOWER COVER
5.
7D2003AX
7.
Remove the driver’s console side trim (three clips
and one retaining tab).
4 of 28
CENTER
POCKET
CENTER
POCKET
Open.
RETAINING
TAB
3 CLIPS
7D2005AX
Open the center pocket, and pull the center pocket
out towards you.
DASHBOARD
CENTER LOWER
COVER
DASHBOARD
CENTER LOWER
COVER
DRIVER’S
CONSOLE
SIDE TRIM
PASSENGER’S
CONSOLE SIDE
TRIM
841020AB
7D2004AX
AII 46956 (1111)
8.
Remove the dashboard center lower cover (three
self-tapping screws, five clips, six retaining tabs, and
unplug the vehicle connectors).
10. Pull back the weatherstrip from the left kick panel.
Remove the left kick panel (one screw clip and one
clip).
VEHICLE
CONNECTORS
WEATHERSTRIP
3 CLIPS
4
SCREW
CLIP
6 RETAINING
TABS
CLIP
3 SELFTAPPING
SCREWS
LEFT KICK
PANEL
7D2008AX
DASHBOARD
CENTER LOWER
COVER
2 CLIPS
9.
11. Remove the left rear door sill trim (three clips and
four retaining tabs).
7D2006BX
Remove the fuel fill door release handle. Remove
the left front door sill trim (three clips and three
retaining tabs).
4
2 RETAINING
TABS
4
RETAINING
TABS
3 CLIPS
2 CLIPS
4
FUEL FILL
DOOR RELEASE
HANDLE
CLIP
FRONT
4
LEFT REAR DOOR
SILL TRIM
4
FRONT
4
LEFT FRONT DOOR
SILL TRIM
RETAINING
TABS
7D2009AX
RETAINING
TAB
7D2007AX
AII 46956 (1111)
5 of 28
If the vehicle is equipped with a left seat belt lower anchor
bolt, continue with step 12. If not, go to step 14.
15. Lift the rear seat cushion.
REAR SEAT
CUSHION
12. Pull up the left seat belt lower anchor bolt cover, and
remove the left seat belt lower anchor bolt.
FRONT
LEFT B-PILLAR
LOWER TRIM
PANEL
4 CLIPS
RIGHT REAR
UNDER-SEAT
TRIM PANEL
7 CLIPS
LEFT SEAT
BELT LOWER
ANCHOR
BOLT COVER
LEFT REAR UNDERSEAT TRIM PANEL
7D2012AX
LEFT SEAT
BELT LOWER
ANCHOR
7D2010BX
BOLT
13. Remove the left B-pillar lower trim panel by pulling it
out toward you as shown. Go to step 15.
16. Remove the left rear under-seat trim panel (seven
clips).
17. Remove the right rear under-seat trim panel (four
clips).
14. Remove the left B-pillar lower trim panel by pulling it
out toward you as shown.
FRONT
LEFT B-PILLAR
LOWER TRIM
PANEL
7D2011BX
6 of 28
AII 46956 (1111)
18. Remove the left and right rear seat mount covers
(four clips).
LOWER MIDDLE
REAR SEAT
MOUNT COVER
RIGHT REAR
SEAT MOUNT
COVER
UPPER MIDDLE
REAR SEAT
MOUNT COVER
21. Remove the nine anchor bolts.
REAR SEAT
ANCHOR
BOLTS
REAR SEAT
2 CLIPS
REAR SEAT
ANCHOR
BOLTS
2 CLIPS
REAR
SEAT BELT
ANCHOR
BOLT
9 RETAINING
TABS
LEFT REAR
SEAT MOUNT
COVER
2 CLIPS
REAR SEAT BELT
BUCKLE ANCHOR
BOLTS
REAR
SEAT
BELT
REAR SEAT
ANCHOR
BOLTS
7D2014AX
2 CLIPS
19. Remove the upper middle rear seat mount cover
(hold the seat belt buckles down, and pull up to
release the two clips and nine retaining tabs).
