TM-1052 - Tadano

BOOM TRUCK
HYDRAULIC
Hydraulic motor
Control valves
Recommended Hydraulic pump
Reserve tank
Axial piston type for winch and swing
Multiple control valves with integral safety valve
Pressure : Max. 20.6Mpa
Delivery : Max. 60L/min
90 L capacity
*PTO/Mounting not included
ELECTRICAL SYSTEM
Power supply
DC24V
SAFETY DEVICE
Pendant type over - winding cutout
Load meter
Load indicator
Hook safety latch
Level gauge
Hydraulic safety valves, check valves and holding valves
BOOM REST
No required
LOCALLY PROVIDED EQUIPMENT
Crane mounting parts (Include P.T.O, P.T.O Mounting)
CRANE WEIGHT
Approx. 3,135 kg (crane bare)
REAR OUTRIGGERS WEIGHT
Approx. 281kg (Outriggers, mountings, etc. included)
The TADANO TM-1052 is the only true 8 ton telescopic crane offered today. With a tip height of
about 18 m, this crane answers the demand for a compact, continuous rotation hydraulic crane
that can be mounted in a number of configurations.
If you are in the market for a true 8 ton crane, the TADANO TM-1052 has the features everyone is
asking for in a versatile crane package.
TADANO builds a vast range of cranes from 0.5 ton to 550 tons. No matter what your reach or lift
requirements are, TADANO can provide you with a great solution. Put one to work for you now.
Call today or visit our web site for more information.
Features:
Exceptional Reach without a Jib: 15.92 m. Full powered partly synchronized Boom
Self-Aligning Pentagonal Shaped Boom: reducing maintenance cost
Light Weight: increases payload
Out & Down Mainframe Outriggers: complete level ability
Multiple Outrigger Span: easy to set up in various job sites
Faster Function Speeds: increase productivity
Superior Winch Performance: up to 60 m/min. increase productivity
Large Hydraulic Reservoir: superior cooling capabilities
Operator Friendly: dual control stations with exceptional job site viewing
Stand-Up operation levers with higher operation
position gives the better view
Cat-Walks gives you easy access to the other side of a truck.
*Cat-Walk shall be designed at TADANO dealer with your requirements.
Ask today for your future business solution
Continuing technical development requires Tadano to retain the right to
make specifications, equipment and price changes without notice.
*Some specifications are subject to change
TADANO LTD. (International Division)
These pictures show some optional devices which are not available on your crane.
4-12, Kamezawa 2-chome, Sumida-ku Tokyo 130-0014, Japan
Phone: 81-3-3621-7750 Fax: 81-3-3621-7785
http://www.tadano-global.com E-mail: [email protected]
2013-04
Printed in Japan
TM-1052
MAXIMUM LIFTING CAPACITY : 8.2 TON
Outriggers Max.
Outriggers Min.
and below
4.4 m Boom
8,200
7.28 m Boom
6,000
2.9
3.5
6,000
5,000
4,200
6,000
10.16 m Boom
13.04 m Boom
Extended Min.
Extended Mid.
Extended Max.
4.5
4.6
5.0
6.0
7.0
8.0
9.0
10.0
11.0
3,700
3,200
3,100
2,700 2,000
1,550(7.03m)
3,000
3,000
3,000
3,000
3,000
2,700 1,900
1,500
1,200 1,000
850 (9.91m)
3,000
3,000
3,000
3,000
2,900
2,600 1,900
1,500
1,200 1,000
850
2,600
13.0
15.9
2m
2,600
2,600
2,600
2,600 1,900
1,500
1,200 1,000
850
750
750
10.1
6
650
650
600 (12.7m)
550
500
7.28
Extension Mark
4.4
m
Boom
7.28 m Boom
10.16m
4
13.04m
4
BO
O
10°
5
10
Working Radius (m)
0
15
1
No. of part lines
Max. of load
1,500kg
<CAB BACK MOUNTED>
8,200
6,000
5,000
4,200
3,550 (4.15m)
6,000
6,000
5,000
4,200
3,700
3,300
3,200
2,900 2,200
1,750(7.03m)
3,000
3,000
3,000
3,000
3,000
2,700 2,200
1,800
1,400 1,150 1,000(9.91m)
3,000
3,000
3,000
3,000
2,900
2,600 2,000
1,700
1,400 1,150
1,000
900
750
650 (12.7m)
2,600
2,600
2,600
2,600
2,600 2,000
1,650
1,400 1,150
1,000
900
750
650
4.0
4.5
4.6
5.0
6.0
7.0
Notes:
8.0
9.0
10.0
11.0
12.0
13.0
Extension Mark
(mm)
14.0 15.67
550
CA: 3,500 MIN 5,590 MAX
5,260 MIN 7,470 MAX
450
Rated Lifting Capacities are based on crane strength only. Capacities based on stability may be lower than those in above table depending on loading conditions and types of chassis.