20. Remove the lower middle rear seat mount cover (two
clips).
AII 46956 (1111)
7 of 28
22. Remove two caps from the rear trim panel cover
(eight retaining tabs).
4 RETAINING
TABS
CAP
REAR TRIM
PANEL
COVER
REAR
SEAT
25. Remove the right rear seat belt upper anchor bolt
cover (three retaining tabs), and remove the right
rear seat belt upper anchor bolt.
4 RETAINING
TABS
WEATHERSTRIP
CLIP
CAP
RIGHT REAR
SEAT BELT
UPPER
ANCHOR
BOLT
3 RETAINING
TABS
RIGHT REAR
SEAT BELT
UPPER
ANCHOR
BOLT COVER
RIGHT C-PILLAR
UPPER TRIM
CLIP
7D2017BX
26. Pull back the weatherstrip from the right C-pillar
upper trim. Remove the right C-pillar upper trim.
7D2015AX
•
With side airbag; release the clip partway, and
remove the right C-pillar trim by releasing the
one clip.
•
Without side airbag; remove the right C-pillar
trim by releasing the two clips.
23. Remove the rear seat. Have an assistant help you.
24. Remove the rear trim panel cover (two clips, two
retaining tabs, and six clips).
RETAINING
TAB
27. Remove the right rear door sill trim (three clips and
four retaining tabs).
6 CLIPS
REAR TRIM
PANEL COVER
3 CLIPS
RETAINING
TABS
RETAINING
TAB
2 CLIPS
FRONT
7D2016AX
RETAINING
TABS
8 of 28
AII 46956 (1111)
RIGHT REAR
DOOR SILL TRIM
832511AX
28. Pull up the right rear seat belt lower anchor bolt
cover, and remove the right rear seat belt lower
anchor bolt.
REAR TRIM
PANEL
RIGHT C-PILLAR
LOWER TRIM
CLIP
2 CLIPS
RIGHT
REAR
SEAT
BELT
LOWER
ANCHOR
BOLT
COVER
RIGHT REAR
SEAT BELT LOWER
ANCHOR BOLT
7D2018CX
3 CLIPS
7D2020AX
33. Remove two roof rear trim bolt covers (six retaining
tabs). Remove two roof trim nuts.
29. Remove the upper clip, then remove the right C-pillar
lower trim by releasing the two clips.
3 RETAINING
TABS
ROOF REAR
TRIM BOLT
COVER
30. Repeat steps 25 through 29 to remove the left
C-pillar upper and lower trim.
If the vehicle is equipped with a subwoofer, continue with
step 31. If not, go to step 32.
31. Unplug the vehicle connector. Remove the four
bolts, and remove the subwoofer by pulling upward
to release the two hooks.
ROOF
TRIM
NUT
3 RETAINING
TABS
ROOF REAR
TRIM BOLT
COVER
ROOF
TRIM
NUT
2 HOOKS
ROOF TRIM
SUBWOOFER
7D2021AX
VEHICLE
CONNECTOR
4 BOLTS
7D2019AX
32. Remove the rear trim panel (three clips).
AII 46956 (1111)
9 of 28
34. Using a plastic trim tool, carefully pry up the front of
the roof trim to release the three front clips. Start with
the left clip, and work your way to the right clip.
38. Remove seven vehicle grommets from the roof
panel, and install six new oval grommets and one
new round grommet into the roof panel as shown.
NEW ROUND
GROMMET
7 CLIPS
PLASTIC
TRIM TOOL
ROOF PANEL
ROOF TRIM
6 NEW
OVAL
GROMMETS
VEHICLE
GROMMET
Discard.
6 VEHICLE
GROMMETS
Discard.
RIGHT CLIP
Finish here.
LEFT CLIP
Start here.
7D2024AX
7D2022BX
35. Gently lift the front of the roof trim to release four
remaining clips.
36. Gently pull up the roof trim by releasing two hooks.
39. On the roof trim backside, remove seven vehicle
clips from the roof trim, and install seven new clips to
the roof trim.
ROOF TRIM
ROOF TRIM
2 HOOKS
HIGH-MOUNT
BRAKE LIGHT
GROMMET
7 NEW
CLIPS
ROOF PANEL
2 VEHICLE
CONNECTORS
ANTENNA
GROMMET
7 VEHICLE CLIPS
Discard.
7D2025AX
7D2023BX
37. Remove the antenna grommet and high-mount
brake light grommet from the roof panel, unplug the
vehicle connectors, and remove the roof trim.
10 of 28
AII 46956 (1111)
40. Remove the screw cover from the rear of the right
bed rail trim (four retaining tabs).
6 CLIPS
SCREW COVER
43. Remove the right C-pillar outer trim (slide rearward,
and unplug the vehicle connector).
4 RETAINING
TABS
RIGHT C-PILLAR
OUTER TRIM HOLDER
3 VEHICLE CLIPS
Remove.
3 VEHICLE
CLIPS
Install.
SELFTAPPING
SCREW
VEHICLE
PANEL
VEHICLE
PANEL
VEHICLE
CONNECTOR
RIGHT BED
RAIL TRIM
RIGHT C-PILLAR
OUTER TRIM
3 CLIPS
852225AB
7D2029AX
41. Remove one self-tapping screw from the rear of the
right bed rail trim.
42. Pull the right bed rail trim back to release the six
clips, and remove the right bed rail trim.
44. Remove the three vehicle clips from the vehicle
panel, and install them to the right C-pillar outer trim
holder.
45. Remove the right front upper tie-down hook (two
T-50 torx bolts). Repeat the same procedure for the
left side.
RIGHT FRONT
UPPER TIE-DOWN
HOOK
T-50 TORX
BOLTS
852226AB
AII 46956 (1111)
11 of 28
46. Remove the front board panel (six T-40 torx bolts).
If the vehicle is equipped with a bed extender, continue
with step 48. If not, go to step 49.
48. Remove the right latch (three hex bolts).
RIGHT SIDE
BED LINING
FRONT BOARD
PANEL
6 T-40 TORX
BOLTS
HEX
BOLTS
7D2028AX
47. Remove two right rear tie-down hooks (four T-50 torx
bolts).
RIGHT LATCH
7D2031BX
49. Remove the right side bed lining (five T-40 torx bolts,
one clip, and unplug the vehicle connector).
RIGHT SIDE
BED LINING
CLIP
VEHICLE
CONNECTOR
2 RIGHT REAR
TIE-DOWN
HOOKS
5 T-40 TORX
BOLTS
T-50 TORX
BOLTS
7D2032BX
7D2030BX
12 of 28
AII 46956 (1111)
50. Remove the left taillight (two bolts, two clips, release
the vehicle connectors from the vehicle panel, and
unplug the vehicle connector). Repeat the same
procedure for the right side.
VEHICLE
PANEL
LEFT SIDE
51. Remove the right license plate light (three retaining
tabs and unplug the vehicle connector). Repeat the
same procedure for the left side.
VEHICLE
PANEL
3 RETAINING
TABS
RIGHT SIDE
RIGHT LICENSE
PLATE LIGHT
VEHICLE
CONNECTOR
VEHICLE
CONNECTORS
VEHICLE
CONNECTORS
BOLTS
REAR BUMPER
FRONT
2 CLIPS
841501AY
VEHICLE
CONNECTOR
LEFT TAILLIGHT
VEHICLE
CONNECTOR
7D2033AX
AII 46956 (1111)
13 of 28
52. Remove the license plate from the rear bumper (two
bolts).
Without rear under spoiler
53. Remove the rear bumper (two bolts, ten self-tapping
screws, and six clips). Have an assistant help you.
Place the rear bumper on a blanket.