Bare Chassis Rated capacities on this chart are maximum allowable loads with the outriggers properly extended on a firm level surface and the crane
leveled and mounted on a factory recommended truck.
All capacities incluide mass of hook block (90kg), sling, etc.
Load radii mean actual ones including effects of loaded boom deflection.
For operation forward of outriggers, reduce load values to 25% of Bare Chassis Rated Capacities.
For boom length not shown, use rating of next longer boom.
For boom length longer than 10.16m extend outriggers to max. position
13.04m boom means mark on 4th boom section side plate is half seen.
Standard number of part lines for each boom is as shown the below table. The single line load shall not exceed 14.7kN (1,500kgf).
This mount requires, rear stabilizers, and additional counterweight
in the underside of the truck.The complete unit must be installed in
accordance with factory requirements and a test performed to
determine actual stability and counterweight requirements for
variety of trucks.
Over-front area
Extended Min.
Extended Mid.
Extended Max.
250
(mm)
MIN.4,400 MAX.15,920
4,266
67.5
2,417
Over-rear area
Over-side area
Outriggers Mid.
Center of rotation
7.28m
4
6
9,000kg
10.16m
4
13.04m
4
15.92m
4
Gross axle weight rating(GAWR),front
Gross axle weight rating(GAWR),rear
Gross vehicle weight
Cab to Axle(CA)
Frame Section Modulus(SM)
under crane; (per rail)
Frame Section Modulus(SM)
over rear spring hanger; (per rail)
P.T.O. torque
P.T.O. revolution
Width for crane mounting
Frame width range (inside to outside)
Frame height (ground to frame top)
8.2
Over-side area
4.4m
6
4
6,000kg
Full capacity work area
225
810
160
MIN. 2,250
MID.3,300
MAX.4,300
(This dimension depends on jack floats applied.)
* Outrigger jack stroke 580mm
CAPACITY; B
CAPACITY; D
5,300 kg or more
5,500 kg or more
7,500 kg or more
9,500 kg or more
12,800 to 25,000 kg 15,000 to 25,000 kg
3,505 to 5,588 mm
245 (cm3)
7.57 x 104 (N/cm2)
540 (cm3)
2.98 x 104 (N/cm2)
165 (cm3)
7.57 x 104 (N/cm2)
360 (cm3)
2.98 x 104 (N/cm2)
21.804N m Min.
Approx. 350 to 1,750 rpm
Approx. 1,114 mm min.
Approx. 610 mm to 953 mm
Approx. 1,066mm max.
(Height of crane mounting base can be
changed by combination of jack floats
and crane bases)
* Estimated axle scale weights prior to installation of crane and stabilizers for 85% stability.
Include counterweight.
Yellow: Extended Mid.
White: Extended Max.
Boom Length
No. of part lines
2
3,000kg
8.2
3.5
15.92 m Boom
20°
5
15.92m
4
2.9
13.04 m Boom
10
OO
M
Over-side area
2.4
10.16 m Boom
30°
Note)
1) Three sheaves hook block is provided with a crane.
2) The mass of a hook block, slings and all similarly used load handling
devices shall be consider as a part of load.
Outriggers Extended Max. (Over side and rear)
and below
4.4 m Boom
15
40°
The above lifting heights and boom angles are based on a straight (unladen)boom,
and allowance should be made for boom deflection obtained under laden condition.
CAPACITY CHART; D
Load radius 1.8
OM
Full capacity work area
Center of rotation
Outriggers
50°
Over-rear area
Extended Min.
Extended Mid.
Extended Max.
7.28m
4
60°
mB
OO
M
0
Yellow: Extended Mid.
White: Extended Max.
4.4m
6
BO
BO
OM
NOTE:
1) Rated lifting capacities on this chart show maximum allowable loads with the outriggers
properly extended on a firm surface and the crane leveled and mounted on a factory
recommended truck.