REAR BUMPER
With rear under spoiler
LICENSE PLATE
REAR BUMPER
LICENSE PLATE
BOLTS
2 CLIPS
2 SELFTAPPING
SCREWS
BOLTS
2 CLIPS
2 SELFTAPPING
SCREWS
BOLTS
REAR
BUMPER
REAR
BUMPER
4 CLIPS
8 SELF-TAPPING
SCREWS
841601AY
BOLTS
8 SELFTAPPING
SCREWS
4 CLIPS
REAR UNDER
Remove these clips.
SPOILER
REAR BUMPER
14 of 28
7D2034BX
AII 46956 (1111)
54. On the inside of the rear bumper, locate the back-up
sensor preset marks on the left side. Using a
pushpin, pierce the holes at the left and center
preset marks. There are two sets of marks on the
rear bumper, use the lower marks. Repeat the same
procedure for the right side.
LEFT PRESET
MARK
MARKS
Do not use
these marks.
CENTER
PRESET
MARK
If the vehicle is equipped with a rear under spoiler,
continue with step 56. If not, go to step 57.
56. Remove the left and right bumper absorbers. Locate
the scribe mark on the left bumper absorber. Using a
utility knife, cut out the left bumper absorber along
the scribe mark as shown. Repeat the same
procedure for the right bumper absorber.
Go to step 58.
LEFT BUMPER
ABSORBER
REAR BUMPER
LEFT BUMPER
ABSORBER
PUSHPIN
7D2035AX
55. While wearing eye protection, drill one 20 mm hole
through the outer mark, and one 26 mm hole
through the inner mark on the rear bumper. First
drill with a 3 mm drill bit. Finish the outer hole with a
20 mm hole saw. Finish the inner hole with a
26 mm hole saw. Remove any burrs. Repeat the
same procedure for the right side.
SCRIBE
MARK
Cut out.
832601AX
MARKS
REAR
BUMPER
3 mm
DRILL
BIT
3 mm
DRILL BIT
20 mm
HOLE SAW
DRILL
26 mm
HOLE SAW
DRILL
7D2037AX
AII 46956 (1111)
15 of 28
57. Remove the left and right bumper absorbers. Locate
the scribe mark on the left bumper absorber. Using a
utility knife, cut out the left bumper absorber along
the scribe mark as shown. Repeat the same
procedure for the right bumper absorber.
View of the top side
58. Slide the two center sensors into the 26 mm holes
with the “UP” mark facing up. Secure the center
sensors with two retainer clips.
RETAINER CLIP
“UP”
MARK
LEFT
BUMPER
ABSORBER
CENTER
SENSOR
REAR BUMPER
15 mm
35 mm
CORNER
SENSOR
26 mm HOLE
Cut out.
15 mm
CORNER
SENSOR
Cut out.
LEFT
BUMPER
ABSORBER
CENTER
SENSOR
SCRIBE
MARK
CENTER
SENSOR
20 mm HOLE
CORNER
SENSOR
LEFT
BUMPER
ABSORBER
“UP” MARK
7D2039AX
CORNER
SENSOR TRIM
CORNER
SENSOR
“UP”
MARK
7D2038AX
59. Separate the corner sensors from the corner sensor
trims. First install the corner sensor trim into the 20
mm holes with the “UP” mark facing up, then install
the corner sensors through the corner sensor trim
with the “UP” mark on the sensor facing up.
16 of 28
AII 46956 (1111)
60. Place a shop towel below the tailgate latch to catch
any metal shavings. Attach adhesive tape inside the
tailgate panel with the tape adhesive facing up to
catch any metal shaving.
62. While wearing gloves and eye protection, drill one 26
mm hole and four 8 mm holes through the marked
locations. First drill with a 3 mm drill bit, then finish
the center hole with a 26 mm hole saw. Finish the
outer holes with an 8 mm drill bit.
TAILGATE
LATCH
ADHESIVE TAPE
Position with
adhesive facing up.
5 MARKS
3 mm
DRILL BIT
26 mm
HOLE SAW
TAILGATE
PANEL
SHOP TOWEL
61. Position the template on the tailgate panel. Using a
center punch, mark the tailgate panel at five holes
indicated on the template. Remove the template.
CENTER
PUNCH
TAILGATE
DRILL
3 mm
8 mm
DRILL BIT
7D2107AX
7D2109AX
63. Remove any burrs from the edges of the holes, and
apply touch-up paint. Allow the touch-up paint to dry
thoroughly before proceeding to the next step.
Remove the shop towel, adhesive tape, and any
metal shavings.
64. Insert two well nuts into the upper and lower holes.
5 MARKS
UPPER
HOLE
2 WELL
NUTS
TEMPLATE
2 WASHERSCREWS,
4 x 14 mm
TEMPLATE
7D2108BX
LOWER
HOLE
TAILGATE SWITCH
BRACKET
7D2110AX
65. Install the tailgate switch bracket to the vehicle with
two 4 x 14 mm washer-screws.
AII 46956 (1111)
17 of 28
66. Cut 50 mm from the end of the corrugated tube.
69. Attach the 2A fuse label to the back-up sensor
harness fuse case.
CORRUGATED TUBE
50 mm
FUSE CASE
2-PIN
CONNECTOR
Align.
FUSE LABEL
(2A)
Discard.
CORRUGATED
TUBE
BACK-UP
SENSOR
HARNESS
WIRE
INSULATION
TAPE
TAILGATE
SWITCH
7D2111AX
7D2041AX
67. Install the corrugated tube around the wires on the
tailgate switch, align the corrugated tube to the 2-pin
connector, and secure the tube to the tailgate switch
with insulation tape.
68. Insert the tailgate switch 2-pin connector into the
26 mm hole, and install the tailgate switch onto the
tailgate switch bracket with two 4 x 14 mm
washer-screws.
TAILGATE SWITCH
BRACKET
2 WASHERSCREWS,
4 x 14 mm
TAILGATE SWITCH
2-PIN CONNECTOR
18 of 28
TAILGATE
SWITCH
7D2112AX
AII 46956 (1111)
70. Inside the passenger’s compartment, remove the
two vehicle foam blocks from the vehicle panel.
BACK-UP
SENSOR
HARNESS
VEHICLE
FOAM BLOCKS
73. Install the back-up sensor harness grommet into the
vehicle grommet hole.
PASSENGER’S COMPARTMENT
VEHICLE
PANEL
VEHICLE
PANEL
INSIDE
OUTSIDE
VEHICLE
GROMMET
HOLE
FRONT
VEHICLE
PANEL
BACK-UP
SENSOR
HARNESS
GROMMET
VEHICLE
PANEL
VEHICLE
GROMMET
Discard.
VEHICLE
GROMMET
HOLE
BACK-UP
SENSOR
HARNESS
7D2101AX
BACK-UP
SENSOR
HARNESS
7D2042BX
71. Inside the cargo area, remove the vehicle grommet
from the vehicle panel.
72. Route the back-up sensor harness into the vehicle
grommet hole, and into the passenger’s
compartment.
AII 46956 (1111)
19 of 28
74. Install a wire tie with small clip at the green tape on
the back-up sensor harness as shown. Inside the
cargo area, route the back-up sensor harness along
the vehicle harness, and secure the front of the
back-up sensor harness to the hole in the vehicle
panel with one wire tie with small clip.
WIRE TIE WITH
SMALL CLIP
BACK-UP
SENSOR
HARNESS
HOLE
WIRE TIE WITH
LARGE CLIP
Not used here.
Large
77. Route the back-up sensor harness along the vehicle
harness, and through the right taillight opening.
Secure the back-up sensor harness to the vehicle
harness with three wire ties.