2) The weight of handling devices such as hook block, slings, etc., must be considered part of the
load and must be deducted form the rated lifting capacities.
3) The operator must reduce loads to allow for such factors as wind, ground conditions, operating
speed and the effects of freely suspended loads such as boom deflection.
4) For boom length or radius not shown, use the rated lifting capacity of next longer boom
length or radius.
5) When outriggers are extended to mid. position, use the rated lifting capacities for outriggers
extended to min. position.
6) For boom lengths longer than 10.1m, extend outriggers to max. position. (in capacity chart B)
7) For boom lengths longer than 13.0 m, extend outriggers to max. position. (in capacity chart D)
8) For boom lengths longer than 13.0 m, extend outriggers to max. position. (in capacity chart D)
boom means mark on 4th boom section side plate is half visible.
9) Maximum load for number of part lines is as shown below.
1°
Over-side area
Over-front area
mB
400
Notes: Bare Chassis Rated capacities on this chart are maximum allowable loads with the outriggers properly extended on a firm level surface and the crane
leveled and mounted on a factory recommended truck.
All capacities incluide mass of hook block (90kg), sling, etc.
Load radii mean actual ones including effects of loaded boom deflection.
For operation forward of outriggers, reduce load values to 25% of Bare Chassis Rated Capacities.
For boom length not shown, use rating of next longer boom.
For boom length longer than 10.16m extend outriggers to max. position
13.04m boom means mark on 4th boom section side plate is half seen.
Standard number of part lines for each boom length is as shown the below table. The single line load shall not exceed 14.7kN (1,500kg)
Boom Length
No. of part lines
70°
14.0 15.67
13.0
4m
4,200
15.92 m Boom
12.0
3,550 (4.15m)
5,000
Yellow: Extended Mid.
White: Extended Max.
Outriggers Mid.
4.0
2,522
Yellow: Extended Mid.
White: Extended Max.
Extended Min.
Extended Mid.
Extended Max.
Outriggers Max.
Outriggers Min.
Boom
2.4
20
82°
Outriggers Extended Max. (Over side and rear)
Load radius 1.8
(m)
703
<REAR MOUNTED>
Outriggers
stroke
580
<CAB BACK MOUNTED>
WORKING RANGE
1,055 MAX 1,880 MAX
<REAR MOUNTED>
Rear outriggers (Out & Down type)
Hydraulically extended sliders and hydraulically extended jacks, integral with crane frame
Extend width
Min. 2,250 mm
Mid. 3,300 mm
Max. 4,300 mm
RATED LIFTING CAPACITY (IN KILOGRAMS)
CAPACITY CHART; B
M
MAXIMUM LIFTING CAPACITY
8,200 kg at 1.8m (6-part lines)
BOOM
5-sectioned, fully powered partly synchronized telescoping boom of pentagonal box construction
Retracted length
4.40 m
Extended length
15.92 m
Extended speed
11.52 m / approx. 32 s
Elevation
Elevated by double-acting hydraulic cylinder
Elevation speed
1˚ to 82˚ / approx. 14 s
NOTE: Extended speed and elevation speed are calculated under the condition that the flow is 80L / min.
Boom point
3 sheaves
WINCH
Hydraulic motor driven, planetary gear speed reduction, provided with automatic brake and cable follower
Single line pull
14.7 kN {1,500 kgf}
Single line speed
60 m/min (at 4th layer)
NOTE: Single line speed is calculated under the condition that the flow is 15.8 GPM
Wire rope
Diameter x length
10 mm x 95 m
Breaking strength
73.5 kN {7.5 tf}
Hook block
3 sheaves (For maximum lifting load)
SWING
Hydraulic motor driven, Worm gear speed reduction, Continuous
360˚ full circle swing on ball bearing slew ring, Automatic swing lock
Swing speed
2.5 min-1 {rpm}
OUTRIGGERS
<CAB BACK MOUNTED>
Outriggers (Out & Down type)
Hydraulically extended sliders and hydraulically extended jacks, integral with crane frame
Extend width
Min. 2,250 mm
Mid. 3,300 mm
Max. 4,300 mm
Rear stabilizers (Straight Down type) *OPTIONAL ITEM
Hydraulically extended jacks, integral with chassis frame
Span
2,250 mm
Extension Mark
for Cab Back Mout
8.2
8.2
Lifting height (m)
8.2