BACK-UP SENSOR
HARNESS
RIGHT TAILLIGHT
OPENING
WIRE TIE
WITH SMALL
CLIP
Use this clip.
Small
FRONT
GREEN
TAPE
WIRE
TIES
VEHICLE
HARNESS
VEHICLE
PANEL
WIRE
TIES
VEHICLE
HARNESS
WIRE
TIE
VEHICLE
HARNESS
BACK-UP
SENSOR
HARNESS
WIRE
TIES
7D2103AX
78. Using scissors, cut a EPT sealer into three equal
pieces.
EPT
SEALER
BACK-UP
SENSOR
HARNESS
7D2102CX
EPT
SEALER
75. Secure the back-up sensor harness to the vehicle
harness with five wire ties.
76. Using isopropyl alcohol on a shop towel, clean the
area near the wire tie with small clip where the EPT
sealer will attach. Secure the back-up sensor
harness to the vehicle panel with one EPT sealer.
20 of 28
AII 46956 (1111)
7D2133BX
areas where the EPT sealers will attach. Attach two
pieces of EPT sealer to the edge of the vehicle panel
as shown.
82. Route the back-up sensor harness along the rear
bumper area, and secure it to the vehicle harness
with eight wire ties.
TAILGATE PANEL
WIRE TIES
TAILGATE
PANEL
EPT SEALER
BACK-UP
SENSOR
HARNESS
VEHICLE
PANEL
WIRE
TIES
VEHICLE
HARNESS
VEHICLE
HARNESS
FRONT
VEHICLE
PANEL
GREEN
TAPE
7D2104BX
80. Plug the back-up sensor harness 2-pin connector
into the tailgate switch 2-pin connector.
BACK-UP SENSOR
2-PIN CONNECTOR
EPT SEALER
7D2113CX
area where the EPT sealer will attach. Secure the
back-up sensor harness to the vehicle panel with
one EPT sealer at the green tape.
TAILGATE SWITCH
2-PIN CONNECTOR
EPT SEALER
TAILGATE SWITCH
2-PIN CONNECTOR
VEHICLE
PANEL
FRONT
7D2114BX
area where the EPT sealer will attach. Secure the
back-up sensor harness to the vehicle frame with
one piece of EPT sealer.
AII 46956 (1111)
21 of 28
84. Using scissors, cut one EPT sealer in half.
EPT SEALER
Cut in half.
2 BACK-UP SENSOR
2 PIECES OF 2-PIN CONNECTORS
EPT SEALER
87. Under the rear bumper, secure the center sensor
2-pin connectors and the center sensor harnesses to
the vehicle brackets with two wire ties with large clips
as shown.
2 CENTER SENSOR WIRE TIES WITH
2-PIN CONNECTORS LARGE CLIPS
BACK-UP
SENSOR
HARNESS
VEHICLE
BRACKET
2 CENTER SENSOR
2-PIN CONNECTORS
REAR
BUMPER
2 CENTER
SENSOR
HARNESSES
VEHICLE
BRACKET
BACK
VEHICLE
BRACKET
Large
Small
REAR
BUMPER
2 BACK-UP SENSOR
2 CORNER SENSOR 2-PIN CONNECTORS
2-PIN CONNECTORS
VEHICLE
BRACKET
7D2105BX
85. Reinstall the bumper absorbers. With the help of an
assistant, hold the rear bumper close to the vehicle.
Route the back-up sensor harness 2-pin connectors
through the holes in the bumper absorbers, and plug
them to the corner sensor and the center sensor
2-pin connectors.
WIRE TIE
WITH LARGE
CLIP
Use this clip.
WIRE TIE
WITH SMALL
CLIP
Not used here.
7D2106FX
86. Wrap two pieces of EPT sealer around the center
sensor 2-pin connectors, and reinstall the rear
bumper.
22 of 28
AII 46956 (1111)
88. Inside of the vehicle, pull back the floor mat. Route
the back-up sensor harness across the vehicle panel
and alongside the vehicle harness.
VEHICLE FOAM
BLOCKS
CUSHION TAPE
92. Slide the control unit bracket onto the control unit.
CONTROL UNIT
BRACKET
2 CUSHION TAPES
Cut in half.
CONTROL
UNIT
VEHICLE
HARNESS
WIRE
TIES
WIRE
TIE
FRONT
FLOOR
MAT
7D2116AX
VEHICLE
HARNESS
VEHICLE
PANEL
7D2115CX
BACK-UP SENSOR
HARNESS
89. Using scissors, cut two cushion tapes in half. Using
isopropyl alcohol on a shop towel, clean the areas
where the cushion tapes will attach. Secure the
back-up sensor harness to the vehicle panel with
three pieces of cushion tape.
into the control unit, and insert the control unit
bracket into the hole in the vehicle panel. Secure the
control unit bracket with one flange bolt.
CONTROL UNIT
BRACKET
HOLE
VEHICLE
PANEL
90. Secure the back-up sensor harness to the vehicle
harness with four wire ties. Do not secure the wire tie
to the SRS harness.
91. Reinstall the two vehicle foam blocks removed in
step 70.
FLANGE
BOLT
FRONT
CONTROL
UNIT
AII 46956 (1111)
BACK-UP SENSOR
HARNESS
22-PIN CONNECTOR
7D2117AX
23 of 28
94. Unplug the vehicle 23-pin and 14-pin connectors.
Release the connector lock on the vehicle 23-pin
connector.
VEHICLE 23-PIN
CONNECTOR
harness, and secure it to the vehicle harness with
four wire ties and two small wire ties in the area
shown.
VEHICLE
23-PIN
CONNECTOR CONNECTOR
LOCK
WIRE
TIES
HARNESS
SIDE VIEW
BACK-UP
SENSOR
HARNESS
TERMINAL
VEHICLE
23-PIN
CONNECTOR
BACK-UP
SENSOR
HARNESS
TERMINAL
VEHICLE
HARNESS
CONNECTOR
LOCK
VEHICLE 14-PIN
CONNECTOR
WIRE
TIES
VEHICLE 23-PIN
CONNECTOR
BACK-UP
SENSOR
HARNESS
TERMINAL
BACK-UP
SENSOR
HARNESS
FRONT
SMALL
WIRE TIES
7D2119AX
four small wire ties.
SMALL
WIRE TIE
VEHICLE
HARNESS
FRONT
BACK-UP
SENSOR
HARNESS
FRONT
7D2118AX
95. Push the back-up sensor harness terminal into the
vehicle 23-pin connector, then reattach the
connector lock. Re-plug the vehicle 23-pin and
14-pin connectors.
BACK-UP
SENSOR
HARNESS
SMALL
WIRE TIES
24 of 28
AII 46956 (1111)
7D2120AX
three small wire ties.
100. Route the back-up sensor harness as shown, and
secure it to the vehicle harness and the vehicle
frame with six wire ties.
WIRE TIES
BACK-UP SENSOR
HARNESS
VEHICLE
HARNESS
VEHICLE
FRAME
FRONT
WIRE
TIES
BACK-UP
SENSOR
HARNESS
SMALL
WIRE TIES
7D2121AX
WIRE
TIES
99. At the fuse box, remove the upper hood opener bolt.
Secure the back-up sensor harness ground terminal
with the ground bolt.
FUSE BOX
Do not
close the
clip hole.
FUSE
BOX
UPPER HOOD
OPENER BOLT
Discard.
VEHICLE
HARNESS
7D2123AX
If the vehicle is equipped with a security system: Wrap
one cushion tape around the back-up sensor harness,
and secure it to the security system bracket with one wire
tie.
WIRE TIE
GROUND
BOLT
BACK-UP SENSOR
HARNESS GROUND
TERMINAL
HOOD
OPENER
7D2122BX
BACK-UP
SENSOR
HARNESS
AII 46956 (1111)
SECURITY
SYSTEM
BRACKET
CUSHION
TAPE
7D2124AX
25 of 28
three wire ties. If there is any excess, bundle it to the
vehicle harness after step 105.
WIRE
TIE
BACK-UP SENSOR
HARNESS
103. Remove the front vehicle bolt from the vehicle frame,
and loosen the back vehicle bolt.
BACK-UP SENSOR
HARNESS 5-PIN
CONNECTOR
BUZZER
VEHICLE
HARNESS
VEHICLE
FRAME
VEHICLE
HARNESS
WIRE
TIES
FRONT VEHICLE
BOLT
Remove.
BUZZER
BRACKET
BACK-UP
SENSOR
HARNESS
7D2125BX
102. Install the buzzer bracket to the buzzer with one
6 x 12 mm washer-screw and one flange nut. Do not
pinch the wire on the buzzer.
BACK VEHICLE
BOLT
Loosen.
7D2127AX
into the buzzer.
105. Insert the buzzer bracket between the vehicle frame
and the back vehicle bolt, and install the buzzer
bracket to the vehicle frame with two bolts.
106. Using a pushpin, mark the inside of the driver’s
dashboard lower cover at the preset mark.
FLANGE
NUT
BUZZER
PUSHPIN
WASHERSCREW,
6 x 12 mm
BUZZER
BRACKET
DRIVER’S DASHBOARD
LOWER COVER
7D2126AX
PRESET
MARK
26 of 28
AII 46956 (1111)
7D2128AX
107. While wearing eye protection, drill one 26 mm hole
through the marked position. First drill with a 3 mm
drill bit, then finish with a 26 mm hole saw. Remove
any burrs.
into the switch.
DRILL
3 mm
DRILL BIT
26 mm
HOLE SAW
LOWER COVER
MARK
SWITCH
BACK-UP SENSOR HARNESS
3-PIN CONNECTOR
7D2129BX
108. Reinstall the driver’s dashboard lower cover. Insert
the switch connector into the hole in the driver’s
dashboard lower cover, then turn the switch to install
it to the driver’s dashboard lower cover.
7D2131AX
area where the EPT sealer will attach. Attach the
EPT sealer to the driver’s console side trim in the
area shown.
EPT SEALER
LOWER COVER
HOLE
DRIVER’S CONSOLE
SIDE TRIM
SWITCH
CONNECTOR
7D2132AX
SWITCH
7D2130AX
AII 46956 (1111)
27 of 28
111. Check that all wire harnesses are routed properly
and all connectors are plugged in.
112. Reinstall all removed parts. Check that all clips and
fasteners are installed securely.
NOTE:
• Torque the seat belt upper anchor bolts (steps 25 and
28) to 32 N•m (24 lb-ft).
• Use these torque specs when reinstalling the anchor
bolts to the rear seat (step 21):
- Rear seat belt anchor bolt, 32 N•m (24 lb-ft)
- 6 rear seat belt buckle anchor bolts, 22 N•m (16 lb-ft)
- 2 rear seat anchor bolts, 47 N•m (35 lb-ft)
• If reinstalling the left seat belt lower anchor bolt cover
(step 12), torque the bolt to 32 N•m (24 lb-ft).
113. Reconnect the negative cable to the battery.
114. Enter the customer’s radio anti-theft code, and reset
the radio station presets.
115. Reset the clock.
116. Check the operation of the back-up sensors
according to the Accessory User’s Information
Manual.
NOTE: Whenever the battery is disconnected, the driver’s
window AUTO function is disabled.
117. Start the engine. Push down on the driver’s window
switch until the window is fully open.
118. Pull up on the driver’s window switch to close the
window completely, then hold the switch for
2 seconds or more.
119. Test the window AUTO function.
28 of 28
AII 46956 (1111)

View the Installation Instructions

Transcription

Similar documents